Toshiba Satellite 2430, Satellite 2435 User Manual

Satellite® 2430/2435 Series User’s Guide

If you need assistance:

❖ InTouch

Calling within the United States [phone]
Calling from outside the United States [phone]

For more information, see “If Something Goes Wrong” on

page 179 in this guide.

®

Center

TOSHIBA

C6633-1202M1

2

Model: Satellite 2430/2435

ReWritable CD/DVD Drives

The computer system you purchased may include a ReWritable CD and/or
DVD drive(s), among the most advanced data storage technologies
available. As with any new technology, you must read and follow all set-up
and usage instructions in the applicable user guides and/or manuals
enclosed. If you fail to do so, this product may not function properly and
you may lose data or suffer other damage. TOSHIBA AMERICA
INFORMATION SYSTEMS (“TOSHIBA”), ITS AFFILIATES AND
SUPPLIERS DO NOT WARRANT THAT OPERATION OF THE
PRODUCT WILL BE UNINTERRUPTED OR ERROR FREE. YOU
AGREE THAT TOSHIBA, ITS AFFILIATES AND SUPPLIERS SHALL
HAVE NO RESPONSIBILITY FOR DAMAGE TO OR LOSS OF ANY
BUSINESS, PROFITS, PROGRAMS, DATA OR REMOVABLE
STORAGE MEDIA ARISING OUT OF OR RESULTING FROM THE
USE OF THE PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY
THEREOF.

Protection of Stored Data

For your important data, please make periodic back-up copies of all the
data stored on the hard disk or other storage devices as a precaution against
possible failures, alteration, or loss of the data. IF YOUR DATA IS

ALTERED OR LOST DUE TO ANY TROUBLE, FAILURE OR
MALFUNCTION OF THE HARD DISK DRIVE OR OTHER
STORAGE DEVICES AND THE DATA CANNOT BE RECOVERED,
TOSHIBA SHALL NOT BE LIABLE FOR ANY DAMAGE OR LOSS
OF DATA, OR ANY OTHER DAMAGE RESULTING
THEREFROM. WHEN COPYING OR TRANSFERRING YOUR
DATA, PLEASE BE SURE TO CONFIRM WHETHER THE DATA
HAS BEEN SUCCESSFULLY COPIED OR TRANSFERRED.
TOSHIBA DISCLAIMS ANY LIABILITY FOR THE FAILURE TO
COPY OR TRANSFER THE DATA CORRECTLY.

Critical Applications

The computer you have purchased is not designed for any “critical
applications.” “Critical applications” means life support systems, medical
applications, connections to implanted medical devices, commercial
transportation, nuclear facilities or systems or any other applications where
product failure could lead to injury to persons or loss of life or catastrophic
property damage. ACCORDINGLY, TOSHIBA, ITS AFFILIATES

AND SUPPLIERS DISCLAIM ANY AND ALL LIABILITY
ARISING OUT OF THE USE OF THE COMPUTER PRODUCTS IN

ANY CRITICAL APPLICATIONS. IF YOU USE THE COMPUTER
PRODUCTS IN A CRITICAL APPLICATION, YOU, AND NOT
TOSHIBA, ASSUME FULL RESPONSIBILITY FOR SUCH USE.

FCC Notice

This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, it may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:

❖ Reorient or relocate the receiving antenna.

❖ Increase the separation between the equipment and receiver.

❖ Connect the equipment to an outlet on a circuit different from that to

which the receiver is connected.

❖ Consult the dealer or an experienced radio/TV technician for help.

3

NOTE: Only Peripherals complying with the FCC Class B limits may be attached
to this equipment. Operation with noncompliant peripherals or peripherals not
recommended by Toshiba is likely to result in interference to radio and TV
reception. Shielded cables must be used between the external devices and the
computer's or expansion unit's serial port, parallel port, monitor port, USB port,

®

PS/2 port
to this equipment not expressly approved by Toshiba or parties authorized by
Toshiba could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:

, i.LINK® port and microphone jack. Changes or modifications made

❖ This device may not cause harmful interference.

❖ This device must accept any interference received, including

interference that may cause undesired operation.

4

Contact:

Toshiba America Information Systems, Inc.

9740 Irvine Blvd.
Irvine, CA 92618-1697
[phone]

Industry Canada Requirement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conformé à la norme NMB-003
du Canada.

FCC Requirements

The following information is pursuant to FCC CFR 47, Part 68 and refers
to internal modems.

Installation

When you are ready to install or use the modem, call your local telephone
company and give them the following information:

❖ The telephone number of the line to which you will connect the

modem.

❖ The FCC registration number of the modem.

❖ The ringer equivalence number (REN) of the modem, which is 0.6B.

The modem connects to the telephone line by means of a standard jack
called the USOC RJ11C.

Type of Service

Your modem is designed to be used on standard-device telephone lines.
Connection to telephone company-provided coin service (central office
implemented systems) is prohibited. Connection to party lines service is
subject to State tariffs. If you have any questions about your telephone line,
such as how many pieces of equipment you can connect to it, the telephone
company will provide this information upon request.

Telephone Company Procedures

The goal of the telephone company is to provide you with the best service it
can. In order to do this, it may occasionally be necessary for them to make
changes in their equipment, operations or procedures. If these changes
might affect your service or the operation of your equipment, the telephone

company will give you notice, in writing, to allow you to make any changes
necessary to maintain uninterrupted service.

If Problems Arise

If any of your telephone equipment is not operating properly, you should
immediately remove it from your telephone line, as it may cause harm to
the telephone network. If the telephone company notes a problem, they
may temporarily discontinue service. When practical, they will notify you
in advance of this disconnection. If advance notice is not feasible, you will
be notified as soon as possible. When you are notified, you will be given
the opportunity to correct the problem and informed of your right to file a
complaint with the FCC. In the event repairs are ever needed on your
modem, they should be performed by Toshiba Corporation, Toshiba
America Information Systems, Inc. or an authorized representative of
Tos hi ba .

Disconnection

If you should ever decide to permanently disconnect your modem from its
present line, please call the telephone company and let them know of this
change.

Fax Branding

The Telephone Consumer Protection Act of 1991 makes it unlawful to use
a computer or other electronic device to send any message via a telephone
fax machine unless such message clearly contains in a margin at the top or
bottom of each transmitted page or on the first page of the transmission, the
date and time it is sent and an identification of the business, other entity or
individual sending the message and the telephone number of the sending
machine or such business, other entity or individual.

In order to program this information into your fax modem, you should
complete the setup for your fax software before sending a message.

5

Instructions for IC CS-03 certified equipment

1 NOTICE: The Industry Canada label identifies certified equipment.

This certification means that the equipment meets certain
telecommunications network protective, operational and safety
requirements as prescribed in the appropriate Terminal Equipment
Technical Requirements document(s). The Department does not
guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is
permissible to be connected to the facilities of the local
telecommunications company. The equipment must also be installed
using an acceptable method of connection. The customer should be

6

aware that compliance with the above conditions may not prevent
degradation of service in some situations.

Repairs to certified equipment should be coordinated by a
representative designated by the supplier. Any repairs or alterations
made by the user to this equipment, or equipment malfunctions, may
give the telecommunications company cause to request the user to
disconnect the equipment.

Users should ensure for their own protection that the electrical ground
connections of the power utility, telephone lines and internal metallic
water pipe system, if present, are connected together. This precaution
may be particularly important in rural areas.

Caution: Users should not attempt to make such connections
themselves, but should contact the appropriate electric inspection
authority, or electrician, as appropriate.

2 The user manual of analog equipment must contain the equipment’s

Ringer Equivalence Number (REN) and an explanation notice similar
to the following:

The Ringer Equivalence Number (REN) of this device can be found
on the label affixed to your computer.

NOTICE: The Ringer Equivalence Number (REN) assigned to each
terminal device provides an indication of the maximum number of
terminals allowed to be connected to a telephone interface. The
termination on an interface may consist of any combination of devices
subject only to the requirement that the sum of the Ringer Equivalence
Numbers of all the devices does not exceed 5.

3 The standard connecting arrangement (telephone jack type) for this

equipment is jack type(s): USOC RJ11C.

Wireless Interoperability

The TOSHIBA Wireless LAN Mini PCI Card products are designed to be
interoperable with any wireless LAN product that is based on Direct
Sequence Spread Spectrum (DSSS) radio technology, and is compliant to:

❖ The IEEE 802.11 Standard on Wireless LANs (Revision A/B), as

defined and approved by the Institute of Electrical and Electronics
Engineers.

❖ The Wireless Fidelity (WiFi) certification as defined by the WECA

Wireless Ethernet Compatibility Alliance.

Caution

Bluetooth™ and Wireless LAN devices operate within the same radio
frequency range and may interfere with one another. If you use
Bluetooth™ and Wireless LAN devices simultaneously, you may
occasionally experience a less than optimal network performance or even
lose your network connection.

If you should experience any such problem, immediately turn off either one
of your Bluetooth™ or Wireless LAN.

Please contact Toshiba PC product support on web site http://www.toshiba­europe.com/computers/tnt/bluetooth.htm in Europe or
http://www.pcsupport.global.toshiba.com in the United States for more
information.

Caution

This device is restricted to indoor use due to its operation in the 5.15 to

5.85 GHz frequency range.

Wireless LAN and your Health

Wireless LAN products, like other radio devices, emit radio frequency
electromagnetic energy. The level of energy emitted by Wireless LAN
devices however is far much less than the electromagnetic energy emitted
by wireless devices like for example mobile phones.

Because Wireless LAN products operate within the guidelines found in
radio frequency safety standards and recommendations, TOSHIBA
believes Wireless LAN is safe for use by consumers. These standards and
recommendations reflect the consensus of the scientific community and
result from deliberations of panels and committees of scientists who
continually review and interpret the extensive research literature.

In some situations or environments, the use of Wireless LAN may be
restricted by the proprietor of the building or responsible representatives of
the organization. These situations may for example include:

❖ Using the Wireless LAN equipment on board of airplanes, or

❖ In any other environment where the risk of interference to other

devices or services is perceived or identified as harmful.

If you are uncertain of the policy that applies on the use of wireless devices
in a specific organization or environment (e.g. airports), you are
encouraged to ask for authorization to use the Wireless LAN device prior to
turning on the equipment.

7

8

Regulatory Information

The TOSHIBA Wireless LAN Mini PCI Card must be installed and used in
strict accordance with the manufacturer’s instructions as described in the
user documentation that comes with the product. This device complies with
the following radio frequency and safety standards.

Canada – Industry Canada (IC)

This device complies with RSS 210 of Industry Canada.

Operation is subject to the following two conditions: (1) this device may
not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of this device.

L ‘utilisation de ce dispositif est autorisée seulement aux conditions
suivantes: (1) il ne doit pas produire de brouillage et (2) l’ utilisateur du
dispositif doit étre prêt à accepter tout brouillage radioélectrique reçu,
même si ce brouillage est susceptible de compromettre le fonctionnement
du dispositif.

The term "IC" before the equipment certification number only signifies that
the Industry Canada technical specifications were met.

IC: 248H-DPA3233W

This device has been designed to operate with an antenna having a
maximum gain of 4.8dBi. Antenna having a higher gain is strictly
prohibited per regulations of Industry Canada. The required antenna
impedance is 50 ohms.

To reduce potential radio interference to other users, the antenna type and
its gain should be so chosen that the equivalent isotropically radiated power
(EIRP) is not more than that required for successful communication.

To prevent radio interference to the licensed service, this device is intended
to be operated indoors and away from windows to provide maximum
shielding. Equipment (or its transmit antenna) that is installed outdoors is
subject to licensing.

Europe – EU Declaration of Conformity

This device complies with the essential requirements of the R&TTE
Directive 1999/5/EC with essential test suites as per standards:

❖ EN 60950 Safety of Information Technology equipment

❖ ETS 300 328 Technical requirements for radio equipment

❖ ETS 300 826 General EMC requirements for radio equipment.

9

België/
Belgique:

Deutschland: License required for outdoor installations. Check with reseller for pro-

For outdoor usage only channel 10 (2457 MHz) and 11 (2462 MHz) is
allowed.

For private usage outside buildings across public grounds over less than
300m no special registration with IBPT/BIPT is required. Registration
to IBPT/BIPT is required for private usage outside buildings across
public grounds over more than 300m. An IBPT/BIPT license is
required for public usage outside building. For registration and license
please contact IBPT/BIPT.

Gebruik buiten gebouw alleen op kanalen 10 (2457 MHz) en 11 (2462
MHz). Voor privé-gebruik buiten gebouw over publieke groud over
afstand kleiner dan 300m geen registratie bij BIPT/IBPT nodig; voor
gebruik over afstand groter dan 300m is wel registratie bij BIPT/IBPT
nodig. Voor publiek gebruik buiten gebouwen is licentie van BIPT/
IBPT verplicht. Voor registratie of licentie kunt u contact opnemen met
BIPT.

L’utilisation en extérieur est autorisé sur le canal 10 (2457 MHz) et 11
(2462 MHz). Dans le cas d’une utilisation privée, a l’extérieur d’un
bâtiment, audessus d’un espace public, aucun enregistrement n’est
nécessaire pour une distance de moins de 300m. Pour une distance
supérieure à 300m un enregistrement auprés de I’IBPT est requise.
Pour une utilisation publique à I’extérieur de bâtiments, une licence de
I’IBPT est requise. Pour les enregistrements et licences, veuillez con­tacter I’IBPT.

cedure to follow.

Anmeldung im Outdoor-Bereich notwendig, aber nicht genehmigung­spflichtig. Bitte mit Händler die Vorgehensweise abstimmen.

France: Restricted frequency band: only channels 10 and 11 (2457 MHz and

2462 MHz respectively) may be used in France. License required for
every installation, indoor and outdoor installations. Please contact ART
for procedure to follow.

Bande de fréquence restreinte : seuls les canaux 10 à 11 (2457 et 2462
MHz respectivement) doivent être utilisés en France. Toute utilisation,
qu’elle soit intérieure ou extérieure, est soumise à autorisation. Vous
pouvez contacter I’Autorité de Régulation des Télécommuniations
(http://www.art-telecom.fr) pour la procédure à suivre.

10

Italia: License required for indoor use. Use with outdoor installations not

allowed.

E’necessaria la concessione ministeriale anche per l’uso interno. Verifi­care con i rivenditori la procedura da seguire. L’uso per installazione in
esterni non e’ permessa.

Nederland: License required for outdoor installations. Check with reseller for pro-

cedure to follow.

Licentie verplicht voor gebruik met buitenantennes. Neem contact op
met verkoper voor juiste procedure.

USA-Federal Communications Commission (FCC)

This device complies with Part 15 of FCC Rules. Operation of the devices in a
Wireless LAN System is subject to the following two conditions:

❖ This device may not cause harmful interference.

❖ This device must accept any interference that may cause undesired

operation.

TOSHIBA is not responsible for any radio or television interference caused
by unauthorized modification of the devices included with this TOSHIBA
Wireless LAN Mini PCI Card, or the substitution or attachment of
connecting cables and equipment other than specified by TOSHIBA.

The correction of interference caused by such unauthorized modification,
substitution or attachment will be the responsibility of the user.

Caution: Exposure to Radio Frequency Radiation

The Toshiba Wireless LAN Mini PCI Card will be installed with one of two
types of antennas. The both of antenna types, when installed are located at
the upper edge of the LCD screen.

For both antennas, the radiated output power of the TOSHIBA Wireless
LAN Mini PCI Card is far below the FCC radio frequency exposure limits.
Nevertheless, the TOSHIBA Wireless LAN Mini PCI Card shall be used in
such a manner that the potential for human contact during normal operation
is minimized. In normal operating configuration, the LCD in the upright
position, the distance between the antenna and the user should not be less
than 20cm. The antenna(s) used for this transmitter must not be co-located
or operating in conjunction with any other antenna or transmitter.

Antenna(s) used in 5.15-5.25GHz frequency band must be integral antenna
which provide no access to the end user.

Refer to the Regulatory Statements as identified in the documentation that
comes with those products for additional information.

Relevant transmitters include FCC IDs: CJ6UPA3233WL,
CJ6UPA3232BT.

The installer of this radio equipment must ensure that the antenna is located
or pointed such that it does not emit RF field in excess of Health Canada
limits for the general population; consult Safety Code 6, obtainable from
Health Canada’s website www.hc-sc.gc.ca/rpb.

Caution: Radio Frequency Interference Requirements

This device is restricted to indoor use due to its operation in the 5.15 to

5.25 GHz frequency range. FCC requires this product to be used indoors
for frequency range 5.15 to 5.25 GHz to reduce the potential for harmful
interference to co-channel Mobile Satellite systems.

High power radars are allocated as primary users of the 5.25 to 5.35 GHz
and 5.65 to 5.85 GHz bands. These radar stations can cause interference
with and/or damage this device.

Tai wa n

11

Article 14 Unless approved, for any model accredited low power radio frequency

electric machinery, any company, trader or user shall not change the
frequency, increase the power or change the features and functions of
the original design.

Article 17 Any use of low power radio frequency electric machinery shall not

affect the aviation safety and interfere with legal communications. In
event that any interference is found, the use of such electric machinery
shall be stopped immediately, and reusing of such products can be
resumed until no interference occurs after improvement.

The legal communications mentioned in the above item refer to radio
communications operated in accordance with telecommunication laws and
regulations.

Low power radio frequency electric machinery shall resist against
interference from legal communications or from industrial, scientific and
medical radio emission electric machinery.

12

Using this equipment in Japan

In Japan, the frequency bandwidth of 2,400.2,483.5MHz for second-generation
low-power data communication systems such as this equipment overlaps that of
mobile object identification systems (premises radio station and specified low­power radio station).

1. Sticker

Please put the following sticker on devices incorporating this product.

2. Indication

The indication shown below appears on this equipment.

1 2.4 this equipment uses a frequency of 2.4GHz.

2 DS.This equipment uses DS-SS modulation.

3 The interference range of this equipment is less than 40m.

4 This equipment uses a frequency bandwidth from 2,400 MHz to

2,483.5 MHz.

It is possible to avoid the band of mobile object identification systems.

3. TOSHIBA Direct PC

Monday – Friday: 10:00 – 17:00

Toll Free Tel: [phone]

Direct Dial: 03-3457-5916

Fax: [phone]

Device Authorization

This device obtains the Technical Regulation Conformity Certification and the
Technical Conditions Compliance Approval, and it belongs to the device class of
radio equipment of low-power data communication system radio station
stipulated in the Radio Law and the Telecommunications Business Law of Japan.

The Name of the radio equipment: PA3232U-1MPC

TELECOM ENGINEERING CENTER Approval Number: 03NY.A0018,
03GZDA0017

The following restrictions apply:

❖ Do not disassemble or modify the device.

❖ Do not install the embedded wireless module into other device.

13

Interference Statement

This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy. If not installed and used in accordance with the instructions, it may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try and correct the interference by one or more of the following
measures:

❖ Reorient or relocate the receiving antenna.

❖ Increase the distance between the equipment and the receiver.

❖ Connect the equipment to an outlet on a circuit different from that to

which the receiver is connected.

❖ Consult the dealer or an experienced radio/TV technician for help.

14

Toshiba is not responsible for any radio or television interference caused by
unauthorized modification of the devices included with this Toshiba
Wireless LAN Mini PCI Card, or the substitution or attachment of
connecting cables and equipment other than specified by Toshiba.

The correction of interference caused by such unauthorized modification,
substitution or attachment will be the responsibility of the user.

Approved Countries for use

This equipment is approved to the radio standard by the countries in Fig.1.

Australia Austria Belgium

Canada Denmark Finland

Germany Iceland Ireland

Japan Luxembourg Netherlands

New Zealand Norway Sweden

Switzerland UK USA

Greece Italy France

Poland Portugal Spain

Caution: Do not use this equipment except in the countries in Fig.1.

DVD-ROM, Multifunction drive safety instructions

The DVD-ROM and Multifunction drives employ a laser system. To ensure
proper use of this product, please read this instruction manual carefully and
retain for future reference. Should the unit ever require maintenance,
contact an authorized service location.

Use of controls, adjustments or the performance of procedures other than those
specified may result in hazardous radiation exposure.

To prevent direct exposure to the laser beam, do not try to open the enclosure.

enclosure.

Location of the required label

(Sample shown below. Location of the label and manufacturing
information may vary.)

15

CAUTIO N: This appliance contains a laser system and is classified as a “CLASS 1
LASER PRODUCT.” To use this model properly, read the instruction manual
carefully and keep it for your future reference. In case of any trouble with this
model, please contact your nearest “AUTHORIZED service station.” To prevent
direct exposure to the laser beam, do not try to open the enclosure.

Use of controls or adjustments or performance of procedures other than those
specified in the owner’s manual may result in hazardous radiation exposure.

Copyright

This guide is copyrighted by Toshiba America Information Systems, Inc.
with all rights reserved. Under the copyright laws, this guide cannot be
reproduced in any form without the prior written permission of Toshiba. No
patent liability is assumed, however, with respect to the use of the
information contained herein.

©2002 by Toshiba America Information Systems, Inc. All rights reserved.

Export Administration Regulation

This document contains technical data that may be controlled under the
U.S. Export Administration Regulations, and may be subject to the
approval of the U.S. Department of Commerce prior to export. Any export,
directly or indirectly, in contravention of the U.S. Export Administration
Regulations is prohibited.

16

Notice

The information contained in this manual, including but not limited to any
product specifications, is subject to change without notice.

TOSHIBA CORPORATION AND TOSHIBA AMERICA
INFORMATION SYSTEMS, INC. (TOSHIBA) PROVIDES NO
WARRANTY WITH REGARD TO THIS MANUAL OR ANY OTHER
INFORMATION CONTAINED HEREIN AND HEREBY EXPRESSLY
DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR ANY PARTICULAR PURPOSE WITH REGARD TO
ANY OF THE FOREGOING. TOSHIBA ASSUMES NO LIABILITY
FOR ANY DAMAGES INCURRED DIRECTLY OR INDIRECTLY
FROM ANY TECHNICAL OR TYPOGRAPHICAL ERRORS OR
OMISSIONS CONTAINED HEREIN OR FOR DISCREPANCIES
BETWEEN THE PRODUCT AND THE MANUAL. IN NO EVENT
SHALL TOSHIBA BE LIABLE FOR ANY INCIDENTAL,
CONSEQUENTIAL, SPECIAL, OR EXEMPLARY DAMAGES,
WHETHER BASED ON TORT, CONTRACT OR OTHERWISE,
ARISING OUT OF OR IN CONNECTION WITH THIS MANUAL OR
ANY OTHER INFORMATION CONTAINED HEREIN OR THE USE
THEREOF.

Trademarks

Satellite, InTouch, and Noteworthy are registered trademarks, SelectServ,
FreedomWare, and SmartMedia are trademarks, of Toshiba America
Information Systems, Inc. and/or Toshiba Corporation.

Microsoft, Windows, DirectX, Active Desktop, and DirectShow are
registered trademarks, and Windows Media is a trademark of Microsoft
Corporation.

LapLink is a registered trademark of Traveling Software, Inc.

WinDVD is a trademark of InterVideo, Inc.

CompuServe is a registered trademark of America Online, Inc.

Dolby - Manufactured by Toshiba under license from Dolby Laboratories/
Dolby and the double-D symbol are trademarks of Dolby Laboratories.

TouchPad is a trademark of Synaptics, Inc.

All other brand and product names are trademarks or registered trademarks
of their respective companies.

Computer Disposal Information

This product contains mercury. Disposal of this material may be regulated
due to environmental considerations. For disposal, reuse or recycling
information, please contact your local government or the Electronic
Industries Alliance at www.eiae.org.

Contents

Introduction ..............................................................25

This guide .............................................................. 25

Safety icons ........................................................... 26

Other icons used.............................................. 27

Other documentation ............................................. 27

Service options ...................................................... 28

Chapter 1: Finding Your Way Around ........................ 29

Making sure you have everything .......................... 29

Front with the display closed ................................. 30

Back....................................................................... 30

Right side............................................................... 32

Left side ................................................................. 33

Front with the display open.................................... 34

Indicator lights................................................. 36

Underside .............................................................. 37

17

Contents

18

Chapter 2: Getting Started ........................................ 39

Selecting a place to work ....................................... 39

Creating a computer-friendly environment....... 39

Keeping yourself comfortable .......................... 40

Precautions...................................................... 43

Setting up your computer ...................................... 45

Setting up your software.................................. 45

Registering your computer with Toshiba ......... 47

Adding external devices ................................... 47

Connecting the AC adapter..................................... 48

Charging the main battery...................................... 50

Using the computer for the first time..................... 51

Opening the display panel................................ 51

Turning on the power....................................... 51

Using the TouchPad™...................................... 52

Control buttons................................................ 53

Disabling or enabling the TouchPad................. 53

Installing additional memory (optional) ................. 54

Removing a memory module........................... 60

Connecting a mouse ........................................ 60

Connecting a printer ........................................ 61

Setting up a printer .......................................... 62

Turning off the computer ....................................... 65

Caring for your computer....................................... 66

Cleaning the computer..................................... 66

Moving the computer....................................... 67

Using a computer lock ..................................... 67

Contents

19

Chapter 3: Learning the Basics.................................. 69

Computing tips ...................................................... 69

Using the keyboard ................................................ 70

Character keys ................................................. 71

Ctrl, Fn, and Alt keys ........................................ 71

Function keys................................................... 71

Windows® special keys.................................... 72

Overlay keys..................................................... 72

Starting a program................................................. 74

Saving your work................................................... 74

Printing your work ................................................. 75

Backing up your files ............................................. 76

Using the DVD-ROM or Multifunction drive ........... 76

Drive components and control buttons............ 77

DVD-ROM drive components........................... 77

CD/DVD control buttons .................................. 78

CD/DVD control and digital audio modes......... 79

Inserting a disc ................................................ 80

Playing an audio CD......................................... 82

Playing a DVD .................................................. 84

Viewing the contents of a CD or DVD............... 84

Removing a disc with the computer on............ 84

Removing a disc with the computer off ........... 85

Caring for CDs and DVDs................................. 85

Setting up for communications.............................. 86

Connecting the modem to a phone line............ 86

Connecting your computer to a network.......... 86

Powering down the computer................................ 87

Using Turn Off or Shut down ................................. 88

Hibernation command ..................................... 89

Stand By command.......................................... 90

Turning off more quickly .................................. 91

Starting again after Turn Off............................. 92

Using Hibernation .................................................. 92

Contents

20

Starting again from Hibernation mode............. 94

Using Stand by ...................................................... 94

Going into Stand by mode more quickly .......... 95

Starting again from Stand by ........................... 96

Toshiba’s online resources..................................... 96

Chapter 4: Mobile Computing ................................... 97

Toshiba’s energy-saver design ............................... 97

Running the computer on battery power ............... 98

Power management ......................................... 99

Charging the battery .............................................. 99

Charging the RTC battery............................... 100

Monitoring battery power .................................... 101

Determining remaining battery power............ 101

Conserving battery power .............................. 102

What to do when the battery runs low ........... 103

Setting battery alarms.................................... 104

Changing the main battery ................................... 105

Removing the battery from the computer ...... 105

Taking care of your battery................................... 106

Maximizing battery life................................... 107

Disposing of used batteries safely ....................... 109

Traveling tips........................................................ 110

Chapter 5: Getting to Know the Windows® XP Operating

System............................................... 111

Lesson 1: Exploring the desktop.......................... 112

Finding your way around the desktop ............ 112

Windows
Lesson 2: Using the TouchPad and control buttons

together ........................................................ 115

Lesson 3: Learning about the Internet ................. 118

Lesson 4: Creating a new document .................... 119

Lesson 5: Creating a new folder........................... 120

®

XP file system .............................. 114

Contents

21

Lesson 6: Starting programs ............................... 121

Lesson 7: Resizing, repositioning, and hiding

windows ........................................................ 123

Using the taskbar........................................... 124

Minimizing and maximizing windows ............ 124

Resizing and moving windows....................... 125

Lesson 8: Closing programs ............................... 126

Lesson 9: Creating shortcuts ............................... 127

Creating a shortcut to the Calculator.............. 127

Creating a shortcut to the Character Map ...... 128

Lesson 10: Changing the screen saver................. 130

Lesson 11: Setting the date and time................... 132

Lesson 12: Removing objects from the desktop.. 134

Lesson 13: Using System Restore ....................... 136

Lesson 14: If I am lost, what do I do? ................. 137

Windows® XP Help and Support Center ........ 137

Using the online tours and tutorials ............... 139

Lesson 15: Turning off your computer................. 140

Chapter 6: Exploring Your Options .......................... 141

Windows® XP special features............................. 141

Personalizing your desktop.................................. 142

Customizing the taskbar ................................ 142

Bringing the world to your desktop................ 143

Changing desktop and browsing style ........... 144

Personalizing individual windows .................. 145

Customizing window toolbars........................ 146

Displaying information about each folder ...... 147

Using your computer at the office........................ 148

Setting up for communications...................... 149

Connecting the modem to a telephone line .... 150

Setting up a dial-up connection ..................... 150

Exchanging data with another computer.............. 151

22

Contents

Transferring files using a parallel port

connection ............................................... 151

Getting help transferring files......................... 152

Connecting to the Internet ................................... 152

An overview of using the Internet ........................ 153

The Internet ................................................... 153

The World Wide Web ..................................... 154

Internet Service Providers.............................. 154

Signing up with an Internet Service Provider 154

Surfing the Internet........................................ 155

Internet features............................................. 155

Uploading and downloading files

on the Internet ......................................... 156

Exploring video features ...................................... 157

Changing the display properties setting............... 157

Display settings hot key ................................ 158

Exploring audio features ...................................... 158

Recording sounds.......................................... 158

Using a microphone....................................... 159

Adjusting recording settings .......................... 160

Using external speakers or headphones......... 160

Connecting a monitor, keyboard and mouse........ 161

Using the Modular Bay......................................... 162

Removing a module from the Modular Bay.... 162

Inserting a module into the Modular Bay ....... 163

Using PC Cards.................................................... 164

PC Card supporting software ......................... 164

Inserting PC Cards......................................... 164

Removing PC Cards....................................... 165

Hot swapping................................................. 166

Contents

23

Chapter 7: WinDVD™ .............................................. 167

Playing DVDs .......................................................167

Using the WinDVD control panel ..........................170

Using WinDVD Advanced Features ......................174

Using playlists .....................................................175

Getting Help .........................................................178

Exiting WinDVD ...................................................178

Chapter 8: If Something Goes Wrong ..................... 179

Problems when you turn on the computer........... 182

The Windows® operating system is not working . 183

Using Startup options to fix problems ........... 183

Internet problems .......................................... 184

The Windows® XP operating system

can help you ............................................ 185

Resolving a hardware conflict.............................. 185

A plan of action.............................................. 186

Resolving hardware conflicts on your own .... 186

Fixing a problem with Device Manager .......... 188

Memory card problems.................................. 190

Power and the batteries ................................. 190

Keyboard problems........................................ 192

Display problems ........................................... 192

Disk drive problems....................................... 194

DVD-ROM or multifunction drive problems ... 196

Sound system problems ................................ 204

PC Card problems.......................................... 204

Printer problems............................................ 207

Modem problems........................................... 208

Develop good computing habits .......................... 209

If you need further assistance.............................. 210

Before you call ............................................... 210

Contacting Toshiba ........................................ 211

Other Toshiba Internet Web sites ........................ 212

Contents

24

Toshiba’s worldwide offices ................................. 212

Appendix A: Hot Keys ............................................. 215

Instant password security.................................... 215

Without a password....................................... 215

With a password ............................................ 215

Maintaining security when the battery isn’t fully

charged.................................................... 216

Sound .................................................................. 217

Power usage mode ............................................. 217

Stand by mode..................................................... 218

Hibernation mode ............................................... 219

Display modes ..................................................... 220

Display modes ..................................................... 220

Enabling a wireless device ................................... 221

Disabling or enabling the TouchPad..................... 221

Keyboard hot keys ............................................... 222

Appendix B: Power Cable Connectors..................... 223

Glossary ................................................................. 224

Index ....................................................................... 239

Introduction

Welcome to the world of powerful and portable multimedia
computers! With your new Toshiba notebook computer, your
access to information can accompany you wherever you go.

You will find your operating system, Microsoft
already installed on your computer. Your operating system offers
exciting features and easy Internet access.

This guide contains information about your operating system and
how it functions with your Toshiba computer. For specific
information on the software, see the Microsoft booklet that
shipped with your computer.

This guide

This guide introduces the computer’s features. You can:

❖ Read the entire guide from beginning to end.

❖ Skim through and stop when a topic interests you.

❖ Use the table of contents and the index to find specific

information.

®

Windows® XP

25

Introduction

26

Safety icons

If you are new to computers, or have not used a notebook
computer before, read through the first couple of chapters to
familiarize yourself with the components of the computer and how
to turn it on. After that, seek out whatever interests you most.

Safety icons

This manual contains safety instructions that must be observed in
order to avoid potential hazards that could result in personal
injuries, damage to your equipment, or loss of data. These safety
cautions have been classified according to the seriousness of the
risk, and the icons highlight these instructions as follows:

DANGER: This icon indicates the existence of a hazard that could
result in death or serious bodily injury if the safety instruction is
not observed.

WARNING: This icon indicates the existence of a hazard that could
result in bodily injury if the safety instruction is not observed.

CAUTION: This icon indicates the existence of a hazard that could
result in damage to equipment or property if the safety instruction
is not observed.

NOTE: This icon indicates information that relates to the safe
operation of the equipment or related items.

Other icons used

Additional icons highlight other helpful or educational
information:

TECHNICAL NOTE: This icon highlights technical information
about the computer.

HINT: This icon denotes helpful hints and tips.

DEFINITION: This icon indicates the definition of a term used in
the text.

Introduction

Other documentation

27

Other documentation

Your computer comes with the following documentation:

❖ This electronic user’s guide. Look for the user’s guide icon on

your desktop or in the DOCS folder on the C: drive.

❖ Guides for other programs that may come preinstalled on

your computer or that are available for installation on your
Recovery CDs.

❖ For accessory information, visit Toshiba's web site at

toshiba.com.

❖ The Microsoft

which explains the features of the operating system.

®

Windows® operating system documentation

Introduction

28

Service options

Service options

Toshiba offers a full line of service options built around its
SelectServ
Toshiba’s Web site at

If you have a problem or need to contact Toshiba, see “If

Something Goes Wrong” on page 179.

TM

warranty programs. For more information, visit

toshiba.com.

Chapter 1

Finding Your Way
Around

This chapter presents a “grand tour” of your notebook
computer. It serves as a reference when you need to locate
specific parts of the computer.

Making sure you have everything

Before doing anything else, consult the Quick Start card
provided with your system to make sure you received
everything. If any items are missing or damaged, notify your
dealer immediately. For additional help, see “If you need

further assistance” on page 210.

29

Finding Your Way Around

30

Front with the display closed

Front with the display closed

Display latch

CD/DVD control buttons

The display latch keeps the display panel closed and locked.
To open the display panel, press the display latch and raise
the panel.

The CD/DVD control buttons let you play audio CDs when
the computer is turned off. You can also use them to play CDs
and DVDs with the computer turned on. For more
information, see “CD/DVD control buttons” on page 78.

Back

USB ports

Modem port

Network port

System indicators

Parallel port

RGB (monitor)
port

S-video port

Cooling vent

DC IN

The DC IN port is where you plug in the AC adapter for
either operating the computer on external power or charging
the battery.

The S-video port lets you play DVD audio and video on a
projector or TV that accepts video inputs.

Ether

Finding Your Way Around

Back

The RGB (monitor) port lets you connect an external
monitor.

The parallel port lets you connect a parallel printer or other
parallel device, including ECP-compatible devices.

The modem port lets you use a standard RJ-11 telephone
cable to connect the modem directly to a standard telephone
line. For more information, see “Connecting the modem to a

phone line” on page 86.

The Network port (RJ-45 jack) provides access to a Local

Ether

Area Network (LAN) using a standard Ethernet

®

cable.

The USB (Universal Serial Bus) ports allow you to connect
USB peripherals to your computer.

DEFINITION: USB is a peripheral expansion standard that
supports a data-transfer rate of up to 480 Mbps for peripherals
such as keyboards, pointing devices, and monitors. USB
peripherals have a single standard for cabling and connectors. The
USB standard allows hot swapping of peripherals.

31

network

The cooling vent prevents the computer’s central processing
unit (CPU) from overheating so that it can continue to
perform at maximum speed.

CAUTION: To prevent possible overheating of the CPU, do not
block the cooling vents.

Finding Your Way Around

32

Right side

Right side

SD® card slot

USB Port

Speaker

The two stacked PC Card slots support up to two Type I or
Type II PC Cards, or one Type III PC Card. See “Using PC

Cards” on page 164 for more information.

The PC Card eject buttons release PC Cards from the
corresponding slots.

The SD® card slot holds a highly secure, stamp-size flash
memory card with a capacity of 16 MB, 32 MB, 64 MB or
128 MB. The card can be used with a variety of digital I/O
(input/output) products: digital music players, cellular
phones, PDAs, digital cameras, and digital video camcorders.

The SD card indicator flashes when the drive is in use.

The i.LINK
transfers of large quantities of data between the computer and
an external device, such as a video camera.

i.LINK® Port

PC Card eject buttons

®

port, also known as the IEEE 1394 port, allows

SD® card indicator

PC Card slots

The USB port lets you connect a USB peripheral to your
computer.

Left side

Finding Your Way Around

Left side

33

Line In jack

Wireless antenna indicator

Wireless antenna on/off switch*

Security lock slot

Microphone jack
Headphone jack

Volume
Control Dial

Speaker

* functional only on systems with a

wireless module installed

The 3.5 mm headphone jack lets you connect stereo
headphones or other audio-output devices, such as external
speakers. Connecting other devices automatically disables the
internal speakers.

The 3.5 mm microphone jack lets you connect an external
monaural microphone or other audio input device.

The line in jack lets you connect a DVD or CD player,
cassette tape player, or record player to your computer.

The volume control lets you adjust the sound on your
computer. To turn the volume up, turn the dial to the right. To
turn the volume down, turn the dial to the left.

The security lock slot allows you to attach an optional
PORT- Noteworthy

®

computer lock cable to your computer

for securing it to a large, heavy object such as your desk.

On those systems with Wi-Fi

TM

, the wireless antenna on/off

switch turns the computer’s wireless antenna on or off. The
Wi-Fi Mini PCI module is optional.

On those systems with Wi-Fi

TM

, the wireless antenna

indicator glows amber when the computer’s wireless antenna
is on.

Finding Your Way Around

34

Front with the display open

Front with the display open

Screen

Internet Button

Power button

Function keys

Keyboard

Palm rest
Primary
button

CD/DVD control buttons

The computer’s screen is a liquid crystal display (LCD) that
provides clear, sharp images. For more information about
viewing options, see “Exploring video features” on page 157.

On

The power button turns the computer on and off. Holding
down the power button for four seconds resets the computer.

The Internet button launches your default Internet browser.

The TOSHIBA Console button allows quick access to
various functions.

TOSHBIA Console
Button

One Touch TV
Out Button

To uc hP ad

Secondary
button

System
indicator panel

Finding Your Way Around

Front with the display open

The One Touch TV out button activates an external display
device such as a TV when connected to the video/audio line
out jack.

The 85-key keyboard provides all the functionality of a full­size keyboard. For more information, see “Using the

keyboard” on page 70.

35

The function keys, when used with the
several different system functions. For more information, see

“Hot Keys” on page 215.

The system indicator panel provides information about
various system functions.

The TouchPad
stroke of a finger.

The primary and secondary buttons below the TouchPad
act like the buttons on a mouse, with primary and secondary
functions.

The front panel provides a palm rest to assist you in
maintaining proper posture while using the computer.

The CD/DVD control buttons let you play audio CDs when
the computer is turned off. You can also use them to play CDs
and DVDs with the computer turned on. For more
information, see “CD/DVD control buttons” on page 78.

The stereo speakers let you hear sounds, such as system
alarms associated with your software, and music from DVD­ROMs and audio CDs.

TM

enables you to move the cursor with the

Fn key, activate

Finding Your Way Around

36

Front with the display open

Indicator lights

CD

Mode

Digital

Digital
Mode

AC Power

DC In

Battery

Hard

Drive

The CD mode light goes on in CD mode when the computer
is playing a CD with the computer off.

The digital mode light goes on in digital mode, when the
computer is playing a CD or DVD with the computer on.

The CD In light glows green when the computer is on. The
light blinks when the computer is in Standby mode.

The main battery light indicates the main battery’s current
charge. It glows green when the battery is fully charged. It
glows amber while the battery is being charged. It does not
glow if the external power source is disconnected or if the
battery is completely discharged. For more information on
determining remaining battery power, see “Monitoring

battery power” on page 101.

Disc/Disk

Activity

The hard disk drive light flashes while the hard disk drive is
being accessed.

The disc/disk activity light flashes when the Modular Bay
drive is being accessed.

The caps lock light glows when you press the

Caps Lock key.

When this light is on, pressing a letter key on the keyboard
produces an uppercase (capital) letter.

The cursor control mode light glows when the cursor
control overlay is on. When this light is on, pressing an
overlay key moves the cursor in the direction of the white
arrow printed on the key instead of typing the letter printed
on the top of the key. For more information, see “Using the

cursor control overlay” on page 73.

The numeric mode light glows when the numeric overlay is
on. When this light is on, pressing an overlay key types the
white number printed on the key instead of typing the letter
printed on the top of the key. For more information, see

“Using the numeric keypad overlay” on page 73.

CAUTION: Never turn off the computer while any drive is in use.
Doing so may damage the media and result in loss of data.

Underside

Finding Your Way Around

Underside

37

Modular Bay
release latch

Modular Bay

Memory slot
cover

Battery release
latch

Battery pack

38

Finding Your Way Around

Underside

The Modular Bay lets you use one of several possible
Modular Bay optical drive modules. A DVD-ROM drive is
shown in place. For more information, see “Using the

Modular Bay” on page 162.

The expansion memory slot cover protects the two
expansion memory slots where you insert additional memory.
See for detailed information.

The hard disk drive is the computer’s permanent data
storage device.

CAUTION: To prevent possible CPU overheating, do not block the
cooling vents when the computer is in use.

The battery pack contains the battery. For information about
replacing the battery, see “Changing the main battery” on

page 105.

The battery release latch secures the battery cover to the
computer, preventing the cover from dislodging from the
computer case.

Chapter 2

Getting Started

This chapter provides tips for working comfortably, describes
how to connect components, and explains what to do the first
time you use your notebook computer.

Selecting a place to work

Your computer is portable and designed to be used in a
variety of circumstances and locations.

Creating a computer-friendly environment

Place the computer on a flat surface which is large enough for
the computer and any other items you need to use, such as a
printer. Leave enough space around the computer and other
equipment to provide adequate ventilation and prevent
overheating.

To keep your computer in prime operating condition, protect
your work area from:

❖ Dust, moisture, and direct sunlight.

39

Getting Started

40

Selecting a place to work

❖ Equipment that generates a strong electromagnetic field,

such as stereo speakers (other than speakers that are
connected to the computer) or speakerphones.

❖ Rapid changes in temperature or humidity and sources of

temperature change such as air conditioner vents or
heaters.

❖ Extreme heat, cold, or humidity.

❖ Liquids and corrosive chemicals.

CAUTION: If you spill liquid into the computer, turn it off, unplug it
from the AC power source, and let it dry out completely before
turning it on again.

If the computer does not operate correctly after you turn it back on,
contact a Toshiba authorized service provider.

Keeping yourself comfortable

Strain and stress injuries are becoming more common as
people spend more time using their computers. With a little
care and proper use of the equipment, you can work
comfortably throughout the day.

This section provides hints on avoiding strain and stress
injuries. For more information, consult books on ergonomics,
repetitive-strain injury, and repetitive-stress syndrome.

Placement of the computer

Proper placement of the computer and external devices is
important to avoid stress-related injuries.

❖ Place the computer on a flat surface at a comfortable

height and distance. You should be able to type without
twisting your torso or neck, and look at the screen
without slouching.

Getting Started

Selecting a place to work

❖ If you are using an external monitor, the top of the

display should be no higher than eye level.

❖ If you use a paper holder, set it at about the same height

and distance as the screen.

41

Seating and posture

When using your computer, maintain good posture with your
body relaxed and your weight distributed evenly. Proper
seating is a primary factor in reducing work strain. Some
people find a backless chair more comfortable than a
conventional chair.

Below eye level

Approximately
90-degree angles

Footrest

Correct posture and positioning of the computer

Whichever type you choose, use the following guidelines to
adjust your chair for maximum computing comfort.

❖ Position your chair so that the keyboard is at or slightly

below the level of your elbow. You should be able to type
comfortably with your shoulders relaxed and your
forearms parallel to the floor.

If you are using a conventional chair:

❖ Your knees should be slightly higher than your hips. If

necessary, use a footrest to raise the level of your knees
and ease the pressure on the back of your thighs.

42

Getting Started

Selecting a place to work

❖ Adjust the back of your chair so that it supports the lower

curve of your spine. If necessary, use a cushion to provide
extra back support. Lower-back-support cushions are
available at many office supply stores.

❖ Sit with your back straight so that your knees, hips, and

elbows form approximately 90-degree angles when you
work. Do not slump forward or lean back too far.

Lighting

Proper lighting can improve the visibility of the display and
reduce eyestrain.

❖ Position the display panel or external monitor so that

sunlight or bright indoor lighting does not reflect off the
screen. Use tinted windows or shades to reduce glare.

❖ Avoid placing your computer in front of a bright light that

could shine directly in your eyes.

❖ If possible, use soft, indirect lighting in your computer

work area.

Arms and wrists

❖ Avoid bending, arching, or twisting your wrists. Keep

them in a relaxed, neutral position while typing.

❖ Exercise your hands, wrists, and arms to improve

circulation.

WARNING: Using the computer keyboard incorrectly may result in
discomfort and possible injury. If your hands, wrists, and/or arms
bother you while typing, stop using the computer and rest. If the
discomfort persists, consult a physician.

Work habits

The key to avoiding discomfort or injury from strain is to
vary your activities. If possible, schedule a variety of tasks
into your working day. Finding ways to break up the routine
can reduce stress and improve your efficiency.

❖ Take frequent breaks to change position, stretch your

❖ Avoid performing repetitive activities for long periods.

❖ Focusing your eyes on your computer screen for long

Precautions

Getting Started

Selecting a place to work

muscles, and relieve your eyes. A break of two or three
minutes every half hour is more effective than a long
break after several hours.

Intersperse such activities with other tasks.

periods can cause eyestrain. Look away from the
computer frequently and focus your eyes on a distant
object for at least 30 seconds.

43

Your notebook computer is designed to provide optimum
safety and ease of use, and to withstand the rigors of travel.
You should observe certain precautions to further reduce the
risk of personal injury or damage to the computer.

❖ Avoid prolonged physical contact with the underside of

the computer.

If the computer is used for long periods, its case can
become very warm. While the temperature may not feel
too hot to the touch, if you maintain physical contact with
the computer for a long time (if you rest the computer on
your lap, for example), your skin might suffer low-heat
injury.

❖ Never apply heavy pressure to the computer or subject it

to sharp impacts. Excessive pressure or impact can
damage computer components or otherwise cause your
computer to malfunction.

44

Getting Started

Selecting a place to work

❖ Some PC Cards can become hot with prolonged use. If

two cards are installed, both can become hot even if only
one is being used. Overheating of a PC Card can result in
errors or instability in its operation.

Be careful when you remove a PC Card that has been
used for a long period.

❖ Avoid spilling liquids into the computer’s keyboard.

If you do spill a liquid that gets into the keyboard, turn
off the computer immediately. Leave the computer turned
off overnight to let it dry out before you use it again.

❖ Never turn off the computer if a drive light indicates a

drive is active.

Turning off the computer while it is reading from or
writing to a disk may damage the disk, the drive, or both.

❖ Keep the computer and disks away from objects that

generate strong magnetic fields, such as large stereo
speakers.

Information on disks is stored magnetically. Placing a
magnet too close to a disk can erase important files.

❖ Scan all new files for viruses.

This precaution is especially important for files you
receive via email or download from the Internet.
Occasionally, even new programs you buy from a
supplier may contain a computer virus. You’ll need a
special program to check for viruses. Ask your dealer to
help you.

Setting up your computer

Setting up your computer

TECHNICAL NOTE: You must complete all set up steps up to

“Setting up your software” on page 45 before adding external or

internal components to your computer. These components
include, but are not limited to, a mouse, keyboard, printer,
memory, and PC cards.

Your computer contains a rechargeable high-capacity battery
that needs to be charged before you can use it.

To use external power or to charge the battery, you must
attach the AC adapter. See Connecting the AC adapter for
more information.

Setting up your software

The first time you turn on your computer, the Setup Wizard
guides you through steps to set up your software.

Getting Started

45

1 From the welcome screen, click Next to enter the Setup

Wizard.

2 Confirm acceptance of Microsoft’s End User License

Agreement and click Next.

3 Enter the computer name and description and click Next

or Skip.

The computer will pause for a moment while checking
for an internet connection, and you will see the screen
“Checking your internet connectivity.”

A window will display the message: “How will this
computer connect to the internet?” The system displays
three selections: Telephone modem, Digital subscriber
line (DSL) or cable, or Local Area Network (LAN).

46

Getting Started

Setting up your computer

4 Click Skip to exit the process or Next to continue.

NOTE: To register online, your computer’s modem must have an
Internet connection.

A window will display asking if you wish to register with
Toshiba and Microsoft.

5 Click Ye s to register, or No to exit the process.

NOTE: If you click No, you may register with Toshiba by clicking
the Register with Toshiba icon on the desktop.

6 If you selected Yes in step 5, enter your personal

information in the registration window.

A window will display the message, “Who will use this
computer?”

7 Enter your name and click Next to complete the process.

A window will display the message, “Thank you.”

8 Click Finish to continue.

Your computer restarts automatically.

Getting Started

Setting up your computer

Registering your computer with Toshiba

Registering your computer lets Toshiba keep you up-to-date
with information about new products and upgrades, and also
extends your Toshiba warranty worldwide at no charge to
you. You can register your computer with Toshiba during the
start-up process or by clicking on the icon on the desktop at a
later time.

NOTE: To register online, your computer’s modem must be
connected to a voice-grade telephone line.

Adding external devices

NOTE: Before adding external devices, Toshiba recommends
setting up your software first. See “Setting up your software” on

page 45.

47

Before starting to use your computer, you may also want to:

❖ Add more memory (see “Installing additional memory

(optional)” on page 54)

❖ Connect a mouse (see “Connecting a mouse” on page 60)

❖ Connect a local printer (see “Connecting a printer” on

page 61)

❖ Install PC Cards (see “Using PC Cards” on page 164)

Getting Started

48

Connecting the AC adapter

Connecting the AC adapter

Your computer requires power to operate. Use the power
cable and AC adapter to connect the computer to a live
electrical outlet, or to charge the computer’s battery.

AC power
indicator

Power cable

Power cable and AC adapter

CAUTION: Use only the AC adapter supplied with your computer
or an equivalent adapter that is compatible. Use of any
incompatible adapter could damage your computer. Toshiba
assumes no liability for any damage caused by use of an
incompatible adapter.

AC adapter

When you connect the AC adapter to the computer, always follow
the steps in the exact order as described in the User's Manual.
Connecting the power cable to a live electrical outlet should be the
last step otherwise the adapter DC output plug could hold an
electrical charge and cause an electrical shock or minor bodily
injury when touched. As a general safety precaution, avoid
touching any metal parts.

DANGER: Hold the power cable by its plug when you connect/
disconnect it. Do NOT pull the cable itself. Doing so may damage
the power cable and result in a short circuit or electric shock.

Getting Started

Connecting the AC adapter

To connect AC power to the computer:

1 Connect the power cable to the AC adapter.

Connecting the power cable to the AC adapter

2 Plug the AC adapter into the DC-IN on the back of the

computer.

49

Connecting the AC adapter to the computer

3 Connect the power cable to a live electrical outlet.

The AC power and battery lights glow.

DANGER: Damaged power cables can cause fire or electric shock.
Never modify, forcibly bend, place heavy objects on top of, or
apply heat to the power cable.

If the power cable becomes damaged or the plug overheats, dis­continue use. There is a risk of electric shock.

Never remove the power plug from the outlet with wet hands.
Doing so may cause an electric shock.

Getting Started

50

Charging the main battery

Charging the main battery

To charge the main battery, plug the computer into a live wall
outlet. It takes several hours to charge the battery with the
computer off. It takes much longer to charge the battery while
the computer is on. For more information on battery use, see

“Running the computer on battery power” on page 98.

TECHNICAL NOTE: The battery does not charge while the
computer is consuming full power.

CAUTION: Once the battery is charged for the first time, avoid
leaving the computer plugged in and turned off for more than a few
hours at a time. Continuing to charge a fully charged battery can
damage the battery.

NOTE: Battery life and charge time may vary depending on the
applications, power management settings, and features used.

Getting Started

Using the computer for the first time

Using the computer for the first time

Opening the display panel

Press the display latch and lift the display panel.

Lift

Slide

Opening the display panel

CAUTION: To avoid damaging the display panel, don’t force it
beyond the point where it moves easily.

51

Never lift or move the computer using the display panel.

Turning on the power

1 Check that any drives on the computer are empty.

On

2 Turn on the computer by pressing and releasing the

power button located on the top of the keyboard. For an
illustration to help you locate this button, see “Front with

the display open” on page 34.

NOTE: When you turn on the computer for the first time, don’t turn
off the power again until the operating system has loaded
completely.

52

Getting Started

Using the computer for the first time

The AC power indicator glows when the computer is
connected to an external power source.

The battery light:

❖ Glows amber while the battery is being charged.

❖ Glows green when the battery is fully charged.

❖ Is unlit when the computer is not connected to an

external power source. For information on
determining battery power, see “Monitoring battery

power” on page 101.

The hard disk drive indicator flashes to indicate that the
hard disk drive is currently in use.

The disc/disk activity indicator flashes while the Modular
Bay is being accessed.

CAUTION: Never turn off the computer while any drive is in use.

Using the TouchPad

The TouchPad, the small, smooth square cutout located in
front of the keyboard, is sensitive to touch and enables you to
move the cursor with the stroke of a finger. Simply move
your finger on the TouchPad in the direction you’d like to
move the cursor:

❖ To move the cursor to the top of the page, push your

finger forward on the TouchPad.

❖ To move the cursor to the bottom of the page, drag your

finger toward yourself.

❖ To move the cursor to the right side of the page, slide

your finger across the TouchPad from left to right.

™

❖ To move it to the left side, slide your finger from right to

left.

NOTE: Because the TouchPad is much smaller than the display
screen, moving your cursor across the screen often means having
to move your finger several times across the TouchPad in the
preferred direction.

Once you’ve positioned your cursor, you can either click it
into place by double-tapping the TouchPad or clicking the
control buttons. For more on the TouchPad, see “Lesson 2:

Using the TouchPad and control buttons together” on
page 115.

Control buttons

When a step instructs you to click or choose an item, move
the cursor to the item, then press and release the primary
(left-hand) button. To double-click, press the primary button
twice in rapid succession. The primary button usually
corresponds to the left mouse button.

Getting Started

Using the computer for the first time

53

The function of the secondary (right-hand) button depends on
the program you are using. It usually corresponds to the right
mouse button. Check your program’s documentation to find
whether it uses the right mouse button.

Disabling or enabling the TouchPad

The TouchPad is enabled by default. To change the enable/
disable TouchPad setting:

1 Click Start, Control Panel.

The Control Panel window appears.

2 Click Printers and Other Hardware.

3 Click Mouse or press the Fn + F9 hot keys.

The Mouse Properties window appears.

Getting Started

54

Installing additional memory (optional)

4 Click the TouchPAD ON/OFF tab.

The TouchPAD ON/OFF tab view window appears.

5 Select Disable or Enable, whichever is appropriate.

6 Click Apply.

7 Click OK.

The Mouse Properties window closes.

8 Close the Printers and Other Hardware window.

9 Close the Control Panel window.

NOTE: The Fn + F9 shortcut can be used to enable or disable the
TouchPad (see “Hot Keys” on page 215).

Installing additional memory (optional)

CAUTION: Before you install or remove a memory module, turn off
the computer using the Start menu. If you install or remove a
memory module while the computer is in Stand by or Hibernation
mode, data will be lost.

A memory module must be installed in slot A. Do not try to oper­ate the computer with a memory module in slot B only.

If you install a memory module that is incompatible with the
computer, a beep will sound when you turn on the computer. If the
module is installed in slot A, there will be a long beep followed by
a short beep. If the module is in slot B, there will be a long beep
followed by two short beeps. In this case, turn off the computer
and remove the incompatible module.

Getting Started

Installing additional memory (optional)

Your computer comes with enough memory to run most of
today’s popular applications. You may want to increase the
computer’s memory if you use complex software or process
large amounts of data.

Additional memory comes in various capacities (visit
Toshiba’s website at toshiba.com for more information).
There are two memory slots. Your system may have both
slots occupied.

CAUTION: If you use the computer for a long time, the memory
modules will become hot. If this happens, let the modules cool to
room temperature before you replace them.

You need a standard Phillips no. 1 screwdriver to install a
memory module.

CAUTION: To avoid damaging the computer’s screws, use a
standard Phillips no. 1 screwdriver that is in good condition.

55

If you are adding memory after you have started to use the
computer, begin at step 1, otherwise skip to step 2.

1 Turn off the computer via the Start menu.

See “Using Turn Off or Shut down” on page 88.

The operating system turns off the computer.

2 Unplug and remove any cables connected to the

computer.

3 Close the display panel and turn the computer upside

down to locate the expansion memory slot cover.

56

Getting Started

Installing additional memory (optional)

Memory slot cover

Base of a Satellite 2430/2435 computer

4 Using a standard Phillips no. 1 screwdriver, unscrew the

two screws that secure the expansion memory slot cover,
then remove the memory slot cover.

Removing the memory slot cover

Getting Started

Installing additional memory (optional)

5 Put the screws and the cover in a safe place so that you

can retrieve them later.

CAUTION: Static electricity can damage the memory module.
Before you handle the module, touch a grounded metal surface to
discharge any static electricity you may have built up.

To avoid damaging the memory module, be careful not to touch its
gold connector bar (on the side you insert into the computer).

6 The memory enclosure shares its space with an optional

Wi-Fi Mini PCI module. If there is no Wi-Fi module
installed, proceed to step 7. Otherwise:

Release the white antenna wire from the Main connector
on the module. Then remove the black antenna wire from
the Aux connector.

57

Removing the antenna wires

Unclip one of the sides securing the Wi-Fi module and
gently remove it from the connector.

Remove the Wi-Fi module from the compartment to gain
access to the memory module connectors.

58

Getting Started

Installing additional memory (optional)

The following figure shows the inside of the memory
compartment.

Viewing the inside of the memory compartment

7 Remove the memory module from its antistatic

packaging.

8 Holding the memory module by its edges so that the gold

connector bar faces the slot, fit the module into the
socket.

9 Gently put the memory module connector down at an

angle and press down until the clips snap into place.

Do not force the module into position. The memory
module should be level when secured in place.

Inserting the memory module

CAUTION: Avoid touching the connectors on the memory module
or on the computer. Grease or dust on the connectors may cause
memory access problems.

Getting Started

Installing additional memory (optional)

10 If you removed the Wi-Fi module, reinstall it by reversing

the steps in step 6 and referring to the following figures.

Replacing the Optional Wi-Fi Module and reconnecting the
antenna wires

11 Replace the expansion memory slot cover.

12 Replace the screws and tighten them.

13 Turn the computer over and reconnect any cables you

removed.

14 Turn on the computer.

59

To verify that the computer correctly recognizes the
memory, click Start, Control Panel and click
Performance and Maintenance. Click System to view
the recognized memory.

15 If the computer does not recognize the memory, shut

down the computer, remove the memory slot cover, and
make sure the memory module is seated properly, as
described in step 8.

Getting Started

60

Installing additional memory (optional)

Removing a memory module

1 Follow steps 1 through 6 in “Installing additional

memory (optional)” on page 54.

2 Gently push the memory locks outward until the memory

module pops up.

Removing the memory module

3 Gently pull the memory module diagonally to pull it out

of the slot.

4 Complete the procedure by following steps 10 through 12

in “Installing additional memory (optional)” on page 54.

Connecting a mouse

You may want to use a mouse instead of the TouchPad, the
computer’s built-in pointing device.

To connect a USB mouse, plug the mouse cable into one of
the USB ports.

Connecting a printer

NOTE: Read the documentation that came with your printer. Follow
the manufacturer’s instructions when connecting a local printer.

NOTE: You must supply the proper printer cable. If one did not
come with your printer, you may purchase one from an electronics
or computer store.

If your printer is ECP- or IEEE-compliant, make sure your printer
cable is an IEEE 1284 cable.

CAUTION: Your printer documentation may require you to install
the printer software before physically connecting the printer to
your computer. If you do not install the software as instructed by
the printer manufacturer, the printer may not function correctly.

Getting Started

Installing additional memory (optional)

61

CAUTION: Never connect the printer cable while the computer’s
power is on. Doing so may damage the printer, the computer, or
both.

You can connect a USB-compatible printer to your computer
through the USB ports. To determine if the printer is USB­compatible, check its documentation.

To achieve the connection, you need a suitable USB cable,
which may come with your printer. You can purchase one
from a computer or electronics store.

To connect a USB printer:

1 Plug the USB connector into one of the USB ports on

your computer

62

Getting Started

Installing additional memory (optional)

2 Plug the printer’s power cable into a live AC outlet.

To connect a parallel printer:

CAUTION: Connecting the parallel printer cable while the
computer is on may damage the printer, the computer, or both.

1 Connect the printer cable to the printer and to the

computer’s parallel port.

To the computer

Identifying the ends of a parallel printer cable

2 Plug the printer’s power cable into a live AC outlet.

See your printer documentation for additional configuration
steps, or see “Setting up a printer,” below.

Setting up a printer

If you started your computer with a printer connected and
turned on, it may have been detected automatically (Plug and
Play). If this is not the case, then you must install the printer
driver for the model of printer that is connected to your
computer. You install the printer driver either by following
the instructions indicated in your printer manual, or by using
the operating system Add Printer Wizard.

If you plan to set up a printer later, click Cancel.

Using the Add Printer Wizard

To set up a printer with the Add Printer Wizard:

1 Click Start, Control Panel, then Printers and Other

Hardware.

To the printer

2 Select Printers and Faxes.

Installing additional memory (optional)

The Printers and Faxes window appears.

Sample Printers and Faxes window

3 Click Add Printer.

Getting Started

63

The Add Printer Wizard starts.

Sample Add Printer Wizard

64

Getting Started

Installing additional memory (optional)

4 Click Next.

The Add Printer Wizard asks you to select your printer.

TECHNICAL NOTE: If your printer is Plug and Play, the operating
system recognizes it automatically. You can ignore the remainder
of this section. See your printer manual.

5 If the printer you are setting up:

❖ Is not connected to a network, select Local printer

attached to this computer.

If you select Local printer, check “Automatically detect
and install my Plug and Play printer.”

❖ Is connected to a network, select Network printer,

or a printer attached to another computer.

6 Click Next.

The Add Printer Wizard prompts you to select your
printer.

7 From the list of manufacturers and printers, select your

printer, then click Next.

8 Select the port settings according to the instructions in

your printer’s documentation and the port to which your
printer is connected, then click Next.

The Add Printer Wizard prompts you to enter a printer
name.

9 Enter a name for your printer.

HINT: If you are using more than one printer, make sure the name
is descriptive enough to help you tell the difference.

10 To set up the printer to be the default printer for the

operating system, click Ye s .

11 Click Next.

The operating system prompts you to print a test page.

12 If your printer is connected and turned on, click Next.

To complete the setup procedure without printing a test
page, click No, then click Next.

13 Click Finish.

You are now ready to print.

Depending on your program, you may see various
messages indicating the status of your print job.

Turning off the computer

It is a good idea to turn off your computer when you are not
using it for a while.

If you are using the computer for the first time, leave the
computer plugged into a power source (even though the
computer is off) to fully charge the main battery. With the
computer off, it may take up to three hours to recharge the
main battery.

Getting Started

Turning off the computer

65

When you power down the computer, you have three options
to choose from: Turn Off (or Shut down), Hibernate and
Standby. Each option has its advantages.

❖ Use the Turn Off command if you are using the

Windows
Windows
connected to a domain server.

❖ Use the Shut down command if you are using the

Windows
connected to a domain server.

❖ If you have work in progress and are not connected to a

network, use the Windows
commands to save your system settings to memory so
that, when you turn on the computer again, you will
automatically return to where you left off.

®

XP Home version operating system, or the

®

XP Professional operating system when not

®

XP Professional operating system and

®

Standby or Hibernate

66

Getting Started

Caring for your computer

❖ To leave the computer off for a longer period, you can use

the Windows
a domain server or the Shut down when connected to a
domain server instead.

CAUTION: Never turn off the computer while any drive is in use.
Doing so may damage the media in use and result in loss of data.

For more information, see “Powering down the computer” on

page 87.

®

Turn Off command when not connected to

Caring for your computer

This section gives tips on cleaning and moving your
computer, and explains how to fit an antitheft lock. For
information about taking care of your computer’s battery, see

“Running the computer on battery power” on page 98.

Cleaning the computer

To keep your computer clean, gently wipe the display panel
and exterior case with a lightly dampened cloth. Ask your
Toshiba dealer for suggestions for appropriate cleaning
products.

CAUTION: Keep liquid, including cleaning fluid, out of the
computer’s keyboard, speaker grille, and other openings. Never
spray cleaner directly onto the computer. Never use harsh or
caustic chemical products to clean the computer.

Moving the computer

Before moving your computer, even across the room, make
sure all disk activity has ended (the disk activity lights stop
glowing) and all external peripheral cables are disconnected.

CAUTION: Never pick up the computer by its display panel or by
the back (where the ports are located).

Although your notebook computer is built to withstand
reasonable shock and vibration, transport it in a carrying case
for long trips. You can purchase a carrying case from your
Toshiba dealer or visit Toshiba’s Web site at

Using a computer lock

You may want to secure your computer to a heavy object such
as your desk. The easiest way to do this is to purchase an
optional PORT-Noteworthy

Getting Started

Caring for your computer

toshiba.com.

®

computer lock cable.

67

®

PORT-Noteworthy

To secure the computer:

1 Loop the cable through or around some part of a heavy

object.

Make sure there is no way for a potential thief to slip the
cable off the object.

2 Pass the locking end through the loop.

3 Insert the cable’s locking end into the security lock slot,

then rotate the key a quarter turn and remove it.

computer lock cable

68

Getting Started

Caring for your computer

The computer is now securely locked to deter computer
theft.

Locking the computer

Chapter 3

Learning the Basics

This chapter lists some computing tips and provides
important information about basic features.

Computing tips

❖ Save your work frequently.

Your work temporarily stays in the computer’s memory
until you save it to the disk. You will lose all unsaved
work, if, for example, a system error occurs and you must
restart your computer, or your battery runs out of charge
while you are working. Your computer can be configured
to warn you when the battery is running low. See “Power

management” on page 99.

HINT: Some programs have an automatic save feature which you
can turn on. This feature saves your file to the hard disk at preset
intervals. See your software documentation for details.

69

70

Learning the Basics

Using the keyboard

❖ Back up your files to storage media on a regular basis.

Label the backup copies clearly and store them in a safe
place.

If your hard disk suddenly fails, you may lose all the data
on it unless you have a separate backup copy.

❖ Use Error-Checking and Disk Defragmenter regularly to

conserve disk space and help your computer perform at
its optimal level. Consult your Windows

®

XP operating
system documentation for more information on these and
other utilities.

❖ Always use the proper procedure to turn off the

computer. (See “Powering down the computer” on

page 87.)

CAUTION: The operating system records information, such as
your desktop setup, during its shut down procedure. If you don’t
let the operating system shut down normally, details such as new
icon positions may be lost.

Using the keyboard

Keyboard

Home

7

4

End PgDn

PgUp

9

8

1

Ins

0

∗

-

6

5

+

3

2

Del

End

/

Character keys

Typing with the character keys is very much like typing on a
typewriter, except that:

❖ The spacebar creates a space character instead of just

passing over an area of the page.

❖ The lowercase l (el) and the number 1 are not

interchangeable.

❖ The uppercase letter O and the number 0 are not

interchangeable.

❖ The Caps Lock key changes only the alphabet keys to upper

case — the number and symbol keys are not affected.
The caps lock light on the keyboard indicator panel
illuminates when you press the

Ctrl, Fn, and Alt keys

Alt

Fn

Ctrl

Ctrl, Fn and Alt keys

Learning the Basics

Using the keyboard

Caps Lock key.

71

.

Ctrl, Fn, and Alt keys do different things depending on the

The
program you are using. For more information, see your
program documentation.

Function keys

The function keys (not to be confused with the Fn key) are the
12 keys at the top of the keyboard.

Function keys

F1 through F12 are called function keys because they run

programmed functions when you press them. Used in
combination with the
run specific functions on the computer.

Fn key, function keys marked with icons

Learning the Basics

72

Using the keyboard

Windows® special keys

Windows® special keys

The keyboard provides two keys that have special functions
in the operating system:

❖ The Windows

❖ The Application key has the same function as the

secondary TouchPad control button (or secondary mouse
button).

Overlay keys

790

Home PgUp

78 9

UIOP

Application key

Windows logo key

®

logo key opens the Start menu.

()&

∗

8

456

JKL

End PgDn

123

M

Ins Del

0

∗

-

:
;

+

>

?

.

/

.

/

End

Keyboard overlay keys

The keys with numbers and symbols on the front of them
form the numeric and cursor overlay. This overlay lets you
enter numeric data or control the cursor as you would using
the ten-key keypad on a desktop computer’s keyboard.

Learning the Basics

Using the keyboard

73

Using the numeric keypad overlay

To turn on the numeric keypad overlay, press Fn and F11
simultaneously. The numeric mode light on the keyboard
indicator panel glows when the numeric overlay is on.

You can still use the overlay keys to type alphabetic
characters while the numeric overlay is on. To do so:

❖ For lowercase letters, hold down Fn while you type the

letters.

❖ For uppercase letters, hold down both Fn and Shift while

you type the letters.

To use the cursor control overlay when the numeric overlay is
on, press and hold down
keys. To return to the numeric overlay, release

Shift while you use the cursor control

Shift.

To turn off the numeric keypad overlay, hold down the
and press
indicator panel goes out.

F11 again. The numeric mode light on the keyboard

Fn key

Using the cursor control overlay

To turn on the cursor control overlay, press Fn and F10
simultaneously. The cursor control mode light on the
keyboard indicator panel glows when the cursor control
overlay is on.

To type alphabetic characters while the overlay is on:

❖ For lowercase letters, hold down Fn while you type the

letters.

❖ For uppercase letters, hold down both Fn and Shift while

you type the letters.

To use the numeric keypad overlay when the cursor control
overlay is on, hold down
overlay keys. To return to the cursor control overlay, release

Shift.

Shift while you use the numeric

Learning the Basics

74

Starting a program

To turn off the cursor control overlay, hold down the Fn key
and press
keyboard indicator panel goes out.

F10 again. The cursor control mode light on the

Starting a program

The easiest way to start a program is to double-click the name
of the file that contains the information you want to work on.
To find the file, use My Computer or Windows Explorer.

If you prefer to open the program first, you have four options:

❖ Double-click the icon for the program on your desktop

❖ Use the Start menu

❖ Use Windows Explorer to locate the program file

❖ Use the Run dialog box

The Windows
step-by-step instructions for starting a program from the Start
menu. See “Lesson 6: Starting programs” on page 121.

®

XP operating system tutorial chapter gives

Saving your work

Before you turn off the computer, save your work to the hard
disk drive.

NOTE: Always save your data even when you are using the Stand
by. If your battery fully discharges, your information will be lost.
Your computer can be configured to warn you when the battery is
running low, see “Power management” on page 99.

Many programs offer a feature that saves documents at
regular intervals, such as every 15 minutes. Check your
programs’ documentation to see whether they have an
automatic save feature.

To save :

❖ A file you are updating, open the program’s File menu

and click Save.

❖ A new file, choose Save As from the File menu, type a

name for the file, and click OK.

HINT: To make another copy of the file you are currently working
with, choose Save As from the File menu and give the new file a
different name.

For information on how to name a file, see “Windows

file system” on page 114.

Printing your work

Verify that the Windows® XP operating system is set up for
your printer as described in “Setting up a printer” on page 62.

Learning the Basics

Printing your work

®

XP

75

TECHNICAL NOTE: You only need to set up the printer the first
time you connect it. If you use more than one printer or are
changing printers, you will need to set up the operating system to
run with the additional printer(s).

To print a file:

1 If your printer is not on, turn it on now.

2 In the File menu of your program, click Print.

The program displays a Print dialog box.

3 Click OK to print.

Learning the Basics

76

Backing up your files

Backing up your files

Backing up your files means copying individual files to
media, such as CD, or copying entire sections of your hard
disk to another device, such as a tape drive.

For those systems with a floppy disk drive, you may back up
file to a floppy disk as follows:

1 To back up to a CD or other media, insert the media into

the diskette appropriate drive.

2 Click Start, then click My Computer.

3 Click the drive that contains the file you want to copy.

4 Double-click the folder that contains the file, then click

the file you want to copy.

HINT: You can use the Ctrl or Shift keys to select more than one
file.

5 Click File, then click Send To.

Using the DVD-ROM or Multifunction drive

Optical storage has become the preferred medium for
software, music, and video. Digital versatile discs (DVDs)
provide a significant increase in data storage and support
features that are not available on any other video platform.
These features include wide-screen movies, multiple
language tracks, digital surround sound, multiple camera
angles, and interactive menus.

For these reasons, your computer may come with a DVD­ROM.

If a DVD-ROM drive or Multifunction drive is not currently
installed in the Modular Bay, follow the instructions in

“Using the Modular Bay” on page 162.

Learning the Basics

Using the DVD-ROM or Multifunction drive

drive or Multifunction drive.

HINT: Your DVD-ROM or Multifunction drive is designed to play
region 1 (North America) DVD-ROMs.

NOTE: For optimum DVD performance, it is recommended that
you play DVDs while running the computer on AC power.

You use CD-ROMs to load and run software, and to access
reference material such as catalogs, as well as listen to music.
A special feature allows you to play audio CDs even when the
computer is turned off. For more information, see “CD/DVD
control buttons” on page 87.

Drive components and control buttons

77

The DVD-ROM or multifunction drive resides in the Modular
Bay on the bottom-right side of the computer. The CD/DVD
control buttons are located at the front edge of the computer
and can be accessed when the display panel is closed or open.

DVD-ROM drive components

Your DVD-ROM drive may look like this:

Eject button
Manual eject hole

Sample DVD-ROM drive

78

Learning the Basics

Using the DVD-ROM or Multifunction drive

CAUTION: Never press the eject button or turn off the computer
while the drive-in-use indicator light is glowing. Doing so could
damage the disc or the drive.

The eject button requires power to operate. The manual eject
button does not require power.

CAUTION: Never use a pencil to press the manual eject button.
Pencil lead can break off inside the computer and damage it.
Instead, use a slim object such as a straightened paper clip.

HINT: When the computer is off and the DVD-ROM drive is on,
press the stop/eject control button on the top of the computer to
eject a disc.

CD/DVD control buttons

The control buttons on the front edge of the computer let you
to play audio CDs when the computer is off. You can also use
them to play CDs and DVDs when the computer is on.

Mode button

Previous track

CD/DVD control buttons in front of the computer

The mode button switches between the CD/DVD and digital
audio modes. When you use this button to select a mode, the
CD or Digital Mode indicator lights to show the active mode.
You can lock the mode to its current setting by pressing and

Next track

Play/pause

Stop/eject

Learning the Basics

Using the DVD-ROM or Multifunction drive

holding the mode button for four seconds. When the mode
button is locked, you cannot switch between the CD/DVD
and digital audio modes. To unlock the mode button, press
and hold it for four seconds.

The previous track button returns to the preceding track on
the disc.

The next track button skips to the following track on the
disc.

The play/pause button starts playing the disc or makes it
pause if currently playing.

The stop/eject button stops a disc that is currently playing.

You can eject a disc by pressing the stop/eject button twice.
Use this method to eject a disc when the computer is turned
off and the sound subsystem is turned on.

CD/DVD control and digital audio modes

The following chart describes CD/DVD control and digital
audio mode.

79

Power is off and you
press Play/Pause

While in CD/DVD
mode, you press the
mode button

CD/DVD Mode Digital Audio Mode

If a CD is in the
drive, the system
enters CD player
mode and operates as
a stand-alone CD
player.

If a DVD is in the
drive, the operating
system starts and the
DVD player starts.

DVD-ROM drive
power turns off.

The operating sys­tem starts, the Media
Player starts and the
digital audio file
begins to play.

80

Learning the Basics

Using the DVD-ROM or Multifunction drive

CD/DVD Mode Digital Audio Mode

Power is off and you
press Play/Pause

Operating system is
running and you
press Play/Pause

Inserting a disc

If a CD is in the
drive, the system
enters CD player
mode and operates as
a stand-alone CD
player.

If a DVD is in the
drive, the operating
system starts and the
DVD player starts.

If a CD is in the
drive, the Media
Media Player starts
and the digital audio
file begins to play.

If a DVD is in the
drive, WinDVD starts
and the DVD begins
to play.

The operating sys­tem starts, the Media
Player starts and the
digital audio file
begins to play.

Media Player starts
and the digital audio
file begins to play.

WARNING: Before playing an audio CD, turn the volume down.
Playing the compact disc at maximum volume could damage your
ears. To turn the volume down, use the Volume Control switch or
access the Volume Control program (click Start, All Programs,
Accessories, Entertainment, Volume Control).

1 If the computer is turned on, press the eject button on the

DVD-ROM drive.

Learning the Basics

Using the DVD-ROM or Multifunction drive

The disc tray partially opens.

CAUTION: To avoid damaging a disc or losing data, check that the
disc activity light is off before opening the disc tray.

2 Grasp the disc tray and pull it fully open.

3 Hold the disc by its edges and check that it is clean and

free of dust.

CAUTION: Handle discs carefully. Avoid touching the surface of
the disc. Grasp it by its center hole and edge. If you handle the
disc incorrectly, you could lose data.

4 Carefully place the disc in the empty tray with its label

facing up.

81

Inserting a disc

CAUTION: Be careful not to touch the drive’s lens (located
underneath the drive’s spindle) or the area around it. Doing so
could cause the drive to malfunction.

82

Learning the Basics

Using the DVD-ROM or Multifunction drive

5 Gently press the center of the disc onto the spindle until it

locks into place.

Spindle

Disc

Positioning the disc on the spindle

CAUTION: Make sure the disc is properly positioned on the
spindle. If you position the disc incorrectly, it can jam the disc
tray.

6 Close the disc tray by pressing gently on the center of the

tray until it clicks indicating that it is locked.

Playing an audio CD

Insert an audio CD and close the disc tray.

The computer automatically detects a disc in the drive and
opens the Audio CD window. To play an audio CD select the
Play Audio CD using Windows Media Player option and
click OK.

Correct position

Incorrect position

Incorrect position

Sample Audio CD window

Learning the Basics

Using the DVD-ROM or Multifunction drive

The Windows Media Player window appears.

83

Rewind
Play

Stop
Previous track

Next track
Mute

Sample Windows Media

The Windows Media

TM

TM

Player control panel works much like

Fast forward

Volume control

Player screen

an ordinary compact disc player:

❖ To play the CD or to pause, click the Play/Pause button

on the CD Player control panel.

❖ To stop the CD, click the Stop button.

Learning the Basics

84

Using the DVD-ROM or Multifunction drive

Playing a DVD

This manual has an entire chapter devoted to using WinDVD.
For information about how to play back a DVD, see “Playing

DVDs” on page 167.

Viewing the contents of a CD or DVD

CDs and DVDs contain files just like the hard disk. CDs are
often used to install software or store files that require lots of
space, such as photographs and large presentation files. You
can use Explorer or My Computer to view the contents of any
CD or DVD.

Removing a disc with the computer on

CAUTION: Never press the eject button or turn off the computer
while the drive-in-use light is glowing. Doing so could damage
the disk or the drive.

1 Locate and press the eject button.

The disc tray partially opens.

2 Grasp the sides of the disc tray and pull it fully open.

3 Remove the disc from the disc tray and place it in its

protective cover.

CAUTION: If the disc is spinning when you open the disc tray, wait
for the disc to stop before removing it.

4 Close the disc tray by pressing gently on the center of the

tray until it clicks indicating that it is locked.

Learning the Basics

Using the DVD-ROM or Multifunction drive

Removing a disc with the computer off

1 Insert a slender object, such as a straightened paper clip,

into the manual eject button access hole.

CAUTION: Never use a pencil to press the manual eject button.
Pencil lead can break off inside the computer and damage it.

2 Pull the tray fully open, remove the disc and place it in its

protective cover.

3 Close the disc tray by pressing gently on the center of the

tray until it clicks indicating that it is locked.

Caring for CDs and DVDs

❖ Store your discs in their original containers to protect

them from scratches and keep them clean.

85

❖ Never bend a disc or place heavy objects on top of it.

❖ Hold a disc by its outside edge. Fingerprints on the

surface of a compact disc can prevent the drive from
reading the data properly.

❖ Avoid exposing discs to direct sunlight or extreme heat or

cold.

❖ To clean a disc, wipe it from the center outwards (not in a

circle) with a clean, dry cloth. If necessary, moisten the
cloth with water or a neutral cleaner (not benzine or
rubbing alcohol). Let the disc dry completely before
inserting it in the drive.

Learning the Basics

86

Setting up for communications

Setting up for communications

To communicate across the telephone lines with another
computer, you need:

❖ The computer’s modem

❖ A telephone line

❖ An Internet Service Provider (ISP)

To connect to the Internet, you need a Web browser, such as
Microsoft

®

Internet Explorer.

TECHNICAL NOTE: Disable Call Waiting before you connect
through the modem. Call Waiting may interrupt data transmission.

Connecting the modem to a phone line

Your computer comes with a built-in modem. To use the
modem, you must connect it to a standard voice-grade RJ-11
telephone line. For more information regarding your
computer’s modem, visit Toshiba’s web site at toshiba.com.

1 Attach one end of a standard RJ-11 telephone cable to the

modem port.

To locate the modem port, see “Back” on page 30.

2 Plug the other end of the RJ-11 telephone cable into the

modular jack of a standard voice-grade telephone line.

Connecting your computer to a network

You can connect your computer to a network remotely, using
the built-in modem and a dial-up connection. For specific
information about connecting to the local area network
(LAN) or wide area network (WAN), consult your network
administrator.

Learning the Basics

Powering down the computer

To use a dial-up connection, have your network administrator
configure your computer for the network and supply you with
the telephone number for the dial-up connection. To set up
the network connection, use the Dial-Up Networking Wizard:

1 Click Start and point to All Programs.

2 Point to Accessories, then to Communications.

3 Click Network Setup Wizard or Network

Connections.

4 Enter the phone number of your network connection and

let the program dial the number.

The computer connects with the network.

Powering down the computer

87

NOTE: Pushing the power button before shutting down the
Windows
Make sure the system indicator panel’s disk light and the drive-in­use light are off. If you turn off the power while a disk is being
accessed, you may lose data or damage the disk and/or drive.

When you power down the computer, you have three options
to choose from: Turn Off, Stand By, and Hibernation.

You can set the computer to turn on automatically at a time
you designate. This option is helpful for transferring files by
modem at night. You can set the computer to turn on and send

®

operating system could cause you to lose your work.

Learning the Basics

88

Using Turn Off or Shut down

or receive the files while you are asleep. This option is called
Auto Power On.

TECHNICAL NOTES: Before using any of these options to power
down your computer, save your files and make sure the disk
activity lights are off.

If you change your mind and decide to continue working after all,
wait a few seconds before turning the computer on again.

Using Turn Off or Shut down

For the Windows® XP Home operating system, follow these
steps to shut down the computer:

1 Click Start, select Turn off computer.

The Turn off computer dialog box appears.

Sample Turn off computer dialog box

2 Click Turn O ff .

The computer shuts down completely.

For the Windows
these steps to shut down the computer:

1 Click the Start button, then Shut down.

The Shut Down Windows dialog box appears.

®

XP Professional operating system, follow

2 Select Shut down from the drop-down list.

3 Click OK.

The computer shuts down completely.

NOTE: Holding the shift key while the Turn Off computer Windows
dialog box is open, changes the Stand By button to hibernate. For
more information about setting up hibernation “Hibernation

command” on page 89 and “Using Hibernation” on page 92.

Hibernation command

The Hibernation command shuts the computer down
completely, but it first saves the current state of the computer
to the hard disk. Since Hibernation mode does not require
power to maintain the saved information, the system settings
are retained indefinitely. Restoring information from the hard
disk takes longer than restoring it from memory. When you
start up again, the computer runs a self-test, loads the
operating system, and then returns to the state in which you
left it.

Learning the Basics

Using Turn Off or Shut down

89

Factors when choosing Hibernation mode:

❖ While in Hibernation mode, the computer uses no battery

power.

❖ Because the state of the system is held on the hard disk,

no data is lost if the battery discharges.

❖ Restarting from Hibernation mode uses less time and

battery power than restarting from Turn Off.

❖ Restarting from Hibernation mode uses a little more time

and battery power than restarting from Stand by because
information is being retrieved from the hard disk instead
of memory.

Learning the Basics

90

Using Turn Off or Shut down

❖ When starting up again, the computer returns to the state

in which you left it, including all open programs and files
you were using.

For more information about the Hibernation command, see

“Using Hibernation” on page 92. For information about

going into Hibernation mode more quickly, see “Going into

Hibernation mode more quickly” on page 93.

Stand By command

The Stand by puts the computer into a power-saving mode.
Stand by holds the current state of the computer in memory
so that, when you restart the computer, you can continue
working from where you left off.

Factors when choosing Stand by:

❖ While in Stand by mode, the computer uses some battery

power. The battery will eventually discharge in Stand by
mode. If the battery discharges, your data will be lost if
you do not save your work before entering Stand by
mode.

❖ Restarting from Stand by mode uses less time and battery

power than restarting from Turn Off or Hibernation
mode.

❖ When starting up again, the computer returns to the mode

in which you left it, including all open programs and files
you were using.

NOTE: If you power down using the Stand by and the battery
discharges fully, your information will be lost. Be sure to save your
work first.

For more information about the Stand by, see “Using Stand

by” on page 94. For information about going into Stand by

mode more quickly, see “Going into Stand by mode more

quickly” on page 95.

Turning off more quickly

You can also turn off the computer by pressing the power
button or closing the display panel.

To use either of these methods, you first need to turn on the
feature in the Toshiba Power Management Utility.

1 Click Start, Control Panel, then Performance and

Maintenance.

2 Double-click the Toshiba Power Management icon.

The Power Options Properties dialog box appears.

3 Click the Advanced tab, and select the options you want.

❖ When I close the lid of my portable computer

Set this option to Power Off to have the computer
shut down when you close the display panel.

❖ When I press the power button on my computer

Set this option to Power Off to have the computer
shut down when you press the power button.

Learning the Basics

Using Turn Off or Shut down

91

Sample Toshiba Power Management Advanced tab

4 Click Apply.

5 Click OK, then close the Control Panel.

Learning the Basics

92

Using Hibernation

Starting again after Turn Off

To start the computer up again, press and release the power
button. The on/off light turns on.

Using Hibernation

Follow these steps to power down the computer using
Hibernation:

1 Click Start, select Turn off computer.

The Turn off computer dialog box appears.

2 Hold down the shift key.

The Stand by option changes to the Hibernation option.

Sample Turn off computer dialog box

3 Click Hibernate.

The computer saves the mode of the system, including all
open programs and files, to the hard disk, and then powers
down completely.

Learning the Basics

Using Hibernation

93

Going into Hibernation mode more quickly

You can also put the computer into Hibernation mode by
pressing the power button or closing the display panel.

1 Click Start, Control Panel, then Performance and

Maintenance.

2 Double-click the Toshiba Power Management icon.

3 Click the Advanced tab, and select the options you want.

❖ When I press the power button

Set this option to Hibernation for the computer to go
into Hibernation mode when you press the power
button.

❖ When I close the lid

Set this option to Hibernation for the computer to go
into Hibernation mode when you close the display
panel.

Sample Toshiba Power Management Advanced tab

4 Click Apply.

5 Click OK, then close the Control Panel.

Learning the Basics

94

Using Stand by

Starting again from Hibernation mode

To start the computer from Hibernation mode, press and
release the power button. The computer returns to the screen
you were using.

If you put the computer in Hibernation mode by closing the
display panel, you can start it again by opening the display
panel.

NOTE: If your computer is running on batteries, you cannot start it
again by opening the display panel. To turn the system back on,
press the Power button.

Using Stand by

Follow these steps to power down the computer using the
Stand by:

1 Click Start, select Turn off computer.

The Turn off computer box appears.

2 Click Stand By.

Sample Turn off computer dialog box

The computer saves the status of all open programs and files
to memory, turns off the display, and goes into a low-power
mode. The on/off light blinks to indicate the machine is in
Stand by mode.

Learning the Basics

Using Stand by

NOTE: If you power down using the Stand by and the battery
discharges fully, your information will be lost. Be sure to save your
work first.

NOTE: If you power down using the Stand by and the battery
discharges fully, your information will be lost. Be sure to save your
work first.

Going into Stand by mode more quickly

In addition, you can put the computer into Stand by mode by
either pressing the power button or closing the display panel.
You can also specify an amount of time after which the
computer automatically goes into Stand by mode.

To use any of these methods, you first need to enable them in
Toshiba’s Power Saver utility.

95

1 Open the Start menu, then click Control Panel.

2 Click the Performance and Maintenance icon, and then

click the Toshiba Power Management icon.

3 Click the Advanced tab.

4 Select Stand By for the options you want.

When I press the power button

Set this option to Stand By to put the computer into
Stand by mode when you press the power button.

When I close the lid
Set this option to Stand By to put the computer into
Stand by mode when you close the display panel.

5 Click OK.

6 Close the Control Panel.

Learning the Basics

96

Toshiba’s online resources

Starting again from Stand by

To start the computer from Stand by mode, press the power
button. The computer returns to the screen you were using.

If you put the computer in Stand by mode by closing the
display panel, you can start it again by opening the display
panel.

Toshiba’s online resources

Toshiba maintains a number of online sites to which you can
connect. These sites provide information about Toshiba
products, give help with technical questions, and keep you up
to date with future upgrades. For more information, see

“Contacting Toshiba” on page 211.

Chapter 4

Mobile Computing

This chapter covers all aspects of using your computer while
traveling.

Toshiba’s energy-saver design

Your computer enters a low-power standby mode when it is
not being used, thereby conserving energy and saving money
in the process. It has a number of other features that enhance
its energy efficiency.

Many of these energy-saving features have been set by
Toshiba. We recommend you leave these features active,
allowing your computer to operate at its maximum energy
efficiency, so that you can use it for longer periods while
traveling.

97

Mobile Computing

98

Running the computer on battery power

Running the computer on battery power

The computer contains a removable Lithium Ion (Li-Ion)
high-capacity battery that provides power when you are away
from an AC outlet. You can recharge it many times.

Battery Notice

Battery life may vary depending on applications, power
management settings and features utilized. Recharge time varies
depending on usage. The battery may not charge while the
computer is consuming full power.

After a period of time, the battery will lose its ability to
perform at maximum capacity and will need to be replaced.
This is normal for all batteries. To purchase a new battery
pack, see your accessories information that shipped with your
computer, or visit the Toshiba Web site at: toshiba.com.

To ensure that the battery maintains its maximum capacity,
operate the computer on battery power at least once a month
until the battery is fully discharged. Please see “Maximizing

battery life” on page 107 for procedures. If the computer is

continuously operated on AC power, either through an AC
adapter or a docking station (if applicable to your system), for
an extended period (more than a month) the battery may fail
to retain a charge. This may shorten the life of the battery, and
the battery light may not indicate a low-battery condition.

In addition, the computer has an internal real-time clock
(RTC) battery. The RTC battery powers the RTC memory,
which stores your system configuration settings and the
current time and date for up to a month while the computer is
turned off.

NOTE: For optimum DVD performance, Toshiba recommends that
you play DVDs while running on AC power rather than on battery
power.

Power management

Your computer ships with the power management options
preset to a configuration that will provide the most stable
operating environment and optimum system performance for
both AC power and battery modes.

CAUTION: Changes to these settings may result in system
performance or stability issues. Users who are not completely
familiar with the power management component of the system
should use the preset configuration. For assistance with setup
changes, contact Toshiba’s InTouch Center.

Charging the battery

NOTE: Battery charge time may vary depending on the
applications, power management settings, and features used.

Mobile Computing

Charging the battery

99

The battery needs to be charged before you can use it to
power the computer.

To charge the battery, plug the computer into a live wall
outlet. It takes several hours to charge the battery with the
computer off. It takes much longer to charge the battery while
the computer is on.

TECHNICAL NOTE: The battery does not charge while the
computer is consuming full power.

The battery may not start charging immediately if:

❖ The battery is extremely hot or cold.

Mobile Computing

100

Charging the battery

To ensure that the battery charges to its full capacity, wait
until it reaches room temperature (50 to 80 degrees
Fahrenheit, 10 to 26 degrees Celsius).

❖ The battery is almost completely discharged.

Leave the power connected, and the battery should begin
charging after a few minutes.

HINT: Once the battery is fully charged, we recommend that you
operate your computer on battery power until the battery
discharges completely. Doing this extends battery life and helps
ensure accurate monitoring of battery capacity.

Charging the RTC battery

The computer contains an internal battery that provides
power for the real-time clock (RTC) and calendar.

During normal use, the main battery keeps the RTC battery
adequately charged. Occasionally, the RTC battery may lose
its charge completely, especially if you have had the
computer turned off for a long time.

If the RTC battery is low, the real-time clock and calendar
may display the incorrect time and date, or stop working.

To recharge the RTC battery, plug in the computer and leave
it turned off for at least 24 hours.

NOTE: When Hibernate mode is enabled and the RTC battery is
completely discharged, a warning prompts you to reset the real­time clock.