Toshiba TLP-X100U, TLP-WX100, TLP-WX100U - TLP WX100 WXGA LCD Projector, TLP-X100 Owner's Manual
Before UsingPreparationsOperationsMaintenanceOthers
TLP-X100
(XGA)
TLP-WX100
(WXGA)
DATA PROJECTOR
OWNER’S MANUAL
In the spaces provided below, record the Model and Serial No. located at the bottom of
your projector.
Model No. Serial No.
Retain this information for future reference.
2
3
Before Using
SAFETY PRECAUTIONS
The lightni ng flash with arrowhea d sy mbol, within an e quila ter al triangl e, is
intended to alert the user to the presence of uninsulated "dangerou s voltage"
within the product's enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to
the presence of important operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES
ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE CABINET.
REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
WARNING:
USA only
Handling the cord on this product or cords associated with accessories sold with
this product, will expose you to lead, a chemical known to the State of California
to cause birth defects or other reproductive harm. Wash hands after handling.
USA only
Lamp conta ins mercury. Disposal of thi s product may be reg ulated due to
environmental conside rations. For disposal , reuse or re cycl ing information,
please contact your local government or the Electronic Industries Alliance at
www.eiae.org.
MODEL NAME: TLP-X100 / TLP-WX100
USA only
TRADE NAME: DATA PROJECTOR MODEL NAME: TLP-X100 / TLP-WX100
Tested To Comply
With FCC Standards
FOR HOME OR OFFICE USE
FCC NOTICE: This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
devic e, pursuan t to part 15 of th e FC C Rules. These limits are des ign ed to provide
reasonable protection against harmf ul interfe ren ce in a resid ent ial insta lla tio n. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause har mful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be deter mined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RESPONSIBLE PARTY: TOSHIBA AMERICA INFORMATION SYSTEMS, INC.
9740 Irvine Blvd., Irvine, CA 92618-1697 U.S.A
Phone: (949) 583-3000
CAUTION:
USA only
Changes or modifications made to this equipment, not expressly approved by
Toshiba, or parties authorized by Toshiba, could void the user’s authority to
operate the equipment.
Notice:
CANADA only
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil
numérique de la classe B est conforme à la norme NMB-003 du Canada.
Before Using
4
5
Before Using
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND
INSTRUCTIONS GIVEN IN THIS OWNER'S MANUAL AND THOSE
MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR FUTURE
REFERENCE.
This unit is fully transistorized and does not contain any parts that can be repaired by the
user.
WARNING: DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE
EXPOSED TO DANGEROUS VOLTAGE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL ONLY.
1. Read Owner’s Manual
After unpacking this product, read
the owner's manual carefully, and
follow all the operating and other
instructions.
2. Power Sources
This product should be operated
only from the type of power source
which does not exceed the voltage
range specified on the rating label
and the power cord.
If you are not sure of the type
of power supply to your home,
consult your product dealer or local
power company.
3. Source of Light
Do not look into the lens while the
lamp is on. The strong light from
the lamp may cause damage to
your eyesight.
4. Ventilation
Openings in the cabinet are
provided for ventilation and to
ensure reliable operation of the
product and to protect it from
overheating. These openings must
not be blocked or covered. Never
block an opening by placing the
product on a bed, sofa, rug or
other similar surface. Do not place
it in a built-in installation such as
a bookcase or rack, unless proper
ventilation is provided.
5. Heat
The product should be situated
away from heat sources such as
radiators, heat registers, stoves,
or other products (including
amplifiers) that produce heat.
6. Water and Moisture
Do not use this product near water.
- for example, near a bath tub,
wash bowl, kitchen sink, or laundry
tub; in a wet basement; or near a
swimming pool and the like.
7. Cleaning
Unplug this product from the wall
outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners.
Always use a soft cloth for
cleaning.
8. Be sure that you firmly
insert the plug into the wall
outlet.
Incorrect or faulty connections
may result in fire or electric shock.
Avoid using an unsound or loose
outlet.
9. Power Cord Protection
Power cords should be routed
so that they are not likely to be
walked on or pinched by items
placed upon or against them,
paying particular attention to cords
at plugs, convenience receptacles,
and the point where they exit from
the product.
10. Overloading
Do not overload wall outlets. To
reduce the risk of electric shock,
do not use the polarized plug with
an extension cord , receptacle, or
other outlet unless the blades can
be inserted completely with threewire grounding type to prevent
blade exposure. Failure to follow
these instructions may result in fire
or electric shock.
6
7
Before Using
IMPORTANT SAFETY INSTRUCTIONS (Continued)
11. Lightning storms
For added protection for this
product during a storm, or when it
is left unattended and unused for
long periods of time, unplug it from
the wall outlet. This will prevent
damage to the product due to
lightning and power-line surges.
Never operate this unit on AC
power during a thunderstorm. If
you see lightning or hear thunder,
never touch the unit, cables and/or
peripherals. An electric surge
caused by the storm, may result in
an electrical shock or damage to
the unit.
12. Object and Liquid Entry
Never push objects of any kind into
this product through openings as
they may touch dangerous voltage
points or short-out parts that could
result in a fire or electric shock.
Never spill liquid of any kind on the
product.
13. Do not place or keep the
projector within the reach
of the children.
It may fall or tip over, possibly
causing serious injury.
14. Do not place the product
vertically
Do not use the product in the
upright position or any other
vertical positions to project the
pictures. It may fall which could
result in serious injury and/or
damage to the product.
15. Stack Inhibited
Do not stack other equipment on
this product and do not place this
product on other equipment. The
top and bottom surface of this
product increase in temperature
during normal use and may
damage the other unit.
16. Attachments
Do not use attachments not
recommended by the product
manufacturer.
Use of an incompatible
attachments could cause hazards
or damage to the product.
17. Accessories
Do not place this product on
an unstable cart, stand, tripod,
bracket, or table. The product may
fall, causing serious injury to a
child or adult, and serious damage
to the product. A product and cart
combination should be moved with
care. Quick stops, excessive force,
and uneven surfaces may cause
the product and cart combination
to overturn.
S3125A
18. Damage Requiring Service
Unplug this product from the wall
outlet and take the product to
qualified service personnel if you
encounter any of the following
conditions:
a) The power supply cord or plug is
damaged.
b) Liquid has been spilled, or objects
have fallen into the product.
c) The product has been exposed to
rain or water.
d) The product does not operate
normally when following the
operating instructions. Adjust only
those controls that are covered by
the operating instructions since
an improper adjustment of other
controls may result in damage and
will often require extensive work by
a qualified technician to restore the
product to its normal operation.
e) The product has been dropped or
damaged in any way (If the cabinet
should break, please handle with
care to avoid injury) .
f) The product exhibits a distinct
change in performance, which
indicates a need for service.
8
9
Before Using
IMPORTANT SAFETY INSTRUCTIONS (Continued)
19. If glass components,
including lens and lamp,
should break, contact your
dealer for repair service.
This product incorporates glass
components, including a lens and
a lamp.
If these should break, please
handle with care to avoid injury
and contact your dealer for repair
service. Avoid any broken pieces of
glass since they may cause injury.
In the unlikely event that the lamp
ruptures, thoroughly clean the area
around the projector and discard
any edible items placed in that area
since they may be contaminated.
20. Servicing
Do not attempt to service this
product yourself as opening or
removing covers may expose you
to dangerous voltage or other
hazards. Refer all servicing to
qualified service personnel.
21. Replacement Parts
When replacement parts are
required, be sure the service
technician has used replacement
parts specified by the manufacturer
or have the same characteristics
as the original part.
Unauthorized substitutions may
result in fire, electric shock, or
other hazards.
(Only the replacement of the lamp
should be made by users.)
22. Safety Check
Upon completion of any service
or repairs to this product, ask
the service technician to perform
safety checks to verify that the
product is in proper operating
condition.
23. Do not leave thermalpaper documents or easily
deformed items on top
of the unit or near the air
exhaust for long periods of
time.
The heat from the unit could erase
the information on the thermal
paper, or cause deformation or
warping.
24. Do not use the product
in a closed installation
location.
Do not place the product in a box
or in any other closed installation
location. Otherwise it may
overheat, which could result in a
risk of fire.
POWER SUPPLY INFORMATION
If your line voltage is 220 to 240 V, use one of the following types of cable/plug.
Plug
configuration
Plug type
Australian
240 V
10 A
North American
240 V
15 A
Switzerland
240 V
6 A
Line voltage
EURO
UK
220 – 240 V
220 – 240 V
200 – 240 V
200 – 240 V
200 – 240 V
Plug
configuration
Plug type Line voltage
Use a 5 A fuse which is approved by
ASTA or BSI to BSI362.
Always replace the fuse cover after
changing the fuse.
IMPORTANT PRECAUTIONS
Moisture Condensation
Never operate this unit immediately after moving it from a cold location to a warm location.
When the unit is exposed to such a change in temperature, moisture may condense on the
lens and the crucial internal parts. Do not use the unit for at least 2 hours when there is an
extreme or sudden change in temperature to prevent the unit from possible damage.
Place and Manner of Installation
Do not place in hot locations, such as near heating equipment. Doing so could cause
malfunction, and shorten the life of the projector.
Avoid locations with oil or cigarette smoke. Doing so will dirty the optical parts, shortening
their lives, and darkening the screen.
Do not use this product in the upright position or tilt it up or down by more than 20° from
level. Doing so may cause a failure or shorten the life of the product.
Using this instrument near a TV or radio may cause interference to the images or audio
sound. If this happens, move it away from the TV or radio.
Moving the projector from a low-temperature room to a high-temperature room may cause
condensation on the lens or internal parts. If you continue to use it in that situation, it may
malfunction. Wait until the condensation naturally disappears.
In a high altitude location where air is thin, cooling efficiency is reduced so use the
projector with [Fan mode] set to [High].
p.41
Only plug the power cord into outlets rated for use with the power cord’s specified voltage range.
Do not overload extension cords or power strips as this can result in fire or electric shock.
Route the power cable or the connecting cable away from where people could trip over it.
The projector may fall down, which could result in severe injury.
Be sure the power cord is easily reached for unplugging in case of emergency. Do not
place any obstacles near a wall outlet in which the cord is plugged.
Avoid Volatile Liquid
Do not use volatile liquids, such as an insect spray, near the unit. Do not leave rubber or
plastic products touching the unit for a long time as they will leave marks on the finish.
Do not use a chemically saturated cloth.
•
•
•
•
•
•
•
•
•
10
11
Before Using
IMPORTANT PRECAUTIONS (Continued)
LCD Panel
If the air filter is stained and is clogged up, the main unit inner temperature rises. As a
result, the life of the LCD is shortened and a malfunction may also occur.
Clean the air filter from time to time and replace it regularly. It is recommended that this
replacement be done at the time of replacing a lamp. (Ask a dealer where the unit was
purchased or your nearby service station about an air filter for replacement.)
EXEMPTION CLAUSES
Toshiba Corporation bears no responsibility in the case of damages arising from natural
disaster such as earthquakes, lightning, etc., fire not liable to Toshiba Corporation, acts
by third parties, other accidents, or use under abnormal conditions including erroneous or
improper operation and other problems.
Toshiba Corporation bears no responsibility for incidental damages (lost profit, work
interruption, corruption or loss of the memory contents, etc.) arising from the use of or the
inability to use this unit.
Toshiba Corporation accepts no liability whatsoever for any damages arising from not
having followed the descriptions in this Owner’s Manual.
Toshiba Corporation accepts no liability whatsoever for any damages arising from
malfunctions arising from combination with equipment or software that is not related to
Toshiba Corporation.
OTHER INFORMATION
Copyrights
Showing or transmitting commercial imaging software or broadcast or cable-broad casting
programs with the purpose of other than the personal and private viewing, including
modifying images using the freeze or resize functions, or displaying with the varying
aspect ratio of the images, could violate the direct or indirect copyrights of the imaging
software or broadcast program, etc., if done without first consulting with the copyright
holder. For this reason, please take appropriate measures before performing one of the
actions listed above, including obtaining a license from the copyright holder.
Disposal
This product contains substances which are harmful to humans and the environment.
The lamp contains mercury.
Please dispose of this product or used lamps in accordance with local regulations.
Following information is only for EU-member states:
The use of the symbol indicates that this product may not be treated as
household waste. By ensuring this product is disposed of correctly, you will
help prevent potential negative consequences for the environment and human
health, which could otherwise be caused by inappropriate waste handling of
this product. For more detailed information about recycling of this product,
please contact your local city office, your household waste disposal service or
the shop where you purchased the product.
•
•
•
•
•
•
OTHER INFORMATION (Continued)
Trademarks
VGA, SVGA, XGA, SXGA, UXGA, WXGA are trademarks or registered trademarks of
International Business Machines Corporation.
Macintosh is a registered trademark of Apple Computer, Inc.
Windows is a registered trademark of Microsoft Corporation in the U.S. and other countries.
Adobe and Acrobat Reader are registered trademarks of Adobe Systems Incorporated.
All other brand and product names are trademarks or registered trademarks of their
respective companies.
Notational Conventions Used in This Manual
References to pages with related information are annotated as follows.
For example, if making a reference to page 36:
p.36
The illustrations in this document are for reference purposes only and may not reflect
your package exactly.
REMOTE CONTROL BATTERIES
Warning
Never throw batteries into a fire.
Using the batteries improperly may cause them to explode or leak and may result in serious injury.
If battery-leaking fluid contacts skin, wash the fluid off immediately with clean water and consult
a doctor. If the fluid spills on an instrument, avoid contact and wipe it off using tissue paper.
Then dispose of the used tissue paper as flammable garbage after moistening with water.
Notes
Be sure to use AAA (R03) size batteries.
Dispose of batteries in a designated disposal area.
Attention should be drawn to the environmental aspects of battery disposal.
Do not mix different battery types or combine used batteries with new ones.
If the remote control does not operate correctly, or if the operating range becomes
reduced, replace both batteries with new ones.
If the batteries are dead or if you will not be using the remote control for a long time,
remove the batteries to prevent battery acid from leaking into the battery compartment.
Following information is only for EU-member states:
[Disposal of batteries and/or accumulators]
The crossed out wheeled dust bin symbol indicates that batteries and/or
accumulators must be collected and disposed of separately from household
waste.
If the battery or accumulator contains more than the specified values of lead
(Pb), mercury (Hg), and/or cadmium (Cd) defined in the Battery Directive
(2006/66/EC), then the chemical symbols for lead (Pb), mercury (Hg) and/or
cadmium (Cd) will appear below the crossed out wheeled dust bin symbol.
By participating in separate collection of batteries, you will help to assure
the proper disposal of products and batteries and thus help to prevent
potential negative consequences for the environment and human health.
For more detailed information about the collection and recycling
programmes available in your country, please contact your local city office
or the shop where you purchased the product.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
12 13
Before Using
CONTENTS
Before Using
SAFETY PRECAUTIONS .............................................................................2
IMPORTANT SAFETY INSTRUCTIONS .......................................................4
POWER SUPPLY INFORMATION ................................................................ 9
IMPORTANT PRECAUTIONS .......................................................................9
EXEMPTION CLAUSES .............................................................................10
OTHER INFORMATION .............................................................................. 10
REMOTE CONTROL BATTERIES .............................................................. 11
CONTENTS ................................................................................................ 12
Preparations
Checking the package contents .................................................................. 14
Names of each part on the main unit ..........................................................15
Names of each part on the control panel and remote control .....................16
Names of the terminals on the rear panel ................................................... 18
Preparing and using the remote control ...................................................... 19
Placement ...................................................................................................20
Connection .................................................................................................. 22
Operations
Turning the power on and off ....................................................................... 24
Basic operations ..........................................................................................26
Using handy features ..................................................................................29
Using auto setting (For computer input only) ........................................... 29
Correcting the keystone distortion ...........................................................29
Resizing image ........................................................................................30
Cutting off the picture and sound temporarily (Mute) ...............................31
Changing picture mode ............................................................................31
Changing screen size ..............................................................................31
Freezing the image (Freeze) .................................................................... 32
Setting the password ...............................................................................32
Using the menus .........................................................................................34
Setup using the Setting display ................................................................ 34
The image adjustment menu ...................................................................35
The display setting menu ......................................................................... 37
The Default setting menu ......................................................................... 40
Displaying Information (Status display) .................................................... 42
Maintenance
About lamp .................................................................................................. 43
Lamp replacement ...................................................................................... 44
Air filter cleaning .......................................................................................... 47
Lens and main unit cleaning ....................................................................... 48
Others
Trouble indications ....................................................................................... 49
Troubleshooting ........................................................................................... 50
Specifications .............................................................................................. 52
14
15
Preparations
Checking the package contents
Preparations
Please make sure that the following items are included in the box, along with the main unit.
If any item is missing, immediately contact the store where you purchased the product.
(1) (4) (7)
(2) (5)
(3) (6)
(1) Remote control
(2) R03 (SIZE AAA) batteries for remote control (2)
(3) CD-ROM
(4)
Owner’s Manual
(5)
RGB cable (3 m)
[Note 1]
(6)
Power cord
[Note 1, 2]
(7)
Carrying bag
Notes
1: To maintain original performance, always use the supplied cables.
2: The shape and number of supplied power cords vary depending on the product destination.
Save Original Packing Materials
The original shipping carton and packing materials will come in handy if you ever have to
ship your projector. For maximum protection when shipping your projector, repack the set
as it was originally packed at the factory.
The Supplied CD-ROM
The supplied CD-ROM contains an owner’s manual including information not available for
the printed Owner’s manual (Getting started) in Portable Document Format (PDF). Please
use Acrobat Reader 5 or later version to view the manual.
Adobe® Acrobat® Reader® or Adobe® Reader
®
The supplied CD-ROM does not contain Acrobat® Reader®. If you cannot read PDF
files, please install Acrobat Reader software in your computer by downloading it from
the Adobe Systems website.
Viewing the manual
Run the CD-ROM and double-click on Start.pdf. Acrobat® Reader® launches, and the menu
screen of the Owner’s manual appears. Click on your language. The Owner’s Manual cover
and list of bookmarks appear. Click on a bookmark title to view that section of the manual.
Click on p. to view a reference page with related information. See the Help menu for more
information about Acrobat® Reader®.
Names of each part on the main unit
(16)(15) (15)(14) (14)(13)(10)(11) (12)
(9)(5)(4) (8)
(7)(6)(1)
(3)
(2)
Back Front
Name : Function
(1) Control panel :
Operates the projector.
p.16
(2) Zooming lever :
Adjusts screen size.
p.27
(3) Focusing lever :
Adjusts screen focus.
p.27
(4) Lamp cover :
Remove to replace lamp.
p.44
(5) Air exhaust : Expels air that has grown hot inside the projector.
(6) Air intake : Draws in air from outside the projector for internal cool
down.
(7) Lens cap :
Replace the cap when not using the projector to protect
the lens.
(8) Lens : Projects expanded image.
(9) Infrared remote sensor :
Senses commands from the remote control.
p.19
(10) AC IN socket : Connects the supplied power cord here.
(11)
Terminals on the rear panel
:
Connects external devices.
p.18
(12) Speaker : Outputs audio sound.
(13) Antitheft lock slot : Attach a safety cable or any other antitheft device.
(14)
Foot adjuster release button
:
Press to set up or stow the foot adjuster.
p.27
(15) Foot adjuster :
Adjusts the vertical projection angle.
p.27
(16) Air filter : Prevents dirt and dust from getting into the inside of the
projector.
p.47
16
17
Preparations
Names of each part on the control panel and remote control
Remote ControlControl panel
(1)
(8)
(3) (2)(4)
(6) (5)(7)
(7)
(9)
(8)
(10)
(11)
(12)
(13)
(1)
(2)
(3)
(4)
(6)
(5)
Battery cover
Name : Main Function
Control panel
(1) ENTER button : Accepts the selected mode.
(2) INPUT button :
Selects input.
p.26
(3) MENU button :
Displays menus.
p.34
(4) RETURN button : Goes back one screen.
(5) ON/STANDBY button/ :
Turns the power on/off (standby).
p.25
ON/STANDBY indicator :
Displays whether power is on or off (standby).
p.25
(6) TEMP indicator :
Lights when internal temperature is too high.
p.49
(7) LAMP indicator :
Displays lamp mode.
p.49
(8) Selection button :
Menu selections and adjustments, volume control,
Keystone adjustment, etc.
Remote control
(1) ON/STANDBY button :
Turns the power on/off (standby).
p.25
(2) FREEZE button :
Pauses image.
p.32
(3) MENU button :
Displays menus.
p.34
Name : Main Function
(4) ENTER button : Accepts the selected mode.
(5) RESIZE button : Enlarges image.
p.30
(6) SCREEN SIZE button : Changes screen size.
p.31
(7) MUTE button :
Cuts off the picture and sound temporarily.
p.31
(8) AUTO SET button :
Performs auto-adjustment of input signals from computer.
p.29
(9) INPUT button :
Selects input.
p.26
(10)
RETURN button
: Goes back one screen.
(11) Selection button :
Menu selections and adjustments, volume control,
Keystone adjustment, etc.
(12) PICTURE button : Changes image mode.
p.31
(13) Ten-Key button : Use when entering password.
Remote
control
button
Input
items
Remote
control
button
Input items
1
[1]
7
[7]
2
[2]
8
[8]
3
[3]
9
[9]
4
[4]
0
[0]
5
[5] Deletes one character.
6
[6]
Note
For the remainder of this manual, buttons are referred to as follows:
Selection buttons ⇒ ; ENTER button ⇒
•
Loading...