现货库存、技术资料、百科信息、热点资讯，精彩尽在鼎好!
TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic
TC7WG00FU,TC7WG00FK
Dual 2-Input NAND Gate
Features
TC7WG00FU/FK
• High-level output current: IOH/IOL = ±8 mA (min)
at V
• High-speed operation: t
= 2.5 ns (typ.)
pd
at V
= 3 V
CC
= 3.3 V,15pF
CC
• Operating voltage range: VCC = 0.9~3.6 V
• 5.5-V tolerant inputs
• 3.6-V power down protection outputs
Marking
Absolute Maximum Ratings
SM8 US8
Product name
G 00
Lot No.
WG
00
(Ta = 25°C)
TC7WG00FU
TC7WG00FK
Weight
SSOP8-P-0.65 : 0.02 g (typ.)
SSOP8-P-0.50A : 0.01 g (typ.)
Pin Assignment (top view)
Characteristics Symbol Value Unit
Power supply voltage V
DC input voltage V
DC output voltage V
Input diode current I
Output diode current I
DC output current I
DC V
Power dissipation
Storage temperature T
/ ground current I
CC
CC
IN
OUT
IK
OK
OUT
CC
P
D
−65~150 °C
stg
−0.5~4.6 V
−0.5~7.0 V
−0.5~4.6 (Note 1)
−0.5~VCC + 0.5 (Note 2)
−20 mA
−20 (Note 3) mA
±25 mA
±50 mA
300 (SM8)
200 (US8)
mW
V
1A
1B
2Y
GND
1
2
3
4
Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the
significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if
the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum
ratings and the operating ranges.
Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook
(“Handling Precautions”/Derating Concept and Methods) and individual reliability data (i.e. reliability test report
and estimated failure rate, etc).
Note 1: V
Note 2: High or Low State. I
Note 3: V
CC
OUT
= 0V
< GND
absolute maximum rating must be observed.
OUT
1
2007-11-01
V
8
CC
1Y
7
2B
6
2A
5
IEC Logic Symbol Truth Table
TC7WG00FU/FK
1A
1B
2A
2B
&
1Y
2Y
Inputs Outputs
A B Y
L L H
L H H
H L H
H H L
Operating Ranges
Characteristics Symbol Value Unit
Power supply voltage V
Input voltage VIN 0~5.5 V
Output voltage V
Output Current IOH/IOL
Operating temperature T
Input rise and fall time dt/dV 0~10 (Note 12) ns/V
CC
OUT
opr
0.9~3.6 V
0~3.6 (Note 4)
0~V
±8.0 (Note 6)
±4.0 (Note 7)
±3.0 (Note 8)
±1.7 (Note 9)
±0.3 (Note 10)
±0.02 (Note 11)
−40~85 °C
(Note 5)
CC
V
mA
Note 4: VCC = 0V
Note 5: High or Low state.
Note 6: VCC = 3.0~3.6 V
Note 7: VCC = 2.3~2.7 V
Note 8: V
Note 9: V
= 1.65~1.95 V
CC
= 1.4~1.6 V
CC
Note 10: VCC = 1.1~1.3 V
Note 11: VCC = 0.9 V
Note 12: VIN = 0.8~2.0 V, VCC = 3.0 V
2
2007-11-01
Electrical Characteristics
DC Characteristics
TC7WG00FU/FK
Characteristics Symbol Test Condition
High level VIH ⎯
Input voltage
Low level V
⎯
IL
High level VOH
Output voltage
Low level V
V
OL
Input leakage current IIN V
Power off leakage current I
OFF
Quiescent supply current ICC V
Ta = 25°C Ta = −40~85°C
(V) Min Typ. Max Min Max
V
CC
0.9 V
1.1~1.3
1.4~1.6
1.65~
1.95
V
× 0.7
V
× 0.65
V
× 0.65
⎯ ⎯ VCC ⎯
CC
CC
⎯ ⎯
CC
⎯ ⎯
CC
⎯ ⎯
V
CC
× 0.7
V
CC
× 0.65
V
CC
× 0.65
⎯
⎯
⎯
2.3~2.7 1.7 ⎯ ⎯ 1.7 ⎯
3.0~3.6 2.0 ⎯ ⎯ 2.0 ⎯
0.9 ⎯ ⎯ GND ⎯ GND
1.1~1.3 ⎯ ⎯
1.4~1.6 ⎯ ⎯
1.65~
1.95
⎯ ⎯
CC
× 0.3
V
CC
× 0.35
VCC
× 0.35
⎯
⎯
⎯
V
CC
× 0.3
V
CC
× 0.35
V
CC
× 0.35
V
2.3~2.7 ⎯ ⎯ 0.7 ⎯ 0.7
3.0~3.6 ⎯ ⎯ 0.8 ⎯ 0.8
IOH =−0.02 mA 0.9 0.75 ⎯ ⎯ 0.75 ⎯
V
CC
CC
CC
⎯ ⎯
⎯ ⎯
⎯ ⎯
IOH = −0.3 mA 1.1~1.3
V
IN
IOH = −1.7 mA 1.4~1.6
= V
IH
VIL
or
IOH = −3.0 mA
1.65~
1.95
× 0.75
V
× 0.75
V
-0.45
V
CC
× 0.75
V
CC
× 0.75
V
CC
-0.45
⎯
⎯
⎯
IOH = −4.0 mA 2.3~2.7 2.0 ⎯ ⎯ 2.0 ⎯
I
= −8.0 mA 3.0~3.6 2.48 ⎯ ⎯ 2.48 ⎯
OH
IOL = 0.02 mA 0.9 ⎯ ⎯ 0.1 ⎯ 0.1
V
IN
IOL = 0.3 mA 1.1~1.3 ⎯ ⎯
IOL = 1.7 mA 1.4~1.6 ⎯ ⎯
= V
IH
IOL = 3.0 mA
1.65~
1.95
CC
× 0.25
V
CC
× 0.25
⎯ ⎯ 0.45 ⎯ 0.45
⎯
⎯
V
CC
× 0.25
V
CC
× 0.25
IOL = 4.0 mA 2.3~2.7 ⎯ ⎯ 0.4 ⎯ 0.4
IOL = 8.0 mA 3.0~3.6 ⎯ ⎯ 0.4 ⎯ 0.4
= 0~5.5V 0~3.6 ⎯ ⎯ ±0.1 ⎯ ±1.0 μA
IN
V
= 0~5.5V
IN
= 0~3.6V
V
OUT
= VCC or GND 3.6 ⎯ ⎯ 1.0 ⎯ 10.0 μA
IN
0 ⎯ ⎯ 1.0 ⎯ 10.0 μA
Unit
V
V
3
2007-11-01
TC7WG00FU/FK
AC Characteristics
Characteristics Symbol Test Condition
Propagation delay time
Input capacitance CIN ⎯ 3.6 ⎯ 3 ⎯ ⎯ ⎯ pF
Power dissipation capacitance CPD (Note13) 0.9 ~ 3.6 ⎯ 10 ⎯ ⎯ ⎯ pF
(Input: tr = tf = 3 ns)
CL = 10 pF,
= 1 MΩ
R
L
t
pLH
CL = 15 pF,
= 1 MΩ
R
L
t
pHL
= 30 pF,
C
L
= 1 MΩ
R
L
Ta = 25°C Ta = −40~85°C
(V) Min Typ. Max Min Max
V
CC
0.9 ⎯ 26.9 ⎯ ⎯ ⎯
1.1~1.3 ⎯ 10.9 20.7 1.0 38.6
1.4~1.6 ⎯ 5.9 9.6 1.0 11.3
1.65~ 1.95 ⎯ 4.5 7.0 1.0 7.5
2.3~2.7 ⎯ 2.9 4.4 1.0 4.9
3.0~3.6 ⎯ 2.2 3.5 1.0 4.1
0.9 ⎯ 30.0 ⎯ ⎯ ⎯
1.1~1.3 ⎯ 12.0 24.2 1.0 42.0
1.4~1.6 ⎯ 6.5 10.5 1.0 12.6
1.65~ 1.95 ⎯ 5.0 7.7 1.0 8.0
2.3~2.7 ⎯ 3.2 4.9 1.0 5.6
3.0~3.6 ⎯ 2.5 3.8 1.0 4.4
0.9 ⎯ 45.0 ⎯ ⎯ ⎯
1.1~1.3 ⎯ 18.0 33.4 1.0 63.2
1.4~1.6 ⎯ 8.9 14.8 1.0 17.9
1.65~ 1.95 ⎯ 6.9 10.3 1.0 10.8
2.3~2.7 ⎯ 4.4 6.4 1.0 6.8
3.0~3.6 ⎯ 3.5 4.9 1.0 5.4
Unit
ns
Note 13: CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating
current consumption without load.
Average operating current can be obtained by the equation:
I
CC (opr.)
= CPD･VCC･fIN + ICC/2
4
2007-11-01
Package Dimensions
TC7WG00FU/FK
Weight: 0.02 g (typ.)
5
2007-11-01
Package Dimensions
TC7WG00FU/FK
Weight: 0.01 g (typ.)
6
2007-11-01
TC7WG00FU/FK
RESTRICTIONS ON PRODUCT USE
• The information contained herein is subject to change without notice.
• TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor
devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical
stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of
safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of
such TOSHIBA products could cause loss of human life, bodily injury or damage to property.
In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as
set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and
conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability
Handbook” etc.
• The TOSHIBA products listed in this document are intended for usage in general electronics applications
(computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances,
etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires
extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or
bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or
spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments,
medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his
document shall be made at the customer’s own risk.
• The products described in this document shall not be used or embedded to any downstream products of which
manufacture, use and/or sale are prohibited under any applicable laws and regulations.
• The information contained herein is presented only as a guide for the applications of our products. No
responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which
may result from its use. No license is granted by implication or otherwise under any patents or other rights of
TOSHIBA or the third parties.
20070701-EN GENERAL
• Please contact your sales representative for product-by-product details in this document regarding RoHS
compatibility. Please use these products in this document in compliance with all applicable laws and regulations
that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses
occurring as a result of noncompliance with applicable laws and regulations.
7
2007-11-01
Loading...