Toshiba S750 User Manual

User’s Manual

Satellite Pro S750
Series

Table of Contents

Copyright. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi

Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi

Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi

FCC information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

EU Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii

Video Standard Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

VCCI Class B Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

Canadian regulatory information (Canada only) . . . . . . . . . . . . . . . . . ix

Modem warning notice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x

Japan regulations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi

Instructions for IC CS-03 certified equipment . . . . . . . . . . . . . . . . . . xiii

Notes for Users in Australia and New Zealand . . . . . . . . . . . . . . . . . xiv

Following information is only valid for EU-member States:. . . . . . . xvii

Disposing of the computer and the computer's batteries . . . . . . . xviii

REACH - Compliance Statement. . . . . . . . . . . . . . . . . . . . . . . . . . . . xviii

Following information is only for Turkey: . . . . . . . . . . . . . . . . . . . . xviii

Optical disc drive safety instructions. . . . . . . . . . . . . . . . . . . . . . . . xviii

International precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xx

Preface

Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxi

General Precautions

Provide adequate ventilation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxiv

Creating a computer-friendly environment . . . . . . . . . . . . . . . . . . . . xxv

Stress injury . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxv

Heat injury . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxv

Pressure or impact damage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxvi

PC Card/ExpressCard overheating . . . . . . . . . . . . . . . . . . . . . . . . . . xxvi

Mobile phones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxvi

Instruction Manual for Safety and Comfort . . . . . . . . . . . . . . . . . . . xxvi

Chapter 1 Getting Started

Equipment checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

User’s Manual ii

Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

System Recovery Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12

System Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12

Chapter 2 The Grand Tour

Front with the display closed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Left side. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Right side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Back . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

Underside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

Front with the display open. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8

Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11

Optical disc drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15

AC adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16

Chapter 3 Hardware, Utilities and Options

Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Special features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

Utilities and Applications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9

Optional devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14

Memory media slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18

Optional accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-31

Chapter 4 Operating Basics

Using the Touch Pad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Using the Fingerprint Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

Web Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9

Using the TOSHIBA Face Recognition . . . . . . . . . . . . . . . . . . . . . . . 4-10

Using optical disc drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13

Writing CD/DVDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16

TOSHIBA VIDEO PLAYER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-22

Media care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-24

Sound System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25

Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-27

Wireless communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-30

LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-33

Computer Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-35

Using the TOSHIBA Sleep Utility. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-36

Heat dispersal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-38

Chapter 5 The Keyboard

Typewriter keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Function keys: F1 … F12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

Soft keys: FN key combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

Hot keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3

Windows special keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5

Keypad overlay for A4 size keyboard . . . . . . . . . . . . . . . . . . . . . . . . . 5-5

Satellite Pro S750

User’s Manual iii

Generating ASCII characters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7

Chapter 6 Power and Power-Up Modes

Power conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

Monitoring of power condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2

Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3

TOSHIBA Password Utility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9

Power-up modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12

Panel power on/off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12

System automatic Sleep/Hibernation . . . . . . . . . . . . . . . . . . . . . . . . 6-12

Chapter 7 HW Setup

Accessing HW Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

HW Setup window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

Chapter 8 Troubleshooting

Problem solving process. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

Hardware and system checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3

TOSHIBA support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-21

Appendix A Specifications

Physical Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Environmental Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Appendix B Display Controller and Video mode

Display controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1

Video mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1

Appendix C Information for Wireless Devices

Wireless LAN Interoperability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1

Bluetooth wireless technology Interoperability . . . . . . . . . . . . . . . . C-1

CAUTION about Wireless Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2

Wireless Devices and your health . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2

Radio Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-3

Radio approvals for wireless devices . . . . . . . . . . . . . . . . . . . . . . . . C-8

Appendix D AC Power Cord and Connectors

Certification agencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-1

Appendix E TOSHIBA PC Health Monitor

Starting the TOSHIBA PC Health Monitor. . . . . . . . . . . . . . . . . . . . . . E-2

If a TOSHIBA PC Health Monitor message is displayed . . . . . . . . . . E-2

Cleaning the cooling module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-2

Appendix F Legal Footnotes

Non-applicable Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-1

CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-1

Memory (Main System) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-2

Battery Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-3

Hard Disk Drive (HDD) Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-3

Satellite Pro S750

User’s Manual iv

Satellite Pro S750

LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-3

Graphics Processing Unit ("GPU") . . . . . . . . . . . . . . . . . . . . . . . . . . . F-3

Wireless LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-4

Copy Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-4

Glossary

Index

User’s Manual v

Copyright

Disclaimer

Satellite Pro S750

© 2011 by TOSHIBA Corporation. All rights reserved. Under the copyright
laws, this manual cannot be reproduced in any form without the prior
written permission of TOSHIBA. No patent liability is assumed, with respect
to the use of the information contained herein.

First edition April 2011
Copyright authority for music, movies, computer programs, databases and

other intellectual property covered by copyright laws belongs to the author
or to the copyright owner. Copyrighted material can be reproduced only for
personal use or use within the home. Any other use beyond that stipulated
above (including conversion to digital format, alteration, transfer of copied
material and distribution on a network) without the permission of the
copyright owner is a violation of copyright or author's rights and is subject to
civil damages or criminal action. Please comply with copyright laws in
making any reproduction from this manual.

This manual has been validated and reviewed for accuracy. The
instructions and descriptions it contains are accurate for your computer at
the time of this manual’s production. However, succeeding computers and
manuals are subject to change without notice. TOSHIBA assumes no
liability for damages incurred directly or indirectly from errors, omissions or
discrepancies between the computer and the manual.

Trademarks

Intel, Intel SpeedStep, Intel Core and Centrino are trademarks or registered
trademarks of Intel Corporation.

Windows, Microsoft and Windows logo are registered trademarks of
Microsoft Corporation.

Bluetooth is a trademark owned by its proprietor and used by TOSHIBA
under license.

Photo CD is a trademark of Eastman Kodak Company.
Memory Stick, Memory Stick PRO, Memory Stick Duo, Memory Stick PRO

Duo, Memory Stick Micro and i.LINK are trademarks or registered
trademarks of Sony Corporation.

ConfigFree is a trademark of Toshiba Corporation.
Wi-Fi is a registered trademark of the Wi-Fi Alliance.
Secure Digital and SD are trademarks of SD Card Association.
MultiMediaCard and MMC are trademarks of MultiMediaCard Association.
xD-Picture Card is a trademark of FUJIFILM Corporation.
Atheros is a registered trademark of Atheros Communication, Inc.
Other trademarks and registered trademarks not listed above may be used

in this manual.

User’s Manual vi

FCC information

FCC notice "Declaration of Conformity Information"

This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

■ Reorient or relocate the receiving antenna.

■ Increase the separation between the equipment and receiver.

■ Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

■ Consult the dealer or an experienced radio/TV technician for help.

Only peripherals complying with the FCC class B limits may be attached to
this equipment. Operation with non-compliant peripherals or peripherals
not recommended by TOSHIBA is likely to result in interference to radio
and TV reception. Shielded cables must be used between the external
devices and the computer’s external monitor port, Universal Serial Bus
(USB 2.0) ports, eSATA/USB combo port, Mini DisplayPort, serial port and
microphone jack. Changes or modifications made to this equipment, not
expressly approved by TOSHIBA or parties authorized by TOSHIBA could
void the user’s authority to operate the equipment.

Satellite Pro S750

FCC conditions

This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including
interference that may cause undesired operation.

Contact

Address: TOSHIBA America Information Systems, Inc.

9740 Irvine Boulevard
Irvine, California 92618-1697

Telephone: [phone]

User’s Manual vii

EU Declaration of Conformity

This product is carrying the CE-Mark in accordance with the related
European Directives. Responsible for CE-Marking is TOSHIBA Europe
GmbH, Hammfelddamm 8, 41460 Neuss, Germany. The complete and
official EU Declaration of Conformity can be found on TOSHIBA’s web site
http://epps.toshiba-teg.com on the Internet.

CE compliance

This product is labelled with the CE Mark in accordance with the related
European Directives, notably Electromagnetic Compatibility Directive
2004/108/EC for the notebook and the electronic accessories including the
supplied power adapter, the Radio Equipment and Telecommunications
Terminal Equipment Directive 1999/5/EC in case of implemented
telecommunication accessories and the Low Voltage Directive 2006/95/EC
for the supplied power adapter. Furthermore the product complies with the
Ecodesign Directive 2009/125/EC (ErP) and its related implementing
measures.

This product and the original options are designed to observe the related
EMC (Electromagnetic Compatibility) and safety standards. However,
TOSHIBA cannot guarantee that this product still observes these EMC
standards if options or cables not produced by TOSHIBA are connected or
implemented. In this case the persons who have connected/implemented
those options/cables have to provide assurance that the system (PC plus
options/cables) still fulfils the required standards. To avoid general EMC
problems, the following guidance should be noted:

■ Only CE marked options should be connected/implemented

■ Only best shielded cables should be connected

Satellite Pro S750

Working environment

This product was designed to fulfil the EMC (Electromagnetic Compatibility)
requirements to be observed for so-called "Residential, commercial and
light industry environments". TOSHIBA do not approve the use of this
product in working environments other than the above mentioned
"Residential, commercial and light industry environments".

For example, the following environments are not approved:

■ Industrial Environments (e.g. environments where a mains voltage of

380 V three-phase is used)

■ Medical Environments

■ Automotive Environments

■ Aircraft Environments

Any consequences resulting from the use of this product in working
environments that are not approved are not the responsibility of TOSHIBA.

User’s Manual viii

The consequences of the use of this product in non-approved working
environments may be:

■ Interference with other devices or machines in the near surrounding

area.

■ Malfunction of, or data loss from, this product caused by disturbances

generated by other devices or machines in the near surrounding area.

Therefore TOSHIBA strongly recommend that the electromagnetic
compatibility of this product should be suitably tested in all non-approved
working environments before use. In the case of automobiles or aircraft, the
manufacturer or airline respectively should be asked for permission before
use of this product.

Furthermore, for general safety reasons, the use of this product in
environments with explosive atmospheres is not permitted.

Video Standard Notice

THIS PRODUCT IS LICENSED UNDER THE AVC, THE VC-1 AND
MPEG-4 VISUAL PATENT PORTFOLIO LICENSE FOR THE PERSONAL
AND NON-COMMERCIAL USE OF A CONSUMER FOR (I) ENCODING
VIDEO IN COMPLIANCE WITH THE ABOVE STANDARDS ("VIDEO")
AND/OR (II) DECODING AVC, VC-1 AND MPEG-4 VIDEO THAT WAS
ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND
NONCOMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A
VIDEO PROVIDER LICENSED BY MPEG LA TO PROVIDE SUCH
VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY
OTHER USE. ADDITIONAL INFORMATION INCLUDING THAT
RELATING TO PROMOTIONAL, INTERNAL AND COMMERCIAL USES
AND LICENSING MAY BE OBTAINED FROM MPEG LA, L.L.C. SEE
HTTP://WWW.MPEGLA.COM.

Satellite Pro S750

VCCI Class B Information

Canadian regulatory information (Canada only)

This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus as set out in the Radio Interference
Regulation of the Canadian Department of Communications.

Note that Canadian Department of Communications (DOC) regulations
provide, that changes or modifications not expressly approved by
TOSHIBA Corporation could void your authority to operate this equipment.

User’s Manual ix

This Class B digital apparatus meets all requirements of the Canadian
Interference-Causng Equipment Regulations.

Cet appareil numérique de la class B respecte toutes les exgences du
Règlement sur le matériel brouileur du Canada.

Modem warning notice

This information is applicable to the models equipped with a built-in
modem.

Conformity Statement

The equipment has been approved to [Commission Decision "CTR21"] for
pan-European single terminal connection to the Public Switched Telephone
Network (PSTN).

However, due to differences between the individual PSTNs provided in
different countries/regions the approval does not, of itself, give an
unconditional assurance of successful operation on every PSTN network
termination point.

In the event of problems, you should contact your equipment supplier in the
first instance.

Network Compatibility Statement

This product is designed to work with, and is compatible with the following
networks. It has been tested to and found to conform with the additional
requirements conditional in EG 201 121.

Germany ATAAB AN005,AN006,AN007,AN009,AN010

Greece ATAAB AN005,AN006 and GR01,02,03,04
Portugal ATAAB AN001,005,006,007,011 and

Spain ATAAB AN005,007,012, and ES01
Switzerland ATAAB AN002
All other countries/regions ATAAB AN003,004

Specific switch settings or software setup are required for each network,
please refer to the relevant sections of the user guide for more details.

The hookflash (timed break register recall) function is subject to separate
national type approvals. It has not been tested for conformity to national
type regulations, and no guarantee of successful operation of that specific
function on specific national networks can be given.

Satellite Pro S750

and DE03,04,05,08,09,12,14,17

P03,04,08,10

User’s Manual x

Japan regulations

Region selection

If you are using the computer in Japan, technical regulations described in
the Telecommunications Business Law require that you select the Japan
region mode. It is illegal to use the modem in Japan with any other
selection.

Redial

Up to two redial attempts can be made. If more than two redial attempts are
made, the modem will return Black Listed. If you are experiencing
problems with the Black Listed code, set the interval between redials at one
minute or longer.

Japan’s Telecommunications Business Law permits up to two redials on
analogue telephones, but the redials must be made within a total of three
minutes.

The internal modem is approved by Japan Approvals Institute for
Telecommunications Equipment.

This label is located on the module.

Agere Systems
Delphi Modem D40
Revision AM5
Approval No. 3785

AGREE PAR L’ARNT MARCO

Numéro d’agrément: MF 2514 ANRT 2005

Date d’agrément: 31 AOUT2005

MDC Modem Module

Rating:3.3V

A05-0413001

TRA

REGISTERED No:

ER0045497/10

DEALER No:

DA0045491/10

Satellite Pro S750

Agere Delphi Modem D40 (AM5)

Agere Systems Inc.

Approved by PTA (2007)

Pakistan Telecom Authority

TE-2009/176

54-5681

CCAG10M10010T2

04604/I/R/POSTEL/2010

2457

㡕ᆜ冕ࠫᇞ冕ᕴ

D40 AM5

խ㧺ࠫທ

User’s Manual xi

Pursuant to FCC CFR 47, Part 68:

When you are ready to install or use the modem, call your local telephone
company and give them the following information:

■ The telephone number of the line to which you will connect the modem

■ The registration number that is located on the device

The FCC registration number of the modem will be found on either the
device which is to be installed, or, if already installed, on the bottom of
the computer outside of the main system label.

■ The Ringer Equivalence Number (REN) of the modem, which can vary.

For the REN of your modem, refer to your modem’s label.

The modem connects to the telephone line by means of a standard jack
called the USOC RJ11C.

Type of service

Your modem is designed to be used on standard-device telephone lines.
Connection to telephone company-provided coin service (central office
implemented systems) is prohibited. Connection to party lines service is
subject to state tariffs. If you have any questions about your telephone line,
such as how many pieces of equipment you can connect to it, the
telephone company will provide this information upon request.

Telephone company procedures

The goal of the telephone company is to provide you with the best service it
can. In order to do this, it may occasionally be necessary for them to make
changes in their equipment, operations, or procedures. If these changes
might affect your service or the operation of your equipment, the telephone
company will give you notice in writing to allow you to make any changes
necessary to maintain uninterrupted service.

Satellite Pro S750

If problems arise

If any of your telephone equipment is not operating properly, you should
immediately remove it from your telephone line, as it may cause harm to
the telephone network. If the telephone company notes a problem, they
may temporarily discontinue service. When practical, they will notify you in
advance of this disconnection. If advance notice is not feasible, you will be
notified as soon as possible. When you are notified, you will be given the
opportunity to correct the problem and informed of your right to file a
complaint with the FCC. In the event repairs are ever needed on your
modem, they should be performed by TOSHIBA Corporation or an
authorized representative of TOSHIBA Corporation.

Disconnection

If you should ever decide to permanently disconnect your modem from its
present line, please call the telephone company and let them know of this
change.

User’s Manual xii

Fax branding

The Telephone Consumer Protection Act of 1991 makes it unlawful for any
person to use a computer or other electronic device to send any message
via a telephone fax machine unless such message clearly contains in a
margin at the top or bottom of each transmitted page or on the first page of
the transmission, the date and time it is sent and an identification of the
business, other entity or individual sending the message and the telephone
number of the sending machine or such business, other entity or individual.
In order to program this information into your fax modem, you should
complete the setup of your fax software before sending messages.

Use only No. 26AWG or larger modular cable.

Instructions for IC CS-03 certified equipment

1. The Industry Canada label identifies certified equipment. This
certification means that the equipment meets certain
telecommunications network protective, operational and safety
requirements as prescribed in the appropriate Terminal Equipment
Technical Requirements document(s). The Department does not
guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is
permissible to be connected to the facilities of the local
telecommunications company. The equipment must also be installed
using an acceptable method of connection.

The customer should be aware that compliance with the above
conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be coordinated by a
representative designated by the supplier. Any repairs or alterations
made by the user to this equipment, or equipment malfunctions, may
give the telecommunications company cause to request the user to
disconnect the equipment.

Users should ensure for their own protection that the electrical ground
connections of the power utility, telephone lines and internal metallic
water pipe systems, if present, are connected together. This precaution
may be particularly important in rural areas.

Satellite Pro S750

Users should not attempt to make such connections themselves, but
should contact the appropriate electric inspection authority, or electrician,
as appropriate.

2. The user manual of analog equipment must contain the equipment’s
Ringer Equivalence Number (REN) and an explanation notice similar to
the following:

The Ringer Equivalence Number (REN) of the modem, which can vary.
For the REN of your modem, refer to your modem’s label.

User’s Manual xiii

The Ringer Equivalence Number (REN) assigned to each terminal device
provides an indication of the maximum number of terminals allowed to be
connected to a telephone interface. The termination on an interface may
consist of any combination of devices subject only to the requirement that
the sum of the Ringer Equivalence Numbers of all the devices does not
exceed 5.

3. The standard connecting arrangement (telephone jack type) for this
equipment is jack type(s): USOC RJ11C.
The IC registration number of the modem is shown below.

Canada: 4005B-DELPHI

Notes for Users in Australia and New Zealand

Modem warning notice for Australia

Modems connected to the Australian telecoms network must have a valid
Austel permit. This modem has been designed to specifically configure to
ensure compliance with Austel standards when the country/region selection
is set to Australia. The use of other country/region setting while the modem
is attached to the Australian PSTN would result in you modem being
operated in a non-compliant manner. To verify that the country/region is
correctly set, enter the command ATI which displays the currently active
setting.

To set the country/region permanently to Australia, enter the following
command sequence:

AT%T E=1
ATS133=1
AT&F
AT&W
AT%T E=0
ATZ

Failure to set the modem to the Australia country/region setting as shown
above will result in the modem being operated in a non-compliant manner.
Consequently, there would be no permit in force for this equipment and the
Telecoms Act 1991 prescribes a penalty of $12,000 for the connection of
non-permitted equipment.

Satellite Pro S750

User’s Manual xiv

Notes for use of this device in New Zealand

■ The grant of a Telepermit for a device in no way indicates Telecom

acceptance of responsibility for the correct operation of that device
under all operating conditions. In particular the higher speeds at which
this modem is capable of operating depend on a specific network
implementation which is only one of many ways of delivering high
quality voice telephony to customers. Failure to operate should not be
reported as a fault to Telecom.

■ In addition to satisfactory line conditions a modem can only work

properly if:
a/ it is compatible with the modem at the other end of the call and.
b/ the application using the modem is compatible with the application

at the other end of the call - e.g., accessing the Internet requires
suitable software in addition to a modem.

■ This equipment shall not be used in any manner which could constitute

a nuisance to other Telecom customers.

■ Some parameters required for compliance with Telecom’s PTC

Specifications are dependent on the equipment (PC) associated with
this modem. The associated equipment shall be set to operate within
the following limits for compliance with Telecom Specifications:

a/ There shall be no more than 10 call attempts to the same number

within any 30 minute period for any single manual call initiation, and

b/ The equipment shall go on-hook for a period of not less than 30

seconds between the end of one attempt and the beginning of the
next.

c/ Automatic calls to different numbers shall be not less than 5

seconds apart.

■ Immediately disconnect this equipment should it become physically

damaged, and arrange for its disposal or repair.

■ The correct settings for use with this modem in New Zealand are as

follows:

ATB0 (CCITT operation)
AT&G2 (1800 Hz guard tone)
AT&P1 (Decadic dialing make-break ratio =33%/67%)
ATS0=0 (not auto answer)
ATS6=4 (Blind dial delay)
ATS7=less than 90 (Time to wait to carrier after dialing)
ATS10=less than 150 (loss of carrier to hangup delay, factory

default of 15 recommended)
ATS11=90 (DTMF dialing on/off duration=90 ms)
ATX2 (Dial tone detect, but not (U.S.A.) call progress detect)

Satellite Pro S750

User’s Manual xv

Satellite Pro S750

■ When used in the Auto Answer mode, the S0 register must be set with a

value of 3 or 4. This ensures:
a/ A person calling your modem will hear a short burst of ringing before

the modem answers. This confirms that the call has been
successfully switched through the network.

b/ Caller identification information (which occurs between the first and

second ring cadences) is not destroyed.

■ The preferred method of dialing is to use DTMF tones (ATDT...) as this

is faster and more reliable than pulse (decadic) dialing. If for some
reason you must use decadic dialing, your communications program
must be set up to record numbers using the following translation table
as this modem does not implement the New Zealand “Reverse Dialing”
standard.

Number to be dialed: 0 1 2 3 4 5 6 7 8 9
Number to program into computer: 0 9 8 7 6 5 4 3 2 1
Note that where DTMF dialing is used, the numbers should be

entered normally.

■ The transmit level from this device is set at a fixed level and because of

this there may be circumstances where the performance is less than
optimal. Before reporting such occurrences as faults, please check the
line with a standard Telepermitted telephone, and only report a fault if
the phone performance is impaired.

■ It is recommended that this equipment be disconnected from the

Telecom line during electrical storms.

■ When relocating the equipment, always disconnect the Telecom line

connection before the power connection, and reconnect the power first.

■ This equipment may not be compatible with Telecom Distinctive Alert

cadences and services such as FaxAbility.

NOTE THAT FAULT CALLOUTS CAUSED BY ANY OF THE ABOVE
CAUSES MAY INCUR A CHARGE FROM TELECOM

General conditions

As required by PTC 100, please ensure that this office is advised of any
changes to the specifications of these products which might affect
compliance with the relevant PTC Specifications.

The grant of this Telepermit is specific to the above products with the
marketing description as stated on the Telepermit label artwork. The
Telepermit may not be assigned to other parties or other products without
Telecom approval.

A Telepermit artwork for each device is included from which you may
prepare any number of Telepermit labels subject to the general instructions
on format, size and color on the attached sheet.

The Telepermit label must be displayed on the product at all times as proof
to purchasers and service personnel that the product is able to be
legitimately connected to the Telecom network.

The Telepermit label may also be shown on the packaging of the product
and in the sales literature, as required in PTC 100.

User’s Manual xvi

Satellite Pro S750

The charge for a Telepermit assessment is $337.50. An additional charge
of $337.50 is payable where an assessment is based on reports against
non-Telecom New Zealand Specifications. $112.50 is charged for each
variation when submitted at the same time as the original.

An invoice for $NZ1237.50 will be sent under separate cover.

Following information is only valid for EU-member States:

Disposal of products

The crossed out wheeled dust bin symbol indicates that products must be
collected and disposed of separately from household waste. Integrated
batteries and accumulators can be disposed of with the product. They will
be separated at the recycling centres.

The black bar indicates that the product was placed on the market after
August 13, 2005.
By participating in separate collection of products and batteries, you will
help to assure the proper disposal of products and batteries and thus help
to prevent potential negative consequences for the environment and
human health.

For more detailed information about the collection and recycling
programmes available in your country, please visit our website
(http://eu.computers.toshiba-europe.com) or contact your local city office or
the shop where you purchased the product.

Disposal of batteries and/or accumulators

The crossed out wheeled dust bin symbol indicates that batteries and/or
accumulators must be collected and disposed of separately from
household waste.

If the battery or accumulator contains more than the specified values of
lead (Pb), mercury (Hg), and/or cadmium (Cd) defined in the Battery
Directive (2006/66/EC), then the chemical symbols for lead (Pb), mercury
(Hg) and/or cadmium (Cd) will appear below the crossed out wheeled dust
bin symbol.

By participating in separate collection of batteries, you will help to assure
the proper disposal of products and batteries and thus help to prevent
potential negative consequences for the environment and human health.
For more detailed information about the collection and recycling
programmes available in your country, please visit our website
(http://eu.computers.toshiba-europe.com) or contact your local city office or
the shop where you purchased the product.

These symbols may not stick depending on the country and region where
you purchased.

User’s Manual xvii

Satellite Pro S750

Disposing of the computer and the computer's batteries

■ Discard this computer in accordance with applicable laws and

regulations. For further information, contact your local government.

■ This computer contains rechargeable batteries. After repeated use, the

batteries will finally lose their ability to hold a charge and you will need
to replace them. Under certain applicable laws and regulation, it may be
illegal to dispose of old batteries by placing them in the trash.

■ Please be kind to our shared environment. Check with your local

government authority for details regarding where to recycle old batteries
or how to dispose of them properly.

REACH - Compliance Statement

The new European Union (EU) chemical regulation, REACH (Registration,
Evaluation, Authorization and Restriction of Chemicals), entered into force
on 1 June 2007. TOSHIBA will meet all REACH requirements and is
committed to provide our customers with information about the chemical
substances in our products according to REACH regulation.

Please consult the following website
www.toshiba-europe.com/computers/info/reach for information about the
presence in our articles of substances included on the candidate list
according to article 59(1) of Regulation (EC) No 1907/2006 („REACH“) in a
concentration above 0.1% weight by weight.

Following information is only for Turkey:

■ Compliant with EEE Regulations: TOSHIBA meets all requirements

of Turkish regulation 26891 "Restriction of the use of certain hazardous
substances in electrical and electronic equipment".

■ The number of possible pixel failures of your display is defined

according to ISO 13406-2 standards. If the number of pixel failures is
less than this standard, they will not be counted as defect or failure.

■ Battery is a consumption product, since the battery time depends on the

usage of your computer. If the battery can not be charged at all, then it
is a defect or failure. The changes in battery time is not a defect or
failure.

Optical disc drive safety instructions

Be sure to check the international precautions at the end of this section.

User’s Manual xviii

■ The DVD-ROM/DVD Super Multi drive model employs a laser system.

To ensure proper use of this product, please read this instruction
manual carefully and retain for future reference. Should the unit ever
require maintenance, contact an authorized service location.

■ Use of controls, adjustments or the performance of procedures other

than those specified may result in hazardous radiation exposure.

■ To prevent direct exposure to the laser beam, do not try to open the

enclosure.

TEAC

■ DVD-ROM drive DV-28S

■ DVD Super Multi with Double Layer Recording DV-W28S

Satellite Pro S750

Panasonic Communications

■ DVD Super Multi with Double Layer Recording UJ8A0

Panasonic System Networks Co., Ltd.

User’s Manual xix

Toshiba Samsung Storage Technology

■ DVD Super Multi with Double Layer Recording TS-L633

International precautions

Satellite Pro S750

CAUTION: This appliance contains a
laser system and is classified as a
“CLASS 1 LASER PRODUCT.” To use
this model properly, read the instruction
manual carefully and keep this manual
for your future reference. In case of any
trouble with this model, please contact
your nearest “AUTHORIZED service
station.” To prevent direct exposure to the
laser beam, do not try to open the
enclosure.

User’s Manual xx

Preface

Congratulations on your purchase of this computer. This powerful notebook
computer provides excellent expansion capability, includes multimedia
functionality, and is designed to provide years of reliable, high-performance
computing.

This manual tells how to set up and begin using your computer. It also
provides detailed information on configuring your computer, basic
operations and care, using optional devices and troubleshooting.

If you are a new user of computers or if you’re new to portable computing,
first read over the Chapter 1, Getting Started and Chapter 3, Hardware,

Utilities and Options chapters to familiarize yourself with the computer’s

features, components and accessory devices. Then read Chapter 1,

Getting Started for step-by-step instructions on setting up your computer.

If you are an experienced computer user, please continue reading the
preface to learn how this manual is organized, then become acquainted
with this manual by browsing through its pages. Be sure to read the Special

features section in Chapter 3, Hardware, Utilities and Options to learn

about features that are uncommon or unique to this computer, as well as
the section on Chapter 7, HW Setup, to understand how to setup and
configure these features.

Read Chapter 3, Hardware, Utilities and Options if connecting optional
products or external devices.

Conventions

This manual uses the following formats to describe, identify, and highlight
terms and operating procedures.

Abbreviations

On first appearance, and whenever necessary for clarity, abbreviations are
enclosed in parentheses following their definition. For example: Read Only
Memory (ROM). Acronyms are also defined in the Glossary.

User’s Manual xxi

Icons

Icons identify ports, dials, and other parts of your computer. The indicator
panel also uses icons to identify the components it is providing information
on.

Keys

The keyboard keys are used in the text to describe many computer
operations. A distinctive typeface identifies the key top symbols as they
appear on the keyboard. For example, ENTER identifies the ENTER key.

Key operation

Some operations require you to simultaneously use two or more keys. We
identify such operations by the key top symbols separated by a plus sign
(+). For example, CTRL + C means you must hold down CTRL and at the
same time press C. If three keys are used, hold down the first two and at
the same time press the third.

Satellite Pro S750

ABC

When procedures require an action such as
clicking an icon or entering text, the icon's name
or the text you are to type in is represented in the
typeface you see to the left.

Display

S ABC

Names of windows or icons or text generated by
the computer that appear on its display screen
are presented in the type face you see to the left.

Messages

Messages are used in this manual to bring important information to your
attention. Each type of message is identified as shown below.

Pay attention! A caution informs you that improper use of equipment or
failure to follow instructions may cause data loss or damage your
equipment.

Please read. A note is a hint or advice that helps you make best use of
your equipment.

Indicates a potentially hazardous situation, which could result in death or
serious injury, if you do not follow instructions.

User’s Manual xxii

Terminology

This term is defined in this document as follows:

Start The word "Start" refers to the " " button in

Windows 7.

HDD or Hard disk
drive

Some models are equipped with a "Solid State
Drive (SSD)" instead of a hard disk drive.

In this manual, the word "HDD" or "Hard disk
drive" also refers to the SSD unless otherwise
stated.

Satellite Pro S750

User’s Manual xxiii

General Precautions

TOSHIBA computers are designed to optimize safety, minimize strain and
withstand the rigors of portability. However, certain precautions should be
observed to further reduce the risk of personal injury or damage to the
computer.

Be certain to read the general precautions below and to note the cautions
included in the text of the manual.

Provide adequate ventilation

■ Always make sure your computer and AC adaptor have adequate

ventilation and are protected from overheating when the power is
turned on or when an AC adaptor is connected to a power outlet (even if
your computer is in Sleep Mode). In this condition, observe the
following:

■ Never cover your computer or AC adaptor with any object.

■ Never place your computer or AC adaptor near a heat source, such

as anelectric blanket or heater.

■ Never cover or block the air vents including those located at the

base of the computer.

■ Always operate your computer on a hard flat surface. Using your

computer on a carpet or other soft material can block the vents.

■ Always provide sufficient space around the computer.

■ Overheating your computer or AC adaptor could cause system failure,

computer or AC adaptor damage or a fire, possibly resulting in serious
injury.

User’s Manual xxiv

Creating a computer-friendly environment

Place the computer on a flat surface that is large enough for the computer
and any other items you are using, such as a printer.

Leave enough space around the computer and other equipment to provide
adequate ventilation. Otherwise, they may overheat.

To keep your computer in prime operating condition, protect your work area
from:

■ Dust, moisture, and direct sunlight.

■ Equipment that generates a strong electromagnetic field, such as

stereo speakers (other than speakers that are connected to the
computer) or speakerphones.

■ Rapid changes in temperature or humidity and sources of temperature

change such as air conditioner vents or heaters.

■ Extreme heat, cold, or humidity.

■ Liquids and corrosive chemicals.

Stress injury

Carefully read the Instruction Manual for Safety and Comfort. It contains
information on the prevention of stress injuries to your hands and wrists
that can be caused by extensive keyboard use. Instruction Manual for
Safety and Comfort also includes information on work space design,
posture and lighting that can help reduce physical stress.

Satellite Pro S750

Heat injury

■ Avoid prolonged physical contact with the computer. If the computer is

used for long periods, its surface can become very warm. While the
temperature will not feel hot to the touch, if you maintain physical
contact with the computer for a long time, for example if you rest the
computer on your lap or if you keep your hands on the palm rest, your
skin might suffer a low-heat injury.

■ If the computer has been used for a long time, avoid direct contact with

the metal plate supporting the various interface ports as this can
become hot.

■ The surface of the AC adaptor can become hot when in use but this

condition does not indicate a malfunction. If you need to transport the
AC adaptor, you should disconnect it and let it cool before moving it.

■ Do not lay the AC adaptor on a material that is sensitive to heat as the

material could become damaged.

User’s Manual xxv

Pressure or impact damage

Do not apply heavy pressure to the computer or subject it to any form of
strong impact as this can damage the computer's components or otherwise
cause it to malfunction.

PC Card/ExpressCard overheating

Some PC Cards/ExpressCards can become hot during prolonged use
which may result in errors or instability in the operation of the device in
question. In addition, you should also be careful when you remove a PC
Card/ExpressCard that has been used for a long time.

Mobile phones

Please be aware that the use of mobile phones can interfere with the audio
system. The operation of the computer will not be impaired in any way, but
it is recommended that a minimum distance of 30cm is maintained between
the computer and a mobile phone that is in use.

Instruction Manual for Safety and Comfort

All important information on the safe and proper use of this computer is
described in the enclosed Instruction Manual for Safety and Comfort. Be
sure to read it before using the computer.

Satellite Pro S750

User’s Manual xxvi

Getting Started

This chapter provides an equipment checklist, and basic information to start
using your computer.

Some of the features described in this manual may not function properly if
you use an operating system that was not pre-installed by TOSHIBA.

Equipment checklist

Carefully unpack your computer, taking care to save the box and packaging
materials for future use.

Hardware

Check to make sure you have all the following items:

■ TOSHIBA Portable Personal Computer

■ AC adaptor and power cord (2-pin plug or 3-pin plug)

■ Battery pack

Chapter 1

Documentation

■ User Information Guide

■ Instruction Manual for Safety and Comfort

If any of the items are missing or damaged, contact your dealer
immediately.

User’s Manual 1-1

Software

The following Windows® operating system and utility software are pre­installed.

■ Windows 7

■ TOSHIBA Value Added Package

■ TOSHIBA Recovery Media Creator

■ TOSHIBA VIDEO Player

■ TOSHIBA Assist

■ TOSHIBA ConfigFree™

■ TOSHIBA Disc Creator

■ TOSHIBA Face Recognition

■ TOSHIBA eco Utility

■ TOSHIBA Sleep Utility

■ TOSHIBA Bulletin Board

■ TOSHIBA ReelTime

■ TOSHIBA Speech System

■ TOSHIBA Media Controller

■ Fingerprint Utility

■ Online Manual

■ Satellite Pro S750 User's Manual (This manual)

* You may not have all the softwares listed above depending on the

model you purchased.

Getting Started

Getting Started

■ All users should be sure to read the section Starting up for the first time.

■ Be sure to read the enclosed Instruction Manual for Safety and Comfort

for information on the safe and proper use of this computer. It is
intended to help you be more comfortable and productive while using a
notebook computer. By following the recommendations in it you may
reduce your chance of developing a painful or disabling injury to your
hand, arms, shoulders or neck.

This section provides basic information to start using your computer. It
covers the following topics:

■ Connecting the AC adaptor

■ Opening the display

■ Turning on the power

■ Starting up for the first time

■ Turning off the power

■ Restarting the computer

User’s Manual 1-2

■ System Recovery Options

■ Creating Recovery Media

■ Restoring the pre-installed software from the Recovery hard disk drive

■ Restoring the pre-installed software from your created Recovery Media

■ Use a virus-check program and make sure it is updated regularly.

■ Never format storage media without checking its content - formatting

destroys all stored data.

■ It is a good idea to periodically back up the internal hard disk drive or

other main storage device to external media. General storage media is
not durable or stable over long periods of time and under certain
conditions may result in data loss.

■ Before you install a device or application, save any data in memory to

the hard disk drive or other storage media. Failure to do so may result
in the loss of data.

Connecting the AC adaptor

Attach the AC adaptor when you need to charge the battery or you want to
operate from AC power. It is also the fastest way to get started, because
the battery pack will need to be charged before you can operate from
battery power.

The AC adaptor can be connected to any power source supplying from 100
to 240 volts and 50 or 60 hertz. For details on using the AC adaptor to
charge the battery pack, refer to Chapter 6, Power and Power-Up Modes.

Getting Started

User’s Manual 1-3

Getting Started

■ Always use the TOSHIBA AC adaptor that was included with your

computer, or use AC adaptors specified by TOSHIBA to avoid any risk
of fire or other damage to the computer. Use of an incompatible AC
adaptor could cause fire or damage to the computer possibly resulting
in serious injury. TOSHIBA assumes no liability for any damage caused
by use of an incompatible adaptor.

■ Never plug the AC adaptor into a power source that does not

correspond to both the voltage and the frequency specified on the
regulatory label of the unit. Failure to do so could result in a fire or
electric shock, possibly resulting in serious injury.

■ Always use or purchase power cables that comply with the legal

voltage and frequency specifications and requirements in the country of
use. Failure to do so could result in a fire or electric shock, possibly
resulting in serious injury.

■ The supplied power cord conforms to safety rules and regulations in

the region the product is bought and should not be used outside this
region. For use in other regions, please buy power cords that conform
to safety rules and regulations in the particular region.

■ Do not use a 3-pin to 2-pin conversion plug.

■ When you connect the AC adaptor to the computer, always follow the

steps in the exact order as described in the User’s Manual. Connecting
the power cable to a live electrical outlet should be the last step
otherwise the adaptor DC output plug could hold an electrical charge
and cause an electrical shock or minor bodily injury when touched. As
a general safety precaution, avoid touching any metal parts.

■ Never place your computer or AC adaptor on a wooden surface,

furniture, or any other surface that could be marred by exposure to heat
since the computer base and AC adaptor's surface increase in
temperature during normal use.

■ Always place your computer or AC adaptor on a flat and hard surface

that is resistant to heat damage.

Refer to the enclosed Instruction Manual for Safety and Comfort for
detailed precautions and handling instructions.

User’s Manual 1-4

Getting Started

1. Connect the power cord to the AC adaptor.

Figure 1-1 Connecting the power cord to the AC adaptor (2-pin plug)

Figure 1-2 Connecting the power cord to the AC adaptor (3-pin plug)

Either a 2-pin or 3-pin adaptor/cord will be included with the computer
depending on the model.

2. Connect the AC adaptor’s DC output plug to the DC IN 15V jack on the
back of the computer.

1

2

1. DC IN 15V jack

Figure 1-3 Connecting the DC output plug to the computer

2. DC output plug

3. Plug the power cord into a live wall outlet - the Battery and DC IN
indicators on the front of the computer should glow.

User’s Manual 1-5

Opening the display

The display panel can be opened to a wide range of angles for optimal
viewing.

While holding down the palm rest with one hand so that the main body of
the computer is not raised, slowly lift the display panel - this will allow the
angle of the display panel to be adjusted to provide optimum clarity.

1. Display panel

Figure 1-4 Opening the display panel

Use reasonable care when opening and closing the display panel. Opening
it vigorously or slamming it shut could damage the computer.

Getting Started

1

■ Be careful not to open the display panel too far as this could put stress

on the display panel’s hinges and cause damage.

■ Do not press or push on the display panel.

■ Do not lift the computer by the display panel.

■ Do not close the display panel with pens or any other objects left in

between the display panel and the keyboard.

■ When opening or closing the display panel, place one hand on the

palm rest to hold the computer in place and use the other hand to
slowly open or close the display panel (Do not use excessive force
when opening or closing the display panel).

User’s Manual 1-6

Turning on the power

This section describes how to turn on the power - the Power indicator will
then indicate the status. Please refer to the Monitoring of power condition
section in Chapter 6, Power and Power-Up Modes for more information.

■ After you turn on the power for the first time, do not turn it off until you

have set up the operating system. Please refer to the section Starting

up for the first time for more information.

■ Volume cannot be adjusted during Windows Setup.

1. Open the display panel.

2. Press and hold the computer's power button for two or three seconds.

1

Getting Started

1. Power button

Figure 1-5 Turning on the power

Starting up for the first time

The Windows 7 Startup Screen will be the first screen displayed when you
turn on the power. Follow the on-screen instructions on each screen in
order to properly install the operating system.

When it is displayed, be sure to read the Software License Terms
carefully.

User’s Manual 1-7

Turning off the power

The power can be turned off in one of three modes, either Shut Down
Mode, Hibernation Mode or Sleep Mode.

Shut Down Mode

When you turn off the power in Shut Down Mode no data will be saved and
the computer will boot to the operating system's main screen the next time
it is turned on.

1. If you have entered data, either save it to the hard disk drive or to other
storage media.

2. Make sure all disk/disc activity has stopped before removing the
CD/DVD.

■ Make sure the Hard Disk Drive/Optical Disc Drive indicators are off.

If you turn off the power while a disk (disc) is being accessed, you may
lose data or damage the disk.

■ Never turn off the power while an application is running. Doing so could

cause loss of data.

■ Never turn off the power, disconnect an external storage device or

remove storage media during data read/write. Doing so can cause data
loss.

3. Click Start.

4. Click the Shut down button ( ).

5. Turn off any peripheral devices connected to your computer.

Getting Started

Do not turn the computer or peripheral devices back on immediately - wait
a short period to avoid any potential damage.

Sleep Mode

If you have to interrupt your work, you are able to turn off the power without
exiting from your software by placing the computer into Sleep Mode. In this
mode data is maintained in the computer's main memory so that when you
turn on the power again, you can continue working right where you left off.

When you have to turn off your computer aboard an aircraft or in places
where electronic devices are regulated or controlled, always completely
shut down the computer. This includes turning off any wireless
communication switches or devices, and canceling settings that reactivate
the computer automatically, such as a timer recording function. Failure to
completely shut down the computer in this way could allow the operating
system to reactivate and run pre-programmed tasks or preserve unsaved
data, which could interfere with aviation or other systems, possibly causing
serious injury.

User’s Manual 1-8

Getting Started

■ Before entering Sleep Mode, be sure to save your data.

■ Do not install or remove a memory module while the computer is in

Sleep Mode. The computer or the memory module could be damaged.

■ Do not remove the battery pack while the computer is in Sleep Mode

(unless the computer is connected to an AC power source). Data in
memory could be lost.

■ When the AC adaptor is connected, the computer will go into Sleep

Mode according to the settings in the Power Options (to access it, Start

-> Control Panel -> System and Security -> Power Options).

■ To restore the operation of the computer from Sleep Mode, press and

hold the power button or any key on the keyboard for a short amount of
time. Please note that keyboard keys can only be used if the Wake-up
on Keyboard option is enabled within the HW Setup utility.

■ If the computer enters Sleep Mode while a network application is

active, the application might not be restored when the computer is next
turned on and the system returns from Sleep Mode.

■ To prevent the computer from automatically entering Sleep Mode,

disable Sleep Mode within the Power Options (to access it, Start ->
Control Panel -> System and Security -> Power Options).

■ To use the Hybrid Sleep function, configure it in the Power Options.

Benefits of Sleep Mode

The Sleep Mode feature provides the following benefits:

■ Restores the previous working environment more rapidly than does the

Hibernation Mode feature.

■ Saves power by shutting down the system when the computer receives

no input or hardware access for the time period set by the System
Sleep Mode feature.

■ Allows the use of the panel power off feature.

Executing Sleep Mode

You can also enable Sleep Mode by pressing FN + F3 - please refer to
Chapter 5, The Keyboard, for further details.

You can enter Sleep Mode in one of three ways:

■ Click Start, point to the arrow icon ( ) and then select Sleep from

the menu.

■ Close the display panel. Please note that this feature must be enabled

within the Power Options (to access it, click Start -> Control Panel ->
System and Security -> Power Options).

■ Press the power button. Please note that this feature must be enabled

within the Power Options (to access it, click Start -> Control Panel ->
System and Security -> Power Options).

User’s Manual 1-9

Getting Started

When you turn the power back on, you can continue where you left when
you shut down the computer.

■ When the computer is in Sleep Mode, the power indicator will blink

orange.

■ If you are operating the computer on battery power, you can lengthen

the overall operating time by turning it off into Hibernation Mode - Sleep
Mode will consume more power while the computer is off.

Sleep Mode limitations

Sleep Mode will not function under the following conditions:

■ Power is turned back on immediately after shutting down.

■ Memory circuits are exposed to static electricity or electrical noise.

Hibernation Mode

The Hibernation Mode feature saves the contents of memory to the hard
disk drive when the computer is turned off so that, the next time it is turned
on, the previous state is restored. Please note that the Hibernation Mode
feature does not save the status of any peripheral devices connected to the
computer.

■ Save your data. While entering Hibernation Mode, the computer saves

the contents of memory to the hard disk drive. However, for safety
sake, it is best to save your data manually.

■ Data will be lost if you remove the battery or disconnect the AC adaptor

before the save is completed. Wait for the Hard Disk Drive/Optical
Disc Drive indicator to go out.

■ Do not install or remove a memory module while the computer is in

Hibernation Mode. Data will be lost.

Benefits of Hibernation Mode

The Hibernation Mode feature provides the following benefits:

■ Saves data to the hard disk drive when the computer automatically

shuts down because of a low battery condition.

■ You can return to your previous working environment immediately when

you turn on the computer.

■ Saves power by shutting down the system when the computer receives

no input or hardware access for the time period set by the System
Hibernate feature.

■ Allows the use of the panel power off feature.

User’s Manual 1-10

Getting Started

Starting Hibernation Mode

You can also enable Hibernation Mode by pressing FN + F4 - please refer
to Chapter 5, The Keyboard, for further details.

To enter Hibernation Mode, follow the steps below.

1. Click Start.

2. Point to the arrow icon ( ) and then select Hibernate from the
menu.

Automatic Hibernation Mode

The computer can be configured to enter Hibernation Mode automatically
when you press the power button or close the lid. In order to define these
settings, you can follow the steps as described below:

1. Click Start and click the Control Panel.

2. Click System and Security and click Power Options.

3. Click Choose what the power button does or Choose what closing
the lid does.

4. Enable the desired Hibernation Mode settings for When I press the
power button and When I close the lid.

5. Click the Save changes button.

Data save in Hibernation Mode

When you turn off the power in Hibernation Mode, the computer will take a
moment to save the current data in memory to the hard disk drive. During
this time, the Hard Disk Drive/Optical Disc Drive indicator will glow.

After you turn off the computer, and the content of memory has been saved
to the hard disk drive, turn off the power to any peripheral devices.

Do not turn the computer or devices back on immediately. Wait a moment
to let all capacitors fully discharge.

Restarting the computer

Certain conditions require that you reset the computer, for example if:

■ You change certain computer settings.

■ An error occurs and the computer does not respond to your keyboard

commands.

If you need to restart the computer, there are three ways this can be
achieved:

■ Click Start, point to the arrow icon ( ) and then select Restart from

the menu.

■ Press CTRL, ALT and DEL simultaneously (once) to display the menu

window, then select Restart from the Shut down options.

User’s Manual 1-11

■ Press the power button and hold it down for five seconds. Once the

computer has turned itself off, wait between ten and fifteen seconds
before turning the power on again by pressing the power button.

System Recovery Options

There is a hidden partition allocated on the hard disk drive for the System
Recovery Options.

This partition stores files which can be used to repair the system in the
event of a problem.

System Recovery Options

The System Recovery Options feature is installed on the hard disk when
shipped from the factory. The System Recovery Options menu includes
tools to repair startup problems, run diagnostics or restore the system.

See the Windows Help and Support content for more information about
Startup Repair.

The System Recovery Options can also be run manually to repair
problems.

The procedure is as follows. Follow the instructions shown on the on­screen menu.

1. Turn off the computer.

2. While holding the F8 key, turn on the computer.

3. The Advanced Boot Options menu will be displayed.
Use the arrow keys to select Repair Your Computer and press
ENTER.

4. Follow the on-screen instructions.

Getting Started

Check your Windows® manual for more information on backing up your
system (including the system image backup feature).

System Recovery

This section describes the creation of Recovery Media and their use.

Creating Recovery Media

This section describes how to create Recovery Media.

User’s Manual 1-12

Getting Started

■ Be sure to connect the AC adaptor when you create Recovery Media.

■ Be sure to close all other software programs except the Recovery

Media Creator.

■ Do not run software such as screen savers which can put a heavy load

on the CPU.

■ Operate the computer at full power.

■ Do not use power-saving features.

■ Do not write to the media when the virus check software is running.

Wait for it to finish, then disable virus detection programs including any
software that checks files automatically in the background.

■ Do not use utilities, including those intended to enhance hard disk drive

access speed. They may cause unstable operation and damage data.

■ Do not shut down/log off or Sleep/Hibernate while writing or rewriting

the media.

■ Set the computer on a level surface and avoid places subjected to

vibrations such as airplanes, trains, or cars.

■ Do not use on an unstable surface such as a stand.

A recovery image of the software on your computer is stored on the hard
disk drive, and can be copied to either CD, DVD or USB Flash Memory by
using the following steps:

1. Select either blank CD, DVD or USB Flash Memory.
The application will allow you to choose from a variety of different media

onto which the recovery image can be copied including CD-R, CD-RW,
DVD-R, DVD-R DL, DVD-RW, DVD+R, DVD+R DL, DVD+RW and USB
Flash Memory.

■ Please note that some of the above media may not be compatible with

the optical disc drive installed into your computer. You should therefore
verify the optical disc drive supports the blank media you have chosen
before proceeding.

■ USB Flash Memory will be formatted and all the data in the USB Flash

Memory will be lost when proceeding.

2. Turn on your computer and allow it to load the Windows 7 operating
system from the hard disk drive as normal.

3. Insert the media into the computer.

■ Insert the first blank disc into the optical disc drive tray, or

Insert the USB Flash Memory into one available USB port

4. Double click the Recovery Media Creator icon on the Windows 7
desktop, or select the application from Start Menu.

5. After Recovery Media Creator starts, select the type of media and the
title you wish to copy, and then click the Create button.

User’s Manual 1-13

Getting Started

Restoring the pre-installed software from the Recovery hard disk
drive

A portion of the total hard disk drive space is configured as a hidden
recovery partition. This partition stores files which can be used to restore
pre-installed software in the event of a problem.

If you subsequently set up your hard disk drive again, do not change,
delete or add partitions in a manner other than specified in the manual,
otherwise you may find that space for the required software is not available.

In addition, if you use a third-party partitioning program to reconfigure the
partitions on your hard disk drive, you may find that it becomes impossible
to setup your computer.

When the sound mute feature has been activated by pressing the FN +
ESC key, be sure to disable this to allow sounds to be heard before starting

the restore process. Please refer to Chapter 5, The Keyboard, for further
details.

You can not use System Recovery Options if restoring the pre-installed
software without System Recovery Options.

When you reinstall the Windows operating system, the hard disk will be
reformatted and all data will be lost.

1. Turn off your computer.

2. While holding down 0 (zero) key on the keyboard, turn on your
computer.

3. A menu will be displayed from which you should follow the on-screen
instructions.

Restoring the pre-installed software from your created Recovery
Media

If the pre-installed files are damaged, you are able to either use the
Recovery Media you have created or the hard disk drive recovery process
to restore the computer to the state it was in when you originally received it.
To perform this restoration, follow the steps below:

When the sound mute feature has been activated by pressing the FN +
ESC key, be sure to disable this to allow sounds to be heard before starting

the restore process. Please refer to Chapter 5, The Keyboard, for further
details.

You can not use System Recovery Options if restoring the pre-installed
software without System Recovery Options.

User’s Manual 1-14

Getting Started

When you reinstall the Windows operating system, the hard disk will be
reformatted and all data will be lost.

1. Load the Recovery Media into the computer and turn off the computer's
power.

2. While holding down F12 key on the keyboard, turn on your computer ­when the TOSHIBA Leading Innovation >>> logo screen
appears, release the F12 key.

3. Use the up and down cursor key to select the appropriate option from
the menu according to your actual recovery media. Please refer to the

Boot Setting section in Chapter 7, HW Setup for further information.

4. A menu will be displayed from which you should follow the on-screen
instructions.

When drivers/utilities are installed, you can setup the respective
drivers/utilities from the following place. To open the setup files, Click Start

-> All Programs -> TOSHIBA -> Applications and Drivers.

User’s Manual 1-15

The Grand Tour

This chapter identifies the various components of the computer - it is
recommended that you become familiar with each before you operate the
computer.

Legal Footnote (Non-applicable Icons)

For more information regarding Non-applicable Icons, please refer to the
Legal Footnotes section in Appendix F.

Please handle your computer carefully to avoid scratching or damaging the
surface.

Front with the display closed

The following figure shows the computer’s front with its display panel in the
closed position.

Chapter 2

1

1. System indicators 4. Wireless indicators*

2. Memory media slot 5. Stereo speakers

3. Wireless communication switch* 6. Microphone*

* Provided with some models.
Product appearance depends on the model you purchased.

Figure 2-1 Front of the computer with display panel closed

User’s Manual 2-1

2 3

4

5

The Grand Tour

System indicators These LED indicators allow you to monitor the

status of various computer functions and are
described in more detail within the System

indicators section.

Memory media slot This slot lets you insert an

SD™/SDHC™/SDXC™ memory card,
miniSD™/microSD™ Card, Memory Stick

®

(Duo™/PRO™/PRO Duo™/Micro™), xD-Picture
Card™ and MultiMediaCard™. Refer to the

Optional devices section in Chapter 3, Hardware,

Utilities and Options.

Keep foreign metal objects, such as screws, staples and paper clips, out of
the Memory media slot. Foreign metal objects can create a short circuit,
which can cause damage and fire, possibly resulting in serious injury.

Wireless
communication
switch

Slide this switch to the left to turn off Wireless
LAN and Bluetooth functions. Slide it to the right
to turn on the functions.

Only some models are equipped with Bluetooth
and Wireless LAN functions.

■ Do not use the Wireless LAN (Wi-Fi®) or Bluetooth functionalities near

a microwave oven or in areas subject to radio interference or magnetic
fields. Interference from a microwave oven or other source can disrupt
Wi-Fi or Bluetooth operation.

■ Turn all wireless functionalities off when near a person who may have a

cardiac pacemaker implant or other medical electric device. Radio
waves may affect pacemaker or medical device operation, possibly
resulting in serious injury. Follow the instruction of your medical device
when using any wireless functionality.

■ Always turn off wireless functionality if the computer is near automatic

control equipment or appliances such as automatic doors or fire
detectors. Radio waves can cause malfunction of such equipment,
possibly resulting in serious injury.

Wireless indicators These LED indicators allow you to monitor the

status of Bluetooth and Wireless LAN functions
and are described in more detail within the

Wireless indicators section.

User’s Manual 2-2

The Grand Tour

Stereo speakers The speakers emit sound generated by your

software as well as audio alarms, such as low
battery condition, generated by the system.

Left side

Microphone A built-in microphone allows you to import and

record sounds for your application - please refer
to the Sound System section in Chapter 4,
Operating Basics for more information.

Some models are equipped with a built-in
microphone.

The following figure shows the computer’s left side.

4

2

1

1. Universal Serial Bus (USB 2.0) port 4. ExpressCard slot or PC Card slot*

2. eSATA/USB combo port* 5. Mini DisplayPort*

3. Cooling vents

* Provided with some models.
Product appearance depends on the model you purchased.

Figure 2-2 The left side of the computer

3

5

Universal Serial Bus
(USB 2.0) port

One Universal Serial Bus port, which complies to
the USB 2.0 standard, is provided on the left
hand side of the computer. The ports with the
icon ( ) has Sleep and Charge function.

eSATA/USB combo
port

One eSATA/USB combo port, which complies to
the USB 2.0 standard, is provided on the left
hand side of the computer. This port has eSATA
(External Serial ATA) function.

Keep foreign metal objects, such as screws, staples and paper clips, out of
the eSATA/USB combo port. Foreign metal objects can create a short
circuit, which can cause damage and fire, possibly resulting in serious
injury.

User’s Manual 2-3

The Grand Tour

Please note that it is not possible to confirm the operation of all functions of
all USB devices that are available. In view of this it may be noted that some
functions associated with a specific device might not operate properly.

Cooling vents The cooling vents help the processor avoid from

overheating.

Do not block the cooling vents. Keep foreign metal objects, such as
screws, staples and paper clips, out of the cooling vents. Foreign metal
objects can create a short circuit, which can cause damage and fire,
possibly resulting in serious injury.

ExpressCard slot This slot allows you to install a single

ExpressCard device.

PC Card slot This slot can accommodate a single Type II, 16-

bit or 32-bit (CardBus) PC Card device.

PC Card eject button This button is used in order to remove a PC Card

from within the computer.

Keep foreign metal objects, such as screws, staples and paper clips, out of
the PC Card slot. Foreign metal objects can create a short circuit, which
can cause damage and fire, possibly resulting in serious injury.

Mini DisplayPort This port is capable of driving resolutions up to

2560x1600. With a suitable adapter, Mini
DisplayPort may be used to drive displays with a
HDMI or DVI interface.

Right side

The following figure shows the computer’s right side.

3

2

1

1. Headphone jack 3. Universal Serial Bus (USB 2.0) ports

2. Microphone jack 4. Optical disc drive*

* Provided with some models.
Product appearance depends on the model you purchased.

Figure 2-3 The right side of the computer

User’s Manual 2-4

4

The Grand Tour

Headphone jack A 3.5 mm mini headphone jack enables

connection of stereo headphones.

Back

Microphone jack A 3.5 mm mini microphone jack enables

connection of a three-conductor mini jack for
monaural microphone input.

Universal Serial Bus
(USB 2.0) ports

Two Universal Serial Bus ports, which comply to
the USB 2.0 standard, are provided on the right
hand side of the computer.

Keep foreign metal objects, such as screws, staples and paper clips, out of
the USB connectors. Foreign metal objects can create a short circuit,
which can cause damage and fire, possibly resulting in serious injury.

Please note that it is not possible to confirm the operation of all functions of
all USB devices that are available. In view of this it may be noted that some
functions associated with a specific device might not operate properly.

Optical disc drive The computer may be configured with a DVD-

ROM or DVD Super Multi drive.

The following figure shows the computer’s back.

1

1. Security lock slot 5. Modem jack*

2. External monitor port 6. LAN jack

3. Serial port* 7. LAN active indicator (orange)

4. DC IN 15V jack 8. Link indicator (green)

* Provided with some models.
Product appearance depends on the model you purchased.

Figure 2-4 The back of the computer

User’s Manual 2-5

5

4

3

2

The Grand Tour

Security lock slot A security cable can be attached to this slot and

then connected to a desk or other large object in
order to deter theft of the computer.

External monitor
port

This port provides 15-pin, analog VGA port.
This port allows you to connect an external

monitor to the computer.

Serial port Use this 9-pin port to connect serial devices such

as an external modem, serial mouse or serial
printer.

Some models are equipped with a serial port.

DC IN 15V jack The AC adaptor connects to this jack in order to

power the computer and charge its internal
batteries. Please note that you should only use
the model of AC adaptor supplied with the
computer at the time of purchase - using the
wrong AC adaptor can cause damage to the
computer.

Modem jack The modem jack lets you use a modular cable to

connect the modem directly to a telephone line.
Some models are equipped with a modem jack.

■ Connection to any communication line other than an analog phone line

could cause a PC system failure.

■ Connect the built-in modem only to ordinary analog phone lines.

■ Never connect the built-in modem to a digital line (ISDN).

■ Never connect the built-in modem to the digital connector on a

public telephone or to a digital private branch exchange (PBX).

■ Never connect the built-in modem to a key telephone system for

residences or offices.

■ Avoid using your computer modem with the telephone cable connected

during an electrical storm. There may be a remote risk of electric shock
from lightning.

LAN jack This jack lets you connect to a LAN. The adaptor

has built-in support for Ethernet LAN
(10megabits per second, 10BASE-T), Fast
Ethernet LAN (100 megabits per second,
100BASE-TX) or Gigabit Ethernet LAN (1000
megabits per second, 1000BASE-T). Refer to
Chapter 4, Operating Basics, for details.

User’s Manual 2-6

The Grand Tour

■ Do not connect any cable other than a LAN cable to the LAN jack. It

could cause damage or malfunction.

■ Do not connect the LAN cable to a power supply. It could cause

damage or malfunction.

Underside

The following figure shows the underside of the computer. You should
ensure that the display is closed before the computer is turned over to
avoid causing any damage.

LAN active indicator
(orange)

Link indicator
(green)

This indicator may glow orange when the
computer is connected to a LAN and the LAN is
functioning properly.

This indicator may glow green when the
computer is connected to a LAN and the LAN is
functioning properly.

1

2

3

4

1. Battery lock 3. Battery pack

2. Battery release latch 4. Memory module slot

Product appearance depends on the model you purchased.

Figure 2-5 The underside of the computer

Battery lock Slide the battery lock to release the battery pack

ready for removal.

Battery release latch Slide and hold this latch into its 'Unlock' position

in order to release the battery pack for removal.
For more detailed information on removing the
battery pack please refer to Chapter 6, Power

and Power-Up Modes.

User’s Manual 2-7

Battery pack The battery pack provides power to the computer

Memory module slot The memory module slot allows for the

Front with the display open

This section shows the computer with the display panel open. In order to
open the display, lift the display panel up and position it at a comfortable
viewing angle for you.

4

The Grand Tour

when the AC adaptor is not connected. For more
detailed information on the use and operation of
the battery pack please refer to Chapter 6, Power

and Power-Up Modes.

installation, replacement and removal of
additional memory module.

Refer to the Additional memory module section in
Chapter 3, Hardware, Utilities and Options.

3

2

1

10

9

8

7
5
6

11

Figure 2-6 The front of the computer with the display panel open (A4 size keyboard)

User’s Manual 2-8

6

12

14

13

The Grand Tour

1. Wireless LAN and Bluetooth antennas (not shown)* 8. eco button

2. Web Camera* 9. TOSHIBA Presentation button

3. Web Camera LED* 10. Volume up/down buttons

4. Display screen 11. Keyboard

5. LCD Sensor switch (not shown) 12. Touch Pad

6. Display hinges 13. Touch Pad control buttons

7. Power button 14. Fingerprint Sensor*

* Provided with some models.
Product appearance depends on the model you purchased.

Wireless LAN
antennas

Some computers in this series are equipped with
the Wireless LAN antennas.

Bluetooth antenna Some computers in this series are equipped with

a Bluetooth antenna.

Web Camera LED

The Web Camera LED glows when the Web
Camera is operating.

Web Camera Web Camera is a device that allows you to

record video or take photographs with your
computer. You can use it for video chatting or
video conferences using a communication tool
such as Windows Live Messenger. TOSHIBA
Web Camera Application will help you to add
various video effects to your video or photograph.

Enables the transmission of video and use of
video chat via the internet using specialized
applications.

Some models are equipped with a Web Camera.
Please refer to the Web Camera section in

Chapter 4, Operating Basics.

Display hinges The display hinges allow the display panel to be

position at a variety of easy-to-view angles.

Display screen Please be aware that, when the computer is

operating on the AC adaptor, the image
displayed on the internal screen will be
somewhat brighter than when it operates on
battery power. This difference in brightness
levels is intended to save power when operating
on batteries. For more information on the
computer's display, please refer to the Display

Controller and Video mode section in Appendix

B.

Power button Press this button to turn the computer's power on

and off.

User’s Manual 2-9

The Grand Tour

eco button Press this button to launch the TOSHBIA eco

Utility. This button changes "On" and "Off" of eco
Mode. When eco Mode is "On", the icon turns
green. When eco Mode is "Off", the icon turns
gray.

The TOSHIBA eco Utility is not supported by
Windows

®

XP operating system.

TOSHIBA
Presentation button

The TOSHIBA Presentation button has the same
functionality as the Connect display button in the
Mobility Center.

Some models are equipped with a TOSHIBA
Presentation button.

volume down button Press this button to decrease the volume.

volume up button Press this button to increase the volume.

Keyboard Your computer may intergrated with two kinds of

keyboards: A4 size keyboard which provides the
embedded numeric overlay keys, dedicated
cursor control overlay keys, and and
Keys; full size keyboard which provides
dedicated numeric keys, dedicated cursor control
keys, and and Keys. Refer to Chapter 5,

The Keyboard, for details.

Touch Pa d The Touch Pad located in the palm rest is used to

control the movement of the on-screen pointer.
For more information, please refer to the Using

the Touch Pad section in Chapter 4, Operating

Basics.

Touch Pad control
buttons

The control buttons located below the Touch Pad
allow you to select menu items or manipulate text
and graphics as designated by the on-screen
pointer.

User’s Manual 2-10

The Grand Tour

Indicators

Fingerprint Sensor This sensor enables you to enroll and recognize

a fingerprint.
For detailed information on Fingerprint Sensor,

refer to Chapter 4, Using the Fingerprint Sensor.
Some models are equipped with a Fingerprint

Sensor.

LCD Sensor switch This switch senses when the display panel is

either closed or opened and activates the Panel
Power Off/On feature as appropriate. For
example, when you close the display panel the
computer enters Hibernation Mode and shuts
itself down and then, when you next open the
display, the computer will automatically start up
and return you to the application you were
previously working on.

You can specify within the Power Options. To
access it, click Start -> Control Panel -> System
and Security -> Power Options.

Do not put any magnetic objects close to this switch as they may cause the
computer to automatically enter Hibernation Mode and shut down even if
the Panel Power Off feature is disabled.

This section explains indicator functions.

System indicators

LED system indicators next to their respective icons, glow when specific
computer operations are in progress.

Figure 2-7 System indicators

User’s Manual 2-11

The Grand Tour

DC IN The DC IN indicator normally glows green when

power is being correctly supplied from the AC
power adaptor. However, If the output voltage
from the adaptor is abnormal, or if the computer's
power supply malfunctions, this indicator will
flash orange.

Power The Power indicator normally glows green when

the computer is turned on. However, if you turn
the computer off into Sleep Mode, this indicator
will flash orange - approximately two second on,
two seconds off - both while the system is
shutting down and while it remains turned off.

Battery The Battery indicator shows the condition of the

battery's charge - green indicates the battery is
fully charged, orange indicates the battery is
charging, and flashing orange indicates a low
battery condition. Please refer to Chapter 6,

Power and Power-Up Modes for more

information on this feature.

Hard Disk Drive/
Optical Disc Drive

The Hard Disk Drive/Optical Disc Drive
indicator blinks green whenever the computer is
accessing the built-in hard disk drive, optical disc
drive or eSATA device.

Memory media slot The Memory media slot indicator blinks green

when the computer is accessing the Memory
media slot.

Wireless indicators

Wireless indicators next to their respective icons, glow when specific
computer operations are in progress.

Figure 2-8 Wireless indicators

Wireless
communication

Wireless WAN This indicator always show off with no effect.

The Wireless communication indicator glows
orange when the Bluetooth and Wireless LAN
functions are turned on.

Only some models are equipped with Bluetooth
and Wireless LAN functions.

User’s Manual 2-12

Keyboard indicators

A4 size keyboard

The following figures show the positions of the CAPS LOCK indicator and
the keypad overlay indicators which show the following conditions:

■ When the CAPS LOCK indicator glows, the keyboard will produce

capitals when any letter is typed.

■ When the Arrow Mode indicator glows, the keypad overlay allows you to

use cursor functions.

■ When the Numeric Mode indicator glows, the keypad overlay allows

you to enter numbers.

1

1. CAPS LOCK indicator

Figure 2-9 CAPS LOCK indicator

The Grand Tour

CAPS LOCK This indicator glows green when letter keys are

locked into their uppercase format.

1

1. Arrow mode indicator 2. Numeric mode indicator

Figure 2-10 Keypad overlay indicators

User’s Manual 2-13

2

The Grand Tour

Arrow mode When the Arrow mode indicator lights green,

you can use the gray labeled keys on the keypad
overlay as cursor keys. Please refer to the

Keypad overlay for A4 size keyboard section in

Chapter 5, The Keyboard for more information.

Numeric mode When the Numeric mode indicator lights green,

you can use the gray labeled keys on the keypad
overlay for number entry. Please refer to the

Keypad overlay for A4 size keyboard section in

Chapter 5, The Keyboard for more information.

Full size keyboard

The following figures show the positions of the CAPS LOCK indicator and
the NUM LOCK indicators which show the following conditions:

■ When the CAPS LOCK indicator glows, the keyboard will produce

capitals when any letter is typed.

■ When the NUM LOCK indicator glows, the ten key allows you to enter

numbers.

2

1

1. CAPS LOCK indicator

Figure 2-11 Keypad indicators

2. NUM LOCK indicator

CAPS LOCK This indicator glows green when letter keys are

locked into their uppercase format.

NUM LOCK When the NUM LOCK indicator glows, you can

use the number keys on the keyboard for number
entry.

User’s Manual 2-14

Optical disc drives

The computer may be installed with a DVD-ROM or DVD Super Multi drive.
When the computer is accessing a CD/DVD, an indicator on the drive
glows.

Some models are equipped with an optical disc drive.
For information on loading and unloading discs refer to the Using optical

disc drives section in Chapter 4, Operating Basics.

Writable discs

This section describes the types of writable CD/DVD discs. Check the
specifications of your drive to see the types of discs it can write. Use
TOSHIBA Disc Creator to write compact discs. Refer to Chapter 4,

Operating Basics.

CDs

■ CD-R discs can be written only once. The recorded data cannot be

erased or changed.

■ CD-RW discs including multi speed CD-RW discs, high-speed CD-RW

discs and ultra-speed CD-RW discs can be recorded more than once.

DVDs

■ DVD-R, DVD+R, DVD-R (Dual Layer) and DVD+R (Double Layer) discs

can be written only once. The recorded data cannot be erased or
changed.

■ DVD-RW, DVD+RW and DVD-RAM discs can be recorded more than

once.

The Grand Tour

Formats

The drives support the following formats.

DVD-ROM drive

The drive supports the formats CD-ROM, DVD-ROM, DVD-Video, CD-DA,
CD-Text, Photo CD

CD-ROM XA Mode 2 (Form1, Form2), Enhanced CD (CD-EXTRA) and
Addressing Method 2.

TM

(single/multi-session), CD-ROM Mode 1, Mode 2,

DVD Super Multi drive Double Layer

The drive supports the formats in addition to the DVD-ROM&CD-R/RW
drive, and DVD-R, DVD-RW, DVD+R, DVD+RW, DVD-RAM, DVD-R DL
(Format1), DVD+R DL.

Some types and formats of DVD-R DL and DVD+R DL discs may be
unreadable.

User’s Manual 2-15

AC adaptor

The AC adaptor can automatically adjust to any voltage ranging from 100 to
240 volts and to a frequency of either 50 or 60 hertz, enabling you to use
this computer in almost all country/region. The adaptor converts AC power
to DC power and reduces the voltage supplied to this computer.

To recharge the battery, simply connect the AC adaptor to a power source
and to the computer. Please refer to Chapter 6, Power and Power-Up

Modes for further information.

The Grand Tour

Figure 2-12 The AC adaptor (2-pin plug)

Figure 2-13 The AC adaptor (3-pin plug)

■ Depending on the model in question, either a 2-pin or 3-pin

adaptor/power lead will be bundled with the computer.

■ Do not use a 3-pin to 2-pin conversion plug.

■ The supplied power cord conforms to safety rules and regulations in

the region the product is bought and should not be used outside of this
region. In order to use the adaptor/computer in other regions, you
should please buy a power cord that conforms to the safety rules and
regulations in that particular region.

Always use the TOSHIBA AC adaptor that was included with your
computer, or use AC adaptors specified by TOSHIBA to avoid any risk of
fire or other damage to the computer. Use of an incompatible AC adaptor
could cause fire or damage to the computer possibly resulting in serious
injury. TOSHIBA assumes no liability for any damage caused by use of an
incompatible adaptor.

User’s Manual 2-16

Chapter 3

Hardware, Utilities and Options

Hardware

This section describes the hardware of your computer.
The actual specifications may vary depending on the model you

purchased.

Processor

CPU Your computer is equipped with one processor

and processor type varies depending on model.
To check which type of processor is included in

your model, open the TOSHIBA PC Diagnostic
Tool Utility by clicking Start -> All Programs ->
TOSHIBA -> Utilities -> PC Diagnostic Tool.

Legal Footnote (CPU)

For more information on the CPU, please refer to the Legal Footnotes
section in Appendix F.

User’s Manual 3-1

Memory

Hardware, Utilities and Options

Memory slots The momory slot allows for the installation,

Video RAM The memory in a computer's graphics adaptor,

If your computer is configured with more than 3 GB memory, the memory
might be displayed as approximately 3 GB only (depending on the
computer’s hardware specifications).

This is correct because the operating system usually displays the available
memory instead of the physical memory (RAM) built into the computer.

Various system components (like the video adapter’s GPU and PCI
devices like Wireless LAN, etc.) require their own memory space. Since a
32-bit operating system cannot address more than 4 GB of memory, these
system resources overlap the physical memory. It is a technical limitation
that the overlapped memory is not available to the operating system. Even
though some tools might display the actual physical memory built into your
computer, the memory available to the operating system will still be
approximately 3 GB only.

Computers configured with a 64-bit operating system can address 4GB or
more of system memory.

replacement and removal of additional memory
module.

1 GB, 2 GB or 4 GB memory modules can be
installed in the computer's two memory slots for a
maximum of 8 GB system memory. The actual
amount of useable system memory will be less
than the installed memory modules.

used to store the image displayed on a bitmap
display.

The amount of Video RAM available is
dependent on the computer's system memory.

Start -> Control Panel -> Appearance and
Personalization -> Display -> Adjust
resolution.

The amount of Video RAM can be verified by
clicking the Advanced Settings button in the
Screen Resolution window.

Legal Footnote (Memory (Main System))

For more information regarding Memory (Main System), please refer to the
Legal Footnotes section in Appendix F.

Power

Battery pack The computer is powered by one rechargeable

lithium-ion battery pack.

User’s Manual 3-2

Hardware, Utilities and Options

Legal Footnote (Battery Life)

For more information regarding Battery Life, please refer to the Legal
Footnotes section in Appendix F.

RTC battery The internal RTC battery backs up the Real Time

AC adaptor The AC adaptor provides power to the system

Clock (RTC) and calendar.

and recharges the batteries when they are low. It
comes with a detachable power cord which will
either have a 2-pin or 3-pin plug enclosure.

As the AC adaptor is universal, it can receive a
range of AC voltages from 100 to 240 volts,
however you should note that the output current
varies among different models. Using the wrong
adaptor can damage your computer. Refer to the

AC adaptor section in Chapter 2, The Grand

To ur .

Disks

Hard disk drive or
Solid state drive

■ In this manual, the word "HDD" or "Hard disk drive" also refers to the

SSD unless otherwise stated.

■ SSD is a large-capacity storage media which uses Solid-State Memory

in place of a magnetic disk of the hard disk.

The size of the hard disk drive varies depending
on the model.

To check which type of HDD is included in your
model, open the TOSHIBA PC Diagnostic Tool
Utility by clicking Start -> All Programs ->
TOSHIBA -> Utilities -> PC Diagnostic Tool.

Please note that part of the hard disk's overall
capacity is reserved as administration space.
Additional HDD drive sizes may be introduced.

Under certain unusual conditions of prolonged non-use and/or exposure to
high temperatures, the SSD may be vulnerable to data retention errors.

Legal Footnote (Hard Disk Drive (HDD) Capacity)

For more information regarding Hard Disk Drive (HDD) Capacity, please
refer to the Legal Footnotes section in Appendix F.

User’s Manual 3-3

Optical disc drive

Hardware, Utilities and Options

Drive The following optical disc drive may be pre-

2.6GB and 5.2GB DVD-RAM media cannot be read from or written to.

installed in this computer.

■ DVD-ROM drive

■ DVD Super Multi drive Double Layer

Display

The computer's internal display panel supports high-resolution video
graphics and can be set to a wide range of viewing angles for maximum
comfort and readability.

Display panel

39.6cm (15.6”) LCD screen, 16 million colors,
with one of the following resolutions:

■ HD, 1366 horizontal x 768 vertical pixels

■ HD+, 1600 horizontal x 900 vertical pixels

Legal Footnote (LCD)

For more information regarding the LCD, please refer to the Legal
Footnotes section in Appendix F.

Graphics controller The graphics controller maximizes display

performance. Refer to Display Controller and

Video mode section in Appendix B for more

information.

Legal Footnote (Graphics Processing Unit ("GPU"))

For more information regarding the Graphics Processing Unit ("GPU"),
please refer to the Legal Footnotes section in Appendix F.

Sound

Sound system The integrated sound system provides support

for the computer's internal speakers and
microphone, as allowing an external microphone
and headphones to be connected via the
appropriate jacks.

User’s Manual 3-4

Multimedia

Hardware, Utilities and Options

Web Camera Web Camera is a device that allows you to

record video or take photographs with your
computer. You can use it for video chatting or
video conferences using a communication tool
such as Windows Live Messenger. TOSHIBA
Web Camera Application will help you to add
various video effects to your video or photograph.

Please refer to the Web Camera section in
Chapter 4, Operating Basics.

Communications

Modem The integrated modem provides capability for

LAN The computer has built-in support for Ethernet

Bluetooth Some computers in this series have Bluetooth

Wireless LAN Some computers in this series are equipped with

data and fax communications that support the
V.90 (V.92) standards and includes a modem
jack for connection to the telephone line. Please
note that both the V.90 and V.92 standards are
only supported in the USA, Canada, United
Kingdom, France, Germany and Australia - only
the V.90 standard is supported in other regions.
You should also be aware that the speed of data
and fax transfer will depend on the analog
telephone line conditions.

Some models are equipped with the integrated
modem.

LAN (10 megabits per second, 10BASE-T), Fast
Ethernet LAN (100 megabits per second,
100BASE-TX) or Gigabit Ethernet LAN (1000
megabits per second, 1000BASE-T).

wireless communication function which
eliminates the need for cables between
electronic devices such as computers, printers
and mobile phones. When it is enabled,
Bluetooth provides the wireless personal area
network environment which is safe and
trustworthy, that is quick and easy.

a Wireless LAN module that is compatible with
other LAN systems based on Direct Sequence
Spread Spectrum/Orthogonal Frequency Division
Multiplexing radio technology that complies with
the IEEE 802.11 Standard.

User’s Manual 3-5

Legal Footnote (Wireless LAN)

For more information regarding Wireless LAN, please refer to the Legal
Footnotes section in Appendix F.

Special features

The following features are either unique to TOSHIBA computers or are
advanced features which make the computer more convenient to use.

Access each function using the following procedures.
*1 To access the Power Options, click Start -> Control Panel -> System

and Security -> Power Options.

Hardware, Utilities and Options

eco button Press this button to launch the TOSHBIA eco

Utility. This button changes "On" and "Off" of eco
Mode. When eco Mode is "On", the icon turns
green. When eco Mode is "Off", the icon turns
gray.

TOSHIBA
Presentation button

The TOSHIBA Presentation button has the same
functionality as the Connect display button in the
Mobility Center.

Some models are equipped with a TOSHIBA
Presentation button.

Hot keys Hot keys are specific key combinations that let

you quickly change the system configuration
directly from the keyboard without running a
system program.

Display automatic
power off

*1

This feature automatically cuts off power to the
computer's display panel when there is no
keyboard input for a specified time, with power
being restored the next time a key is pressed.
This can be specified in the Power Options.

HDD automatic
power off

*1

This feature automatically cuts off power to the
hard disk drive when it is not accessed for a
specified time, with power being restored when
the hard disk drive is next accessed. This can be
specified in the Power Options.

System automatic
Sleep/Hibernation

*1

Mode

This feature automatically shuts down the system
into either Sleep Mode or Hibernation Mode when
there is no input or hardware access for a
specified time. This can be specified in the Power
Options.

User’s Manual 3-6

Hardware, Utilities and Options

Keypad overlay A ten-key numeric keypad is integrated into the

A4 size keyboard. Please refer to the Keypad

overlay for A4 size keyboard section in Chapter

5, The Keyboard, for information on using this
feature.

Power on password Two levels of password security, supervisor and

user, are available to prevent unauthorized
access to your computer.

Instant security A specific hot key function automatically locks the

system providing data security.

Intelligent power
supply

*1

A microprocessor in the computer's intelligent
power supply detects the battery's charge,
automatically calculates the remaining battery
capacity and protects electronic components
from abnormal conditions such as a voltage
overload from the AC adaptor. This can be
specified in the Power Options.

*1

Battery save mode

This feature lets you configure the computer in
order to save battery power. This can be
specified in the Power Options.

Panel power on/off

*1

This feature automatically turns power to the
computer off when the display panel is closed,
and turns it back on when the display panel is
opened. This can be specified in the Power
Options.

Low battery
automatic

Hibernation Mode

When battery power is exhausted to the point that
computer operation cannot be continued, the

*1

system automatically enters Hibernation Mode
and shuts itself down. This can be specified in the
Power Options.

Heat dispersal

*1

To protect against overheating, the processor has
an internal temperature sensor so that, if the
computer's internal temperature rises to a certain
level, the cooling fan is turned on or the
processing speed is lowered. This can be
specified in the Power Options.

Hibernation Mode This feature lets you turn off the power to the

computer without exiting from your software. The
contents of main memory are automatically
saved to the hard disk drive so that when you
next turn the power on again, you can continue
working right where you left off. Refer to the

Turning off the power section in Chapter 1,

Getting Started, for more details.

User’s Manual 3-7

Hardware, Utilities and Options

Sleep Mode If you have to interrupt your work, you can use

this feature to allow you to turn off power to the
computer without exiting from your software. Data
is maintained in the computer's main memory so
that when you next turn on the power, you can
continue working right where you left off.

Sleep and Charge
function

USB Wakeup
function

TOSHIBA PC Health
Monitor

This feature allows you to charge USB­compatible external devices such as mobile
phones or portable digital music players via the
USB port when your computer is in Sleep Mode,
Hiberantion Mode or in the shutdown state.

This function is worked by the TOSHIBA Sleep
Utility. For more information, please refer to the

Using the TOSHIBA Sleep Utility section in

Chapter 4, Operating Basics.

This function restores the computer from Sleep
Mode depending on the external devices
connected to the USB ports.

For example, if a mouse or USB keyboard is
connected to a USB port, moving the
mouse/keyboard will wakeup the computer.

The "USB Wakeup function" operates under
Windows 7 operating system and it works for all
USB ports.

The TOSHIBA PC Health Monitor application
proactively monitors a number of system
functions such as power consumption, battery
health and system cooling, informing you of
significant system conditions. This application
recognizes the system and individual component
serial numbers and will track specific activities
related to their usage.

Refer to Appendix E, TOSHIBA PC Health

Monitor.

User’s Manual 3-8

Utilities and Applications

This section describes the pre-installed utilities that come with the
computer and details how to start them. For further information on their
operation, you may refer to each utility's online manual, help files or
README.TXT file (if applicable).

You may not have all the utilities or applications listed below depending on
the model you purchased.

Hardware, Utilities and Options

TOSHIBA Power
Saver

TOSHIBA Button
Support

TOSHIBA Button Support cannot be used in models that are not equipped
with eco button and TOSHIBA Presentation button.

TOSHIBA PC
Diagnostic Tool

TOSHIBA Password
Utility

TOSHIBA Flash
Cards

HW Setup This utility allows you to customize your

TOSHIBA
Accessibility

TOSHIBA Power Saver provides you with the
features of more various power supply
managements.

This utility controls the following computer button
functions.

■ eco button

■ Presentation button

The starting application from the button can be
changed.

The TOSHIBA PC Diagnostic Tool will display
basic system configuration information and allow
the functionality of some of the computer's built­in hardware devices to be tested.

The TOSHIBA Password utility allows you to set
a password in order to restrict access to the
computer.

The TOSHIBA Flash Cards provide a quick way
to modify selected system functions.

■ Hot key function

hardware settings according to the way you work
with the computer and the peripherals you use.

The TOSHIBA Accessibility utility provides
support to movement impaired users when they
need to use the TOSHIBA Hot-key functions. In
use, the utility allows you to make the FN key
'sticky', that is you can press it once, release it,
and they press one of the 'Function' keys in
order to access its specific function. When set,
the FN key will remain active until another key is
pressed.

User’s Manual 3-9

Hardware, Utilities and Options

Fingerprint Utility This product has a fingerprint utility installed for

the purpose of enrolling and recognizing
fingerprints which can then be linked to a
username and password in order to remove the
need to input these details from the keyboard.
Just by swiping an enrolled finger against the
fingerprint sensor, the following functions will be
enabled:

■ Logon to Windows and access a security

enabled homepage through Internet Explorer.

■ Files and folders can be encrypted/decrypted

and third party access to them is prevented.

■ Disable the password-protected screen-saver

when returning from a power-saving mode
such as Sleep Mode.

■ Authentication of the User Password (and, if

applicable, the HDD(Hard Disk Drive)
Password) when booting up the computer
(Power-on Security).

■ Single Sign-on feature

Fingerprint security cannot be used in models that do not have a fingerprint
module installed.

TOSHIBA Face
Recognition

TOSHIBA Face Recognition uses a face
verification library to verify the face data of users
when they log in to Windows. If the verification is
successful, the user will be logged into Windows
automatically. The user can thus avoid having to
enter a password or the like, which makes the
login process easier.

For more information, please refer to the Using

the TOSHIBA Face Recognition section in

Chapter 4, Operating Basics.

User’s Manual 3-10

Hardware, Utilities and Options

TOSHIBA VIDEO
PLAYER

The player lets you view DVD movies, or video
content recorded using home video camcorders.
You can play DVD-Video, DVD-R and video files.

It has an on-screen interface and functions. Click

Start -> All Programs -> TOSHIBA VIDEO
PLAYER -> TOSHIBA VIDEO PLAYER.

For more information, please refer to the

TOSHIBA VIDEO PLAYER section in Chapter 4,

Operating Basics.

Bluetooth Stack for
Windows by
TOSHIBA

This software enables communication between
the computer and external Bluetooth devices
such as printers and mobile phones.

Bluetooth functions cannot be used in models that do not have a Bluetooth
module installed.

TOSHIBA Assist TOSHIBA Assist is a graphical user interface that

provides access to specific tools, utilities and
applications that make the use and configuration
of the computer easier.

TOSHIBA ConfigFree TOSHIBA ConfigFree is a suite of utilities that

improve the ease and control of communication
devices and network connections, help in the
identification of communication problems and
allow the creation of profiles if you need to switch
between different locations and communication
networks. To access this utility, click Start -> All

Programs -> TOSHIBA -> ConfigFree.

TOSHIBA eco Utility This PC is equipped with "eco mode". This mode

slightly lowers performance of some devices to
reduce electric power consumption. You can
realize measurable power savings by using it
continuously. TOSHIBA eco Utility helps you
monitor your power savings by showing
approximate real time power consumption.
Furthermore, it shows approximate accumulated
power consumption and approximate
accumulated power savings when using eco
mode daily, weekly, and monthly. You can track
power savings by using eco mode continuously.

User’s Manual 3-11

Hardware, Utilities and Options

TOSHIBA Disc
Creator

TOSHIBA DVD-RAM
Utility

TOSHIBA HDD/SSD
Alert Utility

TOSHIBA Service
Station

TOSHIBA Bulletin
Board

You can create CD's and DVD's in a number of
formats including audio CD's that can be played
on a standard CD player, and data CD's/DVD's
which can store copies of the files and folders on
your computer's hard disk drive. This software
can be used on models with a DVD Super Multi
drive.

To start this utility, click Start -> All Programs ->

TOSHIBA -> CD&DVD Applications -> Disc
Creator.

This utility has the function of Physical Format
and Write-Protect to DVD-RAM. This utility is
contained the setup module of TOSHIBA Disc
Creator. To start this utility, click Start -> All

Programs -> TOSHIBA -> CD&DVD
Applications -> DVD-RAM Utility.

This utility includes wizard functions to monitor
the Disk Drive operating status and execute the
system backup.

To access the utility, click Start -> All Programs

-> TOSHIBA -> Utilities -> HDD SSD Alert.

This application allows your computer to
automatically search for TOSHIBA software
updates or other alerts from TOSHIBA that are
specific to your computer system and its
programs. When enabled, this application
periodically transmits to our servers a limited
amount of system information, which will be
treated in strict accordance with the rules and
regulations as well as applicable data protection
law.

To access this utility, click Start -> All Programs

-> TOSHIBA -> Utilities -> Service Station.

Bulletin Board is a convenient place to pin things
to visually organize in a fun and creative way.

Simply drag and drop your favorite pictures, files
or notes to pin them on the Board. You can use it
to create thumbnail shortcuts, reminders, to-do
list and so on according to your personal style.

To access this utility, click Start -> All Programs

-> TOSHIBA -> TOSHIBA Bulletin Board.

User’s Manual 3-12

Hardware, Utilities and Options

TOSHIBA ReelTime This application is a graphical history/indexing

tool that enables you to view recently accessed
files in a fun and easy-to-use format. View and
scroll through your history of opened or imported
files via thumbnails in an intuitive user interface.

To access this utility, click Start -> All Programs

-> TOSHIBA -> TOSHIBA ReelTime.

TOSHIBA Wireless
LAN Indicator

TOSHIBA Media
Controller

TOSHIBA Speech
System

Trusted Platform
Module (TPM)

TOSHIBA Wireless LAN Indicator utility displays
the system's Wireless LAN connection status on
the logon screen.

You can quickly check the current Wireless LAN
connection status before logging into Windows.

To change the settings of this utility, click Start ->

All Programs -> TOSHIBA -> Networking ->
Wireless LAN Indicator - Settings.

This application allows you to control your music,
pictures and videos by streaming content to any
compatible device in your home.

To access this utility, click Start -> All Programs

-> TOSHIBA -> TOSHIBA Media Controller ->
TOSHIBA Media Controller.

For more information, please refer to the
TOSHIBA Media Controller Help.

The TOSHIBA Speech System consists of a
voice-composition application (text-to-speech)
that analyzes documents and reads them aloud,
and a speech-recognition application that
recognizes the words you speak into a
microphone. This allows you to control and
operate various Windows programs by voice
command rather than using the keyboard or a
mouse.

To access this utility, click Start -> All Programs

-> TOSHIBA -> Speech System.
For more information, please refer to the

TOSHIBA Speech System Help.

The TPM (Trusted Platform Module) is a security
encryption device for the hard disk drive.

BIOS setup and Infineon TPM Software
Professional Package must be configured in
order to use TPM.

User’s Manual 3-13

To enable TPM through the BIOS setup:

1. Turn on the computer while pressing the F2 key. When the TOSHIBA

Leading Innovation >>> screen appears, release the F2 key.

2. Set the TPM in the Security tab to Enabled.

3. Press the F10 key.

4. Press the Y key to accept the changes. The computer will restart.

In order to change the TPM setting when the Hide TPM setting is currently
set to Yes, switch the Hide TPM setting from Yes to No.

Optional devices

Optional devices can expand the computer's capabilities and its versatility.
This section describes the connection or installation of the following
devices:

Cards/memory

■ ExpressCard/PC Card

■ Memory media slot

■ Secure Digital™ (SD) Card (SD memory card, SDHC memory card,

SDXC memory card, miniSD Card, microSD Card)

■ Memory Stick (Memory Stick, Memory Stick PRO, Memory Stick

Duo, Memory Stick PRO Duo, Memory Stick Micro)

■ xD picture card

■ MultiMediaCard

■ Additional memory module

Hardware, Utilities and Options

Peripheral devices

■ External monitor

■ eSATA

■ Serial port

Other

■ Security lock

ExpressCard

The computer may be equipped with a single ExpressCard slot into which
any ExpressCard device that meets industry standards, either
manufactured by TOSHIBA or another vendor, can be installed. The slot
supports hot plug connection and utilizes the PCI Express interface that
supports the reading and writing of data at a theoretical maximum rate of

2.5Gbps.

User’s Manual 3-14

Hardware, Utilities and Options

Inserting an ExpressCard

The Windows hot-install feature allows you to insert ExpressCards while
the computer is turned on.

Do not insert an ExpressCard while the computer is in Sleep Mode or
Hibernation Mode as you may find that some cards do not work properly.

To insert an ExpressCard, follow the steps as detailed below:

1. Press the Dummy card in order to eject the Dummy card partially out of
the computer.

2. Grasp the Dummy card and draw it.

3. Insert the ExpressCard into the ExpressCard slot on the side of the
computer.

4. Press the ExpressCard gently to ensure a firm connection is made.

1

2

1. ExpressCard slot

Figure 3-1 Inserting the ExpressCard

2. ExpressCard

5. After inserting the ExpressCard you should refer to its documentation
and also check the configuration in Windows in order to ensure that it is
correct.

Removing an ExpressCard

To remove an ExpressCard, follow the steps as detailed below.

1. Open the Safely Remove Hardware icon on the Windows Taskbar.

2. Point to ExpressCard and click the left Touch Pad control button.

3. Press the ExpressCard in order to eject the ExpressCard partially out of
the computer.

4. Grasp the ExpressCard and remove it.

User’s Manual 3-15

Hardware, Utilities and Options

1. ExpressCard

Figure 3-2 Removing the ExpressCard

5. Insert the Dummy card into the ExpressCard slot.

When you do not use an ExpressCard, please be sure to insert a Dummy
card.

PC Card

The computer may be equipped with a single PC Card slot that can
accommodate a Type II format card. Any PC Card that meets industry
standards, either manufactured by TOSHIBA or another vendor, can be
installed as the slot supports 16-bit PC Cards and 32-bit CardBus cards.
For reference, CardBus supports the newer standard of 32-bit PC Cards
and provides superior performance for the greater demands of applications
such as multimedia data transmission.

1

PC Cards can sometimes become hot during computer operation. Before
you remove a PC Card always wait for it to cool. You could get burned
removing a hot PC Card.

Inserting a PC Card

The Windows hot-install feature allows you to insert PC Cards while the
computer is turned on.

Do not insert a PC Card while the computer is in Sleep Mode or
Hibernation Mode as you may find that some cards do not work properly.

To insert a PC Card, follow the steps as detailed below:

1. Insert the PC Card into the PC Card slot on the side of the computer.

2. Press the PC Card gently to ensure a firm connection is made.

User’s Manual 3-16

Hardware, Utilities and Options

1

2

1. PC Card slot

Figure 3-3 Inserting the PC Card

2. PC Card

3. After inserting the PC Card you should refer to its documentation and
also check the configuration in Windows in order to ensure that it is
correct.

Removing a PC Card

To remove a PC Card, follow the steps as detailed below:

1. Open the Safely Remove Hardware icon on the Windows Taskbar.

2. Point to PC Card and click the left Touch Pad control button.

3. Press the PC Card eject button to partially extend it out of the computer.

If the PC Card is not inserted all the way into the computer, the eject button
may not cause it to pop out sufficiently to allows it to be grasped. In this
instance, simply push the PC Card firmly back into the computer and then
press the eject button again.

4. Press the extended PC Card eject button in order to eject the PC Card
partially out of the computer.

5. Grasp the PC Card and remove it.

2

1

1. PC Card eject button

Figure 3-4 Removing the PC Card

User’s Manual 3-17

2. PC Card

Memory media slot

The computer is equipped with a Memory media slot that can
accommodate some kinds of memory media with various memory
capacities so that you can easily transfer data from devices, such as digital
cameras and Personal Digital Assistants.

Keep foreign objects out of the Memory media slot. Never allow metal
objects, such as screws, staples and paper clips, to enter the computer or
Keyboard. Foreign metal objects can create a short circuit, which can
cause computer damage and fire, possibly resulting in serious injury.

■ This Memory media slot supports the following memory media.

■ Secure Digital (SD) Card (SD memory card, SDHC memory card,

SDXC memory card, miniSD Card, microSD Card)

■ Memory Stick (Memory Stick, Memory Stick PRO, Memory Stick

Duo, Memory Stick PRO Duo, Memory Stick Micro)

■ xD picture card

■ MultiMediaCard (MMC™)

■ Please note that an adaptor is required to use miniSD/microSD Card.

■ Please note that an adaptor is required to use Memory Stick Duo,

Memory Stick PRO Duo and Memory Stick Micro.

■ Please note that not all memory media have been tested and verified to

work correctly. Therefore, it is not possible to guarantee that all
memory media will operate properly.

■ The slot does not support Magic Gate functions.

Hardware, Utilities and Options

Secure Digital (SD) Card

Memory Stick

Figure 3-5 Examples of memory media

User’s Manual 3-18

microSD card adaptor and microSD card

xD picture card

MultiMediaCard
(MMC)

Hardware, Utilities and Options

Memory media

This section provides the important safety precautions in order to handle
your memory media.

Points to note about the SD/SDHC/SDXC memory card

SD/SDHC/SDXC memory cards comply with SDMI (Secure Digital Music
Initiative), which is a technology adopted to prevent unlawful copy or
playback of digital music. For this reason, you cannot copy or playback
protected material on another computer or other device, and you may not
reproduce any copyrighted material except for your personal enjoyment.

Below is a simple explanation for distinguishing SD memory cards from
SDHC and SDXC memory cards.

■ SD, SDHC and SDXC memory cards appear the same externally.

However, the logo on SD, SDHC and SDXC memory cards is different,
so pay careful attention to the logo when purchasing.

■ The SD memory card logo is ( ).

■ The SDHC memory card logo is ( ).

■ The SDXC memory card logo is ( ).

■ The maximum capacity of SD memory cards is 2GB. The maximum

capacity of SDHC memory cards is 32GB. The maximum capacity of
SDXC memory cards is 64GB.

Card Type Capacities

SD 8MB, 16MB, 32MB, 64MB, 128MB, 256MB,

SDHC 4GB, 8GB, 16GB, 32GB

SDXC 64GB

512MB, 1GB, 2GB

Memory media format

New media cards are formatted according to specific standards. If you wish
to reformat a media card, be sure to do so with a device that uses media
cards.

Formatting an SD/SDHC/SDXC memory card

SD/SDHC/SDXC memory cards are sold already formatted in conformity to
specific standards. If you reformat an SD/SDHC/SDXC memory card, be
sure to reformat it with a device such as digital camera or digital audio
player that uses the SD/SDHC/SDXC memory cards, not with the format
command provided within Windows.

Should you need to format all areas of the memory card,including the
protected area,you will need to obtain an appropriate application that
applies the copy protection system.

User’s Manual 3-19

Hardware, Utilities and Options

Media care

Observe the following precautions when handling the card.

Card care

■ Do not twist or bend cards.

■ Do not expose cards to liquids or store in humid areas or lay media

close to containers of liquid.

■ Do not touch the metal part of a card or expose it to liquids or let it get

dirty.

■ After using card, return it to its case.

■ The card is designed so that it can be inserted only one way. Do not try

to force the card into the slot.

■ Do not leave a card partially inserted in the slot. Press the card until you

hear it click into place.

Memory card care

■ Set the write-protect switch to the lock position, if you do not want to

record data.

■ Memory cards have a limited lifespan, so it is important to backup

important data.

■ Do not write to a card if the battery power is low. Low power could affect

writing accuracy.

■ Do not remove a card while read/write is in progress.

For more details on using memory cards, see manuals accompanying the
cards.

About the write-protect

The following memory media have a function for protect.

■ SD Card (SD memory card, SDHC memory card, SDXC memory card)

■ Memory Stick (Memory Stick, Memory Stick PRO, Memory Stick Duo,

Memory Stick PRO Duo, Memory Stick Micro)

■ MultiMediaCard (MMC)

Set the write-protect switch to the lock position, if you do not want to record
data.

Inserting a memory media

The following instructions apply to all types of supported media devices. To
insert a memory media, follow the steps as detailed below:

1. Turn the memory media so that the contacts (metal areas) are face
down.

2. Insert the memory media into the Memory media slot on the side of the
computer.

User’s Manual 3-20

Hardware, Utilities and Options

3. Press the memory media gently to ensure a firm connection is made.

1

2

1. Memory media slot

Figure 3-6 Inserting a memory media

2. Memory media

■ Make sure memory media is oriented properly before you insert it. If

you insert the media in wrong direction, you may not be able to remove
it.

■ When inserting memory media, do not touch the metal contacts. You

could expose the storage area to static electricity, which can destroy
data.

■ Do not turn the computer off or switch to Sleep Mode or Hibernation

Mode while files are being copied - doing so may cause data to be lost.

Removing a memory media

The following instructions apply to all types of supported media devices. To
remove a memory media, follow the steps as detailed below:

1. Open the Safely Remove Hardware icon on the Windows Taskbar.

2. Point to memory media and click the left Touch Pad control button.

3. Press the memory media to partially extend it out of the computer.

4. Grasp the media and remove it.

1

2

1. Memory media slot

Figure 3-7 Removing memory media

User’s Manual 3-21

2. Memory media

Hardware, Utilities and Options

■ Make sure the Memory Media slot indicator is out before you remove

the memory media or turn off the computer’s power. If you remove the
memory media or turn off the power while the computer is accessing
the memory media, you may lose data or damage the media.

■ Do not remove the memory media while the computer is in Sleep or

Hibernation Mode. The computer could become unstable or data in the
memory media could be lost.

■ Do not remove only the miniSD/microSD Card while leaving the

adaptor in the Memory Media slot.

Additional memory module

You can install additional memory into the computer in order to increase the
amount of system memory that is available. This section describes how to
install and remove optional memory modules.

■ You should place a mat beneath the computer in order to prevent the

computer's lid from becoming scratched or damaged when you are
installing/replacing the memory module. In this instance you should
avoid mats that are made of materials that hold or generate static
electricity.

■ When installing or removing a memory module, you must ensure that

you do not touch any other internal areas of the computer.

■ Insert the two memory modules into Slot A and Slot B respectively. The

computer will operate in dual channel mode.
You can access the inserted memory modules efficiently in dual
channel.

■ Use only memory modules approved by TOSHIBA.

■ Do not try to install or remove a memory module under the following

conditions.
a. The computer is turned on.
b. The computer was shut down in either Sleep or Hibernation Mode.
c. Wake-up on LAN is enabled.
d. The wireless communication switch is turned on.

■ Be careful not to let screws or other foreign matter fall into the

computer. It could cause malfunction or electric shock.

■ Additional memory module is a precision electronic component that

may be fatally damaged by static electricity. Since the human body can
carry static electricity, it is important that you discharge yourself before
touching or installing any additional memory modules. To discharge
your body’s static electricity, simply touch any metal close to you with
bare hands.

User’s Manual 3-22

Hardware, Utilities and Options

Installing a memory module

To install a memory module, follow the steps as detailed below:

1. Shut down the computer - make sure the Power indicator is off (refer to
the Turning off the power section in Chapter 1, Getting Started if
required).

2. Remove the AC adaptor and all cables and peripherals connected to
the computer.

3. Close the display panel.

4. Turn the computer upside down and remove the battery pack (refer to

Replacing the battery pack section in Chapter 6, Power and Power-Up

Modes, if required).

5. Loosen the screw securing the memory module cover in place - please
note that this screw is attached to the cover in order to prevent it from
being lost.

Use a point size 0 Phillips screwdriver.

6. Slide your fingernail or a thin object under the cover and lift it off.

1

2

1. Memory module cover

Figure 3-8 Removing the memory module cover

User’s Manual 3-23

2. Screw

Hardware, Utilities and Options

7. Align the notch of the memory module with that of the memory slot and
gently insert the module into the slot at about a 30 degree angle before
holding it down until the latches on either side snap into place.

1

3

2

1. Notch

2. Slot A

Figure 3-9 Seating the memory module

3. Slot B

■ Never allow metal objects, such as screws, staples and paper clips, to

enter the computer. Foreign metal objects can create a short circuit,
which can cause computer damage and fire, possibly resulting in
serious injury.

■ Do not touch the connectors on the memory module or on the

computer. Debris on the connectors may cause memory access
problems.

■ The slot A is reserved for the first memory module. Use the slot B for

expanded memory. If only one module is installed, use the slot A.

■ Align the grooves along the edges of the memory module with the

locking tabs on the connector and insert the module into the connector
firmly - if you find it difficult to install the memory module, gently prise
the locking tabs outwards using the tip of your finger.

Please also ensure that you hold the memory module along its left and
right hand edges - the edges with the grooves in.

8. Seat the memory module cover in place and secure it with the screw.

Take care to ensure that the memory module cover is firmly closed.

User’s Manual 3-24

Hardware, Utilities and Options

1

2

1. Memory module cover

Figure 3-10 Seating the memory module cover

2. Screw

9. Install the battery pack - refer to Replacing the battery pack section in
Chapter 6, Power and Power-Up Modes, if required.

10. Turn your computer over.

11. Turn the computer on and make sure the added memory is recognized ­to confirmed it, Start -> Control Panel -> System and Security ->
System icon.

Removing a memory module

To remove the memory module, follow the steps as detailed below:

1. Shut down the computer - make sure the Power indicator is off (refer to
the Turning off the power section in Chapter 1, Getting Started if
required).

2. Remove the AC adaptor and all cables and peripherals connected to
the computer.

3. Close the display panel.

4. Turn the computer upside down and remove the battery pack (refer to

Replacing the battery pack section in Chapter 6, Power and Power-Up

Modes, if required).

5. Loosen the screw securing the memory module cover in place - please
note that this screw is attached to the cover in order to prevent it from
being lost.

6. Slide your fingernail or a thin object under the cover and lift it off.

7. Push the latches away from the module in order to release it - a spring
will force one end of the module up at an angle.

User’s Manual 3-25

Hardware, Utilities and Options

8. Grasp the module by its edges and remove it from the computer.

■ If you use the computer for a long time, the memory modules and the

circuits locating close to the memory modules will become hot. In this
case, let them cool to room temperature before you replace them. Or
you will get burnt if you touch any of them.

■ Do not touch the connectors on the memory module or on the

computer. Debris on the connectors may cause memory access
problems.

1

1. Latches

Figure 3-11 Removing the memory module

9. Seat the memory module cover in place and secure it with the screw.

Take care to ensure that the memory module cover is firmly closed.

10. Install the battery pack - refer to Replacing the battery pack section in
Chapter 6, Power and Power-Up Modes, if required.

11. Turn your computer over.

External monitor

An external analog monitor can be connected to the external monitor port
on the computer. To connect a monitor, follow the steps as detailed below:

Connecting the monitor cable

1. Connect the monitor cable to the external monitor port and tighten the
screws on the left and right hand side of the connector as required.

User’s Manual 3-26

Hardware, Utilities and Options

1

2

1. External monitor port

Figure 3-12 Connecting the monitor cable to the external monitor port

2. Monitor cable

2. Turn the external monitor's power on.

When you turn on the power, the computer will automatically recognize the
monitor and determine whether it is a color or monochrome device. In the
event that you find that there are issues getting an image displayed on the
correct monitor, you should consider using the FN + F5 hot key to change
the display settings (if you then disconnect the external monitor before you
turn the computer's power off, be sure to press FN + F5 hot key again to
switch to the internal display).

Please refer to Chapter 5, The Keyboard, for further details on using hot
keys to change the display setting.

Do not disconnect the external monitor while in Sleep or Hibernation Mode.
Turn off the computer before disconnecting the external monitor.

When displaying desktop at external analog monitor, desktop is sometimes
displayed on the center of the monitor with black bars around desktop (with
small size).

At that time, please read the manual of the monitor and set the display
mode which is supporting at the monitor. Then it will be displayed with
suitable size with correct aspect ratio.

Mini DisplayPort

With a suitable adapter (such as the "Mini DisplayPort to HDMI adapter" or
"Mini DisplayPort to DVI adapter"), this port enables you to connect an
external monitor.

User’s Manual 3-27

Hardware, Utilities and Options

Connecting the Mini DisplayPort

1. Plug the Mini DisplayPort connector of the adapter into the Mini
DisplayPort on your computer.

1

2

1. Mini DisplayPort

Figure 3-13 Connecting the Mini DisplayPort

2. Mini DisplayPort Connector

2. Connect one end of the monitor cable to the HDMI or DVI port on your
external monitor and connect the other end to the suitable port of the
adapter.

■ "Mini DisplayPort to HDMI adapter" or "Mini DisplayPort to DVI

adapter" is not supplied with your computer. This product may be
purchased from the retailer.

■ As the port operation has not been confirmed, some monitors may not

function properly.

eSATA (External Serial ATA)

A device corresponding to eSATA function can be connected to the
eSATA/USB combo port on the computer.

Connecting the eSATA device

To connect an eSATA device, follow the steps as detailed below:

1. Connect an eSATA cable to the eSATA/USB combo port.

Make sure the connector is properly aligned with the socket.
Do not try to force the connection, doing so can damage the connecting

pins.

User’s Manual 3-28

Hardware, Utilities and Options

2

1

1. eSATA cable 2. eSATA/USB combo port

Figure 3-14 Connecting an eSATA cable to the eSATA/USB combo port

■ A connected eSATA device may not be recognized if it is connected to

the computer's eSATA/USB combo port while the computer is in Sleep
Mode or Hibernation Mode. If this occurs, disconnect the eSATA device
and then reconnect the device while the computer is turned on.

■ If you connect an eSATA device after the computer has already been

turned on, it will take about ten seconds for it to be recognized by the
computer.
Do not attempt to disconnect and reconnect the drive before this period
has elapsed.

Disconnecting an eSATA device

When you have finished using an eSATA device, you can follow the
procedures below in order to disconnect it:

1. Wait for the indicator light of an eSATA device to go out to make sure all
activity has stopped.

If you disconnect an eSATA device or turn off the power while the
computer is accessing the drive you may lose data or damage an eSATA
device or the drive.

2. Click the Safely Remove Hardware icon on the Windows Taskbar.

3. Click an eSATA device that you want to remove.

4. Carefully pull an eSATA device's eSATA/USB combo connector out
from within the computer's eSATA/USB combo port.

Serial port

The serial connector can be used to connect to RS-232C compatible
devices.

RS-232C compatible devices include the following:

■ Modem

■ Mouse

■ Printer

User’s Manual 3-29

Hardware, Utilities and Options

Some models are equipped with a serial port.
To connect a serial port, follow the steps as detailed below:

1. Turn the computer’s power off.

2. Connect the serial connector to the serial port and tighten the screws on
the left and right hand side.

1. Serial connector 2. Serial port

Figure 3-15 Connecting the serial connector to the serial port

Security lock

A security locks enable you to anchor your computer a desk or other heavy
object in order to help prevent unauthorized removal or theft. The computer
has a security lock slot on its back side into which you can attach one end
of the security cable, while the other end attaches to a desk or similar
object. The methods used for attaching security cables differ from product
to product. Please refer to the instructions for the product you are using for
more information.

2

1

Connecting the security lock

In order to connect a security cable to the computer, follow the steps as
detailed below:

1. Turn the computer so its back side faces you.

2. Align the security cable with the lock slot and secure it in place.

User’s Manual 3-30

1

1. Security lock slot

Optional accessories

You are able to add a number of options and accessories in order to make
your computer even more powerful and convenient to use. For reference,
the following list details some of the items that are available from your
reseller or TOSHIBA dealer:

Hardware, Utilities and Options

Figure 3-16 Security lock

DDR3-1333 Memory
Kit

Universal AC
Adaptor

A 1 GB, 2 GB or 4 GB memory module (DDR3-

1333) can easily be installed in the computer.

If you frequently use your computer at more than
one site, it may be convenient to purchase an
additional AC adaptor to be kept at each site in
order to remove the need to always carry the
adaptor with you.

Battery Pack An additional battery pack can be purchased for

use as either a spare or replacement. Please
refer to Chapter 6, Power and Power-Up Modes
for further information.

User’s Manual 3-31

Operating Basics

This chapter describes the basic operations of your computer, highlights
the precautions that should be taken when using it.

Using the Touch Pad

To use the Touch Pad, simply touch and move your fingertip across it in the
direction you want the on-screen pointer to go.

Chapter 4

1

2

3

1. Touch Pad 3. Touch Pad control buttons

2. Fingerprint Sensor*

* Provided with some models.

Figure 4-1 Touch Pad and Touch Pad control buttons

The two buttons below the Touch Pad are used like the buttons on a
standard mouse - press the left button to select a menu item or to
manipulate text or graphics designated by the pointer, and press the right
button to display a menu or other function depending on the software you
are using.

User’s Manual 4-1

You can also tap the Touch Pad to perform functions similar to those of the
left button on a standard mouse.

Click: Tap once
Double-click: Tap twice
Drag and drop: Tap to select the item(s) you want to move, leave your

finger on the Touch Pad after the second tap and then move the item(s)
to their new destination.

Using the Fingerprint Sensor

This product has a fingerprint utility installed for the purpose of enrolling
and recognizing fingerprints. By enrolling the ID and password onto the
fingerprint authentication feature, it is no longer necessary to input the
password from the keyboard. Fingerprint feature enables you to:

■ Logon to Windows and access a security enabled homepage through

Internet Explorer.

■ Files and folders can be encrypted/decrypted and third party access to

them prevented.

■ Unlock the password-protected screen-saver.

■ Authentication of the User Password (and, if applicable, the HDD (Hard

Disk Drive) Password) when booting up the computer (boot
authentication).

■ Single Sign-On feature

Operating Basics

Fingerprint cannot be used in models that do not have a fingerprint module
installed.

How to Swipe your Finger

Using the following steps when swiping fingers for fingerprint registration or
authentication will help to minimize authentication failures:

Align the first joint of the finger to the center of the sensor. Lightly touch the
sensor and swipe finger levelly towards you until the sensor surface
becomes visible. In performing this process, you should also take care to
ensure that the center of your fingerprint is on the sensor.

User’s Manual 4-2

Operating Basics

The following illustrations show the recommended way to swipe your finger
over the fingerprint sensor.

1

1

1. Sensor

Figure 4-2 Swipe the finger

■ Avoid swiping with your finger stiff or pressed too hard onto the sensor,

and take care to ensure that the center of the fingerprint is touching the
sensor before swiping. Either of these conditions may cause fingerprint
reading to fail.

■ Check the center of the fingerprint whorl before swiping and then

ensure this is swiped along the center line of the sensor.

■ There is a possibility of authentication failures if the finger is swiped too

quickly or too slowly - follow any on-screen instructions to adjust the
speed used during the swipe process.

Points to note about the Fingerprint Sensor

Please be aware of the following considerations when using the fingerprint
sensor. A failure to follow these guidelines might result in damage to the
sensor, sensor failure, fingerprint recognition problems or a lower
fingerprint recognition success rate.

■ Do not scratch or poke the sensor with your nails or any hard or sharp

objects.

■ Do not press the sensor strongly.

■ Do not touch the sensor with a wet finger or any wet objects - keep the

sensor surface dry and free from water vapor.

■ Do not touch the sensor with a soiled or dirty finger as minute foreign

particles of dust and dirt may scratch it.

■ Do not paste stickers or write on the sensor.

■ Do not touch the sensor with a finger or any other object which may

have a build-up of static electricity on it.

User’s Manual 4-3

Operating Basics

Observe the following before you place your finger on the sensor whether
for fingerprint enrollment/registration or recognition.

■ Wash and dry your hands thoroughly.

■ Remove static electricity from your fingers by touching any metal

surface. Static electricity is a common cause of sensor failures,
especially when the weather is dry.

■ Clean the sensor with a lint-free cloth - do not use detergent or any

other chemicals to clean the sensor.

■ Avoid the following finger conditions for enrollment or recognition as

they may result in fingerprint enrollment errors or a drop in the
fingerprint recognition success rate

■ Soaked or swollen finger, for example as may occur after taking a

bath.

■ Injured finger

■ Wet finger

■ Soiled or oily finger

■ Extremely dry skin condition on finger

Observe the following to improve the fingerprint recognition success rate.

■ Enroll two or more fingers.

■ Enroll additional fingers if a recognition failure often occurs when using

already enrolled fingers.

■ Check the condition of your finger - any conditions which have changed

since enrollment, such as injury, rough skin, and extremely dry, wet,
soiled, dirty, oily, soaked or swollen fingers, may lower the recognition
success rate. Also if the fingerprint is worn down or the finger becomes
thinner or fatter, the recognition success rate may be lowered.

■ As the fingerprint for each finger is different and unique you should

ensure that only the registered or enrolled fingerprint or fingerprints are
used for identification.

■ Check the position and speed at which you swipe your finger across the

sensor - please refer to the preceding drawing.

■ The fingerprint sensor compares and analyzes the unique

characteristics in a fingerprint. However, there may be instances where
certain users are unable to register their fingerprints due to insufficient
unique characteristics in their fingerprints.

■ The recognition success rate may differ from user to user.

Points to note about Fingerprint Utility

■ If Windows 7 file encryption function EFS (Encryption File System) is

used to encrypt a file, the file cannot be further encrypted using the
encryption function of this software.

■ You can back up the fingerprint data or the information registered to

Automatic password input in IE.

■ Please use Import/Export on TOSHIBA Fingerprint Utility main menu.

User’s Manual 4-4

■ Please also refer to the fingerprint utility Help file for more information.

You can start it using the following method:

■ Click Start -> All Programs -> TOSHIBA -> Utilities -> Fingerprint

Utility. The main screen is displayed. Click ? in the lower left corner

of the screen.

Fingerprint utility limitations

TOSHIBA does not guarantee that the fingerprint utility technology will be
completely secure or error-free, or that it will accurately screen out
unauthorized users at all times. TOSHIBA is not liable for any failure or
damage that might arise out of the use of the fingerprint software.

■ The fingerprint sensor compares and analyzes the unique

characteristics in a fingerprint. However, there may be instances where
certain users are unable to register their fingerprints due to insufficient
unique characteristics in their fingerprints.

■ The recognition success rate may differ from user to user.

Setup Fingerprint Registration

Please use the following procedure when first using fingerprint
authentication.

■ In use, the fingerprint authentication system will use the same

username and password as defined within the Windows operating
system. If no Windows password has been configured, you must do
this before starting the fingerprint registration process.

■ This sensor has the memory space for at least twenty fingerprint

patterns. You might be able to register more fingerprint patterns
depending on the sensor memory usage.

Operating Basics

1. Click Start -> All Programs -> TOSHIBA -> Utilities -> Fingerprint
Utility, or click the Fingerprint utility icon in the Notifications Area.

2. The Enroll screen is displayed. Enter the current account password
into the Windows Password field. If no Windows password has been
configured, you will be asked to configure the new logon password.
Then click Next.

3. Click the non-enrolled finger icon above the finger you want to register
and then click Next.

4. The note for enrollment operation screen is displayed. Confirm the
message and then click Next.

5. The scanning practice screen is displayed. You are able to practice
swiping (three times) your finger to ensure you use the correct method.
When you have finished practicing swiping your finger, click Next. You
can also click Skip to skip scanning practice.

6. Swipe three times with the same finger. If scanning of fingerprint
succeeds, "Enrollment succeed. Do you want to save this
fingerprint?" message box will appear. Click OK.

User’s Manual 4-5

7. The following message will be displayed: "It is strongly
recommended you enroll one more finger." Click OK and
repeat Step 3, 4, 5 and 6 with another finger.

■ It is strongly recommended that you register 2 or more fingerprints.

Delete the Fingerprint Data

Saved fingerprint data is stored in special non-volatile memory inside the
fingerprint sensor. Therefore, if you give the computer to someone else, or
dispose of it in any way, the following process is recommended to delete
your fingerprint information:

Delete the fingerprint data for the currently logged in user

1. Click Start -> All Programs -> TOSHIBA -> Utilities -> Fingerprint
Utility, or double click the utility icon in the Notifications Area.

2. Swipe your finger across the fingerprint sensor.

3. The TOSHIBA Fingerprint Utility main menu is displayed. Select
Enroll in the main menu.

4. In the Enroll window, it enables you to delete the fingerprint data for the
currently logged in user. Click an enrolled finger you want to delete.

"Are you sure you want to delete this template?"

message box will appear on the screen and then click OK button.
If you want to delete other fingerprints, repeat this step.
If only one fingerprint is registered, the message "Sorry! At least
one fingerprint is required" will appear after clicking OK. You
are not allowed to delete a unique fingerprint.

5. Click Close.

6. "Are you sure you want to quit?" is displayed. Click OK. It will
be returned to the TOSHIBA Fingerprint Utility main menu.

Operating Basics

Delete all users fingerprints

1. In the TOSHIBA Fingerprint Utility main menu, click Run as
administrator in the lower left.

2. User Account Control window is displayed. Click Yes.

3. Swipe your enrolled finger.

4. Select Fingerprint Control option.

5. A list of fingerprint information for all users is shown in the screen. Click
Delete All in the lower right.

6. "Are you sure you want to delete all fingerprints?"
message box will appear on the screen. Click OK.

7. Click Close.

8. "Are you sure you want to quit?" is displayed. Click OK. It will
be returned to the TOSHIBA Fingerprint Utility main menu.

User’s Manual 4-6

Operating Basics

Windows Logon via Fingerprint Authentication

In place of the usual Windows logon by ID and password, fingerprint
authentication also allows logon to Windows.

This is useful especially when many users are using the PCs, as user
selection can be skipped.

Fingerprint Authentication Procedure

1. Start up the computer.

2. The Logon Authorization screen is displayed. Choose any of the
enrolled fingers and swipe the fingerprint on the sensor. If
authentication is successful, the user will be logged on to Windows.

■ If the fingerprint authentication fails, please logon using the Windows

logon password.

■ Please logon using the Windows logon password if the fingerprint

authentication failed. To logon using the Windows logon password,
enter the Windows logon password at the [Welcome] screen as normal.

■ A warning message will be displayed when authentication is abnormal

or authentication is not successful within a fixed duration.

Fingerprint boot authentication and Single Sign-on feature

Overview about Fingerprint boot authentication

The fingerprint authentication system can be used to replace the keyboard
based User Password authentication system when booting up.

If you do not want to use the fingerprint authentication system for password
authentication when booting up, but prefer to use the keyboard-based
system instead, click the user’s tile when the Fingerprint System
Authentication screen is displayed. This will switch the password input
screen across to the keyboard-based one.

■ You must ensure that you use the TOSHIBA Password Utility to

register a User Password before using the Fingerprint boot
authentication and its extended function to allow fingerprints to be used
to access the computer when it is turned on.

■ If the fingerprint authentication process fails five times, a preset time

limit is exceeded, or you press the BACK SPACE key, [Password =]
will be displayed on the screen and you will have to enter either the
User Password or Supervisor Password manually in order to start the
computer.

■ When swiping your finger, please ensure that you do it slowly and at a

constant speed. If you find that this does not improve the authentication
rate, you should try to adjust the speed at which the finger is swiped.

■ If there are any changes in the environment or settings related to

authorization, you will be required to provide authorization information
such as a User Password (and, if applicable, the HDD(Hard Disk Drive)
password).

User’s Manual 4-7

Operating Basics

Overview about Fingerprint Single Sign-on feature

This is a feature that allows the user to complete the authentication for both
the User/BIOS Password (and, if applicable, the HDD (Hard Disk Drive)
Password) and logging onto Windows using only one fingerprint
authentication when booting up.

It is necessary to register the User/BIOS Password and Windows Logon
Password before using the Fingerprint boot authentication and this
Fingerprint Single Sign-On Feature. Please use the TOSHIBA Password
Utility to register your User/BIOS Password. If Windows Logon is not the
default for your system, see Manual to register your Windows Logon
Password.

Only one fingerprint authentication is required to replace the User/BIOS
Password (and, if applicable, the HDD (Hard Disk Drive) Password) and
the Windows Logon Password.

How to Enable Fingerprint boot authentication and Single
Sign-On feature

It is necessary to first enroll your fingerprint with the TOSHIBA Fingerprint
Utility prior to enabling and configuring the boot authentication and Single
Sign-On feature. You should check that your fingerprint is enrolled before
configuring the settings.

1. Logon as Administrator (means a user has administrator privileges).

2. Click Start -> All Programs -> TOSIHBA -> Utilities -> Fingerprint
Utility.

3. Swipe your finger across the fingerprint sensor.

4. The TOSHIBA Fingerprint Utility main menu is displayed. Click Run
As Administrator in lower left.

5. User Account Control window is displayed. Click Yes.

6. Swipe your finger across the fingerprint sensor.

7. Select Setting in the main menu to open the Setting window, you can

■ Select Boot authentication check box if you want to use the

fingerprint boot authentication feature.

■ Select Boot authentication and Single sign-on check boxes if you

want to use the Single Sign-on feature.

8. Click Apply.

9. "Save succeeded" is displayed. Click OK.

10. Click Close.

11. "Are you sure you want to quit?" is displayed. Click OK. It will
be returned to the TOSHIBA Fingerprint Utility main menu.

This modified configuration for fingerprint boot authentication and Single
Sign-on feature becomes effective the next time the system is booted up.

User’s Manual 4-8

Web Camera

Web Camera is a device that allows you to record video or take

photographs with your computer. You can use it for video chatting or video
conferences using a communication tool such as Windows Live
Messenger. TOSHIBA Web Camera Application will help you to add
various video effects to your video or photograph.

Enables the transmission of video and use of video chat via the internet
using specialized applications.

Some models are equipped with a Web Camera.
Please refer to the Web Camera Application Online Help for details.

Operating Basics

1

2

1. Web Camera 2. Web Camera LED

Figure 4-3 Web Camera

■ Do not point the web camera directly at the sun.

■ Do not touch or press strongly on the web camera lens. Doing so may

reduce image quality. Use an eyeglass cleaner (cleaner cloth) or other
soft cloth to clean the lens if it becomes dirty.

■ Setting the [Size] to more than "800x600" will cause a larger amount of

data to be written to the hard disk drive and may interfere with smooth
recording.

■ When recording in dimly lit environments, select "Night Mode" which

allows for brighter images with less noise.

User’s Manual 4-9

Using the TOSHIBA Face Recognition

TOSHIBA Face Recognition uses a face verification library to verify the
face data of users when they log in to Windows. The user can thus avoid
having to enter a password or the like, which makes the login process
easier.

■ TOSHIBA Face Recognition does not guarantee the correct

identification of a user. Changes to the likeness of a registrant, such as
hair style changes, wearing a cap, or wearing glasses may effect the
recognition rates when such changes occur after the registrant had
registered.

■ TOSHIBA Face Recognition may incorrectly recognize faces that are

similar to a registrant.

■ For high security purposes, TOSHIBA Face Recognition is not a

suitable substitute for Windows passwords. When security is a high
priority, use your established Windows passwords to log in.

■ Bright background light and/or shadows may prevent a registrant from

being recognized correctly. In that case, log in using your Windows
password. If recognition of a registrant fails repeatedly, refer to your
computer documentation to learn ways to improve recognition
performance.

■ TOSHIBA Face Recognition records face data in a log when face

recognition fails. When transferring ownership or disposing of your
computer, please uninstall the application or delete all the logs created
by the application. For details on how to do this, see help file.

■ TOSHIBA Face Recognition can be used only in Windows 7.

Operating Basics

Disclaimer

Toshiba does not guarantee that the face recognition utility technology will
be completely secure or error-free. Toshiba does not guarantee that the
face recognition utility will accurately screen out unauthorized users at all
times. Toshiba is not liable for any failure or damage that might arise out of
the use of the face recognition software or utility.

TOSHIBA, ITS AFFILIATES AND SUPPLIERS SHALL HAVE NO
RESPONSIBILITY FOR DAMAGE TO OR LOSS OF ANY BUSINESS,
PROFITS, PROGRAMS, DATA, NETWORK SYSTEMS OR REMOVABLE
STORAGE MEDIA ARISING OUT OF OR RESULTING FROM THE USE
OF THE PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY
THEREOF.

How to register the Face Recognition Data

Take a picture for facial verification purposes, and register the data needed
when you log in. To register the data needed when you log in, follow the
steps as described below:

1. To launch this utility, click Start -> All Programs -> TOSHIBA ->
Utilities -> Face Recognition.

User’s Manual 4-10

Operating Basics

■ The Registration screen is displayed for a logged-in user whose

face has not been registered.

■ The Management screen is displayed for a logged-in user whose

face has already been registered.

2. Click Run as administrator in lower left of the Management screen,
and then click the Register button. The Registration screen is
displayed.

■ If you wish to practice, click on the Next button in the Registration

screen.

■ If you do not wish to practice, click on the Skip button in the

Registration screen.

3. Click the Next button to start the guide. Please follow the guide to
practice.

■ Click the Back button to practice the guide once more.

4. Click the Next button to start image-capturing process.
Adjust the position of your face so that it fits within the face-shaped
frame.

5. Once your face has been positioned properly, the recording will
commence.
Start moving your neck very slightly to the left and right, and then move
your neck down and up.

6. Registration will end after you have repeatedly moved your neck left,
right, down and up.
When the register succeeds, below message will be displayed on the
screen:
"Registration successful. Now we’ll do the
verification test. Click the Next button."
Click the Next button to perform the verification test.

7. Perform the verification test. Face the screen as you do when you
register.

■ If verification fails, click the Back button and re-register. Please refer

to step 6 from step 4.

8. If verification is successful, click the Next button and register an
account.

9. Register the account.
Fill in all the fields.

10. The Management screen is displayed.
The registered account name will be displayed. Clicking on it will cause
the captured image of your face to be displayed on the left.

User’s Manual 4-11

How to Delete the Face Recognition Data

Delete image data, account information, and personal record data created
during registration. To delete the Face Recognition Data, follow the steps
as described below:

1. To launch this utility, click Start -> All Programs -> TOSHIBA ->
Utilities -> Face Recognition.
The Management screen is displayed.

2. Select a user which is displayed in the Management screen.

3. Click the Delete button. "You are about to delete the user
data. Would you like to continue?" will be displayed on the
screen.

■ If you do not want the data to be deleted, click the No button and

you will then be returned to the Management screen.

■ Clicking on the Yes button will remove the selected user from the

Management screen.

How to launch the help file

For further information on this utility, please refer to help file.

1. To launch the help file, click the Help button in the Management
screen.

Windows Logon via TOSHIBA Face Recognition

This section explains how to login to Windows with TOSHIBA Face
Recognition. Two authentication modes are provided.

■ 1:N Mode Login screen: If the face authentication tile is selected by

default, you can log in without using the keyboard or mouse.

■ 1:1 Mode Login screen: This mode is essentially the same as AUTO

mode, but the Select Account screen will appear before the Display
Captured Image screen, and you will need to select the user account
to be authenticated in order to start the authentication process.

Operating Basics

1:N Mode Login screen

1. Turn on the computer.

2. The Select Tiles screen will be displayed.

3. Select Start face recognition ().

4. "Please face the camera" will be displayed.

5. Verification will be performed. If the authentication is successful, the
image data taken in step 4 will be faded in and placed over one another.

■ If an error occurs during authentication, you will be returned to the

Select Tiles screen.

6. The Windows Welcome screen will be displayed, and will be logged in
automatically to Windows.

User’s Manual 4-12