Toshiba f60 User Manual

User’s Manual

Qosmio F60 Series

Table of Contents

Table of Contents

Copyright. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi

Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi

Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

Macrovision License . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

FCC information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii

EU Conformity Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

VCCI Class B Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

Canadian regulatory information (Canada only) . . . . . . . . . . . . . . . . . ix

Important Safety Information for Computers with TV tuner . . . . . . . . . x

Following information is only for EU-member states: . . . . . . . . . . . . . x

Disposing of the computer and the computer’s batteries . . . . . . . . . xi

Optical disc drive safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . xi

International precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiv

Preface

Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xvi

General Precautions

Provide adequate ventilation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xix

Creating a computer-friendly environment . . . . . . . . . . . . . . . . . . . . . xx

Stress injury . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xx

Heat injury . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xx

Pressure or impact damage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxi

Mobile phones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxi

Instruction Manual for Safety and Comfort . . . . . . . . . . . . . . . . . . . . xxi

The cautions on use of a Qosmio F60 Series computer. . . . . . . . . . xxii

Chapter 1 Getting Started

Equipment checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

System Recovery Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12

System Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13

User’s Manual ii

Chapter 2 The Grand Tour

Front with the display closed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Left side. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Right side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Back . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Underside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

Front with the display open. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10

Optical disc drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12

AC adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16

Chapter 3 Hardware, Utilities and Options

Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Special features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11

TOSHIBA Value Added Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14

Utilities and Applications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15

Optional devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19

Bridge media slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20

Optional accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-36

Chapter 4 Operating Basics

Using the Touch Pad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

AV Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

Web Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

Using the TOSHIBA Face Recognition . . . . . . . . . . . . . . . . . . . . . . . . 4-4

Using optical disc drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7

Writing CD/DVD/BDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11

TOSHIBA DVD PLAYER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-22

Using WinDVD BD for TOSHIBA . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25

Media care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-27

TV Tuner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-29

Sound system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-30

Wireless communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-33

LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-35

Computer Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-37

Using the Hard Disk Drive (HDD) Protection . . . . . . . . . . . . . . . . . . 4-39

Using the TOSHIBA USB Sleep and Charge Utility . . . . . . . . . . . . . 4-41

Heat dispersal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-43

Chapter 5 The Keyboard

Typewriter keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Function keys: F1 … F9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

Soft keys: FN key combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

Hot keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

Windows special keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4

Desktop-style Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5

Generating ASCII characters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5

Qosmio F60 Series

User’s Manual iii

Chapter 6 Power and Power-Up Modes

Power conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

Monitoring of power condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2

Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3

Replacing the battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8

TOSHIBA Password Utility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10

Starting the computer by password . . . . . . . . . . . . . . . . . . . . . . . . . 6-12

Power-up modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12

Panel power on/off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13

System automatic Sleep/Hibernation . . . . . . . . . . . . . . . . . . . . . . . . 6-13

Chapter 7 HW Setup

Accessing HW Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

HW Setup window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

Chapter 8 AV functions

Media Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

Front operation panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2

TOSHIBA Button Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3

Remote controller. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6

Using the remote controller. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-11

Installing/Removing batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12

QosmioEngine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-14

Chapter 9 Troubleshooting

Problem solving process. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1

Hardware and system checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3

TOSHIBA support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-24

Appendix A Specifications

Physical Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Appendix B Display Controller and Video mode

Display controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1

Video mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1

Appendix C Wireless LAN

Card Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1

Radio Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2

Supported Frequency Sub-bands. . . . . . . . . . . . . . . . . . . . . . . . . . . . C-3

Appendix D Bluetooth wireless technology Interoperability

Bluetooth wireless technology and your Health . . . . . . . . . . . . . . . . D-2

Regulatory statements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-2

Using Bluetooth Adaptor from TOSHIBA equipment in Japan . . . . D-4

Appendix E AC Power Cord and Connectors

Certification agencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-1

Appendix F TOSHIBA Anti-theft Protection Timer

Qosmio F60 Series

User’s Manual iv

Appendix G TOSHIBA PC Health Monitor

Starting the TOSHIBA PC Health Monitor. . . . . . . . . . . . . . . . . . . . . . G-2

Cleaning the cooling module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G-3

Appendix H Legal Footnotes

Non-applicable Icons*1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H-1

CPU*2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H-1

Memory (Main System)*3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H-2

Battery Life*4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H-3

Hard Disk Drive (HDD) Capacity*5 . . . . . . . . . . . . . . . . . . . . . . . . . . . H-3

LCD*6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H-3

Graphics Processor Unit ("GPU”)*7 . . . . . . . . . . . . . . . . . . . . . . . . . . H-3

Wireless LAN*8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H-4

Copy Protection*9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H-4

TV Tuner*10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H-4

Images*11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H-4

LCD Brightness and Eye Stain*12. . . . . . . . . . . . . . . . . . . . . . . . . . . . H-4

Safety Use for TV Tuner*13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H-4

Glossary

Index

Qosmio F60 Series

User’s Manual v

Copyright

Disclaimer

Qosmio F60 Series

© 2009 by TOSHIBA Corporation. All rights reserved. Under the copyright
laws, this manual cannot be reproduced in any form without the prior
written permission of TOSHIBA. No patent liability is assumed, with respect
to the use of the information contained herein.

TOSHIBA Qosmio F60 Series Portable Personal Computer User’s Manual

First edition November 2009
Copyright authority for music, movies, computer programs, databases and

other intellectual property covered by copyright laws belongs to the author
or to the copyright owner. Copyrighted material can be reproduced only for
personal use or use within the home. Any other use beyond that stipulated
above (including conversion to digital format, alteration, transfer of copied
material and distribution on a network) without the permission of the
copyright owner is a violation of copyright or author's rights and is subject to
civil damages or criminal action. Please comply with copyright laws in
making any reproduction from this manual.

Please note that you may infringe the owner's rights protected by the
copyright laws if you use the screen mode switching functions (e.g. Wide
mode, Wide Zoom mode, etc.) of this product to display enlarged
images/video at coffee shops or hotels for the purposes of profits or
providing these to the public.

This manual has been validated and reviewed for accuracy. The
instructions and descriptions it contains are accurate for the TOSHIBA
Qosmio F60 Series Portable Personal Computer at the time of this
manual’s production. However, succeeding computers and manuals are
subject to change without notice. TOSHIBA assumes no liability for
damages incurred directly or indirectly from errors, omissions or
discrepancies between the computer and the manual.

User’s Manual vi

Trademarks

IBM is a registered trademark and IBM PC is a trademark of International
Business Machines Corporation.

Intel, Intel SpeedStep, Intel Core, Celeron and Centrino are trademarks or
registered trademarks of Intel Corporation.

Windows, Microsoft and Windows logo are registered trademarks of
Microsoft Corporation.

Photo CD is a trademark of Eastman Kodak Company.
Bluetooth is a trademark owned by its proprietor and used by TOSHIBA

under license.
Memory Stick, Memory Stick Duo, Memory Stick PRO and Memory Stick

PRO Duo are trademarks or registered trademarks of Sony Corporation.
WinDVD is a trademark of the Corel Corporations.
DVD MovieFactory is a trademark of the Corel Corporations.
Labelflash is a trademark of YAMAHA CORPORATION.
Manufactured under license from Dolby Laboratories.

Dolby and the double-D symbol are trademarks of Dolby Laboratories.
Dolby Home Theater is a trademark of Dolby Laboratories.

PalmCheck and TouchPad are trademarks of Synaptics Incorporated.
ConfigFree is a trademark of Toshiba Corporation.
Wi-Fi is a registered trademark of the Wi-Fi Alliance.
Secure Digital and SD are trademarks of SD Card Association.
MultiMediaCard and MMC are trademarks of MultiMediaCard Association.
xD-Picture Card is a trademark of FUJIFILM Corporation.
Other trademarks and registered trademarks not listed above may be used

in this manual.

Qosmio F60 Series

Macrovision License

This product includes copyright protection technology and intellectual
property that are patented in the U.S. and other countries. These patents
are the property of Macrovision Corporation. The use of copyright
protection must be authorized by Macrovision Corporation. It is intended for
home and other restricted-use applications, unless Macrovision
Corporation expressly authorizes otherwise. All forms of reverse
engineering or decompiling are forbidden.

User’s Manual vii

FCC information

FCC notice "Declaration of Conformity Information"

This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

■ Reorient or relocate the receiving antenna.

■ Increase the separation between the equipment and receiver.

■ Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

■ Consult the dealer or an experienced radio/TV technician for help.

Only peripherals complying with the FCC class B limits may be attached to
this equipment. Operation with non-compliant peripherals or peripherals
not recommended by TOSHIBA is likely to result in interference to radio
and TV reception. Shielded cables must be used between the external
devices and the computer’s external monitor port, Universal Serial Bus
(USB 2.0) ports, eSATA/USB combo port, HDMI out port and microphone
jack. Changes or modifications made to this equipment, not expressly
approved by TOSHIBA or parties authorized by TOSHIBA could void the
user’s authority to operate the equipment.

Qosmio F60 Series

FCC conditions

This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including
interference that may cause undesired operation.

Contact

Address: TOSHIBA America Information Systems, Inc.

9740 Irvine Boulevard
Irvine, California 92618-1697

Telephone: [phone]

User’s Manual viii

EU Conformity Statement

This product and - if applicable - the supplied accessories too are marked
with "CE" and comply therefore with the applicable harmonized European
standards listed under the Low Voltage Directive 2006/95/EC, the EMC
Directive 2004/108/EC and/or R&TTE Directive 1999/5/EC.

Responsible for CE­marking:

Manufacturer: Toshiba Corporation, 1-1 Shibaura 1-chome,

The complete official EU CE Declaration can be obtained on following
internet page:

http://epps.toshiba-teg.com/

VCCI Class B Information

Qosmio F60 Series

TOSHIBA EUROPE GMBH, Hammfelddamm 8,
41460 Neuss, Germany.

Minato-ku, Tokyo, 105-8001, Japan

Canadian regulatory information (Canada only)

This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus as set out in the Radio Interference
Regulation of the Canadian Department of Communications.

Note that Canadian Department of Communications (DOC) regulations
provide, that changes or modifications not expressly approved by
TOSHIBA Corporation could void your authority to operate this equipment.

This Class B digital apparatus meets all requirements of the Canadian
Interference-Causng Equipment Regulations.

Cet appareil numérique de la class B respecte toutes les exgences du
Règlement sur le matériel brouileur du Canada.

User’s Manual ix

Qosmio F60 Series

Pb, Hg, Cd

Important Safety Information for Computers with TV tuner

IEC60950-1/EN60950-1 Information technology equipment - Safety ­Coaxial cable connection to this computer must only be used if the cable
outer conductive shielding has been grounded by the cable installer at the
building premises as close to the point of cable entrance, or attachment, as
practicable and the connection complies with all local cable installation
requirements that are applicable in your area.

Following information is only for EU-member states:

Disposal of products

The crossed out wheeled dust bin symbol indicates that products must be
collected and disposed of separately from household waste. Integrated
batteries and accumulators can be disposed of with the product. They will
be separated at the recycling centres.

The black bar indicates that the product was placed on the market after
August 13, 2005.

By participating in separate collection of products and batteries, you will
help to assure the proper disposal of products and batteries and thus help
to prevent potential negative consequences for the environment and human
health.

For more detailed information about the collection and recycling
programmes available in your country, please visit our website
(http://eu.computers.toshiba-europe.com) or contact your local city office or
the shop where you purchased the product.

Disposal of batteries and/or accumulators

The crossed out wheeled dust bin symbol indicates that batteries and/or
accumulators must be collected and disposed of separately from household
waste.

If the battery or accumulator contains more than the specified values of lead
(Pb), mercury (Hg), and/or cadmium (Cd) defined in the Battery Directive
(2006/66/EC), then the chemical symbols for lead (Pb), mercury (Hg) and/or
cadmium (Cd) will appear below the crossed out wheeled dust bin symbol.

By participating in separate collection of batteries, you will help to assure
the proper disposal of products and batteries and thus help to prevent
potential negative consequences for the environment and human health.

For more detailed information about the collection and recycling
programmes available in your country, please visit our website
(http://eu.computers.toshiba-europe.com) or contact your local city office or
the shop where you purchased the product.

These symbols may not stick depending on the country and region where
you purchased.

User’s Manual x

Qosmio F60 Series

Disposing of the computer and the computer’s batteries

■ Discard this computer in accordance with applicable laws and

regulations. For further information, contact your local government.

■ This computer contains rechargeable batteries. After repeated use, the

batteries will finally lose their ability to hold a charge and you will need
to replace them. Under certain applicable laws and regulation, it may be
illegal to dispose of old batteries by placing them in the trash.

■ Please be kind to our shared environment. Check with your local

government authority for details regarding where to recycle old batteries
or how to dispose of them properly. This product contains mercury.
Disposal of this material may be regulated due to environmental
considerations. For disposal, reuse or recycling information, please
contact your local government.

Optical disc drive safety instructions

Be sure to check the international precautions at the end of this section.

Panasonic Communications

DVD Super Multi UJ890AD/UJ890ED with Labelflash

■ The DVD Super Multi drive model employs a laser system. To ensure

proper use of this product, please read this instruction manual carefully
and retain for future reference. Should the unit ever require
maintenance, contact an authorized service location.

■ Use of controls, adjustments or the performance of procedures other

than those specified may result in hazardous radiation exposure.

■ To prevent direct exposure to the laser beam, do not try to open the

enclosure.

User’s Manual xi

TM

BD ROM UJ141/BD-RE UJ240

Qosmio F60 Series

■ The BD-R/RE drive model employs a laser system. To ensure proper

use of this product, please read this instruction manual carefully and
retain for future reference. Should the unit ever require maintenance,
contact an authorized service location.

■ Use of controls, adjustments or the performance of procedures other

than those specified may result in hazardous radiation exposure.

■ To prevent direct exposure to the laser beam, do not try to open the

enclosure.

User’s Manual xii

Qosmio F60 Series

User’s Manual xiii

International precautions

Qosmio F60 Series

CAUTION: This appliance contains a
laser system and is classified as a
“CLASS 1 LASER PRODUCT.” To use
this model properly, read the instruction
manual carefully and keep this manual
for your future reference. In case of any
trouble with this model, please contact
your nearest “AUTHORIZED service
station.” To prevent direct exposure to the
laser beam, do not try to open the
enclosure.

VORSICHT: Dieses Gerät enthält ein
Laser-System und ist als
“LASERSCHUTZKLASSE 1 PRODUKT”
klassifiziert. Für den richtigen Gebrauch
dieses Modells lesen Sie bitte die
Bedienungsanleitung sorgfältig durch
und bewahren diese bitte als Referenz
auf. Falls Probleme mit diesem Modell
auftreten, benachrichtigen Sie bitte die
nächste “autorisierte Service-Vertretung”.
Um einen direkten Kontakt mit dem
Laserstrahl zu vermeiden darf das Gerät
nicht geöffnet werden.

ADVARSEL: Denne mærking er anbragt
udvendigt på apparatet og indikerer, at
apparatet arbejder med laserstråler af
klasse 1, hviket betyder, at der anvendes
laserstrlier af svageste klasse, og at man
ikke på apparatets yderside kan bilve
udsat for utilladellg kraftig stråling.

APPARATET BOR KUN ÅBNES AF
FAGFOLK MED SÆRLIGT KENDSKAB
TIL APPARATER MED
LASERSTRÅLER!

Indvendigt i apparatet er anbragt den her
gengivne advarselsmækning, som
advarer imod at foretage sådanne
indgreb i apparatet, at man kan komme til
at udsatte sig for laserstråling.

User’s Manual xiv

Qosmio F60 Series

OBS! Apparaten innehåller
laserkomponent som avger laserstråining
överstigande gränsen för laserklass 1.

VAROITUS. Suojakoteloa si saa avata.
Laite sisältää laserdiodin, joka lähetää
näkymätöntä silmilie vaarallista
lasersäteilyä.

CAUTION: USE OF CONTROLS OR
ADJUSTMENTS OR PERFORMANCE
OF PROCEDURES OTHER THAN
THOSE SPECIFIED IN THE OWNER’S
MANUAL MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.

VORSICHT: DIE VERWENDUNG VON
ANDEREN STEURUNGEN ODER
EINSTELLUNGEN ODER DAS
DURCHFÜHREN VON ANDEREN
VORGÄNGEN ALS IN DER
BEDIENUNGSANLEITUNG
BESCHRIEBEN KÖNNEN
GEFÄHRLICHE
STRAHLENEXPOSITIONEN ZUR
FOLGE HABEN.

User’s Manual xv

Preface

Congratulations on your purchase of the Qosmio F60 Series computer.
This powerful notebook computer provides excellent expansion capability,
includes multimedia functionality, and is designed to provide years of
reliable, high-performance computing.

This series of computers includes models with built-in TV tuners. When you
wish to display a play CD/DVD before starting Windows

CD/DVD panel on the computer (or the same buttons on the remote
controller). In order to watch television before starting Windows, use the
Full size remote controller. When Windows is running, you can display or
record a TV program using the My TV feature of Media Center or the Full
size remote controller.

This manual tells how to set up and begin using your Qosmio F60 Series
computer. It also provides detailed information on configuring your
computer, basic operations and care, using optional devices and
troubleshooting.

If you are a new user of computers or if you’re new to portable computing,
first read over the Chapter 1, Getting Started and Chapter 3, Hardware,

Utilities and Options chapters to familiarize yourself with the computer’s

features, components and accessory devices. Then read Chapter 1,

Getting Started for step-by-step instructions on setting up your computer.

If you are an experienced computer user, please continue reading the
preface to learn how this manual is organized, then become acquainted
with this manual by browsing through its pages. Be sure to read the Special

features section in Chapter 3, Hardware, Utilities and Options, to learn

about features that are uncommon or unique to this computer, as well as
the section on Chapter 7, HW Setup, to understand how to setup and
configure these features.

Read Chapter 3, Hardware, Utilities and Options if connecting optional
products or external devices.

®

, touch the

Conventions

This manual uses the following formats to describe, identify, and highlight
terms and operating procedures.

User’s Manual xvi

Abbreviations

On first appearance, and whenever necessary for clarity, abbreviations are
enclosed in parentheses following their definition. For example: Read Only
Memory (ROM). Acronyms are also defined in the Glossary.

Icons

Icons identify ports, dials, and other parts of your computer. The indicator
panel also uses icons to identify the components it is providing information
on.

Keys

The keyboard keys are used in the text to describe many computer
operations. A distinctive typeface identifies the key top symbols as they
appear on the keyboard. For example, ENTER identifies the ENTER key.

Key operation

Some operations require you to simultaneously use two or more keys. We
identify such operations by the key top symbols separated by a plus sign (+).
For example, CTRL + C means you must hold down CTRL and at the same
time press C. If three keys are used, hold down the first two and at the same
time press the third.

Qosmio F60 Series

ABC When procedures require an action such as

clicking an icon or entering text, the icon's name
or the text you are to type in is represented in the
typeface you see to the left.

Display

S

ABC

Names of windows or icons or text generated by
the computer that appear on its display screen
are presented in the type face you see to the left.

Messages

Messages are used in this manual to bring important information to your
attention. Each type of message is identified as shown below.

Pay attention! A caution informs you that improper use of equipment or
failure to follow instructions may cause data loss or damage your
equipment.

Please read. A note is a hint or advice that helps you make best use of
your equipment.

User’s Manual xvii

Indicates a potentially hazardous situation, which could result in death or
serious injury, if you do not follow instructions.

Terminology

This term is defined in this document as follows:

Qosmio F60 Series

Start

HDD or Hard disk
drive

The word "Start" refers to the " " button in
Windows® 7.

Some models are equipped with a "Solid State
Drive (SSD)" instead of a hard disk drive.

In this manual, the word "HDD" or "Hard disk
drive" also refers to the SSD unless otherwise
stated.

User’s Manual xviii

General Precautions

TOSHIBA computers are designed to optimize safety, minimize strain and
withstand the rigors of portability. However, certain precautions should be
observed to further reduce the risk of personal injury or damage to the
computer.

Be certain to read the general precautions below and to note the cautions
included in the text of the manual.

Provide adequate ventilation

■ Always make sure your computer and AC adaptor have adequate

ventilation and are protected from overheating when the power is
turned on or when an AC adaptor is connected to a power outlet (even if
your computer is in Sleep Mode). In this condition, observe the
following:

■ Never cover your computer or AC adaptor with any object.

■ Never place your computer or AC adaptor near a heat source, such

as anelectric blanket or heater.

■ Never cover or block the air vents including those located at the

base of the computer.

■ Always operate your computer on a hard flat surface. Using your

computer on a carpet or other soft material can block the vents.

■ Always provide sufficient space around the computer.

■ Overheating your computer or AC adaptor could cause system failure,

computer or AC adaptor damage or a fire, possibly resulting in serious
injury.

User’s Manual xix

Creating a computer-friendly environment

Place the computer on a flat surface that is large enough for the computer
and any other items you are using, such as a printer.

Leave enough space around the computer and other equipment to provide
adequate ventilation. Otherwise, they may overheat.

To keep your computer in prime operating condition, protect your work area
from:

■ Dust, moisture, and direct sunlight.

■ Equipment that generates a strong electromagnetic field, such as

stereo speakers (other than speakers that are connected to the
computer) or speakerphones.

■ Rapid changes in temperature or humidity and sources of temperature

change such as air conditioner vents or heaters.

■ Extreme heat, cold, or humidity.

■ Liquids and corrosive chemicals.

Stress injury

Carefully read the Instruction Manual for Safety and Comfort. It contains
information on the prevention of stress injuries to your hands and wrists
that can be caused by extensive keyboard use. Instruction Manual for
Safety and Comfort also includes information on work space design,
posture and lighting that can help reduce physical stress.

Qosmio F60 Series

Heat injury

■ Avoid prolonged physical contact with the computer. If the computer is

used for long periods, its surface can become very warm. While the
temperature will not feel hot to the touch, if you maintain physical
contact with the computer for a long time, for example if you rest the
computer on your lap or if you keep your hands on the palm rest, your
skin might suffer a low-heat injury.

■ If the computer has been used for a long time, avoid direct contact with

the metal plate supporting the various interface ports as this can
become hot.

■ The surface of the AC adaptor can become hot when in use but this

condition does not indicate a malfunction. If you need to transport the
AC adaptor, you should disconnect it and let it cool before moving it.

■ Do not lay the AC adaptor on a material that is sensitive to heat as the

material could become damaged.

User’s Manual xx

Pressure or impact damage

Do not apply heavy pressure to the computer or subject it to any form of
strong impact as this can damage the computer's components or otherwise
cause it to malfunction.

Mobile phones

Please be aware that the use of mobile phones can interfere with the audio
system. The operation of the computer will not be impaired in any way, but
it is recommended that a minimum distance of 30cm is maintained between
the computer and a mobile phone that is in use.

Instruction Manual for Safety and Comfort

All important information on the safe and proper use of this computer is
described in the enclosed Instruction Manual for Safety and Comfort. Be
sure to read it before using the computer.

Qosmio F60 Series

User’s Manual xxi

Qosmio F60 Series

1

1

1

The cautions on use of a Qosmio F60 Series computer

1. Clean any dust accumulated on the computer's cooling vents.
The cooling vents are located on the left side and underside of the
computer.

When you use your computer in a dusty area, dirt and debris may
accumulate on the cooling vents at the under side of your unit. If this
occurs, the accumulated dust can cause insufficient heat dissipation which
may result in the computer shutting down during use. Carefully clean the
dust from the vents using a vacuum cleaner.

2. Cooling vents on the underside and left side of the computer.

1. Cooling vents

Cooling vents

To prevent possible overheating of the CPU, make sure the cooling fan's
air intake is not blocked. The fan draws in air by creating a vacuum. If the
fan is blocked, it could cause the CPU to run at a lower performance level
or cause the computer to shut down. Loose items such as notebook and
tissue paper, plastic wrappers, or other similar materials can block the air
intake, preventing air from reaching the CPU. Do not use the computer on
surfaces with objects that can be drawn in by the cooling fan.

User’s Manual xxii

Getting Started

This chapter provides an equipment checklist, and it identifies the
computer’s features, options and accessories.

Some of the features described in this manual may not function properly if
you use an operating system that was not pre-installed by TOSHIBA.

Equipment checklist

Carefully unpack your computer, taking care to save the box and packaging
materials for future use.

Hardware

Check to make sure you have all the following items:

■ Qosmio F60 Series Portable Personal Computer

■ AC adaptor and power cord (2-pin plug or 3-pin plug)

■ Battery pack (Is pre-installed in some computer)

■ Remote controller (Is included with some models)

■ Two AA manganese batteries (for remote controller)

■ Cleaning cloth (Is included with some models)

Chapter 1

■ Some models are included with a remote controller.

■ Use the cleaning cloth to wipe away dust, fingerprints and similar from

the keyboard, palm rest and other parts. For precautions on use refer to
the Using the cleaning cloth section in Chapter4, Operating Basics.

User’s Manual 1-1

Documentation

■ Qosmio F60 Series Portable Personal Computer User’s Manual

(User’s Manual)

■ Instruction Manual for Safety and Comfort

■ End User License Agreement

If any of the items are missing or damaged, contact your dealer
immediately.

Software

The following Windows operating system and utility software are pre­installed.

■ Windows® 7

■ TOSHIBA Value Added Package

®

■ Corel DVD MovieFactory

■ TOSHIBA Face Recognition

■ TOSHIBA PC Health Monitor

■ TOSHIBA Disc Creator

■ TOSHIBA HDD Protection (Is preinstalled in some models)

■ TOSHIBA HDD/SSD Alert

■ TOSHIBA Recovery Media Creator

■ TOSHIBA eco Utility

■ TOSHIBA ConfigFree™

■ TOSHIBA Assist

■ TOSHIBA USB Sleep and Charge Utility

■ TOSHIBA Password Utility

■ TOSHIBA DVD PLAYER

■ WinDVD BD for TOSHIBA (Is preinstalled in some models)

■ Windows Mobility Center

■ Online Manual

■ Qosmio F60 Series User’s Manual (This manual)

(Is preinstalled in some models)

Getting Started

User’s Manual 1-2

Getting Started

This chapter provides basic information to start using your computer. It
covers the following topics:

■ All users should be sure to read the section Starting up for the first time.

■ Be sure to read the enclosed Instruction Manual for Safety and Comfort

for information on the safe and proper use of this computer. It is
intended to help you be more comfortable and productive while using a
notebook computer. By following the recommendations in it you may
reduce your chance of developing a painful or disabling injury to your
hand, arms, shoulders or neck.

■ Connecting the AC adaptor

■ Opening the display

■ Turning on the power

■ Starting up for the first time

■ Turning off the power

■ Restarting the computer

■ System Recovery Options

■ Creating Recovery Media

■ Restoring the pre-installed software from the Recovery hard disk drive

■ Restoring the pre-installed software from your created Recovery Media

■ Use a virus-check program and make sure it is updated regularly.

■ Never format storage media without checking its content - formatting

destroys all stored data.

■ It is a good idea to periodically back up the internal hard disk drive or

other main storage device to external media. General storage media is
not durable or stable over long periods of time and under certain
conditions may result in data loss.

■ Before you install a device or application, save any data in memory to

the hard disk drive or other storage media. Failure to do so may result
in the loss of data.

Getting Started

User’s Manual 1-3

Connecting the AC adaptor

Attach the AC adaptor when you need to charge the battery or you want to
operate from AC power. It is also the fastest way to get started, because
the battery pack will need to be charged before you can operate from
battery power.

The AC adaptor can be connected to any power source supplying from 100
to 240 volts and 50 or 60 hertz. For details on using the AC adaptor to
charge the battery pack, refer to Chapter 6, Power and Power-Up Modes.

■ Always use the TOSHIBA AC adaptor that was included with your

computer or use AC adaptors specified by TOSHIBA to avoid any risk
of fire or other damage to the computer. Use of an incompatible AC
adaptor could cause fire or damage to the computer possibly resulting
in serious injury. TOSHIBA assumes no liability for any damage caused
by use of an incompatible adaptor.

■ Never plug the AC adaptor into a power source that does not

correspond to both the voltage and the frequency specified on the
regulatory label of the unit. Failure to do so could result in a fire or
electric shock, possibly resulting in serious injury.

■ Always use or purchase power cables that comply with the legal

voltage and frequency specifications and requirements in the country of
use. Failure to do so could result in a fire or electric shock, possibly
resulting in serious injury.

■ The supplied power cord conforms to safety rules and regulations in

the region the product is bought and should not be used outside this
region. For use in other regions, please buy power cords that conform
to safety rules and regulations in the particular region.

■ Do not use a 3-pin to 2-pin conversion plug.

■ When you connect the AC adaptor to the computer, always follow the

steps in the exact order as described in the User’s Manual. Connecting
the power cable to a live electrical outlet should be the last step
otherwise the adaptor DC output plug could hold an electrical charge
and cause an electrical shock or minor bodily injury when touched. As
a general safety precaution, avoid touching any metal parts.

■ Never place your computer or AC adaptor on a wooden surface,

furniture, or any other surface that could be marred by exposure to heat
since the computer base and AC adaptor's surface increase in
temperature during normal use.

■ Always place your computer or AC adaptor on a flat and hard surface

that is resistant to heat damage.

Refer to the enclosed Instruction Manual for Safety and Comfort for
detailed precautions and handling instructions.

Getting Started

User’s Manual 1-4

Getting Started

1

2

1. Connect the power cord to the AC adaptor.

Figure 1-1 Connecting the power cord to the AC adaptor (2-pin plug)

Figure 1-2 Connecting the power cord to the AC adaptor (3-pin plug)

Either a 2-pin or 3-pin adaptor/cord will be included with the computer
depending on the model.

2. Connect the AC adaptor's DC output plug to the DC IN 19V jack on the
back of the computer.

1. DC IN 19V jack

Figure 1-3 Connecting the DC output plug to the computer

2. DC output plug

3. Plug the power cord into a live wall outlet - the Battery and DC IN
indicators on the front of the computer should glow.

User’s Manual 1-5

Opening the display

1

The display panel can be opened to a wide range of angles for optimal
viewing.

While holding down the palm rest with one hand so that the main body of
the computer is not raised, slowly lift the display panel - this will allow the
angle of the display panel to be adjusted to provide optimum clarity.

1. Display panel

Figure 1-4 Opening the display

Use reasonable care when opening and closing the display panel. Opening
it vigorously or slamming it shut could damage the computer.

Getting Started

User’s Manual 1-6

■ As the display panel cannot be opened until 180 degrees, please be

careful of the angle when flipping open the display panel.

■ Be careful not to open the display panel too far as this could put stress

on the display panel’s hinges and cause damage.

■ Do not press or push on the display panel.

■ Do not lift the computer by the display panel.

■ Do not close the display panel with pens or any other objects left in

between the display panel and the keyboard.

■ When opening or closing the display panel, place one hand on the

palm rest to hold the computer in place and use the other hand to
slowly open or close the display panel (Do not use excessive force
when opening or closing the display panel).

Turning on the power

This section describes how to turn on the power - the Power indicator will
then indicate the status. Please refer to the Monitoring of power condition
section in Chapter 6, Power and Power-Up Modes for more information.

Getting Started

■ After you turn on the power for the first time, do not turn it off until you

have set up the operating system. Please refer to the section Starting

up for the first time for more information.

■ Volume cannot be adjusted during Windows Setup.

1. Open the display panel.

User’s Manual 1-7

2. Press and hold the computer's power button for two or three seconds.

1

1. Power button

Figure 1-5 Turning on the power

Starting up for the first time

The Windows 7 Startup Screen will be the first screen displayed when you
turn on the power. Follow the on-screen instructions on each screen in
order to properly install the operating system.

When it is displayed, be sure to read the Software License Terms
carefully.

Turning off the power

The power can be turned off in one of three modes, either Shut Down
Mode, Hibernation Mode or Sleep Mode.

Getting Started

Shut Down Mode

When you turn off the power in Shut Down Mode no data will be saved and
the computer will boot to the operating system's main screen the next time
it is turned on.

1. If you have entered data, either save it to the hard disk drive or to other
storage media.

2. Make sure all disk/disc activity has stopped before removing the
CD/DVD or floppy diskette.

■ Make sure the Hard Disk Drive indicator is off. If you turn off the power

while a disk (disc) is being accessed, you may lose data or damage the
disk.

■ Never turn off the power while an application is running. Doing so could

cause loss of data.

■ Never turn off the power, disconnect an external storage device or

remove storage media during data read/write. Doing so can cause data
loss.

3. Click Start.

User’s Manual 1-8

Getting Started

4. Click the Shut down button ( ).

5. Turn off any peripheral devices connected to your computer.

Do not turn the computer or peripheral devices back on immediately - wait
a short period to avoid any potential damage.

Sleep Mode

If you have to interrupt your work, you are able to turn off the power without
exiting from your software by placing the computer into Sleep Mode. In this
mode data is maintained in the computer's main memory so that when you
turn on the power again, you can continue working right where you left off.

When you have to turn off your computer aboard an aircraft or in places
where electronic devices are regulated or controlled, always completely
shut down the computer. This includes turning off any wireless
communication devices, and canceling settings that reactivate the
computer automatically, such as a timer recording function. Failure to
completely shut down the computer in this way could allow the operating
system to reactivate and run pre-programmed tasks or preserve unsaved
data, which could interfere with aviation or other systems, possibly causing
serious injury.

■ Before entering Sleep Mode, be sure to save your data.

■ Do not install or remove a memory module while the computer is in

Sleep Mode. The computer or the memory module could be damaged.

■ Do not remove the battery pack while the computer is in Sleep Mode

(unless the computer is connected to an AC power source). Data in
memory could be lost.

■ When the AC adaptor is connected, the computer will go into Sleep

Mode according to the settings in the Power Options (to access it, Start

-> Control Panel -> System and Security -> Power Options).

■ To restore the operation of the computer from Sleep Mode, press and

hold the power button or any key on the keyboard for a short amount of
time. Please note that keyboard keys can only be used if the Wake-up
on Keyboard option is enabled within the HW Setup utility.

■ If the computer enters Sleep Mode while a network application is

active, the application might not be restored when the computer is next
turned on and the system returns from Sleep Mode.

■ To prevent the computer from automatically entering Sleep Mode,

disable Sleep Mode within the Power Options (to access it, Start ->
Control Panel -> System and Security -> Power Options).

■ To use the Hybrid Sleep function, configure it in the Power Options.

User’s Manual 1-9

Getting Started

Benefits of Sleep Mode

The Sleep Mode feature provides the following benefits:

■ Restores the previous working environment more rapidly than does the

Hibernation Mode feature.

■ Saves power by shutting down the system when the computer receives

no input or hardware access for the time period set by the System
Sleep Mode feature.

■ Allows the use of the panel power off feature.

Executing Sleep Mode

You can also enable Sleep Mode by pressing FN + F3 - please refer to
Chapter 5, The Keyboard, for further details.

You can enter Sleep Mode in one of three ways:

■ Click Start, point to the arrow icon ( ) and select

Sleep from the menu.

■ Close the display panel. Please note that this feature must be enabled

within the Power Options (to access it, click Start -> Control Panel ->
System and Security -> Power Options).

■ Press the power button. Please note that this feature must be enabled

within the Power Options (to access it, click Start -> Control Panel ->
System and Security -> Power Options).

When you turn the power back on, you can continue where you left when
you shut down the computer.

■ When the computer is in Sleep Mode, the Power indicator will blink

orange.

■ If you are operating the computer on battery power, you can lengthen

the overall operating time by turning it off into Hibernation Mode - Sleep
Mode will consume more power while the computer is off.

Sleep Mode limitations

Sleep Mode will not function under the following conditions:

■ Power is turned back on immediately after shutting down.

■ Memory circuits are exposed to static electricity or electrical noise.

Hibernation Mode

The Hibernation Mode feature saves the contents of memory to the hard
disk drive when the computer is turned off so that, the next time it is turned
on, the previous state is restored. Please note that the Hibernation Mode
feature does not save the status of any peripheral devices connected to the
computer.

User’s Manual 1-10

Getting Started

■ Save your data. While entering Hibernation Mode, the computer saves

the contents of memory to the hard disk drive. However, for safety
sake, it is best to save your data manually.

■ Data will be lost if you remove the battery or disconnect the AC adaptor

before the save is completed. Wait for the Hard Disk Drive indicator to
go out.

■ Do not install or remove a memory module while the computer is in

Hibernation Mode. Data will be lost.

Benefits of Hibernation Mode

The Hibernation Mode feature provides the following benefits:

■ Saves data to the hard disk drive when the computer automatically

shuts down because of a low battery condition.

■ You can return to your previous working environment immediately when

you turn on the computer.

■ Saves power by shutting down the system when the computer receives

no input or hardware access for the time period set by the System
Hibernate feature.

■ Allows the use of the panel power off feature.

Starting Hibernation Mode

You can also enable Hibernation Mode by pressing FN + F4 - please refer
to Chapter 5, The Keyboard, for further details.

To enter Hibernation Mode, follow the steps below.

1. Click Start.

2. Point to the arrow icon ( ) and then select Hibernate
from the menu.

Automatic Hibernation Mode

The computer can be configured to enter Hibernation Mode automatically
when you press the power button or close the lid. In order to define these
settings, you can follow the steps as described below:

1. Click Start and click the Control Panel.

2. Click System and Security and click Power Options.

3. Click Choose what the power buttons do or Choose what closing
the lid does.

4. Enable the desired Hibernation Mode settings for When I press the
power button and When I close the lid.

5. Click the Save changes button.

User’s Manual 1-11

Data save in Hibernation Mode

When you turn off the power in Hibernation Mode, the computer will take a
moment to save the current data in memory to the hard disk drive. During
this time, the Hard Disk Drive indicator will glow.

After you turn off the computer, and the content of memory has been saved
to the hard disk drive, turn off the power to any peripheral devices.

Do not turn the computer or devices back on immediately. Wait a moment
to let all capacitors fully discharge.

Restarting the computer

Certain conditions require that you reset the computer, for example if:

■ You change certain computer settings.

■ An error occurs and the computer does not respond to your keyboard

commands.

If you need to restart the computer, there are three ways this can be
achieved:

■ Click Start, point to the arrow icon ( ) and then select

Restart from the menu.

■ Press CTRL, ALT and DEL simultaneously (once) to display the menu

window, then select Restart from the Shut down options.

■ Press the power button and hold it down for five seconds. Once the

computer has turned itself off, wait between ten and fifteen seconds
before turning the power on again by pressing the power button.

Getting Started

System Recovery Options

About 1.5GB hidden partition is allocated on the hard disk drive for the
System Recovery Options.

This partition stores files which can be used to repair the system in the
event of a problem.

The System Recovery Options feature will be unusable if this partition is
deleted.

System Recovery Options

The System Recovery Options feature is installed on the hard disk when
shipped from the factory. The System Recovery Options menu includes
tools to repair startup problems, run diagnostics or restore the system.

See the Windows Help and Support content for more information about
Startup Repair.

The System Recovery Options can also be run manually to repair
problems.

User’s Manual 1-12

The procedure is as follows. Follow the instructions shown on the on­screen menu.

1. Turn off the computer.

2. While holding the F8 key, turn on the computer.

3. The Advanced Boot Options menu will be displayed.
Use the arrow keys to select Repair Your Computer and press
ENTER.

4. Follow the on-screen instructions.

Check your Windows® manual for more information on backing up your
system (including the system image backup feature).

System Recovery

This section describes the creation of Recovery Media and their use.

Creating Recovery Media

This section describes how to create Recovery Media.

■ Be sure to connect the AC adaptor when you create Recovery Media.

■ Be sure to close all other software programs except the Recovery

Media Creator.

■ Do not run software such as screen savers which can put a heavy load

on the CPU.

■ Operate the computer at full power.

■ Do not use power-saving features.

■ Do not write to the media when the virus check software is running.

Wait for it to finish, then disable virus detection programs including any
software that checks files automatically in the background.

■ Do not use utilities, including those intended to enhance hard disk drive

access speed. They may cause unstable operation and damage data.

■ Do not shut down/log off or Sleep/Hibernate while writing or rewriting

the media.

■ Set the computer on a level surface and avoid places subjected to

vibrations such as airplanes, trains, or cars.

■ Do not use on unstable tables or other any other unstable surfaces.

Getting Started

A recovery image of the software on your computer is stored on the hard
disk drive, and can be copied to either DVD or USB Flash Memory by using
the following steps:

1. Select either blank DVD or USB Flash Memory.
The application will allow you to choose from a variety of different media

onto which the recovery image can be copied including DVD-R, DVD-R
DL, DVD-RW, DVD+R, DVD+R DL and DVD+RW and USB Flash
Memory.

User’s Manual 1-13

Getting Started

■ Please note that some of the above media may not be compatible with

the optical disc drive installed into your computer. You should therefore
verify the optical disc drive supports the blank media you have chosen
before proceeding.

■ USB Flash Memory will be formatted and all the data in the USB Flash

Memory will be lost when proceeding.

2. Turn on your computer and allow it to load the Windows 7 operating
system from the hard disk drive as normal.

3. Insert the media into the computer.

■ Insert the first blank disc into the optical disc drive tray, or

Insert the USB Flash Memory into one available USB port

4. Double click the Recovery Media Creator icon on the Windows 7
desktop, or select the application from Start Menu.

5. After Recovery Media Creator starts, select the type of media and the
title you wish to copy. The screen will display the number of discs or the
capacity of USB Flash Memory required. Make shure you have a
sufficient number of discs or sufficient capacity of USB Flash Memory
before you proceed with the Recovery Media process.

6. Click the Create button to preceed.

Restoring the pre-installed software from the Recovery hard disk
drive

A portion of the total hard disk drive space is configured as a hidden
recovery partition. This partition stores files which can be used to restore
pre-installed software in the event of a problem.

If you subsequently set up your hard disk drive again, do not change,
delete or add partitions in a manner other than specified in the manual,
otherwise you may find that space for the required software is not available.

In addition, if you use a third-party partitioning program to reconfigure the
partitions on your hard disk drive, you may find that it becomes impossible
to setup your computer.

When the sound mute feature has been activated by pressing the FN +
ESC key, be sure to disable this to allow sounds to be heard before starting

the restore process. Please refer to Chapter 5, The Keyboard, for further
details.

You can not use System Recovery Options if restoring the pre-installed
software without System Recovery Options.

When you reinstall the Windows operating system, the hard disk will be
reformatted and all data will be lost.

1. Turn off your computer.

2. While holding down 0 (zero) key on the keyboard, turn on your
computer.

User’s Manual 1-14

Getting Started

3. A menu will be displayed from which you should follow the on-screen
instructions.

Restoring the pre-installed software from your created Recovery
Media

If the pre-installed files are damaged, you are able to either use the
Recovery Media you have created or the hard disk drive recovery process
to restore the computer to the state it was in when you originally received it.
To perform this restoration, follow the steps below:

When the sound mute feature has been activated by pressing the FN +
ESC key, be sure to disable this to allow sounds to be heard before starting

the restore process. Please refer to Chapter 5,The Keyboard, for further
details.

You can not use System Recovery Options if restoring the pre-installed
software without System Recovery Options.

When you reinstall the Windows operating system, the hard disk will be
reformatted and all data will be lost.

1. Load the Recovery Media into the computer and turn off the computer's
power.

2. While holding down F12 key on the keyboard, turn on your computer ­when the Qosmio logo screen appears, release the F12 key.

3. Use the up and down cursor keys to select the appropriate icon
(CD/DVD-ROM) of your actual recovery media from the menu. Please
refer to the Boot Priority section in Chapter 7, HW Setup for further
information.

4. A menu will be displayed from which you should follow the on-screen
instructions.

When drivers/utilities are installed, you can setup the respective
drivers/utilities from the following place. To open the setup files, Click Start

-> All Programs -> TOSHIBA -> Applications and Drivers.

User’s Manual 1-15

The Grand Tour

1

2

3

This chapter identifies the various components of the computer - it is
recommended that you become familiar with each before you operate the
computer.

Legal Footnote (Non-applicable Icons)*1

For more information regarding Non-applicable Icons, please refer to the
Legal Footnotes section in Appendix H or click the *1 above.

Please handle your computer carefully to avoid scratching or damaging the
surface.

Front with the display closed

The following figure shows the computer’s front with its display panel in the
closed position.

Chapter 2

1. Bridge media slot

2. Wireless communication indicator

Figure 2-1 Front of the computer with display closed

User’s Manual 2-1

3. Infrared receiver window (Is supported with
some models)

The Grand Tour

12345

Left side

Bridge media slot This slot lets you insert an SD/SDHC memory

card, miniSD/microSD Card, Memory Stick
(Duo/PRO/PRO Duo), xD picture card and
MultiMediaCard. Refer to Bridge media slot
section in Chapter 3, Hardware, Utilities and
Options.

Keep foreign metal objects, such as screws, staples and paper clips, out of
the Bridge media slot. Foreign metal objects can create a short circuit,
which can cause damage and fire, possibly resulting in serious injury.

Wireless
communication
indicator

The Wireless communication indicator glows
orange when the Bluetooth and Wireless LAN
functions are turned on.

Only some models are equipped with Bluetooth
and Wireless LAN functions.

Infrared receiver
window

This is a sensor window that receives signals
from the remote controller which is provided with
your computer.

Models which do not include a remote controller are not equipped with an
infrared received so the computer cannot be operated with a remote
controller.

The following figure shows the computer's left side.

1. External monitor port 4. HDMI out port

2. Cooling vents

3. eSATA/USB combo port

Figure 2-2 The left side of the computer

User’s Manual 2-2

5. Universal Serial Bus (USB 2.0) port

The Grand Tour

External monitor
port

This port allows you to connect an external
monitor to the computer.

Cooling vents The cooling vents help keep the processor from

overheating.

Do not block the cooling vents. Keep foreign metal objects, such as
screws, staples and paper clips, out of the cooling vents. Foreign metal
objects can create a short circuit, which can cause damage and fire,
possibly resulting in serious injury.

eSATA/USB combo
port

One eSATA/USB combo port, which complies to
the USB 2.0 standard, is provided on the left
hand side of the computer. The ports with the
icon ( ) has USB Sleep and Charge. This port
has eSATA (External Serial ATA) function.

HDMI out port HDMI out port can connect with Type A

connector HDMI cable.
HDMI cable can send video and audio signals. In

addition to this, it can send and receive control
signals.

Universal Serial Bus
(USB 2.0) port

One Universal Serial Bus port, which complies to
the USB 2.0 standard, is provided on the left
hand side of the computer.

Keep foreign metal objects, such as screws, staples and paper clips, out of
the USB connectors. Foreign metal objects can create a short circuit,
which can cause damage and fire, possibly resulting in serious injury.

Please note that it is not possible to confirm the operation of all functions of
all USB devices that are available. In view of this it may be noted that
some functions associated with a specific device might not operate
properly.

User’s Manual 2-3

Right side

1

2

3

4

1

234

5

6

The Grand Tour

The following figure shows the computer’s right side.

1. Headphone and Line out jack 3. Universal Serial Bus (USB 2.0) ports

2. Microphone and Line in jack

Figure 2-3 The right side of the computer

4. Optical disc drive

Back

Headphone and Line
out jack

This jack allows you to connect a headphone, a
MiniDisc audio component or an external audio
device.

Microphone and Line
in jack

Universal Serial Bus
(USB 2.0) ports

This jack allows you to connect a microphone or
an external audio device.

Two Universal Serial Bus ports, which comply
with the USB 2.0 standard, are provided on the
right hand side of the computer.

Optical disc drive The computer is configured with a DVD Super

Multi drive or a BD-R/RE drive.

The following figure shows the computer’s back.

1. Security lock slot

2. TV antenna port (Is supported with some models)

3. LAN jack 6. Battery release latch

Figure 2-4 The back of the computer

4. DC IN 19V jack

5. Battery safety lock

User’s Manual 2-4

The Grand Tour

Security lock slot A security cable can be attached to this slot and

then connected to a desk or other large object in
order to deter theft of the computer.

TV antenna port Connect the coaxial cable to this port to watch

TV programs on your computer or record them.
The dimensions and shape of the TV antenna

port vary for different regions.
Some models are equipped with a TV tuner.

LAN jack This jack lets you connect to a LAN. The adaptor

has built-in support for Ethernet LAN (10
megabits per second, 10BASE-T), Fast Ethernet
LAN (100 megabits per second, 100BASE-TX)
and Gigabit Ethernet LAN (1000 megabits per
second, 1000BASE-T). Refer to Chapter 4,

Operating Basics, for details.

■ Do not connect any cable other than a LAN cable to the LAN jack. It

could cause damage or malfunction.

■ Do not connect the LAN cable to a power supply. It could cause

damage or malfunction.

DC IN 19V jack The AC adaptor connects to this jack in order to

power the computer and charge its internal
batteries. Please note that you should only use
the model of AC adaptor supplied with the
computer at the time of purchase - using the
wrong AC adaptor can cause damage to the
computer.

Battery safety lock Slide this latch into its 'Unlock' position in order to

release the battery pack ready for removal.

Battery release latch Slide and hold this latch into its 'Unlock' position

in order to release the battery pack ready for
removal.

For more detailed information on removing the
battery pack please refer to Chapter 6, Power

and Power-Up Modes.

User’s Manual 2-5

Underside

1

2

The following figure shows the underside of the computer. You should
ensure that the display is closed before the computer is turned over to
avoid causing any damage.

The Grand Tour

1. Battery pack

Figure 2-5 The underside of the computer

2. Memory module slots

Battery pack The battery pack provides power to the computer

when the AC adaptor is not connected. For more
detailed information on the use and operation of
the battery pack please refer to Chapter 6, Power

and Power-Up Modes.

Memory module
slots

The memory module slots are located here. The
memory module slots allow for the installation,
replacement and removal of additional memory
modules. Please refer to the Additional memory

module section in Chapter 3, Hardware, Utilities

and Options.

User’s Manual 2-6

Front with the display open

1

2

3

4

5

6

7

8

9

10

12

13

14

5

15

This section shows the computer with the display panel open. In order to
open the display, lift the display panel up and position it at a comfortable
viewing angle for you.

The Grand Tour

11

1. Web Camera LED 9. Touch Pad On/Off button

2. Web Camera 10. Touch Pad control buttons

3. Wireless LAN antennas (Not shown) 11. Touch Pad

4. Front operation panel (seven panels) 12. LCD Sensor switch (Not shown)

5. Stereo speakers 13. Power button

6. Bluetooth antenna (Not shown) 14. Display hinge

7. Microphone 15. Display screen

8. System indicators

Figure 2-6 The front of the computer with the display open

User’s Manual 2-7

The Grand Tour

Web Camera LED The Web Camera LED glows when the Web

Camera is operating.

Web Camera Web Camera is a device that allows you to

record video or take photographs with your
computer. You can use it for video chatting or
video conferences using a communication tool
such as Windows Live Messenger. TOSHIBA
Web Camera Application will help you to add
various video effects to your video or photograph.

Enables the transmission of video and use of
video chat via the internet using specialized
applications.

Please refer to the Web Camera section in
Chapter 4, Operating Basics.

Wireless LAN
antennas

Front operation
panel (seven panels)

Some computers in this series are equipped with
the Wireless LAN antennas.

Seven panels are available for use:
eco, Wireless On/Off, Programmable button,

CD/DVD Play/Pause, Mute, volume -, volume +.
These panels allow you to manage Audio/Video,

run applications and access utilities.
Refer to Chapter 8, AV functions for details.

Stereo speakers The speakers emit sound generated by your

software as well as audio alarms, such as low
battery condition, generated by the system.

Keep foreign objects out of the speakers. Never allow metal objects, such
as screws, staples and paper clips, to enter the computer or keyboard.
Foreign metal objects can create a short circuit, which can cause computer
damage and fire, possibly resulting in serious injury.

Bluetooth antenna Some computers in this series are equipped with

a Bluetooth antenna.

Microphone A built-in microphone allows you to import and

record sounds for your application - please refer
to the Sound system section in Chapter 4,
Operating Basics for more information.

System indicators These LED indicators allow you to monitor the

status of various computer functions and are
described in more detail within the System

indicators section.

User’s Manual 2-8

The Grand Tour

Touch Pad On/Off
button

Touch Pad control
buttons

Press this button to enable or disable the Touch
Pad function.

The control buttons located below the Touch Pad
allow you to select menu items or manipulate text
and graphics as designated by the on-screen
pointer.

Touch Pad The Touch Pad located in the center of the palm

rest is used to control the movement of the on­screen pointer. For more information, please
refer to the Using the Touch Pad section in
Chapter 4, Operating Basics.

LCD Sensor switch This switch senses when the display panel is

either closed or opened and activates the Panel
Power Off/On feature as appropriate. For
example, when you close the display panel the
computer enters Hibernation Mode and shuts
itself down and then, when you next open the
display, the computer will automatically start up
and return you to the application you were
previously working on.

You can specify within the Power Options. To
access it, click Start -> Control Panel -> System
and Security -> Power Options.

Do not put any magnetic objects close to this switch as they may cause the
computer to automatically enter Hibernation Mode and shut down even if
the Panel Power Off feature is disabled.

Power button Press this button to turn the computer's power on

and off.

Display hinge The display hinge allows the display panel to be

position at a variety of easy-to-view angles.

Display screen Please be aware that, when the computer is

operating on the AC adaptor, the image
displayed on the internal screen will be
somewhat brighter than when it operates on
battery power. This difference in brightness
levels is intended to save power when operating
on batteries. For more information on the
computer's display, please refer to the Display

Controller and Video mode section in Appendix

B.

User’s Manual 2-9

Indicators

System indicators

The Grand Tour

This section explains indicator functions.

The LED system indicators for specific computer operations glow when
those operations are in progress.

Figure 2-7 System indicators

DC IN The DC IN indicator normally glows white when

power is being correctly supplied from the AC
power adaptor. However, If the output voltage
from the adaptor is abnormal, or if the computer's
power supply malfunctions, this indicator will
flash orange.

Power The Power indicator normally glows white when

Battery The Battery indicator shows the condition of the

Hard Disk Drive The Hard Disk Drive indicator glows white

Bridge media slot The Bridge media slot indicator glows white

the computer is turned on. However, if you turn
the computer off into Sleep Mode, this indicator
will flash orange - approximately one second on,
two seconds off - both while the system is
shutting down and while it remains turned off.

battery's charge - white indicates the battery is
fully charged, orange indicates the battery is
charging, and flashing orange indicates a low
battery condition. Please refer to Chapter 6,

Power and Power-Up Modes for more

information on this feature.

whenever the computer is accessing the built-in
hard disk drive, optical disc drive or eSATA
device.

when the computer is accessing the Bridge
media slot.

User’s Manual 2-10

Keyboard indicators

1

2

The following figures show the positions of the CAPS LOCK indicator and
the NUMLOCK indicators which show the following conditions:

■ When the CAPS LOCK indicator glows, the keyboard will produce

capitals when any letter is typed.

■ When the NUMLOCK indicator glows, the ten key allows you to enter

numbers.

1. CAPS LOCK indicator 2. NUMLOCK indicator

Figure 2-8 Keypad indicators

The Grand Tour

CAPS LOCK This indicator glows green when letter keys are

locked into their uppercase format.

NUMLOCK When the NUMLOCK indicator glows, the ten

key allows you to enter numbers.

User’s Manual 2-11

Optical disc drives

The computer is configured with a DVD Super Multi drive or a BD-R/RE
drive. An ATAPI interface controller is used for optical disc operation. When
the computer is accessing an optical disc, an indicator on the drive glows.

For further information on loading and unloading discs, please refer to the

Using optical disc drives section in Chapter 4, Operating Basics.

Region codes for DVD drives and media

DVD Super Multi drives and their associated media are manufactured
according to the specifications of six marketing regions. When you
purchase DVD-Video, make sure it matches your drive, otherwise it will not
play properly.

Code Region

1 Canada, United States

2 Japan, Europe, South Africa, Middle East

3 South East Asia, East Asia

4 Australia, New Zealand, Pacific Islands, Central

The Grand Tour

America, South America, Caribbean

5 Russia, Indian Subcontinent, Africa, North Korea,

Mongolia

6 China

Region codes for BD drive and media

BD drive and their associated media are manufactured according to the
specifications of three marketing regions. Region codes can be set from
WinDVD BD ([Region] tab in [Setup] dialogue). When you purchase BD
Video, make sure it matches your drive, otherwise it will not play properly.

Code Region

A Canada, United States, Japan, Southeast Asia,

East Asia

B Europe, Australia, New Zealand, Middle East,

C China, India, Russia

User’s Manual 2-12

Africa

Writable discs

This section describes the types of writable CD/DVD/BD discs. Check the
specifications of your drive to see the types of discs it can write. Use
TOSHIBA Disc Creator to write compact discs. Please refer to Chapter 4,

Operating Basics for further information.

CDs

■ CD-R discs can be written only once. The recorded data cannot be

erased or changed.

■ CD-RW discs including multi speed CD-RW discs, high-speed CD-RW

discs and ultra-speed CD-RW discs can be recorded more than once.

DVDs

■ DVD-R, DVD+R, DVD-R (Dual Layer) and DVD+R (Double Layer) discs

can be written only once. The recorded data cannot be erased or
changed.

■ DVD-RW, DVD+RW and DVD-RAM discs can be recorded more than

once.

BDs

■ BD-R discs can be written only once. The recorded data cannot be

erased or changed.

■ BD-RE discs can be recorded more than once.

The Grand Tour

User’s Manual 2-13

BD-R/RE drive

The full-size BD-R/RE drive module lets you record data to writable
CD/DVD/BDs as well as run either 12 cm (4.72") or 8 cm (3.15")
CD/DVD/BDs without using an adaptor.

The read speed is slower at the center of a disc and faster at the outer
edge.

BD read 6 speed (maximum)
BD DL read 6 speed (maximum)
BD-R write 6 speed (maximum)
BD-R DL write 4 speed (maximum)
BD-RE write 2 speed (maximum)
BD-RE DL write 2 speed (maximum)
DVD read 8 speed (maximum)
DVD-R write 8 speed (maximum)
DVD-RW write 6 speed (maximum)
DVD+R write 8 speed (maximum)
DVD+RW write 8 speed (maximum)
DVD-R DL write 4 speed (maximum)
DVD+R DL write 4 speed (maximum)
DVD-RAM write 5 speed (maximum)
CD read 24 speed (maximum)
CD-R write 24 speed (maximum)
CD-RW write 16 speed (maximum, Ultra-speed

media)

The Grand Tour

User’s Manual 2-14

DVD Super Multi drive

The full-size DVD Super Multi drive module lets you record data to
rewritable CD/DVDs as well as run either 12 cm (4.72") or 8cm (3.15")
CD/DVDs without using an adaptor.

The read speed is slower at the center of a disc and faster at the outer
edge.

DVD read 8 speed (maximum)
DVD-R write 8 speed (maximum)
DVD-R DL write 6 speed (maximum)
DVD-RW write 6 speed (maximum)
DVD+R write 8 speed (maximum)
DVD+R DL write 6 speed (maximum)
DVD+RW write 8 speed (maximum)
DVD-RAM write 5 speed (maximum)
CD read 24 speed (maximum)
CD-R write 24 speed (maximum)
CD-RW write 24 speed (maximum, Ultra-speed

media)

The Grand Tour

User’s Manual 2-15

AC adaptor

The AC adaptor can automatically adjust to any voltage ranging from 100 to
240 volts and to a frequency of either 50 or 60 hertz, enabling you to use
this computer in almost all country/region. The adaptor converts AC power
to DC power and reduces the voltage supplied to this computer.

To recharge the battery, simply connect the AC adaptor to a power source
and to the computer. Please refer to Chapter 6, Power and Power-Up

Modes for further information.

The Grand Tour

Figure 2-9 The AC adaptor (2-pin plug)

Figure 2-10 The AC adaptor (3-pin plug)

■ Depending on the model in question, either a 2-pin or 3-pin

adaptor/power lead will be bundled with the computer.

■ Do not use a 3-pin to 2-pin conversion plug.

■ The supplied power cord conforms to safety rules and regulations in

the region the product is bought and should not be used outside of this
region. In order to use the adaptor/computer in other regions, you
should please buy a power cord that conforms to the safety rules and
regulations in that particular region.

Always use the TOSHIBA AC adaptor that was included with your
computer, or use AC adaptors specified by TOSHIBA to avoid any risk of
fire or other damage to the computer. Use of an incompatible AC adaptor
could cause fire or damage to the computer possibly resulting in serious
injury. TOSHIBA assumes no liability for any damage caused by use of an
incompatible adaptor.

User’s Manual 2-16

Chapter 3

Hardware, Utilities and Options

Hardware

This section describes the hardware of your computer.
The actual specifications may vary depending on the model you

purchased.

Processor

CPU Your computer is equipped with one processor

and processor type varies depending on model.
To check which type of processor is included in

your model, open the TOSHIBA PC Diagnostic
Tool Utility by clicking Start -> All Programs ->
TOSHIBA -> Utilities -> PC Diagnostic Tool.

Legal Footnote (CPU)*2

For more information on the CPU, please refer to the Legal Footnotes
section in Appendix H or Click the *2 above.

User’s Manual 3-1

Hardware, Utilities and Options

Memory

Memory slots 1GB, 2GB or 4GB memory modules can be

installed in the computer's two memory slots for a
maximum of 8,192MB system memory.

This computer can be equipped with memory
modules of a maximum size of 8,192MB. The
actual amount of useable system memory will be
less than the installed memory modules.

Video RAM The memory in a computer's graphics adaptor,

If your computer is configured with more than 3 GB memory, the memory
might be displayed as approximately 3 GB only (depending on the
computer’s hardware specifications).

This is correct because the operating system usually displays the available
memory instead of the physical memory (RAM) built into the computer.

Various system components (like the video adapter’s GPU and PCI
devices like Wireless LAN, etc.) require their own memory space. Since a
32-bit operating system cannot address more than 4 GB of memory, these
system resources overlap the physical memory. It is a technical limitation
that the overlapped memory is not available to the operating system. Even
though some tools might display the actual physical memory built into your
computer, the memory available to the operating system will still be
approximately 3 GB only.

used to store the image displayed on a bitmap
display.

Start -> Control Panel -> Appearance and
Personalization -> Display -> Adjust
resolution.

The amount of Video RAM can be verified by
clicking the Advanced settings button in the
Display Settings window.

The amount of Total Available Graphics memory
will vary be between 1 and 2 MB depending upon
system configuration.

Legal Footnote (Memory (Main System))*3

For more information regarding Memory (Main System), please refer to the
Legal Footnotes section in Appendix H or click the *3 above.

Toshiba Quad Core
HD Processor (Is
supported with some
models)

User’s Manual 3-2

A co-processor specialized for media streaming
processes (real-time image processing such as
image processing and image recognition) is
installed.

Power

Hardware, Utilities and Options

Battery pack The computer is powered by one rechargeable

lithium-ion battery pack (48Wh).

Legal Footnote (Battery Life)*4

For more information regarding Battery Life, please refer to the Legal
Footnotes section in Appendix H or click the *4 above.

RTC battery The internal RTC battery backs up the Real Time

AC adaptor The AC adaptor provides power to the system

Clock (RTC) and calendar.

and recharges the batteries when they are low. It
comes with a detachable power cord which will
either have a 2-pin or 3-pin plug enclosure.

As the AC adaptor is universal, it can receive a
range of AC voltages from 100 to 240 volts,
however you should note that the output current
varies among different models. Using the wrong
adaptor can damage your computer. Refer to the

AC adaptor section in Chapter 2, The Grand

To ur .

Disks

Hard disk drive or
Solid state drive

This computer is equipped with the following
types of hard disk drive (HDD). The capacity of
each hard disk drive model is different.

Some models are equipped with a "Solid State
Drive (SSD)" instead of a hard disk drive.

■ HDD

■ 320GB

■ 400GB

■ 500GB

■ 640GB

■ SSD

■ 256GB

Please note that part of the hard disk or Solid
state drive's overall capacity is reserved as
administration space. Additional HDD/SSD drive
sizes may be introduced.

User’s Manual 3-3

Hardware, Utilities and Options

■ In this manual, the word "HDD" or "Hard disk drive" also refers to the

SSD unless otherwise stated.

■ SSD is a large-capacity storage media which uses Solid-State Memory

in place of a magnetic disk of the hard disk.

Under certain unusual conditions of prolonged non-use and/or exposure to
high temperatures, the SSD may be vulnerable to data retention errors.

Legal Footnote (Hard Disk Drive (HDD) Capacity)*5

For more information regarding Hard Disk Drive (HDD) Capacity, please
refer to the Legal Footnotes section in Appendix H or click the *5 above.

User’s Manual 3-4

Hardware, Utilities and Options

Optical disc drive

BD-R/RE drive Some models are equipped with a full-size BD-

R/RE drive module that lets you record data to
rewritable CD/DVD/BDs. It reads BD-ROM discs
at a maximum 6x speed, BD-ROM (DL) discs at
a maximum 6x speed, DVD-ROM's at a
maximum 8x speed and CD-ROM's at a
maximum 24x speed. It writes CD-R's at up to
24x speed, CD-RW's at up to 16x speed, DVD­R's at a maximum 8x speed, DVD-RW's at a
maximum 6x speed. DVD+R's at a maximum 8x
speed, DVD+RW's at a maximum 8x speed,
DVD+R(DL) discs at a maximum 4x speed, DVD­R(DL) discs at a maximun 4x speed, DVD-RAM
discs at a maximum 5x speed, BD-R discs at a
maximum 6x speed, BD-R (DL) discs at a
maximum 4x speed, BD-RE discs at a maximum
2x speed and BD-RE (DL) discs at a maximum
2x speed. It supports the following formats:

■ BD-ROM

■ BD-ROM (DL)

■ BD-R

■ BD-R (DL)

■ BD-RE

■ BD-RE (DL)

■ DVD-ROM

■ DVD-Video

■ DVD-R

■ DVD-RW

■ DVD+R

■ DVD+RW

■ DVD-RAM

■ DVD+R DL

■ DVD-R DL

■ CD-DA

■ CD-Text

■ Photo CD (single/multi-session)

■ CD-ROM Mode 1, Mode 2

■ CD-ROMXA Mode 2 (Form1, Form2)

■ Enhanced CD (CD-EXTRA)

■ CD-G (Audio CD only)

■ Addressing Method 2

User’s Manual 3-5

Hardware, Utilities and Options

DVD Super Multi
drive

DVD Super Multi
drive with
Labelflash™

The drive reads DVD-ROM's at a maximum 8x
speed and CD-ROM's at a maximum 24x speed,
and writes CD-R's and CD-RW's at up to 24x
speed, DVD-R's, DVD+R's and DVD+RW's at up
to 8x speed, DVD-RW's, DVD-R (Dual Layer)
and DVD+R (Double Layer) at up to 6x speed,
DVD-RAM at up to 5x speed, and supports the
following formats:

■ CD-R

■ CD-RW

■ DVD-ROM

■ DVD-Video

■ CD-DA

■ CD-Text

■ Photo CD™ (single/multi-session)

■ CD-ROM Mode 1, Mode 2

■ CD-ROM XA Mode 2 (Form1, Form2)

■ Enhanced CD (CD-EXTRA)

■ Addressing Method 2

■ DVD-R

■ DVD-R (Dual Layer)

■ DVD-RW

■ DVD+R

■ DVD+R (Double Layer)

■ DVD+RW

■ DVD-RAM

Some models are equipped with a full-size DVD
Super Multi drive module that lets you run CD's
or DVD's without using an adaptor.

The drive reads DVD-ROM's at a maximum 8x
speed and CD-ROM's at a maximum 24x speed,
and writes CD-R's and CD-RW's at up to 24x
speed, DVD-R's, DVD+R's and DVD+RW's at up
to 8x speed, DVD-RW's, DVD-R (Dual Layer)
and DVD+R (Double Layer) at up to 6x speed,
DVD-RAM at up to 5x speed. This drive supports
the same formats as the DVD Super Multi drive.

Some models are equipped with a full-size DVD
Super Multi drive module that lets you run CD's
or DVD's without using an adaptor.

User’s Manual 3-6

Hardware, Utilities and Options

Display

The computer's internal display panel supports high-resolution video
graphics and can be set to a wide range of viewing angles for maximum
comfort and readability.

Display panel 15.6" TFT LCD screen, 32 million colors, with the

following resolution:

■ HD, 1366 horizontal x 768 vertical pixels

Legal Footnote (LCD)*6

For more information regarding the LCD, please refer to the Legal
Footnotes section in Appendix H or click the *6 above.

Graphics controller The graphics controller maximizes display

performance. Refer to Display Controller and

Video mode section in Appendix B for more

information.

Legal Footnote (Graphics Processor Unit ("GPU"))*7

For more information regarding the Graphics Processor Unit ("GPU"),
please refer to the Legal Footnotes section in Appendix H or click the *7
above.

Keyboard

Built-in The internal keyboard provides the dedicated

numeric keys, dedicated cursor control keys,

and Keys. The keyboard is compatible
with the IBM
Chapter 5, The Keyboard, for details.

®

enhanced keyboard. Refer to

Pointing Device

Built-in Touch Pad The integrated Touch Pad and control buttons in

the palm rest allow control of the on-screen
pointer and support functions such as the
scrolling of windows.

Ports

External monitor This port provides 15-pin, analog VGA port.

This port allows you to connect an external
monitor to the computer.

User’s Manual 3-7

Hardware, Utilities and Options

Universal Serial Bus
(USB 2.0)

The computer supports multiple Universal Serial
Bus ports that comply with the USB 2.0 standard.

One of the USB ports has eSATA (External Serial
ATA) function.

eSATA/USB combo
port

One eSATA/Universal Serial Bus (USB) combo
enables a chain connection of USB-equipped or
eSATA-equipped devices to your computer
through the port.

The ports with the icon ( ) has USB Sleep and

Charge.

Please note that it is not possible to confirm the operation of all functions of
all USB devices that are available. In view of this it may be noted that some
functions associated with a specific device might not operate properly.

Slots

Bridge media This slot lets you insert an SD™/SDHC™

memory card, miniSD™/microSD™ Card,
Memory Stick

®

(Duo™/PRO™/PRO Duo™), xD­Picture Card™ and MultiMediaCard™. Refer to
Chapter 3, Hardware, Utilities and Options.

Multimedia

Sound system The integrated sound system provides support

for the computer's internal speakers and
microphone, as allowing an external microphone
and headphones to be connected via the
appropriate jacks.

Web Camera Web Camera is a device that allows you to

record video or take photographs with your
computer. You can use it for video chatting or
video conferences using a communication tool
such as Windows Live Messenger. TOSHIBA
Web Camera Application will help you to add
various video effects to your video or photograph.

Please refer to the Web Camera section in
Chapter 4, Operating Basics.

TV antenna port (Is
supported with some
models)

Connect the coaxial cable to this port to watch
TV programs on your computer or record them.

The dimensions and shape of the TV antenna
port vary for different regions.

User’s Manual 3-8

Hardware, Utilities and Options

HDMI out port HDMI out port can connect with Type A

connector HDMI cable.
HDMI cable can send video and audio signals. In

addition to this, it can send and receive control
signals.

By connecting a TV which supports HDMI
Control to this port, the remote control for the
connected TV can be used to operate some of
the computer functions.

Refer to the REGZA Link (PC Control) section in
Chapter 3, Hardware, Utilities and Options, for
more details.

Headphone and Line
out jack

This jack lets you connect digital speakers, a
stereo headphone (16 ohm minimum) or a stereo
device for audio output. When you connect a
digital speaker or headphones, the internal
speaker is automatically disabled.

Microphone and Line
in jack

A 3.5mm mini microphone jack enables
connection of a three-conductor mini jack for
stereo microphone input, and connection of a
stereo device for audio input.

TV Tuner TV Tuner enables watching and recording TV

programs. Some models are equipped with the
TV Tuner.

Infrared receiver
window

This is a sensor window that receives signals
from the remote controller which is provided with
your computer.

Models which do not include a remote controller
are not equipped with an infrared received so the
computer cannot be operated with a remote
controller.

Remote controller Use this device to navigate when watching TV or

playing CDs/DVDs.
Some models are equipped with a remote

controller.

Some models are included with a remote controller.

User’s Manual 3-9

Communications

Hardware, Utilities and Options

LAN The computer has built-in support for Ethernet

LAN (10 megabits per second, 10BASE-T), Fast
Ethernet LAN (100 megabits per second,
100BASE-TX) and Gigabit Ethernet LAN (1000
megabits per second, 1000BASE-T).

It is pre-installed as a standard device in some
markets.

Bluetooth

™

Some computers in this series have Bluetooth
wireless communication function which
eliminates the need for cables between
electronic devices such as computers, printers
and mobile phones. When it is enabled,
Bluetooth provides the wireless personal area
network environment which is safe and
trustworthy, that is quick and easy.

Wireless LAN Some computers in this series are equipped with

a Wireless LAN module that is compatible with
other LAN systems based on Direct Sequence
Spread Spectrum/Orthogonal Frequency Division
Multiplexing radio technology that complies with
the IEEE 802.11 Standard.

The transmission speed over the wireless LAN, and the distance over
which the wireless LAN can reach, may vary depending on surrounding
electromagnetic environment, obstacles, access point design and
configuration, client design and software/hardware configurations. The
transmission rate described is the theoretical maximum speed as specified
under the appropriate standard - the actual transmission speed will be
lower than the theoretical maximum speed.

Legal Footnote (Wireless LAN)*8

For more information regarding Wireless LAN, please refer to the Legal
Footnotes section in Appendix H or click the *8 above.

Security

Security lock slot Connects a security lock to anchor the computer

to a desk or other large object.

User’s Manual 3-10

Special features

The following features are either unique to TOSHIBA computers or are
advanced features which make the computer more convenient to use.

Access each function using the following procedures.
*1 To access the Power Options, click Start -> Control Panel -> System

and Security -> Power Options.

Hardware, Utilities and Options

Hot keys Hot keys are specific key combinations that let

you quickly change the system configuration
directly from the keyboard without running a
system program.

Display automatic
power off

*1

This feature automatically cuts off power to the
computer's display panel when there is no
keyboard input for a specified time, with power
being restored the next time a key is pressed.
This can be specified in the Power Options.

HDD automatic
power off

*1

This feature automatically cuts off power to the
hard disk drive when it is not accessed for a
specified time, with power being restored when
the hard disk drive is next accessed. This can be
specified in the Power Options.

System automatic
Sleep/Hibernation

*1

Mode

This feature automatically shuts down the system
into either Sleep Mode or Hibernation Mode when
there is no input or hardware access for a
specified time. This can be specified in the Power
Options.

Power on password Two levels of password security, supervisor and

user, are available to prevent unauthorized
access to your computer.

Instant security A specific hot key function automatically locks the

system providing data security.

Intelligent power
supply

*1

A microprocessor in the computer's intelligent
power supply detects the battery's charge,
automatically calculates the remaining battery
capacity and protects electronic components
from abnormal conditions such as a voltage
overload from the AC adaptor. This can be
specified in the Power Options.

*1

Battery save mode

This feature lets you configure the computer in
order to save battery power. This can be
specified in the Power Options.

User’s Manual 3-11

Hardware, Utilities and Options

Panel power on/off *1This feature automatically turns power to the

computer off when the display panel is closed,
and turns it back on when the display panel is
opened. This can be specified in the Power
Options.

Low battery
automatic

Hibernation Mode

When battery power is exhausted to the point that
computer operation cannot be continued, the

*1

system automatically enters Hibernation Mode
and shuts itself down. This can be specified in the
Power Options.

Heat dispersal

*1

To protect against overheating, the processor has
an internal temperature sensor so that, if the
computer's internal temperature rises to a certain
level, the cooling fan is turned on or the
processing speed is lowered. This can be
specified in the Power Options.

If the processor's temperature reaches an unacceptably high level with
either setting, the computer will automatically shuts down to prevent any
damage - in this instance all unsaved data in memory will be lost.

TOSHIBA HDD
Protection

This feature uses the acceleration sensor built in
the computer to detect vibration and shocks, and
automatically moves the hard disk drive's
read/write head to a safe position in order to
reduce the risk of damage that could be caused
by head-to-disk contact. Refer to the Using the

Hard Disk Drive (HDD) Protection section in

Chapter 4, Operating Basics, for more details.

■ The TOSHIBA HDD Protection function does not guarantee that the

hard disk drive will not be damaged.

■ TOSHIBA HDD Protection cannot be used in models that are equipped

with SSD.

Optical Drive Auto
Lock

This function is provided with some models.
This function automatically locks the optical disc

drive eject button if the computer detects any
vibration or other shocks while running on the
battery.

This function prevents the disc tray from opening
even if the eject button is pushed unexpectedly.
Refer to the Optical Drive Auto Lock section in
Chapter 4, Operating Basics, for more details.

User’s Manual 3-12

Hardware, Utilities and Options

Hibernation Mode This feature lets you turn off the power to the

computer without exiting from your software. The
contents of main memory are automatically
saved to the hard disk drive so that when you
next turn the power on again, you can continue
working right where you left off. Refer to the

Turning off the power section in Chapter 1,

Getting Started, for more details.

Sleep Mode If you have to interrupt your work, you can use

this feature to allow you to turn off power to the
computer without exiting from your software. Data
is maintained in the computer's main memory so
that when you next turn on the power, you can
continue working right where you left off.

USB Sleep and
Charge function

This feature allows you to charge USB­compatible external devices such as mobile
phones or portable digital music players via the
USB port when your computer is in Sleep Mode,
Hibernation Mode or in the shutdown state.

This function is worked by the USB Sleep and
Charge Utility. For more information, please refer
to the Using the TOSHIBA USB Sleep and

Charge Utility section in Chapter 4, Operating

Basics.

USB Wakeup
function

This function restores the computer from Sleep
Mode depending on the external devices
connected to the USB ports.

For example, if a mouse or USB keyboard is
connected to a USB port, moving the
mouse/keyboard will wakeup the computer.

The "USB Wakeup function" operates under
Windows 7 operating system and it works for all
USB ports.

TOSHIBA PC Health
Monitor

The TOSHIBA PC Health Monitor application
proactively monitors a number of system
functions such as power consumption and battery
health, informing you of significant system
conditions. This application recognizes the
system and individual component serial numbers,
and will track specific activities related to the
computer and their usage.

Refer to Appendix G, TOSHIBA PC Health

Monitor.

User’s Manual 3-13

TOSHIBA Value Added Package

This section describes the TOSHIBA Component features pre-installed on
the computer.

Hardware, Utilities and Options

TOSHIBA Power
Saver

TOSHIBA Button
Support

TOSHIBA Zooming
Utility

TOSHIBA PC
Diagnostic Tool

TOSHIBA Password
Utility

TOSHIBA Flash
Cards

HW Setup This utility allows you to customize your

TOSHIBA
Accessibility

TOSHIBA Power Saver provides you with the
features of more various power supply
managements.

This utility controls the following computer panel
functions.

The applications associated with each of the
following panels can be assigned by the user.

■ Panels: Assign applications to the

eco, Programmable button, CD/DVD
Play/Pause, Mute panels.

This utility allows you to enlarge or reduce the
icon size on the Windows Desktop, or the zoom
factor associated with specific supported
applications.

The TOSHIBA PC Diagnostic Tool will display
basic system configuration information and allow
the functionality of some of the computer's built­in hardware devices to be tested.

The TOSHIBA Password utility allows you to set
a password in order to restrict access to the
computer.

The TOSHIBA Flash Cards provide a quick way
to modify selected system functions and to
launch applications.

■ Hot key function

■ TOSHIBA utility launcher function

hardware settings according to the way you work
with the computer and the peripherals you use.

The TOSHIBA Accessibility utility provides
support to movement impaired users when they
need to use the TOSHIBA Hot-key functions. In
use, the utility allows you to make the FN key
'sticky', that is you can press it once, release it,
and they press one of the 'F' keys in order to
access its specific function. When set, the FN
key will remain active until another key is
pressed.

User’s Manual 3-14

Utilities and Applications

This section describes the pre-installed utilities that come with the
computer and details how to start them. For further information on their
operation, please refer to each utility's online manual, help files or
README.TXT file.

Hardware, Utilities and Options

TOSHIBA Face
Recognition

Bluetooth Stack for
Windows by Toshiba

Bluetooth functions cannot be used in models that do not have a Bluetooth
module installed.

TOSHIBA Assist TOSHIBA Assist is a graphical user interface that

TOSHIBA ConfigFree TOSHIBA ConfigFree is a suite of utilities that

TOSHIBA Face Recognition uses a face
verification library to verify the face data of users
when they log in to Windows. If the verification is
successful, the user will be logged into Windows
automatically. The user can thus avoid having to
enter a password or the like, which makes the
login process easier.

For more information, please refer to the Using

the TOSHIBA Face Recognition section in

Chapter 4, Operating Basics.

This software enables communication between
the computer and external Bluetooth devices
such as printers and mobile phones.

provides access to specific tools, utilities and
applications that make the use and configuration
of the computer easier.

To access this utility, click Start -> All Programs

-> TOSHIBA -> Utilities -> TOSHIBA Assist.

improve the ease and control of communication
devices and network connections, help in the
identification of communication problems and
allow the creation of profiles if you need to switch
between different locations and communication
networks. To access this utility, click Start -> All
Programs -> TOSHIBA -> ConfigFree.

User’s Manual 3-15

Hardware, Utilities and Options

TOSHIBA eco Utility This PC is equipped with "eco mode". This mode

slightly lowers performance of some devices to
reduce electric power consumption. You can
realize measurable power savings by using it
continuously. TOSHIBA eco Utility helps you
monitor your power savings by showing
approximate real time power consumption.
Furthermore, it shows approximate accumulated
power consumption and approximate
accumulated power savings when using eco
mode daily, weekly, and monthly. You can track
power savings by using eco mode continuously.

To access this utility, click Start -> All Programs

-> TOSHIBA -> Utilities -> eco Utility.

TOSHIBA Disc
Creator

You can create CD's and DVD's in a number of
formats including audio CD's that can be played
on a standard CD player, and data CD's/DVD's
which can store copies of the files and folders on
your computer's hard disk drive. This software
can be used on models with a DVD Super Multi
drive or a BD-R/RE drive.

To start this utility, click Start -> All Programs ->

TOSHIBA -> CD&DVD Applications -> Disc
Creator.

TOSHIBA DVD-RAM
Utility

This utility has the function of Physical Format
and Write-Protect to DVD-RAM. This utility is
contained the setup module of TOSHIBA Disc
Creator. To start this utility, click Start -> All

Programs -> TOSHIBA -> CD&DVD
Applications -> DVD-RAM Utility.

WinDVD BD for
TOSHIBA

This software is provided for playback of Blu-ray
Disc. It has an on-screen interface and functions.

To start this utility, click Start -> All Programs ->

InterVideo WinDVD -> WinDVD BD for
TOSHIBA.

TOSHIBA HDD/SSD
Alert Utility

This utility includes wizard functions to monitor
the Disk Drive operating status and execute the
system backup.

To access the utility, click Start -> All Programs

-> TOSHIBA -> Utilities -> HDD SSD Alert.

User’s Manual 3-16

Hardware, Utilities and Options

TOSHIBA Service
Station

This application allows your computer to
automatically search for TOSHIBA software
updates or other alerts from TOSHIBA that are
specific to your computer system and its
programs. When enabled, this application
periodically transmits to our servers a limited
amount of system information, which will be
treated in strict accordance with the rules and
regulations as well as applicable data protection
law.

To access this utility, click Start -> All Programs

-> TOSHIBA -> Utilities -> Service Station.

Corel DVD
MovieFactory for
TOSHIBA

Corel DVD MovieFactory for TOSHIBA allows
users to instantly create Blu-ray disc movie, DVD
video or slideshow discs via a user-friendly
wizard interface with specific task oriented
features.

The Labelflash feature is also supported which
allows text and images to be printed on the label
surface of Labelflash compatible media without
using a printer.

Labelflash features cannot be used in models that do not have a DVD
Super Multi drive with Labelflash.

In order to determine if the optical disc drive installed in your computer
supports Labelflash follow the steps as detailed below:

1. Click Start -> All Programs -> DVD MovieFactory for TOSHIBA ->
DVD MovieFactory Launcher to launch DVD MovieFactory.

2. Click Create Disc Label. Corel Label@Once is started.

3. Click the General tab.

4. Choose optical disc drive for Printer.

If the drive name is displayed in Step 4, your computer's optical disc drive
supports Labelflash.

TOSHIBA Bulletin
Board

Bulletin Board is a convenient place to pin things
to visually organize in a fun and creative way.
Simply drag and drop your favorite pictures, files
or notes to pin them on the Board. You can use it
to create thumbnail shortcuts, reminders, to-do
list and so on according to your personal style.

To access this utility, click Start -> All Programs

-> TOSHIBA -> TOSHIBA Bulletin Board.

User’s Manual 3-17

Hardware, Utilities and Options

TOSHIBA ReelTime This application is a graphical history/indexing

tool that enables you to view recently accessed
files in a fun and easy-to-use format. View and
scroll through your history of opened or imported
files via thumbnails in an intuitive user interface.

To access this utility, click Start -> All Programs

-> TOSHIBA -> TOSHIBA ReelTime.

Windows Mobility
Center

Mobility Center is a utility for accessing several
mobile PC settings quickly in one window. A
default maximum of eight tiles are provided by
the operating system, and the additional two tiles
are added to your Mobility Center.

■ Lock Computer :

This can be used to lock your computer
without turning it off. This has the same
function as selecting Lock from the Start
menu (click Start, point to the arrow icon

and then select Lock from

the menu).

■ TOSHIBA Assist :

This can be used to open TOSHIBA Assist if
it is already installed in your computer.

TOSHIBA USB Sleep
and Charge Utility

This utility is able to either enable or disable the
USB Sleep and Charge function.

Shows the positions of USB ports that support
the USB Sleep and Charge function and displays
the battery's remaining capacity.

To start this utility, click Start -> All Programs ->

TOSHIBA -> Utilities -> USB Sleep and
Charge.

TOSHIBA DVD
PLAYER

This software is provided for playback of DVD
Video.

It has an on-screen interface and functions. Click

Start -> All Programs -> TOSHIBA DVD
PLAYER -> TOSHIBA DVD PLAYER.

For details on how to use TOSHIBA DVD
PLAYER, see the help file.

■ Frame dropping, audio skipping or out of synch audio and video may

occur during playback of some DVD Video titles.

■ Make sure to connect the computer's AC adaptor when playing a DVD

Video. Power-saving features may interfere with smooth playback.

User’s Manual 3-18

Optional devices

Optional devices can expand the computer's capabilities and its versatility.
This chapter describes the connection or installation of the following
devices:

To connect optional devices (such as USB device or External monitor) to
the computer, be sure to check the shape and orientation of the connector
before connecting.

Cards/memory

■ Bridge media slot

■ Secure Digital™ (SD) Card (SD memory card, SDHC memory card,

miniSD Card, microSD Card)

■ Memory Stick (Memory Stick, Memory Stick Duo, Memory Stick

PRO, Memory Stick PRO Duo)

■ xD picture card

■ MultiMediaCard

■ Memory expansion

Power devices

■ Battery packs

■ Universal AC Adaptor

■ Battery Charger

Hardware, Utilities and Options

Peripheral devices

■ USB

■ USB FDD Kit

■ eSATA

■ External monitor

■ HDMI

Other

■ Security lock

User’s Manual 3-19

Bridge media slot

Secure Digital (SD) Card

Memory Stick xD picture card MultiMediaCard

(MMC)

microSD card and adaptor

The computer is equipped with a Bridge media slot that can accommodate
some kinds of memory media with various memory capacities so that you
can easily transfer data from devices, such as digital cameras and
Personal Digital Assistants.

Keep foreign objects out of the Bridge media slot. Never allow metal
objects, such as screws, staples and paper clips, to enter the computer or
Keyboard. Foreign metal objects can create a short circuit, which can
cause computer damage and fire, possibly resulting in serious injury.

■ This Bridge media slot supports the following memory media.

■ Secure Digital (SD) Card (SD memory card, SDHC memory card,

miniSD Card, microSD Card)

■ Memory Stick (Memory Stick, Memory Stick Duo, Memory Stick

PRO, Memory Stick PRO Duo)

■ xD picture card

■ MultiMediaCard (MMC™)

■ Please note that an adaptor is required to use miniSD/microSD Card.

■ Please note that an adaptor is required to use Memory Stick

Duo/Memory Stick PRO Duo.

■ Please note that not all memory media have been tested and verified to

work correctly. Therefore, it is not possible to guarantee that all
memory media will operate properly.

■ The slot does not support Magic Gate functions.

Hardware, Utilities and Options

Figure 3-1 Examples of memory media

Memory media

This section provides the important safety precautions in order to handle
your memory media.

User’s Manual 3-20

Hardware, Utilities and Options

Points to note about the SD/SDHC memory card

SD/SDHC memory cards comply with SDMI (Secure Digital Music
Initiative), which is a technology adopted to prevent unlawful copy or
playback of digital music. For this reason, you cannot copy or playback
protected material on another computer or other device, and you may not
reproduce any copyrighted material except for your personal enjoyment.

Below is a simple explanation for distinguishing SD memory cards from
SDHC memory cards.

■ SD and SDHC memory cards appear the same externally.

■ The logo on SD and SDHC memory cards is different, so pay careful

attention to the logo when purchasing.

■ The SD memory card logo is ( ).

■ The SDHC memory card logo is ( ).

■ The maximum capacity of SD memory cards is 2GB. The maximum

capacity of SDHC memory cards is 16GB.

Card Type Capacities

SD 8MB, 16MB, 32MB, 64MB, 128MB, 256MB,

SDHC 4GB, 8GB, 16GB

512MB, 1GB, 2GB

Memory media format

New media cards are formatted according to specific standards. If you wish
to reformat a media card, be sure to do so with a device that uses media
cards.

Formatting an SD/SDHC memory card

If you reformat an SD/SDHC memory card, be sure to reformat it with a
device such as digital camera or digital audio player that uses the
SD/SDHC memory cards, not with the format command provided within
Windows.

Should you need to format all areas of the memory card, including the
protected area, you will need to obtain an appropriate application that
applies the copy protection system.

Media care

Observe the following precautions when handling the card.

Card care

■ Do not twist or bend cards.

■ Do not expose cards to liquids or store in humid areas or lay media

close to containers of liquid.

User’s Manual 3-21

Hardware, Utilities and Options

■ Do not touch the metal part of a card or expose it to liquids or let it get

dirty.

■ After using card, return it to its case.

■ The card is designed so that it can be inserted only one way. Do not try

to force the card into the slot.

■ Do not leave a card partially inserted in the slot. Press the card until you

hear it click into place.

Memory card care

■ Set the write-protect switch to the lock position, if you do not want to

record data.

■ Memory cards have a limited lifespan, so it is important to backup

important data.

■ Do not write to a card if the battery power is low. Low power could affect

writing accuracy.

■ Do not remove a card while read/write is in progress.

For more details on using memory cards, see manuals accompanying the
cards.

About the write-protect

The following memory media have a function for protect.

■ SD Card (SD memory card, SDHC memory card)

■ Memory Stick (Memory Stick, Memory Stick Duo, Memory Stick PRO,

Memory Stick PRO Duo)

■ MultiMediaCard (MMC)

Set the write-protect switch to the lock position, if you do not want to record
data.

Inserting a memory media

The following instructions apply to all types of supported media devices. To
insert a memory media, follow the steps as detailed below:

1. Turn the memory media so that the contacts (metal areas) are face
down.

2. Insert the memory media into the Bridge media slot in the front of the
computer.

3. Press the memory media gently to ensure a firm connection is made.

User’s Manual 3-22

Hardware, Utilities and Options

1

2

1

2

1. Bridge media slot

Figure 3-2 Inserting a memory media

2. Memory media

■ Make sure memory media is oriented properly before you insert it. If

you insert the media in wrong direction, you may not be able to remove
it.

■ When inserting memory media, do not touch the metal contacts. You

could expose the storage area to static electricity, which can destroy
data.

■ Do not turn the computer off or switch to Sleep Mode or Hibernation

Mode while files are being copied - doing so may cause data to be lost.

Removing a memory media

The following instructions apply to all types of supported media devices. To
remove a memory media, follow the steps as detailed below:

1. Open the Safely Remove Hardware icon on the Windows Taskbar.

2. Point to memory media and click the left Touch Pad control button.

3. Press the memory media to partially extend it out of the computer.

4. Grasp the media and remove it.

1. Bridge media slot

Figure 3-3 Removing memory media

2. Memory media

Press gently until the cover clicks into place.

User’s Manual 3-23

Hardware, Utilities and Options

■ Make sure the Bridge Media slot indicator is out before you remove

the memory media or turn off the computer’s power. If you remove the
memory media or turn off the power while the computer is accessing
the memory media, you may lose data or damage the media.

■ Do not remove the memory media while the computer is in Sleep or

Hibernation Mode. The computer could become unstable or data in the
memory media could be lost.

■ Do not remove only the miniSD/microSD Card while leaving the

adaptor in the Bridge Media slot.

Additional memory module

You can install additional memory into the computer in order to increase the
amount of system memory that is available. This section describes how to
install and remove optional memory modules.

■ You should place a mat beneath the computer in order to prevent the

computer's lid from becoming scratched or damaged when you are
installing/replacing the memory module. In this instance you should
avoid mats that are made of materials that hold or generate static
electricity.

■ When installing or removing a memory module, you must ensure that

you do not touch any other internal areas of the computer.

■ Insert the two memory modules into Slot A and Slot B respectively. The

computer will operate in dual channel mode.
You can access the inserted memory modules efficiently in dual
channel.

■ Use only memory modules approved by TOSHIBA.

■ Do not try to install or remove a memory module under the following

conditions.
a. The computer is turned on.
b. The computer was shut down in either Sleep or Hibernation Mode.
c. Wake-up on LAN is enabled.

■ Be careful not to let screws or other foreign matter fall into the

computer. It could cause malfunction or electric shock.

■ Additional memory module is a precision electronic component that

may be fatally damaged by static electricity. Since the human body can
carry static electricity, it is important that you discharge yourself before
touching or installing any additional memory modules. To discharge
your body’s static electricity, simply touch any metal close to you with
bare hands.

User’s Manual 3-24

Hardware, Utilities and Options

1

2

Point to note about memory module error

If you install a memory module that is not compatible with the computer, the
Power indicator will flashes (on for 0.5 seconds, off for 0.5 seconds) in the
following ways;

■ If there is an error in only Slot A: repeatedly flashes orange twice, then

green or white.

■ If there is an error in only Slot B: repeatedly flashes orange, then green

or white twice.

■ If there are errors in both Slot A and Slot B: repeatedly flashes orange

twice, then green or white twice.

In all instances you should shut down the computer and remove the
incompatible module(s).

Use a point size 0 Phillips screwdriver to remove and fasten the screws ­the use of an incorrect screwdriver can damage the screw heads.

Installing a memory module

The computer contains slots for two memory modules, one positioned
immediately over the other - the procedures are the same for installing
either module.

1. Shut down the computer - make sure the Power indicator is off (refer to
the Turning off the power section in Chapter 1, Getting Started if
required).

2. Remove the AC adaptor and all cables and peripherals connected to
the computer.

3. Close the display panel.

4. Turn the computer upside down and remove the battery pack (refer to

Replacing the battery pack section in Chapter 6, Power and Power-Up

Modes, if required).

5. Loosen the screw securing the memory module cover in place - please
note that this screw is attached to the cover in order to prevent it from
being lost.

6. Slide your fingernail or a thin object under the cover and lift it off.

1. Screw 2. Memory module cover

Figure 3-4 Removing the memory module cover

User’s Manual 3-25

Hardware, Utilities and Options

1

2

7. Align the notch of the memory module with that of the memory module
slot and gently insert the module into the slot at about a 45 degree
angle before holding it down until the latches on either side snap into
place.

1. Slot A 2. Slot B

Figure 3-5 Seating the memory module

■ Slot A is reserved for the first memory module. Use slot B for expansion

memory modules. If only one module is installed, use slot A.

■ When inserting or removing memory modules, make sure to use the

correct slot (A or B). On this computer the lower slot is slot A.

■ Align the grooves along the edges of the memory module with the

locking tabs on the connector and insert the memory module into the
connector firmly - if you find it difficult to install the memory module,
gently prise the locking tabs outwards using the tip of your finger.
Please also ensure that you hold the memory module along its left and
right hand edges - the edges with the grooves in.

■ Never allow metal objects, such as screws, staples and paper clips, to

enter the computer or keyboard. Foreign metal objects can create a
short circuit, which can cause computer damage and fire, possibly
resulting in serious injury.

■ Do not touch the connectors on the memory module or on the

computer. Debris on the connectors may cause memory access
problems.

User’s Manual 3-26

Hardware, Utilities and Options

1

2

8. Seat the memory module cover in place and secure it with one screw.

Take care to ensure that the memory module cover is firmly closed.

1. Screw 2. Memory module cover

Figure 3-6 Seating the memory module cover

9. Install the battery pack - refer to Replacing the battery pack section in
Chapter 6, Power and Power-Up Modes, if required.

10. Turn your computer over.

11. Turn the computer on and make sure the added memory is recognized ­to confirmed it, click Start -> Control Panel -> System and Security ­> System.

Removing a memory module

The slot A is reserved for main memory. Use the slot B for expanded
memory. If only one card is installed, use the slot A.

To remove the memory module, follow the steps as detailed below:

1. Shut down the computer - make sure the Power indicator is off (refer to
the Turning off the power section in Chapter 1, Getting Started if
required).

2. Remove the AC adaptor and all cables and peripherals connected to
the computer.

3. Close the display panel.

4. Turn the computer upside down and remove the battery pack (refer to

Replacing the battery pack section in Chapter 6, Power and Power-Up

Modes, if required).

5. Loosen the screw securing the memory module cover in place - please
note that this screw is attached to the cover in order to prevent it from
being lost.

6. Slide your fingernail or a thin object under the cover and lift it off.

7. Push the latches away from the module in order to release it - a spring
will force one end of the module up at an angle.

User’s Manual 3-27

Hardware, Utilities and Options

1

2

3

8. Grasp the memory module by its edges and remove it from the
computer.

■ If you use the computer for a long time, the memory modules and the

circuits locating close to the memory modules will become hot. In this
case, let them cool to room temperature before you replace them.Or
you will get burnt if you touch any of them.

■ Do not touch the connectors on the memory module or on the

computer. Debris on the connectors may cause memory access
problems.

1. Slot A 3. Latches

2. Slot B

Figure 3-7 Removing the memory module

9. Seat the memory module cover in place and secure it with one screw.

Take care to ensure that the memory module cover is firmly closed.

10. Install the battery pack - refer to Replacing the battery pack section in
Chapter 6, Power and Power-Up Modes, if required.

11. Turn your computer over.

Battery Packs

You can increase the portability of the computer with additional battery
packs so that, if you're away from an AC power source and your battery
runs low, you can replace it with a freshly charged battery. Please refer to
Chapter 6, Power and Power-Up Modes for further information.

Universal AC Adaptor

If you frequently use your computer at more than one site, it may be
convenient to purchase an additional AC adaptor to be kept at each site in
order to remove the need to always carry the adaptor with you.

User’s Manual 3-28

Hardware, Utilities and Options

1

2

3

4

Battery Charger

The battery charger provides a convenient way to charge up to two Lithium
Ion battery packs without requiring the use of your computer.

USB

The computer is equipped with the Universal Serial Bus ports that can
accommodate some kinds of devices

These ports comply with the USB 2.0 standard.

USB FDD Kit

The USB floppy diskette drive accommodates either a 1.44MB or 720KB a
3 2/1" floppy diskette and connects to one of the computer's USB ports.

The USB floppy diskette drive is available only as an option.

1. USB connector 3. Floppy diskette slot

2. Disk-In-Use Indicator 4. Eject button

Figure 3-8 USB floppy diskette drive

USB connector Insert this connector into one of the free USB

ports of your computer.

Disk-In-Use
Indicator

This indicator glows when the floppy diskette is
being accessed.

Floppy diskette slot Insert a floppy diskette into this slot.

Eject button When a floppy diskette is fully seated in the drive,

the eject button will pop out. In order to remove
the diskette, push the eject button in order to
cause it to partially pop out of the drive and then
remove it.

User’s Manual 3-29

Hardware, Utilities and Options

1

2

Check the Disk-In-Use indicator when you use the floppy diskette drive.
Do not press the eject button or turn off the computer while the light is
glowing. Doing so could destroy data and damage the floppy diskette or
the drive.

In use, the following should be noted regarding the operation of the USB
floppy diskette drive:

■ The drive should be placed on a flat, horizontal surface.

■ Do not set the drive on an incline greater than 20° while it is operating.

■ Do not place anything on top of the drive.

Connecting the USB floppy diskette drive

To connect the drive, plug the floppy diskette drive's USB connector into a
computer's free USB ports.

Make sure the connector is properly aligned with the socket. Do not try to
force the connection, doing so can damage the connecting pins.

1. USB port 2. USB connector

Figure 3-9 Connecting the USB floppy diskette drive

If you connect the USB floppy diskette drive after the computer has already
been turned on, it will take about ten seconds for it to be recognized by the
computer. Do not attempt to disconnect and reconnect the drive before this
period has elapsed.

User’s Manual 3-30

Hardware, Utilities and Options

1

2

Disconnecting the USB floppy diskette drive

When you have finished using the USB floppy diskette drive, you can follow
the procedures below in order to disconnect it:

1. Wait for the Disk-In-Use Indicator light to go out to make sure all floppy
diskette activity has stopped.

If you disconnect the USB floppy diskette drive or turn off the power while
the computer is accessing the drive you may lose data or damage the
floppy diskette or the drive.

2. Click the Safely Remove Hardware icon on the Windows taskbar.

3. Click the USB floppy diskette drive device that you want to remove.

4. Carefully pull the floppy diskette drive's USB connector out from within
the computer's USB port.

eSATA (External Serial ATA)

An device corresponding to eSATA function can be connected to the
eSATA/USB combo port on the computer.

Connecting the eSATA device

To connect an eSATA device, follow the steps as detailed below:

1. Connect an eSATA cable to the eSATA/USB combo port.

Make sure the connector is properly aligned with the socket.
Do not try to force the connection, doing so can damage the connecting

pins.

1. eSATA/USB combo port 2. eSATA cable

Figure 3-10 Connecting an eSATA cable to the eSATA/USB combo port

User’s Manual 3-31

Hardware, Utilities and Options

1

2

■ A connected eSATA device may not be recognized if it is connected to

the computer's eSATA/USB combo port while the computer is in Sleep
Mode or Hibernation Mode. If this occurs, disconnect the eSATA device
and then reconnect the device while the computer is turned on.

■ If you connect an eSATA device after the computer has already been

turned on, it will take about ten seconds for it to be recognized by the
computer.
Do not attempt to disconnect and reconnect the drive before this period
has elapsed.

Disconnecting an eSATA device

When you have finished using an eSATA device, you can follow the
procedures below in order to disconnect it:

1. Wait for the indicator light of an eSATA device to go out to make sure all
activity has stopped.

If you disconnect an eSATA device or turn off the power while the
computer is accessing the drive you may lose data or damage an eSATA
device or the drive.

2. Click the Safely Remove Hardware icon on the Windows Taskbar.

3. Click an eSATA device that you want to remove.

4. Carefully pull an eSATA device's eSATA/USB combo connector out
from within the computer's eSATA/USB combo port.

External monitor

An external analog monitor can be connected to the external monitor port
on the computer. To connect a monitor, follow the steps as detailed below:

1. Turn the computer's power off.

2. Connect the monitor cable to the external monitor port.

1. External monitor port

Figure 3-11 Connecting the monitor cable to the external monitor port

3. Turn the external monitor’s power on.

4. Turn the computer's power on.

User’s Manual 3-32

2. Monitor cable

Hardware, Utilities and Options

1

2

When you turn on the power, the computer will automatically recognize the
monitor and determine whether it is a color or monochrome device. In the
event that you find that there are issues getting an image displayed on the
correct monitor, you should consider using the FN + F5 hot key to change
the display settings (if you then disconnect the external monitor before you
turn the computer's power off, be sure to press FN + F5 hot key again to
switch to the internal display).

Please refer to Chapter 5, The Keyboard, for further details on using hot
keys to change the display setting.

■ Do not disconnect the external monitor while in Sleep or Hibernation

Mode. Turn off the computer before disconnecting the external monitor.

■ When displaying desktop at external analog monitor, desktop is

sometimes displayed on the center of the monitor with black bars
around desktop (with small size). At that time, please read the manual
of the monitor and set the display mode which is supporting at the
monitor. Then it will be displayed with suitable size with correct aspect
ratio.

HDMI

A HDMI monitor can be connected to the HDMI out port on the computer.
To connect monitor, follow the steps as detailed below:

As the port operation of all HDMI (High-Definition Multimedia Interface)
monitors have not been confirmed, some HDMI monitors may not function
properly.

Connecting the HDMI out port

1. Plug one end of the HDMI cable into the HDMI out port of the HDMI
device.

1. HDMI out port

Figure 3-12 Connecting the HDMI out port

2. Plug the other end of the HDMI cable into the HDMI out port on your
computer.

When connecting or disconnecting an HDMI device to or from the
computer, only do so when the computer is turned on or when the
computer is completely turned off. Do not do so when the computer is in
Sleep Mode or Hibernation Mode.

User’s Manual 3-33

2. HDMI cable

Hardware, Utilities and Options

■ When you connect a television or external monitor to the HDMI port

and the display output device is set to HDMI.
When you unplug the HDMI cable and re-plug it in please wait at least

5 seconds before you replug the HDMI cable again.

■ When you connect a television or external monitor to the HDMI port

and you connect the television, external monitor or external sound
device to another port.

When you change the display output or Unplug/re-plug the HDMI
cable.

The sound output device and the display output device maybe changed
automatically by the system.

Settings for display video on HDMI

To view video on the HDMI device, be sure to configure the following
settings otherwise you may find that nothing is displayed.

■ Be sure to use the FN + F5 HotKey to select the display device before

starting to play video. Do not change the display device while playing
video.

■ Do not change the display device under the following conditions.

■ While data is being read or written.

■ While communication is being carried out.

Select HD Format

To select the display mode, follow the steps as detailed below:

1. Click Start and click Control Panel.

2. Click Appearance and Personalization.

3. Click Display.

4. Click Change display settings.

5. Click Advanced settings.

6. Click List All Modes.

7. Select the one of the below selection at "List All Modes".

Display mode at "List All Modes" HD Format

1920 by 1080, True Color (32bit), 60Herts 1080p

1920 by 1080, True Color (32bit), 30Herts
(Interlaced)

1280 by 720, True Color (32bit), 60Herts 720p

720 by 576, True Color (32bit), 50Herts 576p

720 by 480, True Color (32bit), 60Herts 480p

User’s Manual 3-34

1080i

Hardware, Utilities and Options

The above display mode is a typical HDMI display mode. The selectable
display modes will vary for different HDMI monitors.

REGZA Link (PC Control)

HDMI out port can connect with Type A connector HDMI cable.
One HDMI cable can send and receive video, audio and control signals.
HDMI-CEC (Consumer Electronics Control) is a standard in the CE

Industry which allows devices to work together over an HDMI cable.
By connecting a TV which supports HDMI Control to this port, the remote

control for the connected TV can be used to operate some of the computer
functions.

Some models are supported with the REGZA Link (PC Control).

Using REGZA Link (PC Control)

Toshiba notebooks with REGZA Link (PC Control) include a Toshiba utility
dedicated to take advantage of its capabilities which can allow you to:

■ Use the TV remote control to output the computer screen onto the TV

screen.

■ Use the TV remote control to launch, operate and close applications on

your computer.

■ Turn on the TV when the HDMI output is selected using the Fn + F5

key.

■ Switch the video output (HDMI or LCD) when executing certain desktop

icons.

■ Enable/Disable the REGZA Link (PC Control) function on the computer.

Security lock

A security locks enable you to anchor your computer a desk or other heavy
object in order to help prevent unauthorized removal or theft. The computer
has a security lock slot on its back side into which you can attach one end
of the security cable, while the other end attaches to a desk or similar
object. The methods used for attaching security cables differ from product
to product. Please refer to the instructions for the product you are using for
more information.

Connecting the security lock

In order to connect a security cable to the computer, follow the steps as
detailed below:

1. Turn the computer so its back side faces you.

2. Align the security cable with the 'lock hole' and secure it in place.

User’s Manual 3-35

1. Security lock slot

1

Optional accessories

You are able to add a number of options and accessories in order to make
your computer even more powerful and convenient to use. For reference,
the following list details some of the items that are available from your
reseller or TOSHIBA dealer:

Hardware, Utilities and Options

Figure 3-13 Security lock

DDR3-1066 Memory
Kit

A 1GB, 2GB or 4GB memory module (DDR3-

1066) can easily be installed in the computer.

Battery Pack An additional battery pack can be purchased for

use as either a spare or replacement. Please
refer to Chapter 6, Power and Power-Up Modes
for further information.

Universal AC
Adaptor

If you frequently use your computer at more than
one site, it may be convenient to purchase an
additional AC adaptor to be kept at each site in
order to remove the need to always carry the
adaptor with you.

USB FDD Kit The USB floppy diskette drive accommodates

either a 1.44MB or 720KB floppy diskette through
connection to one of the computer's USB ports.
In use, please be aware that, while you cannot
format 720KB floppy diskettes under Windows 7,
you are able to read and write to diskettes that
have already been formatted.

Battery Charger The optional battery charger allows you to

charge extra battery packs outside of having to
use the computer.

User’s Manual 3-36

Operating Basics

1

2

3

This chapter describes the basic operations of your computer, highlights
the precautions that should be taken when using it.

Using the Touch Pad

To use the Touch Pad, simply touch and move your fingertip across it in the
direction you want the on-screen pointer to go.

Chapter 4

1. Touch Pad On/Off button

2. Touch Pad

Figure 4-1 Touch Pad and Touch Pad control buttons

Press Touch Pad On/Off button could enable or disable the Touch Pad
function. The two buttons below the Touch Pad are used like the buttons on
a standard mouse - press the left button to select a menu item or to
manipulate text or graphics designated by the pointer, and press the right
button to display a menu or other function depending on the software you
are using.

User’s Manual 4-1

3. Touch Pad control buttons

You can also tap the Touch Pad to perform functions similar to those of the
left button on a standard mouse.

AV Controller

The following functions are available in this computer for operating the
Media Center.

This section describes an overview of each function. Please refer to the
Chapter 8, AV functions for more information.

■ Front operation panel

■ Remote controller

Front operation panel

The Front operation panel is located above the keyboard.
AV related functions, such as CD/DVD, Play/Pause, Stop, Previous, Next,

Mute, Illumination On/Off, Camera and DOLBY are available.

Operating Basics

Click: Tap on ce
Double-click: Tap twice
Drag and drop: Tap to select the item(s) you want to move, leave your

finger on the Touch Pad after the second tap and then move the item(s)
to their new destination.

Remote controller

It can operate AV related functions. Some models are provided with a
remote controller.

Web Camera

Some models are equipped with Web Camera, which is a device that
allows you to record video or take photographs with your computer. You
can use it for video chatting or video conferences using a communication
tool such as Windows Live Messenger. TOSHIBA Web Camera
Application will help you to add various video effects to your video or

photograph. It enables the transmission of video and use of video chat via
the internet using specialized applications.

The effective pixel count for this web camera is 1.0 million (maximum
photograph size: 1280x800 pixels) or 0.3 million.

Please refer to the TOSHIBA Web Camera Application Help for details.

User’s Manual 4-2

Operating Basics

1

2

1. Web Camera LED

Figure 4-2 Web Camera

2. Web Camera

■ Do not point the web camera directly at the sun.

■ Do not touch or press strongly on the web camera lens. Doing so may

reduce image quality. Use an eyeglass cleaner (cleaning cloth) or other
soft cloth to clean the lens if it becomes dirty.

■ Setting the [Size] to more than "800x600" will cause a larger amount of

data to be written to the hard disk drive and may interfere with smooth
recording.

■ When recording in dimly lit environments, select "Night Mode" which

allows for brighter images with less noise.

User’s Manual 4-3

Using the TOSHIBA Face Recognition

TOSHIBA Face Recognition uses a face verification library to verify the
face data of users when they log in to Windows. The user can thus avoid
having to enter a password or the like, which makes the login process
easier.

■ TOSHIBA Face Recognition does not guarantee the correct

identification of a user. Changes to the likeness of a registrant, such as
hair style changes, wearing a cap, or wearing glasses may effect the
recognition rates when such changes occur after the registrant had
registered.

■ TOSHIBA Face Recognition may incorrectly recognize faces that are

similar to a registrant.

■ For high security purposes, TOSHIBA Face Recognition is not a

suitable substitute for Windows passwords. When security is a high
priority, use your established Windows passwords to log in.

■ Bright background light and/or shadows may prevent a registrant from

being recognized correctly. In that case, log in using your Windows
password. If recognition of a registrant fails repeatedly, refer to your
computer documentation to learn ways to improve recognition
performance.

■ TOSHIBA Face Recognition records face data in a log when face

recognition fails. When transferring ownership or disposing of your
computer, please uninstall the application or delete all the logs created
by the application. For details on how to do this, see help file.

■ TOSHIBA Face Recognition can be used only in Windows 7.

Operating Basics

Disclaimer

Toshiba does not guarantee that the face recognition utility technology will
be completely secure or error-free. Toshiba does not guarantee that the
face recognition utility will accurately screen out unauthorized users at all
times. Toshiba is not liable for any failure or damage that might arise out of
the use of the face recognition software or utility.

TOSHIBA, ITS AFFILIATES AND SUPPLIERS SHALL HAVE NO
RESPONSIBILITY FOR DAMAGE TO OR LOSS OF ANY BUSINESS,
PROFITS, PROGRAMS, DATA, NETWORK SYSTEMS OR REMOVABLE
STORAGE MEDIA ARISING OUT OF OR RESULTING FROM THE USE
OF THE PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY
THEREOF.

How to register the Face Recognition Data

Take a picture for facial verification purposes, and register the data needed
when you log in. To register the data needed when you log in, follow the
steps as described below:

1. To launch this utility, click Start -> All Programs -> TOSHIBA ->
Utilities -> Face Recognition.

User’s Manual 4-4

Operating Basics

■ The Registration screen is displayed for a logged-in user whose

face has not been registered.

■ The Management screen is displayed for a logged-in user whose

face has already been registered.

2. Click Run as administrator in lower left of the Management screen,
and then click the Register button. The Registration screen is
displayed.

■ If you wish to practice, click the Next button in the Registration

screen.

■ If you do not wish to practice, click the Skip button in the

Registration screen.

3. Click the Next button to start the guide. Follow the guide to practice.

■ Click the Back button to practice the guide once more.

4. Click the Next button to start image-capturing process.
Adjust the position of your face so that it fits within the face-shaped
frame.

5. Once your face has been positioned properly, the recording will
commence.
Start moving your neck very slightly to the left and right, and then move
your neck down and up.

6. Registration will end after you have repeatedly moved your neck left,
right, down and up.
When the register succeeds, below message will be displayed on the
screen:
" Registration successful. Now we’ll do the
verification test. Click the Next button.".
Click the Next button to perform the verification test.

7. Perform the verification test. Face the screen as you do when you
register.

■ If verification fails, click the Back button and re-register. Please refer

to step 6 from step 4.

8. If verification is successful, click the Next button and register an
account.

9. Register the account.
Fill in all the fields.

10. The Management screen is displayed.
The registered account name will be displayed. Clicking on it will cause
the captured image of your face to be displayed on the left.

User’s Manual 4-5

How to Delete the Face Recognition Data

Delete image data, account information, and personal record data created
during registration. To delete the Face Recognition Data, follow the steps
as described below:

1. To launch this utility, click Start -> All Programs -> TOSHIBA ->
Utilities -> Face Recognition.
The Management screen is displayed.

2. Select a user which you want to delete in the Management screen.

3. Click the Delete button. "You are about to delete the user
data. Would you like to continue?" will be displayed on the
screen.

■ If you do not want the data to be deleted, click the No button and

you will then be returned to the Management screen.

■ Clicking the Yes button will remove the selected user from the

Management screen.

How to launch the help file

For further information on this utility, please refer to help file.

■ To launch the help file, click Start -> All Programs -> TOSHIBA ->

Utilities -> Face Recognition Help.

Windows Logon via TOSHIBA Face Recognition

This section explains how to login to Windows with TOSHIBA Face
Recognition. Two authentication modes are provided.

■ AUTO Mode Login screen : If the face authentication tile is selected by

default, you can log in without using the keyboard or mouse.

■ 1:1 Mode Login screen : This mode is essentially the same as AUTO

mode, but the Select Account screen will appear before the Display
Captured Image screen, and you will need to select the user account
to be authenticated in order to start the authentication process.

Operating Basics

AUTO Mode Login screen

1. Turn on the computer.

2. The Select Tiles screen will be displayed.

3. Select Start face recognition ().

4. "Please face the camera" will be displayed.

5. Verification will be performed. If the authentication is successful, the
image data taken in step 4 will be faded in and placed over one another.

■ If an error occurs during authentication, you will be returned to the

Select Tiles screen.

6. The Windows Welcome screen will be displayed, and will be logged in
automatically to Windows.

User’s Manual 4-6

1:1 Mode Login screen

1. Turn on the computer.

2. The Select Tiles screen will be displayed.

3. Select Start face recognition ().

4. The Select Account screen will be displayed.

5. Select the account, and click the arrow button.

6. "Please face the camera" will be displayed.

7. Verification will be performed. If the authentication is successful, the
image data taken in step 6 will be faded in and placed over one another.

■ If an error occurs during authentication, you will be returned to the

Select Tiles screen.

8. The Windows Welcome screen will be displayed, and will be logged in
automatically to Windows.

■ If authentication was successful, but an authentication error

subsequently occurred during the login to Windows, you will be
asked to provide your account information.

Using optical disc drives

The full-size drive provides high-performance execution of CD/DVD/BD­based programs. You can run either 12 cm (4.72") or 8 cm (3.15")
CD/DVD/BDs without an adaptor. An ATAPI interface controller is used for
CD/DVD/BD operation. When the computer is accessing a CD/DVD/BD, an
indicator on the drive glows.

Operating Basics

Use the DVD playback application to view DVD-Video discs.

For precautions on writing to CD/DVD/BDs, refer to the Writing

CD/DVD/BDs section.

When the power of the optical disc drive is off, pressing the FN + Tab keys
will turn the power of the optical disc drive on. Furthermore, it is possible to
set it to turn the power of the optical disc drive on and eject the tray at the
same time.

User’s Manual 4-7

Loading discs

1

2

1

1

To load a disc, follow the steps as detailed below:

1. When the computer’s power is on, press the eject button to open the
disc tray slightly. Grasp the disc tray gently and pull until it is fully
opened.

Operating Basics

1. Eject button

2. Disc tray

Figure 4-3 Pressing the eject button and pulling the disc tray open

2. Lay the disc, label side up, in the disc tray.

1. Laser lens (Super Multi Drive model)

1. Laser lens (BD Drive model)

Figure 4-4 Inserting a disc

User’s Manual 4-8

When the disc tray is fully opened, the edge of the computer will extend
slightly over the disc tray. Therefore, you will need to turn the disc at an
angle when you place it in the disc tray. After seating the disc, however,
make sure it lies flat.

■ Do not touch the laser lens or any portion of its surrounding casing as

this could cause misalignment.

■ Prevent foreign objects from entering the drive. Check the surface of

the disc tray, especially the area behind the front edge of the disc tray,
to make sure there are no such objects before closing the drive.

3. Press gently at the center of the disc until you feel it click into place. The
disc should lie below the top of the spindle, flush with the spindle base.

4. Push the center of the disc tray to close it. Press gently until it locks into
place.

If the disc is not seated properly when the disc tray is closed, the disc
might be damaged. Also, the disc tray might not open fully when you press
the eject button.

Removing discs

To remove the disc, follow the steps as detailed below:

Do not press the eject button while the computer is accessing the media
drive. Wait for the optical disc drive indicator to go out before you open the
disc tray. Also, if the disc is spinning when you open the disc tray, wait for it
to stop before you remove it

.

Operating Basics

1. To pop the disc tray partially open, press the eject button. Gently pull
the disc tray out until it is fully opened.

When the disc tray pops open slightly, wait a moment to make sure the
disc has stopped spinning before pulling the disc tray fully open.

User’s Manual 4-9

2. The disc extends slightly over the sides of the disc tray so you can

Slender object about
15mm Diameter 1.0mm

1

2

3

grasp it. Gently lift out the disc.

Figure 4-5 Removing a disc

3. Push the center of the disc tray to close it. Press gently until it locks into
place.

How to remove discs when the disc tray will not open

Pressing the eject button will not open the disc tray when the computer
power is off. If the power is off, you can open the disc tray by inserting a
slender object (about 15 mm) such as a straightened paper clip into the
eject hole near the eject button.

Operating Basics

1. Disc tray LED

2. Eject button

Figure 4-6 Manual release with the eject hole

3. Eject hole

Turn off the power before you use the eject hole. If the disc is spinning
when you open the disc tray, the disc could fly off the spindle and cause
injury.

User’s Manual 4-10

Optical Drive Auto Lock

This function is provided with some models.
This function automatically locks the optical disc drive eject button if the

computer detects any vibration or other shocks while running on the
battery.

This function prevents the disc tray from opening even if the eject button is
pushed unexpectedly.

When the Optical Drive Auto Lock is on, there will be key mark on the
bottom right of the Optical Drive Power icon in the Taskbar.

To enable this function, turn the Optical Drive Power ON.

Setting the Optical Drive Auto Lock

Right click the Optical Drive Power icon in the Taskbar to change the
Optical Drive Auto Lock settings.

Enabling and Disabling Optical Drive Auto Lock

1. Right click on the Optical Drive Power icon on the Taskbar.

2. Click Optical Drive Auto Lock -> Enable or Disable.

Lock Time Settings for Optical Drive Auto Lock

This sets the amount of time required to pass before the optical disc drive
eject button unlocks when the Computer detects vibration or other shock.

1. Right click on the Optical Drive Power icon on the Taskbar.

2. Click Unlock time settings -> 1s or 3s or 5s.

Operating Basics

■ When the Optical Drive Auto Lock is engaged, the FN+Tab key

combination and Eject Buttons on application screens are disabled.

■ Optical Drive Auto Lock is not enabled immediately after the

computer is started, the disc tray is closed, or the optical disc drive is
switched from OFF to ON using the FN+Tab keys.

Writing CD/DVD/BDs

■ Some models in this series are equipped with Writing CD/DVD/BDs

with the BD-R/RE drive.

■ Some models in this series are equipped with Writing CD/DVD with the

DVD Super Multi drive.

You can use the BD-R/RE drive to write data to either CD-R, CD-RW, DVD­R, DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R (Double Layer),
DVD+RW, DVD-RAM, BD-R, BD-R (Dual Layer), BD-RE or BD-RE (Dual
Layer) discs.

User’s Manual 4-11