Toshiba RAS-10 EKV-EE, RAS-10 EAV-EE User Manual [ru]
ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ
ENGLISH
PУССКИЙ
Кондиционер (сплит-система)
для бытового использования
Внутренний блок
RAS-07, 10, 13, 16EKV
Наружный блок
RAS-07, 10, 13, 16EAV
1110255116
1110255116_EN.indd 1 2/13/13 2:47 PM
PRECAUTIONS FOR SAFETY
●
Do not install, repair, open or remove the cover. It may
expose you to dangerous voltages. Ask the dealer or the
specialist to do this.
●
Turning off the power supply will not prevent potential
0
DANGER
0
WARNING
0
CAUTION
1
INDOOR UNIT DISPLAY
2
PREPARATION BEFORE USE
Preparing Filters
1. Open the air inlet grille and remove the air filters.
2. Attach the filters. (see detail in the accessory
sheet).
Loading Batteries (when use wireless operation.)
1. Remove the slide cover.
2. Insert 2 new batteries (AAA type) following the (+)
and (–) positions.
Remote Control Reset
1. Remove the batteries.
2. Press
3. Insert the batteries.
electric shock.
●
The appliance shall be installed in accordance with
national wiring regulation.
●
Means for disconnection from the supply having a
contact separation of at least 3 mm in all poles must be
incorporated in the fixed wiring.
●
Do not expose your body directly to cool air for a long
time.
●
Do not insert your finger or any article into the air inlet/
outlet.
●
When an abnormality (burning smell, etc.) occurs, stop
the air conditioner and disconnect the power supply or
turn off the breaker.
●
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
●
Children should be supervised to ensure that they do not
play with the appliance.
●
Do not use any refrigerant different from the one specified
for complement or replacement. Otherwise, abnormally
high pressure may be generated in the refrigeration
cycle, which may result in a failure or explosion of the
product or an injury to your body.
●
Do not wash the unit with water. It may cause an electric
shock.
●
Do not use this air conditioner for other purposes such as
preserving food, breeding animal, etc.
●
Do not step or put anything on the indoor/outdoor unit. It
may cause an injury or damage the unit.
●
Do not touch aluminium fin because it may cause an
injury.
●
Before cleaning the unit, turn off the main switch or the
circuit breaker.
●
When the unit won’t be used for a long time, turn off the
main switch or the circuit breaker.
●
It is recommended that maintenance be performed by
a specialist when the unit has been operated for a long
time.
●
The manufacturer shall not assume any liability for the
damage caused by not observing the description of this
manual.
1 TIMER (Yellow)
2 OPERATION (Green)
3 RESET button
.
3
AIRFLOW DIRECTION
FIX
Press
1
the desired vertical direction.
Press
2
automatically and press again to
stop.
For horizontal direction, adjust
3
manually.
Note:
● Do not move the louver manually by others.
● The louver may automation positioning by some operation mode.
4
REMOTE CONTROL
1 Infrared signal emitter
2 Start/Stop button
3 Mode select button (MODE)
4 Temperature button (TEMP)
5 Fan speed button (FAN)
6 Swing louver button (SWING)
7 Set louver button (FIX)
8 Off timer button (OFF)
9 High power button (Hi-POWER)
! Economy button (ECO)
" Clear button (CLEAR)
# Check button (CHECK)
5
AUTOMATIC OPERATION
To automatically select cooling, heating, or fan only operation
1. Press
2. Press : Set the desired temperature.
3. Press
MED+ , or HIGH .
COOLING / HEATING / FAN ONLY
6
OPERATION
1. Press
2. Press : Set the desired temperature.
Cooling: Min. 17°C, Heating: Max. 30°C, Fan Only:
No temperature indication
3. Press
MED+ , or HIGH .
7
DRY OPERATION
For dehumidification, a moderate cooling performance is controlled
automatically.
1. Press
2. Press : Set the desired temperature.
8
Hi-POWER OPERATION
To automatically control room temperature and airflow for faster cooling or
heating operation (except in DRY and FAN ONLY mode)
Press
Hi POWER
: Move the louver in
SWING
: Swing the air
3
2
7
9
8
#
MODE
: Select A.
FAN
: Select AUTO, LOW , LOW+ , MED ,
MODE
: Select Cool , Heat , or Fan only .
FAN
: Select AUTO, LOW , LOW+ , MED ,
MODE
: Select Dry .
: Start and stop the operation.
1
4
6
5
!
"
1110255116_EN.indd 21110255116_EN.indd 2 2/13/13 2:48 PM2/13/13 2:48 PM
Loading...