Page 1
FIELD REPLACEABLE UNIT DOCUMENTATION
9000 Series
Tecra
TM
TM
9000 Series
Tecra
TM
9000 Series
Tecra
GENERAL INFORMATION
TM
9000 Series
Tecra
TM
TM
9000 Series
Tecra
TM
9000 Series
Tecra
GENERAL INFORMATION
TM
9000 Series
Tecra
TM
TM
9000 Series
Tecra
TM
9000 Series
Tecra
TM
9000 Series
Tecra
TM
TM
9000 Series
Tecra
TM
9000 Series
Tecra
GENERAL INFORMATION
TM
9000 Series
Tecra
TM
TM
9000 Series
Tecra
TM
9000 Series
Tecra
GENERAL INFORMATION
TM
9000 Series
Tecra
GENERAL INFORMATION
TM
9000 Series
Tecra
TM
TM
9000 Series
Tecra
TM
9000 Series
Tecra
TM
9000 Series
Tecra
TM
TM
9000 Series
Tecra
TM
9000 Series
Tecra
TM
9000 Series
Tecra
TM
TM
9000 Series
Tecra
TM
TM
9000 Series
Tecra
TM
9000 Series
Tecra
TM
TM
TM
Tecra
9000 Series
GENERAL INFORMATION
Tools Required for Proper
Disassembly and Reassembly:
Before attempting any of the following procedures,
make sure that the main battery and AC adaptor is
not connected to the unit and the environment in
which you are working on is protected from
Electro-Static Discharge(ESD).
1. Phillips Screwdriver (Size 0&1)
2. Flat head Screwdriver
3. Security Torx (Size 7)
4. Case Separator
5. ESD Wrist Strap
6. ESD mats
7. Tweezers
TOSHIBA
Tough Enough for Today’s World.
Download service manual and resetter printer at http://printer1.blogspot.com
Page 2
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Tecra
9000 Series
TABLE OF CONTENTS:
1. BATTERY PACK REMOVAL
2. OPTIONAL PC CARD REMOVAL
3. SELECT BAY REMOVAL
4. CD-R/W/DVD-ROM DRIVE DISASSEMBLY
5. MEMORY MODULE REMOVAL
6. BLUETOOTH CARD REMOVAL
7. HDD REMOVAL
8. KEYBOARD REMOVAL
9. MODEM BOARD REMOVAL
10 WIRELESS LAN CARD REMOVAL
11. TOP COVER REMOVAL
12. COOLING MODULE REMOVAL
13. CPU REMOVAL
14. MICROPHONE REMOVAL
15. SD/SOUND BOARD REMOVAL
16. RTC BATTERY REMOVAL
17. LED/BLUETOOTH BOARD REMOVAL
18. TOP PCB REMOVAL
19. BOTTOM PCB REMOVAL
20. MEMBRANE SWITCH REMOVAL
21. SPEAKERS REMOVAL
22. 14.1’’ DISPLAY MASK REMOVAL
23. FL INVERTER AND 14.1’’ LCD REMOVAL
TOSHIBA
Tough Enough for Today’s World.
Download service manual and resetter printer at http://printer1.blogspot.com
Page 3
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Tecra
9000 Series
BATTERY PACK REMOVAL
Release
lever
Battery
Pack
1. Turn the computer upside down as shown.
2. Slide the battery release lever in the direction of the
arrow.
3. Lift out the battery.
SELECT BAY REMOVAL
OPTIONAL PC CARD REMOVAL
PC card
Eject button
1. Press the eject button for the PC card you want to
remove.
2. Press the extended eject button to pop the PC Card
out.
3. Grasp the PC card and remove it.
NOTE: Before removing any PC Card device, make sure
it is “STOPPED” in the PC Card manager.
CD-R/W/DVD-ROM DRIVE DISASSEMBLY
Release lever
1. Turn the computer upside down.
2. Slide the release lever in the direction of the arrow.
3. Pull out the select bay device in the direction of the
arrow.
Select bay
device
TOSHIBA
CD-R/W/DVD-ROM
drive
Base cover
Connector
M2x8 silver
screws
1. Remove five M2x3 silver screws securing the base
cover and lift off the base cover.
2. Remove two M2x8 silver screws securing the
connector cover.
3. Remove the connector and the connector cover
from the CD- R/W/DVD-ROMdrive.
M2x3 silver
screws
Connector cover
Tough Enough for Today’s World.
Download service manual and resetter printer at http://printer1.blogspot.com
Page 4
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Tecra
9000 Series
MEMORY MODULE REMOVAL
M2.5x2.8
silver flat
head screws
Memory cover
1. Turn the computer upside down.
2. Remove two M2.5x2.8 silver flat head screws
and remove the memory cover.
BLUETOOTH CARD REMOVAL
Bluetooth cover
1. Remove one M2x4 black security torx screw securing
the bluetooth cover.
2. Lift out the bluetooth cover.
M2x4 black security torx screw
Memory clips
3. Spread the memory clips outward and pull the
memory module out of the connector on a
45 degree angle.
Plastic insulator
3. Disconnect the coaxial cable from the bluetooth card.
4. Lift up the plastic insulator to disconnect the card.
Bluetooth card
Coaxial cable
TOSHIBA
Tough Enough for Today’s World.
Download service manual and resetter printer at http://printer1.blogspot.com
Page 5
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Tecra
9000 Series
HDD REMOVAL
M2.5x8 silver screw
HDD cover
1. Turn the computer upside down.
2. Remove one M2.5x8 silver screw securing HDD cover.
3. Remove the HDD cover.
HDD REMOVAL
Plastic Tab
4. Unfold the plastic tab and pull to remove the HDD
from the bay.
KEYBOARD REMOVAL
HDD pack
HDD
bracket
HDD connector
5. Remove four M3x4 brass flat head screws securing
the HDD to the bracket and lift the drive out of the
bracket.
6. Unplug the HDD connector from the drive.
HDD
M3x4 flat head brass screws
TOSHIBA
M2.5x16 silver screw
1. Turn the computer upside down.
2. Remove one M2.5x16 silver screw securing the
keyboard on the bottom cover.
Tough Enough for Today’s World.
Download service manual and resetter printer at http://printer1.blogspot.com
Page 6
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Tecra
9000 Series
KEYBOARD REMOVAL
Latch
Keyboard
Keyboard holder
2. Turn the computer right side up and open the display
panel.
3. Using the case separator, unlatch the keyboard holder
at the top of the keyboard.
KEYBOARD REMOVAL
Keyboard
Keyboard
cable
PJ123
5. Lift out the keyboard and set it as shown above(Place
an insulator between the keyboard and the LCD to
prevent scratches on the LCD).
6. Disconnect the keyboard cable from PJ123 on the
system board.
M2.5x2.8 silver screws
4. Remove two M2.5x2.8 silver screws securing the
keyboard.
MODEM BOARD REMOVAL
Modem
board
M2x4 brass screws
1. Remove two M2x4 brass screws securing the
modem board.
2. Disconnect the modem board from PJ125 on the
system board.
TOSHIBA
Tough Enough for Today’s World.
Download service manual and resetter printer at http://printer1.blogspot.com
Page 7
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Tecra
9000 Series
WIRELESS LAN CARD REMOVAL
Mini-PCI
connector
clips
Mini PCI cover
1. Remove one M2x4 security torx screw securing
the mini PCIcover and lift out the cover.
M2.5x4 security torx screw
TOP COVER REMOVAL
M2.5x8 silver screws
M2.5x4
black flat
head
screw
M2.5x16 silver screws
1. Turn the computer upside down and remove the
following screws:
-2 M2.5x2.8 silver flat head screws
-1 M2.5x4 black flat head screw
-4 M2.5x8 silver screws
-4 M2x12 silver screws
-6 M2.5x16 silver screws
2. Turn the computer right side up and open the display.
M2.5x2.8
silver flat
head screws
M2x12
silver
screws
Wireless LAN card
2. Disconnect the black and white coax from the
wireless LAN card.
3. Spread the Mini-PCI connector clips and pull the
Wireless LAN card out of the connector about
45 degree angle.
Glass tape
PJ127
Speaker
cable
M2.5x8 silver screws
3. Disconnect the speaker cable from PJ127 and the
membrane switch cable from PJ122 on the top board
4. Remove the glass tape securing the LCD/FL cable
and disconnect the cable from the bottom board.
5. Remove two M2.5x8 silver screws and one M2.5x14
black screw from the keyboard area.
5. Lift out the top cover assembly.
Note: When installing the top cover, ensure that the bluetooth
coaxial cable is properly routed to the Bluetooth slot.
Black coax cable
M2.5x14 black screw
Membrane switch cable
White coax cable
LCD/FL cable
PJ122
TOSHIBA
Tough Enough for Today’s World.
Download service manual and resetter printer at http://printer1.blogspot.com
Page 8
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Tecra
9000 Series
COOLING MODULE REMOVAL
Cooling
module
Fan cable
M2.5x10
black flat
head screws
Glass tape
1. Remove the glass tape securing the fan cable and
disconnect the cable from PJ770 on the top board.
2. Remove four M2x10 black flat head screws securing
the cooling module.
3. Lift out the cooling module.
PJ770
MICROPHONE REMOVAL
CPU REMOVAL
CPU
Open
Thermal conductor
1. Peel off the thermal conductor.
2. Insert a flat head screwdriver and rotate it
counter-clockwise to unlock the CPU lock.
3. Lift out the CPU.
Close
CPU lock
SD/SOUND BOARD REMOVAL
Microphone
1. Disconnect the microphone cable from PJ1003 on the
SD/Sound board.
2. Lift out the microphone.
Microphone cable
PJ1003
SD
interface
cable
PJ1001
Sound
interface
cable
PJ1000
SD/Sound board
1. Disconnect the SD interface cable from PJ1001 and
sound interface cable from PJ1000 on the
SD/sound board.
2. Remove two M2.5x4 brass screws securing the
SD/Sound board.
3. Lift out the SD/Sound board.
M2.5x4 brass screws
TOSHIBA
Tough Enough for Today’s World.
Download service manual and resetter printer at http://printer1.blogspot.com
Page 9
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Tecra
9000 Series
RTC BATTERY REMOVAL
PJ5
1. Remove the plastic insulator.
2. Disconnect the RTC cable from PJ5 on the
LED/Bluetooth board.
3. Lift out the RTC battery.
RTC cable
TOP PCB REMOVAL
This is where
top and bottom
board interconects
RTC
battery
Plastic insulator
LED/BLUETOOTH BOARD REMOVAL
M2.5x8
silver
screw
M2.5x4 brass screwsLED/Bluetooth board
1. Remove two M2.5x4 brass screws and one M2.5x8
silver screw securing the LED/Bluetooth board.
2. Disconnect the LED/Bluetooth board from PJ105
on the top PCB.
Modem cable
PJ801
Power
cable
M2.5x16 black screw
1. Disconnect the power cable from PJ801 on the top PCB.
2. Remove two M2.5x4 brass screws and one M2.5x16
black screw securing the top PCB.
3. Gently lift up the right side of the top board to disconnect
from PJ19 on the top PCB.
M2.5x4 brass screws
TOSHIBA
Tough Enough for Today’s World.
Download service manual and resetter printer at http://printer1.blogspot.com
Sound interface
cable
PC card slot
SD interface cable
4. Remove the PC card slot from PJ117 on the top PCB.
5. Disconnect the following cables from the top PCB:
-Sound interface cable from PJ102
-SD interface cable from PJ103
-Modem cable from PJ126
Page 10
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Tecra
9000 Series
BOTTOM PCB REMOVAL
M2.5x4
brass
screws
Bottom
board
PJ18
1. Disconnect the battery harness from PJ18 on the
bottom PCB.
2. Remove five M2.5x4 brass screws securing the bottom
PCB.
3. Lift out the bottom PCB.
SPEAKERS REMOVAL
Battery harness
MEMBRANE SWITCH REMOVAL
Membrane
switch assy
M2.5x3 silver screws
1. Remove three M2.5x3 flat head silver screws
securing the membrane switch.
2. Lift out the membrane switch assembly.
Left and right
speakers
M2.5x4 brass screws
1. Remove four M2.5x4 brass screws securing the left
and right speakers.
2. Lift out the speakers.
TOSHIBA
Tough Enough for Today’s World.
Download service manual and resetter printer at http://printer1.blogspot.com
Page 11
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Tecra
9000 Series
14.1” DISPLAY MASK REMOVAL
Latch
Display
mask
LCD
Mask seals
1. Remove two mask seals at the bottom corners of the
display assembly using a pair of fine-tipped tweezers.
2. Remove two M2.5x6 flat head brass screws securing
the display mask.
3. There are 23 latches securing the display mask.
Carefully insert your fingers between the mask and the
LCD panel and pry open the latches starting from the
six top latches, to the five latches on each right
and left sides, ending with the bottom seven latches.
FL INVERTER AND 14.1” LCD REMOVAL
Mask
seals
M2x4
brass
screws
LCD/
FL cable
FL inverter board
1. Remove one M2x2.8 silver screw securing the
FL inverter board.
2. Carefully lift up the FL inverter board and
disconnect the LCD/FL cable from CN1 and the
FL cable from CN2.
3. Remove four mask seals to expose four screws
securing the LCD module assembly.
4. Remove four M2X2.8 brass screws securing the
LCD module assembly.
5. Carefully rotate out the top of the LCD module
enough to access the display cable
6. Peel off the tape securing the LCD/FL cable and
disconnect the cable.
7. Remove four M2x2.8 silver screws securing the
right and left LCD brackets.
M2x3 silver screw
LCD module
Mask
seals
M2x4
brass
screws
FL cable
TOSHIBA
Tough Enough for Today’s World.
Download service manual and resetter printer at http://printer1.blogspot.com
Loading...