Toshiba TEC B-443, TEC B-443–QP Owner's Manual
TEC Bar Code Printer
B-443
Owner’ s Manual
LIST OF STANDARDS OF CONFORMITY
Manufacturer : TOSHIBA TEC Corporation
Address : 570 Ohito, Ohito-cho, Tagata-Gun, Shizuoka-ken, 410-2392
Japan
declares that following product
Product Name : Bar Code Printer
Model : B-443-QP
Options : All
conforms to the following product specifications
Safety : EN 60950
EMC : EN 55022
EN 50082-1
Supplementary Information
The product herewith complies with the requirements of the Low Voltage Directive 73/23/
ECC, and the EMC directive 89/336/ECC.
TÜV / GS
Wichtige Sicherheitshinweise
1. Bitte lesen Sie diese Hinweise sorgfältig durch.
2. Bewahren Sie diese Anleitung für den späteren Gebrauch auf.
3. Vor dem Reinigungsvorgang ist der Drucker von Stromnetz zu trennen.
Verwenden Sie keine Flüssig-oder Aerosolreiniger. Am besten eignet sich ein
angefeuchtetes Tuch.
4. Die Netzsteckdose sollte nah am Drucker liegen und leicht zugänglich sein.
5. Der Drucker ist vor Feuchtigkeit zu schützen.
6. Bei der Aufstellung ist auf einen sicheren Stand der Druckers zu achten. Ein
Kippen oder Fallen könnte Beschädigungen hervorrufen.
7. Beachten Sie die Anschlußwerte der Druckers beim Anschluß an das Stromnetz.
8. Diese Gerät kann bis zu einer Außentemperatur von maximal 40oC betrieben
werden.
Copyright © 1999
by TOSHIBA TEC CORPORATION
All Right s Reserved
570 Ohito, Ohito-cho, Tagata-gun, Shizuoka-ken, JAPAN
EO1-33013
i
CAUTION:
1. This manual may not be copied in whole or in part without prior written
permission of TOSHIBA TEC.
2. The contents of this manual may be changed without notification.
3. Please refer to your local Authorized Service representative with regard to any
queries you may have in this manual.
Changes or modifications not expressly approved by manufacturer for compliance could
void the user’ s authority to operate the equipment.
CAUTION:
To avoid injury, be careful not to catch or jam your fingers while opening or closing the
cover.
CAUTION:
Do not touch moving parts. To reduce the risk that fingers, jewelry, clothing, etc., be drawn
into the moving parts, push the switch in the “OFF” position to stop movement.
EO1-33013
ii
CONTENTS
1. PRODUCT INTRODUCTION................................................................ 1
1.1 Compliances.....................................................................................................1
2. GETTING STARTED............................................................................. 2
2.1 Applicable Model..............................................................................................2
2.2 Unpacking and Inspection................................................................................2
2.3 Equipment Checklist.........................................................................................2
2.4 Printer Parts......................................................................................................4
2.5 External Label Roll Mount ................................................................................7
2.6 Buttons and Indicators......................................................................................8
3. SET UP.................................................................................................. 9
3.1 Setting Up the Printer.......................................................................................9
3.2 Loading Label and Tag Stock ........................................................................... 9
3.3 Self-Peeling Function.....................................................................................12
3.4 Ribbon Loading Instructions...........................................................................14
3.5 Install External Label Roll Mount....................................................................17
3.6 Install Memory Module....................................................................................18
3.7 Self Test .........................................................................................................19
3.8 Dump Mode....................................................................................................20
4. USING B-443 ...................................................................................... 21
4.1 Power-on Utilities............................................................................................21
4.1.1 Self Test Utility........................................................................................21
4.1.2 Gap Sensor Calibration Utility.................................................................21
4.1.3 Printer Initialization..................................................................................22
4.2 Error Messages..............................................................................................23
4.3 Troubleshooting Guide...................................................................................24
5. SPECIFICATIONS, OPTIONS, & SUPPLIES .................................... 25
5.1 Specifications .................................................................................................25
5.1.1 Printer. .................................................................................................... .25
5.1.2 Indicators and Buttons.............................................................................25
5.1.3 Communication Interface.........................................................................25
5.1.4 Power Requirements...............................................................................25
5.1.5 Environment ............................................................................................26
5.1.6 Printer Body.............................................................................................26
EO1-33013
iii
5.2 Options...........................................................................................................26
5.3 Supplies .......................................................................................................... 27
5.3.1 Label Stock..............................................................................................27
5.3.2 Ribbon.....................................................................................................27
iv
EO1-33013
Safety Summary
Personal safety in handling or maintaining the equipment is extremely important. Warnings and Cautions
necessary for safe handling are included in this manual. All warnings and cautions contained in this
manual should be read and understood before handling or maintaining the equipment.
Do not attempt to effect repairs or modifications to this equipment. If a fault occurs that cannot be rectified
using the procedures described in this manual, turn off the power, unplug the machine, then contact your
authorized TOSHIBA TEC representative for assistance.
Meanings of Each Symbol
This symbol indicates warning items (including cautions).
Specific warning contents are drawn inside the symbol.
(The symbol on the left indicates a general caution.)
This symbol indicates prohibited actions (prohibited items).
Specific prohibited contents are drawn inside or near the symbol.
(The symbol on the left indicates “no disassembling”.)
This symbol indicates actions which must be performed.
Specific instructions are drawn inside or near the symbol.
(The symbol on the left indicates “disconnect the power cord plug from the outlet”.)
Do not use voltages other than the
voltage (AC) specified on the rating
plate, as this may cause fire or
electric shock.
Any other than the
specified AC voltage
is prohibited.
WARNING
This indicates that there is the risk of death or serious injury if the
machines are improperly handled contrary to this indication.
Prohibited
Do not plug in or unplug the power
cord plug with wet hands as this may
cause electric shock.
Do not place metal objects or
water-filled containers such as flower
vases, flower pots or mugs, etc. on
top of the machines. If metal objects
or spilled liquid enter the machines,
this may cause fire or electric
shock.
If the machines share the same
outlet with any other electrical
appliances which consume large
amounts of power, the voltage will
fluctuate widely each time these
appliances operate. Be sure to
provide an exclusive outlet for the
machine as this may cause the
machines to malfunction.
Do not insert or drop metal,
flammable or other foreign objects into
the machines through the ventilation
slits, as this may cause fire or electric
shock.
Prohibited
Prohibited
Prohibited
Do not scratch, damage or modify
the power cords. Also, do not place
heavy objects on, pull on, or excessively bend the cords, as this may
cause fire or electrical shock.
Prohibited
Continued use of the machines in an
abnormal condition such as when the
machines are producing smoke or
strange smells may cause fire or elec-
tric shock. In these cases, immediately turn off the power switches and
disconnect the power cord plugs from
the outlet. Then, contact your authorized TOSHIBA TEC representative for
assistance.
Disconnect
the plug.
If the machines are dropped or their
cabinets damaged, first turn off the
power switches and disconnect the
power cord plugs from the outlet, and
then contact your authorized
TOSHIBA TEC representative for
assistance. Continued use of the
machine in that condition may cause
fire or electric shock.
Disconnect
the plug.
v
EO1-33013
CAUTION
This indicates that there is the risk of personal Injury or damage to
objects if the machines are improperly handled contrary to this indication.
If foreign objects (metal fragments,
water, liquids) enter the machines,
first turn off the power switches and
disconnect the power cord plugs from
the outlet, and then contact your
authorized TOSHIBA TEC representative for assistance. Continued
use of the machine in that condition
may cause fire or electric shock.
Disconnect
the plug.
Do not remove covers, repair or
modify the machine by yourself. You
may be injured by high voltage, very
hot parts or sharp edges inside the
machine.
No disassembling.
Ensure that the equipment is
properly grounded. Extension cables
should also be grounded. Fire or
electric shock could occur on
improperly grounded equipment.
Connect a
grounding
wire.
When unplugging the power cords,
be sure to hold and pull on the plug
portion. Pulling on the cord portion
may cut or expose the internal wires
and cause fire or electric shock.
Disconnect
the plug.
Precautions
The following precautions will help to ensure that this machine will continue to function correctly.
• Try to avoid locations that have the following adverse conditions:
* Temperatures out of the specification * Direct sunlight * High humidity
* Shared power source * Excessive vibration * Dust/Gas
• The cover should be cleaned by wiping with a dry cloth or a cloth slightly dampened with a mild
detergent solution. NEVER USE THINNER OR ANY OTHER VOLATILE SOLVENT on the plastic
covers.
• USE ONLY TOSHIBA TEC SPECIFIED paper and ribbons.
• DO NOT STORE the paper or ribbons where they might be exposed to direct sunlight, high temperatures, high humidity, dust, or gas.
• Ensure the printer is operated on a level surface.
• Any data stored in the memory of the printer could be lost during a printer fault.
• Try to avoid using this equipment on the same power supply as high voltage equipment or equipment likely to cause mains interference.
• Unplug the machine whenever you are working inside it or cleaning it.
• Keep your work environment static free.
• Do not place heavy objects on top of the machines, as these items may become unbalanced and fall
causing injury.
• Do not block the ventilation slits of the machines, as this will cause heat to build up inside the
machines and may cause fire.
• Do not lean against the machine. It may fall on you and could cause injury.
• Care must be taken not to injure yourself with the printer paper cutter.
• Unplug the machine when it is not used for a long period of time.
Request Regarding Maintenance
• Utilize our maintenance services.
After purchasing the machine, contact your authorized TOSHIBA TEC representative for assistance
once a year to have the inside of the machine cleaned. Otherwise, dust will build up inside the
machines and may cause a fire or a malfunction. Cleaning is particularly effective before humid
rainy seasons.
• Our preventive maintenance service performs the periodic checks and other work required to
maintain the quality and performance of the machines, preventing accidents beforehand.
For details, please consult your authorized TOSHIBA TEC representative for assistance.
• Using insecticides and other chemicals
Do not expose the machines to insecticides or other volatile solvents. This will cause the cabinet or
other parts to deteriorate or cause the paint to peel.
EO1-33013
1
1. PRODUCT INTRODUCTION
Thank you very much for purchasing TEC B-443 bar code printer. The attractive
desktop printer delivers superior performance at an economical price. Both
powerful and easy-to-use, B-443 printer is your best choice among desktop
direct thermal and thermal transfer label printers.
B-443 printer offers both thermal transfer and direct thermal printing at
selectable speeds of 1.5, 2.0 and 3.0 inches per second. It can accept a wide
range of media, including roll feed, die-cut, and fan-fold labels or tags for both
thermal transfer and direct thermal printing. All of the most frequently used bar
code formats are available. Fonts and bar codes can be printed in any one of
four directions. B-443 printer provides a choice of five different sizes of
alphanumeric fonts. By using font multiplication, an even greater range of sizes
is possible. Smooth fonts can be downloaded from the user friendly, “Label
Design” Windows software. In addition, B-443 is capable of independently
executing BASIC programming functions, including arithmetic, logical operation,
loop, flow-control and file management, among others. This programming
capability provides the greatest efficiency in label printing. The status of printer
and error messages may either be printed out or viewed on a monitor by means
of the RS-232 connection.
1.1 Compliances
CE, TÜV-GS
EO1-33013
2
2. GETTING STARTED
2.1 Applicable Model
B - 4 4 3 – Q P
Destination Code
QP: Europe
GH12-GB: UK
2.2 Unpacking and Inspection
The printer has been specially packaged to withstand damage in the shipping
process. However, for fear that unexpected damage might occur, upon receiving
the bar code printer, carefully inspect the package and the device. In case of
evident damage, contact the carrier directly to specify the nature and extent of
the damage. Please retain the packaging materials in case you need to reship
the printer.
2.3 Equipment Checklist
l One B-443 bar code printer unit
l Ribbon paper core
l Ribbon supply/rewind spindle (2 pcs.)
l Label supply roll spindle
l External label roll mount
l Power supply
l Power cord
l Centronics interface cable
l Windows driver
l Label Design Windows software
Separately purchased items may also be included. These additional items may
include:
l Additional labels
l Additional ribbons
l Memory module
l Cutter
EO1-33013
3
l Portable LCD keyboard
If any parts are missing, please contact the Customer Service Department of
your purchased reseller or distributor.
EO1-33013
4
2.4 Printer Parts
Figure 1. Top front view
1. Cover Release Button
2. PWR., ON-LINE and ERR. Indicators
3. PAUSE Button
4. FEED Button
5. Label Dispense Opening
6. Backing Paper Opening (for use with self-peeling function)
1
2
3
4
5
6
Loading...