Toshiba teli DU1207MCG, DU1207MG, DU1207MCF Instruction Manual

D4267042B

DU Series

Thank you for purchasing our product. Before using this CMOS camera, please read through this instruction manual carefully in order to use this product correctly and safely. After reading, keep this instruction manual handy so that you can refer to, whenever you need it.

CMOS Camera

Instruction Manual

Model B/W Camera : DU1207MG Color Camera : DU1207MCG / DU1207MCF

Information contained in this document is subject to change without prior notice. Standard name might be trade mark of each company.

D4267042B

Contents

Contents ................................................................................................................................................. 1

Safety Precautions ................................................................................................................................. 3

General Handing ............................................................................................................................ 4

CASES FOR INDEMNITY (LIMITED WARRANTY) ...................................................................... 6

RESTRICTION FOR USE .............................................................................................................. 7

Notes on using this product ............................................................................................................ 8

Installation ............................................................................................................................................ 12

Specifications ....................................................................................................................................... 13

Overview ....................................................................................................................................... 13

Features ........................................................................................................................................ 13

Configuration ................................................................................................................................ 15

Connection .................................................................................................................................... 16

Connector Pin Assignment ........................................................................................................... 17

Outline Drawing ............................................................................................................................ 18

General Specifications .................................................................................................................. 19

LED Status .................................................................................................................................... 22

I/O Specification ............................................................................................................................ 23

Timing Specification ...................................................................................................................... 27

Typical Spectral Response ........................................................................................................... 29

Operating Ambient Conditions ...................................................................................................... 31

Functions .............................................................................................................................................. 33

Bootstrap Registers ...................................................................................................................... 35

DeviceControl ............................................................................................................................... 37

ImageFormatControl ..................................................................................................................... 38

Scalable ........................................................................................................................................ 42

Binning .......................................................................................................................................... 47

Decimation .................................................................................................................................... 52

Reverse ........................................................................................................................................ 57

PixelFormat ................................................................................................................................... 60

BayerProcessingMode ................................................................................................................. 66

TestPattern .................................................................................................................................... 69

AcquisitionControl ......................................................................................................................... 73

ImageBuffer .................................................................................................................................. 79

TriggerControl ............................................................................................................................... 84

ExposureTime ............................................................................................................................... 94

DigitalIOControl ............................................................................................................................ 98

AntiGlitch / AntiChattering........................................................................................................... 108

TimerControl ............................................................................................................................... 112

Gain ............................................................................................................................................ 117

BlackLevel .................................................................................................................................. 120

Gamma ....................................................................................................................................... 122

Hue/Saturation ............................................................................................................................ 124

Sharpness ................................................................................................................................... 128

BalanceRatio .............................................................................................................................. 130

ColorCorrectionMatrix ................................................................................................................. 135

ALCControl ................................................................................................................................. 139

LUTControl ................................................................................................................................. 143

UserSetControl ........................................................................................................................... 146

EventControl ............................................................................................................................... 151

FrameSynchronization ................................................................................................................ 154

LEDIndicatorLuminance ............................................................................................................. 156

DPCControl ................................................................................................................................. 158

Chunk.......................................................................................................................................... 162

SequentialShutterControl ........................................................................................................... 168

Appendix ............................................................................................................................................ 173

1 / 179

D4267042B

UserSetSave and UserSetQuickSave difference ....................................................................... 173

MultiFrame and Bulk function difference .................................................................................... 175

Warranty rules .................................................................................................................................... 178

Repair ................................................................................................................................................. 179

2 / 179

D4267042B

Safety Signs

Description

WARNING

Indicates a potentially hazardous situation that may result in death or serious injury (*1) in the event of improper handling.

CAUTION

Indicates a potentially hazardous situation that may result in light to moderate injuries (*2) or only in property damage (*3)in the event of improper handling.

Safety Symbols

Description

PROHIBITED

This sign indicates PROHIBITION (Do not). The content of prohibition is shown by a picture or words beside the symbol.

MANDATORY

This sign indicates MANDATORY ACTION (You are required to do). The content of action is shown by a picture or words beside the symbol.

Safety Precautions

Before using this product, read these safety precautions carefully. Important information is shown in this Instruction Manual to protect users from bodily injuries and property damages, and to enable them to use the product safely and correctly. Please be sure to thoroughly understand the meanings of the following signs and symbols before reading the main text that follow, and observe the instructions given herein.

[Definition of Safety Signs]

Notes *1:“Serious injury” refers to cases of loss of eyesight, wounds, burns (high or low temperature),

electric shock, broken bones, poisoning, etc., which leave after-effects or which require hospitalization or a long period of outpatient treatment of cure.

*2: "Light to moderate injuries" refers to injuries, burns, electric shock etc. that do not require

hospitalization or long-term treatment.

*3: "Property damage" refers to cases of extensive damage involving damage to buildings,

equipment, farm animals, pet animals and other belongings.

[Explanation of Safety Symbols]

3 / 179

D4267042B

WARNING

 Stop operation immediately when any abnormality or defect occurs.

If abnormal conditions are present, such as smoke, a burning smell, ingress of water or foreign matter, or if the equipment is dropped or malfunctions, fire or electric shock may result. Be always sure to disconnect the power cable from the wall socket at once and contact your dealer.

Unplug

 Do not use the equipment in locations subject to water splashes.

Otherwise, fire or electric shock may result.

Do not get wet

 Do not disassemble, repair, or modify the equipment.

Otherwise, fire or electric shock may result. For internal repair, inspection, or cleaning, contact your sales representative.

Never pull apart

 Do not place anything on the equipment.

If metallic objects, liquid, or other foreign matter enters the equipment, fire or electric shock may result.

Avoid

 Do not install the equipment in an unstable or inclined location or locations

subject to vibration or impact.

Otherwise, the equipment may topple over and cause personal injury.

Avoid

 During an electrical storm, do not touch the power cable and the connection

cable.

Otherwise, an electric shock may result.

Do not touch

Instruction

 Use the specified voltage.

Use of an unspecified voltage may result in fire or electric shock.

 Do not be handled roughly, damaged, fabricated, bent forcefully, pulled, twisted,

bundled, placed under heavy objects or heated the power cable and the connection cable.

Otherwise, fire or electric shock may result.

Avoid

General Handing

4 / 179

D4267042B

CAUTION

 Observe the following when installing the equipment:

·Do not cover the equipment with a cloth, etc.

·Do not place the equipment in a narrow location where heat is likely to accumulate. Otherwise, heat will accumulate inside the equipment, possibly resulting in a fire.

Instruction

 Do not place the equipment in locations subject to high moisture, oil fumes,

steam, or dust.

Otherwise, fire or electric shock may result.

Avoid

 Do not install the equipment in locations exposed to direct sunlight or humidity.

Otherwise, the internal temperature of the equipment will rise, which may cause a fire.

Avoid

 Use only specified the power cable and the connection cables.

Otherwise, fire or electric shock may result.

Instruction

 Do not give strong impact against the equipment.

It may cause the trouble.

Avoid

 When performing connection, turn off power.

When connecting the power cable and the connection cable, turn off the equipment power. Otherwise, fire or electric shock may result.

Instruction

 Do not expose its camera head to any intensive light (such as direct sunlight).

Otherwise, its inner image pickup device might get damaged.

Avoid

 Avoid short-circuiting signal output.

Otherwise, a malfunction may occur.

Avoid

 Avoid giving a strong shock against the camera body.

It might cause a breakdown or damage. If your camera is used in a system where its connector is subjected to strong repetitive shocks, its connector is possible to break down. If you intend to use your camera in such a situation, if possible, bundle and fix a cable in the place near the camera, and do not transmit a shock to the connector.

Avoid

 Contact your sales representative to request periodic inspection and cleaning

(every approx five years).

Accumulation of dust inside the equipment may result in fire or electric shock. For inspection and cleaning costs, contact your sales representative.

Instruction

5 / 179

D4267042B

CASES FOR INDEMNITY (LIMITED WARRANTY)

We shall be exempted from taking responsibility and held harmless for damage or losses incurred by the user in the following cases.

● In the case damage or losses are caused by natural disasters, such as an earthquake and thunder, fire, or other acts of God, acts by a third party, deliberate or accidental misuse by the user, or use under extreme operating conditions.

● In the case of indirect, additional, consequential damages (loss of business interests, suspension of business activities) are incurred as result of malfunction or non-function of the equipment, we shall be exempted from responsibility for such damages.

● In the case damage or losses are caused by failure to observe the information contained in the instructions in this instruction manual and specifications.

● In the case damage or losses are caused by use contrary to the instructions in this instruction manual and specifications.

● In the case damage or losses are caused by malfunction or other problems resulting from unintended use of equipment or software etc. that are not specified.

● In the case damage or losses are caused by repair or modification conducted by the customer or any unauthorized third party (such as an unauthorized service representative).

● Expenses we bear on this product shall be limited to the individual price of the product.

● The item that is not described in specifications of this product is out of the guarantee.

● The case of damages or losses which are caused by incorrect connection of the cable is out of the

guarantee.

6 / 179

D4267042B

RESTRICTION FOR USE

● Should the equipment be used in the following conditions or environments, give consideration to safety measures and inform us of such usage:

1. Use of the equipment in the conditions or environment contrary to those specified, or use outdoors.

2. Use of the equipment in applications expected to cause potential hazard to people or property, which require special safety measures to be adopted.

● This product can be used under diverse operating conditions. Determination of applicability of equipment or devices concerned shall be determined after analysis or testing as necessary by the designer of such equipment or devices, or personnel related to the specifications. Such designer or personnel shall assure the performance and safety of the equipment or devices.

● This product is not designed or manufactured to be used for control of equipment directly concerned with human life (*1) or equipment relating to maintenance of public services/functions involving factors of safety (*2). Therefore, the product shall not be used for such applications.

(*1): Equipment directly concerned with human life refers to.

- Medical equipment such as life-support systems, equipment for operating theaters.

- Exhaust control equipment for exhaust gases such as toxic fumes or smoke.

- Equipment mandatory to be installed by various laws and regulations such as the Fire Act or Building Standard Law

- Equipment related to the above

(*2): Equipment relating to maintenance of public services/functions involving factors of safety refers to.

- Traffic control systems for air transportation, railways, roads, or marine transportation

- Equipment for nuclear power generation

- Equipment related to the above

7 / 179

D4267042B

10mm or less

C-mount lens

Bottom of the screw

8mm or less

Notes on using this product

● Handle carefully Do not drop the equipment or allow it to be subject to strong impact or vibration, as such action may cause malfunctions. Further, do not damage the connection cable, since this may cause wire breakage.

● Environmental operating conditions Do not use the product in locations where the ambient temperature or humidity exceeds the specifications. Otherwise, image quality may be degraded or internal components may be adversely affected. In particular, do not use the product in areas exposed to direct sunlight. Moreover, during shooting under high temperatures, vertical stripes or white spots (noise) may be produced, depending on the subject or camera conditions (such as increased gain). However, such phenomena are not malfunctions.

● Check a combination with the lens Depending on the lens and lighting you use, an image is reflected as a ghost in the imaging area. However, this is not because of a fault of the camera. In addition, depending on the lens you use, the performance of the camera may not be brought out fully due to deterioration in resolution and brightness in the peripheral area, aberration and others. Be sure to check a combination with the camera by using the lens and lightning you actually use. When installing a lens in the camera, make sure carefully that it is not tilted. In addition, use a mounting screw free from defects and dirt. Otherwise, the camera may be unable to be removed. Install a next lens; its dimension of protrusion from bottom of the screw is equal to or less than 8 mm. If a lens does not stand to this condition, it might not be installed to this camera.

● Mounting to pedestal

When mounting this product to a pedestal, make sure carefully that lens doesn’t touch with the pedestal.

8 / 179

D4267042B

● Do not expose the camera's image-pickup-plane to sunlight or other intense light directly Its inner CMOS sensor might be damaged.

● Occurrence of moiré If you shoot thin stripe patterns, moiré patterns (interference fringes) may appear. This is not a malfunction.

● Occurrence of noise on the screen If an intense magnetic or electromagnetic field is generated near the camera or connection cable, noise may be generated on the screen. If this occurs, move the camera or the cable.

● Handling of the protective cap If the camera is not in use, attach the lens cap to the camera to protect the image pickup surface.

● If the equipment is not to be used for a long duration Turn off power to the camera for safety.

● Maintenance Turn off power to the equipment and wipe it with a dry cloth. If it becomes severely contaminated, gently wipe the affected areas with a soft cloth dampened with diluted neutral detergent. Never use alcohol, benzene, thinner, or other chemicals because such chemicals may damage or discolor the paint and indications. If the image pickup surface becomes dusty, contaminated, or scratched, consult your sales representative.

9 / 179

D4267042B

Following information is only for EU-member states:

The use of the symbol indicates that this product may not be treated as household waste. By

ensuring this product is disposed of correctly, you will help prevent potential negative

consequences for the environment and human health, which could otherwise be caused by

inappropriate waste handling of this product. For more detailed information about the take-back

and recycling of this product, please contact your supplier where you purchased the product.

“This symbol is applicable for EU member states only”

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communication. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

 Defective pixels

A CMOS image sensor is composed of photo sensor pixels in a square grid array. Due to the characteristics of CMOS image sensors, over- or under-driving of the pixels results in temporary white or black areas (as if these are noises) appearing on the screen. This phenomenon which is not a defect is exacerbated under higher temperatures and long exposure time.

 Image shading

The brightness of the upper part of the screen may be different from that of the lower part. Note that this is a characteristic of a CMOS image sensor and is not a fault.

● Disposal When disposing of the camera, it may be necessary to disassemble it into separate parts, in accordance with the laws and regulations of your country and/or municipality concerning environmental contamination.

[Phenomena specific to CMOS sensor]

10 / 179

D4267042B

环保使用期限标识，是根据电子信息产品污染控制管理办法以及，电子信息产品污染控制标识要求(SJ/T11364-2014)、电子信息产品环保使用期限通则，制定的适用于中国境内销售的电子信息产品的标识。电子信息产品只要按照安全及使用说明内容，正常使用情况下，从生产月期算起，在此期限内，产品中含有的有毒有害物质不致发生外泄或突变，不致对环境造成严重污染或对其人身、财产造成严重损害。产品正常使用后，要废弃在环保使用年限内或者刚到年限的产品时，请根据国家标准采取适当的方法进行处置。另外，此期限不同于质量/功能的保证期限。

The Mark and Information are applicable for People's Republic of China only.

部件名称

有毒有害物质或元素

铅（Pb）

汞（Hg）

镉（Cd）

六价铬

（Cr(VI)）

多溴联苯

（PBB）

多溴二苯醚

(PBDE）

相机本体

× ○ ○ ○ ○

○

本表格依据SJ/T 11364的规定编制 ○：表示该有毒有害物质在该部件所有均质材料中的含量均在电子信息产品中有毒有害物质的

限量要求标准规定的限量要求(GB/T26572)以下

×：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出电子信息产品中有毒有害

物质的限量要求标准规定的限量要求(GB/T26572)

This information is applicable for People's Republic of China only.

中华人民共和国

环保使用期限

ペーパーボード

纸板

Paper board

箱／箱子／Box

内部緩衝材料・袋内部缓冲材料·袋

Internal buffer materials・Bag

10

＜产品中有毒有害物质或元素的名称及含量＞

リサイクルに関する情報（包装物）

有关再利用的信息(包装物)

Information on recycling of wrapping composition

11 / 179

D4267042B

Installation

Before using this product, you shall install application software to display image and control registers of camera, and IP configuration tool for network setting. You can download the SDK for our USB camera products (TeliCamSDK) from the Service & Support section of our website. User registration is necessary to use downloading service. Please make a user registration, or contact your sales representative.

● TOSHIBA TELI CORPORATION Top Page

http://www.toshiba-teli.co.jp/en/

● Service & Support

https://www.toshiba-teli.co.jp/cgi/ss/en/service.cgi

Please refer to the TeliCamSDK startup guide, about Operation environment, Installation, and Setup.

12 / 179

D4267042B

Specifications

Overview

DU1207M series is an integrated-(one-body)-type camera that adopts a global shutter CMOS sensor. These are DU1207MG (12M type1.1). Suffix [C] are attached to the color models. For video output and camera control, the USB 3.0 interface standard is adopted for high transfer rate, and it is easy to integrate into industrial equipment.

Features

● High frame rate Supporting high frame rate, DU1207MG 32fps (Mono8), DU1207MCG/MCF 31fps (Bayer8).

● Global shutter As it employs a global electronic shutter similar to a CCD image sensor, clear images of even fast-moving object are obtainable with less blur.

● USB*3.0 interface Video output and camera control are performed via the USB 3.0 standard interface. Data transfer is up to 5Gbps (Maximum) that enables to output uncompressed video data at high frame rate.

● USB3 Vision* This product is based on USB3 Vision Ver.1.0.

● GenICam* Ver 2.3 This product is based on GenICam Generic Interface for Cameras Ver 2.3.

● IIDC2* Digital Camera Control Specification Ver.1.1.0

This product is based on IIDC2 Digital Camera Control Specification Ver.1.1.0.

13 / 179

D4267042B

● e-CON* Connector adoption

The e-CON connector adoption enables to assemble the cable easily without using special tools.

● Random Trigger Shutter The Random Trigger Shutter function provides images in any timing by input of an external trigger signal. Trigger control from PC is available as well.

● Scalable Selectable video output area. This mode achieves higher frame rate by reducing vertical output area. And reduces occupied data rate of USB bus by reducing horizontal output area.

● Binning Pixel data is combined by vertical and horizontal. It achieves high frame rate.

● Decimation Camera reads all effective areas at high speed by skipping lines.

● Color processing Color models have built in color processing. There are RGB, BGR, YUV 4:2:2, YUV 4:1:1, Bayer and Mono output modes. In addition, it produced an image with restrained false color by adaptive filter interpolating 7 x 7 pixels.

●Dust-proof Glass Dust-proof Glass is built in default. Suffix [G] is attached to the model name of built-in Glass.

● IR-cut filter Build-in IR-cut filter models are optional for color models. Suffix [F] is attached to the model name of built-in IR-cut filter model.

● EU RoHS & Chinese ROHS

* USB is a unified standard established by USB-IF(USB Implementers Forum). * USB3 Vision is a unified standard established by AIA (Automated Imaging Association). * GeniCam is a registered trademark of EMVA (European Machine Vision Association). * IIDC2 is a unified standard established by JIIA (Japan Industrial Association). * e-CON (Easy & Economy connector) is a sensor connector that is normalized by the manufacturer of the

sensor, FA equipment and connector.

14 / 179

D4267042B

Configuration

The system configuration of this camera series is as follows; This camera has no accessories, please prepare other equipment separately.

● Camera: This product.

● Camera mounting kit CPTC6M (*1): To fix a camera to a tripod; attach this to the bottom of the camera.

● USB3.0 Cable (*2): This cable is used to connect the camera to host PC. Please use

a USB3.0 cable of Standard A - Micro B. This product is able to connect a USB cable equipped with screw lock mechanism. Please use it as needed.

● USB3.0 Interface Card (*2): This is the interface card to connect to the camera. Usually this

card is installed to expansion slot of PC etc.

● e-CON Cable. (*2): This cable is used to input external trigger signal and output GPIO

signal. We recommend using shielded cable, because there is likely to be affected by the noise depending on the operating environment of the camera.

*1: Optional part. Contact your sales representative for details of option units. *2: Commercial items.

15 / 179

D4267042B

Camera

Host(PC etc.)

Camera mounting unit

CPTBU

Interface Card

Stream Packet →← Control Packet

USB3.0 Cable

(Mirco B) (Standard A)

1. Line2

2. Line1

3. GND

4. Line0

(e-CON)

e-CON Cable

Notes on Connection:

- Please confirm the power supply of the camera off when plugging in or pulling out the I/O Connector. It causes the breakdown.

- If your camera is used in a system where its connectors are subjected to strong repetitive shocks, its connectors are possible to break down. If you use your camera in such a situation, use an USB3.0 cable with a lock screw, and secure the camera cable as close as possible to the camera body for avoid physical shock to the camera connector.

- About e-CON cable: In the case that electric-wire is long or thin, input and output voltage may not satisfy specifications of the camera or your system by voltage drop. Please confirm wires’ specifications before use them.

- Los t packets may occur by an electrical characteristic of the transmission line of USB3.0. (USB3.0 Interface Card,

USB3.0 Cable, and USB3.0 HUB).

CPTC6M

Connection

16 / 179

D4267042B

①

②

1. USB3.0 Interface Connector Connector model: WMUR-10F6L1PH5N (WIN WIN PRECISION INDUSTRIAL)

Pin No.

I/O

Signal

Function

1 -

VBUS

Power

2 I/O

D-

USB2.0 differential pair

3 I/O

D+

4 -

NC

Not connected

5 -

GND

Ground for power return

6 O

SSTX-

SuperSpeed transmitter differential pair

7 O

SSTX+

8 -

GND_DRAIN

Ground for SuperSpeed signal return

9 I

SSRX-

SuperSpeed receiver differential pair

10 I SSRX+

2. I/O Connector Connector (Camera side) 37204-62B3-004PL (Sumitomo 3M) or equivalent

Matching connector (Cable side) Connectors which conformed to e-CON

e.g. 37104 series (Sumitomo 3M), RITS 4P series (Tyco) * Matching connector is not an accessory of this product. Pin assignment

↑TOP

*Above figure is connector view from insert side.

Pin No.

I/O

Signal

Function

1 I/O

Line2

GPIO Input / Output

2 O

Line1

GPIO Output

3 -

GND

Ground

4 I

Line0

GPIO Input

1 2 3 4

Connector Pin Assignment

Rear View

17 / 179

D4267042B

Outline Drawing

18 / 179

D4267042B

Model Name

DU1207MG

Optical part

Optical glass

Imager

CMOS image sensor

Number of Video out pixels (H) × (V)

4096 x 3000

Optical Size

type1.1

Scanning area (H) × (V)[mm]

14.19 x 10.34

Pixel size (H) × (V)[μm]

3.45 ×3.45

Scan method

Progressive

Electronic shutter method

Global shutter

Aspect ratio

4 : 3

Sensitivity

860lx, F5.6, 1/32s

Minimum illuminance

2lx (F1.4, Gain +24dB, Video Level 50%)

Power supply

DC +5V5% (from USB connector)

Power consumption (*1)

4.0W (maximum)

Interface

USB 3.0 (Only SuperSpeed is supported)

Transmission speed

5Gbps (maximum)

Protocol

USB3 Vision

Image format

Mono8, Mono10, Mono12

Maximum Frame rate (*2)

Mono8

32 fps

Mono10, Mono12

16 fps

Dimensions

40 mm(W) x 40 mm (H) x 35 mm (D) (Not including protrusion)

Mass

90g

Lens mount

C-mount

Flange back

17.526mm

Camera body grounding: insulation status

Conductive between circuit GND and camera body

General Specifications

● B/W model

*1, *2 at the all pixel readout

19 / 179

D4267042B

Model Name

DU1207MCG

DU1207MCF

Optical Part

Optical glass

IR cut filter

Imager

CMOS image sensor

Number of Video out pixels (H) × (V)

4096 x 3000

Optical Size

Type 1.1

Scanning area (H) × (V)[mm]

14.19 x 10.34

Pixel size (H) × (V)[μm]

3.45 ×3.45

Scan method

Progressive

Electronic shutter method

Global shutter

Aspect ratio

4 : 3

Sensitivity

1150lx, F5.6, 1/31s

1425lx, F5.6, 1/31s

Minimum illuminance

3lx (F1.4, Gain +24dB, Video Level 50%)

Power supply

DC +5V5% (from USB connector)

Power consumption (*1)

4.5W (maximum)

Interface

USB 3.0 (Only SuperSpeed is supported)

Transmission speed

5Gbps (maximum)

Protocol

USB3 Vision

Image format

RGB, BGR, YUV422, YUV411, Bayer8, Bayer10, Bayer12, Mono8

Maximum Frame rate (*2)

Bayer8, Mono8

31 fps

YUV411

21 fps

YUV422

16 fps

Bayer10, Bayer12

16 fps

RGB, BGR

10 fps

Dimensions

40 mm(W) x 40 mm (H) x 35 mm (D) (Not including protrusion)

Mass

90g

Lens mount

C-mount

Flange back

17.526mm

Camera body grounding: insulation status

Conductive between circuit GND and camera body

● Color model

*1, *2 at the all pixel readout

20 / 179

D4267042B

Notes on combination of C-mount lens:

- Depending on the lens you use, the performance of the camera may not be brought out fully due to the deterioration in resolution and brightness in the peripheral area, occurrence of a ghost, aberration and others. When you check the combination between the lens and camera, be sure to use the lens you actually use.

- In addition, use a mounting screw free from defects and dirt. Otherwise, the camera may be unable to be removed.

- As for the C-mount lens used combining this camera, the projection distance from bottom of the screw should use 8mm or less.

10mm or less

C-mount lens

Bottom of the screw

8mm or less

21 / 179

D4267042B

Camera state

Lamp indication

No power

Off

Link detection in progress

Fast flash green (ON:20ms, OFF:60ms)

Connection Error

Flash alternate red / green

SuperSpeed connected, but no data being transferred

Flash green (ON: 200ms, OFF: 800ms)

SuperSpeed connected, waiting for trigger

Flash orange (ON: 200ms, OFF: 800ms)

Data being transferred

Fast flash green (ON:60ms, OFF:20ms)

Error during data transfer

Solid Red (Time period: 500ms)

Stand-by

Super slow flash orange (ON:200ms, OFF: 2800ms)

LED Status

22 / 179

D4267042B

Inside

DC3.3V

0V

10kΩ

Notes of external trigger signal:

Depending on cable length, cable kinds and input current of trigger input line, Random Trigger Shutter operation may not satisfy timing specification or camera may not receive EXT_TRIG signal. Please confirm it before use.

Notes of input level:

Line0 and Line2 have different input level. Please use input level within the voltage described in this specification.

I/O Specification

● Signal Specification

- Line0 (GPIO Input, I/O connector : 4 pin) Input Circuit : LVTTL Level : Low 0 ~ 0.5V, High 2.0 ~ 24.0V Polarity : High active / Low active (initial factory setting: Low active) Pulse Width : Minimum 50μs Input circuit diagram

23 / 179

D4267042B

● External trigger input recommended circuit

CAMERA Inside

DC3.3V

10kΩ

4

3

Photocoupler

Camera

GND

Your GND

Your system

Your

Secondary GND

Your GND

Your system

Your

FRAME GND

DC3.3V

10kΩ

4

3

Camera

GND

CAMERA Inside

Notes of trigger input cable:

- The recognition of the trigger signal depends on the length, characteristic or driving current of the cable. Therefore please confirm your system about those conditions.

- Pin 3 is conducted with camera frame.

Using shield cable, terminal processing of the shield is referred as above.

- Please confirm the EMC adaptability in whole of your system.

- Isolated I/F

- Non-Isolated I/F

24 / 179

D4267042B

- Line2 (GPIO Input / Output, initial factory setting: Input, I/O connector : 1 pin)

Inside

DC5.0V

10kΩ

1

3

IOLineModeAll

Notes of external trigger signal:

Depending on cable length, cable kinds and input current of trigger input line, Random Trigger Shutter operation may not satisfy timing specification or camera may not receive EXT_TRIG signal. Please confirm it before use.

Notes of input level:

Line0 and Line2 have different input level. Please use input level within the voltage described in this specification.

- Input signal specification Level : Low 0 ~ 0.5V, High 4.0 ~ 5.0V Polarity : High active / Low active (initial factory setting: Low active) Pulse Width : Minimum 50μs

- Output signal specification Output Circuit : 5V CMOS Maximum Current : +/-32mA Polarity : High active / Low active (initial factory setting: Low active) Signal Source : TIMER0 ACTIVE

USER OUTPUT EXPOSURE ACTIVE FRAME ACTIVE FRAME TRANSFER FRAME TRIGGER WAIT

Input / Output circuit diagram

25 / 179

D4267042B

- Line1 (GPIO Output, I/O connector : 2 pin) Output Circuit : 5V CMOS Maximum Current : +/-32mA Polarity : High active / Low active (initial factory setting: Low active) Signal Source : TIMER0 ACTIVE

USER OUTPUT EXPOSURE ACTIVE FRAME ACTIVE FRAME TRANSFER FRAME TRIGGER WAIT

26 / 179

D4267042B

T1

Sensor Output

Exposure

Image Image

T3

T2

Image Image

USB Streaming

Model Name

format

T1

[ms]

T2

[ms]

T3 [s]

DU1207MG

Mono8

15.8

30.85

1/(Frame Rate setting)

Mono10, Mono12

22.0

61.83

DU1207MCG/CF

Bayer8, Mono8

15.8

30.85

YUV 4:1:1

22.0

46.28

YUV 4:2:2

61.83

Bayer10, Bayer12

61.83

RGB, BGR

92.57

Timing Specification

Image data outputs are transferred with USB bulk transfer. Timing numerical value below is described by absolute prerequisite that camera can use transmission band without restriction of other device. When there is other device on the same bus, the value described below is not guaranteed.

● In Manual Shutter mode

27 / 179

D4267042B

Image

USB Streaming

Exposure

TRIG_IN

T4

T2

Image

USB Streaming

Exposure

TRIG_IN

T4

T2

T5

Model Name

format

T4

[μs]

T5

[μs]

DU1207MG

Mono8

16.1

30.4

Mono10, Mono12

22.3

36.6

DU1207MCG/CF

Bayer8, Mono8

16.1

30.4

YUV 4:1:1

22.3

36.6

YUV 4:2:2

Bayer10, Bayer12

RGB, BGR

Notes of random trigger shutter mode:

- In the period when FRAME_TRIGGER_WAIT (GPIO signal) is inactive, user must not input external trigger signal to this camera.

- When the interval of the input trigger signal is extremely short, or when the trigger signal is noisy, there is a possibility

of causing the malfunction. In this case, please input a proper trigger signal.

● In Random Trigger Shutter mode

Edge mode / Bulk mode (at all pixels readout)

Level mode (at all pixels readout)

* The value of T2 is the same as the value of normal shutter mode. * T4 and T5 are typical value. * In case that the Trigger mode is Level mode, exposure time is 14.26μs longer than trigger signal width due

to the CMOS sensor specifications.

28 / 179

D4267042B

Typical Spectral Response

* The lens characteristics and light source characteristics is not reflected in table.

● DU1207MG

29 / 179

Toshiba teli DU1207MCG, DU1207MG, DU1207MCF Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual