Toshiba M100 User Manual

Satellite M100

TOSHIBA
Satellite M100 Series
User's Manual

Copyright

© 2006 by TOSHIBA Corporation. All rights reserved. Under copyright law,
this manual cannot be reproduced in any form without the prior written
permission of TOSHIBA. No patent liability is assumed, with respect to the
use of the information contained herein.

TOSHIBA Satellite M100 Series Portable Personal Computer User's Manual

First edition January 2006
Ownership and copyright of music, video computer programs, databases,

etc. are protected by the copyright laws. These copyrighted materials may
be copied for private use at home only. If, beyond the limitation above, you
copy (including to transform data formats) or modify these materials,
transfer them or distribute them via the Internet without approval of
copyright owners, you may be subject to claims for compensation for
damage and/or criminal penalities due to infringements of copyrights or
personal rights. Please remember to observe the copyright laws when you
use this product to copy the copyrighted works or perform other actions.
Please note that you may infringe the owner's rights protected by the
copyright laws if you use the screen mode switching functions (e.g.Wide
mode, Wide Zoom mode, etc.) of this product to display enlarged images/
video at coffee shops or hotels for the purposes of profits or providing these
to the public.

Disclaimer

This manual has been validated and reviewed for accuracy. The instructions
and descriptions it contains are accurate for the Satellite M100 series
Portable Personal Computers at the time of this manual’s production.
However, succeeding computers and manuals are subject to change
without notice. TOSHIBA assumes no liability for damages incurred directly
or indirectly from errors, omissions or discrepancies between the computer
and the manual.

Trademarks

IBM is a registered trademark and IBM PC, OS/2, and PS/2 are trademarks
of International Business Machines Corporation. Celeron, Intel, Intel
SpeedStep, and Pentium are trademarks or registered trademarks of Intel
Corporation or its subsidiaries in the United States and other countries.

MS-DOS, Microsoft, Windows and DirectX are registered trademarks of
Microsoft Corporation.

Centronics is a registered trademark of Centronics Data Computer
Corporation. Photo CD is a trademark of Eastman Kodak.

Bluetooth is a trademark owned by its proprietor and used by TOSHIBA
under license.

iLINK is a trademark of Sony Corporation.

ii Satellite M100

Other trademarks and registered trademarks not listed above may be used
in this manual.

TruSurround XT, WOW HD, Circle Surround Xtract, SRS and symbol
are trademarks of SRS Labs, Inc.

TruSurround XT, WOW HD, Circle Surround Xtract, TruBass, SRS 3D,
Definition and FOCUS technologies are incorporated under license from
SRS Labs, Inc.

Macrovision License of Notice

This product incorporates copyright protection technology that is protected
by methods and claims of certain U.S. patents and other intellectual rights
owned by Macrovision Corporation, and other rights owners. Use of this
copyright protection technology must be authorized by Macrovision
Corporation and is intended for home and other limited viewing uses only
unless authorized by Macrovision Corporation. Reverse engineering of
disassembly is prohibited.

Safety Instructions

Use the following safety guidelines to help protect yourself and your
computer.

When Using Your Computer

Do not operate your portable computer for an extended period of time with
the base resting directly on your body. With extended operation, heat can
potentially build up in the base. Allowing sustained contact with the skin
could cause discomfort or, eventually, a burn.

■ Do not attempt to service the computer yourself. Always follow

installation instructions closely.

■ Do not carry a battery in your pocket, purse, or other container where

metal objects (such as car keys) could short-circuit the battery terminals.
The resulting excessive current follow can cause extremely high
temperatures and may result in damage from burns.

■ Be sure that nothing rests on your AC adapter's power cable and that

the cable is not located where it can be tripped over or stepped on.

■ Place the AC adapter in a ventilated area, such as a desk top or on the

floor, when you use it to run the computer or to charge the battery. Do
not cover the AC adapter with papers or other items that will reduce
cooling; also, do not use the AC adapter while it is inside a carrying case.

■ Use only the AC adapter and batteries that are approved for use with

this computer. Use of another type of battery or AC adapter may risk
fire or explosion.

Satellite M100 iii

■ Before you connect the computer to a power source, ensure that the

voltage rating of the AC adapter matches that of the available power
source.

115 V/60Hz in most of North and South America and some Far Eastern
countries such as Taiwan.

100 V/50Hz in eastern Japan and 100 V/60Hz in western Japan.
230 V/50 Hz in most of Europe, the Middle East, and the Far East.

■ If you use an extension cable with your AC adapter, ensure that the total

ampere rating of the products that are plugged into it do not exceed the
ampere rating of the extension cable itself.

■ To help avoid the potential hazard of electric shock, do not connect or

disconnect any cables or perform maintenance or reconfiguration of this
product during an electrical storm.

■ When setting up the computer for work, place it on a level surface.

■ Do not dispose of batteries in a fire. They may explode. Check with

local authorities for disposal instructions.

■ When traveling, do not check the computer as baggage. You can put

your computer through an X-ray security machine, but never put your
computer through a metal detector. If you have the computer checked
by hand, be sure to have a charged battery available in case you are
asked to turn on the computer.

■ When traveling with the hard drive removed from the computer, wrap

the drive in a non-conducting material, such as cloth or paper. If you
have the drive checked by hand, be ready to install the drive in the
computer. Your can put the hard drive through an X-ray security
machine, but never put it through a metal detector.

■ When traveling, do not place the computer in overhead storage

compartments where it could slide around. Do not drop your computer
or subject it to other mechanical shocks.

■ Protect your computer, battery, and hard drive from environmental

hazards such as dirt, dust, food, liquids, temperature extremes, and
overexposure to sunlight.

■ When you move your computer between environments with very

different temperature and/or humidity ranges, condensation may form
on or within the computer. To avoid damaging the computer, allow
sufficient time for the moisture to evaporate before using the computer.

■ When you disconnect a cable, pull on its connector or on its strain relief

loop, not on the cable itself. As you pull out the connector, keep it evenly
aligned to avoid bending any connector pins. Also, before you connect
a cable make sure both connectors are correctly oriented and aligned.

■ Before you clean your computer, turn if off, unplug it from its power

source, and remove the battery.

■ Handle components with care. Hold a component such as a memory

module by its edges, not its pins.

iv Satellite M100

When using telephone equipment in conjunction with your computer, basic
safety precautions should always be followed to reduce the risk of fire,
electric shock and injury to persons, including the following:

■ Do not use this product near water, for example, near a bathtub, washing

bowl, kitchen sink or laundry tub, in a wet basement or near a swimming
pool.

■ Avoid using a telephone (other than a cordless type) during an electrical

storm. There may be a remote risk of electric shock from lightning.

■ Do not use the telephone to report a gas leak in the vicinity of the leak.

■ Use only the power cord indicated in this manual.

■ Replace only with the same or equivalent type battery recommended by

the manufacturer.

■ Dispose of used batteries according to the manufacturer's instructions.

■ To reduce the risk of fire, use only No. 26 AWG or larger

telecommunication line cord.

Use only the battery pack that came with the computer or an optional battery
pack. Use of the wrong battery could damage your computer.

TOSHIBA assumes no liability for any damage in such case.

Satellite M100 v

FCC information

Model Name: Satellite M100

FCC notice "Declaration of Conformity Information"

This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation.

This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:

■ Reorient or relocate the receiving antenna.

■ Increase the separation between the equipment and receiver.

■ Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

■ Consult the dealer or an experienced radio/TV technician for help.

Only peripherals complying with the FCC class B limits may be attached to
this equipment. Operation with non-compliant peripherals or peripherals
not recommended by TOSHIBA is likely to result in interference to radio and
TV reception. Shielded cables must be used between the external devices
and the computer's or expansion unit's external monitor port, parallel port,
USB port and microphone jack. Changes or modifications made to this
equipment, not expressly approved by TOSHIBA or parties authorized by
TOSHIBA could void the user's authority to operate the equipment.

EMC Regulatory Information

Contact

Address: TOSHIBA America Information Systems, Inc.

9740 Irvine Boulevard
Irvine, California 92618-1697

Telephone: [phone]

vi Satellite M100

EU Declaration of Conformity

TOSHIBA declares, that the product: Satellite M100 conforms to the
following Standards:

This product is labelled with the CE Mark in accordance with the related
European Directives, notably Electromagnetic Compatibility Directive 89/
336/EEC for the notebook and the electronic accessories including the
supplied power adapter, the Radio Equipment and Telecommunications
Terminal Equipment Directive 99/5/EEC in case of implemented
telecommunication accessories and the Low Voltage Directive 73/23/EEC
for the supplied power adapter.

CE Marking is the responsibility of TOSHIBA EUROPE GmbH,
Hammfelddamm 8, 41460 Neuss, Germany, phone [phone].

For a copy of the related CE Declaration of Conformity please refer to the
following website: http://epps.toshiba-teg.com.

Canadian Regulatory Information (Canada Only)

This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus as set out in the Radio Interference
Regulation of the Canadian Department of Communications.

Note that Canadian Department of Communications (DOC) regulations
provide, that changes or modifications not expressly approved by TOSHIBA
Corporation could void your authority to operate this equipment.

This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.

Cet appareil numérique de la class B respecte toutes les exgences du
Règlement sur le matériel brouilleur du Canada.

BSMI Notice (Taiwan Only)

Following information is only for EU-member states:

The symbol indicates that this product may not be treated as
household waste. Please ensure this product is properly
disposed as inappropriate waste handling of this product may
cause potential hazards to the environment and human health.
For more detailed information about recycling of this product,
please contact your local city office, your household waste
disposal service or the shop where you purchased the product.

This symbol may not stick depending on the country and region where you
purchased.

Satellite M100 vii

Optical Disc Drive Safety Instruction

■ Be sure to check the international precautions at the end of this section.

The optical drive that is used in this computer is equipped with a laser
device. A classification label with the following sentence is affixed to the
surface of the drive.

CLASS 1 LASER PRODUCT
LASER KLASSE 1
LUOKAN 1 LASERLAITE
APPAREIL A LASER DE CLASSE 1
KLASS 1 LASER APPARAT

The drive with the above label is certified by the manufacturer that the drive
complies with the requirement for laser product on the date of
manufacturing pursuant to article 21 of Code of Federal Regulations by the
United States of America, Department of Health & Human Services, Food
and Drug Administration.

In other countries, the drive is certified to comply with the requirement
pursant to IEC 825 and EN60825 on class 1 laser product.

This computer is equipped with one of the optical drive in the following list
according to the model

Manufacturer Type

Panasonic Communica­tions Co., LTD.

Hitachi LG Data Storage,
Inc.

Panasonic Communica­tions Co., LTD.

Panasonic Communica­tions Co., LTD.

Hitachi LG Data Storage,
Inc.

Pioneer DVD Super Multi DVR-K16TBS
TOSHIBA Samsung S tor-

age Technology
TEAC DVD Super Multi DV-W28EB
NEC DVD Super Multi ND-7550
TOSHIBA Samsung

Storage Technology

CD-RW/DVD-ROM UJDA770

CD-RW/DVD-ROM GCC-4244

DVD Super Multi UJ-850B

DVD Super Multi UJ-841

DVD Super Multi GMA-4082N

DVD-ROM SDC 2732

CD-RW/DVD-ROM TS-L462C

viii Satellite M100

International precautions

■ This drive employs a laser system. To ensure proper use of this product,

please read this instruction manual carefully and retain for future
reference. Should the unit ever require maintenance, contact an
authorized service location.

■ Use of controls, adjustments or the performance of procedures other

than those specified may result in hazardous radiation exposure.

■ To prevent direct exposure to the laser beam, do not try to open the

enclosure.

Location of the required label

Sample shown below. Location of the label on the drive and manufacturing
information may vary.

CAUTION: This appliance contains a laser system
and is classified as a "CLASS 1 LASER
PRODUCT." To use this model properly, read the
instruction manual carefully and keep this manual
for your future reference. In case of any trouble
with this model, please contact your nearest
"AUTHORIZED service station." To prevent direct
exposure to the laser beam, do not try to open the
enclosure.

Satellite M100 ix

VORSICHT: Dieses Gerät enthält ein Laser­System und ist als "LASERSCHUTZKLASSE 1
PRODUKT" klassifiziert. Für den richtigen
Gebrauch dieses Modells lesen Sie bitte die
Bedienungsanleitung sorgfältig durch und
bewahren diese bitte als Referenz auf. Falls
Probleme mit diesem Modell auftreten,
benachrichtigen Sie bitte die nächste "autorisierte
Service-Vertretung". Um einen direkten Kontakt
mit dem Laserstrahl zu vermeiden darf das Gerät
nicht geöffnet werden.

ADVARSEL: Denne mærking er anbragt
udvendigt på apparatet og indikerer, at apparatet
arbejder med laserstråler af klasse 1, hviket
betyder, at der anvendes laserstrlier af svageste
klasse, og at man ikke på apparatets yderside kan
bilve udsat for utilladellg kraftig stråling.

APPARATET BOR KUN ÅBNES AF FAGFOLK
MED SÆRLIGT KENDSKAB TIL APPARATER
MED LASERSTRÅLER!

Indvendigt i apparatet er anbragt den her gengivne
advarselsmækning, som advarer imod at foretage
sådanne indgreb i apparatet, at man kan komme
til at udsætte sig for laserstråling.

OBS! Apparaten innehåller laserkomponent som
avger laserstråining överstigande gränsen för
laserklass 1.

VAROITUS. Suojakoteloa si saa avata. Laite
sisältää laserdiodin, joka lähetää näkymätöntä
silmilie vaarallista lasersäteilyä.

CAUTION: USE OF CONTROLS OR
ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED
IN THE OWNER'S MANUAL MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.

VORSICHT: DIE VERWENDUNG VON ANDEREN
STEURUNGEN ODER EINSTELLUNGEN ODER
DAS DURCHFÜHREN VON ANDEREN
VORGÄNGEN ALS IN DER
BEDIENUNGSANLEITUNG BESCHRIEBEN
KÖNNEN GEFÄHRLICHE
STRAHLENEXPOSITIONEN ZUR FOLGE HABEN.

x Satellite M100

Modem warning notice

Conformity Statement

The equipment has been approved to [Commission Decision "CTR21"] for
pan- European single terminal connection to the Public Switched Telephone
Network (PSTN).

However, due to differences between the individual PSTNs provided in
different countries/regions the approval does not, of itself, give an
unconditional assurance of successful operation on every PSTN network
termination point.

In the event of problems, you should contact your equipment supplier in the
first instance.

Network Compatibility Statement

This product is designed to work with, and is compatible with the following
networks. It has been tested to and found to confirm with the additional
requirements conditional in EG 201 121.

Germany ATAAB AN005,AN006,AN007,AN009,AN010 and

Greece ATAAB AN005,AN006 and GR01,02,03,04
Portugal ATAAB AN001,005,006,007,011 and

Spain ATAAB AN005,007,012, and ES01
Switzerland ATAAB AN002
Norway ATAAB AN002, 005, 007 and

All other countries/
regions

Specific switch settings or software setup are required for each network,
please refer to the relevant sections of the user guide for more details.

The hookflash (timed break register recall) function is subject to separate
national type approvals. It has not been tested for conformity to national
type regulations, and no guarantee of successful operation of that specific
function on specific national networks can be given.

DE03,04,05,08,09,12,14,17

P03,04,08,10

NO 01, 02
ATAAB AN003,004

Japan regulations

Region selection

If you are using the computer in Japan, technical regulations described in
the Telecommunications Business Law require that you select the Japan
country mode.

It is illegal to use the modem in Japan with any other selection.

Satellite M100 xi

Redial

Up to two redial attempts can be made. If more than two redial attempts
are made, the modem will return Black Listed. If you are experiencing
problems with the Black Listed code, set the interval between redials at one
minute or longer.

Japan's Telecommunications Business Law permits up to two redials on
analogue telephones, but the redials must be made within a total of three
minutes.

The internal modem is approved by Japan Approvals Institute for
Telecommunications Equipment.

Pursuant to FCC CFR 47, Part 68:

When you are ready to install or use the modem, call your local telephone
company and give them the following information:

■ The telephone number of the line to which you will connect the modem

■ The registration number that is located on the device

The FCC registration number of the modem will be found on either the device
which is to be installed, or, if already installed, on the bottom of the computer
outside of the main system label.

■ The Ringer Equivalence Number (REN) of the modem, which can vary.

For the REN of your modem, refer to your computer's user's guide.

The modem connects to the telephone line by means of a standard jack
called the US:AGSMD01BATHENS.

Type of service

Your modem is designed to be used on standard-device telephone lines.
Connection to telephone company-provided coin service (central office
implemented systems) is prohibited. Connection to party lines service is
subject to state tariffs. If you have any questions about your telephone line,
such as how many pieces of equipment you can connect to it, the telephone
company will provide this information upon request.

Telephone company procedures

The goal of the telephone company is to provide you with the best service
it can. In order to do this, it may occasionally be necessary for them to make
changes in their equipment, operations, or procedures. If these changes
might affect your service or the operation of your equipment, the telephone
company will give you notice in writing to allow you to make any changes
necessary to maintain uninterrupted service.

xii Satellite M100

If problems arise

If any of your telephone equipment is not operating properly, you should
immediately remove it from your telephone line, as it may cause harm to the
telephone network. If the telephone company notes a problem, they may
temporarily discontinue service. When practical, they will notify you in
advance of this disconnection.

If advance notice is not feasible, you will be notified as soon as possible.
When you are notified, you will be given the opportunity to correct the
problem and informed of your right to file a complaint with the FCC. In the
event repairs are ever needed on your modem, they should be performed
by TOSHIBA Corporation or an authorized representative of TOSHIBA
Corporation.

Disconnection

If you should ever decide to permanently disconnect your modem from its
present line, please call the telephone company and let them know of this
change.

Fax branding

The Telephone Consumer Protection Act of 1991 makes it unlawful for any
person to use a computer or other electronic device to send any message
via a telephone fax machine unless such message clearly contains in a
margin at the top or bottom of each transmitted page or on the first page
of the transmission, the date and time it is sent and an identification of the
business, other entity or individual sending the message and the telephone
number of the sending machine or such business, other entity or individual.
In order to program this information into your fax modem, you should
complete the setup of your fax software before sending messages.

Satellite M100 xiii

Instructions for IC CS-03 certified equipment

1. NOTICE: The Industry Canada label identifies certified equipment. This
certification means that the equipment meets certain
telecommunications network protective, operational and safety
requirements as prescribed in the appropriate Terminal Equipment
Technical Requirements document(s). The Department does not
guarantee the equipment will operate to the user's satisfaction.

Before installing this equipment, users should ensure that it is
permissible to be connected to the facilities of the local
telecommunications company. The equipment must also be installed
using an acceptable method of connection.

The customer should be aware that compliance with the above
conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be coordinated by a
representative designated by the supplier. Any repairs or alterations
made by the user to this equipment, or equipment malfunctions, may
give the telecommunications company cause to request the user to
disconnect the equipment.

Users should ensure for their own protection that the electrical ground
connections of the power utility, telephone lines and internal metallic
water pipe system, if present, are connected together. This precaution
may be particularly important in rural areas.

Users should not attempt to make such connections themselves, but should
contact the appropriate electric inspection authority, or electrician, as
appropriate.

2. The user manual of analog equipment must contain the equipment's
Ringer Equivalence Number (REN) and an explanation notice similar to
the following: The Ringer Equivalence Number (REN) of the modem,
which can vary. For the REN of your modem, refer to your computer's
user's guide.

The Ringer Equivalence Number (REN) assigned to each terminal device
provides an indication of the maximum number of terminals allowed to be
connected to a telephone interface. The termination on an interface may
consist of any combination of devices subject only to the requirement that
the sum of the Ringer Equivalence Numbers of all the devices does not
exceed 5.

3. The standard connecting arrangement (telephone jack type) for this
equipment is jack type(s): US:AGSMD01BATHENS.

The IC registration number of the modem is shown below.
Canada: 4005B-ATHENS

xiv Satellite M100

Notes for Users in Australia and New Zealand

Modem warning notice for Australia

Modems connected to the Australian telecoms network must have a valid
Austel permit. This modem has been designed to specifically configure to
ensure compliance with Austel standards when the country/region selection
is set to Australia.

The use of other country/region setting while the modem is attached to the
Australian PSTN would result in your modem being operated in a non­compliant manner. To verify that the country/region is correctly set, enter
the command ATI which displays the currently active setting.

To set the country/region permanently to Australia, enter the following
command sequence:

■ AT%TE=1

■ ATS133=1

■ AT&F

■ AT&W

■ AT%TE=0

■ ATZ

Failure to set the modem to the Australia country/region setting as shown
above will result in the modem being operated in a non-compliant manner.
Consequently, there would be no permit in force for this equipment and the
Telecoms Act 1991 prescribes a penalty of $12,000 for the connection of
non-permitted equipment.

Satellite M100 xv

Notes for use of this device in New Zealand

■ The grant of a Telepermit for a device in no way indicates Telecom

acceptance of responsibility for the correct operation of that device
under all operating conditions. In particular the higher speeds at which
this modem is capable of operating depend on a specific network
implementation which is only one of many ways of delivering high quality
voice telephony to customers. Failure to operate should not be reported
as a fault to Telecom.

■ In addition to satisfactory line conditions a modem can only work

properly if:
a/ it is compatible with the modem at the other end of the call and
b/ the application using the modem is compatible with the application

at the other end of the call - e.g., accessing the Internet requires
suitable software in addition to a modem.

■ This equipment shall not be used in any manner which could constitute

a nuisance to other Telecom customers.

■ Some parameters required for compliance with Telecom's PTC

Specifications are dependent on the equipment (PC) associated with
this modem. The associated equipment shall be set to operate within
the following limits for compliance with Telecom Specifications:

a/ There shall be no more than 10 call attempts to the same number
within any 30 minute period for any single manual call initiation, and

b/ The equipment shall go on-hook for a period of not less than 30
seconds between the end of one attempt and the beginning of the next.

c/ Automatic calls to different numbers shall be not less than 5 seconds
apart.

■ Immediately disconnect this equipment should it become physically

damaged, and arrange for its disposal or repair.

■ The correct settings for use with this modem in New Zealand are as

follows:
ATB0 (CCITT operation)
AT&G2 (1800 Hz guard tone)
AT&P1 (Decadic dialing make-break ratio =33%/67%
ATS0=0 (not auto answer)
ATS10=less than 150 (loss of carrier to hangup delay, factory default of

15 recommended)
ATS11=90 (DTMF dialing on/off duration=90 ms)
ATX2 (Dial tone detect, but not (U.S.A.) call progress detect)

■ When used in the Auto Answer mode, the S0 register must be set with

a value of 3 or 4. This ensures:
(a) a person calling your modem will hear a short burst of ringing before

the modem answers. This confirms that the call has been successfully
switched through the network.

(b) caller identification information (which occurs between the first and
second ring cadences) is not destroyed.

xvi Satellite M100

■ The preferred method of dialing is to use DTMF tones (ATDT...) as this

is faster and more reliable than pulse (decadic) dialing. If for some reason
you must use decadic dialing, your communications program must be
set up to record numbers using the following translation table as this
modem does not implement the New Zealand "Reverse Dialing"
standard.

Number to be dialed: 0 1 2 3 4 5 6 7 8 9
Number to program into computer: 0 9 8 7 6 5 4 3 2 1
Note that where DTMF dialing is used, the numbers should be entered

normally.

■ The transmit level from this device is set at a fixed level and because of

this there may be circumstances where the performance is less than
optimal. Before reporting such occurrences as faults, please check the
line with a standard Telepermitted telephone, and only report a fault if
the phone performance is impaired.

■ It is recommended that this equipment be disconnected from the

Telecom line during electrical storms.

■ When relocating the equipment, always disconnect the Telecom line

connection before the power connection, and reconnect the power first.

■ This equipment may not be compatible with Telecom Distinctive Alert

cadences and services such as FaxAbility.
( NOTE THAT FAULT CALL OUT CAUSED BY ANY OF THE ABOVE

CAUSES MAY INCUR A CHARGE FROM TELECOM )

General conditions

As required by PTC 100, please ensure that this office is advised of any
changes to the specifications of these products which might affect
compliance with the relevant PTC Specifications.

The grant of this Telepermit is specific to the above products with the
marketing description as stated on the Telepermit label artwork. The
Telepermit may not be assigned to other parties or other products without
Telecom approval.

A Telepermit artwork for each device is included from which you may
prepare any number of Telepermit labels subject to the general instructions
on format, size and colour on the attached sheet.

The Telepermit label must be displayed on the product at all times as proof
to purchasers and service personnel that the product is able to be
legitimately connected to the Telecom network.

The Telepermit label may also be shown on the packaging of the product
and in the sales literature, as required in PTC 100.

The charge for a Telepermit assessment is $337.50. An additional charge
of $337.50 is payable where an assessment is based on reports against
non-Telecom New Zealand Specifications. $112.50 is charged for each
variation when submitted at the same time as the original.

An invoice for $NZ1237.50 will be sent under separate cover.

Satellite M100 xvii

Important Notice

Copyrighted works including, but not limited to music, video, computer
program, databases are protected by copyright laws. Unless specifically
permitted under applicable copyright laws, you cannot copy, modify,
assign, transmit or otherwise dispose of any copyrighted work with the
consent of the owner of the copyright.

Please take notice that unauthorized copying, modification, assignment,
transmission and disposition may be subject to claims for damages and
penalties.

General Precautions

TOSHIBA computers are designed to optimize safety, minimize strain and
withstand the rigors of portability. However, certain precautions should be
observed to further reduce the risk of personal injury or damage to the
computer.

Be certain to read the general precautions below and to note the cautions
included in the text of the manual.

Stress injury

Carefully read the Safety Instruction Manual. It contains information on
prevention of stress injuries to your hands and wrists that can be caused by
extensive keyboard use. Chapter 3, Getting Started, also includes
information on work space design, posture and lighting that can help reduce
physical stress.

Heat injury

■ Avoid prolonged physical contact with the bottom of the computer. If

the computer is used for long periods, its surface can become very
warm. While the temperature will not feel hot to the touch, if you maintain
physical contact with the computer for a long time (if you rest the
computer on your lap, for example) your skin might suffer low-heat injury.

■ If the computer has been used for a long time, avoid direct contact with

the metal plate supporting the I/O ports. It can become hot.

■ The surface of the AC adapter can become hot when in use. This

condition does not indicate a malfunction. If you need to transport the
AC adapter, disconnect it and let it cool before moving it.

■ Do not lay the AC adapter on a material that is sensitive to heat. The

material could be damaged.

Pressure or impact damage

Do not apply heavy pressure to the computer or subject it to strong impact.
Excessive pressure or impact can damage computer components or

otherwise cause malfunctions.

xviii Satellite M100

PC Card overheating

Some PC Cards can become hot with prolonged use. Overheating of a PC
Card can result in errors or instability in the PC Card operation. Also be
careful when you remove a PC Card that has been used for a long time.

Mobile phone

Use of mobile phones can interfere with the audio system. Computer
operation is not impaired but it is recommended that a distance of 30cm be
maintained between the computer and a mobile phone in use.

LCD

Over a period of time, and depending on the usage of the computer, the
brightness of the LCD screen will deteriorate. This is an intrinsic
characteristic of LCD technology. Maximum brightness is only available
when operating in AC power mode. The screen will dim when the computer
is operated on battery power and you may not be able to increase the
brightness of the screen.

CE compliance

This product and the supplied accessories are designed to observe the
related EMC (Electromagnetic Compatibility) and safety standards.
However, TOSHIBA cannot guarantee that this product still observes these
EMC standards if accessories or cables not manufactured / distributed by
TOSHIBA are connected or implemented. To avoid in general EMC
problems, the following advice should be observed:

■ Only CE marked accessories should be connected / implemented

■ Only best shielded cables should be connected

Satellite M100 xix

Working environment

This product was designed to fulfill the EMC (Electromagnetic Compatibility)
requirements for "residential, commercial and light industry environments".

The following environment is not approved:

■ Industrial Environments (e.g. environments where a with a mains voltage

of 380V threephase is being used).

In the following environments the use of this product can be restricted:

■ Medical Environments: This product is not certified as a medical product

according to the Medical Product Directive 93/42/EEC, but can be used
in office areas where the use is not restricted. Please disable the wireless
LAN or Bluetooth hardware in such areas as long this feature is not
official supported by the operator of the related medical facility.

■ Vehicle Environments: Please read operator’s manual of the vehicle

manufacturer for further restrictions of use.

■ Aircraft Environments: Please following the advices of the flight

personnel regarding restrictions of use.

Any consequences resulting from the use of this product in working
environments that are not approved or the use is restricted are not the
responsibility of Toshiba Corporation. The consequences of the use of this
product in those working environments may be:

■ Interference with other devices or machines in the nearby surrounding

area

■ Malfunction of, or data loss from, this product caused by disturbances

generated by other devices or machines in the nearby surrounding area

Furthermore, for general safety reasons, the use of this product in
environments with explosive atmospheres is not permitted.

Network connection (Class A warning)

If this product has networking capabilities and will be connected to a
network, Class A radiation limits will be observed (in accordance with
technical conventions). This means that if the product will be used in a
domestic environment, other devices in the near surrounding area may
suffer interference. Consequently, please do not use this product in such
environments (for example a living room), otherwise you could be held
responsible for any ensuing interference.

Information on the secure writing to optical disc media

Even if your software gives no indication that any problems have occurred,
you should always check to ensure that information has been successfully
stored on recordable optical media (CD-R, CD-RW and so forth).

xx Satellite M100

Wireless LAN and your Health

Wireless LAN products, like other radio devices, emit radio frequency
electromagnetic energy. The level of energy emitted by Wireless LAN
devices however is far less than the electromagnetic energy emitted by other
wireless devices such as mobile phones.

Because Wireless LAN products operate within the guidelines found in radio
frequency safety standards and recommendations, TOSHIBA believes
Wireless LAN is safe for use by consumers. These standards and
recommendations reflect the consensus of the scientific community and
result from deliberations of panels and committees of scientists who
continually review and interpret the extensive research literature.

In some situations or environments, the use of Wireless LAN may be
restricted by the proprietor of the building or responsible representatives of
the organisation. These situations may for example include:

■ Using the Wireless LAN equipment on board of aeroplanes

■ In any other environment where the risk of interference to other devices

or services is perceived or identified as harmful.

If you are uncertain of the policy that applies on the use of wireless devices
in a specific organisation or environment (e.g. airports), you are encouraged
to ask for authorisation to use the Wireless LAN device prior to turning on
the equipment.

Safety Instruction for Wireless Products

If your computer has a wireless function, all safety instructions must be read
carefully and must be fully understood, before you attempt to use it. This
manual contains the safety instructions that must be observed in order to
avoid potential hazards that could result in personal injuries or could
damage your wireless products.

Limitation of Liability

For damage occurring due to an earthquake or thunder, fire beyond our
responsibility, action by third party, other accident, intentional or accidental
mistakes by a user, misuse or use under abnormal conditions, we do not
take any responsibility.

For incidental damage (loss of business profit, business interruption, etc.)
occurring due to use or disability of the product, we do not take any
responsibility.

For damage occurring due to non observance of the contents described in
the instruction manual, we do not take any responsibility.

For damage occurring due to erroneous operation or hang up caused by
use in combination with products not related to our company, we do not
take any responsibility.

Satellite M100 xxi

Usage Restrictions

Do not use the Wireless Products for controlling the following equipment:

■ Equipment directly linked with human life corresponding to the following.

■ Medical equipment such as life support systems, equipment used in

operations, etc.

■ Exhaust systems for gases such as poisonous gas etc. and exhaust

systems for smoke.

■ Equipment that must be set up in compliance with various laws such

as the Fire Services Act, the Construction Standard Act, etc.

■ Equipment corresponding to that mentioned above.

■ Equipment linked with human safety or having a serious influence on the

safe maintenance of public function, etc., because it is not designed or
manufactured for this type of use.

■ Traffic control equipment for air, railroad, road, marine transport, etc.

■ Equipment used in atomic power plants etc.

■ Equipment corresponding to that mentioned above.

xxii Satellite M100

Warning

Turn OFF the Wireless Communication switch of wireless products in a
congested place, such as a crowded commuter train.

Keep this product away from a cardiac pacemaker at least 22cm.
Radio waves can potentially affect cardiac pacemaker operation, thereby

causing respiratory troubles.
Turn OFF the Wireless communication switch inside a medical facility or

near medical electric equipment. Do not bring medical electric equipment
close to the product.

Radio waves can potentially affect medical electric equipment, thereby
causing an accident due to malfunction.

Turn OFF the Wireless communication switch near an automatic door, fire
alarm or other automatic control equipment.

Radio waves can potentially affect automatic control equipment, thereby
causing an accident due to malfunction.

Do not turn ON the Wireless communication switch in aircraft or in places
that generate or can generate radio interference.

Radio waves can potentially affect equipment, such as that used on-board
aircraft, causing an accident due to malfunction.

You should monitor possible radio interference or other issues that may arise
with other equipment while the product is used. If any effect is noted, turn
OFF the Wireless communication switch.

Otherwise, radio waves can potentially affect other equipment, thereby
causing an accident due to malfunction.

When using the product in a car, check with the automobile dealer if the car
has an adequate electromagnetic compatibility (EMC).

Radio waves of the product can potentially hamper safe driving.
Depending on car model, the product can rarely affect car electronic

equipment if it is used in a car.

Note

Do not use this product in the following places:
Near a microwave oven or other environment which generates a magnetic

field.
Near any place or equipment that generates static electricity or radio

interference.
Depending on the environment, in a place where radio waves cannot reach

the product.

Satellite M100 xxiii

xxiv Satellite M100

Satellite M100

Table of Contents

Preface

Manual contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xxx

Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxxi

Equipment checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxxii

Chapter 1 Satellite M100 Features

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Special features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9

Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11

Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-14

Chapter 2 The Grand Tour

Front with the display closed. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Right side. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3

Left side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Back side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

Underside. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

Front with the display open . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

Keyboard Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-10

Optical Disc drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10

Chapter 3 Getting Started

Setting up your work space. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Connecting the AC adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

Opening the display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

Turning on the power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

Starting up for the first time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7

Turning off the power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7

Restarting the computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11

Creating an Express Media Player Recovery CD*. . . . . . . . . . . 3-12

Restoring the preinstalled software from

the Product Recovery disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12

User’s Manual xxv

Chapter 4 Operating Basics

Using the TouchPad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Using the Fingerprint Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

Using the internal modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10

LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13

Wireless LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14

Using optical disc drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16

Express Media Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-21

Writing CDs on a CD-RW/DVD-ROM drive . . . . . . . . . . . . . . . . 4-25

Writing CDs/DVDs on a DVD Super Multi drive s

upporting double layer disc recording. . . . . . . . . . . . . . . . . . . . 4-27

When Using WinDVD Creator 2 Platinum . . . . . . . . . . . . . . . . .4-31

RecordNow! Basic for TOSHIBA . . . . . . . . . . . . . . . . . . . . . . . . 4-33

DLA for TOSHIBA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-34

Media Care. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-35

Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-35

TV-Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-36

Setting up more than one display . . . . . . . . . . . . . . . . . . . . . . . 4-36

Cleaning the computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-37

Moving the computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-37

Chapter 5 The Keyboard

Typewriter keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

F1 ... F12 function keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2

Soft keys: Fn key combinations. . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

Hotkeys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3

Windows special keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4

Keypad overlay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-4

Generating ASCII characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

Chapter 6 Power and Power-Up Modes

Power conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

Power indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3

Battery types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-4

Care and use of the battery pack . . . . . . . . . . . . . . . . . . . . . . . . 6-5

Replacing the battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-10

TOSHIBA Password Utility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13

Power-up modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-14

Panel power off/on. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-14

System automatic Standby/Hibernation . . . . . . . . . . . . . . . . . . 6-14

Chapter 7 HW Setup

Accessing HW Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

HW Setup Window. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1

xxvi Satellite M100

Chapter 8 Optional Devices

PC Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2

SD/MMC/MS/MS Pro/xD Memory cards. . . . . . . . . . . . . . . . . . . 8-4

Memory expansion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7

Additional battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10

Additional AC adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10

Battery charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10

External monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-11

Television . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-11

i.LINK (IEEE1394). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-15

Security lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-16

Chapter 9 Troubleshooting

Problem solving process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1

Hardware and system checklist. . . . . . . . . . . . . . . . . . . . . . . . . . 9-3

TOSHIBA support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-19

Chapter 10 Disclaimers

CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1

Memory (Main System) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-2

Battery Life. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2

HDD Drive Capacity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2

LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2

Graphics Processor Unit (“GPU”) . . . . . . . . . . . . . . . . . . . . . . . 10-3

Wireless LAN/Intel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3

Non-applicable Icons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3

Copy Protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3

Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3

Express Media Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3

LCD Brightness and Eye Strain . . . . . . . . . . . . . . . . . . . . . . . . . 10-3

Appendix A Specifications

Appendix B Display Modes

Appendix C AC Power Cord and Connectors

Appendix D Express Media Player Supported Languages

Glossary

Satellite M100 xxvii

xxviii Satellite M100

Satellite M100

Preface

Congratulations on your purchase of the Satellite M100 computer. This
powerful notebook computer provides excellent expansion capability,
including multimedia devices, and it is designed to provide years of reliable,
high-performance computing.

This manual tells how to set up and begin using your Satellite M100
computer. It also provides detailed information on configuring your
computer, basic operations and care, using optional devices and
troubleshooting.

If you are a new user of computers or if you're new to portable computing,
first read over the Satellite M100 Features and The Grand Tour chapters to
familiarize yourself with the computer's features, components and
accessory devices. Then read Getting Started for step-by-step instructions
on setting up your computer.

If you are an experienced computer user, please continue reading the
preface to learn how this manual is organized, then become acquainted with
this manual by browsing through its pages. Be sure to look over the Special
features section of the Satellite M100 Features, to learn about features that
are unique to the computer.

User’s Manual xxix

Manual contents

This manual has ten chapters, three appendixes, a glossary and an index.
Chapter 1, Satellite M100 Features, is an overview of the computer's special

features, utilities, and options.
Chapter 2, The Grand Tour, identifies the components of the computer and

briefly explains how they function.
Chapter 3, Getting Started, provides a quick overview of how to begin

operating your computer and gives tips on safety and designing your work
area. Be sure to read the sections on setting up the operating system and
on restoring the preinstalled software.

Chapter 4, Operating Basics, includes instructions on using the following
devices: TouchPad, the optical disc drives, the internal modem, LAN and
wireless LAN. It also provides tips on care of the computer, disks and DVD/
CD-ROMs.

Chapter 5, The Keyboard, describes special keyboard functions including
the keypad overlay and hotkeys.

Chapter 6, Power and Power-Up Modes, gives details on the computer's
power resources.

Chapter 7, HW Setup, introduces you to the TOSHIBA Hardware Setup
program.

Chapter 8, Optional Devices, describes the optional hardware available.
Chapter 9, Troubleshooting, provides helpful information on how to perform

some diagnostic tests, and suggests courses of action if the computer
doesn't seem to be working properly.

Chapter 10, Disclaimers, provides disclaimer information related to your
computer.

The Appendices provide technical information about your computer.
The Glossary defines general computer terminology and includes a list of

acronyms used in the text.

Preface

xxx Satellite M100