Page 1
PRINTED IN JAPAN
TOSHIBA Thermal Printer
B-SX6T/SX8T SERIES
Document No. EO15-33002
Original Mar., 2006
(Revised )
Option Installation Manual
Page 2
EO15-33002
TABLE OF CONTENTS
Page
1. Cutter Module: B-SX208-QM-R-------------------------------------------------------------------------------1- 1
2. Strip Module: B-SX908-H-QM-R -----------------------------------------------------------------------------2- 1
3. Ribbon Saving Module: B-SX908-R-QM-R ---------------------------------------------------------------3- 1
4. Wireless LAN Module: B-SA704-WLAN-QM-------------------------------------------------------------4- 1
5. Serial Interface Board: B-SA704-RS-QM-R --------------------------------------------------------------5- 1
6. Real Time Clock: B-SA704-RTC-QM-R --------------------------------------------------------------------6- 1
7. Expansion I/O Board: B-SA704-IO-QM-R-----------------------------------------------------------------7- 1
CAUTION!
1. This manual may not be copied in whole or in
p
art without prior written permission of TOSHIBA
TEC.
2. The contents of this manual may be changed without notification.
3. Please refer to your local Authorised Service representative with regard to any queries you
may have in this manual.
Copyright © 2006
by TOSHIBA TEC CORPORATION
A
ll Rights Reserved
570 Ohito, Izunokuni-shi, Shizuoka-ken, JAPAN
Page 3
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO15-33002
1. Cutter Module: B-SX208-QM-R
1- 1
INSTALLATION PROCEDURE FOR OPTIONAL
EQUIPMENT
1. Cutter Module: B-SX208-QM-R
B-SX208-QM-R is an optional cutter module for the B-SX6T/SX8T Series.
• Packing List
The following parts are supplied with the kit. Make sure you have all items shown below.
Cutter Unit (1 pc.)
Cutter Module Cover
(1 pcs.)
Cutter Harness (1 pc.)
Cutter Support Plate
(1 pc.)
Print Head Cleaner
(1 pc.)
Cutter Attaching
Screw (2 pcs.)
FL-4x6 Screw (2 pcs.)
SM4x6 Screw (1 pc.)
Installation Manual
(1 copy)
Note: for how to use the print head cleaner, please refer to the Owner’s Manual.
• Installation Procedure
1. Turn the power off.
2. Open the right side cover and top covers.
WARNING!
1. Turn the printer power off and disconnect the power cord before installing an optional
equipment.
2. Be careful not to pinch your fingers or hands with the covers.
3. Be careful not to injure your fingers when installing the cutter module.
Top Cover
Right Side Cover
Page 4
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO15-33002
1. Cutter Module: B-SX208-QM-R
1- 2
3. Remove the six screws (B-4x6, FL-4x6 and B-3x8) to detach the left side cover.
4. Remove the four FL-4x6 screws to detach the front cover.
5. Remove the SM-4x8 screw and operation panel harness to detach the operation panel.
FL-4x6 Screw
B-3x8 Screw
B-4x6 Scre
w
FL-4x6 Screw
FL-4x6 Scre
w
FL-4x6 Scre
w
SM-4x8 Screw
Operation Panel Harness
Operation Panel
B-4x6 Scre
w
Left Side Cove
r
Page 5
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO15-33002
1. Cutter Module: B-SX208-QM-R
1- 3
6. Attach the cutter support plate to the main frame with the two screws (FL-4x6).
7. Connect the cutter harness to CN3 on the cutter interface PC board through the opening of the cutter
unit.
8. Install the cutter unit with the supplied four screws (cuter attaching screws, SM-4x6 and FL-4x6). When
installing the cutter unit, make sure that the cutter guide does not contact with the platen. If so, a print
failure or noise may occur.
FL-4x6 Screw
FL-4x6 Scre
w
Cutter Support Plate
Main Frame
Cutter Interface PC Board
CN3
Cutter Unit
Cutter Harness
Cutter Unit
FL-4x6 Screw
SM-4x6 Screw
Cutter Attaching Scre
w
Opening
Page 6
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO15-33002
1. Cutter Module: B-SX208-QM-R
1- 4
9. Connect the cutter harness to the connector on the printer through the opening of the main frame.
10. Mount the cutter cover with the two screws.
Fit the cutter cover into the cutter attaching screws and secure the cutter cover with the two screws.
11. Attach the operation panel and the left side cover on the printer.
12. Close the top cover and right side cover.
13. After the reassembly is completed, perform a test print to confirm that the cutter works properly.
If the print start position becomes misaligned when media is fed in the reverse direction, fine adjust
the back feed value using the Back Feed Fine Adjustment procedure in system mode.
Cutter Harness
Connecto
r
Main Flame
Screw
Cutter Attaching
Screw
Opening
Cutter Cove
r
Screw
Page 7
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO15-33002
1. Cutter Module: B-SX208-QM-R
1- 5
• Adjusting the Cutter Guide Plates
After attaching the cutter unit the following adjustment procedure should be employed to prevent paper
jams.
1. Attach the cutter guide plate A with the two SM-4x6C screws so that the fixed cutter is positioned
0.1 mm to 0.4 mm above the bottom of the cutter guide plate A.
2. Attach the cutter guide plate B with the two FL-4x8 screws so that there is a clearance of 0.5 mm
between the cutter guide plate A and cutter guide plate B using a clearance gauge.
• Media loading procedure------------- Owner’s Manual, Section 2.4
• Operation check------------------------Owner’s Manual, Section 2.10
• System mode setting------------------System Mode Manual
• Cleaning --------------------------------- Owner’s Manual, Section 4.1.5
Cutter Guide Plate B
Cutter Guide Plate A
Screw
(FL-4x8)
Fixed Cutte
r
Screw
(SM-4x6C)
0.1 to 0.4 mm
0.5 mm
Page 8
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO15-33002
2. Strip Module: B-SX908-H-QM-R
2- 1
2. Strip Module: B-SX908-H-QM-R
B-SX908-H-QM-R is an optional strip module for the B-SX6T/SX8T Series.
• Packing List
The following parts are supplied with the kit. Make sure you have all items shown below.
Strip Unit (1 pc.)
Strip Harness (1 pc.)
Installation Manual (1 copy)
• Installation Procedure
1. Turn the power off.
2. Open the right side cover and top cover.
3. Remove the six screws (B-4x6, FL-4x6 and B-3x8) to detach the left side cover.
Top Cover
Right Side Cover
FL-4x6 Screw
B-3x8 Screw
B-4x6 Scre
w
B-4x6 Scre
w
Page 9
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO15-33002
2. Strip Module: B-SX908-H-QM-R
2- 2
4. Remove the four FL-4x6 screws to detach the front cover.
5. Remove the SM-4x8 screw and operation panel harness to detach the operation panel.
6. Connect the strip harness to CN5 on the PWM PC Board through the opening of the strip base.
FL-4x6 Screw
FL-4x6 Scre
w
FL-4x6 Scre
w
SM-4x8 Screw
Operation Panel Harness
Operation Panel
Strip Unit
Strip Harness
Strip Base
PWM PC Board
Opening
CN5
Page 10
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO15-33002
2. Strip Module: B-SX908-H-QM-R
2- 3
7. Install the strip unit into the printer with the four FL-4x6 screws which were removed in step 4.
8. Connect the strip harness to the connector on the printer through the opening of the main frame.
9. Attach the operation panel and the left side cover on the printer.
10. Close the top cover and right side cover. After that, perform an operation check for a proper strip issue.
• Media loading procedure------------- Owner’s Manual, Section 2.4
• Operation check------------------------Owner’s Manual, Section 2.10
• System mode setting------------------System Mode Manual
• Cleaning --------------------------------- Owner’s Manual, Section 4.1.6
FL-4x6 Screw
FL-4x6 Screw
FL-4x6 Scre
w
Strip Unit
Connecto
r
Opening
Main Frame
Strip Harness
Page 11
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO15-33002
3. Ribbon Saving Module: B-SX908-R-QM-R
3- 1
3. Ribbon Saving Module: B-SX908-R-QM-R
B-SX908-R-QM-R is an optional strip module for the B-SX6T Series.
• Packing List
The following parts are supplied with the kit. Make sure you have all items shown below.
Solenoid (R) (1 pc.)
(Connector: White)
Solenoid (L) (1 pc.)
(Connector: Yellow)
RSV PC Board (1 pc.)
Locking Support (3 pcs.)
SM-3x5 Screw (4 pcs.)
Installation Manual (1 copy)
• Installation Procedure
1. Turn the power off.
2. Open the right side cover and top cover.
Top Cover
Right Side Cover
Page 12
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO15-33002
3. Ribbon Saving Module: B-SX908-R-QM-R
3- 2
3. Remove the two B-4x6 screws to detach the print head front plate.
4. Remove the four SM-4x8 screws to detach the blind plate (R) and blind plate (L).
5. Attach the blind plate (L) to the solenoid (L) with the two SM-3x5 screws.
6. Reverse the blind plate (L) and attach the three locking supports.
B-4x6 Screw
B-4x6 Scre
w
SM-4x8 Scre
w
SM-4x8 Screw
Print Head Front Plate
Blind Plate (R)
Blind Plate (L)
SM-3x5 Screw
Blind Plate (L)
Solenoid (L)
Locking Support
Page 13
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO15-33002
3. Ribbon Saving Module: B-SX908-R-QM-R
3- 3
7. Fit the locking supports into the RSV PC board, then connect the solenoid (L) harness to CN1 on the
RSV PC board.
8. Attach the blind plate (R) to the solenoid (R) with the two SM-3x5 screws.
9. Draw the two harnesses (2 pins, 3 pins) from the head block, then connect the harness (2 pins) and the
harness (3 pins) into CN2 and CN3 on the RSV PC board.
RSV PC Board
CN1
Harness
Solenoid (L)
SM-3x5 Scre
w
Solenoid (R)
Blind Plate (R)
Harness (3 pins)
Harness (2 pins)
CN3
CN2
RSV PC Board
Page 14
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO15-33002
3. Ribbon Saving Module: B-SX908-R-QM-R
3- 4
10. Connect the solenoid (R) harness to the head block harness.
11. While inserting the head up link into the spring pin of the solenoid, attach the solenoids (L) and (R) to
the head block.
Note: It is easier to attach the solenoid in the following procedure. First remove the plunger from the
solenoid. Next, insert the head up link into the plunger then the plunger into the solenoid.
Solenoid (R)
Harness
Spring Pin
Head Up Lin
k
Solenoid (L)
Head Up
Lin
k
Plunger
Plunge
r
Solenoid
Page 15
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO15-33002
3. Ribbon Saving Module: B-SX908-R-QM-R
3- 5
12. Insert piled 12 pieces of tag paper (0.16-mm thick, I-BEST-S is recommended.) between the print hea d
and the platen. Then turn the head lever to the LOCK position.
13. Fully push the head up link to the direction indicated by the arrow 1. Push the solenoid toward the
head up link as indicated by the arrow 2, then secure the solenoid with the two SM-4x8 screws.
Solenoid (L) Solenoid (R)
Head Lever
Tag Paper
LOCK Position
Head Up Link
Head Up
Link
1
2
SM-4x8 Scre
w
1
2
SM-4x8 Screw
Solenoid (L)
Solenoid (R)
Page 16
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO15-33002
3. Ribbon Saving Module: B-SX908-R-QM-R
3- 6
14. After installing the solenoids (L) and (R), reassemble the print head front plate so that this part fits into
the slot of the shaft.
15. Perform a label issue to check the ribbon saving operation.
Print Head Front Plate
Shaft Slot
Page 17
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO15-33002
4. Wireless LAN Module: B-SA704-WLAN-QM-R
4- 1
4. Wireless LAN Module: B-SA704-WLAN-QM-R
B-SA704-WLAN-QM-R is an optional wireless LAN module for the B-SX6T/SX8T Series, B-SA4TM/SA4TP
Series and B-852-QQ/QP-R Series .
• Packing List
The following parts are supplied with the kit. Make sure you have all items shown below.
Wireless LAN Board (1 pc.)
Antenna Cover (1 pc.)
SMW-3x6 Screw (4 pcs.)
Installation Manual (1 copy)
Shield Sheet (1.pc)
FCC/IC Sticker (1 pc.)
NOTES:
1. DO NOT CHANGE the DIP Switch settings on the Wireless LAN Board. Doing so may cause a malfunction.
2. MAC address of the Wireless LAN module will be necessary when setting the MAC address filtering function
of an access point. As it is printed on the top of the wired LAN connector on the Wireless LAN Board, write
down it on Installation Manual before mounting the covers so that an end user can know the MAC address.
3. Be careful not to hit or damage the antenna when installing this kit. A damaged antenna may affect the
performance.
4. The shield sheet is used only when this option is installed in the B-SA4TP model.
DIP Switch
MAC Address
12-digit code printed on the right
side of “W” is MAC address.
Wireless LAN Board
Antenna
Page 18
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO15-33002
4. Wireless LAN Module: B-SA704-WLAN-QM-R
4- 2
• Installation Procedure
1. Turn the power off.
2. Open the right side cover and top cover.
3. Remove the six screws (B-4x6, FL-4x6 and B-3x8) to detach the left side cover.
4. Remove the two SMW-3x6 screws to detach the blind plate.
Top Cover
Right Side Cover
FL-4x6 Screw
B-3x8 Screw
B-4x6 Scre
w
B-4x6 Scre
w
Left Side Cove
r
SMW-3x6
Blind Plate
Page 19
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO15-33002
4. Wireless LAN Module: B-SA704-WLAN-QM-R
4- 3
5. Put the antenna of the wireless LAN board out of the opening of the back of the printer.
Care must be taken not to hit the antenna against the printer frame, as damaged antenna may affect the
performance.
6. As the following picture shows, secure the wireless LAN board to the back of the printer with the two out
of the supplied SMW-3x6 screws.
Opening
Wireless LAN Board
A
ntenna
SMW-3x6 scre
w
Page 20
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO15-33002
4. Wireless LAN Module: B-SA704-WLAN-QM-R
4- 4
7. Secure the wireless LAN board onto the MAIN PC board with the SMW-3x6 screw.
8. Connect the wireless LAN power cable to CN12 on the MAIN PC board.
9. Connect the LAN cable as shown below.
SMW-3x6 Screw
Wireless LAN Board
CN12
MAIN PC Board
MAIN PC Board
LAN Cable
CN17
Page 21
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO15-33002
4. Wireless LAN Module: B-SA704-WLAN-QM-R
4- 5
10. Fit the antenna cover to the back of the printer. Secure it with the SMW-3x6 screw.
11. Reassemble the side panel into the printer.
A
ntenna Cover
Pass the LAN cable through the
cut of the antenna cover.
LAN Cable
SMW-3x6 Screw
Page 22
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO15-33002
4. Wireless LAN Module: B-SA704-WLAN-QM-R
4- 6
• Country Code
As available frequency bands are different from country to country, be sure to set a country code before
installing a wireless LAN module in a user’s printer. Also, ask an end user to confirm a country code. Use
of a wireless LAN module with a wrong country code could violate each country’s Laws and Regulations for
Radio Equipment, and violators could be subject to penalties.
The country code cannot be changed through the Web browser, but TELNET.
<How to set a country code using TELNET>
(1) Disconnect the LAN cable connected to the printer, then connect the printer to a host PC with a
straight LAN cable via a relay connector.
When using a hub in place of a relay connector, use a cross cable or use the straight LAN cable
with the hub’s inverting input function.
(2) Open the MS-DOS prompt, then type in “telnet 192.168.10.21” (default IP address).
(3) Enter a password to log in. (Password: tecbcp)
(4) From the top menu, change a country code using the following command.
=>ctry XX (XX=new country code. See Country Code Table.)
(5) The new country code will become effective by turning the printer off and on again.
(6) A country code can be checked by typing “=>ctry” on the telnet console.
<Country Code Table>
Country
code
Country name
Country
code
Country name
Country
code
Country name
US U.S.A./Canada GR Greece IE Ireland
FR France SE Sweden GB U.K.
PT Portugal HU Hungary AU Australia
NO Norway BE Belgium FI Finland
DE Germany IT Italy LU Luxembourg
ES Spain NL Netherlands CH Switzerland
IS Iceland LI Liechtenstein NZ New Zealand
AT Austria DK Denmark
Regarding various settings or operation check for the wireless LAN, refer to the System Mode Manual.
CAUTION! The following information must not be disclosed to users. (Internal use only)
Page 23
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO15-33002
5. Serial Interface Board: B-SA704-RS-QM-R
5- 1
5. Serial Interface Board: B-SA704-RS-QM-R
B-SA704-RS-QM-R is an optional expansion I/O board for the B-SX6T/SX8T Series, B-SA4TM/SA4TP and
B-852-QQ/QP-R Series.
• Packing List
The following parts are supplied with the kit. Make sure you have all items shown below.
SIO PC Board (1 pc.)
Serial Interface Cable
Locking Support (1 pc.)
PCB Support Plate (1 pc.)
SMW-3x6 Screw (3 pcs.)
Installation Manual (1 copy)
NOTE: Make sure that the serial interface cable is connected to CN4 on the SIO PC board.
• Installation Procedure
1. Turn the power off.
2. Open the right side cover and top cover.
Top Cover
Right Side Cover
Page 24
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO15-33002
5. Serial Interface Board: B-SA704-RS-QM-R
5- 2
3. Remove the six screws (B-4x6, FL-4x6 and B-3x8) to detach the left side cover.
4. Remove the two SMW-3x6 screws to detach the blind plate.
5. Attach the supplied PCB support plate to the back of the printer with one of the supplied SMW-3x6
screws.
FL-4x6 Screw
B-3x8 Screw
B-4x6 Scre
w
B-4x6 Scre
w
Left Side Cove
r
SMW-3x6
Blind Plate
SMW-3ｘ6 Scre
w
PCB Support Plate
Page 25
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO15-33002
5. Serial Interface Board: B-SA704-RS-QM-R
5- 3
6. Connect the serial interface cable of the SIO PC board to CN12 on the MAIN PC board.
7. Fit the locking support into the MAIN PC board.
8. Secure the SIO PC board to the back of the printer with the two SMW-3x6 screws. Fit the locking
support into the SIO PC board.
9. Reassemble the left side cover.
SIO PC Board
Serial Interface Cable
CN12
MAIN PC Board
Locking Support
MAIN PC Board
SMW-3x6
Scre
w
Locking Support
SIO PC Board
Page 26
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO15-33002
6. Real Time Clock: B-SA704-RTC-QM-R
6- 1
6. Real Time Clock: B-SA704-RTC-QM-R
B-SA704-RTC-QM-R is an optional real time clock for the B-SX6T/SX8T series, B-SA4TM/SA4TP series
and B-852-QQ/QP-R series.
NOTE: When the B-SA704-IO-QM-R Expansion I/O board or B-SA704-RS-QM-R serial interface board has
already been installed in the printer, the interface cable of the real time clock cannot be connected to the
MAIN PC board. Please remove this optional PC board temporarily, prior to installing the real time clock.
• Packing List
The following parts are supplied with the kit. Make sure you have all items shown below.
Real Time Clock (1 pc.) See NOTE.
SMW-4x8 Screw (1 pc.)
Lithium Battery CR2032 (1 pc.)
Installation Manual (1 copy)
Battery Sticker (1 pc.)
NOTE:
Make sure that the interface cable
is connected to CN1 on the real
time clock.
• Installation Procedure
1. Turn the power off.
2. Open the right side cover and top cover.
Interface
Cable
Top Cover
Right Side Cover
Page 27
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO15-33002
6. Real Time Clock: B-SA704-RTC-QM-R
6- 2
3. Remove the six screws (B-4x6, FL-4x6 and B-3x8) to detach the left side cover.
4. Place the lithium battery into the battery socket in the direction of the arrow.
NOTES: 1. Place the battery with the “+” mark facing up.
2. A new battery is supposed to last about 2 years or more, but it varies depending on the operating
conditions. When a new battery is loaded, write down the battery replacement date on a supplied
battery sticker, and attach it to the reverse side of the left side cover as a reminder.
Battery Socket
Lithium Batter
y
+
Reverse side of Left Side Cover
Battery Sticker
FL-4x6 Screw
B-3x8 Screw
B-4x6 Scre
w
B-4x6 Scre
w
Left Side Cove
r
Page 28
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO15-33002
6. Real Time Clock: B-SA704-RTC-QM-R
6- 3
5. Attach the real time clock to the printer with the SMW-4x8 screw.
6. Connect the interface cable to CN501 on the MAIN PC board.
7. Attach the left side cover which was removed in Step 3 to the back of the printer. Care must be taken
not to catch the interface cable by the left side cover.
NOTE: When the B-SA704-IO-QM-R expansion I/O board or B-SA704-RS-QM-R serial interface board was
removed beforehand, re-install it.
Real Time Clock
SMW-4x8 Scre
w
Interface Cable
CN501
MAIN PC Board
Page 29
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO15-33002
7. Expansion I/O Board: B-SA704-IO-QM-R
7- 1
7. Expansion I/O Board: B-SA704-IO-QM-R
B-SA704-IO-QM-R is an optional expansion I/O board for the B-SX6T/SX8T Series, B-SA4TM/SA4TP
Series and B-852-QQ/QP-R Series.
• Packing List
The following parts are supplied with the kit. Make sure you have all items shown below.
Expansion I/O Board (1 pc.)
See NOTE.
Blind Plate (1 pc.)
SMW-3x6 Screw (3 pcs.)
Installation Manual (1 copy)
NOTE: Make sure that the interface cable is connected to CN1 on the
expansion I/O board.
• Installation Procedure
1. Turn the power off.
2. Open the right side cover and top cover.
Interface Cable
Top Cover
Right Side Cover
Page 30
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO15-33002
7. Expansion I/O Board: B-SA704-IO-QM-R
7- 2
3. Remove the six screws (B-4x6, FL-4x6 and B-3x8) to detach the left side cover.
4. Remove the two SMW-3x6 screws to detach the blind plate.
NOTE: Keep the blind plate for future use.
5. Attach the expansion I/O board to the back of the printer with one of the supplied SMW-3x6 screws.
FL-4x6 Screw
B-3x8 Screw
B-4x6 Scre
w
B-4x6 Scre
w
Left Side Cove
r
SMW-3x6
Blind Plate
SMW-3ｘ6 Scre
w
Expansion I/O Board
Page 31
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO15-33002
7. Expansion I/O Board: B-SA704-IO-QM-R
7- 3
6. Connect the interface cable to CN4 on the MAIN PC board.
7. Attach the supplied blind plate to the back of the printer with the supplied two SMW-3x6 screws.
NOTE: The blind plate is not required to be attached when the optional serial interface board is also installed.
8. Attach the left side cover which was removed in Step 3 to the back of the printer.
CN4
MAIN PC Board
Interface Cable
Expansion I/O Board
SMW-3ｘ6 Scre
w
Blind Plate
Serial Interface Board
Loading...