Toshiba B-FP3D SERIES, B-FP3D-GH30-QM-R, B-FP3D-GS30-QM-R, B-FP3D-GS40-QM-R, B-FP803-BT-R Owner's Manual

Portable Printer

B-FP3D SERIES

Owner's Manual

! 00TSCC0317701!

V

g

g

A

(

CE Compliance (for EU only)

This product complies with the requirements of EMC and R&TTE Directives including their amendments.
CE marking is the responsibility of TOSHIBA TEC GERMANY IMAGING SYSTEMS GmbH, Carl-Schurz-Str. 7,
41460 Neuss, Germany.
For a copy of the related CE Declaration of Conformity, please contact your dealer or TOSHIBA TEC.

FCC Notice

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Changes or modification not expressly approved by manufacturer for compliance could void the user’s authority
to operate the equipment.

“This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations. ”
“Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur lematériel brouilleur
du Canada.”

ORSICHT:

Maschinenlärminformations-Verordnung 3. GPSGV, der höchste Schalldruckpegel beträgt 70 dB(A) oder

er gemäß EN ISO 7779.

weni

Some types of this product are equipped with a wireless communication device, such as, BT800 and
GS2100MIP. Please be sure to read the enclosed Precautions for Handling of Wireless Communication
Devices before usin

Note:

When you purchase interface cables on the market, shielded cables must be chosen and used.

this product.

for CANADA only)

This product is designed for commercial usage and is not consumer product.

The following information is for EU-member states only:
Disposal of batteries and/or accumulators
(based on EU-Directive 2006/66/EC,
Directive on batteries and accumulators and waste batteries and accumulators)

The use of the symbol indicates that batteries and/or accumulators may not be disposed as
unsorted municipal waste and has to be collected separately.
By ensuring that batteries and/or accumulators are disposed of correctly, you will help prevent
potential negative consequences for the environmental and human health, which could
otherwise be caused by inappropriate waste handling of this product.
For more detailed information about the take-back and recycling of batteries and/or
accumulators, please contact your supplier where you purchased this product.

California Proposition 65 Warning: USA-California only
This Product contains chemicals known to the State of California to cause cancer, birth defects, or other
reproductive harm.

© 2016 TOSHIBA TEC CORPORATIONAll Rights Reserved
1-11-1, Osaki, Shinagawa-ku, Tokyo 141-8562, JAPAN

PRINTED IN INDONESI

E

SPTM-0273

1

ForTaiwan

NCC 警語

低功率電波輻射性電機管理辦法第十二條經型式認證合格之低功率射頻電機，非經許可，公司、商號或使
用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。第十四條低功率射頻電機之使用不得影
響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項
合法通信，指依電信規定作業之無線電信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻
射性電機設備之干擾.



For Mexico

Bluetooth Module WiFi Module
IFT: XX-XXXX IFT: YY-YYYY
BT800 GS2100MIP
Laird Gainspan

- La operación de este equipo está sujeta a las siguientes dos condiciones:
(1) es posible que este equipo o dispositivo no cause interferencia perjudicial y
(2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su
operación no deseada



ForKorea


인명안전과관련된서비스는할수없음
이 기기는 가정용(B 급) 전자파적합기기로서 주로 가정에서 사용하는 것을 목적으로 하며, 모든
지역에서 사용할 수 있습니다



2

<English>

p

p

p

CAUTION!

1. Only use TOSHIBA TEC battery packs designed and manufactured for use with the specific printer model. There is a
risk of explosion if the battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.

2. When an external power source such as an AC adapter is connected to the printer, DO NOT use any device other than
an exclusive one.

AC adapter: B-EP800-AC-QM-R (Model: FSP065-REBN2)
Cigarette lighter adapter: B-EP802-DC12-QM-R
DC ada

<Franaçis>

PRÉCAUTIONS!

1. N’utilisez que les packs batteries Toshiba Tec conçus et fabriqués pour être utilisés avec ce modèle spécifique. Il y a un
risque d’explosion si la batterie est remplacée par un modèle non adapté. Veuillez vous débarrasser des batteries
usagées en respectant la réglementation.

2. Lorsque vous connectez l’imprimante sur un adaptateur secteur externe, N’UTILISEZ PAS d’adaptateur différent de
celui préconisé

Adaptateur secteur: B-EP800-AC-QM-R (Model: FSP065-REBN2)
Adaptateur allume cigare: B-EP802-DC12-QM-R
Convertisseur continu: B-EP800-DC48-QM-R

<Deutsch>

Achtung!

1. Benutzen Sie nur den für Ihr Druckmodell bestimmten Akku. Bei Verwendung eines falschen Akkus besteht die Gefahr
einer Explosion. Entsorgen Sie den alten Akku gemäß den Vorschriften!

2. Sofern der Drucker den Strom durch eine externe Quelle bezieht, z.B. mit Hilfe eines AC Adapters, benutzen Sie nur
den vorgegebenen Adapter.

AC Adapter: B-EP800-AC-QM-R (Model: FSP065-REBN2)
Batterie-Ladekabel für Zigarettenanzünder: B-EP802-DC12-QM-R
DC Ada

<Español>

ATENCIÓN!

1. Utilice baterías diseñadas y fabricadas por Toshiba Tec específicamente para este modelo. Existe riesgo de explosión si
se usa un tipo de batería incorrecto. Deshágase de las baterías usadas según las instrucciones.

2. Cuando conecte un alimentador externo a la impresora, como por ejemplo un adaptador AC, NO USE ningún
dispositivo diferente al modelo exclusivo de cada impresora.

Adaptador AC: B-EP800-AC-QM-R (Model: FSP065-REBN2)
Adaptador para mechero: B-EP802-DC12-QM-R
Ada

<Nederlands>

WAARSCHUWING!

1. Gebruik enkel de batterijeenheid die overeenstemt met de desbetreffende printer. Vervanging door een verkeerd type
batterij kan een ontploffing veroorzaken. Dank uw batterijen af zoals voorgeschreven.

2. Gebruik uitsluitend onderstaande wisselstroomadapter om de printer aan te sluiten met een externe voeding:

AC adapter: B-EP800-AC-QM-R (Model: FSP065-REBN2)
Sigarettenaansteker adapter: B-EP802-DC12-QM-R
DC adapter: B-EP800-DC48-QM-R

B-FP3D-GH30-QM-R
B-FP3D-GH40-QM-R
B-FP3D-GS30-QM-R
B-FP3D-GS40-QM-R

ter: B-EP800-DC48-QM-R

B-FP3D-GH30-QM-R
B-FP3D-GH40-QM-R
B-FP3D-GS30-QM-R
B-FP3D-GS40-QM-R

B-FP3D-GH30-QM-R
B-FP3D-GH40-QM-R
B-FP3D-GS30-QM-R
B-FP3D-GS40-QM-R

ter: B-EP800-DC48-QM-R

B-FP3D-GH30-QM-R
B-FP3D-GH40-QM-R
B-FP3D-GS30-QM-R
B-FP3D-GS40-QM-R

tador DC: B-EP800-DC48-QM-R

B-FP3D-GH30-QM-R
B-FP3D-GH40-QM-R
B-FP3D-GS30-QM-R
B-FP3D-GS40-QM-R

B-FP803-BT-R

B-FP803-BT-R

B-FP803-BT-R

B-FP803-BT-R

B-FP803-BT-R

3

<Italiano>

어댑터

p

ATTENZIONE!

1. Utilizzare il pacco batterie corretto per ogni modello di stampante. Esiste il rischio di esplosine se utilizzate le batterie
sbagliate. Smaltite le batterie secondo le istruzioni.

2. Qualora la stampante sia collegata ad una alimentazione esterna, esempio la presa in corrente alternata, utilizzate

Adattatore AC: B-EP800-AC-QM-R (Model: FSP065-REBN2)
Adattatore per accendisigaro per automezzi: B-EP802-DC12-QM-R
Adattatore DC: B-EP800-DC48-QM-R

< Português >

ATENÇÃO!

1. Utilize as baterias desenhadas e fabricadas pela Toshiba Tec especificamente para este modelo. Existe risco de

2. Ao conectar uma impressora à alimentação externa, como por exemplo a um adaptador AC, NÃO UTILIZE nenhum

Adaptador AC: B-EP800-AC-QM-R (Model: FSP065-REBN2)
Adaptador para isqueiro: B-EP802-DC12-QM-R
Ada

<Polski>

UWAGA!

1. Należy używać wyłącznie zastawów baterii zaprojektowanych i wyprodukowanych dla konkretnego modelu drukarki.

2. W przypadku używania zewnętrznego źródła zasilania drukarki np. zasilacza AC, NIE NALEŻY używać innego

Zasilacz AC: B-EP800-AC-QM-R (Model: FSP065-REBN2)
Zasilacz samochodowy: B-EP802-DC12-QM-R
Zasilacz DC: B-EP800-DC48-QM-R

<한국어>

주의!

1. 배터리 팩은 본기기의 전용품을 사용 해 주십시오. 다른 배터리를 사용하면 폭발의 위험이 있습니다. 사용이 끝난

2. 본기기에 AC 어댑터 등의 외부 전원을 접속하는 경우, 반드시 본기기 전용품을 사용 해 주십시오. 본기기 전용품

AC 어댑터: B-EP800-AC-QM-R (Model: FSP065-REBN2)
시가 라이터 어댑터: B-EP802-DC12-QM-R
DC

<中文（繁體字）>

注意!

1. 套装充電池只適用与本機専用品。更換不適當形式的電池時，持有爆發的危険性。使用過後的電池，請按照説明書處理。

2. 聯接本機的AC電源供應器等外部電源時，只適用与本機的専用品。請勿聯接本機専用品之外任何産品。

AC 電源供應器: B-EP800-AC-QM-R (Model: FSP065-REBN2)
點烟機電源供應器: B-EP802-DC12-QM-R
DC 電源供應器: B-EP800-DC48-QM-R

B-FP3D-GH30-QM-R
B-FP3D-GH40-QM-R
B-FP3D-GS30-QM-R
B-FP3D-GS40-QM-R

esclusivamente l’adattatore corretto:.

explosão se for utilizado um tipo de bateria incorrecta. Desfaça-se das baterias usadas de acordo com as instruções.

B-FP3D-GH30-QM-R
B-FP3D-GH40-QM-R
B-FP3D-GS30-QM-R
B-FP3D-GS40-QM-R

dispositivo diferente do modelo exclusivo para cada impressora.

tador DC: B-EP800-DC48-QM-R

Wymiana baterii na baterię innego typu grozi wybuchem. Należy utylizować baterie zgodnie z podanymi instrukcjami.

B-FP3D-GH30-QM-R
B-FP3D-GH40-QM-R
B-FP3D-GS30-QM-R
B-FP3D-GS40-QM-R

urządzenia poza wyspecyfikowanym.

배터리는 설명서에 따라 처리해 주십시오.

B-FP3D-GH30-QM-R
B-FP3D-GH40-QM-R
B-FP3D-GS30-QM-R
B-FP3D-GS40-QM-R

이외는 접속 하지 말아 주십시오

: B-EP800-DC48-QM-R

B-FP3D-GH30-QM-R
B-FP3D-GH40-QM-R
B-FP3D-GS30-QM-R
B-FP3D-GS40-QM-R

B-FP803-BT-R

B-FP803-BT-R

B-FP803-BT-R

B-FP803-BT-R

B-FP803-BT-R

4

English

y

–

p

quip

)

p

The following information is for EU-member states only:
Disposal of products
(based on EU-Directive 2002/96/EC,
Directive on Waste electrical and electronic equipment – WEEE)

The use of the symbol indicates that this product may not be disposed as unsorted municipal waste and
has to be collected separately. Integrated batteries and accumulators can be disposed of with the
product. They will be separated at the recycling centers.
The black bar indicates that the product was placed on the market after August 13, 2005.
By ensuring this product is disposed of correctly, you will help prevent potential negative consequences
for the environmental and human health, which could otherwise be caused by inappropriate waste
handling of this product.
For more detailed information about the take-back and rec

cling of this product, please contact your

Franaçis

Deutsch

Español

Les informations suivantes ne concernent que les utilisateurs des pays membres de l’union Européenne :
Recyclage des produits
(Basé sur la directive Européenne 2002/96/EC,
Directive sur le recyclage des équipements électriques et électroniques

L’utilisation de ce symbole indique que ce produit ne doit pas être jeté sans tri préalable, comme un
déchet classique, mais doit être collecté séparément. Les batteries et accumulateurs intégrés peuvent
être laissés en place, ils seront récupérés par le centre de recyclage.
La barre noire indique que ce produit a été mis sur le marché après le 13 Août 2005.
En vous assurant que ce produit est correctement mis au rebut, vous participerez à prévenir les
éventuelles conséquences néfastes sur l’environnement et la santé publique qui pourraient autrement
être causés par une gestion inappropriée des déchets contenus dans ce produit.
Pour obtenir des informations complémentaires sur la récupération et le recyclage de ce produit, veuillez
contacter le fournisseur au

Wiederververtungsinformationen für Verbraucher:
(gemäß EU-Directive 2002/96/EC,
Gesetz über das Inverkehrbringen, die Rücknahme und die umweltverträgliche Entsorgung von Elektro- und
Elektronikgeräten [ElektroG]" – WEEE).

Die folgenden Informationen gelten nur für EU-Mitgliedsstaaten.
Das durchgestrichene Mülltonnensymbol weist darauf hin, dass dieses Produkt nicht wie allgemeiner
Hausmüll behandelt werden darf. Verbaute Batterien oder Akkus müssen vorher entnommen und separat
entsorgt werden.
Der schwarze Balken unter dem Symbol besagt, das das Produkt nach dem 13. August 2005 in Verkehr
gebracht wurde.
Indem Sie aktiv mit helfen, dieses Produkt ordnungsgemäß zu entsorgen, helfen Sie mit mögliche
negativen Auswirkungen auf die Umwelt sowie die menschliche Gesundheit zu vermeiden.
Für nähere Informationen zur Rücknahme und Wiederverwertung dieses Produktes wenden Sie sich bitte
an Ihren Lieferanten.

rès duquel vous en avez fait l’acquisition.

REEE –WEEE)

La siguiente información solo concierne a los Estados Miembros de la UE:
Desechado de los productos
(basado en la Directiva Europea 2002/96/EC,
Directiva sobre Residuos de e

Argentina

El uso de este símbolo indica que el producto no puede ser desechado como basura común doméstica
por lo que debe ser recogido de forma separada. Sus baterías y acumuladores integrados pueden
eliminarse junto con el aparato. Estos elementos serán separados en los centros de reciclado.
La barra negra indica que el producto fue puesto en el Mercado después del 13 de Agosto de 2005.
Asegurando que nos deshacemos del producto de forma correcta, ayudaremos a evitar potenciales
consecuencias negativas tanto para el medio ambiente como para la salud pública, que podrían
producirse debido a un tratamiento inapropiado.
Para obtener información más detallada sobre la recogida y reciclaje de su producto, por favor, póngase
en contacto con el

os eléctricos y electrónicos –REEE –WEEE

roveedor que se lo suministró.

La siguiente información es solo para A rgentina:

El uso de este símbolo indica que este producto no puede ser tratado como residuos domésticos.
Asegúrese que este producto se deseche correctamente, Usted ayudara a evitar posibles consecuencias
negativas para el medio ambiente y la salud humana, que podrían derivarse de la incorrecta
manipulación de este producto.

Para mas información sobre el reciclaje de este producto, consulte con nuestro su distribuidor donde

adquirió el producto.

5

Nederlands

j

)

Onderstaande informatie geldt enkel in EU lidstaten:
Het afdanken van producten (volgens EU-richtlijn 2002/96/EC,
Richtli

Italiano

Português

Polski

n betreffende afgedankte elektrische en elektronische apparatuur –WEEE

Dit symbool geeft aan dat dit product niet mag afgedankt worden als algemeen huishoudelijk afval. Het
dient afzonderlijk gecollecteerd te worden. Geïntegreerde batterijen of laders kunnen samen met dit
product afgedankt worden. Zij worden in het recyclagecentrum gescheiden. De zwarte balk geeft aan dat
dit product na 13 augustus 2005 verhandeld werd.
Door een aangepaste afdanking van dit product beschermt u het milieu en de volksgezondheid tegen
mogelijke schadelijke gevolgen, die anders zouden kunnen voortvloeien uit het onjuist verwerken van de
resten van dit product. Vraag inlichtingen over de terugname en recyclage van dit product aan uw
leverancier.

Le seguenti informazioni sono solo gli stati membri della UE:
Smaltimento del prodotto
(basato sulla direttiva EU-Directive 2002/96/EC,
Direttiva sullo smaltimento per il Riciclaggio delle Apparecchiature Elettriche od Elettroniche – RAEE – WEEE)

Questo simbolo indica che i prodotti non possono essere smaltiti come rifiuti urbani non differenziati ma
devono essere raccolti separatamente. Eventuali batterie o accumulatori possono essere smaltiti con il
prodotto. Verranno separati dai centri di riciclaggio
La barra near indica che il prodotto è stato inserito nel mercato dopo il 13 Agosto 2005
Assicuratevi che questo prodotto sia smaltito correttamente, contribuirete a prevenire potenziali
conseguenze negative per l'ambiente e la salute umana, che potrebbero essere altrimenti causate da uno
smaltimento improprio di questo prodotto.
Per maggiori dettagli sul riciclo, o su come rendere il prodotto, contattate il vostro fornitore.

A informação que se segue é apenas dirigida a países membros da UE:
Reciclagem de produtos (baseado na directive-UE 2002/96/EC,
Directiva sobre a reciclagem de resíduos de equipamentos eléctricos e electrónicos – REEE – WEEE)

O uso deste símbolo indica que este produto não pode ser colocado nos pontos de recolha de lixo
comum e deve ser recolhido separadamente. As baterias integradas e acumuladores podem ser
entregues juntamente com o produto. Serão depois separados nos centros de reciclagem.
A barra negra indica que o equipamento foi colocado no mercado após 13 de Agosto de 2005.
Ao assegurar-se que este produto é tratado correctamente está a ajudar a prevenir potenciais
consequências negativas para o ambiente e para a saúde humana, que poderiam ser causadas pelo
inapropriado tratamento deste produto.
Para mais informação sobre a reciclagem e tratamento deste produto, contacte o seu fornecedor.

Informacje dla Państw członkowskich Unii Europejskiej:
Utylizacja urządzeń
(na podstawie dyrektywy Unii Europejskiej 2002/96/EC,
Dyrektywa dotycząca odpadów elektrycznych i elektronicznych – WEEE)

Użycie symbolu oznacza, że urządzenie nie może być traktowane jako niesegregowane odpady i musi
być zebrane oddzielnie. Zintegrowane baterie i akumulatory mogą być utylizowane razem z urządzeniem.
Zostaną one posegregowane w centrach utylizacji.
Czarny prostokąt oznacza, że urządzenie zostało wprowadzone na rynek po 13 sierpnia 2005.
Poprzez zastosowanie się do prawidłowych procedur utylizacji tego urządzenia, pomożecie Państwo
ograniczyć potencjalne negatywne skutki dla środowiska i zdrowia ludzkiego, które mogłyby zaistnieć na
skutek niewłaściwej utylizacji tego urządzenia.
W celu uzyskania dodatkowych informacji odnośnie zwrotu i utylizacji tego urządzenia prosimy o kontakt
z punktem zakupu tego urządzenia.

Following information is only for India:

The use of the symbol indicates that this product may not be treated as household waste. By ensuring this product is
disposed of correctly, you will help prevent potential negative consequences for the environment and human health,
which could otherwise be caused by inappropriate waste handling of this product.
For more detailed information about the take-back and recycling of this product, please contact your supplier where
you purchased the product.
This product complies with the “India E-waste Rule 2011” and prohibits use of lead, mercury, hexavalent chromium,

polybrominated biphenyls or polybrominated diphenyl ethers in concentrations exceeding 0.1％ by weight and 0.01%
by weight for cadmium, except for the exemption set in Schedule II of the Rule.

6

Precautions for Handling of Wireless Communication Devices
Bluetooth® Module: BT800 (GH30/GS30 model)
Wireless LAN Module: GS2100MIP (GH40/GS40 model)
Trade Mark

Bluetooth is a registered trademark owned by Bluetooth SIG, Inc. and used byTOSHIBA TEC CORPORATION under
license.

Cautions

General
For all countries and areas
This product is a wireless communication device, and the use of this product is restricted to the following countries or
areas. If the product is used in the countries or areas other than the following, you may be punished according to the
laws of those countries or areas.
USA, Canada, Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany,
Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, United Kingdom, Switzerland, Norway, Iceland, Liechtenstein, Australia, New
Zealand

For Europe

For Bluetooth and Wirelss LAN

Hereby, TOSHIBA TEC CORPORATION, declares that the BT800 and Gainspan are in compliance with the
essential requirements and other relevant provisions of Directive 1999/5/EC. This equipment uses a radio frequency
band that has not been harmonized throughout all EU and EFTA countries, and can be used EU and EFTA
countries.

For USA

This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, includinginterference that may cause undesired operation.

Changes or modification not expressly approved by manufacturer forcompliance could void the user’s authority to
operate the equipment.

For Canada

Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.

To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from
windows to provide maximum shielding. Equipment that is installed outdoors is subject to licensing.

For Taiwan
Caution

根據低功率電波輻射性電機管理辦法

Without permission, any company, firm or user shall not alter the frequency, increase the power, or change the
characteristics and functions of the original design of the certified lower power frequency electric machinery.
The application of low power frequency electric machineries shall not affect the navigation safety nor interfere a legal
communication, if an interference is found, the service will be suspended until improvement is made and the
interference no longer exists.

For safety

Do not use this product in locations where use may be forbidden, for example,in an aeroplane or a hospital. If you do
not know the forbidden areas, please referto and follow the airline company or medical institution guidelines.
Flight instruments or medical equipment may be affected, causing a serious accident.

Since this product uses extremely low power compared with mobile phones, itcannot possibly interfere the
pacemakers and defibrillators. However, if the useof this product should be likely to have affected the pacemaker or
defibrillator,immediately stop using the product and contact your TOSHIBA TEC sales agent.

Do not disassemble, modify, or repair the product. Doing so may cause injury. Also, modification is against the Laws
and Regulations for Radio Equipment. Please ask your TOSHIBA TEC sales agent for repair.

Precaution in use

This product communicates with other devices by radio. Depending on the installation location, orientation,
environment, etc., its communication performance may deteriorate or devices installed near by may be affected.

7

Keep away from microwave devices.
Communication performance may deteriorate or a communication error may occur due to radio interfearence emitted from
the microwave device.
Since the Bluetooth and wireless LAN use the same radio frequency band, each radio wave may interfere with each other
when they are used at the same time, causing a deterioration of communication performance or a disconnection of network.
If there is any problem with connection, please stop using either Bluetooth or wireless LAN.

Do not use the product on a metal table or near a metal object.
Communication performance may be deteriorated.

BT800 Specification

Bluetooth version V4.0 Dual Mode
Frequency 2.402 to 2.480 GHz
Maximum Transmit Class 1
Power +8 dBm from antenna "
Receive Sensitivity -89 dBm
Data Rates Up to 3 Mbps (over the air)
Communication distance 3m/360deg (For FP3D specification)

Certification (Module)

Antenna specification

US/FCC: SQGBT800, CANADA/IC:
3147A-BT800

(Put on "Contains FCC ID: SQG­BT800" in certifcation label)
Europe: RTTE 1995/5/EC Annex IV

PN: AT3216-B2R7HAA, Mfg.: ACX,
Type Ceramic, Gain: 0.5(dBi)

GS2100MIP Specification

Standard IEEE802.11 b / g / n
Frequency
Spacing 5 MHz

Channel: USA:1 to 11 ch ; EUROPE:1 to 13 ch
Antenna PCB Trace antenna (built-in module) @2.0dBi

Communication speed/
Modulation

Receive Sensitivity 802.11b -93dBm ; 802.11g -74dBm ; 802.11n -71dBm
Transmission output 802.11b Typ. 17 dBm (50.12mW)

CAUTION!

1.To avoid injury, be careful not to catch or jam your fingers while opening or closing the cover.

2.Do not touch moving parts. To reduce the risk that fingers, jewelry, clothing, etc., be drawn into the moving parts, turn off
the power switch to stop movement.

Safety Summary

Personal safety in handling or maintaining the equipment is extremely important. Warnings and Cautions necessary for
safe handling are included in this manual. All warnings and cautions contained in this manual and written inside or outside
of the printer should be read and understood before handling or maintaining the equipment.
Do not attempt to effect repairs to this equipment. If a fault occurs that cannot be rectified using the procedures described
in this manual, turn off the power, then contact your authorised TOSHIBA TEC representative for assistance.

Safety Precautions

This Owner's Manual and the products (machines) which you have purchased contain indications which should be
observed in order to use the machines safely and prevent harm to yourself and others and damage to property. The
meanings of these indications and symbols are given below.
Read these indications and become familiar with their contents before reading this Owner's Manual.

Precautions

The following precautions will help to ensure that this machine will continue to function correctly.
(1) Try to avoid locations that have the following adverse conditions:

*Temperatures out of the specification
*High Humidity
*Direct sunlight
*Excessive vibration

(2) The cover should be cleaned by wiping with a dry cloth or a cloth slightly dampened with a mild detergent solution.

NEVER USE THINNER OR ANY OTHER VOLATILE SOLVENT on the plastic covers.
(3) USE ONLY TOSHIBA TEC SPECIFIED media.
(4) DO NOT STORE the media where it might be exposed to direct sunlight, high temperatures, high humidity, dust, or gas.
(5) Any data stored in the memory of the printer could be lost during a printer fault.
(6) DO NOT open the top cover and battery cover during operation. Doing so will stop printer operation.
(7) DO NOT scratch the surface of printed labels or receipt with a sharp object.
(8) Be sure to use a shielded interface cable.

CAUTION!

1.This manual may not be copied in whole or in part without the prior written permission of TOSHIBA TEC.

2.The contents of this manual ma y be change d wit hout not ifi ca ti o n.

3.Please refer to your local Authorised Service representative with regard to any queries you may have in this manual.

USA: 2,412 to 2,462 MHz ; EUROPE:2,412 to 2,472
MHz

IEEE802.11b : CCK modulation rates of 5.5 and 11

Mbps; DSSS modulation for data rate of 1 and 2 Mbps

IEEE802.11g : OFDM modulation rates of 6, 9, 12, 18,
24, 36, 48 and 54 Mb/s

IEEE802.11n : 1x1 single stream, 20MHz channels
(1x1 HT20), 400/800ns GI, MCS0-7
Data rates of 7.2, 14.4, 21.7, 28.9, 43.3, 57.8, 65.0, 72.2
Mbps

802.11g Typ. 14 dBm (25.12mW)

802.11n Typ. 12 dBm (15.85mW)

8

If water or any other liquid enters the machine, turn off the power. Continuous use of the machine under such

•

conditions may cause fire or electric shock.

• If the enclosure is damaged when dropped or subject to shock, turn off the power. Continuous use of the

machine under such conditions may cause fire or electric shock.

• Avoid continuous exposure to direct sunlight or high temperature as this may cause fire.

• Do not remove covers or modify the machine by yourself. Doing so may cause fire or electric shock.

• Avoid water, operation with wet hands or cleaning with a moistened cloth. Failure to do this may cause fire or

electric shock.

• Do not wipe the machine with a cloth moistened with thinner or other volatile solvent as this may cause fire or

electric shock.

• DO NOT USE a spray cleaner containing flammable gas for cleaning this product, as this may cause a fire.

Use the specified battery only. Failure to do this may cause fire or electric shock.

•

• Danger of explosion if the battery is incorrectly replaced. Replace the battery only with a TOSHIBA TEC

Corporation, Battery Pack Model B-FP803-BT-R 7.4V 2500mAh Li-ion. Discard used batteries according to
the manufacturer's instruction.

• Do not disassemble and modify the battery because it has a protection unit in it. Doing so may break the

protection unit, causing the battery to heat up, burst or burn.

• If the battery gets wet, dry it completely. Using a wet battery may cause fire or electric shock.

Be aware of the following precautions when using batteries. Otherwise they could heat up, burst or burn.

•

 Do not throw the battery into fire or heat it with a microwave or oven, etc.
 Do not load the battery with the electrodes reversed.
 Do not connect the electrodes with metal objects like wire. Do not carry or store the battery along with

 Do not stick a needle into, hammer, step on, or drop the battery.
 Do not solder the battery.
 Do not leave the battery where the temperature is more than 50°centigrade, such as inside a car or in

• Keep away from flame or other sources of heat. Failure to do this may cause fire or machine failure.

• Do not drop or shock the machine as this may cause machine failure.

• During lightning, turn off and keep away from the machine because of danger of electric shock and machine

failure.

• Avoid locations subject to rapid change in temperature as this causes condensation, causing electric shock

or machine failure.

• Do not damage the print head, platen or strip roller with a sharp object. Doing so may cause machine failure.

• Do not touch or contact the print head element with a hard object. Doing so may cause machine failure.

• Use the specified media only. Failure to do this may cause machine failure.

• Be sure to turn off the machine before replacing the battery, or machine failure may occur.

• Do not charge the battery near flame or under direct sunlight. High temperature may activate or damage the

protection unit of the battery, disabling the electric charge or causing it to overheat, burst, or burn.

• Unload the battery when the machine will not be used for a longtime. Failure to do this may cause machine

failure.

• Keep the battery away from flame, a heat source or other locations subject to high temperature.

Failure to do this may cause it to over heat or burn.

• Do not force the battery into the machine or battery charger. Doing so may cause the battery to overheat,

burst or burn. Check for the correct electrode.

• Do not connect the battery to a power outlet or a car cigarette lighter jack as this may cause the battery to

overheat, burst or burn.

• Because the B-FP803-BT-R Series battery is exclusively for the B-FP3D Series printer, do not use the

battery in other machines. Doing so may damage the battery or affect the performance and life of the
battery.

WARNING
This indicates that there is the risk of death or serious injury if the machines are handled
improperly or contrary to this indication.

metal objects such as necklaces, hairpins, etc.

direct sunlight.

CAUTION
This indicates that there is the risk of personal injury or damage to objects if the machines are
improperly handled contrary to this indication.

9

Précaution pour la manipulation du module de communication

sans fil Bluetooth®: BT800 (modèle GH30/ GS30)
Module Wireless LAN: GS2100MIP (modèle

GH40/GS40)

Trade Mark

Bluetooth est une marque propriété de Bluetooth SIG, inc. et utilisée par TOSHIBA TEC CORPORATION sous
licence.

Précautions
Général

Pour tous pays et toutes zones géographiques

Ce produit intègre un module de communication sans fil, et l’utilisation de ce produit est restreinte aux pays ou zones
ci-dessous. L’utilisation de ce produit dans des pays ou des zones ne figurant pas dans la liste ci-dessous
vous expose aux sanctions légales prévues dans les pays ou les zones géographiques concernées.

Japon, Etats-Unis, Canada, Autriche, Belgique, Bulgarie, Cyprus, Chypre, République Tchèque, Danemark, Estonie,

Finlande, France, Hongrie, Allemagne, Grèce, Irlande, Italie, Lettonie, Lituanie, Luxembourg, Malte, Pays-bas,
Pologne, Portugal, Slovaquie, Slovénie, Espagne, Suède, Royaume Uni, Norvège, Lichtenstein, Islande, Suisse,

Australie, Nouvelle Zélande , Mexique, Chine, République de Corée, Taïwan

Pour L’Europe

Pour Bluetooth et pour le wireless LAN

TOSHIBA TEC CORPORATION déclare par la présente que le BT800 et le GS2100MIP sont en conformité avec les
principales exigences et les dispositions pertinentes de la Directive 1999/5/EC. Cet équipement utilise une bande
radiofréquence qui n’a pas été harmonisée dans tous les pays membres de L’UE et de l’EFTA, et peut être utilisé
uniquement dans ces pays.

Pour les Etats-Unis
Ce produit est conforme au chapitre 15 des règlements FCC. L’usage de ce produit est sujet aux deux conditions
suivantes:
(1) Ce dispositif ne doit pas causer d’interférences, et
(2) Ce dispositif doit supporter toutes les interférences reçues, y compris les interférences qui pourraient entraîner un
fonctionnement anormal.

Tout changement ou modification qui ne serait pas expressément approuvée par le fabricant au niveau de la
conformité peut entraîner l’interdiction d’utiliser cet équipement.

Pour le Canada
L’usage de ce produit est sujet aux deux conditions suivantes: (1) Ce dispositif ne doit pas causer d’interférences, et
(2) Ce dispositif doit supporter toutes les interférences reçues, y compris les interférences qui pourraient entraîner
un fonctionnement anormal.

Pour prévenir les interférences en utilisation normale, ce dispositif est prévu pour une utilisation en intérieur et
éloigné des fenêtres afin de fournir une protection maximale. Les équipements installés en extérieur doivent faire
l’objet d’un enregistrement.

Sécurité
N’utilisez pas ce produit dans des endroits où l’usage en est interdit, en particulier dans les hôpitaux.
Si vous n’avez pas connaissance des zones d’interdiction, reportez-vous aux instructions du corps médical. Faute
de prendre ces précautions, les équipements médicaux peuvent être affectés, avec des conséquences sérieuses.
Ce produit peut affecter le fonctionnement de certains stimulateurs cardiaques implantés, et d’autres dispositifs
implantés médicalement. Les personnes portant un stimulateur cardiaque doivent être informées que l’utilisation de
ce
produit à proximité immédiate d’un stimulateur cardiaque peut causer un dysfonctionnement de ce dernier.

10

Si vous avez le moindre soupçon que des interférences se produisent, éteignez immédiatement ce produit et
prenez contact avec votre agent commercial TOSHIBA TEC.
Ne démontez pas ce produit, ne le modifiez pas et ne le réparez pas vous-même.
Une telle conduite peut entraîner des blessures. De plus, toute

modification va à l’encontre des lois et

règlements sur

les équipements radio.

Pour toutes réparations, veuillez vous adresser à votre agent commercial TOSHIBA TEC..

Précaution d’utilisation
Ce produit communique en radio avec d’autres systèmes. En fonction de l’endroit où il est installé, de son

orientation, de son environnement etc., ses performances de communication pourraient se détériorer, ou bien
des dispositifs installés à proximité pourraient être perturbés.

Maintenir à l’écart des fours micro-ondes
La qualité de communication peut être détériorée ou une erreur peut se produire en raison des perturbations
radios générées par un four à microondes.

Dans la mesure où le Bluetooth et le wireless LAN partagent la même plage de fréquences radio, les deux
modules peuvent interférer l’un avec l’autre s’ils sont utilisés en même temps, entraînant une détérioration de
la communication ou une déconnexion du réseau. Si un problème de connexion se produit, veuilles arrêter
d’utiliser soit le Bluetooth soit le wireless LAN.

N’utilisez pas ce produit sur une surface métallique ou près d’un objet métallique. La qualité de communication

peut en être affectée.

BT800 Specification

Bluetooth version V4.0 Dual Mode
Fréquence de 2,402 à 2,480 GHz

" Transmit Maximum Classe 1

Puissance 8 dBm de l'antenne "
Sensibilité de réception -89 dBm

Taux de données jusqu'à 3 Mbps (sur l'air )
Distance de communication 3m / 360deg ( Pour les spécifications

Certification ( Module ) US / FCC : SQGBT800 , CANADA / IC :

RQS- BT800 " dans l'étiquette de

Europe: RTTE 1995/5 / CE Annexe IV

Spécification de l'antenne AT3216 - B2R7HAA , Mfg .: ACX , type

FP3D )

3147A - BT800 ( Mettez "Contient FCC ID
:

certifcation )

céramique , Gain: 0,5 ( dBi )

Spécifications GS2100MIP

Standard IEEE802.11 b / g / n
La fréquence USA: 2,412 to 2,462 MHz

Espacement 5 MHz
Canal USA:1 to 11 ch EUROPE:1 to 13 ch
Antenne Trace antenne PCB (module intégré) @ 2.0dBi

Vitesse de communication /
Modulation

Sensibilité de réception 802.11b -93dBm ; 802.11g -74dBm ; 802.11n

Sortie de la transmission 802.11b Typ. 17 dBm (50.12mW)

EUROPE:2,412 to 2,472 MHz

IEEE802.11b - taux CCK de modulation de 5,5
et 11 Mbps ; DSSS modulation pour le taux de
1 et 2 Mbps data rate of 1 and 2 Mbps

IEEE802.11g -Rapidités de modulation OFDM
de 6, 9 , 12 , 18, 24 , 36, 48 et 54 Mb / s

IEEE802.11n - 1x1 flux unique , les canaux de
20MHz ( 1x1 HT20 ) , 400 / 800ns GI , MCS0-7
Data rates of 7.2, 14.4, 21.7, 28.9, 43.3, 57.8,

65.0, 72.2 Mbps

-71dBm

802.11g Typ. 14 dBm (25.12mW)

802.11n Typ. 12 dBm (15.85mW)

11