Datasheet LTM08C351S Datasheet (TOSHIBA)

T oshiba Matsushita Display Technology Co., Ltd

PRODUCT INFORMATION

26cm COLOR TFT-LCD MODULE

(10.4 TYPE)

LTA104D183F

(p-Si TFT)

All information is subject to change without notice. Please read bottom notes.

FEATURES

(1) 10.4 SVGA color display with High Luminance
(2) Built in Long Life Lamps(MTTF:50,000 h)
( Condition/ Ta:25°C, I
(3) Replaceable structure of lamp units
(4) RoHS compliant
(5) Resistance type touch panel assemble(4 wire, Except controller)

:6.0mA(rms)(continuing lighting), fFL:40kHz )

FL

TENTATIVE

RoHS compatible

MECHANICAL SPECIFICATIONS

Item Specifications
Dimensional Outline (typ.) 242.0 (W) x 178.45 (H) x 15.4 (D) mm
Number of Pixels 800 (W) x 600 (H) pixels
Active Area 21 1.2 (W) x 158.4 (H) mm
Pixel Pitch 0.264 (W) x 0.264 (H)
Weight (approximately) (800) g
Backlight Sidelight (2 CCFLs)

ABSOLUTE MAXIMUM RATINGS

Item Min. Max. Unit

(VDD) -0.3 4.0 V Supply Voltage

(V

) 0 2.0 kV(rms)

FL

FL Driving Frequency (fFL) --- 100 KHz
Input Signal Voltage (VIN) -0.3 VDD+0.3 V
Operating Temperature
Storage Temperature -30 80 °C
Storage Humidity
(Max. wet bulb temperature = 39°C)

*1: Wet bulb temperature should be 39°C Max., and no condensation of water .

*1

-20 70 °C

10 90 %(RH)

ELECTRICAL SPECIFICATION (Ta=25°C) (RECOMMENDED OPERATION CONDITION)

Item Min. Typ. Max. Unit Remarks

(VDD) 3.0 3.3 3.6 V Supply Voltage

(V

) --- 470 --- V(rms)

FL

FL Start Voltage (V
Differential Input Voltage (VID) 100 --- 600 mV
Common Mode Input Voltage (VCM) 1.0 --- 2.4-(VID)/2 V

Power Consumption

*2: The surface temperature caused by self heat radiation of cell itself is specified on this item
*3: 8 color bars pattern *4: Except the efficiency of FL inverter

*1 *2

--- 6.3 --- W IFL =6.0mA(rms)

) 1200 --- 1900 V(rms) Ta=0°C

SFL

*3

(IDD)

--- 205 --- mA Current Consumption

*4

(I

)

3.0 6.0 6.5 mA(rms)

FL

OPTICAL SPECIFICATION (Ta=25°C)

Item Min. Typ. Max. Unit Remarks

Contrast Ratio (CR) 250 450 --- ---

(Upper+Lower) --- 100 --- ° Viewing Angle

(CR ≥ 10)

Luminance (L) 250 320 --- cd/m2 IFL=6.0mA(rms)
Lamp Life Time (MTBF)*5 *6 50,000 h

*5 : Conditions ;Ta=25°C, IFL=6.0mA(rms), continuous lighting
*6 : Definitions of failure ; 1) Lcd luminance becomes half of the minimum value. 2) Lamp doesn’t light normally.

*The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by
Toshiba Matsushita Display Technology or other rights of the third parties which may result from its use. No license is granted by
implication or otherwise under any patent or patent rights of Toshiba Matsushita Display Technology or others.

*The information contained herein may be changed without prior notice. It is therefore advisable to contact Toshiba Matsushita
Display Technology before proceeding with the design of equipment incorporating this product.

(Left+Right) --- 120 --- °

(tON) --- 8 --- ms Response Time

(t

) --- 17 --- ms

OFF

(1/12) 2007-10-18 (Ver.0.1R)

LTA104D183F

<Touch Panel Condition>

Recommended Operating Conditions

Item Min. Typ. Max. Unit Remarks
Supply Voltage VTP --- 5.0 7.0 V

Electrical Specifications

Item Min. Typ. Max. Unit Remarks
Insulation Resistance Z 20 --- --- MOhm DC25V
Resistance
between
Terminals
Linearity - 1.5 %
Chattering - 10 msec

#1 - #3(X) Rx 200 --- 1500 Ohm
#2 - #4(Y) Ry 100 --- 600 Ohm

Measured at connector
pin(including conductor
resistance).

Mechanical Specifications

Item Min. Typ. Max. Unit Remarks
Operating Starting Force 5 --- 50 gf
Surface Hardness 3 H

(2/12) 2007-10-18 (Ver.0.1R)

DIMENSIONAL OUTLINE

242

90+/-5

235

233.3+/-0.3

214.6(Bezel Opening)

211.2(LCD Active Area)

23.4+/-0.3

211.2(T/P Active Area)

223.3(T/P)

CN2

CN3

TENTATIVE

132.6+/-0.3

LTD104D183F

Unit : mm
Standard tolerance : 0.5

233.3+/-0.3

14.7+/-0.3

16.4

4.2+/-0.3

(122)

9.9

15.4

13.2+/-0.3

16.4

2.5+/-0.3

5.6+/-0.3

(88.3)

surface : Back side

FPC contacting

A

No.1

9.05

2.05

13.5+/-0.3

9.05

7.1+/-0.3

No.4

158.4(T/P Active Area)

172.4(T/P)

161.7+/-0.3

158.4(LCD Active Area)

162.4(Bezel Opening)

178.45+/-0.3

1+/-0.15
5+/-0.2

3+/-0.05

11

(5)

1+/-0.15

3

DETAIL A(2 : 1)

0.30+/-0.05

XR

YU

YD

PIN ASSIGNMENT

XL

1

2

3

4

(3/12) 2007-10-18 (Ver.0.1R)

DIMENSIONAL OUTLINE

TENTATIVE

(88.3) (T/P)

(70.1) (T/P)

LTA104D183F

Unit : mm
Standard tolerance : 0.5

(117.5)

(176.5)

CN1

(4/12) 2007-10-18 (Ver.0.1R)

(Mi

)

BLOCK DIAGRAM

DC/DC
Converter

CN1

Gray Scale
Manipulation
Voltage
Generation
Circuit

Panel
Controller

I/F Connector

SEQUENCE OF POWER SUPPLIES AND SIGNALS

s

m

5

.

0

s

m

0

1

.

n

)

.

x

a

M

(

Y-Driver IC

CCFL Backlight

CCFL Backlight

LCD Panel
800 x 600 pixels
With Touch Panel

X-Driver IC

)

.

n

i

M

(

s

m

1

.

0

s

m

0

0

1

)

.

x

a

M

(

m

0

0

5

LTA104D183F

CN3

Connector

Connector

CN2

CN4

.

n

i

M

(

s

)

DD

V

0.2V

CLK+/­RxIN0+/-

RxIN1+/­RxIN2+/-

0

2

5

m

s

(

M

FL Input Voltage

i

n

10%

3

.

0

V

s

m

0

4

.

)

V

SFL

M

(

)

.

x

0

a

m

s

(

M

i

n

.

)

3

s

e

c

0

4

0

(

10%

(

s

m

m

s

(

M

i

n

.

V

FL

3

.

0

V

.

x

a

M

)

M

i

n

.

)

)

0.2V

0

m

s

(

M

i

n

.

)

0.2V

V

H

V

CM

V

L

V

SFL

V

FL

(5/12) 2007-10-18 (Ver.0.1R)

TIMING CHART

<H-Sync/V-Sync+DE Mode>

Vsync

Hsync

tvde

tvfp

DE

599

600

Hsync

thw

thfp

DE

RGB Data

NCL

thds

1

<DE-Only Mode>

(1)Vertical Timing

2 3

LTA104D183F

tv

tvw

th

tvd

tvblnk

1

th

thde

4

800

tvde

2

t

1

t

2

K

L

N

C

t

3

E

D

B

G

R

(

2

)

C

N

E

D

B

G

R

a

t

a

d

1line

m

i

n

t

a

r

i

z

H

o

K

L

t

a

d

l

o

a

n

T

i

Y

,

1

3

2

4

Y

5

9

8

g

t

3

t

t

c

4

,

Y

Y

,

2

Y

3

,

,

Y

,

5

6

4

7

7

9

Y

,

7

Y

,

X

Y

7

t

3

6

0

0

9

9

5

,

Y

9

,

7

9

Y

9

,

8

Y

Y

0

,

8

0

(6/12) 2007-10-18 (Ver.0.1R)

LTA104D183F

TIMING SPECIFICA TION

1) 2) 3) 4) 5) 6) 7)

<H-Sync/V-Sync+DE Mode>

Item Symbol min. typ. Max. unit

Frame Period
Vertical blanking Term

V-sync Pulse Width
Vertical Front Porch
Vertical Data Sync Period
Vertical Display Term
Horizontal Period

H-sync Pulse Width
Horizontal Front Porch
Horizontal Data Sync Period
Horizontal Display Term
Clock Period

tv

tvblnk

tvw
tvfp
tvds
tvde

th

thw
thfp
thds

thde

tc

608

--­8 25 28
2 --- --­2 --- --­6 --- ---

600 600 600
850

26.4
8 --- --­8 --- ---

16 --- ---

800 800 800

25.0 27.8 --- ns

625

17.78

1024

28.44

628

17.86

1056

---

th

ms

th
th
th
th
th
tc

us

tc
tc
tc
tc

< DE-Only Mode>

Frame Period t1 608
Vertical Display Term t2 600 x t3 600 x t3 600 x t3 ---

One Line Scanning Time t3 850 x tc
Horizontal Display Term t4 800 x tc 800 x tc 800 x tc ---

Clock Period tc 25.0 27.78 --- ns

Item Symbol Min. Typ. Max. Unit

---

26.4

625 x t3

17.78

1024 x tc

28.44

628 x t3

17.86

1056 x tc

---

---

ms

---

us

Note 1) Refer to “Timing Chart” and LVDS(DS90C365*, DS90C385*) specifications by National Semiconductor Corp.
Note 2) If NCLK is fixed to "H" or "L" level for certain period while DE is supplied, the panel may be damaged.
Note 3) If DE is fixed to “H” or “L” level for certain period while NCLK is supplied, the panel displays black with some flicker.
Note 4) Please adjust LCD operating signal timing and FL driving frequency, to optimize the display quality.

There is a possibility that flicker is observed by the interference of LCD operating signal timing and FL driving

condition (especially driving frequency), even if the condition satisfies above timing specifications.
Note 5) Do not make tv, th and tvds fluctuate.
Note 6) In case of using the long frame period, the deterioration of display quality, noise etc. may be occurred.
Note 7) NCLK count of each Horizontal Scanning Time should be always the same.
V-Blanking period should be “n” X “Horizontal Scanning Time”. (n: integer)
Frame period should be always the same.

(7/12) 2007-10-18 (Ver.0.1R)

LTA104D183F

CONNECTOR PIN ASSIGNMENT FOR INTERFACE

CN1 INPUT SIGNAL
Connector : 20268-020E-12F / I-PEX CO., LTD.
Mating Connector : 20230-020B-F or 20230-T20-F or 20230-W20B-F / I-PEX CO., LTD.

DF19G-20S-1F(FPC), DF19G-20S-1C(Cable) / HIROSE ELECTRIC CO., LTD.

Terminal No. Symbol Function

1 VDD Power Supply : +3.3V
2 VDD Power Supply : +3.3V
3 VSS GND
4 VSS GND
5 RxIN0- Negative LVDS differential data input (R0-R5, G0)
6 RxIN0+ Positive LVDS differential data input (R0-R5, G0)
7 VSS GND
8 RxIN1- Negative LVDS differential data input (G1-G5, B0-B1)
9 RxIN1+ Positive LVDS differential data input (G1-G5, B0-B1)

10 VSS GND

11 RxIN2- Negative LVDS differential data input (B2-B5, HS, VS, DE)
12 RxIN2+ Positive LVDS differential data input (B2-B5, HS, VS, DE)
13 VSS GND
14 CLK- Clock Signal(-)
15 CLK+ Clock Signal(+)
16 VSS GND
17 U/D Vertical Reverse(“L” level or Open : Normal, “H” level : Reverse)
18 L/R Horizontal Reverse(“L” level or Open : Normal, “H” level : Reverse)
19 NC
20 VSS GND

Note 1) Please connect GND pin to ground. Don’t use it as no-connect nor connection with high impedance.
Note 2) NC terminal should be open.

CN2,3 CCFL POWER SOURCE
Connector : BHR-03VS-1 / JAPAN SOLDERLESS TERMINAL MFG CO., LTD.
Mating Connector

Terminal No. Symbol Function

1 VFLH CCFL Power Supply ( high voltage)
2 NC
3 VFLL CCFL Power Supply (low voltage)

Note 3) Take away terminal No.2 of the mating connector. If does not take away, it may cause smoke burn of
electrical parts by high voltage.

CN4 TOUCH PANEL

FPC: 1.0mm pitch, Gold plating
Mating connector: FC1S004HA1 / JAE

Terminal No. Symbol Function

1 XR Touch Panel XR Terminal
2 YU Touch Panel YU Terminal
3 XL Touch Panel XL Terminal
4 YD Touch Panel YD Terminal

2)

Non Connectio n (open)

3)

: SM02(8.0)B-BHS-1 / JAPAN SOLDERLESS TERMINAL MFG CO., LTD.

2)

Non Connection (open)

(8/12) 2007-10-18 (Ver.0.1R)

RECOMMENDED TRANSMITTER (DS90C365* by National Semiconductor Corp.)
TO LTA104D183F INTERFACE ASSIGNMENT

Case1: 6bit Transmitter

DS90C365*

Input Terminal No. Input Signal

(Graphics controller output signal)

Symbol Terminal Symbol Function
TIN0 44 R0 Red Pixels Display Data (LSB)

TIN1 45 R1 Red Pixels Display Data
TIN2 47 R2 Red Pixels Display Data
TIN3 48 R3 Red Pixels Display Data
TIN4 1 R4 Red Pixels Display Data
TIN5 3 R5 Red Pixels Display Data (MSB)
TIN6 4 G0 Green Pixels Display Data (LSB)
TIN7 6 G1 Green Pixels Display Data
TIN8 7 G2 Green Pixels Display Data
TIN9 9 G3 Green Pixels Display Data
TIN10 10 G4 Green Pixels Display Data
TIN11 12 G5 Green Pixels Display Data (MSB)
TIN12 13 B0 Blue Pixels Display Data (LSB)
TIN13 15 B1 Blue Pixels Display Data
TIN14 16 B2 Blue Pixels Display Data
TIN15 18 B3 Blue Pixels Display Data
TIN16 19 B4 Blue Pixels Display Data
TIN17 20 B5 Blue Pixels Display Data (MSB)
TIN18 22 HSYNC H-Sync
TIN19 23 VSYNC V-Sync
TIN20 25 DE Compound Synchronization Signal
CLK IN 26 CLK Data Sampling Clock TCLK OUT-

Note 1) Please connect NC pin to nothing. Don't connect it to ground nor to other signal input.

Output

Signal

Symbol

TOUT0­TOUT0+

TOUT1­TOUT1+

TOUT2­TOUT2+

TCLK OUT+

LTA104D183F

LTA104D183F

Interface

(CN1)

Terminal Symbol

No.5
No.6

No.8
No.9

No.11
No.12

No.14
No.15

RxIN0­RxIN0+

RxIN1­RxIN1+

RxIN2­RxIN2+

CLK­CLK+

Rx IN0

Rx IN1

Rx IN2

TIN6 TIN5

G0

TIN13 TIN12 TIN11 TIN10 TIN9 TIN8

B1

TIN20

DE

R5

B0

T IN19 T IN18 T IN17 T IN16 T IN15

VSYNC

TIN4 TIN3 TIN2 TIN1 TIN0

R4

G5

HSYNC

R3 R2 R1 R0

G4

B5

G3

B4

G2

TIN7

G1

TIN14

B2B3

(9/12) 2007-10-18 (Ver.0.1R)

RECOMMENDED TRANSMITTER (DS90C385* by National Semiconductor Corp.)
TO LTA104D183F INTERFACE ASSIGNMENT

Case2: 8bit Transmitter

DS90C385*

Input Terminal No. Input Signal

(Graphics controller output signal)

Symbol Terminal Symbol Function
TIN0 51 R0 Red Pixels Display Data (LSB)

TIN1 52 R1 Red Pixels Display Data
TIN2 54 R2 Red Pixels Display Data
TIN3 55 R3 Red Pixels Display Data
TIN4 56 R4 Red Pixels Display Data
TIN6 3 R5 Red Pixels Display Data (MSB)
TIN7 4 G0 Green Pixels Display Data(LSB)
TIN8 6 G1 Green Pixels Display Data
TIN9 7 G2 Green Pixels Display Data
TIN12 11 G3 Green Pixels Display Data
TIN13 12 G4 Green Pixels Display Data
TIN14 14 G5 Green Pixels Display Data(MSB)
TIN15 15 B0 Blue Pixels Display Data (LSB)
TIN18 19 B1 Blue Pixels Display Data
TIN19 20 B2 Blue Pixels Display Data
TIN20 22 B3 Blue Pixels Display Data
TIN21 23 B4 Blue Pixels Display Data
TIN22 24 B5 Blue Pixels Display Data (MSB)
TIN24 27 HSYNC H-Sync
TIN25 28 VSYNC V-Sync
TIN26 30 DE Compound Synchronization Signal
TIN27 50 NC Non Connection (ope n)
TIN5 2 NC Non Connection (open)
TIN10 8 NC Non Connection (open)
TIN11 10 NC Non Connection (open)
TIN16 16 NC Non Connection (ope n)
TIN17 18 NC Non Connection (ope n)
TIN23 25 NC Non Connection (ope n)
CLK IN 31 CLK Data Sampling Clock TCLK OUT-

Note 1) Please connect NC pin to nothing. Don't connect it to ground nor to other signal input.

Output

Signal

Symbol

TOUT0­TOUT0+

TOUT1­TOUT1+

TOUT2­TOUT2+

TOUT3­TOUT3+

TCLK OUT+

LTA104D183F

LTA104D183F

Interface

(CN1)

Terminal Symbol

No.5
No.6

No.8
No.9

No.11
No.12

No.14
No.15

RxIN0­RxIN0+

RxIN1­RxIN1+

RxIN2­RxIN2+

CLK­CLK+

Rx IN0

Rx IN1

Rx IN2

Rx IN3

TIN7 TIN6 TIN4 TIN3 TIN2 TIN1 TIN0

G0

TIN18TIN15TIN14TIN13 TIN12TIN9

B1

TIN26

DE

TIN23TIN17TIN16TIN11TIN10TIN5 TIN27

NC

R5

B0

TIN25 TIN24

NC

R4

G5

HSYNCVSYNC

NC

R3 R2 R1 R0

G4

TIN22 TIN21 TIN20

B5

NC

G3

B4

NC

G2

TIN19

NC

TIN8

G1

B2B3

NC

(10/12) 2007-10-18 (Ver.0.1R)

256k (k=1024) COLORS COMBINATION TABLE

Display

Basic
Color

Gray

Scale of

Red

Gray

Scale of

Green

Gray

Scale of

Blue

Gray

Scale of

White &

Black

Black

Blue

Green

Light Blue

Red
Purple
Yellow

White

Black

Dark

↑
↓

Light

Red

Black

Dark

↑
↓

Light

Green

Black

Dark

↑
↓

Light

Blue

Black

Dark

↑
↓

Light

White

R5 R4 R3 R2 R1 R0

L L L L L L

L L L L L L

L L L L L L

L L L L L L

H H H H H H

H H H H H H

H H H H H H

H H H H H H H H H H H H H H H H H H

L L L L L L

L L L L L H L L L L L L L L L L L L L 1

L L L L H L L L L L L L L L L L L L L 2

:

:

H H H H L H L L L L L L L L L L L L L 6 1

H H H H H L L L L L L L L L L L L L L 6 2

H H H H H H L L L L L L L L L L L L R e d L 63

L L L L L L

L L L L L L L L L L L H

L L L L L L L L L L H L L L L L L L L 2

:

:

L L L L L L H H H H L H L L L L L L L 6 1

L L L L L L

L L L L L L

L L L L L L

L L L L L L L L L L L L L L L L L H L 1

L L L L L L L L L L L L L L L L H L L 2

:

:

L L L L L L L L L L L L H H H H L H L 6 1

L L L L L L

L L L L L L

L L L L L L

L L L L L H L L L L L H L L L L L H L 1

L L L L H L L L L L H L L L L L H L L 2

:

:

H H H H L H H H H H L H H H H H L H L 6 1

H H H H H L

H H H H H H

G5 G4 G3 G2 G1 G0

L L L L L L L L L L L L

L L L L L L H H H H H H

H H H H H H L L L L L L

H H H H H H H H H H H H

L L L L L L L L L L L L

L L L L L L H H H H H H

H H H H H H L L L L L L

L L L L L L L L L L L L L 0

L L L L L L L L L L L L L 0

H H H H H L L L L L L L L 6 2

H H H H H H L L L L L L Green L63

L L L L L L L L L L L L L 0

L L L L L L H H H H H L L 6 2

L L L L L L H H H H H H Blue L63

L L L L L L L L L L L L L 0

H H H H H L H H H H H L L 6 2

H H H H H H H H H H H H White L63

:

:

:

:

:

:

:

:

LTA104D183F

B5 B4 B3 B2 B1 B0

:

:

L L L L L L L 1

:

:

:

:

:

:

Gray Scale

Level

---

---

---

---

---

---

---

---

L 3 …

L 6 0

L 3 …

L 6 0

L 3 …

L 6 0

L 3 …

L 6 0

(11/12) 2007-10-18 (Ver.0.1R)

LTA104D183F

!

FOR SAFETY

LCD module is generally designed with precise part s to achieve light weighted thin mechanical dimensions.
In using our Modules, make certain that you fully understand and put into practice the warnings and safety precautions
detailed in Engineering Information No.EE-N001,"CAUTIONS AND INSTRUCTIONS FOR TOSHIBA LCD MODULES".
Refer to individual specifications and TECHNICAL DATA sheets (hereinafter called "TD") for more detailed technical
information.

1) SPECIAL PURPOSES

A) Toshiba Matsushita Display Technology's Standard LCD Modules have not been customized for operation in extreme
environments or for use in applications where performance failures could be life-threatening or otherwise catastrophic.

B) Since Toshiba Matsushita Display Technology's Standard LCD Modules have not been designed for operation in extreme
environments, they must never be used in devices that will be exposed to abnormally high levels of vibration or shock which
exceed Toshiba Matsushita Display Technology's published specification limits.

C) In addition, since Toshiba Matsushita Display Technology Standard LCD Modules have not been designed for use in
applications where performance failures could be life-threatening or catastrophic, they must never be installed in aircraft
navigation control systems (such as, but not limited to Traffic Collision Avoidance System and Air Traffic Indicator), in military
defense or weapons systems, in critical industrial process-control systems (e.g., those involved in the production of nuclear
energy), or in critical medical device or patient life-support systems.

2) DISASSEMBLING OR MODIFICATION

DO NOT DISASSEMBLE OR MODIFY the module. It may damage sensitive parts inside LCD module, and may cause
scratches or dust on the display.
Toshiba Matsushita Display Technology doses not warrant the module, if customer disassembled or modified it.

3) BREAKAGE OF LCD PANEL

DO NOT INGEST liquid crystal material, DO NOT INHALE this material, and DO NOT CONTACT the material with skin, if
LCD panel is broken and liquid crystal material spills out.
If liquid crystal material comes into mouth or eyes, rinse mouth or eyes out with water immediately.
If this material contact with skin or cloths, wash it off immediately with alcohol and rinse thoroughly with water.

4) GLASS OF LCD PANEL

BE CAREFUL WITH CHIPS OF GLASS that may cause injuring fingers or skin, when the glass is broken.

5) ELECTRIC SHOCK

DISCONNECT POWER SUPPLY before handling LCD module.
DO NOT TOUCH the parts inside LCD module and the fluorescent lamp's connector or cables in order to prevent electric
shock, because high voltage is supplied to these parts from the inverter unit while power supply is turned on.

6) ABSOLUTE MAXIMUM RATINGS AND POWER PROTECTION CIRCUIT

DO NOT EXCEED the absolute maximum rating values under the worst probable conditions caused by the supply voltage
variation, input voltage variation, variation in parts' constants, environmental temperature, etc., otherwise LCD module may
be damaged.
Employ protection circuit for power supply, whenever the specification or TD specifies it.
Suitable protection circuit should be applied for each system design.

7) RECOMMENDED OPERATION CONDITIONS

The performance and quality of the LCD panel are warranted only when the LCD panel is used within “the recommended
operation conditions”. Toshiba Matsushita Display Technology Co., Ltd. never warrants the performance and quality of the
LCD panel when you use the LCD panel over “the recommended operation conditions”, although within “the absolute
maximum rating”.
To use the LCD panel over “the recommended operation conditions” may have bad influence on the characteristics and
reliability of the LCD panel and may shorten the life of the LCD panel.
Therefore, when designing the whole set, not to be over “the recommended operation conditions”, you should fully take care
of supply voltage change, characteristic of connection parts, serge of input-and-output line, and surround ing temperature.

8) DISPOSAL

When dispose LCD module, obey to the applicable environmental regulations.

(12/12) 2007-10-18 (Ver.0.1R)