Toshiba mv20p2 Diagram

FILE NO. 140-200402

DOCUMENT CREATED IN JAPAN, Jan., 2004

SERVICE MANUAL

COLOR TELEVISION/
VIDEO CASSETTE RECORDER

MV20P2

SERVICING NOTICES ON CHECKING

As for the places which need special attentions,
they are indicated with the labels or seals on the
cabinet, chassis and parts. Make sure to keep the
indications and notices in the operation manual.

2. AVOID AN ELECTRIC SHOCK

There is a high voltage part inside. Avoid an
electric shock while the electric current is
flowing.

3. USE THE DESIGNATED PARTS

The parts in this equipment have the specific
characters of incombustibility and withstand
voltage for safety. Therefore, the part which is
replaced should be used the part which has
the same character.
Especially as to the important parts for safety
which is indicated in the circuit diagram or the
table of parts as a mark, the designated
parts must be used.

4. PUT PARTS AND WIRES IN THE
ORIGINAL POSITION AFTER
ASSEMBLING OR WIRING

There are parts which use the insulation
material such as a tube or tape for safety, or
which are assembled in the condition that
these do not contact with the printed board.
The inside wiring is designed not to get closer
to the pyrogenic parts and high voltage parts.
Therefore, put these parts in the original
positions.

5. TAKE CARE TO DEAL WITH THE
CATHODE-RAY TUBE

In the condition that an explosion-proof cathode­ray tube is set in this equipment, safety is
secured against implosion. However, when
removing it or serving from backward, it is
dangerous to give a shock. Take enough care to
deal with it.

6. AVOID AN X-RAY1. KEEP THE NOTICES

Safety is secured against an X-ray by consider­ing about the cathode-ray tube and the high
voltage peripheral circuit, etc.
Therefore, when repairing the high voltage pe­ripheral circuit, use the designated parts and
make sure not modify the circuit.
Repairing except indicates causes rising of high
voltage, and it emits an X-ray from the cathode­ray tube.

PERFORM A SAFETY CHECK AFTER

7.
SERVICING

Confirm that the screws, parts and wiring which
were removed in order to service are put in the
original positions, or whether there are the
portions which are deteriorated around the
serviced places serviced or not. Check the
insulation between the antenna terminal or
external metal and the AC cord plug blades.
And be sure the safety of that.

(INSULATION CHECK PROCEDURE)

1.

Unplug the plug from the AC outlet.

2.

Remove the antenna terminal on TV and turn
on the TV.

3.

Insulation resistance between the cord plug
terminals and the eternal exposure metal
[Note 2] should be more than 1M ohm by
using the 500V insulation resistance meter
[Note 1].

4.

If the insulation resistance is less than 1M
ohm, the inspection repair should be
required.

[Note 1]

If you have not the 500V insulation
resistance meter, use a Tester.

[Note 2]

External exposure metal: Antenna terminal

HOW TO ORDER PARTS

Please include the following informations when you order parts. (Particularly the VERSION LETTER.)

1. MODEL NUMBER and VERSION LETTER
The MODEL NUMBER can be found on the back of each product and the VERSION LETTER can be

found at the end of the SERIAL NUMBER.

2. PART NO. and DESCRIPTION
You can find it in your SERVICE MANUAL.

A1-1

TAPE REMOVAL METHOD AT NO POWER SUPPLY

1.

Remove the VCR block from the main unit.

(Refer to item 1 of the DISASSEMBLY INSTRUCTIONS.)

2.

Remove the screw 1 of the Deck Chassis and remove the Loading Motor.

3.

Rotate the Pinch Roller Cam in the direction of the arrow by hand to slacken the Video Tape.

4.

Rotate the Clutch Ass'y either of the directions to wind the Video Tape in the Cassette Case.

5.

Repeat the above step 3~4. Then take out the Video Cassette from the Deck Chassis. Be careful not to
scratch on the tape.

Loading Motor

Screw 1

Capstan DD Unit

Pinch Roller Cam

Main Cam

Clutch Ass'y

Main Chassis (Front Side)

A1-2

TABLE OF CONTENTS

SERVICING NOTICES ON CHECKING.....................................................................................

HOW TO ORDER PARTS ..........................................................................................................

TAPE REMOVAL METHOD AT NO POWER SUPPLY ............................................................

TABLE OF CONTENTS..............................................................................................................

GENERAL SPECIFICATIONS ...................................................................................................

DISASSEMBLY INSTRUCTIONS

1. REMOVAL OF MECHANICAL PARTS AND P. C. BOARDS............................................

2. REMOVAL OF VCR DECK PARTS ...................................................................................

3. REMOVAL OF ANODE CAP..............................................................................................

4. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC ...............................................

KEY TO ABBREVIATIONS ........................................................................................................

SERVICE MODE LIST ................................................................................................................

PREVENTIVE CHECKS AND SERVICE INTERVALS..............................................................

WHEN REPLACING EEPROM (MEMORY) IC ..........................................................................

SERVICING FIXTURES AND TOOLS .......................................................................................

PREPARATION FOR SERVICING.............................................................................................

MECHANICAL ADJUSTMENTS ................................................................................................

ELECTRICAL ADJUSTMENTS..................................................................................................

BLOCK DIAGRAMS

TV ............................................................................................................................................

Y/C/AUDIO/HEAD AMP ..........................................................................................................

MICON/IN/OUT/AV.................................................................................................................

PRINTED CIRCUIT BOARDS

SYSCON/CRT .........................................................................................................................

SCHEMATIC DIAGRAMS

Y/C/AUDIO/HEAD AMP ..........................................................................................................

MICON .....................................................................................................................................

IN/OUT .....................................................................................................................................

AV ............................................................................................................................................

CHROMA/IF.............................................................................................................................

SOUND AMP ...........................................................................................................................

POWER ...................................................................................................................................

DEFLECTION..........................................................................................................................

CRT ..........................................................................................................................................

INTERCONNECTION DIAGRAM ...............................................................................................

WAVEFORMS .............................................................................................................................

MECHANICAL EXPLODED VIEWS...........................................................................................

CHASSIS EXPLODED VIEWS ...................................................................................................

MECHANICAL REPLACEMENT PARTS LIST .........................................................................

CHASSIS REPLACEMENT PARTS LIST..................................................................................

ELECTRICAL REPLACEMENT PARTS LIST...........................................................................

A1-1
A1-1
A1-2
A2-1
A3-1~A3-5

B1-1, B1-2
B2-1~B2-6
B3-1
B4-1, B4-2
C1-1, C1-2
C2-1
C3-1, C3-2
C4-1
D1-1
D1-1
D2-1~D2-4
D3-1~D3-6

E-1, E-2
E-3, E-4
E-5, E-6

F-1~F-4

G-1, G-2
G-3, G-4
G-5, G-6
G-7, G-8
G-9, G-10
G-11, G-12
G-13, G-14
G-15, G-16
G-17, G-18
G-19, G-20
H-1, H-2
I1-1~I1-3
I2-1, I2-2
J1-1
J2-1
J3-1~J3-4

A2-1

GENERAL SPECIFICATIONS

G-1 TV CRT CRT Size / Visual Size 20 inch / 508.0 mmV

G-2 VCR System VHS Player / Recorder

G-3 Tuning Broadcasting System US System M

G-4 Signal Video Signal Input Level 1 V p-p/75 ohm

System CRT Type Normal

Color System NTSC
Speaker 2Speaker

Sound Output MAX 0.75W + 0.75 W

System Video System NTSC

Hi-Fi STEREO No
NTSC PB ­Deck DECK OVD-7

Heads Video Head 2 Head

FM Audio Head No

Audio /Control Mono/Yes

Erase(Full Track Erase) Yes
Tape Rec PAL ­Speed NTSC SP/SLP

Play PAL -

Fast Forward / Rewind Time (Approx.) at 25oC FF:4'50"/REW:2'30"

Forward/Reverse NTSC or PAL-M SP/SLP=3x,5x/9x,15x
Picture Search PAL or SECAM ­Frame Advance ­Slow Speed -

System Tuner and System 1Tuner

Receive CH Destination US(w/CATV)

Intermediate Picture(FP) 45.75MHz
Frequency Sound(FS) 41.25MHz

Preset CH
Stereo/Dual TV Sound
Tuner Sound Muting Yes

Audio Signal

Hi-Fi Audio Signal Dynamic Range : More than -

Deflection 90 degree
Magnetic Field BV/BH +0.45G / 0.18G

Position Front
Size 3 inch
Impedance 8 ohm

10%(Typical) 0.5W + 0.5 W

Loading System Front
Motor 3

NTSC SP/SLP

with Cassette T-120

Tuning System F-Synth
Input Impedance VHF/UHF 75 ohm

CH Coverage

FP-FS 4.5MHz

Output Level ­S/N Ratio (Weighted) 50dB
Horizontal Resolution at SP Mode 220Lines
Input Level
Output Level
S/N Ratio at SP (Weighted) 38dB

Harmonic Distortion at SP(1KHz) Typical 1.5 %

Frequency Response at SP 100Hz - 10kHz

at LP -

at SLP 100Hz - 4kHz

Frequency Response ­Wow And Flutter : Less than ­Channel Separation : More than ­Harmonic Distortion : Less than -

2~69, 4A,A-5~A-1, A~I,
J~W,W+1~W+84

-8dBm/50k ohm

-

No
No

A3-1

GENERAL SPECIFICATIONS

G-5 Power Power Source AC 120V 60Hz

Power Consumption at AC 86 W at 120V 60Hz

Protector Power Fuse Yes

G-6 Regulation Safety UL

G-7 Temperature Operation +5oC ~ +40oC

G-8 Operating Humidity Less than 80% RH
G-9 On Screen Menu Yes

Display Menu Type Icon

System Setup Yes

TV Setup Yes

Channel Setup Yes

V-chip Setup Yes

Tape Setup Yes

G-CODE(or SHOWVIEW or PLUSCODE)No. Entry
Clock Yes
CH/AV(Line) Yes
Tape Counter(Linear Counter) Yes
Tape Speed Yes
Sleep Time Yes
Stereo/Audio Output

Control Volume Yes
Level Bright / Contrast / Sharpness / Color Yes

Tint Yes

Bass/Treble/Balance

Manual Tracking Yes
Play/Stop/FF/Rew/Rec/OTR/T-Rec/Pause/Eject/Tape In (Symbol Mark)

Auto Tracking/Manual Tracking Yes
Caption / Text Yes
Index Yes
Mute Yes
Hi-Fi
Repeat Yes
Zero Return Yes
DEW

G-10 OSD Language English French Spanish
G-11 Clock,Timer Calendar 1990/1/1 ~ 2081/12/31

and Timer Timer Events 8 prog/ 1 month
Back-up One Touch Recording Max Time 6 Hours

OTPB Valid Time No
Sleep Timer Max Time 120

On/Off Timer Program(On Timer / Off Timer) 1
Auto Shut Off No Signal 15

Timer Back-up (at Power Off Mode) 5

DC -

Stand by (at AC) 5 W at 120V 60 Hz
Per Year -

Safety Circuit Yes
IC Protector(Micro Fuse) No
Dew Sensor

Radiation FCC
X-Radiation DHHS

Storage -20oC ~ +60oC

Clock Set Yes
On/Off Timer Set Yes
Auto Clock On/Off Yes
Standard Time Yes
Daylight Saving Time Yes

Language Yes
Picture Yes
Audio
Picture Preference Yes

TV/CATV Yes
Auto CH Memory Yes
Add/ Delete Yes

Timer Rec Set Yes
Auto Repeat On/Off Yes

Bilingual
SAP

Step 10

No Operation -

at DC -

No

No

No

No
No
No

No

Yes

No

No

min.
min.
prog.
min.

sec.

A3-2

GENERAL SPECIFICATIONS

G-12 Remote Unit RC-JG

Control Glow in Dark Remocon Yes

Format NEC
Custom Code 40-BFh , 44-BBh
Power Source Voltage(D.C) 3V

Total Keys 44
Keys Power Yes

UM size x pcs UM-4 x 2 pcs

1 Yes
2 Yes
3 Yes
4 Yes
5 Yes
6 Yes
7 Yes
8 Yes
9 Yes
0 Yes
CH Up Yes
CH Down Yes
Volume Up Yes
Volume Down Yes
Input Select Yes
Play Yes
F.Fwd Yes
Rew Yes
Pause/Still Yes
Stop Yes
Index+ Yes
Index- Yes

T-REC
Rec(T-Rec/OTR)
Rec/OTR

Eject Yes
Counter Reset Yes
Speed Yes
TV Monitor Yes
Quick View(Channel Return) Yes
Program Yes
Slow
Auto Tracking(Digital Tracking) Yes
Tracking+ Yes
Tracking - Yes
Menu Yes
Enter Yes
Cancel Yes
Call Yes
Closed Caption(TV/Caption/Text) Yes
Sleep Timer Yes
Mute Yes
Zero Return Yes
CM Skip(Skip Search) Yes
Audio Select

Yes
Yes
Yes

Keys

No

No

A3-3

GENERAL SPECIFICATIONS

G-13 Features Auto Head Cleaning

Auto Tracking Yes
HQ (VHS Standard High Quality) Yes
Auto Power On, Auto Play, Auto Rewind, Auto Eject Yes
VIDEO PLUS+(SHOWVIEW,G-CODE)
Auto Clock Yes
Forward / Reverse Picture Search Yes
One Touch Playback
Auto CH Memory Yes
Closed Caption Yes
TV Auto Shut off Function Yes
End Call
Index Search Yes
SQPB
CATV Yes
CM Skip(30sec x 6 Times) Yes
Comb Filter
TV Monitor Yes
Program Extend
Choke Coil
Energy Star Yes
Dirty Head
V-chip USA V-chip Yes

CANADA V-chip
CM Advance
Movie Advance
Zero Return Yes
Power On Memory
Picture Preference Yes
Auto Setup Yes
Protect of FBT Leak Circuit Yes

G-14 Accessories Owner's Manual Language English

w/Guarantee Card Yes
Remote Control Unit Yes
Battery Yes

UM size x pcs UM-4 x 2 pcs

OEM Brand No
Rod Antenna

Poles -

Terminal -

W/300 ohm to 75 ohm antenna adapter -

Loop Antenna

Terminal ­U/V Mixer
300 ohm to 75 ohm Antenna Adapter Yes
Antenna Change Plug
DC Car Cord (Center+)
AC Plug Adapter
AC Cord
AV Cord (2Pin-1Pin)
Guarantee Card
Registration Card Yes
ESP Card Yes
Warning Sheet
Dew/AHC Caution Sheet
Quick Set-up Sheet
Circuit Diagram
Service Facility List
Important Safeguard
Sheet Information (Return) Yes

No

No

No

No

No

No

No
No

No

No
No
No

No

No

No

No

No
No
No
No
No
No

No
No
No
No
No
No

A3-4

GENERAL SPECIFICATIONS

G-15 Interface Switch Power Yes

Indicator Power

Key Light up Rec/OTR

Terminals Front Video Input RCA x 1

Rear Video Input

G-16 Set Size Approx. W x D x H (mm) 502 x 488.7 x 513
G-17 Weight Net (Approx.) 22.0 kg( 48.5 lbs)

G-18 Carton Master Carton

Gift Box Yes

Drop Test Natural Dropping At

Container Stuffing(40' container) 240

G-19 Material Cabinet Front PS 94V0 DECABROM

PCB Non-Halogen Demand No

G-20 Environment Pb Free Lead-free Solder No

Cd Free No

Play Yes

Pause/Still

One Touch Playback

Channel Up Yes

Channel Down Yes

F.FWD/Cue Yes

Eject/Stop Yes

Main Power SW

Volume Up Yes

Volume Down Yes

Rew/Rev Yes

Rec/OTR Yes

Input Select

Rec/OTR Yes (Red)

T-Rec Yes (Red)

On Timer

CS

One Touch Playback

Play

Audio Input RCA x 1

Other Terminal Head Phone(Stereo & Mono, 3.5mm)

Audio Input

Video Output

Audio Output

Euro Scart

Diversity

Ext Speaker

DC Jack 12V(Center +)

VHF/UHF Antenna Input

AC Inlet

Gross (Approx.) 24.0 kg( 52.9 lbs)

Content -

Material -

Dimensions W x D x H(mm) -

Description of Origin -

Material Double/White

Dimensions W x D x H(mm) 594 x 569 x 620

Design As per Buyer's

Description of Origin Yes

Height (cm) 46

Rear PS 94V0 DECABROM

Jack Panel -

Eyelet Demand Yes

Other No

F Type

No
No

No

No
No

No
No
No
No
No

No
No
No
No
No
No
No
No

No

No

1 Corner / 3 Edges / 6 Surfaces

Sets

A3-5

DISASSEMBLY INSTRUCTIONS

1. REMOVAL OF MECHANICAL PARTS
AND P.C. BOARDS

1-1: BACK CABINET (Refer to Fig. 1-1)

1.

Remove the 7 screws 1.

2.

Remove the AC cord from the AC cord hook 2.

3.

Remove the Back Cabinet in the direction of arrow.

Front Cabinet

1

1

1

1

1

1

1

1-2: CRT PCB (Refer to Fig. 1-2)
CAUTION: BEFORE REMOVING THE ANODE CAP,

DISCHARGE ELECTRICITY BECAUSE IT
CONTAINS HIGH VOLTAGE.
BEFORE ATTEMPTING TO REMOVE OR
REPAIR ANY PCB, UNPLUG THE POWER
CORD FROM THE AC SOURCE.

1.

Remove the Anode Cap.
(Refer to REMOVAL OF ANODE CAP)

2.

Disconnect the following connector: (CP801).

3.

Remove the CRT PCB in the direction of arrow.

2

Back Cabinet

Fig. 1-1

1-3: TV/VCR BLOCK (Refer to Fig. 1-3)

1.

Remove the 2 screws 1.

2.

Disconnect the following connectors:
(CP352, CP354, CP401 and CP502).

3.

Unlock the support 2.

4.

Remove the TV/VCR Block in the direction of arrow.

Front Cabinet

1

TV/VCR Block

1-4: DECK SHIELD PLATE (Refer to Fig. 1-4)

1.

Remove the 2 screws 1.

2.

Remove the screw 2.

3.

Remove the Deck Shield Plate in direction of arrow.

2

1

1

Deck Shield Plate

1

2

UP TO
RELEASE

Fig. 1-3

Front Cabinet

CRT PCB

TV/VCR Block

Fig. 1-4

Fig. 1-2

B1-1

DISASSEMBLY INSTRUCTIONS

1-5: DECK CHASSIS (Refer to Fig. 1-5)
NOTE

Do not remove the cable at the FE Head section. The FE
Head may be damaged if you remove the cable by force.

1.

Remove the screw 1.

2.

Remove the FE Head.

3.

Remove the 3 screws 2.

4.

Disconnect the following connectors:
(CP1001, CP4001 and CP4002).

5.

Remove the Deck Chassis in the direction of arrow.

2

1

2

FE Head

Deck Chassis

2

Syscon PCB

1-6: SYSCON PCB (Refer to Fig. 1-6)

1.2.Remove the screw 1.

Remove the Syscon PCB in the direction of arrow.

Syscon PCB

1

Deck Holder

Fig. 1-5

Fig. 1-6

B1-2

DISASSEMBLY INSTRUCTIONS

2. REMOVAL OF VCR DECK PARTS

2-1: TOP BRACKET (Refer to Fig. 2-1)

Extend the 2 supports 1.

1.

Slide the 2 supports 2 and remove the Top Bracket.

2.

NOTE

After the installation of the Top Bracket, bend the support

1.

1 so that the Top Bracket is fixed.

Top Bracket

1

Top Bracket

2

Main Chassis

2

Main Chassis

2-2: CASSETTE HOLDER ASS'Y (Refer to Fig. 2-2)

1.

Move the Cassette Holder Ass'y to the front side.

2.

Push the Locker R to remove the Cassette Side R.

3.

Remove the Cassette Side L.

Cassette Side R

Main Chassis

1

Locker R

Fig. 2-1

NOTE

1.2.In case of the Locker R installation, check if the one
position of Fig.2-3-B are correctly locked.
When you install the Cassette Side R, be sure to move
the Locker R after installing.

Locker R

Check if this position

Cassette Side R

is locked.

Fig. 2-3-B

2-4: LINK UNIT (Refer to Fig. 2-4)

1.

Set the Link Unit to the Eject position.

2.

Unlock the support 1.

3.

Remove the (A) side of the Link Unit first, then remove
the (B) side.

Main Chassis

Link Unit

Link Unit

Cassette Side L

Main Chassis

2-3: CASSETTE SIDE L/R (Refer to Fig. 2-3-A)

1.

Remove the Locker Spring.

2.

Unlock the 4 supports 1 and then remove the Cassette
Side L/R.

3.

Unlock the support 2 and then remove the Locker R.

Locker Spring

1

1

2

Cassette Side R

Cassette Holder

Locker R

1

1

Cassette Side L

Fig. 2-2

(A)

(B)

Link Unit

2-5: LINK LEVER/FLAP LEVER/BOT COVER

(Refer to Fig. 2-5)

Unlock the support 1.

1.
Remove the BOT Cover.

2.
Extend the support 2.

3.
Remove the Link Lever.

4.
Remove the Flap Lever.

5.

1

2

Flap Lever

BOT Cover

Link Lever

Main Chassis

Fig. 2-4

Fig. 2-3-A

Fig. 2-5

B2-1

DISASSEMBLY INSTRUCTIONS

2-6: LOADING MOTOR/WORM (Refer to Fig. 2-6-A)

1.

Remove the screw 1.

2.

Remove the Loading Motor.

3.

Remove the Worm.

Loading Motor

Worm

Main Chassis

• Screw Torque: 3 ± 0.5kgf•cm

1

Fig. 2-6-A

NOTE

1.

In case of the Worm installation, check if the value of the
Fig. 2-6-B is correct.

2.

In case of the Loading Motor installation, hook the wire on
the Cassette Opener as shown Fig. 2-6-C.

3.

When installing the wires between Capstan DD Unit and
Loading Motor, connect them correctly as shown Fig. 2-6-D.

19.2 ± 0.1mm

2-7: TENSION ASS’Y (Refer to Fig. 2-7-B)

1.

Turn the Pinch Roller Cam clockwise so that the Tension
Holder hook is set to the position of Fig. 2-7-A to move
the Tension Arm Ass’y.

2.

Remove the Tension Spring.

3.

Unlock the 2 supports 1 and remove the Tension Band.

4.

Unlock the support 2 and remove the Tension Arm Ass’y.

5.

Unlock the support 3 and remove the Tension Connect.

6.

Float the hook 4 and turn it clockwise then remove the
Tension Holder.

Tension Arm Ass’y

Fig. 2-7-A

1

Tension Connect

Tension Spring

2

4

1

3

Tension Holder

Tension Band

Tension Arm Ass’y

Loading Motor

-

+

Safety surface for pressing
of the insert.

Pink

White

Fig. 2-6-B

Loading Motor

Cassette Opener

Fig. 2-6-C

Capstan DD Unit

L2

L1

Fig. 2-6-D

B2-2

Fig. 2-7-B

NOTE

1.

In case of the Tension Band installation, note the direc­tion of the installation. (Refer to Fig. 2-7-C)

2.

In case of the Tension Band installation, install correctly
as Fig. 2-7-D.

3.

In case of the Tension Connect installation, install as the
circled section of Fig. 2-7-E.

Tension Connect

Tension Band

Fig. 2-7-C

[OK]

[NG]

Tension Connect

Tension Connect

Tension Connect

DISASSEMBLY INSTRUCTIONS

NOTE

1.

Take care not to damage the gears of the S Reel and T

Tension Band

Tension Band

Fig. 2-7-D

Reel.

2.

The Polyslider Washer may be remained on the back of
the reel.

3.

Take care not to damage the shaft.

4.

Do not touch the section “A” of S Reel and T Reel. (Use
gloves.) (Refer to Fig. 2-9-A) Do not adhere the stains
on it.

5.

When you install the reel, clean the shaft and grease it. (If
you do not grease, noise may be heard in FF/REW
mode.)

6.

After installing the reel, adjust the height of the reel.

(Refer to MECHANICAL ADJUSTMENT)

Main Chassis

Fig. 2-7-E

2-8: T BRAKE ARM/T BRAKE BAND (Refer to Fig. 2-8-A)

Remove the T Brake Spring.

1.
Turn the T Brake Arm clockwise and bend the hook

2.
section to remove it.
Unlock the 2 supports 1 and remove the T Brake Band.

3.

T Brake Band

Hook section

1

1

T Brake Arm

T Brake Spring

Fig. 2-8-A

NOTE

1. In case of the T Brake Band installation, install correctly
as Fig. 2-8-B.

Idler Gear

Idler Arm Ass’y

S Reel

(A)

(B)

T Reel

1

(A)

1

Fig. 2-9-A

NOTE

1.2.In case of the S Reel and T Reel installation, check if the
correct parts are installed. (Refer to Fig. 2-9-B)
In case of the Idler Arm Ass’y installation, install correctly
as Fig. 2-9-C. And also set it so that the section “B” of
Fig. 2-9-A is placed under the Main Chassis tab.

[OK]

T Brake Band

[NG]

T Brake Band

T Brake Arm

T Brake Arm

Fig. 2-8-B

2-9: S REEL/T REEL/IDLER ARM ASS’Y/IDLER GEAR

(Refer to Fig. 2-9-A)

1.

Remove the S Reel and T Reel.

2.

Remove the 2 Polyslider Washers 1.

3.

Remove the Idler Arm Ass’y and Idler Gear.

B2-3

[OK]

[NG]

Clutch Gear

Clutch Gear

Big Hole
(S Reel)

Small Hole
(T Reel)

Fig. 2-9-B

Idler Arm Ass’y

Idler Arm Ass’y

Fig. 2-9-C

DISASSEMBLY INSTRUCTIONS

2-10: CASSETTE OPENER/PINCH ROLLER BLOCK/P5

ARM ASS’Y (Refer to Fig. 2-10-A)

1.2.Unlock the support 1 and remove the Cassette Opener.
Remove the Pinch Roller Block and P5 Arm Ass’y.

1

Cassette Opener

Pinch Roller Block

P5 Arm Ass’y

Main Chassis

Fig. 2-10-A

NOTE

1.2.Do not touch the Pinch Roller. (Use gloves.)
In case of the Pinch Roller Block and the Pinch Roller
Cam installation, install correctly as Fig. 2-10-B.

Pinch Roller Block

P5 Arm Ass’y

Can be seen the hole of the
Main Cam.

Can be seen the hole of
the Pinch Roller Cam.

Fig. 2-10-B

2-11: A/C HEAD (Refer to Fig. 2-11-A)

1.

Remove the screw 1.

2.

Remove the A/C Head Base.

3.

Remove the 3 screws 2.

4.

Remove the A/C Head and A/C Head Spring.

NOTE

1.

Do not touch the A/C Head. (Use gloves.)

2.

When you install the A/C Head Spring, install as shown in
Fig. 2-11-B.

3.

When you install the A/C Head, tighten the screw (1) first,
then tighten the screw (2), finally tighten the screw (3).

Spring Position

Fig. 2-11-B

2-12: FE HEAD (RECORDER ONLY) (Refer to Fig. 2-12)

Remove the screw 1.

1.
Remove the FE Head.

2.

1

FE Head

• Screw Torque: 5 ± 0.5kgf•cm

• The FE Head is not installed on the Video Cassette Player.

Fig. 2-12

2-13: CYLINDER UNIT ASS'Y (Refer to Fig. 2-13)

Disconnect the following connector:

1.
(CD2001)
Remove the 3 screws 1.

2.
Remove the Cylinder Unit Ass'y.

3.

NOTE

When you install the Cylinder Unit Ass'y, tighten the

1.
screws from (1) to (3) in order while pulling the Ass'y
toward the left front direction.

Cylinder Unit Ass'y

(1)

2

2

(2)

1

• Screw Torque: 5 ± 0.5kgf•cm (Screw 1)

(3)

2

A/C Head

A/C Head Spring

A/C Head Base

Fig. 2-11-A

B2-4

• Screw Torque: 3 ± 0.5kgf•cm

(3)

(2)

(1)

1

1

1

Fig. 2-13

DISASSEMBLY INSTRUCTIONS

2-14: CAPSTAN DD UNIT (Refer to Fig. 2-14-A)

1.

Remove the Capstan Belt.

2.

Remove the 3 screws 1.

3.

Remove the Capstan DD Unit.

Capstan Belt

Capstan DD Unit

1

1

1

• Screw Torque: 4 ± 0.5kgf•cm

Fig. 2-14-A

NOTE

1. In case of the Capstan DD Unit installation, apply the
silicon bond (TSE3843-W) on the position Fig. 2-14-B
correctly. (If no silicon bond applied, abnormal noise will
be heard on the deck operation.)

(Refer to Fig. 2-14-B, C)

Applied position of
silicon bond

2-15: MAIN CAM/PINCH ROLLER CAM/JOINT GEAR

(Refer to Fig. 2-15-A)

1.2.Remove the E-Ring 1, then remove the Main Cam.
Remove the E-Ring 2, then remove the Pinch Roller
Cam and Joint Gear.

1

Main Cam

2

Pinch Roller Cam

Joint Gear

Fig. 2-15-A

NOTE

1. In case of the Pinch Roller Cam and Main Cam installa­tion, install them as the circled section of Fig. 2-15-B so
that the each markers are met. (Refer to Fig. 2-15-B)
And also can be seen the Main Chassis hole through the
Main Cam maker hole.

Pinch Roller Cam

Marker

Main Cam

Be careful not to apply the silicon
bond to the Pinch Roller.

Capstan DD Unit

Silicon Bond

Main Chassis

Fig. 2-14-B

Fig. 2-14-C

2-16: LOADING GEAR S/T UNIT (Refer to Fig. 2-16-A)

1.2.Remove the E-Ring 1 and remove the Main Loading
Gear.
Remove the Main Rod, Tension Lever, Loading Arm S
Unit and Loading Arm T Unit.

1

Main Rod

Tension Lever

Main Loading Gear

Loading Arm S Unit

B2-5

Fig. 2-15-B

Loading Arm T Unit

Fig. 2-16-A

DISASSEMBLY INSTRUCTIONS

NOTE

1. When you install the Loading Arm S Unit, Loading Arm T
Unit and Main Loading Gear, align each marker. (Refer

to Fig. 2-16-B)

Marker

Main Loading Gear

Marker

Loading Arm T Unit Loading Arm S Unit

Fig. 2-16-B

2-17: CLUTCH ASS’Y/RING SPRING/CLUTCH LEVER/

CLUTCH GEAR (Refer to Fig. 2-17-A)

1.

Remove the Polyslider Washer 1.

2.

Remove the Clutch Ass’y and Ring Spring.

3.

Remove the Clutch Lever.

4.

Remove the Coupling Gear, Coupling Spring and Clutch
Gear.

2-18:

CASSETTE GUIDE POST/INCLINED BASE S/T
UNIT/P4 CAP/LED REFLECTOR
(Refer to Fig. 2-18-A)

Remove the P4 Cap.

1.
Unlock the support 1 and remove the Cassette Guide

2.
Post.
Remove the Inclined Base S/T Unit.

3.
Remove the screw 2.

4.
Remove the LED Reflector.

5.

1

Inclined Base S Unit

LED Reflector

Cassette Guide Post

Inclined Base T Unit

P4 Cap

1

Clutch Ass’y

Ring Spring

Coupling Gear

Coupling Spring

Clutch Gear

Clutch Lever

Fig. 2-17-A

NOTE

1. In case of the Clutch Ass’y installation, install it with
inserting the spring of the Clutch Ass’y into the dent of the
Coupling Gear. (Refer to Fig. 2-17-B)

Clutch Ass’y

2

Fig. 2-18-A

NOTE

1.

Do not touch the roller of Guide Roller.

2.

In case of the P4 Cap installation, install it with parallel
for “A” and “B” of Fig. 2-18-B.

3.

In case of the Cassette Guide Post installation, install
correctly as the circled section of Fig. 2-18-C.

“A” “B”

P4 Cap

Cassette Opener

Fig. 2-18-B

[OK]

Cassette Guide Post

Coupling Gear

Fig. 2-17-B

[NG]

Cassette Guide Post

Fig. 2-18-C

B2-6

DISASSEMBLY INSTRUCTIONS

3. REMOVAL OF ANODE CAP

Read the following NOTED items before starting work.

After turning the power off there might still be a potential

*

voltage that is very dangerous. When removing the
Anode Cap, make sure to discharge the Anode Cap's
potential voltage.

*

Do not use pliers to loosen or tighten the Anode Cap
terminal, this may cause the spring to be damaged.

REMOVAL

1. Follow the steps as follows to discharge the Anode Cap.

(Refer to Fig. 3-1.)

Connect one end of an Alligator Clip to the metal part of a
flat-blade screwdriver and the other end to ground.
While holding the plastic part of the insulated Screwdriver,
touch the support of the Anode with the tip of the
Screwdriver.
A cracking noise will be heard as the voltage is discharged.

GND on the CRT

3. After one side is removed, pull in the opposite direction to
remove the other.

NOTE

Take care not to damage the Rubber Cap.

INSTALLATION

1. Clean the spot where the cap was located with a small
amount of alcohol. (Refer to Fig. 3-3.)

NOTE

Confirm that there is no dirt, dust, etc. at the spot where
the cap was located.

Location of Anode Cap

Fig. 3-3

Screwdriver

Alligator Clip

GND on the CRT

Flip up the sides of the Rubber Cap in the direction of the

2.
arrow and remove one side of the support.

(Refer to Fig. 3-2.)

Rubber Cap

Support

CRT

Fig. 3-1

2.3.Arrange the wire of the Anode Cap and make sure the
wire is not twisted.
Turn over the Rubber Cap. (Refer to Fig. 3-4.)

Fig. 3-4

4. Insert one end of the Anode Support into the anode button,
then the other as shown in Fig. 3-5.

CRT

Support

Fig. 3-2

Support

CRT

5.6.Confirm that the Support is securely connected.
Put on the Rubber Cap without moving any parts.

B3-1

Fig. 3-5

DISASSEMBLY INSTRUCTIONS

4.

REMOVAL AND INSTALLATION OF FLAT
PACKAGE IC

REMOVAL

Put the Masking Tape (cotton tape) around the Flat

1.
Package IC to protect other parts from any damage.

(Refer to Fig. 4-1.)
NOTE

Masking is carried out on all the parts located within 10
mm distance from IC leads.

When IC starts moving back and forth easily after

3.
desoldering completely, pickup the corner of the IC using a
tweezers and remove the IC by moving with the IC
desoldering machine. (Refer to Fig. 4-3.)

NOTE

Some ICs on the PCB are affixed with glue, so be
careful not to break or damage the foil of each IC leads
or solder lands under the IC when removing it.

Blower type IC
desoldering
machine

Masking Tape
(Cotton Tape)

Heat the IC leads using a blower type IC desoldering

2.

IC

machine. (Refer to Fig. 4-2.)

NOTE

Do not add the rotating and the back and forth
directions force on the IC, until IC can move back and
forth easily after desoldering the IC leads completely.

Blower type IC
desoldering machine

Fig. 4-1

Tweezers

IC

Peel off the Masking Tape.4.
Absorb the solder left on the pattern using the Braided

5.
Shield Wire. (Refer to Fig. 4-4.)

NOTE

Do not move the Braided Shield Wire in the vertical
direction towards the IC pattern.

Fig. 4-3

Braided Shield Wire

Soldering Iron

IC

Fig. 4-2

IC pattern

Fig. 4-4

B4-1

DISASSEMBLY INSTRUCTIONS

INSTALLATION

Take care of the polarity of new IC and then install the new

1.
IC fitting on the printed circuit pattern. Then solder each
lead on the diagonal positions of IC temporarily.

(Refer to Fig. 4-5.)

Soldering Iron

Solder temporarily

Supply the solder from the upper position of IC leads

2.
sliding to the lower position of the IC leads.
(Refer to Fig. 4-6.)

Solder temporarily

Fig. 4-5

When bridge-soldering between terminals and/or the

4.
soldering amount are not enough, resolder using a Thin-tip
Soldering Iron. (Refer to Fig. 4-8.)

Thin-tip Soldering Iron

IC

Fig. 4-8

Finally, confirm the soldering status on four sides of the IC

5.
using a magnifying glass.
Confirm that no abnormality is found on the soldering
position and installation position of the parts around the IC.
If some abnormality is found, correct by resoldering.

NOTE

When the IC leads are bent during soldering and/or
repairing, do not repair the bending of leads. If the
bending of leads are repaired, the pattern may be
damaged. So, always be sure to replace the IC in this
case.

Soldering IronSolder

IC

Supply soldering
from upper position
to lower position

Fig. 4-6

Absorb the solder left on the lead using the Braided Shield

3.
Wire. (Refer to Fig. 4-7.)

NOTE

Do not absorb the solder to excess.

Soldering Iron

IC

Braided Shield Wire

Fig. 4-7

B4-2

A

A/C
ACC
AE
AFC
AFT
AFT DET
AGC
AMP
ANT
A.PB
APC
ASS'Y
AT
AUTO
A/V

B

BGP
BOT
BPF
BRAKE SOL
BUFF
B/W

C

C
CASE
CAP
CARR
CH
CLK
CLOCK (SY-SE)
COMB
CONV
CPM
CTL
CYL
CYL-M
CYL SENS

D

DATA (SY-CE)
dB
DC
DD Unit
DEMOD
DET
DEV

E

E
EF
EMPH
ENC
ENV
EOT
EQ
EXT

F

F
FBC
FE
FF
FG
FL SW
FM
FSC
FWD

G

GEN
GND

KEY TO ABBREVIATIONS

:

Audio/Control

:

Automatic Color Control

:

Audio Erase

:

Automatic Frequency Control

:

Automatic Fine Tuning

:

Automatic Fine Tuning Detect

:

Automatic Gain Control

:

Amplifier

:

Antenna

:

Audio Playback

:

Automatic Phase Control

:

Assembly

:

All Time

:

Automatic

:

Audio/Video

:

Burst Gate Pulse

:

Beginning of Tape

:

Bandpass Filter

:

Brake Solenoid

:

Buffer

:

Black and White

:

Capacitance, Collector

:

Cassette

:

Capstan

:

Carrier

:

Channel

:

Clock

:

Clock (Syscon to Servo)

:

Combination, Comb Filter

:

Converter

:

Capstan Motor

:

Control

:

Cylinder

:

Cylinder-Motor

:

Cylinder-Sensor

:

Data (Syscon to Servo)

:

Decibel

:

Direct Current

:

Direct Drive Motor Unit

:

Demodulator

:

Detector

:

Deviation

:

Emitter

:

Emitter Follower

:

Emphasis

:

Encoder

:

Envelope

:

End of Tape

:

Equalizer

:

External

:

Fuse

:

Feed Back Clamp

:

Full Erase

:

Fast Forward, Flip-flop

:

Frequency Generator

:

Front Loading Switch

:

Frequency Modulation

:

Frequency Sub Carrier

:

Forward

:

Generator

:

Ground

H

H.P.F
H.SW
Hz

I

IC
IF
IND
INV

K

KIL

L

L
LED
LIMIT AMP
LM, LDM
LP
L.P.F
LUMI.

M

M
MAX
MINI
MIX
MM
MOD
MPX
MS SW

N

NC
NR

O

OSC
OPE

P

PB
PB CTL
PB-C
PB-Y
PCB
P. CON
PD
PG
P-P

R

R
REC
REC-C
REC-Y
REEL BRK
REEL S
REF
REG
REW
REV, RVS
RF
RMC
RY

S

S. CLK
S. COM
S. DATA
SEG
SEL
SENS
SER
SI
SIF
SO
SOL
SP

:

High Pass Filter

:

Head Switch

:

Hertz

:

Integrated Circuit

:

Intermediate Frequency

:

Indicator

:

Inverter

:

Killer

:

Left

:

Light Emitting Diode

:

Limiter Amplifier

:

Loading Motor

:

Long Play

:

Low Pass Filter

:

Luminance

:

Motor

:

Maximum

:

Minimum

:

Mixer, mixing

:

Monostable Multivibrator

:

Modulator, Modulation

:

Multiplexer, Multiplex

:

Mecha State Switch

:

Non Connection

:

Noise Reduction

:

Oscillator

:

Operation

:

Playback

:

Playback Control

:

Playback-Chrominance

:

Playback-Luminance

:

Printed Circuit Board

:

Power Control

:

Phase Detector

:

Pulse Generator

:

Peak-to Peak

:

Right

:

Recording

:

Recording-Chrominance

:

Recording-Luminance

:

Reel Brake

:

Reel Sensor

:

Reference

:

Regulated, Regulator

:

Rewind

:

Reverse

:

Radio Frequency

:

Remote Control

:

Relay

:

Serial Clock

:

Sensor Common

:

Serial Data

:

Segment

:

Select, Selector

:

Sensor

:

Search Mode

:

Serial Input

:

Sound Intermediate Frequency

:

Serial Output

:

Solenoid

:

Standard Play

C1-1

S

STB
SW
SYNC
SYNC SEP

T

TR
TRAC
TRICK PB
TP

U

UNREG

V

V
VCO
VIF
VP
V.PB
VR
V.REC
VSF
VSR
VSS
V-SYNC
VT

X

X'TAL

Y

Y/C

KEY TO ABBREVIATIONS

:

Serial Strobe

:

Switch

:

Synchronization

:

Sync Separator, Separation

:

Transistor

:

Tracking

:

Trick Playback

:

Test Point

:

Unregulated

:

Volt

:

Voltage Controlled Oscillator

:

Video Intermediate Frequency

:

Vertical Pulse, Voltage Display

:

Video Playback

:

Variable Resistor

:

Video Recording

:

Visual Search Fast Forward

:

Visual Search Rewind

:

Voltage Super Source

:

Vertical-Synchronization

:

Voltage Tuning

:

Crystal

:

Luminance/Chrominance

C1-2

SERVICE MODE LIST

This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily.
To enter SERVICE MODE, set the volume level to minimum. Then press and hold Vol (-) button of main unit and remocon key for

more than 2 seconds.

Set Key Remocon Key Operations

VOL. (-) MIN

VOL. (-) MIN 1

VOL. (-) MIN

VOL. (-) MIN

VOL. (-) MIN 4

VOL. (-) MIN 5

VOL. (-) MIN 6

0

2

3

Releasing of V-CHIP PASSWORD.

Initialization of the factory.
NOTE:

Horizontal position adjustment of OSD.
NOTE: Also can be adjusted by using the Adjustment MENU.
Refer to the "ELECTRICAL ADJUSTMENT" (OSD HORIZONTAL).

Adjust the PG SHIFTER automatically.
Refer to the "ELECTRICAL ADJUSTMENT" (PG SHIFTER).

Adjust the PG SHIFTER manually.
Refer to the "ELECTRICAL ADJUSTMENT" (PG SHIFTER).

Adjusting of the Tracking to the center position.

POWER ON total hours and PLAY/REC total hours are displayed on the screen.
Refer to the "PREVENTIVE CHECKS AND SERVICE INTERVALS" (CONFIRMATION
OF HOURS USED).

Can be checked of the INITIAL DATA of MEMORY IC.
Refer to the "WHEN REPLACING EEPROM (MEMORY) IC".

Do not use this for the normal servicing.
If you set a factory initialization, the memories are reset such as the clock
setting, the channel setting, the POWER ON total hours, and PLAY/REC
total hours.

VOL. (-) MIN 9

Method Operations

Make the short circuit between
the test point of SERVICE and
the GND.

Display of the Adjustment MENU on the screen.
Refer to the "ELECTRICAL ADJUSTMENT" (On-Screen Display Adjustment).

The BOT, EOT, and the Reel Sensor do not work and the deck can be operated
without a cassette tape.
Refer to the "PREPARATION FOR SERVICING"

C2-1

PREVENTIVE CHECKS AND SERVICE INTERVALS

The following standard table depends on environmental conditions and usage.
Parts replacing time does not mean the life span for individual parts.
Also, long term storage or misuse may cause transformation and aging of rubber parts.
The following list means standard hours, so the checking hours depends on the conditions.

Time

Parts Name

Audio Control Head

Full Erase Head

(Recorder only)

Capstan Belt

Pinch Roller

Capstan DD Unit

Loading Motor

Tension Band
T Brake Band

Clutch Ass’y
Idler Arm Ass’y
Capstan Shaft

Tape Running
Guide Post

Cylinder Unit

: Clean
: Check it and if necessary, replace it.

500

hours

1,000
hours

1,500
hours

2,000
hours

2,500
hours

Notes

Clean those parts in
contact with the tape.

Clean the rubber, and parts
which the rubber touches.

Replace when rolling
becomes abnormal.

Clean the Head

CONFIRMATION OF HOURS USED

POWER ON total hours and PLAY/REC total hours can be checked on the screen.
Total hours are displayed in 16 system of notation.

NOTE: If you set a factory initialization, the total hours is reset to "0".

The confirmation of using hours will not be possible if clock has been set. To reset clock, either unplug AC cord
and allow at least 5 seconds before Power On.

1.

Set the VOLUME to minimum.

2.

Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 2 seconds.

3.

After the confirmation of using hours, turn off the power.

INIT 00 08

POWER ON 0010

PLAY/REC 0003

(16 x 16 x 16 x thousands digit value) + (16 x 16 x hundreds digit value) + (16 x tens digit value) + (ones digit value)

Initial setting content of MEMORY IC.
POWER ON total hours.

PLAY/REC total hours.

C3-1

PREVENTIVE CHECKS AND SERVICE INTERVALS

CLEANING

NOTE

After cleaning the heads with isopropyl alcohol, do not
run a tape until the heads dry completely. If the heads
are not completely dry and alcohol gets on the tape,
damage may occur.

1. AUDIO CONTROL HEAD

Clean the Audio Control Head with the cotton stick
soaked by alcohol. Clean the full erase head in the
same manner. (Refer to the figure below.)

2. TAPE RUNNING SYSTEM

When cleaning the tape transport system, use the
gauze moistened with isopropyl alcohol.

3. CYLINDER

Wrap a piece of chamois around your finger. Dip it in
isopropyl alcohol. Hold it to the cylinder head softly.
Turn the cylinder head counterclockwise to clean it (in
the direction of the arrow). (Refer to the figure below.)

NOTE

Do not exert force against the cylinder head. Do not move
the chamois upward or downward on the head.
Use the chamois one by one.

Audio Control Head

Cylinder Head

C3-2

WHEN REPLACING EEPROM (MEMORY) IC

If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to
ensure correct data settings while making reference to TABLE 1.

NOTE: No need setting for after INI 35 due to the adjustment value.

+0 +1 +2 +3 +4 +5 +6 +7 +8 +9
08 0A 70 6B C2 B3 24 A9 51 2E

10

B2 92 93 00 1A 30 25 08 80

9A

00 3A 10 25 54 60 23 3B DA D7

20 00 00 00 00 00 38

+A

+B +C +D +E +FINI
40 A6 00 40 00 1000
A9 0F 94 43 06 14

88 08 88 98 88 0630

Table 1

Enter DATA SET mode by setting VOLUME to minimum.

1.
Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 2 seconds.

2.
ADDRESS and DATA should appear as FIG 1.

ADDRESS DATA

INIT 00 08

POWER ON 0010

PLAY/REC 0003

Fig. 1

3.

ADDRESS is now selected and should "blink". Using the VOL. +/- button on the remote, step through the ADDRESS until
required ADDRESS to be changed is reached.

4.

Press ENTER to select DATA. When DATA is selected, it will "blink".

5.

Again, step through the DATA using VOL. +/- button until required DATA value has been selected.

6.

Pressing ENTER will take you back to ADDRESS for further selection if necessary.

7.

Repeat steps 3 to 6 until all data has been checked.

8.

When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input.

After the data input, set to the initializing of shipping.

9.

Turn POWER on.

10.

Press both VOL. DOWN button on the set and Channel button (1) on the remote control for more than 2 seconds.

11.

After the finishing of the initializing of shipping, the unit will turn off automatically.

The unit will now have the correct DATA for the new MEMORY IC.

C4-1

SERVICING FIXTURES AND TOOLS

Alignment Tape

Back tension cassette gauge

Torque cassette gauge

Taper nut driver

(KT-300NR)

ST-N5
ST-NF

70909103

70909199

70909228

VTR cleaning kit VTR lubrication kit Grease JG002B

JG002E
JG002F

JG022 Master Plane JG024A Reel Disk Height

Adjustment Jig

JG153 X Value Adjustment

Screwdriver

JG154 Cable

Adapter
Dial Torque Gauge
(10~90gf•cm)
(60~600gf•cm)

JG180 AV Jack Jig

Part No.Ref. No. Parts Name

JG002B
JG002E
JG002F

JG024A APJG024A00 Reel Disk Height Adjustment Jig Reel Disk Height Adjustment

JG153 APJG153000 X Value Adjustment Screwdriver X Value Adjustment
JG154 APJG154000 Cable Used to connect the test point of SERVICE and GROUND

JG180 APJG180000 AV Jack Jig PG Shifter Adjustment
JG185 APJG185000 Tentelometer Confirmation of Tape Tension on Playback

APJG002B00
APJG002E00
APJG002F00
APJG022000JG022 Master Plane Reel Disk Height Adjustment

JG185 Tentelometer

Adapter
Dial Torque Gauge (10~90gf•cm)
Dial Torque Gauge (60~600gf•cm)

Remarks

VSR Torque, Brake Torque (S Reel/T Reel Ass'y)
Brake Torque (T Reel Ass'y)
VSR Torque, Brake Torque (S Reel)

PREPARATION FOR SERVICING

How to use the Servicing Fixture

1.

Remove the Syscon PCB from the set.
Be sure to place the parts on a paper so that they have no short-circuit each other.

2.

Short circuit between TP1001 and Ground with the cable JG154.
(The BOT, EOT, and the Reel Sensor do not work and the deck can be operated without a cassette tape.)

3.

In case of using a cassette tape, press the STOP/EJECT button to insert or eject a cassette tape.
Turn on the power and re-check the cable before checking the trouble points.

D1-1

MECHANICAL ADJUSTMENTS

1. CONFIRMATION AND ADJUSTMENT

Read the following NOTES before starting work.

• Place an object which weighs between 450g~500g on the

Cassette Tape to keep it steady when you want to make
the tape run without the Cassette Holder. (Do not place an
object which weighs over 500g.)

CONFIRMATION AND ADJUSTMENT OF REEL

1-1:

DISK HEIGHT

1.

Turn on the power and set to the STOP mode.

2.

Set the master plane (JG022) and reel disk height
adjustment jig (JG024A) on the mechanism framework,
taking care not to scratch the drum, as shown in Fig. 1-1-
A.

3.

While turning the reel and confirm the following points.
Check if the surface "A" of reel disk is lower than the
surface "B" of reel disk height adjustment jig (JG024A)
and is higher than the surface "C". If it is not passed,
place the height adjustment washers and adjust to 10(+2,

-0)mm.

4.

Adjust the other reel in the same way.

Master Plane (JG022)

Reel Disk Height Adjustment Jig
(JG024A)

1-2: CONFIRMATION AND ADJUSTMENT OF TENSION

POST POSITION

1.

Set to the PLAY mode.

2.

Adjust the adjusting section for the Tension Arm position
so that the Tension Arm top is within the standard line of
Main Chassis.

3.

While turning the S Reel clockwise, confirm that the edge
of the Tension Arm is located in the position described
above.

Standard line of Main Chassis

Tension Arm

0.5mm (Adjusting range)

Adjusting section for the
Tension Arm position

Tension Band

Fig. 1-2-A

Master Plane (JG022)

10(+0.2, -0)mm

Reel Disk

Height Adjustment
Washer

2.6x4.7xT0.13

2.6X4.7xT0.25

Reel Disk Height
Adjustment Jig
(JG024A)

(B)

(A)

Fig. 1-1-A

(C)

Fig. 1-1-B

The Tension Arm top will
move to the inside direction
of the Main Chassis.

Bend

The Tension Arm top will
move to the outside direction
of the Main Chassis.

Fig. 1-2-B

1-3: CONFIRMATION OF PLAYBACK TORQUE AND

BACK TENSION TORQUE DURING PLAYBACK

Load a video tape (T-120) recorded in standard speed

1.
mode. Set the unit to the PLAY mode.
Install the tentelometer (JG185) as shown in Fig. 1-3.

2.
Confirm that the meter indicates 20 ± 2gf in the beginning
of playback.

• USING A CASSETTE TYPE TORQUE TAPE (KT-300NR)

1.

After confirmation and adjustment of Tension Post
position (Refer to item 1-2), load the cassette type torque
tape (KT-300NR) and set to the PLAY mode.

2.

Confirm that the right meter of the torque tape indicates
50~90gf•cm during playback in SP mode.

3.

Confirm that the left meter of the torque tape indicates
25~40gf•cm during playback in SP mode.

Tentelometer
(JG185)

Video Tape

D2-1

P1 Post

Guide Roller

Fig. 1-3

MECHANICAL ADJUSTMENTS

1-4: CONFIRMATION OF VSR TORQUE

Install the Torque Gauge (JG002F) and Adapter (JG002B)

1.
on the S Reel. Set to the Picture Search (Rewind) mode.

(Refer to Fig.1-4-B)

Then, confirm that it indicates 120~180gf•cm.

2.

NOTE

Install the Torque Gauge on the reel disk firmly. Press the
REW button to turn the reel disk.

1-5: CONFIRMATION OF REEL BRAKE TORQUE

(S Reel Brake) (Refer to Fig. 1-4-B)

Once set to the Fast Forward mode then set to the Stop

1.
mode. While, unplug the AC cord when the Pinch Roller
Block is on the position of Fig. 1-4-A.
Move the Idler Ass'y from the S Reel.

2.
Install the Torque Gauge (JG002F) and Adapter

3.

(JG002B) on the S Reel. Turn the Torque Gauge
(JG002F) clockwise.

Then, confirm that it indicates 60~100gf•cm.

4.

(T Reel Brake) (Refer to Fig. 1-4-B)

Once set to the Fast Forward mode then set to the Stop

1.
mode. While, unplug the AC cord when the Pinch Roller
Block is on the position of Fig. 1-4-A.
Move the Idler Ass'y from the T Reel.

2.
Install the Torque Gauge (JG002E) and Adapter

3.

(JG002B) on the T reel. Turn the Torque Gauge
(JG002E) counterclockwise.

Then, confirm that it indicates 30~50gf•cm.

4.

The position at FF mode.

Pinch Roller Block

Stop at this position.

Cassette

The position at
STOP mode.

Capstan DD Unit

Cassette Holder Ass'y

Opener

Fig. 1-4-A

Torque Gauge/Adapter
(JG002F/JG002B)

Torque Gauge/Adapter
(JG002E/JG002B)

NOTE

If the torque is out of the range, replace the following parts.

Check item

1-4
1-5

S Reel side:

Replacement Part

Idler Ass'y/Clutch Ass'y

S Reel/Tension Band/Tension
Connect/Tension Arm Ass'y

T Reel side:

T Reel/T Brake Band//T Brake
Spring/T Brake Arm

2. CONFIRMATION AND ADJUSTMENT
OF TAPE RUNNING MECHANISM

Tape Running Mechanism is adjusted precisely at the
factory. Adjustment is not necessary as usual. When you
replace the parts of the tape running mechanism because of
long term usage or failure, the confirmation and adjustment
are necessary.

2-1: GUIDE ROLLER

Playback the VHS Alignment Tape.

1.

Connect CH-1 of the oscilloscope to TP4001 (Envelope)

2.

and CH-2 to TP1002 (SW Pulse).
Press both VOL. DOWN button on the set and the

3.

Channel button (5) on the remote control simultaneously.
Trigger with SW Pulse and observe the envelope. (Refer

4.

to Fig. 2-1-A)

When observing the envelope, adjust the Taper Nut Driver

5.

slightly until the envelope will be flat.
Even if you press the Tracking Button, adjust so that
flatness is not moved so much.
Adjust so that the A : B ratio is better than 3 : 2 as shown

6.

in Fig. 2-1-B, even if you press the Tracking Button to
move the envelope (The envelope waveform will begin to
decrease when you press the Tracking Button).
Adjust the PG shifter during playback.

7.

(Refer to the ELECTRICAL ADJUSTMENTS)

NOTE

After adjustment, confirm and adjust A/C head.

(Refer to item 2-2)

CH-1
Envelope
(TP4001)

CH-1

CH-2

Track
CH-2
SW Pulse (TP1002)

Track

S Reel

T Reel

Fig. 1-4-B

D2-2

Max

Entrance

A

B

A : B ≥ 3 : 2

Fig. 2-1-A

Exit

Max

Fig. 2-1-B

MECHANICAL ADJUSTMENTS

2-2:

CONFIRMATION AND ADJUSTMENT OF AUDIO/
CONTROL HEAD

When the Tape Running Mechanism does not work well,
adjust the following items.

1.

Playback the VHS Alignment Tape.

2.

Confirm that the reflected picture of stamp mark is
appeared on the tape prior to P4 Cap as shown in Fig. 2-
2-A.

When the reflected picture is distorted, turn the screw

a)

1 clockwise until the distortion is disappeared.
When the reflected picture is not distorted, turn the

b)

screw 1 counterclockwise until little distortion is
appeared, then adjust the a).

3.

Turn the screw 2 to set the audio level to maximum.

4.

Confirm that the bottom of the Audio/ Control Head and
the bottom of the tape is shown in Fig. 2-2-C.

When the height is not correct, turn the screw 3 to

c)

adjust the height. Then, adjust the 1~3 again.

Audio/Control Head

Reflected picture of
Stamp Mark

P4 Cap

2-3: TAPE RUNNING ADJUSTMENT

(X VALUE ADJUSTMENT)

Confirm and adjust the height of the Reel Disk.

1.

(Refer to item 1-1)

Confirm and adjust the position of the Tension Post.

2.

(Refer to item 1-2)

Adjust the Guide Roller. (Refer to item 2-1)

3.
Confirm and adjust the Audio/Control Head.

4.

(Refer to item 2-2)

Connect the connector of AV Jack Jig (JG180) to

5.
CP1003.
Connect CH-1 of the oscilloscope to TP1002, CH-2 to

6.
TP4001 and CH-3 to Hot side of JG180 Audio out Jack.
Playback the VHS Alignment Tape.

7.
Press both VOL. DOWN button on the set and the

8.
Channel button (5) on the remote control simultaneously.
Set the X Value adjustment driver (JG153) to the 4 of

9.
Fig. 2-2-B. Adjust X value so that the envelope waveform
output becomes maximum. Check if the relation between
Audio and Envelope waveform becomes (1) or (2) of Fig.
2-3.

Envelope

Audio/Control Head

3

2

Audio/Control Head

Tape

Stamp Mark

(1)
CH-3
Audio

(2)

Fig. 2-3

Fig. 2-2-A

1

4

Fig. 2-2-B

0.25±0.05mm

Fig. 2-2-C

D2-3

MECHANICAL ADJUSTMENTS

3. MECHANISM ADJUSTMENT PARTS LOCATION GUIDE

3

4

5

6

2

1

8910

1. Tension Connect

2. Tension Arm

3. Guide Roller

4. Audio/Control Head

5. X value adjustment driver hole

6.

P4 Post

7.

T Brake Spring

8.

T Reel

9.

S Reel

10.

Adjusting section for the Tension Arm position

7

D2-4

ELECTRICAL ADJUSTMENTS

1. BEFORE MAKING ELECTRICAL
ADJUSTMENTS

Read and perform these adjustments when repairing the
circuits or replacing electrical parts or PCB assemblies.

CAUTION

•

Use an isolation transformer when performing any
service on this chassis.

•

Before removing the anode cap, discharge electricity
because it contains high voltage.

•

When removing a PCB or related component, after
unfastening or changing a wire, be sure to put the wire
back in its original position.

•

When you exchange IC and Transistor for a heat sink,
apply the silicon grease on the contact section of the
heat sink. Before applying new silicon grease, remove all
the old silicon grease. (Old grease may cause damages
to the IC and Transistor.)

Prepare the following measurement tools for electrical
adjustments.

Oscilloscope

1.
Digital Voltmeter

2.
Pattern Generator

3.

On-Screen Display Adjustment

Set the volume level to minimum.

1.
Press both VOL. DOWN button on the set and the

2.
Channel button (9) on the remote control for more than
2 seconds to appear the adjustment mode on the
screen as shown in Fig. 1-1.

TV

00 OSD 16

Fig. 1-1

Use the Channel UP/DOWN button or Channel button

3.
(0-9) on the remote control to select the options shown
in Fig. 1-2.
Press the MENU button on the remote control to end

4.
the adjustments.

FUNCTION

NO.

00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15

OSD H
CUT OFF
RF AGC
V.VCO
H.VCO
H.PHAS
V.SIZE
V.SFT
R.DRV
B.DRV
R CUT OFF
G CUT OFF
B CUT OFF
BRI.CENT
BRI.MAX
BRI.MIN

NO.

16
17
18
19
20
21
22
23
24
25
26
27
28
29

FUNCTION

CONT.CENT
CONT.MAX
CONT.MIN
COL.CENT
COL.MAX
COL.MIN
TINT
SHARP
FM.LVL
LVL
SEP1
SEP2
T.MONO
T.STE

Fig. 1-2

2. BASIC ADJUSTMENTS
(VCR SECTION)

2-1: PG SHIFTER

1.

Connect the connector of AV Jack Jig (JG180) to
CP1003.

2.

Connect CH-1 on the oscilloscope to TP1002 and CH-2
to Hot side of JG180 Video out Jack.

3.

Playback the alignment tape.

4.

Press both VOL.DOWN button on the set and the
Channel button (5) on the remote control simultaneously
to set tracking to center.

5.

Press the VOL. DOWN button on the set and the
channel button (3) on the remote control simultaneously
until the indicator REC disappears. If the indicator REC
disappears, adjustment is completed.

(If the above adjustments doesn't work well:)

6.

Press the VOL. DOWN button on the set and the
channel button (3) on the remote control simultaneously
until the indicator REC disappears.

7.

When the REC indicator is blinking, press both VOL.
DOWN button on the set and the channel button (4) on
the remote control simultaneously and adjust the

8.

Tracking +/- button until the arising to the down of Head
Switching Pulse becomes 6.5 ± 0.5H.

(Refer to Fig. 2-1-A, B)

9.

Press the Tracking Auto button.

CH-2

D3-1

6.5H

CH-1

Fig. 2-1-A

ELECTRICAL ADJUSTMENTS

CH-2

CH-1

6.5H

Fig. 2-1-B

2-2: VCO FREERUN

1.

Receive the VHF HIGH (63dB).

2.

Place the set with Aging Test for more than 10 minutes.

3.

Connect the digital voltmeter between the pin 5 of
CP351 and the pin 1 (GND) of CP351.

4.

Activate the adjustment mode display of Fig. 1-1 and
press the channel button (03) on the remote control to
select "V.VCO".

5.

Press the VOL. UP/DOWN button on the remote control
until the digital voltmeter is 2.5V.

6.

After the 2.5V adjustment, countdown the VIF VCO step
No. by 1 step with the VOL. DOWN button.

2-3: RF AGC

1.

Receive the VHF HIGH (63 ± 1dB).

2.

Connect the digital voltmeter between the pin 5 of
CP351 and the pin 1 (GND) of CP351.

3.

Activate the adjustment mode display of Fig. 1-1 and
press the channel button (02) on the remote control to
select "RF AGC".

4.

Press the VOL. UP/DOWN button on the remote control
until the digital voltmeter is 2.7 ± 0.05V.

(TV SECTION)

2-4: CONSTANT VOLTAGE

1.

Using the remote control, set the brightness and contrast
to normal position.

2.

Connect the digital voltmeter to TP601 (R520).

3.

Set condition is AV MODE without signal.

4.

Adjust the VR502 until the digital voltage is 135 ± 0.5V.

2-5: CUT OFF

1.

Adjust the unit to the following settings.
R CUT OFF=127, G CUT OFF=127, B CUT OFF=127,
SUB BRI.CENT=127, SUB CONT.MAX=100

2.

Place the set with Aging Test for more than 15 minutes.

3.

Set condition is AV MODE without signal.

4.

Using the remote control, set the brightness and
contrast to normal position.

5.

Activate the adjustment mode display of Fig. 1-1 and
press the channel button (01) on the remote control to
select "CUT OFF".

6.

Adjust the Screen Volume until a dim raster is obtained.

2-6: WHITE BALANCE
NOTE: Adjust after performing CUT OFF adjustment.

1.

Place the set with Aging Test for more than 15 minutes.

2.

Receive the gray scale pattern.

3.

Using the remote control, set the brightness and
contrast to normal position.

4.

Activate the adjustment mode display of Fig. 1-1 and
press the channel button (10) on the remote control to
select "R CUT OFF".

5.

Using the VOL. UP/DOWN button on the remote
control, adjust the R CUT OFF.

6.

Press the CH. UP/DOWN button on the remote control
to select the "R DRIVE", "B DRIVE", "G CUT OFF" or
"B CUT OFF".

7.

Adjust the VOL. UP/DOWN button on the remote
control, adjust the R DRIVE, B DRIVE, G CUT OFF or
B CUT OFF at each step tone sections equally.

8.

Perform the above adjustments 6 and 7 until the white
color is looked like a white.

2-7: FOCUS

1.

Receive the monoscope pattern.

2.

Using the remote control, set the brightness and
contrast to normal position.

3.

Turn the Focus Volume fully counterclockwise once.

4.

Adjust the Focus Volume until picture is distinct.

2-8: HORIZONTAL PHASE

1.

Receive the monoscope pattern.

2.

Using the remote control, set the brightness and
contrast to normal position.

3.

Activate the adjustment mode display of Fig. 1-1 and
press the channel button (05) on the remote control to
select "H PHAS".

4.

Press the VOL. UP/DOWN button on the remote control
until the SHIFT quantity of the OVER SCAN on right
and left becomes minimum.

2-9: VERTICAL SHIFT

1.

Receive the monoscope pattern.

2.

Using the remote control, set the brightness and
contrast to normal position.

3.

Activate the adjustment mode display of Fig. 1-1 and
press the channel button (07) on the remote control to
select "V SFT".

4.

Check if the step No. V. SHIFT is "03".

5.

Adjust the VR401 until the horizontal line becomes fit to
the notch of the shadow mask.

2-10: VERTICAL SIZE

1.

Receive the monoscope pattern.

2.

Using the remote control, set the brightness and
contrast to normal position.

3.

Activate the adjustment mode display of Fig. 1-1 and
press the channel button (06) on the remote control to
select "V SIZE".

4.

Press the VOL. UP/DOWN button on the remote
control until the SHIFT quantity of the OVER SCAN
on upside and downside becomes 10 ± 2%.

D3-2

ELECTRICAL ADJUSTMENTS

2-11: SUB BRIGHTNESS

1.

Receive the monoscope pattern. (RF Input)

2.

Using the remote control, set the brightness and
contrast to normal position.

3.

Activate the adjustment mode display of Fig. 1-1 and
press the channel button (13) on the remote control to
select "BRI.CENT".

4.

Press the VOL. UP/DOWN button on the remote
control until the white 10% is starting to be visible.

5.

Receive the monoscope pattern. (Audio Video Input)

6.

Press the INPUT SELECT button on the remote control
to set to the AV mode. Then perform the above
adjustments 2~4.

2-12: SUB CONTRAST MAX

1.

Activate the adjustment mode display of Fig. 1-1 and
press the channel button (17) on the remote control to
select "CONT.MAX".

2.

Press the VOL. UP/DOWN button on the remote
control until the contrast step No. becomes "65".

3.

Receive a broadcast and check if the picture is normal.

4.

Press the INPUT SELECT button on the remote control
to set to the AV mode. Then perform the above
adjustments 1~3.

2-13: SUB TINT

1.

Receive the color bar pattern. (RF Input)

2.

Using the remote control, set the brightness, contrast,
color and tint to normal position.

3.

Connect the oscilloscope to TP801.

4.

Activate the adjustment mode display of Fig. 1-1 and
press the channel button (22) on the remote control to
select "TINT".

5.

Press the VOL. UP/DOWN button on the remote control
until the section "A" becomes a straight line.

(Refer to Fig. 2-2)

6.

Receive the color bar pattern. (Audio Video Input)

7.

Press the INPUT SELECT button on the remote control
to set to the AV mode. Then perform the above
adjustments 2~5.

2-14: SUB COLOR

1.

Receive the color bar pattern. (RF Input)

2.

Using the remote control, set the brightness, contrast,
color and tint to normal position.

3.

Connect the oscilloscope to TP803.

4.

Activate the adjustment mode display of Fig. 1-1 and
press the channel button (19) on the remote control to
select "COL.CENT".

5.

Adjust the VOLTS RANGE VARIABLE knob of the
oscilloscope until the range between white 100% and
0% is set to 4 scales on the screen of the oscilloscope.

6.

Press the VOL. UP/DOWN button on the remote control
until the red color level is adjusted to 110 ± 10% of the
white level. (Refer to Fig. 2-3)

7.

Receive the color bar pattern. (Audio Video Input)

8.

Press the INPUT SELECT button on the remote control
to set to the AV mode. Then perform the above
adjustments 2~6.

White 0%

100%

White 100%

2-15: OSD HORIZONTAL

1.2.Activate the adjustment mode display of Fig. 1-1.
Press the VOL. UP/DOWN button on the remote control
until the difference of A and B becomes minimum.

(Refer to Fig. 2-4)

Red Level

Fig. 2-3

"A"

Fig. 2-2

D3-3

00 OSD 16

A

TV

B

Fig. 2-4

ELECTRICAL ADJUSTMENTS

2-16: SUB SHARPNESS

1.

Activate the adjustment mode display of Fig. 1-1 and
press the channel button (23) on the remote control to
select "SHARP".

2.

Check if the step No. of SHARPNESS is "40".

3.

Press the INPUT SELECT button on the remote control
to set to the AV mode. Then perform the above
adjustments 1~2.

2-17: H VCO

1.

Activate the adjustment mode display of Fig. 1-1 and
press the channel button (04) on the remote control to
select "H VCO".

2.

Check if the step No. of H VCO is "04".

D3-4

ELECTRICAL ADJUSTMENTS

3.PURITY AND CONVERGENCE
ADJUSTMENTS

NOTE

1.

Turn the unit on and let it warm up for at least 30
minutes before performing the following adjustments.

2.

Place the CRT surface facing east or west to reduce the
terrestrial magnetism.

3.

Turn ON the unit and demagnetize with a Degauss Coil.

3-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT)

1.

Tighten the screw for the magnet. Refer to the adjusted
CRT for the position. (Refer to Fig. 3-1)
If the deflection yoke and magnet are in one body,
untighten the screw for the body.

2.

Receive the green raster pattern from the color bar
generator.

3.

Slide the deflection yoke until it touches the funnel side
of the CRT.

4.

Adjust center of screen to green, with red and blue on
the sides, using the pair of purity magnets.

5.

Switch the color bar generator from the green raster
pattern to the crosshatch pattern.

6.

Combine red and blue of the 3 color crosshatch pattern
on the center of the screen by adjusting the pair of 4
pole magnets.

7.

Combine red/blue (magenta) and green by adjusting the
pair of 6 pole magnets.

8.

Adjust the crosshatch pattern to change to white by
repeating steps 6 and 7.

3-2: PURITY
NOTE

Adjust after performing adjustments in section 3-1.

1.

Receive the green raster pattern from color bar
generator.

2.

Adjust the pair of purity magnets to center the color on
the screen.
Adjust the pair of purity magnets so the color at the
ends are equally wide.

3.

Move the deflection yoke backward (to neck side)
slowly, and stop it at the position when the whole screen
is green.

4.

Confirm red and blue colors.

5.

Adjust the slant of the deflection yoke while watching
the screen, then tighten the fixing screw.

DEFLECTION YOKE
DEFLECTION YOKE SCREW
MAGNET SCREW

3-3: STATIC CONVERGENCE
NOTE

Adjust after performing adjustments in section 3-2.

1.

Receive the crosshatch pattern from the color bar
generator.

2.

Combine red and blue of the 3 color crosshatch pattern
on the center of the screen by adjusting the pair of 4
pole magnets.

3.

Combine red/blue (magenta) and green by adjusting the
pair of 6 pole magnets.

3-4: DYNAMIC CONVERGENCE
NOTE

Adjust after performing adjustments in section 3-3.

1.2.Adjust the differences around the screen by moving the
deflection yoke upward/downward and right/left.

(Refer to Fig. 3-2-a)

Insert three wedges between the deflection yoke and
CRT funnel to fix the deflection yoke.

(Refer to Fig. 3-2-b)

R G B

R
G
B

UPWARD/DOWNWARD SLANT RIGHT/LEFT SLANT

WEDGE

WEDGE POSITION

R
G
B

Fig. 3-2-a

WEDGE

WEDGE

Fig. 3-2-b

R G B

6 POLE MAGNETS
4 POLE MAGNETS
PURITY MAGNETS

Fig. 3-1

D3-5

ELECTRICAL ADJUSTMENTS

4. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE (WIRING CONNECTION)

CRT

L503

CP351

CP502

TU601

FB401

SPEAKER

AC IN

TP1002

TP1001

CP1003

CP352

TP4001

VR502

A/C HEAD

TP601

R520

CP4002

VR401

CP401

CRT

CP851A

CP801

CRT

TP801

TP803

S801

CP851B

J801

CRT PCB

SYSCON PCB

D3-6

CP354

SPEAKER

MICON/

IN/OUT/AV

AT+5V_BACK UP

Y/C/AUDIO/

HEAD AMP

SCL

SDA

AT+12V

TU_AUDIO

TU_VIDEO

Y/C_AUDIO

Q601

BUFFER

CHROMA/IF IC
IC601 M61250FP

53

42 32

58

TV BLOCK DIAGRAM

Q602, Q603

REG.

Q606

REG.

47

Q604, Q605

REG.

28

49

54

AT+12V

UNREG+8V

V. OUTPUT IC
IC401 AN5522

THERMAL

PROTECTION

AMP

PUMP
UP

VCC

1

3

2

Q607

H-CONTROL

7

5

Q405

H-DRIVE

Q406

H. OUTPUT

H_CTL

MICON/
IN/OUT/AV

DY

MICON/

IN/OUT/AV

L503

DEGAUSS COIL

AC IN

TU601

1
4

5

11

X-RAY

X-RAY_TEST

2

2

1

1

F501

Q507

FEED BACK

SW.

VR502

+B ADJ

SAW FILTER
CF601

1

Q404

SW.

Q403

SW.

TH501

FEED BACK

34

D518, D520,
D521, D530

RECTIFIER

IC502
TLP621(GR)

59

RF AGC OUT

63

VIF IN (1)

64

VIF IN (2)

2

AFT OUT

Q511

SWITCHING

Q510

SWITCHING

EXT AUDIO IN

T501

8

11
13
14

16

5

3

VREG VCC

VIF VIDEO OUT

X' TAL

34

X602

3.579545MHz

IC501
KIA78R05API

5V REG IC

8.7V REG OUT

AT 5.7V REG OUT

FBP IN

INV FBP OUT

10

19

AT+12V

UNREG+8V

AUDIO OUT

FAST BLK

P.CON 5.7V REG

V RAMP FEED BACK

FM DIRECT OUT

POWER ON CONT

V PLUSE OUT

H OUT

11

Q505

POWER_FAIL

SDA

SCL

R OUT
G OUT
B OUT

V OUT

B IN

R IN

G IN

Q508

PROTECT SW

P. CON+5V

51
26

27
24
14

15
16

20

21
23

22

FB401

COL
+B

E180
ABL
AFC
HEA

E180V

3

HV

F
S

J801
F

7

11

8
6

V801

CRT

1
2
6
7

9

10

5

Q804

BLUE AMP

6

Q806

RED AMP

Q805

GREEN

AMP

Q609, Q611

ACL_CANCEL

Q612

CUT OFF SW

VD

PROTECT

Y/C/AUDIO/
HEAD AMP

VD
HD

OSD_BLK

MICON/
IN/OUT/AV

OSD_B
OSD_R
OSD_G

AFT_M

Q503

PROTECT

DRIVE

SOUND AMP IC
IC351 AN7511

2

5

6

8

2
7
1

HEADPHONE JACK
J351

SP353
SPEAKER

4

1

SP351
SPEAKER

POWER_FAIL 2

VCR_POWER-H
TV_POWER-H

MICON/
IN/OUT/AV

TV_A_MUTE

E-1

E-2

TV

FE HEAD

CYL

VD

CP4003

1

CP4001

1

SP-CH2 (L)

2
3

SP_COM
SP-CH1 (R)

4

AE_HEAD (-)

GND2

Y/C/AUDIO/HEAD AMP IC
IC4001
LA71206M-MPB

NC

NC

67

66

65
72

73
74

9

P

R

P
P

R

P

REC AMP

7

8

AUTO BIAS

6

X4001

3.579545MHz

50

VX01

L

H

H

L

VREF

Q4012

49

EQ

AMP

Y/C/AUDIO/HEAD AMP BLOCK DIAGRAM

BUFFER

41

C-LPF

PB.EE

PLL

3.58M
BPF2

Main
CONV

ACC
DET

LINE
AMP

MUTE

B-UP
AMP

3.58M
BPF1

REC
APC

RP

LPF

REC
APC

AGC

NYR/COMB

TIMMING

DRIVER

R
P

CLAMP

ALC

37

34

CLAMP AUTO-BIAS

CCD

VCA

VIDEO
AGC

1
2
3

QV-QH

123

Q4010

BUFFER

OUT

SYNC
SEP

SYNC
SEP

SERAIL
DECODER

C-ROT

RF-SW IN

AUDIO

MUTE HA SW

ENV DET

60B

5
3

54
55

36
39
57
58
59

24
26
25

Q4009

BUFFER

Q4007

SYNC IN

Y/C_CLK

Y/C_DATA

Y/C_CS

H. SW
VCR_A_MUTE
ENV. DET

V.REC_ST-H

DUMMY_V. SYNC
SD_VIDEO

SD_SYNC

MICON/
IN/OUT/AV

MICON/
IN/OUT/AV

11

CP4002

6

AUDIO REC

5

HEAD

AUDIO

CONTROL

E-3 E-4

AUDIO PB

4

CTL+

3

CTL-

2

AE HEAD(+)
AE HEAD(-)

1

COIL, BIAS OSC
T4001

5

6

4

Q4001, Q4002

AUDIO PB

SW.

Q4005

2

3

BIAS CTL

Q4006

BIAS OSC

1

Q4003

3

SW

5

4

P. CON + 5V

2

10

80

76

32

30

NC

28

TU_VIDEO

TU_AUDIO

Y/C/AUDIO

FRONT_VIDEO

FRONT_AUDIO

CTL+
CTL-

TV

MICON/
IN/OUT/AV

TV

CAPSTAN
DD UNIT

P. CON+5V

X-RAY_TEST

VCR_POWER_H

CP1001

1

CAP_FG

4

CAP/M F/R

5

I LIMIT

CAP_CTL

9

10

LDM_CTL

11

CTL_FG/PG

CYL_CTL

12

TV

PROTECT

AT+5V

AT+5V

X_RAY

H_CTL

Q1014

X-RAY

Q1013

EOT SENSOR

Q1011

BOT SENSOR

SW1001

14
2

3

4

1

3

2

3

1

4

2

MS_SEN A

Q1009

MS_SEN B

Q1003

REEL SENS.

Q1005

MICON/IN/OUT/AV BLOCK DIAGRAM

TIMER SYSCON MICON IC
IC1001 OEC7107A

TAB SW

50

1

MSSEN-A

MSSEN-B

2

REEL-T

80

41

X-RAY_TEST

27

VCR-POWER

87

CAP- FG

11

CAP-FWD
CAP-LIMIT

12
76

CAP-PWM

20

LDM CTL

90

DRUM FG/PG

DRUM-PWM

77

X_RAY

21

24 H CONTROL

25

PROTECT

3

EOT

4

BOT

POWER_FAIL_L

X-OUT(12MHz)

XC-OUT(32KHz)

DUMMY-V.SYNC

V REC START H

RESET-L

X-IN(12MHz)

XC-IN(32MHz)

CTL+

CTL-

CVIN

VIDEO-H. SW

SCLK

CS

VIDEO ENV

VCR_A_MUTE

IIC-DATA1

IIC-CLK1

CTL AMP-OUT

FF/REW-L

AFT(MONI)
OSD OUT1

V-SYNC

H/C-SYNC

KEY 1

OUT

34

85
39

38
36

35
13
95

94
66

56

18
68SDATA
70

73

6

81

72

71

97

FF/REW_SW

84

R

64

G

63
62

B

7
60
59
58

30TV_POWER

82TV_A_MUTE

9

1

X1001
12MHz

X1002

32.768KHz

Q1004

SYSTEM RESET IC
IC1003
XC61CN3102SR

SDA

5

SCL

6

EEP ROM IC
IC1099
S-24C04BDP-LA

J4202

J4201

POWER FAIL2

2

4

FRONT_AUDIO

FRONT_VIDEO

DUMMY_V.SYNC
CTL+
CTL­V. REC_ST_H

SD_VIDEO
SD_SYNC

H. SW

Y/C_DATA

Y/C_CLK

Y/C_CS

ENV_DET

VCR_A_MUTE

SDA
SCL

OSD_R
OSD_G
OSD_B

AFT_M
OSD_BLK

VD

HD

TV_POWER_H
TV_A_MUTE

TV

Y/C/AUDIO/
HEAD AMP

TV

KEY 2

REMOCON-IN

T-REC LED

REC LED

10

14
29

28

T-REC/PLAY

LED SW

Q4202

Q1007

REC LED

SW(AI)

POWER
ON/OFF

OS2201

REC
D1013

REC/OTR STOP/EJECT PLAY

321

CH DOWN

T-REC
D1004

CH UP VOL. UP VOL. DOWN

FF/CUE REW/REV

AT+5V

E-5 E-6

CD853

C4211

SW2209 SW2210

SW2202

OS2201

C382

SW2205 SW2206

SW2204 SW2208

SW2201

J351

C380

J4202 J4201

SW2203

SW2207

D1013

CP354

C381

D1004

W242

SW1001

W260

R380

C1021

D1002

D2201

R381

R1051

C1003_1

D608

R1018_1

R1056

C1053

W251

Q602

W250

W221

W219
W218

W245

L801

C643

W220

W244

C1058

W801

W241

W249

Q804

W216

W213

W230

X1001

W240

W238

W263

W261

W258
W256

W252

Q805

R816_1

Q1003

Q603

W235

W233

W227

W225

W239

W237

C805

W223

X1002

W262

TP803

W222

W267

W217
W128

W234

W231

L1001

W254

Q806

CP851B

Q1005

W232

W257

R810

Q1009

W125

W228

W226

W243

IC1099

W255

R808_1

R820_1

R1050

W236

W264

W246

W247

W113

W111

W168

W187

W266

TP801

TP802

C801_1
S801

W119

W169

W164

W159

W259

CC002

W805

R1010

W108

W146

W170

W102

W157

W178

W156

W183

R807

C620

W149

W182

W211

R802

W105

W133

W145

W190

W174

W210

R805

W132

W148

W194

W196

W127

W114

W143

C1020

W181

W104

W129

W850

D1001

W836

W142

W180

W914

W825

W158

W141

C1015

W208

CP1003

W124

W112

W163

W126

D609

W166

W140

W179

W207

J801

W270

R650

R1016

W139

C1016

W177

W199

W195

D610

W162

W138

W192

C1018

D1014

W209

W172

W122

W161

W137

W193

PRINTED CIRCUIT BOARDS

SYSCON/CRT (INSERTED PARTS LIST)

S804

Q1011

W130

C1024

R1028

W212

W206

W197

W841

CP801

W131

D611

W160

W144

L4009

W885

W118

W147

W136

W205

S802

W167

W165

W191

W189

W176

W171

R4048

W120

W155

W188

W175

W173

W202

Q1013

W103

W121

W154

W082

C4042

W200

C665

W064

W135

W110

W075

W153

C4047

W203

TP1001

D605

W065

W152

CD852

W107

C1032

W117

W151

R4028

R4029
R4032

W080

W106

R655_1

W062

W134

W150

W066
W888

W873

W083

D4001

W077

W099

C1001

R1008

W115

C4045

W201

W057

C1007

W272

W852

R643_1

W073

W071

W097

W095

W892

C4053

SOLDER SIDE

D603

W813

W050

R1064

W049

W047

01

0

1

P

C

W063

L609_1

C666

B602

W061

R639_1

R627_1

R613_1

X602

W874
W072

W070

W067

C4010

W068

L4005

W094

W092

W090

C4035

C4046

C4034

C4049

C4052

X4001

CP4003

W809

C4031

C4051

W100

TP1002

TP4001

S819X

C662_1

C649

C648

D4002

C4027

C4048

W079

W098

C356_1

W814

R623

C664

W069

W812

D408

W895

W861

C659

C4030

C4058

W096

C351

S830Y

W051

W842

S822X

R668

L4003

W882

IC351

Q606

Q4006

Q4005

R4004

W085

W818

S819Y

C403

C627

CF603

C636

C652

W091

D409

W828

CF601_1

CF604
W849

C669

W269

W076

W074

C4012

C4023

W078

C4065

R612

W089

W087

C419_1

W053

W048

W060

R644_1

C641

W915

C4004

W086

W084

C4067

C4062

C355_1

W093

CP352

W865

L607

R665_1

C628_1

C4002_1

T4001

W908

C4063

W081

W101

R607

W058

W054

CP851A

W827

W268

Q4002

C4009

W088

W014

L601

C625

C644

W059

Q605

C

P

4

0

0

2

W022

Q4001

W041

CP4001_1

L4001

W834

L4006

W042

R409_1

C632

Q604

W026
W025

R4007

R4006

W829

D412

R442_1

W013
W878

R616_1

D601

C4025

W038

C542

W027

W023

W019

W043

W854

R456

W018

D602

C624_1

W024

W879

C417_1

W016

W015

W040

W039

W045

R522

C354_1

C431

W917

C534

D508

Q405

S822Y

W858

D515

C438

W030

W036

D513

W044

W857

W020

HS504

T401

C418

R651

W035

R460

HS402

D501

R512

R508

IC501

S

10

R640

R503

1A

D413

W925

W017

R402

C517_1

C511

W034

D504

C521

C522

S102A

W816

CP401

R554

W021

Q406

R553

D510_1

C519

D405

W032

CP503

R490

C432_1

R520

C524_1

W037

W936

L401_1

R521

F501 FH501FH502

W811

W830

W833

B503

D512

C516

C402

C423

C531_1

D503

D519

Q503

D505

R450_1

C

42

4_1

S826Y

W029

D502

C541_1

R536

C518

R

C422

VR401

R408_1

W028

C523_3

D507

B505

D517

C506_1

4

4

W033

R529

C505

D514

7

W001

D411

D407

W928

CF602

VR502

R533

CP504

R500

W817

R453

C451

R532

D402

W840

R449

R410

W831

L616

D528

T501

Q507

FB401

R417

D403

R505

S826X

TH501_1

D404

R419

W871

W007

C

5

30

C515_1

W838

D401

CP505

R421

W003

IC401

HS401_1

L603

R511

L502

C406

D536

D533

R517

B501

CP502

R501

W004

R534

C

R528

R509

535

C405

TU601

C612

C537_1

D535

_1

D530

IC502

D

R514

W807

C610

R

53

D534

502

7

C509

D521

C407

R415

W005

R531

R524

D518

D520

W002

W010

W009

C507

C508

CP351_1

W008

Q511

W853

Q510

R423

D410

S830X

C539

C420

HS501

F-1

CD501

F-2

PRINTED CIRCUIT BOARDS

SYSCON/CRT (CHIP MOUNTED PRTS)

SOLDER SIDE

R352

R353

C301

R359

Q1007

C510

R605

R527

C605C604

C536

C532

R525

C613

C549

C602

R504R506R510

R552_1

C554

R535

R507

R530

R516

Q505
R513

C631

R4053

R4052

C4020

R4001

C4069
R4051

C4015

C4021

C4019

C4016

R4003

R4002

Q4003

R4039

C4064

61

C4055

C4005

R4015

R4012

R4064

R4010

R4042

IC4001

C4066

C4059

41

1

R4011

C4006

R357

C4061

R4041

R4038

21

C4074

R4043

Q4012

R4055

C4028

R4020

R4017

R4018

C4060

R4035

R4060

C4032

R4021

R4019

C4029_1

R669

C654

C1042_1

R4033

R4034

R4062

R4068

C4037

C4036

R4024

C4033

R4037

R4065

R646

Q4010

C4050

R4023

R4022

C4014

C4038

C4054

C4044

C4076

R4057
R4058

R638

R4025

R4054

C4075

C4057

Q4011

R4059

C4041

Q4007

R652

R1025

Q4009

R4061

C629

R602

C675

R603

R4044

R4045

R4047
R1035

C1028

R1012

C1070

R1017
R1029

C1019

R1011

R4026

C1039_1

R1021

C1065

R1013

R1009

Q1004

C4043

R1007

C1029

C1004

C1009

C1010

R1042

Q4202

R1078

C1023

R1020

R1053

C1022

C656

R1033

C1062

C1037

C1084

R1034

C1034

R1036

R1044

R1045

R1038

C1013

C1027

R1022

C1060

C1061

R1031

C1035

C1031

C1038
C1071

81

R1048

C1025

R1063

C1056

R1032

IC1001

1

R2201

R1084
R1086

C1043

C1082

R2207

R2206

R2204

R2202

R2208

R2203

R1046

R1047

R1070

C1026

R1040

R1005

C1040

C1047

31

C1048

C1049

C1083

C1050

C1068

R1066

C1046

51

R401

R411

R416

R414

R413

Q508

R519_1

C416

C623

R444

Q404

Q601

R446

R445

R618

R628

C527

R620

C603_1

C640

R601

R657

R622

R615

C618

R609

C622

C626

C691

C634

C660

C650

R633

C651

33

R626

Q611

C639

R656

C647

R635

C1069

Q609

49

IC601

1

C637_1

R636

Q607

17

C646

R634

R625

C668_1

C645

R649

C688_1

C653_1

R631

R1001

R647

R648

C630

R667

R670

R641

R1073

R642

R660

W894

R659

R658

W843

R1054

C621

Q1014

R617

R1087

R1055

R1052

R1019

C811
R813

R1083

R663

C810
R815

R811
C809
R814

C667

W810

R812

R1049

IC1003

C1017

Q403

R2205

R4203_1

C4205

F-3

F-4

ABC D E F GH

G-1

G-2

Y/C/AUDIO/HEAD AMP SCHEMATIC DIAGRAM

8

(SYSCON PCB)

8

FROM TV POWER

7

6

5

FROM/TO CYL

4

CP4001_1 TOC-C04X-B1

4

SP-CH1 (R)

3

SP_COM

2

SP-CH2 (L)

1

3

FROM/TO HEAD AUDIO CONTROL

CP4002

IMSA-9604S-06Z14

AUDIO_REC

6

AUDIO_PB

5

4

3

AE_HEAD(+)

2

AE_HEAD(-)

1

2

TO FULL ERASE HEAD

CP4003
B2013H02-2P

2

AE_HEAD(-)

1

COMP

ENV_DET

H.AMP_SW1

100K

R4044

18K

P.CON+5V GND

GND

W858

NC

2.7K

R4051

W812

R4054

C4069

0.1 F

0.5

2.2

OUT

COMP

AUDIO

ENV
DET

KILL

616263646566676869

0

4.0

1.8

0.7

0.7

NC

0.7

NC

5.0

DET

HA

GND

CHROMA

DET

ACC

DET

HA VCC

HA SW

P

R

P

1.7

1.8

820

70717273747576777879

0

HA

PRE GND

2.0

P

2.0

2.0

2.2

4.9

2.3

NC

R

P

0

A-GND

1
2
3

A-VCC

0

2.0

Vref

2.3V

1 10111213141516

2.2 2.2 2.3 2.2 2.2 2.5 2.3 2.2 2.3 2.4 5.0 1.0 1.0 1.7 1.4 0

0.1 F

C4028

1K

C4074

C4025

R4055

0.01 F

336.3V KA

C4027

2206.3V YK

476.3V KA

W908

GND

CTL+

CTL-

HOT

GND

C4016

0.068 B

C4019

C4015

0.047 F

0.047 F

P.CON+5V

TU_AUDIO

P.CON+5V DUMMY_V.SYNC

FRONT_AUDIO P.CON+5V

L4001

22uH 0305

R4004

15 1/4W

C4055

0.1 F

C4009

C4012

226.3V KA

4716V KA

R4007

39K 1/4W

R4006

56K 1/4W

R4053

6.8K

C4023

R4052

8.2K

226.3V KA

R4064

6.8K

D4002

R4012

C4020

0.1 F

C4021

0.1 F

MTZJ13B

Y/C/AUDIO/HEAD AMP IC

W879

IC4001

LA71206M-MPB

P.CON+5V SD_SYNC

5.2
SW

0

Q4003

DTA124EKA

5.3

R4001

560

0

R4002

0.7

0

0

0.7

0

10K

R4003

10K

5

C4002_1

0.022100V MMTS

6

5

COIL,BIAS OSC

T4001

1626009

1

2

34

2206.3V KA

C4004

C4005

C4006

BIAS CTL

Q4005

L4003

KTA1266

100uH 0305

0

3.3K

0.01 F

R4010

BIAS OSC

Q4006

0

KTC3203_Y

0

2.2

R4015

0.015 B

5.20

5.2
R4011

22K

C4010

CTL+

CTL-

AUDIO PB SW

Q4001

KTC3198

AUDIO PB SW

Q4002

KTC3198

V.REC_ST_H

VCR_A_MUTE

12K

R4045

C-ROT

MUTE

RF-SW

IN

H

L

H

L

ALC

ALC
DET

SP,LP

3

4

6.8K

R4017

5.6K

R4018

R4019

330K

C4029_1

0.015 B

H.SW

Y/C_CS

Y/C_CLK

Y/C_DATA

R4047

P.CON+5V

BUFFER

Q4012

2SC2412K

12K

L4006

47uH 0305

1.8K

2

R4041

5.0

4.0

3.4

P.CON+5V

L4005

47uH 0305

476.3V KA

C4063

150V KA

C4062

C4065

C4064

0.022 B

8.2K

R4039

R4042

X4001

100CT3R502

3.579545MHz

SERAIL

DECODER

C-LPF

PB,EE

7

C4032

3.350V KA

R4057

1.2K

4.9

R4058

RP

LPF

VREF

8809

0.0047 B
R4021

27K

C4033

820PB

BUFFER

Q4011

2SC2412K

0.6

0

5.6K

Main
CONV

4.21M

CONV

BPF

Sub

C4075

C-VCC

REC

AMP

R4022

100P CH

3.58M

470

C4034

4

R4059

10M

BPF2

B-UP

AMP

LINE

MUTE

DETAIL

AMP

ENH

NL

EMPHA

R4061

320FH

VX01

VCO

P

PB

REC

APC

APC

BEFORE

P

R

AFTER

BGA

R

P

ACC

AMP

RPPP

ACC

DET

P

R

CLAMP

NL

EMPHA

FM
MOD

R-EQ

NORMAL

TEST

REC

FM-EQ

FM

R

P

AUTO
BIAS

AGC

PHASE

fo-ADJ

R4023

FM EQ

PHASE

EQ

EQ

Q-ADJ

68K

4.725V KA

R4024

C4076

10M

C-GND

+

R

P

PB,EE

EQ

REC:LP<EP

AMP

PB:EP

C4031

R4065

4.7M

1016V KA

C4030

120

R4020

R

REC
AFC

R

Y-LPF

DOUBBLE

PB

VHS

0.1 F

2.250V KA

C4066

820

SLD

BGA
BGA

PB-C

LIM

S-EQ

V.ENV

TP4001

6.8K

R4037

R4043

B

YNR/COMB

P

R

SOPB

3

NC

390

0.022

AGC

C4035

C4067

NC

B

AMP

B.D

P

3.58M
BPF1

FM

DEM

P

FM

FIL

3.3K

CNC

PB

N.L.
DEEM

NC1

R

150V KA

ALWAYS

5V

Y-GND

150V KA

R

PB-C

SUB

MAIN

DE-EM

Y/C

LPF

C4058

476.3V KA

C4059

0.1 F

R4038

680K

VDD 4Fsc

TIMMING OUT

AUTO-BIAS

DRIVER

CCD

CLAMP

VIDEO

AGC

1/2
FBC

R

P

MIX

R

P

QV/QH

SYNC

SEP

V.SYNC

SEP

R

P

4.7K

MAIN

EMPHA

DET

FIL

17 18 192 20

0 1.5

0.1 2.2

NC

C4036

390P B

C4037

W882

C4014

2.203.33.34.02.61.92.8

PLL

CLAMP

VCA

1
2

3

S

C4060

0.01 F

TO IN/OUT

C4061

0.01 F

FROM/TO MICON

W818

0.85.05.02.35.04.84.84.8000

414243444546474849550515253545556575859660

CLOCK

0

40

VSS

1.7

OUT

0

VSS

3.0

IN

2.8

VCA

3.1

3.1

2.6

VCP

2.0

4.0

REG

4V

2.0

NC

30 31 32 33 34 35 36 37 38 39

2.3

BAL
TC1

2.3

1.6

AGC
TC2

2.9

6DB

3.6

C4048

1016V KA

C4049

1016V KA

C4050

0.22 B

R4060 1.5M

C4051

336.3V KA

BUFFER

Q4010

2SA1037AK

1.7

0 2.3

R4032

100 1/4W

C4052

4.750V KA

C4053

4.750V KA

C4054

0.1 F

R4033

2.2K

R4034

82K

R4062

3.3M

C4057

1F

C4047

1016V KA

R4048

68 1/4W

R1025

100

R4035

100K

D4001 MTZJ13B

6.3V

0.1 F

C4042

C4041

W885

KA

100uH 0305

100

L4009

1

TU_VIDEO

FRONT_VIDEO

P.CON+5V

Y/C_VIDEO

SD_VIDEO

0

0.1 F

Y-VCC

B

R4025

C4038

1.5K

180P CH

4.9

C4046

2.8

1.8

21 22 23 24 25 26 27 28 29

C4044

2.2M

R4068

3.350V KA

2206.3V KA

0.1 F

C4045

0

5.0

R4029

47K 1/4W

5.0
BUFFER

Q4009

2SA1037AK

0.7

SYNC IN

Q4007

2SC2412K

W873

R4028

2.8

0

47K 1/4W

W888

R4026

39K

C4043

0.1 F

PLAYBACK LUMINANCE SIGNAL
PLAYBACK COLOR SIGNAL
RECORD LUMINANCE SIGNAL

RECORD COLOR SIGNAL
PLAYBACK VIDEO SIGNAL
TUNER VIDEO SIGNAL

AUDIO SIGNAL(PB)

AUDIO SIGNAL(REC)

0.047 B

DEFLECTION SIGNAL

FROM AV

FRONT_VIDEO

FRONT_AUDIO

Y/C_AUDIO

Y/C_VIDEO

Y/C_CLK

Y/C_DATA

Y/C_CS

V.REC_ST_H

VCR_A_MUTE

DUMMY_V.SYNC

CTL-

CTL+

H.AMP_SW1

COMP

ENV_DET

H.SW

SD_VIDEO

SD_SYNC

FROM/TO CHROMA/IF

TU_VIDEO

TU_AUDIO

SD_VIDEO

Y/C_AUDIO

VD

PCB010
VMB281

7

6

5

4

3

2

1

CAUTION: DIGITAL TRANSISTOR

NOTE:THE DC VOLTAGE EACH PART WAS

MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK.

P.CON+5V

VD

Y/C_AUDIO

NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME

OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE

1

ABC D E F GH

8

G-3

G-4

7

CP1001
TMC-J12P-B2

1

2

3

4

5

6

6

7

8

9

10

11

12

5

4

3

2

FROM TV POWER

POWER_FAIL2

FROM/TO DECK

(CP101)

CAP_FG

CAP_VCO

VCC

CAP/M/F/R

I_LIMIT

GND[M]

GND

LD/CY_VCO

CAP_CTL

LDM_CTL

CYL_FG/PG

CYL_CTL

FROM/TO DECK

CD852

CH01408A

BOT SENSOR

Q1011

ST-304L

EOT SENSOR

Q1013

ST-304L

ABC D E F GH

MICON SCHEMATIC DIAGRAM

P.CON+5V

GND

MOTOR+12V

GND

5.1

(MOTER GND)

22016V YK

C1032

W805

0

05.1

W892

C1001

R1010

3.3K 1/4W

D1001

CENTER LED

LTE-3271T-012A-O

4716V YK

R1016

270 1/4W

C1024

C1007

EOT

R1011

4706.3V YK

W914

4725V YK

R1073

330K

BOT

W836

SW1001

TAB SW

CAP_FG

CAP_M/F/R

330K

R1018_1

47K 1/4W

LSA-1144EAU

CAP_CTL

LDM_CTL

CYL_DRIVE

C1042_1

1F

C1043

0.01 B

(SYSCON PCB)

SDA

SCL

0.0068 B

R1044

3.3K

R1045

NC

NC

VOLUME

CAP-PWM

81 VCR_A_MUTE

82 TV_A_MUTE

83 (EXT MUTE)

98 AMP-VCC

99 ANALOG VCC

100 DEW

HI-FI-ENV

VIDEO-ENV

ENV_DET

3.3K

JUST CLOCK

AFT(MONI)

AFT_M

REEL SENS

RPI-303

Y/C_CS

Q1005

Y/C_CLK

Y/C_DATA

C1061 100P CH

C1060 100P CH

220

R1042

220

R1038

4.9 0 0 0

CS

AFT(REC)

9

KEY_A

REEL_T

NC

0 4.7 5.24.24.9

SCLK

IIC-CLK1

IIC-DATA1

KEY 2

KEY 1

5.2 5.2 2.22.22.41.41.4 5.2 2.3 2.6 2.6 5.2 5.2

KEY_B

C1039_1

4.7K

R1046

47K

R1019

0 1.2

1

0 0.9

SDATA

CENTER LED

CAP-FWD

DUMMY-V.SYNC

CAP-LIMIT

11 12 13 14 15 16 17 18 192 20 21 22 23 24 25 26 27 28 293 30

000

DUMMY_V.SYNC

REMOCON_IN

0.1 F
C1058

4.7K

R1047

390

R1052

2

34

C1069

D1014

VCR_A_MUTE TAB_SW

TV_A_MUTE

R1001

3.3K

IIC_OFF

R1008

CAP_FG

1K 1/4W

R1064

1K 1/4W

CTL-

CTL+

FF/REW_SW

Q1004

DTC124EKA

5.1

C1025

0.0022 B

TAB_SW VCR_POWER_H

H.SW

H.AMP_SW1

CAP_M/F/R

R1012

0

0

C1013

B

0.0039

10K

C1022

0.1 F

R1048 4.7K

13

C1084

0.0047 B

C1019

0.001 CH

C1027

0.0039 B

W894

MS_SEN B

Q1003

RPI-352C40N

5.2 5.2

0.8 1.4 0.5

CAP_CTL

C1070

R1009 560

R1013 560

10

4

R1083

R1028

0.1 B

C1020

1016V KA

IC1001

OEC7107A

33K

CYL_DRIVE

22K 1/4W

0.0033 B

MTZJ6.8B

11

C1015 4710V KA

C1016 2216V KA

C1018 4.750V KA

TIMER SYSCON MICON IC

R1070

100

23

1

R1029

4.7K

W810

NC

818283848586878889

0

REEL-T

5.1

NC

5.1
FF/REW-L

5.2
POWER_FAIL_L

5.9
IIC OFF

5.2
CAP-FG

2.5
AMP-VSS

0

NC

2.0
DRUM FG/PG

90919293949596979899

0.6
AMP-VREFOUT

2.5
AMP-VREFIN

2.5
C

0.2
CTL-

0

CTL+

2.5
AMP C

2.6
CTL AMP-OUT

2.5

5.1

5.2

100

MSSEN-A

0

110

MS_SEN-A

MS_SEN-B

MS_SEN A

Q1009

RPI-352C40N

0.8 5.2
23

1

4

100 1/4W

R1087

R1050

REEL_T

0.1 F

C1065

0.1 F

C1028

C1029

R1020 22K

R1017 39K

R1053 220

0.90.9 00

REEL-S

CAP FULL

DRUM-PWM

BOT

EOT

MSSEN-B

4

5

00 0 00

MS_SEN-B

EOT

BOT

MS_SEN-A

1.4

33K

OSD_R

OSD_G

OSD_B

V.REC_ST_H

22

R1021

C1009 220P CH

G

R

ENV-CMP-IN

VIDEO-H.SW

H.SW

TP1002

W825

COMP

X_RAY

DTC124EKA

0.1 F

C1017

10

R1035

10

C1023 220P CH

C1010 220P CH

4.8

B

NC

HI-FI-H.SW

LDM CTL

00 00

NC

9

NC

LDM_CTL

0.03

X_RAY
Q1014

NC

0

NC

OUT

SYSTEM RESET IC

123

IC1003 XC61CN3102SR

5.2 5.1

R1007

4.7K

R1063

NC NC

00

0

NC

NC

V REC START H

HEAD.AMP.SW

REMOCON-IN

COLOR ROTARY

NC NC

C1082

0.01 F

1006.3V YK

C1071

100P CH

OSD_BLK

C1004 100P CH

R1036 4.7K

C1037 390P CH

OSD OUT1

50 TAB SW

49 OSD-VSS

48 (AV2)

33 PLAY LED

32 RENT_H

31 ON-TIMER LED

X-RAY

4.5 0 5.2

R1055 4.7K

4.5

0

V-SYNC

H/C-SYNC

NC

DEGAUSS_H

4.7K

R1066

R1022 4.7K

NC

0

45

NC

GNDIN

0

C1034

220P CH

C1031

0.001 B

NUA

H_CONTROL

5.0

H_CTL

RESET

0.1 F

C1035

CVIN

PROTECT

5.2

PROTECT

R1049

4.7K

D1002

1SS133

C1056

0.1 F

VHOLD

EXT-MUTE

NC

R1054

1K

R1031

HLF

XC_OUT(32KHz)

XC_IN(32KHz)

VCR-POWER

C1083

0.0022 B

1K

R1051

18K 1/4W

3325V YK

C1021

SERVICE

TP1001

NC

5.22.11.62.300002.62.52.51.8

OSD-VCC

SD-IN(MONI)

NUB

OSC-OUT2

OSC-IN2

CLKSEL

X-RAY_TEST

VSS

X-OUT(12MHz)

X-IN(12MHz)

VCC

RESET-L

REC LED

T-REC LED

C1068

REC_LED

T-REC_LED

10006.3V YK

C1003_1

515253545556575859660616263646566676869770717273747576777879880

SERVICE

NC

TV-POWER

0.0022 B

R1032 10K

50

5.2

2.6

2.5

5.2

40 41 42 43 44 45 46 47 48 49

2.6

2.1

5.2

1.3

1.5

5.2

4.8

31 32 33 34 35 36 37 38 39

SD_SYNC

7

0

NC

0

NC(AV1)

0

0

NC

0

0

0

NC

NC

0

NC

0

6

C1038

330P CH

L1001

2.2uH

R1040

33K

8

X1001

100CT01207

12MHz

X1002

100DA32R01

32.768KHz

2.5 2.6 0 5.2
5678

SDA

SCL

VSS

A2

0

R1033

1K

C1046 20P CH

R1005

C1047 18P CH

2.7K

X-RAY_TEST

C1040 18P CH

C1048 18P

C1049 22P CH

C1050 20P CH

VCC

TEST

EEP ROM IC

A1

A0

1234

000

CH

RESET

IC1099

S-24C04BDP-LA

R1034

C1026

0.01 F

8

FROM/TO Y/C/AUDIO/HEAD AMP

Y/C_CLK

Y/C_DATA

Y/C_CS

C1062

1B

R1078

390K

1M

H.SW

SD_VIDEO

ENV_DET

VCR_A_MUTE

CTL+

CTL-

DUMMY_V.SYNC

V.REC_ST_H

H.AMP_SW1

COMP

SD_SYNC

7

6

FROM/TO CHROMA/IF

H_CTL

HD

VD

AFT_M

TV_POWER_H

SCL

SDA

OSD_R

OSD_G

OSD_B

OSD_BLK

AT+5V_BACKUP

AT+5V

VCR_POWER_H

FROM/TO IN/OUT

IIC_OFF

REC_LED
T-REC_LED
SCL
SDA

AT+5V

5

4

3

FROM AV

AT+5V

KEY_B

KEY_A

REMOCON_IN

GND

TO SOUND AMP

TV_POWER_H

TV_A_MUTE

FROM/TO DEFLECTION

X_RAY

X-RAY_TEST

PCB010
VMB281

2

1

NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME

OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE

NOTE:THE DC VOLTAGE EACH PART WAS

MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK.

CAUTION: DIGITAL TRANSISTOR

R.SIGNAL

G.SIGNAL

B.SIGNAL

AUDIO SIGNAL(REC)

PLAYBACK VIDEO SIGNAL

CAPSTAN AFC SIGNAL

TUNER VIDEO SIGNALDEFLECTION SIGNAL

CYLINDER APC SIGNAL

1

ABC D E F GH

ABC D E F GH

G-5

G-6

IN/OUT SCHEMATIC DIAGRAM

8

(SYSCON PCB)

8

7

6

5

4

CP351_1

TEST POINT

00_8283_0611_00

FROM/TO MICON

IIC_OFF

REC_LED

6

B.OUT

INT-MONI

SDA

SCL

IIC OFF

SDA

7

123

AT+5V

Y/C_AUDIO

GND

4

Y/C_VIDEO

12345

SCL

GND

CP1003

TEST POINT

173979-4

6

5

FROM CHROMA/IF

AT+5V

INT-MONI

0

3.6

REC LED SW(AI)

DTC114EKA

0

Q1007

T-REC/PLAY LED SW

Q4202

DTC114EKA

4.8

B.OUT

3.5

0

4

3

FROM Y/C/AUDIO/HEAD AMP

2

1

FROM AV

AT+5V

T-REC_LED

Y/C_AUDIO

Y/C_VIDEO

NOTE:THE DC VOLTAGE EACH PART WAS

MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK.

NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME

OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE

T-REC

D1004

270

R1086

SLR-342VCT32

CAUTION: DIGITAL TRANSISTOR

REC

D1013

R1084

270

SLR-342VCT32

B.SIGNAL

RECORD LUMINANCE SIGNAL

TUNER VIDEO SIGNAL RECORD COLOR SIGNAL

AUDIO SIGNAL(REC)

AUDIO SIGNAL(PB)

PLAYBACK LUMINANCE SIGNAL
PLAYBACK COLOR SIGNAL

GND

FROM/TO TV POWER

GND

PCB010

VMB281

3

2

1

ABC D E F GH

ABC D E F GH

G-7

G-8

AV SCHEMATIC DIAGRAM

8

TO Y/C/AUDIO/HEAD AMP

FRONT_AUDIO

FRONT_VIDEO

7

6

FROM/TO SOND AMP

GND

TO IN/OUT

SOUND_GND

AT+5V

GND

SOUND+

SP_OUT

SOUND_GND

GND

FRONT_AUDIO

FRONT_VIDEO

SOUND_GND

AT+5V

SOUND+

SP_OUT

SOUND_GND

5

TO MICON

REMOCON_IN

KEY_A

KEY_B

AT+5V

GND

REMOCON_IN

KEY_A

KEY_B

AT+5V

4

(SYSCON PCB)

FRONT_AUDIO

FRONT_VIDEO

SOUND_GND

SOUND+

C4205

C4211

R381

68 1/2W

SP_OUT

470P CH

0.1 F

R380

68 1/2W

C380

4.750V

R4203_1

KA

C381

75

4.750V

FRONT AUDIO(L)

FRONT VIDEO

C382

10016V YK

KA

PIC-37243SR

4.8

4.8

J4202

AV1-09D-4

2

H

J4201

AV1-09D-3

2

H

OS2201

0

3

2

1

1

E

1

E

1

NC

5

NC

4

3

2

6

7

GND

B+

Vout

TO CHASSIS

CD853

CH012101

HEADPHONE JACK

J351

MSJ-2000

8

7

6

5

4

KEY_B

KEY_A

SW2201

SW2207

R2201

EVQ21505R

R2206

820

EVQ21505R

820

REC/OTR

CH UP

3

POWER ON/OFF

CH DOWN

SW2202

SW2208

R2202

EVQ21505R

R2207

EVQ21505R

1K

SW2203

STOP/EJECT

1K

VOL UP

SW2209

2

1

CAUTION

:SINCE THESE PARTS MARKED BY

CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY

ARE

ATTENTION

:LES PIECES REPAREES PAR UN ETANT

DANGEREUSES AN POINT DE VUE SECURITE
N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES

NOTE:THE DC VOLTAGE EACH PART WAS

MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK.

AT+5V

REMOCON_IN

EVQ21505R

EVQ21505R

R1056

100 1/4W

R2203

1.5K

R2208

1.5K

NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME

R2204

2.7K

PLAY

SW2204

EVQ21505R

SW2210

VOL DOWN

EVQ21505R

OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE

C1053

6.3V

YK

220

SW2205

FF/CUE

D2201

EVQ21505R

MTZJ6.8B

R2205

5.6K

SW2206

REW/REV

EVQ21505R

TUNER VIDEO SIGNAL

AUDIO SIGNAL(REC)

PCB010
VMB281

3

2

1

ABC D E F GH

ABC D E F GH

G-9

G-10

8

7

6

5

TU601 TECC1040PG38W

4

3

FROM/TO TV POWER

FROM MICON

2

CHROMA/IF SCHEMATIC DIAGRAM

R616_1

150V KA

0.01 F

1K 1/4W

R620

100

C628_1

C627

0.4750V KA

W915

TPSRA4M50C00-A0

100P B

R665_1

10M 1/4W

C691

0.01 B

KTD863_Y

L607

R622

C669

W849

C625

150V KA

100P B

C622

REG.

Q604

8.35.0

CF604

12uH

330

R615

470

68P SL

C634

0.01 F

CHROMA/IF IC

IC601

M61250FP

C662_1

W843

AFT_M

Q606

C652

100 1/4W

5.0

B602

1K

REG.

C667

W842

S822X

4716V YK

C641

C640 0.1 F

NC

NC

NC

47 8.7V REG OUT
48 LIMITER IN
49 P.Con5.7V REG

64 VIF IN (2)

VIF Vcc

VIF Vcc

3

L609_1

100uH 0305

C646 0.1 F

W5RH3.5X5X1.0

1.2
H_CONT

Q607

2SC2412K

0.4

KTC3203_Y

0.01 F

D602

D601

100010V YK

C636

Hi Vcc

fsc OUT 2

1 V RAMP CAP
2 AFT OUT

V OUT

V RAMP FEEDBACK

5

6

R641

V_FEEDBACK

V_OUT

R607

390 1/2W

4716V

C624_1

MTZJ8.2B

1SS133

150V KA

C659

TV/Y IN

VREG Vcc

AFC FILTER

DEF GND

789

18K

C645

1B

C647

6.8K

R631

R623

220 1/4W

W827

KA

0.01 F

11.0 8.2

8.8

REG.

Q605

KTD863_Y

5.0

8.3

5.6

100

R628

2250V YK

C644

W865

R644_1

2.3
49

2.4

NC

50515253545556575859

QIF OUT

2.3
AUDIO OUT

3.0
AUDIO BYPASS

2.0
EXT AUDIO IN

3.2
FM DIRECT OUT

9.0
VIF VCO F/B

3.0
VIF GND

2.2
VIF GND

0

VIF VIDEO OUT

0

RF AGC OUT

2.4
VIF APC FILTER

6061626364

2.9

IF AGC FILTER2

2.3

IF AGC FILTER1

2.7
VIF IN (1)

1.5

2

1 101112

C664

163V MKT

0.1 B

4716V KA

C637_1

C620

4.5

1016V KA

R617

REG.

Q602

KTC3203_Y

C651

1006.3V KA

C660

0.1 F

VIDEO CHROMA Vcc

VIDEO CHROMA Vcc

34 X’TAL
33 ACL/ABCL
32 AT5.7V REG OUT

17 H VCO F/B
16 B OUT

FBP IN

DEF GND

1F

C666

C668_1

10K

R626

R656

1K

D603 1SS133

R657

H.PLUSE

H_OUT

4.8

47P CH

EXT C in

H OUT

4716V KA

2.2K

C653_1

FROM/TO MICON

PROTECT

AT+5V

AT+5V_BACKUP

VD

OSD_R

OSD_G

OSD_B

OSD_BLK

SDA

SCL

AFT_M

VCR_POWER_H

HD

L603

47uH 0305

C612

4706.3V YK

R605

100K

C613

0.1 B

L616

0.39uH

4.750V KA

1213

1.8

AGC

1

0

NC

2

2.5

NC

3

2.5

SCL

4

2.5

SDA

5

0

NC

6

4.9

+5V

7

0

NC

8

+30V

9

10

IF

11

1415

AT+30V

UNREG+8V CUT_OFF_SW

AT+12V

P.CON+5V_SW

AT+5V

H_GND

H_CTL

29.3

0

0

GND

NC

S824Y

C604

C602

0.1 F

C610

C605

100P CH

100P CH

W871

AT+5V

W895

TU_VIDEO

AUDIO_OUT

Y/C_AUDIO VCR_POWER_H

TU_AUDIO SCL

R601

10K

L601

0.56uH

CF602

MKT47.3MC110P-TF

C656

0.01 F

2.6

0

SFSRA4M50CF00-A0

R612 680 1/4W

C631

1F

C623 0.0047 B

R618 10M

C603_1

0.01 B

330

R609

C618 47P CH

C626

0.22 B

SAW FITER

CF601_1

TSF5229P3

GNDOUTOUTIN

1234

W861

1.9

BUFFER

Q601

2SA1037AK

CF603

C632

C621

(SYSCON PCB)

D608

8.0

SB140-EIC

5.5

150V KA

C649

0.015 B

R633

8.2K
C650

C654

X602

3.2

MCU RESET

VIDEO/CHROMA GND

VIDEO/CHROMA GND

CHROMA APC FILTER

STRAT UP Vcc

W874

fsc OUT 1

POWER ON CONT

CLOCK CONT

V PULSE OUT

INV FBP OUT

INTELLIGENT MONI

R OUT

NC

13 14 15 16

NC

D610 MTZJ6.8B

D609 MTZJ6.8B

R658 1.5K

1F

100

R634

R.OUT

G.OUT

18P CH

100DT3R531

2.0 8.83.2005.63.75.55.54.08.28.28.22.0NC2.0
333435363738394404142434445464748

Y SW OUT

SCL

SDA

FAST BLK

R IN

G IN

B IN

G OUT

R659 1.5K

R635

100

4.8 8.3

W801

C643

3.579545MHz

3.3

3.0

0

30 31 32

4.7

0

0.1

7.3

4.9

4.9

4.9

4.8

2.0

0

20 21 22 23 24 25 26 27 28 29

8.0

8.0

3.7

17 18 19

3.04.0 4.8 2.84.03.33.02.6 0 00.43.22.55.01.5

R636 100

B.OUT

NC

NC

NC

D611

R660 1.5K

KTC3203_Y

5.5

2250V YK

C675 68P CH

C629

68P CH

MTZJ6.8B

REG.

Q603

100

R663

R602 100

R603 100

R667

4.7K

C639

0.01 F

W852

R670

1M

C648

0.2250V KA

S822Y

4.8

ACL_CANCEL

Q611

DTA114EKA

R627_1

R613_1

2.2K 1/4W

R638

15K

0.2

4.9

R649 5.6K

2.2K 1/4W

R650

470 1/4W

R668

330 1/4W

R646

33K

R642

10K

R655_1

330 1/4W

ACL_CANCEL

Q609

DTC114EKA

R647

5.6K

R643_1

47K 1/4W

R639_1

2.2K 1/4W

R669

470

C665

1016V KA

0.2

4.8

0

R648

5.6K

C688_1 0.056 F

W850

R625

10K

S819X

11ES1-EIC

C630

100P CH

W828

D605

R652

4.7K

PROTECT

AT+5V

OSD_BLK

INT-MONI

SDA

VD

HD

OSD_R

OSD_G

OSD_B

W878

CUT_OFF

B.OUT

G.OUT

R.OUT

HEATER

180V

FROM/TO Y/C/AUDIO/HEAD AMP

SD_VIDEO

TU_VIDEO

TU_AUDIO

Y/C_AUDIO

VD

TO IN/OUT

INT-MONI

B.OUT

AT+5V

TO SOUND AMP

AUDIO_OUT

FROM/TO DEFLECTION

ACL

GND

V_OUT

HEATER

V_FEEDBACK

180V

H_OUT

H.PLUSE

H_GND

TO CRT

(CP851B)

CP851A

B2013H02-10P

H_GND1

10

9

8

7

6

5

4

3

NC

2

1

8

7

6

5

4

3

2

R.SIGNAL
G.SIGNAL

B.SIGNAL

AUDIO SIGNAL(PB)
AUDIO SIGNAL(REC)

1

DEFLECTION SIGNAL
PLAYBACK VIDEO SIGNAL
TUNER VIDEO SIGNAL

H_GND

PCB010

VMB281

CAUTION: DIGITAL TRANSISTOR

CAUTION: DIGITAL TRANSISTOR

NOTE:THE DC VOLTAGE EACH PART WAS

MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK.

NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME

OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE

CAUTION

:SINCE THESE PARTS MARKED BY

CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY

ARE

ATTENTION

:LES PIECES REPAREES PAR UN ETANT

DANGEREUSES AN POINT DE VUE SECURITE
N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES

1

ABC D E F GH

ABC D E F GH

G-11

G-12

SOUND AMP SCHEMATIC DIAGRAM

8

(SYSCON PCB)

8

7

CP354 CH121701

SP_OUT

SOUND_GND

FROM/TO IN/OUT

SP_OUT

SOUND+

6

SOUND_GND

FROM/TO A/V

SOUND+

SP_OUT

SOUND_GND

GND

W809

14

CP352 CU123201

SP_OUT

SOUND_GND

1

2

1

2

SPEAKER

SPEAKER

SP353

SG08G35BRA

8 OHM

SP351

SG08G35BRA

8 OHM

5

W814

5678

08.2 3.5 3.4

7

6

5

-+

SOUND AMP IC

4

FROM MICON

TV_A_MUTE

TV_POWER_H

FROM TV POWER

SOUND+B

3

GND

SOUND_GND

R359

47K

R353

68K

C354_1

0

C301

0.012
B

2.250V KA

C351

220010V YK

1234

C356_1

IC351 AN7511

3.95.1 0.3

1050V KA

4

3

R352

FROM CHROMA/IF

AUDIO_OUT

C355_1

0.4750V KA

R357

1K

2

NOTE:THE DC VOLTAGE EACH PART WAS

1

MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK.

NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME

OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE

CAUTION

:SINCE THESE PARTS MARKED BY

CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY

ARE

4.7K

S819Y

ATTENTION

:LES PIECES REPAREES PAR UN ETANT

DANGEREUSES AN POINT DE VUE SECURITE
N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES

AUDIO SIGNAL(REC)

PCB010
VMB281

2

1

ABCDEFGH

8

G-13

G-14

CAUTION

ATTENTION

ABC D E F GH

POWER SCHEMATIC DIAGRAM

5A 125V

:FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,

REPLACE ONLY WITH THE SAME TYPE FUSE

5A 125V (F501).

:POUR UNE PROTECTION CONTINUE LES RISQUES D’INCEIE

N’UTILISER QUE DES FUSIBLE DE MEME TYPE

5A 125V (F501).

(SYSCON PCB)

8

1

2

CD503

JM-2BK-61

1

2

(MOTOR GND)

+B(A)

+B(B)

TO SOUND AMP

SOUND+B

GND

SOUND_GND

TO Y/C/AUDIO/HEAD AMP

GND

P.CON+5V

TO DEFLECTION

GND

+B

AT+12V

H_GND_1

H_GND

FROM/TO IN/OUT

GND

TO MICON

GND
P.CON+5V

POWER_FAIL2

GND

MOTOR+12V

FROM/TO CHROMA/IF

H_GND
AT+30V

AT+12V

UNREG+8V

AT+5V

P.CON+5V_SW
GND

7

6

5

4

3

2

CP503

RE-H022TD-1130

7

C516

470P500V B

D505

21DQ09N

6

5

4

3

2

DEGAUSS COIL

8R200026

AC120V_60Hz

CD501

0R414903

BLADE

WIDE

L503

WHITE

BLACK

21

CP502

A1561WV2-2P

1

2

003P-2100

ZPB45BL3R0A

S101A

S102A

+B ADJ

R529

CP505

TH501_1

2.7K 1/4W +-1%

003P-2100

FH502

EYF-52BCY

330

VR502

POWER_FAIL2

EMEGENCY

CP504

5A 125V

F501

51MS050L

51MS050LCC

EYF-52BCY

R530

D501

MTZJ10B

POWER_FAIL

10K

R516

2SA1037AK

POWER_FAIL

FH501

1K

R513

10K

9.8

Q505

R500

0

2.7M 1/2W

8.6

0

2.1

R507

+-10%

C506_1

PROTECT SW

DTC114EKA

0

47K

COIL,LINE FILTER

0.22275V ECQUL

Q508

AT+5V

W838

L502

SS24V-10100

34

12

R552_1

R553

R554

10K

FEED BACK
SWITCHING

Q507

KTC3198

39K 1/2W

22K 1/4W

R509

3.3 5W

C549

0.01 B

C554

0.0022 B

6.0

R501

1.5M 1/2W

D528

15.7

5.4

R532

4.7K 1/4W

330 1/4W

MTZJ5.6B

R505

D518

RM11C-EIC

D520

RM11C-EIC

FEED BACK

TLP621(GR)

R533

C507

C508

C509

470200V UP

IC502

820 1/4W

RM11C-EIC

0.001500V B

500V

RM11C-EIC

D521

B

0.001

D530

HS501

763WSAA013

54.4

1

2

53.6

R528

0.22 1W

R502

10.1

34

1.7

D534

R5041MR5061MR510

180

D

10 3W

G

15.6

S

0.0012KV R

SWITCHING

0

C535_1

STP5NC50FP

R514

0.33 1W

MTZJ18B

C537_1

4725V MHE

R527

R534

100 1/4W

10K

C530

1M

Q510

R525

C536

0.0022250V KX

S826X

R511

1M 1/4W

B501

W4BRH3.5X6X1.0X2

C510

0.0047 B

R524

1.8K

0.4

0.022 B

0.0022250V KX

C539

560 1/4W

0.5

D535 MTZJ18B

R517

330 1W

D533

1SS133

R531221/4W

D537

1SS133

SWITCHING

Q511

3.4
KTC3203_Y

D536

1N4937

C515_1

C532

270P B

0.01100V MMTS

T501 81290804

195

DC IN

8

6

NC

160

5

COL

4

NC

3

0

2

GND

32

1

ADJ

12V

135V

12V

D508

1SS133

RU2AM-EIC

C517_1

R536

100 1/4W

220016V YK

C524_1

D510_1

470P2KV R

C522

150V YK

C534

B503

W5RH3.5X5X1.0

0.00182KV R

C541_1

C518

470P500V B

D512

21DQ09N

D514

1SS133

21DQ09N

D517

1N4937

C519

21DQ09N

D504

1SS133

C505

470P500V B

D507

470P500V B

D519

D513

1SS133

NC

10

32

SB

11

SG

12

13

5V

14

0

LG

15

16

0

17

HG

18

B505

W5RH3.5X5X1.0

D503

MTZJ8.2B

R535

D502

100

1SS133

C531_1

R519_1

47K

W833

220200V YXF

C521

C511

47025V YK

R503

1 1/2W

1234

8.2

100016V YK

763WSA0019

NC

134.6

135.0

0

PROTECT DRIVE

2250V MHE

2SA1624

R521

5.6K 1/4W

R520

12W

R512

56K 1/2W

R508

56K 1/2W

1F

C527

330016V

YK

C523_3

10

R640

R651 10 1/2W

IC501 KIA78R05API

HS504

1/2W

5V REG

OUTIN GND SW

0

C542

47010V YK

EMEGENCY

Q503

W830

AT+30V

D515

AT+12V

POWER_FAIL

UNREG+8V

4.84.9
W834

R522

100 1/4W

+B

MTZJ33B

PCB010

VMB281

CAUTION: DIGITAL TRANSISTOR

1

THE RESISTOR MARKED F IS FUSE RESISTOR.NOTE:
THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP
IS NON POLAR ONE.

NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED

WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.

NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME

OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE

CAUTION

:SINCE THESE PARTS MARKED BY

CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY

ARE

ATTENTION

:LES PIECES REPAREES PAR UN ETANT

DANGEREUSES AN POINT DE VUE SECURITE
N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES

1

ABC D E F GH

8

G-15

G-16

7

6

5

4

3

2

FROM/TO CHROMA/IF

V_OUT

V_FEEDBACK

H.PLUSE

HEATER

H_GND

H_OUT

FROM TV POWER

H_GND

H_GND_1

AT+12V

FROM/TO MICON

X_RAY

X-RAY_TEST

ABC D E F GH

DEFLECTION SCHEMATIC DIAGRAM

180V

GND

GND

ACL

+B

W928

W829

W917

W853

W813

W841

S830X

W831

SWITCHING

DTC114TKA

IC401 AN5522V.OUTPUT IC

­AMP

+

PUMP UP

Vcc GND

1234567

3.6 25.9 2.0 0 12.5 26.3 3.7

11E1-EIC

R401

470

20

S803Y

MTZJ5.1B

D409

HZ11B3L

SWITCHING

Q404

DTA144EKA

10035V MHE

C406

10.8

0

0

Q403

C403

4.9

D401

17

D408

150V YK

0

0

THERMAL PROTECTION

D403

MTZJ30B

D404

MTZJ30B

R402

270 1W

C416

22P CH

31.0

0.5

H-DRIVE

Q405
2SC1627_Y

R446

18K +-1%

+-1%

R445

5.6K
R442_1

R444

4.7K +-1%

15K +-1%

R409_1

8.2K 1/4W

(SYSCON PCB)

D402

1N4937

11E1-EIC

TO DY

CP401

A1561WV2-A5P

NC

5

4

3

2

1

A51LZM10X20N45

9

10

8
6

11

FOCUS

SCREEN

V801

R
G
B

175

2

1

CD801

CU823001

CAUTION: DIGITAL TRANSISTOR

CAUTION: DIGITAL TRANSISTOR

DEFLECTION SIGNAL

PCB010

VMB281

TO CRT

W807

MTZJ6.8B

C402

100035V YK

R450_1

2.2 2W

W857

W840

C420

100P500V B

R423

10K 1/4W

C431

D413

1N4937

10250V YK

262.0

136.0

135.0

W811

22.3

NC

S826Y

0

8.1

0

1.5

NC

FB401 FQI-20B001R

COL

1

E180

6

B+

2

AFC

9

HEA
TER

10

GND

8

E12

4

E27

3

GND

8

E8

5

C432_1

R453

150K 1/4W

0.1100V MHE

R490

68K 1/4W

GND

ABL

W817

HV

F

S

11

7

D405

0

0.7

R421

220 1/2W

V.POSI

560 1/2W

HS402

763WSAA013

VR401

METAL

2.2K

R408_1

1.3

680 1/2W

C422

R447

W936

W925

1250V MHE

68 1/2W

H.OUTPUT

0

TT2140LS-CBC

R419

R417

C438

R410

220 2W

19

0.001500V B

R460

C407

560 1/2W

100025V YK

W816

100 1/4W

R413

820

R411

27K +-1%

31.0

0.2

22.3

C418

C419_1

NC

D411

11E1-EIC

ETH09K14BZ

34

2

1

2250V YK

22100V YK

D407

11E1-EIC

0.01100V MMTS

C417_1

0

R456

470 1/2W

W854

R416

82K

10K

R414

150V KA

C405

R415

1.5 1/2W

T401

0 262.0

6

1.3

D412

1N4937

Q406

L401_1

4.7mH

18

C424_1

C423

MPP

0.0072

HS401_1

763WAA0162

0.47250V PMS

1.5KV

R449

C451

1 1/2W

0.22100V MKT

D410

8

7

6

5

4

3

2

1

NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED

WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.

ABC D E F GH

NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME

OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE

CAUTION

:SINCE THESE PARTS MARKED BY

CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY

ARE

ATTENTION

:LES PIECES REPAREES PAR UN ETANT

DANGEREUSES AN POINT DE VUE SECURITE
N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES

THE RESISTOR MARKED F IS FUSE RESISTOR.NOTE:
THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP
IS NON POLAR ONE.

1

ABC D E F GH

G-17

G-18

CRT SCHEMATIC DIAGRAM

8

TP801

132.5

2.5

GREEN AMP

Q805

2SC4217

2.9

21

22

132.1

2.5

BLUE AMP

7

4.7K

R814

R811

330

C809

560P B

CP851B
B2013H02-10P

10

9

8

7

6

5

4

3

2

1

CUT_OFF_SW

FROM/TO CHROMA/IF

(CP851A)

GND

CUT_OFF

B.OUT

G.OUT

R.OUT

H_GND

HEATER

NC NC

180V

CUT_OFF

B.OUT

G.OUT

R.OUT

NC

H_GND1

HEATER

180V

GND

6

5

Q804

2SC4217

2.8

TP802

(CRT PCB)

R802

12K 1W

R807

2.7K 1/4W

R805

12K 1W

R808_1

2.7K 1/4W

132.5

132.9

0

104.1

6

5

0

0

789

1

F

0

10

11

ISHS53S

132.8

J801

8

7

6

5

R820_1

4.7K

R815

R812

330

C810

470P B

4

RED AMP

Q806

2SC4217

2.8

23

132.3

2.5

3

R816_1

R813

330

C811

470P B

2

PCB110
TCB413

4.7K 1/4W

C805

330P B

TP803

2.7K 1/4W

R810

12K 1W

FROM/TO DEFLECTION

CC002

TP-1S-05

L801

100uH

(CD801)

A2361WV2-2P

CP801

GND

2

GND

1

S804

S802

FOCUS

C801_1

SCREEN

S801

0.0012KV R

BL001

HPN-01

BT101

R03(AB)E_2P_G

ACCESSORY

TM101

RC-JG

BT102

R03(AB)E_2P_G

4

3

2

1

NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED

WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.

NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME

OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE

CAUTION

:SINCE THESE PARTS MARKED BY

CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY

ARE

ATTENTION

:LES PIECES REPAREES PAR UN ETANT

DANGEREUSES AN POINT DE VUE SECURITE
N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES

R.SIGNAL

G.SIGNAL

B.SIGNAL

1

ABC D E F GH

ABC D E F GH

G-19

G-20

INTERCONNECTION DIAGRAM

8

ROTOR

MAGNETCOIL

MR

FG SENSOR

G

O

VCC

CAPSTAN DD UNIT ASS’Y

M2001

HALL

IN

MAIN

OUT

SWITCH

LOGIC

HALL

SENSOR

1

CAP_FG

CAP_VCO

VCC

CAP/M/F/R

I_LIMIT

GND[M]

GND

LD/CY_VCO

CAP_CTL

LDM_CTL

CYL_FG/PG

CYL_CTL

2

HALL
VCC

1

2

3

4

5

6

7

8

9

10

11

12

1

2

3

4

5

6

7

TM101

COMMAND TRANSMITTER

TO

HEADPHONE JACK

L503

8 OHM

SP351

BLADE

WIDE

J351

SPEAKER

WHITE

BLACK

21

1

5

4

3

2

6

7

S101A

S102A

CP502

2

DEGAUSS COIL

1

DEGAUSS COIL

CP352

SOUND_GND

2

1

SP_OUT

7

6

AC120V_60Hz

CD501

DEGAUSS COIL

5

E

1

2

H

FRONT AUDIO(L)

J4202

E

1

2

H

FRONT VIDEO

J4201

OS2201

FROM

OS2201

REMOCON SENSOR

GND

B+

TM101

V.OUT

LM

LOADING MOTOR

M101

CP1001

1

2

3

4

5

6

7

8

9

10

11

12

8

7

6

5

SPEAKER

SP353

8 OHM

+B(A)

+B(B)

4

3

8

79

6

CRT SOCKET

5

J801

1

9

B.OUT

CUT_OFF

G.OUT

F

R.OUT

1

2

CP801

2

GND

GND

CD801

CP851B

GND

CD503

1

2

10

11

H_GND

2

1

HEATER

CP354

CP503

1

2

SOUND_GND

SP_OUT

FOCUS SCREEN

S801

SCREEN

1102345678

CRT PCB

180V

PCB110
TCB413

FOCUS

V801

H5001

MICRO MOTOR

M2003

CH2

CH1

SP
HEAD

AUDIO

CONTROL

FE

4

3

2

FBT

FB401

CP401

5

4

3

2

NC

1

CP851A

GND

10

9

ANODE

H.V

CRT

CUT_OFF

B.OUT

G.OUT

R.OUT

CUT_OFF_SW

H_GND

HEATER

NC

180V

SYSCON PCB

PCB010
VMB281

8

7

6

5

4

3

2

1

1

1

GND

GND

TUNER PACK

TU601

IF

11

NC

10

+30V

9

NC

8

+5V

7

NC

6

5

SDA

SCL

4

3

NC

NC

2

AGC

1

U IN

CP4001_1

1

2

SP-CH2 (L)

3

SP_COM

4

SP-CH1 (R)

CP4002

6

AUDIO REC AUDIO REC

5

AUDIO PB

4

CTL+

3

CTL-

2

FE HEAD(-)

FE HEAD(+)

1

CP4003

FE HEAD (GND)

2

FE HEAD (HOT)

1

CD4001

FFC

1

2

3

4

2

1 FE HEAD (HOT)

CD2001

U-OUT

V-OUT

W-OUT

M-COM

GND

PG_OUT

PG-GND

CYLINDER UNIT ASS’Y

UN4001

NC

6

5

AUDIO PB

4

CTL+

3

CTL-

2

FE HEAD(-)

FE HEAD(+)

1

FE HEAD (GND)

FULL ERASE HEAD ASS’Y

1

2

3

4

5

6

7

HEAD AUDIO CONTROL ASS’Y

H5002

CD853CD852

1

OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE

THE TIMETHIS INTERCONNECTION DIAGRAM IS THE LATEST ATNOTE:

FROM/TO DECK

CAUTION

:SINCE THESE PARTS MARKED BY

CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY

ARE

ATTENTION

:LES PIECES REPAREES PAR UN ETANT

DANGEREUSES AN POINT DE VUE SECURITE
N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES

1

ABC D E F GH

WAVEFORMS

Y/C/AUDIO/HEAD AMP

1PB

0.5V 20µs/div

2 POWER ON
100mV 0.1µs/div

MICON

6 POWER ON

1.0V 20µs/div

7 POWER ON

0.5V 10ms/div

11 PB

0.5V 0.5ms/div

13 PB

1.0V 5ms/div

SOUND AMP

3 PB
10mV 20µs/div

4 PB

0.5V 1ms/div

5 REC

10.0V 5µs/div

8 POWER ON

1.0V 10µs/div

14 POWER ON
200mV 2ms/div

DEFLECTION

9 PB

1.0V 10ms/div

10 PB

1.0V 5ms/div

The following waveforms were measured at the point of the corresponding

NOTE:

balloon number in the schematic diagram.

H-1

17 POWER ON

0.5V 5ms/div

18 POWER ON

10.0V 5ms/div

19 POWER ON

2.0V 20µs/div

20 POWER ON
200mV 20µs/div

CRT

WAVEFORMS

21 POWER ON

50.0V 20µs/div

22 POWER ON

50.0V 20µs/div

23 POWER ON

50.0V 20µs/div

The following waveforms were measured at the point of the corresponding

NOTE:

balloon number in the schematic diagram.

H-2

MECHANICAL EXPLODED VIEW

202

110

125

112

203

203

125

203

202

202

102B

113

PCB110
(CRT PCB ASS'Y)

102A

102C

102B

102

109

202

202
202

202

205

125

101F

101E

101B

101K

125

101D

203

101C

101J

101I

205

101G

101H

205

A

101A

101

I1-1

MECHANICAL EXPLODED VIEW

207

211

204

108

204

211

105

103

201

104

208

111

107

106

104

206

209

210

107

212

208

A

PCB010
(SYSCON PCB ASS'Y)

201

I1-2

MECHANICAL EXPLODED VIEW

(PACKING DIAGRAM)

120, 121, 122, 123, 124,
BL001, TM101

116

116

115

118

114

117

I1-3

CHASSIS EXPLODED VIEW (TOP VIEW)

341

331

302

334

314

323

508

333

315

AA

M2003

501

H5002

322

336

508

511

324

AA

335

342

503

332

CD1501

UN4001

504

312

305

300

H5001

347

306

301

AA

313

AA

AA

AA

AA

318

AA

325

317

CLASS

GREASE

309

321

MARK

AA

AA

AA

319

AA

NOTE:

AA

AA

307

AA

AA

320

507

316

348

510

Applying positions AA for the grease are
displayed for this section.
Check if the correct grease is applied for
each position.

506

CD1502

M101

304

349

345

346

AA

AA

I2-1

CHASSIS EXPLODED VIEW (BOTTOM VIEW)

308

327

509

344

343

AA

338

502

AA

337

M2001

AA

AA

502

AA

CD1502

340

CD1501

AA

AA

AA

502

AA

329

303

AA

311

339

310

AA

300

AA

328

326

CLASS

GREASE

MARK

AA

AA

NOTE:

AA

505

330

Applying positions AA for the grease are
displayed for this section.
Check if the correct grease is applied for
each position.

I2-2

MECHANICAL REPLACEMENT PARTS LIST

Location No. TSB P/N Reference No. Description

101 AE002917 7A701A013A FRONT CABI ASS'Y
101A AE002918 701WPJC498 CABINET,FRONT
101B AE002919 711WPA0201 PLATE,FRONT
101C AE002920 712WPJB960 FLAP
101D AE002921 713WPA0313 GLASS,LED
101E AE002922 713WPA0314 GUIDE,REMOCON
101F AD302008 7235490036 BADGE,BRAND
101G AE002924 735WPBA949 BUTTON,PUSH
101H AE003258 735WPAA650 BUTTON,FRAME
101I AE002925 738WPA0089 STOPPER,BUTTON
101J AD301686 743WKA0037 SPRING,FLAP
101K AE003110 800WQ0A052 FELT SHEET

102 AE002926 7A702A008A BACK CABI ASS'Y
102A AE002927 702WPAA625 CABINET,BACK
102B AE002928 800WQ00066 FELT SHEET
102C AE003113 800WQ0A036 FELT SHEET

103 BZ710466 752WSA0230 SHIELD,CASE HEAD AMP
104 AE000049 753WSA0118 PLATE,EARTH-SYSCON
105 BZ710331 753WUAA006 SPRING,EARTH HEAD AMP
106 BZ710557 761WPA0225 HOLDER,DECK
107 BZ710498 85OP700038 HOLDER,END SENSOR
108 AD301750 752WSAA051 PLATE,DECK SHIELD
109 AE002929 722549A301 SHEET,RATING

110 AE002930 723000C458 POP LABEL
111 BZ710260 899HV3T000 HOLDER,ANODE WIRE
112 AD300759 741WUA0021 SPRING,EARTH
113 AE002931 726000A057 SHEET,CRT SERVICEMAN
114 AE002932 723000C459 SHEET,BAR CODE
115 AE000010 791WHA0085 LAMIFILM,BAG
116 AE002933 792WHA0524 PACKAGE,TOP
117 AE002934 792WHA0525 PACKAGE,BOTTOM
118 AE002935 793WCDC054 GIFT BOX
119 AE002936 A5L9019975 INSTRUCTION BOOK KIT

120 AD300812 JB5UD400 POLYBAG,INSTRUCTION(RED CAUTION)
121 AE001184 J5F10129A INFORMATION SHEET
122 AE002937 J5L90101A INSTRUCTION BOOK
123 AD302404 J5500817 REGISTRATION CARD
124 AE001396 J5500836 ESP CARD
125 AE000412 769WSAA005 WASHER CRT T=1

201 BZ710036 8117540B04 SCREW,TAPPING(B0) TRUSS 4x20
202 BZ710035 8117540A64 SCREW,TAPPING(B0) TRUSS 4x16
203 AD302054 8141J50C54 SCREW,TAP TITE(P) GW22 5x35
204 BZ710032 8110630A24 SCREW,TAP TITE(P) BRAZIER 3x12
205 BZ710031 8110630A04 SCREW,TAP TITE(P) BRAZIER 3x10
206 BZ710028 8110330804 SCREW,TAP TITE(P) FLAT 3x8
207 AD301667 8110E30804 SCREW,TAP TITE(P) WH10 3x8
208 BZ710239 8109I30A04 SCREW,TAP TITE(B) WH7 3x10
209 BZ710562 8109I30804 SCREW,TAP TITE(B) WH7 3x8

210 BZ710018 8107630804 SCREW,TAP TITE(S) BRAZIER 3x8
211 BZ710147 8107630604 SCREW,TAP TITE(S) BRAZIER 3x6
212 BZ710019 8109630802 SCREW,TAP TITE(B) BRAZIER 3x8

J1-1

CHASSIS REPLACEMENT PARTS LIST

Location No. TSB P/N Reference No. Description

300 AD301726 A5E301I420A DECK ASSY A5E301I420A
301 AE002754 85OA400240 PINCH ROLLER BLOCK (VA)
302 BZ710514 85OP900746 BRACKET,TOP 3V
303 BZ710193 85OP200290 BELT,CAPSTAN (S)
304 BZ710515 85OP600581 WORM
305 BZ710094 85OP500083 BASE,AC HEAD
306 BZ710112 85OP800324 SPRING,AC HEAD
307 BZ710516 85OA000459 MAIN CHASSIS ASS'Y
308 BZ710517 85OA200089 CLUTCH ASS'Y
309 BZ710518 85OA200090 ARM IDLER ASS'Y

310 BZ710519 85OA300065 LOADING ARM S UNIT
311 BZ710520 85OA300066 LOADING ARM T UNIT
312 BZ710521 85OA400223 INCLINED BASE T UINT 3S
313 BZ710522 85OA400232 P5 ARM ASS'Y 2
314 BZ710650 85OA400235 TENSION ARM ASS'Y 2
315 BZ710524 85OA400231 INCLINED BASE S UNIT
316 AE000442 85OP800367 SPRING,LOCKER
317 BZ710526 85OP900736 CASS,HOLDER
318 BZ710527 85OP900748 CASS,SIDE L
319 BZ710528 85OP900749 CASS,SIDE R

320 BZ710529 85OP900739 LOCKER,R
321 BZ710530 85OA900228 LINK UNIT
322 BZ710531 85OP000496 POST,CASS GUIDE
323 BZ710532 85OP200316 REEL,S (S)
324 BZ710533 85OP200317 REEL,T (S)
325 BZ710534 85OP200308 GEAR,IDLER
326 BZ710535 85OP200311 GEAR,CLUTCH
327 BZ710536 85OP200312 GEAR,COUPLING
328 BZ710537 85OP200313 LEVER,CLUTCH
329 BZ710538 85OP300194 GEAR,MAIN LOADING

330 BZ710092 85OP400490 LEVER,TENSION
331 BZ710093 85OP400492 HOLDER,TENSION
332 BZ710366 85OP400520 CAP.P4
333 BZ710762 85OP400542 BAND,TENSION
334 BZ710540 85OP400533 CONNECT,TENSION
335 BZ710541 85OP600573 ARM,BRAKE T
336 BZ710763 85OP600584 BAND,BRAKE T
337 BZ710543 85OP600577 CAM,PINCH ROLLER
338 BZ710544 85OP600578 CAM,MAIN
339 BZ710545 85OP600579 ROD,MAIN

340 BZ710546 85OP600582 GEAR,JOINT
341 BZ710110 85OP800322 SPRING,TENSION
342 BZ710547 85OP800360 SPRING,BRAKE T
343 BZ710548 85OP800355 SPRING,COUPLING
344 BZ710549 85OP800356 SPRING,RING
345 BZ710565 85OP900750 LEVER,LINK 2
346 BZ710551 85OP900744 LEVER,FLAP
347 BZ710552 85OP900745 CASS,OPENER
348 BZ710106 85OP700035 REFLECTOR,LED
349 BZ710796 85OP700039 COVER,BOT

501 BZ710049 8107226804 SCREW,TAP TITE(S) BIND 2.6x8
502 BZ710058 83ETW30000 E-RING 3.0
503 BZ710371 8107226404 SCREW,TAP TITE(S) BIND 2.6x4
504 BZ710046 8102120604 SCREW,PAN M2x6
505 BZ710050 8109126604 SCREW,TAP TITE(B) PAN 2.6x6
506 BZ710553 810A130404 SCREW/WASHER(A) M3x4
507 BZ710219 810A126504 SCREW/WASHER(A) M2.6x5
508 BZ710056 82Q264713N POLYSLIDER WASHER 2.6x4.7xT0.13
509 BZ710054 82P184505N POLYSLIDER WASHER(CUT) 1.8x4.5xT0.5

510 BZ710017 8107226604 SCREW,TAP TITE(S) BIND 2.6x6
511 BZ710051 810A123504 SEMS A M2.3x5.0

CD1501 BZ614292 122H071704 CORD JUMPER 2H071704
CD1502 BZ614339 122Y021902 CORD JUMPER 2Y021902
H5001 AD301675 1523Q91003 HEAD (AUDIO CONTROL) VTR-1X2RPE22-756

H5002 AD301676 1543Q02014 HEAD (FULL ERASE) VTR-1X2ERS11-154
! M101 BZ710566 1596P98001 MOTOR (LOADING) MXN13FB12K3
! M2001 AE002696 1510S98040 CAPSTAN DD UNIT F2QVB33B
! M2003 BZ710373 1589S11014 MICRO MOTOR I2OAL03
! UN4001 BZ610290 A5A305A500 CYLINDER UNIT ASS'Y A5A305A500

J2-1

ELECTRICAL REPLACEMENT PARTS LIST

Location No. TSB P/N Reference No. Description

RESISTORS

! R402 BZ210225 R3X181271J R,METAL OXIDE 270 OHM 1W
! R410 AD301140 R3X28A221J R,METAL OXIDE 220 OHM 2W
! R415 BZ210130 R002T21R5J RC 1.5 OHM 1/2W
! R442 AD301014 R4X5T6472F R,METAL 4.7K OHM 1/6W
! R444 AE002906 R803R9153F RC 15K OHM 1/16W
! R445 AE002907 R803R9562F RC 5.6K OHM 1/16W
! R446 AE002908 R803R9183F RC 18K OHM 1/16W
! R447 BZ210021 R65582680J R,FUSE 68 OHM 1/2W
! R449 AD301699 R635U2010J R,FUSE 1 OHM 1/2W
! R450 AE000610 R6358A2R2J R,FUSE 2.2 OHM 2W
! R500 BZ210080 R0G3K2275K RC 2.7M OHM 1/2W
! R501 AD301632 R5Y2CD3R3J R,CEMENT 3.3 OHM 5W
! R502 BZ210215 R3X28B100J R,METAL OXIDE 10 OHM 3W
! R509 BZ210206 R002T2155J RC 1.5M OHM 1/2W
! R510 AE001887 R803R9105J RC 1M OHM 1/16W
! R512 BZ210158 R002T2563J RC 56K OHM 1/2W
! R514 BZ210048 R3X181R33J R,METAL OXIDE 0.33 OHM 1W
! R517 BZ210217 R3X181331J R,METAL OXIDE 330 OHM 1W
! R520 BZ210083 R3X28A010J R,METAL OXIDE 1 OHM 2W
! R528 BZ210190 R63581R22J R,FUSE 0.22 OHM 1W
! R529 BZ210084 R4X5T4272F R,METAL 2.7K OHM 1/4W
! R802 BZ210089 R3X181123J R,METAL OXIDE 12K OHM 1W
! R805 BZ210089 R3X181123J R,METAL OXIDE 12K OHM 1W
! R810 BZ210089 R3X181123J R,METAL OXIDE 12K OHM 1W

CAPACITORS

C354 BZ110076 E02LF1222M CE 2200 UF 10V
! C402 BZ110077 E02L04102M CE 1000 UF 35V
! C407 BZ110078 E02L03102M CE 1000 UF 25V
! C419 AD300064 E02LT8220M CE 22 UF 100V

C423 BZ210173 P4J7F3474J CMPP 0.47 UF 250V PMS
! C424 AE003259 P4N8FK722H CMPP 0.0072UF 1.5KV
! C431 BZ110103 E02LTD100M CE 10 UF 250V

C432 AD301868 E5EZ080R1M CE 0.1 UF 100V
! C506 BZ110025 P2122B224M CMP 0.22 UF 275V ECQUL
! C507 BZ110061 C0JTB0513K CC 0.001 UF 500V B

C509 BZ110012 E51CGC471M CE 470 UF 200V
! C511 BZ110041 E02LT3471M CE 470 UF 25V

C517 BZ110219 C0PLRR7Q2K CC 470 PF 2KV R
! C521 BZ110130 E62NFC221M CE 220 UF 200V

C523 BZ110104 E0EL02332M CE 3300 UF 16V

C524 BZ110135 E02L02222M CE 2200 UF 16V
! C530 AD301108 CD39E0MH3M CC 0.0022UF 250V

C535 BZ110202 C0PLRR713K CC 0.001 UF 2KV R
! C539 AD301108 CD39E0MH3M CC 0.0022UF 250V
! C541 AD301702 C0PLRR7G3K CC 0.0018 UF 2KV R

C669 AE002909 CHG0SL4U1J CC 68 PF 50V SL

C801 BZ110202 C0PLRR713K CC 0.001 UF 2KV R

C1003 BZ110154 E02L00102M CE 1000 UF 6.3V

DIODES

D401 BZ410043 D2WT011E10 DIODE,SILICON 11E1-EIC
! D402 AD300731 D2WXN49370 DIODE,SILICON 1N4937

D403 BZ410019 D97U03001B DIODE,ZENER MTZJ30B T-77

D404 BZ410019 D97U03001B DIODE,ZENER MTZJ30B T-77

D405 BZ410043 D2WT011E10 DIODE,SILICON 11E1-EIC

D407 BZ410043 D2WT011E10 DIODE,SILICON 11E1-EIC
! D408 BZ410020 D97U05R11B DIODE,ZENER MTZJ5.1B T-77
! D409 BZ410017 D94TA11B13 DIODE,ZENER HZ11B3L TD

D410 BZ410022 D97U06R81B DIODE,ZENER MTZJ6.8B T-77

D411 BZ410043 D2WT011E10 DIODE,SILICON 11E1-EIC
! D412 AD300731 D2WXN49370 DIODE,SILICON 1N4937
! D413 AD300731 D2WXN49370 DIODE,SILICON 1N4937
! D501 BZ410061 D97U01001B DIODE,ZENER MTZJ10B T-77

D502 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77

D503 BZ410058 D97U08R21B DIODE,ZENER MTZJ8.2B T-77

D504 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
! D505 BZ410010 D28T21DQN9 DIODE,SCHOTTKY 21DQ09N-TA2B1

D507 BZ410010 D28T21DQN9 DIODE,SCHOTTKY 21DQ09N-TA2B1

D508 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
! D510 BZ410080 D2WXRU2AM0 DIODE,SILICON RU2AM-EIC
! D512 BZ410010 D28T21DQN9 DIODE,SCHOTTKY 21DQ09N-TA2B1

D513 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77

J3-1

ELECTRICAL REPLACEMENT PARTS LIST

Location No. TSB P/N Reference No. Description

DIODES

D514 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
! D515 BZ410037 D97U03301B DIODE,ZENER MTZJ33B T-77
! D517 AD300731 D2WXN49370 DIODE,SILICON 1N4937
! D518 BZ410062 D2WTRM11C0 DIODE,SILICON RM11C-EIC
! D519 BZ410010 D28T21DQN9 DIODE,SCHOTTKY 21DQ09N-TA2B1
! D520 BZ410062 D2WTRM11C0 DIODE,SILICON RM11C-EIC
! D521 BZ410062 D2WTRM11C0 DIODE,SILICON RM11C-EIC

D528 BZ410021 D97U05R61B DIODE,ZENER MTZJ5.6B T-77
! D530 BZ410062 D2WTRM11C0 DIODE,SILICON RM11C-EIC

D533 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
! D534 AD300671 D97U01801B DIODE,ZENER MTZJ18B T-77
! D535 AD300671 D97U01801B DIODE,ZENER MTZJ18B T-77

D536 AD300731 D2WXN49370 DIODE,SILICON 1N4937

D537 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77

D601 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77

D602 BZ410058 D97U08R21B DIODE,ZENER MTZJ8.2B T-77

D603 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77

D605 BZ410059 D2WT11ES10 DIODE,SILICON 11ES1-EIC

D608 BZ410077 D2WXSB1400 DIODE,SCHOTTKY SB140-EIC

D609 BZ410022 D97U06R81B DIODE,ZENER MTZJ6.8B T-77

D610 BZ410022 D97U06R81B DIODE,ZENER MTZJ6.8B T-77

D611 BZ410022 D97U06R81B DIODE,ZENER MTZJ6.8B T-77

D1001 AD301638 0010E00330 INFRARED LED LTE-3271T-012A-O

D1002 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77

D1004 BZ410054 0021721150 LED SLR-342VCT32

D1013 BZ410054 0021721150 LED SLR-342VCT32

D1014 BZ410022 D97U06R81B DIODE,ZENER MTZJ6.8B T-77

D2201 BZ410022 D97U06R81B DIODE,ZENER MTZJ6.8B T-77

D4001 BZ410034 D97U01301B DIODE,ZENER MTZJ13B T-77

D4002 BZ410034 D97U01301B DIODE,ZENER MTZJ13B T-77

ICS

! IC351 BZ611001 I01DP75110 IC AN7511
! IC401 BZ611053 I01TD55220 IC AN5522

IC501 AE000560 I1KA9R05A0 IC KIA78R05API
! IC502 BZ410055 0002500450 PHOTO COUPLER TLP621(GR)

IC601 AD301639 I06FC61250 IC M61250FP

IC1001 AE002784 I56F57107A IC OEC7107A
! IC1003 AE002138 IE2F031020 IC XC61CN3102SR

IC1099 AE002910 A5L9019015 IC S-24C04BDP-LA

IC4001 AD301643 I03F3206M0 IC LA71206M-MPB

TRANSISTORS

Q403 BZ510022 TNYJJ05001 COMPOUND TRANSISTOR DTC114TKAT146

Q404 BZ510049 TPYJD05001 COMPOUND TRANSISTOR DTA144EKAT146
! Q405 BZ510089 TC5T01627Y TRANSISTOR,SILICON 2SC1627_Y(TPE2)
! Q406 BZ510120 TD3U021400 TRANSISTOR,SILICON TT2140LS-CBC

Q503 BZ510004 TA3T016240 TRANSISTOR,SILICON 2SA1624-AA

Q505 BZ510001 T6YJ1037K0 TRANSISTOR,SILICON 2SA1037AKT146R,S

Q507 BZ510069 TCATC31980 TRANSISTOR,SILICON KTC3198-AT(Y,GR)

Q508 BZ510020 TNYJB05001 COMPOUND TRANSISTOR DTC114EKAT146
! Q510 BZ510093 TJXG5NC500 FET STP5NC50FP
! Q511 BZ510070 TCAT032034 TRANSISTOR,SILICON KTC3203_Y-AT

Q601 BZ510001 T6YJ1037K0 TRANSISTOR,SILICON 2SA1037AKT146R,S

Q602 BZ510070 TCAT032034 TRANSISTOR,SILICON KTC3203_Y-AT

Q603 BZ510070 TCAT032034 TRANSISTOR,SILICON KTC3203_Y-AT

Q604 BZ510074 TDAT00863Y TRANSISTOR,SILICON KTD863_Y-AT

Q605 BZ510074 TDAT00863Y TRANSISTOR,SILICON KTD863_Y-AT

Q606 BZ510070 TCAT032034 TRANSISTOR,SILICON KTC3203_Y-AT

Q607 BZ510002 T8YJ2412K0 TRANSISTOR,SILICON 2SC2412KT146 R,S

Q609 BZ510020 TNYJB05001 COMPOUND TRANSISTOR DTC114EKAT146

Q611 BZ510025 TPYJB05001 COMPOUND TRANSISTOR DTA114EKAT146
! Q804 BZ510009 TC3F042170 TRANSISTOR,SILICON 2SC4217(D,E)-RAC
! Q805 BZ510009 TC3F042170 TRANSISTOR,SILICON 2SC4217(D,E)-RAC
! Q806 BZ510009 TC3F042170 TRANSISTOR,SILICON 2SC4217(D,E)-RAC

Q1003 BZ410106 0002700680 PHOTO COUPLER RPI-352C40N

Q1004 BZ510021 TNYJC05001 COMPOUND TRANSISTOR DTC124EKAT146
! Q1005 BZ410107 0002700690 PHOTO COUPLER RPI-303

Q1007 BZ510020 TNYJB05001 COMPOUND TRANSISTOR DTC114EKAT146

Q1009 BZ410106 0002700680 PHOTO COUPLER RPI-352C40N

Q1011 BZ410097 0000M00390 PHOTO TRANSISTOR ST-304L

Q1013 BZ410097 0000M00390 PHOTO TRANSISTOR ST-304L

Q1014 BZ510021 TNYJC05001 COMPOUND TRANSISTOR DTC124EKAT146

J3-2

ELECTRICAL REPLACEMENT PARTS LIST

Location No. TSB P/N Reference No. Description

TRANSISTORS

Q4001 BZ510069 TCATC31980 TRANSISTOR,SILICON KTC3198-AT(Y,GR)

Q4002 BZ510069 TCATC31980 TRANSISTOR,SILICON KTC3198-AT(Y,GR)

Q4003 BZ510026 TPYJC05001 COMPOUND TRANSISTOR DTA124EKAT146

Q4005 BZ510073 TAATA12660 TRANSISTOR,SILICON KTA1266-AT(Y,GR)

Q4006 BZ510070 TCAT032034 TRANSISTOR,SILICON KTC3203_Y-AT

Q4007 BZ510002 T8YJ2412K0 TRANSISTOR,SILICON 2SC2412KT146 R,S

Q4009 BZ510001 T6YJ1037K0 TRANSISTOR,SILICON 2SA1037AKT146R,S

Q4010 BZ510001 T6YJ1037K0 TRANSISTOR,SILICON 2SA1037AKT146R,S

Q4011 BZ510002 T8YJ2412K0 TRANSISTOR,SILICON 2SC2412KT146 R,S

Q4012 BZ510002 T8YJ2412K0 TRANSISTOR,SILICON 2SC2412KT146 R,S

Q4202 BZ510020 TNYJB05001 COMPOUND TRANSISTOR DTC114EKAT146

COILS &TRANSFORMERS

L401 AD301644 021L75472J COIL 4.7 MH
! L502 BZ310075 029X000087 COIL,LINE FILTER SS24V-10100
! L503 BZ310033 028R200026 COIL,DEGAUSS 8R200026

L601 AE002911 0216A6R56K COIL 0.56 UH

L603 BZ310040 02167F470J COIL 47 UH

L607 AD301705 0216A6120K COIL 12 UH

L609 BZ310041 02167F101J COIL 100 UH

L616 AE002912 0216A6R39K COIL 0.39 UH

L801 BZ310002 021673101K COIL 100 UH

L1001 AD301706 0216A62R2K COIL 2.2 UH

L4001 BZ310039 02167F220J COIL 22 UH

L4003 BZ310041 02167F101J COIL 100 UH

L4005 BZ310040 02167F470J COIL 47 UH

L4006 BZ310040 02167F470J COIL 47 UH

L4009 BZ310041 02167F101J COIL 100 UH

T401 BZ310157 045009003J TRANS,HORIZONTAL DRIVE ETH09K14BZ
! T501 BZ310160 0481290804 TRANSFORMER,SWITCHING 81290804

T4001 BZ310114 031626009R COIL,BIAS OSC 1626009

JACKS

J351 BZ614361 060J131015 HEADPHONE JACK MSJ-2000
! J801 AD301356 066F130020 SOCKET,CATHODE RAY,TUBE ISHS53S

J4201 AD300680 060Q401077 RCA JACK AV1-09D-3

J4202 AD300681 060Q401076 RCA JACK AV1-09D-4

SWITCHES

SW1001 BZ612016 0508S11001 SWITCH (LEAF) LSA-1144EAU

SW2201 BZ612010 0504101T34 SWITCH,TACT EVQ21505R

SW2202 BZ612010 0504101T34 SWITCH,TACT EVQ21505R

SW2203 BZ612010 0504101T34 SWITCH,TACT EVQ21505R

SW2204 BZ612010 0504101T34 SWITCH,TACT EVQ21505R

SW2205 BZ612010 0504101T34 SWITCH,TACT EVQ21505R

SW2206 BZ612010 0504101T34 SWITCH,TACT EVQ21505R

SW2207 BZ612010 0504101T34 SWITCH,TACT EVQ21505R

SW2208 BZ612010 0504101T34 SWITCH,TACT EVQ21505R

SW2209 BZ612010 0504101T34 SWITCH,TACT EVQ21505R

SW2210 BZ612010 0504101T34 SWITCH,TACT EVQ21505R

VARIABLE RESISTORS

VR401 BZ210218 V1K63H3BTE VOLUME,SEMI FIXED NVG6TLTAB222

VR502 BZ210024 V1163L2BTC VOLUME,SEMI FIXED EVNCYAA03BY2

P.C.BOARD ASSEMBLIES

PCB010 AE002913 A5L9019010 PCB ASS'Y VMB281B

PCB110 AE002914 A5L9019110 PCB ASS'Y TCB413B

MISCELLANEOUS

B501 BZ310122 024HT03563 CORE,BEADS W4BRH3.5X6X1.0X2

B503 BZ310121 024HT03553 CORE,BEADS W5RH3.5X5X1.0

B505 BZ310121 024HT03553 CORE,BEADS W5RH3.5X5X1.0

B602 BZ310121 024HT03553 CORE,BEADS W5RH3.5X5X1.0

BL001 BZ310014 023C00022A COIL,BALUN HPN-01

BT101 AE000012 1412004008 BATTERY,MANGAN R03(AB)E_2P_G

BT102 AE000012 1412004008 BATTERY,MANGAN R03(AB)E_2P_G
! CD501 AD300685 120R414903 CORD,AC BUSH 0R414903

CD503 BZ614133 069X620040 CONNECTOR JM-2BK-61

CD801 BZ614378 06CU823001 CORD,CONNECTOR CU823001

CD851 BZ614362 WHL6042038 FLAT CABLE AWM2468 AWG26 10C BLACK 420MM

CD852 BZ614100 06CH01408A CORD,EIS CONNECTOR CH01408A

CD853 BZ614317 06CH012101 CORD,CONNECTOR CH012101

CF601 BZ613031 1029045R7G FILTER,SAW TSF5229P3

CF602 AD300513 1012T04702 FILTER,CERAMIC TRAP MKT47.3MC110P-TF

CF603 AD301647 1012T4R520 FILTER,CERAMIC SFSRA4M50CF00-A0

CF604 AD301648 1012T4R519 FILTER,CERAMIC TRAP TPSRA4M50C00-A0

J3-3

ELECTRICAL REPLACEMENT PARTS LIST

Location No. TSB P/N Reference No. Description

MISCELLANEOUS

CP351 AD301329 069E260659 CONNECTOR PCB SIDE 00_8283_0611_00_00

CP352 BZ614205 06CU123201 CORD,CONNECTOR CU123201

CP354 AE002915 06CH121701 CORD,CONNECTOR CH121701

CP401 BZ614303 069S450089 CONNECTOR PCB SIDE A1561WV2-A5P

CP502 AD300687 069S420110 CONNECTOR PCB SIDE A1561WV2-2P

CP503 BZ614137 069X620030 CONNECTOR PCB SIDE RE-H022TD-1130

CP504 BZ614444 069D01001A CONNECTOR PCB SIDE 003P-2100

CP505 BZ614444 069D01001A CONNECTOR PCB SIDE 003P-2100

CP801 BZ614269 069S320010 CONNECTOR PCB SIDE A2361WV2-2P

CD4001 BZ614373 122F061502 CORD,JUMPER 2F061502

CP1001 BZ614289 06972C0010 CONNECTOR PCB SIDE TMC-J12P-B2

CP1003 BZ614138 0694240139 CONNECTOR PCB SIDE 173979-4

CP4001 BZ614054 0697240600 CONNECTOR PCB SIDE TOC-C04X-B1

CP4002 BZ614050 069J760029 CONNECTOR PCB SIDE IMSA-9604S-06Z14

CP4003 AD301649 067U002019 WIRE HOLDER B2013H02-2P

CP851A BZ614273 067U010049 WIRE HOLDER B2013H02-10P

CP851B BZ614273 067U010049 WIRE HOLDER B2013H02-10P

CUS011 BZ710279 800WFAA006 CUSHION A

CUS013 BZ710149 800WFAA008 CUSHION C

EL001 BZ614043 124116281A EYE LET XRY16X28BD

EL002 BZ614044 124120301A EYE LET XRY20X30BD
! F501 BZ614504 081PC05005 FUSE 51MS050L
! FB401 BZ310164 043219014F TRANSFORMER,FLYBACK FQI-20B001R

FH501 AE002634 06710T0009 HOLDER,FUSE EYF-52BCY

FH502 AE002634 06710T0009 HOLDER,FUSE EYF-52BCY

OS2201 BZ614199 077Q004017 REMOTE RECEIVER PIC-37243SR
! SP351 AD301709 070C133017 SPEAKER SG08G35BRA

SP353 AD301709 070C133017 SPEAKER SG08G35BRA
! TH501 BZ410079 DF5EL3R0A0 DEGAUSS ELEMENT ZPB45BL3R0A

TM101 AE002788 076D0JG010 TRANSMITTER ORV203N5703003
! TU601 AD301652 0145K00062 TUNER,VHF-UHF TECC1040PG38W
! V801 AE002916 098Y210453 CRT W/DY A51LZM10X20N45

X602 AD301653 100DT3R531 CRYSTAL HC-49/U

X1001 AE000107 100CT01207 CRYSTAL HC-49/U-S

X1002 BZ613006 100DA32R01 CRYSTAL DT-26

X4001 BZ613017 100CT3R502 CRYSTAL HC-49/U

RESISTOR

CAPACITORS

RC................... CARBON RESISTOR

CC................... CERAMIC CAPACITOR

CE................... ALUMI ELECTROLYTIC CAPACITOR

CP................... POLYESTER CAPACITOR

CPP.................. POLYPROPYLENE CAPACITOR

CPL.................. PLASTIC CAPACITOR

CMP................... METAL POLYESTER CAPACITOR

CMPL................ METAL PLASTIC CAPACITOR

CMPP................ METAL POLYPROPYLENE CAPACITOR

J3-4

TOSHIBA CORPORATION

1-1, SHIBAURA 1-CHOME, MINATO-KU, TOKYO 105-8001, JAPAN