Toshiba Tecra M3 Series, M3-S212TD, M3-S311, M3-S336, M3-S636 User Manual

...

Download

Tecra® M3 Series User’s Guide

If you need assistance:

❖ Toshiba’s Support Website

pcsupport.toshiba.com

❖ Toshiba Global Support Centre

Calling within the United States (800) 457-7777 Calling from outside the United States (949) 859-4273

For more information, see “If Something Goes Wrong” on

page 207 in this guide.

PMAD00028012 08/05

Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling.

Model: Tecra M3 Series

Recordable and/or ReWritable Drive(s) and Associated Software Warranty

The computer system you purchased may include Recordable and/or ReWritable optical media drive(s) and associated software, among the most advanced data storage technologies available. As with any new technology, you must read and follow all set-up and usage instructions in the applicable user guides and/or manuals enclosed or provided electronically. If you fail to do so, this product may not function properly and you may lose data or suffer other damage. TOSHIBA AMERICA INFORMATION SYSTEMS, INC. (“TOSHIBA”), ITS AFFILIATES AND SUPPLIERS DO NOT WARRANT THAT OPERATION OF THE PRODUCT WILL BE UNINTERRUPTED OR ERROR FREE. YOU AGREE THAT TOSHIBA, ITS AFFILIATES AND SUPPLIERS SHALL HAVE NO RESPONSIBILITY FOR DAMAGE TO OR LOSS OF ANY BUSINESS, PROFITS, PROGRAMS, DATA, NETWORK SYSTEMS OR REMOVABLE STORAGE MEDIA ARISING OUT OF OR RESULTING FROM THE USE OF THE PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY THEREOF.

Protection of Stored Data

For your important data, please make periodic back-up copies of all the data stored on the hard disk or other storage devices as a precaution against possible failures, alteration, or loss of the data. IF YOUR DATA IS ALTERED OR

LOST DUE TO ANY TROUBLE, FAILURE OR MALFUNCTION OF THE HARD DISK DRIVE OR OTHER STORAGE DEVICES AND THE DATA CANNOT BE RECOVERED, TOSHIBA SHALL NOT BE LIABLE FOR ANY DAMAGE OR LOSS OF DATA, OR ANY OTHER DAMAGE RESULTING THEREFROM. WHEN COPYING OR TRANSFERRING YOUR DATA, PLEASE BE SURE TO CONFIRM WHETHER THE DATA HAS BEEN SUCCESSFULLY COPIED OR TRANSFERRED. TOSHIBA DISCLAIMS ANY LIABILITY FOR THE FAILURE TO COPY OR TRANSFER THE DATA CORRECTLY.

Critical Applications

The computer you have purchased is not designed for any “critical applications.” “Critical applications” means life support systems, medical applications, connections to implanted medical devices, commercial transportation, nuclear facilities or systems or any other applications where product failure could lead to injury to persons or loss of life or catastrophic property damage.

ACCORDINGLY, TOSHIBA, ITS AFFILIATES AND SUPPLIERS DISCLAIM ANY AND ALL LIABILITY ARISING OUT OF THE USE OF THE COMPUTER PRODUCTS IN ANY CRITICAL APPLICATIONS. IF YOU USE THE COMPUTER PRODUCTS IN A CRITICAL APPLICATION, YOU, AND NOT TOSHIBA, ASSUME FULL RESPONSIBILITY FOR SUCH USE.

FCC Notice “Declaration of Conformity Information”

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

❖ Reorient or relocate the receiving antenna.

❖ Increase the separation between the equipment and receiver.

❖ Connect the equipment to an outlet on a circuit different from that to which

the receiver is connected.

❖ Consult the dealer or an experienced radio/TV technician for help.

NOTE

Only Peripherals complying with the FCC Class B limits may be attached to this equipment. Operation with noncompliant peripherals or peripherals not recommended by Toshiba is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer's parallel port, monitor port, USB port, PS/2 port port and microphone jack. Changes or modifications made to this equipment not expressly approved by Toshiba or parties authorized by Toshiba could void the user's authority to operate the equipment.

, i.LINK®

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

❖ This device may not cause harmful interference.

❖ This device must accept any interference received, including interference

that may cause undesired operation.

Contact either:

❖ Toshiba’s Support Website at pcsupport.toshiba.com.

❖ Or call the Toshiba Global Support Centre:

Within the United States at (800) 457-7777 Outside the United States at (949) 859-4273

Industry Canada requirement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conformé à la norme NMB-003 du Canada.

FCC requirements

The following information is pursuant to FCC CFR 47, Part 68 and refers to internal modems.

This equipment complies with Part 68 of the FCC rules. On the bottom of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment. If requested, the information must be provided to the telephone company.

The modem connects to the telephone line by means of a standard jack called the USOC RJ11C.

A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC part 68 rules and requirements adopted by the ACTA. It is designed to be connected to a compatible modular jack that is also compliant.

The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by the ## are the REN without a

decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.

Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information.

Telephone Company Procedures

The goal of the telephone company is to provide you with the best service it can. In order to do this, it may occasionally be necessary for them to make changes in their equipment, operations or procedures. If these changes might affect your service or the operation of your equipment, the telephone company will give you notice, in writing, to allow you to make any changes necessary to maintain uninterrupted service.

If Problems Arise

If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advanced notice is not practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.

If trouble is experienced with this equipment, for repair or limited warranty information, please contact Toshiba Corporation, Toshiba America Information Systems, Inc. or an authorized representative of Toshiba, or the Toshiba Support Centre within the United States at (800) 457-7777 or Outside the United States at (949) 859-4273. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.

Disconnection

If you should ever decide to permanently disconnect your modem from its present line, please call the telephone company and let them know of this change.

Fax Branding

The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device, including Fax machines, to send any message unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business or other entity, or other individual sending the message and the telephone number of the sending machine or such business, other entity, or individual. (The telephone number

provided may not be a 900 number or any other number for which charges exceed local or long-distance transmission charges.)

In order to program this information into your fax transmission, refer to the fax software instructions installed on this computer.

Alarm Equipment

If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.

Instructions for IC CS-03 Certified Equipment

1 NOTICE: The Industry Canada label identifies certified equipment.

This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.

Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.

Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.

2 The user manual of analog equipment must contain the equipment’s

Ringer Equivalence Number (REN) and an explanation notice similar to the following:

The Ringer Equivalence Number (REN) of this device can be found on the label affixed to your computer.

NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.

3 The standard connecting arrangement (telephone jack type) for this

equipment is jack type(s): USOC RJ11C.

Wireless Interoperability

The TOSHIBA Wireless LAN Mini PCI Card products are designed to be interoperable with any wireless LAN product that is based on Direct Sequence Spread Spectrum (DSSS) radio technology, and is compliant to:

❖ The IEEE 802.11 Standard on Wireless LANs (Revision A/B/G), as defined

and approved by the Institute of Electrical and Electronics Engineers.

❖ The Wireless Fidelity (Wi-Fi) certification as defined by the Wi-Fi Alliance.

The “Wi-Fi CERTIFIED” logo is a certification mark of the Wi-Fi Alliance.

Bluetooth® and Wireless LAN devices operate within the same radio

frequency range and may interfere with one another. If you use Bluetooth and Wireless LAN devices simultaneously, you may occasionally experience a less than optimal network performance or even lose your network connection.

If you should experience any such problem, immediately turn off your Bluetooth or Wireless LAN device.

Please contact Toshiba PC product support on Web site http://www.toshibaeurope.com/computers/tnt/bluetooth.htm in Europe or pcsupport.toshiba.com in the United States for more information.

This device is restricted to indoor use due to its operation in the 5.15 GHz to

5.25 GHz frequency range.

Wireless LAN and your Health

Wireless LAN products, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitted by Wireless LAN devices however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones.

Because Wireless LAN products operate within the guidelines found in radio frequency safety standards and recommendations, TOSHIBA believes Wireless LAN is safe for use by consumers. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.

In some situations or environments, the use of Wireless LAN may be restricted by the proprietor of the building or responsible representatives of the organization. These situations may for example include:

❖ Using the Wireless LAN equipment on board airplanes, or

❖ In any other environment where the risk of interference to other devices or

services is perceived or identified as harmful.

If you are uncertain of the policy that applies on the use of wireless devices in a specific organization or environment (e.g. airports), you are encouraged to ask for authorization to use the Wireless LAN device prior to turning on the equipment.

Regulatory Information

The TOSHIBA Wireless LAN Mini PCI Card must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product. This device complies with the following radio frequency and safety standards.

Canada – Industry Canada (IC)

This device complies with RSS 210 of Industry Canada.

The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada’s Web site www.hc-sc.gc.ca/rpb. The RF device shall not be co-located with any other transmitter that has not been tested with this device.

Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device.

L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes: (1) il ne doit pas produire de brouillage et (2) l’utilisateur du dispositif doit étre prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.

The term “IC” before the equipment certification number only signifies that the Industry Canada technical specifications were met.

To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.

Pour empecher que cet appareil cause du brouillage au service faisant l'objet d'une licence, il doit etre utilize a l'interieur et devrait etre place loin des fenetres afin de Fournier un ecram de blindage maximal. Si le matriel (ou son antenne d'emission) est installe a l'exterieur, il doit faire l'objet d'une licence.

This device is restricted to indoor use due to its operation in the 5.15 GHz to

5.25 GHz frequency range. Industry Canada requires this product to be used indoors for frequency range 5.15 GHz to 5.25 GHz to reduce the potential for harmful interference to co-channel Mobile Satellite systems.

High power radars are allocated as primary users of the 5.25 GHz to 5.35 GHz and 5.65 GHz to 5.85 GHz bands. These radar stations can cause interference with and/or damage this device.

Europe – EU Declaration of Conformity

❖ This device complies with the essential requirements of the R&TTE

Directive 1999/5/EC with essential test suites as per standards:

EN 60950 Safety of Information Technology equipment.

ETS 300 328 Technical requirements for radio equipment.

ETS 300 826 General EMC requirements for radio equipment.

English: Hereby, TOSHIBA Corp. Digital Media Network Company, declares

that this Radio LAN device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

Finnish: Valmistaja TOSHIBA Corp. Digital Media Network Company

vakuuttaa täten että Radio LAN device tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.

Dutch: Hierbij verklaart TOSHIBA Corp. Digital Media Network Company dat

het toestel Radio LAN device in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.

Bij deze TOSHIBA Corp. Digital Media Network Company dat deze Radio LAN device voldoet aan de essentiële eisen en aan de overige relevante bepalingen van Richtlijn 1999/5/EC.

French: Par la présente TOSHIBA Corp. Digital Media Network Company

déclare que l'appareil Radio LAN device est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/ CE.

Par la présente, TOSHIBA Corp. Digital Media Network Company déclare que ce Radio LAN device est conforme aux exigences essentielles et aux autres dispositions de la directive 1999/5/CE qui lui sont applicables.

Swedish: Härmed intygar TOSHIBA Corp. Digital Media Network Company att

denna Radio LAN device står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.

Danish: Undertegnede TOSHIBA Corp. Digital Media Network Company

erklærer herved, at følgende udstyr Radio LAN device overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF

German: Hiermit erklärt TOSHIBA Corp. Digital Media Network Company, dass

sich dieser/diese/dieses Radio LAN device in Übereinstimmung mit den grundlegenden Anforderungen und den anderen relevanten Vorschriften der Richtlinie 1999/5/EG befindet. (BMWi)

Hiermit erklärt TOSHIBA Corp. Digital Media Network Company die Übereinstimmung des Gerätes Radio LAN device mit den grundlegenden Anforderungen und den anderen relevanten Festlegungen der Richtlinie 1999/5/EG. (Wien)

Greek:

Italian: Con la presente TOSHIBA Corp. Digital Media Network Company

dichiara che questo Radio LAN device è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.

Spanish: Por medio de la presente TOSHIBA Corp. Digital Media Network

Company declara que el Radio LAN device cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.

Portuguese: TOSHIBA Corp. Digital Media Network Company declara que este

Radio LAN device está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE.

USA – Federal Communications Commission (FCC)

This device complies with Part 15 of FCC Rules. Operation of the devices in a Wireless LAN System is subject to the following two conditions:

❖ This device may not cause harmful interference. ❖ This device must accept any interference that may cause undesired

operation.

TOSHIBA is not responsible for any radio or television interference caused by unauthorized modification of the devices included with this TOSHIBA Wireless LAN Mini PCI Card, or the substitution or attachment of connecting cables and equipment other than specified by TOSHIBA.

The correction of interference caused by such unauthorized modification, substitution or attachment will be the responsibility of the user.

Exposure to Radio Frequency Radiation

The radiated output power of the TOSHIBA Wireless LAN Mini PCI Card is far below the FCC radio frequency exposure limits. Nevertheless, the TOSHIBA Wireless LAN Mini PCI Card shall be used in such a manner that the potential for human contact during normal operation is minimized. In normal operating configuration, the LCD in the upright position, the distance between the antenna and the user should not be less than 20 cm. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Antenna(s) used in 5.15 GHz to 5.25 GHz frequency band must be integral antenna which provide no access to the end user.

Refer to the Regulatory Statements as identified in the documentation that comes with those products for additional information.

Radio Frequency Interference Requirements

This device is restricted to indoor use due to its operation in the 5.15 GHz to

5.25 GHz frequency range. FCC requires this product to be used indoors for frequency range 5.15 GHz to 5.25 GHz to reduce the potential for harmful interference to co-channel Mobile Satellite systems.

High power radars are allocated as primary users of the 5.25 GHz to 5.35 GHz and 5.65 GHz to 5.85 GHz bands. These radar stations can cause interference with and/or damage this device.

NOTE

The above Caution information applies to products that operate with an

802.11a device.

Taiwa n

Article 14 Unless approved, for any model accredited low power radio frequency

electric machinery, any company, trader or user shall not change the frequency, increase the power or change the features and functions of the original design.

Article 17 Any use of low power radio frequency electric machinery shall not affect

aviation safety and interfere with legal communications. In the event interference is caused, the use of such electric machinery shall be immediately discontinued. Operation of such products can be resumed only when they are modified and can no longer cause interference.

The legal communications mentioned in the above item refer to radio communications operated in accordance with telecommunication laws and regulations.

Low power radio frequency electric machinery shall resist against interference from legal communications or from industrial, scientific and medical radio emission electric machinery.

Using this Equipment in Japan

In Japan, the frequency bandwidth of 2,400 MHz to 2,483.5 MHz for second generation low-power data communication systems such as this equipment overlaps that of mobile object identification systems (premises radio station and specified low-power radio station).

1. Sticker

Please put the following sticker on devices incorporating this product.

2. Indication The indication shown below appears on this equipment.

(3)

(1) (2)

2.4DSOF4

1 2.4: This equipment uses a frequency of 2.4 GHz. 2 DS: This equipment uses DS-SS modulation.

OF: This equipment uses OFDM modulation.

3 The interference range of this equipment is less than 40m. 4 This equipment uses a frequency bandwidth from

2,400 MHz to 2,483.5 MHz. It is possible to avoid the band of mobile object identification systems.

3. TOSHIBA Direct PC

Monday – Friday: 10:00 – 17:00

Toll Free Tel: 0120-13-1100

Direct Dial: 03-3457-5916

Fax: 03-5444-9450

(4)

Device Authorization

This device obtains the Technical Regulation Conformity Certification and the Technical Conditions Compliance Approval, and it belongs to the device class of radio equipment of low-power data communication system radio station stipulated in the Radio Law and the Telecommunications Business Law of Japan.

The Name of the radio equipment: refer to the equipment label provided on the computer

JAPAN APPROVALS INSTITUTE FOR TELECOMMUNICATIONS EQUIPMENT

Approval Number: D01-1128JP

TELECOM ENGINEERING CENTER Approval Number: 03NY.A0018, 03GZDA0017

The following restrictions apply:

❖ Do not disassemble or modify the device. ❖ Do not install the embedded wireless module into other device. ❖ 5.17 GHz to 5.23 GHz for indoor use only.

Radio approvals for wireless devices

NOTE

The following information is dependent on what type of wireless device is in your computer.

Approved Countries/Regions for use for the Atheros AR5BMB-43/44 Mini PCI Wireless network adapter

This equipment is approved to the radio standard by the countries/regions in the following table.

Do not use this equipment except in the countries/regions in the following table.

NOTE

802.11b (2.4 GHz)

Australia Austria Belgium Canada Denmark Finland France Germany Greece Ireland Italy Liechtenstein

This device works on passive scan only.

A peer-to-peer mode is not available in 802.11a and Turbo Mode.

Luxembourg Netherlands New Zealand Norway Portugal Sweden Switzerland UK USA

Europe - Restrictions for use of 2.4 GHz Frequencies in European Community Countries

België/ Belgique:

Deutschland: License required for outdoor installations. Check with reseller for

France: Restricted frequency band: only channels 1 to 7 (2400 MHz and 2454

Italia: License required for indoor use. Use with outdoor installations not

Nederland: License required for outdoor installations. Check with reseller for

For private usage outside buildings across public grounds over less than 300m no special registration with IBPT/BIPT is required. Registration to IBPT/BIPT is required for private usage outside buildings across public grounds over more than 300m. For registration and license please contact IBPT/BIPT.

Voor privé-gebruik buiten gebouw over publieke groud over afstand kleiner dan 300m geen registratie bij BIPT/IBPT nodig; voor gebruik over afstand groter dan 300m is wel registratie bij BIPT/IBPT nodig. Voor registratie of licentie kunt u contact opnemen met BIPT.

Dans le cas d’une utilisation privée, à l’extérieur d’un bâtiment, audessus d’un espace public, aucun enregistrement n’est nécessaire pour une distance de moins de 300m. Pour une distance supérieure à 300m un enregistrement auprès de I’IBPT est requise. Pour les enregistrements et licences, veuillez contacter I’IBPT.

procedure to follow. Anmeldung im Outdoor-Bereich notwendig, aber nicht

genehmigungspflichtig.Bitte mit Händler die Vorgehensweise abstimmen.

MHz respectively) may be used outdoors in France. Please contact A.R.T. (http://www.art-telecom.fr) for applicable procedures to follow.

Bande de fréquence restreinte: seuls les canaux 1- 7 (2400 et 2454 MHz respectivement) doivent être utilisés endroits extérieur en France. Vous pouvez contacter I’Autorité de Régulation des Télécommuniations (http://www.art-telecom.fr) pour la procédure à suivre.

allowed. E’necessaria la concessione ministeriale anche per l’uso interno.

Verificare con i rivenditori la procedura da seguire.

procedure to follow.

Licentie verplicht voor gebruik met buitenantennes. Neem contact op met verkoper voor juiste procedure.

802.11a (5 GHz)

Australia Austria Belgium Canada Denmark Finland France Germany Greece Ireland Italy Liechtenstein Luxembourg Netherlands New Zealand Norway Portugal Sweden Switzerland UK USA

Turbo Mode (5 GHz)

Canada USA

Europe - Restrictions for use of 5 GHz Frequencies in European Community Countries

European Community Countries

Austria O x x Belgium, France,

Switzerland/Lichtenstein Denmark, Finland,

Germany, Greece, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Sweden, UK

Iceland, Spain O O O

O: allowed ×: forbidden

5150-5250 MHz

Channels: 36, 40, 44, 48

Indoor Only

OOx

OOO

5250-5350 MHz

Channels: 52, 56, 60, 64

Indoor Only

❖ To remain in conformance with European spectrum usage laws for Wireless

LAN operation, the above 2.4 GHz and 5 GHz channel limitations apply. The user should use the wireless LAN utility to check the current channel of operation. If operation is occurring outside of the allowable frequencies as

5470-5725 MHz

Channels: 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140

Indoor/Outdoor

listed above, the user must cease operating the Wireless LAN at that location and consult the local technical support staff responsible for the wireless network.

❖ The 5 GHz Turbo mode feature is not allowed for operation in any

European Community country.

❖ This device must not be operated in ad-hoc mode using channels in the

5 GHz bands in the European Community. Ad-hoc mode provides a direct communication between two client devices without a Wireless LAN Access Point.

❖ This device must be used with Access Points that have employed and

activated a radar detection feature required for European Community operation in the 5 GHz bands. This device will operate under the control of the Access Point in order to avoid operating on a channel occupied by any radar system in the area. The presence of nearby radar operation may result in temporary interruption of operation of this device. The Access Point’s radar detection feature will automatically restart operation on a channel free of radar. You may consult with the local technical support staff responsible for the wireless network to ensure the Access Point device(s) are properly configured for European Community operation.

Approved Countries/Regions for use for the Atheros AR5001X Mini PCI Wireless network adapter

This equipment is approved to the radio standard by the countries/regions in the following table.

NOTE

Do not use this equipment except in the countries/regions in the following table.

This device works on passive scan only.

A peer-to-peer mode is not available in 802.11a and Turbo Mode.

802.11b (2.4 GHz)

Australia Austria Belgium Canada Denmark Finland France Germany Greece Ireland Italy Liechtenstein Luxembourg Netherlands New Zealand Norway Portugal Sweden Switzerland UK USA

802.11a (5 GHz)

Australia Austria Belgium Canada Denmark Finland France Germany Greece Ireland Italy Liechtenstein Luxembourg Netherlands New Zealand Norway Portugal Sweden Switzerland UK USA

Turbo Mode (5 GHz)

Canada USA

Approved Countries/Regions for use for the Intel® PRO/ Wireless LAN 2100 3B Mini PCI Adapter

This equipment is approved to the radio standard by the countries/regions in the following table.

Do not use this equipment except in the countries/regions in the following table.

Argentina Australia Austria Belgium Brazil Canada Chile Denmark Finland France Germany Greece Iceland Ireland Italy Japan Liechtenstein Luxembourg

Mexico Netherlands New Zealand Norway Peru Portugal Singapore Spain Sweden Switzerland UK Uruguay USA Venezuela

Approved Countries/Regions for use for the Toshiba Mini PCI Wireless LAN Card

This equipment is approved to the radio standard by the countries/regions in the following table.

Do not use this equipment except in the countries/regions in the following table.

Australia Austria Belgium Canada Denmark Finland France Germany Greece Hong Kong Iceland Ireland Italy Japan Liechtenstein Luxembourg Malaysia Netherlands New Zealand Norway Philippines Portugal Singapore Spain Sweden Switzerland Thailand UK USA

Approved Countries/Regions for use for the INPROCOMM IPN2220 Wireless network adapter

This equipment is approved to the radio standard by the countries/regions in the following table.

Do not use this equipment except in the countries/regions in the following table.

EU Canada Japan USA Australia New Zealand

Bluetooth® wireless technology Interoperability

Bluetooth® Cards from TOSHIBA are designed to be interoperable with any

product with Bluetooth wireless technology that is based on Frequency Hopping Spread Spectrum (FHSS) radio technology, and is compliant to:

❖ Bluetooth Specification as defined and approved by The Bluetooth Special

Interest Group.

❖ Logo certification with Bluetooth wireless technology as defined by The

Bluetooth Special Interest Group.

Bluetooth wireless technology is a new innovative technology, and TOSHIBA has not confirmed compatibility of its Bluetooth products with all PCs and/or equipment using Bluetooth wireless technology other than TOSHIBA portable computers.

Always use Bluetooth cards from TOSHIBA in order to enable wireless networks over two or more (up to a total of seven) TOSHIBA portable computers using these cards. Please contact TOSHIBA PC product support on Web site http://www.toshiba-europe.com/computers/tnt/bluetooth.htm in Europe or pcsupport.toshiba.com in the United States for more information.

When you use Bluetooth cards from TOSHIBA close to 2.4 GHz Wireless LAN devices, Bluetooth transmissions might slow down or cause errors. If you detect certain interference while you use Bluetooth cards from TOSHIBA, always change the frequency, move your PC to the area outside of the interference range of 2.4 GHz Wireless LAN devices (40 meters/43.74 yards or more) or stop transmitting from your PC. Please contact TOSHIBA PC product support on Web site http://www.toshiba-europe.com/computers/tnt/ bluetooth.htm in Europe or pcsupport.toshiba.com in the United States for more information.

Bluetooth and Wireless LAN devices operate within the same radio frequency range and may interfere with one another. If you use Bluetooth and Wireless LAN devices simultaneously, you may occasionally experience a less than optimal network performance or even lose your network connection. If you should experience any such problem, immediately turn off either one of your Bluetooth or Wireless LAN. Please contact Toshiba PC product support on Web site http://www.toshiba-europe.com/computers/tnt/bluetooth.htm in Europe or pcsupport.toshiba.com in the United States for more information.

Bluetooth® wireless technology and your Health

The products with Bluetooth wireless technology, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitted by devices with Bluetooth wireless technology however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones.

Because products with Bluetooth wireless technology operate within the guidelines found in radio frequency safety standards and recommendations, TOSHIBA believes Bluetooth wireless technology is safe for use by consumers. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.

In some situations or environments, the use of Bluetooth wireless technology may be restricted by the proprietor of the building or responsible representatives of the organization. These situations may for example include:

❖ Using the equipment with Bluetooth wireless technology on board

airplanes, or

❖ In any other environment where the risk of interference to other devices or

services is perceived or identified as harmful.

If you are uncertain of the policy that applies on the use of wireless devices in a specific organization or environment (e.g. airports), you are encouraged to ask for authorization to use the device with Bluetooth wireless technology prior to turning on the equipment.

Regulatory statements

This product complies with any mandatory product specification in any country/ region where the product is sold. In addition, the product complies with the following:

European Union (EU) and EFTA

This equipment complies with the R&TTE directive 1999/5/EC and has been provided with the CE mark accordingly.

Canada — Industry Canada (IC)

This device complies with RSS 210 of Industry Canada.

L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes: (1) il ne doit pas produire de brouillage et (2) l’utilisateur du dispositif doit étre prét à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.

The term “IC” before the equipment certification number only signifies that the Industry Canada technical specifications were met.

FCC Interference Statement

This device complies with part15 of the FCC rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and

This device must accept any interference received, including interference that may cause undesired operation.

Note that any changes or modifications to this equipment not expressly approved by the manufacturer may void the authorization to operate this equipment.

Exposure to Radio Frequency Radiation

The radiated output power of the Bluetooth Card from TOSHIBA is far below the FCC radio frequency exposure limits. Nevertheless, the Bluetooth Card from TOSHIBA shall be used in such a manner that the potential for human contact during normal operation is minimized.

In order to comply with FCC radio-frequency radiation exposure guidelines for an uncontrolled environment, the Bluetooth Card from TOSHIBA has to be operated while maintaining a minimum body to antenna distance of 20 cm.

Refer to the Regulatory Statements as identified in the documentation that comes with those products for additional information.

The Bluetooth Card from TOSHIBA is far below the FCC radio frequency exposure limits.

Nevertheless, it is advised to use the Bluetooth Card from TOSHIBA in such a manner that human contact during normal operation is minimized.

NOTE

Changes or modifications made to this equipment not expressly approved by TOSHIBA or parties authorized by TOSHIBA could void the user’s authority to operate the equipment.

Taiwa n

Article 14 Unless approved, for any model accredited low power radio frequency

electric machinery, any company, trader or user shall not change the frequency, increase the power or change the features and functions of the original design.

Article 17 Any use of low power radio frequency electric machinery shall not affect

The legal communications mentioned in the above item refer to radio communications operated in accordance with telecommunication laws and regulations.

Low power radio frequency electric machinery shall resist against interference from legal communications or from industrial, scientific and medical radio emission electric machinery.

Using this equipment in Japan

1. Sticker

Please put the following sticker on devices incorporating this product.

2. Indication

The indication shown below appears on this equipment.

(1) (2)

(3)

2.4FH1

(4)

1 2.4: This equipment uses a frequency of 2.4 GHz. 2 FH: This equipment uses FH-SS modulation. 3 The interference range of this equipment is less than 10m. 4 This equipment uses a frequency bandwidth from 2,400 MHz to

2,483.5 MHz. It is impossible to avoid the band of mobile object identification systems.

3. TOSHIBA Direct PC

Monday – Friday: 10:00 – 17:00

Toll Free Tel: 0120-13-1100

Direct Dial: 03-3457-5916

Fax: 03-5444-9450

Device Authorization

This device obtains the Technical Regulation Conformity Certification, and it belongs to the device class of radio equipment of low-power data communication system radio station stipulated in the Radio Law of Japan.

The Name of the radio equipment: EYXF2CS

TELECOM ENGINEERING CENTER

Approval Number: 01NYDA1305

The following restrictions apply:

❖ Do not disassemble or modify the device.

❖ Do not install the embedded wireless module into other device.

DVD-ROM, multi-function drive safety instructions

The DVD-ROM and multi-function drives employ a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference.

Never attempt to disassemble, adjust or repair a CD/DVD drive, CD-RW drive, Multi-drive or any other optical drive. You could damage the drive. You would also be exposed to laser light or other safety hazards, resulting in serious injury. Always contact an authorized Toshiba service provider, if any repair or adjustment is required.

Location of the required label

(Sample shown below. Location of the label and manufacturing information may vary.)

This appliance contains a laser system and is classified as a CLASS 1 LASER PRODUCT. To use this model properly, read the user’s guide carefully and keep it for your future reference.

This guide is copyrighted by Toshiba America Information Systems, Inc. with all rights reserved. Under the copyright laws, this guide cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed, however, with respect to the use of the information contained herein.

Export Administration Regulation

This document contains technical data that may be controlled under the U.S. Export Administration Regulations, and may be subject to the approval of the U.S. Department of Commerce prior to export. Any export, directly or indirectly, in contravention of the U.S. Export Administration Regulations is prohibited.

Notice

The information contained in this manual, including but not limited to any product specifications, is subject to change without notice.

TOSHIBA CORPORATION AND TOSHIBA AMERICA INFORMATION SYSTEMS, INC. (TOSHIBA) PROVIDES NO WARRANTY WITH REGARD TO THIS MANUAL OR ANY OTHER INFORMATION CONTAINED HEREIN AND HEREBY EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE WITH REGARD TO ANY OF THE FOREGOING. TOSHIBA ASSUMES NO LIABILITY FOR ANY DAMAGES INCURRED DIRECTLY OR INDIRECTLY FROM ANY TECHNICAL OR TYPOGRAPHICAL ERRORS OR OMISSIONS CONTAINED HEREIN OR FOR DISCREPANCIES BETWEEN THE PRODUCT AND THE MANUAL. IN NO EVENT SHALL TOSHIBA BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL, OR EXEMPLARY DAMAGES, WHETHER BASED ON TORT, CONTRACT OR OTHERWISE, ARISING OUT OF OR IN CONNECTION WITH THIS MANUAL OR ANY OTHER INFORMATION CONTAINED HEREIN OR THE USE THEREOF.

Trademarks

Tecra, AccuPoint II, Fn-esse, and Slim SelectBay are registered trademarks, and ConfigFree is a trademark, of Toshiba America Information Systems, Inc. and/or Toshiba Corporation.

MS-DOS, Microsoft, Windows, Windows XP Professional, DirectX, Active Desktop, DirectShow, and Windows Media are registered trademarks of Microsoft Corporation in the United States and/or other countries.

Intel is a registered trademark of Intel Corporation.

Wi-Fi is a registered trademark of the Wi-Fi Alliance.

Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Toshiba is under license. Other trademarks and trade names are those of their respective owners.

TouchPad is a trademark of Synaptics, Inc.

Secure Digital and SD are trademarks of the SD Card Association.

xD-Picture Card is a trademark of Fuji.

ExpressCard is a trademark of PCMCIA.

MultiMediaCard is a trademark of Infineon Technologies AG.

All other brand and product names are trademarks or registered trademarks of their respective companies.

Computer disposal information

This product contains mercury. Disposal of this material may be regulated due to environmental considerations. For disposal, reuse or recycling information, please contact your local government or the Electronic Industries Alliance at

www.eiae.org.

Introduction ............................................................................... 37

This guide ...............................................................38

Safety icons ............................................................39

Other icons used...............................................40

Other documentation ..............................................40

Service options .......................................................41

Chapter 1: Getting Started........................................................ 42

Selecting a place to work ........................................42

Creating a computer-friendly environment........42

Keeping yourself comfortable ...........................43

Precautions.......................................................43

Important information on your computer’s

cooling fan ..................................................46

Setting up your computer .......................................46

Setting up your software...................................47

Registering your computer with Toshiba ................48

Adding external devices ..........................................49

Connecting to a power source ................................50

Using the main battery............................................53

Contents

Using the computer for the first time......................54

Your computer’s features and specifications ....55

Turning on the power........................................56

Turning off the computer ........................................57

Closing the display panel ..................................58

Caring for your computer........................................58

Cleaning the computer......................................58

Moving the computer........................................59

Using a computer lock ......................................59

Chapter 2: Connecting Other External Devices ...................... 61

Using external display devices ................................61

Connecting the display device...........................62

Directing the display output when you

turn on the computer ..................................63

Adjusting the quality of the external display......64

Video limitations ...............................................65

Using an external keyboard.....................................65

Connecting a keyboard .....................................65

Making your external keyboard emulate

the Fn key ...................................................66

Using a mouse........................................................66

Connecting a mouse .........................................66

Connecting a local printer ......................................67

Connecting a USB printer..................................67

Connecting a parallel printer .............................67

Connecting an optional external diskette drive........68

Connecting external speakers or headphones.........69

Connecting an external microphone........................70

Using an expansion device......................................70

Adding memory ......................................................71

Installing memory modules ..............................71

Hard Drive Recovery Utilities ..................................77

Creating Recovery CDs/DVDs ...........................78

Contents

Hard Disk Drive Recovery using the

recovery partition........................................80

Hard Disk Drive Recovery using the

Recovery media ..........................................83

Deleting the Hard Disk Recovery Utility.............86

Installing drivers and applications.....................87

Using Slim SelectBay® modules .............................87

Removing a module from the Slim SelectBay®.88

Inserting a module into the Slim SelectBay®.....89

Inserting and removing hard drives ........................89

Inserting and removing PC Cards ...........................93

Setting up a PC Card for your computer ...........93

Inserting a PC Card...........................................93

Removing a PC Card.........................................94

Hot swapping....................................................95

Inserting an ExpressCard™.....................................96

Removing an ExpressCard™.............................96

Inserting an SD™ card ............................................97

Connecting your modem to a telephone line...........98

Connecting to a phone line ..............................98

Using the i.LINK® port ..........................................100

Chapter 3: Learning the Basics.............................................. 101

Computing tips .....................................................101

Using the keyboard ...............................................103

Character keys ...............................................103

Making your keyboard emulate a full-size

keyboard ...................................................103

Ctrl, Fn, and Alt keys .......................................104

Function keys..................................................104

Windows® special keys...................................105

Overlay keys ...................................................105

Using the Toshiba Dual Pointing Device ...............107

Using the TouchPad™.....................................108

Contents

Disabling or enabling the Dual

Pointing Device.........................................109

Using the Toshiba Assist button ...........................110

Starting a program................................................111

Starting a program from Windows® Explorer .112 Starting a program from the Run dialog box ..113

Saving your work..................................................114

File names.......................................................116

Using a file extension......................................116

Printing your work ................................................116

Using the DVD-ROM or multi-function drive.........117

DVD-ROM or multi-function drive

components..............................................118

Inserting a compact disc ................................119

Removing a compact disc with the

computer on .............................................122

Removing a compact disc with the

computer turned off..................................123

Caring for CDs and DVDs................................123

Using your computer at the office.........................124

Powering down the computer...............................124

Using Turn Off or Shut down ..........................125

Using Hibernation ...........................................127

Using Standby ................................................130

Toshiba’s online resources ...................................132

Chapter 4: Mobile Computing................................................ 133

Toshiba’s energy-saver design..............................133

Running the computer on battery power ..............133

Battery Notice .................................................134

Power management ........................................135

Using additional batteries ...............................135

Charging batteries.................................................136

Charging the main battery...............................136

Contents

Charging the RTC battery................................137

Monitoring battery power .....................................139

Determining remaining battery power.............140

What to do when the main battery runs low ...142

Setting battery alarms.....................................142

Conserving battery power ..............................143

Power Profiles ................................................143

Using a hot key to set the Power Profile .........145

Changing the main battery ....................................146

Removing the battery from the computer .......146

Inserting a charged battery .............................148

Taking care of your battery ...................................148

Safety precautions ..........................................148

Maximizing battery life....................................149

Disposing of used batteries safely ........................150

Traveling tips ........................................................152

Chapter 5: Exploring Your Computer’s Features.................. 153

Exploring the desktop ...........................................153

Finding your way around the desktop .............154

Exploring audio features .......................................158

Using external speakers or headphones..........158

Recording sounds...........................................159

Exchanging data with another computer...............162

Getting help transferring files..........................162

Setting up for communications.......................162

Connecting the modem to a telephone line .....164

Connecting your computer to a network.........164

Using Wireless LAN Connectivity....................165

An overview of using the Internet .........................167

The Internet ....................................................167

The World Wide Web .....................................167

Internet Service Providers...............................168

Connecting to the Internet .............................168

Contents

Surfing the Internet.........................................169

Internet features..............................................169

Uploading to, and downloading files from,

the Internet ..............................................170

Chapter 6: Toshiba Utilities..................................................... 171

Fn-esse .................................................................172

Starting Fn-esse .............................................172

Using the keyboard or pointing device

to assign keys ...........................................174

Viewing existing key assignments ..................175

Changing or removing existing key

assignments .............................................176

TOSHIBA HW Setup..............................................176

Accessing TOSHIBA HW Setup.......................176

TOSHIBA Power Saver..........................................179

TOSHIBA Mobile Extension...................................180

TOSHIBA Password Utility ....................................182

TOSHIBA Zooming Utility......................................184

TOSHIBA CD/DVD Drive Acoustic Silencer ...........185

TOSHIBA SD™ Memory Boot Utility......................186

PC Diagnostic Tool ...............................................187

TOSHIBA Mic Effect ..............................................188

TOSHIBA Application Installer...............................188

Chapter 7: Keeping Your Files Safe ....................................... 190

Using passwords in Windows ..............................190

Setting user-level passwords ...............................192

Using an instant user-level password .............192

Setting a Windows user password..................193

Using a power-on (user-level) password ..............193

Setting a power-on (user-level) password ......193

Creating a user token on an SD™ memory

card...........................................................195

Contents

Deleting a power on (user-level) password.....195

Deleting a user token on an SD™ memory

card...........................................................196

Using the power-on (user-level) password .....196

Using a supervisor password................................197

Setting a supervisor password........................197

Creating a supervisor token on an SD™

memory card ............................................199

Deleting a supervisor password......................199

Deleting a supervisor token on an optional

SD™ Memory Card ...................................200

Hard disk drive passwords....................................200

Setting a hard disk drive user only

password in System Setup .......................201

Deleting or changing a hard disk drive

user only password in System Setup........202

Setting a hard disk drive master and user

password in System Setup .......................203

Changing the master and user passwords in

System Setup............................................204

Deleting the hard disk drive master and user

passwords in the System Setup................205

Chapter 8: If Something Goes Wrong................................... 207

Problems that are easy to fix ................................207

Problems when you turn on the computer............209

The Windows® operating system is not working ..211

Using Startup options to fix problems ............212

Internet problems ...........................................213

The Windows® XP operating system

can help you .............................................213

Resolving a hardware conflict...............................214

A plan of action...............................................214

Resolving hardware conflicts on your own .....215

Contents

Fixing a problem with Device Manager ...........216

Memory problems ..........................................218

Power and the batteries ..................................219

Keyboard problems.........................................221

Display problems ............................................222

Disk drive problems........................................224

DVD-ROM or multi-function drive problems...227

Sound system problems .................................228

PC Card problems...........................................228

Printer problems.............................................232

Modem problems............................................233

Wireless networking problems .......................234

DVD operating problems.......................................237

Develop good computing habits ...........................240

Data and system configuration backup in

Windows XP .............................................241

If you need further assistance...............................247

Before you contact Toshiba ............................247

Contacting Toshiba .........................................248

Other Toshiba Internet Web sites .........................249

Toshiba’s worldwide offices..................................249

Appendix A: Hot Keys............................................................. 251

Volume Mute ........................................................251

Password security ................................................252

Without a password........................................252

With a password .............................................252

Maintaining security when the battery is

not fully charged .......................................253

Power usage mode ..............................................254

Standby mode.......................................................254

Hibernation mode ................................................255

Display modes ......................................................256

Display brightness ................................................256

Contents

Disabling or enabling wireless devices..................257

Disabling or enabling the TouchPad .....................257

Keyboard hot keys ...............................................257

Zooming applications in/out .................................258

Appendix B: Power Cord/Cable Connectors......................... 259

Appendix C: Using ConfigFree™ with your

Toshiba Computer............................................. 260

Getting Started......................................................261

Starting ConfigFree .........................................261

ConfigFree Utilities................................................263

Connectivity Doctor ........................................263

Search for Wireless Devices ...........................266

Profile Settings ...............................................271

ConfigFree SUMMIT........................................275

Quick Connect.................................................279

Using the Automatic Switch..................................282

Semi-Automatic Switch Feature............................282

Glossary ................................................................................... 284

Index .........................................................................................299

Introduction

Welcome to the world of powerful, portable, multimedia computing. With your Toshiba notebook computer, your work and entertainment can accompany you wherever you go.

You will find your operating system, Microsoft XP Professional, already installed on your computer. Your operating system offers exciting features, multimedia enjoyment, and easy Internet access.

Windows®

NOTE

Certain Microsoft® software product(s) included with this computer may use technological measures for copy protection. IN SUCH EVENT, YOU WILL NOT BE ABLE TO USE THE PRODUCT IF YOU DO NOT FULLY COMPLY WITH THE PRODUCT ACTIVATION PROCEDURES. Product activation procedures and Microsoft's privacy policy will be detailed during initial launch of the product, or upon certain reinstallations of the software product(s) or reconfigurations of the computer, and may be completed by Internet or telephone (toll charges may apply).

Some software may differ from its retail version (if available), and may not include user manuals or all program functionality.

Introduction

This guide

NOTE

This guide

This guide introduces the computer’s features. You can:

❖ Read the entire guide from beginning to end. ❖ Skim through and stop when a topic interests you. ❖ Use the table of contents and the index to find specific

information.

The product specifications and configuration information are designed for a product Series. Your particular model may not have all the features and specifications listed or illustrated. For more detailed information about the features and specifications on your particular model, please visit Toshiba's Web site at

While Toshiba has made every effort at the time of publication to ensure the accuracy of the information provided herein, product specifications, configurations, prices, system/ component/options availability are all subject to change without notice. For the most up-to-date product information about your computer, or to stay current with the various computer software or hardware options, visit Toshiba’s Web site at pcsupport.toshiba.com.

pcsupport.toshiba.com.

Safety icons

This manual contains safety instructions that must be observed to avoid potential hazards that could result in personal injuries, damage to your equipment, or loss of data. These safety cautions have been classified according to the seriousness of the risk, and icons highlight these instructions as follows:

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

Introduction

Safety icons

NOTE

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

Indicates a potentially hazardous situation which, if not avoided, may result in property damage.

Provides important information.

Introduction

Service options

Toshiba offers a full line of optional service programs to complement its limited warranty. Toshiba's standard limited warranty, extended warranty, and service upgrade terms and conditions are available at www.warranty.toshiba.com.

To stay current on the most recent software and hardware options for your computer, and for other product information, be sure to regularly check the Toshiba Web site at

pcsupport.toshiba.com.

If you have a problem or need to contact Toshiba, see “If

Something Goes Wrong” on page 207.

Introduction

Service options

Chapter 1

Getting Started

This chapter provides tips for working comfortably, summarizes how to connect components, and explains what to do the first time you use your notebook computer.

Selecting a place to work

Your computer is portable and designed to be used in a variety of circumstances and locations.

Creating a computer-friendly environment

Place the computer on a flat surface that is large enough for the computer and any other items you are using, such as a printer. Leave enough space around the computer and other equipment to provide adequate ventilation. Otherwise, they may overheat.

To keep your computer in prime operating condition, protect your work area from:

❖ Dust, moisture, and direct sunlight. ❖ Equipment that generates a strong electromagnetic field,

such as stereo speakers (other than speakers that are connected to the computer) or speakerphones.

❖ Rapid changes in temperature or humidity and sources of

temperature change such as air conditioner vents or heaters.

❖ Extreme heat, cold, or humidity. ❖ Liquids and corrosive chemicals.

Keeping yourself comfortable

The Toshiba Instruction Manual for Safety and Comfort, that shipped with your computer, contains helpful information for setting up your work environment and tips for working comfortably throughout the day.

Getting Started

Selecting a place to work

Precautions

Your computer is designed to provide optimum safety and ease of use, and to withstand the rigors of travel. You should observe certain precautions to further reduce the risk of personal injury or damage to the computer.

❖ Avoid prolonged physical contact with the underside or

surface of the computer.

Getting Started

Selecting a place to work

Never allow any liquids to spill into any part of your computer, and never expose the computer to rain, water, seawater or moisture. Exposure to liquid or moisture can cause electric shock or fire, resulting in damage or serious injury. If any of these eventualities should accidentally occur, immediately:

1. Turn off the computer.

2. Disconnect the AC adapter from the power plug socket and computer.

3. Remove the battery pack.

Failure to follow these instructions could result in serious injury or permanent damage to the computer.

Do not turn on the power again, until you have taken the computer to an authorized service center.

If you experience discomfort while operating the computer, stop immediately and rest. Continuous operation for long periods without adequate rest may cause pain in the arms, wrists, hands, neck or other part of the body. If pain persists despite rest, consult your doctor.

PC base and palm rest can become hot! Avoid prolonged contact to prevent heat injury to skin.

Read the enclosed Instruction Manual for Safety and Comfort.

Getting Started

Selecting a place to work

Some PC Cards can become hot with prolonged use. Overheating of a PC Card can result in errors or instability in its operation.

Before you remove a PC Card, always wait for it to cool. You could get burned removing a hot PC Card.

Never place a heavy object on the computer and be careful not to drop a heavy object onto the computer. It could damage the computer or cause system failure.

❖ Never turn off the computer if a drive light indicates a

drive is active. Turning off the computer while it is reading from or writing to

a disk may damage the disk, the drive, or both.

❖ Keep the computer and disks away from objects that

generate strong magnetic fields, such as large stereo speakers.

Information on disks is stored magnetically. Placing a magnet too close to a disk can erase important files.

Handle discs carefully. Avoid touching the surface of the disc. Grasp it by its center hole and edge. If you handle the disc incorrectly, you could damage the disc and possibly lose data.

❖ Scan all new files for viruses.

This precaution is especially important for files you receive via email or download from the Internet. Occasionally, even new programs you buy from a supplier may contain a computer virus. You need a special program to check for viruses. Ask your dealer to help you.

Getting Started

Setting up your computer

Important information on your computer’s cooling fan

Your computer may have a CPU cooling fan that cools the CPU by drawing outside air into the computer. The cooling fan may be located on the bottom of the computer.

To prevent possible overheating of the CPU, make sure the air intake on the cooling fan is not blocked. The fan draws in air by creating a vacuum. If the fan is blocked, it could cause the CPU to run at a lower performance level or cause the computer to shut down. Loose items such as notebook and tissue paper, plastic wrappers, or other similar materials can block the air intake, preventing air from reaching the CPU. Do not use the computer on surfaces with objects that can be drawn in by the cooling fan.

NOTE

The cooling fan location will vary depending on the computer.

Setting up your computer

TECHNICAL NOTE: You must complete all setup steps up to and including “Setting up your software” on page 47 before adding external or internal components to your computer. These components include, but are not limited to, a mouse, keyboard, printer, memory, and PC Cards.

Your computer contains a rechargeable main battery that needs to be charged before you can use it.

To use external power or to charge the battery you must attach the AC adapter. See “Connecting to a power source”

on page 50.

To register your computer online or to sign up for an Internet account, you must either connect the built-in modem to a telephone line or establish a Local Area Network (LAN) connection. See “Connecting your modem to a telephone

line” on page 98.

Setting up your software

Getting Started

Setting up your computer

NOTE

The first time you turn on your computer, the Setup Wizard guides you through steps to set up your software.

1 From the welcome screen click Next to enter the Setup

2 Confirm acceptance of Microsoft’s End User License

3 Select the appropriate option from the Help protect your

4 Enter the computer name and description and click Next

5 Select how your computer will connect to the Internet

The names of windows displayed, and the order in which windows appear, may vary according to your software setup choices.

Wizard.

Agreement and click Next.

computer screen and click Next.

or Skip.

and click Next. The computer will pause for a moment while checking for an

internet connection.

If an Internet connection could not be found, a window will display the message: “An Internet connection could not be chosen.” Click Next to continue.

Getting Started

Registering your computer with Toshiba

NOTE

6 Follow the remaining screen prompts to complete the

If you are connecting your computer to a network, consult your system administrator before you choose your computer name and network settings.

setup process. Once you click the final screen, your computer restarts

automatically.

Registering your computer with Toshiba

Product registration is strongly recommended, and allows Toshiba to send the Customer periodic updates, announcements, and special offers applicable to the product. Product registration can be completed during the initial start up process of your computer. If you opt not to register at that time, you can either double-click the icon on your desktop or go to the Toshiba web site at www.register.toshiba.com. Customer failure to complete Product Registration will not diminish Customer rights under this limited Warranty.

NOTE

To register online, you must be connected to the Internet via your computer’s modem and a voice-grade telephone line, or by a Local Area Network.

Adding external devices

TECHNICAL NOTE: You must complete all setup steps up to

“Setting up your software” on page 47 before adding external

or internal components to your computer. These components include, but are not limited to, a mouse, keyboard, printer, memory, and PC cards.

Your computer comes with a rechargeable battery pack that must be charged before you can use it.

To use external power or to charge the battery, you must attach the AC adapter. See “Connecting to a power source”

on page 50.

To register your computer online, or to sign up for an Internet account, you must connect the built-in modem to a telephone line.

Getting Started

Adding external devices

Before adding any of these devices to the computer, be sure to complete “Setting up your software” on page 47.

After setting up your computer, you may want to:

❖ Add more memory. See “Adding memory” on page 71. ❖ Connect a mouse. See “Connecting a mouse” on page 66. ❖ Connect a full-size keyboard. See “Using an external

keyboard” on page 65.

❖ Connect an external monitor. See “Using external display

devices” on page 61.

❖ Connect a local printer. See “Connecting a local printer”

on page 67.

❖ Install PC Cards. See “Inserting and removing PC Cards”

on page 93.

For more information on installing specific devices, see

“Connecting Other External Devices” on page 61.

Getting Started

Connecting to a power source

Your computer requires power to operate. Use the power cord/ cable and AC adapter to connect the computer to a live electrical outlet, or to charge the computer’s main battery.

Never pull on a power cord/cable to remove a plug from a socket. Always grasp the plug directly. Failure to follow this instruction may damage the cord/cable, and/or result in a fire or electric shock, possibly resulting in serious injury.

When you connect the AC adapter to the computer, always follow the steps in the exact order as described in the User’s Guide. Connecting the power cord/cable to a live electrical outlet should be the last step; otherwise, the adapter DC output plug could hold an electrical charge and cause an electrical shock or minor bodily injury when touched. As a general safety precaution, avoid touching any metal parts.

Always use the Toshiba AC adapter that was provided with your computer, or use Toshiba recommended alternate models to avoid any risk of fire or other damage to the computer. Use of an incompatible AC adapter could cause fire or damage to the computer, possibly resulting in serious injury.

Getting Started

Connecting to a power source

AC adapter cord

AC adapter

Power cord/cable

Sample power cord/cable and AC adapter cord

To connect AC power to the computer:

1 Connect the power cord/cable to the AC adapter.

Sample connecting the power cord/cable to the AC adapter cord

Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling.

2 Plug the AC adapter cord into the DC-IN on the back of

the computer.

Getting Started

Connecting to a power source

Sample connecting the AC adapter cord to the computer

3 Connect the power cord/cable to a live electrical outlet.

Never tamper with the cord/cable or plug; never splice or alter a cord/cable; never bend or twist a cord/cable; never place heavy objects on a cord/cable; never place a cord/cable near a heat source; never run a cord/cable through a pinch point such as a door or window; never use nails, staples or similar objects to fasten or attach cord in place; never attempt to disassemble or repair an AC adapter or a Battery Charger. Doing any of the above may damage the cables, and/or result in a fire or electric shock, possibly resulting in serious injury.

Never attempt to connect or disconnect a power plug with wet hands. Failure to follow this instruction could result in an electric shock, possibly resulting in serious injury.

The computer’s main battery light gives you an indication of the main battery’s current charge:

❖ Glows amber while the main battery is being charged.

(AC adapter connected)

❖ Glows green when the main battery is fully charged.

Getting Started

Using the main battery

❖ Is unlit when the main battery has discharged, the battery

is not charging, or the AC adapter is not plugged into the computer or AC outlet.

❖ Flashes amber when the main battery charge is low and it

is time to recharge the main battery or plug in the AC adapter.

NOTE

If the AC power light flashes amber during charging, either the main battery is malfunctioning, or it is not receiving correct input from the AC power supply.

Disconnect the AC cable and remove the main battery pack. See “Changing the main battery” on page 146 for information on replacing the main battery.

Using the main battery

To charge the main battery, plug the computer into a live wall outlet. Before using the main battery to power the computer you must first charge it.

To charge the main battery, leave the computer plugged into a live wall outlet for several hours with the computer turned off. After that, the main battery will be completely charged and ready to power the computer.

Once the battery is charged for the first time, avoid leaving the computer plugged in and turned off for more than a few hours at a time. Continuing to charge a fully charged battery can damage the battery.

Getting Started

Using the computer for the first time

TECHNICAL NOTE: The RTC battery does not charge while the computer is turned off, even when AC power is attached.

The RTC battery charges when the computer is powered on.

TECHNICAL NOTE: When your computer is using all of the power provided by the AC Adapter to run applications, features, and devices, the recharging of the battery cannot occur. Your computer's Power Saver utility can be used to select a power level setting that reduces the power required for system operation and allows the battery to recharge.

NOTE

Battery life and charge time may vary depending on the applications, power management settings, and features used.

Using the computer for the first time

The computer is now ready for you to turn it on and begin using it.

Opening the display panel

1 Slide the display latch to the right.

2 Lift the display panel.

Sample opening the display panel

Getting Started

Using the computer for the first time

To avoid damaging the display panel, do not force it beyond the point where it moves easily.

Never lift the computer by the display panel.

Small bright dots may appear on your screen display when you turn on your PC. Your display contains an extremely large number of thin-film transistors (TFT) and is manufactured using high-precision technology. Any small bright dots that may appear on your display are an intrinsic characteristic of the TFT manufacturing technology. Over a period of time, and depending on the usage of the computer, the brightness of the screen will deteriorate. This is also an intrinsic characteristic of the screen technology. When the computer is operated on battery power, the screen will dim and you may not be able to increase the brightness of the screen while on battery power.

Your computer’s features and specifications

Certain notebook chassis are designed to accommodate all possible configurations for an entire product Series. Your selected model may not have all the features and specifications corresponding to all of the icons or switches shown on the notebook chassis, unless you have selected all those features.

This information applies to all the features and icons described in this guide.

Below are examples of some of the many possible icons used on your computer:

Sample system icons

Getting Started

Using the computer for the first time

Turning on the power

To turn on the computer:

1 Make sure any external devices (such as the AC adapter, if

you plan to use AC power rather than battery power) are properly connected and ready.

2 Check to ensure that any diskette drives are empty. 3 Press and hold the power button in until the on/off light

on the system indicator panel glows green—about one second.

Sample turning on the power

The preinstalled operating system loads automatically.

When you turn on the computer for the first time, do not turn off the power again until the operating system has loaded completely.

Never turn off the computer while any drive is in use.

Turning off the computer

It is a good idea to turn off your computer when you are not using it for a while.

If you are using the computer for the first time, leave the computer plugged into a power source (even though the computer is off) to fully charge the main battery. With the computer off, it may take up to three hours to recharge the main battery.

When you power down the computer, you have three options to choose from: Turn Off (or Shut down), Hibernate and Standby. Each option has its advantages.

Getting Started

Turning off the computer

❖ Use the Turn Off command if you are using the

Windows Windows connected to a domain server.

❖ Use the Shut down command if you are using the

Windows connected to a domain server.

❖ If you have work in progress and are not connected to a

network, use the Windows commands to save your system settings to memory. The next time you turn on the computer, you automatically return to where you left off.

❖ To leave the computer off for a longer period, you can use

the Windows a domain server or the Shut down when connected to a domain server instead.

XP Home version operating system, or the

XP Professional operating system when not

XP Professional operating system and

Standby or Hibernate

Turn Off command when not connected to

Never turn off the computer while any drive is in use. Doing so may damage the media in use and result in loss of data. For more information, see “Powering down the computer” on

page 124.

Getting Started

Caring for your computer

Closing the display panel

When you are finished, shut the computer down and close the display panel to keep dust and dirt out of the computer.

If you close the computer while it is still on, the following actions occur:

❖ If you have the LCD power-saver feature set, the LCD

panel automatically turns off until you open it again.

❖ If you have the audible warning set, the computer beeps

to notify you that it is still on.

❖ If you have an action feature set, the computer performs

Nothing, Standby, or Hibernate (see “Using Hibernation”

on page 127).

Caring for your computer

This section gives tips on cleaning and moving your computer. For information about taking care of your computer’s main battery, see “Running the computer on

battery power” on page 133.

Cleaning the computer

Keep liquids, including cleaning fluid, out of the computer’s keyboard, speaker, and other openings. Never spray cleaner directly onto the computer. Never use harsh or caustic chemical products to clean the computer.

To keep your computer clean, gently wipe the display panel and exterior case with a lightly dampened cloth.

Moving the computer

Before moving your computer, even across the room, make sure all disk activity has ended (the drive indicator light stops glowing) and all external peripheral cables are disconnected.

Do not pick up the computer by its display panel or by the back (where the ports are located). Doing so could damage the system.

Although your notebook computer is built to withstand reasonable shock and vibration, transport it in a carrying case for long trips. You can purchase a carrying case from your Toshiba dealer, through the accessories information packaged with your system, or visit

Using a computer lock

For your own peace of mind, you may want to secure your computer to a heavy object such as your desk. The easiest way to do this is to purchase an optional computer lock cable.

Getting Started

Caring for your computer

accessories.toshiba.com.

Sample computer lock cable

To secure the computer:

1 Loop the cable through or around some part of a heavy object.

Make sure there is no way for a potential thief to slip the cable off the object.

2 Pass the locking end through the loop. 3 Slide the PC Card lock (located underneath the PC Card

slots) to secure your PC Cards in place.

Getting Started

Caring for your computer

4 Insert the cable’s locking end into the security lock slot

on the computer, then engage the locking mechanism. The computer is now securely locked.

Chapter 2

Connecting Other External Devices

This chapter describes how to connect devices that can increase the capabilities of your computer.

Using external display devices

Your computer comes with a built-in LCD display, but you can also connect three different types of external display devices to one of two available video ports:

❖ A television via the S-video port. ❖ A video display device, such as a video projection unit,

via the S-video port.

❖ An external monitor or projector via the RGB (monitor)

port.

Connect a television, video projector, monitor, or other display device to your computer and then configure your computer for the type of device you are connecting. The following sections describe how to do this in detail. Also, refer to the documentation for your operating system and devices.

Connecting Other External Devices

Using external display devices

Connecting the display device

If you are connecting a television or other video display device to the computer’s S-video port, first refer to the next two subsections.

If you are connecting an SVGA monitor, skip to “Connecting

an external monitor or projector” on page 63.

Selecting video cables

To connect a device to the S-video port, you must purchase an S-video cable. For the best video quality, always use a properly shielded cable.

HINT: Toshiba recommends using a cable no longer than 20 feet (approximately 6 meters).

Using a poor quality cable may result in a dull or fuzzy picture, poor color, ghosting, video noise, or loss of video.

Connecting to the S-video port

NOTE

1 Connect one end of the S-video cable to the external video

2 Connect the other end of the S-video cable to the S-video

3 Turn on the external video device.

Video cables are not included with your computer. To connect a device to the S-video port, you must purchase an S-video cable.

device.

Refer to the documentation provided with the device for the location of its S-video-in port.

port on the back side of the computer.

Connecting Other External Devices

Using external display devices

4 Set the display mode by pressing Fn + F5 or by using the

Display Properties settings. For more information, see below.

Connecting an external monitor or projector

You can easily attach an external monitor or projector to your computer if you need a larger screen. To do this:

1 Connect the monitor’s video cable to the RGB port on the

back of the computer.

2 Connect the device’s power cable to a live electrical

outlet.

3 Turn on the external device. 4 Set the display mode by pressing

Display Properties settings. For more information, see below.

Fn + F5 or by setting the

Directing the display output when you turn on the computer

Once you have connected an external display device, you can choose to use the internal display only, the external device only, or both simultaneously. The quickest way to change the display output settings is to use the display hot key (

1 Press

2 While holding down

Fn and F5 simultaneously.

Fn, press F5 repeatedly until the

setting you want takes effect. This hot key cycles through the settings in the following

order:

❖ Built-in display only

❖ Built-in display and external device simultaneously

❖ External device only

❖ Built-in display and TV (or other external video device)

simultaneously

Fn + F5):

Connecting Other External Devices

Using external display devices

❖ TV (or other external video device) only

3 Release the

TECHNICAL NOTE: You can also change these settings using the Display Properties Box.

Set the option for the video controller by clicking Start, Control Panel and then Display. Choose the Settings tab, click the Advanced button, select Display Device, select the applicable Monitor type, click Apply or OK.

For more information on switching the display output, see

“Display modes” on page 256.

Fn key.

Adjusting the quality of the external display

To obtain the best picture quality from your television (or other video display device), you may need to adjust the video settings. See the video device documentation for additional configuration steps.

TECHNICAL NOTE: To use one of the simultaneous modes, you must set the resolution of the internal display panel to match the resolution of the external display device.The external display device must support a resolution of 800 x 600 or higher.

Video limitations

Keep in mind that the quality of the display is limited to the capabilities of the external video device.

❖ If the external video device, such as an SVGA monitor, is

capable of displaying at a maximum resolution of 640 x 480 and your system is set for a higher resolution, only part of the desktop appears on the screen. You can scroll to view the “lost” area.

❖ Since most televisions and video projectors overscan by

15 to 20 percent, some of the desktop will be outside the viewing area. You can scroll to view the edge of the desktop.

❖ If you use the display hot key (Fn + F5) to change the

display output with the LCD Display Stretch option enabled and the display area (resolution) set to 640 x 480 or 800 x 600, the image on the internal display panel may appear stretched.

Connecting Other External Devices

Using an external keyboard

If you prefer to use a full-size keyboard, you can attach a USB keyboard to a USB port on your computer or a PS2 keyboard to an optional Advanced Port Replicator III. See your Toshiba sales representative for more information.

Connecting a keyboard

To connect a USB keyboard, gently push the keyboard cable into the USB port. To connect a PS2 keyboard, gently push the keyboard cable into the PS2 port of an optional Advanced Port Replicator III.

Connecting Other External Devices

Using a mouse

Making your external keyboard emulate the Fn key

An external keyboard does not have the Fn key provided by the computer’s built-in keyboard. You can use the Emulation option in Toshiba Hardware Setup to assign an external keyboard key combination to emulate the internal keyboard’s

In Toshiba Hardware Setup, you can emulate the Fn key by setting key combinations in the keyboard option of the utility. See “TOSHIBA HW Setup” on page 176 for more information.

Fn key.

Fn Key

NOTE

The Fn emulation key is not supported when using a USB keyboard.

Using a mouse

If you prefer to use a standard mouse, you can attach a USB mouse to a USB port on your computer, or a PS2 or serial mouse to an optional Advanced Port Replicator III. See your Toshiba sales representative for more information.

Connecting a mouse

To connect a USB mouse, gently push the mouse cable into the USB port. To connect a PS2 or serial mouse, gently push the mouse cable into the PS2 or serial port of an optional Advanced Port Replicator III.

Connecting Other External Devices

Connecting a local printer

NOTE

Your printer documentation may require you to install the printer software before physically connecting the printer to your computer. If you do not install the software as instructed by the printer manufacturer, the printer may not function correctly.

Read the documentation that came with your printer. Follow the manufacturer’s instructions when connecting a local printer.

Connecting a USB printer

These instructions assume you have a USB printer. Consult the document that came with your printer to verify the connection type.

To connect the printer:

1 If the computer is on, turn it off.

2 Connect the printer cable to the printer and then connect

the other end to one of the computer’s USB ports.

3 Plug the printer’s power cable into a live electrical outlet. 4 See your printer documentation for additional

configuration steps.

For information about printing, see “Printing your work” on

page 116.

Connecting a parallel printer

These instructions assume you have a parallel printer. To connect the printer:

1 If the computer is on, turn it off.

Connecting Other External Devices

Connecting an optional external diskette drive

2 Connect the printer cable to the printer and to the

computer’s parallel port. Use the printer cable illustration as a connection guide.

To the computer

Identifying the ends of a parallel printer cable

3 Plug the printer’s power cable into a live electrical outlet. 4 See your printer documentation for additional

configuration steps.

For more information on getting your printer to print, see

“Printing your work” on page 116.

To the printer

Connecting an optional external diskette drive

Some operations, such as creating a password service diskette, require a diskette drive designed for use with

3.5-inch diskettes.

Sample optional external USB diskette drive

To connect an optional external USB diskette drive, connect the cable to one of the USB ports.

Connecting Other External Devices

Connecting external speakers or headphones

Sample connecting an optional external USB diskette drive

Connecting external speakers or headphones

Before putting on headphones to listen to an audio CD, turn the volume dial down, and do not set the volume too high when using the headphones. Continuous exposure to loud sound can harm your hearing.

To attach an external stereo output device (headphone or external speakers):

1 Locate the headphone jack on the right side of the computer.

2 Using any necessary adapters, plug the cable from the

external audio device into the headphone jack. The headphone jack requires a 3.5 mm, 16-ohm stereo jack.

When the headphone is inserted, the internal speakers are automatically disabled.

For more information on using headphones or external speakers, see “Using external speakers or headphones” on

page 158.

Connecting Other External Devices

Connecting an external microphone

Your computer comes equipped with an internal microphone, but to record higher quality sounds, you can attach an external microphone:

1 Locate the microphone jack on the right side of the computer.

2 Plug the microphone cord into the microphone jack. 3 Turn on the microphone.

The internal microphone is automatically disabled.

Once the external microphone is connected, the recording process is the same as with the built-in microphone. For more information, see “Recording sounds” on page 159.

Using an expansion device

The expansion port is used to connect your computer to an expansion device. This is an excellent investment if you are using your computer both in and out of the office.

When you return to your desk, you can then connect to your network, print reports from your computer, or use a mouse instead of the Toshiba Dual Pointing Device. Connecting cables for each of these devices every time you return to the office is time-consuming and inconvenient.

With an expansion device, you can leave external devices connected while you are using your computer away from your desk. When you return, you can quickly connect your computer and have immediate access to all the devices.

For more information, see the accessories information package that comes with the device or visit

accessories.toshiba.com.

Adding memory

HINT: To purchase additional memory modules, see the accessories information packaged with your system or visit

accessories.toshiba.com.

Your computer comes with enough memory to run most of today’s popular applications. You may want to increase the computer’s memory if you use complex software or process large amounts of data.

For more information on memory options, check the accessories information that came with your computer, or visit accessories.toshiba.com.

Connecting Other External Devices

Adding memory

NOTE

Before adding external devices or memory, Toshiba recommends setting up your software. See “Setting up your

software” on page 47.

Installing memory modules

Additional memory modules can be installed in your computer. There are two memory expansion slots (primary and secondary) located under your computer’s keyboard. Normally, you will install or replace a memory module in the secondary slot.

If you use the computer for a long time, the memory module will become hot. If this happens, let the module cool to room temperature before you replace it.

Connecting Other External Devices

Adding memory

To avoid damaging the computer’s screws, use a standard Phillips No. 1 screwdriver that is in good condition.

Installing a memory module with the computer’s power on may damage the computer, the module, or both.

Before you install or remove a memory module, turn off the computer using the Start menu. If you install or remove a memory module while the computer is in Standby or Hibernation mode, data will be lost.

NOTE

1 Shut down your computer completely using the Shut down or

2 Unplug and remove any cables connected to the

3 Remove the battery. For information on removing the

Memory module installation requires significant computer disassembly and reassembly. If you are uncomfortable with this, please contact your Toshiba sales representative for a service professional to complete this procedure.

Turn Off command.

See “Turning off the computer” on page 57 for more information.

computer, including the AC adapter.

battery, see “Changing the main battery” on page 146.

Connecting Other External Devices

Adding memory

4 Close the display panel and turn the computer upside

down to locate and remove the retaining screw. Place the screw in a safe place so that you can retrieve it later.

Sample removing the retaining screw

5 Turn the computer over and slide the display latch to the

right and open the display panel.

6 Carefully insert a thin object under the rim of the

keyboard brace and lift out the brace.

The brace is fragile and should not be bent. Pull the brace out by grasping the left and the right sides.

Connecting Other External Devices

Adding memory

Sample removing the keyboard brace

7 Remove the two screws securing the keyboard. Place the

screws in a safe place so that you can retrieve them later.

8 Lift up the back of the keyboard, rotate it toward you and

lay it face down on the palm rest.

Sample rotating the keyboard

9 Remove the retaining screw and the metal brace. Place

the screw in a safe place so that you can retrieve it later.

Connecting Other External Devices

Adding memory

10 Remove the existing memory module from the slot by

pulling the clips away from the memory module. Place the module in antistatic packaging and store it in a safe place.

Sample removing the metal brace

11 Remove the new memory module from its antistatic

packaging.

12 Insert the memory module into the socket.

Sample installing a memory module

13 Hold the memory module by its edges so that the gold

connector bar faces the slot, at a slight angle to the socket.

Connecting Other External Devices

Adding memory

clip

Sample inserting the memory module into the socket

14 Check that the module is lined up with the socket clips.

Sample aligning the module into the socket

15 Gently press down on the memory module connector

until the clips snap into place.

clip

Sample pressing down on the memory module

Do not force the memory module into position. The memory module should be level when secured in place.

Connecting Other External Devices

Hard Drive Recovery Utilities

The clips on either side of the memory module will click to secure the memory module.

16 Replace the metal brace and the screw. 17 Insert the tabs on the front of the keyboard into

corresponding notches on the computer, seat the keyboard, and secure it with the two screws.

18 Seat the keyboard brace and press to secure latches. 19 Install the battery pack. 20 Turn the computer over and restart it.

When you turn on the computer, it automatically recognizes the additional memory.

Hard Drive Recovery Utilities

Your computer has been configured with a hard disk partition to allow you to recover your hard disk drive or reinstall selected applications and software features or utilities.

Back up your data externally before performing any of the tasks in this section.

NOTE

Using the HDD Recovery, you can:

❖ Create Hard Drive Recovery CDs or DVDs using a

❖ Recover your hard disk drive to the factory-set default. ❖ Recover just your C: drive, leaving any other partitions

It is strongly recommended that you create recovery CDs/ DVDs before using your system. For more information on creating Recovery media, see “Creating Recovery CDs/DVDs”

on page 78.

writable drive.

you may have created intact, for example, a D: drive.

Connecting Other External Devices

Hard Drive Recovery Utilities

❖ Recover your hard disk drive to the factory-set default

state without the HDD Recovery partition.

❖ Delete your hard disk drive recovery partition without the

risk of losing your data.

❖ Reinstall drivers and applications which were bundled

with your computer.

Creating Recovery CDs/DVDs

Depending on your system configuration, you may be able to copy the Hard Drive Recovery Utilities to CD or DVD. This gives you the ability to recover your hard disk drive and reclaim additional hard disk space used to store the Hard Drive Recovery Utilities on your computer.

NOTE

To create recovery CDs/DVDs:

1 Double-click the Recovery Disc Creator icon on the Windows

2 Select CD, DVD, or All Files (to create Recovery media

The system prompts you to insert the appropriate number of CDs or DVDs to copy the Hard Drive Recovery Utilities. If your optical disk drive is not writable, contact TOSHIBA Customer Support to obtain the Recovery media for your system.

desktop. You can also launch the application by clicking

Start, All Programs, and then Hard Disk Recovery Utilities.

on both CDs and DVDs).

Connecting Other External Devices

Hard Drive Recovery Utilities

Sample Recovery Disc Creator screen

3 Select the items you want to copy by clicking the

checkbox next to the item’s Name – recovery files, applications (original bundled drivers and applications), or both the recovery files and applications.

4 Click Burn. 5 Insert the first blank CD or DVD into your computer’s

CD/DVD writable drive when prompted.

6 Follow the on-screen prompts to complete the copy

process.

For more information on using the Recovery media you have created with the preceding steps, see “Hard Disk Drive

Recovery using the Recovery media” on page 83.

Connecting Other External Devices

Hard Drive Recovery Utilities

Hard Disk Drive Recovery using the recovery partition

You have the options of recovering your system using the Hard Drive Recovery partition to the factory-set default, or recovering just your C: drive and leaving other partitions (for example, a D: drive) intact, or changing the size of your C: drive and then recovering it.

To recover your hard disk drive using the utilities stored on your computer’s HDD:

1 Make sure the computer is turned off.

2 Press and hold the 0 (zero) key on your keyboard while

powering on the computer. When the computer powers on, the TOSHIBA HDD Recovery Utility screen displays.

Sample TOSHIBA HDD Recovery Utility screen

Recovering the original factory image (recommended)

Recovering a hard disk drive to its factory default setting deletes all partitions on the hard disk drive and your information will be lost. Be sure to save your work on external media before proceeding.

Connecting Other External Devices

Hard Drive Recovery Utilities

1 Press 1 on the keyboard to recover your hard disk drive to its

original factory setting. A confirmation message displays reminding you that all data will be lost during the recovery process. Be sure you have saved your work on external media before proceeding.

2 Click Ye s to begin the recovery. Once complete, a

message displays that the HDD has been recovered.

3 Press any key on the keyboard to restart the computer.

Recovering the C: partition of the HDD without changing the current partition size

Recovering the C: drive to its factory default setting reformats your drive and your information on the recovered drive will be lost. Be sure to save your work on external media before proceeding. If you have created other partitions (for example, a D: drive), those partitions and any information on them will not be affected and will remain intact.

To recover only your C: drive:

1 Press 2 on the keyboard when the TOSHIBA HDD Recovery

Utility screen displays. A confirmation message appears, reminding you that all information on the C: drive will be lost during the recovery process. Be sure you have saved your work on external media work before proceeding.

2 Click Ye s to begin the restoration. Once complete, a

message displays that the HDD has been recovered.

3 Press any key on your keyboard to restart the computer.

Connecting Other External Devices

Hard Drive Recovery Utilities

Recovering the C: partition with a user specified size

Resizing and recovering your C: drive to its factory default setting reformats all partitions on the HDD (for example, if you created a D: drive, it will be deleted during the recovery process) and your information will be lost. Be sure to save your work on external media before proceeding.

To resize and recover your C: drive:

1 Press 3 on the keyboard when the TOSHIBA HDD Recovery

Utility screen displays. A confirmation message appears, reminding you that all partitions will be reformatted and all information will be lost during the recovery process. Be sure you have saved your work on external media before proceeding.

2 Click Ye s to begin the restoration and to specify the size

of the C: drive.

❖ Press the Left/Right Arrow keys to increase/decrease the

C: drive size by 1 GB.

❖ Press the Up/Down Arrow keys to increase/decrease the

C: drive size by 5 GB.

NOTE

3 Click Enter to begin the restoration. Once complete, a

4 Press any key on your keyboard to restart the computer.

The size of the C: drive displays on the progress bar as you make your selections.

message displays that the HDD has been recovered.

Connecting Other External Devices

Hard Drive Recovery Utilities

Hard Disk Drive Recovery using the Recovery media

If you need to recover your computer to its default factory state, you can re-build the system using your Hard Drive Recovery Utilities.

To recover your hard disk drive using the utilities burned to CDs or DVDs (refer to “Creating Recovery CDs/DVDs” on

page 78):

❖ Insert the first recovery CD or DVD into your CD/DVD

drive and power on the computer. When the computer powers on, the TOSHIBA HDD Recovery Utility screen displays.

Sample TOSHIBA HDD Recovery Utility screen

Recovering the original factory image (recommended)

1 Press 1 on the keyboard to recover your hard disk drive to its

original factory setting. A confirmation message displays, reminding you that all data will be lost during the recovery

Connecting Other External Devices

Hard Drive Recovery Utilities

process. Be sure you have saved your work on external media before proceeding.

2 Click Ye s to begin the recovery process. Once complete,

a message displays that the HDD has been recovered.

3 Press any key on the keyboard to restart the computer.

Recovering the C: partition of the HDD only

To recover only your C: drive:

1 Press 2 on the keyboard when the TOSHIBA HDD Recovery

2 Click Ye s to begin the restoration. Once complete, a

message displays that the HDD has been recovered.

3 Press any key on your keyboard to restart the computer.

Connecting Other External Devices

Hard Drive Recovery Utilities

Recovering the entire HDD without the HDD Recovery Area

This option recovers your C: drive without creating the HDD Recovery Utilities partition. This will increase the size of your C: drive.

Recovering your C: drive to its factory default state without the recovery partition reformats all partitions on the HDD (for example, if you created a D: drive, it will be deleted during the recovery process), and your information will be lost. Be sure to save your work on external media before proceeding.

To recover your C: drive without the recovery partition:

1 Press 3 on the keyboard when the TOSHIBA HDD Recovery

Utility screen displays. A confirmation message appears, reminding you that all partitions will be reformatted and all data will be lost during the recovery process. Be sure you have saved your work on external media before proceeding.

2 Click Ye s to begin the restoration. Once complete, a

message displays that the HDD has been recovered.

3 Press any key on your keyboard to restart the computer.

Checking the HDD operating status

After restoring your hard disk drive, you can check its status as follows:

1 Click Start, and then click Control Panel.

2 Double-click the Administrative Tools icon. 3 Double-click the Computer Management icon. 4 Click Disk Management. 5 Highlight the hard disk drive in the Volume list to display

its status in the lower portion of the screen.

Connecting Other External Devices

Hard Drive Recovery Utilities

Deleting the Hard Disk Recovery Utility

You can delete the HDD recovery partition without losing your data.

1 Click Start, All Programs, Hard Disk Recovery Utilities,

and then Delete Hard Disk Recovery Partition. The Delete Hard Disk Recovery Utility warning screen displays.

Sample Delete Hard Disk Recovery Utility screen

2 Click OK to continue. 3 When the following warning screen displays, click OK to

confirm.

After the Delete Hard Disk Recovery Utility has completed, it assigns the appropriate drive letter (for example, E: drive) for the extra space and formats the drive.

Sample Delete Hard Disk Recovery Utility confirmation screen

Connecting Other External Devices

Using Slim SelectBay® modules

Installing drivers and applications

The TOSHIBA Application Installer allows you to reinstall the drivers and applications that were originally bundled with your computer.

To reinstall drivers and applications:

1 Double-click the Toshiba Application Installer icon on the

Windows desktop. You can also launch the application by clicking Start, All Programs, Hard Disk Recovery

Utilities, and then Toshiba Application Installer.

2 Click Next. 3 Click the item(s) you want to install. 4 Click Install. 5 Follow the on-screen prompts to complete the installation

process.

Using Slim SelectBay® modules

The Slim SelectBay® gives you additional flexibility. By inserting and removing Slim SelectBay modules, you can configure your computer for the task at hand without having to carry unnecessary components with you when you travel. For example, any one of several modules can be used in the Slim SelectBay:

❖ DVD-ROM drive ❖ Multi-function drive ❖ Weight saver insert (a “honeycomb” piece of plastic) that

reinforces the Slim SelectBay for travel

❖ Secondary battery ❖ Secondary hard disk drive (HDD)

Connecting Other External Devices

Using Slim SelectBay® modules

HINT: Items from this list that did not come with your computer can be purchased separately. See the accessories information packaged with your system or visit accessories.toshiba.com.

Removing a module from the Slim SelectBay

NOTE

1 Do one of the following:

2 Slide the Slim SelectBay release toward the back of the

Use caution when lifting or turning your computer. Failure to do so may result in damage to components, such as cables, attached to your computer, or to the computer itself.

❖ Turn off the computer.

❖ Leave the computer on and hot swap the module. First,

stop the module by clicking the Safely Remove Hardware icon on the System tray. After the module is

stopped, it is safe to remove it.

computer.

Sample unlatching the Slim SelectBay module

Connecting Other External Devices

Inserting and removing hard drives

3 Slide the Slim SelectBay module out of the computer.

Sample removing the Slim SelectBay module

If you are removing the weight saver, retain it for transporting the computer when no other module is installed in the Slim SelectBay.

Inserting a module into the Slim SelectBay

To install a module into the Slim SelectBay, simply slide the module all the way into the Slim SelectBay until the latch locks into place.

Inserting and removing hard drives

Your computer can use hard drives with various capacities. Depending upon the original hard drive installed in your computer, you may wish to increase storage capacity by changing the internal drive, or you can add additional hard drive space by inserting a drive into the Slim SelectBay.

To change the internal hard drive.

1 Shut down your computer completely using the Shut down or

Turn Off command. See “Turning off the computer” on

page 57.

2 Unplug the computer.

Connecting Other External Devices

Inserting and removing hard drives

3 Close the display panel and remove any cables that may

be connected.

4 Turn the computer upside down and remove the battery.

See “Changing the main battery” on page 146.

5 Remove the screw on the hard drive bay cover.

Sample removing the hard drive bay cover screw

6 Remove the hard drive bay cover.

Sample removing the hard drive bay cover

7 Lift the hard drive bay cover to expose the hard drive.

Connecting Other External Devices

Inserting and removing hard drives

8 Release the hard drive from the hard drive connector by

grasping the plastic tab on the exposed edge of the hard drive sliding it to the left side of the computer until it is fully disconnected.

Sample sliding the hard drive away from the connector

9 Lift the hard drive out of the hard drive bay.

Sample lifting the hard drive out of the hard drive bay

Connecting Other External Devices

Inserting and removing hard drives

10 Install the new hard drive by placing the drive into the

hard drive bay.

Sample placing the hard drive into the hard drive bay

11 Slide the hard drive into the hard drive connector.

Sample sliding the hard drive into the hard drive connector

12 Press the drive firmly into the connector. Do not force the

drive into the computer.

13 Replace the hard drive bay cover and tighten the screw

removed in step 5.

Connecting Other External Devices

Inserting and removing PC Cards

Your computer comes with one PC Card slot and supports two types of PC Cards:

❖ Type I cards—You can install one of these cards. ❖ Type II cards—You can install one of these cards.

TECHNICAL NOTE: For PCMCIA-compatible PC Cards, check the package to make sure they conform to the PCMCIA 2.1 standard (or later). Other cards may work with your computer, but are likely to be much more difficult to set up and use.

Setting up a PC Card for your computer

Some PC Cards are ready to use as soon as you install them. Others, such as hard disk cards, network cards, and SCSI adapters, may need to be set up to work with your computer. To set up your PC Card, refer to the documentation that came with the card or refer to your operating system manual or online help.

Inserting a PC Card

You can only use PC Cards in the bottom slot or ExpressCards in the top slot. You cannot insert a PC Card into the ExpressCard slot (the upper slot), nor can you insert an ExpressCard into the PC card slot (the lower slot).

Before you insert a PC Card, refer to the documentation that comes with the card to see if you need to do anything before you insert it.

Connecting Other External Devices

Inserting and removing PC Cards

There are two different ways to insert a PC Card:

❖ Turn off the computer and follow the steps below. ❖ Insert the PC card while the computer is running. See

“Hot swapping” on page 95 for more information.

To insert a PC Card with the computer off:

1 Locate the PC Card slot on the left side of the computer.

2 Insert the PC Card in the lower slot.

Sample inserting a PC Card

3 When the card is almost all the way into the slot, push

firmly, but gently, to ensure a firm connection with the computer. Do not force the card into position.

Removing a PC Card

1 If the computer is on, stop the PC Card by clicking the Safely

Remove Hardware icon on the System tray. After the PC

Card stops, it is safe to remove it.

2 Locate the PC Card eject button next to the PC Card slot. 3 Press the PC Card eject button once to extend it, and push

the button in to remove the PC Card.

Sample pressing the PC card eject button

The PC Card ejects slightly from the slot.

4 Grasp the edges of the PC Card and slide it out of the

slot.

Hot swapping

With PC Cards, you can replace one PC Card with another while the computer is on. This is called “hot swapping.”

Connecting Other External Devices

Inserting and removing PC Cards

Hot swapping precautions

Although you can insert a PC Card at any time, remember not to remove a card while it is in use. Otherwise, you could lose valuable information.

For example:

❖ Do not remove a hard disk card while the system is

accessing it.

❖ Do not remove a network card while you are connected to

a network.

❖ Do not remove a SCSI card while any of the SCSI

devices connected to it are operating.

Before removing a PC Card, stop it by clicking the Safely Remove Hardware icon on the System tray. After the PC Card is stopped, it is safe to remove.

Connecting Other External Devices

Inserting an ExpressCard™

Before you insert an ExpressCard, refer to the documentation that comes with the card to see if you need to do anything before you insert it.

To insert an ExpressCard:

1 Turn off the computer.

You may also hot swap an ExpressCard. Stop the ExpressCard by clicking the Safely Remove Hardware icon on the System tray. After the ExpressCard is stopped, it is safe to remove.

2 Locate the ExpressCard slot just above the PC Card slot

on the left side of the computer.

3 Insert the ExpressCard. 4 When the card is almost all the way into the slot, push

firmly, but gently, to ensure a firm connection with the computer. Do not force the card into position.

Removing an ExpressCard™

Stop the ExpressCard by clicking the Safely Remove Hardware icon on the System tray. After the ExpressCard is

stopped, it is safe to remove. Press the card until it pops out, and then remove it.

Connecting Other External Devices

Inserting an SD™ card

Important: Do not use the Copy Disk function for SD cards. In order to copy data from one SD card to another, use the following procedure:

1 Format the target SD card in the same format as the source SD

card.

2 Insert the source SD card. 3 Create a temporary folder on the hard disk drive. 4 Copy the contents of the source SD card into the

temporary folder you created in step 3.

5 Remove the source SD card. 6 Insert the target SD card created in step 1. 7 Copy the file contents from the temporary folder to the

target SD card.

8 Eject the target SD card.

Inserting an SD™ card

NOTE

Locate the SD card slot on the left side of the computer. To insert an SD card:

1 Turn the card so that the connector (metal area) faces down,

MMC cards (multimedia cards) do not work in this slot.

then push the card into the slot until it locks in place.

If Windows it, verify that the card is facing the right way, and insert it again.

The SD light on the front of the computer glows green when the card is being accessed.

does not recognize an inserted SD card, remove

Connecting Other External Devices

Connecting your modem to a telephone line

To remove an SD card:

1 Press the card inward to release it and the card will pop out

slightly.

Do not touch the SD connector. You could expose the storage area to static electricity which can destroy data.

Do not remove media while data is being written or read. Even when the Windows message “copying...” disappears, writing to the media might still be in progress and your data could be destroyed. Wait for the indicator light to go out.

Connecting your modem to a telephone line

Your computer comes with a built-in modem that can be connected to a standard voice-grade telephone line.

Use the modem to:

❖ Access the Internet. ❖ Communicate with your office’s local area network

(LAN) or a larger corporate wide area network (WAN). For specific information about connecting to a LAN or WAN,

consult your network administrator.

❖ Send a fax directly from your computer.

Connecting to a phone line

Before you can communicate using the modem, you need to connect it to a telephone line. Your computer’s built-in modem port uses an RJ-11 jack to connect the modem to a standard voice-grade telephone line.

Connecting Other External Devices

Connecting your modem to a telephone line

1 Plug one end of the telephone cable (purchased separately)

into the modem port on the back of the computer.

Sample connecting the telephone cable to the modem port

2 Connect the other end to the RJ-11 wall jack.

Sample connecting to a wall jack

The modem is designed for use with a standard analog telephone line. Do not connect the modem to a digital telephone line. A digital line will damage the modem.

Now you are ready to send a fax or use the modem to connect to an online service or the Internet.

For more information on using a modem, see “Setting up for

communications” on page 162.

Connecting Other External Devices

100

Using the i.LINK® port

The i.LINK® port on the left side of the computer provides an extremely fast data transfer rate.

In addition to high speed, the i.LINK isochronous data transfer (the delivery of data at a guaranteed rate). This makes it ideal for devices that transfer high levels of data in real-time, such as video devices.

As with USB ports, the i.LINK Play (automatic configuration) and hot swapping (the ability to connect and disconnect devices while the computer is on).

port also supports

port supports both Plug-and-

Toshiba Tecra M3 Series, M3-S212TD, M3-S311, M3-S336, M3-S636 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Tecra® M3 Series User’s Guide

Contents

Introduction

This guide

Safety icons

Other documentation

Other icons used

Service options

Selecting a place to work

Creating a computer-friendly environment

Keeping yourself comfortable

Precautions

Setting up your computer

Important information on your computer’s cooling fan

Setting up your software

Registering your computer with Toshiba

Adding external devices

Connecting to a power source

Using the main battery

Using the computer for the first time

Your computer’s features and specifications

Turning on the power

Turning off the computer

Caring for your computer

Closing the display panel

Cleaning the computer

Moving the computer

Using a computer lock

Using external display devices

Connecting the display device

Directing the display output when you turn on the computer

Adjusting the quality of the external display

Video limitations

Using an external keyboard

Connecting a keyboard

Using a mouse

Making your external keyboard emulate the Fn key

Connecting a mouse

Connecting a local printer

Connecting a USB printer

Connecting a parallel printer

Connecting an optional external diskette drive

Connecting external speakers or headphones

Connecting an external microphone

Using an expansion device

Adding memory

Installing memory modules

Hard Drive Recovery Utilities

Creating Recovery CDs/DVDs

Hard Disk Drive Recovery using the recovery partition

Hard Disk Drive Recovery using the Recovery media

Deleting the Hard Disk Recovery Utility

Using Slim SelectBay® modules

Installing drivers and applications

Inserting and removing hard drives

Inserting and removing PC Cards

Setting up a PC Card for your computer

Inserting a PC Card

Removing a PC Card

Hot swapping

Inserting an ExpressCard™

Removing an ExpressCard™

Inserting an SD™ card

Connecting your modem to a telephone line

Connecting to a phone line

Using the i.LINK® port