Toshiba S1ES Schematic

SCHEMATIC DIAGRAM MODEL : 29A3DE / 29A3E / 29A3SH

WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "X-RAY RADIATION PRECAUTION", "SAFETY
PRECAUTION" AND "PRODUCT SAFETY NOTICE" ON THE MANUAL FOR THIS MODEL.

CAUTION: The international hazard symbols "*" in the schematic diagram and the parts list designate components
which have special characteristics important for safety and should be replaced only with types identical to those in the
original circuit or specified in the parts list. The mounting position of replacements is to be identical with originals.
Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE on the MANUAL for this
model. Do not degrade the safety of the receiver through improper servicing.

NOTE:

1. RESISTOR Resistance is shown in ohm [K = 1.000, M = 1.000.000]. All resistors are 1/6W and 5%
tolerance carbon resistor, unless otherwise noted as the following marks.
1/2R = Metal or Metal oxide of 1/2 watt 1/2S = Carbon compsistion of 1/2 watt
1RF = Fuse resistor of 1 watt 10W = Cement of 10 watt
K = ±10% G = ±2% F = ±1%

2. CAPACITOR Unless otherwise noted in schematic, all capacitor values less than 1 are expressed in
?F, and the values more than 1 in pF.
All capacitors are ceramic 50V, unless otherwise noted as the following marks.

Electolytic capacitor Mylar capacitor

3. The parts indicated with " * " have special characteristics, and should be replaced with identical parts only.

4. Voltages read with DIGITAL MULTI-METER from point indicated to chassing ground, using a color bar signal with all
controls at normal, line voltage 220 volts.

5. Waveforms are taken receiving color bar signal with enough sensitivity.

6. Voltage reading shown are nominal values and may vary ±20% except H.V.

ound, using a color bar signal with all

DEL : 29A3DE / 29A3E / 29A3SH

un

M = 1.000.000]. All resistors are 1/6W and 5%

ise noted as the following marks.

1/2S = Carbon compsistion of 1/2 watt
10W = Cement of 10 watt

l capacitor values less than 1 are expressed in

therwise noted as the following marks.

Mylar capacitor

tics, and should be replaced with identical parts only.

4. Voltages read with DIGITAL MULTI-METER from point indicated to chassing gro
controls at normal, line voltage 220 volts.

5. Waveforms are taken receiving color bar signal with enough sensitivity.

6. Voltage reading shown are nominal values and may vary ±20% except H.V.

SCHEMATIC DIAGRAM MO

D

=

se

ca

he

ics

CHASSIS, READ THE "X-RAY RADIATION PRECAUTION", "SAFETY
TY NOTICE" ON THE MANUAL FOR THIS MODEL.

bols "*" in the schematic diagram and the parts list designate components

tant for safety and should be replaced only with types identical to those in the

t. The mounting position of replacements is to be identical with originals.
ts, read carefully the PRODUCT SAFETY NOTICE on the MANUAL for this

receiver through improper servicing.

NOTE:

1. RESISTOR Resistance is shown in ohm [K = 1.000, M
tolerance carbon resistor, unless otherwi
1/2R = Metal or Metal oxide of 1/2 watt
1RF = Fuse resistor of 1 watt
K = ±10% G = ±2% F = ±1%

2. CAPACITOR Unless otherwise noted in schematic, all
?F, and the values more than 1 in pF.
All capacitors are ceramic 50V, unless ot

Electolytic capacitor

3. The parts indicated with " * " have special characterist