Page 1
PACKAGE CONTENTS
Questions, problems, missing parts?
D E
ITEM # MF750UV
Pond Boss™
REMINDER
CALL 1-888-412-6001
BEFORE RETURNING TO STORE.
Part Description Quantity
A Pond Boss™ 1
B Waterspray nozzle 1
C Waterbell nozzle insert 1
D Trumpet nozzle insert 1
E Lower fountain head nozzle 1
retailer, call our customer service department at
1-888-412-6001, 8 a.m.-6 p.m., EST, Monday-Friday, or email
us at customercare@geoglobalpartners.com. Or visit our
website www.totalpond.com.
C
Before returning to your
B
A
WARNINGS AND CAUTIONS
WARNING
• Risk of electrical shock. This unit is supplied with a grounding conductor and grounding–type
attachment plug. To reduce the risk of electric shock, be certain that it is connected only to a properly
grounded, grounding-type receptacle (GFCI).
• Do not exceed 120 volts.
• Always disconnect unit from the power source before beginning any maintenance or work on the unit.
• Inspect cord for damage before installation and/or maintenance. Replace the entire pump assembly if
damage is found.
• Do not remove the grounding pin from the power cord plug.
• Risk of electrical shock: This unit has not been investigated for use in swimming pools or marine areas.
CAUTION
• This unit has been evaluated for use with fresh water only.
• Use a proper power source as indicated on the unit label.
• Keep the cord away from high temperatures or other heat sources.
• Do not pump heated liquids.
• Do not let the unit run dry. Unit must be completely submerged up to the flotation ring for proper
operation and cooling.
• Operate in fresh water only. Avoid heavily chlorinated water and water with high pH levels.
• Do not lift the unit by its power cord.
CAUTION
• UV light may cause irritation to the skin and/or eyes. Avoid exposure.
1
Page 2
• DANGER – ULTRAVIOLET RADIATION – disconnect power before replacing lamp.
PREPARATION
OPERATION INSTRUCTIONS
• Prolonged or repeated exposure to UV light may have adverse physical effects including, severe
damage to your skin and eyes. Seek immediate medical attention for overexposure to UV radiation.
• This light assembly has not been investigated for use in swimming pools or hot tubs.
Before beginning assembly or operation of product, make sure all parts are present. Compare parts with
package contents list and diagram above. If any part is missing or damaged, do not attempt to assemble,
install or operate the product. Contact customer service for replacement parts.
• Estimated Assembly Time: 5 minutes
• Tools Required for Assembly: Philipshead screwdriver, string, rock.
1. Choose a fountain head for the desired water effect, and assemble
your choice as shown in Fig. 1.
C
B
E
D
E
Fig. 1
2. If desired, anchor the Pond Boss™ in the pond using a heavy object
(such as a rock) and some string. Cut a length of string slightly longer
than the depth of the pond. Tie one end of the string to the anchor and
the other end to the ring at the bottom of the float. Fig. 2
Fig. 2
3. Place the Pond Boss™ into the water and connect to a proper power
source. Fig. 3
GFCI
Fig. 3
2
Page 3
DISASSEMBLY
PROCE
DURE
In order to insure optimal operation of the Pond Boss™, the following procedures should be performed
periodically. When the performance of the water flow through the fountain head is reduced – it is an
indication that cleaning of the unit is needed.
1. Unplug the power cord, and then carefully remove the Pond Boss™
assembly from the pond. Fig. 4
Fig. 4
2. Turn the Pond Boss™ assembly upside down. Remove the locking
screw. Fig. 5
Fig. 5
3. Remove the fountain head and the top locking nut. Then remove the
top cover. Fig. 6
Fig. 6
4. Twist the top section counterclockwise. Then pull the top section from
the lower. Unscrew the wire connector that connects the top section to
the rest of the unit. Fig. 7
Fig. 7
3
Page 4
5. Lift the pump and filter assembly up from the fountain. NOTE: In order
CARE AND MAINTENANCE
to extract the filter assembly from the flotation basket, the main power
cord must be fed up through the bottom of the flotation basket. Fig. 8
6. Remove the filter pad and rinse until it is clean. Then reassemble the
pump and filter assembly. Fig. 9
Fig. 8
Fig. 9
• General
●
●
●
• Cleaning the Pump
●
●
●
Fig. 10
A visible drop in waterflow or increased algae in the pond is your indication that filter
pad, pump, and/or UV clarifier portion of the unit require cleaning.
Before attempting to disassemble the Pond Boss™ or clean the pump, UV clarifier or
any portion of the unit, always disconnect the unit from the power source.
Disassemble the unit in accordance with the Disassembly Procedure section of this
instruction sheet.
Insure the pump is disconnected from all other components comprising the unit.
Inspect the pump by removing the front screen and impeller assembly and clean parts
of the pump and clean in warm, soapy water.
Reassemble the pump and reposition and connect the low voltage power cables.
4
Page 5
TROUBLESHOOTING
To maximize the performance of the UV clarifier portion of the unit, periodically disassemble the unit to
clean dirt and debris from the exterior of the glass tube and reflector located in the lamp housing.
IMPORTANT NOTE:
Be sure that the entire unit is completely dry and gaskets are properly seated when reassembling
the UV clarifier.
Failure to do so will result in water leakage, which can cause damage to the light unit.
1. Disconnect the UV light from the outlet. Be sure to allow sufficient time for the light to cool before
disassembling the light.
2. Unscrew the locking ring, and pull out the light unit.
3. Carefully pull out the glass tube holder by twisting and then pull out.
4. Use warm, soapy water to clean the glass tube. Be sure to use biodegrable soap.
5. Reassemble the UV clarifier, and be sure that all gaskets and o-rings are seated properly.
If the LED lights fail to operate:
• Check to make sure the power cord is plugged in and the light is getting power and the unit is
getting power.
If the UV Clarifier fails to operate:
• Check bulb to make sure that it has not burned out. Replace the bulb as necessary or after
every season. Bulbs are available by calling the customer service department.
If the pump fails to operate:
• Check to make sure the power cord is plugged in, the pump is getting power and the pump is
fully submerged.
• Remove the inlet screen and/or pump cover, and impeller cover to expose the impeller. Turn
the impeller to ensure that it is not broken or jammed.
If the performance of the pump is not satisfactory or the pump does not flow evenly:
• Check to make sure the pump is completely submerged in water.
• Check to make sure the impeller, filter pad and the housing are clean clear of debris.
• Check the pump outlet and any tubing, fountains, spitters etc. for kinks or obstructions.
• Adjust flow control.
5
Page 6
REPLACEMENT PARTS LIST
V
U U
For replacement parts, call our customer service
department at 1-888-412-6001, 8 a.m.-6 p.m., EST,
Monday-Friday.
Part Description
B Waterspray nozzle
C Waterbell nozzle insert
D Trumpet nozzle insert
E Lower fountain head nozzle
F Flow control knob
G Front cover
H Locking ring
I Impeller cover
J Shaft support
K Washer
L Shaft
M Impeller assembly
N Float (upper)
O Float (lower)
P Screw
Q Brace
R Plug seal
S Filter pad
T Lamp housing
U Locking nut
V Lamp holder
W Small locking nut
X Inlet
Y Foil reflector
Z Glass tube
A1 UV bulb
X
T
Z
A1
Y
G
F
K
J
N
Q
O
R
S
I
H
J
K
M
L
P
B
C
D
E
Printed in China
6
Page 7
LIMITED WARRANTY
All pumps and electrical products are warranted to the user against defective material and workmanship,
under normal working conditions. This warranty period begins on the date of purchase by the original
purchaser.
All TotalPond® electrical products are warranted to the user against defective material and workmanship,
under normal working conditions for 1 year from the date of purchase. All TotalPond® liners are warranted
to the user against defective workmanship, under normal working conditions for 20 years from the date of
purchase. All other TotalPond® product is warranted to the user against defective material and
workmanship, under normal working conditions for 90 days.
Application
Warranty covers only properly installed and maintained units. Pump warranty is limited to applications
pumping fresh water in a pond or fountain only. Other liquid applications or extreme temperature uses
must be approved in writing by the manufacturer. Receipt and product date code are required for warranty
claims.
Warranty Claim
Warranty claims must be made by calling customer service (at 1-888-412-6001). If the item is
determined to be defective, you will be given authorization to return the defective part(s), freight pre-paid,
along with proof of purchase.
Disposition
The manufacturer will make a good faith effort for prompt disposition regarding all warranty claims.
Returned product will be inspected to determine cause of failure before warranty is applied. Warranty does
not cover any costs associated with the shipping, handling, installation or removal of products or parts
subject to this warranty. For products damaged in transit, a claim should be filed with the carrier.
Disclaimer
Any oral statements made about the product by the seller, the manufacturer, the representatives, or any
other parties do not constitute warranties, should not be relied upon by the user, and are not part of the
contract for sale. The seller’s and manufacturer’s only obligation, and buyer’s only remedy shall be for the
manufacturer to either replace and/or repair at the manufacturer’s sole discretion, the product as described
above. Neither seller nor the manufacturer shall be liable for injury, loss or damages for lost profits, lost
sales, injury to person or property, or any other incidental or consequential loss arising from any cause
whatsoever, no matter whether based upon warranty, contract, negligence or other misuse, and the buyer
and user agree that no other remedy shall be available to them. Before using, the buyer and user shall
determine the suitability of the product for the intended use, and assume all risk and liability whatsoever in
connection therewith. The warranty and remedy described in this limited warranty is an exclusive warranty
and remedy in lieu of any other warranty or remedy expressed or implied. All other warranties and
remedies are hereby expressly excluded, including but not limited to any implied warranty of
merchantability of fitness for any particular purpose. This warranty gives the buyer and user specific legal
rights, and buyer and user may also have other rights which vary from state to state. Some states do not
allow exclusions or limitations of incidental or consequential damages, so the above limitations or
exclusions may not apply to you.
REMINDER
CALL 1-888-412-6001
BEFORE RETURNING TO STORE.
7
Loading...