现货库存、技术资料、百科信息、热点资讯，精彩尽在鼎好!
TOSHIBA PHOTOCOUPLER GaAℓAs LED & PHOTO-IC
TLP116A
Plasma Display Panels (PDPs)
High-Speed Interface
Factory Automation (FA)
The Toshiba TLP116A mini-flat coupler is a small-outline coupler suitable
for surface-mount assembly.
The TLP116A consists of a GaAℓAs light-emitting diode and an integrated
high-gain, high-speed photodetector.
This unit is housed in the 6-pin SO package and guarantees a creepage
distance of ≥ 5.0mm, a clearance of ≥ 5.0mm and an insulation thickness
of ≥ 0.4mm. Therefore, the TLP116A meets the reinforced insulation class
requirements of international safety standards.
z Inverter logic (totem-pole output)
z SO6 package
5
6
1
3.7 ± 0.15
1.27
2.54
TLP116A
Unit: mm
4
3
0.4
4.55 ± 0.15
7.0 ± 0.4
0.15
2.1 ± 0.1
0.1
0.5 min
z Guaranteed performance over: -40 to 100°C
z Power supply voltage: 4.5 to 5.5V
z Input thresholds current: I
= 5 mA (max)
FHL
TOSHIBA 11－4L1
Weight: 0.08 g (typ.)
z Propagation delay time (tpHL / tpLH): 60 ns (max)
z Switching speed: 20 MBd (typ.)
z Common-mode transient immunity: ±10 kV/us
z Isolation voltage: 3750 Vrms
z UL approval: UL1577, File No.E67349 Under application
Truth Table Pin Configuration (Top View)
Input LED Tr1 Tr2 Output
H
ON OFF ON
OFF ON OFF H
L
L
Construction Mechanical Rating
Creepage Distance: 5.0mm (min)
Clearance: 5.0mm (min)
Insulation Thickness: 0.4mm (min)
1
3
SHIELD
Schematic
I
F
1+
VF
3－
VCC
GND
1: ANODE
6
3: CATHODE
5
4: GND
5: V
4
6: V
Tr1
Tr2
I
(Output)
O
CC
CC
V
CC
6
I
O
V
5
O
SHIELD
A bypass capacitor of 0.1μF must be
connected between pins 6 and 4.
GND
4
2008-10-01 1
Absolute Maximum Ratings (Ta=25°C)
Characteristic Symbol Rating Unit
Forward current IF 20 mA
Forward current derating (Ta ≥ 85°C) ΔIF / ΔTa -0. 5 m A / °C
LED
Peak transient forward current (Note 1) I
Reverse voltage VR 5 V
Output current IO 10 mA
Output voltage VO 6 V
Supply voltage VCC 6 V
DETECTOR
Output power dissipation PO 40 mW
Operating temperature range Topr -40 to 100 °C
Storage temperature range Tstg -55 to 125 °C
Lead solder temperature(10 s) Tsol 260 °C
Isolation voltage
(AC,1 min.,R.H.≤ 60%,Ta=25°C) (Note 2)
1 A
FPT
BVs 3750 Vrms
Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the
significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even
if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum
ratings and the operating ranges.
Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook
(“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test
report and estimated failure rate, etc).
Recommended Operating Conditions
TLP116A
Characteristic Symbol Min Typ. Max Unit
Input current , ON I
Input voltage , OFF V
Supply voltage (Note 3) VCC 4.5 5.0 5.5 V
Operating temperature Topr -40 — 100 °C
8
F(ON)
F(OFF)
0
—
—
18 mA
0.8 V
Note: Recommended operating conditions are given as a design guideline to obtain expected performance of the
device. Additionally, each item is an independent guideline respectively. In developing designs using this
product, please confirm specified characteristics shown in this document.
Correlation between Input current, switching speed and drive circuit
(reference information).
Input current
(IF)
12mA
8mA
8mA
(Page 4, With Speed up capacitor)
Note 1 : Pulse width PW ≤ 1μs, 300 pps.
Note 2 : This device is regarded as a two terminal device : pins 1 and 3 are shorted together, as are pins 4,5 and 6.
Note 3 : The detector of this product requires a power supply voltage (VCC) of 4.5 V or higher for stable operation.
If the V
is lower than this value, an ICC may increase, or an output may be unstable.
CC
Be sure to use the product after checking the supply current, and the operation of a power-on/-off.
Test Circuit Typical switching speed
1
(Page 4)
1
(Page 4)
2
21 – 23 MBd
18 – 20 MBd
23 – 27 MBd
2008-10-01 2
Electrical Characteristics
(Unless otherwise specified, Ta=-40 to 100°C, VCC=4.5 to 5.5 V )
Characteristic
Symbol
Te st
Circuit
Conditions Min Typ. Max Unit
TLP116A
Input forward voltage VF
Temperature coefficient
of forward voltage
Input reverse current IR
Input capacitance CT
Logic low output voltage VOL 1
Logic high output voltage VOH 2
Logic low supply current I
Logic high supply current I
Input current logic low
output
Input voltage logic high
output
ΔVF /ΔTa
3 IF = 12 mA
CCL
4 VF = 0 V
CCH
I
FHL
V
FLH
*All typical values are at Ta=25°C, V
=5 V, IF(ON)=12 mA unless otherwise specified
CC
Isolation Characteristics
(Ta = 25°C)
—
IF = 10 mA ,Ta = 25°C 1.45 1.58 1.85 V
—
IF = 10 mA
—
VR=5 V, Ta = 25°C
—
V = 0, f= 1 MHz, Ta = 25°C
IOL = 1.6 mA,
IF = 12 mA, VCC = 5 V
IOH = -0.02 mA,
VF = 1.05 V, VCC = 5 V
—
IO = 1.6 mA, VO < 0.4 V —
—
IO = -0.02 mA, VO > 4.0 V 0.8
—
-2.0 — mV/°C
— —
— 60
— —
4.0
— —
— —
— —
— 5 mA
— —
10 μA
— pF
0.4 V
5.0 mA
5.0 mA
V
V
Characteristic Symbol Test Conditions Min Typ. Max Unit
Capacitance input to output CS Vs = 0,f = 1 MHz (Note 2) ― 0.8 ― pF
12
Isolation resistance R
Isolation voltage BV
R.H. ≤ 60%, VS = 500 V
S
(Note 2)
AC,1 minute 3750 ― ―
AC,1 second,in oil ― 10000 ―
S
DC,1 minute,in oil ― 10000 ― Vdc
1×10
14
10
― Ω
Note 4:A ceramic capacitor(0.1 μF) should be connected from pin 6 to pin 4 to stabilize the operation of the high
gain linear amplifier. Failure to provide the bypass may impair the switching property.
The total lead length between capacitor and coupler should not exceed 1 cm.
V
rms
2008-10-01 3
Switching Characteristics
(Unless otherwise specified, Ta=-40 to 100°C, VCC=4.5 to 5.5 V)
Characteristic Symbol
Propagation delay time
to logic high output
Propagation delay time
to logic low output
Propagation delay time
to logic high output
Propagation delay time
to logic low output
Switching time dispersion
between ON and OFF
Output fall time(90-10%) tf
Output rise time(10-90%) tr
tpHL
tpLH
tpHL
tpLH
|tpHL-
tpLH|
Te st
Circuit
5
6
5
Conditions Min. Typ. Max. Unit
IF = 0→12 mA
IF = 12→0 mA
V
= 0→5 V
IN
(IF = 0→8 mA)
V
= 5→0 V
IN
(IF = 8→0 mA)
IF = 12 mA , R
CL =v15 pF (Note 5)
IF = 0→12 mA
IF = 12→0 mA
(Note 5)
= 100 Ω,
IN
R
= 100 Ω
IN
CL = 15 pF
(Note 5)
R
= 470 Ω
IN
27 pF
C
IN =
CL = 15 pF
= 100 Ω
R
IN
CL = 15 pF
(Note 5)
— —
— —
— —
— —
—
—
—
60 ns
60 ns
60 ns
60 ns
— 30
15
15
—
—
TLP116A
ns
ns
ns
Common mode transient
immunity at high Level
output
Common mode transient
immunity at low level
output
*All typical values are at Ta=25°C
Note 5: CL is approximately 15 pF which includes probe and Jig/stray wiring capacitance.
TEST CIRCUIT 1: V
IF
→
↑
1
3
TEST CIRCUIT 3: I
IF
→
↑
1
3
OL
SHIELD
CCL
SHIELD
CMH
CML
TEST CIRCUIT 2: V
6
VCC
0.1 μF
5
VOL
4
GND
V
I
CCL
6
VCC
GND
A
0.1 μF 0.1 μF
5
4
VCM = 1000 Vp-p, IF = 0 mA,
Vo(Min) = 4 V, Ta = 25°C
7
VCM = 1000 Vp-p, IF = 12 mA,
Vo(Max) = 0.4 V, Ta = 25°C
VCC
IOL
↑
TEST CIRCUIT 4: I
VCC
1
3
SHIELD
1
3
SHIELD
10000
-10000
OH
V
CC
GND
CCH
V
CC
GND
— —
— —
6
VOH
↑
V
5
0.1 μF
4
I
CCH
6
A
5
4
V/μs
V/μs
IOH
VCC
VCC
2008-10-01 4
TEST CIRCUIT 5: tpHL, tpLH
r
IF = 12 mA(P.G)
(f = 5 MHz , duty = 50%
less than tr
= tf = 5 ns)
INPUT
MONITORING
NODE
CL=15 pF
RIN=100 Ω
CL is capacitance of the probe and JIG.
(P.G): Pulse Generator
TEST CIRCUIT 6: tpHL, tpLH
VIN = 5 V(P.G)
(f = 5 MHz , duty = 50%
less than tr
= tf = 5 ns)
INPUT MONITORING NODE
CL=15 pF
CIN=27 pF
RIN=470 Ω
CL is capacitance of the probe and JIG.
(P.G): Pulse Generator
SHIELD
SHIELD
VCC
GND
VCC
GND
0.1 μF
0.1 μF
Vo
MONITORING
NODE
CL = 15 pF
Vo
MONITORING
NODE
CL=15 pF
TLP116A
IF
tf
tpHL
tpLH
VCC
VO
1.5 V
IF
VCC
VO
1.5 V
tf
tpHL
tpLH
tr
10%
tr
10%
90%
90%
50%
VOH
VOL
50%
VOH
VOL
TEST CIRCUIT 7: Common-Mode Transient Immunity Test Circuit
SW
A
IF
→
B
1
3
SHIELD
V
CM
VCC
GND
6
0.1
5
4
V
O
V
CC
・SW B : IF=0 mA
・SW A : IF=5 mA
CM
H
10%
=
90%
t
1000 V
tr
4V
)(800
V
s
μ
CM
)(
tf
CM
H
0.4 V
CML
)(800
V
=
L
)(
s
μ
t
f
2008-10-01 5
Specification for Embossed–Tape Packing (TPL)(TPR) for SO6 Coupler
1. Applicable Package
Package Product Type
SO6 Mini-flat coupler
2. Product Naming System
Type of package used for shipment is denoted by a symbol suffix after a product number. The method of
classification is as below.
(Example)
TLP116A(TPL)
Tape type
Device name
3. Tape Dimensions
3.1 Specification Classification Are as Shown in Table 1
TLP116A
Table 1 Tape Type Classification
Tape type Classification
TPL L direction 3000
TPR R direction 3000
3.2 Orientation of Device in Relation to Direction of Tape Movement
Device orientation in the recesses is as shown in Figure 1.
L direction R direction
Direction of Tape
Figure 1 Device Orientation
Quantity
(pcs/reel)
2008-10-01 6
3.3 Empty Device Recesses Are as Shown in Table 2.
Table 2 Empty Device Recesses
Standard Remarks
TLP116A
Occurrences of 2 or more
successive empty device
recesses
Single empty device
recesses
0
6 devices (max.) per reel Not including leader and trailer
Within any given 40-mm section of
tape, not including leader and trailer
3.4 Start and End of Tape
The start of the tape has 50 or more empty holes. The end of tape has 50 or more empty holes and two empty
turns only for a cover tape.
3.5 Tape Specification
(1) Tape material: Plastic (protection against electrostatics)
(2) Dimensions: The tape dimensions are as shown in Figure 2 and Table 3.
0.3 ± 0.05
φ1.5
+0.1
−0
G
A
E D
B
12.0 ± 0.3
K0
φ1.6 ± 0.1
3.15 ± 0.2
F
Figure 2 Tape Forms
Table 3 Tape Dimensions
Unit: mm
Unless otherwise specified: ±0.1
Symbol Dimension Remark
A 4.2 ―
B 7.6 ―
D 5.5 Center line of indented square hole and sprocket hole
E 1.75 Distance between tape edge and hole center
F 8.0 Cumulative error (max) per 10 feed holes
G 4.0 Cumulative error (max) per 10 feed holes
K0 2.8 Internal space
+0.1
-0.3
+0.1
-0.3
2008-10-01 7
3.6 Reel
(1) Material: Plastic
(2) Dimensions: The reel dimensions are as shown in Figure 3 and Table 4.
TLP116A
U
E
W1
W2
Figure 3 Reel Form
Table 4 Reel Dimensions
Unit: mm
Symbol Dimension
A Φ380 ±2
B Φ80 ±1
C Φ13 ±0.5
E 2.0 ±0.5
U 4.0 ±0.5
W1 13.5 ±0.5
W2 17.5 ±1.0
4. Packing
Either one reel or five reels of photocoupler are packed in a shipping carton.
5. Label Indication
The carton bears a label indicating the product number, the symbol representing classification of
standard, the quantity, the lot number and the Toshiba company name.
6. Ordering Method
When placing an order, please specify the product number, the tape type and the quantity as shown in the
(Example)
following example.
TLP116A (TPL) 3000 pcs
Quantity (must be a multiple of 3000)
Tape type
Device name
A
B
C
2008-10-01 8
TLP116A
RESTRICTIONS ON PRODUCT USE
• Toshiba Corporation, and its subsidiaries and affiliates (collectively “TOSHIBA”), reserve the right to make changes to the information
in this document, and related hardware, software and systems (collectively “Product”) without notice.
• This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with
TOSHIBA’s written permission, reproduction is permissible only if reproduction is without alteration/omission.
• Though TOSHIBA works continually to improve Product’s quality and reliability, Product can malfunction or fail. Customers are
responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and
systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily
injury or damage to property, including data loss or corruption. Before creating and producing designs and using, customers must
also refer to and comply with (a) the latest versions of all relevant TOSHIBA information, including without limitation, this document,
the specifications, the data sheets and application notes for Product and the precautions and conditions set forth in the “TOSHIBA
Semiconductor Reliability Handbook” and (b) the instructions for the application that Product will be used with or for. Customers are
solely responsible for all aspects of their own product design or applications, including but not limited to (a) determining the
appropriateness of the use of this Product in such design or applications; (b) evaluating and determining the applicability of any
information contained in this document, or in charts, diagrams, programs, algorithms, sample application circuits, or any other
referenced documents; and (c) validating all operating parameters for such designs and applications. TOSHIBA ASSUMES NO
LIABILITY FOR CUSTOMERS’ PRODUCT DESIGN OR APPLICATIONS.
• Product is intended for use in general electronics applications (e.g., computers, personal equipment, office equipment, measuring
equipment, industrial robots and home electronics appliances) or for specific applications as expressly stated in this document.
Product is neither intended nor warranted for use in equipment or systems that require extraordinarily high levels of quality and/or
reliability and/or a malfunction or failure of which may cause loss of human life, bodily injury, serious property damage or serious
public impact (“Unintended Use”). Unintended Use includes, without limitation, equipment used in nuclear facilities, equipment used
in the aerospace industry, medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic signaling
equipment, equipment used to control combustions or explosions, safety devices, elevators and escalators, devices related to electric
power, and equipment used in finance-related fields. Do not use Product for Unintended Use unless specifically permitted in this
document.
• Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part.
• Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any
applicable laws or regulations.
• The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any
infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to
any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise.
BSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE
• A
FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY
WHATSOEVER, INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR
LOSS, INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND
LOSS OF DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO
SALE, USE OF PRODUCT, OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT.
• GaAs (Gallium Arsenide) is used in Product. GaAs is harmful to humans if consumed or absorbed, whether in the form of dust or
vapor. Handle with care and do not break, cut, crush, grind, dissolve chemically or otherwise expose GaAs in Product.
• Do not use or otherwise make available Product or related software or technology for any military purposes, including without
limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile
technology products (mass destruction weapons). Product and related software and technology may be controlled under the
Japanese Foreign Exchange and Foreign Trade Law and the U.S. Export Administration Regulations. Export and re-export of Product
or related software or technology are strictly prohibited except in compliance with all applicable export laws and regulations.
• Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product.
Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances,
including without limitation, the EU RoHS Directive. TOSHIBA assumes no liability for damages or losses occurring as a result of
noncompliance with applicable laws and regulations.
2008-10-01 9
Loading...