Toshiba S100 User Manual

PORTÉGÉ S100

TOSHIBA

PORTÉGÉ S100

Portable Personal Computer

User’s Manual

User’s Manual

Copyright

© 2005 by TOSHIBA Corporation. All rights reserved. Under the copyright
laws, this manual cannot be reproduced in any form without the prior
written permission of TOSHIBA. No patent liability is assumed, with respect
to the use of the information contained herein.

TOSHIBA PORTÉGÉ S100 Portable Personal Computer User’s Manual

First edition May 2005
Copyright authority for music, movies, computer programs, data bases and

other intellectual property covered by copyright laws belongs to the author
or to the copyright owner. Copyrighted material can be reproduced only for
personal use or use within the home. Any other use beyond that stipulated
above (including conversion to digital format, alteration, transfer of copied
material and distribution on a network) without the permission of the
copyright owner is a violation of copyright or author’s rights and is subject
to civil damages or criminal action. Please comply with copyright laws in
making any reproduction from this manual.

Disclaimer

This manual has been validated and reviewed for accuracy. The
instructions and descriptions it contains are accurate for the TOSHIBA
PORTÉGÉ S100 Portable Personal Computer at the time of this manual’s
production. However, succeeding computers and manuals are subject to
change without notice. TOSHIBA assumes no liability for damages incurred
directly or indirectly from errors, omissions or discrepancies between the
computer and the manual. Graphics processor performance may vary
considerably from specifications due to design configuration.

Trademarks

IBM is a registered trademark and IBM PC is a trademark of International
Business Machines Corporation.

Intel, Intel SpeedStep, Pentium and Centrino are trademarks or registered
trademarks of Intel Corporation.

Windows and Microsoft are registered trademarks of Microsoft Corporation.
Photo CD is a trademark of Eastman Kodak.
Sonic and RecordNow! are registered trademark of Sonic Solutions.
i.LINK is a trademark of Sony Corporation.
InterVideo and WinDVD are registered trademarks of InterVideo Inc.

WinDVD Creator is trademark of InterVideo Inc.
Other trademarks and registered trademarks not listed above may be used

in this manual.

ii User’s Manual

EU Declaration of Conformity

This product is carrying the CE-Mark in accordance with the related
European Directives. Responsible for CE-Marking is TOSHIBA Europe
GmbH, Hammfelddamm 8, 41460 Neuss, Germany.

The complete and official EU Declaration of Conformity can be found on
TOSHIBA’s web site http://epps.toshiba-te

Modem warning notice

Conformity Statement

The equipment has been approved to [Commission Decision “CTR21”] for
pan-European single terminal connection to the Public Switched Telephone
Network (PSTN).

However, due to differences between the individual PSTNs provided in
different countries/regions the approval does not, of itself, give an
unconditional assurance of successful operation on every PSTN network
termination point.

In the event of problems, you should contact your equipment supplier in the
first instance.

Network Compatibility Statement

This product is designed to work with, and is compatible with the following
networks. It has been tested to and found to conform with the additional
requirements conditional in EG 201 121.

Germany ATAAB AN005,AN006,AN007,AN009,AN010

and DE03,04,05,08,09,12,14,17
Greece ATAAB AN005,AN006 and GR01,02,03,04
Portugal ATAAB AN001,005,006,007,011 and

P03,04,08,10
Spain ATAAB AN005,007,012, and ES01
Switzerland ATAAB AN002
All other countries/regions ATAAB AN003,004
Specific switch settings or software setup are required for each network,

please refer to the relevant sections of the user guide for more details.
The hookflash (timed break register recall) function is subject to separate

national type approvals. It has not been tested for conformity to national
type regulations, and no guarantee of successful operation of that specific
function on specific national networks can be given.

User’s Manual

g.com on the Internet.

User’s Manual iii

User’s Manual

Description on Laser specification

The optical drive such as DVD-ROM&CD-R/RW drive and DVD Super Multi
drive that is used in this computer is equipped with laser. The classification
label with the following sentence is affixed to the surface of the drive.

CLASS 1 LASER PRODUCT
LASER KLASSE 1
LUOKAN 1 LASERLAITE
APPAREIL A LASER DE CLASSE 1
KLASS 1 LASER APPARAT

The drive with the above label is certified by the manufacturer that the drive
complies with the requirement for laser product on the date of
manufacturing pursuant to article 21 of Code of Federal Regulations by the
United States of America, Department of Health & Human Services,
Food and Drug Administration.

In other countries, the drive is certified to comply with the requirement
pursuant to IEC 825 and EN60825 on class 1 laser product.

This computer is equipped with the optical drive in the following list
according to the model purchased.

Manufacturer Type

MATSUSHITA UJDA765

MATSUSHITA UJ-822

iv User’s Manual

PORTÉGÉ S100

Table of Contents

General Precautions

Preface

Manual contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii

Conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiv

Chapter 1 : Introduction

Equipment checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

Special features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9

Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12

Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16

Chapter 2 : The Grand Tour

Front with the display closed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Left side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Right side. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Back side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Underside. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

Front with the display open . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

System indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

Keyboard indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10

USB floppy disk drive (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11

Optical media drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12

AC adaptor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14

Chapter 3 : Getting Started

Setting up your work space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Connecting the AC adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

Opening the display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

Turning on the power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7

Starting up for the first time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7

Turning off the power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8

Restarting the computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11

Restoring the preinstalled software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12

User’s Manual v

Table of Contents

Chapter 4 :

Operating Basics

Using the Touch Pad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1

Using the USB floppy disk drive (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2

Changing Ultra Slim Bay modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3

Using optical media drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5

Writing CDs on DVD-ROM&CD-R/RW drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-8

Writing CD/DVDs on DVD Super Multi drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-10

Media care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-18

Sound System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-19

Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-21

Wireless communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-23

LAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-25

Cleaning the computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-27

Moving the computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-27

Using the Hard Disk Drive (HDD) Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-28

Heat dispersal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-31

Chapter 5 : The Keyboard

Typewriter keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1

Function keys: F1 … F12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2

Soft keys: Fn key combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2

Hot keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-3

Windows special keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-7

Keypad overlay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-7

Generating ASCII characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-9

Chapter 6 : Power and Power-Up Modes

Power conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1

Power indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2

Battery types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-3

Care and use of the battery pack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-5

Replacing the battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-11

TOSHIBA Password Utility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-14

Power-up modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-16

Panel power on/off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-17

System Auto Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-17

Chapter 7 : HW Setup

Accessing HW Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1

HW Setup window. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1

Configuring the Execute-Disable Bit Capability and TPM. . . . . . . . . . . . . . . . . . . . .7-8

vi User’s Manual

Table of Contents

Chapter 8 :

Optional Devices

PC card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2

SD card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3

Memory expansion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5

Battery pack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9

AC adaptor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9

Battery charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10

Hard disk drive pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10

Ultra Slim Bay HDD adaptor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12

USB floppy disk drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-13

External monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-13

i.LINK (IEEE1394) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-14

Advanced Port Replicator IIl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-16

Parallel printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-17

Security lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-18

Chapter 9 : Troubleshooting

Problem solving process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1

Hardware and system checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3

TOSHIBA support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-19

Appendix A : Specifications

Physical Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Appendix B : Display Controller and Modes

Display controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1

Video modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1

Appendix C : Wireless LAN

Card Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1

Radio Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1

Supported Frequency Sub-bands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2

Appendix D : TOSHIBA RAID

Setting up Windows Manually . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-2

Starting, Modifying and Ending the BIOS Setup Program . . . . . . . . . . . . . . . . . . . D-4

Appendix E : AC Power Cord and Connectors

Certification agencies. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-1

Appendix F : If your computer is stolen

Glossary

Index

User’s Manual vii

Table of Contents

viii User’s Manual

PORTÉGÉ S100

General Precautions

TOSHIBA computers are designed to optimize safety, minimize strain and
withstand the rigors of portability. However, certain precautions should be
observed to further reduce the risk of personal injury or damage to the
computer.

Be certain to read the general precautions below and to note the cautions
included in the text of the manual.

Stress injury

Carefully read the Instruction Manual for Safety & Comfort. It contains
information on prevention of stress injuries to your hands and wrists than
can be caused by extensive keyboard use. Chapter 3, Getting Started, also
includes information on work space design, posture and lighting that can
help reduce physical stress.

Heat injury

■ Avoid prolonged physical contact with the computer. If the computer is

used for long periods, its surface can become very warm. While the
temperature will not feel hot to the touch, if you maintain physical
contact with the computer for a long time (if you rest the computer on
your lap, or if you keep your hands on the palm rest, for example) your
skin might suffer low-heat injury.

■ If the computer has been used for a long time, avoid direct contact with

the metal plate supporting the I/O ports. It can become hot.

■ The surface of the AC adaptor can become hot when in use. This

condition does not indicate a malfunction. If you need to transport the
AC adaptor, disconnect it and let it cool before moving it.

■ Do not lay the AC adaptor on a material that is sensitive to heat.

The material could be damaged.

Pressure or impact damage

Do not apply heavy pressure to the computer or subject it to strong impact.
Excessive pressure or impact can cause damage to computer components
or otherwise cause malfunctions.

User’s Manual ix

General Precautions

PC card overheating

Some PC cards can become hot with prolonged use. Overheating of a PC
card can result in errors or instability in the PC card operation. Also be
careful when you remove a PC card that has been used for a long time.

Mobile phones

Use of mobile phones can interfere with the audio system. Computer
operation is not impaired but it is recommended that a distance of 30 cm be
maintained between the computer and a mobile phone in use.

Disclaimers

LCD

Over a period of time, and depending on the usage of the computer,
the brightness of the LCD screen will deteriorate. This is an intrinsic
characteristic of LCD technology.

Maximum brightness is only available when operating in AC power mode.
Screen will dim when the computer is operated on battery power and you
may not be able to increase the brightness of the screen.

CPU

Central Processing Unit (“CPU”) Performance Disclaimer.
CPU performance in your computer product may vary from specifications

under the following conditions:

■ use of certain external peripheral products

■ use of battery power instead of AC power

■ use of certain multimedia, computer generated graphics or video

applications

■ use of standard telephone lines or low speed network connections

■ use of complex modeling software, such as high end computer aided

design applications

■ use of several applications or functionalities simultaneously

■ use of computer in areas with low air pressure

(high altitude >1,000 meters or >3,280 feet above sea level)

■ use of computer at temperatures outside the range of 5°C to 30°C

(41°F to 86°F) or >25°C (77°F) at high altitude (all temperature
references are approximate and may vary depending on the specific
computer model - please refer to your PC documentation or visit the
Toshiba website at www.pcsupport.toshiba.com for details).

CPU performance may also vary from specifications due to design
configuration.

x User’s Manual

General Precautions

Under some conditions, your computer product may automatically
shut-down. This is a normal protective feature designed to reduce the risk
of lost data or damage to the product when used outside recommended
conditions. To avoid risk of lost data, always make back-up copies of data
by periodically storing it on an external storage medium. For optimum
performance, use your computer product only under recommended
conditions. Read additional restrictions under “Environmental Conditions”
in your PC documentation. Contact Toshiba technical service and support,
refer to TOSHIBA support section in Chapter 9 Troubleshooting for more
information.

Copy Protection

Copy protection technology included in certain media may prevent or limit
recording or viewing of the media.

HDD Drive Capacity

1 Gigabyte (GB) means 1000 × 1000 × 1000 = 1,000,000,000 bytes
using powers of 10. The computer operating system, however,
reports storage capacity using powers of 2 for the definition of
1 GB = 1024 × 1024 × 1024 = 1,073,741,824 bytes, and therefore may
show less storage capacity. Available storage capacity will also be less if
the product includes one or more pre-installed operating systems, such as
Microsoft Operating System and/or pre-installed software applications,
or media content. Actual formatted capacity may vary.

Non-applicable Icons

Certain notebook chassis are designed to accommodate all possible
configurations for an entire product series. Your selected model may not
have all the features and specifications corresponding to all of the icons or
switches shown on the notebook chassis, unless you have selected all
those features.

User’s Manual xi

General Precautions

xii User’s Manual

PORTÉGÉ S100

Preface

Congratulations on your purchase of the PORTÉGÉ S100 computer.
This powerful notebook computer provides excellent expansion capability,
including multimedia devices, and it is designed to provide years of reliable,
high-performance computing.

This manual tells how to set up and begin using your PORTÉGÉ S100
computer. It also provides detailed information on configuring your
computer, basic operations and care, using optional devices and
troubleshooting.

If you are a new user of computers or if you’re new to portable computing,
first read over the Introduction and The Grand Tour chapters to familiarize
yourself with the computer’s features, components and accessory devices.
Then read Getting Started for step-by-step instructions on setting up your
computer.

If you are an experienced computer user, please continue reading the
preface to learn how this manual is organized, then become acquainted
with this manual by browsing through its pages. Be sure to look over the

Special features section of the Introduction, to learn about features that are

uncommon or unique to the computers and carefully read HW Setup.
If you are going to install PC cards or connect external devices such as a

monitor, be sure to read Chapter 8, Optional Devices.

Manual contents

This manual is composed of the following nine chapters, six appendixes,
a glossary and an index.

Chapter 1, Introduction, is an overview of the computer’s features,
capabilities, and options.

Chapter 2, The Grand Tour, identifies the components of the computer and
briefly explains how they function.

Chapter 3, Getting Started, provides a quick overview of how to begin
operating your computer and gives tips on safety and designing your work
area.

User’s Manual xiii

Preface

Chapter 4, Operating Basics, includes instructions on using the following
devices: Touch Pad, USB floppy disk drive (optional), Ultra Slim Bay
modules, optical media drives, sound system, modem, Wireless
communication features, LAN. It also provides tips on care of the computer,
floppy disks and CD/DVDs.

Chapter 5, The Keyboard, describes special keyboard functions including
the keypad overlay and hot keys.

Chapter 6, Power and Power-Up Modes, gives details on the computer’s
power resources and battery save modes and how to set a password.

Chapter 7, HW Setup, explains how to configure the computer using the
HW Setup program.

Chapter 8, Optional Devices, describes the optional hardware available.
Chapter 9, Troubleshooting, provides helpful information on how to perform

some diagnostic tests, and suggests courses of action if the computer
doesn’t seem to be working properly.

The Appendixes provide technical information about your computer.
The Glossary defines general computer terminology and includes a list of

acronyms used in the text.
The Index quickly directs you to the information contained in this manual.

Conventions

This manual uses the following formats to describe, identify, and highlight
terms and operating procedures.

Abbreviations

On first appearance, and whenever necessary for clarity, abbreviations are
enclosed in parentheses following their definition. For example: Read Only
Memory (ROM). Acronyms are also defined in the Glossary.

Icons

Icons identify ports, dials, and other parts of your computer. The indicator
panel also uses icons to identify the components it is providing information
on.

Keys

The keyboard keys are used in the text to describe many computer
operations. A distinctive typeface identifies the key top symbols as they
appear on the keyboard. For example, Enter identifies the Enter key.

xiv User’s Manual

Key operation

Some operations require you to simultaneously use two or more keys.
We identify such operations by the key top symbols separated by a plus
sign (+). For example, Ctrl + C means you must hold down Ctrl and at the
same time press C. If three keys are used, hold down the first two and at
the same time press the third.

Preface

ABC

When procedures require an action such as
clicking an icon or entering text, the icon’s name
or the text you are to type in is represented in the
type face you see to the left.

Display

S ABC

Names of windows or icons or text generated by
the computer that appears on its display screen is
presented in the type face you see to the left.

Messages

Messages are used in this manual to bring important information to your
attention. Each type of message is identified as shown below.

Pay attention! A caution informs you that improper use of equipment or
failure to follow instructions may cause data loss or damage your
equipment.

Please read. A note is a hint or advice that helps you make best use of
your equipment.

Indicates a potentially hazardous situation, which could result in death or
serious injury, if you do not follow instructions.

User’s Manual xv

Preface

xvi User’s Manual

PORTÉGÉ S100

Introduction

This chapter provides an equipment checklist, and it identifies the
computer’s features, options and accessories.

Some of the features described in this manual may not function properly if
you use an operating system that was not preinstalled by TOSHIBA.

Equipment checklist

Carefully unpack your computer. Save the box and packing materials for
future use.

Hardware

Check to make sure you have all the following items:

■ PORTÉGÉ S100 Portable Personal Computer

■ AC adaptor and power cord (2-pin plug or 3-pin plug)

■ Modular cable for modem (optional)

Chapter 1

User’s Manual 1-1

Introduction

Software

Microsoft® Windows XP Professional

■ The following software is preinstalled:

®

■ Microsoft

■ Microsoft Internet Explorer

■ TOSHIBA Utilities

■ TOSHIBA SD Memory Boot Utility

■ DVD Video Player

■ TOSHIBA Touch pad On/Off utility

■ TOSHIBA Power Saver

■ TOSHIBA Mobile Extension

■ TOSHIBA Assist

■ TOSHIBA ConfigFree

■ TOSHIBA Zooming Utility

■ TOSHIBA PC Diagnostic Tool

■ TOSHIBA Controls

■ TOSHIBA Mic Effect

■ TOSHIBA Password Utility

■ TOSHIBA RAID Utility

■ Online manual

Windows XP Professional

Documentation and Backup Media

■ PORTÉGÉ S100 Portable Personal Computer User's Manual

■ PORTÉGÉ S100 Quickstart

■ Instruction Manual for Safety & Comfort

■ Warranty information

■ Product Recovery DVD-ROM

If any of the items are missing or damaged, contact your dealer
immediately.

1-2 User’s Manual

Features

Introduction

The computer uses TOSHIBA’s advanced Large Scale Integration (LSI),
Complementary Metal-Oxide Semiconductor (CMOS) technology
extensively to provide compact size, minimum weight, low power usage,
and high reliability. This computer incorporates the following features and
benefits:

Processor

Built-in

The computer is equipped with an Intel®
Pentium

®

M processor, which incorporates a
64 KB level 1 cache memory and a 2 MB level 2
cache memory. It also supports Enhanced Intel
SpeedStep

TM

technology.

Some models of the computers carry Intel® Centrino™ technology,
which is based on three separate technologies of Intel

®

Intel

PRO/Wireless Network Connection, and Intel® 915 Chipset Family.

®

Intel

915 Chipset Family is a model by whom Intel® Pentium® M

®

Pentium® M,

processor is installed.

Memory

Slots A 256, 512 or 1,024 MB memory module is

Video RAM 64 MB of RAM is provided for video display.

installed in the main memory slot for system
memory.

The expansion memory slot accommodates
another 256, 512 or 1,024 MB memory module.

The maximum capacity of installable memory
results as follows:

■ Built-in memory is 256 MB: A maximum of

1,280 MB

■ Built-in memory is 512 MB: A maximum of

1,536 MB

■ Built-in memory is 1,024 MB: A maximum of

2,048 MB

®

User’s Manual 1-3

Introduction

Power

Battery pack The computer is powered by one rechargeable

RTC battery The internal RTC battery backs up the Real Time

AC adaptor The AC adaptor provides power to the system

lithium-ion battery pack.

Clock (RTC) and calendar.

and recharges the batteries when they are low.
It comes with a detachable power cord.
It encloses 2-pin plug or 3-pin plug type.

Because it is universal, it can receive a range of
AC voltage from 100 to 240 volts; however,
the output current varies among different models.
Using the wrong model can damage your
computer. Refer to the AC adaptor section in
Chapter 2, The Grand Tour.

Disks

Hard disk drive Available in three sizes.

■ 40.0 billion bytes (37.26 GB)

■ 60.0 billion bytes (55.89 GB)

■ 80.0 billion bytes (74.53 GB)

Other hard disk drives may be introduced.

USB floppy disk
drive (optional)

Accommodates either 3 1/2" 1.44-megabyte or
720-kilobyte floppy disks. It connects to a USB
port.

Computers in this series can be configured with an optical media drive
installed in the Ultra Slim Bay. The available optical media drives are
described below.

1-4 User’s Manual

Introduction

DVD-ROM&CD-R/RW
drive

DVD Super Multi
drive

Some models are equipped with a full-size,
DVD-ROM&CD-R/RW drive module that lets you
run CD/DVDs without using an adaptor. It reads
DVD-ROMs at maximum 8 speed and CD-ROMs
at maximum 24 speed. It writes CD-R at
maximum 24 speed and CD-RW at maximum
24 speed. The drive supports the following
formats:

■ CD-R

■ CD-RW

■ DVD-ROM

■ DVD-Video

■ CD-DA

■ CD-Text

■ Photo CD™ (single/multi-session)

■ CD-ROM Mode 1, Mode 2

■ CD-ROM XA Mode 2 (Form1, Form2)

■ Enhanced CD (CD-EXTRA)

■ Addressing Method 2

Some models are equipped with a full-size DVD
Super Multi drive module that lets you record
data to rewritable CD/DVDs as well as run either
12cm (4.72") or 8cm (3.15") CD/DVDs without
using an adaptor. It reads DVD-ROMs at
maximum 8 speed and CD-ROMs at maximum
24 speed. It writes CD-R at maximum 24 speed,
CD-RW at maximum 10 speed, DVD-R at
maximum 2 speed, DVD-RW at maximum
2 speed. DVD+R and DVD+RW at maximum

2.4 speed. DVD-RAM at maximum 2 speed. This
drive supports the following formats in addition to
DVD-ROM&CD-R/RW drive.

■ DVD-R

■ DVD-RW

■ DVD+R

■ DVD+RW

■ DVD-RAM

User’s Manual 1-5

Introduction

Display

The computer’s LCD display panel supports high-resolution video graphics.
The LCD screen can be set at a wide range of viewing angles for maximum
comfort and readability.

Built-in 14.1" TFT LCD screen, 16 M colors,

with one of the following resolutions:

■ XGA, 1024 horizontal × 768 vertical pixels

■ SXGA+, 1400 horizontal × 1050 vertical

pixels

Graphics controller Graphics controller maximizes display

performance. Refer to Display Controller and

Modes section in Appendix B for more

information.

Keyboard

Built-in

85 keys or 86 keys, compatible with IBM
enhanced keyboard, embedded numeric overlay,

dedicated cursor control, and keys.
Refer to Chapter 5, The Keyboard, for details.

®

Pointing Device

Built-in Touch Pad A Touch Pad and control buttons in the palm rest

enable control of the on-screen pointer and
scrolling of windows.

Ports

External monitor Analog VGA port supports VESA DDC2B

Universal Serial Bus
(USB 2.0)

compatible functions.

The computer has two Universal Serial Bus ports
that comply with the USB 2.0 standard, which
enables data transfer speeds 40 times faster
than the USB 1.1 standard (The ports also
support USB 1.1).

Docking interface This port enables connection of an optional

i.LINK™ (IEEE1394) This port enables high-speed data transfer

1-6 User’s Manual

Advanced Port Replicator III described in the

Options section.

directly from external devices such as digital
video cameras.

Introduction

Infrared The serial infrared port is compatible with

Infrared Data Association (IrDA 1.1) standards.
It enables cableless 4 Mbps, 1.152 Mbps,

115.2 kbps, 57.6 kbps, 38.4 kbps, 19.2 kbps or

9.6 kbps data transfer with IrDA 1.1 compatible
external devices.

Slots

PC card The PC card slot accommodates a Type II card.

SD card This slot lets you easily transfer data from

devices, such as digital cameras and
Personal Digital Assistants, that use SD card
flash-memory.

Refer to Chapter 8, Optional Devices.

Multimedia

Sound system Windows sound system compatible sound

system provides internal speakers and a
microphone as well as jacks for an external
microphone and headphones.

Headphone jack A 3.5 mm mini headphone jack enables

connection of stereo headphones.

Microphone jack A 3.5 mm mini microphone jack enables

connection of a three-conductor mini jack for
monaural microphone input.

Communications

Modem An internal modem provides capability for data

and fax communication. It supports V.90 (V.92).
The speed of data transfer and fax depends on
analog telephone line conditions. It has a modem
jack for connecting to a telephone line. Both of
V.90 and V.92 are supported only in USA,
Canada, UK, France, Germany and Australia.
Only V.90 is available in other regions.

LAN The computer has built-in support for Ethernet

LAN (10 megabits per second, 10BASE-T),
Fast Ethernet LAN (100 megabits per second,
100BASE-TX) and Gigabit Ethernet LAN
(1000 megabits per second, 1000BASE-T).

User’s Manual 1-7

Introduction

Wireless LAN Some computers in this series are equipped with

a Wireless LAN mini-PCI card that is compatible
with other LAN systems based on Direct
Sequence Spread Spectrum/Orthogonal
Frequency Division Multiplexing radio technology
that complies with the IEEE 802.11 Standard
(Revision A, B or G).

■ Theoretical maximum speed:

54Mbps(IEEE802.11a, 802.11g)

■ Theoretical maximum speed:

11Mbps(IEEE802.11b)

■ Frequency Channel Selection

(5 GHz: Revision A / 2.4 GHz: Revision B/G)

■ Roaming over multiple channels

■ Card Power Management

■ Wired Equivalent Privacy (WEP) data

encryption, based on 128 bit encryption
algorithm (Intel module type).

■ Wi-Fi Protected Access (WPA).

■ The numerical values for display are the theoretical maximums for

Wireless LAN standards. The actual values may differ.

■ The transmission speed over the Wireless LAN and the distance over

which Wireless LAN can reach may vary depending on surrounding
electromagnetic environment, obstacles, access point design and
configuration, and client design and software/hardware configurations.
The Transmit Rate (at X Mbit/s) is the theoretical maximum speed
under the IEEE802.11 (a/b/g) standard. The actual transmission speed
will be lower than the theoretical maximum speed.

Wireless
communication

This switch turns the Wireless LAN functions on
and off.

switch

Ultra Slim Bay
Modules

Ultra Slim Bay is a single-drive bay that
accommodates a DVD-ROM&CD-R/RW drive,
DVD Super Multi drive and secondary hard disk
drive. The TOSHIBA Mobile Extension enables
hot insertion of modules when you are using a
plug and play operating system.

Ultra Slim Bay
Weight Saver

1-8 User’s Manual

To reduce weight, the Ultra Slim Bay module can
be removed and a weight saver installed.

Security

Introduction

Security lock slot Connects an optional security lock to anchor the

Ultra Slim Bay lock Ultra Slim Bay module can be secured by Ultra

Special features

The following features are either unique to TOSHIBA computers or are
advanced features, which make the computer more convenient to use.

TOSHIBA Assist
button

TOSHIBA
Presentation button

Hot keys Key combinations let you quickly change the

Display automatic
power off

HDD automatic
power off

computer to a desk or other large object.

Slim Bay lock fixed with a lock screw in the lock
position. The lock screw is inserted in the unlock
position when purchased.

Press this button to launch an application
automatically. The default is TOSHIBA Assist.

Press this button to change internal display,
external display, simultaneous display,
or multi-monitor display.

system configuration directly from the keyboard
without running a system configuration program.

This feature automatically cuts off power to the
computer’s LCD display panel when there is no
keyboard input for a time specified. Power is
restored when any key is pressed. You can
specify the time in the Monitor power off item of
the Basic Setup tab in TOSHIBA Power Saver.

This feature automatically cuts off power to the
hard disk drive when it is not accessed for a time
specified. Power is restored when the hard disk is
accessed. You can specify the time in the HDD
power off item of the Basic Setup tab in TOSHIBA
Power Saver.

System automatic
Standby/Hibernation

Keypad overlay A ten-key pad is integrated into the keyboard.

User’s Manual 1-9

This feature automatically shuts down the system
in standby mode or Hibernation mode when there
is no input or hardware access for a time
specified. You can specify the time and select
either System Standby or System hibernation in
the System standby and System item of the Basic
Setup tab in TOSHIBA Power Saver.

Refer to the Keypad overlay section in Chapter 5,
The Keyboard, for instructions on using the
keypad overlay.

Introduction

Power on password Two levels of password security, supervisor and

user, are available to prevent unauthorized
access to your computer.

Instant security A hot key function blanks the LCD screen and

disables the computer providing data security.

Intelligent power
supply

A microprocessor in the computer’s intelligent
power supply detects the battery’s charge and
calculates the remaining battery capacity. It also
protects electronic components from abnormal
conditions, such as voltage overload from an AC
adaptor. You can monitor remaining battery
capacity. Use the Battery remaining item in
TOSHIBA Power Saver.

Battery save mode This feature lets you save battery power. You can

specify the Power Save Mode in the Profile item
in TOSHIBA Power Saver.

Panel power on/off This feature turns power to the computer off

when the computer’s LCD display panel is closed
and turns it back on when the computer’s LCD
display panel is opened. You can specify the
setting in the When I close the lid item of the
Setup Action tab in TOSHIBA Power Saver.

Low battery
automatic
hibernation

When battery power is exhausted to the point that
computer operation cannot be continued, the
system automatically enters Hibernation and
shuts down. You can specify the setting in the
Setup Action tab in TOSHIBA Power Saver.

Heat dispersal To protect from overheating, the CPU has an

internal temperature sensor. If the computer’s
internal temperature rises to a certain level,
the cooling fan is turned on or the processing
speed is lowered. Use the Cooling Method item
of the Basic Setup tab in TOSHIBA Power Saver.

■ Maximum

Performance

Turns on fan first, then if
necessary lowers CPU
processing speed.

■ Performance Uses a combination of

fan and lowering the
CPU processing speed.

■ Battery optimized Lowers the CPU

processing speed first,
then if necessary turns
on the Cooling Method.

1-10 User’s Manual

Introduction

Optical media drive
power icon

Use this to turn the power of the optical media
drive on or off. Clicking on the optical media drive
icon on the taskbar will turn the power of the
optical media drive on or off. If the optical media
drive power is off, the disc tray will not open even
if the eject button is pushed. The power of the
optical media drive can be turned on using the
optical media drive icon.

HDD Protection Using the acceleration sensor built in the

computer, HDD Protection detects vibration,
shocks, and those signs in the computer, and
automatically moves the HDD (Hard Disk Drive)
head to the safe position to reduce the risk of
damage that could be caused to the disk by
head-to-disk contact. Refer to the Using the Hard

Disk Drive (HDD) Protection section in Chapter 4,

Operating Basics, for details.

This function does not guarantee that the HDD will not be damaged.

Hibernation This feature lets you turn off the power without

exiting from your software. The contents of main
memory are saved to the hard disk, when you
turn on the power again, you can continue
working right where you left off. Refer to the

Turning off the power section in Chapter 3,

Getting Started, for details.

Standby If you have to interrupt your work, you can turn off

the power without exiting from your software.
Data is maintained in the computer’s main
memory. When you turn on the power again,
you can continue working right where you left off.

TOSHIBA RAID RAID (Redundant Array of Independent Disks)

realizes fault tolerance (mirroring = RAID1),
which is configured by arraying multiple
independent hard disk drives. This feature is only
available when a secondary hard disk drive is
installed in the Ultra Slim Bay.

User’s Manual 1-11

Introduction

Utilities

This section describes preinstalled utilities and tells how to start them.
For details on operations, refer to each utility’s online manual, help files or
readme.txt files.

TOSHIBA Power
Saver

HW Setup This program lets you customize your hardware

TOSHIBA Controls This utility have a section to let you do the

DVD Video Player The DVD Video Player is used to play

TOSHIBA SD
Memory Boot Utility

To access this power savings management
program, click start, click Control Panel,
click Performance and Maintenance and select
the TOSHIBA Power Saver icon.

settings according to the way you work with your
computer and the peripherals you use. To start
the utility, To access this utility, click start,
click Control Panel, click Printers and Other
Hardware and select the TOSHIBA HWSetup
icon.

following:

■ Buttons: Assign applications or functions to

the TOSHIBA Presentation button (default
setting is the simultaneous display on LCD
and CRT with resolution of 1024 × 768) and
to the TOSHIBA Assist button (default setting
is the TOSHIBA Assist).

DVD-Video. It has an on-screen interface and
functions. Click start, point to All Programs,
point to InterVideo WinDVD, then click
InterVideo WinDVD.

The TOSHIBA SD memory boot utility is a utility
which can create SD memory card to a boot disk.
You can boot TOSHIBA SD Memory Boot Utility
from the menu bar as follows. Click start, point to

All Programs, point to TOSHIBA, point to
Utilities and click SD Memory Boot Utility.

TOSHIBA Zooming
Utility

RecordNow! Basic
for TOSHIBA

1-12 User’s Manual

This utility allows you to enlarge or reduce the
icon size on the desktop or the application
window.

You can create CD/DVDs in several formats
including audio CDs that can be played on a
standard stereo CD player and data CD/DVDs to
store the files and folders on your hard disk drive.
This software can be used on a model with
DVD-ROM&CD-R/RW drive and DVD Super
Multi drive.

Introduction

TOSHIBA Assist TOSHIBA Assist is a graphical user interface that

provides easy access to help and services. It is
the default function launched by the TOSHIBA
Assist button.

TOSHIBA PC
Diagnostic Tool

TOSHIBA PC Diagnostic Tool displays the basic
information on PC, and the test of built-in devices
can also be performed. To start TOSHIBA PC
Diagnostic Tool, click start, point to All
Programs, point to TOSHIBA, point to Utilities
and click PC Diagnostic Tool.

TOSHIBA Mobile
Extension

This utility supports docking your computer to an
optional Advanced Port Repricator III. To open
the property dialog, select TOSHIBA Mobile
Extension from TOSHIBA Assist.

TOSHIBA ConfigFree TOSHIBA ConfigFree is a suite of utilities to

allow easy control of communication devices and
network connections. TOSHIBA ConfigFree also
allows you to find communication problems and
create profiles for easy switching between
locations and communication networks. To start
ConfigFree, click start, point to All Programs,
point to TOSHIBA, point to Networking and click

ConfigFree.

TOSHIBA Touch Pad
On/Off Utility

This utility has the following function.
To disable/enable the Touch Pad with

Fn + F9 key.

TOSHIBA Mic Effect This utility provides you with a hands-free

environment for holding mutual communication
via the Internet Protocol or Local Area Network.
Refer to the Sound System section in Chapter 4,
Operating Basics, for details.

User’s Manual 1-13

Introduction

TOSHIBA RAID
Console

If a secondary hard disk drive is installed in the
Ultra Slim Bay in addition to the built-in HDD,
you can use the TOSHIBA RAID Console to
create or manage a RAID array.

To start the utility, click start, point to All
Programs, point to TOSHIBA, point to RAID and
click RAID Console.

It is possible to change to RAID1 (mirroring) from
a non-RAID configuration (default).

Caution: When RAID1 is set, you cannot change
your setting unless you completely restore your
preinstalled software.

It is strongly recommended to read the TOSHIBA
RAID Help before you change any of the
settings.

NVIDIA Rotation
Settings

This utility let you rotate the desktop by 0 and
180 easily. It can rotate by clicking the icon
in a taskbar or pressing Ctrl + Shft + R.
In a multi-monitor setup, the display that
contains the cursor is effective.

TOSHIBA Password
Utility

This utility lets you set a password that restricts
access to the computer.

Sound drivers A broad range of audio controls are available

through the ADI sound driver, including Software
Synthesize, Mic Volume, Noise Reduction and
Audio Power Management.

Click start, click Control Panel and click
SoundMAX icon to change the Mic Noise
Reduction settings and the Power Management
settings. If you are viewing the Control Panel in
Category View, click on Switch to Classic View.

For other sound settings, use the Windows
Device Manager, Multimedia Panel or Volume
Dial.

1-14 User’s Manual

Introduction

TOSHIBA
Accessibility

This utility lets you make the Fn key sticky, that
is, you can press it once, release it, and they
press an “F number” key. The Fn key remains
active until another key is pressed.

DLA for TOSHIBA DLA (Drive Letter Access) is the packet writing

software which provides the function which writes
files and/or folders to DVD-RW, CD-RW and
DVD+RW discs via a drive letter like a floppy disk
or other removable disks.

TOSHIBA Hotkey
Utility for Display
Devices

This utility has the change of a display device,
and the function to change display resolution.
Press Fn + F5 to change the active display
device. Press Fn + Space keys to change the
display resolution.

TOSHIBA SD
Memory Card Format

CD/DVD Drive
Acoustic Silencer

This utility has the function which formats SD
memory card by SD standard format.

This utility has the function to set up the read
speed of CD.

It is ineffective in DVD.
You can set up one of the modes: [Normal Mode]

can read data early, and [Quiet Mode] can lessen
noise.

User’s Manual 1-15

Introduction

Options

You can add a number of options to make your computer even more
powerful and convenient to use. The following options are available:

Memory expansion A 256, 512 or 1,024 MB memory module

(DDR2-533/400) can easily be installed in the
computer.

Battery pack An additional battery pack can be purchased

from your TOSHIBA dealer. Use it as a spare or
replacement.

High capacity battery
pack

An additional battery pack can be purchased
from your TOSHIBA dealer. Use it as a spare or
replacement.

AC adaptor If you use your computer at more than one site

Battery charger The battery charger lets you charge extra

Security lock A slot is available to attach a security cable to the

USB floppy disk Kit USB floppy disk drive accommodates

Advanced Port
Replicator III

Hard disk drive You can increase your computer's data storage

frequently, it may be convenient to purchase an
additional AC adaptor for each site so you will not
have to carry the adaptor with you.

batteries outside the computer.

computer to deter theft.

1.44-megabyte or 720-kilobyte floppy disk.
It connects to a USB port. (You cannot format
720-kilobyte floppy disks on Windows XP,
but you can use previously formatted disks.)

The Advanced Port Replicator III provides the
ports available on the computer in addition to
separate PS/2 mouse and PS/2 keyboard ports,
a digital visual interface (DVI) port, i.LINK™
(IEEE1394) port, line-in jack and line-out jack,
External monitor port, Universal Serial Bus port
(USB2.0) × 4, LAN jack, Modem jack, Serial port,
Parallel port.

capacity with additional hard disk drives.
They are available in the following sizes:

■ 40 billion bytes (37.26 GB)

■ 60 billion bytes (55.89 GB)

■ 80 billion bytes (74.53 GB)

Wireless LAN Kit This option enables wireless LAN functions in

1-16 User’s Manual

computers that do not have wireless preinstalled.
It is installed by dealers only.

Introduction

Ultra Slim Bay options

The following modules can be installed in the Ultra Slim Bay. All other
modules are options.

DVD-ROM&CD-R/RW Refer to the Features section for details.

DVD Super Multi Refer to the Features section for details.

Ultra Slim Bay HDD
adaptor (Black)

An adaptor lets you install an optional HDD
described in Chapter 8, Optional Devices.

Hard disk drive You can increase your computer’s data storage

capacity with an additional 40 billion bytes
(37.26 GB), 60 billion bytes (55.89 GB),
80 billion bytes (74.53 GB) hard disk drive in the
Ultra Slim Bay HDD adaptor.

Ultra Slim Bay Case Store the DVD Super Multi drive unit in this case

when removing it from the computer or
transporting it.

User’s Manual 1-17

Introduction

1-18 User’s Manual

PORTÉGÉ S100

The Grand Tour

This chapter identifies the various components of your computer. Become
familiar with each component before you operate the computer.

Certain notebook chassis are designed to accommodate all possible
configurations for an entire product series. Your selected model may not
have all the features and specifications corresponding to all of the icons or
switches shown on the notebook chassis, unless you have selected all
those features.

Front with the display closed

The following figure shows the computer’s front with its LCD display panel
in the closed position.

System
indicators

Microphone jack Headphone jack

Chapter 2

Display latch

Wireless communication switch

Front of the computer with LCD display panel closed

System indicators LEDs let you monitor the status of various

Wireless
communication
switch

User’s Manual 2-1

Volume control

computer functions. Details are given in the

System indicators section.

Slide this switch to the left to turn off Wireless
LAN function. Slide it to the right to turn on the
functions.

Some models are equipped with Wireless
communication.

Infrared port

Microphone

The Grand Tour

Set the switch to off in airplanes and hospitals. Check the wireless
communication indicator. It will stop glowing when the wireless
communication function is off.

Microphone jack A 3.5 mm mini microphone jack enables

connection of a three-conductor mini jack for
monaural microphone input.

Headphone jack A 3.5 mm mini headphone jack enables

connection of stereo headphones.

Volume control Use this dial to adjust the volume of the stereo

speakers and the stereo headphones.

Left side

Display latch This latch secures the LCD panel in its closed

position. Push the latch to open the display.

Infrared port This infrared port is compatible with Infrared Data

Association (IrDA 1.1) standards. It enables
cableless 4 Mbps, 1.15 Mbps, 115.2 kbps,

57.6 kbps, 38.4 kbps, 19.2 kbps or 9.6 kbps data
transfer with IrDA 1.1 compatible external
devices.

Microphone A built-in microphone lets you record sound into

your applications. Refer to the Using the

microphone section in Chapter 4, Operating

Basics.

The following figure shows the computer’s left side.

LAN active
indicator (orange)

Link indicator (green)

Cooling vents

LAN jack

The left side of the computer

Security lock slot

i.LINK (IEEE1394) port

PC card eject
button

PC card slot

SD card slot

2-2 User’s Manual

The Grand Tour

LAN jack This jack lets you connect to a LAN. The adaptor

has built-in support for Ethernet LAN (10
megabits per second, 10BASE-T), Fast Ethernet
LAN (100 megabits per second, 100BASE-TX)
and Gigabit Ethernet LAN (1000 megabits per
second, 1000BASE-T). The LAN has two
indicators. Refer to Chapter 4, Operating Basics,
for details.

■ Do not connect any cable other than a LAN cable to the LAN jack.

It could cause damage or malfunction.

■ Do not connect the LAN cable to a power supply. It could cause

damage or malfunction.

Link indicator
(green)

This indicator glows green when the computer is
connected to a LAN and the LAN is functioning
properly.

LAN active indicator
(orange)

This indicator glows orange when data is being
exchanged between the computer and the LAN.

Cooling vents Cooling vents help CPU keep from overheating.

Do not block the cooling vents. Do not insert or allow foreign objects to
enter the cooling vents. If pins or similar objects are inserted into the
computer, the computer’s circuitry may be damaged.

Security lock slot A security cable attaches to this slot. The

optional security cable anchors your computer to
a desk or other large object to deter theft.

i.LINK (IEEE1394)
port

Connect an external device, such as a digital
video camera to this port for high-speed data
transfer.

PC card slot The PC card slot can accommodate a Type II

card. The slot supports 16-bit PC cards and
CardBus PC cards.

PC card eject button This is a button for taking out PC card from a PC

card slot.

Keep foreign objects out of the PC card slot. A pin or similar object can
damage the computer’s circuitry.

SD card slot SD cards are used in a wide variety of external

devices. This slot lets you transfer data from the
device to your computer.

User’s Manual 2-3

The Grand Tour

Keep foreign objects out of the SD card slot. A pin or similar object can
damage the computer’s circuitry.

Right side

The following figure shows the computer’s right side.

Ultra Slim Bay

External monitor port

The right side of the computer

Ultra Slim Bay A DVD-ROM&CD-R/RW drive, DVD Super Multi

External monitor
port

Back side

The following figure shows the computer’s back side.

Universal Serial Bus
(USB 2.0) ports

drive and Ultra Slim Bay HDD adaptor can be
installed in the Ultra Slim Bay. A weight saver can
be installed when there is no module.

This external monitor port lets you connect an
external video display.

Modem jackDC IN 15V jack

USB ports

The back side of the computer

Two Universal Serial Bus ports are on the
back side. The ports comply with the USB 2.0
standard, which enables data transfer speeds
40 times faster than the USB 1.1 standard
(The ports also support USB 1.1).

2-4 User’s Manual

The Grand Tour

Keep foreign objects out of the USB connectors. A pin or similar object can
damage the computer’s circuitry.

Operation of all functions of all USB devices has not been confirmed.
Some functions might not execute properly.

DC IN 15V jack The AC adaptor connects to this jack. Use only

the model of AC adaptor that comes with the
computer. Using the wrong adaptor can damage
your computer.

Modem jack The modem jack lets you use a modular cable to

■ In case of a lightning storm, unplug the modular cable from the

■ Do not connect the modem to a digital telephone line. A digital line will

Underside

The following figure shows the underside of the computer. Make sure the
display is closed before turning over your computer.

telephone jack.

damage the modem.

Battery lock

Ultra Slim Bay

Ultra Slim Bay

lock

Battery pack

connect the modem directly to a telephone line.

Notches

Battery release
latch

Docking
Interface

Memory
module cover

HDD pack cover screw

The underside of the computer

User’s Manual 2-5

Ultra Slim Bay lock screw

The Grand Tour

Battery lock Slide this lock to release the battery pack for

removal.

Battery pack The battery pack powers the computer when

the AC adaptor is not connected. For detailed
information on the battery pack, refer to
Chapter 6, Power and Power-Up Modes.

Notches Notches on the computer engage hooks on the

Advanced Port Replicator III to hold the connection
securely.

Battery release
latch

Slide and hold this latch to release the battery pack
for removal.

For detailed information on removing the battery
packs, refer to Chapter 6, Power and Power-Up

Modes.

Docking interface This port enables connection of an optional

Advanced Port Replicator III described in Chapter 8,

Optional Devices.

Keep foreign objects out of the docking interface port. A pin or similar
object can damage the computer's circuitry. A plastic shutter protects the
connector.

Ultra Slim Bay See the Right side section in this chapter for details.

Ultra Slim Bay
lock

Slide the lock to release or secure the Ultra Slim Bay
ejector.

Be sure to lock the Ultra Slim Bay lock before you transport or carry the
computer.

Ultra Slim Bay

One screw secures the Ultra Slim Bay lock.

lock screw

Memory module
cover

This cover protects one of the memory module
sockets. The other memory module is located under
the keyboard. Refer to the Memory expansion
section in Chapter 8, Optional Devices.

HDD pack cover

One screw secures the HDD cover.

screw

2-6 User’s Manual

Front with the display open

This section shows the computer with the LCD display panel open. Refer to
the appropriate illustration for details. To open the display, push the display
latch on the front of the LCD display panel and lift up. Position the LCD
display panel at a comfortable viewing angle.

Display hinge

The Grand Tour

LCD screen

Stereo speaker (Right)

Touch Pad

Stereo speaker

(Left)

Power button

LCD Sensor switch

(Not shown)

TOSHIBA Assist Button

The front of the computer with the LCD panel open

TOSHIBA Presentation Button

Touch Pad
control buttons

Display hinge The display hinge holds the LCD display panel at

easy-to-view angles.

LCD screen The LCD screen displays high-contrast text and

graphics. The available resolution depends on
the model. With XGA, you can change the
resolution between 800 × 600 and
1024 × 768 pixels. With SXGA, between
800 × 600 and 1400 × 1050 pixels.
Refer to Display Controller and Modes section in
Appendix B.

When the computer operates on the AC adaptor
the LCD screen’s image will be somewhat
brighter than when it operates on battery power.
The lower brightness level is intended to save
battery power.

User’s Manual 2-7

The Grand Tour

Stereo speakers The speakers emit sound generated by your

software as well as audio alarms, such as low
battery condition, generated by the system.

Touch Pad control
buttons

Control buttons below the Touch Pad let you
select menu items or manipulate text and
graphics designated by the on-screen pointer.

Touch Pad A Touch Pad located in the center of the palm

rest is used to control the on-screen pointer.
Refer to the Using the Touch Pad section in
Chapter 4, Operating Basics.

TOSHIBA
Presentation button

Press this button to change internal display,
simultaneous display, or multi-monitor display.

The default setting is the simultaneous display on
LCD and CRT with resolution of 1024 × 768.
When you press this button twice, the display
mode returns to single display on LCD only.
Setting of multi-monitor display in Windows XP,
computer changes its display mode to the
multi-monitor display on LCD and CRT.
You can also return to single display by pressing
this button twice.

The setting of TOSHIBA Presentation button can
be changed through the properties of TOSHIBA
Controls. Display mode is changed to the
multi-monitor display by selecting “Different
Image” (Windows XP only) or to the
simultaneous display on internal and external
display by selecting “Same Image”.

TOSHIBA Assist
button

Press this button to launch the program
automatically. When power-off, stand-by and
hibernation, press this button to start the
computer and launch the program.

You can select the function on TOSHIBA
Controls properties.

The default is TOSHIBA Assist.

2-8 User’s Manual

Power button Press the power button to turn the computer’s

LCD Sensor switch This switch senses when the computer’s LCD

Do not put a magnetic object close to the switch. The computer will
automatically enter Hibernation mode and shut down even if the Panel
Power Off features is disabled.

System indicators

LEDs beneath icons, light when various computer operations are in
progress.

The Grand Tour

power on and off.

display panel is closed or opened and activates
the Panel Power Off/On feature. When you close
the LCD display panel the computer enters
Hibernation mode and shuts down. When you
open the computer's LCD display panel the
computer starts in Hibernation mode. Use the
TOSHIBA Power Saver Utility to enable or
disable this feature. The default is “enabled”.

Refer to the TOSHIBA Power Saver Utility and
Panel Power Off/On items in Chapter 1, Special

features, for details on settings.

System indicators

SD card The SD card indicator glows green when the

computer is accessing the SD card slot.

DC IN The DC IN indicator glows in green when DC

Power The Power indicator glows in green when the

User’s Manual 2-9

power is supplied from the AC power adaptor.
If the adaptor’s output voltage is abnormal or if
the power supply malfunctions, this indicator
flashes orange.

computer is on. If you select Standby from Shut
Down Windows, this indicator blinking orange
(one second on, two seconds off) while the
computer shuts down.

The Grand Tour

Battery The Battery indicator shows the condition of the

battery’s charge: Green indicates full charge,
orange indicates battery charging and flashing
orange indicates a low battery charge. Refer to
Chapter 6, Power and Power-Up Modes.

HDD The HDD indicator glows green when the

computer is accessing the built-in hard disk.

Wireless
communication

Keyboard indicators

The figures below show the positions of the keypad overlay indicators and
the Caps Lock indicator.

When the Arrow mode indicator glows the keypad overlay lets you control
the cursor.

When the Numeric mode indicator glows the keypad overlay lets you enter
numbers.

When the Caps Lock indicator glows the keyboard is in all-caps mode.

The Wireless communication indicator glows
when the wireless LAN function is turned on.

Some models are equipped with a Wireless
communication.

Caps Lock indicator

Caps Lock indicator

Caps Lock This indicator glows green when the alphabet

keys are locked in uppercase.

2-10 User’s Manual

Arrow mode

indicator

Keypad overlay indicators

The Grand Tour

Numeric mode
indicator

Arrow mode When the Arrow mode indicator lights green,

you can use the keypad overlay (gray labeled
keys) as cursor keys. Refer to the Keypad

overlay section in Chapter 5, The Keyboard.

Numeric mode You can use the keypad overlay (gray labeled

keys) for numeric input when the Numeric mode
indicator lights green. Refer to the Keypad

overlay section in Chapter 5, The Keyboard.

USB floppy disk drive (optional)

The optional USB floppy disk drive accommodates 1.44-megabyte or
720-kilobyte floppy disks. It connects to a USB port.

USB connector

Disk-In-Use
Indicator

Floppy disk slot

USB floppy disk drive

Eject button

USB connector Insert this connector to the USB port of your

computer.

Disk-In-Use Indicator This indicator lights when the floppy disk is being

accessed.

User’s Manual 2-11

The Grand Tour

Floppy disk slot Insert a floppy disk in this slot.

Eject button When a floppy disk is fully seated in the drive,

Check the Disk-In-Use indicator when you use the USB floppy disk drive.
Do not press the eject button or turn off the computer while the light is
glowing. Doing so could destroy data and damage the floppy disk or the
drive.

■ The USB floppy disk drive should be placed on a flat, horizontal surface

when in use. Do not set the drive on an incline greater than 20o while it
is operating.

■ Do not set anything on top of the floppy disk drive.

Optical media drives

One of the following optical media drives is installed in the computer:
DVD-ROM&CD-R/RW and DVD Super Multi drives. An ATAPI interface
controller is used for CD/DVD-ROM operation. When the computer is
accessing a CD/DVD, an indicator on the drive glows.

For information on loading and unloading discs refer to the Using optical

media drives section in Chapter 4, Operating Basics.

the eject button pops out. To remove a floppy
disk, push in the eject button and the floppy disk
pops out partially for removal.

Region codes for DVD drives and media

DVD-ROM&CD-R/RW, DVD Super Multi drives and media are
manufactured according to the specifications of six marketing regions.
When you purchase DVD-Video, make sure it matches your drive,
otherwise it will not play properly.

Code Region

1 Canada, United States

2 Japan, Europe, South Africa, Middle East

3 Southeast Asia, East Asia

4 Australia, New Zealand, Pacific Islands, Central America,

South America, Caribbean

5 Russia, Indian Subcontinent, Africa, North Korea, Mongolia

6 China

2-12 User’s Manual

Writable discs

This section describes the types of writable CD/DVD discs. Check the
specifications for your drive to for the type of discs it can write. Use
RecordNow! to write compact discs. Refer to Chapter 4, Operating Basics.

CDs

■ CD-R discs can be written only once. The recorded data cannot be

erased or changed.

■ CD-RW discs including multi speed CD-RW discs, high-speed CD-RW

discs, ultra-speed CD-RW discs can be recorded more than once.

DVDs

■ DVD-R and DVD+R discs can be written only once. The recorded data

cannot be erased or changed.

■ DVD-RW, DVD+RW and DVD-RAM discs can be recorded more than

once.

Formats

The drives support the following formats:

The Grand Tour

■ CD-ROM

■ DVD-ROM

■ CD-DA

TM

■ Photo CD

■ CD-ROM XA Mode 2

(Form1, Form2)

(single/multi-session)

■ DVD -Video

■ CD-Text

■ CD-ROM Mode 1, Mode 2

■ Enhanced CD (CD-EXTRA)

■ Addressing Method 2

DVD-ROM&CD-R/RW drive

The full-size DVD-ROM&CD-R/RW drive module lets you record data to
rewritable CDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs
without using an adaptor.

The read speed is slower at the center of a disc and faster at the outer
edge.

DVD read 8 speed (maximum)
CD read 24 speed (maximum)
CD-R write 24 speed (maximum)
CD-RW write 24 speed (maximum, Ultra-speed media)

User’s Manual 2-13

The Grand Tour

DVD Super Multi drive

The full-size DVD Super Multi drive module lets you record data to
rewritable CDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs
without using an adaptor.

The read speed is slower at the center of a disc and faster at the outer
edge.

DVD read 8 speed (maximum)
DVD-R write 2 speed (maximum)
DVD-RW write 2 speed (maximum)
DVD+R write 2.4 speed (maximum)
DVD+RW write 2.4 speed (maximum)
DVD-RAM write 2 speed (maximum)
CD read 24 speed (maximum)
CD-R write 24 speed (maximum)
CD-RW write 10 speed (maximum, Ultra-speed media)

AC adaptor

The AC adaptor can automatically adjust to any voltage ranging from
100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to
use this computer in almost any country/region. And the adaptor converts
AC power to DC power and reduces the voltage supplied to this computer.

To recharge the battery, simply connect the AC adaptor to a power source
and the computer. Refer to Chapter 6, Power and Power-Up Modes for
details.

The AC adaptor (2-pin plug)

2-14 User’s Manual

The Grand Tour

The AC adaptor (3-pin plug)

■ The Universal AC Adaptor and power cord bundled with this product

may differ depending on the product model. Depending on the model,
a 2-pin plug or 3-pin plug set of the above may be bundled.

■ Do not use a 3-pin to 2-pin conversion plug.

The supplied power cord conforms to safety rules and regulations in the
region the product is bought and should not be used outside this region.
For use in other regions, please buy power cords that conform to safety
rules and regulations in the particular region.

Use only the AC adaptor that came with the computer or an equivalent
optional adaptor. Use of any other adaptors could damage your computer.

TOSHIBA assumes no liability for any damage in such case.

Use only the AC adaptor supplied as an accessory. Other AC adaptors
have different voltage and terminal polarities and use of them may produce
heat and smoke or even result in fire or rupture.

User’s Manual 2-15

The Grand Tour

2-16 User’s Manual

PORTÉGÉ S100

Getting Started

This chapter provides basic information to get you started using your
computer. It covers the following topics:

■ Setting up your work space — for your health and safety

Be sure also to read Instruction Manual for Safety & Comfort. This guide,
which is included with the computer, explains product liability.

■ Connecting the AC adaptor

■ Opening the display

■ Turning on the power

■ Starting up for the first time

■ Turning off the power

■ Restarting the computer

■ Restoring the preinstalled software

Chapter 3

All users should be sure to read the section Starting up for the first time.

Setting up your work space

Establishing a comfortable work site is important for you and your
computer. A poor work environment or stressful work habits can result in
discomfort or serious injury from repetitive strain to your hands,
wrists or other joints. Proper ambient conditions should also be maintained
for the computer’s operation. This section discusses the following topics:

■ General conditions

■ Placement of the computer

■ Seating and posture

■ Lighting

■ Work habits

User’s Manual 3-1

Getting Started

General conditions

In general, if you are comfortable, so is your computer, but read the
following to make sure your work site provides a proper environment.

■ Make sure there is adequate space around the computer for proper

ventilation.

■ Make sure the AC power cord connects to an outlet that is close to the

computer and easily accessible.

■ The temperature should be 5 to 35 degrees Centigrade

(41 to 95 degrees Fahrenheit) and the relative humidity should be
20 to 80 percent.

■ Avoid areas where rapid or extreme changes in temperature or humidity

may occur.

■ Keep the computer free of dust, moisture, and exposure to direct

sunlight.

■ Keep the computer away from heat sources, such as electric heaters.

■ Do not use the computer near liquids or corrosive chemicals.

■ Do not place the computer near objects that create strong magnetic

fields (e.g., stereo speakers).

■ Some computers in the computer, including data storage media,

can be damaged by magnets. Do not place the computer near magnetic
objects or bring magnetic objects close to the computer. Be careful of
objects, such as stereo speakers, that produce strong magnetic fields
during operation. Also, be careful with metal objects, such as bracelets,
which can be inadvertently magnetized.

■ Do not operate the computer in close proximity to a mobile phone.

■ Leave ample ventilation room for the fan. Do not block the vents.

Placement of the computer

Position the computer and peripheral devices to provide comfort and safety.

■ Set the computer on a flat surface at a comfortable height and distance.

The LCD display panel should be no higher than eye level to avoid
eyestrain.

■ Place the computer so that it is directly in front of you when you work

and make sure you have adequate space to easily operate other
devices.

■ Allow adequate space behind the computer to let you freely adjust the

LCD display panel. The LCD display panel should be angled to reduce
glare and maximize visibility.

■ If you use a paper holder, set it at about the same height and distance

as the computer.

3-2 User’s Manual

Seating and posture

The height of your chair in relation to the computer and keyboard as well as
the support it gives your body are primary factors in reducing work strain.
Refer to the following tips.

Below eye level

Foot rest

Posture and positioning of the computer

■ Place your chair so that the keyboard is at or slightly below the level of

your elbow. You should be able to type comfortably with your shoulders
relaxed.

■ Your knees should be slightly higher than your hips. If necessary, use a

foot rest to raise the level of your knees to ease pressure on the back of
your thighs.

■ Adjust the back of your chair so it supports the lower curve of your

spine.

■ Sit straight so that your knees, hips and elbows form approximately

90 degree angles when you work. Do not slump forward or lean back
too far.

Getting Started

90°angles

Lighting

Proper lighting can improve legibility of the LCD screen and reduce
eyestrain.

■ Position the computer so that sunlight or bright indoor lighting does not

reflect off the LCD screen. Use tinted windows, shades or other screen
to eliminate sun glare.

■ Avoid placing the computer in front of bright light that could shine

directly in your eyes.

■ If possible, use soft, indirect lighting in your computer work area. Use a

lamp to illuminate your documents or desk, but be sure to position the
lamp so that it does not reflect off the LCD screen or shine in your eyes.

User’s Manual 3-3

Getting Started

Work habits

A key to avoiding discomfort or injury from repetitive strain is to vary your
activities. If possible, schedule a variety of tasks into your workday. If you
must spend long periods at the computer, finding ways to break up the
routine can reduce stress and improve your efficiency.

■ Sit in a relaxed posture. Good positioning of your chair and equipment

as described earlier can reduce tension in your shoulders or neck and
ease back strain.

■ Vary your posture frequently.

■ Occasionally stand up and stretch or exercise briefly.

■ Exercise and stretch your wrists and hands a number of times during

the day.

■ Frequently, look away from the computer and focus your eyes on a

distant object for several seconds, for example 30 seconds every
15 minutes.

■ Take frequent short breaks instead of one or two long breaks,

for example, two or three minutes every half hour.

■ Have your eyes examined regularly and visit a doctor promptly,

if you suspect you might be suffering from a repetitive strain injury.

A number of books are available on ergonomics and repetitive strain injury
or repetitive stress syndrome. For more information on these topics or for
pointers on exercises for such stress points as hands and wrists, please
check with your library or book vendor. Also refer to the computer’s

Instruction Manual for Safety & Comfort.

Connecting the AC adaptor

Attach the AC adaptor when you need to charge the battery or you want to
operate from AC power. It is also the fastest way to get started, because
the battery pack will need to be charged before you can operate from
battery power.

The AC adaptor can be connected to any power source supplying from
100 to 240 volts and 50 or 60 hertz. For details on using the AC adaptor to
charge the battery pack, refer to Chapter 6, Power and Power-Up Modes.

Use only the AC adaptor supplied as an accessory. Other AC adaptors
have different voltage and terminal polarities and use of them may produce
heat and smoke or even result in fire or rupture.

3-4 User’s Manual

Getting Started

■ Use only the AC adaptor supplied with your computer or an equivalent

adaptor that is compatible. Use of any incompatible adaptor could
damage your computer. TOSHIBA assumes no liability for any damage
caused by use of an incompatible adaptor.

■ The supplied power cord conforms to safety rules and regulations in

the region the product is bought and should not be used outside this
region. For use in other regions, please buy power cords that conform
to safety rules and regulations in the particular region.

■ Do not use a 3-pin to 2-pin conversion plug.

■ When you connect the AC adaptor to the computer, always follow the

steps in the exact order as described in the User’s Manual. Connecting
the power cable to a live electrical outlet should be the last step
otherwise the adaptor DC output plug could hold an electrical change
and cause an electrical shock or minor bodily injury when touched.
As a general safety precaution, avoid touching any metal parts.

1. Connect the power cord to the AC adaptor.

Connecting the power cord to the AC adaptor (2-pin plug)

Connecting the power cord to the AC adaptor (3-pin plug)

The Universal AC Adaptor and power cord bundled with this product
may differ depending on the product model. Depending on the model,
a 2-pin plug or 3-pin plug set of the above may be bundled.

User’s Manual 3-5

Getting Started

2. Connect the AC adaptor’s DC output plug to the DC IN 15V jack on the
back of the computer.

Connecting the adaptor to the computer

3. Plug the power cord into a live wall outlet. The Battery and DC IN
indicators on the front of the computer should glow.

Opening the display

The computer’s LCD display panel can be rotated in a wide range of angles
for optimal viewing.

1. Push the display latch on the front of the computer to unlatch the
display panel.

2. While holding down the palm rest with one hand so that the main body
is not raised, lift the panel slowly. Adjust the angle of the panel to
provide optimal clarity.

DC IN 15V jack

Use reasonable care when opening and closing the LCD display panel.
Opening it vigorously or slamming it shut could damage the computer.

LCD display panel

Display latch

Opening the LCD display panel

3-6 User’s Manual

Turning on the power

This section describes how to turn on the power.
The Power button LED indicates the status. Refer to the Power indicators

section in Chapter 6, Power and Power-Up Modes.

■ After you turn on the power for the first time, do not turn it off until you

have set up the operating system. Refer to the section Starting up for

the first time.

■ If the USB floppy disk drive is connected, make sure it is empty. If a

floppy disk is in the drive, press the eject button and remove the floppy
disk.

1. Open the computer’s LCD display panel.

2. Press and hold the computer’s power button for two or three seconds.

Power buttonPower button

Getting Started

Turning on the power

Starting up for the first time

When you first turn on the power, the computer’s initial screen is the
Microsoft Windows XP Startup Screen Logo. Follow the on-screen
directions for each screen. During setup, you can click the Back button to
return to the previous screen.

Be sure to read the Windows End User License Agreement display
carefully.

Be sure to read the License Agreement carefully.

User’s Manual 3-7

Getting Started

Turning off the power

The power can be turned off in one of the following modes:
Shut down (Boot), Hibernation or Standby mode.

Shut Down mode (Boot mode)

When you turn off the power in Shut Down mode no data is saved and the
computer will boot to the operating system’s main screen.

1. If you have entered data, save it to the hard disk or to a floppy disk.

2. Make sure all disk (disc) activity has stopped, then remove the
CD/DVDs or floppy disk.

Make sure the HDD and Ultra Slim Bay’s module indicators are off.
If you turn off the power while a disk (disc) is being accessed, you can
lose data or damage the disk (disc).

3. Click start then click Turn Off Computer. From the Turn Off
Computer menu select Turn Off.

4. Turn off the power to any peripheral devices.

Do not turn the computer or devices back on immediately. Wait a moment
to let all capacitors fully discharge.

Hibernation mode

The hibernation feature saves the contents of memory to the hard disk
when the computer is turned off. The next time the computer is turned on,
the previous state is restored. The hibernation feature does not save the
status of peripheral devices.

■ Save your data. While entering hibernation mode, the computer saves

the contents of memory to the HDD. However, for safety sake, it is best
to save your data manually.

■ Data will be lost if you remove the battery or disconnect the AC adaptor

before the save is completed. Wait for the HDD indicator to go out.

■ Do not install or remove a memory module while the computer is in

hibernation mode. Data will be lost.

3-8 User’s Manual

Getting Started

Benefits of hibernation

The hibernation feature provides the following benefits:

■ Saves data to the hard disk when the computer automatically shuts

down because of a low battery.

For the computer to shut down in hibernation mode, the hibernation feature
must be enabled in two places: the Hibernate tab in Power Options and
Setup Action tab in TOSHIBA Power Saver.

Otherwise, the computer will shut down in Standby mode. If battery power
becomes depleted, data saved in Standby mode will be lost.

■ You can return to your previous working environment immediately when

you turn on the computer.

■ Saves power by shutting down the system when the computer receives

no input or hardware access for the duration set by the System
hibernate feature.

■ You can use the panel power off feature.

Starting Hibernation

You can also enable Hibernation by pressing Fn + F4. Refer to Chapter 5,

The Keyboard, for details.

To enter Hibernation mode, follow the steps below.

1. Click start.

2. Select Turn Off Computer.

3. Open the Turn Off Computer dialog box. Hibernate is not displayed.

4. Press the Shift key. The Standby item will change to Hibernate.

5. Select the Hibernate.

Automatic Hibernation

The computer will enter Hibernate mode automatically when you press the
power button or close the lid. First, however, make the appropriate settings
according to the steps below.

1. Click start and open the Control Panel.

2. Open Performance and Maintenance and open Power Options.

3. Select the Hibernate window in the Power Options Properties,

select the Enable hibernation check box and click the Apply button.

4. Open TOSHIBA Power Saver.

5. Select the Setup Action window.

6. Enable the desired Hibernation settings for When I press the power

button and When I close the lid.

7. Click the OK button.

User’s Manual 3-9

Getting Started

Standby mode

Data save in hibernation mode

When you turn off the power in hibernation mode, the computer takes a
moment to save current memory data to the hard disk. During this time,
the HDD indicator will light.

After you turn off the computer and memory is saved to the hard disk,
turn off the power to any peripheral devices.

Do not turn the computer or devices back on immediately. Wait a moment
to let all capacitors fully discharge.

If you have to interrupt your work, you can turn off the power without exiting
from your software. Data is maintained in the computer’s main memory.
When you turn on the power again, you can continue working right where
you left off.

■ When the AC adaptor is connected, the computer will go into Standby

mode according to the settings in the TOSHIBA Power Saver utility.

■ To restore operation from Standby mode, press the power button or

press any key. The latter action works only if Wake-up on Keyboard is
enabled in HW Setup.

■ If the computer automatically enters Standby mode while a network

application is active, the application might not be restored when the
computer wakes up from Standby.

■ To prevent the computer from automatically entering Standby mode,

disable Standby in TOSHIBA Power Saver. That action, however,
will nullify the computer’s Energy Star compliance.

■ Before entering Standby mode, be sure to save your data.

■ Do not install or remove a memory module while the computer is in

standby mode. The computer or the module could be damaged.

■ Do not remove the battery pack while the computer is in standby mode

(unless the computer is connected to an AC power source). Data in
memory will be lost.

■ If you carry the computer on board an aircraft or into a hospital, be sure

to shut down the computer in hibernation mode or in shutdown mode to
avoid radio signal interference.

Benefits of standby

The standby feature provides the following benefits:

■ Restores the previous working environment more rapidly than does

hibernation.

■ Saves power by shutting down the system when the computer receives

no input or hardware access for the duration set by the System Standby
feature.

■ You can use the panel power off feature.

3-10 User’s Manual

Getting Started

Executing standby

You can also enable Standby by pressing Fn + F3. See Chapter 5, The

Keyboard, for details.

You can enter standby mode in one of three ways:

1. Click start, click Turn Off Computer and click Stand By.

2. Close the computer’s LCD display panel. This feature must be enabled.

Refer to the Setup Action tab in TOSHIBA Power Saver Utility
described in the Control Panel.
Open Performance and Maintenance and open TOSHIBA Power

Saver.

3. Press the power button. This feature must be enabled. Refer to the

Setup Action tab in TOSHIBA Power Saver Utility described in the
Control Panel.
Open Performance and Maintenance and open TOSHIBA Power

Saver.

When you turn the power back on, you can continue where you left when
you shut down the computer.

■ When the computer is shut down in standby mode, the power indicator

blinking orange.

■ If you are operating the computer on battery power, you can lengthen

the operating time by shutting down in hibernation mode. Standby
mode consumes more power.

Standby limitations

Standby will not function under the following conditions:

■ Power is turned back on immediately after shutting down.

■ Memory circuits are exposed to static electricity or electrical noise.

Restarting the computer

Certain conditions require that you reset the system. For example, if:

■ You change certain computer settings.

■ An error occurs and the computer does not respond to your keyboard

commands.

■ There are three ways to reset the computer system:

1. Click start then click Turn off computer. From the Turn off

computer menu select Restart.

2. Press Ctrl + Alt + Del to display the Windows Task Manager,

then select Shut Down and Restart.

3. Press the power button and hold it down for five seconds. Wait 10 to

15 seconds, then turn the power on again by pressing the power button.

User’s Manual 3-11

Getting Started

Restoring the preinstalled software

Restoring the complete system

To restore the operating system and all preinstalled software, follow the
steps below.

When sound mute is turned ON by the Fn + Esc key, turn OFF before
starting restore. Refer to Chapter 5, The Keyboard, for details.

When you reinstall the Windows operating system, the hard disk will be
reformatted and all data will be lost.

1. Load the Product Recovery DVD-ROM in the optical media drive and
turn off the computer’s power.

2. Hold down the F12 key and turn on the power. When In Touch with
Tomorrow TOSHIBA appears, release the F12 key.

3. Use the left or right cursor key to select the CD-ROM icon in the
displayed menu. For details, refer to the Boot Priority section in Chapter
7, HW Setup.

4. Follow the on-screen instructions.

5. If your computer came with additional software installed, this software
can not be recovered from the Product Recovery DVD-ROM. Re-install
these applications (e.g. Works Suite, DVD Player, Games, etc.)
separately from other media.

Restoring TOSHIBA utilities and drivers

If Windows is working properly, individual drivers or applications can be
separately restored. The TOSHIBA Tools & Utilities folder (C:\TOOLSCD)
contains drivers and applications, which are included with your computer
system. If your system drivers or applications have become damaged in
some way, you can reinstall most of the components from this folder.

Create a copy of this folder to an external media for more convenience.

3-12 User’s Manual

PORTÉGÉ S100

Operating Basics

This chapter gives information on basic operations including using the
Touch Pad, USB floppy disk drive (optional), changing Ultra Slim Bay
modules, optical media drives, Sound System, Modem, Wireless
communication features and LAN. It also provides tips on caring for your
computer, floppy disks and CD/DVDs.

Using the Touch Pad

To use the Touch Pad, simply touch and move your fingertip across it in the
direction you want the on-screen pointer to go.

Chapter 4

Touch Pad

Touch Pad control
buttons

Touch Pad and Touch Pad control buttons

Two buttons below the Touch Pad are used like the buttons on a mouse
pointer. Press the left button to select a menu item or to manipulate text or
graphics designated by the pointer. Press the right button to display a menu
or other function depending on the software you are using.

You can also tap the Touch Pad to perform functions similar to those of the
left button.

Click: Tap on ce
Double-click: Tap twice
Drag and drop: Tap to select the material you want to move.

Leave your finger on the Touch Pad after the second tap and move the
material.

User’s Manual 4-1

Operating Basics

Using the USB floppy disk drive (optional)

USB floppy disk drive connects to the computer’s USB port.
It accommodates 1.44-megabyte or 720-kilobyte floppy disks.
Refer to Chapter 2, The Grand Tour, for more information.

Option or provided with some models.

Connecting USB floppy disk drive

To connect the drive, plug the floppy disk drive’s USB connector into a
computer’s USB port.

Make sure the connector is back side up and properly aligned with the
socket. Do not try to force the connection, doing so can damage the
connecting pins.

USB connector

USB port

Connecting the USB floppy disk drive

If you connect the USB floppy disk drive after turning on the computer,
it will take about 10 seconds for the computer to recognize the drive.
Do not disconnect and reconnect before 10 seconds has elapsed.

Disconnecting USB floppy disk drive

When you have finished using the USB floppy disk drive, follow the
procedures below to disconnect it:

1. Wait for the indicator light to go out to make sure all floppy disk activity
has stopped.

If you disconnect the USB floppy disk drive or turn off the power while the
computer is accessing the drive you may lose data or damage the floppy
disk or the drive.

2. Click the Safely Remove Hardware icon on the Task Bar.

3. Click USB floppy disk drive that you want remove.

4. Pull the floppy disk drive’s USB connector out of the computer’s USB
port.

4-2 User’s Manual

Changing Ultra Slim Bay modules

This section explains how to change modules in the Ultra Slim Bay.
The illustrations show replacement of the optical media drive with the
Ultra Slim Bay HDD adaptor. Therefore, the text refers to those modules.
However, the procedures are the same for any of the modules:
DVD-ROM&CD-R/RW drive, DVD Super Multi drive, HDD adaptor and
Ultra Slim Bay weight saver.

To avoid injury, do not put your hand into the Ultra Slim Bay slot.

The TOSHIBA Mobile Extension is preinstalled to support hot swapping
under Windows. Refer to Chapter 1, Introduction, for information on using
this utility to change modules while the computer’s power is on.

Removing a module

Remove the optical media drive as described below.

1. You can confirm that the disks are not operating with indicators.

If all indicators are off, it means that no disks are operating currently.

2. Turn the computer upside down.

Wait for all disk indicators to go out before you turn over the computer and
do not lay the computer down gently. Shock can damage the HDD or other
components.

Operating Basics

3. Remove the screw near the icon securing the Ultra Slim Bay.

4. Make sure the screw in the Ultra Slim Bay lock is set in the hole for the

unlock position.

5. Slide the Ultra Slim Bay latch to the unlock position.

User’s Manual 4-3

Operating Basics

6. Grasp the optical media drive and slide it out.

■ The optical media drive and other Ultra Slim Bay modules can become

■ Store the DVD Super Multi drive unit in the Ultra Slim Bay Case when

Inserting a module

Insert the Ultra Slim Bay HDD adaptor as described below.

1. Insert the Ultra Slim Bay HDD adaptor in the computer as shown below

2. If you want to lock the Ultra Slim Bay HDD adaptor, set the Ultra Slim

hot with use. Be careful when removing the module.

removing it from the computer or transporting it.

Lock screw

Ultra Slim
Bay latch

Optical media drive

Removing the optical media drive

and press until the ejector clicks.

Bay lock screw in the hole for the lock position (➁). The lock screw is
inserted in the unlock position (➀) at the time of purchasing.

Lock screw

Ultra Slim Bay
HDD adaptor

Inserting the Ultra Slim Bay HDD adaptor

4-4 User’s Manual

Using optical media drives

The full-size drive provides high-performance execution of CD/DVD-ROM­based programs. You can run either 12 cm (4.72") or 8 cm (3.15")
CD/DVDs without an adaptor. An ATAPI interface controller is used for
CD/DVD-ROM operation. When the computer is accessing a
CD/DVD-ROM, an indicator on the drive glows and the Ultra Slim Bay
indicator glows.

Use the WinDVD application to view DVD-Video discs.

If you have a DVD-ROM&CD-R/RW drive, refer also to the Writing CDs on

DVD-ROM&CD-R/RW drive section for precautions on writing to CDs.

If you have a DVD Super Multi drive, refer also to the Writing CD/DVDs on

DVD Super Multi drive section for precautions on writing to CDs.

When the power of the optical media drive is off, pressing the Fn + Tab
keys will turn the power of the optical media drive on. Furthermore,
it is possible to set it to turn the power of the optical media drive on and
eject the tray at the same time.

Loading discs

To load CD/DVDs, follow the steps below.

1. When the computer’s power is on, press the eject button to open the

disc tray slightly.

Operating Basics

Eject Button

Pressing the eject button

User’s Manual 4-5

Operating Basics

2. Grasp the disc tray gently and pull until it is fully opened.

Disc tray

Pulling the disc tray open

3. Lay the CD/DVD, label side up, in the disc tray.

Laser lens

Inserting a CD/DVD

When the disc tray is fully opened, the edge of the computer will extend
slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD
at an angle when you place it in the disc tray. After seating the CD/DVD,
however, make sure it lies flat.

■ Do not touch a laser lens and its circumference portion. Doing so could

cause misalignment.

■ Prevent foreign objects from entering the drive. Check the surface of

the disc tray, especially the area behind the front edge of the disc tray,
to make sure there are no such objects before closing the drive.

4. Press gently at the center of the CD/DVD until you feel it click into
place. The CD/DVD should lie below the top of the spindle,
flush with the spindle base.

4-6 User’s Manual

5. Push the center of the disc tray to close it. Press gently until it locks into

place.

If the CD/DVD is not seated properly when the disc tray is closed,
the CD/DVD might be damaged. Also, the disc tray might not open fully
when you press the eject button.

Closing the CD/DVD disc tray

Removing discs

To remove the CD/DVD, follow the steps below.

Do not press the eject button while the computer is accessing the media
drive. Wait for the Ultra Slim Bay indicator to go out before you open the
disc tray. Also, if the CD/DVD is spinning when you open the disc tray,
wait for it to stop before you remove it

.

Operating Basics

1. To pop the disc tray partially open, press the eject button. Gently pull

the disc tray out until it is fully opened.

When the disc tray pops open slightly, wait a moment to make sure the
CD/DVD has stopped spinning before pulling the disc tray fully open.

2. The CD/DVD extends slightly over the sides of the disc tray so you can

hold it. Hold the CD/DVD gently and lift it out.

Removing a CD/DVD

3. Push the center of the disc tray to close it. Press gently until it locks into

place.

User’s Manual 4-7

Operating Basics

How to remove CD/DVD when the disk tray will not open

Pressing the eject button will not open the disc tray when the computer
power is off. If the power is off, you can open the disc tray by inserting a
slender object (about 15 mm) such as a straightened paper clip into the
eject hole just to the right of the eject button.

Manual release with the eject hole

Turn off the power before you use the eject hole. If the CD/DVD is spinning
when you open the disc tray, the CD/DVD could fly off the spindle and
cause injury.

Writing CDs on DVD-ROM&CD-R/RW drive

Eject hole

Depending on the type of drive installed, you may be able to write CDs.
The DVD-ROM&CD-R/RW drive lets you write as well as read CD-ROMs.
Observe the precautions in this section to ensure the best performance for
writing CDs. For information on loading and unloading CDs refer to the

Using optical media drives section.

■ CD-R discs can be written to only once. CD-RW discs can be rewritten

many times.

■ When the power of the optical media drive is off, the disc tray will not

open even if the eject button is pushed. Use the optical media drive
power icon to turn the power of the optical media drive on. Refer to
Chapter 1, Special features.

■ Do not turn off the power of the optical media drive while the computer

is accessing the drive. If you turn off the power, you may lose data.

4-8 User’s Manual

Before writing or rewriting

Please observe the following points when you write or rewrite the data.

■ We recommend the following manufacturers of CD-R and CD-RW

media. Media quality can affect write or rewrite success rates.

CD-R:

TAIYO YUDEN CO., LTD.
MITSUBISHI CHEMICAL CORPORATION
RICOH Co., Ltd.
Hitachi Maxell Ltd.

Multi-Speed and High-Speed CD-RW:

MITSUBISHI CHEMICAL CORPORATION
RICOH Co., Ltd.

Ultra-Speed CD-RW:

MITSUBISHI CHEMICAL CORPORATION

TOSHIBA has confirmed the operation of CD-R and CD-RW media of the
manufacturers above. Operation of other media cannot be guaranteed.

■ The actual number of rewrites to CD-RW is affected by the quality of the

disc and the way it is used.

■ Be sure to connect the AC adaptor when you write or rewrite.

■ Be sure to close all other software programs except the writing

software.

■ Do not run software such as a screen saver which can put a heavy load

on the CPU.

■ Operate the computer at full power. Do not use power-saving features.

■ Do not write while virus check software is running. Wait for it to finish,

then disable virus detection programs including any software that
checks files automatically in the background.

■ Do not use hard disk utilities, including those intended to enhance HDD

access speed. They may cause unstable operation and damage data.

■ Write from the computer's HDD to the CD. Do not try to write from

shared devices such as a LAN server or any other network device.

■ Writing with software other than Sonic RecordNow! has not been

confirmed. Therefore, operation with other software cannot be
guaranteed.

Operating Basics

User’s Manual 4-9

Operating Basics

When writing or rewriting

Note the following when you write or rewrite a CD-R or CD-RW.

■ Always copy data from the HDD to the CD. Do not use cut-and-paste.

The original data will be lost if there is a write error.

■ Do not perform any of the following actions:

■ Change users in the Windows XP operating system.

■ Operate the computer for any other function, including use of a

mouse or Touch Pad, closing/opening the LCD panel.

■ Start a communication application such as a modem.

■ Apply impact or vibration to the computer.

■ Install, remove or connect external devices, including the following:

PC card, SD card, USB devices, external monitor, i.LINK devices,
optical digital devices.

■ Open the optical media drive.

■ Remove the optical media drive from the Ultra Slim Bay.

■ If the media is poor in quality, dirty or damaged, writing or rewriting

errors may occur.

■ Set the computer on a level surface and avoid places subject to

vibration such as airplanes, trains or cars. Do not use an unstable
surface such as a stand.

■ Keep mobile phones and other wireless communication devices away

from the computer.

Writing CD/DVDs on DVD Super Multi drive

You can use the DVD Super Multi drive to write data to either CD-R/RW or
DVD-R/-RW/+R/+RW/-RAM discs. The following applications for writing are
preinstalled: RecordNow!, and DLA licensed by Sonic Solutions.

■ CD-R discs can be written to only once. CD-RW discs can be rewritten

many times.

■ When the power of the optical media drive is off, the disc tray will not

open even if the eject button is pushed. Use the optical media drive
power icon to turn the power of the optical media drive on. Refer to
Chapter 1, Special features.

■ Do not turn off the power of the optical media drive while the computer

is accessing the drive. If you turn off the power, you may lose data.

Important message

Before you write or rewrite to CD-R/RW or DVD-R/-RW/+R/+RW/-RAM
disc, read and follow all setup and operating instructions in this section.
If you fail to do so, the DVD Super Multi drive may not function properly,
and you may fail to write or rewrite, lose data or incur other damage.

4-10 User’s Manual

Disclaimer

TOSHIBA does not bear responsibility for the following:

■ Damage to any CD-R/RW or DVD-R/-RW/+R/+RW/-RAM disc that may

be caused by writing or rewriting with this product.

■ Any change or loss of the recorded contents of CD-R/RW or

DVD-R/-RW/+R/+RW/-RAM disc that may be caused by writing or
rewriting with this product, or for any business profit loss or business
interruption that may be caused by the change or loss of the recorded
contents.

■ Damage that may be caused by using third party equipment or

software.

Given the technological limitations of current optical disc writing drives,
you may experience unexpected writing or rewriting errors due to disc
quality or problems with hardware devices. Also, it is a good idea to make
two or more copies of important data, in case of undesired change or loss
of the recorded contents.

Before writing or rewriting

■ Based on TOSHIBA's limited compatibility testing, we suggest the

following manufacturers of CD-R/RW and DVD-R/+R/-RW/+RW/-RAM
disc. However, in no event does TOSHIBA guarantee the operation,
quality or performance of any disc. Disc quality can affect write or
rewrite success rates.

Operating Basics

CD-R:

TAIYO YUDEN CO., LTD.
MITSUBISHI CHEMICAL CORPORATION
RICOH Co., Ltd.
Hitachi Maxell Ltd.

CD-RW: (Multi-Speed and High-Speed)

MITSUBISHI CHEMICAL CORPORATION
RICOH Co., Ltd.

CD-RW: (Ultra-Speed)

MITSUBISHI CHEMICAL CORPORATION

DVD-R:

DVD Specifications for Recordable Disc for General Version 2.0

TAIYO YUDEN CO., LTD.
Matsushita Electric Industrial Co., Ltd.

DVD+R:

MITSUBISHI CHEMICAL CORPORATION
RICOH Co., Ltd.

User’s Manual 4-11

Operating Basics

DVD-RW:

DVD Specifications for Recordable Disc for Version 1.1 or
version 1.2

VICTOR COMPANY OF JAPAN.LIMITED
MITSUBISHI CHEMICAL CORPORATION

DVD+RW:

MITSUBISHI CHEMICAL CORPORATION
RICOH Co., Ltd.

DVD-RAM:

DVD Specifications for DVD-RAM Disc for Version 2.0 or
Version 2.1

Matsushita Electric Industrial Co., Ltd.
Hitachi Maxell Ltd.

This drive cannot use discs that allow writing faster than 8 speed
(DVD-R,DVD+R), 4 speed (DVD-RW, DVD+RW), 3 speed (DVD-RAM).

■ If the disc is poor in quality, dirty or damaged, writing or rewriting errors

may occur. Be careful to check the disc for dirt or damage before you
use it.

■ The actual number of rewrites to CD-RW, DVD-RW, DVD+RW or

DVD-RAM is affected by the quality of the disc and the way it is used.

■ There are two types of DVD-R discs: authoring and general use discs.

Do not use authoring discs. Only general use discs can be written to by
a computer drive.

■ You can use DVD-RAM discs that can be removed from a cartridge and

DVD-RAM discs designed without a cartridge. You cannot use a disc
with a 4.7 GB single-sided capacity or 9.4 GB double-sided capacity.

■ Other DVD-ROM drives for computers or other DVD players may not be

able to read DVD-R/-RW or DVD+R/+RW discs.

■ Data written to a CD-R/DVD-R/DVD+R disc cannot be deleted either in

whole or in part.

■ Data deleted (erased) from a CD-RW, DVD-RW, DVD+RW and

DVD-RAM disc cannot be recovered. Check the content of the disc
carefully before you delete it. If multiple drives that can write data to
discs are connected, be careful not to delete data from the wrong drive.

■ In writing to a DVD-R/-RW, DVD+R/+RW or DVD-RAM disc, some disc

space is required for file management, so you may not be able to write
the full capacity of the disc.

■ Since the disc is based on the DVD standard, it might be filled with

dummy data if the written data is less than about 1 GB. Even if you write
only a small amount of data, it might take time to fill in the dummy data.

■ DVD-RAM formatted by FAT32 cannot be read in Windows 2000

without DVD-RAM Driver Software.

4-12 User’s Manual

■ When multiple drives that can write data to discs are connected,

be careful not to write to the wrong drive.

■ Be sure to connect the AC adaptor before you write or rewrite.

■ Before you enter standby/hibernation mode, be sure to finish DVD-RAM

writing. Writing is finished if you can eject DVD-RAM media.

■ Be sure to close all other software programs except the writing

software.

■ Do not run software such as a screen saver, which can put a heavy load

on the CPU.

■ Operate the computer in the full-power mode. Do not use power-saving

features.

■ Do not write while virus check software is running. Wait for it to finish

and then disable virus detection programs including any software that
checks files automatically in the background.

■ Do not use hard disk utilities, including those intended to enhance HDD

access speed. They may cause unstable operation and data damage.

■ CD-RW (Ultra Speed +) media is not available. If used, data may be lost

or damaged.

■ Write from the computer’s HDD to the CD/DVD. Do not try to write from

shared devices such as a LAN server or any other network device.

■ Writing with software other than RecordNow! and InterVideo WinDVD

Creator Platinum are not recommended.

When writing or rewriting

Please observe/consider the following when you write or rewrite to a
CD-R/RW, DVD-R/-RW/-RAM or DVD+R/+RW disc.

■ Do not perform any of the following actions when writing or rewriting:

■ Change users in the Windows XP operating system.

■ Operate the computer for any other function, including using a

mouse or Touch Pad or closing/opening the LCD panel.

■ Start a communication application such as a modem.

■ Apply impact or vibration to the computer.

■ Install, remove or connect external devices, including the following:

PC card, SD card, USB devices, external monitor, i.LINK devices,
optical digital devices.

■ Use the Audio/Video control button to reproduce music or voice.

■ Open the optical media drive.

■ Remove the optical media drive from the Ultra Slim Bay.

■ Do not use shut down/log off and standby/hibernation while writing or

rewriting.

■ Make sure writing or rewriting is completed before going into

standby/hibernation. Writing is completed if you can open the
DVD-ROM&CD-R/RW or DVD Super Multi drive tray.

Operating Basics

User’s Manual 4-13

Operating Basics

■ Set the computer on a level surface and avoid places subject to

vibration such as airplanes, trains, or cars. Do not use an unstable
surface such as a stand.

■ Keep mobile phones and other wireless communication devices away

from the computer.

■ Always copy data from the HDD to the DVD-RAM. Do not use

cut-and-paste. The original data will be lost if there is a write error.

RecordNow! Basic for TOSHIBA

Note the following limitations when you use RecordNow!:

■ DVD-Video cannot be created using RecordNow!.

■ DVD-Audio cannot be created using RecordNow!.

■ You cannot use RecordNow!'s “Audio CD for Car or Home CD Player”

function to record music to the DVD-R/-RW or DVD+R/+RW disc.

■ Do not use the “Exact Copy” function of RecordNow! to copy

DVD-Video and DVD-ROM with copyright protection.

■ DVD-RAM disc cannot be backed up with the “Exact Copy” function of

RecordNow!.

■ You cannot back up a CD-ROM or CD-R/RW to DVD-R/-RW or

DVD+R/+RW using the “Exact Copy” function of RecordNow!.

■ You cannot back up DVD-ROM, DVD-Video or DVD-R/-RW or

DVD+R/+RW to CD-R/RW using the “Exact Copy” function of
RecordNow!.

■ RecordNow! cannot record in packet format.

■ You might not be able to use the “Exact Copy” function of RecordNow!

to back up a DVD-R/-RW or DVD+R/+RW disc that was made with
other software on a different DVD-R/-RW or DVD+R/+RW recorder.

■ If you add data to a DVD-R and DVD+R disc that you have already

recorded to, you might not be able to read the added data under some
circumstances. It cannot be read in 16-bit operating systems, such as
Windows 98SE and Windows Me. In Windows NT4, you will need
Service Pack 6 or later to read added data. In Windows 2000, you will
need Service Pack 2 or later to read it. Some DVD-ROM and
DVD-ROM&CD-R/RW drives cannot read added data regardless of the
operating system.

■ RecordNow! does not support recording to DVD-RAM discs.

To record to a DVD-RAM, use Explorer or other utility.

■ When you back up a DVD disc, be sure the source drive supports

recording to DVD-R/-RW or DVD+R/+RW discs. If the source drive
does not support recording to DVD-R/-RW or DVD+R/+RW discs,
it might not be backed up correctly.

■ When you back up a DVD-R, DVD-RW, DVD+R or DVD+RW, be sure to

use the same type of disc.

■ You cannot partially delete any data written to a CD-RW, DVD-RW or

DVD+RW disc.

4-14 User’s Manual

Data Verification

To verify that data is written or rewritten correctly, follow the steps below
before you write or rewrite a Data CD/DVD.

1. Click the Options button ( ) on the RecordNow! Console to open the

Options panels.

2. Select the Data in the left-side menu.

3. Mark the Verify data written to the disc after burning check box in the

Data Options.

Click the OK button.

DLA for TOSHIBA

Note the following limitations when you use DLA:

■ This software supports only rewritable discs (DVD+RW, DVD-RW,

and CD-RW). It does not support DVD+R, DVD-R, and CD-R discs that
are not rewritable.

■ DLA does not support formatting a DVD-RAM disc and writing to it.

They are performed by DVD-RAM Driver Software. If DLA Format
menu may appear when inserting a DVD-RAM disc into the drive
and right-clicking the drive icon in Windows Explorer, please use
“DVDForm” to format this disc. You can run “DVDForm” by clicking the
Start button on the taskbar to display the Start menu and then selecting
“All Programs”, “DVD-RAM”, “DVD-RAM Driver” and “DVDForm”
sequentially.

■ Do not use any discs that have been formatted with packet writing

software other than DLA. Similarly, do not use any discs that have been
formatted with DLA with any packet writing software other than DLA.
When using a disc you are not familiar with, format it by selecting
“Full Format” before using it.

■ Do not use the Cut & Paste function for files and folders. A file or folder

that has been cut may be lost if writing fails due to an error on the disc.

■ When writing the Setup files for the program to a disc formatted by DLA

and starting Setup from this disc, an error may occur. In this case,
please copy them to your hard disk and then run Setup.

Operating Basics

Video

As for InterVideo WinDVD Creator Platinum. Only the model that can be
written in to DVD is attached.

User’s Manual 4-15

Operating Basics

When using WinDVD Creator Platinum

You can record video back to your digital camcorder via i.LINK (IEEE1394)
using WinDVD Creator Platinum. However, there is a case where its
playback sound is choppy.

1. Click start and select the Control Panel.

2. Click the Performance and Maintenance icon in the Control Panel.

3. Click the System icon in the Performance and Maintenance window.

4. Click the Advanced tab in the System Properties window.

5. Click the Settings icon in the “Performance” section.

6. Click the Advanced tab in the Performance Options window.

7. Click the Change icon in the “virtual memory” section.

8. Select the Custom size button in the Virtual Memory window.

9. Specify much higher values for “Initial size” and “Maximum size.”

10. Click the Set button in the Virtual Memory window.

11. Click the OK button in the Virtual Memory window.

How to make a DVD-Video

Simplified steps for making a DVD-Video from video data captured from a
DV-Camcorder:

1. Click [Start]-[All Programs] - [InterVideo WinDVD Creator2] ­[InterVideo WinDVD Creator] to launch WinDVD Creator.

2. Click [Capture] button then capture the video data from the
DV-Camcorder via IEEE1394.

3. Click [Edit] button then drag the video clips from [Video Library] tab to
the edit track.

4. Click [Make Movie] button in the top bar.

5. Double Click the Right arrow button icon in the center of right side.

6. Put a blank DVD-R/+R disc or an erased DVD-RW/+RW disc in the
drive.

7. Click [Start] to record to the disc.

8. When recording is finished, the tray opens.

How to learn more about InterVideo WinDVD Creator

Please refer to the on-line Help for additional InterVideo WinDVD Creator
information.

4-16 User’s Manual

Important information for use

Note the following limitations when you write video DVD:

1. Editing digital video

■ Log in with Administrator rights to use WinDVD Creator.

■ Make sure that your computer is running on AC power when using

WinDVD Creator.

■ Operate the computer at Full Power. Do not use power-saving

features.

■ While you are editing DVD, you can display previews. However,

if another application is running, the preview might not display
properly.

■ WinDVD Creator cannot show video on the external monitor when in

simultaneous mode.

■ WinDVD Creator cannot edit or play copy protected content.

■ Do not change display settings while using WinDVD Creator.

■ Do not enter standby/hibernation mode while using WinDVD

Creator.

■ Do not operate WinDVD Creator immediately after turning on the

computer. Please wait until all Disc Drive activity has stopped.

■ When recording to a DV-Camcorder, to ensure you capture all of

your data, let the camcorder record for a few seconds before you
begin recording your actual data.

■ CD recorder, JPEG functions, DVD-Audio, mini DVD and Video CD

functions are not supported in this version.

■ While recording video to DVD or tape, please close all other

programs.

■ Do not run software like a screen saver because it can put a heavy

load on the CPU.

■ Do not run communication applications like a modem or a LAN.

2. Before recording the video to DVD

■ When you record to DVD disc, please use only discs recommended

by the Drive manufacturer.

■ Do not set the working drive to a slow device like a USB 1.1 hard

disk drive or it will fail to write DVD.

■ Do not perform any of the following actions:

■ Operate the computer for any other function, including using a

mouse or Touch Pad or closing/opening the LCD panel.

■ Bump or cause vibration to the computer.

■ Use the Mode control button and Audio/Video control button to

reproduce music or voice.

■ Open the DVD drive.

■ Install, remove or connect external devices, including the

following: PC card, SD card, USB devices, external monitor,
i.LINK devices, optical digital devices.

Operating Basics

User’s Manual 4-17

Operating Basics

■ Please verify your disc after recording important data.

■ DVD-R/+R/-RW disc cannot be written in VR format.

■ WinDVD Creator cannot export to DVD-Audio, VideoCD, miniDVD

format.

■ WinDVD Creator can write DVD-RAM/+RW in VR format, but the

disc may only play on your computer.

■ When writing to DVD disc, WinDVD Creator requires 2GB or more

over disk space every one hour of video.

■ When you make a fully recorded DVD, the chapter sequence may

not play correctly.

3. About Disc Manager

■ WinDVD Creator can edit one play list on a disc.

■ WinDVD Creator might show a different a thumbnail than you

previously set in CE (Consumer Electronics) DVD-RAM recorder.

■ Using the Disc Manager, you can edit DVD-VR format on

DVD-RAM, DVD+VR format on DVD+RW, and DVD-Video
format on DVD-RW.

4. About recorded DVDs

■ Some DVD-ROM drives for personal computers or other DVD

players may not be able to read DVD-R/+R/-RW/+RW/-RAM discs.

■ When playing your recorded disc on your computer, please use the

WinDVD software application.

■ If you use an over-used rewritable disc, the full formatting might be

locked. Please use a brand new disc.

Media care

This section provides tips on protecting data stored on your CD/DVDs and
floppy disks.

Handle your media with care. The following simple precautions will
increase the lifetime of your media and protect the data stored on them:

CD/DVDs

1. Store your CD/DVDs in the container they came in to protect them and
keep them clean.

2. Do not bend the CD/DVD.

3. Do not write on, apply a sticker to, or otherwise mar the surface of the
CD/DVD that contains data.

4. Hold the CD/DVD by its outside edge or the edge on the center hole.
Fingerprints on the surface can prevent the drive from properly reading
data.

5. Do not expose to direct sunlight, extreme heat or cold. Do not place
heavy objects on your CD/DVDs.

4-18 User’s Manual

6. If your CD/DVDs become dusty or dirty, wipe them with a clean dry

cloth. Wipe from the center out, do not wipe in a circular direction
around the CD/DVD. If necessary, use a cloth dampened in water or a
neutral cleaner. Do not use benzine, thinner or similar cleaner.

Floppy disks

1. Store your floppy disks in the container they came in to protect them

and keep them clean. If a floppy disk is dirty, do not use cleaning fluid.
Clean it with a soft damp cloth.

2. Do not slide back the floppy disk’s protective metal covering or touch

the floppy disk’s magnetic surface. Fingerprints may prevent the floppy
disk drive from reading data from the floppy disk.

3. Data may be lost if the floppy disk is twisted; bent; or exposed to direct

sunlight, extreme heat or cold.

4. Do not place heavy objects on your floppy disks.

5. Do not eat, smoke, or use erasers near your floppy disks. Foreign

particles inside the floppy disk’s jacket can damage the magnetic
surface.

6. Magnetic energy can destroy the data on your floppy disks. Keep your

floppy disks away from speakers, radios, television sets and other
sources of magnetic fields.

Sound System

Operating Basics

Using the microphone

Your computer has a built-in microphone that can be used to record
monaural sounds into your applications. It can also be used to issue voice
commands to applications that support such functions.

Since your computer has a built-in microphone and speaker, “howling” may
be heard under certain conditions. Howling occurs when sound from the
speaker is picked up in the microphone and amplified back to the speaker,
which amplifies it again to the microphone.

This howling occurs repeatedly and causes a very loud, high-pitched noise.
It is a common phenomenon that occurs in any sound system when the
microphone input is output to the speaker (throughput) and the speaker
volume is too loud or too close to the microphone. You can control
throughput by adjusting the volume of your speaker or through the Mute
function.

To adjust the volume or activate Mute, click start, point to All Programs,
point to Accessories, point to Entertainment and click Volume Control.
In the Volume Control panel, you can use the slide bars to adjust the
volume level or click Mute at the bottom of the panel.

User’s Manual 4-19

Operating Basics

SoundMAX control panel

The SoundMAX control panel lets you control additional functions for the
Microphone Enhancement and Audio Power Management. To launch the
SoundMAX Control Panel, follow the steps below.

1. Click start and click Control Panel.

2. If you are viewing the Control Panel in Category View, click on Switch
to Classic View.

3. Double-click the SoundMAX icon.

The Microphone Setup allows you to optimize the microphone input
settings for your particular configuration. Choose Standard Microphone if
you have an ordinary desktop microphone. Choose Headset if you have a
wearable microphone that is positioned directly in front of your mouth.

You can launch the Setup Wizard from the Control Panel to help you to
automatically set proper microphone input volumes and ensure that your
voice input(s) are working correctly. As you speak into the microphone,
the Sound Meter indicates the audio signal that your PC is receiving.

The Noise Reduction enhancement helps to eliminate ambient noise from
the voice input signal to provide a clean and clear signal to applications.
This feature can be used with any microphone.

The audio controller can be powered down when the audio function is idle.
To enable the Audio Power Management, follow the steps below.

1. Click the Power Management tab.

2. Select the Normal Power Savings in the Power Mode pull-down list.

If the No Power Savings is selected, the audio controller always runs.

If you want to a more effect for the power management, you can select
another mode, the High Power Savings which can save the power than
the Normal Power Savings. To select it, follow the steps below.

1. Click the Power Management tab.

2. Select the High Power Savings in the Power Mode pull-down list.

3. Input a time in Power Save Delay (Seconds).

If the High Power Saving is selected, you need to play an audio file once
before you use a microphone or play an audio CD by the analog CD audio.

Mic Effect

TOSHIBA Mic Effect provides you with a hands-free environment for
holding mutual communication via the Internet Protocol or Local Area
Network. If you wish to communicate with someone on your computer,
you can use a messenger application. However, with such an application,
you would hear your own voice returning to you as echo during the
communication if you did not use a headset system or headphone.
TOSHIBA Mic Effect will reduce these echoes generated on your computer.
Form more information on using the TOSHIBA Mic Effect, refer to its help.

4-20 User’s Manual

Modem

This section describes how to connect and disconnect the internal modem
to and from a telephone jack.

The internal modem does not support voice functions. All data and fax
functions are supported.

■ In case of a lightning storm, unplug the modular cable from the

■ Do not connect the modem to a digital telephone line. A digital line will

Region selection

Telecommunication regulations vary from one region to another, so you will
need to make sure the internal modem’s settings are correct for the region
in which it will be used.

To select a region, follow the steps below.

1. Click start, point to All Programs, point to TOSHIBA, point to

Do not use the Country/Region Select function in the Modem setup
utility in the Control Panel if the function is available. If you change the
Country/Region in the Control Panel, the change may not take effect.

Operating Basics

telephone jack.

damage the modem.

Networking and click Modem Region Select.

2. The Region Selection icon will appear in the Windows Task Bar.

3. Click the icon with the primary mouse button to display a list of regions

that the modem supports. A sub menu for telephony location
information will also be displayed. A check will appear next to the
currently selected region and telephony location.

4. Select a region from the region menu or a telephony location from the

sub-menu.

■ When you click a region it becomes the modem’s region selection,

and the New Location for telephony will be set automatically.

■ When you select a telephony location, the corresponding region is

automatically selected and it becomes the modem’s current region
setting.

Properties menu

Click the icon with the secondary mouse button to display properties menu
on the screen.

User’s Manual 4-21

Operating Basics

Setting

You can enable or disable the following settings:

AutoRun Mode

The Region Select utility starts automatically when you start up the
operating system.

Open the Dialing Properties dialog box after selecting region.

The dialing properties dialog box will be displayed automatically after you
select the region.

Location list for region selection.

A submenu appears displaying location information for telephony.

Open dialog box, if the modem and Telephony Current
Location region code do not match.

A warning dialog box is displayed if current settings for region code and
telephony location are incorrect.

Modem Selection

If the computer cannot recognize the internal modem, a dialog box is
displayed. Select the COM port for your modem to use.

Dialing Properties

Select this item to display the dialing properties.

If you are using the computer in Japan, the Telecommunications Business
Law requires that you select Japan region mode. It is illegal to use the
modem in Japan with any other selection.

Connecting

To connect the modular cable, follow the steps below.

The modular cable that comes with the computer must be used to connect
a modem. Connect the end of the modular cable with the core to the
computer.

■ In case of a lightning storm, unplug the modular cable from the

telephone jack.

■ Do not connect the modem to a digital telephone line.

A digital line will damage the modem.

4-22 User’s Manual

1. Plug one end of the modular cable into the computer’s modem jack.

2. Plug the other end of the modular cable into a telephone jack.

Modular cable

Telephone jack

Modem jack

Modem jack

Connecting the internal modem

Do not pull on the cable or move the computer while the cable is
connected.

If you use a storage device such as an optical drive or HDD connected to a
16-bit PC card, you might experience the following modem problems:

■ Modem speed is slow or communication is interrupted.

■ Skips may occur in sound.

Disconnecting

To disconnect the internal modular cable, follow the steps below.

1. Pinch the lever on the connector in the telephone jack and pull out the

connector.

2. Disconnect the cable from the computer’s modem jack in the same

manner.

Operating Basics

Wireless communications

The computer’s wireless communication function supports Wireless LAN.

Wireless LAN

The Wireless LAN is compatible with other LAN systems based on Direct
Sequence Spread Spectrum /Orthogonal Frequency Division Multiplexing
radio technology that complies with IEEE802.11 Wireless LAN standard
(Revision A, B or G).

■ Theoretical maximum speed: 54Mbps (IEEE802.11a, 802.11g)

■ Theoretical maximum speed: 11Mbps (IEEE802.11b)

■ Frequency Channel Selection (Revision A:5 GHz, Revision B/G:

2.4 GHz)

■ Roaming over multiple channels

■ Card Power Management

User’s Manual 4-23

Operating Basics

■ Wired Equivalent Privacy (WEP) data encryption, based on the 128 bit

encryption algorithm (Intel module type).

■ Wi-Fi Protected Access (WPA).

■ The numerical values for display are the theoretical maximums for

Wireless LAN standards. The actual values may differ.

■ The transmission speed over the wireless LAN and the distance over

which wireless LAN can reach may vary depending on surrounding
electromagnetic environment, obstacles, access point design and
configuration, and client design and software/hardware configurations.
The Transmit Rate (at X Mbit/s) is the theoretical maximum speed
under the IEEE802.11 (a/b/g) standard. The actual transmission speed
will be lower than the theoretical maximum speed.

Security

■ Be sure to enable WEP (encryption) function. Otherwise your computer

will allow the illegal access by outsider through Wireless LAN to cause
illegal intrusion, eavesdropping, and loss or destruction of stored data.
TOSHIBA strongly recommend the customer to enable the WEP
function.

■ TOSHIBA is not liable for the eavesdropping of data due to the use of

Wireless LAN and the damage thereof.

Wireless communication switch

You can enable or disable Wireless LAN function, with the on/off switch.
No transmissions are sent or received when the switch is off. Slide the
switch to the right to turn it on and to the left to turn it off.

■ Set the switch to off in airplanes and hospitals. Check the indicator.

It will stop glowing when the wireless communication function is off.

■ Turn the computer off when you enter an airplane and check the

carrier's regulations before you use a computer on board.

4-24 User’s Manual

Wireless communication Indicator

The wireless communication indicator indicates the status of the wireless
communication functions.

Indicator status Indication

Indicator off Wireless communication switch is set to off.

Automatic power down because of overheating.
Power malfunction

Operating Basics

If you used the Task Bar to disable W-LAN, restart the computer or follow
the procedures below to enable the system to recognize W-LAN. Open or
click the following: Start, Control Panel, System, Hardware Device

Manager, Network adapters, Intel
Network Connection and enable.

LAN

The computer has built-in support for Ethernet LAN (10 megabits per
second, 10BASE-T), Fast Ethernet LAN (100 megabits per second,
100BASE-TX) and Gigabit Ethernet LAN (1000 megabits per second,
1000BASE-T).
This section describes how to connect/disconnect to a LAN.

LAN cable types

Indicator glows Wireless communication switch is on. Wireless

Do not install or remove an optional memory module while Wake-up on
LAN is enabled.

The Wake-up on LAN function consumes power even when the system is
off. Leave the AC adaptor connected while using this feature.

The computer must be configured properly before connecting to a LAN.
Logging onto a LAN using the computer’s default settings could cause a
malfunction in LAN operation. Check with your LAN administrator
regarding set-up procedures.

LAN is turned on by an application.

®

PRO/Wireless 2200BG/2915ABG

If you are using Gigabit Ethernet LAN (1000 megabits per second,
1000BASE-T), be sure to connect with a CAT5E cable or higher.
You cannot use a CAT3 or CAT5 cable.

If you are using Fast Ethernet LAN (100 megabits per second,
100BASE-TX), be sure to connect with a CAT5 cable or higher.
You cannot use a CAT3 cable.

If you are using Ethernet LAN (10 megabits per second, 10BASE-T),
you can connect with a CAT3 or higher.

User’s Manual 4-25

Operating Basics

Connecting LAN cable

To connect the LAN cable, follow the steps below.

■ Connect the AC adaptor before connecting the LAN cable. The AC

adaptor must remain connected during LAN use. If you disconnect the
AC Adaptor while the computer is accessing a LAN, the system may
hang up.

■ Do not connect any other cable to the LAN jack except the LAN cable.

Otherwise, malfunctions or damage may occur.

■ Do not connect any power supplying device to the LAN cable that is

connected to the LAN jack. Otherwise, malfunctions or damage may
occur.

1. Turn off the power to the computer and to all external devices
connected to the computer.

2. Plug one end of the cable into the LAN jack. Press gently until you hear
the latch click into place.

LAN connector

LAN jack

Connecting the LAN cable

3. Plug the other end of the cable into a LAN hub connector.
Check with your LAN administrator before connecting to a hub.

When the computer is exchanging data with the LAN, the LAN Active
indicator glows orange. When the computer is connected to a LAN hub
but is not exchanging data, the Link indicator glows green.

Disconnecting LAN cable

To disconnect the LAN cable, follow the steps below.

Make sure the LAN Active indicator (orange LED) is out before you
disconnect the computer from the LAN.

1. Pinch the lever on the connector in the computer’s LAN jack and pull
out the connector.

2. Disconnect the cable from the LAN hub in the same manner.
Check with your LAN administrator before disconnecting from the hub.

4-26 User’s Manual

Cleaning the computer

To help ensure long, trouble-free operation, keep the computer free of dust
and use care with liquids around the computer.

■ Be careful not to spill liquids into the computer. If the computer does get

wet, turn the power off immediately and let the computer dry completely
before you turn it on again.

■ Clean the computer using a slightly damp (with water) cloth. You can

use glass cleaner on the LCD display screen. Spray a small amount of
cleaner on a soft, clean cloth and wipe the screen gently with the cloth.

Never spray cleaner directly onto the computer or let liquid run into any
part of it. Never use harsh or caustic chemical products to clean the
computer.

Moving the computer

The computer is designed for rugged durability. However, a few simple
precautions taken when moving the computer will help ensure trouble-free
operation.

■ Before moving the computer, it recommends changing the function of

HDD Protection. Refer to the section, Using the Hard Disk Drive (HDD)

Protection, in this chapter.

■ Make sure all disk activity has ended before moving the computer.

Check the HDD indicator on the computer.

■ If a CD/DVD is in the drives, remove it. Also make sure the disc tray is

securely closed.

■ Turn off the power to the computer.

■ Disconnect the AC adaptor and all peripherals before moving the

computer.

■ Close the LCD display panel. Do not pick up the computer by its panel.

■ Close all port covers.

■ Use the carrying case when transporting the computer.

■ When carrying your computer, be sure to hold it securely so that it does

not fall or hit anything.

■ Do not carry your computer by holding protruded portions.

Operating Basics

User’s Manual 4-27

Operating Basics

Using the Hard Disk Drive (HDD) Protection

There is a function for reducing the risk of damage on HDD in this
computer.

Using the acceleration sensor built in the computer, HDD Protection detects
vibration, shocks and similar signs in the computer, and automatically
moves the HDD head to a safe position in order to reduce the risk of
damage that could be caused by a head-to-disk contact.

This function does not guarantee that the HDD will not be damaged.

When vibration is detected, the following message is displayed, and the
icon in the notification area of the taskbar is changed to the protection
state. This message is displayed until the OK button is pressed or
30 seconds pass. When vibration subsides, the icon returns to the normal
state.

HDD Protection Message

Taskbar Icon

State Icon Description

Normal HDD Protection is enabled.

Protection HDD Protection is active.

The HDD head is at a safe position.

OFF HDD Protection is disabled.

4-28 User’s Manual

TOSHIBA HDD Protection Properties

You can make the HDD Protection settings by using the TOSHIBA HDD
Protection Properties window. To open the window, click start point to All

Programs point to TOSHIBA point to Utilities and click HDD Protection
setting. The window can also be started from the icon on the Taskbar,

or from the Control Panel.

Operating Basics

TOSHIBA HDD Protection Properties

HDD Protection

You can choose whether to enable or disable HDD Protection.

Detection Level

This function can be set to four levels. The sensitivity levels in which
vibrations, impacts and their similar signs are detected can be set to OFF,
1, 2, and 3 in ascending order. Level 3 is recommended for better
protection of the computer. However, when the computer is used as
handheld or in other unstable conditions, setting the detection level to 3
could result in frequent execution of HDD Protection, which will slow HDD
reading and writing. Set a lower detection level when the speed of HDD
reading and writing is a priority.

Different detection levels can be set depending on whether the computer is
used as handheld or mobile usages, or whether it is used in a stable
environment such as on a table in the workplace or at home. By setting
different detection levels for the computer depending on whether it runs
with the AC power (desktop) or with batteries (handheld or mobile usage),
the detection level automatically switches according to the power
connection mode.

User’s Manual 4-29

Operating Basics

Detail Properties

To open the Detail Properties window, click the Setup Detail button in the
TOSHIBA HDD Protection Properties window.

Detection Level Amplification

When the AC adaptor is disconnected or the lid is closed, HDD Detection
assumes that the computer will be carried and sets the detection level to
the maximum for 10 seconds.

HDD Protection Message

Specify whether to display a message when HDD Protection is active.

Detail Properties

■ This function does not work when the computer is starting, in standby,

in hibernation, in transition to hibernation, recovering from hibernation,
or powered off. Be sure to not subject the computer to vibration or
impact while the function is disabled.

■ This function supports only Windows® XP.

4-30 User’s Manual

Heat dispersal

To protect from overheating, the CPU has an internal temperature sensor.
If the computer’s internal temperature rises to a certain level, the cooling
fan is turned on or the processing speed is lowered. You can select
whether to control the CPU temperature by turning on the fan first, then if
necessary, lowering the CPU speed. Or, by lowering the CPU speed first,
then if necessary, turning on the fan. Use the Cooling Method item of the
Basic Setup tab in TOSHIBA Power Saver.

Operating Basics

Maximum

Performance

Performance Uses a combination of the fan and lowering the CPU

Battery

optimized

When the CPU temperature falls to a normal range, the fan is turned off
and the CPU operation returns to standard speed.

If the CPU temperature reaches an unacceptably high level with either
setting, the system automatically shuts down to prevent damage.
Data in memory will be lost.

Turns on the fan first, then if necessary, lowers the CPU
processing speed.

processing speed.

Lowers the CPU processing speed first, then if
necessary turns on the fan.

User’s Manual 4-31

Operating Basics

4-32 User’s Manual

PORTÉGÉ S100

The Keyboard

The computer’s keyboard layouts are compatible with a 101/102-key
enhanced keyboard. By pressing some keys in combination, all the
101/102-key keyboard functions can be executed on the computer.

The number of keys on your keyboard depends on which country/region’s
keyboard layout your computer is configured with. Keyboards for numerous
languages are available.

There are six types of keys: typewriter keys, function keys, soft keys,
Hot keys, Windows special keys and keypad overlay.

Typewriter keys

The typewriter keys produce the upper- and lower-case letters, numbers,
punctuation marks, and special symbols that appear on the screen.

There are some differences, however, between using a typewriter and
using a computer keyboard:

■ Letters and numbers produced in computer text vary in width. Spaces,

which are created by a “space character,” may also vary depending on
line justification and other factors.

■ The lowercase l (el) and the number 1 (one) are not interchangeable on

computers as they are on a typewriter.

■ The uppercase O (oh) and the 0 (zero) are not interchangeable.

■ The Caps Lock function key locks only the alphabetic characters in

uppercase while the shift lock on a typewriter places all keys in the
shifted position.

■ The Shift keys, the Tab key, and the BkSp (backspace) key perform the

same function as their typewriter counterparts but also have special
computer functions.

Chapter 5

User’s Manual 5-1

The Keyboard

Function keys: F1 … F12

The function keys (not to be confused with Fn) are the 12 keys at the top of
your keyboard. These keys function differently from other keys.

F1 through F12 are called function keys because they execute
programmed functions when pressed. Used in combination with the Fn key,
keys marked with icons execute specific functions on the computer.
Refer to the section, Soft keys: Fn key combinations, in this chapter.
The function executed by individual keys depends on the software you are
using.

Soft keys: Fn key combinations

The Fn (function) is unique to TOSHIBA computers and is used in
combination with other keys to form soft keys. Soft keys are key
combinations that enable, disable or configure specific features.

Some software may disable or interfere with soft-key operations.
Soft-key settings are not restored by the Standby feature.

Emulating keys on enhanced keyboard

Pause

PrtSc

Esc

F1

F3 F4 F5 F6 F7 F8 F9 F10 F11 F12

F2

Tab

~

`

CapsLock

Ctrl

Shift

#

!
1

QW RTYUI OP

$4%

@

2

3

E

ASDFGHJ KL

CXZB

Alt

&

^

68

5

7

V

_

(9 )

*

<

MN

,

+

{[}

?
/

Bk Sp

=

\

]

,,

Enter

,

Shift

Ctrl

-

0

:
;

>
.

Alt

SysReq

Scroll

Break

lock

Num

PgUp

Ins

Home

Del

End

PgDn

*

/

.

Lock

7

8 9

Home

PgUp

+

654

3

1

2

PgDn

End

0
Ins

Enter

.
Del

101-key enhanced keyboard layout

The keyboard is designed to provide all the features of the 101-key
enhanced keyboard. The 101/102-key enhanced keyboard has a numeric
keypad and scroll lock key. It also has additional Enter and Ctrl keys to the
right of the main keyboard. Since the keyboard is smaller and has fewer
keys, some of the enhanced keyboard functions must be simulated using
two keys instead of one on the larger keyboard.

Your software may require you to use keys that the keyboard does not
have. Pressing the Fn key and one of the following keys simulates the
enhanced keyboard’s functions.

5-2 User’s Manual

The Keyboard

Press Fn + F10 or Fn + F11 to access the integrated keypad. When
activated, the keys with gray markings on the bottom edge become
numeric keypad keys (Fn + F11) or cursor control keys (Fn + F10). Refer to
the Keypad overlay section in this chapter for more information on how to
operate these keys. The power on default for both settings is off.

Press Fn + F12 (ScrLock) to lock the cursor on a specific line. The power
on default is off.

Press Fn + Enter to simulate Enter on the enhanced keyboard’s numeric
keypad.

Press Fn + Ctrl to simulate the enhanced keyboard’s right Ctrl key.

Hot keys

Hot keys (Fn + a function or Esc key) let you enable or disable certain
features of the computers.

Sound mute: Pressing Fn + Esc in a Windows environment turns sound
on or off. When you press these hot keys, the current setting will change
and be displayed as an icon.

User’s Manual 5-3

The Keyboard

Instant security: Press Fn + F1 to blank the screen to prevent others from
accessing your data. To restore the screen and original settings, press any
key or press the Touch Pad. If a screensaver password is registered, a
dialog box will appear. Enter the screensaver password and click OK.
If no password is set, the screen will be restored when you press any key or
press the Touch Pad.

Power save mode: Pressing Fn + F2 changes the power save mode.
If you press Fn + F2 in a Windows environment, the settings dialog box for

the Power Save Mode, similar to the one below, is displayed. Continue
holding down Fn, and release and press F2 again to toggle between the
settings. Release both Fn and F2 to put the new setting into effect. You can
also change this setting through the Profile options in TOSHIBA Power
Saver.

Standby: When you press Fn + F3, the computer enters the Standby
mode. Before entering Standby, a dialog box appears asking for your
confirmation. This dialog box will not be displayed in the future when you
click the check box in it.

Hibernation: When you press Fn + F4, the computer enters the
Hibernation mode. Before entering Hibernation, a dialog box appears
asking for your confirmation. This dialog box will not be displayed in the
future when you click the check box in it.

5-4 User’s Manual

The Keyboard

Display selection: Press Fn + F5 to change the active display device.
When you press these hot keys, a dialog box appears. Only selectable
devices will be displayed. Hold down Fn and press F5 again to change the
device. When you release Fn and F5, the selected device will change.
If you hold down these hot keys for five seconds the selection will return to
the internal LCD.

Internal LCD screen Brightness: Pressing Fn + F6 decreases the LCD
screen brightness in decrements. When you press these hot keys, the
current setting will be displayed for two seconds by an icon. You can also
change this setting through the Screen brightness item of the Basic Setup
tab in TOSHIBA Power Saver.

Internal LCD screen Brightness: Pressing Fn + F7 increases the LCD
screen brightness in increments. When you press these hot keys, the
current setting will be displayed for two seconds by a pop-up icon. You can
also change this setting through the Screen brightness item of the Basic
Setup tab in TOSHIBA Power Saver.

■ The brightness level is always set at the maximum value for about

18 seconds, when the internal LCD screen turns on. After 18 seconds,
the brightness level will appear at the Power Save Mode setting or you
can change it manually.

■ LCD screen clarity increases with the brightness level.

Wireless setting: Fn + F8 are not used.

Touch Pad: Pressing Fn + F9 in a windows environment enables or

disables the Touch Pad function. When you press these hot keys, the
current setting will change and be displayed as an icon.

User’s Manual 5-5

The Keyboard

LCD screen resolution selection: Press Fn + Space keys to change
the display resolution. Each time when you press these hot keys,
the LCD screen resolution changes as follows: The available resolution
depends on the model. With XGA, you can change the resolution between
800 × 600 and 1024 × 768 pixels. With SXGA, between 800 × 600 and
1400 × 1050 pixels.

Optical media drive power icon: Press the Fn + Tab keys to turn the
power of the optical media drive on or eject the disc tray. A dialog box is
displayed when this hotkey is pressed. To choose between the functions,
press the Tab key while holding down the Fn key. The chosen function is
executed when the Fn + Tab keys are released.

TOSHIBA Zooming Utility (reduce): To reduce the icon size on the
desktop or the application window, press the 1 key while holding down the

Fn key.

TOSHIBA Zooming Utility (enlarge): To enlarge the icon size on the
desktop or the application window, press the 2 key while holding down the
Fn key.

Fn Sticky key

You can use the TOSHIBA Accessibility Utility to make the Fn key sticky,
that is, you can press it once, release it, and then press an “F number” key.
To start the TOSHIBA Accessibility Utility, click start, point to All
Programs, point to TOSHIBA, point to Utilities and click Accessibility.

5-6 User’s Manual