Toshiba S1, Tecra S1-117, Tecra S1 Series User Manual

Download

Page 1

Tecra

S1 Series

User’s Guide

If you need assistance:

❖ Toshiba Global Support Centre

Calling within the United States (800) 457-7777

Calling from outside the United States (949) 859-4273

For more information, see Chapter 9 on page 185 of this guide.

Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling.

C6636-0903M2

Page 2

Model: Tecra S1 Series

ReWritable CD/DVD Drives

The computer system you purchased may include a ReWritable CD and/or DVD drive(s), among the most advanced data storage technologies available. As with any new technology, you must read and follow all set-up and usage instructions in the applicable user guides and/or manuals enclosed. If you fail to do so, this product may not function properly and you may lose data or suffer other damage. TOSHIBA AMERICA INFORMATION SYSTEMS (“TOSHIBA”), ITS AFFILIATES AND SUPPLIERS DO NOT WARRANT THAT OPERATION OF THE PRODUCT WILL BE UNINTERRUPTED OR ERROR FREE. YOU AGREE THAT TOSHIBA, ITS AFFILIATES AND SUPPLIERS SHALL HAVE NO RESPONSIBILITY FOR DAMAGE TO OR LOSS OF ANY BUSINESS, PROFITS, PROGRAMS, DATA OR REMOVABLE STORAGE MEDIA ARISING OUT OF OR RESULTING FROM THE USE OF THE PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY THEREOF.

Protection of Stored Data

For your important data, please make periodic back-up copies of all the data stored on the hard disk or other storage devices as a precaution against possible failures, alteration, or loss of the data. IF YOUR DATA IS ALTERED OR LOST DUE TO ANY TROUBLE, FAILURE OR MALFUNCTION OF THE HARD DISK DRIVE OR OTHER STORAGE DEVICES AND THE DATA CANNOT BE RECOVERED, TOSHIBA SHALL NOT BE LIABLE FOR ANY DAMAGE OR LOSS OF DATA, OR ANY OTHER DAMAGE RESULTING THEREFROM. WHEN COPYING OR TRANSFERRING YOUR DATA, PLEASE BE SURE TO CONFIRM WHETHER THE DATA HAS BEEN SUCCESSFULLY COPIED OR TRANSFERRED. TOSHIBA DISCLAIMS ANY LIABILITY FOR THE FAILURE TO COPY OR TRANSFER THE DATA CORRECTLY.

Critical Applications

The computer you have purchased is not designed for any “critical applications.” “Critical applications” means life support systems, medical applications, connections to implanted medical devices, commercial transportation, nuclear facilities or systems or any other applications where product failure could lead to injury to persons or loss of life or catastrophic property damage. ACCORDINGLY, TOSHIBA, ITS AFFILIATES AND SUPPLIERS DISCLAIM ANY AND ALL LIABILITY ARISING OUT OF THE USE OF THE COMPUTER PRODUCTS IN ANY CRITICAL APPLICATIONS. IF YOU USE THE COMPUTER PRODUCTS IN A CRITICAL APPLICATION,

Page 3

YOU, AND NOT TOSHIBA, ASSUME FULL RESPONSIBILITY FOR SUCH USE.

FCC Notice “Declaration of Conformity Information”

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

❖ Reorient or relocate the receiving antenna.

❖ Increase the separation between the equipment and receiver.

❖ Connect the equipment to an outlet on a circuit different from that to

which the receiver is connected.

❖ Consult the dealer or an experienced radio/TV technician for help.

NOTE

Only Peripherals complying with the FCC Class B limits may be attached to this computer. Operation with non-compliant peripherals or peripherals not recommended by Toshiba is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer's serial port, parallel port, monitor port, USB port, PS/2 Changes or modifications made to this equipment not expressly approved by Toshiba or parties authorized by Toshiba could void the user's authority to operate the equipment.

port and microphone jack.

❖ This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions:

❖ This device may not cause harmful interference.

❖ This device must accept any interference received, including

interference that may cause undesired operation.

Page 4

Contact:

Toshiba America Information Systems, Inc.

9740 Irvine Blvd.

Irvine, CA 92618-1697

(949) 583-3000

Industry Canada requirement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conformé à la norme NMB-003 du Canada.

FCC requirements

The following information is pursuant to FCC CFR 47, Part 68 and refers to internal modems.

This equipment complies with Part 68 of the FCC rules. On the bottom of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment. If requested, the information must be provided to the telephone company.

The modem connects to the telephone line by means of a standard jack called the USOC RJ11C.

A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant.

The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by the ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.

Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information.

Page 5

Telephone Company Procedures

The goal of the telephone company is to provide you with the best service it can. In order to do this, it may occasionally be necessary for them to make changes in their equipment, operations or procedures. If these changes might affect your service or the operation of your equipment, the telephone company will give you notice, in writing, to allow you to make any changes necessary to maintain uninterrupted service.

If Problems Arise

If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advanced notice is not practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.

If trouble is experienced with this equipment, for repair or limited warranty information, please contact Toshiba Corporation, Toshiba America Information Systems, Inc. or an authorized representative of Toshiba, or the Toshiba Support Centre within the United States at (800) 457-7777 or Outside the United States at (949) 859-4273. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.

Disconnection

If you should ever decide to permanently disconnect your modem from its present line, please call the telephone company and let them know of this change.

Fax Branding

The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device, including Fax machines, to send any message unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business or other entity, or other individual sending the message and the telephone number of the sending machine or such business, other entity, or individual. (The telephone number provided may not be a 900 number or any other number for which charges exceed local or long-distance transmission charges.)

In order to program this information into your fax transmission, refer to the fax software instructions installed on this computer.

Page 6

Alarm Equipment

If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.

Instructions for IC CS-03 Certified Equipment

1 NOTICE: The Industry Canada label identifies certified equipment.

This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.

Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.

Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.

2 The user manual of analog equipment must contain the equipment’s

Ringer Equivalence Number (REN) and an explanation notice similar to the following:

The Ringer Equivalence Number (REN) of this device can be found on the label affixed to your computer.

NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.

Page 7

3 The standard connecting arrangement (telephone jack type) for this

equipment is jack type(s): USOC RJ11C.

Wireless Interoperability

The TOSHIBA Wireless LAN Mini PCI Card products are designed to be interoperable with any wireless LAN product that is based on Direct Sequence Spread Spectrum (DSSS) radio technology, and is compliant to:

❖ The IEEE 802.11 Standard on Wireless LANs (Revision A/B), as

defined and approved by the Institute of Electrical and Electronics Engineers.

❖ The Wireless Fidelity (Wi-Fi) certification as defined by the WECA

Wireless Ethernet Compatibility Alliance.

If you should experience any such problem, immediately turn off either one of your Bluetooth™ or Wireless LAN.

Please contact Toshiba PC product support on Web site http://www.toshibaeurope.com/computers/tnt/bluetooth.htm in Europe or http://www.pcsupport.global.toshiba.com in the United States for more information.

This device is restricted to indoor use due to its operation in the 5.15 GHz to

5.85 GHz frequency range.

Wireless LAN and your Health

Wireless LAN products, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitted by Wireless LAN devices however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones.

Because Wireless LAN products operate within the guidelines found in radio frequency safety standards and recommendations, TOSHIBA believes Wireless LAN is safe for use by consumers. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.

Page 8

In some situations or environments, the use of Wireless LAN may be restricted by the proprietor of the building or responsible representatives of the organization. These situations may for example include:

❖ Using the Wireless LAN equipment on board of airplanes, or

❖ In any other environment where the risk of interference to other

devices or services is perceived or identified as harmful.

If you are uncertain of the policy that applies on the use of wireless devices in a specific organization or environment (e.g. airports), you are encouraged to ask for authorization to use the Wireless LAN device prior to turning on the equipment.

Regulatory Information

The TOSHIBA Wireless LAN Mini PCI Card must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product. This device complies with the following radio frequency and safety standards.

Canada – Industry Canada (IC)

This device complies with RSS 210 of Industry Canada.

The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada’s Web site www.hc-sc.gc.ca/rpb. The RF device shall not be co-located with any other transmitter that has not been tested with this device.

Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device.

L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes: (1) il ne doit pas produire de brouillage et (2) l’utilisateur du dispositif doit étre prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.

The term “IC” before the equipment certification number only signifies that the Industry Canada technical specifications were met.

To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.

Pour empecher que cet appareil cause du brouillage au service faisant l'objet d'une licence, il doit etre utilize a l'interieur et devrait etre place loin

Page 9

des fenetres afin de Fournier un ecram de blindage maximal. Si le matriel (ou son antenne d'emission) est installe a l'exterieur, il doit faire l'objet d'une licence.

Europe – EU Declaration of Conformity

❖ This device complies with the essential requirements of the R&TTE

Directive 1999/5/EC with essential test suites as per standards:

EN 60950 Safety of Information Technology equipment

ETS 300 328 Technical requirements for radio equipment

ETS 300 826 General EMC requirements for radio equipment.

België/ Belgique:

Deutschland: License required for outdoor installations. Check with reseller for pro-

For outdoor usage only channel 10 (2457 MHz) and 11 (2462 MHz) is allowed.

For private usage outside buildings across public grounds over less than 300m no special registration with IBPT/BIPT is required. Registration to IBPT/BIPT is required for private usage outside buildings across public grounds over more than 300m. An IBPT/BIPT license is required for public usage outside building. For registration and license please contact IBPT/BIPT.

Gebruik buiten gebouw alleen op kanalen 10 (2457 MHz) en 11 (2462 MHz). Voor privé-gebruik buiten gebouw over publieke groud over afstand kleiner dan 300m geen registratie bij BIPT/IBPT nodig; voor gebruik over afstand groter dan 300m is wel registratie bij BIPT/IBPT nodig. Voor publiek gebruik buiten gebouwen is licentie van BIPT/ IBPT verplicht. Voor registratie of licentie kunt u contact opnemen met BIPT.

L’utilisation en extérieur est autorisé sur le canal 10 (2457 MHz) et 11 (2462 MHz). Dans le cas d’une utilisation privée, a l’extérieur d’un bâtiment, audessus d’un espace public, aucun enregistrement n’est nécessaire pour une distance de moins de 300m. Pour une distance supérieure à 300m un enregistrement auprés de I’IBPT est requise. Pour une utilisation publique à I’extérieur de bâtiments, une licence de I’IBPT est requise. Pour les enregistrements et licences, veuillez contacter I’IBPT.

cedure to follow.

Page 10

Anmeldung im Outdoor-Bereich notwendig, aber nicht genehmigungspflichtig. Bitte mit Händler die Vorgehensweise abstimmen.

France: Restricted frequency band: only channels 10 and 11 (2457 MHz and

2462 MHz respectively) may be used in France. License required for every installation, indoor and outdoor installations. Please contact ART for procedure to follow.

Bande de fréquence restreinte: seuls les canaux 10 à 11 (2457 MHz et 2462 MHz respectivement) doivent être utilisés en France. Toute utilisation, qu’elle soit intérieure ou extérieure, est soumise à autorisation. Vous pouvez contacter I’Autorité de Régulation des Télécommuniations (http://www.art-telecom.fr) pour la procédure à suivre.

Italia: License required for indoor use. Use with outdoor installations not

allowed.

E’necessaria la concessione ministeriale anche per l’uso interno. Verificare con i rivenditori la procedura da seguire. L’uso per installazione in esterni non e’ permessa.

Nederland: License required for outdoor installations. Check with reseller for pro-

cedure to follow.

Licentie verplicht voor gebruik met buitenantennes. Neem contact op met verkoper voor juiste procedure.

USA – Federal Communications Commission (FCC)

This device complies with Part 15 of FCC Rules. Operation of the devices in a Wireless LAN System is subject to the following two conditions:

❖ This device may not cause harmful interference.

❖ This device must accept any interference that may cause undesired

operation.

TOSHIBA is not responsible for any radio or television interference caused by unauthorized modification of the devices included with this TOSHIBA Wireless LAN Mini PCI Card, or the substitution or attachment of connecting cables and equipment other than specified by TOSHIBA.

The correction of interference caused by such unauthorized modification, substitution or attachment will be the responsibility of the user.

Page 11

Caution: Exposure to Radio Frequency Radiation

The Toshiba Wireless LAN Mini PCI Card will be installed with one of two types of antennas. The both of antenna types, when installed are located at the upper edge of the LCD screen.

For both antennas, the radiated output power of the TOSHIBA Wireless LAN Mini PCI Card is far below the FCC radio frequency exposure limits. Nevertheless, the TOSHIBA Wireless LAN Mini PCI Card shall be used in such a manner that the potential for human contact during normal operation is minimized. In normal operating configuration, the LCD in the upright position, the distance between the antenna and the user should not be less than 20 cm. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Antenna(s) used in 5.15 GHz to 5.25 GHz frequency band must be integral antenna which provide no access to the end user.

Refer to the Regulatory Statements as identified in the documentation that comes with those products for additional information.

Caution: Radio Frequency Interference Requirements

This device is restricted to indoor use due to its operation in the 5.15 GHz to 5.25 GHz frequency range. FCC requires this product to be used indoors for frequency range 5.15 GHz to 5.25 GHz to reduce the potential for harmful interference to co-channel Mobile Satellite systems.

High power radars are allocated as primary users of the 5.25 GHz to 5.35 GHz and 5.65 GHz to 5.85 GHz bands. These radar stations can cause interference with and/or damage this device.

NOTE

The above Caution information applies to products that operate with an

802.11a device.

Taiwa n

Article 14 Unless approved, for any model accredited low power radio frequency

electric machinery, any company, trader or user shall not change the frequency, increase the power or change the features and functions of the original design.

Page 12

Article 17 Any use of low power radio frequency electric machinery shall not

affect the aviation safety and interfere with legal communications. In event that any interference is found, the use of such electric machinery shall be stopped immediately, and reusing of such products can be resumed until no interference occurs after improvement.

The legal communications mentioned in the above item refer to radio communications operated in accordance with telecommunication laws and regulations.

Low power radio frequency electric machinery shall resist against interference from legal communications or from industrial, scientific and medical radio emission electric machinery.

Using this Equipment in Japan

In Japan, the frequency bandwidth of 2,400 MHz to 2,483.5 MHz for second generation low-power data communication systems such as this equipment overlaps that of mobile object identification systems (premises radio station and specified low-power radio station).

1. Sticker

Please put the following sticker on devices incorporating this product.

2. Indication

The indication shown below appears on this equipment.

1 2.4: This equipment uses a frequency of 2.4 GHz.

2 DS: This equipment uses DS-SS modulation.

3 The interference range of this equipment is less than 40m.

4 This equipment uses a frequency bandwidth from 2,400 MHz to

2,483.5 MHz.

Page 13

It is possible to avoid the band of mobile object identification systems.

3. TOSHIBA Direct PC

Monday – Friday: 10:00 – 17:00

Toll Free Tel: 0120-13-1100

Direct Dial: 03-3457-5916

Fax: 03-5444-9450

Device Authorization

This device obtains the Technical Regulation Conformity Certification and the Technical Conditions Compliance Approval, and it belongs to the device class of radio equipment of low-power data communication system radio station stipulated in the Radio Law and the Telecommunications Business Law of Japan.

The Name of the radio equipment: MPC13A-20/R

JAPAN APPROVALS INSTITUTE FOR TELECOMMUNICATIONS EQUIPMENT

Approval Number: D01-1128JP

TELECOM ENGINEERING CENTER Approval Number: 03NY.A0018, 03GZDA0017

The following restrictions apply:

❖ Do not disassemble or modify the device.

❖ Do not install the embedded wireless module into other device.

Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

❖ Reorient or relocate the receiving antenna.

❖ Increase the distance between the equipment and the receiver.

Page 14

❖ Connect the equipment to an outlet on a circuit different from that to

which the receiver is connected.

❖ Consult the dealer or an experienced radio/TV technician for help.

Toshiba is not responsible for any radio or television interference caused by unauthorized modification of the devices included with this Toshiba Wireless LAN Mini PCI Card, or the substitution or attachment of connecting cables and equipment other than specified by Toshiba.

The correction of interference caused by such unauthorized modification, substitution or attachment will be the responsibility of the user.

NOTE

The following information is dependent on what type of wireless device is in your computer.

Approved Countries/Regions for use for the Atheros AR5001X Mini PCI Wireless network adapter

This equipment is approved to the radio standard by the countries/regions in the following table.

Do not use this equipment except in the countries/regions in the following table.

NOTE

802.11b (2.4 GHz)

This device works on passive scan only.

A peer-to-peer mode is not available in 802.11a and Turbo Mode.

Australia Austria Belgium

Canada Denmark Finland

France Germany Greece

Ireland Italy Liechtenstein

Luxembourg Netherlands New Zealand

Norway Portugal Sweden

Switzerland UK USA

Page 15

802.11a (5 GHz)

Australia Austria Belgium

Canada Denmark Finland

France Germany Greece

Ireland Italy Liechtenstein

Luxembourg Netherlands New Zealand

Norway Portugal Sweden

Switzerland UK USA

Turbo Mode (5 GHz)

Canada USA

Approved Countries/Regions for use for the Intel® PRO/ Wireless LAN 2100 3B Mini PCI Adapter

This equipment is approved to the radio standard by the countries/regions in the following table.

Do not use this equipment except in the countries/regions in the following table.

Argentina Australia Austria

Belgium Brazil Canada

Chile Denmark Finland

France Germany Greece

Iceland Ireland Italy

Japan Liechtenstein Luxembourg

Mexico Netherlands New Zealand

Norway Peru Portugal

Singapore Spain Sweden

Switzerland UK Uruguay

USA Venezuela

Page 16

Approved Countries/Regions for use for the Toshiba Mini PCI Wireless LAN Card

This equipment is approved to the radio standard by the countries/regions in the following table.

Do not use this equipment except in the countries/regions in the following table.

Australia Austria Belgium

Canada Denmark Finland

France Germany Greece

Hong Kong Iceland Ireland

Italy Japan Liechtenstein

Luxembourg Malaysia Netherlands

New Zealand Norway Philippines

Portugal Singapore Spain

Sweden Switzerland Thailand

UK USA

Bluetooth wireless technology Interoperability

Bluetooth™ Cards from TOSHIBA are designed to be interoperable with any product with Bluetooth wireless technology that is based on Frequency Hopping Spread Spectrum (FHSS) radio technology, and is compliant to:

❖ Bluetooth Specification Ver. 1.1, as defined and approved by The

Bluetooth Special Interest Group.

❖ Logo certification with Bluetooth wireless technology as defined by

The Bluetooth Special interest Group.

Page 17

Bluetooth wireless technology is a new innovative technology, and TOSHIBA has not confirmed compatibility of its Bluetooth™ products with all PCs and/ or equipment using Bluetooth wireless technology other than TOSHIBA portable computers.

Always use Bluetooth™ cards from TOSHIBA in order to enable wireless networks over two or more (up to a total of seven) TOSHIBA portable computers using these cards. Please contact TOSHIBA PC product support on Web site http://www.toshiba-europe.com/computers/tnt/bluetooth.htm in Europe or http://www.pcsupport.global.toshiba.com in the United States for more information.

When you use Bluetooth™ cards from TOSHIBA close to 2.4 GHz Wireless LAN devices, Bluetooth transmissions might slow down or cause errors. If you detect certain interference while you use Bluetooth™ cards from TOSHIBA, always change the frequency, move your PC to the area outside of the interference range of 2.4 GHz Wireless LAN devices (40 meters/43.74 yards or more) or stop transmitting from your PC. Please contact TOSHIBA PC product support on Web site http://www.toshiba-europe.com/computers/ tnt/bluetooth.htm in Europe or http://www.pcsupport.global.toshiba.com in the United States for more information.

Bluetooth™ and Wireless LAN devices operate within the same radio frequency range and may interfere with one another. If you use Bluetooth™ and Wireless LAN devices simultaneously, you may occasionally experience a less than optimal network performance or even lose your network connection. If you should experience any such problem, immediately turn off either one of your Bluetooth™ or Wireless LAN. Please contact Toshiba PC product support on Web site http:// www.toshiba-europe.com/computers/tnt/bluetooth.htm in Europe or http:// www.pcsupport.global.toshiba.com in the United States for more information.

Bluetooth wireless technology and your Health

The products with Bluetooth wireless technology, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitted by devices with Bluetooth wireless technology however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones.

Because products with Bluetooth wireless technology operate within the guidelines found in radio frequency safety standards and recommendations, TOSHIBA believes Bluetooth wireless technology is safe for use by consumers. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.

Page 18

In some situations or environments, the use of Bluetooth wireless technology may be restricted by the proprietor of the building or responsible representatives of the organization. These situations may for example include:

❖ Using the equipment with Bluetooth wireless technology on board of

airplanes, or

❖ In any other environment where the risk of interference to other

devices or services is perceived or identified as harmful.

If you are uncertain of the policy that applies on the use of wireless devices in a specific organization or environment (e.g. airports), you are encouraged to ask for authorization to use the device with Bluetooth wireless technology prior to turning on the equipment.

Regulatory statements

This product complies with any mandatory product specification in any country/region where the product is sold. In addition, the product complies with the following:

European Union (EU) and EFTA

This equipment complies with the R&TTE directive 1999/5/EC and has been provided with the CE mark accordingly.

Canada-Industry Canada (IC)

This device complies with RSS 210 of Industry Canada.

L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes: (1) il ne doit pas produire de brouillage et (2) l’utilisateur du dispositif doit étre prét à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.

The term “IC” before the equipment certification number only signifies that the Industry Canada technical specifications were met.

Caution: FCC Interference Statement

This device complies with part15 of the FCC rules. Operation is subject to the following two conditions:

❖ This device may not cause harmful interference, and

Page 19

❖ This device must accept any interference received, including

interference that may cause undesired operation.

Note that any changes or modifications to this equipment not expressly approved by the manufacturer may void the authorization to operate this equipment.

Caution: Exposure to Radio Frequency Radiation

The radiated output power of the Bluetooth™ Card from TOSHIBA is far below the FCC radio frequency exposure limits. Nevertheless, the Bluetooth™ Card from TOSHIBA shall be used in such a manner that the potential for human contact during normal operation is minimized.

In order to comply with FCC radio-frequency radiation exposure guidelines for an uncontrolled environment, the Bluetooth™ Card from TOSHIBA has to be operated while maintaining a minimum body to antenna which are located on top of LCD distance of 20 cm.

Refer to the Regulatory Statements as identified in the documentation that comes with those products for additional information.

The Bluetooth™ Card from TOSHIBA is far below the FCC radio frequency exposure limits.

Nevertheless, it is advised to use the Bluetooth™ Card from TOSHIBA in such a manner that human contact during normal operation is minimized.

NOTE

Changes or modifications made to this equipment not expressly approved by TOSHIBA or parties authorized by TOSHIBA could void the user’s authority to operate the equipment.

Taiwa n

Article 14 Unless approved, for any model accredited low power radio frequency

electric machinery, any company, trader or user shall not change the frequency, increase the power or change the features and functions of the original design.

Article 17 Any use of low power radio frequency electric machinery shall not

Page 20

The legal communications mentioned in the above item refer to radio communications operated in accordance with telecommunication laws and regulations.

Low power radio frequency electric machinery shall resist against interference from legal communications or from industrial, scientific and medical radio emission electric machinery.

Using this equipment in Japan

1. Sticker

Please put the following sticker on devices incorporating this product.

2. Indication

The indication shown below appears on this equipment.

(1) (2) (3)

2.4FH1

(4)

1 2.4: This equipment uses a frequency of 2.4 GHz.

2 FH: This equipment uses FH-SS modulation.

3 The interference range of this equipment is less than 10m.

4 This equipment uses a frequency bandwidth from 2,400 MHz to

2,483.5 MHz. It is impossible to avoid the band of mobile object identification systems.

Page 21

3. TOSHIBA Direct PC

Monday – Friday: 10:00 – 17:00

Toll Free Tel: 0120-13-1100

Direct Dial: 03-3457-5916

Fax: 03-5444-9450

Device Authorization

This device obtains the Technical Regulation Conformity Certification, and it belongs to the device class of radio equipment of low-power data communication system radio station stipulated in the Radio Law of Japan.

The Name of the radio equipment: EYXF2CS

TELECOM ENGINEERING CENTER

Approval Number: 01NYDA1305

The following restrictions apply:

❖ Do not disassemble or modify the device.

❖ Do not install the embedded wireless module into other device.

DVD-ROM, multi-function drive safety instructions

The DVD-ROM and multi-function drives employ a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.

Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure.

To prevent direct exposure to the laser beam, do not try to open the enclosure.

Page 22

Location of the required label

(Sample shown below. Location of the label and manufacturing information may vary.)

This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the user’s guide carefully and keep it for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” To prevent direct exposure to the laser beam, do not try to open the enclosure.

Use of controls or adjustments or performance of procedures other than those specified in the owner’s manual may result in hazardous radiation exposure.

This guide is copyrighted by Toshiba America Information Systems, Inc. with all rights reserved. Under the copyright laws, this guide cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed, however, with respect to the use of the information contained herein.

Export Administration Regulation

This document contains technical data that may be controlled under the U.S. Export Administration Regulations, and may be subject to the approval of the U.S. Department of Commerce prior to export. Any export, directly or indirectly, in contravention of the U.S. Export Administration Regulations is prohibited.

Page 23

Notice

The information contained in this manual, including but not limited to any product specifications, is subject to change without notice.

TOSHIBA CORPORATION AND TOSHIBA AMERICA INFORMATION SYSTEMS, INC. (TOSHIBA) PROVIDES NO LIMITED WARRANTY WITH REGARD TO THIS MANUAL OR ANY OTHER INFORMATION CONTAINED HEREIN AND HEREBY EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE WITH REGARD TO ANY OF THE FOREGOING. TOSHIBA ASSUMES NO LIABILITY FOR ANY DAMAGES INCURRED DIRECTLY OR INDIRECTLY FROM ANY TECHNICAL OR TYPOGRAPHICAL ERRORS OR OMISSIONS CONTAINED HEREIN OR FOR DISCREPANCIES BETWEEN THE PRODUCT AND THE MANUAL. IN NO EVENT SHALL TOSHIBA BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL, OR EXEMPLARY DAMAGES, WHETHER BASED ON TORT, CONTRACT OR OTHERWISE, ARISING OUT OF OR IN CONNECTION WITH THIS MANUAL OR ANY OTHER INFORMATION CONTAINED HEREIN OR THE USE THEREOF.

Trademarks

Satellite and Noteworthy are registered trademarks, SelectServ, FreedomWare, and SmartMedia are trademarks, of Toshiba America Information Systems, Inc. and/or Toshiba Corporation.

Microsoft, Windows, DirectX, Active Desktop, and DirectShow are registered trademarks, and Windows Media is a trademark of Microsoft Corporation.

LapLink is a registered trademark of Traveling Software, Inc.

ConfigFree is a trademark of Toshiba Corporation.

Wi-Fi is a registered trademark of Wi-Fi Alliance.

Dolby - Manufactured by Toshiba under license from Dolby Laboratories/ Dolby and the double-D symbol are trademarks of Dolby Laboratories.

TouchPad is a trademark of Synaptics, Inc.

All other brand and product names are trademarks or registered trademarks of their respective companies.

Page 24

Computer Disposal Information

This product contains mercury. Disposal of this material may be regulated due to environmental considerations. For disposal, reuse or recycling information, please contact your local government or the Electronic Industries Alliance at www.eiae.org.

Page 25

Introduction ...............................................................34

Chapter 1: Finding Your Way Around ..................................... 38

Making sure you have everything............................38

Finding where everything is located ........................38

Front with the display panel closed......................39

Back.....................................................................40

Left side ...............................................................41

Right side.............................................................42

Front with the display panel open ........................43

Underside ............................................................45

Indicator panel lights...............................................46

System indicator panel lights...............................46

Keyboard indicator panel lights............................47

Chapter 2: Getting Started........................................................ 49

Selecting a place to work ........................................49

Creating a computer-friendly environment...........49

Keeping yourself comfortable ..............................50

Other precautions....................................................53

Setting up your computer ....................................54

Page 26

Contents

Connecting the AC adapter...................................55

Charging the battery ............................................58

Turning on the computer.........................................58

Opening the display panel....................................58

Turning on the power...........................................59

Setting up your software .........................................60

Registering your computer with Toshiba.................61

Setting up other devices ......................................61

Turning off the computer ........................................62

Closing the display panel .....................................63

Chapter 3: Connecting Other External Devices....................... 64

Using external display devices ................................64

Connecting the display device..............................64

Directing the display output when you turn on the

computer .............................................................66

Adjusting the quality of the external display.........67

Video limitations ..................................................67

Using an external keyboard .....................................68

Making your external keyboard emulate

the Fn key ............................................................69

Using a mouse ........................................................69

Setting up a PS/2 mouse with the AccuPoint II....69

Connecting a local printer ......................................70

Connecting an external diskette drive......................71

Connecting external speakers or headphones .........72

Connecting an external microphone........................72

Using an expansion device......................................73

Adding memory.......................................................73

Installing a memory module ................................74

Removing a memory module...............................76

Using Slim SelectBay

Removing a module from the Slim SelectBay

Inserting a module into the Slim SelectBay®........79

modules..............................77

....78

Page 27

Contents

Inserting and removing hard drives.........................80

Inserting and removing PC Cards............................82

Inserting a PC Card..............................................82

Removing a PC Card............................................83

Setting up a PC Card for your computer ..............84

Inserting an SD® card..............................................84

Connecting your modem to a telephone line ...........85

Connecting to a phone line .................................86

Chapter 4: Learning the Basics................................................ 88

Computing tips........................................................88

Using the keyboard .................................................89

Character keys ....................................................90

Making your keyboard emulate a full-size

keyboard ..............................................................90

Ctrl, Fn, and Alt keys ............................................91

Function keys.......................................................91

Windows special keys..........................................92

Overlay keys ........................................................92

Using the AccuPoint II pointing device....................94

Using the TouchPad™ .............................................95

Control buttons....................................................96

Disabling or enabling the Dual Pointing Device....96

Using TOSHIBA Console .........................................97

Starting a program ..................................................98

Starting a program from the Start menu..............98

Starting a program from Windows

Starting a program from the Run dialog box .....100

Saving your work ..................................................101

Printing your work ................................................103

Using the DVD-ROM or multi-function drive .........104

Inserting compact discs ....................................106

Removing compact discs ..................................108

Caring for CDs and DVDs...................................108

Explorer ......99

Page 28

Contents

Using PC Cards .....................................................109

Hot swapping.....................................................109

Using SD® cards ..................................................110

Using your computer at the office .........................111

Using a computer lock ..........................................111

Caring for your computer......................................112

Cleaning the computer.......................................112

Moving the computer.........................................113

Powering down the computer ...............................113

Using Turn Off or Shut down .............................114

Using Hibernation ..............................................117

Using Standby ...................................................119

Chapter 5: Mobile Computing................................................ 123

Toshiba’s energy-saver design..............................123

Running the computer on battery power...............123

Battery Notice ....................................................124

Charging the batteries........................................124

Charging the RTC battery...................................125

Monitoring battery power ..................................126

What to do when the battery alarm sounds...........128

Changing batteries ................................................129

Taking care of your battery....................................131

Safety precautions .............................................131

Maximizing battery life.......................................132

Disposing of used batteries safely .....................133

Conserving power .................................................134

Power usage modes in Windows

XP Professional .................................................135

Using a hot key to set the power usage mode....135

Additional options for power .................................136

Page 29

Contents

Chapter 6: Exploring Your Options........................................ 137

Exploring the desktop............................................137

Finding your way around the desktop ................137

Exploring audio features........................................141

Using external speakers or headphones.............142

Recording sounds..............................................143

Playing an audio CD-ROM .................................144

Exchanging data with another computer ...............145

Transferring files................................................146

Getting help transferring files.............................146

Setting up for communications..........................146

Connecting the modem to a telephone line ........148

Connecting your computer to a network ...........148

Toshiba’s online resources ................................151

An overview of using the Internet..........................151

The Internet .......................................................152

The World Wide Web ........................................152

Internet Service Providers..................................152

Connecting to the Internet ................................153

Surfing the Internet............................................153

Internet features.................................................154

Uploading and downloading files from the Internet 155

Chapter 7: Toshiba Utilities..................................................... 156

Hotkey Utility.........................................................157

TOSHIBA Console .................................................157

TOSHIBA Accessibility...........................................159

Fn-esse®................................................................160

Starting Fn-esse ................................................160

Using the keyboard or pointing device to

assign keys ........................................................162

Viewing existing key assignments......................163

Page 30

Contents

Changing or removing existing key

assignments ......................................................164

Toshiba HW Setup ................................................164

Accessing Toshiba HW Setup ............................164

Power Saver..........................................................167

Mobile Extension...................................................168

Chapter 8: Keeping Your Files Safe........................................ 170

Using passwords in Windows ..............................170

User-level passwords ...........................................171

Setting a user-level password............................171

Using an instant password.................................172

Setting a user password ....................................173

Disabling a user password.................................175

Using the instant password ...............................176

Using a supervisor password................................177

Setting a supervisor password...........................177

Deleting a supervisor password.........................178

Hard disk drive passwords....................................179

Setting a hard disk drive master password ........180

Setting a hard disk drive user password ............182

Deleting the hard disk drive user password .......183

Chapter 9: Troubleshooting Guide......................................... 185

Problems that are easy to fix.................................185

Problems when you turn on the computer ............186

Resolving a hardware conflict ...............................188

Using the Windows XP troubleshooting feature.188

A plan of action..................................................188

Resolving hardware conflicts on your own ........189

Memory module problems.................................191

Power and the batteries .....................................192

Keyboard problems............................................193

AccuPoint II problems .......................................194

Page 31

Contents

Display problems ...............................................195

Disk drive problems...........................................197

Modem problems...............................................199

Problems with the DVD-ROM or

multi-function drive ...........................................199

Sound system problems ....................................201

Optional devices.................................................201

PC Card problems..............................................201

Printer problems................................................204

Internet Problems .................................................205

DVD operating problems–Windows XP.................206

Developing good computing habits.......................209

If you need further assistance ...............................210

Before you call ...................................................210

Contacting Toshiba ............................................211

Other Toshiba Internet Web sites .........................212

Toshiba’s worldwide offices .................................212

Appendix A: Windows 2000 Supplemental Information .... 216

Using your computer for the first time...............216

Setting up your software....................................216

Completing installation ......................................217

Completing the initial startup procedure ............217

Connecting to the Internet.....................................218

Setting up a printer ...............................................218

Turning off the computer ......................................220

Exploring the desktop............................................221

Using the Start menu .........................................221

Using Windows 2000 Professional online Help..222

Viewing your computer’s contents........................223

Using Windows Explorer ...................................223

Naming your files...............................................224

Backing up your work ...........................................224

Restoring your work..............................................225

Running the computer on battery power...............226

Page 32

Contents

Powering down the computer ...............................226

Shut down command.........................................227

Hibernation command .......................................227

Standby command.............................................228

Using Shut down...................................................229

Shutting down more quickly ..............................229

Starting again after Shut down ..........................231

Using Hibernation .................................................231

Enabling the Hibernation Command...................231

Going into Hibernation mode more quickly........233

Starting again from Hibernation.........................234

Using Standby.......................................................234

Going into Standby mode more quickly .............235

Starting again from Standby ..............................236

Quickly changing your Shut down mode ...........236

Toshiba Utilities.....................................................237

Toshiba Hardware Setup....................................237

Appendix B: Hot Keys............................................................. 240

Volume Mute.........................................................240

Instant password security .....................................240

Without a password...........................................241

With a password ................................................241

Power usage mode ...............................................242

Standby mode .......................................................243

Hibernation mode .................................................243

Display modes.......................................................244

Display brightness.................................................244

Wireless device enable ..........................................245

Disabling or enabling the

Touchpad/AccuPoint II..........................................245

Keyboard hot keys ................................................246

Page 33

Contents

Appendix C: Using ConfigFree™ with your

Toshiba Computer................................................................... 247

Getting Started ......................................................248

ConfigFree Main Screen.....................................248

Starting ConfigFree ............................................249

Configuring ConfigFree ......................................249

ConfigFree Utilities ................................................250

Connectivity Doctor ...........................................250

Device Settings ..................................................251

Profile Settings ..................................................253

Quick Connect....................................................254

Using Auto Switch.................................................255

Auto Switch (Cable Disconnect).........................256

Auto Switch (SSID)............................................256

Appendix D: Power Cable Connectors.................................. 257

Glossary...................................................................258

Index ........................................................................272

Page 34

Introduction

Welcome to the world of powerful, portable multimedia computing. With your Toshiba notebook computer, your work can accompany you wherever you go.

Tecra S1 Series notebook computers provide considerable computing power, enabling you to perform the most demanding computing tasks from any location.

You will find your operating system, Microsoft XP, already installed on your computer. Your operating system offers exciting features and easy Internet access.

Windows®

NOTE

While Toshiba has made every effort at the time of publication to ensure the accuracy of the information provided herein, product specifications, configurations, prices, system/component/options availability are all subject to change without notice. For the most up-to-date product information about your computer, or to stay current with the various computer software or hardware options, visit Toshiba's Web site at pcsupport.toshiba.com.

Page 35

This guide

This user’s guide contains basic information about your computer, including troubleshooting advice, detailed descriptions of your computer’s hardware and how to use it, and vital notes about Microsoft

Depending on your needs, you can:

❖ Read the entire guide from beginning to end.

❖ Skim through and stop when a topic interests you.

❖ Use the table of contents and the index to find specific

information.

If you are new to computers or have not used a notebook computer before, read through the first couple of chapters to familiarize yourself with the components of the computer. After that, seek out whatever interests you most.

Safety icons

Introduction

Windows® XP.

This manual contains safety instructions that must be observed in order to avoid potential hazards that could result in personal injuries or damage to your equipment. The safety instructions have been classified according to the seriousness of the risk, and are highlighted with icons as follows:

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

Page 36

Introduction

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

Indicates a potentially hazardous situation which, if not avoided, may result in property damage.

NOTE

Provides important information.

Other icons used

Additional icons highlight other helpful or educational information:

TECHNICAL NOTE: This icon highlights technical information about the unit.

HINT: This icon denotes helpful hints and tips.

DEFINITION: This icon indicates the definition of a term used in the text.

Page 37

Making sure you have everything

Before you do anything else, consult the Quick Start card that shipped with your computer to make sure you received everything.

If any items are missing or damaged, contact your authorized Toshiba representative or your network administrator.

Finding where everything is located

The next few pages take you on a guided tour of your computer.

Page 39

Finding Your Way Around

Finding where everything is located

Front with the display panel closed

Wireless antenna on/off switch*

Display latch

Infrared port

Headphone jack

Microphone jack

Infrared port—The fast infrared port allows cable-free communication with another device, such as a computer or printer, that has a compatible infrared port.

Wireless antenna on/off switch—The Wireless antenna on/ off switch turns the optional wireless communication system on or off.

Microphone jack—The 3.5 mm microphone jack lets you connect an external monaural microphone or other audio input device. Connecting a microphone or other device to this jack automatically disables the internal microphone.

Headphone jack—The 3.5 mm headphone jack lets you connect stereo headphones or other audio output devices. Connecting headphones or other devices to this jack automatically disables the internal speakers.

Display latch—Sliding the display latch opens the computer display panel. For more information, see “Front with the

display panel open” on page 43

System indicator panel—The system indicator panel is made up of several status lights that provide information about various system functions. See “System indicator panel

lights” on page 46 for a description of each of the panel

lights.

System indicator panel

* functional only on systems with a

wireless module installed

Page 40

Back

Finding Your Way Around

Finding where everything is located

RGB (monitor) port

USB 2.0 ports

DC IN

PS/2 port

Parallel port

Serial port

Modem port

Network port

USB ports—Use the Universal Serial Bus 2.0 (USB) ports to connect USB peripherals.

DEFINITION: USB 2.0 is a peripheral expansion standard that supports a data transfer rate of up to 480 Mbps for peripherals such as keyboards and pointing devices. USB peripherals have a single standard for cables and connectors. The USB standard also allows hot swapping of peripherals.

DC IN—Lets you plug in the AC adapter.

™

PS/2

port—Lets you connect an optional PS/2-compatible

mouse or keyboard. You can use an optional Y-cable to connect both a mouse and a keyboard to the port.

Ether

RGB (monitor) port—Lets you connect an external monitor or projector. For more information, see “Using external

display devices” on page 64.

Serial port—Lets you connect a serial mouse, serial printer, or other serial device.

Parallel port—Lets you connect a parallel printer or other parallel device. For more information, see “Connecting a

local printer” on page 70.

Network port—Lets you connect the computer to an Ethernet LAN (local area network).

Page 41

Left side

Finding Your Way Around

Finding where everything is located

Modem port—Lets you connect the computer’s internal modem directly to a conventional telephone line.

Volume control dial

SD indicator

SD Card slot

PC card ejection buttons

Cooling Vents

Video-out port

Speaker

Security lock slot

PC card slots

Speaker—Lets you hear stereo sound from a CD or DVD, in addition to system alarms and audible warnings associated with your software.

Security lock slot—Attaching an optional PORTNoteworthy

Computer Lock Cable to the security lock slot lets you anchor your computer to a large, heavy object such as your desk. For more information, see “Using a computer

lock” on page 111.

PC Card slots—Allows you to use Type I, Type II, or Type III PC Cards.

card slot—Lets you insert SD® cards for additional data

storage.

indicator—The SD® slot indicator light glows when the

card is being accessed. The SD® slot is located on the left

SD side of the computer.

Video-out port—Lets you connect your computer to an external video device, such as a standard television set.

Volume control dial—The volume control dial lets you adjust the loudness of the system speakers.

Page 42

Cooling vent—Provides ventilation to keep the computer’s processor from overheating. The vent lets the processor continue performing at its maximum speed.

Right side

Finding Your Way Around

Finding where everything is located

To prevent possible overheating of the computer’s processor, make sure you do not block the cooling vent.

Speaker

Slim SelectBay module (DVD-ROM drive shown)

Speaker—Lets you hear stereo sound from a CD or DVD in addition to system alarms and audible warnings associated with your software.

Slim SelectBay

SelectBay modules. The DVD-ROM drive is shown in place. For more information on using your DVD-ROM, see “Using

the DVD-ROM or multi-function drive” on page 104. For

further information on Slim SelectBay devices, see “Using

Slim SelectBay® modules” on page 77.

— Lets you use one of several possible Slim

USB 2.0 port

Page 43

Finding Your Way Around

Finding where everything is located

USB port—Use the Universal Serial Bus 2.0 (USB) ports to connect USB peripherals.

Front with the display panel open

To view the front of the computer with the display panel open:

1 Locate the display latch on the front of the computer.

2 Slide the display latch to the right and lift the display

panel.

3 Adjust the display panel to a comfortable viewing angle.

To avoid damaging the display panel, be careful when opening and closing it. Never force the panel beyond the point where it moves easily, and never use it to lift the computer.

Page 44

Power button

Finding Your Way Around

Finding where everything is located

Screen

Keyboard

Speaker

CapsLock indicator

AccuPoint II pointing device

Wireless antenna switch

Power button —The power button is used to turn on power to the computer. For more information, see “Turning on the

computer” on page 58.

Screen—The computer’s screen is a liquid crystal display (LCD) that provides clear, sharp images.

Keyboard—The 85-key keyboard provides all the functionality of a full-size keyboard. For more information, see “Using the keyboard” on page 89.

Keyboard indicator panel—These lights provide information about various keyboard functions. See

“Keyboard indicator panel lights” on page 47 for a

description of the panel lights.

System indicator panel

To uc hP ad buttons

Speaker

Keyboard indicator panel

AccuPoint buttons

TouchPad

Microphone

Wireless antenna switch— Turns the computer’s wireless antenna on or off.

AccuPoint

II pointing device—This device combines the

function of a mouse with the convenience of never having to

Page 45

remove your hands from the keyboard. See “Setting up your

software” on page 60.

Tou chP ad —The small, smooth square cutout located in front of the keyboard is sensitive to touch and enables you to move the cursor with the stroke of a finger. Simply move your finger on the TouchPad in the direction you’d like to move the cursor. See “Using the TouchPad™” on page 95.

System indicator panel—These lights provide status information about various system functions. See “System

indicator panel lights” on page 46 for a description of each

panel light.

Internal microphone—The 3.5 mm microphone lets you connect an external monaural microphone or other audio input device.

Underside

Finding Your Way Around

Finding where everything is located

Hard disk drive bay

Battery module—Lets you to use your computer when a standard electrical outlet is not available. For further

Memory module cover

Battery module

Battery module release

Slim SelectBay release

Slim SelectBay slot

Expansion port

Page 46

Finding Your Way Around

Indicator panel lights

information about using the battery, see “Mobile Computing”

on page 123.

Slim SelectBay release—Keeps the Slim SelectBay module secure in its compartment.

Memory module cover—Lets you add more memory to your computer. For more information, see “Ad d in g m e mo ry ”

on page 73.

Slim SelectBay slot—One of several interchangeable devices which offer exceptional system flexibility. For more information, see “Using Slim SelectBay® modules” on

page 77.

Expansion port—Lets you connect to an expansion device, provides additional expansion capability. For more information, see “Using an expansion device” on page 73.

Indicator panel lights

Two sets of indicator lights, the system indicator panel and the keyboard indicator lights, display the current state of your system.

System indicator panel lights

This panel is located on the front of the computer.

AC power light—Glows green when the computer is connected to an AC power source.

On/off light—Indicates whether the computer is on, off, or in a power down mode.

❖ Glows green when the computer is on.

❖ Flashes amber when you power down the computer using

the Standby command.

Page 47

Finding Your Way Around

Indicator panel lights

❖ May flash amber if the computer is overheating.

Main battery light—Indicates the status of the main battery.

❖ Flashes amber when you are running on battery power

and the battery charge is running low.

❖ Does not glow when you are running on battery power

and the battery charge is not running low.

❖ Glows amber when you are connected to AC power and

the battery is charging.

❖ Glows green when you are connected to AC power and

the battery is fully charged.

For more information, see “Monitoring battery power” on

page 126.

Hard disk drive light—Flashes to indicate that the hard disk is currently in use.

Slim SelectBay indicator light—Indicates when the optical drive is being accessed. Also indicates the status of a secondary battery in the Slim SelectBay, if installed.

❖ Glows amber when the battery is charging.

❖ Glows green when the battery is fully charged.

❖ Does not glow if there is no battery in the Slim

SelectBay.

Wireless indicator light—Glows amber to indicate that wireless antenna on/off switch is on.

Keyboard indicator panel lights

The keyboard indicator lights provide information about keyboard functions.

Caps lock light—Glows when you press the caps lock key. When this light is on, pressing a letter key on the keyboard produces an uppercase (capital) letter. The caps lock key does not affect the number and symbol keys.

Page 48

Finding Your Way Around

Indicator panel lights

Cursor control light—Glows when the cursor control overlay is on. When this light is on, pressing an overlay key moves the cursor as shown by the white arrow or command printed on the left front of the key instead of the letter printed on the top of the key. For more information, see “Using the

overlay for cursor control” on page 93.

Numlock light—Glows when the numeric overlay is on. When this light is on, pressing an overlay key produces the white number printed on the right front of the key instead of the letter printed on the top of the key. For more information, see “Using the overlay to type numeric data” on page 92.

Page 49

Chapter 2

Getting Started

This chapter provides tips for working comfortably, describes how to connect components, and explains what to do the first time you use your computer.

Selecting a place to work

Your computer is designed to be used in a variety of locations and situations. This section provides guidelines for setting up your computing environment.

Creating a computer-friendly environment

Place the computer on a flat surface that is large enough for the computer and any other items you need to use, such as a printer. Leave enough space around the computer and other equipment to give adequate ventilation, otherwise, they may overheat.

Page 50

Getting Started

Selecting a place to work

To keep your computer in prime operating condition, protect your work area from:

❖ Dust, moisture, and direct sunlight.

❖ Liquids and corrosive chemicals.

If you spill liquid into the computer, turn it off, unplug it from the AC power source, and let it dry out completely before turning it on again.

If the computer does not operate correctly after you turn it back on, contact a Toshiba Authorized Service Provider.

❖ Equipment that generates a strong electromagnetic field,

such as large stereo speakers (other than speakers that are connected to the computer) or speakerphones.

❖ Rapid changes in temperature or humidity and sources of

temperature change such as air conditioner vents or heaters.

❖ Extreme heat, cold, or humidity. Operate the computer

within a temperature range of 41 degrees to 95 degrees Fahrenheit (5 degrees to 35 degrees Celsius) and 20 percent to 80 percent non-condensing humidity.

Keeping yourself comfortable

Strain and stress injuries are becoming more common as people spend more time using their computers. However, with a little care and proper use of the equipment, you can work comfortably throughout the day.

Using the computer keyboard incorrectly can result in discomfort and possible injury. If your hands, wrists, and/or arms hurt while typing, stop using the computer and rest. If the discomfort persists, consult a physician.

Page 51

Getting Started

Selecting a place to work

This section provides hints on avoiding strain and stress injuries. For more information, consult books on ergonomics, repetitive-motion injury, and repetitive-stress syndrome.

Placement of the computer

Proper placement of the computer and external devices is important to avoid stress-related injuries. Consider the following when placing your computer.

❖ Place the computer on a flat surface at a comfortable

height and distance. You should be able to type without twisting your torso or neck and look at the screen without slouching.

❖ If you use an external monitor, the top of the screen

should be no higher than eye level.

❖ If you use a paper holder, set it at the same height and

distance as the screen.

Seating and posture

When using your computer, maintain good posture with your body relaxed and your weight distributed evenly. Proper seating is a primary factor in reducing work strain. Some people find a backless chair more comfortable than a conventional chair. Whichever type you choose, use the following guidelines to adjust your chair for maximum computing comfort.

Page 52

Getting Started

Selecting a place to work

Below eye level

Approximately 90° angles

Footrest

Correct posture and positioning of the computer

❖ Position your chair so that the keyboard is at or slightly

below the level of your elbow. You should be able to type comfortably with your shoulders relaxed and your forearms parallel to the floor.

If you are using a conventional chair:

❖ Your knees should be slightly higher than your hips. If

necessary, use a footrest to raise the level of your knees and ease the pressure on the back of your thighs.

❖ Adjust the back of your chair so that it supports the lower

curve of your spine. If necessary, use a cushion to provide extra back support. Lower-back support cushions are available at many office supply stores.

❖ Sit with your back straight so that your knees, hips, and

elbows form approximately 90-degree angles when you work. Do not slump forward or lean back too far.

Lighting

Proper lighting can improve the readability of the display and reduce eyestrain.

❖ Position the display panel or external monitor so that

sunlight or bright indoor lighting does not reflect off the screen. Use tinted windows or shades to reduce glare.

Page 53

Getting Started

Other precautions

❖ Avoid placing your computer in front of a bright light that

shines directly into your eyes.

❖ If possible, use soft, indirect lighting in your computer

work area.

Arms and wrists

❖ Avoid bending, arching, or twisting your wrists. Keep

them in a relaxed, neutral position while typing.

❖ Exercise your hands, wrists, and arms to improve

circulation.

Work habits

The key to avoiding discomfort or injury from strain is to vary your activities. If possible, schedule a variety of tasks into your working day. Finding ways to break up the routine can reduce stress and improve your efficiency.

❖ Take frequent, short breaks to change position, stretch

your muscles, and relieve your eyes. A break of two or three minutes every half hour is more effective than a long break after several hours.

❖ Avoid performing repetitive activities for long periods.

Intersperse such activities with other tasks.

❖ Focusing your eyes on your computer screen for long

periods can cause eyestrain. Look away from the computer frequently and focus your eyes on a distant object for at least 30 seconds.

Other precautions

Your computer is designed to optimize safety, minimize strain, and withstand the rigors of portability. However, you

Page 54

Getting Started

Other precautions

should observe certain precautions to further reduce the risk of personal injury or damage to the computer.

Do not apply heavy pressure to the computer or subject it to sharp impacts. Excessive pressure or impact can damage computer components or cause your computer to malfunction.

Some PC Cards can become hot with prolonged use. If two cards are installed, both can become hot even if only one is used extensively. Overheating of a PC Card can result in errors or instability in the PC Card operation.

Be careful when you remove a PC Card that has been used for lengthy periods of time.

Setting up your computer

TECHNICAL NOTE: You must complete all set up steps up to

“Setting up your software” on page 60 before adding external

or internal components to your computer. These components include, but are not limited to, a mouse, keyboard, printer, memory, and PC cards.

Your computer comes with a rechargeable battery pack that must be charged before you can use it.

To use external power or to charge the battery, you must attach the AC adapter. See “Connecting the AC adapter” on

page 55.

To register your computer online, or to sign up for an Internet account, you must connect the built-in modem to a telephone line.

Page 55

Getting Started

Other precautions

Before adding any of these devices to the computer, be sure to complete “Setting up your software” on page 60.

After setting up your computer, you may want to:

❖ Add more memory. See “Adding memory” on page 73

❖ Connect a mouse. See “Using a mouse” on page 69

❖ Connect a full-size keyboard. See “Using an external

keyboard” on page 68

❖ Connect an external monitor. See “Using external display

devices” on page 64

❖ Connect a local printer. See “Connecting a local printer”

on page 70

❖ Install PC Cards. See “Inserting and removing PC Cards”

on page 82

For more information on installing specific devices, see

“Connecting Other External Devices” on page 64.

Connecting the AC adapter

Your computer requires power to operate. Use the power cable and AC adapter to connect the computer to a live electrical outlet, or to charge the computer’s battery.

Power cable

Sample power cable and AC adapter

Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling.

AC adapter

Page 56

Getting Started

Other precautions

Use only the AC adapter supplied with your computer or an equivalent adapter that is compatible. Use of any incompatible adapter could damage your computer. Toshiba assumes no liability for any damage caused by use of an incompatible adapter.

When you connect the AC adapter to the computer, always follow the steps in the exact order as described in the User's Manual. Connecting the power cable to a live electrical outlet should be the last step otherwise the adapter DC output plug could hold an electrical charge and cause an electrical shock or minor bodily injury when touched. As a general safety precaution, avoid touching any metal parts.

Hold the power cable by its plug when you connect/disconnect it. Do NOT pull the cable itself. Doing so may damage the power cable and result in a short circuit or electric shock.

To connect AC power to the computer:

1 Connect the power cable to the AC adapter.

Connecting the power cable to the AC adapter

2 Plug the AC adapter into DC IN on the rear of the

computer.

Page 57

Getting Started

Other precautions

Connecting the AC adapter to the computer

3 Connect the power cable to a live electrical outlet.

If the electrical outlet is live, the system indicator panel’s AC power light ( ) glows green.

If the main battery is present, the battery light glows:

❖

Amber while the battery is charging

❖ Green when the battery is fully charged

If the battery light flashes amber during charging, either the battery pack is malfunctioning, or it is not receiving input from the AC power supply. Disconnect the AC cable and remove the battery pack. See “Contacting Toshiba” on

page 211.

Damaged power cables can cause fire or electric shock. Never modify, forcibly bend, place heavy objects on top of, or apply heat to the power cable.

If the power cable becomes damaged or the plug overheats, discontinue use. There is a risk of electric shock.

Never remove the power plug from the outlet with wet hands. Doing so may cause an electric shock.

Page 58

Getting Started

Turning on the computer

Charging the battery

Before you can use the battery to power the computer, you must charge it. Connect the computer to a live electrical outlet using the AC adapter and power cable. When the AC adapter is connected to a live electrical outlet, the system indicator panel’s AC power light ( ) glows green and the battery light ( ) glows amber. When the battery light turns green, the battery is completely charged and ready to power the computer.

Charging time for the battery varies depending upon the demand placed on the AC adapter. If the computer is off, the battery should fully charge in about three hours. If the computer is on, the battery will charge in four to ten hours, provided the computer is not consuming full power. If you are also charging a secondary battery housed in the Slim SelectBay, charging time will be longer.

NOTE

For more information on battery use, see “Running the

computer on battery power” on page 123.

Once the battery is charged for the first time, avoid leaving the computer plugged in and turned off for more than a few hours at a time.

Turning on the computer

The computer is now ready for you to turn it on and begin using it.

Opening the display panel

1 Slide the display latch to the right.

Page 59

2 Lift the display panel.

To avoid damaging the display panel, do not force it beyond the point where it moves easily, and never lift the computer by the display panel.

Small bright dots appear on your TFT display when you turn on your computer. Your display contains an extremely large number of thin-film transistors (TFT) and is manufactured using high-precision technology. Any small bright dots that appear on your display are an intrinsic characteristic of the TFT manufacturing technology.

Turning on the power

To turn on the computer:

1 Make sure any external devices (such as the AC adapter, if

you plan to use AC power rather than battery power) are properly connected and ready.

Getting Started

Turning on the computer

2 Check to ensure that any floppy drives are empty.

3 Press and hold the power button in until the on/off light

on the system indicator panel glows green—about one second.

Turning on the power

Page 60

Getting Started

Setting up your software

For the meaning of each light on the system indicator panel, see “System indicator panel lights” on page 46.

4 The preinstalled operating system will load

automatically.

When you turn on the computer for the first time, do not turn off the power again until the operating system has loaded completely.

Setting up your software

NOTE

The first time you turn on your computer, the Setup Wizard guides you through steps to set up your software.

1 From the welcome screen, click Next to enter the Setup

2 Confirm acceptance of Microsoft’s End User License

3 Enter the computer name and description and click Next

The name of the windows displayed and the order in which windows appear may vary according to your software setup choices.

Wizard.

Agreement and click Next.

or Skip.

The computer will pause for a moment while checking for an Internet connection.

A window will display the message: “An Internet connection could not be chosen.”

Page 61

Getting Started

Registering your computer with Toshiba

4 Click Skip to exit the process or Next to continue.

NOTE

5 Click Ye s to register, or No to exit the process.

NOTE

6 Enter your personal information in the registration

7 Click Finish to complete the process.

To register online, your computer’s modem must be connected to a voice-grade telephone line.

A window will ask whether you want to register with Toshiba or Microsoft.

If you click No, you can register with Toshiba by clicking the Register with Toshiba icon on the desktop.

window.

Your computer restarts automatically.

Registering your computer with Toshiba

To register your computer with Toshiba, you may either click on the desktop icon to do so electronically, or fill in and mail the registration card that shipped with your system.

Setting up other devices

You may want to take this time to set up your printer. For more information, see “Connecting a local printer” on

page 70.

Page 62

Getting Started

Turning off the computer

It’s generally a good idea to turn off your computer when you are not using it.

If you are using the computer for the first time, leave the computer plugged into a power source (even though the computer is off) to fully charge the main battery. With the computer off, it may take up to three hours to recharge the main battery.

When you power down the computer, you have three options to choose from: Turn Off (or Shut down), Hibernate or Standby. Each option has its advantages.

❖ Use the Turn Off command if you are using the Windows

XP Home operating system, or the Windows® XP Professional operating system when not connected to a domain server.

❖ Use the Shut down command if you are using the

Windows connected to a domain server.

XP Professional operating system and

❖ If you have work in progress and are not connected to a

network, use the Windows commands to save your system settings to the hard drive so that, when you turn on the computer again, you will automatically return to where you left off.

❖ To leave the computer off for a longer period, you can use

the Windows a domain server or the Shut down command when connected to a domain server instead. For more information, see “Powering down the computer” on

page 113.

Never turn off the computer while any drive is in use. Doing so may damage the media in use and result in loss of data.

Turn Off command when not connected to

Standby or Hibernate

Page 63

Closing the display panel

When you are finished, shut the computer down and close the display panel to keep dust and dirt out of the computer.

If you close the computer while it is still on, these actions will occur:

❖ If you have the LCD power-saver feature set, the LCD

panel will automatically turn off until you open it again.

❖ If you have the audible warning set, the computer will

beep to notify you that it is still on.

❖ If you have an action feature set, the computer will

perform either: Nothing, Standby, or Hibernate (see

“Using Hibernation” on page 117).

Getting Started

Turning off the computer

Page 64

Chapter 3

Connecting Other External Devices

This chapter describes how to connect devices that can increase the capabilities of your Satellite computer.

Using external display devices

Your computer comes with a built-in LCD display, but you can also connect three different types of external display devices to one of two available video ports:

❖ A television via the video-out (composite) port.

❖ A video display device, such as a video projection unit,

via the video-out (composite) port.

❖ An external monitor or projector via the RGB (monitor)

port.

Connect a television, video projector, monitor or other display device and then configure your computer for the type of device you’re connecting. To do this, refer to the documentation for your operating system and devices.

Connecting the display device

If you’re connecting a television or other video display device to the computer’s video-out port, first refer to “Selecting

Page 65

Connecting Other External Devices

Using external display devices

video cables” below for guidelines on choosing a video cable,

then refer to “Connecting to the video-out (composite) port”

on page 65.

If you’re connecting an SVGA monitor, skip to “Connecting

an external monitor or projector” on page 66.

Selecting video cables

To connect a device to the video-out port, you’ll need to purchase a composite video cable. For the best video quality, always use a properly shielded cable.

HINT: Toshiba recommends using a cable no longer than 20 feet (approximately 6 meters).

Using a poor quality cable may result in a dull or fuzzy picture, poor color, ghosting, video noise, or loss of video.

Connecting to the video-out (composite) port

NOTE

1 Connect one end of the video cable to the external video

2 Connect the other end of the video cable to the video-out

3 Turn on the external video device.

4 Set the display mode by pressing

Video cables are not included with your computer. To connect a device to the video-out port, you’ll need to purchase a composite video cable.

device.

Refer to the documentation provided with the device for the location of its video-in port.

port on the left side of the computer.

Fn + F5, or by setting the

Display Properties settings. For more information, see

Page 66

Connecting Other External Devices

Using external display devices

“Directing the display output when you turn on the computer” on page 66.

Connecting an external monitor or projector

You can easily attach an external monitor or projector to your computer if you need a larger screen. To do this:

1 Connect the monitor’s video cable to the RGB port on the

back of the computer.

2 Connect the device’s power cable to a live electrical

outlet.

3 Turn on the external device.

4 Set the display mode by pressing

Display Properties settings. For more information, see

“Directing the display output when you turn on the computer” on page 66.

Fn + F5, or by setting the

Directing the display output when you turn on the computer

Once you’ve connected an external display device, you can choose to use the internal display only, the external device only, or both simultaneously. The quickest way to change the display output settings is to use the display hot key (

1 While holding down

you want takes effect.

This hot key cycles through the settings in the following order:

❖ Built-in display only

❖ Built-in display and external device simultaneously

❖ External device only

❖ Built-in display and TV (or other external video device)

simultaneously

Fn, press F5 repeatedly until the setting

Fn + F5):

❖ TV (or other external video device) only

Page 67

Connecting Other External Devices

Using external display devices

2 Release the Fn key.

TECHNICAL NOTE: You can also change these settings using the Display Properties Box.

For more information on switching the display output, see

“Display modes” on page 244.

Adjusting the quality of the external display

To obtain the best picture quality from your television (or other video display device), you may need to adjust the video settings. See the video device documentation for additional configuration steps.

TECHNICAL NOTE: In order to use one of the simultaneous modes, you must set the resolution of the internal display panel to match the resolution of the external display device. The external display device must support a resolution of 640 X 480 or higher.

Video limitations

Keep in mind that the quality of the display will be limited to the capabilities of the external video device.

❖ If the external video device, such as an SVGA monitor, is

capable of displaying at a maximum resolution of 640 x 480 and your system is set for a higher resolution, only part of the desktop will appear on the screen. You can view the “lost” area by scrolling to it.

❖ Since most televisions and video projectors overscan by

15 to 20 percent, some of the desktop will be outside the viewing area. You can view the edge of the desktop by scrolling to it.

Page 68

Connecting Other External Devices

Using an external keyboard

If you prefer to use a full-size keyboard, you can attach one to your computer. The computer’s PS/2 port supports any PS/2compatible keyboard.

NOTE

If you connect a PS/2 keyboard to the computer while it is in Standby/Hibernation mode, you will not be able to use the keyboard when you turn the computer on.

When connecting or disconnecting any PS/2 device, turn off your computer to prevent any possible hardware damage.

HINT: You can only connect one PS/2 device at a time, unless you purchase an optional Y-cable. Connecting a Y-cable to the computer’s PS/2 port allows you to connect a PS/2compatible mouse and a PS/2-compatible keyboard simultaneously.

Page 69

Connecting Other External Devices

Using a mouse

Making your external keyboard emulate the Fn key

An external keyboard does not have the Fn key contained on the Satellite computer’s built-in keyboard. If you use the computer’s hot keys or have set up key combinations in Fn-esse external keyboard. Do not worry: you can use a key combination on the external keyboard to emulate the You can set up this key combination through the Windows Control Panel Toshiba Hardware Setup option icon. For more information about Hardware Setup, see “Toshiba HW Setup”

on page 164.

, you’ll probably miss these features when using an

Using a mouse

You may want to use a mouse instead of the computer’s builtin pointing device, the AccuPoint II or TouchPad. You can use a serial mouse, a PS/2-compatible mouse, or a USB mouse.

Fn key.

Setting up a PS/2 mouse with the AccuPoint II

When you connect a PS/2-compatible mouse to the PS/2 port, you may use the mouse, the AccuPoint II, or both.

When connecting any PS/2 device, turn off your computer to prevent any possible hardware damage.

NOTE

To set the PS/2 mouse to work simultaneously with the AccuPoint II:

1 Click Start, then Control Panel.

If you connect a PS/2 mouse to the computer while it is in Standby mode, you will not be able to use the mouse when you turn the computer on.

Page 70

Connecting Other External Devices

Connecting a local printer

2 Click Pointers and Other Hardware.

3 Double-click the Tos hib a HW Setup icon.

4 Select the Pointing Devices tab, then click

Simultaneous.

Connecting a local printer

NOTE

Read the documentation that came with your printer. Follow the manufacturer’s instructions when connecting a local printer.

You must supply the proper printer cable. If one did not come with your printer, you may purchase one from an electronics or computer store.

If your printer is ECP- or IEEE-compliant, make sure your printer cable is an IEEE 1284 cable.

Your printer documentation may require you to install the printer software before physically connecting the printer to your computer. If you do not install the software as instructed by the printer manufacturer, the printer may not function correctly.

Never connect the printer cable while the computer’s power is on. Doing so may damage the printer, the computer, or both.

These instructions assume you have a parallel printer.

To connect the printer:

Page 71

Connecting Other External Devices

Connecting an external diskette drive

1 If the computer is on, turn it off.

2 Connect the printer cable to the printer and to the

computer’s parallel port. Use the printer cable illustration as a connection guide.

To the computer To the printer

Identifying the ends of a parallel printer cable

3 Plug the printer’s power cable into a live electrical outlet.

4 See your printer documentation for additional

configuration steps.

For more information on getting your printer to print, see

“Printing your work” on page 103.

Connecting an external diskette drive

Some operations, such as creating a password service diskette, require a diskette drive designed for use with 3.5inch diskettes.

An optional external USB diskette drive

To connect an optional external USB diskette drive, connect the cable to one of the USB ports.

Page 72

Connecting Other External Devices

Connecting external speakers or headphones

Connecting an optional external USB diskette drive

Connecting external speakers or headphones

To attach an external stereo output device:

1 Locate the headphone jack on the front of the computer.

2 Using any necessary adapters, plug the cable from the

external audio device into the headphone jack. The headphone jack requires a 3.5 mm 16-ohm stereo jack.

When the headphone is inserted, the internal speakers are automatically disabled.

For more information on using headphones or external speakers, see “Using external speakers or headphones” on

page 142.

Connecting an external microphone

Your computer comes equipped with an internal microphone, but to record higher quality sounds, you can attach an external microphone:

1 Locate the microphone jack on the front of the computer.

2 Plug the microphone cord into the microphone jack.

3 Turn on the microphone.

Page 73

Connecting Other External Devices

Using an expansion device

The internal microphone is automatically disabled.

Once the external microphone is connected, the recording process is the same as with the built-in microphone. For more information, see “Recording sounds” on page 143.

Using an expansion device

The expansion port allows you to connect your computer to an expansion device, which is an excellent investment if you’re using your computer both in and out of the office.

When you return to your desk, you probably want to connect to your network, print reports from your computer, or use a mouse instead of the AccuPoint II. Connecting cables for each of these devices every time you return to the office is time-consuming and inconvenient.

With an expansion device, you can leave external devices connected while you are using your computer away from your desk. When you return, you can quickly connect your computer and have immediate access to all the devices.

For more information, see the accessories information package that comes with the device or visit

Adding memory

HINT: To purchase additional memory modules, see the accessories information packaged with your system or visit

toshiba.com.

Your Satellite computer is equipped with two memory slots which can provide for various memory configurations. When additional memory is added, or original memory replaced, it is recommended that you use only compatible memory. In the event original memory is replaced with invalid memory, the system will beep and will not boot beyond the BIOS memory

www.toshiba.com.

Page 74

Connecting Other External Devices

Adding memory

check. A message may display. If this occurs, contact Toshiba’s support center at (800) 457-7777.

Since your computer was built to order, it should have enough memory to run your current applications. However, if your requirements change, you can install extra memory.

Installing a memory module

Additional memory modules can be installed in the memory expansion slots on the base of the computer. You will need a standard Phillips no.1 screwdriver for this procedure.

To avoid damaging the computer’s screws, use a standard Phillips no. 1 screwdriver that is in good condition.

The computer has one memory expansion slot. You can install one memory module.

1 Shut down your computer completely using the Shut Down

command. See “Turning off the computer” on page 62.

2 Unplug the computer.

Installing a memory module with the computer’s power on may damage the computer, the module, or both.

3 Close the display panel and remove any cables you may

have connected.

4 Remove the battery.

5 Turn the computer upside down.

6 Locate and remove the screw that holds the cover plate in

place, and lift the cover off of the memory module bay.

Page 75

Connecting Other External Devices

Removing the memory module cover

Static electricity can damage the memory module. Before you handle the module, touch a grounded metal surface to discharge any static electricity you may have built up.

To avoid damaging the memory module, be careful not to touch its pin connector on the side you insert into the computer.

Adding memory

7 Remove the new memory module from its antistatic

packaging.

8 Insert the memory module in the slot and gently press it

down into place.

The clips on either side of the module will click to secure the module.

Page 76

Connecting Other External Devices

Adding memory

Inserting the memory module into the slot

9 Replace the cover plate and the screw.

10 Turn the computer over and restart it.

When you turn on the computer, it automatically recognizes the additional memory.

Removing a memory module

If you need to remove a memory module:

1 Complete steps 1–5 in “Installing a memory module” to shut

down the computer and open the memory module cover.

2 Pull the clips away from the memory module.

The memory module pops partially out of the slot.

Page 77

Connecting Other External Devices

Using Slim SelectBay® modules

Removing the memory module

3 Carefully remove the module from the slot.

4 Replace the cover plate and screws.

5 Turn the computer over and restart it.

Using Slim SelectBay® modules

The Slim SelectBay® gives you additional flexibility. By inserting and removing Slim SelectBay® modules, you can configure your computer for the task at hand without having to carry unnecessary components with you when you travel. For example, any one of several modules can be used in the Slim SelectBay®:

❖ DVD-ROM drive. The DVD-ROM drive can also be used

as a standard CD-ROM drive.

❖ Multi-function drive

❖ Weight saver insert (a “honeycomb” piece of plastic) that

reinforces the Slim SelectBay saver came in your computer’s accessories box.

❖ Secondary battery

for travel. The weight

Page 78

Connecting Other External Devices

Using Slim SelectBay® modules

❖ Secondary hard disk drive (HDD)

HINT: Items from this list that did not come with your computer can be purchased separately. See the accessories information packaged with your system or visit

www.toshibaaccessories.com.

Removing a module from the Slim SelectBay

NOTE

1 Turn off the computer.

2 Slide the Slim SelectBay

Use caution when lifting or turning your computer. Failure to do so may result in damage to components, such as cables, attached to your computer, or to the computer itself.

You may also hot swap a module in the Slim SelectBay. Stop the module by clicking the Safely Remove Hardware icon on the System tray. After the module is stopped, it is safe to remove.

release toward the rear of the

computer.

Page 79

Connecting Other External Devices

Using Slim SelectBay® modules

Unlatching the Slim SelectBay

3 Slide the module out of the computer.

Sliding the module out

If you are removing the weight saver, retain it for transporting the computer when no other module is installed in the

Slim SelectBay

Inserting a module into the Slim SelectBay

To install a module into the Slim SelectBay®, simply slide the module all the way into the Slim SelectBay

Page 80

Connecting Other External Devices

Inserting and removing hard drives

Your Tecra® S1 can use various hard drive capacities. Depending upon the original hard drive installed in your computer, you may wish to increase storage capacity by changing the internal drive, or you can also add additional hard drive space by inserting a drive into the select bay module.

To change the internal hard drive.

1 Shut down your computer completely using the Shut Down

command. See “Turning off the computer” on page 62.

2 Unplug the computer.

3 Close the display panel and remove any cables you may

have connected.

4 Turn the computer upside down and remove the battery.

5 Remove the screw on the hard drive bay cover.

Removing the hard drive cover screws

6 Lift the hard drive bay cover to expose the hard drive.

7 Grasp the plastic tab on the exposed edge of the hard

drive and pull it to remove the hard drive from the computer.

Page 81

Connecting Other External Devices

Inserting and removing hard drives

Removing the hard drive from the computer

8 Pull the clips off of the old hard drive and remove the

cover.

Removing the cover

9 Snap the cover onto the new hard drive.

Snapping the cover onto the new hard drive

10 Install the new hard drive by sliding it into the hard drive

bay and pressing it firmly until it locks. Do not force the drive into the computer.

Page 82

Connecting Other External Devices

Inserting and removing PC Cards

Inserting the new hard disk drive

11 Replace the hard drive bay cover and tighten the screw

removed in step 5 above.

Inserting and removing PC Cards

Your Satellite computer comes with two stacked PC Card slots and supports three types of PC Cards:

❖ Type I cards—You can install up to two of these cards,

one in each slot.

❖ Type II cards—You can install up to two of these cards,

one in each slot.

❖ Type III cards—You can install just one of these cards.

Inserting a PC Card

Before you insert a PC Card, refer to the documentation that comes with the card to see if you need to do anything before you insert it.

Page 83

Connecting Other External Devices

Inserting and removing PC Cards

There are three different ways to insert a PC Card:

❖ Turn off the computer and follow the steps below.

❖ Insert the PC card while the computer is running. Follow

the steps below.

❖ Hot swap the card (choose this method if there is already

a PC Card in slot you wish to use). Stop the PC Card by clicking the Safely Remove Hardware icon on the System tray. After the PC Card is stopped, it is safe to remove it. Follow the steps below.

1 Locate the PC Card slot on the left side of the computer.

2 Insert the PC Card.

If you have a Type III card, insert it into the lower part of the slot. If you have a Type I or Type II card, insert it into either the upper or lower part of the slot.

Inserting a PC Card

3 When the card is almost all the way into the slot, push

firmly, but gently, to ensure a firm connection with the computer. Do not force the card into position.

Removing a PC Card

1 Stop the PC Card by clicking the Safely Remove Hardware

icon on the System tray. After the PC Card is stopped, it is safe to remove it.

Page 84

Connecting Other External Devices

Inserting an SD® card

2 Locate the PC Card ejection button that corresponds to

the slot in which your PC Card is installed.

The top tab releases a card in the upper slot. The bottom tab releases a card in the lower slot.

3 Press the PC Card eject button once to extend it, and push

it in to remove the PC Card.

Press the PC card ejection button once to extend it

The PC Card ejects slightly from the slot.

4 Grasp the edges of the PC Card and slide it out of the

slot.

Setting up a PC Card for your computer

Some PC Cards are ready to use as soon as you install them. Others, such as hard disk cards, network cards and SCSI adapters, may need to be set up to work with your computer. To set up your PC Card, refer to the documentation that came with the card or refer to your operating system manual or online help.

Inserting an SD® card

To insert an SD® card, turn the card so that the connector (metal area) faces down, then push the card in the slot until it locks in place.

Page 85

Connecting Other External Devices

Connecting your modem to a telephone line

If Windows® does not recognize an inserted SD® card, remove and insert it again.

To remove an SD the card will pop out slightly.

The green LED on the left side of the computer will glow when the card is being accessed.

Do not touch the SD® connector. You could expose the storage area to static electricity which can destroy data.

Do not remove an SD Even when the message “copying...” in the windows disappears, the computer may be writing to the computer and your data could be destroyed. Wait for the SD to go out.

card, press the card inward to release it and

card while data is being written or read.

indicator light

NOTE

Your computer’s SD® card slot does not work with multimedia cards.

Connecting your modem to a telephone line

Your computer comes with a built-in modem that can be connected to a standard voice-grade telephone line.

The modem allows you to:

❖ Access the Internet.

❖ Communicate with your office’s local area network

(LAN), or a larger corporate wide area network (WAN).

For specific information about connecting to a LAN or WAN, consult your network administrator.

❖ Send a fax directly from your computer.

Page 86

Connecting Other External Devices

Connecting your modem to a telephone line

Connecting to a phone line

Before you can communicate using the modem, you need to connect it to a telephone line. Your computer’s built-in modem port provides an RJ-11 jack, allowing you to connect the modem to a standard voice-grade telephone line.

1 Plug one end of the telephone cable into the modem port on

the back of the computer.

Connecting the telephone cable to the modem port

2 Connect the other end to the RJ-11 wall jack.

Page 87

Connecting Other External Devices

Connecting your modem to a telephone line

Connecting to a wall jack

The modem is designed for use with a standard analog telephone line. Do not connect the modem to a digital telephone line. A digital line will damage the modem.

Now you’re ready to send a fax or use the modem to connect to an online service or the Internet.

For more information on using a modem, see “Setting up for

communications” on page 146.

Page 88

Chapter 4

Learning the Basics

This chapter covers the basics of using your computer.

Computing tips

❖ Save your work frequently.

Your work stays in the computer’s temporary memory until you save it to the disk. You will lose all the work since your last save if, for example, the network you are using goes down and you must restart your computer to reconnect, or your battery runs out of charge while you are working.

HINT: Some programs have an automatic-save feature which you can turn on. This feature saves your file to the hard disk at preset intervals. See your software documentation for details.

❖ Back up your files to disks (or other removable media) on

a regular basis. Label the backup copies clearly and store them in a safe place.

Page 89

Learning the Basics

Using the keyboard

It’s easy to put off backing up because it takes time. However, if your hard disk suddenly fails, you will lose all the data on it unless you have a separate backup copy.

❖ Use Error-checking and Disk Defragmenter regularly to

conserve disk space and improve performance.

❖ Scan all new files for viruses.

This precaution is especially important for files you receive via diskette, email, or download from the Internet.

❖ Take frequent breaks to avoid repetitive-motion injuries

and eyestrain.

❖ Do not turn off the computer if a drive indicator light

indicates a drive is active.

Turning off the computer while it is reading from or writing to a disk may damage the disk, the drive, or both.

❖ Before turning off the computer, use the Turn Off

Computer command or Standby command. See

“Powering down the computer” on page 113 to learn

more about Standby.

NOTE

The Windows®XP operating system records information, such as your desktop setup, during its shutdown procedure. If you do not let the Windows normally, details such as new icon positions may be lost.

Using the keyboard

Your computer’s keyboard contains character keys, control keys, function keys, and special Windows the functionality of a full-size keyboard.

XP operating system shut down

keys, providing all

Page 90

Learning the Basics

Using the keyboard

Keyboard

Character keys

Typing with the character keys is very much like typing on a typewriter, except that:

❖ The space bar creates a space character instead of just

passing over an area of the page.

❖ The lowercase letter l (el) and the number 1 are not

interchangeable.

❖ The uppercase letter O and the number 0 are not

interchangeable.

❖ The Caps Lock key changes only the alphabet keys to upper

case—the number and symbol keys are not affected. The caps lock light next to the caps lock key glows when you press the

Caps Lock key.

Making your keyboard emulate a full-size keyboard

Although your computer’s keyboard layout is compatible with a standard full-size keyboard, it has fewer keys.

A standard full-size keyboard has two editing keys, cursor positioning keys, and a numeric keypad. Pressing the of the specially marked keys allows you to emulate a full-size keyboard.

Your computer’s keyboard has only one Most of the time this does not matter. However, some

Fn key simultaneously in combination with one

Enter, Ctrl, and Alt keys,

Enter and one Ctrl key.

Page 91

programs assign separate functions to the right and left Ctrl

Alt keys, or to the regular and numeric pad Enter keys on

and the full-sized keyboard. Using the these separate keys, as follows:

❖ Press Fn and Ctrl simultaneously to simulate the Ctrl key on

the right side of the enhanced keyboard.

❖ Press Fn and Enter simultaneously to simulate the Enter key

on the numeric pad of the enhanced keyboard.

Ctrl, Fn, and Alt keys

Learning the Basics

Using the keyboard

Fn key you can simulate

Ctrl

Ctrl, Fn, and Alt keys

Ctrl, Fn, and Alt keys do different things depending on the

The program you are using. For more information, see your program documentation.

Function keys

The function keys (not to be confused with the Fn key) are the 12 keys at the top of the keyboard.

The function keys

F1 through F12 are called function keys because they execute

programmed functions when pressed. Used in combination with the specific functions on the computer. For more information, see

“Fn-esse®” on page 160, or “Hot Keys” on page 240.

Fn key, function keys marked with icons execute

Alt

Page 92

Learning the Basics

Using the keyboard

Windows special keys

The Windows special keys

Your computer’s keyboard has two keys that have special functions in Windows:

❖ Start key—Opens the Start menu

❖ Application key—Has the same function as the

secondary mouse (or AccuPoint II) button

Overlay keys

The keys with gray numbers and symbols on the front of them form the numeric and cursor overlay. This overlay lets you enter numeric data or control the cursor as you would using the 10-key keypad on a desktop computer’s keyboard.

Start key

Application key

Numeric and cursor control overlay

Using the overlay to type numeric data

The keys with the numbers on their right front are the numeric overlay keys.

Page 93

Learning the Basics

Using the keyboard

To turn the numeric overlay on, press Fn and F11 simultaneously. The numeric mode light on the keyboard indicator panel glows when the numeric overlay is on.

You can still use the overlay keys to type alphabetic characters while the numeric overlay is on. To do so:

❖ For lowercase letters, hold down Fn while you type the

letters.

❖ For uppercase letters, hold down both Fn and Shift while

you type the letters.

To use the cursor control keys when the numeric overlay is on:

❖ Press and hold down Shift while you use the cursor control

overlay keys.

❖ To return to the numeric overlay, release Shift.

To disable the numeric overlay, hold down the

F11 again. The numeric mode light on the keyboard

press indicator panel goes out.

Fn key and

Using the overlay for cursor control

The keys with the gray arrows and symbols on their left front are the cursor control overlay keys.

To turn the cursor control overlay on, press simultaneously. The cursor control mode light on the keyboard indicator panel glows when the cursor control overlay is on.

To type alphabetic characters while the overlay is on:

❖ For lowercase letters, hold down Fn while you type the

letters.

❖ For uppercase letters, hold down both Fn and Shift while

you type the letters.

To use the numeric overlay keys while the cursor control overlay is on:

Fn and F10

Page 94

Learning the Basics

Using the AccuPoint II pointing device

❖ Hold down Shift while you use the numeric overlay keys.

❖ To return to the cursor control overlay, release Shift.

To disable the cursor control overlay, hold down the and press keyboard indicator panel goes out.

F10 again. The cursor control mode light on the

Using the AccuPoint II pointing device

AccuPoint II pointing device

AccuPoint II buttons

TouchPad buttons

AccuPoint II keys

Accupoint II pointing device—Enables you to move the cursor and to select items on the screen. (If you prefer to use a mouse or trackball, you can connect one to the computer’s serial port or PS/2 port.)

To move the cursor, gently push the pointing device in the direction you want the cursor to move. Pushing harder on the pointing device moves the cursor faster.

Fn key

AccuPoint II buttons—Each button can be programmed to perform a function you select. To program these buttons:

1 Right-click the Toshiba Dual Pointing Device icon in the

task tray.

2 Click Detailed Setting.

3 Select the AccuPoint tab.

4 Under Buttons, choose the button to be programmed,

and select its new function from the pull-down menu.

Page 95

Learning the Basics

Using the TouchPad™

5 Click OK. The button is now programmed with the

function you chose.

Left TouchPad button—Performs the same function as the left button on a mouse. When a step instructs you to click or choose an item, move the cursor to the item, then press and release the left TouchPad button. To double-click, press this button twice in rapid succession.

Right TouchPad button—Performs the same function as the right button on a mouse.

Using the TouchPad

The TouchPad, the small, smooth square cutout located in front of the keyboard, is sensitive to touch and enables you to move the cursor with the stroke of a finger. Simply move your finger on the TouchPad in the direction you’d like to move the cursor:

❖ To move the cursor to the top of the page, push your

finger forward on the TouchPad.

❖ To move the cursor to the bottom of the page, drag your

finger toward yourself.

❖ To move the cursor to the right side of the page, slide

your finger across the TouchPad from left to right.

❖ To move it to the left side, slide your finger from right to

left.

NOTE

Because the TouchPad is much smaller than the display screen, moving your cursor across the screen often means having to move your finger several times across the TouchPad in the preferred direction.

™

Once you’ve positioned your cursor, you can either click it into place by double-tapping the TouchPad or clicking the control buttons.

Page 96

Learning the Basics

Using the TouchPad™

Control buttons

When a step instructs you to click or choose an item, move the cursor to the item, then press and release the primary (left-hand) button. To double-click, press the primary button twice in rapid succession. The primary button usually corresponds to the left mouse button.

The function of the secondary (right-hand) button depends on the program you are using. It usually corresponds to the right mouse button. Check your program’s documentation to find whether it uses the right mouse button.

Disabling or enabling the Dual Pointing Device

The Dual Pointing Device is enabled by default. To change the enable/disable Dual Point setting:

1 Click Start, Control Panel.

The Control Panel window appears.

2 Click Printers and Other Hardware.

3 Click Mouse Properties.

The Mouse Properties window appears.

4 Click the Dual Pointing Device tab.

The Dual Pointing Device tab view window appears.

5 Select Disable or Enable, whichever is appropriate.

6 Click Apply.

7 Click OK.

The Mouse Properties window closes.

8 Close the Printers and Other Hardware window.

9 Close the Control Panel window.

Page 97

Using TOSHIBA Console

The TOSHIBA Console icon, located on the Windows desktop, activates the Toshiba Console. This gives you quick access to some common functions.

To access the TOSHIBA Console:

1 Click Start, then click All Programs.

2 Point to Toshiba Console, then click the resulting

TOSHIBA Console selection.

The TOSHIBA Console window appears.

Learning the Basics

Sample TOSHIBA Console

The TOSHIBA Console offers three categories of features:

❖ Customize Your Computer

❖ Network

❖ Security

Page 98

Learning the Basics

Starting a program

The easiest way to start a program is to double-click the name of a file that is associated with the program you want to use. To find the file, use My Computer or Windows

If you prefer to open the program first, you have four options. You can:

❖ Use the Start menu

❖ Use Windows

program file

❖ Use the Run dialog box

The next three sections explain how to start a program from the Start menu, Explorer and the Run dialog box.

Starting a program from the Start menu

When you install a program, the operating system usually puts an icon in the All Programs menu. To start a program that has an icon in the All Programs menu, follow these steps, which use the Windows

Explorer or My Computer to locate the

Wordpad program as an example:

Explorer.

1 Click Start, then point to All Programs.

The Windows Programs menu, which lists programs and program groups. If your program is listed, go to Step 3, otherwise, continue with Step 2.

2 Point to the program group, in this example, Accessories.

The Accessories menu is displayed.

3 Click the program, in this example, Wordpad.

Wordpad opens.

To close the program, click the Close button in the upper-right corner of the program’s window.

XP operating system displays the All

Page 99

Learning the Basics

Starting a program

Starting a program from Windows® Explorer

If a program is not listed in the Programs menu, you can start it from Windows view of your computer’s contents as a hierarchy or “tree.” You can easily see the content of each drive and folder on your computer. To use this method, you should know the file name and location of the program’s executable file (this file ends with .exe).

This example opens Wordpad using its file name, wordpad.exe.

1 Click Start, then point to All Programs.

2 Click Accessories.

3 Click Windows Explorer.

4 Double-click My Computer.

5 Click on the C: drive in the left part of the window.

6 In the left part of the window, under the C: icon, double-

click the folder containing the program, in this case Program Files.

The files are hidden. Click on “Show the contents of this folder” on the right side of the window to see the files.

Windows folder on the right side of the window. The left side of the window shows all the folders contained within the Program Files folder.

Explorer. Windows® Explorer gives you a

Explorer shows the contents of the Program Files

7 In the left part of the window, click Windows NT.

8 Click Accessories.

Windows folder on the right side of the window.

9 In the right part of the window, double-click Wordpad.

The operating system opens Wordpad.

Explorer shows the contents of the Accessories

Page 100

Learning the Basics

100

Starting a program

To close the program, click the Close button in the upper-right corner of the program’s window.

Starting a program from the Run dialog box

This example uses the Run command to start Wordpad:

1 Click Start, then click Run.

The Run dialog box appears.

Sample Run dialog box

2 In the Run dialog box:

❖ For a program in the Windows

program name. Otherwise type the full file path, if you know the program’s location. Then click OK.

folder, type just the

❖ If you do not know the location, click Browse....

In the Browse dialog box, enter the file name (for example wordpad.exe) and select the drive to search. When the operating system has found the file, click Open.

HINT: To run the same program again, click the arrow to the right of the text box and select the command line from the drop-down list.

Toshiba S1, Tecra S1-117, Tecra S1 Series User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Contents

Introduction

Making sure you have everything

Finding where everything is located

Front with the display panel closed

Back

Left side

Right side

Front with the display panel open

Underside

Indicator panel lights

System indicator panel lights

Keyboard indicator panel lights

Selecting a place to work

Creating a computer-friendly environment

Keeping yourself comfortable

Other precautions

Setting up your computer

Connecting the AC adapter

Turning on the computer

Charging the battery

Opening the display panel

Turning on the power

Setting up your software

Registering your computer with Toshiba

Setting up other devices

Turning off the computer

Closing the display panel

Using external display devices

Connecting the display device

Directing the display output when you turn on the computer

Adjusting the quality of the external display

Video limitations

Using an external keyboard

Using a mouse

Making your external keyboard emulate the Fn key

Setting up a PS/2 mouse with the AccuPoint II

Connecting a local printer

Connecting an external diskette drive

Connecting external speakers or headphones

Connecting an external microphone

Using an expansion device

Adding memory

Installing a memory module

Removing a memory module

Using Slim SelectBay® modules

Inserting and removing hard drives

Inserting and removing PC Cards

Inserting a PC Card

Removing a PC Card

Inserting an SD® card

Setting up a PC Card for your computer

Connecting your modem to a telephone line

Connecting to a phone line

Computing tips

Using the keyboard

Character keys

Making your keyboard emulate a full-size keyboard

Ctrl, Fn, and Alt keys

Function keys

Windows special keys

Overlay keys

Using the AccuPoint II pointing device

Using the TouchPad™

Control buttons

Disabling or enabling the Dual Pointing Device

Using TOSHIBA Console

Starting a program

Starting a program from the Start menu

Starting a program from Windows® Explorer

Starting a program from the Run dialog box