TotalPond LLUV1050 User Manual
PACKAGE CONTENTS
C
A
B
Questions, problems, missing parts?
ITEM # LLUV1050
Submersible Pond Pump with UV
950 Gallons Per Hour
REMINDER
CALL 1-888-412-6001
BEFORE RETURNING TO STORE.
Part Description Quantity
A Pump 1
B 1-in. adapter with flow control 1
C Pump barrier bag 1
retailer, call our customer service department at
1-888-412-6001, 8 a.m.-6 p.m., EST, Monday-Friday, or email
us at customercare@geoglobalpartners.com. Or visit our
website www.totalpond.com.
Before returning to your
WARNINGS AND CAUTIONS
WARNING
• Risk of electrical shock. This pump is supplied with a grounding conductor and grounding–type
attachment plug. To reduce the risk of electric shock, be certain that it is connected only to a properly
grounded, grounding-type receptacle (GFCI).
• Do not exceed the voltage shown on the pump.
• Always disconnect pump from the power source before beginning any maintenance or work on the
pump.
• Inspect cord for damage before installation and/or maintenance. Replace the entire pump assembly if
damage is found.
• Do not remove the grounding pin from the power cord plug.
• Risk of electrical shock: This pump has not been investigated for use in swimming pools or marine
areas.
CAUTION
• This pump has been evaluated for use with fresh water only.
• Use a proper power source as indicated on the pump label.
• Keep the cord away from high temperatures or other heat sources.
• Do not pump heated liquids.
• Do not let the pump run dry. Pump must be completely submerged for proper operation and cooling.
• Operate in fresh water only. Avoid heavily chlorinated water and water with high pH levels.
• Do not lift the pump by its power cord.
CAUTION
• UV light may cause irritation to the skin and/or eyes. Avoid exposure.
• DANGER – ULTRAVIOLET RADIATION – disconnect power before replacing lamp.
1
• Prolonged or repeated exposure to UV light may have adverse physical effects including, severe
PREPARATION
OPERATION INSTRUCTIONS
damage to your skin and eyes. Seek immediate medical attention for overexposure to UV radiation.
• This light assembly has not been investigated for use in swimming pools or hot tubs.
Before beginning assembly or operation of product, make sure all parts are present. Compare parts with
package contents list and diagram above. If any part is missing or damaged, do not attempt to assemble,
install or operate the product. Contact customer service for replacement parts.
• Estimated Assembly Time: 5 minutes
• Tools Required for Assembly: Philipshead screwdriver.
1. Connect the adapter to the pump by inserting into the pump
discharge and twisting clockwise. Then connect tubing to the
adapter. Fig. 1
Fig. 1
2. Route the power cord through the handle on the top of the pump.
Fig. 2
Fig. 2
3. Place the pump inside the pump barrier bag. Pull the drawstring
until the pump barrier bag is fully closed around the tubing and
power cord. Tie a knot in the drawstring. Fig. 3
Fig. 3
2
4. Place the pump into the water and connect to a proper power
MAINTENANCE PROCEDURE
GFCI
source. Fig. 4
5. Note the indicator light on the back of the pump. This light
indicates whether or not the UV light is on or off. Fig. 5
Fig. 4
Indicator
light
Fig. 5
In order to insure optimal operation of the UV pump, the following procedures should be performed
periodically. When the performance of the pump is reduced – it is an indication that cleaning of the unit
is needed.
1. Unplug pump, remove from pond. Fig. 6
Fig. 6
2. Untie the drawstring on the pump barrier bag and then remove the
pump from the pump barrier bag. Clean the pump barrier bag then
place the pump back inside the pump barrier bag and test the pump.
Untie
drawsting
Fig. 7
NOTE: If the pump performance is still unsatisfactory, unplug the
pump and proceed to step 3.
Fig. 7
3
Loading...