Toshiba G00E034 Service Note

BSINo. G00E034 Page 1
BSI No.: G00E034 Publish
2000/07/05
Date: Subject: ROM Version Improvement (Ver.170)<Correction: July. 5, 2000>
Model: FC22
Category Field Application UNIT
Request from the field, Change
of Parts
FactoryApplication: From May 2000
To be applied when necessary Software
CONTENT
The ROMs have been improved as follows.
ROM
SYS-ROM PMA-T310Sxx-ZZZ 160 170 T310Sxx170 (08-900)
References)
ROM
M-ROM PRA-T310M-13 T310M-13 (08-902) IMC-ROM PRA-T310IMC-13 T310IMC-13 (08-903) SCM-ROM PRA-T310SCM-11 T310SCM-11 (08-904) AI-ROM PRA-T511MAC-07 T511MAC-07 (08-905)
[Changed/Added Part No.]
MODEL P-I Before Change After Change Note P I R
P-I: Page-Item P: Contents of Change I: Interchangeability R: Reasons for Change
Name Before
Name New Version
8-12 A
8-12 B
8-12 C
4406574280 PMA-T310SUC-160 4406574290 PMA-T310SEU-160 4406574300 PMA-T310SX-160
Change
4406574370 PMA-T310SUC-170 4406574380 PMA-T310SEU-170 4406574390 PMA-T310SX-170
After Change
New Version
NAD
MJD
ASD,AUD
,
TWD
SAD
FAA
C B B Y
C B B Y
C B B Y
[Notes]
Be sure to carry out simultaneous exchange for SIC-ROM, M-ROM and IMC-ROM.1.
2.
When Ver.160 of SYS-ROM/Ver.13 of M-ROM/IMC-ROM is changed, be sure to perform
after ROMs change]
[Work after ROMs change]
Carry out the following procedure after changing ROMs.
.
[Work
BSINo. G00E034 Page 2
1. Initialization of image parameters *Note1 (1) [1] +[3]+[POWER] : While pressing keys [1] and [3] simultaneously, turn on the main switch. (2) Wait about 20 seconds. The main switch is turned off when the following messages appear on the LCD.
"Initialized image parameters. Please turn off and on the copier. Thank you."
2. Initialization of image quality control Please refer to "3. Image Quality Control Adjustment" on the "26 ADJUSTMENT" page of the unpacking instructions for the FC22. (1) [0] +[5]+[POWER] (2) Key in code "879" and press the START key. Wait about 3 minutes.
3. Automatic Calibration of Gradation Please refer to "4. Automatic Calibration of Gradation" on the "26 ADJUSTMENT" page of the Unpacking Instructions for the FC22. (1) Select the cassette of A3 (or LD) sized paper. (2) [For TEXT and MAP modes]
a. Key in code "4", then press the SETTING key. The test chart is output. b. Set the test chart on the original glass. c. Key in code "643" and press the START key. Wait a few seconds. d. Press the "2" key, the START key and INTERRUPT key in that order. e. After the message "SCAN COMPLETED" appears, press the START key. f. After the message "COMPLETED" appears, press the STOP key.
(3) [For PHOTO made]
a. Key in code "5", then press the SETTING key. The test chart is output. b. Set the test chart on the original glass. c. Key in code "643" and press the START key. Wait a few seconds. d. Press "3" key, the START key and INTERRUPT key in that order. e. After the message "SCAN COMPLETED" appears, press the START key. f. After the message "COMPLETED" appears, press the STOP key.
4. Turn off the main switch.
*Note1 Initialization of image parameters
When initialization of the image parameters is performed, the following adjustment value will be changed to the initial value. Please readjust if needed. Please refer to page 1-73 from page 1-69 in the Service Handbook. 1-8. Density Adjustment (08/550-589) 1-9. Color Balance Adjustment (08/779-798) 1-10. Offset Amount for Processing Background (08/698/717) 1-11. Judgment Threshold for ACS (08/675) 1-12. AI Mode Setting (08/678, 682) 1-13. Sharpness Adjustment (08/730-745)
[Changed Contents]
SYS-ROM
[160 --> 170]
In order to increase the quality of the reproducibility of the color of the photo mode, the image 1. processing parameters for the color changing table has been changed. (The color reproduction of light red has been improved.) When code "201" of the setting code "08" is set to 1 and "361" is set to 1, LT size may be detected 2. as A4 size. This has been corrected. In case the setting number of "mode memory" is greater than the setting number of "MAX9 3. (08-300)", when a copy is made in "mode memory", the display shows "Serviceman call". This has been corrected. To match the ROM label display and setting mode (08) display, the ROM version display types 4.
BSINo. G00E034 Page 3
have been changed (see below).
Setting Mode (08)
Code
902 903 904
Each version display of 08-905/907~909/914~916 has been opened. 5.
Setting Mode (08)
Code
905 907 908 909 914 915
916 The printing job from the bypass feed can be started immediately after copy job finished.6. The density failure occurs in case of some background value combination for 05/698-717 setting 7. and control panel setting. A HELP message for thick originals has been added.8. The setting at the factory in Fiery scanning has been corrected to the non-filter mode.9.
Setting Item Before Change After Change Engine ROM version (LGC) Engine ROM version (IMC) Scan ROM version
Setting Item Default Acceptable
AI ROM version First language UI data Second language UI data Third languages UI data Fix UI data Common UI data System firm
T310MXXXX T310IMCXXXX T310SCMXXXX
value
-
-
-
-
-
-
-
T310M-XX T310IMC-XX T310SCM-XX
Content Operation
-
-
-
-
-
-
-
T511MAC-XX V002.023 3 V002.023 6 V002.023 11 V002.004 0 V002.001 0 V052.000 SJP
procedure
group
2 2 2 2 2 2 2
Though an image in the non-filter mode can be produced faithful to the original, if the filter mode is set for the image, it can be made even clearer. The following code has been newly added and can be exchanged at the user's request.
Setting Mode (08)
Code
507 Filter setting selection
Table of History of ROM Version Combination
Setting Item Default Acceptable
value
0 0~1 0: non-filter mode (OFF)
in Fiery scanning
Time of Application
1st lot 130 10 10 10 06 2000/1 140 11 11 11 07 2000/2 150 12 12 2000/3 160 13 13 2000/5 170
SYS ROMMROM
IMC ROM
Content Operation
1: filter mode (ON)
SCM
BSI No
ROMAIROM
--­G00B931
G00C964 G00E034
procedure Group
1
--------------------------------------------------------------------------------------------------­July 5, 2000 Change: printed image mode --> photo
Attached File
photo mode
photophoto
Related Documents:
LinkTo: Link From:
BSINo. G00E034 Page 4
Loading...