Toshiba MK5024GAY, MK6022GAX, MK4019GAX, MK3019GAX, MK4026GAX Installation Notes

TOSHIBA STORAGE DEVICE DIVISION

2.5" HDD SERIES INSTALLATION NOTES - 9.5mm Series

© 2004 Toshiba America Information Systems, Inc.

Contents subject to change without prior notice.

GENERAL DESCRIPTION

Toshiba’s 9.5mm series of 2.5" Hard Disk Drives is comprised of fast, high-capacity
drives which comply with ATA-5 standards. Toshiba recommends that these drives be
installed by a qualified technician. Additional installation hardware may be required
depending on how and or where the drive is being installed.

Specifications MK3019 MK4019 MK6022 MK4020

GAX GAX GAX GLS

HDD2172 HDD2171 HDD2184 HDD2178
Formatted Capacity 30.00GB 40.00GB 60.011GB 40.00GB
Height 9.5mm 9.5mm 9.5mm 9.5mm
# of Disks (platters) 2222
# of Data Heads 3444

MK4026 MK6026 MK8026 MK5024

GAX GAX GAX GAY

HDD2193 HDD2194 HDD2191 HDD2186
Formatted Capacity 40.007 60.011 80.012 50.020GB
Height 9.5mm 9.5mm 9.5mm 9.5mm
# of Disks (platters) 1222
# of Data Heads 2444

FUNCTIONAL SPECIFICATION

Logical Drive MK3019 MK4019 MK6022 MK4020
Parameters GAX GAX GAX GLS

HDD2171 HDD2171 HDD2184 HDD2178
# of Cylinders (user) 33,440 33,440 47,080 33,280
Bytes per Sector 512 512 512 512
LBA Sectors 58,605,120 78,140,160 11,210,240 78,140,160
Buffer Size (KBYTES) 16,384 16,384 16,384 2048
Rotation Speed (±.1%) 5400 5400 5400 4200
Transfer Rate 200.8 – 200.8 – 202.9 – 156.9 –
Internal (MBITS/sec.) 333.2 333.2 373.3 290.4
# of Cylinders (logical) 16,383 16,383 16,383 16,383
# of Heads 16 16 16 16
# of sec./Track 63 63 63 63
PIO/Ultra DMA

(MBITS/sec.) 16.6/100 16.6 16.6/100 16.6/100

Seek Time (MSEC.)

Average 12121212
Track-to-track 2222
Maximum 22 22 22 22

2.5” Hard Disk Drive Installation Notes - 9.5mm Series P/N 480040-P0 P/N 480040-P0 2.5” Hard Disk Drive Installation Notes - 9.5mm Series
01/04 01/04

Logical Drive MK4026 MK6026 MK8026 MK5024
Parameters GAX GAX GAX GAY

HDD2193 HDD2194 HDD2191 HDD2186
# of Cylinders (user) 54,000 42,480 54,000 44,160
Bytes per Sector 512 512 512 512
LBA Sectors 78,140,160 117,210,240 156,310,488 97,696,368
Buffer Size (KBYTES) 16,384 16,384 16,384 16,384
Rotation Speed (±.1%) 5400 5400 5400 7,200
Transfer Rate 233 – 446 258 – 394 233 – 446 249 – 440.5
Internal (MBITS/sec.)
# of Cylinders (logical) 16,383 16,383 16,383 16,383
# of Heads 16 16 16 16
# of sec./Track 63 63 63 63
PIO/ U ltra D M A (MBITS/sec.) 16.6/100 16.6/100 16.6/100 16.6/100
Seek Time (MSEC.)

Average 12121212
Track-to-track 2222
Maximum 22 22 22 22

UNP ACKING PR OCEDURE

Visually inspect the shipping container prior to unpacking for any signs of damage to
the container or its contents (the carrier is responsible for any damage incurred during
shipment). The drive is a precision device and even a small drop onto any surface can
cause damage. Prior to opening the anti-static bag, it is recommended that the user
ground themself with a ground strap or by touching the PC chassis or other metal object.
Remove the drive from the anti-static bag and check it for damage. Place the drive on the
anti-static bag while configuring jumpers to avoid any electrostatic discharge. Save the
shipping container and packing material for possible use later.

DRIVE CONFIGURATION

Toshiba’s 2.5" hard disk drives can be configured as either master or slave units. Master
configuration is used for all single drive applications, and master or slave configuration
(only one of each per port) is used for two drive applications. Use the information in the
following table before setting M/S drive.

Master configuration is obtained by setting jumpers B, C & D open (no jumper). Slave
configuration is obtained by setting jumpers C-D. When B-D jumper is installed, the
drive is configured as cable select. If pin 28 = Low, the drive is master. If pin 28 = High,
the drive is slave.

INSTALLATION INSTRUCTIONS

Note: Toshiba’s 2.5” HDDs are pr imarily used in notebook devices. Installation into a
notebook varies depending on the system manufacturer. Toshiba’s 2.5” drives that
are installed into a desktop PC require a 3.5” installation kit.

1. Determine mounting configuration (can be mounted in either a horizontal or verti-
cal orientation).

2. Configure drive for system application.

3. Install the I/F cable to the system’s 44 pin connector port or adapter board (if
required). Ensure Pin 1 is oriented correctly. (Pin 1 on the cable is usually identi-
fied by a red or blue stripe.)

4. Refer to applicable manuals for software installation instructions.