Toshiba TDP-TW420U, TDP-T420U User Manual
TDP-TW420
DATA PROJECTOR
OWNER’S MANUAL
Before UsingPreparationsOperationsMaintenanceOthers
Network and
USB memory
In the spaces provided below, record the Model and Serial No. located at the bottom of
your projector.
Model No. Serial No.
Retain this information for future reference.
2
3
Before Using
Before Using
SAFETY PRECAUTIONS
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to
the presence of important operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES
ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE CABINET.
REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
WARNING:
USA only
USA only
MODEL NAME: TDP-TW420
TRADE NAME: DATA PROJECTOR MODEL NAME: TDP-TW420
FOR HOME OR OFFICE USE
Handling the cord on this product or cords associated with accessories sold with
this product, will expose you to lead, a chemical known to the State of California
to cause birth defects or other reproductive harm. Wash hands after handling.
Lamp contains mercury. Disposal of this product may be regulated due to
environmental considerations. For disposal, reuse or recycling information,
please contact your local government or the Electronic Industries Alliance at
www.eiae.org.
USA only
Tested To Comply
With FCC Standards
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RESPONSIBLE PARTY: TOSHIBA AMERICA INFORMATION SYSTEMS, INC.
CAUTION:
USA only
Notice:
CANADA only
9740 Irvine Blvd., Irvine, CA 92618-1697 U.S.A
Phone: (949) 583-3000
Changes or modifications made to this equipment, not expressly approved by
Toshiba, or parties authorized by Toshiba, could void the user’s authority to
operate the equipment.
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil
numérique de la classe B est conforme à la norme NMB-003 du Canada.
FCC NOTICE: This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
4
5
Before Using
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND
INSTRUCTIONS GIVEN IN THIS OWNER'S MANUAL AND THOSE
MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR FUTURE
REFERENCE.
This unit is fully transistorized and does not contain any parts that can be repaired by the
user.
WARNING: DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE
EXPOSED TO DANGEROUS VOLTAGE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL ONLY.
1. Read Owner’s Manual
After unpacking this product, read
the owner's manual carefully, and
follow all the operating and other
instructions.
2. Power Sources
This product should be operated
only from the type of power source
which does not exceed the voltage
range specified on the rating label
and the power cord.
If you are not sure of the type
of power supply to your home,
consult your product dealer or local
power company.
3. Source of Light
Do not look into the lens while the
lamp is on. The strong light from
the lamp may cause damage to
your eyesight.
4. Ventilation
Openings in the cabinet are
provided for ventilation and to
ensure reliable operation of the
product and to protect it from
overheating. These openings must
not be blocked or covered. Never
block an opening by placing the
product on a bed, sofa, rug or
other similar surface. Do not place
it in a built-in installation such as
a bookcase or rack, unless proper
ventilation is provided.
5. Heat
6. Water and Moisture
7. Cleaning
The product should be situated
away from heat sources such as
radiators, heat registers, stoves,
or other products (including
amplifiers) that produce heat.
Do not use this product near water.
- for example, near a bath tub,
wash bowl, kitchen sink, or laundry
tub; in a wet basement; or near a
swimming pool and the like.
Unplug this product from the wall
outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners.
Always use a soft cloth for
cleaning.
8. Be sure that you firmly
insert the plug into the wall
outlet.
Incorrect or faulty connections
may result in fire or electric shock.
Avoid using an unsound or loose
outlet.
9. Power Cord Protection
Power cords should be routed
so that they are not likely to be
walked on or pinched by items
placed upon or against them,
paying particular attention to cords
at plugs, convenience receptacles,
and the point where they exit from
the product.
10. Overloading
Do not overload wall outlets. To
reduce the risk of electric shock,
do not use the polarized plug with
an extension cord , receptacle, or
other outlet unless the blades can
be inserted completely with threewire grounding type to prevent
blade exposure. Failure to follow
these instructions may result in fire
or electric shock.
6
7
Before Using
IMPORTANT SAFETY INSTRUCTIONS (Continued)
S3125A
11. Lightning storms
For added protection for this
product during a storm, or when it
is left unattended and unused for
long periods of time, unplug it from
the wall outlet. This will prevent
damage to the product due to
lightning and power-line surges.
Never operate this unit on AC
power during a thunderstorm. If
you see lightning or hear thunder,
never touch the unit, cables and/or
peripherals. An electric surge
caused by the storm, may result in
an electrical shock or damage to
the unit.
12. Object and Liquid Entry
Never push objects of any kind into
this product through openings as
they may touch dangerous voltage
points or short-out parts that could
result in a fire or electric shock.
Never spill liquid of any kind on the
product.
13. Do not place or keep the
projector within the reach
of the children.
It may fall or tip over, possibly
causing serious injury.
14. Do not place the product
vertically
Do not use the product in the
upright position or any other
vertical positions to project the
pictures. It may fall which could
result in serious injury and/or
damage to the product.
15. Stack Inhibited
Do not stack other equipment on
this product and do not place this
product on other equipment. The
top and bottom surface of this
product increase in temperature
during normal use and may
damage the other unit.
16. Moving the projector
When carrying the projector, be
sure to use the carrying handle to
avoid any damage to the lens or
main unit.
17. Attachments
Do not use attachments not
recommended by the product
manufacturer.
Use of an incompatible
attachments could cause hazards
or damage to the product.
18. Accessories
19. Damage Requiring Service
a) The power supply cord or plug is
b) Liquid has been spilled, or objects
c) The product has been exposed to
d) The product does not operate
e) The product has been dropped or
Do not place this product on
an unstable cart, stand, tripod,
bracket, or table. The product may
fall, causing serious injury to a
child or adult, and serious damage
to the product. A product and cart
combination should be moved with
care. Quick stops, excessive force,
and uneven surfaces may cause
the product and cart combination
to overturn.
Unplug this product from the wall
outlet and take the product to
qualified service personnel if you
encounter any of the following
conditions:
damaged.
have fallen into the product.
rain or water.
normally when following the
operating instructions. Adjust only
those controls that are covered by
the operating instructions since
an improper adjustment of other
controls may result in damage and
will often require extensive work by
a qualified technician to restore the
product to its normal operation.
damaged in any way (If the cabinet
should break, please handle with
care to avoid injury).
f) The product exhibits a distinct
change in performance, which
indicates a need for service.
20. If glass components,
including lens and lamp,
should break, contact your
dealer for repair service.
This product incorporates glass
components, including a lens and
a lamp.
If these should break, please
handle with care to avoid injury
and contact your dealer for repair
service. Avoid any broken pieces
of glass since they may cause
injury. In the unlikely event that the
lamp ruptures, thoroughly clean
the area around the projector and
discard any edible items placed
in that area since they may be
contaminated.
21. Servicing
Do not attempt to service this
product yourself as opening or
removing covers may expose you
to dangerous voltage or other
hazards. Refer all servicing to
qualified service personnel.
8
9
Before Using
IMPORTANT SAFETY INSTRUCTIONS (Continued)
Plug
configuration
Plug type
Australian
240 V
10 A
North American
240 V
15 A
Switzerland
240 V
6 A
Line voltage
EURO
UK
220 – 240 V
220 – 240 V
200 – 240 V
200 – 240 V
200 – 240 V
Plug
configuration
Plug type Line voltage
Use a 5 A fuse which is approved by
ASTA or BSI to BSI362.
Always replace the fuse cover after
changing the fuse.
p.42
POWER SUPPLY INFORMATION
22. Replacement Parts
When replacement parts are
required, be sure the service
technician has used replacement
parts specified by the manufacturer
or have the same characteristics
as the original part.
Unauthorized substitutions may
result in fire, electric shock, or
other hazards.
(Only the replacement of the lamp
should be made by users.)
23. Safety Check
Upon completion of any service
or repairs to this product, ask
the service technician to perform
safety checks to verify that the
product is in proper operating
condition.
24. Do not leave thermalpaper documents or easily
deformed items on top
of the unit or near the air
exhaust for long periods of
time.
The heat from the unit could erase
the information on the thermal
paper, or cause deformation or
warping.
25. Do not use the product
in a closed installation
location.
Do not place the product in a box
or in any other closed installation
location. Otherwise it may
overheat, which could result in a
risk of fire.
26. Do not look into the laser
light source of the remote
control or direct the laser
pointer toward a person or
a mirror.
The laser beam may cause
damage to the eyesight.
27. When using a wireless LAN
function:
• Do not use near people
with heart pacemakers.
• Do not use near electronic
medical equipment, or in
hospitals or other medical
institutions.
• Do not use inside aircraft
or in places where the
wireless LAN function
could interfere with
electromagnetic signals.
The electromagnetic interference
could cause a malfunction,
resulting in an accident.
28. If the use of a wireless
LAN function interferes
with another device’s
electromagnetic signals,
cease use immediately.
The electromagnetic interference
could cause a malfunction,
resulting in an accident.
If your line voltage is 220 to 240 V, use one of the following types of cable/plug.
IMPORTANT PRECAUTIONS
Moisture Condensation
Never operate this unit immediately after moving it from a cold location to a warm location.
When the unit is exposed to such a change in temperature, moisture may condense on the
lens and the crucial internal parts. Do not use the unit for at least 2 hours when there is an
extreme or sudden change in temperature to prevent the unit from possible damage.
Place and Manner of Installation
Do not place in hot locations, such as near heating equipment. Doing so could cause
•
malfunction, and shorten the life of the projector.
Avoid locations with oil or cigarette smoke. Doing so will dirty the optical parts, shortening
•
their lives, and darkening the screen.
Do not use this product in the upright position or tilt it up or down by more than 20° from
•
level. Doing so may cause a failure or shorten the life of the product.
Using this instrument near a TV or radio may cause interference to the images or audio
•
sound. If this happens, move it away from the TV or radio.
Moving the projector from a low-temperature room to a high-temperature room may cause
•
condensation on the lens or internal parts. If you continue to use it in that situation, it may
malfunction. Wait until the condensation naturally disappears.
In a high altitude location where air is thin, cooling efficiency is reduced so use the
•
projector with [Fan mode] set to [High].
Only plug the power cord into outlets rated for use with the power cord’s specified voltage
•
range. Do not overload extension cords or power strips as this can result in fire or electric
shock.
Route the power cable or the connecting cable away from where people could trip over it.
•
The projector may fall down, which could result in severe injury.
Be sure the power cord is easily reached for unplugging in case of emergency. Do not
•
place any obstacles near a wall outlet in which the cord is plugged.
10
11
Before Using
IMPORTANT PRECAUTIONS (Continued)
p.36
OTHER INFORMATION (Continued)
Avoid Volatile Liquid
Do not use volatile liquids, such as an insect spray, near the unit. Do not leave rubber or
plastic products touching the unit for a long time as they will leave marks on the finish.
Do not use a chemically saturated cloth.
EXEMPTION CLAUSES
•
Toshiba Corporation bears no responsibility in the case of damages arising from natural
disaster such as earthquakes, lightning, etc., fire not liable to Toshiba Corporation, acts
by third parties, other accidents, or use under abnormal conditions including erroneous or
improper operation and other problems.
•
Toshiba Corporation bears no responsibility for incidental damages (lost profit, work
interruption, corruption or loss of the memory contents, etc.) arising from the use of or the
inability to use this unit.
•
Toshiba Corporation accepts no liability whatsoever for any damages arising from not
having followed the descriptions in this Owner’s Manual.
Toshiba Corporation accepts no liability whatsoever for any damages arising from
•
malfunctions arising from combination with equipment or software that is not related to
Toshiba Corporation.
Toshiba bears no responsibility for information being intercepted or leaked due to the use
•
of a wireless LAN, or any damages therefore.
OTHER INFORMATION
Copyrights
Showing or transmitting commercial imaging software or broadcast or cable-broad casting
programs with the purpose of other than the personal and private viewing, including
modifying images using the freeze or resize functions, or displaying with the varying
aspect ratio of the images, could violate the direct or indirect copyrights of the imaging
software or broadcast program, etc., if done without first consulting with the copyright
holder. For this reason, please take appropriate measures before performing one of the
actions listed above, including obtaining a license from the copyright holder.
Disposal
This product contains substances which are harmful to humans and the environment.
The lamp contains mercury.
•
Please dispose of this product or used lamps in accordance with local regulations.
Following information is only for EU-member states:
The use of the symbol indicates that this product may not be treated as
household waste. By ensuring this product is disposed of correctly, you will
help prevent potential negative consequences for the environment and human
health, which could otherwise be caused by inappropriate waste handling of
this product. For more detailed information about recycling of this product,
please contact your local city office, your household waste disposal service or
the shop where you purchased the product.
Trademarks
VGA, SVGA, XGA, SXGA, UXGA are trademarks or registered trademarks of
•
International Business Machines Corporation.
DLP (Digital Light Processing) is a registered trademark of Texas Instruments, Inc.
•
Macintosh is a registered trademark of Apple Computer, Inc.
•
Windows is a registered trademark of Microsoft Corporation in the U.S. and other
•
countries.
Adobe and Acrobat Reader are registered trademarks of Adobe Systems Incorporated.
•
Contains technology by Ingenient Technologies, Inc.
•
Copyright
All other brand and product names are trademarks or registered trademarks of their
•
respective companies.
Notational Conventions Used in This Manual
References to pages with related information are annotated as follows.
•
For example, if making a reference to page 36:
The illustrations in this document are for reference purposes only and may not reflect
•
your package exactly.
REMOTE CONTROL BATTERIES
Warning
Never throw batteries into a fire.
•
Using the batteries improperly may cause them to explode or leak and may result in serious
injury.
If battery-leaking fluid contacts skin, wash the fluid off immediately with clean water and
consult a doctor. If the fluid spills on an instrument, avoid contact and wipe it off using
tissue paper. Then dispose of the used tissue paper as flammable garbage after moistening
with water.
Notes
Be sure to use AAA (LR03) size batteries.
•
Dispose of batteries in a designated disposal area.
•
Attention should be drawn to the environmental aspects of battery disposal.
•
Do not mix different battery types or combine used batteries with new ones.
•
If the remote control does not operate correctly, or if the operating range becomes
•
reduced, replace both batteries with new ones.
If the batteries are dead or if you will not be using the remote control for a long time,
•
remove the batteries to prevent battery acid from leaking into the battery compartment.
2000-2006 Ingenient Technologies, Inc. All rights reserved.
©
12
13
Before Using
CONTENTS
Before Using
SAFETY PRECAUTIONS ............................................................................... 2
IMPORTANT SAFETY INSTRUCTIONS ......................................................... 4
POWER SUPPLY INFORMATION .................................................................. 9
IMPORTANT PRECAUTIONS ......................................................................... 9
EXEMPTION CLAUSES ................................................................................. 10
OTHER INFORMATION .................................................................................. 10
REMOTE CONTROL BATTERIES .................................................................. 11
CONTENTS .................................................................................................... 12
Preparations
Checking the package contents ...................................................................... 14
Names of each part on the main unit .............................................................. 15
Names of each part on the control panel and remote control ......................... 16
Label location .................................................................................................. 17
Names of the terminals on the rear panel ....................................................... 18
Preparing and using the remote control .......................................................... 19
Operating a computer using the remote control .............................................. 20
Placement ....................................................................................................... 21
Connection ...................................................................................................... 22
Operations
Turning the power on and off ........................................................................... 24
Basic operations .............................................................................................. 26
Using handy features ...................................................................................... 29
Using auto setting (For computer input only) ............................................... 29
Correcting the keystone distortion ............................................................... 29
Zooming out the images .............................................................................. 30
Resizing image ............................................................................................ 31
Cutting off the picture and sound temporarily (Mute) ................................... 32
Changing picture mode ................................................................................ 32
Changing screen size .................................................................................. 32
Freezing the image (Freeze) ........................................................................ 33
Setting the password ................................................................................... 33
Using the menus 1 .......................................................................................... 35
Setup using the Setting display .................................................................... 35
The image adjustment menu ....................................................................... 36
The position adjustment menu ..................................................................... 37
The display setting menu ............................................................................. 38
The Default setting menu ............................................................................. 41
Displaying Information (Status display) ........................................................ 43
Using the menus 2 ..........................................................................................
Checking the projector status .......................................................................... 58
Using the Network Projector ........................................................................... 59
Installing the applications ................................................................................ 60
Using the Network Utility ................................................................................. 62
Projecting images stored in a USB memory ................................................... 78
How to use the JPEG Conversion Tool............................................................ 81
Setting up the projector using a Web browser ................................................. 85
Maintenance
About lamp ...................................................................................................... 88
Lamp replacement .......................................................................................... 89
Lens and main unit cleaning ........................................................................... 92
Others
Trouble indications ........................................................................................... 93
Troubleshooting ............................................................................................... 94
Specifications .................................................................................................. 96
48
Setup using the Setting display (2) ..............................................................
Setting up the Network Projector/Network Utility ......................................... 49
Computer settings ........................................................................................ 54
The control setting menu ............................................................................. 55
Setting slideshow options ............................................................................ 56
Status display ............................................................................................... 58
Displaying a computer’s screen via the projector ......................................... 62
Displaying a JPEG image saved on a computer via the projector ............... 64
Displaying a video file saved on a computer via the projector ..................... 65
Displaying computer’s screens via projectors using Multiscreen function ... 68
Easy Connect utility ..................................................................................... 73
Operating the projector ................................................................................ 77
Playing a slide show from a thumbnail list ................................................... 78
Launching the JPEG Conversion Tool ......................................................... 81
Converting files created with Microsoft® PowerPoint® .................................. 82
Making a presentation with converted JPEG files........................................ 83
Creating a screen capture and converting it into a JPEG file ...................... 84
48
Network and USB memory
Before connecting via network ........................................................................ 44
Communication mode .................................................................................. 45
How to use the USB terminal .......................................................................... 46
Preparations
■
■
■
■
■
■
■
■
Checking the package contents
Please make sure that the following items are included in the box, along with the main unit.
If any item is missing, immediately contact the store where you purchased the product.
(1) (4) (7)
(2) (5)
(3) (6) (8)
(1) Remote control
■
(2) LR03 (SIZE AAA) batteries for remote control (2)
■
(3) CD-ROM
■
(4)
Owner’s Manual
■
Notes
1: To maintain original performance, always use the supplied cables.
2: The shape and number of supplied power cords vary depending on the product destination.
(5)
RGB cable (3 m)
■
(6)
Power cord
■
(7)
Carrying bag
■
(8)
Mouse remote control receiver
■
Save Original Packing Materials
The original shipping carton and packing materials will come in handy if you ever have to
ship your projector. For maximum protection when shipping your projector, repack the set
as it was originally packed at the factory.
The Supplied CD-ROM
◆
The supplied CD-ROM contains an owner’s manual, including information not available for
the printed Owner’s manual (Getting started), each Application, Project Management Utility
Manual and Quick Reference in PDF format. (PDF: Portable Document Format) Please
use Acrobat Reader 5 or later version view the manual.
Adobe
■
The supplied CD-ROM does not contain Acrobat® Reader®. If you cannot read PDF
fi les, please install Acrobat Reader software in your computer by downloading it from
the Adobe Systems website.
Viewing the manual
■
Run the CD-ROM and double-click on Start.pdf. Acrobat® Reader® launches, and a screen
appears asking you that “Select your model”, then click on the model name that you are
using. After you select [Owner’s manual] on the next screen, click on the desired language.
The Owner’s Manual cover and list of bookmarks appear. Click on a bookmark title to view
that section of the manual. Click on
See the Help menu for more information about Acrobat
®
Acrobat® Reader® or Adobe® Reader
p.
to view a reference page with related information.
®
®
Reader®.
[Note 1]
[Note 1, 2]
Names of each part on the main unit
(10)(11)(
Back Front
Name : Function
(1) Air exhaust : Expels air that has grown hot inside the projector.
(2) Lamp cover :
(3) Control panel :
(4) Zooming ring :
(5) Focusing ring :
(6) Lens : Projects expanded image.
(7) Lens cap :
(8) Infrared remote sensor :
(9) AC IN socket : Connect the supplied power cord here.
(
10
) Main power switch : AC power line ON (standby)/OFF.
11)Terminals on the rear panel
(
(12) Speaker : Outputs audio sound.
13
) Antitheft lock slot : Attach a safety cable or any other antitheft device.
(
(
14
) Air intake : Draws in air from outside the projector for internal cool
(
15
) Tilt adjuster :
(16) Handle : Hold to carry the projector by pulling out.
(
17)Foot adjuster release button
(18) Foot adjuster :
Remove to replace lamp.
Operates the projector.
Adjusts screen size.
Adjusts screen focus.
Replace the cap when not using the projector to protect
the lens.
Senses commands from the remote control.
:
Connects external devices.
down.
Adjusts the projector’s horizontal tilt.
:
Press to set up or stow the foot adjuster.
Adjusts the vertical projection angle.
p.16
p.27
p.27
(17)(16)(15)(
p.90
p.18
18
p.27
p.27
15
)(14)(13)(12)(9)
)
p.19
p.27
(8)(4)(3) (7)(6)(5)(2)(1)
Preparations
14 15
Names of each part on the control panel and remote control
Remote ControlControl panel
(11) (12) (13)
(10)
(9)
(8)
(7)
CAUTION
Do not look into the laser light
•
source of the remote control
(14)
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(16)
(15)
(23)
(9)
(10)
(1)
(19)
(20)
or direct the laser pointer
toward a person or a mirror.
•
Handling and adjusting
other than described in
this manual may lead to
dangerous exposure to laser.
Name : Main Function
Control panel
(1) ENTER button : Accepts the selected mode.
(2) MENU button :
Displays menus.
(3) ZOOM – button : Adjusts the screen size.
(4) AUTO SET button :
(5) ON/STANDBY button :
(6) NETWORK button :
(7) INPUT button :
(8) KEYSTONE button :
Performs auto-adjustment of input signals from computer.
Turns the power on/off (standby).
Switches to network input mode.
Selects input.
Adjusts keystone distortion.
(9) RETURN button : Goes back one screen.
(
10
) Selection button :
(11) LAMP indicator :
(12) ON/STANDBY indicator :
(13) TEMP indicator :
Menu selections and adjustments, volume control, etc.
Displays lamp mode.
Displays whether power is on or off (standby).
Lights when internal temperature is too high.
(14) ZOOM + button : Adjusts the screen size.
p.35
p.26
p.93
Remote control
(1) ENTER button : Accepts the selected mode.
(2) MENU button :
(3) KEYSTONE button :
(4) ON/STANDBY button :
(5) AUTO SET button :
Displays menus.
Adjusts keystone distortion.
Turns the power on/off (standby).
Performs auto-adjustment of input signals from computer.
(6) ZOOM button : Adjusts the screen size.
(7) INPUT button :
(8) NETWORK button :
Selects input.
Switches to network input mode.
p.35
p.26
16 17
Remote control transmitter
Laser light source
(12)
(4)
(5)
(3)
(22)
(24)
(11)
(13)
(14)
(2)
Battery
cover
(6)
(21)
(17)
Caution
label
(18)
p.24
p.48
p.29
p.24
p.93
p.29
p.24
p.48
(25)
p.29
p.35
p.29
Name : Main Function
(9) RETURN button : Goes back one screen.
10
) Selection button :
(
Menu selections and adjustments, volume control, etc.
(11) LASER button : Shows a laser pointer.
(
12
) Laser indicator : Lights when laser is on.
(
13
) Mouse control button :
(14) PAGE+ button :
(15) MUTE button :
(16) FREEZE button :
Controls a mouse pointer.
Proceeds PowerPoint
Cuts off the picture and sound temporarily.
Pauses image.
p.33
p.20 p.63 p.69
®
slides.
p.20 p.63 p.69
p.32
(17) Ten-Key button : Use as a ten-key pad with wireless LAN, from which
numbers and characters can be entered.
(18)
Remote control code switch:Sets the code of remote control to that of the projector.
(19) PICTURE button : Changes image mode.
(20) SCREEN SIZE button : Changes screen size.
p.32
p.32
(21) GUIDE button : Displays operation guide for slideshow.
(22) RESIZE button
: Enlarges image.
(23) PAGE- button : Goes back PowerPoint® slides.
p.31
p.20 p.63 p.69
(24) R-CLICK button : Functions as right-click of a mouse.
(25) L-CLICK button : Functions as left-click of a mouse.
p.50
p.80
p.20 p.63 p.69
p.20 p.63 p.69
Note
For the remainder of this manual, buttons are referred to as follows:
•
Selection buttons
; ENTER button ⇒
⇒
Label location
Caution – use of controls or adjustments or performance of procedures other than
those specifi ed herein may result in hazardous radiation exposure.
p.35
p.42
Preparations
Names of the terminals on the rear panel
Preparing and using the remote control
(1) (2)
(7)
(6)
Name : Main Function
(1) LAN terminal : Connects a network cable.
(2) USB terminal :
(3)
COMPUTER (Y/PB/PR) 2 IN terminal
(4) COMPUTER (Y/P
(5) VIDEO terminal : Input video signals from video equipment.
(6) AC IN socket :
(7) CONTROL terminal :
(8) Main power switch : AC power line ON (standby)/OFF.
(9) MONITOR terminal : Connect to a computer display, etc.
(
10
) AUDIO OUT terminal : Outputs audio signals.
(
11
) AUDIO (L/R) terminal : Input audio signals from video equipment. (Dual use for
12
) S-VIDEO terminal : Input S video signals from video equipment.
(
(9) (10)
Connects a commercial USB memory.
: Input analog RGB signal from a computer or other
source, or a component video signal (
equipment.
AUDIO IN: Input audio signals.
) 1 IN terminal
B/PR
AUDIO IN: Input audio signals.
: Input analog or digital RGB signal from a computer, or a
component video signal (Y/P
Connects the supplied power cord here.
When operating the projector via a computer, connect this
to the controlling computer’s RS-232C port.
VIDEO and S-VIDEO)
(4)(3)
(5)
(12)(11)(8)
p.46
Y/PB/PR) from video
) from video equipment.
B/PR
p.100
Loading dry-cell batteries
■
into the remote control
1
Remove the battery cover.
Operating the remote
■
control
Point toward the projector’s infrared
remote sensor, and press any button
on the remote control.
Operating the projector from the front
•
2
Insert the dry-cell batteries.
Be sure to align the plus and minus ends
of the batteries properly.
Two batteries (LR03, SIZE AAA) are used.
3
Replace the battery cover.
When operating the remote control
from behind the projector, infrared
signal is refl ected on the projecting
surface and may travel a shorter
distance to reach the projector
depending on the shape and material
of the projecting surface.
Approx.15°
Approx.5m
Dry-cell batteries
•
Before using the batteries, be sure to observe the Safety Precautions described in
previous pages.
•
Remove batteries from remote control when not using for extended periods.
•
If the remote control stops working, or if its range decreases, replace all the batteries
with new ones.
•
Keep the batteries away from the reach of children.
Batteries are choking hazards and can be very dangerous if swallowed. If the batteries
are swallowed, seek medical assistance immediately.
The remote control
•
The remote control may fail to operate if the infrared remote sensor is exposed to bright
sunlight or fl uorescent lighting.
•
Do not drop or bang.
•
Do not leave in hot or humid locations.
•
Do not allow it to get wet or place it on top of wet objects.
•
Do not take apart.
•
In rare cases, ambient conditions could impede the operation of the remote control. If
this happens, point the remote control at the main unit again, and repeat the operation.
Preparations
18 19
20
21
Preparations
Operating a computer using the remote control
1
Mouse remote control receiver
To USB port
2
Mouse control
Remote Control Front Remote Control Rear
PAGE –
PAGE +
R-CLICK
L-CLICK
p.42
90°
90°
a
Placement
A computer can be operated using the projector’s remote control. This function is available on
any computer with the Windows® 98/98SE, Windows® Me, Windows® 2000, Windows® XP, or
Windows Vista® OS, that is equipped with a USB port which can support USB1.1 (The mouse
remote control receiver is also supported on OS 9 or OS X for the Macintosh). However,
please note that Toshiba does not guarantee the operation of all computers.
Connecting a computer
Connect the mouse remote control receiver (supplied) to a computer.
The remote control may fail to operate
if the mouse remote control receiver
is exposed to bright sunlight or
fluorescent lighting.
In such a case, change position or
direction of the mouse remote control
receiver and retry.
Operating a computer
Operate remote control’s buttons towards the mouse remote control receiver.
Moving the mouse pointer
Press the mouse control button in the direction you wish the mouse pointer to move,
then press.
To left click
Press the L-CLICK button.
To right click
Press the R-CLICK button.
To drag and drop
Holding down the L-CLICK button, move the mouse control button until the mouse
pointer is over the desired location, then release the L-CLICK button.
Using the computer’s page up [#] and down [$] function
Press the PAGE+ and PAGE- buttons to switch PowerPoint® slides.
Placement Styles
As shown in the figures below, this device can be placed in 4 different styles.
The factory setting is “floor-mounted front projection.” Set the [Projection mode] in the
Default setting 2 menu
Floor-mounted front projection
Ceiling-mounted front projection
WARNING
Always obey the instructions listed in IMPORTANT SAFETY INSTRUCTIONS
•
when placing the unit. Attempting to clean and replace the lamp in a high location
by yourself may cause you to fall, resulting in injury.
If you wish to mount the projector on the ceiling, be sure to ask your dealer
•
to do so. Mounting the projector on a ceiling requires special ceiling brackets (sold
separately) and specialized knowledge. Improper mounting could cause the projector
to fall, resulting in an accident.
If the projector is ceiling-mounted, install the breaker for turning off the power in
•
case of anomaly. Let everyone involved with the use of the projector know that fact.
Projection Distance and Size
Use the figures, tables, and formulas below to determine the projection size and projection distance.
(Projection sizes are approximate values for full-size picture with no keystone adjustment.)
Screen
a is the distance (m, feet) between the lens and the screen, and
corresponds to a range of 1.29 m (4.23 ft.) to 12.01 m (39.40 ft.).
The lens center is in the same level with an image bottom.
, in accordance with your needs.
As seen from above
As seen from the side
Lens center
Floor-mounted rear projection
Ceiling-mounted rear projection
a (min length) = 0.0335 x Projection size (inches) - 0.05
a (max length) = 0.0402 x Projection size (inches) - 0.0488
Projection size
40 inches 1.29 m (4.23 ft.) 1.56 m (5.12 ft.)
60 inches 1.96 m (6.43 ft.) 2.36 m (7.74 ft.)
80 inches 2.63 m (8.63 ft.) 3.17 m (10.40 ft.)
100 inches 3.30 m (10.83 ft.) 3.97 m (13.02 ft.)
150 inches 4.98 m (16.34 ft.) 5.98 m (19.62 ft.)
200 inches 6.65 m (21.82 ft.) 7.99 m (26.21 ft.)
250 inches 8.33 m (27.33 ft.) 10.00 m (32.81 ft.)
300 inches 10.00 m (32.81 ft.) 12.01 m (39.40 ft.)
Projection distance a
min length
(zooming max)
max length
(zooming min)
Connection
Before connection
•
Read the owner’s manual of the device you are connecting to the projector.
•
Some computers cannot be used with or connected to this projector.
Check for an RGB output terminal, supported signal
•
Turn off the power of both devices before connecting.
•
The fi gures below show sample connections. This does not mean that all of these devices
can or must be connected simultaneously.
Connecting with computers
Computer
To RGB output
RGB cable
(supplied)
To audio
output
Audio cable
(not supplied)
p.97
To DVI output
DVI cable
(not supplied)
, etc.
Computer
To audio output
Audio cable
(not supplied)
Connecting with AV equipments
DVD video recorder,
DVD player, etc.
To Y/CB/C
R
Conversion adapter
BNC-pin (not supplied)
Monitor cable
Mini D-sub
15P-BNC
(not supplied)
outputGreen
(Y)/Blue
(C
)/Red (CR)
B
To audio
output
White (L)/
Red (R)
Audio cable
(not supplied)
To DVI output
DVI cable
29-pin
(not supplied)
DVD video recorder, etc.
To HDMI output
Conversion
adapter
HDMI-DVI
(not supplied)
To audio
output
White (L)/
Red (R)
Audio cable
(not supplied)
Preparations
Audio cable
(not supplied)
To audio input
Speaker with built-in amplifi er
To RS-232C
terminal
Computer
(for control)
Control cable
(not supplied)
RGB cable
(not supplied)
Monitor
Notes
•
The MONITOR OUT terminal outputs analog RGB signals from the COMPUTER 1 IN
terminal or the COMPUTER 2 IN terminal, or outputs Y/P
B/PR signals as selected with the
INPUT button. If no input is selected, the MONITOR OUT terminal outputs the input signals
last selected for each input terminal. (Digital RGB signals will not be output.)
•
Signals are output from MONITOR OUT terminal even in standby mode.
However, from AUDIO OUT terminal, no audio signal is output.
•
A computer monitor cannot accept Y/P
B/PR signals correctly.
22 23
Audio cable
(not supplied)
To audio input
White (L)/ Red (R)
Audio amplifier, etc.
AV cable
(not supplied)
To audio output
White (L)/ Red (R)
To video output
(yellow)
Video recorder, etc.
S-video cable
(not supplied)
To S-video
output
Notes
•
The AUDIO (L/R) terminal doubles for devices connected to S-VIDEO terminal and VIDEO
terminal.
•
When an AUDIO OUT terminal is connected, sound is not output from the projector
speaker.
•
Output volume of AUDIO OUT terminal can be adjusted by the VOL button.
24
25
Operations
1
2
1
2
Operations
p.38
p.26
p.41
p.43
p.33
1
2
3
4
Turning the power on and off
Connecting the power cord
Insert the power cord connector
into the AC IN socket of the
projector.
Insert the power cord plug into a
wall or other power outlet.
Removing the lens cap
Be sure to remove the lens cap when the power is turned on. If the cap is left on the
projector, it could become deformed due to heat.
Turning the power on
Power cord connector
(Supplied)
Turn on the main power switch.
The ON/STANDBY indicator will change to orange,
indicating standby mode.
Control panel
Press the ON/STANDBY button.
The power turns on with a beep sound (if the beep
sound is set to [On]), and the ON/STANDBY indicator
lights green. After a moment, the start-up screen
appears.
CAUTION
Do not look into the lens while the lamp is on. The strong light from the lamp may cause
•
damage to your eyesight.
Do not block the air intake or exhaust. Doing so could cause a fire due to internal overheating.
•
Do not place your hands, face, or other objects near the air exhaust, the lamp cover or
•
the bottom of the unit. Doing so could result in injury and/or damage the object.
Remote
control
Notes
•
The start-up screen will disappear after a moment. You can dismiss the start-up screen
before this by performing any operation. You can also configure the system to prevent
the start-up screen from appearing. To do this, use the Display setting menu
•
The first time you use the projector after purchase, after the start-up screen disappears,
the start menu is displayed
•
You can disable the beep sound in the Default setting 1 menu
•
When [Key lock] is [On], the operation buttons of the projector do not work
•
When [Password] is [On], enter password then the start-up screen is displayed after the
Password entry screen disappears
•
Do not touch the lens directly with your hand.
If fingerprints or stains are left on the projection lens surface, they may interfere with the
projector’s ability to project images on the screen.
Turning the power off
Press the ON/STANDBY button.
When the setting of beep sound is
on the screen
press the ON/STANDBY button again. If you do not wish to shut off the power, wait for a
while without conducting any operations. This message will disappear after a moment.
(This operation is no longer valid after the message disappears.)
Press the ON/STANDBY button again.
When the setting of beep sound is [On], the projector beeps, and the screen
disappears, but the internal cooling fan continues to operate. Then, the projector goes
into standby mode.
During cooling, the ON/STANDBY indicator flashes. While the
indicator is flashing, the power can not be turned back on. There is
no problem with unplugging the power cord in this state.
Turn off the main power switch.
Replace the lens cap.
After use, replace the lens cap.
Note
The projector consumes about 11 W of power in
•
standby. We recommend that you unplug the power cord
if you will not be using the projector for an extended
period.
Precautions
When you wish to restart the projector again right after turning off the power, give the
•
lamp time (about 5 minutes) to cool before plugging it back in. If the lamp overheats, it
may fail to light.
Right after turning off the power, the unit may become very hot, especially air exhaust,
•
lamp cover or the bottom of the unit. Please handle with care to avoid burn injuries.
.
.
.
.
.
[On], the projector beeps, and a message appears
, confirming that you wish to shut off the power. To shut off the power,
Basic operations
Turn on the power.
1
Turn on the power by following the instructions in “Turning the power on”
Select the language and the lamp power (When using the
2
p.24
fi rst time).
When the projector is used for the fi rst time after purchase, the start menu for language
(to display the menus and messages on the screen) and lamp power selection and
confi guration is displayed in English. (If the screen is out of focus, adjust it according to
the step 6.)
1
Use the
press the
Message for setup confi rmation is displayed in a selected language.
Then, the menu for lamp power selection and confi guration is displayed. It is
automatically set as Standard. To change the setting, follow the step
2
Use the
button.
The lamp power, if selected, will be toggled without pressing the
automatically disappears in a few seconds.
Notes
When the projector is turned on the next time, the start menu does not appear upon
•
startup. However, if [Reset all] is executed from the Default setting 2 menu
the start menu will be displayed the next time when the power is turned on.
•
The language can also be set via the Display setting menu
via the Default setting 2 menu
•
This owner’s manual assumes that English has been selected.
,
,
or
button.
English
French
German
Italian
Spanish
Portuguese
Russian
Swedish
Turkish
or button to select the lamp power and press the
button to select the desired language and
Polish
Norwegian
Finnish
Czech
Hungarian
Greek
Danish
Dutch
Rumanian
button. The display
p.38
and Lamp power
p.42
.
Japanese
Chinese (simplified)
Chinese (traditional)
Korean
Indonesian
2
.
.
p.42
Notes
When [Auto input search] is set to [Off] in the Default setting 1 menu
•
(factory setting is [On]), the Input select menu appears if you press the INPUT
button.
If no signal is being output from the connected equipment, pressing the INPUT
•
button does not change the input and “There is no other input signal.” message
will appear.
Projector placement angle adjustments
5
The placement angle and the height of the projected image can be adjusted by the
foot adjuster.
1
Lift up the front of the projector to
p.41
the desired angle, then press the foot
adjuster release button.
The foot adjuster extends. Release the button
to lock the position.
2
To fi ne adjust the angle, twist the foot
adjuster.
3
To adjust the horizontal angle, use the
right and left tilt adjusters.
•
To stow the foot adjuster, hold up the projector while pressing the foot adjuster
release button, then slowly lower the projector.
Operations
Note
•
,
When [Auto keystone] is set to [On] in the Default setting 1 menu, the keystone
distortion will automatically be corrected based on the projector placement angle. If
you do not desire the automatic keystone correction, set [Auto keystone] to [Off].
Adjusting the screen size and focus
6
1
Use the zooming ring to adjust the
screen size.
2
Use the focusing ring to adjust the
Zooming ring
1
Focusing ring
2
focus.
Activate the connected device.
3
Turn on and start the connected device such as a computer.
Press the INPUT button.
4
An image of the connected equipment is projected.
Each time you press the INPUT button, it switches to the input of the connected
equipment that is outputting video signals.
26 27
Adjusting the volume with the
7
buttons
The speaker volume can be adjusted when an audio signal is being input.
Basic operations (Continued)
Precautions
•
Lamp characteristics may rarely cause the brightness to fl uctuate slightly.
•
The DLP® chip is made using extremely advanced technology. There may be black spots
(pixels that do not light) or bright spots (pixels that are constantly lit) on the panel. These
are intrinsic characteristics of the technology and are not malfunctions.
Notes
A lamp is consumable item. If used for extended periods, images will appear dark, and
•
the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The
lifetime of the lamp depends on conditions of use.)
Although this projector supports a wide range of RGB signals
•
supported by this projector (XGA) will be expanded or shrunk, which will affect image
quality slightly. To view high-quality images, set the computer’s external output to XGA.
With some models of computer having LCD displays or the like, displaying images
•
simultaneously on the projector and the monitor’s display may prevent the images from
displaying properly. If this happens, turn off the computer’s LCD display. For information
on how to turn off the LCD display, see the computer’s owner’s manual.
If no signal is being input from the connected equipment or signal input is stopped while
•
projecting, the “No signal” message will appear.
If a signal not supported by the projector is input, the “Unsupported signal” message
•
will appear.
If an unavailable operation button is pressed, the
•
(if the beep sound is set to [On]).
Moving pictures played back on computers using DVD software may appear unnatural
•
when projected with this projector. However, it is not a malfunction of the projector.
icon will appear with a beep sound
28 29
p.97
, any resolutions not
Using handy features
Using auto setting (For computer input only)
■
This function automatically sets up the projector to the optimum state. It
sets up sampling phase, frequency and screen position, for each type
of the input signal by using simple operations.
Press the remote control’s AUTO SET button.
The icon will appear during processing.
Notes
The image may not be projected or auto adjustment/setting may
•
not be performed correctly for input signals other than those
supported by the projector
If auto setting fails adjustment, adjust manually with the Position adjustment
•
p.37
menu
Correcting the keystone distortion
■
When the projector placement angle against the screen is changed while projecting the
image, the picture will undergo keystone (trapezoidal) distortion.
This projector is capable of correcting this keystone distortion.
•
The keystone distortion will be corrected automatically based on the projector’s
placement angle.
.
Before correction
p.97, p.98
Adjusting Keystone distortion [Manual]
Press the KEYSTONE button.
1
Use the buttons for keystone
2
.
After correction
Control panel
adjustment.
Notes
•
Depending on the amount of keystone adjustment
and the content of images, some information may
be lost, or the picture quality may suffer.
Even if [Auto keystone] is set to [On], keystone distortion can be adjusted
•
manually. Note that if you change the position or angle of the projector, automatic
keystone correction will be performed again.
When [Auto keystone] is set to [On], the automatic keystone correction will be
•
performed each time the power is turned on.
The keystone correction settings are memorized after the power has been turned off.
•
Therefore, it is recommended that you set [Auto keystone] to [Off], if the case is that
the projector placement angle against the screen remains unchanged and you do not
wish to change the keystone adjustment that you set.
Some adjustments using both digital zoom and keystone correction while displaying
•
an input image with a 16:9 aspect ratio, may affect displaying the menu properly. In
such a case, reset either digital zoom or keystone correction to use the menu.
Remote
control
Remote
control
Operations
30
31
Operations
1
2
Using handy features (Continued)
1
2
3
4
Zooming out the images
This projector is provided with the digital zoom (electric zoom: 100 - 62%) in addition
to the optical zoom (manual adjustment with zooming ring). (Note that the display, if
digitally zoomed out, may suffer from some degradation.)
Press the ZOOM – button.
Each time the ZOOM – button is pressed, the
image is reduced in size.
Control panel
Press ZOOM + button to bring it back
to the original size.
Each time the ZOOM + button is pressed, the
image size increases.
(You cannot make it larger than the original
size.)
Notes
Pressing either ZOOM – or ZOOM + button will display an adjustment bar.
•
The adjustment value will automatically be saved.
•
Remote
control
Resizing image
The projected image can be resized (zoomed in/out).
Press the remote control’s RESIZE button.
Each time you press the RESIZE button, zoom ratio is up. You can keep
pressing.
To zoom out, press the remote control’s RESIZE
button.
Each time you press the RESIZE button, zoom ratio is
down. You can keep pressing.
(However, the image cannot be smaller than the original
size.)
To move the area to zoom in, use the
Remote
control
buttons.
You can keep pressing.
When the image returns to the original size by pressing RESIZE
button several times, the zoom will be reset.
Pressing the RETURN button during resizing also resets the zoom.
Notes
The icon appears while resizing.
•
•
Operating a function other than Mute will release resizing.
•
As zooming is processed digitally, the image quality is degraded in larger zoom
ratio.
•
During resizing or moving the zooming area, the image may be distorted.
Loading...