Toshiba SL-4700 User Manual

Page 1
TEC Electronic Computing Scale
SL-4700 SERIES
Owner's Manual
Page 2
Declaration of Conformity
Manufacturer TOSHIBA TEC
Type SL-4700
No. of EC type approval
T5982
certificate
Corresponds to the requirements of the following EC directives:
Non-Automatic Weighing
Directive 90/384/EEC
1
Instruments
EMC Directive EMC 89/336/EEC
Low Voltage Directive LVD 73/23/EEC
The applicable harmonised standards are:
EN 45 501
EN50 081-1
EN 60 950
EMC Compliance
This is a class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures.
Note 1: This declaration is only valid if the non-automatic weighing instrument was verified by the manufacturer or with a certificate of conformity issued by a notified body.
Copyright © 2003 By TOSHIBA TEC CORPORATION All Rights Reserved 570 Ohito, Ohito-cho, Tagata-gun, Shizuoka-ken, JAPAN
Page 3
in part without prior
Contents
page no.
1 Warnings 5
2 Specifications 8
3 Installation 10
4 Error Messages 15
5 Using the Scale 16
6 Management Mode 18
7 Before you call for service 22
SL-4700 Owner Manual 3
CAUTION:
1. This manual may not be copied in whole or written permission of TOSHIBA TEC.
2. The contents of this manual may be changed without notification.
3. Please refer to your local Authorised Service representative with regard to queries you may have in this manual.
Page 4
Page 5
1 Warnings
For your protection, all mains (110V or 230V) equipment used where damp or wet conditions may occur, must be supplied
from a correctly fused source and protected by an approved RCD to BS7071 or BS7288 or IEC1008-2-2 BS EN 61008:1995. IF IN DOUBT SEEK ADVICE FROM A QUALIFIED ELECTRICIAN.
To avoid the possibility of electric shock or damage to the machine, always isolate from the mains power supply before carrying out any routine maintenance.
Cleaning the scale
Harsh abrasives, solvents, scouring cleaners and alkaline cleaning solutions, such as washing soda, should not be used especially on the display windows. Under no circumstances should you attempt to wipe the inside of the machine.

1 Warnings

The outside of the machine may be wiped down with a clean cloth moistened with water containing a small amount of washing up liquid.
SL-4700 Owner Manual
5
Page 6
1 Warnings
Safety Summary
Safety Summary
Personal safety in handling or maintaining the equipment is extremely important. Warnings and Cautions
Personal safety in handling or maintaining the equipment is extremely important. Warnings and Cautions necessary for safe handling are included in this manual. All warnings and cautions contained in this
necessary for safe handling are included in this manual. All warnings and cautions contained in this manual should be read and understood before handling or maintaining the equipment.
manual should be read and understood before handling or maintaining the equipment. Do not attempt to effect repairs or modifications to this equipment. If a fault occurs that cannot be rectified
Do not attempt to effect repairs or modifications to this equipment. If a fault occurs that cannot be rectified using the procedures described in this manual, turn off the power, unplug the machine, then contact your
using the procedures described in this manual, turn off the power, unplug the machine, then contact your authorized TOSHIBA TEC representative for assistance.
authorized TOSHIBA TEC representative for assistance.
Meanings of Each Symbol
Meanings of Each Symbol
This symbol indicates warning items (including cautions).
This symbol indicates warning items (including cautions). Specific warning contents are drawn inside the symbol.
Specific warning contents are drawn inside the symbol. (The symbol on the left indicates a general caution.)
(The symbol on the left indicates a general caution.)
This symbol indicates prohibited actions (prohibited items).
This symbol indicates prohibited actions (prohibited items). Specific prohibited contents are drawn inside or near the symbol.
Specific prohibited contents are drawn inside or near the symbol. (The symbol on the left indicates no disassembling.)
(The symbol on the left indicates no disassembling.)
This symbol indicates actions which must be performed.
This symbol indicates actions which must be performed. Specific instructions are drawn inside or near the symbol.
Specific instructions are drawn inside or near the symbol. (The symbol on the left indicates disconnect the power cord plug from the outlet.)
(The symbol on the left indicates disconnect the power cord plug from the outlet.)
This indicates that there is the risk of death or serious injury if the
This indicates that there is the risk of death or serious injury if the machines are improperly handled contrary to this indication.
WARNING
WARNING
Any other than the
Any other than the specified AC voltage
specified AC voltage is prohibited.
is prohibited.
Do not use voltages other than the
Do not use voltages other than the voltage (AC) specified on the rating
voltage (AC) specified on the rating plate, as this may cause fire or
plate, as this may cause fire or
electric shock.
electric shock.
machines are improperly handled contrary to this indication.
Do not plug in or unplug the power
Prohibited
Prohibited
Do not plug in or unplug the power cord plug with wet hands as this may
cord plug with wet hands as this may cause electric shock.
cause electric shock.
Prohibited
Prohibited
Prohibited
Prohibited
Disconnect
Disconnect the plug.
the plug.
If the machines share the same outlet with any other electrical
outlet with any other electrical appliances that consume large
appliances that consume large amounts of power, the voltage will
amounts of power, the voltage will fluctuate widely each time these
fluctuate widely each time these appliances operate. Be sure to
appliances operate. Be sure to provide an exclusive outlet for the
provide an exclusive outlet for the machine as this may cause fire or
machine as this may cause fire or
electric shock.
electric shock.
Do not insert or drop metal,
Do not insert or drop metal, flammable or other foreign objects into
flammable or other foreign objects into the machines through the ventilation
the machines through the ventilation slits, as this may cause fire or electric
slits, as this may cause fire or electric
shock.
shock.
If the machines are dropped or their
If the machines are dropped or their cabinets damaged, first turn off the
cabinets damaged, first turn off the power switches and disconnect the
power switches and disconnect the power cord plugs from the outlet, and
power cord plugs from the outlet, and then contact your authorized
then contact your authorized TOSHIBA TEC representative for
TOSHIBA TEC representative for assistance. Continued use of the
assistance. Continued use of the machine in that condition may cause
machine in that condition may cause
fire or electric shock.
fire or electric shock.
Prohibited
Prohibited
Prohibited
Prohibited
Disconnect
Disconnect the plug.
the plug.
Do not place metal objects or
Do not place metal objects or water-filled containers such as flower
water-filled containers such as flower vases, flower pots or mugs, etc. on
vases, flower pots or mugs, etc. on top of the machines. If metal objects
top of the machines. If metal objects or spilled liquid enter the machines,
or spilled liquid enter the machines, this may cause fire or electric
this may cause fire or electric
shock.
shock.
Do not scratch, damage or modify
Do not scratch, damage or modify the power cords. Also, do not place
the power cords. Also, do not place heavy objects on, pull on, or exces-
heavy objects on, pull on, or exces­sively bend the cords, as this may
sively bend the cords, as this may cause fire or electrical shock.
cause fire or electrical shock.
Continued use of the machines in an
Continued use of the machines in an abnormal condition such as when the
abnormal condition such as when the machines are producing smoke or
machines are producing smoke or strange smells may cause fire or elec-
strange smells may cause fire or elec-
tric shock. In these cases, immedi-
tric shock. In these cases, immedi-
ately turn off the power switches and
ately turn off the power switches and disconnect the power cord plugs from
disconnect the power cord plugs from the outlet. Then, contact your author-
the outlet. Then, contact your author­ized TOSHIBA TEC representative for
ized TOSHIBA TEC representative for assistance.
assistance.
If the machines share the same
6 SL-4700 Owner Manual
Page 7
1 Warnings
Disconnect the plug.
Connect a grounding wire.
CAUTION
Precautions
The following precautions will help to ensure that this machine will continue to function correctly.
 Try to avoid locations that have the following adverse conditions:
* Temperatures out of the specification * Direct sunlight * High humidity
* Shared power source * Excessive vibration * Dust/Gas  Do not subject the machine to sudden shocks.  Do not press the keys too hard. Keys will operate correctly if they are touched lightly.  Clean the cover and keyboard, etc. by wiping with a dry cloth or a cloth soaked with detergent and wrung out
thoroughly. Never use thinner or other volatile solvent for cleaning.  To ensure that the scale is operating correctly, place a known weight on the platter and check it for correct
weight measurement. This should be done every morning before starting normal operations.  When moving the machine, take hold of the case and lift the machine. Never hold the remote unit.  Do not place the machines on unstable or slanted surfaces, as they may drop or fall and cause injury.  USE ONLY TOSHIBA TEC SPECIFIED paper.  DO NOT STORE the paper or ribbons where they might be exposed to direct sunlight, high temperatures, high
humidity, dust, or gas.  Ensure the machine is operated on a level surface.  Any data stored in the memory of the machine could be lost during a machine fault.  Try to avoid using this equipment on the same power supply as high voltage equipment or equipment likely to
cause mains interference.  Unplug the machine whenever you are working inside it or cleaning it.  Keep your work environment static free.  Do not place heavy objects on top of the machines, as these items may become unbalanced and fall causing
injury.  Do not block the ventilation slits of the machines, as this will cause heat to build up inside the machines and
may cause fire.  Do not lean against the machine. It may fall on you and could cause injury.  Care must be taken not to injure yourself with the printer paper cutter.  Unplug the machine when it is not used for a long period of time.
Request Regarding Maintenance
 Utilize our maintenance services.
After purchasing the machine, contact your authorized TOSHIBA TEC representative for assistance once a
year to have the inside of the machine cleaned. Otherwise, dust will build up inside the machines and may
cause a fire or a malfunction. Cleaning is particularly effective before humid rainy seasons.  Our preventive maintenance service performs the periodic checks and other work required to maintain the
quality and performance of the machines, preventing accidents beforehand.
For details, please consult your authorized TOSHIBA TEC representative for assistance.  Using insecticides and other chemicals
Do not expose the machines to insecticides or other volatile solvents. This will cause the cabinet or other parts
to deteriorate or cause the paint to peel.
If foreign obj ects (meta l fragments, water, liquids) enter the machines, first turn off the power switches and disconnect the power cord plugs from the outlet, and then contact your authorized TOSHIBA TEC repre­sentative for assistance. Continued use of the machine in that condition may cause fire or electric shock.
Ensure that the equipment is properly grounded. Extension cables should also be grounded. Fire or electric shock could occur on improperly grounded equipment.
This indicates that there is the risk of personal Injury or damage to objects if the machines are improperly handled contrary to this indication.
Disconnect the plug.
No disassem­bling.
When unplugging the power cords, be sure to hold and pull on the plug portion. Pulling on the cord portion may cut or expose the internal wires and cause fire or electric shock.
Do not remove covers, repair or modify the machine by yourself. You may be injured by high voltage, very hot parts or sharp edges inside the machine.
SL-4700 Owner Manual
7
Page 8

2 Specifications

2 Specifications
Item SL-4700-US Weigh capacity 30lb x 0.01lb Tare capacity (maximum) 15lb Display 4 digits LCD Power requirement AC 120V ± 10%, 60Hz Operating temperature 14° F to 104° F Operating humidity 0% to 95% RH (non-condensing) Dimensions (appox.)
Built-in type 13.78”(W) x 11.81”(D) x 3.43”(H) Remote display type
Scale unit 13.78”(W) x 11.02”(D) x 3.43”(H) Display unit 5.98”(W) x 2.32”(D) x 15.35”(H)
Platter 13.78”(W) x 11.02”(D) Weight (approx.) Interface RS-232C, TEC parallel
Built-in type: 9.5lb Remote display type: 10.6lb
Item SL-4700-CA/QP/AU Weigh capacity 15kg x 5g Tare capacity (maximum) 7.5kg Display 5 digits LCD
CA: AC 120V ± 10%, 60Hz
Power requirement
Operating temperature -10° C to 40° C Operating humidity 0% to 95% RH (non-condensing)
8 SL-4700 Owner Manual
QP: AC 230V ± 10%, 50Hz (AC adaptor
option)
AU: AC 100V to 240V, 47Hz to 63Hz
Page 9
Dimensions (appox.)
Scale unit Display unit Platter
Weight (approx.)
350mm(W) x 280mm(D) x 87mm(H) 152mm(W) x 59mm(D) x 390mm(H) 350mm(W) x 280mm(D)
4.8kg
Interface RS-232C, TEC parallel
Options and accessories
Options
AC adaptor for QP model
EU plug UK plug
Accessories
TEC parallel cable for TD/ TP models AC adaptor for US/CA/AU models
2 Specifications
SL-4700 Owner Manual
9
Page 10

3 Installation

3Installation
1. Make sure that the work surface is firm, steady and free
from vibration and draughts.
2. Hold the scale by the base when picking up. Do not
pick up the scale by the weigh plate or cross.
3. Adjust the feet if the scale is not level.
To avoid the risk of RSI (Repetitive Strain Injury) it is important to ensure that the machine is placed on a surface which is ergonomically satisfactory to the user. In cases where usage is prolonged EN614-1 recommends frequent breaks for the user.
10 SL-4700 Owner Manual
Page 11

Connections

1. Remove the weigh plate.
2. Connect the power cable.
3 Installation
SL-4700 Owner Manual
11
Page 12
3 Installation
3.
Connect the display. (RP/TP models only)
4.
Replace the weigh plate. Connect to power supply.
12 SL-4700 Owner Manual
Page 13

Cable routing

3 Installation
1
2
3
4
4
8
7
3
5
9
6
2
1
SL-4700 Owner Manual
1
2
3
4
13
Page 14
3 Installation
Securing cable clips
14 SL-4700 Owner Manual
Page 15
4 Error Messages

4 Error Messages

(
Display overflow error
The load on the weighpan exceeds the scale capacity.
Balance failed error
On power up the weight is out of the allowed zero range. Check there is no load or debris on the weighpan.
Error codes:
E10 Battery failure. Replace the batteries.
E30 Management mode not exited correctly. Re-enter
E35 Prohibited function.
E151Configuration change in Management mode has
E152Prohibited function.
Contact your authorised service agent if the scale remains inoperative or you see any other error message code.
If a persistent error message appears or the scale locks up, disconnect then reconnect the scale to the power supply. If the scale remains inoperative, contact your authorised service agent.
Display
overflow
Under
range
Management mode and repeat the procedure.
failed. Re-enter Management mode and repeat the procedure
Weight
unsteady
Over
range
Balance
failed
SL-4700 Owner Manual
15
Page 16

5 Using the Scale

5 Using the Scale
Testing the display
Press
Displaying service information
Press twice
To reset the machine
LCD
Press and hold
LCD
Zeroing the scale
Make sure that the scale is at zero before weighing.
16 SL-4700 Owner Manual
Page 17
Weighing goods
5 Using the Scale
SL-4700 Owner Manual
17
Page 18

6 Management Mode

6 Management Mode
Entering management mode
LCD
Navigating management mode
C
Branch - 6 - Sub-branch - Value
Go to the next branch (press and hold). Go to next sub-branch.
Go to the previous branch (press and hold). Go to previous sub-branch.
Sets the value to 0 enabling you to display a
C
new value. Return to Branch 00 (press and hold).
Displays the value. Press again to re-display the branch / sub-branch.
After clearing a value to be changed each key press increments the value displayed. Pressing and holding the key increments the value by 10.
For Example: Branch ()
Sub-branch () Branch ()
Sub-branch () Sub-branch ()
Note: After changing a value, you must go to the next branch to accept the value.
18 SL-4700 Owner Manual
Page 19
6 Management Mode
Example
Turn the keyboard bleeper off and change the backlight time to 5 seconds.
6
Press and hold
6 6
6
Press and hold
Switching the bleeper alarm on/off
Go to branch 19, Sub-branch 00
0 = Off 1 = On
6
Switching the keyboard bleeper on/off
Go to branch 19, Sub-branch 01
0 = Off 1 = On
6
C
Target bleep
Branch 19, Sub-branch 02 - Not applicable for this machine.
SL-4700 Owner Manual
19
Page 20
6 Management Mode
Error bleeper
Go to branch 19, Sub-branch 03
1
0 = Off 1 = On
19.03
Changing the bleeper volume
Go to branch 19, Sub-branch 04
1
0 = Quiet 1 = Loud
19.04
Backlight timeout
Branch 20, Sub-branch 00 - Not applicable for this machine.
Sleep timeout
Branch 20, Sub-branch 01 - Not applicable for this machine.
20 SL-4700 Owner Manual
Page 21
6 Management Mode
Sleep key enable
Branch 20, Sub-branch 02 - Not applicable for this machine.
LED display brightness
Branch 20, Sub-branch 03 - Not applicable for this machine.
Changing the duration of a ‘Long’ press
(press and hold)
Go to branch 29, Sub-branch 00
29.00 200
Enabling key timeout
Go to branch 74, Sub-branch 01
74.01
SL-4700 Owner Manual
Enter a value in units of 10 milliseconds (50 - 255). For example: 200 = 2 seconds 150 = 1 100 = 1 second
0 = Disabled 1 = Enabled
1
½ seconds
21
Page 22

7 Before you call for service

Changing the timeout period
Go to branch 74, Sub-branch 02
6
Enter a value in units of 10 milliseconds (1 - 255). For example:

200 = 2 seconds 150 = 1
½ seconds
100 = 1 second
7 Before you call for service
It is our primary concern to give you full satisfaction and better service. If, however, any problem arises in connection with the operation of this scale, please check the following points before calling for service.
Is the power plug fully plugged into an AC outlet?
Is the AC power being properly supplied to the outlet?
(Check it using another electrical appliance.)
Check the circuit breaker.
Has there been a power failure of any sort?
WARNING: This scale has been manufactured under strict quality control. If you have trouble, however, DO NOT ATTEMPT TO FIX IT BY YOURSELF. Disconnect the power supply and contact your C>B7810C42 representative.
22 SL-4700 Owner Manual
Page 23
Page 24
EO1-31010B
E
Loading...