Toshiba e-Studio 907, e-Studio 1057, e-Studio 1207 Quick Start Manual

DIGITAL MULTIFUNCTIONAL SYSTEM

Quick Start Guide

BEFORE FIRST USE

BE SURE TO ASK YOUR AUTHORIZED TOSHIBA DEALER ABOUT THE WARRANTY THAT YOUR SELLING DEALER EXTENDS TO YOU. In order to assure you, the end-user, of warranty protection, Toshiba extends a limited warranty to each of its authorized dealers and, in turn, requires each of its authorized dealers to extend its own warranty to you on terms that are no less favorable than those given to the dealer by Toshiba. You should be aware, however, that Toshiba does not itself extend any warranties, either express or implied, directly to you, the end-user, and no one is authorized to make any

representations or warranties on behalf of Toshiba. Specically, TOSHIBA DOES NOT EXTEND TO YOU, THE END-USER,

ANY EXPRESS WARRANTY OR ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR USE OR FITNESS FOR ANY PARTICULAR PURPOSE IN CONNECTION WITH THE HARDWARE, SOFTWARE OR FIRMWARE EMBODIED IN, OR USED IN CONJUNCTION WITH THIS PRODUCT. Toshiba is not responsible for any damages or loss, either direct, incidental or consequential, which you, the end-user, may experience as a result of your purchase or use of the hardware,

software or rmware embodied in or used in conjunction with this Product. Your sole remedy, in the event that you encounter any difculties with this Product, is against the authorized dealer from which you purchased the Product.

e-STUDIO907/e-STUDIO1057/e-STUDIO1207 (DP-9077/DP-1057/DP-1207) Digital Multifunctional System

In the event that this authorized dealer does not honor its warranty commitments, please contact Toshiba America Business Solutions, Inc., so that Toshiba can try to help assure complete satisfaction of all the warranty rights to which you are entitled from the authorized dealer.

Toshiba America Business Solutions, Inc.

9740 Irvine Blvd. Irvine, CA 92618

Each instruction also covers the optional units used with these products.

California Proposition 65 Warning: USA-California only

This Product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.

NOTICE for users in the USA

Caution!

For complete electrical disconnection, pull out the main plug.

The socket-outlet shall be installed near the equipment and shall be easily accessible.

FOR YOUR RECORDS ...

To protect against loss or theft, record and retain for reference the machine’s serial number located at the lower left corner of the left side of the machine. Model Number Serial Number Date of Purchase Place of Purchase Authorized TOSHIBA Printer Service Department Number

Notice for Users in U.S.A.

EMC (this machine and peripheral devices)

WARNING:

FCC Regulations state that any unauthorized changes or modications to this equipment not expressly approved by the

manufacturer could void the user’s authority to operate this equipment.

Shielded interface cables must be used with this equipment to maintain compliance with EMC regulations.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

This machine contains the software having modules developed by Independent JPEG Group. Copyright© 1995-2007 Adobe Macromedia Software LLC. All rights reserved. This product uses "InstantBoot" provided by IT Access Co., Ltd., Japan.

PostScript is a registered trademark of Adobe Systems Incorporated.

SOFTWARE LICENSE

The SOFTWARE LICENSE will appear when you install the software from the CD-ROM. By using all or any portion of the software on the CD-ROM or in the machine, you are agreeing to be bound by the terms of the SOFTWARE LICENSE.

The explanations in this manual are based on American English and the North American version of the software. Software for other countries and regions may vary slightly from the North American version.

• The explanations in this manual assume that you have a working knowledge of your Windows or Macintosh computer.

• For information on your operating system, please refer to your operating system manual or the online Help function.

• The explanations of screens and procedures in this manual are primarily for Windows Vista® in Windows®

environments. The screens may vary depending on the version of the operating system.

• Considerable care has been taken in preparing this manual. If you have any comments or concerns about the manual, please contact your dealer or nearest TOSHIBA Service Department.

• This product has undergone strict quality control and inspection procedures. In the unlikely event that a defect or other problem is discovered, please contact your dealer or nearest TOSHIBA Service Department.

• Aside from instances provided for by law, TOSHIBA is not responsible for failures occurring during the use of the product or its options, or failures due to incorrect operation of the product and its options, or other failures, or for any damage that occurs due to use of the product.

Products that have earned the ENERGY STAR® are designed to protect the environment

through superior energy efciency.

The products that meet the ENERGY STAR

guidelines carry the logo shown above.

The products without the logo may not meet the ENERGY STAR

guidelines.

Warranty

While every effort has been made to make this document as accurate and helpful as possible, TOSHIBA TEC Corporation

makes no warranty of any kind with regard to its content. All information included herein is subject to change without notice.

TOSHIBA is not responsible for any loss or damages, direct or indirect, arising from or related to the use of this operation manual. © Copyright TOSHIBA TEC Corporation 2014. All rights reserved. Reproduction, adaptation or translation without prior written permission is prohibited, except as allowed under copyright laws.

Quick Start Guide (this document)

Features important safety notes, names of parts and components, information about the power-on procedure, operation overviews, information for people who manage the machine, and information about other aspects of this machine.

Read this section before using the machine for the rst

time.

Software Setup Guide (CD-PDF)

Explains how to install the various drivers needed when using this machine as a printer or network scanner. Refer to this document when using this machine from a computer. The Software Setup Guide can be found on the “Software CD-ROM”.

DIGITAL MULTIFUNCTIONAL SYSTEM

Software Setup Guide

User's Manual (PC)

Can be downloaded from the machine to a computer and viewed. Refer to this document to learn more about printer mode and settings mode, and to learn about the details of each type of mode.

Operation Guide (Built-in)

Can be viewed by touching the operation guide icon on the machine’s touch panel. When you are using this machine, use this document to see an overview of a particular mode or when you are having trouble operating the machine.

OPERATION MANUALS AND HOW TO USE THEM

Conrm the machine’s IP address

First, tap the [Settings] key on the home screen, and then tap [System Settings] → [List

Print (User)] in the left menu.

Next, tap the [Print] key in the [All Custom Setting List], and conrm the IP address in

the printed list.

Insert the machine’s IP address into the

address bar of your web browser to access the machine.

http://machine’s IP address/ User verication may be required depending on the

machine’s settings. Please check with the machine’s administrator to obtain the account information necessary for

verication.

Download the [User's Manual]

Click [Operation Guide Download] on the displayed page. Next, select the desired

language from the “Language to download” list, and then click the [Download] button.

Double-click on the downloaded le to display the User's Manual.

"BATTERY DISPOSAL"

THIS PRODUCT CONTAINS A LITHIUM PRIMARY MEMORY BACK-UP BATTERY THAT MUST BE DISPOSED OF PROPERLY. PLEASE CONTACT YOUR LOCAL DEALER OR AUTHORIZED SERVICE REPRESENTATIVE FOR ASSISTANCE IN DISPOSING OF THIS BATTERY.

This product utilizes a CR coin Lithium battery which contains a Perchlorate material. Special handling for this material may apply, California residents, See www.dtsc.ca.gov/hazardouswaste/perchlorate/

Others, consult local environmental ofcers.

Downloading the User's Manual

You can download the [User's Manual] by following the procedures below while the machine is connected to the network.

Symbols in this manual

To ensure safe use of the machine, this manual uses various safety symbols. The safety symbols are

classied as explained below. Be sure you understand the meaning of the symbols when reading the manual.

WARNING CAUTION

Indicates a risk of death or serious injury. Indicates a risk of human injury or property

damage.

CAUTIONS

If you notice smoke, a strange odor, or other abnormality, do not use the machine.

If used in this condition, re or electrical shock may result.

Immediately switch off the main power and remove the power plug from the power outlet. Contact your dealer or nearest TOSHIBA Service Department.

Do not use a ammable spray to clean the machine.

If gas from the spray comes in contact with hot electrical components or the fusing unit inside the machine, re or

electrical shock may result.

Do not make any modications to this machine.

Doing so may result in personal injury or damage to the machine.

Do not remove the machine casing.

High-voltage parts inside the machine may cause electrical shock.

Do not place a container of water or other liquid, or a metal object that might fall inside, on the machine.

If the liquid spills or the object falls into the machine, re or electrical shock may result.

If a thunder storm begins, switch off the main power and remove the power plug from the outlet to

prevent electrical shock and re due to lightning.

Do not look directly at the light source.

Doing so may damage your eyes.

Do not block the ventilation ports on the machine. Do not install the machine in a location that will block the ventilation ports.

Blocking the ventilation ports will cause heat to build up in the machine, creating a risk of re.

The fusing unit and paper exit area are hot. When removing a misfeed, do not touch the fusing unit and paper exit area. Take care not to burn yourself.

When loading paper, removing a misfeed, performing maintenance, closing the front and side covers, and inserting and removing trays, take

care that your ngers are not pinched.

WARNING

Handling precautions

Meaning of the symbols

CAUTION! HOT

PINCH POINT KEEP CLEAR

PROHIBITED ACTIONS

DO NOT DISASSEMBLE

MANDATORY ACTIONS

The machine includes the document ling function, which stores document image data on the machine's hard drive. Stored documents can be called up and printed or transmitted as needed. If a hard drive failure occurs, it will no longer be possible to call

up the stored document data. To prevent the loss of important documents in the unlikely event of a hard drive failure, keep the originals of important documents or store the original data elsewhere. With the exception of instances provided for by law, TOSHIBA TEC Corporation bears no responsibility for any damages or loss due to the loss of stored document data.

Wave length 788 nm +12nm / -13nm

Pulse times

e-STUDIO907: Normal paper mode (P/S = 420 mm/s) = 4.786 µs ± 0.020 µs / 7mm Heavy paper mode (P/S = 420 mm/s) = 4.786 µs ± 0.020 µs / 7 mm e-STUDIO1057/1207: Normal paper mode (P/S = 580 mm/s) = 3.470 µs ± 0.014 µs / 7 mm Heavy paper mode (P/S = 580 mm/s) = 3.470 µs ± 0.014 µs / 7 mm

Output power Max 2.5 mW (LD1+LD2+LD3+LD4)

Laser information

Caution

Use of controls or adjustments or performance of procedures other than those specied herein may result in hazardous

radiation exposure.

This Digital Equipment is CLASS 1 LASER PRODUCT (IEC 60825-1 Edition 2-2007)

SAFETY PRECAUTIONS

This Digital Equipment is rated Class 1 and complies with 21 CFR 1040.10 and 1040.11 of the CDRH standards. This means that the equipment does not produce hazardous laser radiation. For your safety, observe the precautions below.

• Do not remove the cabinet, operation panel or any other covers.

• The equipment’s exterior covers contain several safety interlock switches. Do not bypass any safety interlock by

inserting wedges or other items into switch slots.

CAUTIONS

Do not insert or remove the power plug with wet hands.

This may cause electrical shock.

When removing the power plug from the outlet, do not pull on the cord.

Pulling on the cord may cause damage such as wire exposure and breakage,

and may result in re or electrical shock.

If you will not use the machine for a long time, be sure to remove the power plug from the outlet for safety.

Be sure to connect the power cord only to a power outlet that meets the specied voltage and current

requirements.

Also make certain the outlet is properly grounded. Do not use an extension cord or adapter to connect other devices to

the power outlet used by the machine. Using an improper power supply may cause re or electrical shock.

* For the power supply requirements, see the name plate in the lower left corner of the left side of the machine.

Power notes

Installation notes

Do not install the machine in a location with poor air circulation.

A small amount of ozone is created inside the machine during printing. The amount of ozone created is not

sufcient to be harmful; however, an unpleasant odor may be noticed during large copy runs, and thus the machine should be installed in a room with a ventilation fan or windows that provide sufcient air circulation. (The

odor may occasionally cause headaches.)

Locations exposed to direct sunlight

Plastic parts may become deformed and dirty output may result.

Locations with ammonia gas

Installing the machine next to a diazo copy machine may cause dirty output.

Locations subject to vibration.

Vibration may cause failure.

Do not install the machine on an unstable or slanted surface. Install the machine on a surface that can withstand the weight of the machine.

Risk of injury due to the machine falling or toppling.

Be sure to connect the power cord only to a power outlet that meets the specied voltage and current

requirements. Also make certain the outlet is properly grounded. Do not use an extension cord or adapter to connect other devices to the power outlet used by the machine. Using an improper power supply may

cause re or electrical shock.

* For the power supply requirements, see the name plate of each machines and devices.

Near a wall

Be sure to leave the clearances shown right between the unit and the nearest wall or other surface. For easy maintenance, you should also leave the clearances shown right around the unit.

Locations that are excessively hot, cold, humid, or dry. (near heaters, humidiers, air conditioners, etc.)

The paper will become damp and condensation may form inside the machine, causing misfeeds and dirty output.

30cm

30cm 45cm

CAUTION

The machine includes a built-in hard drive. Do not subject the machine to shock or vibration. In particular, never move the machine while the power is on.

• The machine should be installed near an accessible power outlet for easy connection.

• Connect the machine to a power outlet which is not used for other electric appliances. If a lighting xture is connected to the same outlet, the light may icker.

WARNING

Do not throw a toner cartridge into a fire.

Toner may y and cause burns.

About consumables

Store a toner cartridge out of the reach of children.

WARNING

NAMES OF PARTS AND POWER INPUT

The machine has two power switches: The main power switch inside the front cover located in the lower left corner, and the [Power] button ( ) on the operation panel.

In some machine operating states, restarting using the [Power] button ( ) may not make the settings take effect. In this case, turn off the main power switch and then turn it on again.

Turning on the power

•

Turn the main power switch to the "

" position.

• After the main power indicator lights up green, press the [Power] button (

Turning off the power

Turn off the power by pressing the [Power] button ( ), then turn the main power switch to the "

" position.

Restarting the machine

In order for some settings to take effect, the machine must be restarted. Follow the message displayed on the touch panel to restart the system

(turn off the power by pressing the [Power] button (

) and then press it

again to turn the power back on).

• When turning off the main power switch, make sure that all indicators other than the main power are turned off.

• In the case of a sudden main power outage, turn the power for the machine back on and then turn it off in the correct order. If you turn off the main power switch or unplug the power cord while the indicator is lit up or blinking, the hard disk drive may be damaged or data may be lost.

•

Turn off both the [Power] button (

) and the main power switch and unplug the power cord if you suspect a machine failure, if there is a bad thunderstorm nearby, or before you move the machine.

• When you change a toner cartridge while the keyboard is installed, be sure to store it in the operation panel unit. If a toner cartridge is changed while the keyboard is pulled out, the cartridge may come in contact with the keyboard and cause damage.

Caution:

Main power indicator

Main power switch

[Power] button

Bypass-tray

Tray 5 (MX-LC12)

Tray 2

Tray 3

Keyboard

Operation panel

Saddle nisher

Front cover

Tray 1

Tray 4

Optional

Curl Correction Unit

USB connector (A type)

Automatic document feeder

Status Indicator

Toner tray

This screen appears rst. When you touch an icon, the corresponding screen appears.

Pressing the [Home Screen] button ( ) on the operation panel also displays this screen. * The screen may differ from the actual one depending on the model or customization.

HOME SCREEN

Double

tapping

Lightly tap the touch panel twice. Use this method to switch preview modes or enlarge a preview image.

Flicking

Flick the panel to scroll a preview image.

Tapping

Touch and then quickly release the nger.

Use this method to select a key, tab or checkbox.

Long touching

Touch the key with your nger and hold it for

a while.

Dragging

Drag (slide your nger touching the panel

in a random direction) to replace or delete pages in the original displayed on the preview screen.

Sliding

Slide the scroll bar (with your nger touching

the panel) to scroll up and down a list containing a large number of items.

Operating the touch panel

In addition to the conventional method of single tapping, the touch panel of the machine can be operated by long touching, icking and sliding.

Network Folder

The scanned document is sent to the computer network

folder specied in the Windows network.

Copy

The scanned document is printed.

Operation Guide

See this document when you need help to use the machine.

Job Status

Tap this icon to check the status of the job currently

being executed.

Page switch keys

Use these keys to view a hidden page in the scrolling area.

Action panel

Tap an item to edit Home Screen or other operation.

Settings

In setting mode, various settings can be congured to suit

the aims and needs of your application.

E-mail

A scanned document is attached to an e-mail and sent.

HDD File retrieve

The scanned document is saved on the hard disk drive of the machine or an external memory device. This icon can also be tapped to edit or operate the stored data.

FTP

The scanned document is sent to the specied FTP server directory or the specied folder in a computer

connected to the network.

Scrolling area

Up to 12 icons are displayed. You can view hidden icons by scrolling the screen horizontally.

Fixed area

Up to 10 icons are always displayed.

PRINTER

Basic printing



In a Windows environment

This section explains how to print a document from "WordPad", which is a standard accessory application in Windows.

Select [Print] from the [File] menu

Select the printer driver for the machine and click the [Preferences] button

Click the [Paper] tab and select the paper size

Click the [OK] button to start printing

* Make sure the paper size is the same

as the paper size set in the application.



For Mac OS X environments

The following example explains how to print a document from the standard accessory application "TextEdit" in Mac OS X.

Select [Page Setup] from the [File] menu and select the printer

Congure paper and click

the [OK] button

Select [Print] from the [File] menu. Make sure that the correct printer is selected.

Print settings

Click the [Print] button to start printing

• Different types of paper sheets can be inserted for covers, etc.

• For Windows environments, different paper can be inserted into the specied

page, or the paper can be inserted as inserts.

COPY

Paper Select

Auto

Paper Select

8 X11

1 2

Plain

Paper Tray

8 X11

1 2

Plain

8 X11

1 2

Plain

8 X11

1 2

Plain

Tray 1/Tray 2/Tray 3/Tray 4

8 X11

1 2

Bypass Tray

Type and Size

Plain

Bypass Tray (Optional) Specify the type and size of paper.

8 X11

1 2

Plain

Large Capacity Tray

Large Capacity Tray (Optional)

Output

Middle

tray

Outputs to the middle tray of the machine

Offset

Tray

Outputs to the offset tray of the nisher

Sort

Outputs by sorting on a set basis

Group

Outputs by sorting on a page basis

Separator

Page

Inserts separator pages for every specied

number of copies

Top Tray

Outputs into the top tray (option)

Stacker Tray

Outputs into the stacker tray (option)

Multi Shot

Off

Multi Shot

Copying a multi-page original to a single sheet

Copy Ratio

100%

Copy Ratio

Zoom

Displays the basic ratio menu.

XY Zoom

Displays the XY Zoom ratio menu.

Auto Image

Automatically sets the ratio based on the original settings and paper settings.

11x17->8 1/2x11 8 1/2x11->5 1/2x8 1/2

64%

11x17->8 1/2x14 8 1/2x14->8 1/2x11

77%

8 1/2x14->11x17

121%

8 1/2x11->11x17 5 1/2x8 1/2->8 1/2x11

129%

Sets the ratio based on the original settings and paper settings.

( 25㨪200 ) %

100

Enlarges or reduces the image in increments or decrements of 1%

Other Ratio

Transits to the "Other Ratio" screen

by Paper

Transits to the "by Paper" screen

by Size

Transits to the "by Size" screen

2-Sided Copy

1-Sided->1-Sided

2-sided copy

1-Sided->1-Sided

1-sided copy

1-Sided->2-Sided

Outputs two 1-Side original sheets to one 2-Side sheet

2-Sided->2-Sided

Outputs one 2-Side original sheet to one 2-Side sheet

2-Sided->1-Sided

Outputs one 2-Side original sheet to two 1-Side sheets

Copy settings

Basic operations

Place the original

Copy settings

Preview

Set the number of copies

Start

Corrects the number of copies

1 Copy settings 2 Displays the [Function Review] dialog 3 Scans the original and displays it in the preview area (if preview is required) 4 Cancels all settings

Exposure

Auto

Exposure

Auto

Selects automatically

Photo

Best for photo originals

Text

Best for text originals

Map

Best for maps containing ne text

Text/Printed Photo

Prioritizes the quality of text and printed photo images

Light Original

Best for faint colored originals such as those written using pencil

Text/Photo

Best for text originals to which photos are pasted

1 . . . 3 . . . 5

Tap a darker or lighter area to adjust shading

Printed Photo

Prioritizes the quality of photo images

Original

Auto 8

x11

1 2

Original

Auto

Selects automatically

Inch

Displays inch size list

Displays AB size list

Direct Entry

Displays the direct entry screen

Custom Size

Displays the custom size list

Inch AB

51/2×81/

51/2 x 81/2 R A5 A5R B5 B5R

81/2×11 81/2 x 11R A4 A4R B4 A3

81/2×13 81/2×14 216 × 340 216×343

11×17 81/2×132/

Others

Margin Shift

Adds margins

Erase

Specify the edge erase (center erase) and erase width of the original for copies

Pamphlet Copy

Arranges a pamphlet format

Covers/Inserts

Inserts cover or insertion sheets

Transparency Inserts

Outputs transparency lms in a way that they do not

stick together

Blank Page Skip

Skipping blank pages in an original

Card Shot

Copies both sides of a card as a single page

Position Image

Specify the image print position

Tab Copy

Copies captions onto tab paper

Dual Page Copy

Copies each facing page

Book Copy

Copies a pamphlet

Book Divide

Splits a pamphlet original by page in a copy

Stamp

Prints dates, the number of pages, and stamps

Custom Image

Adds a registered image to an original

Hidden Pattern Print

Padding unauthorized copy deterrent data

Repeat Layout

Repeats the same image on one sheet in a copy

Multi-Page Enlargement

Making a poster-sized copy

Mirror Image

Inverts the original into a mirror image

Full Bleed Copy

Copies originals with no edge cut-off

Centering

Copying in the center of the paper

B/W Reverse

Reverses white and black

Job Build

Copies many originals at once

Tandem Copy

Using two machines to copy in parallel

Original Count

Check the number of scanned document sheets

Reverse Order

Copies originals in reverse order

Mixed Size Original

Copies originals of different sizes together

Slow Scan Mode

This mode switches document feeder controls for originals with thin paper thickness

Sharpness

Adjust the sharpness of an image

Scan Resolution

Specify the resolution of the original

Suppress Background

Suppresses light background area in copies

Toner Save Mode

Reduces toner consumption during copying *

File

Uses document lingdrive of the machine

Quick File

Temporarily saves the scanned data on the hard disk drive of the machine

* Items may not be displayed depending on the machine settings.

COPY

SCAN

Address Book

Tap this to display the address book screen to select a destination.

Tap this to switch between To and Cc.

Searches a destination

Resolution

200x200dpi

Resolution

100x100dpi 300x300dpi

100 x 100 dpi 150 x 150 dpi 200 x 200 dpi 300 x 300 dpi 400 x 400 dpi 600 x 600 dpi

150x150dpi 400x400dpi

200x200dpi 600x600dpi

Touch to input Address

Touch to input

Address

Enter an address directory.

Subject

Select a subject or enter it directly.

File Name

Select a le name or enter it directly.

Exposure

Auto

Exposure

Auto

Selects automatically

1 . . . 3 . . . 5

Touch a darker or lighter area to adjust shading

Text

Best for text originals

Text/Printed Photo

Prioritizes the quality of text and printed photo images

Text/Photo

Best for text originals to which photos are pasted

Printed Photo

Prioritizes the quality of photo images

Photo

Best for photo originals

Map

Best for maps containing ne text

Basic Operations (Scan to E-mail)

Place the original

Scan settings

Preview

Specify the destination

Start

1 Scan settings 2 Displays the [Function Review] dialog 3 Scans the original and displays it in the preview area (if preview is required) 4 Cancels all settings

Scan settings

SCAN

File Format

PDF

File Format

This function sets the le format and compression mode (ratio) of send data.

File format Compression mode Number of pages setting

TIFF

XPS

JPEG

PDF

PDF/A

Color/Grayscale B/W

Low

Middle

High

Bk Letter Emphasis

None

MH (G3)

MMR (G4)

Color/Grayscale B/W Color/Grayscale/Black & white

Transmittable formats: TIFF, XPS, JPEG, PDF, PDF/A

Transmittable formats: TIFF, XPS, PDF, PDF/A

Compressible modes: Low, Medium, High, Bk Letter Emphasis

Compressible modes: None, MH (G3), MMR (G4)

Specified Pages per File

Specify the number

of pages per le

Encry.

Creates an encrypted PDF

le

Encry.

Creates an encrypted PDF

le

Compact

Sends data by reducing its size

( 1㨪99 ) Page

Displays the number

of pages per le

U-Fine

Sends data by reducing its size but without reducing the image quality

Increases or decreases the number of pages per

le

Others

Job Build

Tap this to switch the job build mode on or off.

Setting it to On scans a large number of originals in segments.

Slow Scan Mode

Scans a thin original

Mixed Size Original

Scans originals of different sizes together

Original Count

Tap this to switch the original count setting on or off. Setting it to On checks the scanned number of original sheets.

Erase

Specify the edge erase (center erase) and erase width of the original to be sent

Dual Page Scan

Scans an original as two separate pages

Book Divide

Sends a pamphlet original by splitting it by page

Card Shot

Sends both sides of a card as a single page

Timer

Automatically performs transmission at the

specied time

Verif. Stamp

Stamps scanned documents

Suppress Background

Scans originals by suppressing light background area

Blank Page Skip

Erases blank pages mixed in an original after scanning

Drop Out Color

Removes chromatic colors from the scanned document before transmission

Sharpness

Adjust the sharpness of an image to produce a

sharper or softer image.

Contrast

Adding contrast to the scanned document before transmission.

File

Saves the send data on the hard disk drive of the machine.

Quick File

Temporarily saves the send data on the hard disk drive of the machine

DOCUMENT FILING

This function saves the original scanned on the machine or print data from a PC on the hard disk drive of the machine or on an external memory device.

The saved data can be printed or sent. Editing of the stored les, for example combining, is also possible.

Basic operations

HOME SCREEN

Select the folder

Place the original

Start

The usage of the machine's hard disk drive is displayed in graphical format, separately for Main Folder, Custom Folder, and Quick File Folder.

• Files stored using [Quick File] are provided with the "Sharing" property that can be accessed by any person for output and sending. Therefore, do not store sensitive documents or documents that you do not want to be used by others using the [Quick File] function.

Saves les temporarily.

Use this to save the original you wish to share among users.

Use this button to reset all settings.

Quick File Folder

Main Folder

Reset button

Displays the private screen for the login user.

My Folder

The folder for the registered user.

Custom Folder

HDD Status

Folder select screen

DOCUMENT FILING

You can select the method to display les. List view or thumbnails view can be selected.



Viewing by folder



Viewing by job

Choose Print Settings

Prints a le from the reprint screen This item changes to [Print] when multiple les are selected.

See Detail Information

Views property change and le detail information This item is not displayed when multiple les are selected.

Send

Sends a le from the resend screen This item is not displayed when multiple les are selected.

Print and Delete the Data

Select this item if you wish to delete data after printing.

Move

Moves a le You can also edit the le name using this option.

Prints the selected le immediately

Combine File

Merges the selected two les into a single le This item is not displayed when only one le or three or more les are selected.

Delete

Deletes data

Check Image

Check the content of the original le by image This item is not displayed when multiple les are selected.

Job settings menu

Select a le you wish to retrieve, then select a desired operation. The following operations are displayed on the action panel.

The [Print Now] operation is not displayed on the action panel but displayed as a button in the trigger area.

File list view File thumbnails view

Congure the output settings for copies using Sort, Group, Offset, Staple, Punch, or Fold.

Basic operations

Select [Output]

Copy output settings

Check the preview image

Start

1 Specify the output tray 2 Select the output and paper output type 3 Specify the details of output mode

COPY OUTPUT

Output tray settings

Specify the destination to output copies. The output tray currently selected is indicated by an arrow.

(When a nisher (50-sheet stapling) or saddle nisher (50-sheet

stapling) is installed)

The [Top Tray] key can be selected.

(When a nisher (100-sheet stapling) or saddle nisher

(100-sheet stapling) is installed)

The [Middle Tray] key can be selected.

When a large capacity stacker is installed

You can select the [Top Tray] key or [Stacker Tray] key.

Offset

Tray

Outputs to the offset tray

Offset

Offset function

Select this function when you wish to output copies while shifting them set by set. Selecting the staple function clears the Offset checkmark automatically.

Separator

Page

Separator Function

You can insert separator pages for every specied number of copies or before or after each job.

Sort/Group function

This function sets the sorting method when copying a scanned document.

Sort

Sorts the scanned document on a set basis, and outputs them

Group

Groups the scanned document on a page basis, and outputs them.

Sort staple

This function staples the output copies and deliver them to the tray.

1 staple in back

1 staple in front

2 Staples

Saddle Stitch

Copies can be folded at the center, stapled, and output. This function is only available when a saddle

nisher is installed.

Slant Staple

Enables slant stapling. This function is available when [1 Staple at

Back] is selected while a nisher (50-sheet stapling) or saddle nisher (50-sheet stapling)

is installed.

Output tray settings

COPY OUTPUT

Saddle Stitch

(When a saddle nisher is installed)

Copies can be folded at the center, stapled, and output.

(When a trimming module is installed on the saddle nisher)

For saddle folding, it trims a side drop, offering a good-looking output image.

2-Sided

Scanning 2-Sided originals

Cover Setting

Tap this to switch the cover setting Off or On, or to

congure the paper tray settings.

Off

Releases saddle stitch

1-Sided

Scans 1-Sided originals

Left Binding

This selects left binding

Right Binding

This selects right binding

Trimmer

Setting

Trimmer Setting

(When a trimming module is installed on the saddle nisher)

Enabling "Saddle Stitch" allows you to congure the trimmer

settings.

Off

Turns off the trimmer setting

Turns on the trimmer setting

( 2.0㨪20.0 ) mm

Specify the trimming width within the range of 2.0 to

20.0 mm

Punch function

(When a punch module is installed)

This function punches copies and outputs them. It is available for paper sizes 8-1/2

x11"R to 11"x17".

2 Hole Punch

3 Hole Punch

Punches holes during output

Folding function

(When a saddle nisher or folding unit is installed)

Copies can be folded and output.

Saddle

Fold

Selects saddle fold

Z-Fold

Selects Z-fold

C-Fold

Selects C-fold

Accordion Fold

Selects accordion fold

Double

Fold

Selects double fold

Half Fold

Selects half fold

Detail setting screen for each folding type

Inside

Folds paper so that the print side faces downward during output

A3 B4 A4R

8 X11R

1 2

11 X178 X14

1 2

Select the size of paper to be folded with Z-fold (One of either 11" x 17", 8-1/2" x 14", 8-1/2" x 11"R, A3, B4 and A4R can be selected)

Outside

Folds paper so that the print side faces upward during output

Fold Multiple Sheets Together

Select this option to fold multiple sheets together

Open Left

Folds paper for left binding during output

Original Image Output Image

Displays a folding image

Open Right

Folds paper for right binding during output

MANUAL FINISHING

This function allows you to set for nish on copied or printed pages. You can select the manual nishing mode if the inserter is installed. When the nisher, saddle nisher, punch module, or folding unit is installed, nishing operations, such as stapling, punching or folding, can be performed.

Basic operations

Place the original

Switch to the manual nishing

mode

Finishing method settings

Start



Changing modes from the Home

Screen



Changing modes from the screen

for each mode

Adjust the inserter tray guide to the paper size, and load paper. (Special media such as transparency

lm and tab paper cannot be used.)

1 Select the appropriate nishing method 2 Change the paper tray or output tray as

required

Middle

tray

Offset

Tray

Checking and changing

the output tray

The output tray is automatically selected based on the output function you set. If Z-Fold, Half Fold, or Punch is selected, however, you can select the middle or offset tray for the output tray. If you have changed the output tray, the output function may be deselected depending on the original output settings.

Middle

tray

Selects the middle tray as the output tray

Offset

Tray

Selects the offset tray as the output tray

Orientation of placed original

For stapling or punching on the desired position, place the paper as shown in the following:

• For staple function, place the paper face up and align text with the direction of the touch panel display. (For the saddle stitch function, place the paper so that middle surface faces up.

• When using punch or folding function, place the paper face up, and align text horizontally and upward with the scan (right) direction.

Upper

Tray

Plain

x11

1 2

Lower

Tray

Plain

8 x11

1 2

Checking and changing

the output tray

You can check the type and size of paper loaded.

As needed, the paper type and size can be specied for each of the

upper and lower trays. If you wish to change the paper sizes or types, select [System Settings] > [Paper Tray Settings] > [Inserter].

Plain

8 x11

Check the paper type and size

Upper

Tray

Selects the upper tray as paper tray

Lower

Tray

Selects the lower tray as paper tray

Paper Loading and Output Settings

MANUAL FINISHING

Staple

(When a nisher installed)

This function staples the loaded paper sheets into a sheaf.

1 staple in back

1 staple in front

2 Staples

Saddle Stitch

(When a saddle nisher is installed)

This function staples each set of copies at two positions in the center of paper, folds them in half, and outputs them.

(When a trimming module is installed on the saddle nisher)

For saddle stitch, it trims a side drop, offering a good-looking output image.

Saddle

Stitch

Staples each set of copies at two positions in the center of paper, and folds them in half during output

Trimmer

Setting

Trims a side drop for saddle folding during output Specify the trimming width within the range of

2.0 to 20.0 mm

Punch function

(When a punch module is installed)

This function punches holes in paper. It is available for paper sizes 8-1/2"x11"R to 11"x17".

You cannot use 12" x 18" (A3W) size paper, and special media such as transparency lm.

2 Hole Punch

3 Hole Punch

Punches holes during output

This function can be used with the Z-Fold function if a folding unit is attached to a nisher (100-sheet stapling) or saddle nisher (100-sheet stapling) while the paper size is 11” x 17”, or A3, B4.

Folding function

(When a folding unit is installed)

This function folds paper in Z-fold, C-fold, or other types of shapes.

(When a saddle nisher is installed)

Paper can be folded in a saddle fold.

The paper sizes that can be selected vary depending on the type of paper fold.

Special media such as transparency lm and tab paper cannot be

used.

Saddle

Fold

Allowable paper sizes: 12"x18", 11"x17", 8-1/2"x14", 8-1/2"x11"R, 8K, A3W, A3, B4, A4R, SRA3

The fold settings can be congured in [Detail]. B5R can be used only in a saddle nisher

(50-sheet stapling).

Z-Fold

Allowable paper sizes: 11"x17", 8-1/2"x14", 8-1/2"x11"R, A3, B4, A4R This function can be used with the staple and punch functions if a folding unit is installed in a

nisher (100-sheet stapling) or saddle nisher

(100-sheet stapling) while the paper size is 11” x 17”, or A3, B4.

C-Fold

Allowable paper sizes: 8-1/2”x11”R, A4R

Accordion Fold

Allowable paper sizes: 8-1/2”x11”R, A4R

Double

Fold

Allowable paper sizes: 8-1/2”x11”R, A4R

Half

Fold

Allowable paper sizes: 8-1/2”x11”R, A4R

Copies/Pages

Setting the number of

copies (number of pages)

This function loads previously sorted sheets and outputs multiple sets at once.

Number of copies setting

(1-999)

Enter the number of output copies (from 1 to 999)

Number of pages setting

All Pages

Select this to set all pages as one set

If this setting is enabled, set the [Number of Copies] to "1".

Manual

Select this to specify the number of page for each set

(1-200)

Enter a numeric value when [Manual] is selected. (from 1 to 200 pages)

Middle

tray

Offset

Tray

Checking and changing

the output tray

Middle

tray

Selects the middle tray as the output tray

Offset

Tray

Selects the offset tray as the output tray

SPECIFICATIONS

Name e-STUDIO907/e-STUDIO1057/e-STUDIO1207

Type Console

Color Monochrome

Copier system Laser electrostatic copier

Resolution

Read: 600 × 600 dpi, 600 × 400 dpi, 600 × 300 dpi Write: 600 × 600 dpi, 1,200 × 1,200dpi

Gradation Read: equivalent to 256 levels / Write: equivalent to 256 levels

Original paper sizes

Max. 11" × 17” (A3) for sheets and bound documents

Copy sizes

12" × 18" (A3 wide) to 5-1/2" × 8-1/2"R, A5R, Transparency lm, Heavy paper

Tray 1: 8-1/2" x 11", A4, B5 Tray 2: 8-1/2" × 11", A4 Tray 3: 12" × 18" (A3 wide), 11" × 17", 8-1/2" × 14", 8-1/2" × 13-1/2", 8-1/2" × 13-2/5", 8-1/2" × 13", 8-1/2" × 11", 8-1/2" × 11"R, 7-1/4 × 10-1/2"R, A3, B4, A4W, A4, A4R, B5, B5R Tray 4: 12" × 18" (A3 wide), 11" × 17", 8-1/2" × 14", 8-1/2" × 13-1/2", 8-1/2" × 13-2/5", 8-1/2" × 13", 8-1/2" × 11", 8-1/2" × 11"R, 7-1/4 × 10-1/2"R, 5-1/2" × 8-1/2"R, A3, B4, A4W, A4, A4R, B5, B5R, A5R

Warm-up time

210 seconds



This may vary depending on the ambient conditions.

First-copy time

e-STUDIO907: 4.0 seconds e-STUDIO1057: 3.2 seconds e-STUDIO1207: 3.2 seconds



This may vary depending on the state of the machine.



Portrait feeding of 8-1/2" x 11" (A4) sheets.

Continuous copying speeds* (when shifter is not in operation)

e-STUDIO907 e-STUDIO1057 e-STUDIO1207 8-1/2" × 11", A4, B5: 90 copies/min. 105 copies/min. 120 copies/min. 8-1/2" × 11"R, 7-1/4" × 10-1/2"R, A4R, B5R: 58 copies/min. 67 copies/min. 76 copies/min. 8-1/2" × 14", B4: 50 copies/min. 58 copies/min. 66 copies/min. 11" × 17", A3: 47 copies/min. 52 copies/min. 54 copies/min. * Continuous speed for same original source. Output may be temporarily interrupted to stabilize

image quality.

Copy ratios

Same size: 1:1 ± 0.8 % Enlarge: 121 %, 129 %, 200 %, 400 % Reduce: 25 %, 50 %, 64 %, 77 % Zoom range: 25 to 400 % (25 - 200 % using DSPF) in 1 % increments, total 376

increments. Can calculate zoom rate when mm is specied.

Useable paper

Tray 1: 16 lbs bond to 28 lbs bond (60 to105 g/m

)

Tray 2: 16 lbs bond to 28 lbs bond (60 to105 g/m

)

Tray 3: 16 lbs bond to 80 lbs cover (60 to 220 g/m

)

Tray 4: 16 lbs bond to 80 lbs cover (60 to 220 g/m

)

Paper feed / capacity

1,200 plus 800 plus 500 plus 500 ( = 3,000) sheets in 4 trays



Using 21 lbs (80

g/m

) weight paper

Max. paper feed / max. capacity

1,200 plus 800 plus 500 plus 500 ( = 3,000) sheets in 4 trays plus 500-sheet multi-bypass tray plus 5,000 sheets in large capacity trays plus 5,000 sheets in large capacity trays (total 13,500 sheets)



Using 21 lbs (80

g/m

) weight paper

Continuous copy Max. 9,999 copies

Memory

Standard: 5 GB HDD: 1 TB SD card: 4GB



1 GB = One billion bytes when referring to hard drive capacity. Actual format capacity is less.

Ambient environment

Operating environment

54 °F (10 °C) to 91 °F (35 °C) (20 % to 85 % RH) (Humidity is 60% or below while the temperature is 91°F (35°C), and the temperature is 86°F (30°C) or below while the humidity is more than 85%.) 590 - 1,013 hpa

Standard environment

68 °F (20 °C) to 77 °F (25 °C) (65 ± 5 % RH)

Required power supply

AC 208-240V/15A, 60Hz Power consumption Max. 3.55 kW

Dimensions

42-43/64" (W) × 31-3/32" (D) × 48-11/16" (H) (1,084 mm (W) × 790 mm (D) × 1,237 mm (H)) (When the operation panel is set to the default position)

Weight Approx. 651 lbs (295 kg)

Overall dimensions

48-13/16" (W) × 34-9/16" (D) (1,240 mm (W) × 878 mm (D))

Basic Specications / Copier specications

Name Duplex Single Pass Feeder (DSPF)

Document feeder types Duplex Single Pass Feeder (DSPF)

Original paper sizes 11" × 17" (A3) to 5-1/2" × 8-1/2" (A5)

Original paper types

Paper weight Thin paper 10 lbs bond (38 g/m

) to 13 lbs bond (49 g/m2)

Plain paper 13 lbs bond (50 g/m

) to 110 lbs index (205 g/m2)

Two-sided 13 lbs index (52 g/m

) to 110 lbs index (205 g/m2)

Paper storage capacity

250 sheets (21 lbs (80 g/m

))

(or maximum stack height of 1-9/32" (32.5 mm))

Scan speed (copy)

120 one-sided sheets/minute (8-1/2" × 11" (A4) horizontal) (600 × 300 dpi)

Automatic document feeder (Standard equipment)

Name Multi Bypass Tray (MX-MFX1)

Paper sizes 12" × 18" to 5-1/2" × 8-1/2"R (A5R)

Useable paper 16 lbs bond to 110 lbs cover (52 to 300 g/m

)

Paper capacity 100 sheets (21 lbs (80 g/m

))

Dimensions

When paper tray is closed 4-39/64" (W) × 19-61/64" (D) × 16-7/64" (H) (117 mm (W) × 507 mm (D) × 409 mm (H)) When paper tray is pulled out 14-11/16" (W) × 19-61/64" (D) × 16-7/64" (H) (373 mm (W) × 507 mm (D) × 409 mm (H))

Weight 16.5 lbs (7.5 kg) or less

Multi Bypass Tray

Name Large Capacity Tray

Paper sizes 8-1/2" × 11", A4, B5

Useable paper 16 lbs bond to 80 lbs cover (60 to 220 g/m

)

Paper capacity 3,500 sheets (21 lbs (80 g/m

))

Dimensions

14-13/16" (W) × 22-43/64" (D) × 20-5/8" (H) (376 mm (W) × 576 mm (D) × 524 mm (H))

Weight Approx. 63 lbs (28.5 kg)

Required power supply

Supplied from the machine

Name Large Capacity Tray

Paper sizes 12" × 18" (A3W) to 8-1/2" × 11"R

Useable paper 16 lbs bond to 80 lbs cover (60 to 220 g/m

)

Paper capacity 3,000 sheets (21 lbs (80 g/m

))

Dimensions

26-3/8" (W) × 22-7/16" (D) × 20-43/64" (H) (670 mm (W) × 570 mm (D) × 525 mm (H))

Weight Approx. 110 lbs (50 kg)

Required power supply

Supplied from the machine

MX-LC12 MX-LCX3 N

Large Capacity Tray

Name Large Capacity Trays

Paper sizes 12" × 18" (A3W) to 8-1/2" × 11" (B5R) ,SRA3, SRA4

Useable paper 13 lbs bond to 110 lbs cover (52 to 300 g/m

)

Paper capacity 5,000 sheets (2,500 × 2 21 lbs (80 g/m

))

Required power supply

AC 120V 60Hz

Dimensions

35-1/4" (W) × 30-1/32" (D) × 38-13/16" (H) (895 mm (W) × 763 mm (D) × 986 mm (H))

Weight Approx. 288 lbs (131 kg)

Name Multi Bypass Tray

Paper sizes 12" × 18" (A3W) to 5-1/2" × 8-1/2"R (A5R) ,SRA3, SRA4

Useable paper 16 lbs bond to 80 lbs cover (52 to 220 g/m

)

Paper capacity 500 sheets (21 lbs (80 g/m

))

Required power supply

Supplied from large capacity trays

Dimensions

When paper tray is closed

27-3/4" (W) × 21-57/64" (D) × 8" (H) (705 mm (W) × 556 mm (D) × 203 mm (H))

When paper tray is pulled out

34-9/16" (W) × 21-57/64" (D) × 8" (H) (878 mm (W) × 556 mm (D) × 203 mm (H))

Weight Approx. 39.7 lbs (18 kg)

MX-LC13 MX-MF11

Large Capacity Trays

SPECIFICATIONS

Name Finisher (50-sheet stapling)

Paper sizes Depends on feeder specications

Useable paper 13 lbs bond to 110 lbs cover (52 to 300 g/m

)

No. of trays 2

Tray capacity (21 lbs (80 g/m

)) *

Upper tray Non-stapled 12" × 18" (A3W) / 9" × 12" (A4W) / 11" × 17" (A3) / 8-1/2"

× 14" (B4):50 sheets

8-1/2" × 11" (A4) to 5-1/2" × 8-1/2"R (A5R): 250 sheets Lower tray Non-stapled 12" × 18" (A3W) / 9" × 12" (A4W) / 11" × 17" (A3) / 8-1/2"

× 14" (B4) / 8-1/2" × 11"R (A4R) / 5-1/2" × 8-1/2" (B5) /

7-1/4" × 10-1/2"R (B5R): 1,500 sheets

8-1/2" × 11" (A4): 3,000 sheets

5-1/2" × 8-1/2"R (A5R): 100 sheets Staple function 8-1/2" × 11" (A4): 150 units (2 to 19 sheets)

8-1/2" × 11"R (A4R) / 5-1/2" × 8-1/2" (B5): 100 units (2 to

14 sheets)

11" × 17" (A3) / 8-1/2" × 14" (B4): 100 units (2 to 14

sheets)

Max. no. of stapled sheets (21 lbs (80 g/m

))

Max. no. of 50 sheets (8-1/2" × 11" (A4) / 8-1/2" × 11"R (A4R)/ 5-1/2" × 8-1/2" (B5) / 7-1/4" × 10-1/2"R (B5R)) Max. no. of 30 sheets (11" × 17" (A3) /8-1/2" × 14" (B4))

Staple position Front: 1 position, Back: 1 position, Center: 2 positions, At slant: 1 position

Required power supply Supplied from the machine

Dimensions

When output paper tray is stored 25-55/64" (W) × 24-13/64" (D) × 38-17/32" (H) (657 mm (W) × 615 mm (D) × 979 mm (H)) When output paper tray is extended 29-13/32" (W) × 24-13/64" (D) × 40-13/16" (H) (747 mm (W) × 615 mm (D) × 1,037 mm (H))

Weight Approx. 103.6 lbs (47 kg)

* The amount of paper able to be used may vary depending on the environment the machine is operated in, the type of

paper used, and how the paper is stored.

Name Finisher (100-sheet stapling)

Paper sizes Depends on feeder specications

Useable paper 13 lbs bond to 110 lbs cover (52 to 300 g/m

)

No. of trays 3

Tray capacity (21 lbs (80 g/m

)) *

Upper tray Non-stapled 12" × 18" (A3W) / 9" × 12" (A4W) / 11" × 17" (A3) /8-1/2"

× 14" (B4) / SRA3 / SRA4: 750 sheets 8-1/2" × 11" (A4) / 8-1/2" × 11"R (A4R, B5) /7-1/4" × 101/2"R (B5R) / 5-1/2" × 8-1/2"R (A5R): 1,500 sheets

Staple function 11" × 17" (A3) / 8-1/2" × 14" (B4): 50 units or 750 sheets

8-1/2" × 11" (A4) / 8-1/2" × 11"R (A4R, B5): 100 units or

1,500 sheets Center tray Non-stapled 12" × 18" (A3W) / 9" × 12" (A4W) / 11" × 17" (A3) / 8-1/2"

× 14" (B4) / SRA3 / SRA4: 125 sheets

8-1/2" × 11" (A4) / 8-1/2" × 11"R (A4R, B5) / 7-1/4" × 10-

1/2"R (B5R) / 5-1/2" × 8-1/2"R (A5R): 250 sheets Lower tray Non-stapled 12" × 18" (A3W) / 9" × 12" (A4W) / 11" × 17" (A3) / 8-1/2"

× 14" (B4) / SRA3 / SRA4: 750 sheets

8-1/2" × 11" (A4) / 8-1/2" × 11"R (A4R, B5) / 7-1/4" × 10-

1/2"R (B5R) / 5-1/2" × 8-1/2"R (A5R): 1,500 sheets

8-1/2" x 11"/A4/B5 Non offset: 2,500 sheets Staple function 11" × 17" (A3) / 8-1/2" × 14" (B4): 50 units or 750 sheets

8-1/2" × 11" (A4) / 8-1/2" × 11"R (A4R, B5): 100 units or

1,500 sheets

• Offset output is not available for 12" × 18" (A3W) / 7-1/4" × 10-1/2"R (B5R) /

5-1/2" × 8-1/2"R (A5R).

Max. no. of stapled sheets (21 lbs (80 g/m

))

Max. no. of 100 sheets (8-1/2" × 11" (A4), B5) Max. no. of 50 sheets (11" × 17" (A3), 8-1/2" × 14" (B4), 8-1/2" × 11"R (A4R))

Staple position 1 bottom, 1 top, 2 middle

Required power supply AC 120V 60Hz

Dimensions

When output paper tray is stored 25-3/4" (W) × 30-1/8" (D) × 40-15/16" (H) (654 mm (W) × 765 mm (D) × 1040 mm (H)) When output paper tray is extended 30-51/64" (W) × 30-1/8" (D) × 40-15/16" (H) (782 mm (W) × 765 mm (D) × 1040 mm (H))

Weight Approx. 134.5 lbs (61 kg)

MX-FN24 MX-FN21

Finisher

SPECIFICATIONS

Name Saddle Stitch Finisher (50-sheet stapling)

Paper sizes Depends on feeder specications

Useable paper 13 lbs bond to 110 lbs cover (52 to 300 g/m

)

No. of trays 3

Tray capacity (21 lbs (80 g/m

)) *

Upper tray Non-stapled

12" × 18" (A3W) / 11" × 17" (A3) / 8-1/2" × 14" (B4):50 sheets

8-1/2" × 11" (A4) to 5-1/2" × 8-1/2"R (A5R): 250 sheets Lower tray Non-sort

12" × 18" (A3W) / 11" × 17" (A3) / 8-1/2" × 14" (B4) / 8-1/2" ×

11"R (A4R) / 5-1/2" × 8-1/2" (B5) / 7-1/4" × 10-1/2"R (B5R):

1,000 sheets

8-1/2" × 11" (A4): 2,000 sheets

5-1/2" × 8-1/2"R (A5R): 100 sheets Staple function 8-1/2" × 11" (A4): 150 units (2 to 12 sheets)

8-1/2" × 11"R (A4R) / 5-1/2" × 8-1/2" (B5): 100 units (2 to

9 sheets)

11" × 17" (A3) / 8-1/2" × 14" (B4): 100 units (2 to 9

sheets) Saddle stitch tray 10 units (11 to 15 sheets), 15 units (6 to 10 sheets),

30 units (2 to 5 sheets)

Max. no. of stapled sheets (21 lbs (80 g/m

))

Max. no. of 50 sheets (8-1/2" × 11" (A4) / 8-1/2" × 11"R (A4R) / 5-1/2" × 8-1/2" / 7-1/4" × 10-1/2"R (B5R)) Max. no. of 30 sheets (11" × 17" (A3) /8-1/2" × 14" (B4))

Staple position

Front: 1 position, Back: 1 position, Center: 2 positions, At slant: 1 position

Staple method (for saddle stitch) Centered fold with stapling in 2 center places

Saddle stitch fold position Centered fold

Saddle usable sizes 11" × 17" (A3) / 8-1/2 × 14" (B4) / 8-1/2" × 11"R (A4R) / 12" × 18" (A3W) / SRA3

Saddle usable paper weight

16 lbs bond (60 g/m

) to 65 lbs cover (176 g/m2)

Paper weighting 28 lbs bond (106 g/m

) to 65 lbs cover (176 g/m2). 65 lbs cover

(176 g/m

) is only able to be used in cover mode and for single sheet fold.

Max. no. of saddle-stitched sheets

Max. no. of 15 sheets (21 lbs (80 g/m2)): 14 sheets (21 lbs bond (80 g/m

)) + 1 sheet (65 lbs cover (176 g/m2))

Required power supply Supplied from the machine

Dimensions

When output paper tray is stored 25-13/32

(W) × 24-13/64" (D) × 38-17/32" (H) (657 mm (W) × 615 mm (D) × 979 mm (H)) When output paper tray is extended 29-26/64

(W) × 24-13/64" (D) × 40-13/16" (H) (747 mm (W) × 615 mm (D) × 1,037 mm (H))

Weight Approx. 136.7 lbs (62 kg)

* The amount of paper able to be used may vary depending on the environment the machine is operated in, the type of

paper used, and how the paper is stored.

Name Saddle Stitch Finisher (100-sheet stapling)

Paper sizes Depends on feeder specications

Useable paper 13 lbs bond to 110 lbs cover (52 to 300 g/m

)

No. of trays 4

Tray capacity (21 lbs (80 g/m

)) *

Upper tray Non-stapled 12" × 18" (A3W) / 9" × 12" (A4W) / 11" × 17" (A3) /8-1/2" × 14" (B4) /

SRA3 / SRA4: 750 sheets 8-1/2" × 11" (A4) / 8-1/2" × 11"R (A4R, B5) /7-1/4" × 10-1/2"R (B5R) / 5-1/2" × 8-1/2"R (A5R): 1,500 sheets

Staple function 11" × 17" (A3) / 8-1/2" × 14" (B4): 50 units or 750 sheets

8-1/2" × 11" (A4) / 8-1/2" × 11"R (A4R, B5): 100 units or 1,500 sheets Center tray Non-stapled 12" × 18" (A3W) / 9" × 12" (A4W) / 11" × 17" (A3) /8-1/2" × 14" (B4) /

SRA3 / SRA4: 125 sheets

8-1/2" × 11" (A4) / 8-1/2" × 11"R (A4R, B5) /7-1/4" × 10-1/2"R (B5R) /

5-1/2" × 8-1/2"R (A5R): 250 sheets

(Offset output is not available) Lower tray Non-stapled 12" × 18" (A3W) / 9" × 12" (A4W) / 11" × 17" (A3) /8-1/2" × 14" (B4) /

SRA3 / SRA4: 750 sheets

8-1/2" × 11"R (A4R) / 7-1/4" × 10-1/2"R (B5R) / 5-1/2" × 8-1/2"R (A5R):

1,500 sheets

8-1/2" x 11"/ (A4/B5): 2,500 sheets

(Offset output is not available) Staple function 11" × 17" (A3) / 8-1/2" × 14" (B4): 50 units or 750 sheets

8-1/2" × 11" (A4) / 8-1/2" × 11"R (A4R, B5): 100 units or 1,500 sheets Saddle stitch tray Non-stapled 16 lbs bond to 28 lbs bond (60 to 105 g/m2): 5 sheets Staple function 16 lbs bond to 21 lbs bond (60 to 81.4 g/m

): 5 units (16 to 20 sheets), 10 units (11 to 15 sheets), 15 units (6 to 10 sheets), 25 units (1 to 5 sheets) 21 lbs bond over to 28 lbs bond (81.4 g/m

over to 105 g/m2): 15 units

(6 to 10 sheets), 25 units (1 to 5 sheets)

Staple function in cover mode

16 lbs bond to 21 lbs bond (60 to 81.4 g/m2): 5 units (16 to 20

sheets), 10 units (1 to 15 sheets) 21 lbs bond over to 28 lbs bond (81.4 g/m

over to 105 g/m2): 10 units

(1 to 10 sheets)

• Offset output is not available for 12" × 18" (A3W) / 7-1/4" × 10-1/2"R (B5R) / 5-1/2" × 8-1/2"R (A5R).

Max. no. of stapled sheets (21 lbs (80 g/m

))

Max. no. of 100 sheets (8-1/2" × 11" (A4), B5) Max. no. of 50 sheets (11" × 17" (A3), 8-1/2" × 14" (B4), 8-1/2" × 11"R (A4R))

Staple position

1 bottom, 1 top, 2 middle

Staple method (for saddle stitch) Centered fold with stapling in 2 center places

Saddle stitch fold position Centered fold

Saddle usable sizes 11" × 17" (A3) / 8-1/2 × 14" (B4) / 8-1/2" × 11"R (A4R) / 12" × 18" (A3W) / SRA3

Saddle usable paper weight

16 lbs bond (60 g/m

) to 110 lbs cover (300 g/m2)

Paper weighting 28 lbs bond (106 g/m

) to 110 lbs cover (300 g/m2) is only able

to be used in cover mode and for single sheet fold.

Max. no. of saddle-stitched sheets

Max. no. of 20 sheets (21 lbs (80 g/m2)): 19 sheets (21 lbs bond (80 g/m

)) + 1 sheet (140 lbs index (256 g/m2))

Required power supply AC 120V 60Hz

Dimensions

When output paper tray is stored 30-13/64" (W) × 30-1/8" (D) × 40-15/16" (H) (767 mm (W) × 765 mm (D) × 1040 mm (H)) When output paper tray is extended 35-9/32" (W) × 30-1/8" (D) × 40-15/16" (H) (896 mm (W) × 765 mm (D) × 1040 mm (H))

Weight Approx. 238.1 lbs (108 kg)

MX-FN25 MX-FN22

Saddle stitch nisher

SPECIFICATIONS

Required power supply AC 100V-240V 50/60Hz

Dimensions

36-1/64

(W) × 29-27/32" (D) × 38-13/16" (H)

(915 mm (W) × 758 mm (D) × 986 mm (H))

Weight

High Capacity Stacker: 220 lbs (100 kg) Cart: 33 lbs (15 kg)

* Do not load sheets of different sizes.

Name High Capacity Stacker (MX-ST10)

Paper sizes 12" × 18" (A3W) to 5-1/2" × 8-1/2"R (A5R), SRA3, SRA4

Useable paper 13 lbs bond to 110 lbs cover (52 to 300 g/m

)

No. of trays 2

Tray capacity (21 lbs (80 g/m

))

Upper tray 12" × 18" (A3W) to 5-1/2" × 8-1/2"R (A5R) / SRA3 / SRA4: 250 sheets

Lower tray * 12" × 18" (A3W) / 11" × 17" (A3) / 8-1/2" × 14" (B4) / 8-1/2" × 11" (A4) / 8-1/2" × 11"R (A4R) / SRA3 / SRA4: 5,000 sheets 7-1/4" × 10-1/2" (B5) / 7-1/4" × 10-1/2"R (B5R) / 5-1/2" × 8-1/2"R (A5R): 2,500 sheets

High Capacity Stacker

Name Curl Correction Unit (MX-RB18)

Paper sizes Depends on feeder specications

Useable paper Depends on feeder specications

Dimensions

8-7/16" (W) × 29-59/64" (D) × 38-13/16" (H) (214 mm (W) × 760 mm (D) × 986 mm (H))

Weight 39.3 lbs (18.5 kg)

Curl Correction Unit

Name Relay Unit (MX-RB13)

Dimensions

8-7/16" (W) × 29-59/64" (D) × 38-13/16" (H) (214 mm (W) × 760 mm (D) × 986 mm (H))

Weight 29.5 lbs (13.4 kg)

Relay Unit

SPECIFICATIONS

Name Punch module

MX-PNX4B

Paper size for punch module 11" × 17" (A3) to 7-1/4" × 10-1/2"R (B5R)

Holes 2 holes / 3 holes (Manual select)

Required power supply Supplied from nisher/saddle stitch nisher

Dimensions

5-1/8

(W) × 20-9/32" (D) × 5-33/64" (H)

(130 mm (W) × 515 mm (D) × 140 mm (H))

Weight Approx. 3 lbs (1.4 kg)

Punch module (MX-PNX4B)

Name Punch module

MX-PN13B

Paper size for punch module 11" × 17" (A3) to 7-1/4" × 10-1/2"R (B5R)

Holes 2 holes / 3 holes (Auto select)

Required power supply Supplied from nisher/saddle stitch nisher

Dimensions

3-47/64" (W) × 28-5/32" (D) × 9-13/32" (H) (95 mm (W) × 715 mm (D) × 392 mm (H))

Weight Approx. 8.6 lbs (3.7 kg)

Punch module (MX-PN13B)

SPECIFICATIONS

Type Color scanner

Scan resolution (main × vertical)

100 × 100 dpi, 150 × 150 dpi, 200 × 200 dpi, 300 × 300 dpi, 400 × 400 dpi, 600 × 600 dpi (push scan) 50 to 9,600 dpi *

(pull scan)

Scan speed (8-1/2" × 11" (A4))

B/W: 120 sheets/minute (one-sided) Color: 120 sheets/minute (one-sided)



When in standard mode using TOSHIBA standard paper (8-1/2" × 11" (A4) size with 6% coverage) and the auto color detector is turned off. The speed varies depending on the data volume of the original.

Interface

10BASE-T/100BASE-TX/1000BASE-T, USB 2.0 (during USB memory scanning)

Compatible protocols TCP/IP (IPV4)

Compatible OS *

Pull scan (TWAIN) Windows Vista, Windows Server 2008, Windows 7,

Windows 8, Windows Server 2012

Output format

(B/W) TIFF, PDF, PDF/A, encrypted PDF, XPS *

Compression method: decompression, G3 (MH), G4 (MMR) (Gray scale/color) TIFF, JPEG, PDF, PDF/A, encrypted PDF, high compression PDF *

, XPS *

Compression method: high, mid, and low compression, Emphasis black letter *

Driver TWAIN compliant

*1: You must decrease the scan size when increasing the resolution. *2: There are cases when a connection cannot be established. Please contact your local dealer for more information. *3: A scanner function expansion kit (MX-EB11) is required.

*4: XPS (XML Paper Specication)

*5: When PDF, PDF/A, or Encrypt PDF is selected

Network Scanner Specications

Type Built-in type

Continuous print speed Same as continuous copy speed

Resolution

Data processing: 600 × 600 dpi, 1,200 × 1,200 dpi Print: 600 × 600 dpi, 1,200 × 1,200 dpi

Page description language Standard: PCL6 emulation, Adobe

PostScript®3

Compatible protocols TCP/IP (IPv4/IPv6), IPX/SPX, IPP, EtherTalk

Compatible OS *

Windows Vista, Windows Server 2008, Windows 7,Windows 8, Windows Server 2012 Macintosh (Mac OS × 10.4, 10.5, 10.6, 10.7, 10.8, 10.9 )

Internal fonts (options) 80 fonts for PCL, 139 fonts for Adobe® PostScript®3

Memory Machine system memory and hard disk

Interface 10BASE-T/100BASE-TX/1000BASE-T, USB 1.1, USB 2.0 (high speed mode)

*: There are cases when a connection cannot be established. Please contact your local dealer for more information.

Network Printer Specications

Name Inserter (MX-CF11)

Useable size for inserter

12" × 18" (A3W), 9" × 12" (A4W), 11" × 17", 8-1/2" × 14", 8-1/2" × 13-1/2", 8-1/2" × 13-2/5", 8-1/2" × 13", 8-1/2" × 11", 8-1/2" × 11"R, 7-1/4 × 10-1/2"R, 5-1/2" × 8-1/2"R, A3, B4, A4, A4R, B5, B5R, A5R, SRA3, SRA4

Useable paper 16 lbs bond to 80 lbs cover (60 g/m

to 220 g/m2))

No. of trays 2

Tray capacity (21 lbs (80 g/m2))

Upper tray: 200 sheets Lower tray: 200 sheets

Required power supply Supplied from the machine

Dimensions

21-1/4" (W) × 29-7/8" (D) × 50-1/4" (H) (540 mm (W) × 760 mm (D) × 1276 mm (H))

Weight Approx. 99.2 lbs (45 kg)

Inserter

Name Folding unit (MX-FD10)

Folding types Z-Fold, C-Fold, Accordion Fold, Double Fold, Half Fold.

Useable size for folding unit

Z-Fold: 11" × 17", 8-1/2" × 14", 8-1/2" × 11"R, A3, B4, A4R C-Fold, Accordion Fold, Double Fold, Half Fold: 8-1/2" × 11"R, A4R

Useable paper 13 lbs bond to 28 lbs bond (52 g/m

to 105 g/m2))

Tray capacity (21 lbs (80 g/m2))

C-Fold/Accordion Fold/Double Fold 2-23/64" (60 mm) (Equivalent to 40 sheets. (Equivalent to 25 sheets for Double Fold))

• Copies made in Z-Fold or Half Fold are output to the tray of the nisher (large stacker) or saddle stitch nisher (large stacker).

Required power supply Supplied from nisher/saddle stitch nisher

Dimensions

13-15/32" (W) × 30-5/16" (D) × 41-11/32" (H) (336 mm (W) × 770 mm (D) × 1050 mm (H))

Weight Approx. 145.5 lbs (66 kg)

Folding Unit

Name Trimming module (MX-TM10)

Useable size for trimming module

12" × 18" (A3W), 11" × 17", 8-1/2" × 14", 8-1/2" × 13-1/2", 8-1/2" × 13-2/5", 8-1/2" × 13", 8-1/2" × 11"R, SRA3, A3, B4, A4R

Max. no. of sheets to be trimmed

2 to 20 sheets (16 lbs bond to 21 lbs bond (60 g/m

to 81.4 g/m2))

2 to 10 sheets (21 lbs bond over to 28 lbs bond (81.4 g/m

over to 105 g/m2))

2 to 3 sheets (28 lbs bond over to 80 lbs cover (105 g/m

over to 220 g/m2))

• When plain paper trimmed. Including one front cover of 110 lbs cover (300 g/m

) or less.

Required power supply Supplied from saddle stitch nisher

Dimensions

9-7/8" (W) × 24-15/32" (D) × 15-7/8" (H) (251 mm (W) × 625 mm (D) × 403 mm (H))

Weight Approx. 70.6 lbs (32 kg)

Trimming Module

SPECIFICATIONS

SUPPLIES

Standard supplies for this product that can be replaced by the user include paper,

toner cartridges, and staple cartridges for the nisher. Be sure to use only TOSHIBA-specied products for the toner cartridges, nisher staple cartridge, and transparency lm.

Supply of spare parts and consumables

The supply of spare parts for repair of the machine is guaranteed for at least 7 years following the termination of production. Spare parts are those parts of the machine which may break down within the scope of the ordinary use of the product, whereas those parts which normally exceed the life of the product are not to be considered as spare parts. Consumables too, are available for 7 years following the termination of production.

Proper storage

1. Store the supplies in a location that is:

• clean and dry,

• at a stable temperature,

• not exposed to direct sunlight.

2. Store paper in the wrapper and lying at.

3. Paper stored in packages standing up or out of the wrapper may curl or become damp, resulting in paper misfeeds.

GENUINE SUPPLIES

For best copying results, be sure to use only TOSHIBA Genuine Supplies which are designed, engineered, and tested to maximize the life and performance of TOSHIBA products. Look for the Genuine Supplies label on the toner package.

Storing toner cartridges

Store a new toner cartridge box horizontally with the top side up. Do not store a toner cartridge standing on end. If stored standing on end, the toner may not distribute well even after shaking the cartridge vigorously, and will remain inside the cartridge

without owing out.

Staple cartridge

The nisher and saddle nisher require the following staple cartridge: MX-SCX3 (for saddle stitch of saddle stitch nisher)

Approx. 2000 per cartridge 4 cartridges

MX-SCX2 (for nisher (large stacker) and saddle stitch nisher (large stacker))

Approx. 5000 per cartridge 3 cartridges

MX-SCX1 (for saddle stitch of saddle stitch nisher (large stacker))

Approx. 5000 per cartridge x 3 cartridges

AR-SC2 (for nisher and saddle stitch nisher)

Approx. 5000 per cartridge x 3 cartridges

Storage of supplies

OPTIONS

Optional Units

When optional units are installed, nishing operations such as stapling, punching or folding, can be performed.

1 Finisher/Saddle Stitch Finisher 6 This Unit

2 Folding Unit 7 Multi Bypass Tray

3 High Capacity Stacker 8 Large Capacity Trays

4 Inserter 9 Status Indicator

5 Curl Correction Unit

1 2 3 4 5 6

High Capacity Stacker

Stacks a large number of sheets in the stacker tray of the paper cart, enabling you to move the stacker tray on the stacker cart. This stacker provides an LED that

noties users of the status. You can connect up to two large capacity stackers.

High Capacity Stacker MX-ST10

PAPER CART MX-CA10

Inserter

Inserts a sheet of paper into a specic page as an insertion sheet.

Inserter MX-CF11

• 200 sheets x 2

Folding Unit

Each set of copies can be folded.

Folding Unit MX-FD10

• Half Fold

• Z-Fold

• C-Fold

• Accordion Fold

• Double Fold

Finisher/Saddle Stitch Finisher

Each set of copies can be stapled, or the sheets can be folded and stapled. Installing a punch module automatically enables hole punching that is convenient

for ling.

Finisher MX-FN24

Finisher MX-FN21

• e-STUDIO907 only

• 50 sheets

• 100 sheets

Saddle Stitch Finisher MX-FN25

Saddle Stitch Finisher MX-FN22

• e-STUDIO907 only

• 50 sheets

• 15 sheet (saddle stitch nisher)

• 100 sheets

• 20 sheets (saddle stitch nisher)

• For saddle folding, it trims a

side drop, offering a goodlooking output image (In use of trimming module).

OPTIONS

Curl Correction Unit

Perform the curl correction of the output.

Curl Correction Unit MX-RB18

Large Capacity Trays

You can drastically reduce the time to load the large number of paper.

Large Capacity Tray MX-LC12

Large Capacity Tray MX-LCX3 N

• 8-1/2" x 11", A4 or B5 paper can be loaded.

• e-STUDIO907 only

• 12" x 18" (A3W) to 8-1/2" x 11"

(B5) paper can be loaded.

Large Capacity Trays MX-LC13

• Up to two large capacity trays can be connected.

• 2 trays

OPTIONS

Status Indicator

These indicators show the status of the machine.

Status Indicator MX-SL10 N

This function is used to forward all data sent and received by the machine to a specied destination (Scan to E-mail address, Scan to FTP destination or Scan to Network Folder destination). This function can be used by the administrator of the machine to archive all sent and re-

ceived data. To congure the document administration settings, click [Application Settings] and

then [Document Administration Function] in "Settings mode". (Administrator rights are required.)

The forwarding data, exposure, and resolution settings of sent and received data remain in effect.

ADMINISTRATOR

Account Password

User users users

Administrator admin admin

System administrator sysadmin sysadmin

Do not forget the new administrator password.

An administrator password is required to congure the machine settings using administrator

rights.

The settings can be congured from either the operation panel or by using a computer web

browser. After setting up the machine, refer to "Settings mode" in the User’s Manual to set a new password.

The same administrator password is used for the operation panel and the Web page. If the administrator changes a password on the operation panel, the password will be valid when logging in to the Web page.

Password for logging in from a computer

As factory default, "Administrator" is the only account allowed to log in from a Web browser. By setting user authentication, "System Administrator" will also be allowed to log in from the Web browser. You can also specify a device account as a login user.

The factory default passwords for respective accounts are shown in the following. Logging in as an "Administrator" or "System Administrator" allows you to manage all the settings available via Web browser.

Forwarding all sent or received data to the administrator (document administration function)

Setting mode password

OTHERS (NOISE EMISSION)

Noise emission values

The following shows noise emission values as measured according to ISO7779.

Sound power level L

WAd

e-STUDIO907 e-STUDIO1057 e-STUDIO1207

Operating 7.9 B 8.0 B 8.1 B

Standby - - -

Noise emission

Security Precautions

Sound pressure level LpAm

e-STUDIO907 e-STUDIO1057 e-STUDIO1207

Operating 61 dB 62 dB 62 dB

Standby - - -

• Operating: With options MX-FN21, MX-RB18, and MX-MFX1.

• Standby: “ -” = less than background noise.

To Administrators

• To avoid physical security problems, such as hardware removal or inappropriate disassembly at the installation site, take all necessary measures, such as checking who enters and leaves the site.

• When connecting this product with an outer network such as the Internet, only operate it in a network environment protected by a rewall, etc. to prevent

information from being leaked due to incorrect settings or avoid illegal access by unauthorized users.

• To prevent the conguration settings from being altered improperly or similar, before

you use this product, change the administrator and user registration passwords set by factory default. Also, be sure periodically to change each password set for this product.

• In order to make proper use of the network and user management functions, be sure to read the User's Manual rst.

• Be sure to understand the security policy and its procedure in your organization, and

manage and operate this equipment and external devices according to the policy after

rst reading the operator's manual. Then explain the security instructions to general

users who are authorized to use this equipment to let them conform to the security rule.

In order to make correct use of this product’s security function, rst read the following precautions

carefully. Be sure to assign administrators who have enough capability to sustain responsible man-

agement since signicant privileges for managing and handling this equipment will be given them.

• Provide general users with the appropriate privilege of using this equipment and

keep supervising its correct operation.

• Always check if the network function and user management function are enabled in order to maintain security. Should you happen to come across any abnormality, contact your service technician immediately. See the User's Manual for the checking method.

• If any failure or unauthorized access occurs in this equipment, check the logs in Job Logs to nd the cause. For details of checking logs, refer to the User's Manual.

• Check your log regularly to guard against unauthorized access by identity theft.

To general users

• After you have nished operating the equipment, be careful not to forget to remove

any originals, printed paper or USB storage devices.

• Change the password regularly. Make sure not to use any predictable number such as your birthday or employee ID number, and keep it secret.

• Do not leave the equipment during the performance of the job since your originals

may be seen or the output paper could be taken by someone.

PRINTED IN CHINA

2014L YT1

TINSE5315FCZZ

DP-9077/1057/1207

OME14009800

R140820P1700-TTEC

Ver00 F 2014-09

DIGITAL MULTIFUNCTIONAL SYSTEM Quick Start Guide

1-11-1, OSAKI, SHINAGAWA-KU, TOKYO, 141-8562, JAPAN

Toshiba e-Studio 907, e-Studio 1057, e-Studio 1207 Quick Start Manual

Specifications and Main Features

Frequently Asked Questions

User Manual