Toshiba e-STUDIO 850, e-STUDIO 520, e-STUDIO 281C, e-STUDIO 351C, e-STUDIO 451C User Manual

Guidance for

AS/400 Print Solution

2 AS/400 Print Solution —

AS/400 Print Solution — Software License Agreement 3

Software License Agreement

INSTALLING OR OTHERWISE USING THIS SOFTWARE PRODUCT CONSTITUTES YOUR
ACCEPTANCE OF THE FOLLOWING TERMS AND CONDITIONS (UNLESS A SEPARATE
LICENSE IS PROVIDED BY THE SUPPLIER OF APPLICABLE SOFTWARE IN WHICH CASE
SUCH SEPARATE LICENSE SHALL APPLY). IF YOU DO NOT ACCEPT THESE TERMS, YOU
MAY NOT INSTALL OR USE THIS SOFTWARE, AND YOU MUST PROMPTLY RETURN THE
SOFTWARE TO THE LOCATION WHERE YOU OBTAINED IT.

THE SOFTWARE INSTALLED ON THIS PRODUCT INCLUDES NUMEROUS INDIVIDUAL
SOFTWARE COMPONENTS, EACH HAVING ITS OWN APPLICABLE END USER LICENSE
AGREEMENT (“EULA”). INFORMATION RELATING TO THE EULAS MAY BE FOUND IN AN
ELECTRONIC FILE INCLUDED ON THE USER DOCUMENTATION CD-ROM INCLUDED HERE­WITH; HOWEVER, ALL SOFTWARE AND DOCUMENTATION DEVELOPED OR CREATED BY
OR FOR TOSHIBA TEC CORPORATION (“TTEC”) ARE PROPRIETARY PRODUCTS OF TTEC
AND ARE PROTECTED BY COPYRIGHT LAWS, INTERNATIONAL TREATY PROVISIONS,
AND OTHER APPLICABLE LAWS.

Grant of License

This is a legal agreement between you, the end-user (“You”), and TTEC and its suppliers. This
software, fonts (including their typefaces) and related documentation (“Software”) is licensed for
use with the system CPU on which it was installed (“System”) in accordance with the terms con­tained in this Agreement. This Software is proprietary to TTEC and/or its suppliers.

TTEC and its suppliers disclaim responsibility for the installation and/or use of this Software, and
for the results obtained by using this Software. You may use one copy of the Software as installed
on a single System, and may not copy the Software for any reason except as necessary to use the
Software on a single System. Any copies of the Software shall be subject to the conditions of this
Agreement.

You may not, nor cause or permit any third party to, modify, adapt, merge, translate, reverse com­pile, reverse assemble, or reverse engineer the Software. You may not use the Software, except in
accordance with this license. No title to the intellectual property in the Software is transferred to
you and full ownership is retained by TTEC or its suppliers. Source code of the Software is not
licensed to you. You will be held legally responsible for any copyright infringement, unauthorized
transfer, reproduction or use of the Software or its documentation.

Term

This license is effective until terminated by TTEC or upon your failure to comply with any term of
this Agreement. Upon termination, you agree to destroy all copies of the Software and its docu­mentation.

You may terminate this license at any time by destroying the Software and its documentation and
all copies.

Disclaimer of Warranty

THIS SOFTWARE IS PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND NON-INFRINGE­MENT. TTEC AND ITS SUPPLIERS DISCLAIM ANY WARRANTY RELATING TO THE QUALITY
AND PERFORMANCE OF THE SOFTWARE. IF THE SOFTWARE PROVES DEFECTIVE, YOU
(AND NOT TTEC OR ITS SUPPLIERS) SHALL BE RESPONSIBLE FOR THE ENTIRE COST OF
ALL NECESSARY SERVICING, REPAIR OR CORRECTION. TTEC AND ITS SUPPLIERS DO
NOT WARRANT THAT THE FUNCTIONS CONTAINED IN THE SOFTWARE WILL MEET YOUR
REQUIREMENTS OR THAT THE OPERATION OF THE SOFTWARE WILL BE UNINTER­RUPTED OR ERROR FREE.

ALL INFORMATION CONTAINED HEREIN THAT IS PROVIDED BY TTEC AND ITS AFFILIATES
PURSUANT TO A EULA IS PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESS OR IMPLIED.

4 AS/400 Print Solution — Software License Agreement

Limitation of Liability

IN NO EVENT WILL TTEC OR ITS SUPPLIERS BE LIABLE TO YOU FOR ANY DAMAGES,
WHETHER IN CONTRACT, TORT, OR OTHERWISE (EXCEPT PERSONAL INJURY OR DEATH
RESULTING FROM NEGLIGENCE ON THE PART OF TTEC OR ITS SUPPLIERS), INCLUDING
WITHOUT LIMITATION ANY LOST PROFITS, LOST DATA, LOST SAVINGS OR OTHER INCI­DENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABIL­ITY TO USE THE SOFTWARE, EVEN IF TTEC OR ITS SUPPLIERS HAVE BEEN ADVISED OF
THE POSSIBILITY OF SUCH DAMAGES, NOR FOR THIRD PARTY CLAIMS.

U.S. Government Restricted Rights

The Software is provided with RESTRICTED RIGHTS. Use, duplication or disclosure by the U.S.
Government is subject to restrictions set forth in subdivision (b) (3) (ii) or (c) (i) (ii) of the Rights in
Technical Data and Computer Software Clause set forth in 252.227-7013, or 52.227-19 (c) (2) of
the DOD FAR, as appropriate. Contractor/Manufacturer is TOSHIBA TEC Corporation, 6-78,
Minami-cho, Mishima City, Shizuoka, 411-8520, Japan.

General

You may not sublicense, lease, rent, assign or transfer this license or the Software. Any attempt to
sublicense, lease, rent, assign or transfer any of the rights, duties or obligations hereunder is void.
You agree that you do not intend to, and will not ship, transmit (directly or indirectly) the Software,
including any copies of the Software, or any technical data contained in the Software or its media,
or any direct product thereof, to any country or destination prohibited by the United States Govern­ment. This license shall be governed by the laws of Japan or, at the election of a Supplier of TTEC
concerned with a dispute arising from or relating to this Agreement, the laws of the Country desig­nated from time to time by the relevant Supplier of TTEC. If any provision or portion of this Agree­ment shall be found to be illegal, invalid or unenforceable, the remaining provisions or portions
shall remain in full force and effect.

YOU ACKNOWLEDGE THAT YOU HAVE READ THIS LICENSE AGREEMENT AND THAT YOU
UNDERSTAND ITS PROVISIONS. YOU AGREE TO BE BOUND BY ITS TERMS AND CONDI­TIONS. YOU FURTHER AGREE THAT THIS LICENSE AGREEMENT CONTAINS THE COM­PLETE AND EXCLUSIVE AGREEMENT BETWEEN YOU AND TTEC AND ITS SUPPLIERS AND
SUPERSEDES ANY PROPOSAL OR PRIOR AGREEMENT, ORAL OR WRITTEN, OR ANY
OTHER COMMUNICATION RELATING TO THE SUBJECT MATTER OF THIS LICENSE
AGREEMENT.

TOSHIBA TEC Corporation, 6-78, Minami-cho, Mishima City, Shizuoka, 411-8520, Japan.

AS/400 Print Solution — Trademarks and Copyright 5

Trademarks and Copyright

Trademarks

• Copyright permissions regarding screenshots, pictures and descriptions, included in

this document, can be obtained from AXIS Communications AB.

• AXIS Communications, AXIS 5570e, AXIS 5570e IPDS SNA and design (the AXIS

logo) are either registered trademarks or trademarks of AXIS AB and AXIS Commu­nications AB in Sweden, the European Union, the United States, Japan and other
countries.
All "AXIS 5570e" described henceforth means "AXIS 5570e IPDS SNA".

• AS/400 is a registered trademark of US International Business Machines Corpora-

tion.

• Other company names and product names in this manual are the trademarks of

their respective companies.

Copyright

© 2006 - 2010 TOSHIBA TEC CORPORATION All rights reserved
This manual is protected by copyright laws. No part of this manual shall be duplicated or repro­duced without the permission of TOSHIBA TEC CORPORATION. TOSHIBA TEC CORPORATION
shall not be liable in terms of granting patents for any use of information contained in this manual
by third parties.

6 AS/400 Print Solution — Disclaimer Notice

Disclaimer Notice

The following notice sets out the exclusions and limitations of liability of TOSHIBA TEC
CORPORATION (including its employees, agents and sub-contractors) to any pur­chaser or user (‘User’) of the e-STUDIO520/600/720/850, e-STUDIO281C/351C/451C,
e-STUDIO352/452, e-STUDIO202L/232/282, e-STUDIO2500C/3500C/3510C,
e-STUDIO165/205, e-STUDIO167/207/237, e-STUDIO523/603/723/853,
e-STUDIO353/453, e-STUDIO203L/233/283, e-STUDIO2020C/2330C/2820C/2830C/
3520C/3530C/4520C, e-STUDIO5520C/6520C/6530C, e-STUDIO283C/353C/453C,
e-STUDIO205L/255/305/355/455, e-STUDIO555/655/755/855 and e-STUDIO182/212/
242 including its accessories, options and bundled software (‘Product’).

1. The exclusion and limitations of liability referred to in this notice shall be effective to
the fullest extent permissible at law. For the avoidance of doubt, nothing in this
notice shall be taken to exclude or limit TOSHIBA TEC CORPORATION’s liability for
death or personal injury caused by TOSHIBA TEC CORPORATION’s negligence or
TOSHIBA TEC CORPORATION’s fraudulent misrepresentation.

2. All warranties, conditions and other terms implied by law are, to the fullest extent
permitted by law, excluded and no such implied warranties are given or apply in
relation to the Products.

3. TOSHIBA TEC CORPORATION shall not be liable for any loss, cost, expense,
claim or damage whatsoever caused by any of the following:

- use or handling of the Product otherwise than in accordance with the manuals,

including but not limited to Operator’s Manual, User’s Guide, and/or incorrect or
careless handling or use of the Product;

- any cause which prevents the Product from operating or functioning correctly

which arises from or is attributable to either acts, omissions, events or accidents
beyond the reasonable control of TOSHIBA TEC CORPORATION including
without limitation acts of God, war, riot, civil commotion, malicious or deliberate
damage, fire, flood, or storm, natural calamity, earthquakes, abnormal voltage or
other disasters;

- additions, modifications, disassembly, transportation, or repairs by any person

other than service technicians authorized by TOSHIBA TEC CORPORATION; or

- use of paper, supplies or parts other than those recommended by TOSHIBA

TEC CORPORATION.

4. Subject to paragraph 1, TOSHIBA TEC CORPORATION shall not be liable to Cus­tomer for:

- loss of profits; loss of sales or turnover; loss of or damage to reputation; loss of

production; loss of anticipated savings; loss of goodwill or business opportuni­ties; loss of customers; loss of, or loss of use of, any software or data; loss under
or in relation to any contract; or

- any special, incidental, consequential or indirect loss or damage, costs,

expenses, financial loss or claims for consequential compensation;

whatsoever and howsoever caused which arise out of or in connection with the
Product or the use or handling of the Product even if TOSHIBA TEC CORPORA­TION is advised of the possibility of such damages.

TOSHIBA TEC CORPORATION shall not be liable for any loss, cost, expense,
claim or damage caused by any inability to use (including, but not limited to failure,
malfunction, hang-up, virus infection or other problems) which arises from use of the
Product with hardware, goods or software which TOSHIBA TEC CORPORATION
has not directly or indirectly supplied

AS/400 Print Solution — Preface 7

Preface

The e-STUDIO520/600/720/850, e-STUDIO281C/351C/451C, e-STUDIO352/452,
e-STUDIO202L/232/282, e-STUDIO2500C/3500C/3510C, e-STUDIO165/205,
e-STUDIO167/207/237, e-STUDIO523/603/723/853, e-STUDIO353/453,
e-STUDIO203L/233/283, e-STUDIO2020C/2330C/2820C/2830C/3520C/3530C/
4520C, e-STUDIO5520C/6520C/6530C, e-STUDIO283C/353C/453C, e-STUDIO205L/
255/305/355/455, e-STUDIO555/655/755/855 and e-STUDIO182/212/242 provides
powerful network printing capability with many output finishing options. Now a means

exists to use the controller with an IBM AS/400

®

system.

About this guide

This guide is for network administrators who are familiar with the IBM AS/400 system. It
assumes you are familiar with the software applications used to print documents.

This guide is not designed for digital-copier service technicians or operators. For infor­mation on using and maintaining the equipment, refer to the following documents or
contact your dealer for support.

• e-STUDIO520/600/720/850, e-STUDIO281C/351C/451C, e-STUDIO352/452,

e-STUDIO202L/232/282, e-STUDIO2500C/3500C/3510C, e-STUDIO523/603/723/
853, e-STUDIO353/453, e-STUDIO203L/233/283 and e-STUDIO283C/353C/453C:

Operator’s Manual for Basic Functions

• e-STUDIO2020C/2330C/2820C/2830C/3520C/3530C/4520C, e-STUDIO5520C/

6520C/6530C, e-STUDIO205L/255/305/355/455 and e-STUDIO555/655/755/855:

Copying Guide

• e-STUDIO165/205, e-STUDIO167/207/237 and e-STUDIO182/212/242:

Operator’s Manual for Copying Functions

Conventions

• The term “equipment” in this manual refers to the following models:

- e-STUDIO520/600/720/850

- e-STUDIO281C/351C/451C

- e-STUDIO352/452

- e-STUDIO202L/232/282

- e-STUDIO2500C/3500C/3510C

- e-STUDIO165/205

- e-STUDIO167/207/237

- e-STUDIO523/603/723/853

- e-STUDIO353/453

- e-STUDIO203L/233/283

- e-STUDIO2020C/2330C/2820C/2830C/3520C/3530C/4520C

- e-STUDIO5520C/6520C/6530C

- e-STUDIO283C/353C/453C

- e-STUDIO205L/255/305/355/455

- e-STUDIO555/655/755/855

- e-STUDIO182/212/242

8 AS/400 Print Solution — Preface

AS/400 Print Solution — Table of Contents 9

Table of Contents

Software License Agreement ......................................................................... 3

Trademarks and Copyright ............................................................................. 5

Disclaimer Notice............................................................................................6

Preface ........................................................................................................... 7

About this guide ......................................................................................................7

Conventions ......................................................................................................7

Table of Contents ...........................................................................................9

1. AXIS Network Print Server ............................................................................11

Overview.......................................................................................................12

Components .........................................................................................................12

Finishing options and logical printers....................................................................13

Installation ....................................................................................................14

Installation procedure ...........................................................................................14

Configuration ................................................................................................17

Available AXIS firmware version...........................................................................17

Update procedure .................................................................................................17

Copier model ........................................................................................................19

Only PCL available ...............................................................................................20

Available finisher options ......................................................................................21

General settings....................................................................................................28

IPDS emulator ......................................................................................................29

Custom copier driver.............................................................................................31

Problem Solving ........................................................................................... 32

Problems and recommended solutions ................................................................32

Customer service..................................................................................................32

2. WorkStation Customization Object for TOSHIBA e-STUDIO .....................33

Overview.......................................................................................................34

Components .........................................................................................................34

Finishing options and logical printers....................................................................34

Installation ....................................................................................................35

Installation procedure ...........................................................................................35

Uninstallation ................................................................................................ 40

Uninstallation procedure .......................................................................................40

Operation...................................................................................................... 44

Operational procedure ..........................................................................................44

Print file script .......................................................................................................45

Appendix.......................................................................................................47

Stapling specifications ..........................................................................................47

Printing character size - Reference values ...........................................................48

Glossary..............................................................................................................49

Definitions of Terms...................................................................................... 49

10 AS/400 Print Solution — Table of Contents

AS/400 Print Solution — 1. AXIS Network Print Server 11

1. AXIS Network Print Server

12 AS/400 Print Solution — Overview

Overview

Components

The components of the AS/400® Printing Solution are:

• AS/400 server

• Your equipment

• USB cable to connect the AXIS 5570e Print Server and your equipment

• AXIS 5570e Print Server

• Client PC workstation

• Custom Config file (Config_landscape) TOSHIBA TEC Products

The configuration diagram illustrates the relationship among these components.

Print output generated by the AS/400 server passes through the AXIS 5570e Print
Server that acts as a converter from IPDS into PCL print commands, which are then
sent to your equipment. For more information about AXIS 5570e Print Server, go to the
AXIS COMMUNICATIONS of www.axis.com

.

A client PC can also send commands directly to your equipment.

AS/400 Server

AS/400 Printing Solution components

Client PC Client PC Client PC

Network HUB

AXIS 5570e
Print Server

USB

Connection

AS/400 Print Solution — Overview 13

Finishing options and logical printers

TOSHIBA offers several finishing options in addition to standard print commands com­ing from the AS/400. For example, stapling and hole punching are finishing options.

The finishing options are grouped in several preconfigured sets, which you associate
with up to eight logical printers.

NOTE:

• Any finisher options are not supported in e-STUDIO165/205 and e-STUDIO167/

207/237.

14 AS/400 Print Solution — Installation

Installation

Installation procedure

Install the AS/400 printing solution in two steps:

1. Set up the hardware

2. Set up the AS/400 printer

Step 1: Set up the hardware

NOTE: • The controller can be directly connected to the AS/400 network at the same time.

Thus, PCL-based or raw print jobs can be sent to it via the network, bypassing the
AXIS 5570e Print Server device.

1. Following the product installation instructions that came with

the AXIS 5570e Print Server, setup this device.

2. Connect the AXIS 5570e Print Server and your equipment

using the USB cable.

3. Press the TEST button on the AXIS 5570e Print Server to print

a test page to your equipment.

4. Connect the AXIS 5570e Print Server to the network hub.

AS/400 Print Solution — Installation 15

Step 2: Set up the AS/400 printer

On the AS/400, use the CRTDEVPRT command to configure the print settings accord­ing to the following table:

All other settings can be left unchanged.

NOTE:

• If you experience any problems, press F1 for help.

Sample AS/400 Printer Setup Screen

Configuring the AXIS 5570e

Follow the instructions below to configure your AXIS 5570e for AS/400 IPDS over PPR/
PPD printing using a standard Web browser:

1. Start a Web browser and enter the IP address or the host

name of the AXIS 5570e in the location field. Press Enter.
The internal Web pages of the AXIS 5570e will appear.

AS/400 Print settings

Setting Name Value

Device description Unique description, such as TOSHIBA

Device class *LAN

Device type *IPDS

Device model 0

LAN attachment *IP

Port number e.g. 5001

Font identifier 11

Remote location IP address of AXIS 5570e

16 AS/400 Print Solution — Installation

NOTE: • To protect the admin pages and the Configuration Wizard from unauthorized use,

enter a password (by default set to pass) in the Root Password field under Admin
General Settings.

• Use the same port number when creating the print device (page 15).

Note for IPDS printing:

2. Click the Configuration Wizard for IBM sessions button.

3. Delete the pre-configured PPR/PPD session. Pre-configured

session is not available for TOSHIBA e-STUDIO series.

4. Click the Add Session button. This will start the Configura-

tion Wizard which is a step-by-step guide through the
required configuration settings.

Verifying the communication link (AS/400)

Follow the instructions below to verify the communication to the AXIS 5570e:

1. Type WRKCFGSTS *DEV <Device description Name> on the

AS/400 command line and press Enter. The previously cre­ated printer device will be displayed. The status of the printer
device should be VARIED OFF.

2. Vary on the printer device by typing 1 in the Opt field. Press

Enter.

3. Press F5 to refresh the display. The printer device should

now be VARIED ON.

4. Start the printer writer by typing STRPRTWTR <Device

description Name> on the AS/400 command line.
Press Enter.

5. Press F5 to refresh the display. The printer device should

now be ACTIVE/WRITER.

6. Direct a printout to this printer device. A successful printout

verifies the communication link between the AS/400 and the
AXIS 5570e.

NOTE: • If the setup fails, refer to the troubleshooting section in the AXIS 5570e User’s Man-

ual, on www.axis.com

In the Configuration Wizard, you can choose between PCL or PostScript printing.
Choose PCL for Printer Driver. PostScript is not available.

AS/400 Print Solution — Configuration 17

Configuration

Available AXIS firmware version

Use the production release version or service release version given in the following
table when using TOSHIBA MFP.

All official firmware releases for the AXIS 5570e are available on AXIS website.

http://www.axis.com/techsup/prtsrv/axis_5570e/firmware.php

Use AXIS 5570e IPDS printing when using TOSHIBA MFP.

Update procedure

Update procedure of the AXIS 5570e firmware using FTP:

1. Open a Windows command prompt.

2. Connect to the print server using ftp: Type ftp <ip address>

3. Enter the user and password: (Default user: root Default

password pass) and press Enter.

4. Change to binary transfer mode: type bin and press Enter.

5. Type hash and press Enter.

6. Type put <filename> FLASH. A stream of hash marks will

appear.

7. The message "Transfer complete. Flash programming fin-

ished OK. " will appear.

TOSHIBA MFP Production release

version

Service release

version

e-STUDIO520/600/720/850 7.08 or later 7.06.04 or later

e-STUDIO523/603/723/853

e-STUDIO281C/351C/451C

e-STUDIO352/452 7.08 or later 7.08.2 or later

e-STUDIO353/453

e-STUDIO202L/232/282

e-STUDIO203L/233/283

e-STUDIO2500C/3500C/
3510C

7.10 or later 7.08.2 or later

e-STUDIO165/205

e-STUDIO167/207/237

e-STUDIO2020C/2330C/
2820C/2830C/3520C/3530C/
4520C

e-STUDIO5520C/6520C/
6530C

e-STUDIO283C/353C/453C

18 AS/400 Print Solution — Configuration

8. The print server will restart in five seconds running the new

software.

Update procedure of the config file:

1. Get the config file by FTP. Open a Windows command prompt

and enter the following:

ftp <ip address>
default user name root
default password pass
get config
bye

2. Update the custom driver parameters from the config file; the

parameters needed for the custom driver begin with DC Gen­eral Menu and end with DC PCL Copies.

3. Save the file as, e.g. my_template.

4. Upload 'my_template' to the print server by FTP.

ftp <IP address>
default user name root
default password pass
put my_template CONFIG
bye

AS/400 Print Solution — Configuration 19

Copier model

When printing portrait data, select an appropriate copier model, e.g. Toshiba
eSTUDIO520/600/720/850 or Toshiba eSTUDIO281C/351C/451C.

When printing landscape data, select Custom copier driver for Copier model.

 P.31 "Custom copier driver"

NOTE: • In using e-STUDIO167/207/237, choose e-STUDIO165/205.

• In using e-STUDIO523/603/723/853, choose e-STUDIO520/600/720/850.

• In using e-STUDIO353/453, choose e-STUDIO352/452.

• In using e-STUDIO2020C/2330C/2820C/2830C/3520C/3530C/4520C, choose

e-TUDIO2500C/3500C/3510C.

• In using e-STUDIO5520C/6520C/6530C, choose e-STUDIO2500C/3500C/3510C.

• In using e-STUDIO283C/353/453C, choose e-STUDIO281C/351C/451C.

20 AS/400 Print Solution — Configuration

Only PCL available

In the Configuration Wizard for IBM sessions, select PCL for Printer Driver. PostScript
is not available.

Edit Session:

Only PCL is available for IPDS Printer Driver under Edit Session. PostScript is not
available.

AS/400 Print Solution — Configuration 21

Available finisher options

The following options are available for the settings of Logical Printers or Edit Session.

Duplex:

Edit Session:

Long Edge Binding and Short Edge Binding are available for Duplex under Edit Ses­sion.

22 AS/400 Print Solution — Configuration

Logical Printers:

LONG_EDGE_BINDING and SHORT_EDGE_BINDING are available for Copier
Duplex under Logical Printers.

Staple:

Edit Session:

Top Left Slant, Top Double, Left Double and Top Right are available for Staple under
Edit Session.

Center is not available.

Selecting Center staples at the center of the paper, not in a book format.

AS/400 Print Solution — Configuration 23

Logical Printers:

TOP_LEFT_SLANT, TOP_RIGHT, TOP_DOUBLE and LEFT_DOUBLE are available
for Copier Staple under Logical Printers.

TOP_LEFT_HORIZONTAL, TOP_LEFT_VERTICAL, BOTTOM_LEFT,
BOTTOM_RIGHT and CENTER are not available.

Selecting CENTER staples at the center of the paper, not in a book format.

NOTE: • e-STUDIO165/205 and e-STUDIO167/207/237 are not supporting the Staple

Option.

24 AS/400 Print Solution — Configuration

Hole Punch:

Edit Session:

Long Edge and Short Edge are available for Hole Punch under Edit Session.

Logical Printers:

LONG_EDGE and SHORT_EDGE are available for Copier Hole Punch under Logical
Printers.

NOTE:

• e-STUDIO165/205 and e-STUDIO167/207/237 are not supporting the Hole Punch

Option.

AS/400 Print Solution — Configuration 25

Fold:

Fold option is not available.

Edit Session:

Logical Printers:

HALF_FOLD and Z_FOLD are not available for Copier Fold under Logical Printers.

26 AS/400 Print Solution — Configuration

Paper Source:

Default and 1-4 are available for Paper Source.

Default: Auto select
1: Upper Cassette
2: Lower Cassette
3: 1st Pedestal or Large Capacity Feeder
4: 2nd Pedestal

Edit Session:

AS/400 Print Solution — Configuration 27

Logical Printers:

5 is not available for Copier Paper Sources under Logical Printers.

Copies:

The Copies option is for selecting the number of copies.

28 AS/400 Print Solution — Configuration

General settings

Select DISABLE for Printer Information and Bidirectional control if extra data, which is
specified as "PAGECOUNT", is printed.

AS/400 Print Solution — Configuration 29

IPDS emulator

IPDS bin under the IPDS Configuration tab is used for setting the paper size.

Statement, Ledger, Folio, Hagaki, Letter, Legal, A4 and A3 are available.

Executive and Custom are not available.

NOTE: • Statement and Hagaki are not supported in e-STUDIO165/205 and e-STUDIO167/

207/237.

PostScript Page Size, PostScript Page Orientation, PostScript Page Format and Post­Script Page Font are not available under Logical Printers.

N-up under the IPDS Configuration tab is not available.

IPDS Configuration:

30 AS/400 Print Solution — Configuration

For PCL Bin number, the available value for TOSHIBA MFP is as follows:

1: Upper
2: Bypass
4: Lower
5: Pedestal Upper or Large Capacity Feeder
7: Auto
21: Pedestal Lower

AS/400 Print Solution — Configuration 31

Custom copier driver

When you print landscape data with some finisher options enabled, you may need to
use the Custom Copier Driver for correct output. Obtain the information about the Cus­tom copier driver functionality from AXIS COMMUNICATIONS web site. When you use
the Custom Copier Driver, select "config_landscape" for the PCL config setting.

NOTE:

• When you use the Custom copier driver, the printing condition is the same when

only PCL and available finisher options can be selected.

Select Custom copier driver for Copier under Edit Session.

Select Custom_copier_driver for Copier Model under Logical Printer.

32 AS/400 Print Solution — Problem Solving

Problem Solving

Problems and recommended solutions

The following table provides suggestions for resolving printing problems.

Customer service

For help with AXIS 5570e Print Server questions, go to the AXIS COMMUNICATIONS
section of www.axis.com.

Problem Recommended solution

The finishing option needed
for the current job did not
occur.

• Check the Custom Config file currently loaded

• Check if the print queue on the AS/400 is config-

ured to use the correct port for the logical printer
with the desired finishing option

Document does not print

• Make sure both the controller and the AXIS 5570e

Print Server are powered on and online

• Check the cable connection. Print a test page by

pressing the TEST button on the AXIS 5570e Print
Server

• Ensure both the controller and the AXIS 5570e

Print Server are configured with the TCP/IP proto­col

• Make sure the print queue on the AS/400 is con-

figured to use the current IP address of the AXIS
5570e Print Server. Remember, it is recom­mended that a static IP address is assigned to the
AXIS 5570e Print Server device

• Restart the controller and/or the AXIS 5570e Print

Server if necessary

AXIS 5570e Print Server can­not be discovered

• Check configuration according to AXIS 5570e

Print Server guide

• Make sure the AXIS 5570e Print Server is config-

ured with the TCP/IP protocol

AS/400 Print Solution — 2. WorkStation Customization Object for TOSHIBA e-STUDIO 33

2. WorkStation Customization Object
for TOSHIBA e-STUDIO

34 AS/400 Print Solution — Overview

Overview

Components

The components of the AS/400® Printing Solution are:

• AS/400 Server OS version 5.2 or later (The latest PTF is recommended)

• Your equipment (See NOTE below.)

• WorkStation Customization Object for TOSHIBA e-STUDIO

The configuration diagram illustrates the relationship among these components.

Print data generated with AS/400 can be printed out from a TOSHIBA MFP by relating
them with OUTQ which was set up with the WorkStation Customization Object for
TOSHIBA e-STUDIO.

NOTE: • The WorkStation Customization Object for TOSHIBA e-STUDIO does not support

the following models:

- e-STUDIO281C/351C/451C

- e-STUDIO2500C/3500C/3510C

Finishing options and logical printers

TOSHIBA offers several finishing options in addition to standard print commands com­ing from the AS/400. For example, stapling is a finishing option.

AS/400 Printing Solution components

Network HUB

AS/400 Server

AS/400 Print Solution — Installation 35

Installation

Installation procedure

Before installing the WorkStation Customization Object for TOSHIBA e-STUDIO, con­figure the system environments as follows:

• Set up AS/400 Server under the environment that allows you to use printing func-

tions.

• Set up a TOSHIBA MFP under an environment that allows you to use it in a net-

work.

• Connect the AS/400 Server and the TOSHIBA MFP with a LAN cable.

Step 1: Installing WorkStation Customization Object for TOSHIBA
e-STUDIO

This section describes how to install the WorkStation Customization Object for
TOSHIBA e-STUDIO.

1. Mount a product CD into a CD-ROM drive.

2. Login as a user with QSECOFR authority.

3. Execute a command [LODRUN] + [F4] and then specify the

CD-ROM drive where you mounted the product CD.

36 AS/400 Print Solution — Installation

4. The setting screen for OUTQ appears as the installation is

executed. Specify the name of OUTQ (maximum 7 bytes) to
be used, its library, the IP address of the printer and default
tray type*. Then press the execution key.

* default tray type

- e-STUDIO5520C/6520C/6530C
Enter “ I ” (InnerTray) or “S” (SideTray). If you use both of them, enter one, install
“WorkStation Customization Object for TOSHIBA e-STUDIO” and then register
the other when setting it up. For details of the setting up, see the following page:

 P.37 "Step 2: Setting up WorkStation Customization Object for TOSHIBA

e-STUDIO"

- Other models
Enter “ I ” (InnerTray).

5. The installation is completed.

• The installation is properly completed unless any error messages appear. You

can go to the following page because in this case the next step "Setting up
WorkStation Customization Object for TOSHIBA e-STUDIO" is also completed:

 P.38 "Step 3: Starting up auto assign (resident) program"

• An error message appears when the specified OUTQ name already exists or

OUTQ was not generated because a parameter value is in error.

• If an error message appears or you stopped the command by pressing [F12] or

[F3], go to the following page:

 P.37 "Step 2: Setting up WorkStation Customization Object for TOSHIBA

e-STUDIO"

AS/400 Print Solution — Installation 37

Step 2: Setting up WorkStation Customization Object for TOSHIBA
e-STUDIO

This section describes how to set up the WorkStation Customization Object for
TOSHIBA e-STUDIO.

1. Login as a user with QSECOFR authority.

2. Execute the command below to add a library "WTEC02" to

the top of the library list.

ADDLIBLE WTEC02

3. Execute a command [TECSETQ] + [F4]. Then specify the

name of OUTQ (maximum 7 bytes) to be used, its library, the
IP address of the printer and default tray type*. Then press
the execution key.

* default tray type

- e-STUDIO5520C/6520C/6530C
Enter “ I ” (InnerTray) or “S” (SideTray). If you use both of them, enter one, set
up “WorkStation Customization Object for TOSHIBA e-STUDIO” and then set it
up again for registering the other.

- Other models
Enter “ I ” (InnerTray).

4. The setup is completed.

• The setup is properly completed unless any error messages appear.

• An error message appears when the specified OUTQ name already exists or

OUTQ was not generated because a parameter value is in error.

• If an error message appears or you stopped a command by pressing [F12] or

[F3], execute the command [TECSETQ] + [F4] again.

38 AS/400 Print Solution — Installation

Step 3: Starting up auto assign (resident) program

This section describes how to start up auto assign (resident) program.

NOTE:

• It is recommended to load the auto assign (resident) program into IPL.

1. Login as a user with QSECOFR authority.

2. Execute the command below to add a library "WTEC02" to

the top of the library list.

ADDLIBLE WTEC02

3. Execute a command [STRTECPRT] + [F4]. Then select the

name of OUTQ that you specified at the installation or setup,
a job queue to use and its library. Then press the execution
key.

NOTE: • If you use a job queue and the library at their initial values, this program will run

within QBATCH.

AS/400 Print Solution — Installation 39

4. The program is started up.

• Execute a command [WRKACTJOB] to display the list. If the status of this pro-

gram is displayed as "DEQA" in the list, the program is properly started up.

• If the name of OUTQ to be monitored or a job queue to be used is incorrect, the

status of this program is displayed as "MSGW" in the list. In this case, confirm
the message and then execute the command [STRTECPRT] + [F4] again.

40 AS/400 Print Solution — Uninstallation

Uninstallation

Uninstallation procedure

Step 1: Uninstalling WorkStation Customization Object for
TOSHIBA e-STUDIO

1. Execute a command [WRKACTJOB] and then select a resi-

dent OUTQ monitoring program. Then enter option "4". Now
the resident program exits.

NOTE: • Turn the power of the printer to be used OFF before starting uninstallation; other-

wise the program will exit in the middle of the uninstallation.

AS/400 Print Solution — Uninstallation 41

2. Execute a command [DLTOUTQ OUTQ(library name / OUTQ

name

*1

)] to delete the OUTQ specified at the installation.

*1: It shall be the OUTQ name specified at the installation or the setup.

3. Execute a command [ENDWTR OUTQ name

*1

01*IMMED] to

disconnect the printer.

*1: It shall be the OUTQ name specified at the installation or the setup.

42 AS/400 Print Solution — Uninstallation

NOTE: • The part "01" after the OUTQ name shall be changed from "01" through "07" as you

repeat this command seven times.

4. Execute a command [WRKOUTQ OUTQ name

*1

*] to confirm

that no spool remains.

*1: It shall be the OUTQ name specified at the installation or the setup.

AS/400 Print Solution — Uninstallation 43

If "Files" is a value other than "0" and also there are remaining spools, select option "5"
to delete the remaining spools.

5. Execute a command [DLTLIB WTEC02] to delete the product

library.

44 AS/400 Print Solution — Operation

Operation

Operational procedure

Follow the procedure below to operate the WorkStation Customization Object for
TOSHIBA e-STUDIO.

1. Specify print file script (ORIENTATION, STAPLE, DUPLEX and

DRAWER) for a document to be printed with the MFP.

For the details of file script parameters, see the following page:

 P.45 "Print file script"

2. Change a job to alter the OUTQ specified at the installation or

the setup to the one for printing functions.

3. Start up the auto assign (resident) program.

For starting up, see the following page:

 P.38 "Step 3: Starting up auto assign (resident) program"

NOTE:

• Start up the resident program every time you execute IPL.

4. Perform routine work.

When you are performing routine work, you do not need to particularly pay atten­tion to this function.

5. Finish a job.

Finish a job in any of the following methods:

• Execute a command [WRKACTJOB]. Then select a job to be finished and select

Option "4". Then press the execution key.

• Execute a command [ENDSBS] and then exit the corresponding sub system.

NOTE:

• Turn the power of the printer to be used OFF before starting the operation; other-

wise the program will exit in the middle of the operation.

AS/400 Print Solution — Operation 45

Print file script

Specify print file script below according to the printing style of a document to be printed
with an MFP.

Example:

The examples of commands for print file script are as follows:

Portrait + DUPLEX SHORT_EDGE + STAPLE TOP_LEFT:

CHGPRTF FILE (library name / spool file name) DUPLEX(*TUMBLE) CORNER­STPL(*TOPLEFT)

Automatic drawer selection

In case of LT/A4, the orientation of the paper is reversed when "TOP_DOUBLE" and
"STAPLE" are selected together. Therefore the drawer in this case shall be selected as
follows:

LT/A4 (Portrait) + STAPLE TOP_DOUBLE:

DRAWER: LT-R/A4-R

LT/A4 (Landscape) + STAPLE TOP_DOUBLE:

DRAWER: LT/A4

Printing directions on the back side (DUPLEX)

The examples of printing directions on the back side of the paper in case of "DUPLEX"
are shown below.

Printing Style Attribute

ORIENTATION Portrait

Landscape

PAGRTT : *AUTO (Leave it default.)

Or select “0”

:90

STAPLE TOP_LEFT

TOP_RIGHT
LEFT_DOUBLE
TOP_DOUBLE

CORNERSTPL : *TOPLEFT

:*TOPRIGHT
: *BOTLEFT
: *BOTRIGHT

DUPLEX LONG_EDGE

SHORT_EDGE

DUPLEX : *YES

:*TUMBLE

Printing directions on the back
sides differ depending on the
orientation. See "Printing
directions on the back side
(DUPLEX)" on the next page.

DRAWER AUTO DRAWER : 1 (Leave it default.)

46 AS/400 Print Solution — Operation

LONG_EDGE: DUPLEX(*YES)

SHORT_EDGE: DUPLEX(*TUMBLE)

ABCD

EFG

Portrait

ABCD

EFG

Landscape

ABCD

E...

ABCD

EFG

ABCD

EFG

ABCD

EFG

ABCD

E...

ABCD

EFG

Portrait

Landscape

AS/400 Print Solution — Appendix 47

Appendix

Stapling specifications

*1: OUTQ numbers assigned by resident programs.

OUTQ*1

Printing Specifications Available Sizes

Remarks

Por-

trait/
Land­scape

STAPLE LT LG LD A3 A4 FO COM ST

1 xxxxxxx01 Portrait OFF 99999 9 9 9Rotational degrees PAGRTT =

*AUTO or 0

Land­scape

OFF 99999 9 9 9Rotational degrees PAGRTT = 90

2 xxxxxxx02 Portrait TOP_LEFT 99999 9 9 – Rotational degrees PAGRTT =

*AUTO or 0
Stapling position CORNERSTPL
= *TOPLEFT

3 xxxxxxx03 Portrait TOP_RIGHT 99999 9 9 – Rotational degrees PAGRTT =

*AUTO or 0
Stapling position CORNERSTPL
= *TOPRIGHT

Land­scape

TOP_LEFT 99999 9 9 – Rotational degrees PAGRTT = 90

Stapling position CORNERSTPL
= *TOPLEFT

4 xxxxxxx04 Portrait TOP_DOUBLE 9

LTR

999 9

A4R

99– Rotational degrees PAGRTT =

*AUTO or 0
Stapling position CORNERSTPL
= *BOTRIGHT

Land­scape

LEFT_DOUBLE 9

LTR

999 9

A4R

99– Rotational degrees PAGRTT = 90

Stapling position CORNERSTPL
= *BOTLEFT

5 xxxxxxx05 Portrait LEFT_DOUBLE 9LT––– 9A4– – – Rotational degrees PAGRTT =

*AUTO or 0
Stapling position CORNERSTPL
= *BOTLEFT

6 xxxxxxx06 Land-

scape

TOP_RIGHT 9999 9 9 9 – Rotational degrees PAGRTT = 90

Stapling position CORNERSTPL
= *TOPRIGHT

7 xxxxxxx07 Land-

scape

TOP_DOUBLE 9LT––– 9A4– – – Rotational degrees PAGRTT = 90

Stapling position CORNERSTPL
= *BOTRIGHT

48 AS/400 Print Solution — Appendix

Printing character size - Reference values

* All paper sizes noted “-R” are rotated in “PAGRTT (90)”.

Paper Size CPI Line Char. Remarks

LT CPI(10) 66 80

CPI(15) 66 120

LT-R CPI(10) 51 110

CPI(15) 51 163 Number of characters: 158

LG CPI(10) 84 80

CPI(15) 84 120

LG-R CPI(10) 51 140

CPI(15) 51 210 Number of characters: 204

LD CPI(10) 102 103 PAGRTT(0)

CPI(15) 102 120 PAGRTT(0)

LD-R CPI(10) 66 170

CPI(15) 66 255 Number of characters: 249

A3 CPI(10) 99 105 PAGRTT(0)

CPI(15) 99 157 PAGRTT(0)

A3-R CPI(10) 70 160

CPI(15) 70 240

A4 CPI(10) 70 72

CPI(15) 70 108

A4-R CPI(10) 49 110

CPI(15) 49 165

CO CPI(10) 84 101 PAGRTT(0)

CPI(15) 84 151 PAGRTT(0)

CO-R CPI(10) 61 140

CPI(15) 61 210

FO CPI(10) 77 72

CPI(15) 77 108

FO-R CPI(10) 50 130

CPI(15) 50 195

ST CPI(10) 51 55

CPI(15) 51 82

ST-R CPI(10) 33 85

CPI(15) 33 125

AS/400 Print Solution — Glossary 49

Glossary

Definitions of Terms

Term Definition

DLC Data Link Control, the data link layer protocol.

Duplex The process of printing on both sides of a sheet of paper.

Finishing option A feature provided by TOSHIBA printers and copiers for doing such things as

stapling and hole punching documents.

Gateway address The default address that provides a single point of entry to a network.

IP Address Internet Protocol address of a computer or server attached to a network.

PCL Printer Control Language, developed by Hewlett Packard.

Print stream The information the AS/400 sends to its printer port. This information includes

the text to be printed and various print commands for formatting the text and
graphics.

Subnet mask The method used for splitting IP networks into a series of subnets (subgroups).

50 AS/400 Print Solution — Definitions of Terms

DP-2090/2520/3000/3570/4570
DP-5550/6550/7550/8550
FC-2020C/2330C/2820C/2830C/3520C/3530C/4520C
FC-5520C/6520C/6530C
DP-1670/2070/2370
FC-2500C/3500C/3510C
DP-1650/2040
FC-281C/351C/451C
DP-5200/6000/7200/8500
DP-3540/4540
DP-2050/2340/2840
DP-1830/2120/2420
OME060055I0

2006 - 2010 TOSHIBA TEC CORPORATION All rights reserved

2-17-2, HIGASHIGOTANDA, SHINAGAWA-KU, TOKYO, 141-8664, JAPAN

Guidance for
AS/400 Print Solution

R060120B3909-TTEC

Ver09 2010-07