Page 1
TOSHIBA STORAGE DEVICE DIVISION
2.5" HDD SERIES INSTALLATION NOTES - 9.5mm Series
© 2004 Toshiba America Information Systems, Inc.
Contents subject to change without prior notice.
GENERAL DESCRIPTION
Toshiba’s 9.5mm series of 2.5" Hard Disk Drives is comprised of fast, high-capacity
drives which comply with ATA-5 standards. Toshiba recommends that these drives be
installed by a qualified technician. Additional installation hardware may be required
depending on how and or where the drive is being installed.
Specifications MK3019 MK4019 MK6022 MK4020
GAX GAX GAX GLS
HDD2172 HDD2171 HDD2184 HDD2178
Formatted Capacity 30.00GB 40.00GB 60.011GB 40.00GB
Height 9.5mm 9.5mm 9.5mm 9.5mm
# of Disks (platters) 2222
# of Data Heads 3444
MK4026 MK6026 MK8026 MK5024
GAX GAX GAX GAY
HDD2193 HDD2194 HDD2191 HDD2186
Formatted Capacity 40.007 60.011 80.012 50.020GB
Height 9.5mm 9.5mm 9.5mm 9.5mm
# of Disks (platters) 1222
# of Data Heads 2444
FUNCTIONAL SPECIFICATION
Logical Drive MK3019 MK4019 MK6022 MK4020
Parameters GAX GAX GAX GLS
HDD2171 HDD2171 HDD2184 HDD2178
# of Cylinders (user) 33,440 33,440 47,080 33,280
Bytes per Sector 512 512 512 512
LBA Sectors 58,605,120 78,140,160 11,210,240 78,140,160
Buffer Size (KBYTES) 16,384 16,384 16,384 2048
Rotation Speed (±.1%) 5400 5400 5400 4200
Transfer Rate 200.8 – 200.8 – 202.9 – 156.9 –
Internal (MBITS/sec.) 333.2 333.2 373.3 290.4
# of Cylinders (logical) 16,383 16,383 16,383 16,383
# of Heads 16 16 16 16
# of sec./Track 63 63 63 63
PIO/Ultra DMA
(MBITS/sec.) 16.6/100 16.6 16.6/100 16.6/100
Seek Time (MSEC.)
Average 12121212
Track-to-track 2222
Maximum 22 22 22 22
Page 2
2.5” Hard Disk Drive Installation Notes - 9.5mm Series P/N 480040-P0 P/N 480040-P0 2.5” Hard Disk Drive Installation Notes - 9.5mm Series
01/04 01/04
Logical Drive MK4026 MK6026 MK8026 MK5024
Parameters GAX GAX GAX GAY
HDD2193 HDD2194 HDD2191 HDD2186
# of Cylinders (user) 54,000 42,480 54,000 44,160
Bytes per Sector 512 512 512 512
LBA Sectors 78,140,160 117,210,240 156,310,488 97,696,368
Buffer Size (KBYTES) 16,384 16,384 16,384 16,384
Rotation Speed (±.1%) 5400 5400 5400 7,200
Transfer Rate 233 – 446 258 – 394 233 – 446 249 – 440.5
Internal (MBITS/sec.)
# of Cylinders (logical) 16,383 16,383 16,383 16,383
# of Heads 16 16 16 16
# of sec./Track 63 63 63 63
PIO/ U ltra D M A (MBITS/sec.) 16.6/100 16.6/100 16.6/100 16.6/100
Seek Time (MSEC.)
Average 12121212
Track-to-track 2222
Maximum 22 22 22 22
UNP ACKING PR OCEDURE
Visually inspect the shipping container prior to unpacking for any signs of damage to
the container or its contents (the carrier is responsible for any damage incurred during
shipment). The drive is a precision device and even a small drop onto any surface can
cause damage. Prior to opening the anti-static bag, it is recommended that the user
ground themself with a ground strap or by touching the PC chassis or other metal object.
Remove the drive from the anti-static bag and check it for damage. Place the drive on the
anti-static bag while configuring jumpers to avoid any electrostatic discharge. Save the
shipping container and packing material for possible use later.
DRIVE CONFIGURATION
Toshiba’s 2.5" hard disk drives can be configured as either master or slave units. Master
configuration is used for all single drive applications, and master or slave configuration
(only one of each per port) is used for two drive applications. Use the information in the
following table before setting M/S drive.
Master configuration is obtained by setting jumpers B, C & D open (no jumper). Slave
configuration is obtained by setting jumpers C-D. When B-D jumper is installed, the
drive is configured as cable select. If pin 28 = Low, the drive is master. If pin 28 = High,
the drive is slave.
INSTALLATION INSTRUCTIONS
Note: Toshiba’s 2.5” HDDs are pr imarily used in notebook devices. Installation into a
notebook varies depending on the system manufacturer. Toshiba’s 2.5” drives that
are installed into a desktop PC require a 3.5” installation kit.
1. Determine mounting configuration (can be mounted in either a horizontal or verti-
cal orientation).
2. Configure drive for system application.
3. Install the I/F cable to the system’s 44 pin connector port or adapter board (if
required). Ensure Pin 1 is oriented correctly. (Pin 1 on the cable is usually identi-
fied by a red or blue stripe.)
4. Refer to applicable manuals for software installation instructions.
Page 3
FIGURE 1 – 2.5" HDD JUMPER LOCATIONS
JUMPER P28 DRIVE
No Jumper - Master Drive
C-D Jumper - Slave Drive
B-D Jumper LOW Master Drive
B-D Jumper HIGH Slave Drive
A-B Jumper - Slave Drive/
A-C Jumper - Prohibit
FIGURE 2 – MOUNTING HOLE LOCATIONS
INSTALLATION INSTRUCTIONS
Note: Toshiba’s 2.5” HDDs are pr imarily used in notebook devices. Installation into a
notebook varies depending on the system manufacturer. Toshiba’s 2.5” drives that
are installed into a desktop PC require a 3.5” installation kit.
1. Determine mounting configuration (can be mounted in either a horizontal or vertical orientation).
2. Configure drive for system application.
3. Install the I/F cable to the system’s 44 pin connector port or adapter board (if
required). Ensure Pin 1 is oriented correctly. (Pin 1 on the cable is usually identified by a red or blue stripe.)
4. Refer to applicable manuals for software installation instructions.
43
KEY
PIN 20
1CA
DB
JUMPERS
INTERFACE
CONNECTOR
MOUNTING HOLES
Page 4
2.5” Hard Disk Drive Installation Notes - 9.5mm Series P/N 480040-P0 P/N 480040-P0 2.5” Hard Disk Drive Installation Notes - 9.5mm Series
01/04 01/04
2.5" HDD SERIES INSTALLATION NOTES - 9.5mm Series
GENERAL DESCRIPTION
Toshiba’s 9.5mm series of 2.5" Hard Disk Drives is comprised of fast, high-capacity
drives which comply with ATA-5 standards. Toshiba recommends that these drives be
installed by a qualified technician. Additional installation hardware may be required
depending on how and or where the drive is being installed.
Specifications MK3019 MK4019 MK6022 MK4020
Formatted Capacity 30.00GB 40.00GB 60.011GB 40.00GB
Height 9.5mm 9.5mm 9.5mm 9.5mm
# of Disks (platters) 2222
# of Data Heads 3444
Formatted Capacity 40.007 60.011 80.012 50.020GB
Height 9.5mm 9.5mm 9.5mm 9.5mm
# of Disks (platters) 1222
# of Data Heads 2444
FUNCTIONAL SPECIFICATION
Logical Drive MK3019 MK4019 MK6022 MK4020
Parameters GAX GAX GAX GLS
# of Cylinders (user) 33,440 33,440 47,080 33,280
Bytes per Sector 512 512 512 512
LBA Sectors 58,605,120 78,140,160 11,210,240 78,140,160
Buffer Size (KBYTES) 16,384 16,384 16,384 2048
Rotation Speed (±.1%) 5400 5400 5400 4200
Transfer Rate 200.8 – 200.8 – 202.9 – 156.9 –
Internal (MBITS/sec.) 333.2 333.2 373.3 290.4
# of Cylinders (logical) 16,383 16,383 16,383 16,383
# of Heads 16 16 16 16
# of sec./Track 63 63 63 63
PIO/Ultra DMA
(MBITS/sec.) 16.6/100 16.6 16.6/100 16.6/100
Seek Time (MSEC.)
Average 12121212
Track-to-track 2222
Maximum 22 22 22 22
CABLING INFORMATION
DRIVE INTERFACE SIGNALS
PIN SIGNAL PIN SIGNAL
1 -RESET 2 GROUND
3 DD 7 4 DD 8
5 DD 6 6 DD 9
7 DD 5 8 DD 10
9 DD 4 10 DD 11
11 DD 3 12 DD 12
13 DD 2 14 DD 13
15 DD 1 16 DD 14
17 DD 0 18 DD 15
19 GROUND 20 KEY
21 DMARQ 22 GROUND
23 -DIOW 24 GROUND
STOP
25 -DIOR 26 GROUND
-DMARDY
HSTROBE
27 IORDY 28 CSEL
-DMARDY
-DSTROBE
29 -DMACK 30 GROUND
31 INTRQ 32 - IOCS16
33 DA1 34 - PDIAG
35 DA0 36 DA 2
37 - CS0 38 - CS1
39 - DASP 40 GROUND
41 +5V (LOGIC) 42 +5V (MOTOR)
43 GROUND 44 RESERVED
Note: Symbol (–) in front of signal indicates negative logic.
TECHNICAL SUPPORT
Should you require technical support, contact your computer distributor . If your distributor
is unable to answer your questions, have them call Toshiba Storage Device Di vision T echnical Support, on your behalf.
TOSHIBA - STORAGE DEVICE DIVISON TECHNICAL SUPPORT
PHONE: 503/615-4364 FAX: 503/615-4379
EMAIL: [email protected]
You can also visit Toshiba’s web site at: http://www.sdd.toshiba.com
Loading...