Toshiba ZH36 Series, ZH37 Series Owner's Manual
ZH36/37 Series
TOSHIBA
Colour television
Owner’s manual
2
SETTING UP
Safety precautions – Some do’s and don’ts for you to be aware of 3
The remote control – an at-a-glance guide 4
Connecting external equipment 5
Front connections and controls 6
Selecting the language, country and system, Auto tune 7
Manual tune – an alternative to Auto tuning 8
Programme skip 9
Manual fine tuning, Sorting programme positions 10
CONTROLS
General controls – changing programme position 11
Sound controls – volume, sound mute, bass/treble/balance, volume correction, dynamic sub bass 11
Widescreen viewing 12
Picture controls – picture preferences, noise reduction, black stretch, picture position, automatic format (widescreen), still picture 13
FEATURES
Virtual Dolby Surround
(ZH37 models only)
14
The timer and time display – setting the TV to turn off and time display 15
Panel lock – disabling the buttons on the TV 15
Stereo and bilingual transmissions – stereo or dual language broadcasts 15
Input selection and AV connections – input and output sockets for connected equipment 16
TELETEXT
Setting up, general information, Auto and List modes 17
Control buttons 18
PROBLEM SOLVING
Questions and Answers 19
INFORMATION
Index, Specifications and Accessories – information on your television 20
?
For television
operation queries,
please ring the
helpline…
Remember…
For UK only
Contents
If stationary images generated by TELETEXT, CHANNEL IDENTIFICATION LOGOS, COMPUTER DISPLAYS, VIDEO GAMES, ON
SCREEN MENUS, etc. are left on the TV screen for any length of time, they could become permanently ingrained.
If you use your television to display completely still images, or moving pictures which have a permanent still image superimposed
e.g. broadcast network logos, it is always advisable to reduce BOTH the brightness and contrast settings.
WARNING! NEVER LEAVE A STATIONARY IMAGE ON THE SCREEN
Please take note
EXCLUSION CLAUSE
Toshiba shall under no circumstances be liable for loss and/or damage to the product caused by:
i) fire;
ii) earthquake;
iii) accidental damage;
iv) intentional misuse of the product;
v) use of the product in improper conditions;
vi) loss and/or damge caused to the product whilst in the possession of a third party;
vii) any damage or loss caused as a result of the owner’s failure and/or neglect to follow the instructions set out in the owner’s
manual;
viii) any loss or damage caused directly as a result of misuse or malfunction of the product when used simultaneously with
associated equipment;
Furthermore, under no circumstances shall Toshiba be liable for any consequential loss and/or damage including but not limited
to the following, loss of profit, interruption of business, the loss of recorded data whether caused during normal operation or
misuse of the product.
3
Safety Precautions
This equipment has been designed and manufactured to meet international safety standards but, like any
electrical equipment, care must be taken to obtain the best results and for safety to be assured. Please read
the points below for your own safety. They are of a general nature, intended to help with all electronic
consumer products and some points may not apply to the goods you have just purchased.
DON'T remove any fixed cover as this may expose
dangerous voltages.
DON'T obstruct the ventilation openings of the
equipment with items such as newspapers,
tablecloths, curtains, etc. Overheating will cause
damage and shorten the life of the equipment.
DON'T allow electrical equipment to be exposed to
dripping or splashing or objects filled with liquids,
such as vases, to be placed on the equipment.
DON’T place hot objects or naked flame sources,
such as lighted candles or nightlights on, or close to
equipment. High temperatures can melt plastic and
lead to fires.
DON'T use makeshift stands and NEVER fix legs
with wood screws. To ensure complete safety,
always fit the manufacturer’s approved stand or
legs with the fixings provided according to the
instructions.
DON'T listen to headphones at high volume, as
such use can permanently damage your hearing.
DON'T leave equipment switched on when it is
unattended, unless it is specifically stated that it is
designed for unattended operation or has a
standby mode. Switch off using the switch on the
equipment and make sure your family know how to
do this. Special arrangements may need to be
made for infirm or handicapped people.
DON'T continue to operate the equipment if you
are in any doubt about it working normally, or it is
damaged in any way – switch off, withdraw the
mains plug and consult your dealer.
ABOVE ALL – NEVER let anyone, especially
children, push anything into holes, slots or any
other openings in the case – this could result
in a fatal electric shock.
NEVER guess or take chances with electrical
equipment of any kind – it is better to be safe
than sorry.
TO FULLY DISCONNECT THE TV, SWITCH OFF
THE MAINS SOCKET AND REMOVE THE
POWER PLUG.
Leave at least 10cm clearance around the television
to allow adequate ventilation. This will prevent
overheating and possible damage to the TV. Dusty
places should also be avoided.
Damage may occur if the TV is left in direct sunlight
or near a heater. Avoid places subject to extremely
high temperatures or humidity, or locations where the
temperature is likely to fall below 5°C (41°F).
The mains supply required for this equipment is
230v AC 50Hz. Never connect to a DC supply or
any other power source. DO ensure that the TV is
not standing on the mains lead. DO NOT cut off
the mains plug from this equipment, this
incorporates a special Radio Interference Filter, the
removal of which will impair its performance. In the
UK, the fuse fitted in this plug is 13A, and is
approved by ASTA or BSI to BS1362. It should only
be replaced by a correctly rated and approved type
and the fuse cover must be refitted.
IF IN DOUBT PLEASE CONSULT A COMPETENT
ELECTRICIAN.
DO read the operating instructions before you
attempt to use the equipment.
DO ensure that all electrical connections (including
the mains plug, extension leads and interconnections between pieces of equipment) are
properly made and in accordance with the
manufacturers’ instructions. Switch off and withdraw
the mains plug before making or changing
connections.
DO consult your dealer if you are ever in doubt
about the installation, operation or safety of your
equipment.
DO be careful with glass panels or doors
on equipment.
Air Circulation
Do not
Heat Damage
Mains Supply
Do
4
The remote control
UP
Remove the back cover to reveal the battery compartment and make sure the batteries are inserted
the right way round.
Suitable battery types for this remote are UM-4, AAA, IEC R03 1.5V.
Do not combine a used, old battery with a new one or mix battery types. Dispose of them in a
designated disposal area.
The performance of the remote control will deteriorate beyond a distance of five metres or outside an
angle of 30 degrees from the centre of the TV.
Inserting batteries and effective range of the remote
Simple at-a-glance reference of your remote control.
For quick reference to
topics, please see
the
INDEX
at the end of
this manual.
To mute the sound
Teletext control buttons
To exit Menus
Dynamic Sub Bass
Virtual Dolby Surround
(ZH37 models only)
To bring up on-screen information and
for the teletext initial/index function
To select input from external sources
To access sub-pages when in teletext
mode
To select mode
On-screen Menus
Selectable picture preferences
Widescreen viewing
Number buttons
To return to the previous programme
For On/Standby mode
To display teletext
When in VCR or DVD mode:
press
m
to PAUSE
press
w
to EJECT
press
l
q
to SKIP-REWIND
press
s
l
to SKIP-FORWARD
press
r
to PLAY
press
p
to STOP
press
q
to REWIND
press
s
to FAST FORWARD
☛
To change programme positions and
teletext pages
To alter the volume
When using menus the arrows move the
cursor on the screen up, down, left or
right. OK to confirm your selection
When in TV mode:
u
Still picture
O
I/II Stereo/bilingual reception
8/9
Time display
When in Teletext mode:
r
To reveal concealed text
q
To hold a wanted page
s
To enlarge teletext display size
8/9
To select a page whilst viewing a
normal picture
5
Connecting external equipment
Before connecting any external equipment, turn off all main power switches.
IN
OUT
IN
OUT
the back of your TV
video recorder
decoder*
SATIN/OUT
VCR
TV
SCART 2 (EXT2)
SCART 1 (EXT1)
A wide variety of external equipment can be
connected to the back of the TV, therefore the
relevant owners manuals for all additional
equipment must be referred to.
We recommend Scart 1 for a decoder, Scart 2 for a
VCR and Input 3 for additional equipment.
If connecting S-VIDEO equipment, set the INPUT for
EXT2. See page 16.
If the TV automatically switches over to monitor
external equipment, return to normal TV by pressing
the desired programme position button.
To recall external equipment, press Bto select
between EXT1, EXT2 and EXT3.
WE RECOMMEND THAT YOU USE SCART LEADS IN
ADDITION TO AERIAL CABLES WHEREVER
POSSIBLE
Aerial cables:
Connect the aerial to the socket on the rear of the
television. If you use a decoder* and/or a video
recorder it is essential that the aerial cable is connected
through the decoder and/or through the video
recorder to the television.
Scart leads:
Connect the video recorder IN/OUT socket to the TV.
Connect the decoder TV socket to the TV. Connect the
video recorder SAT socket to the decoder VCR socket.
Before running Auto tuning put your decoder and
video recorder to Standby.
*
a decoder could
be Digital Satellite or
any other compatible
decoder.
☛
6
Front connections and controls
If the power-on light is unlit press the POWER button on
the front of the TV to switch the set on, then press a
number button on the remote control to see the screen.
To put the set into Standby press ion the remote
control. To view the TV press iagain or any of the
number buttons. The picture may take a few seconds to
appear. Standby should only be used for short periods of
time.
To set up the TV you will now need to use the on-screen
menus. Press the MENU button on the remote control to
see the top menu bar.
This white menu bar will show five different topics shown
in symbols. As each symbol is selected by pressing the
S
or Rbutton on the remote control, its respective
options will appear below.
To use the options press the Q button on the remote
control to move down through them and Sor Rto select
the required choice. Follow the on screen instructions.
The functions of each menu are described in detail
throughout the manual.
A wide variety of external equipment can be connected via the sockets located behind the flap on the TV.
Press the centre of the flap to open it.
Whilst all the necessary adjustments and controls for the TV are made using the remote control, the buttons on
the TV may be used for some functions.
Power Button
RED – Power On
GREEN – On timer is set
To alter the volume press — j +.
To alter the programme position press
eeFff
.
Press MENU and S,R, Q or P to control the sound
and picture options.
Press MENU to finish.
Before connecting any external equipment, turn off
all main power switches.
When connecting mono sound equipment to Input 3,
connect the audio output of the equipment to the
L/Mono socket onthe TV.
To select the Inputs, press Buntil the display shows
EXT3 as described on page 16.
Please always refer to the owner’s manual of the
equipment to be connected for full details.
Please note: Inserting the headphone jack will mute the
sound from all speakers.
Switching on Using the controls and connections
Loading...