ELEVATE® PRESS
TM
OWNER’S GUIDE
CONGRATULATIONS
ELEVATE® PRESSTM OWNER’S GUIDE
2
CONGRATULATIONS
Thank you for choosing Total Gym® products and services.
As with all of our products, we trust that your ELEVATE Press™ will provide you with unsurpassed service and versatility year
after year.
Your Total Gym product arrives with some assembly required. In this Owner’s Guide, you will nd information how to assemble your
ELEVATE Press, and its component parts, operation, maintenance and care. Additionally, you will nd usage and safety tips, as well as
safety precautions and warranty information. Please save this guide and refer to it in the future.
We value you as a customer and your feedback is important to us. If you have any questions or need further information about your
ELEVATE Press, please contact our customer experience department at (858) 586-6080 or email support@totalgym.com.
Yours in health,
Jesse Campanaro
CEO
TABLE OF CONTENTS
®
PRESSTM OWNER’S GUIDE
TABLE OF CONTENTS
3
Safety Precautions .......................................................................................4
Parts Identier ............................................................................................. 5
Specications and Limitations .......................................................................6
Assembly Instructions ................................................................................7-8
Getting Started ............................................................................................. 8
Glideboard: Roller Removal and Assembly ......................................................9
Maintenance and Care ...................................................................................9
Maintenance Schedule ................................................................................................... 9
Exercise Instructions ..................................................................................10
Warranty Information .................................................................................. 11
USA Warranty ................................................................................................................ 11
Limited Warranty ........................................................................................................... 11
Warranty Claims ............................................................................................................ 11
SAFETY PRECAUTIONS
ELEVATE® PRESSTM OWNER’S GUIDE
SAFETY PRECAUTIONS
4
can assist in planning a program that is age and ability specic. Certain
exercise programs or types of equipment may not be appropriate for all
people. Ensure that the user is able to participate in an exercise program on
Before starting this or any exercise program, consult your physician, who
• Follow instructions in this Owner’s Guide for using the unit. Improper use could result
in severe or fatal injury. Your Total Gym ELEVATE Press must be bolted to the floor
on a flat, solid surface with nonskid material underneath. Keep the area around it
free from obstructions. The Total Gym ELEVATE Press is rated at a maximum user
weight capacity of 400 lbs [181 kg].
this equipment without injury.
• Do not overexert, or allow your clients to overexert using this equipment or while
performing any exercise program on this equipment. If any pain or tightness in
the chest occurs, an irregular heartbeat, shortness of breath, faintness, nausea or
dizziness is experienced stop the exercise session immediately and ensure that a
physician is consulted before resuming any exercise program. (Clinicians and trainers
should follow these recommendations if these symptoms are observed.)
• This product is designed and intended for commercial use. Clinicians and trainers
should inform users of and monitor their adherence to all safety precautions. Use
only as instructed.
• Children should only use the ELEVATE Press when closely attended and supervised
by an adult. Do not leave children or patients unattended on Total Gym equipment.
• Parents and others in charge of children should responsibly monitor children at all
times. A child’s mental and physical development and above all their temperament
should be taken into account while using Total Gym equipment. They should be
controlled and instructed in the correct use of the equipment.
• The equipment is under no circumstances suitable as a children’s toy.
• Keep ngers, loose clothing and hair away from moving parts. Wear appropriate
exercise attire and tie long hair back.
• Inspect your Total Gym ELEVATE Press before each use to ensure proper operation.
Check all parts for wear before each use. Do not use your Total Gym ELEVATE Press
if it is not completely assembled or if it has been damaged in any manner. Contact
Total Gym Customer Service for replacement parts or repairs.
• Before transporting, raise rails to top level. Always lift from the rear base when
moving the unit.
READ ALL INSTRUCTIONS BEFORE USING TOTAL GYM ELEVATE PRESS.
1. Inspect your Total Gym ELEVATE Press unit before each use to ensure proper
operation. Do not use this equipment unless all moving parts are working properly.
Follow all maintenance and care instructions found in this Owner’s Guide and on
the equipment labels.
2. Close supervision is necessary when the Total Gym ELEVATE Press is used by or
near children, disabled or injured persons.
3. Care should be taken at all times when getting on and off your Total Gym ELEVATE
Press or any exercise equipment. Falling on or off the product could result in injury,
or possibly death. Follow the “Getting Started” instructions for using the unit found
in this Owner’s Guide.
4. Use your Total Gym ELEVATE Press only for its intended use.
5. Keep ngers, loose clothing and hair away from all moving parts.
WARNING
PARTS IDENTIFIER
®
PRESSTM OWNER’S GUIDE
PARTS IDENTIFIER
Handle Bar
Glideboard
Handle Bar
Left Rail
Rail End Caps
Incline Release Lever
Incline Strut
5
Right Rail
Anchor Foot
Rail Base
Transport Wheel
Base Foot
Rear Struts
Rear Base
SPECS AND LIMITATIONS
100 cm
[ 32 in ]
ELEVATE® PRESSTM OWNER’S GUIDE
SPECIFICATIONS AND LIMITATIONS
6
82 cm
[ 24 in ]
60 cm
75 cm
[ 30 in ]
[ 39 in ]
• Glideboard Range of Motion: 32 inches [80 cm]
• Weight Capacity: Maximum user weight capacity of
400 lbs [181 kg]
• Resistance levels vs % of body weight:
Incline Level 1 2 3 4 5 6 7
% BW 15 20 25 35 40 45 50
• Floor Space: 14 Square Feet [1.4 Square Meters]
[ 7 in ]
17 cm
[ 32 in ]
80 cm Travel
• Size: 66” x 39 x 41” (L/W/H) [1.7 m x 1.0 m x 1.0 m]
• Weight: 116 lbs [53 kg]
• Shipping: 71.5” x 21” x 13.5” [1.8 m x .5 m x .4 m]
• GW: 130 lb [60 kg]
• Construction: Steel with steel reinforced aluminum rails
[ 41 in ]
103 cm
27°
[ 62 in ]
157 cm
ASSEMBLY INSTRUCTIONS
®
PRESSTM OWNER’S GUIDE
ASSEMBLY
TWO PERSON ASSEMBLY REQUIRED.
STEP 1. Carefully unpack all the parts and
the Information & Hardware box at the
installation site if possible.
A
Rail Base & Handle Bars
B
C
STEP 2. Open the Information & Hardware
box. Inside there will be:
13 mm
Open End Wrench
M8 Hex Head Screws
& Washers (2)
M6 Button Head
Screws & Washers (4)
Short M8 Button Head Screws & Washers (8)
Long M8 Button Head Screws & Washers (10)
4 mm
Hex Wrench
5 mm
Hex Wrench
STEP 3. Turn A upside down. Set Rail
Base & Handles in place at bottom of rails
as shown (wheels should face away from
the unit).
STEP 4. Using the 5 mm Hex Wrench
install two M8 Button Head Screws
with washers as shown. Do not tighten
completely.
STEP 5. Using the 13 mm Wrench install
the two M8 Hex Head Screws with
washers near the end cap at the base of
the unit. Do not tighten completely.
STEP 6. Using the 4 mm Hex Wrench
install four M6 Button Head Screws with
washers under the Rail Base & Handles
into the rails as shown. Do not tighten
completely.
7
STEP 7. Once all six screws have been
installed, go back and tighten each
completely.
ASSEMBLY / START
ELEVATE® PRESSTM OWNER’S GUIDE
STEP 8. Attach B to A as shown. Using
the 5 mm Hex Wrench install all eight
Short M8 screws with washers. Do not
tighten completely until all eight screws
have been installed.
8
D
STEP 9. Now that you have assembled
A and B to create D as shown in STEP
8, you will need to take D and lay it over
the top of C. Be sure to place a cloth or
packing material between the surfaces.
Place cloth or packing
materials here
Hinges
Using the 5 mm Hex Wrench, attach the
hinges on to C assembly with four Long
M8 screws and washers. Do not tighten
any completely until all four screws are
installed.
STEP 10. While one person holds the
Incline Strut up as shown, the other
person aligns the hinges to the set of
holes in the rails. Match the letters at each
hole to the corresponding letters on the
strut so that you know you are connecting
the two pieces correctly, and using the
5 mm Hex Wrench install the screws.
Do not tighten any completely until all
four screws are installed.
Placard
Plate
STEP 11. Turn the unit right-side up
and position your ELEVATE Press in a
permanent location then bolt to floor from
the Anchor Feet as shown below. BOLTS
NOT INCLUDED.
Bolt to floor from Anchor Feet
GETTING
STARTED
As a facility offering the use of a
ELEVATE Press to customers, or as
a personal user of the product, you
(as owner of the product), assume
the responsibility to become familiar
with the guidelines relative to safe use
of the product and to convey these
guidelines to all users. Read all safety,
warnings and usage instructions
before using the ELEVATE Press. Care
and maintenance for this product are
included to promote safe, enjoyable
and prolonged use of this equipment.
When using your ELEVATE Press,
wear athletic shoes and comfortable
lightweight clothing. Before you begin,
check to ensure that all parts are in
place and working properly. Remember
to control the glideboard at all times,
particularly when getting on or off your
ELEVATE Press.
WARNING
Always control the glideboard
while using your Total Gym
ELEVATE Press.
ELEVATE Press is rated at a
maximum user weight capacity
of 400 lbs [181 kg].
®
PRESSTM OWNER’S GUIDE
ROLLERS / MAINTENANCE
GLIDEBOARD:
ROLLER REMOVAL AND ASSEMBLY
STEP 1. Remove the six M6 screws
from the Rail End Caps on the top end of
the rails with a 4 mm Hex Wrench (not
included) and remove the end caps.
STEP 2. Roll the glideboard up and out
the top of the rails and set it upside down
on a clean smooth surface.
STEP 3. To remove the rollers use a 13
mm socket wrench and a 13 mm openend wrench.
Insert socket wrench over the bolt on the
outside of the roller as you engage the
open-end wrench on the nut on the inside
of the frame; turn to unscrew.
NOTE: Socket wrench and open-end
wrench not included.
Bolt
Nut
STEP 4. Replace the rollers as needed
and reinstall the bolt and nut.
Tighten just enough so that the wheel can
roll but does not slide lengthwise on the
axle. DO NOT OVER TIGHTEN.
STEP 5. Reinstall the glideboard by
carefully and slowly rolling it back into the
rails.
STEP 6. Replace the Rail End Caps on the
rails and insure all 6 screws are tight.
MAINTENANCE
AND CARE
Your ELEVATE Press unit will offer you
years of easy operation if you follow
these simple tips for maintenance
and care. With periodic cleaning,
moving parts and rolling surfaces will
maintain their smooth function. Clean
rail surfaces on a regular basis with
a noncorrosive cleaner like soap and
water or waterless cleaner or just wipe
clean with a dry towel. Some black
powder residue is normal on the inside
of the rails. All other parts can be
cleaned the same way or antibacterial
wipes may be used.
CAUTION! DO NOT USE ANY
LUBRICANTS OR SILICONE-BASED
PRODUCTS on the rails or wheels.
This will cause the wheels to slide
rather than roll and will damage the
wheels. Use a non oil–based window
cleaner on the glideboard material.
DO NOT USE ARMOR ALL® OR LIKE
SUBSTANCES. These will make the
glideboard slippery. Wipe down your
ELEVATE Press with a clean cloth.
9
MAINTENANCE SCHEDULE
DA ILY
1. Wipe down all padded surfaces with
antibacterial cleanser after each use.
2. Move the glideboard up and down
rails to ensure smooth rolling. If the
glideboard does not roll smoothly,
clean rails and wheels thoroughly with
a soft lint-free cloth.
WEEKLY
1. Wipe down rails with a non-corrosive,
no alkaline, no alcohol cleanser.
2. Clean all surface areas for aesthetics.
3. Check all screws. Fasten to ensure
they are installed correctly and
tightened.
4. Check all pads for wear and replace as
needed.
MONTHLY
1. Visually inspect the rollers. Clean any
debris accumulated on the roller.
2. Inspect rubber stoppers.
3. Replace all parts that show signs
of wear. Contact Customer Service
in USA at 858-586-6080 or email
support@totalgym.com. For
international customers, contact the
approved distributor in your country.
EXERCISE INSTRUCTIONS
ELEVATE® PRESSTM OWNER’S GUIDE
EXERCISE INSTRUCTIONS
10
Follow the instructions on the placard
as illustrated by performing the
desired number of sets and repetitions
appropriate for the skill and level of
difculty.
DECLINE PRESS-UP
STEP 1. Select appropriate incline level.
STEP 2. Kneel down on glideboard. Grasp
handles then lay down.
STEP 3. Push yourself and glideboard up
rails until arms are fully extended. Then
lower yourself back to starting position.
DECLINE PUSH-UP
STEP 1. Select appropriate incline level.
STEP 2. Lie down on glideboard. Grasp
handles.
STEP 3. Perform a push-up.
INCREASE RESISTANCE
To increase resistance, raise rails to
desired level.
DECREASE RESISTANCE
To decrease resistance, lower rails to
desired level.
1. Lift rails slightly
2. Push lever down
3. Lower to desired level
1
2
3
WARRANTY INFORMATION
®
PRESSTM OWNER’S GUIDE
WARRANTY INFO
US WARRANTY
Warranties outside the US may vary. Contact your local authorized distributor for
details.
Commercial Warranty:
• Frame – 5 years
• Rubber and Moving Parts – 1 year
• Upholstery - 90 days
LIMITED WARRANTY
IMPROPER USE OF ELEVATE PRESS: Defects or damage that result from improper
use are excluded from coverage.
UNAUTHORIZED SERVICE OR MODIFICATION: Defects or damage that result from
service, maintenance, repairs, adjustment, installation or alteration conducted by
anyone other than Total Gym or its authorized representatives are excluded from
coverage.
WARRANTY CLAIMS
Total Gym treats warranty claims as a priority. To process these quickly, a Return
Merchandise Authorization (RMA) number is required to properly link your merchandise
with your claim. Total Gym does not accept returned merchandise without an
accompanying RMA number. Contact Total Gym Customer Service Department at
858-586-6080 or email support@totalgym.com if you are making a warranty claim. A
representative will issue you an RMA number and instructions for proper packaging of
the equipment for shipping.
IMPORTANT: Save your invoice. Please retain packaging instructions. US Customer
Service Center: 858-586-6080. Shipping Damage: FOB origin, unless otherwise specied.
Total Gym accepts no responsibility for damage in shipping. Total Gym does,
however, make every effort to facilitate the satisfactory resolution of claims made
against delivery agents for damage during shipping. If the package appears to have
sustained damage in shipping, or if the equipment appears to have shifted in delivery
but no damage is evident, retain the shipping boxes until your product has been fully
assembled to ensure there is no functional damage that is not initially visible. In the
event of damage during shipping, retaining the shipping boxes helps to facilitate your
claim against the shipper. Take photographs of damaged boxes or contents before
opening.
PURCHASE RECORD. RETAIN THIS COPY FOR YOUR RECORDS.
Date Purchased ______________________________________________________________________
Purchased From ______________________________________________________________________
Model Name: ELEVATE Press, Part # 5850-B1
Serial Number ________________________________________________________________________
TotalGym.com
Customer Service:
858.586.6080
5225 Avenida Encinas Suite C
Carlsbad CA 92008
11
TotalGym.com
Customer Service: (858) 586-6080
5225 Avenida Encinas Suite C, Carlsbad CA 92008
©2017 Total Gym Global Corp. All rights reserved. Total Gym and ELEVATE are registered trademarks of TGG Global Corp. Unauthorized duplication of this booklet is punishable by law.
Covered by one or more of U.S. Pat. Nos. D574,901, 7,775,950, 8,075,457, 7,938,763, 8,834,332, D493,853, 6,921,355, 7,503,880, 7,270,628, D694347, 7,892,159, 8,702,575, 5,967,955, D734,409, D741,960, 361898, D741,420: 5,967,955; 6,921,355;
7,766,801; Australia Des. Pat. No. 154471; European Des. Pat. Nos. 000068788-0001 to 0006; New Zealand Des. Pat. No. 403803; Japan Des. Pat. No. 1203066; Russia Des. Pat. No. 56172, Taiwan Des. Pat. No. D100334; and other patents pending.
Loading...