Toshiba F20 User Manual

Qosmio F20

TOSHIBA

Qosmio F20

Portable Personal Computer

User’s Manual

Copyright

© 2005 by TOSHIBA Corporation. All rights reserved. Under the copyright
laws, this manual cannot be reproduced in any form without the prior
written permission of TOSHIBA. No patent liability is assumed, with respect
to the use of the information contained herein.

TOSHIBA Qosmio F20 Portable Personal Computer User’s Manual

First edition May 2005
Copyright authority for music, movies, computer programs, data bases and

other intellectual property covered by copyright laws belongs to the author
or to the copyright owner. Copyrighted material can be reproduced only for
personal use or use within the home. Any other use beyond that stipulated
above (including conversion to digital format, alteration, transfer of copied
material and distribution on a network) without the permission of the
copyright owner is a violation of copyright or author’s rights and is subject
to civil damages or criminal action. Please comply with copyright laws in
making any reproduction from this manual.

Ownership and copyright of music, video, computer programs, databases,
etc. are protected by the copyright laws. These copyrighted materials may
be copied for private use at home only. If, beyond the limitation above,
you copy (including to transform data formats) or modify these materials,
transfer them or distribute them via the Internet without approval of
copyright owners, you may be subject to claims for compensation for
damage and/or criminal penalties due to infringements of copyrights or
personal rights. Please remember to observe the copyright laws when you
use this product to copy the copyrighted works or perform other actions.

Please note that you may infringe the owner’s rights protected by the
copyright laws if you use the screen mode switching functions (e.g. Wide
mode, Wide Zoom mode, etc.) of this product to display enlarged images/
video at coffee shops or hotels for the purposes of profits or providing these
to the public.

Disclaimer

This manual has been validated and reviewed for accuracy. The
instructions and descriptions it contains are accurate for the TOSHIBA
Qosmio F20 Portable Personal Computer at the time of this manual’s
production. However, succeeding computers and manuals are subject to
change without notice. TOSHIBA assumes no liability for damages incurred
directly or indirectly from errors, omissions or discrepancies between the
computer and the manual. Graphics processor performance may vary
considerably from specifications due to design configuration.

ii User’s Manual

Trademarks

IBM is a registered trademark and IBM PC is a trademark of International
Business Machines Corporation.

Intel, Intel SpeedStep, Pentium, Celeron and Centrino are trademarks or
registered trademarks of Intel Corporation.

Windows and Microsoft are registered trademarks of Microsoft Corporation.
Photo CD is a trademark of Eastman Kodak.
Sonic RecordNow! and Sonic PrimeTime are registered trademarks of

Sonic Solutions.
Memory Stick is a registered trademark and i.LINK is a trademark of Sony

Corporation.
TruSurround XT, WOW XT, SRS and symbol are trademarks of SRS

Labs, Inc.
TruSurround XT, WOW XT, TruBass, SRS 3D and FOCUS technologies

are incorporated under license from SRS Labs, Inc.
InterVideo and WinDVD are registered trademarks of the InterVideo Inc.

WinDVR and WinDVD Creator are trademarks of the InterVideo Inc.
manufactured under license from Dolby Laboratories.

“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
Other trademarks and registered trademarks not listed above may be used

in this manual.

Macrovision License

This product includes copyright protection technology and intellectual
property that are patented in the U.S. and other countries. These patents
are the property of Macrovision Corporation. The use of copyright
protection must be authorized by Macrovision Corporation. It is intended for
home and other restricted-use applications, unless Macrovision
Corporation expressly authorizes otherwise. All forms of reverse
engineering or decompiling are forbidden.

User’s Manual iii

EU Declaration of Conformity

This product is labelled with the CE Mark in accordance with the related
European Directives, notably Electromagnetic Compatibility Directive
89/336/EEC for the notebook and the electronic accessories including the
supplied power adapter, the Radio Equipment and Telecommunications
Terminal Equipment Directive 99/5/EC in case of implemented
telecommunication accessories and the Low Voltage Directive
73/23/EEC for the supplied power adapter.

CE Marking is the responsibility of TOSHIBA EUROPE GmbH,
Hammfelddamm 8, 41460 Neuss, Germany, phone [phone].
For a copy of the related CE Declaration of Conformity please refer to the

following website: http://epps.toshiba-teg.com
This product and the supplied accessories are designed to observe the

related EMC (Electromagnetic Compatibility) and safety standards.
However, TOSHIBA cannot guarantee that this product still observes these
EMC standards if accessories or cables not manufactured / distributed by
TOSHIBA are connected or implemented. To avoid EMC problems in
general, the following advice should be observed:

■ Only CE marked accessories should be connected / implemented.

■ Only best shielded cables should be connected.

iv User’s Manual

Working environment

This product was designed to fulfill the EMC (Electromagnetic Compatibility)
requirements for “residential, commercial and light industry environments”.

The following environments are not approved:

■ Industrial Environments (e.g. enivronments with a mains voltage

380V)

In the following environments the use of this product can be restricted:

■ Medical Environments: This product is not certified as a medical

product according to the Medical Product Directive 93/42/EEC,
but can be used in office areas where the use is not restricted.
Please disable the wireless LAN or Bluetooth hardware in such
areas as long this feature is not official supported by the operator of
the related medical facility.

■ Vehicle Environments: Please read the operator’s manual of the

vehicle manufacturer for further restrictions of use.

■ Aircraft Environments: Please follow the advices of the flight

personnel regarding restrictions of use.

Any consequences resulting from the use of this product in working
environments that are not approved or the use is restricted are not the
responsibility of TOSHIBA Corporation. The consequences of the use of
this product in those working environments may be:

■ Interference with other devices or machines in the nearby

surrounding area

■ Malfunction of or data loss from this product caused by disturbances

generated by other devices or machines in the nearby surrounding
area

Furthermore, for general safety reaons, the use of this product in
environments with explosive atmospheres is not permitted.

User’s Manual v

Modem warning notice

Conformity Statement

The equipment has been approved to [Commission Decision “CTR21”] for
pan-European single terminal connection to the Public Switched Telephone
Network (PSTN).

However, due to differences between the individual PSTNs provided in
different countries/regions the approval does not, of itself, give an
unconditional assurance of successful operation on every PSTN network
termination point.

In the event of problems, you should contact your equipment supplier in the
first instance.

Network Compatibility Statement

This product is designed to work with, and is compatible with the following
networks. It has been tested to and found to conform with the additional
requirements conditional in EG 201 121.

Germany ATAAB AN005,AN006,AN007,AN009,AN010

Greece ATAAB AN005,AN006 and GR01,02,03,04
Portugal ATAAB AN001,005,006,007,011 and

Spain ATAAB AN005,007,012, and ES01
Switzerland ATAAB AN002
All other countries/regions ATAAB AN003,004
Specific switch settings or software setup are required for each network,

please refer to the relevant sections of the user guide for more details.
The hookflash (timed break register recall) function is subject to separate

national type approvals. It has not been tested for conformity to national
type regulations, and no guarantee of successful operation of that specific
function on specific national networks can be given.

and DE03,04,05,08,09,12,14,17

P03,04,08,10

vi User’s Manual

Optical disc drive safety instructions

Be sure to check the international precautions at the end of this section.

Panasonic

DVD-ROM&CD-R/RW UJDA770

■ The DVD-ROM&CD-R/RW drive employs a laser system. To ensure

proper use of this product, please read this instruction manual carefully
and retain for future reference. Should the unit ever require
maintenance, contact an authorized service location.

■ Use of controls, adjustments or the performance of procedures other

than those specified may result in hazardous radiation exposure.

■ To prevent direct exposure to the laser beam, do not try to open the

enclosure.

User’s Manual vii

DVD Super Multi with Double Layer Recording UJ-840

■ The DVD Super Multi drive with Double Layer Recording model

employs a laser system. To ensure proper use of this product, please
read this instruction manual carefully and retain for future reference.
Should the unit ever require maintenance, contact an authorized
service location.

■ Use of controls, adjustments or the performance of procedures other

than those specified may result in hazardous radiation exposure.

■ To prevent direct exposure to the laser beam, do not try to open the

enclosure.

viii User’s Manual

TEAC

DVD-ROM&CD-R/RW DW-224-E

■ The DVD-ROM&CD-R/RW drive employs a laser system.

To ensure proper use of this product, please read this instruction
manual carefully and retain for future reference. Should the unit ever
require maintenance, contact an authorized service location.

■ Use of controls, adjustments or the performance of procedures other

than those specified may result in hazardous radiation exposure.

■ To prevent direct exposure to the laser beam, do not try to open the

enclosure.

C

User’s Manual ix

DVD Super Multi with Double Layer Recording DV-W28EA

■ The DVD Super Multi drive with Double Layer Recording model

employs a laser system. To ensure proper use of this product,
please read this instruction manual carefully and retain for future
reference. Should the unit ever require maintenance, contact an
authorized service location.

■ Use of controls, adjustments or the performance of procedures other

than those specified may result in hazardous radiation exposure.

■ To prevent direct exposure to the laser beam, do not try to open the

enclosure.

x User’s Manual

TSST (TOSHIBA SAMSUNG STORAGE TECHNOLOGY)

DVD-ROM&CD-R/RW TS-L462A

■ The DVD-ROM&CD-R/RW drive employs a laser system.

To ensure proper use of this product, please read this instruction
manual carefully and retain for future reference. Should the unit
ever require maintenance, contact an authorized service location.

■ Use of controls, adjustments or the performance of procedures other

than those specified may result in hazardous radiation exposure.

■ To prevent direct exposure to the laser beam, do not try to open the

enclosure.

User’s Manual xi

DVD Super Multi with Double Layer Recording TS-L632B

■ The DVD Super Multi drive with Double Layer Recording model

employs a laser system. To ensure proper use of this product,
please read this instruction manual carefully and retain for future
reference. Should the unit ever require maintenance, contact an
authorized service location.

■ Use of controls, adjustments or the performance of procedures other

than those specified may result in hazardous radiation exposure.

■ To prevent direct exposure to the laser beam, do not try to open the

enclosure.

xii User’s Manual

International precautions

CLASS 1 LASER PRODUCT
LASERSCHUTZKLASSE 1
PRODUKT
TOEN60825

CAUTION: This appliance contains a
laser system and is classified as a
“CLASS 1 LASER PRODUCT.” To use
this model properly, read the instruction
manual carefully and keep this manual
for your future reference. In case of any
trouble with this model, please contact
your nearest “AUTHORIZED service
station.” To prevent direct exposure to the
laser beam, do not try to open the
enclosure.

VORSICHT: Dieses Gerät enthält ein
Laser-System und ist als
“LASERSCHUTZKLASSE 1 PRODUKT”
klassifiziert. Für den richtigen Gebrauch
dieses Modells lesen Sie bitte die
Bedienungsanleitung sorgfältig durch
und bewahren diese bitte als Referenz
auf. Falls Probleme mit diesem Modell
auftreten, benachrichtigen Sie bitte die
nächste “autorisierte Service-Vertretung”.
Um einen direkten Kontakt mit dem
Laserstrahl zu vermeiden darf das Gerät
nicht geöffnet werden.

ADVERSEL:USYNLIG
LASERSTRÅLING VED
ÅBNING, NÅR
SIKKERHEDSAF-BRYDER

ER UDE AF FUNKTION.
UNDGÅ UDSÆTTSLSE
FOR STRÅLING

ADVARSEL: Denne mærking er anbragt
udvendigt på apparatet og indikerer, at
apparatet arbejder med laserstråler af
klasse 1, hviket betyder, at der anvendes
laserstrlier af svageste klasse, og at man
ikke på apparatets yderside kan bilve
udsat for utilladellg kraftig stråling.

APPARATET BOR KUN ÅBNES AF
FAGFOLK MED SÆRLIGT KENDSKAB
TIL APPARATER MED
LASERSTRÅLER!

Indvendigt i apparatet er anbragt den her
gengivne advarselsmækning, som
advarer imod at foretage sådanne
indgreb i apparatet, at man kan komme til
at udsatte sig for laserstråling.

User’s Manual xiii

OBS! Apparaten innehåller
laserkomponent som avger laserstråining
överstigande gränsen för laserklass 1.

VAROITUS. Suojakoteloa si saa avata.
Laite sisältää laserdiodin, joka lähetää
näkymätöntä silmilie vaarallista
lasersäteilyä.

CAUTION: USE OF CONTROLS OR
ADJUSTMENTS OR PERFORMANCE
OF PROCEDURES OTHER THAN
THOSE SPECIFIED IN THE OWNER’S
MANUAL MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.

VORSICHT: DIE VERWENDUNG VON
ANDEREN STEUERUNGEN ODER
EINSTELLUNGEN ODER DAS
DURCHFÜHREN VON ANDEREN
VORGÄNGEN ALS IN DER
BEDIENUNGSANLEITUNG
BESCHRIEBEN KÖNNEN
GEFÄHRLICHE
STRAHLENEXPOSITIONEN ZUR
FOLGE HABEN.

xiv User’s Manual

Qosmio F20

Table of Contents

General Precautions

The cautions on use of a Qosmio F20 series computer . . . . . . . . . . . . . . . . . . . . . . xx

Preface

Manual contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxiii

Conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxiv

Chapter 1 : Introduction

Equipment checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

Special features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11

Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13

Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16

Chapter 2 : The Grand Tour

Front with the display closed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Left side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Right side. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Back side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

Underside. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

Front with the display open . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8

System indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10

Optical media drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12

AC adaptor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14

Chapter 3 : Getting Started

Setting up your work space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Connecting the AC adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

Opening the display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9

Turning on the power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10

Starting up for the first time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10

Turning off the power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11

Restarting the computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15

Restoring the preinstalled software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15

User’s Manual xv

Chapter 4 : Operating Basics

Using the Touch Pad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1

Using optical media drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2

Writing CDs on DVD-ROM&CD-R/RW drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5

Writing CDs/DVDs on DVD Super Multi drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-7

Media care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-15

TV Tuner. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-16

Sound System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-20

Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-21

Wireless communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-25

LAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-27

Cleaning the computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-28

Moving the computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-28

Heat dispersal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-29

Chapter 5 : The Keyboard

Typewriter keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1

Function keys: F1 … F12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2

Soft keys: Fn key combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2

Hot keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-3

Windows special keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-6

Keypad overlay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-7

Generating ASCII characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-8

Chapter 6 : Power

Power conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1

Power indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2

Battery types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-3

Care and use of the battery pack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-5

Replacing the battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-12

TOSHIBA Password Utility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-13

Starting the computer by password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-14

Power-up modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-15

Panel power on/off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-15

System Auto Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-15

Chapter 7 : HW Setup

Accessing HW Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1

HW Setup window. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1

Configuring the Execute-Disable Bit Capability. . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-7

xvi User’s Manual

Chapter 8 : Using the Remote Controller, Front operation button and

QosmioPlayer

Windows XP Home Edition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

Front operation button function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2

Remote Controller. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4

Using the Remote Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8

Installing/Removing batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10

Watching the TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12

Windows XP Media Center Edition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-17

Front operation button function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-18

Remote Controller. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-21

Using the Remote Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-25

Installing/Removing batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-28

Watching the TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-30

QosmioPlayer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-33

Front operation button function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-33

Remote Controller. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-35

Using the Remote Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-49

Installing/Removing batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-50

Using Toshiba Picture Enhancement Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-53

Chapter 9 : Optional Devices

PC card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2

Bridge media slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3

Memory expansion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-11

Battery Packs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-15

Universal AC Adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-15

Battery Charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-15

Hard disk drive pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-15

USB floppy disk drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-17

External monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-19

TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-19

Displaying movies on a TV or CRT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-21

VIDEO-IN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-22

i.LINK (IEEE1394) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-22

Bluetooth SD Card3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-24

Bluetooth USB Adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-24

Security lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-24

Chapter 10 : Troubleshooting

Problem solving process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1

Hardware and system checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3

Disposing of PC and PC batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-19

TOSHIBA support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-20

User’s Manual xvii

Chapter 11 : Disclaimers

CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-1

Specific Main Memory Disclaimer/Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-2

Battery Life Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-2

HDD Drive Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-3

LCD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-3

Graphics Processor Unit (“GPU”) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-3

Wireless LAN/Atheros . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-3

Non-applicable Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-4

SRS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-4

Copy Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-4

TV Tuner. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-4

Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-4

Qosmio™ Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-4

LCD Brightness and Eye Stain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-4

Safety Use for TV Tuner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-4

Appendix A : Specifications

Physical Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Appendix B : Display Controller and Modes

Display controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1

Video modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1

PowerMizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-10

Appendix C : Wireless LAN

Card Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1

Radio Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1

Supported Frequency Sub-bands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2

Appendix D : AC Power Cord and Connectors

Certification agencies. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-1

Appendix E : Usage Restrictions

Appendix F : If your computer is stolen

Glossary

Index

xviii User’s Manual

Qosmio F20

General Precautions

TOSHIBA computers are designed to optimize safety, minimize strain and
withstand the rigors of portability. However, certain precautions should be
observed to further reduce the risk of personal injury or damage to the
computer.

Be certain to read the general precautions below and to note the cautions
included in the text of the manual.

Stress injury

Carefully read the Instruction Manual for Safety & Comfort. It contains
information on prevention of stress injuries to your hands and wrists than
can be caused by extensive keyboard use. Chapter 3, Getting Started,
also includes information on workspace design, posture and lighting that
can help reduce physical stress.

Heat injury

■ Avoid prolonged physical contact with the computer. If the computer is

used for long periods, its surface can become very warm. While the
temperature will not feel hot to the touch, if you maintain physical
contact with the computer for a long time (if you rest the computer on
your lap, or if you keep your hands on the palm rest, for example) your
skin might suffer low-heat injury.

■ If the computer has been used for a long time, avoid direct contact with

the metal plate supporting the I/O ports. It can become hot.

■ The surface of the AC adaptor can become hot when in use. This

condition does not indicate a malfunction. If you need to transport the
AC adaptor, disconnect it and let it cool before moving it.

■ Do not lay the AC adaptor on a material that is sensitive to heat. The

material could be damaged.

Pressure or impact damage

Do not apply heavy pressure to the computer or subject it to strong impact.
Excessive pressure or impact can cause damage to computer components
or otherwise cause malfunctions.

PC card overheating

Some PC cards can become hot with prolonged use. Overheating of a PC
card can result in errors or instability in the PC card operation. Also be
careful when you remove a PC card that has been used for a long time.

User’s Manual xix

General Precautions

Mobile phone

Use of mobile phones can interfere with the audio system. Computer
operation is not impaired but is recommended that a distance of 30 cm be
maintained between the computer and a mobile phone in use.

The cautions on use of a Qosmio F20 series computer

1. Cleaning of dust accumulated on the cooling vent of the computer.

When you use your computer in a dusty area, dirt and debris may
accumulate on the cooling vents at the under side of your unit. If this
occurs, the accumulated dust can cause insufficient heat dissipation which
may result in the computer shutting down during use. Carefully clean the
dust from the vents using a vacuum cleaner.

2. Cooling vents on the underside and left side of the computer.

Cooling vents

Cooling vents

Cooling vents

Cooling vents

Cooling vents

xx User’s Manual

General Precautions

To prevent possible overheating of the CPU, make sure the cooling fan’s
air intake is not blocked. The fan draws in air by creating a vacuum. If the
fan is blocked, it could cause the CPU to run at a lower performance level
or cause the computer to shut down. Loose items such as notebook and
tissue paper, plastic wrappers, or other similar materials can block the air
intake, preventing air from reaching the CPU. Do not use the computer on
surfaces with objects that can be drawn in by the cooling fan.

User’s Manual xxi

General Precautions

xxii User’s Manual

Qosmio F20

Preface

Congratulations on your purchase of the Qosmio F20 computer. This
powerful notebook computer provides excellent expansion capability,
including multimedia devices, and it is designed to provide years of reliable,
high-performance computing.

This manual tells how to set up and begin using your Qosmio F20
computer. It also provides detailed information on configuring your
computer, basic operations and care, using optional devices and
troubleshooting.

If you are a new user of computers or if you’re new to portable computing,
first read over the Introduction and The Grand Tour chapters to familiarize
yourself with the computer’s features, components and accessory devices.
Then read Getting Started for step-by-step instructions on setting up your
computer.

If you are an experienced computer user, please continue reading the
preface to learn how this manual is organized, then become acquainted
with this manual by browsing through its pages. Be sure to look over the

Special features section of the Introduction, to learn about features that are

uncommon or unique to the computers and carefully read HW Setup.
If you are going to install PC cards or connect external devices such as a

monitor, be sure to read Chapter 9, Optional Devices.

Manual contents

This manual is composed of the following eleven chapters, six appendixes,
a glossary and an index.

Chapter 1, Introduction, is an overview of the computer’s features,
capabilities, and options.

Chapter 2, The Grand Tour, identifies the components of the computer and
briefly explains how they function.

Chapter 3, Getting Started, provides a quick overview of how to begin
operating your computer and gives tips on safety and designing your work
area.

Chapter 4, Operating Basics, This chapter describes the basic operations
of your computer and precautions when using it, as well as the handling of
CD/DVD.

User’s Manual xxiii

Preface

Chapter 5, The Keyboard, describes special keyboard functions including the
keypad overlay and hot keys.

Chapter 6, Power, gives details on the computer’s power resources and
battery save modes.

Chapter 7, HW Setup, explains how to configure the computer using the HW
Setup program.

Chapter 8, Using the Remote Controller, Front operation button and

QosmioPlayer, explains how to use the Remote Controller on Windows XP

Media Center Edition and Windows XP Home Edition models as well as
provides information about QosmioPlayer.

Chapter 9, Optional Devices, describes the optional hardware available.
Chapter 10, Troubleshooting, provides helpful information on how to perform

some diagnostic tests, and suggests courses of action if the computer
doesn’t seem to be working properly.

Chapter 11, Disclaimers, provides disclaimer information related to your
computer.

The Appendixes provide technical information about your computer.
The Glossary defines general computer terminology and includes a list of

acronyms used in the text.
The Index quickly directs you to the information contained in this manual.

Conventions

This manual uses the following formats to describe, identify, and highlight
terms and operating procedures.

Abbreviations

On first appearance, and whenever necessary for clarity, abbreviations are
enclosed in parentheses following their definition. For example: Read Only
Memory (ROM). Acronyms are also defined in the Glossary.

Icons

Icons identify ports, dials, and other parts of your computer. The indicator
panel also uses icons to identify the components it is providing information
on.

Keys

The keyboard keys are used in the text to describe many computer
operations. A distinctive typeface identifies the key top symbols as they
appear on the keyboard. For example, Enter identifies the Enter key.

xxiv User’s Manual

Key operation

Some operations require you to simultaneously use two or more keys. We
identify such operations by the key top symbols separated by a plus sign
(+). For example, Ctrl + C means you must hold down Ctrl and at the same
time press C. If three keys are used, hold down the first two and at the
same time press the third.

Preface

ABC

When procedures require an action such as
clicking an icon or entering text, the icon’s name
or the text you are to type in is represented in the
type face you see to the left.

Display

S

ABC

Names of windows or icons or text generated by
the computer that appear on its display screen
are presented in the type face you see to the left.

Messages

Messages are used in this manual to bring important information to your
attention. Each type of message is identified as shown below.

Pay attention! A caution informs you that improper use of equipment or
failure to follow instructions may cause data loss or damage your
equipment.

Please read. A note is a hint or advice that helps you make best use of
your equipment.

Indicates a potentially hazardous situation, which could result in death or
serious injury, if you do not follow instructions.

User’s Manual xxv

Preface

xxvi User’s Manual

Qosmio F20

Introduction

This chapter provides an equipment checklist, and it identifies the
computer’s features, options and accessories.

Some of the features described in this manual may not function properly if
you use an operating system that was not preinstalled by TOSHIBA.

Equipment checklist

Carefully unpack your computer. Save the box and packing materials for
future use.

Hardware

Check to make sure you have all the following items:

■ Qosmio F20 Portable Personal Computer

■ AC adaptor and power cord (2-pin plug or 3-pin plug)

■ Modular cable (optional)

■ VIDEO-IN cable (Used for connection to VIDEO-IN port. Refer to

chapter 8, Using the Remote Controller, Front operation button and

QosmioPlayer)

■ Remote Controller

■ Remote control receiver (Windows XP Media Center Edition model

only)

■ Infrared transmitter cable (Windows XP Media Center Edition model

only)

■ Antenna adaptor (optional)

Chapter 1

User’s Manual 1-1

Introduction

Software

Microsoft® Windows XP Home Edition

■ The following software is preinstalled:

■ Microsoft® Windows XP Home Edition

■ TOSHIBA Utilities

■ DVD Video Player

■ TOSHIBA Power Saver

■ TOSHIBA ConfigFree

■ TOSHIBA Assist

■ TOSHIBA Controls

■ TOSHIBA PC Diagnostic Tool

■ TOSHIBA Touch and Launch

■ TOSHIBA TouchPad On/Off Utility

■ TOSHIBA Zooming Utility

■ TOSHIBA Picture Enhancement Utility

■ InterVideo WinDVR

■ TOSHIBA SD Memory Card Format

■ TOSHIBA Acoustic Silencer

■ TOSHIBA Virtual Sound

■ TOSHIBA Hotkey Utility for Display Devices

■ TOSHIBA Display Device Change Utility

■ TOSHIBA Password Utility

■ Online manual

■ Product Recovery Media

1-2 User’s Manual

Microsoft® Windows XP Media Center Edition

■ The following software is preinstalled:

®

■ Microsoft

■ TOSHIBA Utilities

■ DVD Video Player

■ TOSHIBA Power Saver

■ TOSHIBA ConfigFree

■ TOSHIBA Assist

■ TOSHIBA Controls

■ TOSHIBA PC Diagnostic Tool

■ TOSHIBA Touch and Launch

■ TOSHIBA TouchPad On/Off Utility

■ TOSHIBA Zooming Utility

■ TOSHIBA Picture Enhancement Utility

■ TOSHIBA SD Memory Card Format

■ TOSHIBA Acoustic Silencer

■ TOSHIBA Virtual Sound

■ TOSHIBA Hotkey Utility for Display Devices

■ TOSHIBA Display Device Change Utility

■ TOSHIBA Password Utility

■ Online manual

■ Product Recovery Media

Windows XP Media Center Edition

Introduction

Documentation

■ Qosmio F20 Portable Personal Computer User’s Manual

■ Instruction Manual for Safety & Comfort

■ Qosmio F20 Quickstart

■ QosmioPlayer Software License Agreement

■ Warranty information

If any of the items are missing or damaged, contact your dealer
immediately.

User’s Manual 1-3

Introduction

Features

The computer uses TOSHIBA’s advanced Large Scale Integration (LSI),
Complementary Metal-Oxide Semiconductor (CMOS) technology
extensively to provide compact size, minimum weight, low power usage,
and high reliability. This computer incorporates the following features and
benefits:

Processor

Built-in

The computer is equipped with an Intel

®

processor.

®

■ Intel

Celeron® M processor, which

incorporates a 1 MB level 2 cache memory.

■ Intel

®

Pentium® M processor, which
incorporates a 2MB level 2 cache memory.
It also supports Enhanced Intel

®

SpeedStepTM

technology.

Some models of the computers carry Intel® Centrino™ technology, which
is based on three separate technologies of Intel

®

Intel

PRO/Wireless Network Connection, and Intel® 915 Chipset Family.

®

Pentium® M processor,

Disclaimer (CPU)

For more information on the Disclaimer regarding CPU, please refer to the
Disclaimers section in Chapter 11.

Memory

Slots 256, 512 or 1,024 MB memory modules can be

installed in the two memory slots for a maximum
of 2,048 MB system memory.

Disclaimer (Specific Main Memory Disclaimer)

For more information on the Disclaimer regarding Specific Main Memory
Disclaimer, please refer to the Disclaimers section in Chapter 11.

1-4 User’s Manual

Introduction

Video RAM There are three different types of graphics

controllers. The Video RAM specifications will
differ depending on the type of graphics
controller used in the computer.

■ Intel internal graphics system model: Part of

system memory is used for Video RAM.
128MB of RAM is provided for Video display.

■ nVIDIA GeForce Go 6200 TurboCache™

model: Part of system memory is used for
Video RAM. Maximum 128 MB of RAM is
provided for video display.

■ nVIDIA GeForce Go 6600 model: 64/128MB

of RAM is provided for Video display.

Power

Battery pack The computer is powered by one rechargeable

lithium-ion battery pack.

Disclaimer (Battery Life)

For more information on the Disclaimer regarding Battery Life, please refer
to the Disclaimers section in Chapter 11.

RTC battery The internal RTC battery backs up the Real Time

Clock and calendar.

AC adaptor The AC adaptor provides power to the system

and recharges the batteries when they are low.
It comes with a detachable power cord. It
encloses 2-pin or 3-pin plug type.

Because it is universal, it can receive a range of
AC voltage from 100 to 240 volts; however, the
output current varies among different models.
Using the wrong model can damage your
computer. Refer to the AC adaptor section in
Chapter 2, The Grand Tour.

User’s Manual 1-5

Introduction

Disks

Hard disk drive Available in four sizes.

■ 40.0 billion bytes (37.26 GB)

■ 60.0 billion bytes (55.88 GB)

■ 80.0 billion bytes (74.52 GB)

■ 100.0 billion bytes (93.16 GB)

Depending on your configuration, your computer
is equipped with either one or two hard disk
drives.

Other hard disk drives may be introduced.

Disclaimer (HDD Drive Capacity)

For more information on the Disclaimer regarding HDD Drive Capacity,
please refer to the Disclaimers section in Chapter 11.

Optical media drive

Computers in this series can be configured with an optical media drive.
The available optical media drives are described below.

DVD-ROM&CD-R/RW
drive

1-6 User’s Manual

Some models are equipped with a full-size,
DVD-ROM&CD-R/RW drive module that lets you
run CD/DVDs without using an adaptor. It reads
DVD-ROMs at maximum 8 speed and CD-ROMs
at maximum 24 speed. It writes CD-R and
CD-RW at maximum 24 speed. This drive
supports the following formats:

■ DVD-ROM

■ DVD-Video

■ CD-DA

■ CD-Text

■ Photo CD™ (single/multi-session)

■ CD-ROM Mode 1, Mode 2

■ CD-ROM XA Mode 2 (Form1, Form2)

■ Enhanced CD (CD-EXTRA)

■ Addressing Method 2

■ CD-R

■ CD-RW

Introduction

DVD Super Multi
drive Double Layer

Some models are equipped with a full-size DVD
Super Multi drive module that lets you record
data to rewritable CD/DVDs as well as run
12cm (4.72") CD/DVDs. It reads DVD-ROMs at
maximum 8 speed and CD-ROMs at maximum
24 speed. It writes CD-R at up to 24 speed,
CD-RW at up to 10 speed, DVD-R and DVD+R at
maximum 8 speed, DVD+R DL at maximum

2.4 speed, DVD-RW and DVD+RW at maximum
4 speed, DVD-RAM at maximum 5 speed. This
drive supports the following formats in addition to
DVD-ROM&CD-R/RW drive.

■ DVD-R

■ DVD-RW

■ DVD-RAM

■ DVD+R

■ DVD+RW

Display

The computer’s LCD panel supports high-resolution video graphics. The
screen can be set at a wide range of viewing angles for maximum comfort
and readability.

Built-in 15.4" TFT screen 32 M colors, with a resolution

of 1280 horizontal × 800 vertical pixels WXGA.

Disclaimer (LCD)

For more information on the Disclaimer regarding LCD, please refer to the
Disclaimers section in Chapter 11.

Graphics controller Graphics controller maximizes display

performance. Refer to Display Controller and

Modes section in Appendix B for more

information.

Disclaimer (Graphics Processor Unit (“GPU”))

For more information on the Disclaimer regarding Graphics Processor Unit
(“GPU”), please refer to the Disclaimers section in Chapter 11.

Keyboard

Built-in

User’s Manual 1-7

85 keys or 86 keys, compatible with IBM
enhanced keyboard, embedded numeric overlay,

dedicated cursor control, and keys.
Refer to Chapter 5, The Keyboard, for details.

®

Introduction

Pointing Device

Built-in Touch Pad A Touch Pad and control buttons in the palm rest

enable control of the on-screen pointer and
scrolling of windows.

Ports

External monitor Analog VGA port supports VESA DDC2B

Universal Serial Bus
(USB 2.0)

i.LINK™ (IEEE1394) This port enables high-speed data transfer

compatible functions.
The computer has Universal Serial Bus ports that

comply with the USB 2.0 standard, which
enables data transfer speeds 40 times faster
than the USB 1.1 standard (The ports also
support USB 1.1).

directly from external devices such as digital
video cameras.

Slots

PC card The PC card slot accommodates a 5 mm Type II

card.

Bridge media This slot lets you insert SD card, Memory Stick

(Pro), xD picture card and MultiMediaCard. Refer
to Chapter 9, Optional Devices.

Multimedia

Sound system Windows sound system compatible sound

system provides internal speakers as well as
jacks for an external microphone and
headphones.

TV antenna port Connect the antenna adaptor to this port to watch

TV programs on your computer or record them.

S-Video out port This S-Video out port lets you transfer NTSC or

PAL data to external devices. Refer to TV section
in Chapter 9, Optional Devices.

1-8 User’s Manual

Introduction

VIDEO-IN port The port is used differently depending on the

type of OS used in the computer.
Windows XP Home Edition model: With the

bundled VIDEO-IN cable, external devices such
as TV, video recorders, etc., can be connected to
the computer and WinDVR and WinDVD Creator
2 Platinum can be used to edit or view the inputs.

Media Center Edition model: With the bundled
VIDEO-IN cable, the CATV or satellite set top
boxes can be connected to the computer to view
the channels. The video cannot be extracted for
editing as in the Windows XP Home Edition model.

Please refer to Chapter 8, Using the Remote

Controller, Front operation button and
QosmioPlayer for details on how to connect the

computer with the VIDEO-IN cable.

Headphone (S/PDIF)
jack

This jack lets you connect digital speakers or a
stereo headphones (16 ohm minimum). When
you connect a digital speaker or headphones,
the internal speakers are automatically disabled.

This jack can be used also as S/PDIF jack and
enables connection of optical digital
correspondence apparatus.

Microphone jack A 3.5 mm mini microphone jack enables

connection of a three-conductor mini jack for
monaural microphone input.

Built-in TV Tuner Windows XP Home Edition:

Use the WinDVR program to display TV
programs on the built-in LCD and record them.
It is also possible to edit recorded programs and
save them on a DVD.

Windows XP Media Center Edition:
Start Media Center and select My TV.

Infrared receiver
window

This is a sensor window that receives signals
from the Remote Controller which is provided
with your computer.

Not supported by Windows XP Media Center
Edition.

Remote Controller Use this device to navigate when watching TV or

playing CDs/DVDs. Its type and functions may
depend on the model of your computer.

Remote control
receiver

This is a sensor device that receives signals from
the Remote Controller which is provided with
your computer. This Remote control receiver is
supported only by Windows XP Media Center
Edition.

User’s Manual 1-9

Introduction

Communications

Modem An internal modem provides capability for data

and fax communication. It supports V.90 (V.92).
The speed of data transfer and fax depends on
analog telephone line conditions. It has a modem
jack for connecting to a telephone line. Both of
V.90 and V.92 are supported only in USA,
Canada, UK, France, Germany and Australia.
Only V.90 is available in other regions.

LAN The computer has built-in support for Ethernet

LAN (10 megabits per second, 10BASE-T) and
Fast Ethernet LAN (100 megabits per second,
100BASE-TX).

Wireless LAN Some computers in this series are equipped with

a Wireless LAN mini-PCI card that is compatible
with other LAN systems based on Direct
Sequence Spread Spectrum/Orthogonal
Frequency Division Multiplexing radio technology
that complies with the IEEE 802.11 Standard
(Revision A, B or G), and Turbo Mode.

■ Theoretical maximum speed: 54 Mbps

(IEEE802.11a, 802.11g)

■ Theoretical maximum speed: 11 Mbps

(IEEE802.11b)

■ Frequency Channel Selection

(5 GHz: Revision A / 2.4 GHz: Revision B/G)

■ Roaming over multiple channels

■ Card Power Management

■ Wired Equivalent Privacy (WEP) data

encryption, based on 152 bit encryption
algorithm (Atheros module type).

■ Wired Equivalent Privacy (WEP) data

encryption, based on 128 bit encryption
algorithm (Intel module type).

■ Advanced Encryption Standard (AES) data

encryption, based on 256 bit encryption
algorithm (Atheros module type).

■ Wi-Fi Protected Access (WPA).

1-10 User’s Manual

Introduction

■ The numerical values shown above are the theoretical maximums for

Wireless LAN standards. The actual values may differ.

■ The transmission speed over the wireless LAN and the distance over

which wireless LAN can reach may vary depending on surrounding
electromagnetic environment, obstacles, access point design and
configuration, and client design and software/hardware configurations.
The Transmit Rate (at X Mbit/s) is the theoretical maximum speed
under the IEEE802.11 (a/b/g) standard. The actual transmission speed
will be lower than the theoretical maximum speed. To use the Atheros
Super G™ function, your client and access point must support the
corresponding feature. Performance of these functions may vary
depending on the format of data transmitted.

Disclaimer (Wireless LAN/Atheros)

For more information on the Disclaimer regarding Wireless LAN/Atheros,
please refer to the Disclaimers section in Chapter 11.

Wireless
communication
switch

Security

Security lock slot Connects a security lock to anchor the computer

Special features

The following features are either unique to TOSHIBA computers or are
advanced features, which make the computer more convenient to use.

Hot keys Key combinations let you quickly change the

The Hot key functions are supported only under Windows, they are not
supported under QosmioPlayer.

Display automatic
power off

This switch turns the Wireless LAN function on
and off.

to a desk or other large object.

system configuration directly from the keyboard
without running a system configuration program.

This feature automatically cuts off power to the
internal display when there is no keyboard input
for a time specified. Power is restored when any
key is pressed. You can specify the time in the
Monitor power off item of the Basic Setup tab in
TOSHIBA Power Saver.

User’s Manual 1-11

Introduction

HDD automatic
power off

This feature automatically cuts off power to the
hard disk drive when it is not accessed for a time
specified. Power is restored when the hard disk is
accessed. You can specify the time in the HDD
power off item of the Basic Setup tab in TOSHIBA
Power Saver.

System automatic
Standby/Hibernation

This feature automatically shuts down the system
into Standby Mode or Hibernation Mode when
there is no input or hardware access for a time
specified. You can specify the time and select
either System Standby or System Hibernation in
the System standby and System item of the Basic
Setup tab in TOSHIBA Power Saver.

Keypad overlay A ten-key pad is integrated into the keyboard.

Refer to the Keypad overlay section in Chapter 5,

The Keyboard, for instructions on using the

keypad overlay.

Power on password Two levels of password security, supervisor and

user, are available to prevent unauthorized
access to your computer.

Instant security A hot key function blanks the screen and disables

the computer providing data security.

Intelligent power
supply

A microprocessor in the computer’s intelligent
power supply detects the battery’s charge and
calculates the remaining battery capacity. It also
protects electronic components from abnormal
conditions, such as voltage overload from an AC
adaptor. You can monitor remaining battery
capacity by using the Battery remaining item in
TOSHIBA Power Saver.

Battery save mode This feature lets you save battery power. You can

specify the Power Save Mode in the Profile item
in TOSHIBA Power Saver.

Panel power on/off This feature turns power to the computer off

when the display panel is closed and turns it back
on when the panel is opened. You can specify the
setting in the When I close the lid item of the
Setup Action tab in TOSHIBA Power Saver.

Low battery
automatic
hibernation

When battery power is exhausted to the point that
computer operation cannot be continued, the
system automatically enters Hibernation and
shuts down. You can specify the setting in the
Setup Action tab in TOSHIBA Power Saver.

1-12 User’s Manual

Introduction

Heat dispersal To protect from overheating, the CPU has an

internal temperature sensor. If the computer’s
internal temperature rises to a certain level, the
cooling fan is turned on or the processing speed
is lowered. Use the Cooling Method item of the
Basic Setup tab in TOSHIBA Power Saver.

■ Maximum

Performance

■ Performance Uses a combination of

■ Battery optimized Lowers the CPU

Hibernation This feature lets you turn off the power without

exiting from your software. The contents of main
memory are saved to the hard disk, when you
turn on the power again, you can continue
working right where you left off. Refer to the

Turning off the power section in Chapter 3,
Getting Started, for details.

Standby If you have to interrupt your work, you can turn off

the power without exiting from your software.
Data is maintained in the computer’s main
memory. When you turn on the power again, you
can continue working right where you left off.

Turns on fan first, then if
necessary lowers CPU
processing speed.

fan and lowering the
CPU processing speed.

processing speed first,
then if necessary turns
on the Cooling Method.

Utilities

This section describes preinstalled utilities and tells how to start them.
For details on operations, refer to each utility’s online manual, help files or
readme.txt files.

TOSHIBA Power
Saver

HW Setup This program lets you customize your hardware

User’s Manual 1-13

To access this power savings management
program, click start, click the Control Panel,
click Performance and Maintenance and click
the TOSHIBA Power Saver icon.

settings according to the way you work with your
computer and the peripherals you use. To start
the utility, click start and click Control Panel. In
the Control Panel, click the TOSHIBA HWSetup
icon.

Introduction

TOSHIBA Controls This utility has three sections to let you do the

following:

■ Buttons: Assign applications to the REC,

Brightness down, Brightness up, Display,
TV-out buttons.

■ Media Apps: Set the mode for the audio/video

control buttons. Select the application for
audio and video playback. (It displays only by
Windows XP Home Edition.)

■ TOSHIBA Remote Control: Enable/disable

the TOSHIBA Remote Control function. (It
displays only by Windows XP Home Edition.)

Fn-esse This Windows program lets you define your own

“shortcut” keys to quickly launch applications and
speed your work in Windows. To start the utility,
click start, point to All Programs, point to

TOSHIBA, point to Utilities and click Fn-esse.

DVD Video Player The DVD Video Player is used to play

DVD-Video. It has an on-screen interface and
functions. Click start, point to All Programs,
point to InterVideo WinDVD, then click

InterVideo WinDVD.

TOSHIBA Picture
Enhancement Utility

This utility lets you change image quality
according to your viewing environment lets you
select external input settings for Video.

TOSHIBA ConfigFree TOSHIBA ConfigFree is a suite of utilities to

allow easy control of communication devices and
network connections. TOSHIBA ConfigFree also
allows you to find communication problems and
create profiles for easy switching between
locations and communication networks. To start
ConfigFree, click start, point to All Programs,
point to TOSHIBA, point to Networking and click

ConfigFree.

TOSHIBA Assist TOSHIBA Assist is a graphical user interface that

provides easy access to help and services.

TOSHIBA Zooming
Utility

This utility allows you to enlarge or reduce the
icon size on the desktop or the application
window.

RecordNow! Basic
for TOSHIBA

You can create CD/DVDs in several formats
including audio CDs that can be played on a
standard stereo CD player and data CD/DVDs to
store the files and folders on your hard disk drive.
This software can be used on a model with DVD
Super Multi drive.

1-14 User’s Manual

Introduction

DLA for TOSHIBA DLA (Drive Letter Access) is the packet writing

software which provides the function which writes
files and/or folders to DVD-RW, CD-RW and
DVD+RW discs via a drive letter like a floppy disk
or other removable disks.

TOSHIBA Hotkey
Utility for Display
Devices

This utility has the change of a display device,
and the function to change display resolution.
Press Fn + F5 to change the active display
device. Press Fn + Space keys to change the
display resolution.

TOSHIBA PC
Diagnostic Tool

TOSHIBA PC Diagnostic Tool displays basic
configuration information on the computer, and
allows specific tests to be conducted on the
built-in hardware devices. To start TOSHIBA PC
Diagnostic Tool, click start, point to All
Programs, point to TOSHIBA, point to Utility
and click PC Diagnostic Tool.

TOSHIBA Touch and
Launch

TOSHIBA TouchPad
On/Off Utility

TOSHIBA Password
Utility

CD/DVD Drive
Acoustic Silencer

TOSHIBA Touch and Launch is a tool that allows
you to perform various tasks easily using the
Touch Pad. TOSHIBA Touch and Launch is
useful in the following conditions.

■ To open a file located on the desktop whose

icon is obscured by a window.

■ To open a page contained in the Internet

Explorer Favorites menu.

■ To display the list of currently open windows

and change the active window.

Also TOSHIBA Touch and Launch provides the
following functions by customizing the settings.

■ To open a file stored in a predefined folder.

■ To quickly launch your frequently used

applications which have been registered.

This utility has the following function.
To disable/enable the Touch Pad with
Fn + F9 key.

This utility lets you set a password that restricts
access to the computer.

This utility has the function to set up the read
speed of CD.
It is ineffective in DVD.

User’s Manual 1-15

Introduction

Options

You can add a number of options to make your computer even more
powerful and convenient to use. The following options are available:

Memory expansion A 256, 512 or 1,024 MB memory module

(DDR2 533) can easily be installed in the
computer.

Battery Pack An additional battery pack can be purchased

from your TOSHIBA dealer. Use it as a spare or
replacement.

High Capacity
Battery Pack

An additional battery pack can be purchased
from your TOSHIBA dealer. Use it as a spare or
replacement.

Universal AC
Adaptor

USB FDD kit The USB floppy disk drive accommodates either

Battery Charger The battery charger lets you charge extra

100GB HDD upgrade
kit

Wireless TV Tuner The Wireless TV Tuner has two functions:

Bluetooth SD Card3 Bluetooth SD card is an optional accessory

Bluetooth USB
Adaptor

If you use your computer at more than one site
frequently, it may be convenient to purchase an
additional AC adaptor for each site so you will not
have to carry the adaptor with you.

3 1/2" 1.44-megabyte or 720-kilobyte floppy
disks through connection to a USB port. Please
note that you cannot format 720-kilobyte floppy
disks under Windows XP, but you can use
previously formatted disks.

batteries outside the computer.

100 GB Hard disk drive pack can easily be
installed in the computer.

TV tuner and wireless LAN access point. TV can
be seen, without connecting an antenna to a
computer, or the environment of wireless LAN
can be established.

compatible with the SD card slot of this computer.
You can buy the card from TOSHIBA dealer.

A Bluetooth adaptor that has a USB connector.
Wireless communications can be carried out with
Bluetooth-compatible equipment by connecting
to the USB port of the computer.

You can buy the module from TOSHIBA dealer.

1-16 User’s Manual

Qosmio F20

The Grand Tour

This chapter identifies the various components of your computer.
Become familiar with each component before you operate the computer.

Disclaimer (Non-applicable Icons)

For more information on the Disclaimer regarding Non-applicable Icons,
please refer to the Disclaimers section in Chapter 11.

Front with the display closed

The following figure shows the computer’s front with its display panel in the
closed position.

Wireless communication
indicator

System
indicators

i.LINK (IEEE1394)
port

Chapter 2

Bridge media slot

Display latch

Headphone jack

Infrared receiver
window

System indicators Five LEDs let you monitor the DC IN, power,

Display latch This latch secures the LCD panel in its closed

User’s Manual 2-1

Wireless communication
switch

Front of the computer with display closed

battery, HDD and Bridge media slot status.
Details are in the System indicators section.

position. Slide the latch to open the display.

Microphone jack

The Grand Tour

Wireless
communication
switch

Some models are equipped with a Wireless
communication.

This switch turns the Wireless LAN function on
and off.

Wireless
communication
indicator

The Wireless communication indicator glows
when the Wireless LAN function is turned on.

Some models are equipped with a Wireless
communication.

■ Turn WiFi and Bluetooth functionalities off when near a person who

may have a cardiac pacemaker implant or other medical electric
device. Radio waves may affect pacemaker or medical device
operation, possibly resulting in serious injury. Follow the instruction of
your medical device when using any WiFi or Bluetooth functionality.

■ Always turn off WiFi or Bluetooth functionality if the PC is near

automatic control equipment or appliances such as automatic doors or
fire detectors. Radio waves can cause malfunction of such equipment,
possibly resulting in serious injury.

■ Do not use the WiFi or Bluetooth functionalities near a microwave oven

or in areas subject to radio interference or magnetic fields. Interference
from a microwave oven or other source can disrupt WiFi or Bluetooth
operation.

i.LINK (IEEE1394)
port

Connect an external device, such as a digital
video camera to this port for high-speed data
transfer.

Bridge media slot This slot lets you insert an SD card, Memory

Stick (Pro), xD picture card and MultiMediaCard.
Refer to Chapter 9, Optional Devices.

Keep foreign objects out of the Bridge media slot. Never allow metal
objects, such as screws, staples and paper clips, to enter the PC or
keyboard. Foreign metal objects can create a short circuit, which can
cause PC damage and fire, possibly resulting in serious injury.

2-2 User’s Manual

The Grand Tour

Microphone jack A 3.5 mm mini microphone jack enables

connection of a three-conductor mini jack for
monaural microphone input.

Left side

Headphone (S/PDIF)
jack

This jack lets you connect digital speakers or
stereo headphones (16 ohm minimum). When
you connect a digital speaker or headphones,
the internal speakers are automatically disabled.

This jack can be used also as S/PDIF jack and
enables connection of optical digital
correspondence apparatus.

Infrared receiver
window

Infrared receiver window is provided with some
models.
This is a sensor window that receives signals
from the remote control which is provided with
your computer.

Not supported by a Windows XP Media Center
Edition model.

The following figure shows the computer’s left side.

External monitor port

S-Video out port

Cooling vents

The left side of the computer

PC card slot

PC card eject
button

External monitor
port

This external monitor port lets you connect an
external video display.

S-Video out port This S-Video out port lets you transfer NTSC or

PAL data to external devices. Refer to TV section
in Chapter 9, Optional Devices.

Cooling vents Cooling vents help CPU keep from overheating.

Do not block the cooling vents. Never allow metal objects, such as screws,
staples and paper clips, to enter the PC or keyboard. Foreign metal objects
can create a short circuit, which can cause PC damage and fire, possibly
resulting in serious injury.

User’s Manual 2-3

The Grand Tour

PC card slot This slot accommodates a 5 mm Type II card.

The slot supports 16-bit PC cards and CardBus
PC cards.

PC card eject button Use this button to remove a PC card from the PC

Right side

The following figure shows the computer’s right side.

VIDEO-IN port The port is used differently depending on the

AV-IN port

USB ports

card slot.

Modem jack

The right side of the computer

Optical media drive

type of OS used in the computer.
Windows XP Home Edition model: With the

bundled VIDEO-IN cable, external devices such
as TV, video recorders, etc., can be connected to
the computer and WinDVR and WinDVD Creator
2 Platinum can be used to edit or view the inputs.

Media Center Edition model: With the bundled
VIDEO-IN cable, the CATV or satellite set top
boxes can be connected to the computer to view
the channels. The video cannot be extracted for
editing as in the Windows XP Home Edition
model.

Please refer to Chapter 8, Using the Remote

Controller, Front operation button and
QosmioPlayer for details on how to connect the

computer with the VIDEO-IN cable.

Universal Serial Bus
(USB 2.0) ports

Two Universal Serial Bus ports are on the right
side. The port comply with the USB 2.0 standard,
which enables data transfer speeds 40 times
faster than the USB 1.1 standard (The ports also
support USB 1.1).

2-4 User’s Manual

The Grand Tour

Keep foreign objects out of the USB connectors. Never allow metal
objects, such as screws, staples and paper clips, to enter the PC or
keyboard. Foreign metal objects can create a short circuit, which can
cause PC damage and fire, possibly resulting in serious injury.

Operation of all functions of all USB devices has not been confirmed.
Some functions might not execute properly.

Modem jack In areas where an internal modem is installed as

standard equipment, there is a modem jack that
lets you use a modular cable to connect the
modem directly to a telephone line.

■ Connection to any communication line other than an analog phone line

could cause a PC system failure.

■ Connect the built-in modem only to ordinary analog phone lines.

■ Never connect the built-in modem to a digital line (ISDN).

■ Never connect the built-in modem to the digital connector on a

public telephone or to a digital private branch exchange (PBX).

■ Never connect the built-in modem to a key telephone system for

residences or offices.

■ Never operate your PC on AC power during a thunderstorm. If you see

lightning or hear thunder, immediately turn off the PC. An electric surge
caused by the storm, may result in a system failure, loss of data or
hardware damage.

Optical media drive The computer is configured with a DVD-

ROM&CD-R/RW drive or a DVD Super Multi
drive.

User’s Manual 2-5

The Grand Tour

Back side

The following figure shows the computer’s back side.

DC IN 15V jack

LAN active indicator
(orange) Link indicator (green)

Security lock slot

TV antenna port

Battery pack

The back side of the computer

LAN jack

USB port

Security lock slot A security cable attaches to this slot. The

optional security cable anchors your computer to
a desk or other large object to deter theft.

Universal Serial Bus
(USB 2.0) ports

The Universal Serial Bus port is on the back side.
Refer to Right side section, for details.

LAN jack This jack lets you connect to a LAN. The adaptor

has built-in support for Ethernet LAN (10
megabits per second, 10BASE-T) and Fast
Ethernet LAN (100 megabits per second,
100BASE-TX). The LAN has two indicators.
Refer to Chapter 4, Operating Basics, for details.

■ Do not connect any cable other than a LAN cable to the LAN jack.

It could cause damage or malfunction.

■ Do not connect the LAN cable to a power supply. It could cause

damage or malfunction.

Link indicator
(green)

This indicator glows green when the computer is
connected to a LAN and the LAN is functioning
properly.

LAN active indicator
(orange)

This indicator glows orange when data is being
exchanged between the computer and the LAN.

Battery pack The battery pack powers the computer when the

AC adaptor is not connected. For detailed
information on the battery pack, refer to
Chapter 6, Power.

2-6 User’s Manual

DC IN 15V jack The AC adaptor connects to this jack. Use only

TV antenna port The TV antenna port is provided with some

Underside

The following figure shows the underside of the computer.
Make sure the display is closed before turning over your computer.

Hard disk drive

Battery lock

The Grand Tour

the model of AC adaptor that comes with the
computer. Using the wrong adaptor can damage
your computer.

models.
Connect the antenna adaptor to this port to watch
TV programs on your computer or record them.

Memory module cover

Battery release latch

The underside of the computer

Memory module
cover

This cover protects memory module sockets.
Refer to the Memory expansion section in
Chapter 9, Optional Devices.

Battery lock Slide the battery lock towards the release

position to make the battery release latch
movable.

Battery release
latch

Slide and hold this latch to release the battery
pack for removal.

For detailed information on removing the battery
packs, refer to Chapter 6, Power.

Hard disk drive This contains a Hard disk drive pack, which can

be removed and reinstalled. For more
information on how to remove or reinstall the

Hard disk drive pack, refer to the section on the

in Chapter 9, Optional Devices.

User’s Manual 2-7

The Grand Tour

Front with the display open

This section shows the front of the computer with the display open.
Refer to the appropriate illustration for details. To open the display, slide the
display latch on the front of the display and lift up. Position the display at a
comfortable viewing angle.

Display screen

Display hinge

Stereo speaker

(Left)

Power button

Front operation button
(eleven buttons)

The front of the Touch Pad model with the display open

LCD Sensor switch
(Not shown)

Display hinge

Stereo speaker
(Right)

Volume control

Touch Pad

Touch Pad control
buttons

Display hinges The display hinges hold the display screen at

easy-to-view angles.

Display screen The LCD displays high-contrast text and

graphics. The computer’s WXGA screen consists
of 1280 × 800 pixels. Refer to Display Controller

and Modes in Appendix B.

When the computer operates on the AC adaptor
the display screen’s image will be somewhat
brighter than when it operates on battery power.
The lower brightness level is intended to save
battery power.

Stereo speakers The speakers emit sound generated by your

software as well as audio alarms, such as,
generated by the system.

2-8 User’s Manual

The Grand Tour

Keep foreign objects out of the speakers. Never allow metal objects, such
as screws, staples and paper clips, to enter the PC or keyboard. Foreign
metal objects can create a short circuit, which can cause PC damage and
fire, possibly resulting in serious injury.

Front operation
button (eleven
buttons)

Eleven buttons are available for use:
TV, CD/DVD, Play/Pause, Stop, Previous, Next,

Record, Brightness down, Brightness up, Display,
TV-out.

These buttons allow you to navigate audio/video
operations, run applications and access utilities.

Refer to Chapter 8, Using the Remote Controller,

Front operation button and QosmioPlayer for

details.

Power button Press the power button to turn the computer’s

power on and off.

Touch Pad A Touch Pad located in the palm rest is used to

control the on-screen pointer. Refer to the

Operating Basics section in Chapter 4, Operating

Basics.

Touch Pad control
buttons

Control buttons below the Touch Pad let you
select menu items or manipulate text and
graphics designated by the on-screen pointer.

LCD Sensor switch This switch senses when the LCD panel is closed

or opened and activates the Panel Power Off/On
feature. When you close the panel the computer
enters Hibernation mode and shuts down. When
you open the panel the computer starts in
Hibernation mode. Use the TOSHIBA Power
Saver Utility to enable or disable this feature.
The default is “enabled”. Refer to the TOSHIBA
Power Saver Utility and Panel Power Off/On
items in Chapter 1, Introduction, for details on
settings.

Do not put a magnetic object close to the switch. The computer will
automatically enter Hibernation mode and shut down even if the Panel
Power Off features is disabled.

Volume control Use this dial to adjust the volume of the stereo

speakers or the stereo headphones.
When the dial is turned clockwise, the volume

increases, when it is turned counterclockwise,
the volume decreases.

User’s Manual 2-9

The Grand Tour

System indicators

LEDs beneath icons, light when various computer operations are in
progress.

Battery

Power

DC IN

HDD

Bridge media slot

System indicators

DC IN The DC IN indicator glows green when DC power

is supplied from the AC power adaptor. If the
adaptor’s output voltage is abnormal or if the
power supply malfunctions, this indicator flashes
orange.

Power The Power indicator glows green when the

computer is on. If you select Standby from Shut
Down Windows, this indicator flashes orange
(one second on, two seconds off) while the
computer shuts down.

Battery The Battery indicator shows the condition of the

battery’s charge: Green indicates full charge,
orange indicates battery charging and flashing
orange indicates a low battery charge. Refer to
Chapter 6, Power.

HDD The HDD indicator glows green when the

computer is accessing the built-in hard disk drive.

Bridge media slot The Bridge media slot indicator glows green

when the computer is accessing the Bridge media
slot.

2-10 User’s Manual

Keyboard indicators

The figures below show the positions of the keypad overlay indicators and
the Caps Lock indicator.

The following indicator shows the state of an alphabet key (pressed or
released).

Caps Lock indicator

Caps Lock indicator

Caps Lock The Caps Lock indicator glows green when the

alphabet keys are locked in uppercase.

The following indicators show the status of the display overlay.

The Grand Tour

Numeric Mode
indicator

Arrow Mode indicator

Keypad overlay indicators

Arrow mode When the Arrow mode indicator lights green,

you can use the keypad overlay (gray labeled
keys) as cursor keys. Refer to the Keypad

overlay section in Chapter 5, The Keyboard.

Numeric mode You can use the keypad overlay (gray labeled

keys) for numeric input when the Numeric mode
indicator lights green. Refer to the Keypad

overlay section in Chapter 5, The Keyboard.

User’s Manual 2-11

The Grand Tour

Optical media drive

A DVD-ROM&CD-R/RW or a DVD Super Multi drive is installed in your
computer. An ATAPI interface controller is used for CD/DVD-ROM
operation. When the computer is accessing a CD/DVD, an indicator on the
drive glows.

Region codes for DVD drives and media

DVD Super Multi drives and media are manufactured according to the
specifications of six marketing regions. When you purchase DVD-Video
media, make sure it matches your drive, otherwise it will not play properly.

Code Region

1 Canada, United States

2 Japan, Europe, South Africa, Middle East

3 Southeast Asia, East Asia

4 Australia, New Zealand, Pacific Islands, Central America,

South America, Caribbean

5 Russia, Indian Subcontinent, Africa, North Korea, Mongolia

6 China

Writable discs

This section describes the types of writable CD/DVD discs. Check the
specifications for your drive to for the type of discs it can write. Use
RecordNow! to write compact discs. Refer to Chapter 4, Operating Basics.

CDs

■ CD-R discs can be written only once. The recorded data cannot be

erased or changed.

■ CD-RW discs including multi speed CD-RW discs, high-speed CD-RW

discs and ultra-speed CD-RW discs can be recorded more than once.

DVDs

■ DVD-R and DVD+R discs can be written only once. The recorded data

cannot be erased or changed.

■ DVD-RW, DVD+RW and DVD-RAM discs can be recorded more than

once.

2-12 User’s Manual

Formats

The drives support the following formats:

The Grand Tour

■ DVD-ROM

■ CD-DA

■ Photo CDTM (single/multi-session)

■ CD-ROM XA Mode 2

(Form1, Form2)

■ DVD -Video

■ CD-Text

■ CD-ROM Mode 1, Mode 2

■ Enhanced CD (CD-EXTRA)

■ Addressing Method 2

DVD-ROM&CD-R/RW drive

The full-size DVD-ROM&CD-R/RW drive module lets you record data to
rewritable CDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs
without using an adaptor.

The read speed is slower at the center of a disc and faster at the outer
edge.

DVD read 8 speed (maximum)
CD read 24 speed (maximum)
CD-R write 24 speed (maximum)
CD-RW write 24 speed (maximum, Ultra-speed media)

DVD Super Multi drive Double Layer

The full-size DVD Super Multi drive module lets you record data to
rewritable CD/DVDs as well as run either 12 cm (4.72") or 8cm (3.15”)
CD/DVDs without using an adaptor.

The read speed is slower at the center of a disc and faster at the outer
edge.

DVD read 8 speed (maximum)
DVD-R write 8 speed (maximum)
DVD-RW write 4 speed (maximum)
DVD+R write 8 speed (maximum)
DVD+RW write 4 speed (maximum)
DVD-RAM write 5 speed (maximum)
CD read 24 speed (maximum)
CD-R write 24 speed (maximum)
CD-RW write 10 speed (maximum, Ultra-speed media)
DVD+R DL 2.4 speed (maximum)

User’s Manual 2-13

The Grand Tour

AC adaptor

The AC adaptor can automatically adjust to any voltage ranging from 100 to
240 volts and to a frequency of either 50 or 60 hertz, enabling you to use
this computer in almost any country/region. The adaptor converts AC
power to DC power and reduces the voltage supplied to this computer.

To recharge the battery, simply connect the AC adaptor to a power source
and the computer. Refer to Chapter 6, Power, for details.

The AC adaptor (2-pin plug)

The AC adaptor (3-pin plug)

■ The Universal AC Adaptor and power cord bundled with this product

may differ depending on the product model. Depending on the model,
a 2-pin plug or 3-pin plug set of the above may be bundled.

■ Do not use a 3-pin to 2-pin conversion plug.

■ The supplied power cord conforms to safety rules and regulations in

the region the product is bought and should not be used outside this
region. For use in other regions, please buy power cords that conform
to safety rules and regulations in the particular region.

Always use the Toshiba AC adaptor that was provided with your PC and
the Toshiba Battery Charger (that may have been provided with your PC),
or use Toshiba recommended alternate models to avoid any risk of fire or
other damage to the PC. Use of an incompatible AC adaptor or Battery
Charger could cause fire or damage to the PC possibly resulting in serious
injury.

2-14 User’s Manual

Qosmio F20

Getting Started

This chapter provides basic information to get you started using your
computer. It covers the following topics:

■ Setting up your work space - for your health and safety

Be sure also to read Instruction Manual for Safety & Comfort. This guide,
which is included with the computer, explains product liability.

■ Connecting the AC adaptor

■ Opening the display

■ Turning on the power

■ Starting up for the first time

■ Turning off the power

■ Restarting the computer

■ Restoring the preinstalled software

Chapter 3

All users should be sure to read the section Starting up for the first time.

Setting up your work space

Establishing a comfortable work site is important for you and your
computer. A poor work environment or stressful work habits can result in
discomfort or serious injury from repetitive strain to your hands, wrists or
other joints. Proper ambient conditions should also be maintained for the
computer’s operation. This section discusses the following topics:

■ General conditions

■ Placement of the computer

■ Seating and posture

■ Lighting

■ Work habits

User’s Manual 3-1

Getting Started

General conditions

In general, if you are comfortable, so is your computer, but read the
following to make sure your work site provides a proper environment.

■ Select a work area that has:

■ a well-designed and functioning ventilation system that does not

■ good air circulation

■ a comfortable ambient temperature and relative humidity.

■ Never place your PC where it will be exposed to excess heat, such as in

direct sunlight, an unventilated vehicle or near a heater. This may result
in a system failure, malfunction, loss of data or damage to PC.

■ Never place your PC in a location where it will be exposed to extremely

low temperatures. This may result in a system failure, malfunction or
loss of data.

■ Never subject your PC to sudden temperature variations. This may

result in condensation, causing a system failure, malfunction or loss of
data.

■ Do not expose your PC to dusty environments. If dust gets inside the

PC, it could cause a system failure, malfunction or loss of data. If dust
contaminates the PC, do not turn on the power. Take it to an authorized
Toshiba service provider before you use it.

■ Never place your PC near an object that generates a magnetic field,

such as a speaker or TV. Do not wear magnetic bracelets while using
your PC. Exposure to magnetic fields can cause system failure,
malfunction or loss of data.

■ Never place a heavy object on the PC and be careful not to drop a

heavy object onto the PC. It could damage the PC or cause system
failure.

■ Never use benzene, thinner or other chemicals when cleaning the PC,

AC adaptor, or storage device. The use of benzene, thinner or other
chemicals may result in deterioration, deformation or discoloration of
those items and the loss of data.

■ Make sure the AC power cord connects to an outlet that is close to the

computer and easily accessible.

■ The temperature should be 5 to 35 degrees Centigrade

(41 to 95 degrees Fahrenheit) and the relative humidity should be
20 to 80 percent.

■ Keep the computer free of dust, moisture, and exposure to direct

sunlight.

■ Some parts of the computer, including data storage media, can be

damaged by magnets. Do not place the computer near magnetic
objects or bring magnetic objects close to the computer. Be careful of
objects, such as stereo speakers, that produce strong magnetic fields
during operation. Also, be careful with metal objects, such as bracelets,
which can be inadvertently magnetized.

■ Do not operate the computer in close proximity to a mobile phone.

forcefully direct air on you

3-2 User’s Manual

■ Leave ample ventilation room for the fan. Do not block the vents.

■ If the PC interferes with radio equipment, turn the PC power off

immediately. Such interference could cause equipment malfunction.

■ Never place your PC on a shaky table, uneven, tilted surface or other

unstable location. Your PC may fall, causing damage to the PC or
possibly injury.

■ Never leave the power to your PC on continuously for more than

24 hours. Turn the power off when this product is not in use.

■ Always avoid abrupt changes of temperature or humidity.

■ Never place close to heat radiating appliances such as a heater.

■ Never place close to corrosive chemicals.

■ Never place close to magnetic field radiating appliances such as a

stereo speaker.

■ Always place this product on a flat surface.

■ Provide a sufficient space behind the PC to allow easy adjustment of

the display panel.

■ Always provide sufficient space around the PC to ensure adequate

ventilation.

■ Always provide sufficient space for operating a mouse and other

peripheral devices.

Placement of the computer

Position the computer and peripheral devices to provide comfort and safety.

■ Position your LCD display panel or place your monitor in an appropriate

position to help reduce awkward postures and overhead glare. For
example:

■ Position LCD directly in front of you and at a comfortable distance

away.

■ Position LCD so the top of the screen is at or slightly below eye

level. A display screen that is too high or too low can cause
awkward postures and possibly fatigue muscles that support the
head.

■ Rest your eyes periodically by focusing on objects that are farther

away.

■ If you use a paper holder, set it at about the same height and distance

as the computer.

Getting Started

User’s Manual 3-3

Getting Started

Seating and posture

The height of your chair in relation to the computer and keyboard as well as
the support it gives your body are primary factors in reducing work strain.
Refer to the following tips:

■ Keep hands, wrists, and forearms straight, in-line and roughly parallel to

the floor.

■ Keep head level, or bent slightly forward, forward facing, and balanced.

Generally the head is in-line with the torso.

■ Keep shoulders relaxed and let upper arms hang normally at the side of

the body.

■ Keep elbows in close to the body and bent.

■ Keep feet fully supported by floor or foot rest.

■ Keep back fully supported with appropriate lumbar support when sitting

vertical or leaning back slightly.

■ Keep thighs and hips supported by a well-padded seat cushion and

generally parallel to the floor.

■ Keep knees about the same height as the hips with the feet slightly

forward.

Below eye level

90°angles

Foot rest

Posture and positioning of the computer

3-4 User’s Manual

Lighting

Select the right level of illumination and place your PC appropriately to
minimize glare from overhead lights, desk lamps and windows. Glare on
the LCD or monitor may cause eye strain, eye fatigue or headaches.

Consider the following suggestions regarding lighting your work
environment:

■ Position the PC so that the light source does not shine or reflect directly

onto the display or shine or reflect directly into the eyes of the user.

■ Shield the PC from direct light by using tinted windows or by installing

blinds or a screen.

■ Use soft, indirect lighting.

■ Adjust the display panel to provide maximum visibility.

Work habits

A key to avoiding discomfort or injury from repetitive strain is to vary your
activities. If possible, schedule a variety of tasks into your workday. If you
must spend long periods at the computer, finding ways to break up the
routine can reduce stress and improve your efficiency.

■ Sit in a relaxed posture. Good positioning of your chair and equipment

as described earlier can reduce tension in your shoulders or neck and
ease back strain.

■ Vary your posture frequently.

■ Occasionally stand up and stretch or exercise briefly.

■ Exercise and stretch your wrists and hands a number of times during

the day.

■ Frequently, look away from the computer and focus your eyes on a

distant object for several seconds, for example 30 seconds every
15 minutes.

■ Take frequent short breaks instead of one or two long breaks, for

example, two or three minutes every half hour.

■ When you use a PC, rest your eyes periodically and relax or stretch

your muscles to avoid strain. If you experience discomfort while
operating the PC, stop immediately and rest. Continuous operation for
long periods without adequate rest may cause pain in the arms, wrists,
hands, back, neck or other parts of the body. If pain persists despite
rest, consult your doctor.

A number of books are available on ergonomics and repetitive strain injury
or repetitive stress syndrome. For more information on these topics or for
pointers on exercises for such stress points as hands and wrists, please
check with your library or book vendor. Also refer to the computer’s

Instruction Manual for Safety & Comfort.

Getting Started

User’s Manual 3-5

Getting Started

Other Things to Note

■ Never turn off the power while an application is running. Doing so could

cause loss of data.

■ Use a virus-check program and make sure it is updated regularly.

■ Never turn off the power, disconnect an external storage device or

remove storage media during data read/write. Doing so can cause data
loss.

■ Never format storage media without checking its content. Formatting

destroys all stored data.

■ It is a good idea to periodically back up the internal hard disk or other

main storage device to external media. General storage media is not
durable or stable over long periods of time and under certain conditions
may result in data loss.

■ Before you install a device or application, save any data in memory to

the hard disk drive or other storage media. Failure to do so may result in
the loss of data.

Connecting the AC adaptor

Attach the AC adaptor when you need to charge the battery or you want to
operate from AC power. It is also the fastest way to get started, because
the battery pack will need to be charged before you can operate from
battery power.

The AC adaptor can be connected to any power source supplying from
100 to 240 volts and 50 or 60 hertz. For details on using the AC adaptor to
charge the battery pack, refer to Chapter 6, Power.

3-6 User’s Manual

Getting Started

■ Always use the Toshiba AC adaptor that was provided with your PC

and the Toshiba Battery Charger (that may have been provided with
your PC), or use Toshiba recommended alternate models to avoid any
risk of fire or other damage to the PC. Use of an incompatible AC
adaptor or Battery Charger could cause fire or damage to the PC
possibly resulting in serious injury.

■ Use only the AC adaptor supplied with your computer or an equivalent

adaptor that is compatible. Use of any incompatible adaptor could
damage your computer. TOSHIBA assumes no liability for any damage
caused by use of an incompatible adaptor.

■ Never plug the AC adaptor or Battery Charger into a power source that

does not correspond to both the voltage and the frequency specified on
the regulatory label of the unit. Failure to do so could result in a fire or
electric shock, possibly resulting in serious injury.

■ Always use or purchase power cables that comply with the legal

voltage and frequency specifications and requirements in the country of
use. Failure to do so could result in a fire or electric shock, possibly
resulting in serious injury.

■ The supplied power cord conforms to safety rules and regulations in

the region the product is bought and should not be used outside this
region. For use in other regions, please buy power cords that conform
to safety rules and regulations in the particular region.

■ Do not use a 3-pin to 2-pin conversion plug.

■ When you connect the AC adaptor to the computer, always follow the

steps in the exact order as described in the User’s Manual. Connecting
the power cable to a live electrical outlet should be the last step
otherwise the adaptor DC output plug could hold an electrical change
and cause an electrical shock or minor bodily injury when touched.
As a general safety precaution, avoid touching any metal parts.

■ Never place an AC adaptor on a wooden surface, furniture, or any

other surface that could be marred by exposure to heat since the AC
adaptor’s surface temperature increases during normal use.

■ Always place the PC on a suitable heat-insulating material to prevent

possible heat damage.

User’s Manual 3-7

Getting Started

1. Connect the power cord to the AC adaptor.

Connecting the power cord to the AC adaptor (2-pin plug)

Connecting the power cord to the AC adaptor (3-pin plug)

The Universal AC Adaptor and power cord bundled with this product may
differ depending on the product model. Depending on the model, a 2-pin
plug or 3-pin plug set of the above may be bundled.

2. Connect the AC adaptor’s DC output plug to the DC IN 15V jack on the
back side of the computer.

Do not connect the Antenna adaptor to the DC 15V IN jack.

DC IN 15V jack

Connecting the adaptor to the computer

3. Plug the power cord into a live wall outlet. The Battery and DC IN
indicators on the front of the computer should glow.

3-8 User’s Manual

Opening the display

The display panel can be rotated in a wide range of angles for optimal
viewing.

1. Slide the display latch on the front of the computer to unlatch the

display panel.

2. While holding down the palm rest with one hand so that the main body

is not raised, lift the panel slowly. Adjust the angle of the panel to
provide optimal clarity.

As the display panel cannot be opened until 180 degrees, please be
careful of the angle when flipping open the display panel.

Use reasonable care when opening and closing the display panel.
Opening it vigorously or slamming it shut could damage the computer.

Getting Started

Display latch

Opening the display

User’s Manual 3-9

Getting Started

Turning on the power

This section describes how to turn on the power.

■ After you turn on the power for the first time, do not turn it off until you

have set up the operating system. Refer to the section Starting up for

the first time.

■ If the USB floppy disk drive is connected, make sure it is empty. If a

floppy disk is in the drive, press the eject button and remove the floppy
disk.

1. Open the computer’s LCD display panel.

2. Press and hold the computer’s power button for two or three seconds.

Power button

Turning on the power

Starting up for the first time

When you first turn on the power, the computer’s initial screen is the
Microsoft Windows XP Startup Screen Logo. Follow the on-screen
directions for each screen. During setup, you can click the Back button to
return to the previous screen.

Be sure to read the License Agreement carefully.

3-10 User’s Manual

Turning off the power

The power can be turned off in one of the following modes: Shut down
(Boot), Hibernation or Standby mode.

Shut Down mode (Boot mode)

When you turn off the power in Shut Down mode no data is saved and the
computer will boot to the operating system’s main screen.

1. If you have entered data, save it to the hard disk or to a floppy disk.

2. Make sure all disk (disc) activity has stopped, then remove the

CD/DVDs or floppy disk.

■ Make sure the HDD indicator is off. If you turn off the power while a

disk (disc) is being accessed, you can lose data or damage the disk
(disc).

■ Never turn off the power while an application is running. Doing so could

cause loss of data.

■ Never turn off the power, disconnect an external storage device or

remove storage media during data read/write. Doing so can cause data
loss.

3. Click start then click Turn Off Computer. From the Turn Off

Computer menu select Tur n O ff.

4. Turn off the power to any peripheral devices.

Getting Started

Do not turn the computer or devices back on immediately. Wait a moment
to let all capacitors fully discharge.

Standby Mode

If you have to interrupt your work, you can turn off the power without exiting
from your software. Data is maintained in the computer’s main memory.
When you turn on the power again, you can continue working right where
you left off.

■ When the AC adaptor is connected, the computer will go into Standby

mode according to the settings in the TOSHIBA Power Saver utility.

■ To restore operation from Standby Mode, press the power button or

press any key. The latter action only works on the internal keyboard if
the Wake-up on Keyboard option is enabled in HW Setup.

■ If the computer automatically enters Standby mode while a network

application is active, the application might not be restored when the
computer wakes up from Standby.

■ To prevent the computer from automatically entering Standby mode,

disable Standby in TOSHIBA Power Saver. That action, however,
will nullify the computer’s Energy Star compliance.

User’s Manual 3-11

Getting Started

■ Before entering Standby mode, be sure to save your data.

■ Do not install or remove a memory module while the computer is in

Standby Mode. The computer or the module could be damaged.

■ Do not remove the battery pack while the computer is in Standby Mode

(unless the computer is connected to an AC power source). Data in
memory will be lost.

■ If you carry the computer on board an aircraft or into a hospital,

be sure to shut down the computer in hibernation mode or in shutdown
mode to avoid radio signal interference.

Benefits of standby

The standby feature provides the following benefits:

■ Restores the previous working environment more rapidly than does

hibernation.

■ Saves power by shutting down the system when the computer receives

no input or hardware access for the duration set by the System Standby
feature.

■ You can use the panel power off feature.

Executing standby

You can also enable Standby by pressing Fn + F3. Refer to Chapter 5,

The Keyboard, for details.

You can enter standby mode in one of three ways:

1. Click start, click Turn Off Computer and click Standby.

2. Close the display panel. This feature must be enabled. Refer to the
Setup Action tab in TOSHIBA Power Saver Utility described in the
Control Panel.
Open Performance and Maintenance and open TOSHIBA Power

Saver.

3. Press the power button. This feature must be enabled. Refer to the
Setup Action tab in TOSHIBA Power Saver Utility described in the
Control Panel.
Open Performance and Maintenance and open TOSHIBA Power

Saver.

When you turn the power back on, you can continue where you left when
you shut down the computer.

■ When the computer is shut down in standby mode, the power indicator

flashes orange.

■ If you are operating the computer on battery power, you can lengthen

the operating time by shutting down in hibernation mode. Standby
mode consumes more power.

3-12 User’s Manual

Standby limitations

Standby will not function under the following conditions:

■ Power is turned back on immediately after shutting down.

■ Memory circuits are exposed to static electricity or electrical noise.

Hibernation Mode

The Hibernation Mode feature saves the contents of memory to the hard
disk when the computer is turned off. The next time the computer is turned
on, the previous state is restored. The Hibernation Mode feature does not
save the status of any peripheral devices.

■ Save your data. While entering Hibernation Mode, the computer saves

the contents of memory to the hard disk drive. However, for safety
sake, it is best to save your data manually.

■ Data will be lost if you remove the battery or disconnect the AC adaptor

before the save is completed. Wait for the HDD indicator to go out.

■ Do not install or remove a memory module while the computer is in

Hibernation Mode. Data will be lost.

Benefits of Hibernation Mode

The Hibernation Mode feature provides the following benefits:

■ Saves data to the hard disk when the computer automatically shuts

down because of a low battery.

Getting Started

For the computer to shut down in Hibernation Mode, this feature must be
enabled in two places: the Hibernate tab in Power Options and Setup
Action tab in TOSHIBA Power Saver.

If you do not configure this feature, the computer will shut down in Standby
Mode - if battery power becomes depleted, data saved in Standby Mode
will be lost.

■ You can return to your previous working environment immediately when

you turn on the computer.

■ Saves power by shutting down the system when the computer receives

no input or hardware access for the duration set by the System
hibernate feature.

■ You can use the panel power off feature.

User’s Manual 3-13

Getting Started

Starting Hibernation Mode

You can also enable Hibernation Mode by pressing Fn + F4.
Refer to Chapter 5, The Keyboard, for details.

To enter Hibernation mode, follow the steps below.

1. Click start.

2. Select Turn Off Computer.

3. Open the Turn Off Computer dialog box. Hibernate is not displayed.

4. Press the Shift key. The Standby item will change to Hibernate.

5. Select Hibernate.

Automatic Hibernation

The computer will enter Hibernate mode automatically when you press the
power button or close the lid. First, however, make the appropriate settings
according to the steps below.

1. Click start and open the Control Panel.

2. Open Performance and Maintenance and open Power Options.

3. Select the Hibernate window in the Power Options Properties,
select the Enable hibernation check box and click the Apply button.

4. Open TOSHIBA Power Saver.

5. Select the Setup Action window.

6. Enable the desired Hibernation settings for When I press the power
button and When I close the lid.

7. Click the OK button.

Data save in Hibernation Mode

When you turn off the power in Hibernation Mode, the computer takes a
moment to save current memory data to the hard disk. During this time,
the HDD indicator will light.

After you turn off the computer and memory is saved to the hard disk,
turn off the power to any peripheral devices.

Do not turn the computer or devices back on immediately. Wait a moment
to let all capacitors fully discharge.

3-14 User’s Manual

Restarting the computer

Certain conditions require that you reset the system. For example, if:

■ You change certain computer settings.

■ An error occurs and the computer does not respond to your keyboard

commands.

■ There are three ways to reset the computer system:

1. Click start then click Turn off computer. From the Turn off

computer menu select Restart.

2. Press Ctrl + Alt + Del to display the Windows Task Manager, then

select Shutdown and Restart.

3. Press the power button and hold it down for five seconds. Wait 10 to

15 seconds, then turn the power on again by pressing the power button.

Restoring the preinstalled software

If preinstalled files are damaged, use the Product Recovery Media to
restore them. To restore the operating system and all preinstalled software,
follow the steps below.

Restoring the Windows operating system

When you reinstall the Windows operating system, the hard disk will be
reformatted and all data will be lost.

Getting Started

1. Load the Product Recovery DVD-ROM in the optical media drive and

turn off the computer’s power.

2. Hold down the F12 key and turn on the power. When Qosmio appears,

release the F12 key.

3. Use the left or right cursor key to select the optical media drive in the

Boot Devices menu. For details, refer to the Boot Priority section in
Chapter 7, HW Setup.

4. Follow the on-screen instructions.

5. If your computer came with additonal software installed, this software

can not be recovered from the Product Recovery DVD-ROM. Re-install
these applications (e.g. Works Suite, DVD Player, Games, etc.)
separately from other media.

User’s Manual 3-15

Getting Started

Restoring QosmioPlayer

To restore QosmioPlayer, follow the steps below.

1. Load the QosmioPlayer Recovery Media in the optical media drive and
turn off the computer’s power.

2. Hold down the F12 key and turn on the power. When Qosmio appears,
release the F12 key.

3. Use the left or right cursor key to select the Optical Media drive in the
Boot Devices menu. For details, refer to the Boot Priority section in
Chapter 7, HW Setup.

4. Follow the on-screen instructions.

Restoring TOSHIBA utilities and drivers

If Windows is working properly, individual drivers or applications can be
separately restored. The TOSHIBA Tools & Utilities folder (C:\TOOLSCD)
contains drivers and applications, which are included with your computer
system. If your system drivers or applications have become damaged in
some way, you can reinstall most of the components from this folder.

Create a copy of this folder to an external media for more convenience.

3-16 User’s Manual

Qosmio F20

Operating Basics

This chapter describes the basic operations of your computer and
precautions when using it, as well as the handling of CD/DVD.

Using the Touch Pad

To use the Touch Pad, simply touch and move your finger tip across it in the
direction you want the on-screen pointer to go.

Chapter 4

Touch Pad

Touch Pad control
buttons

Touch Pad and Touch Pad control buttons

Two buttons below the keyboard are used like the buttons on a mouse
pointer. Press the left button to select a menu item or to manipulate text or
graphics designated by the pointer. Press the right button to display a menu
or other function depending on the software you are using.

You can also tap the Touch Pad to perform functions similar to those of the
left button.

Click: Tap on ce
Double-click: Tap twice
Drag and drop: Tap to select the material you want to move. Leave

your finger on the Touch Pad after the second tap and move the
material.

User’s Manual 4-1

Operating Basics

Using optical media drives

The text and illustrations in this section refer primarily to the optional
media drive. However, operation is the same for all other optical media
drives. The full-size drive provides high-performance execution of
CD/DVD-ROM-based programs. You can run either 12 cm (4.72") or
8 cm (3.15") CD/DVDs without an adaptor. An ATAPI interface controller is
used for CD/DVD-ROM operation. When the computer is accessing a
CD/DVD-ROM, an indicator on the drive glows.

Use the WinDVD application to view DVD-Video discs.

If you have a DVD-ROM&CD-R/RW drive, refer also to the Writing CDs on

DVD-ROM&CD-R/RW drive section for precautions on writing to CDs.

If you have a DVD Super Multi drive, refer also to the Writing CDs/DVDs on

DVD Super Multi drive section for precautions on writing to CDs.

Loading discs

To load CD/DVDs, follow the steps below.
When the computer’s power is on, press the eject button to open the disc

tray slightly.

Eject button

Pressing the eject button

1. Grasp the disc tray gently and pull until it is fully opened.

Disc tray

Pulling the disc tray open

4-2 User’s Manual

Operating Basics

2. Lay the CD/DVD, label side up, in the disc tray.

Laser lens

Inserting a CD/DVD

When the disc tray is fully opened, the edge of the computer will extend
slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD
at an angle when you place it in the disc tray. After seating the CD/DVD,
however, make sure it lies flat.

■ Do not touch a laser lens and its circumference portion.

Doing so could cause misalignment.

■ Prevent foreign objects from entering the drive. Check the surface of

the disc tray, especially the area behind the front edge of the disc tray,
to make sure there are no such objects before closing the drive.

3. Press gently at the center of the CD/DVD until you feel it click into

place. The CD/DVD should lie below the top of the spindle, flush with
the spindle base.

User’s Manual 4-3

Operating Basics

Removing discs

4. Push the center of the disc tray to close it. Press gently until it locks into
place.

If the CD/DVD is not seated properly when the disc tray is closed, the
CD/DVD might be damaged. Also, the disc tray might not open fully when
you press the eject button.

Closing the CD/DVD disc tray

To remove the CD/DVD, follow the steps below.

Do not press the eject button while the computer is accessing the media
drive. Wait for the Optical media drive indicator to go out before you open
the disc tray. Also, if the CD/DVD is spinning when you open the disc tray,
wait for it to stop before you remove it.

1. To pop the disc tray partially open, press the eject button. Gently pull
the disc tray out until it is fully opened.

When the disc tray pops open slightly, wait a moment to make sure the
CD/DVD has stopped spinning before pulling the disc tray fully open.

2. The CD/DVD extends slightly over the sides of the disc tray so you can
hold it. Hold the CD/DVD gently and lift it out.

Removing a CD/DVD

3. Push the center of the disc tray to close it. Press gently until it locks into
place.

4-4 User’s Manual

How to remove CD/DVD when the disk tray will not open

Pressing the eject button will not open the disc tray when the computer
power is off. If the power is off, you can open the disc tray by inserting a
slender object (about 15 mm) such as a straightened paper clip into the
eject hole just to the right of the eject button.

Manual release with the eject hole

Turn off the power before you use the eject hole. If the CD/DVD is spinning
when you open the disc tray, the CD/DVD could fly off the spindle and
cause injury.

Writing CDs on DVD-ROM&CD-R/RW drive

Operating Basics

Eject hole

Depending on the type of drive installed, you may be able to write CDs.
The DVD-ROM&CD-R/RW drive lets you write as well as read CD-ROMs.
Observe the precautions in this section to ensure the best performance for
writing CDs. For information on loading and unloading CDs refer to the

Using optical media drives section.

■ Refer to the Writable discs, Chapter 2 for the details about the types of

writable CD/DVD discs.

■ Do not turn off the power of the optical media drive while the computer

is accessing the drive. If you turn off the power, you may lose data.

User’s Manual 4-5

Operating Basics

Before writing or rewriting

Please observe the following points when you write or rewrite the data.

■ We recommend the following manufacturers of CD-R and CD-RW

media. Media quality can affect write or rewrite success rates.

CD-R:

TAIYO YUDEN CO., LTD.
MITSUBISHI CHEMICAL CORPORATION
RICOH Co., Ltd.
Hitachi Maxell Ltd.

CD-RW:

MITSUBISHI CHEMICAL CORPORATION
RICOH Co., Ltd.

The following special media recommend the next manufacturers.

Multi-Speed and High-Speed CD-RW:

MITSUBISHI CHEMICAL CORPORATION
RICOH Co., Ltd.

Ultra-Speed CD-RW:

MITSUBISHI CHEMICAL CORPORATION

TOSHIBA has confirmed the operation of CD-R and CD-RW media of the
manufacturers above. Operation of other media cannot be guaranteed.

■ The actual number of rewrites to CD-RW is affected by the quality of the

disc and the way it is used.

■ Be sure to connect the AC adaptor when you write or rewrite.

■ Be sure to close all other software programs except the writing

software.

■ Do not run software such as a screen saver which can put a heavy load

on the CPU.

■ Operate the computer at full power. Do not use power-saving features.

■ Do not write while virus check software is running. Wait for it to finish,

then disable virus detection programs including any software that
checks files automatically in the background.

■ Do not use hard disk utilities, including those intended to enhance HDD

access speed. They may cause unstable operation and damage data.

■ Write from the computer’s HDD to the CD. Do not try to write from

shared devices such as a LAN server or any other network device.

■ Writing with software other than Sonic RecordNow! has not been

confirmed. Therefore, operation with other software cannot be
guaranteed.

4-6 User’s Manual

When writing or rewriting

Note the following when you write or rewrite a CD-R or CD-RW.

■ Always copy data from the HDD to the CD. Do not use cut-and-paste.

The original data will be lost if there is a write error.

■ Do not perform any of the following actions:

■ Change users in the Windows XP operating system.

■ Operate the computer for any other function, including use of a

mouse or Touch Pad, closing/opening the LCD panel.

■ Start a communication application such as a modem.

■ Apply impact or vibration to the computer.

■ Install, remove or connect external devices, including the following:

PC card, SD card, USB devices, external monitor, i.LINK devices,
optical digital devices.

■ Open the optical media drive.

■ Remove the optical media drive from the Slim Select Bay.

■ If the media is poor in quality, dirty or damaged, writing or rewriting

errors may occur.

■ Set the computer on a level surface and avoid places subject to

vibration such as airplanes, trains or cars. Do not use an unstable
surface such as a stand.

■ Keep mobile phones and other wireless communication devices away

from the computer.

Operating Basics

Writing CDs/DVDs on DVD Super Multi drive

You can use the DVD Super Multi drive to write data to either CD-R/RW or
DVD-R/-RW/+R/+RW/-RAM discs. The following applications for writing are
provided: RecordNow!, and DLA licensed by Sonic Solutions, and
InterVideo’s WinDVD Creator Platinum.

■ Refer to the Writable discs, Chapter 2 for the details about the types of

writable CD/DVD discs.

■ Do not turn off the power of the optical media drive while the computer

is accessing the drive. If you turn off the power, you may lose data.

Important message

Before you write or rewrite to CD-R/RW or DVD-R/-RW/+R/+RW/-RAM
discs, read and follow all setup and operating instructions in this section.
If you fail to do so, the DVD Super Multi drive may not function properly,
and you may fail to write or rewrite, lose data or incur other damage.

User’s Manual 4-7

Operating Basics

Disclaimer

TOSHIBA does not bear responsibility for the following:

■ Damage to any CD-R/RW or DVD-R/-RW/+R/+RW/-RAM disc

that may be caused by writing or rewriting with this product.

■ Any change or loss of the recorded contents of CD-R/RW or

DVD-R/-RW/+R/+RW/-RAM disc that may be caused by writing or
rewriting with this product, or for any business profit loss or business
interruption that may be caused by the change or loss of the recorded
contents.

■ Damage that may be caused by using third party equipment or

software.

Given the technological limitations of current optical disc writing drives, you
may experience unexpected writing or rewriting errors due to disc quality or
problems with hardware devices. Also, it is a good idea to make two or
more copies of important data, in case of undesired change or loss of the
recorded contents.

Before writing or rewriting

■ Based on TOSHIBA’s limited compatibility testing, we suggest the

following manufacturers of CD-R/RW and DVD-R/+R/-RW/+RW/-RAM
disc. However, in no event does TOSHIBA guarantee the operation,
quality or performance of any disc. Disc quality can affect write or
rewrite success rates.

CD-R:

TAIYO YUDEN CO., LTD.
MITSUBISHI CHEMICAL CORPORATION
RICOH Co., Ltd.
Hitachi Maxell Ltd.

CD-RW: (Multi-Speed and High-Speed)

MITSUBISHI CHEMICAL CORPORATION
RICOH Co., Ltd.

CD-RW: (Ultra-Speed)

MITSUBISHI CHEMICAL CORPORATION

DVD-R:

DVD Specifications for Recordable Disc for General Version 2.0

TAIYO YUDEN CO., LTD.
Matsushita Electric Industrial Co., Ltd

DVD+R:

MITSUBISHI CHEMICAL CORPORATION
RICOH Co., Ltd.

4-8 User’s Manual

Operating Basics

DVD+R DL: (Double Layer Recordable drive only)

MITSUBISHI CHEMICAL CORPORATION

DVD-RW:

DVD Specifications for Recordable Disc for Version 1.1 or version

1.2

VICTOR COMPANY OF JAPAN.LIMITED
MITSUBISHI CHEMICAL CORPORATION

DVD+RW:

MITSUBISHI CHEMICAL CORPORATION
RICOH Co., Ltd.

DVD-RAM: (DVD Super Multi drive only)

DVD Specifications for DVD-RAM Disc for Version 2.0, Version 2.1
or Version 2.2

Matsushita Electric Industrial Co., Ltd.
Hitachi Maxell Ltd.

This drive cannot use discs that allow writing faster than 8 speed
(DVD-R, DVD+R),4 speed (DVD-RW,DVD+RW),5 speed (DVD-RAM)

■ If the disc is poor in quality, dirty or damaged, writing or rewriting errors

may occur.Be careful to check the disc for dirt or damage before you
use it.

■ The actual number of rewrites to CD-RW, DVD-RW, DVD+RW or

DVD-RAM is affected by the quality of the disc and the way it is used.

■ There are two types of DVD-R discs: authoring and general use discs.

Do not use authoring discs. Only general use discs can be written to by
a computer drive.

■ You can use DVD-RAM discs that can be removed from a cartridge and

DVD-RAM discs designed without a cartridge.

■ Other DVD-ROM drives for computers or other DVD players may not be

able to read DVD-R/-RW or DVD+R/+RW discs.

■ Data written to a CD-R/DVD-R/DVD+R disc cannot be deleted either in

whole or in part.

■ Data deleted (erased) from a CD-RW, DVD-RW, DVD+RW and

DVD-RAM disc cannot be recovered. Check the content of the disc
carefully before you delete it. If multiple drives that can write data to
discs are connected, be careful not to delete data from the wrong drive.

■ In writing to a DVD-R/-RW, DVD+R/+RW or DVD-RAM disc, some disc

space is required for file management, so you may not be able to write
the full capacity of the disc.

■ Since the disc is based on the DVD standard, it might be filled with

dummy data if the written data is less than about 1 GB. Even if you write
only a small amount of data, it might take time to fill in the dummy data.

User’s Manual 4-9

Operating Basics

■ DVD-RAM formatted by FAT32 cannot be read in Windows 2000

without DVD-RAM Driver Software.

■ When multiple drives that can write data to discs are connected,

be careful not to write to the wrong drive.

■ Be sure to connect the AC adaptor before you write or rewrite.

■ Before you enter standby/hibernation mode, be sure to finish DVD-RAM

writing. Writing is finished if you can eject DVD-RAM media.

■ Be sure to close all other software programs except the writing

software.

■ Do not run software such as a screen saver, which can put a heavy load

on the CPU.

■ Operate the computer in the full-power mode. Do not use power-saving

features.

■ Do not write while virus check software is running. Wait for it to finish

and then disable virus detection programs including any software that
checks files automatically in the background.

■ Do not use hard disk utilities, including those intended to enhance hard

disk drive access speed. They may cause unstable operation and data
damage.

■ CD-RW (Ultra Speed +) media is not available. If used, data may be lost

or damaged.

■ DVD+R DL media is not available.

■ Write from the computer’s hard disk drive to the CD/DVD. Do not try to

write from shared devices such as a LAN server or any other network
device.

■ Writing with software other than RecordNow! and InterVideo WinDVD

Creator Platinum are not recommended.

When writing or rewriting

Please observe/consider the following when you write or rewrite to a
CD-R/RW, DVD-R/-RW/-RAM or DVD+R/+RW disc.

■ Do not perform any of the following actions when writing or rewriting:

■ Change users in the Windows XP operating system.

■ Operate the computer for any other function, including using a

mouse or Touch Pad or closing/opening the LCD panel.

■ Start a communication application such as a modem.

■ Apply impact or vibration to the computer.

■ Install, remove or connect external devices, including the following:

PC card, SD card, Memory Stick/Memory Stick Pro, xD picture card,
MultiMediaCard, USB devices, external monitor, i.LINK devices,
optical digital devices.

■ Use the Audio/Video control button to reproduce music or voice.

■ Open the optical media drive.

■ Do not use shut down/log off and standby/hibernation while writing or

rewriting.

4-10 User’s Manual

■ Make sure writing or rewriting is completed before going into

standby/hibernation. Writing is completed if you can open the
DVD-ROM&CD-R/RW or DVD Super Multi drive tray.

■ Set the computer on a level surface and avoid places subject to

vibration such as airplanes, trains, or cars. Do not use an unstable
surface such as a stand.

■ Keep mobile phones and other wireless communication devices away

from the computer.

■ Always copy data from the hard disk drive to the optical media. Do not

use cut-and-paste. The original data will be lost if there is a write error.

RecordNow! Basic for TOSHIBA

Note the following limitations when you use RecordNow!:

■ DVD-Video cannot be created using RecordNow!.

■ DVD-Audio cannot be created using RecordNow!.

■ You cannot use RecordNow!’s “Audio CD for Car or Home CD Player”

function to record music to the DVD-R/-RW or DVD+R/+RW discs.

■ Do not use the “Exact Copy” function of RecordNow! to copy

DVD-Video and DVD-ROM with copyright protection.

■ DVD-RAM disc cannot be backed up with the “Exact Copy” function of

RecordNow!.

■ You cannot back up a CD-ROM or CD-R/RW to DVD-R/-RW or

DVD+R/+RW using the “Exact Copy” function of RecordNow!.

■ You cannot back up DVD-ROM, DVD-Video, DVD-R/-RW or

DVD+R/+RW to CD-R/RW using the “Exact Copy” function of
RecordNow!.

■ RecordNow! cannot record in packet format.

■ You might not be able to use the “Exact Copy” function of RecordNow!

to back up a DVD-R/-RW or DVD+R/+RW disc that was made with
other software on a different DVD-R/-RW or DVD+R/+RW recorder.

■ If you add data to a DVD-R and DVD+R disc that you have already

recorded to, you might not be able to read the added data under some
circumstances. It cannot be read in 16-bit operating systems, such as
Windows 98SE and Windows Me. In Windows NT4, you will need
Service Pack 6 or later to read added data. In Windows 2000, you will
need Service Pack 2 or later to read it. Some DVD-ROM and
DVD-ROM&CD-R/RW drives cannot read added data regardless of the
operating system.

■ RecordNow! does not support recording to DVD-RAM discs. To record

to a DVD-RAM, use Explorer or another utility.

■ When you back up a DVD disc, be sure the source drive supports

recording to DVD-R/-RW or DVD+R/+RW discs. If the source drive
does not support recording to DVD-R/-RW or DVD+R/+RW discs,
it might not be backed up correctly.

■ When you back up a DVD-R, DVD-RW, DVD+R or DVD+RW, be sure to

use the same type of disc.

■ You cannot partially delete any data written to a CD-RW, DVD-RW or

DVD+RW disc.

Operating Basics

User’s Manual 4-11

Operating Basics

Data Verification

To verify that data is written or rewritten correctly, follow the steps below
before you write or rewrite a Data CD/DVD.

1. Click the Options button( ) on the RecordNow! Console to open the

2. Select the Data in the left-side menu.

3. Mark the Verify data written to the disc after burning check box in the

4. Click the OK button.

DLA for TOSHIBA

Note the following limitations when you use DLA:

■ This software supports only rewritable discs (DVD+RW, DVD-RW,

■ DLA does not support formatting a DVD-RAM disc and writing to it,

■ Do not use any discs that have been formatted with packet writing

■ Do not use the cut-and-paste function for files and folders. A file or

■ When writing SETUP files for an application to a disc formatted by DLA,

Options panels.

Data Options.

and CD-RW). It does not support DVD+R, DVD-R, and CD-R discs that
are not rewritable.

this function is performed by DVD-RAM Driver Software. You may find
that the DLA Format menu appears when inserting a DVD-RAM disc,
although you should use the “DVDForm” utility to format this disc.
You can run “DVDForm” by clicking the Start button and then selecting
“All Programs”, “DVD-RAM”, “DVD-RAM Driver” and “DVDForm”
sequentially.

software other than DLA. Similarly, do not use any discs that have been
formatted with DLA with any packet writing software other than DLA.
When using a disc you are not familiar with, format it by selecting
“Full Format” before using it.

folder that has been cut may be lost if writing fails due to an error on the
disc.

and then attempting to start SETUP from this disc, an error may occur.
In this case, please copy the SETUP files to the hard disk and then run
them from there.

4-12 User’s Manual

When using WinDVD Creator Platinum

You can record video back to your digital camcorder via i.LINK (IEEE1394)
using WinDVD Creator Platinum. However, there is a case where you may
find that playback sound is choppy -if this is the case follow the below
instructions:

1. Click start and select the Control Panel.

2. Click the Performance and Maintenance icon in the Control Panel.

3. Click the System icon in the Performance and Maintenance window.

4. Click the Advanced tab in the System Properties window.

5. Click the Settings icon in the “Performance” section.

6. Click the Advanced tab in the Performance Options window.

7. Click the Change icon in the “virtual memory” section.

8. Select the Custom size button in the Virtual Memory window.

9. Specify much higher values for “Initial size” and “Maximum size”.

10. Click the Set button in the Virtual Memory window.

11. Click the OK button in the Virtual Memory window.

How to make a DVD-Video

Simplified steps for making a DVD-Video from video data captured from a
DV-Camcorder:

1. Click [Start]-[All Programs] - [InterVideo WinDVD Creator2] ­[InterVideo WinDVD Creator] to launch WinDVD Creator.

2. Click [Capture] button then capture the video data from the
DV-Camcorder via IEEE1394.

3. Click [Edit] button then drag the video clips from [Video Library] tab to
the edit track.

4. Click [Make Movie] button in the top bar.

5. Double Click the Right arrow button icon in the center of right side.

6. Put a blank DVD-R/+R disc or an erased DVD-RW/+RW disc in the
drive.

7. Click [Start] to record to the disc.

8. When recording is finished, the tray opens.

Operating Basics

How to learn more about InterVideo WinDVD Creator

Please refer to the on-line Help for additional InterVideo WinDVD Creator
information.

User’s Manual 4-13

Operating Basics

Important information for use

Note the following limitations when you write video DVD:

1. Editing digital video

■ Log in with Administrator rights to use WinDVD Creator.

■ Make sure that your computer is running on AC power when using

WinDVD Creator.

■ Operate the computer at Full Power. Do not use power-saving

features.

■ While you are editing a DVD, you can display previews. However,

if another application is running, the preview might not display
properly.

■ WinDVD Creator cannot show video on the external monitor when in

simultaneous mode.

■ WinDVD Creator cannot edit or play copy protected content.

■ Do not change display settings while using WinDVD Creator.

■ Do not enter standby/hibernation mode while using WinDVD

Creator.

■ Do not operate WinDVD Creator immediately after turning on the

computer. Please wait until all disk/disc drive activity has stopped.

■ When recording to a DV-Camcorder, to ensure you capture all of

your data, let the camcorder record for a few seconds before you
begin recording your actual data.

■ CD recorder, JPEG functions, DVD-Audio, mini DVD and Video CD

functions are not supported in this version.

■ While recording video to DVD or tape, please close all other

programs.

■ Do not run software like a screen saver because it can put a heavy

load on the CPU.

■ Do not run communication applications like a modem or a LAN.

2. Before recording the video to DVD

■ When you record to DVD discs, please use only media

recommended by TOSHIBA.

■ Do not set the working drive to a slow device like a USB 1.1 hard

disk drive or it will fail to write DVD.

■ Do not perform any of the following actions:

■ Operate the computer for any other function, including using a

mouse or TouchPad or closing/opening the LCD panel.

■ Bump or cause vibration to the computer.

■ Use the Mode control button and Audio/Video control button to

reproduce music or voice.

■ Open the optical media drive.

■ Install, remove or connect external devices, including the

following:
PC card, SD card, Memory Stick/Memory Stick Pro, xD picture
card, MultiMediaCard, USB devices, external monitor, i.LINK
devices, optical digital devices.

4-14 User’s Manual

Operating Basics

■ Please verify your disc after recording important data.

■ DVD-R/+R/-RW disc cannot be written in VR format.

■ WinDVD Creator cannot export to DVD-Audio, VideoCD, miniDVD

format.

■ WinDVD Creator can write DVD-RAM/+RW in VR format, but the

disc may only play on your computer.

■ When writing to DVD disc, WinDVD Creator requires 2GB or more

over disk space every one hour of video.

■ When you make a fully recorded DVD, the chapter sequence may

not play correctly.

3. About Disc Manager

■ WinDVD Creator can edit one play list on a disc.

■ WinDVD Creator might show a different thumbnail than you

previously set in CE (Consumer Electronics) DVD-RAM recorder.

■ Using the Disc Manager, you can edit DVD-VR format on

DVD-RAM, DVD+VR format on DVD+RW, and DVD-Video format
on DVD-RW.

4. About recorded DVDs

■ Some DVD-ROM drives for personal computers or other DVD

players may not be able to read DVD-R/+R/-RW/+RW/-RAM discs.

■ When playing your recorded disc on your computer, please use the

WinDVD software application.

■ If you use an over-used rewritable disc, the full formatting might be

locked. Please use a brand new disc.

Media care

This section provides tips on protecting data stored on your CD/DVDs and
floppy disks.

Handle your media with care. The following simple precautions will
increase the lifetime of your media and protect the data stored on them:

CD/DVDs

1. Store your CD/DVDs in the container they came in to protect them and
keep them clean.

2. Do not bend the CD/DVD.

3. Do not write on, apply a sticker to, or otherwise mar the surface of the
CD/DVD that contains data.

4. Hold the CD/DVD by its outside edge or the edge on the center hole.
Fingerprints on the surface can prevent the drive from properly reading
data.

5. Do not expose to direct sunlight, extreme heat or cold. Do not place
heavy objects on your CD/DVDs.

User’s Manual 4-15

Operating Basics

Floppy disks

6. If your CD/DVDs become dusty or dirty, wipe them with a clean dry
cloth. Wipe from the center out, do not wipe in a circular direction
around the CD/DVD. If necessary, use a cloth dampened in water or a
neutral cleaner. Do not use benzine, thinner or similar cleaner.

The USB floppy disk drive is available only as an option.

1. Store your floppy disks in the container they came in to protect them
and keep them clean. If a floppy disk is dirty, do not use cleaning fluid.
Clean it with a soft damp cloth.

2. Never open the shutter or touch the magnetic surface of your floppy
disk. You could permanently damage it and lose data.

3. Always handle floppy disks with care, to prevent the loss of stored data.
Always apply the floppy disk label in the correct location. Never apply a
new label on top of an existing one. The label could come loose and
damage the floppy drive.

4. Never use a pencil for writing on a floppy disk label. Pencil lead dust
could cause a system malfunction. Always use a felt-tipped pen.
When writing a title on a label, first write on the label, then apply the
label to the floppy disk.

5. Never put a floppy disk in a location where water or other liquid may
contact it or where it is excessively damp. It could cause data loss.
Never use a wet or damp floppy disk. It could damage the floppy disk
drive or other devices.

6. Data may be lost if the floppy disk is twisted; bent; or exposed to direct
sunlight, extreme heat or cold.

7. Do not place heavy objects on your floppy disks.

8. Do not eat, smoke, or use erasers near your floppy disks. Foreign
particles inside the floppy disk’s jacket can damage the magnetic surface.

9. Magnetic energy can destroy the data on your floppy disks. Keep your
floppy disks away from speakers, radios, television sets and other
sources of magnetic fields.

TV Tuner

Your model allows you to watch TV programs on the biult-in LCD and to
record them.

If you have Windows XP Home Edition installed, use the WinDVR program
to display TV programs on the built-in LCD and record them. It is also
possible to edit recorded programs and save them on a DVD.

If you have Windows XP Media Center Edition installed, use the My TV
feature contained in Media Center.

According to the government regulations, it is not permitted to bring
PAL/SECAM TV tuners into Korea.

4-16 User’s Manual

Using the TV Tuner

Antenna

■ The quality of sounds and pictures greatly depends on the radio

propagation conditions.

■ When you use your computer in areas where the radio waves are

weak, which results in poor radio receiving conditions, contact the
dealer you purchased it from, or use a commercially available
antenna booster. Please refer to the manual provided with the
booster for details.

Connecting the Cable

Use the antenna adaptor that comes with the product to connect the
antenna to your computer.

Connecting the antenna adaptor

When lightning occurs, do not touch the antenna line. This may cause an
electric shock.

If you have to operate your computer during a thunderstorm and are
connecting the TV tuner to an outside antenna, you should operate your
computer using AC power mode. The AC adaptor offers some protection
against (but does not entirely prevent) possible electric shock caused by
lightning. For complete protection, do not operate your computer during a
thunderstorm.

Operating Basics

1. Save data, shutdown Windows and turn off the power.

2. Connect the antenna adaptor to the TV antenna port of your computer.

Do not connect the Antenna adaptor to the DC 15V IN jack.

TV antenna port

Antenna adaptor

Connecting the antenna adaptor

User’s Manual 4-17

Operating Basics

3. Connect the antenna cable to the other end of the antenna adaptor.

Do not connect the Antenna adaptor to the DC 15V IN jack.

Antenna adaptor

Antenna cable

Connecting the antenna cable

When you have been using a descrambler to receive the programs on
cable TV or satellite broadcasting, connect the descrambler to the antenna
cable.

Precautions when using WinDVR

Refer to the online help of WinDVR for details.

■ TV programs or other visual sources that have been recorded with

WinDVR can be used for personal uses only.

■ When WinDVR is running, do not change the screen resolution or the

color depth setting.

■ Before recording or editing video or sound which is important to you,

run a test session to see if your operations work correctly.

■ Scheduled video recording is not available when your computer is

powered off.

■ When an Internet security software application such as Norton Internet

Security is used, a security message appears at the start of the
scheduled recording, which may prevent recording. Be sure to check
whether the scheduled recording is possible.

■ When setting up a scheduled recording, be sure to check the maximum

recordable time.

■ Be sure to connect the AC adaptor to your computer so that it is

powered by AC power. With the battery power, recording may fail or
sound may skip due to a possible low battery condition.

■ There may be cases where video is not played smoothly depending on

operating conditions or scenes to be played.

4-18 User’s Manual

Operating Basics

■ When the CPU load increases during recording or playing sessions,

a time lag between video and audio may occur. In these cases,
exit WinDVR and all other application and then restart WinDVR.

■ The video may skip or stop when a shock or vibration is applied to your

computer during recording or playing sessions.

■ You can use a video deck to send the video data on a tape to this

product. However, if the tape is old or has noise, the copy protection
feature is triggered, which may result in improper operation.

■ To receive CATV programs, you need to subscribe to a CATV provider

for each device you will use. To watch or record paid programs, you
may have to use a home terminal (adaptor). For more information, refer
to the manual provided with the adaptor, or contact the CATV company.

■ Contents that are protected by copyright laws may not be recorded or

viewed with WinDVR.

■ The channel auto scan feature sometimes does not detect channels

even if they are normally detected. If it is the case, use the fine-tuning
feature for adjustment.

■ When the CPU load gets high, frame drops or a time lag between video

and audio may occur. For this reason, do not use other applications
while WinDVR is running.

■ Scheduled recording is not available after you have logged off.

■ WinDVR must be installed using the Administrator account.

■ When two sequential scheduled recording sessions have been

reserved, the first session will terminate about 2 minutes before the
specified end time. This is because the second session needs a time
for preparation (For example, if two recording sessions of 1:00-2:00pm
and 2:00-3:00pm have been booked, the 1:00-2:00pm session will
terminate about 2 minutes earlier, that is, at about 1:58pm).

■ When you have set a password for the user account, scheduled

recording cannot be performed if Standby Mode is activated.

■ Even if you click the Stop Auto Scan button, the scan may not be

stopped due to the timing of processing. In that case, click the button
repeatedly.

■ If you exit WinDVR one minute or less before the scheduled recording

starts, recording may not be performed correctly. Therefore, do not
close WinDVR during a period of one minute before the scheduled
recording start time.

■ When video is imported from a video deck or other devices, noise may

appear in the top or bottom part of the screen. This noise is due to the
display areas called vertical blanking intervals, and not a failure.

User’s Manual 4-19

Operating Basics

Sound System

Using the microphone

Your computer has a built-in microphone that can be used to record
monaural sounds into your applications. It can also be used to issue voice
commands to applications that support such functions.

Since your computer has a built-in microphone and speakers, “howling”
may be heard under certain conditions. Howling occurs when sound from
the speaker is picked up in the microphone and amplified back to the
speaker, which amplifies it again to the microphone.

This howling occurs repeatedly and causes a very loud, high-pitched noise.
It is a common phenomenon that occurs in any sound system when the
microphone input is output to the speaker (throughput) and the speaker
volume is too loud or too close to the microphone. You can control
throughput by adjusting the volume of your speaker or through the Mute
function.

To adjust the volume or activate Mute, click start, point to All Programs,
point to Accessories, point to Entertainment and click Volume control.
In the Master volume panel, you can use the slide bars to adjust the
volume level or click Mute at the bottom of the panel.

SoundMAX control panel

The SoundMAX control panel lets you control additional functions for the
Microphone Enhancement and Audio Power Management. To launch the
SoundMAX Control Panel, follow the steps below.

1. Click start and click Control Panel.

2. If you are viewing the Control Panel in Category View, click on Switch
to Classic View.

3. Double-click the SoundMAX icon.

The Microphone Setup allows you to optimize the microphone input
settings for your particular configuration. Choose Standard Microphone if
you have an ordinary desktop microphone. Choose Headset if you have a
wearable microphone that is positioned directly in front of your mouth.

You can launch the Setup Wizard from the Control Panel to help you to
automatically set proper microphone input volumes and ensure that your
voice input(s) are working correctly. As you speak into the microphone,
the Sound Meter indicates the audio signal that your PC is receiving.

The Microphone Enhancements help you to eliminate ambient noise from
the voice input signal to provide a clean and clear signal to applications.
This feature can be used with any microphone.

The audio controller can be powered down when the audio function is idle.
To enable the Audio Power Management, follow the steps below.

4-20 User’s Manual

1. Click the Power Management tab.

2. Select the Normal Power Savings in the Power Mode pull-down list.

If the No Power Savings is selected, the audio controller always runs.

If you want a more effective power management configuration, you can
select another mode, such as High Power Savings which can save more
power than the Normal Power Savings. To select this option, follow the
steps below.

1. Click the Power Management tab.

2. Select the High Power Savings in the Power Mode pull-down list.

3. Input a time in Power Save Delay (Seconds).

If the High Power Saving is selected, you need to play an audio file once
before you use a microphone or play an audio CD by the analog CD audio.

Virtual Sound

TOSHIBA Virtual Sound works as an audio filter using SRS WOW XT and
SRS TruSurround XT functions provided by SRS Labs, Inc. in the United
States. The audio filter enables you to enjoy better quality sound and music
on your computer. For more information on using the TOSHIBA Virtual
Sound, refer to its help file.

Disclaimer (SRS)

For more information on the Disclaimer regarding SRS, please refer to the
Disclaimers section in Chapter 11.

Operating Basics

Modem

This section describes how to connect and disconnect the internal modem
to and from a telephone jack.

■ Connection to any communication line other than an analog phone line

could cause a PC system failure.

■ Connect the built-in modem only to ordinary analog phone lines.

■ Never connect the built-in modem to a digital line (ISDN).

■ Never connect the built-in modem to the digital connector on a

public telephone or to a digital private branch exchange (PBX).

■ Never connect the built-in modem to a key telephone system for

residences or offices.

■ Never operate your PC on AC power during a thunderstorm. If you see

lightning or hear thunder, immediately turn off the PC. An electric surge
caused by the storm, may result in a system failure, loss of data or
hardware damage.

User’s Manual 4-21

Operating Basics

Region selection

Telecommunication regulations vary from one region to another, so you will
need to make sure the internal modem’s settings are correct for the region
in which it will be used.

The built-in modem can be used only in specified countries and regions.
Using the modem in an area not specified for use may cause a system
failure. Check the specified areas carefully before using it.

To select a region, follow the steps below.

1. Click start, point to All Programs, point to TOSHIBA, point to

Do not use the Country/Region Select function in the Modem setup
utility in the Control Panel if the function is available. If you change the
Country/Region in the Control Panel, the change may not take effect.

2. The Region Selection icon will appear in the Windows Task Bar.

3. Select a region from the region menu or a telephony location from the

Networking and click Modem Region Select.

Click the icon with the primary mouse button to display a list of regions
that the modem supports. A sub menu for telephony location
information will also be displayed. A check will appear next to the
currently selected region and telephony location.

sub-menu.

■ When you click a region it becomes the modem’s region selection,

and the New Location for telephony will be set automatically.

■ When you select a telephony location, the corresponding region is

automatically selected and it becomes the modem’s current region
setting.

Properties menu

Click the icon with the secondary mouse button to display properties menu
on the screen.

4-22 User’s Manual

Setting

You can enable or disable the following settings:

AutoRun Mode

The Region Select utility starts automatically when you start up the
operating system.

Open the Dialing Properties dialog box after selecting region.

The dialing properties dialog box will be displayed automatically after you
select the region.

Location list for region selection.

A submenu appears displaying location information for telephony.

Open dialog box, if the modem and Telephony Current
Location region code do not match.

A warning dialog box is displayed if current settings for region code and
telephony location are incorrect.

Modem Selection

If the computer cannot recognize the internal modem, a dialog box is
displayed. Select the COM port for your modem to use.

Operating Basics

Dialing Properties

Select this item to display the dialing properties.

If you are using the computer in Japan, the Telecommunications Business
Law requires that you select Japan region mode. It is illegal to use the
modem in Japan with any other selection.

Connecting

To connect the modular cable, follow the steps below.

The modular cable that comes with the computer must be used to connect
a modem. Connect the end of the modular cable with the core to the
computer.

User’s Manual 4-23

Operating Basics

■ Connection to any communication line other than an analog phone line

could cause a PC system failure.

■ Connect the built-in modem only to ordinary analog phone lines.

■ Never connect the built-in modem to a digital line (ISDN).

■ Never connect the built-in modem to the digital connector on a

public telephone or to a digital private branch exchange (PBX).

■ Never connect the built-in modem to a key telephone system for

residences or offices.

■ Never operate your PC on AC power during a thunderstorm. If you see

lightning or hear thunder, immediately turn off the PC. An electric surge
caused by the storm, may result in a system failure, loss of data or
hardware damage.

1. Plug one end of the modular cable into the computer’s modem jack.

2. Plug the other end of the modular cable into a telephone jack.

Modem jack

Connecting the internal modem

Telephone jack

Do not pull on the cable or move the computer while the cable is
connected.

If you use a storage device such as an optical drive or hard disk drive
connected to a 16-bit PC card, you might experience the following modem
problems:

■ Modem speed is slow or communication is interrupted.

■ Skips may occur in sound.

Disconnecting

To disconnect the modular cable, follow the steps below.

1. Pinch the lever on the connector in the telephone jack and pull out the
connector.

2. Disconnect the modular cable from the computer’s modem jack in the
same manner.

4-24 User’s Manual

Wireless communications

The computer’s wireless communication function supports Wireless LAN
devices.

Wireless LAN

The Wireless LAN is compatible with other LAN systems based on Direct
Sequence Spread Spectrum/Orthogonal Frequency Division Multiplexing
radio technology that complies with IEEE802.11 Wireless LAN standard
(Revision A, B or G) and Turbo Mode.

Supported features. It supports the following features:

■ Theoretical maximum speed: 54Mbps (IEEE802.11a, 802.11g)

■ Theoretical maximum speed: 11Mbps (IEEE802.11b)

■ Frequency Channel Selection

(Revision A/Turbo Mode:5 GHz, Revision B/G: 2.4 GHz)

■ Roaming over multiple channels

■ Card Power Management

■ Wired Equivalent Privacy (WEP) data encryption,

based on the 152 bit encryption algorithm (Atheros module type).

■ Wired Equivalent Privacy (WEP) data encryption,

based on the 128 bit encryption algorithm (Intel module type).

■ Advanced Encryption Standard (AES) data encryption,

based on 256 bit encryption algorithm (Atheros module type).

■ Wi-Fi Protected Access (WPA).

Operating Basics

■ The numerical values for display are the theoretical maximums for

Wireless LAN standards. The actual values may differ.

■ The transmission speed over the wireless LAN and the distance over

which wireless LAN can reach may vary depending on surrounding
electromagnetic environment, obstacles, access point design and
configuration, and client design and software/hardware configurations.
The Transmit Rate (at X Mbit/s) is the theoretical maximum speed
under the IEEE802.11 (a/b/g) standard. The actual transmission speed
will be lower than the theoretical maximum speed. To use the Atheros
Super G
corresponding feature. Performance of these functions may vary
depending on the format of data transmitted.

TM

function, your client and access point must support the

Security

■ TOSHIBA strongly recommend that you enable WEP (encryption)

functionality, otherwise your computer will be open to illegal access by
an outsider using a wireless connection. If this occurs, the outsider may
illegally access your system, eavesdrop, or cause the loss or
destruction of stored data.

■ TOSHIBA is not liable for the loss of data due to eavesdropping or

illegal access through the wireless LAN and the damage thereof.

User’s Manual 4-25

Operating Basics

Wireless communication switch

You can enable or disable Wireless LAN function, with the on/off switch.
No transmissions are sent or received when the switch is off. Slide the
switch to the right to turn it on and to the left to turn it off.

■ Do not use the WiFi or Bluetooth functionalities near a microwave oven

or in areas subject to radio interference or magnetic fields. Interference
from a microwave oven or other source can disrupt WiFi or Bluetooth
operation.

■ Turn WiFi and Bluetooth functionalities off when near a person who

may have a cardiac pacemaker implant or other medical electric
device. Radio waves may affect pacemaker or medical device
operation, possibly resulting in serious injury. Follow the instruction of
your medical device when using any WiFi or Bluetooth functionality.

■ Always turn off WiFi or Bluetooth functionality if the PC is near

automatic control equipment or appliances such as automatic doors or
fire detectors. Radio waves can cause malfunction of such equipment,
possibly resulting in serious injury.

Wireless communication indicator

The wireless communication indicator indicates the status of the wireless
communication functions.

Indicator status Indication

Indicator off Wireless communication switch is set to off.

Indicator glows Wireless communication switch is on.

Wireless LAN can be used by an application.

If you used the Task Bar to disable the Wireless LAN you will need to
restart the computer or follow the procedures below to enable the system to
once again recognize and use wireless communications. Open or click the
following: start, Control Panel, System, Hardware Device Manager,

Network adapters, Intel

®

PRO/Wireless 2200BG/2915ABG Network
Connection or Atheros AR5005GS/AR5006XS Wireless Network
Adapter and then select enable.

4-26 User’s Manual

LAN

The computer has built-in support for Ethernet LAN (10 megabits per
second, 10BASE-T) and Fast Ethernet LAN (100 megabits per second,
100BASE-TX). This section describes how to connect/disconnect to a LAN.

LAN cable types

The computer must be configured properly before connecting to a LAN.
Logging onto a LAN using the computer’s default settings could cause a
malfunction in LAN operation. Check with your LAN administrator
regarding set-up procedures.

If you are using Fast Ethernet LAN (100 megabits per second,
100BASE-TX), be sure to connect with a CAT5 cable.
You cannot use a CAT3 cable.

If you are using Ethernet LAN (10 megabits per second, 10BASE-T),
you can connect with either a CAT5 or a CAT3.

Connecting LAN cable

To connect the LAN cable, follow the steps below.

■ Connect the AC adaptor before connecting the LAN cable. The AC

adaptor must remain connected during LAN use. If you disconnect the
AC Adaptor while the computer is accessing a LAN, the system may
hang up.

■ Do not connect any other cable to the LAN jack except the LAN cable.

Otherwise, malfunctions or damage may occur.

■ Do not connect any power supplying device to the LAN cable that is

connected to the LAN jack. Otherwise, malfunctions or damage may
occur.

Operating Basics

1. Turn off the power to the computer and to all external devices
connected to the computer.

2. Plug one end of the cable into the LAN jack. Press gently until you hear
the latch click into place.

LAN jack

Connecting the LAN cable

User’s Manual 4-27

Operating Basics

3. Plug the other end of the cable into a LAN hub connector.
Check with your LAN administrator before connecting to a hub.

When the computer is exchanging data with the LAN, the LAN Active
indicator glows orange. When the computer is connected to a LAN hub but
is not exchanging data, the Link indicator glows green.

Disconnecting LAN cable

To disconnect the LAN cable, follow the steps below.

Make sure the LAN Active indicator (orange LED) is out before you
disconnect the computer from the LAN.

1. Pinch the lever on the connector in the computer’s LAN jack and pull
out the connector.

2. Disconnect the cable from the LAN hub in the same manner.
Check with your LAN administrator before disconnecting from the hub.

Cleaning the computer

To help ensure long, trouble-free operation, keep the computer free of dust
and use care with liquids around the computer.

■ Be careful not to spill liquids into the computer. If the computer does get

wet, turn the power off immediately and let the computer dry completely
before you turn it on again.

■ Clean the computer using a slightly damp (with water) cloth. You can

use glass cleaner on the display. Spray a small amount of cleaner on a
soft, clean cloth and wipe the screen gently with the cloth.

Never spray cleaner directly onto the computer or let liquid run into any
part of it. Never use harsh or caustic chemical products to clean the
computer.

Moving the computer

The computer is designed for rugged durability. However, a few simple
precautions taken when moving the computer will help ensure trouble-free
operation.

■ Make sure all disk activity has ended before moving the computer.

Check the HDD indicator on the computer.

■ If a CD/DVD is in the drive, remove it. Also make sure the disc tray is

securely closed.

■ Turn off the power to the computer.

■ Disconnect the AC adaptor and all peripherals before moving the

computer.

■ Close the LCD display panel. Do not pick up the computer by its display

panel.

4-28 User’s Manual