Toshiba MV13N2W Owner’s Manual

OWNER'S MANUAL

TOSHIBA

TELEVISION/VCR COMBINATION

MV13N2/W MV19N2/W

_o oooooooo@

If you purchase a universal remote control from your local retailer, please

I ATTENTION

contact the remote manufacturer for the required programming code.

When shipped from the factory, the TV/CATV menu option is set to the "CATV" (Cable Television) mode.

I TV/CATV MODE SELECTION

If not using CATV, set this menu option to the "TV" position.

VgS] Before operating the unit, please read this manual thoroughly.

CAUTION

CAUTION: TO REDUCETHE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle is

intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of

electric shock.

The exclamation point within an equilateral triangle isintended to alert the user to

the presence of important operating and

maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR

WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device,

CAUTION: Changes or modifications not expressly approved by the party responsible for compliance with the

WARNING: Unauthorized recording of copyrighted television programs, films, video cassettes and other materials

MOISTURE.

pursuant to Part 15 of the FCC (Federal Communications Commission) Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one

or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the distance between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC (Federal Communications Commission) Rules could void the user's authority to operate this

equipment.

that third party copyrights and other rights are not violated.

may infringe the rights of copyright owners and be contrary to copyright laws.

IMPORTANT SAFEGUARDS

1. READ INSTRUCTIONS All the safety and operating instructions should be read before the unit is operated.

2. RETAIN INSTRUCTIONS The safety and operating instructions should be retained for future reference.

3. HEED WARNINGS All warnings on the unit and in the operating instructions should be adhered to.

4. FOLLOW INSTRUCTIONS All operating and use instructions should be followed.

5. CLEANING

Unplug this unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning the exterior cabinet only.

6. ATTACHMENTS The manufacturer of this unit does not make any recommendations for attachments, as they may cause haz-

ards.

7. WATER AND MOISTURE

Do not use this unit near water. For example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. PORTABLECARTWARNING

8. ACCESSORIES (symbolprovidedby RETAC)

DO not place this unit on an unstable cart, stand, tripod, bracket, or table. _ll_

The unit may fall, causing serious injury, and serious damage to the unit.

8A. An appliance and cart combination should be moved with care. Quick stops,

excessive force, and uneven surfaces may cause the appliance and cart

combination to overturn.

9. VENTILATION S3126A

Slots and openings in the cabinet back or bottom are provided for ventilation, and to ensure reliable operation of

the unit, and to protect it from overheating. These openings must not be blocked or covered. The openings should never be blocked by placing the unit on a bed, sofa, rug, or other similar surface. This unit should never

be placed near or over a radiator or heat source. This unit should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to.

10. POWER SOURCE This unit should be operated only from the type of power source indicated on the rating plate. If you are not sure

of the type of power supply to your home, consult your appliance dealer or local power company. For units

intended to operate from battery power, or other sources, refer to the respective pages on this Owner's Manual

for their operating instructions.

11. GROUNDING OR POLARIZATION This unit is equipped with a polarized alternating-current line plug (a plug having one blade wider than the other).

This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your

obsolete outlet. Instead of the polarized alternating-current line plug, your unit may be equipped with a 3-wire

grounding-type plug (a plug having a third (grounding) pin). This plug will only fit into a grounding-type power

outlet. This too, is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to

replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.

IMPORTANT SAFEGUARDS (CONTINUED)

12. POWER-CORD PROTECTION

Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.

13. LIGHTNING To protect your unit from a lightning storm, or when it is left unattended and unused for long periods of time,

unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the unit due to lightning and power line surges.

14. POWER LINES An outside antenna system should not be located in the vicinity of overhead power lines, other electric light or

power circuits, or where it can fall onto or against such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits, as contact

with them might be fatal.

15. OVERLOADING

Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.

16. OBJECT AND LIQUID ENTRY

Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short out

parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit.

17. OUTDOOR ANTENNA GROUNDING

If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is grounded

to provide some protection against voltage surges and built-up static charges, Section 810 of the National

Electrical Code (NEC), ANSI/NFPA 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

18. SERVICING Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage

or other hazards. Refer all servicing to qualified service personnel.

For example:

a. When the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the unit. c. If the unit has been exposed to rain or water. d. If the unit does not operate normally by following the operating instructions. Adjust only those controls that are

covered by the operating instructions, as an improper adjustment of other controls may result in damage and

will often require extensive work by a qualified technician to restore the unit to its normal operation. e. If the unit has been dropped or the cabinet has been damaged. f. When the unit exhibits a distinct change in performance, this indicates a need for service.

19. REPLACEMENT PARTS

When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original part.

Unauthorized substitutions may result in fire, electric shock or other hazards.

20, SAFETY CHECK

Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to

determine that the unit is in proper operating condition.

21. HEAT The product should be situated away from heat sources such as radiators, heat registers, stoves, or other

products (including amplifiers) that produce heat.

22. NOTE TO CATV SYSTEM INSTALLER This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides

guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

EXAMPLE OF ANTENNA GROUNDING AS PER THE

NATIONAL ELECTRICAL CODE

.,_.......-t ANTENNA LEAD IN WIRE

GROUND CLA

, z I /" ,,,,)K ANTENNA DISCHARGE UNIT

/ 1 NECSECT'ON81020)

L..............ELEC-i'RIC_ISIERM_FCE_ _] _GROUNDING CONDUCTORS

_"",,,,,,,,,,,,_ ...... _ (NEC SECTION 810-21)

IkEC-NATCNALELECT_ _ _:_:s_L:v_cESGRoUNDING

ELECTRODE SYSTEM

$2898A (NEC ART 250, PART H)

FEATURES

Color TV With Video Cassette Recorder - Unique space saving design combines a color TV and avideo cassette

recorder.

High Quality Picture Technology - This TV/VCR equipped "HQ" incorporates VHS High Quality technology. A built-in detail enhancer is used to boost the recorded signal and provide picture quality during playback. It is compatible with other VHS

video cassette recorders.

181 Channel Tuner - Receives standard VHF and UHF broadcast channels and up to 113 cable channels. The actual number of channels received depends upon channel reception in your area or your cable system.

Closed Caption Decoder With Full Text Mode - Displays text captions or full screen text on the screen for hearing impaired viewers.

8-Programs/I-Month Programmable Timer With Everyday/Every Week Capability - The built-in timer allows automatic absentee recording of up to 8 TV programs within 1 month. It is also possible to record a program which is broadcast at the same time everyday or every week.

Automatic Clock Set - Once your TV/VCR is plugged into the AC outlet, it automatically sets the correct date and time.

On-Screen TV Display And VCR Programming - When you select a channel or make other changes, the TV will show an indicator on the screen for a few seconds. Timer recording can be programmed and confirmed on the screen.

Picture Adjustments Using The Remote Control - The On-Screen display allows remote control adjustment of BRIGHT- NESS, CONTRAST, COLOR, TINT and SHARPNESS.

Automatic Playback/Rewind-Stop-Eject - When loading a cassette tape without the erase prevention tab, this TV/VCR will automatically play back the cassette tape at the correct speed. When a tape reaches its end during play-back, recording

(except during OTR and Timer Record) and fast forward, it will automatically stop, rewind, stop and eject the tape.

Programmable ON/OFF Timer - Allows you to automatically turn on or off the TV/VCR at a set time.

Programmable TV Sleep Timer - Operable from the remote control, the TV can be programmed up to 120 minutes to turn

off automatically.

Automatic Repeat Play System - When Auto Repeat option is turned on, the TV/VCR will automatically play back the same cassette tape repeatedly.

One-touch Timer Recording (OTR) - Simply by pressing the REC buttons, the TV/VCR can be programmed for up to 6 hours of recording with an immediate start.

Front Audio/Video Input Jacks - Input jacks for other video device or playback purpose.

Skip Search - When the SKIP SEARCH button on the remote control is pressed during playback, the TV/VCR will auto- matically search forward in 30 second increments to a maximum of 3 minutes with each press of the SKIP SEARCH button, and then return to normal playback.

2 Speed Picture Search - 3 or 5 times normal speed in SP mode (9X or 15X in SLP).

2 Speed Record Playback - Records and plays two tape speeds (SP, SLP).

Real Time Tape Counter With Zero Return - The counter displays the real tape time and the zero return can be used to return the tape to a preselected position (00:00:00) while the counter can be used to locate programs.

Digital Auto Tracking - Automatically adjusts tracking during playback for the best possible picture.

On-Screen 3 Language Display - You can select one of 3 languages, English, Spanish or French for on-screen programming.

V-Chip - The V-Chip function can read the rating of a TV program or movie content if the program isencoded with this information. V-Chip will allow you to set a restriction level.

TABLE OF CONTENTS

Please read the descriptions and operating procedures contained in this Owner's Manual prior to operating your new TV/VCR.

/ \

li)i jiii:iii¸

SAFETY PRECAUTIONS ....................................................................................................................................... 6

LOCATION OF CONTROLS ................................................................................................................................... 8

REMOTE CONTROL .............................................................................................................................................. 9

ANTENNA CONNECTIONS ................................................................................................................................... 11

CABLE TV CONNECTIONS ................................................................................................................................. 13

SETTING THE LANGUAGE ................................................................................................................................. 14

AUTO CLOCK SETTING ...................................................................................................................................... 15

MANUAL CLOCK SETTING ................................................................................................................................. 17

TV OPERATION .................................................................................................................................................... 18

TO MEMORIZE CHANNELS ................................................................................................................................ 22

SETTING THE V-CHIP ......................................................................................................................................... 25

TO SET THE ON TIMER ....................................................................................................................................... 29

TO SET THE OFF TIMER ..................................................................................................................................... 30

PICTURE CONTROL ADJUSTMENTS ................................................................................................................ 31

LOADING AND UNLOADING AVIDEO CASSETTE ............................................................................................ 33

PLAYBACK ........................................................................................................................................................... 35

SPECIAL PLAYBACK ........................................................................................................................................... 37

RECORDING A TV PROGRAM ............................................................................................................................ 39

ONE-TOUCH TIMER RECORDING (OTR) .......................................................................................................... 41

TIMER RECORDING ............................................................................................................................................ 42

OTHER FUNCTIONS FOR THE TIMER RECORDING ........................................................................................ 44

USING THE REAL TIME TAPE COUNTER .......................................................................................................... 45

USING ZERO RETURN ........................................................................................................................................ 46

DUPLICATING A VIDEO TAPE ............................................................................................................................. 47

PROBLEM AND TROUBLESHOOTING GUIDE ................................................................................................... 48

RECEPTION DISTURBANCES ............................................................................................................................ 50

VIDEO HEAD CLEANING ..................................................................................................................................... 51

SPECIFICATIONS ................................................................................................................................................ 51

LIMITED WARRANTY .......................................................................................................................................... 52

SAFETY PRECAUTIONS

MOISTURE CONDENSATION

DO NOT OPERATE ANY FUNCTIONS ON THIS UNIT FOR AT LEAST THREE HOURS WHEN MOISTURE IN

THE AIR CONDENSES ON IT. LET THE UNIT STAND WITH POWER ON (SEE BELOW).

• WHAT IS MOISTURE CONDENSATION? When a cold liquid is poured into a glass, for example, water vapor in the air will condense on the surface of

the glass. This is called moisture condensation.

• MOISTURE WILL CONDENSE ON THE UNIT IN THE FOLLOWING CASES; Head Drum

• When you move the unit from a cold to a warm place.

• After heating a cold room or under extremely humid conditions.

• WHEN YOU EXPERIENCE THE ABOVE CONDITIONS, Plug the power cord into an AC outlet, press the POWER button to turn on

and leave the unit at room temperature until moisture condensation disappears. Depending on the surrounding conditions, this may take about three hours.

If you cause a static discharge when touching the

unit, and the unit fails to function, simply unplug the unit from the wall outlet, wait a few minutes and

plug it back in. The unit should return to normal operation. 'k

Avoid extreme heat.

Video Tape

not place the unit on or near appliances which may

cause electromagnetic interference (e.g. speakers, etc). Doing so may cause erratic operation of the unit including picture and/or sound distortion or noise.

Avoid extreme moisture and dust.

Avoid extreme cold.

The ventilation holes prevent overheating. Do not

block or cover these holes. Especially avoid covering the holes with soft materials such as cloth or paper.

Donotinsertfingersoranyotherobjectsintothe

cassetteloadingslot.Donotspraycleanerorwax directlyontheunitoruseforcedairtoremovedust.

_Avoid places subject to strong vibration. Use in

a horizontal (flat) position only.

"-Keeptheunitawayfromflowervases,sinks,etc.

Ifliquidsshouldbespilledintotheunit,serious

_VVhen you finish operating the unit, always unload

the cassette and turn off the power.

damagewillresult.Ifyouspillanyliquidsintothe unit,unplugtheACpowercordimmediatelyand consultqualifiedservicepersonnelbeforeattempt-

ingtouseitagain.,_.;_.

When you leave your home for a long time, unplug

the AC power cord.

_'-Toprotect the unit from a lightning storm, unplug the"

AC power cord from the wall outlet and disconnect the antenna.

POWER SOURCE

TO USE AC POWER

Use the AC polarized line cord provided for operation on AC. Insert the AC cord plug into a standard 120V 60Hz polarized AC outlet.

NOTES:

• Never connect the AC line cord plug to anything other than the specified voltage (120V 60Hz). Use the attached power cord only.

• If the polarized AC cord does not fit into a nonpolarized AC outlet,

do not attempt to file or cut the blade. It is the user's responsibility to have an electrician replace the obsolete outlet.

• If you cause a static discharge when touching the unit, and the unit fails to function, simply unplug the unit from the AC outlet, wait

a few minutes, and plug it back in. The unit should return to normal operation.

• If the AC cord plug is plugged in for the first time, wait for about 5 seconds before pressing the POWER button.

Wider Hole

and B_

Polarized AC Cord Plug (One blade is wider than the other)

AC Outlet

LOCATION OF CONTROLS

FRONT

! \

3o ;_'ooooooo@

(MV13N2/W)

3 4

LII

8 9 10 11 12 13 14

REAR

15 16

DESCRIPTION OF CONTROLS

FRONT:

1. Cassette Loading Slot - To insert or remove a

video tape.

2. POWER Button - Press to turn the TV/VCR on or off.

3. TIMER REC Indicator - Lights when the unit is in

the Timer Record Mode.

4. REC Indicator - Lights up when the TV/VCR is

recording.

5. PLAY Button - Press to play a prerecorded tape.

6. REW (Rewind) Button - In the Stop mode, this

button rapidly winds the tape backwards. In the Play mode, this button activates reverse search.

7. PHONE Jack - Plug monaural headphones or an earphone with an 1/8" miniplug into this jack for private listening.

8. Remote Sensor - Signals from the Remote Control are received here.

9. REC Button - Press once to start normal recording. Additional presses activate One-touch Timer

Recording.

10. VOLUME •/• Buttons - Press to raise or lower the volume of the sound.

11. CHANNEL • / • Buttons - Press to select a

channel for viewing or recording.

12. STOP/EJECT Button - Press once to stop the tape

in any mode. Press again to eject the tape.

13. FF (Fast Forward) Button - In the Stop mode, this

button rapidly winds the tape forward. In the Play mode, this button activates forward search.

14. AUDIO/VIDEO IN Jacks -Audio and video signal

cables from an external source can be connected here.

REAR:

15. UHF/VHF Antenna Jack - Connect the 75 ohm

coaxial cable from the antenna or Cable TV service

to this jack.

16. AC Power Cord - Connect to a 120V, 60Hz outlet.

REMOTE CONTROL

_ PowEn

C) 0 C2J _ --

_J 8

_10 _11

_13

5--@@_

DESCRIPTION OF

1. CLOSED CAPTION Button - Switches between Caption, Text and TV modes for Closed-Captioned programs.

2. Direct Channel Selection Buttons (0-9) - Allows direct access to any channel.

3. CALL Button - Displays the present time/day of the week, channel, counter, speed selection (and VCR

mode if VCR is operating) on the TV screen.

4. MENU Button - Press to display the On-Screen menu function.

5. PROGRAM Button - Press to confirm the programmed timer recording and ON/OFF timer.

6. PLAY Button - Press to play a prerecorded tape.

7. EJECT Button - Press to eject the tape.

8. POWER Button - Press to turn the TV/VCR on. Press again to turn the TV/VCR off.

9. SKIP SEARCH Button - Press in the playback mode to search forward in 30 second increments to a maximum of 3 minutes.

10. ZERO RETURN Button - Use to stop the tape when the counter reaches 00:0O:OO.

11. CANCEL Button - Used to clear the selected program and to move the cursor backward.

12. SP/SLP Button - Sets the tape speed for recording.

13. CHANNEL +/- Buttons - Press the + button to change to a higher numbered channel set into memory.

Press the - button to change to a lower numbered

channel set into memory.

14. TIMER REC Buttons - Used to set the TV/VCR to start

recording at a preset time.

15. FF (Fast Forward) Button - In the Stop mode, this

button rapidly winds the tape forward. In the Play mode,

this button activates forward search.

16 _

<3)_ _-_"_

_) _) _) 0

(Z) Q) (_) _ 23

17_

19_

20--

_ (_ _ --24

_ 27

_ 28

CONTROLS

16. SLEEP Button - Sets the TV to turn off automatically after up to 120 minutes.

17. DIGITAL TRACKING Button -Allows automatic adjustment of tracking to minimize picture noise during

playback.

18. SET/TR +/- Buttons - Used to set or adjust in the menu mode. During playback, they are used to adjust

tracking manually.

19. VOLUME +/- Buttons - Press the + button to in- crease, or the - button to decrease the volume level.

20. REC Buttons - Press both buttons at the same time once to start normal recording. Additional presses

activate One-touch Timer Recording.

21. REW (Rewind) Button - In the Stop mode, this button rapidly winds the tape backwards. In the Play mode,

this button activates reverse search.

22. INPUT SELECT Button - Switches the program for viewing between the TV/VCR and external input sources.

23. COUNTER RESET Button - Used to reset the counter to 00:0O:0O.

24. CHANNEL RETURN Button - Switches between the present channel and the last channel selected.

25. MUTE Button - Press to turn off the sound. Press again to turn the sound back on.

26. ENTER Button - Press to enter or select information for on-screen operations.

27. PAUSE/STILL Button - During recording, this button temporarily stops the tape. During playback, it stops the tape and displays a still image on the TV screen.

28. STOP Button - Press once to stop the tape.

REMOTE CONTROL (CONTINUED)

BATTERY INSTALLATION

Slide the battery compart- ment cover in the direction

of the arrow.

BATTERY PRECAUTIONS

The precautions below should be followed when using batteries in this device:

1. Use only the size and type of batteries specified.

2. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment. Reversed batteries may cause damage to the device.

3. Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones.

4. If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage.

5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture (Follow battery manufacturer's directions).

Install two "AAA" batteries, paying attention to the

polarity diagram in the battery compartment.

Replace the compartment cover.

EFFECTIVE DISTANCE OF THE REMOTE CONTROL

NOTES: • When there is an obstacle between the TV/VCR and the remote control, the remote control may not

operate.

• When direct sunlight, an incandescent lamp, fluorescent lamp or any other strong light shines on the Remote sensor of the TV/VCR, the remote operation may be unstable.

• When using the remote control, press the button at intervals of about 1 second to ensure the correct mode of operation.

ANTENNA CONNECTIONS

If you are using an indoor or outdoor antenna, follow the instructions below that correspond to your antenna system. If you are using a cable TV service (CAW), see page 13 for Cable TV connections.

Combination VHF/UHF Antenna (Single 75 ohm cable or 300 ohm twin-lead wire)

,-- _ Connect the 75 ohm cable from the combination VHF/

75 ohm Coaxial Cable

ANT,

Antenna

Jack

300-75 ohm Matching

Transformer

ANT.

-®

Antenna

Jack

Combination VHF/UHF Antenna (Separate VHF and UHF 300 ohm twin-lead wires)

300-75 ohm

ANT. Transformer

Matching

UHF antenna to the Antenna Jack.

If your combination VHF/UHF antenna has a 300 ohm twin-lead wire, the use of the 300-75 ohm Matching Transformer may be necessary.

Connect the UHF 300 ohm twin-lead wire to the Combiner (not supplied). Connect the VHF 300 ohm

twin-lead wire to the 300-75 ohm Matching Trans- former. Attach the Transformer to the Combiner, then attach the Combiner to the Antenna Jack.

Combiner _[_._

UNF 300 ohm "_ _:

VHF 300 ohm

Separate VHF/UHF Antennas (75 ohm VHF cable and 300 ohm UHF twin-lead wires)

,-- -,, Connect the VHF 75 ohm cable and UHF 300 ohm

twin-lead wire to the Combiner (not supplied). Attach the Combiner to the Antenna Jack.

ANT.

Ant&na FZSohm

ack

ANTENNA CONNECTIONS (CONTINUED)

INDOOR ANTENNA (NOT SUPPLIED)

Insert a twin-lead telescopic antenna (not supplied) into the mounting hole on the back of the cabinet until it locks into place. Attach the antenna plug to the antenna jack. Adjust the length and angle of the antenna rods to receive the best possible picture.

CABLE TV CONNECTIONS

This TV/VCR has an extended tuning range and can tune most cable channels without using a Cable TV converter box. Some cable companies offer "premium pay channels" in which the signal is scrambled. Descrambiing these signals for normal viewing requires the use of a descrambier device which is gener- ally provided by the cable company.

FOR SUBSCRIBERS TO BASIC CABLE TV SERVICE

For basic cable service not requiring a Converter/Descrambler box, connect the CATV 75 ohm Coaxial Cable directly to the Antenna Jack

ANT.

75 ohm Antenna Coaxial Cable Jack

FOR SUBSCRIBERS TO SCRAMBLED CABLE TV SERVICE

If you subscribe to a cable TV service which requires the use of a Converter/Descrambler box, connect the incoming

75 ohm Coaxial Cable to the Converter/Descrambler box. Using another 75 ohm Coaxial Cable, connect the output jack of the Converter/Descrambler box to the Antenna Jack on the TV/VCR. Follow the connections shown below. Set the

TV/VCR to the output channel of the Converter/Descrambler box (usually channel 3 or 4) and use the Converted Descrambler box to select channels.

Incoming

75 ohm 75 ohm Cable to CATV cable TV/VCR

==I Converter/Descrambler I

on the back of the TV/VCR.

ANT.

Antenna

Jack

FOR SUBSCRIBERS TO UNSCRAMBLED BASIC CABLE TV SERVICE WITH SCRAMBLED PREMIUM CHANNELS

If you subscribe to a cable TV service in which basic channels are unscrambled and premium channels require the use of a Converter/Descrambler box, you may wish to use a signal splitter and an A/B Switch box (available from the Cable company or an electronics supply store). Follow the connections shown below. With the switch in the "B" position, you can directly tune any nonscrambled channels on your TV/VCR. With the switch in the "A" position, tune your TV/VCR to the output of the Converter/Descrambler box (usually channel 3 or 4) and use the Converter/

Descrambler box to tune scrambled channels.

Incoming Descrambler 75 ohm 75 ohm cable

CATV cable to TV/VCR

:- litter A/B Switch

_Sp Converter/

Antenna

Jack

SETTING THE LANGUAGE

This TV/VCR can display the on screen language in English, Spanish or French. On-screen language selection (step 3) will automatically appear on the screen when you press the MENU button initially. Select the language you prefer first, then proceed with the other menu options.

Press the MENU button. Press the SET/TR + or - button to select the

SYSTEM SETUP option, then press the

ENTER button.

MENU -- SET/TR 4- ENTER

1 I1MER RECsEr I W8NIlP

I CHSETUP

_AUTO REPOT ON_FF

Press the SET/TR + or - button to select the LANGUAGE option, then press the ENTER

button.

-- SET/TR4- ENTER

j{+/_ENIER/MENU)

SY81_M SETUP

[ ,I_CLOCK SET l

| iI_AUTOCLOCK _ON OFF |

I DAYUGHT SAVING11ME

L,ST,.0,R0T,ME J

(._ENTEI_MENU)

Press the SET/TR + or - button to select the _lB desired language: English (ENGLISH), Spanish (ESPAI_IOL) or French (FRANCAIS), then press

the ENTER button•

-- SET/TR4- ENTER

LAN G UAG FJI DIOMNLANG U E

I'ENGUSH

ESPA[_OL

FRANCAJS

(+//ENTER/MENU)

Press the MENU button until the MENU screen is cleared•

lUa

AUTO CLOCK SETTING

The Auto Clock function will automatically set the built-in clock (Month, Day, Year and Time) when the TV/VCR is connected to an Antenna or Cable system and it is turned off. As the TV/VCR searches for a receivable station in your area and it receives a broadcast signal for Auto Clock, the Auto Clock needs several minutes to set itself.

AUTO CLOCK SETTING

1. Connect the Antenna or Cable system.

• If you use a cable box, turn it on.

2. Plug the AC Power cord to the AC outlet.

3. Make sure the TV/VCR is turned off.

• If you press the POWER button, the Auto Clock set is not effective.

4. Wait at least three minutes and press the POWER button.

5. Press the CALL button to check the clock on the screen.

6. if the clock is not set, check the Antenna condition. The Auto Clock may not function properly if the reception condition is not good.

AUTO CLOCK ADJUSTMENT

• If you use a cable box and you want Auto Clock adjustment to be performed, the cable box must be left on.

• The Auto Clock Adjustment is not effective when there is a difference of more than 5 minutes exists between

The Auto Clock Adjustment will be performed at 12:00 PM everyday if you turn off the TV/VCR.

the built-in clock time and the actual time.

TO SET AUTO CLOCK TO OFF

• When the AUTO CLOCK is set to OFF, the Auto Clock adjustment does not function.

• Set the clock manually (see page 17).

TO SET STANDARD TIME

In the rare event that you live within broadcast range of two stations in two different time zones, the TV/VCR may recognize the wrong station for the Auto Clock set.

To correct the situation:

1. Press the MENU button.

2. Press the SET/TR + or - button to select the SYSTEM SETUP option, then press the ENTER button.

3. Press the SET/TR + or - button to select the STANDARD TIME option, then press the ENTER button.

4. Press the SET/TR + or - button to select your time zone, then press the ENTER button.

ATLANTIC : GMT- 4 hours (GMT: Greenwich Mean Time)

EASTERN : GMT- 5 hours CENTRAL : GMT- 6 hours MOUNTAIN : GMT- 7 hours

PACIFIC : GMT- 8 hours ALASKA : GMT- 9 hours HAWAII : GMT- 10 hours AUTO : AUTO SET

5. Press the MENU button three times to return to the normal screen.

NOTE: To be able to select the standard time, the clock must first be set by "AUTO CLOCK" once.

+ 39 hidden pages