Toshiba TECRA R10 User Manual

User’s Manual

TECRA R10

Table of Contents

Copyright. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi

Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi

Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi

FCC information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

EU Conformity Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii

VCCI Class B Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii

Following information is only valid for EU-member States:. . . . . . . . ix

Disposing of the computer and the computer's batteries . . . . . . . . . . x

Optical disc drive safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . xi

International precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii

Preface

Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiv

General Precautions

Provide adequate ventilation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xvii

Creating a computer-friendly environment . . . . . . . . . . . . . . . . . . . xviii

Stress injury . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xviii

Heat injury . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xviii

Pressure or impact damage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xix

Mobile phones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xix

Instruction Manual for Safety and Comfort . . . . . . . . . . . . . . . . . . . . xix

Chapter 1 Getting Started

Equipment checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

System Recovery Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12

System Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13

Chapter 2 The Grand Tour

Front with the display closed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Left side. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Right side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Back . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

User’s Manual ii

Underside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

Front with the display open. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8

Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11

Optical disc drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13

AC adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15

Chapter 3 Hardware, Utilities and Options

Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Special features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

TOSHIBA Value Added Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9

Utilities and Applications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11

Optional devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16

Optional accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-32

Chapter 4 Operating Basics

Using the Touch Pad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Using the Fingerprint Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

Web Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9

Using the TOSHIBA Face Recognition . . . . . . . . . . . . . . . . . . . . . . . 4-10

Using optical disc drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13

Writing CD/DVDs on DVD Super Multi drives . . . . . . . . . . . . . . . . . 4-17

TOSHIBA DVD PLAYER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23

Media care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-24

Sound System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25

Wireless communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-28

LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-31

Computer Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-33

Using the Hard Disk Drive (HDD) Protection . . . . . . . . . . . . . . . . . . 4-34

Using the TOSHIBA USB Sleep and Charge Utility . . . . . . . . . . . . . 4-36

Heat dispersal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-38

Chapter 5 The Keyboard

Typewriter keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Function keys: F1 … F12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

Soft keys: FN key combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

Hot keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3

Windows special keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5

Keypad overlay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

Generating ASCII characters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7

Chapter 6 Power and Power-Up Modes

Power conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

Monitoring of power condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4

Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5

TOSHIBA Password Utility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-14

Power-up modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-17

Panel power on/off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-18

TECRA R10

User’s Manual iii

System automatic Sleep/Hibernation . . . . . . . . . . . . . . . . . . . . . . . . 6-18

Chapter 7 HW Setup

Accessing HW Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

HW Setup window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

Chapter 8 Troubleshooting

Problem solving process. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

Hardware and system checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3

Using Windows XP Mode on your Windows 7 computer (available on

certain models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-22

TOSHIBA support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-22

Appendix A Specifications

Physical Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Environmental Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Appendix B Display Controller and Video mode

Display controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1

Video mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1

Appendix C Wireless LAN

Card Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1

Radio Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2

Supported Frequency Sub-bands. . . . . . . . . . . . . . . . . . . . . . . . . . . . C-3

Appendix D Bluetooth wireless technology Interoperability

Bluetooth wireless technology and your Health . . . . . . . . . . . . . . . . D-2

Regulatory statements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-2

Using Bluetooth Adaptor from TOSHIBA equipment in Japan . . . . D-4

Appendix E AC Power Cord and Connectors

Certification agencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-1

Appendix F TOSHIBA Anti-theft Protection Timer

Appendix G TOSHIBA PC Health Monitor

Starting the TOSHIBA PC Health Monitor. . . . . . . . . . . . . . . . . . . . . . G-2

If a TOSHIBA PC Health Monitor message is displayed. . . . . . . . . . G-2

Cleaning the cooling module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G-3

Appendix H Legal Footnotes

Non-applicable Icons*1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H-1

CPU*2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H-1

Memory (Main System)*3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H-2

Battery Life*4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H-3

Hard Disk Drive (HDD) Capacity*5 . . . . . . . . . . . . . . . . . . . . . . . . . . . H-3

LCD*6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H-3

Graphics Processor Unit ("GPU")*7 . . . . . . . . . . . . . . . . . . . . . . . . . . H-3

Wireless LAN*8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H-4

TECRA R10

User’s Manual iv

TECRA R10

USB Sleep and Charge*9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H-4

Copy Protection*10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H-4

Glossary

Index

User’s Manual v

Copyright

Disclaimer

TECRA R10

© 2009 by TOSHIBA Corporation. All rights reserved. Under the copyright
laws, this manual cannot be reproduced in any form without the prior
written permission of TOSHIBA. No patent liability is assumed, with respect
to the use of the information contained herein.

TOSHIBA TECRA R10 Portable Personal Computer User’s Manual

First edition September 2009
Copyright authority for music, movies, computer programs, databases and

other intellectual property covered by copyright laws belongs to the author
or to the copyright owner. Copyrighted material can be reproduced only for
personal use or use within the home. Any other use beyond that stipulated
above (including conversion to digital format, alteration, transfer of copied
material and distribution on a network) without the permission of the
copyright owner is a violation of copyright or author's rights and is subject to
civil damages or criminal action. Please comply with copyright laws in
making any reproduction from this manual.

This manual has been validated and reviewed for accuracy. The
instructions and descriptions it contains are accurate for the TOSHIBA
TECRA R10 Portable Personal Computer at the time of this manual’s
production. However, succeeding computers and manuals are subject to
change without notice. TOSHIBA assumes no liability for damages incurred
directly or indirectly from errors, omissions or discrepancies between the
computer and the manual.

Trademarks

IBM is a registered trademark and IBM PC is a trademark of International
Business Machines Corporation.

Intel, Intel SpeedStep, Intel Core and Centrino are trademarks or registered
trademarks of Intel Corporation.

Windows, Microsoft and Windows logo are registered trademarks of
Microsoft Corporation.

Bluetooth is a trademark owned by its proprietor and used by TOSHIBA
under license.

Photo CD is a trademark of Eastman Kodak Company.
ExpressCard is a trademark of PCMCIA.
ConfigFree is a trademark of Toshiba Corporation.
Wi-Fi is a registered trademark of the Wi-Fi Alliance.
Secure Digital and SD are trademarks of SD Card Association.
Other trademarks and registered trademarks not listed above may be used

in this manual.

User’s Manual vi

FCC information

FCC notice "Declaration of Conformity Information"

This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

■ Reorient or relocate the receiving antenna.

■ Increase the separation between the equipment and receiver.

■ Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

■ Consult the dealer or an experienced radio/TV technician for help.

Only peripherals complying with the FCC class B limits may be attached to
this equipment. Operation with non-compliant peripherals or peripherals
not recommended by TOSHIBA is likely to result in interference to radio
and TV reception. Shielded cables must be used between the external
devices and the computer’s external monitor port, Universal Serial Bus
(USB 2.0) ports, eSATA/USB combo port and microphone jack. Changes
or modifications made to this equipment, not expressly approved by
TOSHIBA or parties authorized by TOSHIBA could void the user’s
authority to operate the equipment.

TECRA R10

FCC conditions

This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including
interference that may cause undesired operation.

Contact

Address: TOSHIBA America Information Systems, Inc.

9740 Irvine Boulevard
Irvine, California 92618-1697

Telephone: [phone]

User’s Manual vii

EU Conformity Statement

This product and - if applicable - the supplied accessories too are marked
with "CE" and comply therefore with the applicable harmonized European
standards listed under the Low Voltage Directive 2006/95/EC, the EMC
Directive 2004/108/EC and/or R&TTE Directive 1999/5/EC.

Responsible for CE­marking:

Manufacturer: Toshiba Corporation, 1-1 Shibaura 1-chome,

The complete official EU CE Declaration can be obtained on following
internet page:

http://epps.toshiba-teg.com/

VCCI Class B Information

TECRA R10

TOSHIBA EUROPE GMBH, Hammfelddamm 8,
41460 Neuss, Germany.

Minato-ku, Tokyo, 105-8001, Japan

User’s Manual viii

TECRA R10

Following information is only valid for EU-member States:

Disposal of products

The crossed out wheeled dust bin symbol indicates that products must be
collected and disposed of separately from household waste. Integrated
batteries and accumulators can be disposed of with the product. They will
be separated at the recycling centres.

The black bar indicates that the product was placed on the market after
August 13, 2005.

By participating in separate collection of products and batteries, you will
help to assure the proper disposal of products and batteries and thus help
to prevent potential negative consequences for the environment and
human health.

For more detailed information about the collection and recycling
programmes available in your country, please visit our website
(http://eu.computers.toshiba-europe.com) or contact your local city office or
the shop where you purchased the product.

Disposal of batteries and/or accumulators

The crossed out wheeled dust bin symbol indicates that batteries and/or
accumulators must be collected and disposed of separately from
household waste.

If the battery or accumulator contains more than the specified values of
lead (Pb), mercury (Hg), and/or cadmium (Cd) defined in the Battery
Directive (2006/66/EC), then the chemical symbols for lead (Pb), mercury
(Hg) and/or cadmium (Cd) will appear below the crossed out wheeled dust
bin symbol.

By participating in separate collection of batteries, you will help to assure
the proper disposal of products and batteries and thus help to prevent
potential negative consequences for the environment and human health.

For more detailed information about the collection and recycling
programmes available in your country, please visit our website
(http://eu.computers.toshiba-europe.com) or contact your local city office or
the shop where you purchased the product.

These symbols may not stick depending on the country and region where
you purchased.

User’s Manual ix

TECRA R10

Disposing of the computer and the computer's batteries

■ Discard this computer in accordance with applicable laws and

regulations. For further information, contact your local government.

■ This computer contains rechargeable batteries. After repeated use, the

batteries will finally lose their ability to hold a charge and you will need
to replace them. Under certain applicable laws and regulation, it may be
illegal to dispose of old batteries by placing them in the trash.

■ Please be kind to our shared environment. Check with your local

government authority for details regarding where to recycle old batteries
or how to dispose of them properly.

User’s Manual x

Optical disc drive safety instructions

Be sure to check the international precautions at the end of this section.

Panasonic Communications

DVD Super Multi with Double Layer Recording UJ862

■ The DVD Super Multi drive model employs a laser system. To ensure

proper use of this product, please read this instruction manual carefully
and retain for future reference. Should the unit ever require
maintenance, contact an authorized service location.

■ Use of controls, adjustments or the performance of procedures other

than those specified may result in hazardous radiation exposure.

■ To prevent direct exposure to the laser beam, do not try to open the

enclosure.

TECRA R10

User’s Manual xi

International precautions

TECRA R10

CAUTION: This appliance contains a
laser system and is classified as a
“CLASS 1 LASER PRODUCT.” To use
this model properly, read the instruction
manual carefully and keep this manual
for your future reference. In case of any
trouble with this model, please contact
your nearest “AUTHORIZED service
station.” To prevent direct exposure to the
laser beam, do not try to open the
enclosure.

VORSICHT: Dieses Gerät enthält ein
Laser-System und ist als
“LASERSCHUTZKLASSE 1 PRODUKT”
klassifiziert. Für den richtigen Gebrauch
dieses Modells lesen Sie bitte die
Bedienungsanleitung sorgfältig durch
und bewahren diese bitte als Referenz
auf. Falls Probleme mit diesem Modell
auftreten, benachrichtigen Sie bitte die
nächste “autorisierte Service-Vertretung”.
Um einen direkten Kontakt mit dem
Laserstrahl zu vermeiden darf das Gerät
nicht geöffnet werden.

User’s Manual xii

ADVARSEL: Denne mærking er anbragt
udvendigt på apparatet og indikerer, at
apparatet arbejder med laserstråler af
klasse 1, hviket betyder, at der anvendes
laserstrlier af svageste klasse, og at man
ikke på apparatets yderside kan bilve
udsat for utilladellg kraftig stråling.

APPARATET BOR KUN ÅBNES AF
FAGFOLK MED SÆRLIGT KENDSKAB
TIL APPARATER MED
LASERSTRÅLER!

Indvendigt i apparatet er anbragt den her
gengivne advarselsmækning, som
advarer imod at foretage sådanne
indgreb i apparatet, at man kan komme til
at udsatte sig for laserstråling.

TECRA R10

OBS! Apparaten innehåller
laserkomponent som avger laserstråining
överstigande gränsen för laserklass 1.

VAROITUS. Suojakoteloa si saa avata.
Laite sisältää laserdiodin, joka lähetää
näkymätöntä silmilie vaarallista
lasersäteilyä.

CAUTION: USE OF CONTROLS OR
ADJUSTMENTS OR PERFORMANCE
OF PROCEDURES OTHER THAN
THOSE SPECIFIED IN THE OWNER’S
MANUAL MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.

VORSICHT: DIE VERWENDUNG VON
ANDEREN STEURUNGEN ODER
EINSTELLUNGEN ODER DAS
DURCHFÜHREN VON ANDEREN
VORGÄNGEN ALS IN DER
BEDIENUNGSANLEITUNG
BESCHRIEBEN KÖNNEN
GEFÄHRLICHE
STRAHLENEXPOSITIONEN ZUR
FOLGE HABEN.

User’s Manual xiii

Preface

Congratulations on your purchase of the TECRA R10 computer. This
powerful notebook computer provides excellent expansion capability,
includes multimedia functionality, and is designed to provide years of
reliable, high-performance computing.

This manual tells how to set up and begin using your TECRA R10
computer. It also provides detailed information on configuring your
computer, basic operations and care, using optional devices and
troubleshooting.

If you are a new user of computers or if you’re new to portable computing,
first read over the Chapter 1, Getting Started and Chapter 3, Hardware,

Utilities and Options chapters to familiarize yourself with the computer’s

features, components and accessory devices. Then read Chapter 1,

Getting Started for step-by-step instructions on setting up your computer.

If you are an experienced computer user, please continue reading the
preface to learn how this manual is organized, then become acquainted
with this manual by browsing through its pages. Be sure to read the Special

features section in Chapter 3, Hardware, Utilities and Options to learn

about features that are uncommon or unique to this computer, as well as
the section on Chapter 7, HW Setup, to understand how to setup and
configure these features.

Read Chapter 3, Hardware, Utilities and Options if connecting optional
products or external devices.

Conventions

This manual uses the following formats to describe, identify, and highlight
terms and operating procedures.

Abbreviations

On first appearance, and whenever necessary for clarity, abbreviations are
enclosed in parentheses following their definition. For example: Read Only
Memory (ROM). Acronyms are also defined in the Glossary.

User’s Manual xiv

Icons

Icons identify ports, dials, and other parts of your computer. The indicator
panel also uses icons to identify the components it is providing information
on.

Keys

The keyboard keys are used in the text to describe many computer
operations. A distinctive typeface identifies the key top symbols as they
appear on the keyboard. For example, ENTER identifies the ENTER key.

Key operation

Some operations require you to simultaneously use two or more keys. We
identify such operations by the key top symbols separated by a plus sign
(+). For example, CTRL + C means you must hold down CTRL and at the
same time press C. If three keys are used, hold down the first two and at
the same time press the third.

TECRA R10

ABC

When procedures require an action such as
clicking an icon or entering text, the icon's name
or the text you are to type in is represented in the
typeface you see to the left.

Display

S ABC

Names of windows or icons or text generated by
the computer that appear on its display screen
are presented in the type face you see to the left.

Messages

Messages are used in this manual to bring important information to your
attention. Each type of message is identified as shown below.

Pay attention! A caution informs you that improper use of equipment or
failure to follow instructions may cause data loss or damage your
equipment.

Please read. A note is a hint or advice that helps you make best use of
your equipment.

Indicates a potentially hazardous situation, which could result in death or
serious injury, if you do not follow instructions.

User’s Manual xv

Terminology

This term is defined in this document as follows:

Start The word "Start" refers to the " " button in

Windows 7.

HDD or Hard disk
drive

Some models are equipped with a "Solid State
Drive (SSD)" instead of a hard disk drive.

In this manual, the word "HDD" or "Hard disk
drive" also refers to the SSD unless otherwise
stated.

TECRA R10

User’s Manual xvi

General Precautions

TOSHIBA computers are designed to optimize safety, minimize strain and
withstand the rigors of portability. However, certain precautions should be
observed to further reduce the risk of personal injury or damage to the
computer.

Be certain to read the general precautions below and to note the cautions
included in the text of the manual.

Provide adequate ventilation

■ Always make sure your computer and AC adaptor have adequate

ventilation and are protected from overheating when the power is
turned on or when an AC adaptor is connected to a power outlet (even if
your computer is in Sleep Mode). In this condition, observe the
following:

■ Never cover your computer or AC adaptor with any object.

■ Never place your computer or AC adaptor near a heat source, such

as anelectric blanket or heater.

■ Never cover or block the air vents including those located at the

base of the computer.

■ Always operate your computer on a hard flat surface. Using your

computer on a carpet or other soft material can block the vents.

■ Always provide sufficient space around the computer.

■ Overheating your computer or AC adaptor could cause system failure,

computer or AC adaptor damage or a fire, possibly resulting in serious
injury.

User’s Manual xvii

Creating a computer-friendly environment

Place the computer on a flat surface that is large enough for the computer
and any other items you are using, such as a printer.

Leave enough space around the computer and other equipment to provide
adequate ventilation. Otherwise, they may overheat.

To keep your computer in prime operating condition, protect your work area
from:

■ Dust, moisture, and direct sunlight.

■ Equipment that generates a strong electromagnetic field, such as

stereo speakers (other than speakers that are connected to the
computer) or speakerphones.

■ Rapid changes in temperature or humidity and sources of temperature

change such as air conditioner vents or heaters.

■ Extreme heat, cold, or humidity.

■ Liquids and corrosive chemicals.

Stress injury

Carefully read the Instruction Manual for Safety and Comfort. It contains
information on the prevention of stress injuries to your hands and wrists
that can be caused by extensive keyboard use. Instruction Manual for
Safety and Comfort also includes information on work space design,
posture and lighting that can help reduce physical stress.

TECRA R10

Heat injury

■ Avoid prolonged physical contact with the computer. If the computer is

used for long periods, its surface can become very warm. While the
temperature will not feel hot to the touch, if you maintain physical
contact with the computer for a long time, for example if you rest the
computer on your lap or if you keep your hands on the palm rest, your
skin might suffer a low-heat injury.

■ If the computer has been used for a long time, avoid direct contact with

the metal plate supporting the various interface ports as this can
become hot.

■ The surface of the AC adaptor can become hot when in use but this

condition does not indicate a malfunction. If you need to transport the
AC adaptor, you should disconnect it and let it cool before moving it.

■ Do not lay the AC adaptor on a material that is sensitive to heat as the

material could become damaged.

User’s Manual xviii

Pressure or impact damage

Do not apply heavy pressure to the computer or subject it to any form of
strong impact as this can damage the computer's components or otherwise
cause it to malfunction.

Mobile phones

Please be aware that the use of mobile phones can interfere with the audio
system. The operation of the computer will not be impaired in any way, but
it is recommended that a minimum distance of 30cm is maintained between
the computer and a mobile phone that is in use.

Instruction Manual for Safety and Comfort

All important information on the safe and proper use of this computer is
described in the enclosed Instruction Manual for Safety and Comfort. Be
sure to read it before using the computer.

TECRA R10

User’s Manual xix

Getting Started

This chapter provides an equipment checklist, and basic information to start
using your computer.

Some of the features described in this manual may not function properly if
you use an operating system that was not pre-installed by TOSHIBA.

Equipment checklist

Carefully unpack your computer, taking care to save the box and packaging
materials for future use.

Hardware

Check to make sure you have all the following items:

■ TECRA R10 Portable Personal Computer

■ AC adaptor and power cord (2-pin plug or 3-pin plug)

■ Battery pack

Chapter 1

Documentation

■ TECRA R10 User Information Guide

■ Instruction Manual for Safety and Comfort

■ End User License Agreement

If any of the items are missing or damaged, contact your dealer
immediately.

User’s Manual 1-1

Software

The following Windows® operating system and utility software are pre­installed.

■ Windows 7

■ TOSHIBA Value Added Package

■ Recovery Media Creator

■ TOSHIBA DVD Player

■ TOSHIBA SD Memory Utilities

■ TOSHIBA SD Memory Boot Utility

■ TOSHIBA Assist

■ TOSHIBA ConfigFree™

■ TOSHIBA HDD Protection (Is preinstalled in some models)

■ TOSHIBA Disc Creator

■ TOSHIBA eco Utility

■ TOSHIBA Face Recognition (Is preinstalled in some models)

■ TOSHIBA PC Health Monitor

■ TOSHIBA USB Sleep and Charge Utility

■ TOSHIBA Fingerprint Utility (Is preinstalled in some models)

■ Online Manual

■ TECRA R10 User's Manual (This manual)

Getting Started

User’s Manual 1-2

Getting Started

■ All users should be sure to read the section Starting up for the first time.

■ Be sure to read the enclosed Instruction Manual for Safety and Comfort

for information on the safe and proper use of this computer. It is
intended to help you be more comfortable and productive while using a
notebook computer. By following the recommendations in it you may
reduce your chance of developing a painful or disabling injury to your
hand, arms, shoulders or neck.

This section provides basic information to start using your computer. It
covers the following topics:

■ Connecting the AC adaptor

■ Opening the display

■ Turning on the power

■ Starting up for the first time

■ Turning off the power

■ Restarting the computer

■ System Recovery Options

■ Creating Recovery Media

■ Restoring the pre-installed software from the Recovery hard disk drive

■ Restoring the pre-installed software from your created Recovery Media

Getting Started

■ Use a virus-check program and make sure it is updated regularly.

■ Never format storage media without checking its content - formatting

destroys all stored data.

■ It is a good idea to periodically back up the internal hard disk drive or

other main storage device to external media. General storage media is
not durable or stable over long periods of time and under certain
conditions may result in data loss.

■ Before you install a device or application, save any data in memory to

the hard disk drive or other storage media. Failure to do so may result
in the loss of data.

User’s Manual 1-3

Connecting the AC adaptor

Attach the AC adaptor when you need to charge the battery or you want to
operate from AC power. It is also the fastest way to get started, because
the battery pack will need to be charged before you can operate from
battery power.

The AC adaptor can be connected to any power source supplying from 100
to 240 volts and 50 or 60 hertz. For details on using the AC adaptor to
charge the battery pack, refer to Chapter 6, Power and Power-Up Modes.

■ Always use the TOSHIBA AC adaptor that was included with your

computer, or use AC adaptors specified by TOSHIBA to avoid any risk
of fire or other damage to the computer. Use of an incompatible AC
adaptor could cause fire or damage to the computer possibly resulting
in serious injury. TOSHIBA assumes no liability for any damage caused
by use of an incompatible adaptor.

■ Never plug the AC adaptor into a power source that does not

correspond to both the voltage and the frequency specified on the
regulatory label of the unit. Failure to do so could result in a fire or
electric shock, possibly resulting in serious injury.

■ Always use or purchase power cables that comply with the legal

voltage and frequency specifications and requirements in the country of
use. Failure to do so could result in a fire or electric shock, possibly
resulting in serious injury.

■ The supplied power cord conforms to safety rules and regulations in

the region the product is bought and should not be used outside this
region. For use in other regions, please buy power cords that conform
to safety rules and regulations in the particular region.

■ Do not use a 3-pin to 2-pin conversion plug.

■ When you connect the AC adaptor to the computer, always follow the

steps in the exact order as described in the User’s Manual. Connecting
the power cable to a live electrical outlet should be the last step
otherwise the adaptor DC output plug could hold an electrical charge
and cause an electrical shock or minor bodily injury when touched. As
a general safety precaution, avoid touching any metal parts.

■ Never place your computer or AC adaptor on a wooden surface,

furniture, or any other surface that could be marred by exposure to heat
since the computer base and AC adaptor's surface increase in
temperature during normal use.

■ Always place your computer or AC adaptor on a flat and hard surface

that is resistant to heat damage.

Refer to the enclosed Instruction Manual for Safety and Comfort for
detailed precautions and handling instructions.

Getting Started

User’s Manual 1-4

Getting Started

1. Connect the power cord to the AC adaptor.

Figure 1-1 Connecting the power cord to the AC adaptor (2-pin plug)

Figure 1-2 Connecting the power cord to the AC adaptor (3-pin plug)

Either a 2-pin or 3-pin adaptor/cord will be included with the computer
depending on the model.

2. Connect the AC adaptor’s DC output plug to the DC IN 15V jack on the
right side of the computer.

DC IN 15V jack

DC output plug

Figure 1-3 Connecting the DC output plug to the computer

3. Plug the power cord into a live wall outlet - the Battery and DC IN
indicators on the front of the computer should glow.

User’s Manual 1-5

Opening the display

The display panel can be opened to a wide range of angles for optimal
viewing.

While holding down the palm rest with one hand so that the main body of
the computer is not raised, slowly lift the display panel - this will allow the
angle of the display panel to be adjusted to provide optimum clarity.

Display panel

Figure 1-4 Opening the display panel

Use reasonable care when opening and closing the display panel. Opening
it vigorously or slamming it shut could damage the computer.

Getting Started

■ Be careful not to open the display panel too far as this could put stress

on the display panel’s hinges and cause damage.

■ Do not press or push on the display panel.

■ Do not lift the computer by the display panel.

■ Do not close the display panel with pens or any other objects left in

between the display panel and the keyboard.

■ When opening or closing the display panel, place one hand on the

palm rest to hold the computer in place and use the other hand to
slowly open or close the display panel (Do not use excessive force
when opening or closing the display panel).

User’s Manual 1-6

Turning on the power

This section describes how to turn on the power - the Power indicator will
then indicate the status. Please refer to the Monitoring of power condition
section in Chapter 6, Power and Power-Up Modes for more information.

■ After you turn on the power for the first time, do not turn it off until you

have set up the operating system. Please refer to the section Starting

up for the first time for more information.

■ Volume cannot be adjusted during Windows Setup.

1. Open the display panel.

2. Press and hold the computer's power button for two or three seconds.

Power button

Getting Started

Figure 1-5 Turning on the power

Starting up for the first time

The Windows 7 Startup Screen will be the first screen displayed when you
turn on the power. Follow the on-screen instructions on each screen in
order to properly install the operating system.

When it is displayed, be sure to read the Software License Terms
carefully.

Turning off the power

The power can be turned off in one of three modes, either Shut Down
Mode, Hibernation Mode or Sleep Mode.

Shut Down Mode

When you turn off the power in Shut Down Mode no data will be saved and
the computer will boot to the operating system's main screen the next time
it is turned on.

1. If you have entered data, either save it to the hard disk drive or to other
storage media.

2. Make sure all disk/disc activity has stopped before removing the
CD/DVD or floppy diskette.

User’s Manual 1-7

Getting Started

■ Make sure the Hard Disk Drive indicator is off. If you turn off the power

while a disk (disc) is being accessed, you may lose data or damage the
disk.

■ Never turn off the power while an application is running. Doing so could

cause loss of data.

■ Never turn off the power, disconnect an external storage device or

remove storage media during data read/write. Doing so can cause data
loss.

3. Click Start.

4. Click the Shut down button ( ).

5. Turn off any peripheral devices connected to your computer.

Do not turn the computer or peripheral devices back on immediately - wait
a short period to avoid any potential damage.

Sleep Mode

If you have to interrupt your work, you are able to turn off the power without
exiting from your software by placing the computer into Sleep Mode. In this
mode data is maintained in the computer's main memory so that when you
turn on the power again, you can continue working right where you left off.

When you have to turn off your computer aboard an aircraft or in places
where electronic devices are regulated or controlled, always completely
shut down the computer. This includes turning off any wireless
communication switches or devices, and canceling settings that reactivate
the computer automatically, such as a timer recording function. Failure to
completely shut down the computer in this way could allow the operating
system to reactivate and run pre-programmed tasks or preserve unsaved
data, which could interfere with aviation or other systems, possibly causing
serious injury.

■ Before entering Sleep Mode, be sure to save your data.

■ Do not install or remove a memory module while the computer is in

Sleep Mode. The computer or the memory module could be damaged.

■ Do not remove the battery pack while the computer is in Sleep Mode

(unless the computer is connected to an AC power source). Data in
memory could be lost.

User’s Manual 1-8

Getting Started

■ When the AC adaptor is connected, the computer will go into Sleep

Mode according to the settings in the Power Options (to access it, Start

-> Control Panel -> System and Security -> Power Options).

■ To restore the operation of the computer from Sleep Mode, press and

hold the power button or any key on the keyboard for a short amount of
time. Please note that keyboard keys can only be used if the Wake-up
on Keyboard option is enabled within the HW Setup utility.

■ If the computer enters Sleep Mode while a network application is

active, the application might not be restored when the computer is next
turned on and the system returns from Sleep Mode.

■ To prevent the computer from automatically entering Sleep Mode,

disable Sleep Mode within the Power Options (to access it, Start ->
Control Panel -> System and Security -> Power Options).

■ To use the Hybrid Sleep function, configure it in the Power Options.

Benefits of Sleep Mode

The Sleep Mode feature provides the following benefits:

■ Restores the previous working environment more rapidly than does the

Hibernation Mode feature.

■ Saves power by shutting down the system when the computer receives

no input or hardware access for the time period set by the System
Sleep Mode feature.

■ Allows the use of the panel power off feature.

Executing Sleep Mode

You can also enable Sleep Mode by pressing FN + F3 - please refer to
Chapter 5, The Keyboard, for further details.

You can enter Sleep Mode in one of three ways:

■ Click Start, point to the arrow icon ( ) and select Sleep

from the menu.

■ Close the display panel. Please note that this feature must be enabled

within the Power Options (to access it, click Start -> Control Panel

-> System and Security -> Power Options).

■ Press the power button. Please note that this feature must be enabled

within the Power Options (to access it, click Start -> Control Panel

-> System and Security -> Power Options).

When you turn the power back on, you can continue where you left when
you shut down the computer.

■ When the computer is in Sleep Mode, the power indicator will blink

orange.

■ If you are operating the computer on battery power, you can lengthen

the overall operating time by turning it off into Hibernation Mode - Sleep
Mode will consume more power while the computer is off.

User’s Manual 1-9

Getting Started

Sleep Mode limitations

Sleep Mode will not function under the following conditions:

■ Power is turned back on immediately after shutting down.

■ Memory circuits are exposed to static electricity or electrical noise.

Hibernation Mode

The Hibernation Mode feature saves the contents of memory to the hard
disk drive when the computer is turned off so that, the next time it is turned
on, the previous state is restored. Please note that the Hibernation Mode
feature does not save the status of any peripheral devices connected to the
computer.

■ Save your data. While entering Hibernation Mode, the computer saves

the contents of memory to the hard disk drive. However, for safety
sake, it is best to save your data manually.

■ Data will be lost if you remove the battery or disconnect the AC adaptor

before the save is completed. Wait for the Hard Disk Drive indicator to
go out.

■ Do not install or remove a memory module while the computer is in

Hibernation Mode. Data will be lost.

Benefits of Hibernation Mode

The Hibernation Mode feature provides the following benefits:

■ Saves data to the hard disk drive when the computer automatically

shuts down because of a low battery condition.

■ You can return to your previous working environment immediately when

you turn on the computer.

■ Saves power by shutting down the system when the computer receives

no input or hardware access for the time period set by the System
Hibernate feature.

■ Allows the use of the panel power off feature.

Starting Hibernation Mode

You can also enable Hibernation Mode by pressing FN + F4 - please refer
to Chapter 5, The Keyboard, for further details.

To enter Hibernation Mode, follow the steps below.

1. Click Start.

2. Point to the arrow icon ( ) and then select Hibernate
from the menu.

User’s Manual 1-10

Automatic Hibernation Mode

The computer can be configured to enter Hibernation Mode automatically
when you press the power button or close the lid. In order to define these
settings, you can follow the steps as described below:

1. Click Start and click the Control Panel.

2. Click System and Security and click Power Options.

3. Click Choose what the power button does or Choose what closing
the lid does.

4. Enable the desired Hibernation Mode settings for When I press the
power button and When I close the lid.

5. Click the Save changes button.

Data save in Hibernation Mode

When you turn off the power in Hibernation Mode, the computer will take a
moment to save the current data in memory to the hard disk drive. During
this time, the Hard Disk Drive indicator will glow.

After you turn off the computer, and the content of memory has been saved
to the hard disk drive, turn off the power to any peripheral devices.

Do not turn the computer or devices back on immediately. Wait a moment
to let all capacitors fully discharge.

Restarting the computer

Certain conditions require that you reset the computer, for example if:

■ You change certain computer settings.

■ An error occurs and the computer does not respond to your keyboard

commands.

If you need to restart the computer, there are three ways this can be
achieved:

■ Click Start, point to the arrow icon ( ) and then select

Restart from the menu.

■ Press CTRL, ALT and DEL simultaneously (once) to display the menu

window, then select Restart from the Shut down options.

■ Press the power button and hold it down for five seconds. Once the

computer has turned itself off, wait between ten and fifteen seconds
before turning the power on again by pressing the power button.

Getting Started

User’s Manual 1-11

System Recovery Options

There is a hidden partition allocated on the hard disk drive for the System
Recovery Options.

This partition stores files which can be used to repair the system in the
event of a problem.

The System Recovery Options feature will be unusable if this partition is
deleted.

System Recovery Options

The System Recovery Options feature is installed on the hard disk when
shipped from the factory. The System Recovery Options menu includes
tools to repair startup problems, run diagnostics or restore the system.

See the Windows Help and Support content for more information about
Startup Repair.

The System Recovery Options can also be run manually to repair
problems.

The procedure is as follows. Follow the instructions shown on the on­screen menu.

1. Turn off the computer.

2. While holding the F8 key, turn on the computer.

3. The Advanced Boot Options menu will be displayed.
Use the arrow keys to select Repair Your Computer and press
ENTER.

4. Follow the on-screen instructions.

Getting Started

Check your Windows® manual for more information on backing up your
system (including the system image backup feature).

User’s Manual 1-12

System Recovery

This section describes the creation of Recovery Media and their use.

Creating Recovery Media

This section describes how to create Recovery Media.

■ Be sure to connect the AC adaptor when you create Recovery Media.

■ Be sure to close all other software programs except the Recovery

Media Creator.

■ Do not run software such as screen savers which can put a heavy load

on the CPU.

■ Operate the computer at full power.

■ Do not use power-saving features.

■ Do not write to the media when the virus check software is running.

Wait for it to finish, then disable virus detection programs including any
software that checks files automatically in the background.

■ Do not use utilities, including those intended to enhance hard disk drive

access speed. They may cause unstable operation and damage data.

■ Do not shut down/log off or Sleep/Hibernate while writing or rewriting

the media.

■ Set the computer on a level surface and avoid places subjected to

vibrations such as airplanes, trains, or cars.

■ Do not use on an unstable surface such as a stand.

Getting Started

A recovery image of the software on your computer is stored on the hard
disk drive, and can be copied to either DVD or USB Flash Memory by using
the following steps:

1. Select either blank DVD or USB Flash Memory.

2. The application will allow you to choose from a variety of different media
onto which the recovery image can be copied including DVD-R, DVD-R
DL, DVD-RW, DVD+R, DVD+R DL, DVD+RW and USB Flash Memory.

■ Please note that some of the above media may not be compatible with

the optical disc drive installed into your computer. You should therefore
verify the optical disc drive supports the blank media you have chosen
before proceeding.

■ USB Flash Memory will be formatted and all the data in the USB flash

drive will be lost when proceeding.

3. Turn on your computer and allow it to load the Windows 7 operating
system from the hard disk drive as normal.

4. Insert the media into the computer.

■ Insert the first blank disc into the optical disc drive tray, or

■ Insert the USB Flash Memory into one available USB port

5. Double click the Recovery Media Creator icon on the Windows 7
desktop, or select the application from Start Menu.

User’s Manual 1-13

Getting Started

6. After Recovery Media Creator starts, select the type of media and the
title you wish to copy. The screen will display the number of discs or the
capacity of USB Flash Memory required. Make sure you have a
sufficient number of discs or sufficient capacity of USB Flash Memory
before you proceed with the Recovery Media process.

7. Click the Create button to proceed.

Restoring the pre-installed software from the Recovery hard disk
drive

A portion of the total hard disk drive space is configured as a hidden
recovery partition. This partition stores files which can be used to restore
pre-installed software in the event of a problem.

If you subsequently set up your hard disk drive again, do not change,
delete or add partitions in a manner other than specified in the manual,
otherwise you may find that space for the required software is not available.

In addition, if you use a third-party partitioning program to reconfigure the
partitions on your hard disk drive, you may find that it becomes impossible
to setup your computer.

When the sound mute feature has been activated by pressing the FN +
ESC key, be sure to disable this to allow sounds to be heard before starting

the restore process. Please refer to Chapter 5, The Keyboard, for further
details.

You can not use System Recovery Options if restoring the pre-installed
software without System Recovery Options.

When you reinstall the Windows operating system, the hard disk will be
reformatted and all data will be lost.

1. Turn off your computer.

2. While holding down 0 (zero) key on the keyboard, turn on your
computer.

3. A menu will be displayed from which you should follow the on-screen
instructions.

User’s Manual 1-14

Getting Started

Restoring the pre-installed software from your created Recovery
Media

If the pre-installed files are damaged, you are able to either use the
Recovery Media you have created or the hard disk drive recovery process
to restore the computer to the state it was in when you originally received it.
To perform this restoration, follow the steps below:

When the sound mute feature has been activated by pressing the FN +
ESC key, be sure to disable this to allow sounds to be heard before starting

the restore process. Please refer to Chapter 5, The Keyboard, for further
details.

You can not use System Recovery Options if restoring the pre-installed
software without System Recovery Options.

When you reinstall the Windows operating system, the hard disk will be
reformatted and all data will be lost.

1. Load the Recovery Media into the computer and turn off the computer's
power.

2. While holding down F12 key on the keyboard, turn on your computer ­when the TOSHIBA logo screen appears, release the F12 key.

3. Use the left and right cursors key to select the appropriate icon (CD­ROM or USB icon) of your actual recovery media from the menu.
Please refer to the Boot Priority section in Chapter 7, HW Setup for
further information.

4. A menu will be displayed from which you should follow the on-screen
instructions.

When drivers/utilities are installed, you can setup the respective drivers /
utilities from the following place.
To open the setup files, click Start -> All Programs -> TOSHIBA ->
Applications and Drivers.

User’s Manual 1-15

The Grand Tour

This chapter identifies the various components of the computer - it is
recommended that you become familiar with each before you operate the
computer.

Legal Footnote (Non-applicable Icons)*1

For more information regarding Non-applicable Icons, please refer to the
Legal Footnotes section in Appendix H or click the *1 above.

Please handle your computer carefully to avoid scratching or damaging the
surface.

Front with the display closed

The following figure shows the computer’s front with its display panel in the
closed position.

System indicators

Chapter 2

SD Card slot

Figure 2-1 Front of the computer with display panel closed

User’s Manual 2-1

Left side

The Grand Tour

System indicators These LED indicators allow you to monitor the

status of various computer functions and are
described in more detail within the System

indicators section.

SD Card slot This slot can accommodate a single SD/SDHC

memory card in order to transfer data from
devices, such as digital cameras, onto your
computer.

The following figure shows the computer’s left side.

External monitor
port

Cooling vents

eSATA/USB
combo port

Volume control dial

Microphone jack

Universal Serial Bus
(USB 2.0) port

Headphone jack

External monitor
port

Security lock slot

Figure 2-2 The left side of the computer

This port provides 15-pin, analog VGA port.
This port allows you to connect an external

monitor to the computer.

There are no fastening screws for an external monitor cable on this
computer's external monitor port. However, external monitor cables which
have connectors with fastening screws can still be used.

Cooling vents The cooling vents help keep the processor from

overheating.

Do not block the cooling vents. Keep foreign metal objects, such as
screws, staples and paper clips, out of the cooling vents. Foreign metal
objects can create a short circuit, which can cause damage and fire,
possibly resulting in serious injury.

User’s Manual 2-2

The Grand Tour

Security lock slot A security cable can be attached to this slot and

then connected to a desk or other large object in
order to deter theft of the computer.

eSATA/USB combo
port

One eSATA/USB combo port, which complies to
the USB 2.0 standard, is provided on the left
hand side of the computer. The ports with the
icon ( ) has USB Sleep and Charge. This port
has eSATA (External Serial ATA) function.

Keep foreign metal objects, such as screws, staples and paper clips, out of
the eSATA/USB combo port. Foreign metal objects can create a short
circuit, which can cause damage and fire, possibly resulting in serious
injury.

Please note that it is not possible to confirm the operation of all functions of
all USB devices that are available. In view of this it may be noted that some
functions associated with a specific device might not operate properly.

Universal Serial Bus
(USB 2.0) port

One Universal Serial Bus port, which complies to
the USB 2.0 standard, is provided on the left
hand side of the computer.

Keep foreign metal objects, such as screws, staples and paper clips, out of
the USB connectors. Foreign metal objects can create a short circuit,
which can cause damage and fire, possibly resulting in serious injury.

Please note that it is not possible to confirm the operation of all functions of
all USB devices that are available. In view of this it may be noted that some
functions associated with a specific device might not operate properly.

Microphone jack A 3.5 mm mini microphone jack enables

connection of a three-conductor mini jack for
monaural microphone input.

Headphone jack A 3.5 mm mini headphone jack enables

connection of stereo headphones.

Volume control dial Use this dial to adjust the volume of the internal

stereo speaker and optional external stereo
headphones (if connected).

Move the Volume control dial to the left to
increase the volume and to the right to decrease
the volume.

User’s Manual 2-3

Right side

The following figure shows the computer’s right side.

Smart Card slot

Wireless
communication switch

LAN active indicator
(orange)

The Grand Tour

Link indicator
(green)

Optical disc drive

Figure 2-3 The right side of the computer

ExpressCard slot

Universal Serial Bus (USB 2.0) port

LAN jack

DC IN 15V
jack

DC IN 15V jack The AC adaptor connects to this jack in order to

power the computer and charge its internal
batteries. Please note that you should only use
the model of AC adaptor supplied with the
computer at the time of purchase - using the
wrong AC adaptor can cause damage to the
computer.

LAN jack This jack lets you connect to a LAN. The adaptor

has built-in support for Ethernet LAN (10
megabits per second, 10BASE-T), Fast Ethernet
LAN (100 megabits per second, 100BASE-TX)
and Gigabit Ethernet LAN (1000 megabits per
second, 1000BASE-T). Refer to Chapter 4,

Operating Basics, for details.

■ Do not connect any cable other than a LAN cable to the LAN jack. It

could cause damage or malfunction.

■ Do not connect the LAN cable to a power supply. It could cause

damage or malfunction.

Link indicator
(green)

This indicator glows green when the computer is
connected to a LAN and the LAN is functioning
properly.

LAN active indicator
(orange)

Universal Serial Bus
(USB 2.0) port

This indicator glows orange when data is being
exchanged between the computer and the LAN.

One Universal Serial Bus port, which complies to
the USB 2.0 standard, is provided on the right
hand side of the computer.

ExpressCard slot This slot allows you to install a single

ExpressCard device.

User’s Manual 2-4

The Grand Tour

Keep foreign metal objects, such as screws, staples and paper clips, out of
the ExpressCard slot. Foreign metal objects can create a short circuit,
which can cause damage and fire, possibly resulting in serious injury.

Wireless
communication
switch

Slide this switch to the left to turn off Wireless
LAN, Bluetooth

™

and Wireless WAN functions.

Slide it to the right to turn on the functions.
Only some models are equipped with Bluetooth,

Wireless LAN and Wireless WAN functions.

■ Do not use the Wireless LAN (Wi-Fi®) or Bluetooth functionalities near

a microwave oven or in areas subject to radio interference or magnetic
fields. Interference from a microwave oven or other source can disrupt
Wi-Fi or Bluetooth operation.

■ Turn all wireless functionalities off when near a person who may have a

cardiac pacemaker implant or other medical electric device. Radio
waves may affect pacemaker or medical device operation, possibly
resulting in serious injury. Follow the instruction of your medical device
when using any wireless functionality.

■ Always turn off wireless functionality if the computer is near automatic

control equipment or appliances such as automatic doors or fire
detectors. Radio waves can cause malfunction of such equipment,
possibly resulting in serious injury.

Optical disc drive The computer is configured with a DVD Super

Multi drive.

Smart Card slot This slot can accommodate a single Smart Card

device. Some models are equipped with a Smart
Card slot.

Keep foreign metal objects, such as screws, staples and paper clips, out of
the Smart Card slot. Foreign metal objects can create a short circuit, which
can cause damage and fire, possibly resulting in serious injury.

User’s Manual 2-5

Back

The following figure shows the computer’s back.

Underside

The following figure shows the underside of the computer. You should
ensure that the display is closed before the computer is turned over to
avoid causing any damage.

The Grand Tour

Battery pack

Figure 2-4 The back of the computer

Battery pack The battery pack provides power to the computer

when the AC adaptor is not connected. For more
detailed information on the use and operation of
the battery pack please refer to Chapter 6, Power

and Power-Up Modes.

Battery lock

Notch

Docking port

Notch

Battery release latch

Memory module slot

Figure 2-5 The underside of the computer

User’s Manual 2-6

The Grand Tour

Notches Notches on the computer engage hooks on the

TOSHIBA Express Port Replicator to ensure a
secure connection.

Docking port This port enables connection of an optional

TOSHIBA Express Port Replicator or a Slice
Expansion Battery described in Chapter 3,

Hardware, Utilities and Options.

■ Only the TOSHIBA Express Port Replicator can be used with this

computer. Do not attempt to use any other Port Replicator.

■ Keep foreign objects out of the docking port. A pin or similar object can

damage the computer's circuitry.

■ Do not use the computer's External monitor port, when connecting the

TOSHIBA Express Port Replicator to the computer.

Memory module slot The memory module slot allows for the

installation, replacement and removal of
additional memory module.

Refer to the Additional memory module section in
Chapter 3, Hardware, Utilities and Options.

Battery release latch Slide and hold this latch into its 'Unlock' position

in order to release the battery pack for removal.
For more detailed information on removing the
battery pack please refer to Chapter 6, Power

and Power-Up Modes.

Battery lock Slide the battery lock to release the battery pack

ready for removal.

User’s Manual 2-7

Front with the display open

This section shows the computer with the display panel open. In order to
open the display, lift the display panel up and position it at a comfortable
viewing angle for you.

Wireless LAN antennas (Not shown)

Display
screen

Display hinge

Stereo speaker
(Left)

Power button

LCD Sensor switch
(Not shown)

Wireless WAN antennas
(Not shown)

TOSHIBA Assist
button

TOSHIBA
Presentation button

Figure 2-6 The front of the computer with the display panel open

Wireless LAN antenna
(Not shown)

Web Camera

Web Camera LED

Display hinge

Stereo speaker
(Right)

Microphone

Touch Pad

Keyboard

Fingerprint Sensor

Bluetooth antenna
(Not shown)

The Grand Tour

Touch Pad
control buttons

Display hinges The display hinges allow the display panel to be

position at a variety of easy-to-view angles.

Display screen Please be aware that, when the computer is

operating on the AC adaptor, the image
displayed on the internal screen will be
somewhat brighter than when it operates on
battery power. This difference in brightness
levels is intended to save power when operating
on batteries. For more information on the
computer's display, please refer to the Display

Controller and Video mode section in Appendix

B.

Web Camera LED

The Web Camera LED glows when the Web
Camera is operating.

User’s Manual 2-8

The Grand Tour

Web Camera Web Camera is a device that allows you to

record video or take photographs with your
computer. You can use it for video chatting or
video conferences using a communication tool
such as Windows Live Messenger. TOSHIBA
Web Camera Application will help you to add
various video effects to your video or photograph.

Enables the transmission of video and use of
video chat via the internet using specialized
applications.

The effective pixel count for this web camera is

0.3 million (maximum photograph size: 640x480
pixels).

Some models are equipped with a Web Camera.
Please refer to the Web Camera section in

Chapter 4, Operating Basics.

Touch Pa d The Touch Pad located in the center of the palm

rest is used to control the movement of the on­screen pointer. For more information, please
refer to the Using the Touch Pad section in
Chapter 4, Operating Basics.

Touch Pad control
buttons

The control buttons located below the Touch Pad
allow you to select menu items or manipulate text
and graphics as designated by the on-screen
pointer.

Microphone A built-in microphone allows you to import and

record sounds for your application - please refer
to the Sound System section in Chapter 4,
Operating Basics for more information.

Keyboard The internal keyboard provides the embedded

numeric overlay keys, dedicated cursor control
overlay keys, and Keys. The keyboard
is compatible with the IBM

®

enhanced keyboard.

Refer to Chapter 5, The Keyboard, for details.

Stereo speakers The speakers emit sound generated by your

software as well as audio alarms, such as low
battery condition, generated by the system.

Power button Press this button to turn the computer's power on

and off.

TOSHIBA Assist
button

Press this button to launch the program
automatically. When power-off, Sleep Mode and
Hibernation Mode, press this button to start the
computer and launch the program.

User’s Manual 2-9

The Grand Tour

TOSHIBA
Presentation button

The TOSHIBA Presentation button has the same
functionality as the Connect display button in the
Mobility Center.

Fingerprint Sensor This sensor enables you to enroll and recognize

a fingerprint.
For detailed information on Fingerprint Sensor,

refer to Chapter 4, Using the Fingerprint Sensor.

LCD Sensor switch This switch senses when the display panel is

either closed or opened and activates the Panel
Power Off/On feature as appropriate. For
example, when you close the display panel the
computer enters Hibernation Mode and shuts
itself down and then, when you next open the
display, the computer will automatically start up
and return you to the application you were
previously working on.

You can specify within the Power Options. To
access it, click Start -> Control Panel -> System
and Security -> Power Options.

Do not put any magnetic objects close to this switch as they may cause the
computer to automatically enter Hibernation Mode and shut down even if
the Panel Power Off feature is disabled.

Bluetooth antenna Some computers in this series are equipped with

a Bluetooth antenna.

Wireless LAN
antennas

Wireless WAN
antennas

User’s Manual 2-10

Some computers in this series are equipped with
the Wireless LAN antennas.

Some computers in this series are equipped with
the Wireless WAN antennas.

Indicators

System indicators

The Grand Tour

This section explains indicator functions.

The LED system indicators for specific computer operations glow when
those operations are in progress.

Figure 2-7 System indicators

DC IN The DC IN indicator normally glows green when

power is being correctly supplied from the AC
power adaptor. However, If the output voltage
from the adaptor is abnormal, or if the computer's
power supply malfunctions, this indicator will
flash orange.

Power The Power indicator normally glows green when

Battery The Battery indicator shows the condition of the

2nd battery The 2nd battery indicator shows the condition of

Hard Disk Drive The Hard Disk Drive indicator glows green

SD Card The SD Card indicator glows green when the

the computer is turned on. However, if you turn
the computer off into Sleep Mode, this indicator
will flash orange - approximately one second on,
two seconds off - both while the system is
shutting down and while it remains turned off.

battery's charge - green indicates the battery is
fully charged, orange indicates the battery is
charging, and flashing orange indicates a low
battery condition. Please refer to Chapter 6,

Power and Power-Up Modes for more

information on this feature.

the Slice Expansion Battery's charge - green
indicates the Slice Expansion Battery is fully
charged, orange indicates the Slice Expansion
Battery is charging, and flashing orange indicates
a low battery condition.

Please refer to Chapter 6, Power and Power-Up

Modes for more information on this feature.

whenever the computer is accessing the built-in
hard disk drive.

computer is accessing the device in the SD Card
slot.

User’s Manual 2-11

The Grand Tour

Wireless
communication

The Wireless communication indicator glows
orange when the Bluetooth and Wireless LAN
functions are turned on.

Only some models are equipped with Bluetooth
and Wireless LAN functions.

Wireless WAN The Wireless WAN indicator glows or blinks blue

when the Wireless WAN function is on.
The indicator will glow or blink in order to indicate

the connection status of the Wireless WAN
function.

A Wireless WAN module must be installed to use
this function. Some models are equipped with a
Wireless WAN module.

Keyboard indicators

The following figures show the positions of the CAPS LOCK indicator and
the keypad overlay indicators which show the following conditions:

■ When the CAPS LOCK indicator glows, the keyboard will produce

capitals when any letter is typed.

■ When the Arrow Mode indicator glows, the keypad overlay allows you to

use cursor functions.

■ When the Numeric Mode indicator glows, the keypad overlay allows

you to enter numbers.

CAPS LOCK indicator

Figure 2-8 CAPS LOCK indicator

CAPS LOCK This indicator glows green when letter keys are

locked into their uppercase format.

User’s Manual 2-12

The Grand Tour

Arrow mode
indicator

Arrow mode When the Arrow mode indicator lights green,

Numeric mode When the Numeric mode indicator lights green,

Optical disc drives

The computer is installed with a DVD Super Multi drive. A Serial ATA
interface controller is used for CD/DVD-ROM operation. When the
computer is accessing a CD/DVD, an indicator on the drive glows.

For information on loading and unloading discs refer to the Using optical

disc drives section in Chapter 4, Operating Basics.

Numeric mode
indicator

Figure 2-9 Keypad overlay indicators

you can use the gray labeled keys on the keypad
overlay as cursor keys. Please refer to the

Keypad overlay section in Chapter 5, The

Keyboard for more information.

you can use the gray labeled keys on the keypad
overlay for number entry. Please refer to the

Keypad overlay section in Chapter 5, The

Keyboard for more information.

Region codes for DVD drives and media

DVD Super Multi drives and their associated media are manufactured
according to the specifications of six marketing regions. When you
purchase DVD-Video, make sure it matches your drive, otherwise it will not
play properly.

Code Region

1 Canada, United States

2 Japan, Europe, South Africa, Middle East

3 Southeast Asia, East Asia

4 Australia, New Zealand, Pacific Islands, Central

America, South America, Caribbean

User’s Manual 2-13

The Grand Tour

5 Russia, Indian Subcontinent, Africa, North Korea,

6 China

Mongolia

Writable discs

This section describes the types of writable CD/DVD discs. Check the
specifications of your drive to see the types of discs it can write. Use
TOSHIBA Disc Creator to write compact discs. Refer to Chapter 4,

Operating Basics.

CDs

■ CD-R discs can be written only once. The recorded data cannot be

erased or changed.

■ CD-RW discs including multi speed CD-RW discs, high-speed CD-RW

discs and ultra-speed CD-RW discs can be recorded more than once.

DVDs

■ DVD-R, DVD+R, DVD-R (Dual Layer) and DVD+R (Double Layer) discs

can be written only once. The recorded data cannot be erased or
changed.

■ DVD-RW, DVD+RW and DVD-RAM discs can be recorded more than

once.

Formats

The drives support the following formats.

DVD Super Multi drive Double Layer

The drive supports the formats CD-ROM, DVD-ROM, DVD-Video, CD-DA,
CD-Text, Photo CD
CD-ROM XA Mode 2 (Form1, Form2), Enhanced CD (CD-EXTRA),
Addressing Method 2, CD-R, CD-RW, DVD-R, DVD-R DL, DVD-RW,
DVD+R, DVD+R DL, DVD+RW and DVD-RAM.

Some types and formats of DVD-R DL and DVD+R DL discs may be
unreadable.

User’s Manual 2-14

TM

(single/multi-session), CD-ROM Mode 1, Mode 2,

DVD Super Multi drive Double Layer

The full-size DVD Super Multi drive module lets you record data to
rewritable CD/DVDs as well as run either 12 cm (4.72") or 8cm (3.15")
CD/DVDs without using an adaptor.

The read speed is slower at the center of a disc and faster at the outer
edge.

DVD read 8 speed (maximum)
DVD-R write 8 speed (maximum)
DVD-R DL write 4 speed (maximum)
DVD-RW write 6 speed (maximum)
DVD+R write 8 speed (maximum)
DVD+R DL write 4 speed (maximum)
DVD+RW write 8 speed (maximum)
DVD-RAM write 5 speed (maximum)
CD read 24 speed (maximum)
CD-R write 24 speed (maximum)
CD-RW write 16 speed (maximum, Ultra-speed media)

AC adaptor

The AC adaptor can automatically adjust to any voltage ranging from 100 to
240 volts and to a frequency of either 50 or 60 hertz, enabling you to use
this computer in almost all country/region. The adaptor converts AC power
to DC power and reduces the voltage supplied to this computer.

To recharge the battery, simply connect the AC adaptor to a power source
and to the computer. Please refer to Chapter 6, Power and Power-Up

Modes for further information.

The Grand Tour

Figure 2-10 The AC adaptor (2-pin plug)

User’s Manual 2-15

The Grand Tour

Figure 2-11 The AC adaptor (3-pin plug)

■ Depending on the model in question, either a 2-pin or 3-pin

adaptor/power lead will be bundled with the computer.

■ Do not use a 3-pin to 2-pin conversion plug.

■ The supplied power cord conforms to safety rules and regulations in

the region the product is bought and should not be used outside of this
region. In order to use the adaptor/computer in other regions, you
should please buy a power cord that conforms to the safety rules and
regulations in that particular region.

Always use the TOSHIBA AC adaptor that was included with your
computer, or use AC adaptors specified by TOSHIBA to avoid any risk of
fire or other damage to the computer. Use of an incompatible AC adaptor
could cause fire or damage to the computer possibly resulting in serious
injury. TOSHIBA assumes no liability for any damage caused by use of an
incompatible adaptor.

User’s Manual 2-16

Chapter 3

Hardware, Utilities and Options

Hardware

This section describes the hardware of your computer.
The actual specifications may vary depending on the model you

purchased.

Processor

CPU Your computer is equipped with one processor

and processor type varies depending on model.
To check which type of processor is included in

your model, open the TOSHIBA PC Diagnostic
Tool Utility by clicking Start -> All programs ->
TOSHIBA -> Utilities -> PC Diagnostic Tool.

Some models in this series use Intel® Centrino® 2 processor technology
which is based on three separate components, the Intel
processor, Intel
Chipset.

®

Wi-Fi Link 5100AGN and the Intel® GS45 Express

®

Core™ 2 Duo

Legal Footnote (CPU)*2

For more information on the CPU, please refer to the Legal Footnotes
section in Appendix H or Click the *2 above.

User’s Manual 3-1

Memory

Hardware, Utilities and Options

Memory slots 1,024 or 2,048MB memory modules can be

Video RAM The memory in a computer's graphics adaptor,

If your computer is configured with more than 3 GB memory, the memory
might be displayed as approximately 3 GB only (depending on the
computer’s hardware specifications).

This is correct because the operating system usually displays the available
memory instead of the physical memory (RAM) built into the computer.

Various system components (like the video adapter’s GPU and PCI
devices like Wireless LAN, etc.) require their own memory space. Since a
32-bit operating system cannot address more than 4 GB of memory, these
system resources overlap the physical memory. It is a technical limitation
that the overlapped memory is not available to the operating system. Even
though some tools might display the actual physical memory built into your
computer, the memory available to the operating system will still be
approximately 3 GB only.

installed in the computer's two memory slots for a
maximum of 4,096MB system memory.

This computer can be equipped with memory
modules of a maximum size of 4,096MB. The
actual amount of useable system memory will be
less than the installed memory modules.

used to store the image displayed on a bitmap
display.

The amount of Video RAM available is
dependent on the computer's system memory.

Start -> Control Panel -> Appearance and
Personalization -> Display -> Adjust
resolution.

The amount of Video RAM can be verified by
clicking the Advanced Settings button in the
Screen Resolution window.

Legal Footnote (Memory (Main System))*3

For more information regarding Memory (Main System), please refer to the
Legal Footnotes section in Appendix H or click the *3 above.

Power

Battery pack The computer is powered by one rechargeable

User’s Manual 3-2

lithium-ion battery pack.

Hardware, Utilities and Options

Legal Footnote (Battery Life)*4

For more information regarding Battery Life, please refer to the Legal
Footnotes section in Appendix H or click the *4 above.

RTC battery The internal RTC battery backs up the Real Time

Clock (RTC) and calendar.

AC adaptor The AC adaptor provides power to the system

and recharges the batteries when they are low. It
comes with a detachable power cord which will
either have a 2-pin or 3-pin plug enclosure.

As the AC adaptor is universal, it can receive a
range of AC voltages from 100 to 240 volts,
however you should note that the output current
varies among different models. Using the wrong
adaptor can damage your computer. Refer to the

AC adaptor section in Chapter 2, The Grand

To ur .

Disks

Hard disk drive or
Solid state drive

This computer is equipped with one of the
following hard disk drive (HDD) types. The
capacity of each hard disk drive model is
different.

Some models are equipped with a "Solid State
Drive (SSD)" instead of a hard disk drive.

■ HDD

■ 80GB

■ 120GB

■ 160GB

■ 200GB

■ 250GB

■ 320GB

■ SSD

■ 64GB

■ 128GB

Please note that part of the hard disk or Solid
state drive's overall capacity is reserved as
administration space. Additional HDD/SSD drive
sizes may be introduced.

User’s Manual 3-3

Hardware, Utilities and Options

■ Additional hard disk drive sizes may be introduced.

■ In this manual, the word "HDD" or "Hard disk drive" also refers to the

SSD unless otherwise stated.

■ SSD is a large-capacity storage media which uses Solid-State Memory

in place of a magnetic disk of the hard disk.

Under certain unusual conditions of prolonged non-use and/or exposure to
high temperatures, the SSD may be vulnerable to data retention errors.

Legal Footnote (Hard Disk Drive (HDD) Capacity)*5

For more information regarding Hard Disk Drive (HDD) Capacity, please
refer to the Legal Footnotes section in Appendix H or click the *5 above.

Optical disc drive

Drive The following optical disc drive is pre-installed in

this computer.

■ DVD Super Multi drive Double Layer

2.6GB and 5.2GB DVD-RAM media cannot be read from or written to.

Display

The computer's internal display panel supports high-resolution video
graphics and can be set to a wide range of viewing angles for maximum
comfort and readability.

Display panel 14.1” TFT LCD screen, 16 million colors, with

one of the following resolutions:

■ WXGA, 1280 horizontal x 800 vertical pixels

■ WXGA+, 1440 horizontal x 900 vertical pixels

Legal Footnote (LCD)*6

For more information regarding the LCD, please refer to the Legal
Footnotes section in Appendix H or click the *6 above.

Graphics controller The graphics controller maximizes display

performance. Refer to Display Controller and

Video mode section in Appendix B for more

information.

User’s Manual 3-4

Hardware, Utilities and Options

Legal Footnote (Graphics Processor Unit ("GPU"))*7

For more information regarding the Graphics Processor Unit ("GPU"),
please refer to the Legal Footnotes section in Appendix H or click the *7
above.

Sound

Sound system The integrated sound system provides support

for the computer's internal speakers and
microphone, as allowing an external microphone
and headphones to be connected via the
appropriate jacks.

Multimedia

Web Camera Web Camera is a device that allows you to

record video or take photographs with your
computer. You can use it for video chatting or
video conferences using a communication tool
such as Windows Live Messenger. TOSHIBA
Web Camera Application will help you to add
various video effects to your video or photograph.

Some models are equipped with a Web Camera.
Please refer to the Web Camera section in

Chapter 4, Operating Basics.

Communications

LAN The computer has built-in support for Ethernet

LAN (10 megabits per second, 10BASE-T), Fast
Ethernet LAN (100 megabits per second,
100BASE-TX) and Gigabit Ethernet LAN (1000
megabits per second, 1000BASE-T).

Bluetooth Some computers in this series have Bluetooth

wireless communication function which
eliminates the need for cables between
electronic devices such as computers, printers
and mobile phones. When it is enabled,
Bluetooth provides the wireless personal area
network environment which is safe and
trustworthy, that is quick and easy.

Wireless LAN Some computers in this series are equipped with

a Wireless LAN module that is compatible with
other LAN systems based on Direct Sequence
Spread Spectrum/Orthogonal Frequency Division
Multiplexing radio technology that complies with
the IEEE 802.11 Standard.

User’s Manual 3-5

Legal Footnote (Wireless LAN)*8

For more information regarding Wireless LAN, please refer to the Legal
Footnotes section in Appendix H or click the *8 above.

Wireless WAN A Wireless WAN card supports HSPA and

Special features

The following features are either unique to TOSHIBA computers or are
advanced features which make the computer more convenient to use.

Access each function using the following procedures.
*1 To access the Power Options, click Start -> Control Panel -> System

and Security -> Power Options.

Hardware, Utilities and Options

provides faster communications than previous
Wireless WAN cards.

Some computers in this series are equipped with
a Wireless WAN card.

TOSHIBA Assist
button

Press this button to launch the program
automatically. When power-off, Sleep Mode and
Hibernation Mode, press this button to start the
computer and launch the program.

TOSHIBA
Presentation button

The TOSHIBA Presentation button has the same
functionality as the Connect display button in the
Mobility Center.

Hot keys Hot keys are specific key combinations that let

you quickly change the system configuration
directly from the keyboard without running a
system program.

Display automatic
power off

*1

This feature automatically cuts off power to the
computer's display panel when there is no
keyboard input for a specified time, with power
being restored the next time a key is pressed.
This can be specified in the Power Options.

HDD automatic
power off

*1

This feature automatically cuts off power to the
hard disk drive when it is not accessed for a
specified time, with power being restored when
the hard disk drive is next accessed. This can be
specified in the Power Options.

System automatic
Sleep/Hibernation

*1

Mode

This feature automatically shuts down the system
into either Sleep Mode or Hibernation Mode when
there is no input or hardware access for a
specified time. This can be specified in the Power
Options.

User’s Manual 3-6

Hardware, Utilities and Options

Keypad overlay A ten-key numeric keypad is integrated into the

keyboard. Please refer to the Keypad overlay
section in Chapter 5, The Keyboard, for
information on using this feature.

Power on password Two levels of password security, supervisor and

user, are available to prevent unauthorized
access to your computer.

Instant security A specific hot key function automatically locks the

system providing data security.

Intelligent power
supply

*1

A microprocessor in the computer's intelligent
power supply detects the battery's charge,
automatically calculates the remaining battery
capacity and protects electronic components
from abnormal conditions such as a voltage
overload from the AC adaptor. This can be
specified in the Power Options.

*1

Battery save mode

This feature lets you configure the computer in
order to save battery power. This can be
specified in the Power Options.

Panel power on/off

*1

This feature automatically turns power to the
computer off when the display panel is closed,
and turns it back on when the display panel is
opened. This can be specified in the Power
Options.

Low battery
automatic

Hibernation Mode

When battery power is exhausted to the point that
computer operation cannot be continued, the

*1

system automatically enters Hibernation Mode
and shuts itself down. This can be specified in the
Power Options.

Heat dispersal

*1

To protect against overheating, the processor has
an internal temperature sensor so that, if the
computer's internal temperature rises to a certain
level, the cooling fan is turned on or the
processing speed is lowered. This can be
specified in the Power Options.

TOSHIBA HDD
Protection

This feature uses the acceleration sensor built in
the computer to detect vibration and shocks, and
automatically moves the hard disk drive's
read/write head to a safe position in order to
reduce the risk of damage that could be caused
by head-to-disk contact. Refer to the Using the

Hard Disk Drive (HDD) Protection section in

Chapter 4, Operating Basics, for more details.

User’s Manual 3-7

Hardware, Utilities and Options

■ The TOSHIBA HDD Protection function does not guarantee that the

hard disk drive will not be damaged.

■ TOSHIBA HDD Protection cannot be used in models that are equipped

with SSD.

Hibernation Mode This feature lets you turn off the power to the

computer without exiting from your software. The
contents of main memory are automatically
saved to the hard disk drive so that when you
next turn the power on again, you can continue
working right where you left off. Refer to the

Turning off the power section in Chapter 1,

Getting Started, for more details.

Sleep Mode If you have to interrupt your work, you can use

this feature to allow you to turn off power to the
computer without exiting from your software.
Data is maintained in the computer's main
memory so that when you next turn on the power,
you can continue working right where you left off.

USB Sleep and
Charge function

This feature allows you to charge USB­compatible external devices such as mobile
phones or portable digital music players via the
USB port when your computer is in Sleep Mode,
Hibernation Mode or in the shutdown state.

This function is worked by the USB Sleep and
Charge Utility. For more information, please refer
to the Using the TOSHIBA USB Sleep and

Charge Utility section in Chapter 4, Operating

Basics.

Legal Footnote (USB Sleep and Charge)*9

For more information regarding USB Sleep and Charge, please refer to the
Legal Footnotes section in Appendix H or click the *9 above.

User’s Manual 3-8

Hardware, Utilities and Options

USB Wakeup
function

TOSHIBA PC Health
Monitor

This function restores the computer from Sleep
Mode depending on the external devices
connected to the USB ports.

For example, if a mouse or USB keyboard is
connected to a USB port, moving the
mouse/keyboard will wakeup the computer.

The "USB Wakeup function" operates under
Windows 7 operating system and it works for all
USB ports.

The TOSHIBA PC Health Monitor application
proactively monitors a number of system
functions such as power consumption, battery
health and the system cooling, informing you of
significant system conditions. This application
recognizes the system and individual component
serial numbers, and will track specific activities
related to the computer and their usage.

Refer to Appendix G, TOSHIBA PC Health

Monitor.

TOSHIBA Value Added Package

This section describes the TOSHIBA Component features pre-installed on
the computer.

TOSHIBA Power
Saver

TOSHIBA Power Saver provides you with the
features of more various power supply
managements.

TOSHIBA Button
Support

TOSHIBA Zooming
Utility

TOSHIBA PC
Diagnostic Tool

User’s Manual 3-9

This utility controls the following computer button
functions.

■ TOSHIBA Assist

■ TOSHIBA Presentation

The starting application from the button can be
changed.

This utility allows you to enlarge or reduce the
icon size on the Windows Desktop, or the zoom
factor associated with specific supported
applications.

The TOSHIBA PC Diagnostic Tool will display
basic system configuration information and allow
the functionality of some of the computer's built­in hardware devices to be tested.

Hardware, Utilities and Options

TOSHIBA Password
Utility

The TOSHIBA Password utility allows you to set
a password in order to restrict access to the
computer.

TOSHIBA Flash
Cards

The TOSHIBA Flash Cards provide a quick way
to modify selected system functions and to
launch applications.

■ Hot key function

■ TOSHIBA utility launcher function

HW Setup This utility allows you to customize your

hardware settings according to the way you work
with the computer and the peripherals you use.

TOSHIBA
Accessibility

The TOSHIBA Accessibility utility provides
support to movement impaired users when they
need to use the TOSHIBA Hot-key functions. In
use, the utility allows you to make the FN key
'sticky', that is you can press it once, release it,
and they press one of the 'Function' keys in
order to access its specific function. When set,
the FN key will remain active until another key is
pressed.

User’s Manual 3-10

Utilities and Applications

This section describes the pre-installed utilities that come with the
computer and details how to start them. For further information on their
operation, please refer to each utility's online manual, help files or
README.TXT file.

Fingerprint Utility This product has a fingerprint utility installed for

TOSHIBA Face
Recognition

Hardware, Utilities and Options

the purpose of enrolling and recognizing
fingerprints which can then be linked to a
username and password in order to remove the
need to input these details from the keyboard.
Just by swiping an enrolled finger against the
fingerprint sensor, the following functions will be
enabled:

■ Logon to Windows and access a security

enabled homepage through Internet Explorer.

■ Files and folders can be encrypted/decrypted

and third party access to them is prevented.

■ Disable the password-protected screen-saver

when returning from a power-saving mode
such as Sleep Mode.

■ Authentication of the User Password (and, if

applicable, the HDD(Hard Disk Drive)
Password) when booting up the computer
(Boot Authentication).

■ Single Sign-on feature.

TOSHIBA Face Recognition uses a face
verification library to verify the face data of users
when they log in to Windows. If the verification is
successful, the user will be logged into Windows
automatically. The user can thus avoid having to
enter a password or the like, which makes the
login process easier.

TOSHIBA Face Recognition can only be used in models that have a Web
Camera installed.

User’s Manual 3-11

Hardware, Utilities and Options

TOSHIBA DVD
Player

This software is provided for playback of DVD
Video.

It has an on-screen interface and functions. Click

Start -> All Programs -> TOSHIBA DVD
PLAYER -> TOSHIBA DVD PLAYER.

Refer to the TOSHIBA DVD PLAYER section in
Chapter 4, Operating Basics, for more details.

For details on how to use TOSHIBA DVD
PLAYER, see the help file.

■ Frame dropping, audio skipping or out of synch audio and video may

occur during playback of some DVD Video titles.

■ Make sure to connect the computer's AC adaptor when playing a DVD

Video. Power-saving features may interfere with smooth playback.

Bluetooth Stack for
Windows by Toshiba

This software enables communication between
the computer and external Bluetooth devices
such as printers and mobile phones.

Bluetooth functions cannot be used in models that do not have a Bluetooth
module installed.

TOSHIBA SD
Memory Boot Utility

The TOSHIBA SD Memory Boot Utility allows
you to create a bootable SD memory card to start
the system. You can boot TOSHIBA SD Memory
Boot Utility from the menu bar as follows. Click
Start -> All Programs -> TOSHIBA -> Utilities

-> SD Memory Boot Utility.

■ SD Memory Card Format Utility and other SD functions are packaged

into TOSHIBA SD Memory Utilities.

■ Only the SD memory card can create a bootable SD memory card.

TOSHIBA SD
Memory Card Format

This utility allows you to format an SD/SDHC
memory card by the SD standard format.

TOSHIBA Assist TOSHIBA Assist is a graphical user interface that

provides access to specific tools, utilities and
applications that make the use and configuration
of the computer easier.

User’s Manual 3-12

Hardware, Utilities and Options

TOSHIBA ConfigFree TOSHIBA ConfigFree is a suite of utilities that

improve the ease and control of communication
devices and network connections, help in the
identification of communication problems and
allow the creation of profiles if you need to switch
between different locations and communication
networks. To access this utility, click Start -> All

Programs -> TOSHIBA -> ConfigFree.

TOSHIBA Mic Effect TOSHIBA Mic Effect provides you the Echo

Canceller and the Microphone Array functions.
For more instructions for this software, refer to

the Sound System section in Chapter 4,
Operating Basics.

TOSHIBA eco Utility This PC is equipped with "eco mode". This mode

slightly lowers performance of some devices to
reduce electric power consumption. You can
realize measurable power savings by using it
continuously. TOSHIBA eco Utility helps you
monitor your power savings by showing
approximate real time power consumption.

Furthermore, it shows approximate accumulated
power consumption and approximate
accumulated power savings when using eco
mode daily, weekly and monthly. You can track
power savings by using eco mode continuously.

To start this utility, click Start -> All Programs ->

TOSHIBA -> Utilities -> eco Utility.

TOSHIBA Disc
Creator

You can create CD's and DVD's in a number of
formats including audio CD's that can be played
on a standard CD player, and data CD's/DVD's
which can store copies of the files and folders on
your computer's hard disk drive. This software
can be used on models with a DVD Super Multi
drive.

To start this utility, click Start -> All Programs ->

TOSHIBA -> CD&DVD Applications -> Disc
Creator.

TOSHIBA DVD-RAM
Utility

This utility has the function of Physical Format
and Write-Protect to DVD-RAM. This utility is
contained the setup module of TOSHIBA Disc
Creator. To start this utility, click Start -> All

Programs -> TOSHIBA -> CD&DVD
Applications -> DVD-RAM Utility.

User’s Manual 3-13

Hardware, Utilities and Options

TOSHIBA HDD/SSD
Alert

TOSHIBA Service
Station

Windows Mobility
Center

This utility includes wizard functions to monitor
the Disk Drive operating status and execute the
system backup.

To access this utility, click Start -> All Programs

-> TOSHIBA -> Utilities -> HDD SSD Alert.

This application allows your computer to
automatically search for TOSHIBA software
updates or other alerts from TOSHIBA that are
specific to your computer system and its
programs. When enabled, this application
periodically transmits to our servers a limited
amount of system information, which will be
treated in strict accordance with the rules and
regulations as well as applicable data protection
law.

To access this utility, click Start -> All Programs

-> TOSHIBA -> Utilities -> Service Station.

Mobility Center is a utility for accessing several
mobile PC settings quickly in one window. A
default maximum of eight tiles are provided by
the operating system, and the additional two tiles
are added to your Mobility Center.

■ Lock Computer :

This can be used to lock your computer
without turning it off. This has the same
function as selecting Lock from the Start
menu (click Start, point to the arrow icon

and then select Lock from

the menu).

■ TOSHIBA Assist :

This can be used to open TOSHIBA Assist if
it is already installed in your computer.

User’s Manual 3-14

Hardware, Utilities and Options

TOSHIBA USB Sleep
and Charge Utility

Trusted Platform
Module (TPM)

This utility is able to either enable or disable the
USB Sleep and Charge function.

This utility shows the positions of USB ports that
support the USB Sleep and Charge function and
displays the battery's remaining capacity.

To start this utility, click Start -> All Programs ->

TOSHIBA -> Utilities -> USB Sleep and
Charge.

The TPM (Trusted Platform Module) is a security
encryption device for the hard disk drive. To use
TPM:

1. Enable TPM through the BIOS setup by the
following steps:

1. Turn on the computer while pressing the

ESC key.

2. Press the F1 key when directed.

3. Press the PGDN key.

4. Press the down arrow key until TPM is

highlighted, then press the space bar to
change the TPM status to Enabled.

5. Press the Y key to save the changes.

6. Press END and then press the Y key to

accept the changes. The computer will
restart.

Some models may have Hide TPM as an
option on the BIOS setup screen. If your
system shows Hide TPM, it should be set to
No before you set TPM to Enabled.
Otherwise, you will not be able to change
TPM.

2. Install Infineon TPM Software Professional

Package from Start-> All Programs ->
TOSHIBA -> Applications and Drivers.

3. Perform the TPM configuration. We
recommend that you read the help file of
Infineon TPM software before you do the
TPM initialization. You may refer to the Help
from Start -> All Programs -> Infineon
Security Platform Solution -> Help.

User’s Manual 3-15

Optional devices

To connect optional devices (such as USB device or External monitor) to
the computer, be sure to check the shape and orientation of the connector
before connecting.

Optional devices can expand the computer's capabilities and its versatility.
This section describes the connection or installation of the following
devices:

Cards/memory

■ ExpressCard

■ Smart Card

■ Secure Digital™ (SD) Card (SD memory card, SDHC memory card,

miniSD Card, microSD Card)

■ Additional memory module

Peripheral devices

■ External monitor

■ USB FDD Kit

■ eSATA

■ TOSHIBA Express Port Replicator

Hardware, Utilities and Options

Other

■ Security lock

ExpressCard

The computer is equipped with a single ExpressCard slot into which any
ExpressCard device that meets industry standards, either manufactured by
TOSHIBA or another vendor, can be installed. The slot supports hot plug
connection and utilizes the PCI Express interface that supports the reading
and writing of data at a theoretical maximum rate of 2.5Gbps.

When inserted in the ExpressCard slot, some ExpressCards may block the
optical disc drive tray and prevent it from opening. If this occurs please
remove the ExpressCard each time you wish to open or close the optical
disc drive tray.

Inserting an ExpressCard

The Windows hot-install feature allows you to insert ExpressCards while
the computer is turned on.

Do not insert an ExpressCard while the computer is in Sleep Mode or
Hibernation Mode as you may find that some cards do not work properly.

User’s Manual 3-16

Hardware, Utilities and Options

To insert an ExpressCard, follow the steps as detailed below:

1. Press the Dummy card in order to eject the Dummy card partially out of
the computer.

2. Grasp the Dummy card and draw it.

3. Insert the ExpressCard into the ExpressCard slot on the side of the
computer.

4. Press the ExpressCard gently to ensure a firm connection is made.

ExpressCard slot

ExpressCard

Figure 3-1 Inserting the ExpressCard

5. After inserting the ExpressCard you should refer to its documentation
and also check the configuration in Windows in order to ensure that it is
correct.

Removing an ExpressCard

To remove an ExpressCard, follow the steps as detailed below.

1. Open the Safely Remove Hardware icon on the Windows Taskbar.

2. Point to ExpressCard and click the left Touch Pad control button.

3. Press the ExpressCard in order to eject the ExpressCard partially out of
the computer.

4. Grasp the ExpressCard and remove it.

ExpressCard

Figure 3-2 Removing the ExpressCard

5. Insert the Dummy card into the ExpressCard slot.

When you do not use a ExpressCard, please be sure to insert a Dummy
card.

User’s Manual 3-17

Hardware, Utilities and Options

Smart Card

A Smart Card is a credit card sized plastic card. An extremely thin
integrated circuit (IC chip) is embedded into the card on which information
can be recorded. These cards can be used for a wide variety of
applications including telephone related and electronic monetary payments.

This section contains information on the proper use of the Smart Card slot,
and it is strongly recommended that you read it before operating the
computer.

Some models are equipped with a Smart Card slot.

Your computer supports ISO7816-3 asynchronous cards (support
protocols are T=0 and T=1) with a working voltage of 5V.

Inserting a Smart Card

The Smart Card slot is located on the right side of the computer. The
Windows hot-install feature allows you to insert a Smart Card while the
computer is turned on.

To install a Smart Card, follow the steps as detailed below:

1. Insert the Smart Card into the Smart Card slot with the metal
connectors facing up.

2. Press the Smart Card gently to ensure a firm connection is made. The
computer will identify the Smart Card and display an icon in the
Windows Taskbar.

■ When inserting a Smart Card into the Smart Card slot, make sure to

confirm that the card is oriented correctly before inserting.

■ Insert the Smart Card until it reaches the end of the Smart Card slot.

There will be about 2cm of the Smart Card sticking out of the Smart
Card slot. Do not attempt to insert it further.

■ Always remove the Smart Card from the Smart Card slot before moving

the computer.

■ Remove the Smart Card after use.

Failure to follow these instructions may result in damage to the computer
and/or damage to the Smart Card.

Smart Card

Figure 3-3 Inserting a Smart Card

User’s Manual 3-18

Hardware, Utilities and Options

3. After inserting the Smart Card, you should refer to its documentation
and also check the configuration in Windows in order to ensure that it is
correct.

Removing a Smart Card

To remove a Smart Card, follow the steps as detailed below:

1. Open the Safely Remove Hardware icon on the Windows Taskbar.

■ Before removing the Smart Card, confirm that the Smart Card is not

working with any program or system.

■ Be careful not to bend the Smart Card while removing it from the

computer.

2. Point to Smart Card and click the left Touch Pad control button.

3. Grasp the Smart Card and remove it.

Smart Card

Figure 3-4 Removing a Smart Card

SD/SDHC memory card

Set the SD Card type SD memory cards and SDHC memory cards in the
SD Card slot.

SD/SDHC memory cards let you easily transfer data from devices, such as
digital cameras and Personal Digital Assistants, that use SD/SDHC
memory card flash-memory. The cards have a high level of security and
copy protection features.

Keep foreign objects out of the SD Card slot. Never allow metal objects,
such as screws, staples and paper clips, to enter the computer or
keyboard. Foreign metal objects can create a short circuit, which can
cause computer damage and fire, possibly resulting in serious injury.

Points to note about the SD/SDHC memory card

SD/SDHC memory cards comply with SDMI (Secure Digital Music
Initiative), which is a technology adopted to prevent unlawful copy or
playback of digital music. For this reason, you cannot copy or playback
protected material on another computer or other device, and you may not
reproduce any copyrighted material except for your personal enjoyment.

User’s Manual 3-19

Hardware, Utilities and Options

Below is a simple explanation for distinguishing SD memory cards from
SDHC memory cards.

■ SD and SDHC memory cards appear the same externally. However, the

logo on SD and SDHC memory cards is different, so pay careful
attention to the logo when purchasing.

■ The SD memory card logo is ( ).

■ The SDHC memory card logo is ( ).

■ The maximum capacity of SD memory cards is 2GB. The maximum

capacity of SDHC memory cards is 16GB.

Card Type Capacities

SD 8MB, 16MB, 32MB, 64MB, 128MB, 256MB,

512MB, 1GB, 2GB

SDHC 4GB, 8GB, 16GB

Inserting an SD/SDHC memory card

To insert an SD/SDHC memory card, follow the steps as detailed below:

1. Insert the SD/SDHC memory card into the SD Card slot on the front of
the computer.

2. Press the SD/SDHC memory card gently to ensure a firm connection is
made.

SD/SDHC

SD Card slot

Figure 3-5 Inserting an SD/SDHC memory card

■ Make sure the SD/SDHC memory card is oriented properly before you

insert it.

■ Make sure that the SD/SDHC memory card is facing the correct

direction when inserting it into the SD Card slot.

■ Do not turn the computer off or switch to Sleep Mode or Hibernation

Mode while files are being copied - doing so may cause data to be lost.

memory card

User’s Manual 3-20

Hardware, Utilities and Options

Removing an SD/SDHC memory card

To remove an SD/SDHC memory card, follow the steps as detailed below:

1. Open the Safely Remove Hardware icon on the Windows Taskbar.

2. Point to SD Memory Card and click the left Touch Pad control button.

3. Press the SD/SDHC memory card to partially extend it out of the
computer.

4. Grasp the SD/SDHC memory card and remove it.

SD Card slot

SD/SDHC memory card

Figure 3-6 Removing an SD/SDHC memory card

■ Make sure the SD Card indicator is out before you remove the

SD/SDHC memory card or turn off the computer’s power. If you remove
the SD/SDHC memory card or turn off the power while the computer is
accessing the SD/SDHC memory card you may lose data or damage
the card.

■ Do not remove an SD/SDHC memory card while the computer is in

Sleep or Hibernation Mode. The computer could become unstable or
data in the SD/SDHC memory card could be lost.

Formatting an SD/SDHC memory card

SD/SDHC memory cards are sold already formatted in conformity to
specific standards. If you format the SD/SDHC memory card again, be sure
to format it with the TOSHIBA SD Memory Card Format utility, not with the
format command provided within Windows.

In order to run the TOSHIBA SD Memory Card Format utility, click Start

-> All Programs -> TOSHIBA -> Utilities -> SD Memory Card Format.

The TOSHIBA SD Memory Card Format utility does not format the
protected area of the SD/SDHC memory card - should you need to format
all areas of the memory card, including the protected area, you will need to
obtain an appropriate application that applies the copy protection system.

User’s Manual 3-21

Hardware, Utilities and Options

Media care

Observe the following precautions when handling the card.

Card care

■ Do not twist or bend cards.

■ Do not expose cards to liquids or store in humid areas or lay media

close to containers of liquid.

■ Do not touch the metal part of a card or expose it to liquids or let it get

dirty.

■ After using card, return it to its case.

■ The card is designed so that it can be inserted only one way. Do not try

to force the card into the slot.

■ Do not leave a card partially inserted in the slot. Press the card until you

hear it click into place.

Memory card care

■ Set the write-protect switch to the lock position, if you do not want to

record data.

■ Memory cards have a limited lifespan, so it is important to backup

important data.

■ Do not write to a card if the battery power is low. Low power could affect

writing accuracy.

■ Do not remove a card while read/write is in progress.

For more details on using memory cards, see manuals accompanying the
cards.

Additional memory module

You can install additional memory into the computer in order to increase the
amount of system memory that is available. This section describes how to
install and remove optional memory modules.

■ You should place a mat beneath the computer in order to prevent the

computer's lid from becoming scratched or damaged when you are
installing/replacing the memory module. In this instance you should
avoid mats that are made of materials that hold or generate static
electricity.

■ When installing or removing a memory module, you must ensure that

you do not touch any other internal areas of the computer.

■ Insert the two memory modules into Slot A and Slot B respectively. The

computer will operate in dual channel mode.
You can access the inserted memory modules efficiently in dual
channel.

User’s Manual 3-22

Hardware, Utilities and Options

■ Use only memory modules approved by TOSHIBA.

■ Do not try to install or remove a memory module under the following

conditions.
a. The computer is turned on.
b. The computer was shut down in either Sleep or Hibernation Mode.
c. Wake-up on LAN is enabled.
d. Wake-up on Wireless LAN is enabled.
e. The wireless communication switch is turned on.

■ Be careful not to let screws or other foreign matter fall into the

computer. It could cause malfunction or electric shock.

■ Additional memory module is a precision electronic component that

may be fatally damaged by static electricity. Since the human body can
carry static electricity, it is important that you discharge yourself before
touching or installing any additional memory modules. To discharge
your body’s static electricity, simply touch any metal close to you with
bare hands.

Point to note about memory module error

If you install a memory module that is not compatible with the computer, the
Power indicator will flashes (on for 0.5 seconds, off for 0.5 seconds) in the
following ways;

■ If there is an error in only Slot A or no memory module is inserted in Slot

A: repeatedly flashes orange twice, then green.

■ If there is an error in Slot B: repeatedly flashes orange, then green

twice.

■ If there are errors in both Slot A and Slot B: repeatedly flashes orange

twice, then green twice.

In all instances you should shut down the computer and remove the
incompatible module(s).

Use a point size 0 Phillips screwdriver to remove and fasten the screws ­the use of an incorrect screwdriver can damage the screw heads.

Installing a memory module

To install a memory module, follow the steps as detailed below:

1. Shut down the computer - make sure the Power indicator is off (refer to
the Turning off the power section in Chapter 1, Getting Started if
required).

2. Remove the AC adaptor and all cables and peripherals connected to
the computer.

3. Close the display panel.

4. Turn the computer upside down and remove the battery pack (refer to

Replacing the battery pack section in Chapter 6, Power and Power-Up

Modes, if required).

User’s Manual 3-23

Hardware, Utilities and Options

5. Loosen the two screws securing the memory module cover in place ­please note that this screw is attached to the cover in order to prevent it
from being lost.

Use a point size 0 Phillips screwdriver.

6. Slide your fingernail or a thin object under the cover and lift it off.

Screws

Memory
module cover

Figure 3-7 Removing the memory module cover

7. Align the notch of the memory module with that of the memory slot and
gently insert the module into the slot at about a 45 degree angle before
holding it down until the latches on either side snap into place.

Slot A

Slot B

Figure 3-8 Seating the memory module

Notch

■ Never allow metal objects, such as screws, staples and paper clips, to

enter the computer. Foreign metal objects can create a short circuit,
which can cause computer damage and fire, possibly resulting in
serious injury.

■ Do not touch the connectors on the memory module or on the

computer. Debris on the connectors may cause memory access
problems.

User’s Manual 3-24

Hardware, Utilities and Options

■ The slot A is reserved for the first memory module. Use the slot B for

expanded memory. If only one module is installed, use the slot A.

■ Align the grooves along the edges of the memory module with the

latches on the connector and insert the module into the connector
firmly - if you find it difficult to install the memory module, gently prise
the locking tabs outwards using the tip of your finger.

Please also ensure that you hold the memory module along its left and
right hand edges - the edges with the grooves in.

8. Seat the memory module cover in place and secure it with two screws.

Take care to ensure that the memory module cover is firmly closed.

Screws

Memory
module cover

Figure 3-9 Seating the memory module cover

9. Install the battery pack - refer to Replacing the battery pack section in
Chapter 6, Power and Power-Up Modes, if required.

10. Turn your computer over.

11. Turn the computer on and make sure the added memory is recognized ­to confirm it, Start -> Control Panel -> System and Security

-> System icon.

Removing a memory module

To remove the memory module, follow the steps as detailed below:

1. Shut down the computer - make sure the Power indicator is off (refer to
the Turning off the power section in Chapter 1, Getting Started if
required).

2. Remove the AC adaptor and all cables and peripherals connected to
the computer.

3. Close the display panel.

4. Turn the computer upside down and remove the battery pack (refer to

Replacing the battery pack section in Chapter 6, Power and Power-Up

Modes, if required).

5. Loosen the two screws securing the memory module cover in place ­please note that this screw is attached to the cover in order to prevent it
from being lost.

User’s Manual 3-25

Hardware, Utilities and Options

6. Slide your fingernail or a thin object under the cover and lift it off.

7. Push the latches away from the module in order to release it - a spring
will force one end of the module up at an angle.

8. Grasp the module by its edges and remove it from the computer.

■ If you use the computer for a long time, the memory modules and the

circuits locating close to the memory modules will become hot. In this
case, let them cool to room temperature before you replace them. Or
you will get burnt if you touch any of them.

■ Do not touch the connectors on the memory module or on the

computer. Debris on the connectors may cause memory access
problems.

Latches

Figure 3-10 Removing the memory module

9. Seat the memory module cover in place and secure it with two screws.

Take care to ensure that the memory module cover is firmly closed.

10. Install the battery pack - refer to Replacing the battery pack section in
Chapter 6, Power and Power-Up Modes, if required.

11. Turn your computer over.

User’s Manual 3-26

Hardware, Utilities and Options

External monitor

An external analog monitor can be connected to the external monitor port
on the computer. To connect a monitor, follow the steps as detailed below:

There are no fastening screws for an external monitor cable on this
computer's external monitor port. However, external monitor cables which
have connectors with fastening screws can still be used.

Connecting the monitor cable

1. Turn the computer's power off.

2. Connect the monitor cable to the external monitor port.

Monitor cable

External monitor port

Figure 3-11 Connecting the monitor cable to the external monitor port

3. Turn the external monitor's power on.

4. Turn the computer's power on.

When you turn on the power, the computer will automatically recognize the
monitor and determine whether it is a color or monochrome device. In the
event that you find that there are issues getting an image displayed on the
correct monitor, you should consider using the FN + F5 hot key to change
the display settings (if you then disconnect the external monitor before you
turn the computer's power off, be sure to press FN + F5 hot key again to
switch to the internal display).

Please refer to Chapter 5, The Keyboard, for further details on using hot
keys to change the display setting.

Do not disconnect the external monitor while in Sleep or Hibernation Mode.
Turn off the computer before disconnecting the external monitor.

User’s Manual 3-27

Hardware, Utilities and Options

USB FDD Kit

The USB floppy diskette drive accommodates either a 1.44MB or 720KB
floppy diskette and connects to one of the computer's USB ports.

USB connector

Disk-In-Use
Indicator

Floppy
diskette slot

Eject button

Figure 3-12 The USB floppy diskette drive

Connecting the USB floppy diskette drive

To connect the drive, plug the floppy diskette drive’s USB connector into a
computer’s USB port.

Make sure the connector is properly aligned with the socket. Do not try to
force the connection, doing so can damage the connecting pins.

USB port

USB connector

Figure 3-13 Connecting the USB floppy diskette drive

User’s Manual 3-28

Hardware, Utilities and Options

If you connect the USB floppy diskette drive after the computer has already
been turned on, it will take about ten seconds for it to be recognized by the
computer. Do not attempt to disconnect and reconnect the drive before this
period has elapsed.

Disconnecting the USB floppy diskette drive

When you have finished using the USB floppy diskette drive, you can follow
the procedures below in order to disconnect it:

1. Wait for the Disk-In-Use Indicator light to go out to make sure all floppy
diskette activity has stopped.

If you disconnect the USB floppy diskette drive or turn off the power while
the computer is accessing the drive you may lose data or damage the
floppy diskette or the drive.

2. Click the Safely Remove Hardware icon on the Windows Taskbar.

3. Click the USB floppy diskette drive device that you want to remove.

4. Carefully pull the floppy diskette drive's USB connector out from within
the computer's USB port.

eSATA (External Serial ATA)

An device corresponding to eSATA function can be connected to the
eSATA/USB combo port on the computer.

Connecting the eSATA device

To connect an eSATA device, follow the steps as detailed below:

1. Connect an eSATA cable to the eSATA/USB combo port.

Make sure the connector is properly aligned with the socket.
Do not try to force the connection, doing so can damage the connecting

pins.

eSATA/USB

eSATA cable

Figure 3-14 Connecting an eSATA cable to the eSATA/USB combo port

User’s Manual 3-29

combo port

Hardware, Utilities and Options

■ A connected eSATA device may not be recognized if it is connected to

the computer's eSATA/USB combo port while the computer is in Sleep
Mode or Hibernation Mode. If this occurs, disconnect the eSATA device
and then reconnect the device while the computer is turned on.

■ If you connect an eSATA device after the computer has already been

turned on, it will take about ten seconds for it to be recognized by the
computer.
Do not attempt to disconnect and reconnect the drive before this period
has elapsed.

Disconnecting an eSATA device

When you have finished using an eSATA device, you can follow the
procedures below in order to disconnect it:

1. Wait for the indicator light of an eSATA device to go out to make sure all
activity has stopped.

If you disconnect an eSATA device or turn off the power while the
computer is accessing the drive you may lose data or damage an eSATA
device or the drive.

2. Click the Safely Remove Hardware icon on the Windows Taskbar.

3. Click an eSATA device that you want to remove.

4. Carefully pull an eSATA device's eSATA/USB combo connector out
from within the computer's eSATA/USB combo port.

TOSHIBA Express Port Replicator

In addition to the ports available on the computer, the TOSHIBA Express
Port Replicator provides a DVI port. The TOSHIBA Express Port Replicator
connects directly to the docking interface on the underside of the computer.
The AC adaptor connects the TOSHIBA Express Port Replicator to a power
source.

The computer must be configured properly before connecting to a LAN.
Logging onto a LAN using the computer’s default settings could cause a
malfunction in LAN operation. Check with your LAN administrator
regarding set-up procedures

■ You must connect the AC adaptor before you connect to a TOSHIBA

Express Port Replicator.

■ When a TOSHIBA Express Port Replicator is connected to the

computer, you can not use the following computer’s ports: LAN jack,
DC IN 15V jack and External monitor port.

■ When connecting an AC Adaptor to the TOSHIBA Express Port

Replicator, use only the AC Adaptor included with TOSHIBA Express
Port Replicator. Do not use the computer’s AC Adaptor.

User’s Manual 3-30

.

Hardware, Utilities and Options

The following ports are available on the TOSHIBA Express Port Replicator.

■ RJ45 LAN jack

■ External monitor port

■ DC IN 15V jack

■ Security lock slot

■ Universal Serial Bus 2.0 port (four)

■ DVI port

■ As the port operation of all DVI (Digital Visual Interface) monitors has

not been confirmed, some DVI monitors may not function properly.

■ Set the TOSHIBA Express Port Replicator's Slide Adjuster to SLIDE

position #4 when connecting this computer to the TOSHIBA Express
Port Replicator. Refer to the TOSHIBA Express Port Replicator User's
Manual for more details on connection methods.

Security lock

A security locks enable you to anchor your computer a desk or other heavy
object in order to help prevent unauthorized removal or theft. The computer
has a security lock slot on its left side into which you can attach one end of
the security cable, while the other end attaches to a desk or similar object.
The methods used for attaching security cables differ from product to
product. Please refer to the instructions for the product you are using for
more information.

Connecting the security lock

In order to connect a security cable to the computer, follow the steps as
detailed below:

1. Turn the computer so its left hand side faces you.

2. Align the security cable with the 'lock hole' and secure it in place.

Security lock slot

Figure 3-15 Security lock

User’s Manual 3-31

Optional accessories

You are able to add a number of options and accessories in order to make
your computer even more powerful and convenient to use. For reference,
the following list details some of the items that are available from your
reseller or TOSHIBA dealer:

Hardware, Utilities and Options

DDR2-800 Memory
Kit

Universal AC
Adaptor

Battery Pack An additional battery pack can be purchased for

Slice Expansion
Battery

Slice Expansion
Battery adaptor

Battery Charger The optional battery charger allows you to

USB FDD Kit The USB floppy diskette drive accommodates

TOSHIBA Express
Port Replicator

Privacy Filter By attaching the Privacy Filter to computer you

A 1,024MB or 2,048MB memory module (DDR2-

800) can easily be installed in the computer.

If you frequently use your computer at more than
one site, it may be convenient to purchase an
additional AC adaptor to be kept at each site in
order to remove the need to always carry the
adaptor with you.

use as either a spare or replacement. Please
refer to Chapter 6, Power and Power-Up Modes
for further information.

This battery pack increases your computer's
operating time when a main battery pack is also
installed. It is connectable to the Docking port of
the computer.

The Slice Expansion Battery adaptor is used to
connect with the Battery Charger in order to
charge a Slice Expansion Battery.

charge extra battery packs outside of having to
use the computer.

either a 1.44MB or 720KB floppy diskette through
connection to one of the computer's USB ports.
In use, please be aware that, while you cannot
format 720KB floppy diskettes under Windows 7,
you are able to read and write to diskettes that
have already been formatted.

The TOSHIBA Express Port Replicator provides
the ports available on the computer in addition to
a digital visual interface (DVI) port, External
monitor port, four Universal Serial Bus ports
(USB 2.0) and a LAN jack.

can prevent people from "peeking" at your
screen from the left or right of you.

User’s Manual 3-32

Operating Basics

This chapter describes the basic operations of your computer, highlights
the precautions that should be taken when using it.

Using the Touch Pad

To use the Touch Pad, simply touch and move your fingertip across it in the
direction you want the on-screen pointer to go.

Chapter 4

Fingerprint Sensor

Touch Pad
control buttons

Touch Pad

Figure 4-1 Touch Pad and Touch Pad control buttons

The two buttons below the Touch Pad are used like the buttons on a
standard mouse - press the left button to select a menu item or to
manipulate text or graphics designated by the pointer, and press the right
button to display a menu or other function depending on the software you
are using.

User’s Manual 4-1

You can also tap the Touch Pad to perform functions similar to those of the
left button on a standard mouse.

Click: Tap on ce
Double-click: Tap twice
Drag and drop: Tap to select the item(s) you want to move, leave your

finger on the Touch Pad after the second tap and then move the item(s)
to their new destination.

Using the Fingerprint Sensor

This product has a fingerprint utility installed for the purpose of enrolling
and recognizing fingerprints. By enrolling the ID and password onto the
fingerprint authentication feature, it is no longer necessary to input the
password from the keyboard. Fingerprint feature enables you to:

■ Logon to Windows and access a security enabled homepage through

Internet Explorer.

■ Files and folders can be encrypted/decrypted and third party access to

them prevented.

■ Disable the password-protected screen-saver when returning from a

power-saving mode such as Sleep Mode.

■ Authentication of the User Password (and, if applicable, the HDD(Hard

Disk Drive) Password) when booting up the computer (Boot
Authentication).

■ Single Sign On feature

Operating Basics

Fingerprint cannot be used in models that do not have a fingerprint module
installed.

How to Swipe your Finger

Using the following steps when swiping fingers for fingerprint registration or
authentication will help to minimize authentication failures:

Align the first joint of the finger to the center of the sensor. Lightly touch the
sensor and swipe finger levelly towards you until the sensor surface
becomes visible. In performing this process, you should also take care to
ensure that the center of your fingerprint is on the sensor.

User’s Manual 4-2

Operating Basics

The following illustrations show the recommended way to swipe your finger
over the fingerprint sensor.

Sensor

Sensor

Figure 4-2 Swipe the finger

■ Avoid swiping with your finger stiff or pressed too hard onto the sensor,

and take care to ensure that the center of the fingerprint is touching the
sensor before swiping. Either of these conditions may cause fingerprint
reading to fail.

■ Check the center of the fingerprint whorl before swiping and then

ensure this is swiped along the center line of the sensor.

■ There is a possibility of authentication failures if the finger is swiped too

quickly or too slowly - follow any on-screen instructions to adjust the
speed used during the swipe process.

Points to note about the Fingerprint Sensor

Please be aware of the following considerations when using the fingerprint
sensor. A failure to follow these guidelines might result in damage to the
sensor, sensor failure, fingerprint recognition problems or a lower
fingerprint recognition success rate.

■ Do not scratch or poke the sensor with your nails or any hard or sharp

objects.

■ Do not press the sensor strongly.

■ Do not touch the sensor with a wet finger or any wet objects - keep the

sensor surface dry and free from water vapor.

■ Do not touch the sensor with a soiled or dirty finger as minute foreign

particles of dust and dirt may scratch it.

■ Do not paste stickers or write on the sensor.

■ Do not touch the sensor with a finger or any other object which may

have a build-up of static electricity on it.

User’s Manual 4-3

Operating Basics

Observe the following before you place your finger on the sensor whether
for fingerprint enrollment/registration or recognition.

■ Wash and dry your hands thoroughly.

■ Remove static electricity from your fingers by touching any metal

surface. Static electricity is a common cause of sensor failures,
especially when the weather is dry.

■ Clean the sensor with a lint-free cloth - do not use detergent or any

other chemicals to clean the sensor.

■ Avoid the following finger conditions for enrollment or recognition as

they may result in fingerprint enrollment errors or a drop in the
fingerprint recognition success rate

■ Soaked or swollen finger, for example as may occur after taking a

bath.

■ Injured finger

■ Wet finger

■ Soiled or oily finger

■ Extremely dry skin condition on finger

Observe the following to improve the fingerprint recognition success rate.

■ Enroll two or more fingers.

■ Enroll additional fingers if a recognition failure often occurs when using

already enrolled fingers.

■ Check the condition of your finger - any conditions which have changed

since enrollment, such as injury, rough skin, and extremely dry, wet,
soiled, dirty, oily, soaked or swollen fingers, may lower the recognition
success rate. Also if the fingerprint is worn down or the finger becomes
thinner or fatter, the recognition success rate may be lowered.

■ As the fingerprint for each finger is different and unique you should

ensure that only the registered or enrolled fingerprint or fingerprints are
used for identification.

■ Check the position and speed at which you swipe your finger across the

sensor - please refer to the preceding drawing.

■ The fingerprint sensor compares and analyzes the unique

characteristics in a fingerprint. However, there may be instances where
certain users are unable to register their fingerprints due to insufficient
unique characteristics in their fingerprints.

■ The recognition success rate may differ from user to user.

Points to note about the Fingerprint utility

■ If Windows 7 file encryption function EFS (Encryption File System) is

used to encrypt a file, the file cannot be further encrypted using the
encryption function of this software.

■ You can back up the fingerprint data or the information registered to

Automatic password input in IE.

■ You can use Import/Export on TOSHIBA Fingperprint Utility main menu.

User’s Manual 4-4

■ Please also refer to the fingerprint utility Help file for more information.

You can start it using the following method:

■ Click Start -> All Programs -> TOSHIBA -> Utilities -> TOSHIBA

Fingerprint Utility. The main screen is displayed. Click ? in the

lower left corner of the screen.

Fingerprint utility limitations

TOSHIBA does not guarantee that the fingerprint utility technology will be
completely secure or error-free, or that it will accurately screen out
unauthorized users at all times. TOSHIBA is not liable for any failure or
damage that might arise out of the use of the fingerprint software.

■ The fingerprint sensor compares and analyzes the unique

characteristics in a fingerprint. However, there may be instances where
certain users are unable to register their fingerprints due to insufficient
unique characteristics in their fingerprints.

■ The recognition success rate may differ from user to user.

Setup Fingerprint Registration

Please use the following procedure when first using fingerprint
authentication.

■ The fingerprint authentication uses the same Windows logon ID and

password. If the Windows logon password has not been setup, please
do so before registration.

■ This sensor has the memory space for at least 20 fingerprint patterns.

You might be able to register more fingerprint patterns depending on
the sensor memory usage.

Operating Basics

1. Click Start -> All Programs -> TOSHIBA -> Utilities -> TOSHIBA
Fingerprint Utility, or click the utility icon in the Task Bar.

2. The Enroll screen is displayed. Enter the current account password
into the Windows Password field. If no Windows password had been
configured, you will be asked to configure the new logon password.
then click Next.

3. Click the non-enrolled finger icon above the finger you want to register
and then click Next.

4. The note for enrollment operation screen is displayed. Confirm the
message and then click Next.

5. The scanning practice screen is displayed. You are able to practice
swiping (three times) your finger to ensure you use the correct method.
When you have finished practicing swiping your finger, click Next.

6. Swipe three times with the same finger. If scanning of fingerprint
succeeds, "Enrollment succeed! Do you want to save this
fingerprint?" message box will appear, click OK.

7. The following message will be displayed: "It is Strongly
recommended you enroll one more fingerprint." Click OK
and repeat steps 3, 4, 5 and 6 with another finger.

User’s Manual 4-5

■ It is strongly recommended that you register 2 or more fingerprints.

■ You cannot enroll the same fingerprint more than once, even on a

different user account.

Delete the Fingerprint Data

Saved fingerprint data is stored in special non-volatile memory inside the
fingerprint sensor. Therefore, if you give the computer to someone else, or
dispose of it in any way, the following process is recommended to delete
your fingerprint information:

Delete the fingerprint data for the currently logged in user.

1. Click Start -> All Programs -> TOSHIBA -> Utilities -> TOSHIBA
Fingerprint Utility, or click the utility icon in the Task Bar.

2. Swipe your finger across the fingerprint sensor.

3. The TOSHIBA Fingerprint Utility main menu is displayed. Select
Enroll in the main menu.

4. In the Enroll window, it enable you to delete the fingerprint data for the
currently logged in user. Click an enrolled finger you want to delete,
"Are you sure you want to delete this fingerprint
template?" message box will appear on the screen, click OK.
If you want to delete the other fingerprints, repeat this step.
If only one fingerprint is registered, the message "Sorry! At least
one fingerprint is required." will appear after clicking OK.
You are not allowed to delete a unique fingerprint.

5. Click Close.

6. "Are you sure you want to quit" is displayed. Click OK. It will
be returned to the TOSHIBA Fingerprint Utility main menu.

Operating Basics

Delete all users fingerprints

1. In the TOSHIBA Fingerprint Utility main menu, click Run as
administrator in the lower left.

2. User Account Control window is displayed. Click Yes.

3. Swipe your enrolled finger.

4. Select Fingerprint Control option.

5. A list of fingerprint information for all the users is shown in the screen.
Click Delete All in the lower right.

6. "Are you sure you want to delete all fingerprints?"
message box will appear on the screen, click OK.

7. Click Close.

8. "Are you sure you want to quit" is displayed. Click OK. It will
be returned to the TOSHIBA Fingerprint Utility main menu.

User’s Manual 4-6

Operating Basics

Windows Logon via Fingerprint Authentication

In place of the usual Windows logon by ID and password, fingerprint
authentication also allows logon to Windows.

This is useful especially when many users are using the computer, as user
selection can be skipped.

Fingerprint Authentication Procedure

1. Start up the computer.

2. The Logon Authorization screen is displayed. Choose any of the
enrolled fingers and swipe the fingerprint on the sensor. If
authentication is successful, the user will be logged on to Windows.

■ If the fingerprint authentication fails, please logon using the Windows

logon password.

■ Please logon using the Windows logon password if the fingerprint

authentication failed for five times. To logon using the Windows logon
password, enter the Windows logon password at the [Welcome] screen
as normal.

■ A warning message will be displayed when authentication is abnormal

or authentication is not successful within a fixed duration.

Fingerprint Boot Authentication and Single Sign-on feature

overview about fingerprint boot authentication

The fingerprint authentication system can be used to replace the keyboard
based User Password authentication system when booting up.

If you do not want to use the fingerprint authentication system for password
authentication when booting up, but prefer to use the keyboard-based
system instead, click the user's tile when the Fingerprint System
Authentication screen is displayed. This will switch the password input
screen to the keyboard-based one.

■ It is necessary to register the User Password before using the

fingerprint boot authentication feature and its extended function, the
fingerprint Single sign-on feature. Please use TOSHIBA HW Setup to
register the User Password.

■ If you fail fingerprint authentication more than five times, you must

enter the User Password or Supervisor Password manually to start the
computer.

■ When swiping, please do it slowly and at a constant speed. If this does

not improve the authentication rate, please adjust the speed.

■ If there are any changes in the environment or settings related to

authorization, you will be required to provide authorization information
such as a User Password and HDD password.

User’s Manual 4-7

Operating Basics

Overview about Fingerprint Single Sign-on feautre

This is a feature that allows the user to complete the authentication for both
the User/BIOS Password (and, if applicable, the HDD (Hard Disk Drive)
Password) and logging onto Windows using only one fingerprint
authentication when booting up.

It is necessary to register the User/BIOS Password and Windows Logon
Password before using the fingerprint boot authentication and this
fingerprint Single sign-on feature. Please use the TOSHIBA Password
Utility to register your User/BIOS Password. If Windows Logon is not the
default for your system, see Manual to register your Windows Logon
Password.

Only one fingerprint authentication is required to replace the User/BIOS
Password (and, if applicable, the HDD(Hard Disk Drive) Password) and the
Windows Logon Password.

How to Enable Fingerprint Boot Authentication and Single
Sign-On Feature

It is necessary to first enroll your fingerprint with the TOSHIBA Fingerprint
Utility prior to enabling and configuring the boot authentication and Single
Sign-On feature. You should check that your fingerprint is enrolled before
configuring the settings.

1. Logon as Administrator (means a user has administrator privileges).

2. Click Start -> All Programs -> TOSHIBA -> Utilities -> TOSHIBA
Fingerprint Utility.

3. Swipe your finger across the fingerprint sensor.

4. The TOSHIBA Fingerprint Utility main menu is displayed. Click Run
As Administrator in lower left.

5. User Account Control window is displayed. Click Yes.

6. Swipe your finger across the fingerprint sensor.

7. Select Setting in the main menu to open the Setting window, you can

■ Select Boot authentication check box if you want to use the

fingerprint boot authentication feature.

■ Select Boot authentication and Single sign-on check boxes if you

want to use the Single sign-on feature.

8. Click Apply.

9. "Save succeeded" is displayed. Click OK.

10. Click Close.

11. "Are you sure you want to quit" is displayed. Click OK. It will
be returned to the TOSHIBA Fingerprint Utility main menu.

The modified configuration for fingerprint boot authentication and Single
sign-on feature becomes effective the next time the system is booted up.

User’s Manual 4-8

Web Camera

Web Camera is a device that allows you to record video or take
photographs with your computer. You can use it for video chatting or video
conferences using a communication tool such as Windows Live
Messenger. TOSHIBA Web Camera Application will help you to add
various video effects to your video or photograph.

Enables the transmission of video and use of video chat via the internet
using specialized applications.

The effective pixel count for this web camera is 0.3 million (maximum
photograph size: 640x480 pixels).

Some models are equipped with a Web Camera.
Please refer to the Web Camera Application Online Help for details.

Operating Basics

Figure 4-3 Web Camera

Web Camera
LED

Web Camera

■ Do not point the web camera directly at the sun.

■ Do not touch or press strongly on the web camera lens. Doing so may

reduce image quality. Use an eyeglass cleaner (cleaner cloth) or other
soft cloth to clean the lens if it becomes dirty.

■ Setting the [Size] to more than "640x480" will cause a larger amount of

data to be written to the hard disk drive and may interfere with smooth
recording.

User’s Manual 4-9

Using the TOSHIBA Face Recognition

TOSHIBA Face Recognition uses a face verification library to verify the
face data of users when they log in to Windows. The user can thus avoid
having to enter a password or the like, which makes the login process
easier.

Some models are equipped with a TOSHIBA Face Recognition.

■ TOSHIBA Face Recognition does not guarantee the correct

identification of a user. Changes to the likeness of a registrant, such as
hair style changes, wearing a cap, or wearing glasses may effect the
recognition rates when such changes occur after the registrant had
registered.

■ TOSHIBA Face Recognition may incorrectly recognize faces that are

similar to a registrant.

■ For high security purposes, TOSHIBA Face Recognition is not a

suitable substitute for Windows passwords. When security is a high
priority, use your established Windows passwords to log in.

■ Bright background light and/or shadows may prevent a registrant from

being recognized correctly. In that case, log in using your Windows
password. If recognition of a registrant fails repeatedly, refer to your
computer documentation to learn ways to improve recognition
performance.

■ TOSHIBA Face Recognition records face data in a log when face

recognition fails. When transferring ownership or disposing of your
computer, please uninstall the application or delete all the logs created
by the application. For details on how to do this, see help file.

■ TOSHIBA Face Recognition can be used only in Windows 7.

Operating Basics

Disclaimer

Toshiba does not guarantee that the face recognition utility technology will
be completely secure or error-free. Toshiba does not guarantee that the
face recognition utility will accurately screen out unauthorized users at all
times. Toshiba is not liable for any failure or damage that might arise out of
the use of the face recognition software or utility.

TOSHIBA, ITS AFFILIATES AND SUPPLIERS SHALL HAVE NO
RESPONSIBILITY FOR DAMAGE TO OR LOSS OF ANY BUSINESS,
PROFITS, PROGRAMS, DATA, NETWORK SYSTEMS OR REMOVABLE
STORAGE MEDIA ARISING OUT OF OR RESULTING FROM THE USE
OF THE PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY
THEREOF.

User’s Manual 4-10

How to register the Face Recognition Data

Take a picture for facial verification purposes, and register the data needed
when you log in. To register the data needed when you log in, follow the
steps as described below:

1. To launch this utility, click Start -> All Programs -> TOSHIBA ->
Utilities -> Face Recognition.

■ The Registration screen is displayed for a logged-in user whose

face has not been registered.

■ The Management screen is displayed for a logged-in user whose

face has already been registered.

2. Click Run as administrator in lower left of the Management screen,
and then click the Register button. The Registration screen is
displayed.

■ If you wish to practice, click on the Next button in the Registration

screen.

■ If you do not wish to practice, click on the Skip button in the

Registration screen.

3. Click the Next button to start the guide. Follow the guide to practice.

■ Click the Back button to practice the guide once more.

4. Click the Next button to start image-capturing process.
Adjust the position of your face so that it fits within the face-shaped
frame.

5. Once your face has been positioned properly, the recording will
commence.
Start moving your neck very slightly to the left and right, and then move
your neck down and up.

6. Registration will end after you have repeatedly moved your neck left,
right, down and up.
When the register succeeds, below message will be displayed on the
screen:
" Registration successful. Now we’ll do the
verification test. Click the Next button.".
Click the Next button to perform the verification test.

7. Perform the verification test. Face the screen as you do when you
register.

■ If verification fails, click the Back button and re-register. Please refer

to step 6 from step 4.

8. If verification is successful, click the Next button and register an
account.

9. Register the account.
Fill in all the fields.

10. The Management screen is displayed.
The registered account name will be displayed. Clicking on it will cause
the captured image of your face to be displayed on the left.

Operating Basics

User’s Manual 4-11

How to Delete the Face Recognition Data

Delete image data, account information, and personal record data created
during registration. To delete the Face Recognition Data, follow the steps
as described below:

1. To launch this utility, click Start -> All Programs -> TOSHIBA ->
Utilities -> Face Recognition.
The Management screen is displayed.

2. Select a user which is displayed in the Management screen.

3. Click the Delete button. "You are about to delete the user
data. Would you like to continue?" will be displayed on the
screen.

■ If you do not want the data to be deleted, click the No button and

you will then be returned to the Management screen.

■ Clicking on the Yes button will remove the selected user from the

Management screen.

How to launch the help file

For further information on this utility, please refer to help file.

1. To launch the help file, click Start -> All Programs -> TOSHIBA ->

Utilities -> Face Recognition Help.

Windows Logon via TOSHIBA Face Recognition

This section explains how to login to Windows with TOSHIBA Face
Recognition. Two authentication modes are provided.

■ AUTO Mode Login screen : If the face authentication tile is selected by

default, you can log in without using the keyboard or mouse.

■ 1:1 Mode Login screen : This mode is essentially the same as AUTO

mode, but the Select Account screen will appear before the Display
Captured Image screen, and you will need to select the user account
to be authenticated in order to start the authentication process.

Operating Basics

AUTO Mode Login screen

1. Turn on the computer.

2. The Select Tiles screen will be displayed.

3. Select Start face recognition ().

4. "Please face the camera" will be displayed.

5. Verification will be performed. If the authentication is successful, the
image data taken in step 4 will be faded in and placed over one another.

■ If an error occurs during authentication, you will be returned to the

Select Tiles screen.

6. The Windows Welcome screen will be displayed, and will be logged in
automatically to Windows.

User’s Manual 4-12

1:1 Mode Login screen

1. Turn on the computer.

2. The Select Tiles screen will be displayed.

3. Select Start face recognition ().

4. The Select Account screen will be displayed.

5. Select the account, and click the arrow button.

6. "Please face the camera" will be displayed.

7. Verification will be performed. If the authentication is successful, the
image data taken in step 6 will be faded in and placed over one another.

■ If an error occurs during authentication, you will be returned to the

Select Tiles screen.

8. The Windows Welcome screen will be displayed, and will be logged in
automatically to Windows.

■ If authentication was successful, but an authentication error

subsequently occurred during the login to Windows, you will be
asked to provide your account information.

Using optical disc drives

The full-size drive provides high-performance execution of CD/DVD-ROM­based programs. You can run either 12 cm (4.72") or 8 cm (3.15")
CD/DVDs without an adaptor. A Serial ATA interface controller is used for
CD/DVD-ROM operation. When the computer is accessing a CD/DVD­ROM, an indicator on the drive glows.

Operating Basics

Use the DVD playback application to view DVD-Video discs.

If you have a DVD Super Multi drive, refer also to the Writing CD/DVDs on

DVD Super Multi drives section for precautions on writing to CDs/DVDs.

When the power of the optical disc drive is off, pressing the FN + Tab keys
will turn the power of the optical disc drive on. Furthermore, it is possible to
set it to turn the power of the optical disc drive on and eject the tray at the
same time.

User’s Manual 4-13

Loading discs

To load CD/DVDs, follow the steps as detailed below:

1. When the computer’s power is on, press the eject button to open
the disc tray slightly.

2. Grasp the disc tray gently and pull until it is fully opened.

Disc tray

Figure 4-4 Pressing the eject button and pulling the disc tray open

3. Lay the CD/DVD, label side up, in the disc tray.

Operating Basics

Eject button

Laser lens

Figure 4-5 Inserting a CD/DVD

When the disc tray is fully opened, the edge of the computer will extend
slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD
at an angle when you place it in the disc tray. After seating the CD/DVD,
however, make sure it lies flat.

User’s Manual 4-14

Operating Basics

■ Do not touch the laser lens or any portion of its surrounding casing as

this could cause misalignment.

■ Prevent foreign objects from entering the drive. Check the surface of

the disc tray, especially the area behind the front edge of the disc tray,
to make sure there are no such objects before closing the drive.

4. Press gently at the center of the CD/DVD until you feel it click into
place. The CD/DVD should lie below the top of the spindle, flush with
the spindle base.

5. Push the center of the disc tray to close it. Press gently until it locks into
place.

If the CD/DVD is not seated properly when the disc tray is closed, the
CD/DVD might be damaged. Also, the disc tray might not open fully when
you press the eject button.

Figure 4-6 Closing the CD/DVD disc tray

Removing discs

To remove the CD/DVD, follow the steps as detailed below:

Do not press the eject button while the computer is accessing the media
drive. Wait for the optical disc drive indicator to go out before you open the
disc tray. Also, if the CD/DVD is spinning when you open the disc tray, wait
for it to stop before you remove it

1. To pop the disc tray partially open, press the eject button. Gently pull
the disc tray out until it is fully opened.

When the disc tray pops open slightly, wait a moment to make sure the
CD/DVD has stopped spinning before pulling the disc tray fully open.

User’s Manual 4-15

.

2. The CD/DVD extends slightly over the sides of the disc tray so you can
grasp it. Gently lift out the CD/DVD.

Figure 4-7 Removing a CD/DVD

3. Push the center of the disc tray to close it. Press gently until it locks into
place.

How to remove CD/DVD when the disc tray will not open

Pressing the eject button will not open the disc tray when the computer
power is off. If the power is off, you can open the disc tray by inserting a
slender object (about 15 mm) such as a straightened paper clip into the
eject hole near the eject button.

Operating Basics

Eject hole

Figure 4-8 Manual release with the eject hole

Turn off the power before you use the eject hole. If the CD/DVD is spinning
when you open the disc tray, the CD/DVD could fly off the spindle and
cause injury.

User’s Manual 4-16

Writing CD/DVDs on DVD Super Multi drives

You can use the DVD Super Multi drive to write data to either CD-R, CD­RW, DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R (Double
Layer), DVD+RW or DVD-RAM discs. The TOSHIBA Disc Creator is
provided as writing software with this computer.

■ Please refer to the Writable discs, Chapter 2 for details about the types

of writable CD and DVD discs that can be supported by this computer.

■ Do not turn off the power to the optical disc drive while the computer is

accessing it as this may cause you to lose data.

■ To write data to CD-R/-RW media, use the TOSHIBA Disc Creator

feature that is installed on your computer.

■ When the power of the optical disc drive is off, the disc tray will not

open even if the eject button is pushed. Use the ODD to turn the power
of the optical disc drive on. Please refer to Chapter 5, Hot keys.

When writing information to media using an optical drive, you should
always ensure that you connect the AC adaptor to a live power socket. It is
possible that, if data is written while powered by the battery pack, the write
process may sometimes fail due to low battery power - in these instances
data loss may occur.

Important message

Before you write or rewrite to any of the media supported by the DVD
Super Multi Drive, please read and follow all of the setup and operating
instructions in this section. If you fail to do so, you may find that the DVD
Super Multi drive may not function properly, and you may fail to write or
rewrite information successfully - this may cause you to either lose data or
incur other damage to the drive or media.

Operating Basics

Disclaimer

TOSHIBA does not bear responsibility for the following:

■ Damage to any CD-R, CD-RW, DVD-R, DVD-R (Dual Layer), DVD-RW,

DVD+R, DVD+R (Double Layer), DVD+RW or DVD-RAM disc that may
be caused by writing or rewriting with this product.

■ Any change or loss of the recorded contents of CD-R, CD-RW, DVD-R,

DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R (Double Layer),
DVD+RW or DVD-RAM media that may be caused by writing or
rewriting with this product, or for any business profit loss or business
interruption that may be caused by the change or loss of the recorded
contents.

■ Damage that may be caused by using third party equipment or

software.

User’s Manual 4-17

Given the technological limitations of current optical disc writing drives, you
may experience unexpected writing or rewriting errors due to disc quality or
problems with hardware devices. In view of this, it is good practice to make
two or more copies of important data, in case of any undesired change or
loss of the recorded contents.

Before writing or rewriting

■ Based on TOSHIBA's limited compatibility testing, we suggest the

following manufacturers of CD-R, CD-RW, DVD-R, DVD-R (Dual
Layer), DVD-RW, DVD+R, DVD+R (Double Layer), DVD+RW or DVD­RAM media, however, it must be noted that disc quality can affect write
or rewrite success rates. Please also be aware that in no event does
TOSHIBA guarantee the operation, quality or performance of any disc.

CD-R:

TAIYO YUDEN CO., Ltd.
MITSUBISHI KAGAKU MEDIA CO., LTD.
Ricoh Co., Ltd.
Hitachi Maxell,Ltd.

CD-RW: (Multi-Speed and High-Speed)

MITSUBISHI KAGAKU MEDIA CO., LTD.
Ricoh Co., Ltd.

CD-RW: (Ultra-Speed)

MITSUBISHI KAGAKU MEDIA CO., LTD.

Operating Basics

DVD-R:

DVD Specifications for Recordable Disc for General Version 2.0

TAIYO YUDEN Co.,Ltd. (for 8x and 16x speed media)
MITSUBISHI KAGAKU MEDIA CO., LTD. (for 4x, 8x and 16x speed
media)
Hitachi Maxell,Ltd. (for 8x and 16x speed media)

DVD-R (Dual Layer):

MITSUBISHI KAGAKU MEDIA CO., LTD. (for 4x and 8x speed media)

DVD+R:

MITSUBISHI KAGAKU MEDIA CO., LTD. (for 8x and 16x speed
media)
Ricoh Co., Ltd. (for 8x and 16x speed media)
TAIYO YUDEN CO., Ltd. (for 8x and 16x speed media)

DVD+R (Double Layer):

MITSUBISHI KAGAKU MEDIA CO., LTD. (for 2.4x and 8x speed
media)

User’s Manual 4-18