Toshiba B-EX4 T1 Series, B-EX4 T2 Series Product Description
PRINTED IN JAPAN
TOSHIBA Thermal Printer
B-EX4 T1/T2 SERIES
Document No. SPTM-0152
Original Feb, 2012
(Revised )
Product Description
TABLE OF CONTENTS
Page
1. OUTLINE -------------------------------------------------------------------------------------------------1- 1
1.1 PRINTER SPECIFICATIONS --------------------------------------------------------------------------- 1- 1
1.2 DESCRIPTION OF MODEL NUMBER --------------------------------------------------------------- 1- 1
1.3 APPEARANCE AND DIMENTIONS (APPROXIMATE) -----------------------------------------1- 2
1.4 BASIC SPECIFICATIONS ------------------------------------------------------------------------------- 1- 4
1.5 ELECTRONICS SPECIFICATIONS------------------------------------------------------------------- 1- 9
2. SUPPLY SPECIFICATIONS-------------------------------------------------------------------------2- 1
2.1 MEDIA (Paper)---------------------------------------------------------------------------------------------- 2- 1
2.2 RIBBON ---------------------------------------------------------------------------------------------------- 2- 11
2.3 CARE AND HANDLING OF THE MEDIA AND RIBBON -------------------------------------- 2- 15
2.4 PRINT CONDITIONS ----------------------------------------------------------------------------------- 2- 16
2.5 SPECIFICATION OF RFID TAG (for B-EX700-RFID-H1-QM-R) --------------------------- 2- 18
2.6 SPECIFICATION OF RFID TAG (for B-EX700-RFID-U2-EU-R) ---------------------------- 2- 21
2.7 SPECIFICATION OF RFID TAG (for B-EX700-RFID-U2-US-R) ---------------------------- 2- 25
2.8 SPECIFICATION OF RFID TAG (for B-EX700-RFID-U2-CN-R)---------------------------- 2- 29
3. OPTIONAL KIT -----------------------------------------------------------------------------------------3- 1
3.1 CUTTER MODULE: B-EX204-QM-R (Disk Cutter), -----------------------------------------------3- 2
3.2 PEEL MODULE: B-EX904-H-QM-R ------------------------------------------------------------------ 3- 3
3.3 EXPASION I/O CARD: B-EX700-IO-QM-R----------------------------------------------------------3- 5
3.4 RTC/USB host INTERFACE BOARD: B-EX700-RTC-QM-R ----------------------------------- 3- 5
3.5 RFID MODULE: B-EX700-RFID-H1-QM-R---------------------------------------------------------- 3- 5
3.6 RFID MODULE: B-EX700-RFID-U2-EU/US/CN-R ------------------------------------------------3- 6
3.7 WIRELESS LAN BOARD: B-EX700-WLAN-QM-R------------------------------------------------ 3- 8
CAUTION!
1. This manual may not be copied in whole or in part without prior written permission of TOSHIBA
TEC.
2. The contents of this manual may be changed without notification.
3. Please refer to your local Authorised Service representative with regard to any queries you
may have in this manual.
Copyright © 2011-2012
by TOSHIBA TEC CORPORATION
A
ll Rights Reserved
570 Ohito, Izunokuni-shi, Shizuoka-ken, JAPAN
1. OUTLINE SPTM-0152
1.1 PRINTER SPECIFICATIONS
1-1
1. OUTLINE
1.1 PRINTER SPECIFICATIONS
1) Various bar codes, characters and graphic data can be printed using both thermal transfer and
thermal direct methods. This printer can also print writable characters and logos at designated
coordinates by using a graphic command.
2) The USB and LAN interface are available as standard interfaces between the printer and a PC. In
addition, optional interfaces such as RS-232C interface, Centronics interface, expansion I/O
interface, RTC & USB Host interface and Wireless LAN interface are available.
3) A 32-bit CPU and ASIC equipped with several peripheral LSIs realizes high system performance.
4) With the element positioned at the edge of the print head, print quality is improved because the
media passes straight through.
5) The B-EX4 series accommodates a max. printing speed of 14”/sec.
6) High throughput can be obtained with “on-the-fly” formatting.
7) Installation space is minimized because the media is loaded internally.
8) The metal cover and damper provide a heavy-duty enclosure.
9) Various optional devices, including the Strip module including the rewinder, the ribbon saving
module which economizes ribbon usage, rotary cutter module, disk cutter module, RFID module,
RS-232C interface, Centronics interface, expansion I/O interface, RTC & USB Host interface and
Wireless LAN interface are available.
NOTE: Every size is written in millimeter (mm) in this manual. To obtain the size in inch, divide by 25.4.
1.2 DESCRIPTION OF MODEL NUMBER
B - E X 4 T 2 - G S 1 2 - QM - R
Compliance with ROHS
R: RoHS compliant model
Destination Code
QM: Global
CN: China
None: Japan
Machine Type
2: Oversea Standard Model
5: Japan Model
6: WLAN with CN Model
8: RFID with CN model
Machine Version
1: Version 1
Issue mode
S: Standard type
H: Peel-off type
C: Cutter type
Resolution
G: 203dpi
T: 305dpi or 300dpi
H: 600dpi
Print head type / Sensor Position
1: Near Edge head / Center
2: Flat head / left side
Printing method
D: Thermal direct
T: Thermal transfer and thermal direct
Printing width
4: 4 inches width
6: 6 inches width
1. OUTLINE SPTM-0152
1.3 APPEARANCE AND DIMENSIONS (APPROXIMATE)
1-2
1.3 APPEARANCE AND DIMENSIONS (APPROXIMATE)
1.3.1 Appearance
Front drawing
Side drawing
1.3.2 Operation Panel
Key Function
(1) Feeds one sheet of paper. [FEED]
(2) Prints the data in the image buffer
on one label according to the
system mode setting.
(1) Resumes printing after a temporary
stop of label printing or after an
error.
(2) Places the printer in the usual initial
state which is obtained when the
power is turned on.
[RESTART]
(3) Switches to user mode.
(1) Stops label printing temporarily. [PAUSE]
(2) Programs the threshold values.
[MODE] (1) Switches to user mode.
[CANCEL] (1) Clears the job.
[ENTER] (1) Displays help messages.
[UP] (1) No function
[DOWN] (1) No function
[LEFT] (1) No function
[RIGHT] (1) Displays help messages.
1. OUTLINE SPTM-0152
1.3 APPEARANCE AND DIMENSIONS (APPROXIMATE)
1-3
1.3.3 Dimensions (Approximate)
Color : Metal cover: Cool Black Mold cover: Cool Black
Weight : B-EX4 T2 19.0Kg(acking condition) 17.0Kg(rinter only)
Outside dimension : Width 278mm x Depth 460mm x Hight 310mm
It is based on individual product specifications.
1. OUTLINE SPTM-0152
1.4 BASIC SPECIFICATIONS
1-4
1.4 BASIC SPECIFICATIONS
1) Printing method ................... Thermal direct printing or thermal transfer printing
2) Print head
[GS model]
(1) Total number of dots ...... 832 dots (3) Effective print width ....... 104.0 mm
(2) Dot density ..................... 8 dots/mm (4) Thermal pitch .......…...... 0.125 mm
[TS model]
(1) Total number of dots ...... 1,253 dots (3) Effective print width ....... 104.0 mm
(2) Dot density ..................... 11.8 dots/mm (4) Thermal pitch .......…...... 0.085 mm
[HS model]
3) Print speed
GS model ............................. 3”/sec., 6”/sec., 10”/sec. 12”/sec.
TS model.............................. 3”/sec., 5”/sec, 8”/sec., 10”/sec. 12”/sec.
[HS model]
NOTE: These print speeds are available when printing ratio is less than 15% of the entire label or tag
paper.
4) Format size (W) x (L)
GS model ............................. Max. 104.0 mm x 1500.0 mm
TS model.............................. Max. 104.0 mm x 1500.0 mm
[HS model]
5) Issue mode .......................... Batch
Cut (Option)
Peel-off (Option)
6) Type of bar code/two dimensional code
(1)
JAN8, EAN8, JAN13, EAN13, UPC-A, UPC-E
(13)
PDF417
(2)
EAN8, EAN13, UPC-A, UPC-E + 2digit
(14)
QR Code
(3)
EAN8, EAN13, UPC-A, UPC-E + 5digit
(15)
Industrial 2 of 5
(4)
NW-7
(16)
Customer Bar Code
(5)
CODE39 (STANDARD)
(17)
POSTNET
(6)
CODE39 (FULL ASCII)
(18)
RM4SCC
(7)
ITF
(Royal Mail 4 State Customer Code)
(8)
MSI
(19)
KIX CODE
(9)
CODE93
(20)
Maxi Code
(10)
CODE128
(21)
Micro PDF417
(11)
EAN128
(22)
CP CODE
(12)
Data Matrix
(23)
GS1 Databer
(The composite is included.)
7) Bar code rotation ................. 0°, 90°, 180°, 270°
1. OUTLINE SPTM-0152
1.4 BASIC SPECIFICATIONS
1-5
8) Type of characters
[GS model]
(1) Times Roman medium (12, 15 point) (12) Courier bold (18 point)
(2) Times Roman bold (15, 18, 21 point) (13) OCR-A, B (12 point)
(3) Times Roman Italic (18 point) (14) Outline font (Helvetica bold, Helvetica bold proportional,
(4) Helvetica medium (9, 15, 18 point) Price Font (1,2,3), Times roman proportional, Pop
(5) Helvetica bold (18, 21 point) Proportional, Proportional)
(6) Helvetica Italic (18 point) (15) Writable characters (2-byte character is available.)
(7) Presentation bold (27 point) (16) Gothic 725 black
(8)
(9)
Letter Gothic medium (14.3 point)
Prestige Elite medium (10.5 point)
(17)
(18)
China font (24x24) for CHINA model only
Mincho font (24x24, 32x32),
(10)
(11)
Prestige Elite bold (15 point)
Courier medium (15 point)
Gothic font (16x16, 24x24, 32x32, 48x48) for Japan
Model
[TS model]
(1) Times Roman medium (8, 10 point) (12) Courier bold (12 point)
(2) Times Roman bold (10, 12, 14 point) (13) OCR-A, B (12 point)
(3) Times Roman Italic (12 point) (14) Outline font (Helvetica bold, Helvetica bold proportional,
(4) Helvetica medium (6, 10, 12 point) Price Font (1,2,3), Times roman proportional, Pop
(5) Helvetica bold (12, 14 point) Proportional, Proportional)
(6) Helvetica Italic (12 point) (15) Writable characters (2-byte character is available.)
(7) Presentation bold (18 point) (16) Gothic 725 black
(8)
(9)
Letter Gothic medium (9.5 point)
Prestige Elite medium (7 point)
(17)
(18)
China font (24x24) for CHINA model only
Mincho font (24x24, 32x32),
(10)
(11)
Prestige Elite bold (10 point)
Courier medium (10 point)
Gothic font (16x16, 24x24, 32x32, 48x48) for Japan
Model
[HS model]
(1) Times Roman medium (8, 10 point) (12) Courier bold (12 point)
(2) Times Roman bold (10, 12, 14 point) (13) OCR-A, B (12 point)
(3) Times Roman Italic (12 point) (14) Outline font (Helvetica bold, Helvetica bold proportional,
(4) Helvetica medium (6, 10, 12 point) Price Font (1,2,3), Times roman proportional, Pop
(5) Helvetica bold (12, 14 point) Proportional, Proportional)
(6) Helvetica Italic (12 point) (15) Writable characters (2-byte character is available.)
(7) Presentation bold (18 point) (16) Gothic 725 black
(8)
(9)
Letter Gothic medium (9.5 point)
Prestige Elite medium (7 point)
(17)
(18)
China font (24x24) for CHINA model only
Mincho font (24x24, 32x32),
(10)
(11)
Prestige Elite bold (10 point)
Courier medium (10 point)
Gothic font (16x16, 24x24, 32x32, 48x48) for Japan
Model
9) Character code
(1) PC-850 (2) PC-8 (3) PC-852 (4) PC-857 (5) Arabic (6) LATIN 9 (7) PC-1257 (8) PC-1254
(9) PC-1253 (10) PC-1252 (11) PC-1251 (12) PC-1250 (13) PC-855 (14) PC-851 (15) UTF-8
(16) PC-866
10) Character magnification
(1) Regular font: 0.5 ~ 9.5 times (magnified by 0.5 times in each direction)
(2) Outline font: 2.0 ~ 150.0 mm (magnified 0.1 mm in each direction)
NOTE: When the outline font size is large, the ribbon may wrinkle according to the quality of the
ribbon or print tone.
11) White or black background all types of characters are available.
12) Character rotation ........................... 0
°, 90°, 180°, 270°
13) Character strings rotation ............... 0
°, 90°, 180°, 270°
14) Type of line
(1) Horizontal line (2) Vertical line (3) Slant line (4) Square (5) Rounded Rectangle (6) Circle
15) Line Width ....................................... 0.1 to 0.9 mm can be specified (in unit of 0.1 mm)
1. OUTLINE SPTM-0152
1.4 BASIC SPECIFICATIONS
1-6
16) Mechanism
(1) Mechanism
(2) Paper Sensor
Peel-off bar
13.75mm
Peel-off senso
r
15.3mm
Label sensor 77.25mm
Ribbon end sensor
47.4mm
Transmissive sensor
Reflect sensor
10mm
57mm
Paper left edge
1. OUTLINE SPTM-0152
1.4 BASIC SPECIFICATIONS
1-7
(3) Cutter mechanism
When the cutter module is installed, the backing paper of the label stock or tag paper is cut
individually.
Disk cutter: Stop and cut
Item Specification
Cutter type DISK CUTTER
Paper width 30.0mm -
Tag
25.4- 500mm
(T.B.D)
Cut
length
Label
38.0 - 1500mm
(T.B.D)
Possible
cut size
Thickness 80 - 170μm(T.B.D)
Cutter life 1,000,000 cut (160μm tag) (T.B.D)
* Cutter life is confirmed by using same width paper.
Disk Cutter:21.9
1. OUTLINE SPTM-0152
1.4 BASIC SPECIFICATIONS
1-8
17) Power supply
CN model: AC220 - 240 V ±10%, 50Hz
QM model: AC100 - 240 V ±10%, 50/60Hz
Global(QM) China(CN)
Input voltage/frequency
AC100V-240V
±10%
50-60Hz
AC100V-240V ±10%
50Hz
AC cord Not include Not include
100V: 22A
240V: 71A
240V: 71A Rush current
In order to exceed 10A, explane to users set up
exclusive plug socket.
Sleep
(Factory inital)
5.7W 0.09A 5.7W 0.09A
Stand-by
(Maximum)
Less than 8W (Print ready)
Less than 15W (Option full-operating)
Power
consumption
Operation *1 157.34W
2.0A-0.7A
157.34W
2.0A-0.7A
Power
supply
specification
Energy star appliance Yes
*1 An operation is a power consumption at the time of a 20% slant line.
(It is based on a specification test format.)
18) Current consumption
[B-EX4T2]
QM-R & CN-R model (100V) QM-R & CN-R model (240V)
Printing 166.31W,1.6888A 157.34W, 0.7147 A
Sleep mode 4.5W, 0.0893A 5.7W, 0.0861A
NOTES:
Be sure to provide an exclusive AC outlet for this machine. (This is 20% slant line print)
Energy Star Program appliance
19) Rush current
QM model: 100V: 22.1A, 240V: 70.6A
1. OUTLINE SPTM-0152
1.5 ELECTRONICS SPECIFICATIONS
1-9
1.5 ELECTRONICS SPECIFICATIONS
1) CPU ..................................... R8A77211C133BGV
2) Memory
(1) Program ............................ 2 x 16MB Flash ROM
(2) Image buffer + Work.......... 2 x 16MB SDRAM
Hardware
Model
Flash ROM SDRAM Font ROM Type Font
B-EX4T2-GS12-QM-R
B-EX4T2-TS12-QM-R
B-EX4T2-HS12-QM-R
None
B-EX4T1-GS12-CN-R
B-EX4T1-TS12-CN-R
B-EX4T1-HS12-CN-R
16MB 32MB
8MB
Simplified
Chinese
3) Interface
(1) USB
1) Standard: USB V2.0
2) Transfer mode: Control transfer, Bulk transfer
3) Transfer rate: Full speed (12M bps)
4) Class Printer class
5) USB interface Connector: USB-Type B
Power: Self-power
6) USB cable Type-A and Type-B cable of USB V2.0
(2) Wired LAN
1) Standard: IEEE802.3
2) Protocol: Physical layer: 10BASE-T, 100BASE-TX
Auto negotiation 10/100Mbps. Full/Half, Duplex
Data link layer: CSMA/CD
Network layer: IP, ICMP, ARP
Transport layer: TCP, UDP
Application layer: Server: LPR, SOCKET, HTTP, FTP
lient: POP3, SMTP, DHCP, WINS
Agent: SMMP
3) Network interface: Connector RJ-45
(3) RS-232C interface (Option)
1) Communication mode: Full-duplex
2) Transmission speed: 2400,4800,9600,19200, 38400, 115200 bps (selectable)
3) Asynchronous communication method
4) Transmission parameter
* Parity: None, EVEN, ODD
* Start bit: 1-bit
* Stop bit: 1-bit or 2-bit
* Word length: 7-bit or 8-bit
5) Error detection
* Parity check: VRC (Vertical Redundancy Checking)
* Framing error: This error occurs when no stop bit is found in the frame specified
starting with the start bit.
6) Data entry code: ASCII, 8-bit code for European characters, 8-bit code for graphic
7) Receiving buffer: B-EX4T: 6MB
1. OUTLINE SPTM-0152
1.5 ELECTRONICS SPECIFICATIONS
1-10
8) Protocol
* XON/XOFF (DC1/DC3) protocol
• When initialized after power on, this printer becomes ready to receive data and sends
an XON code (11H). (Transmission or non-transmission of XON code is selectable by
means of the parameter setting.)
• The printer sends an XOFF code (13H) when the free area in the receive buffer
becomes 10K Bytes or less.
• The printer sends an XON code (11H) when the free area in the receive buffer are
512KB or more.
• When there is no free area in the receive buffer, the printer discards received data
which exceeds the receive buffer capacity without storing it in the buffer. (After
detecting the XOFF code, the host computer must stop transmission before the printer
receive buffer becomes full.)
• The printer sends an XOFF code (13H) at power off time. (Transmission or nontransmission of XOFF code is selectable with the parameter setting.)
• The DTR signal is always “High” level (Ready).
• The RTS signal is always “High” level (Ready).
* READY/BUSY (DTR) protocol
• When initialized after power on, this printer becomes ready to receive data and
converts the DTR signal to "High" level (READY).
• The printer converts the DTR signal to "Low" level (BUSY) when the free area in the
receive buffer amount to 10K bytes or less.
• The printer converts the DTR signal to "High" level (READY) when the free area in the
receive buffer amount to 512KB or more.
• When there is no free area in the receive buffer, the printer discards received data
which exceeds the receive buffer capacity without storing it in the buffer. (After
detecting a BUSY signal, the host computer must stop transmission before the printer
receive buffer becomes full.)
• The RTS signal is always “High” level.
* XON/XOFF (DC1/DC3) protocol + READY/BUSY (DTR) protocol
• When initialized after power on, this printer becomes ready to receive data and
converts the DTR signal to "High" level (READY). The printer sends an XON code
(11H).
• When the free area in the receive buffer are 10K bytes or less, the printer converts the
DTR signal to "Low" level (BUSY) and sends an XOFF code (13H).
• When the free area in the receive buffer are 512KB or more, the printer converts the
DTR signal to "High" level (READY) and sends an XON code (11H).
• When there is no free area in the receive buffer, the printer discards received data
which exceeds the receive buffer capacity without storing it in the buffer. (After
detecting the XOFF code or BUSY signal, the host computer must stop transmission
before the printer receive buffer becomes full.)
• The printer sends an XOFF code (13H) at power off time.
• The RTS signal is always “High” level.
* READY/BUSY (RTS) Protocol
• When initialized after power on, this printer becomes ready to receive data and
converts the RTS signal to "High" level (READY).
• The printer converts the RTS signal to “Low” level (BUSY) when the free area in the
receive buffer amount to 10K bytes or less.
• The printer converts the RTS signal to “High” level (READY) when the free area in the
receive buffer amount to 512KB or more.
• When there is no free area in the receive buffer, the printer discards received data
which exceed the receive buffer capacity without storing it in the buffer. (After detecting
a BUSY signal, the host computer must stop transmission before the printer receive
buffer becomes full.)
• The DTR signal is always “High” level (READY).
• The host should keep the DSR signal “High” level.
NOTE: Be sure to select the READY/BUSY (RTS) protocol when controlling the flow
between the Windows. Also, be sure to select “Hardware” for the flow control in
the Windows communication port setting.
1. OUTLINE SPTM-0152
1.5 ELECTRONICS SPECIFICATIONS
1-11
9) Pin description
Pin No. Signal I/O Description
1 FG (Frame Ground) --- Ground line for circuit protection.
2 RD (Received Data) Input
Data line from which the printer receives data from
the host (receive data line).
Logic “1” is “Low”, and “0” is “High”. It is LOW
(MARK) while no data is being sent.
3 TD (Transmit Data) Output
Data line from which the printer sends data to the
host (send data line).
Logic “1” is “low”, and “0” is “High”. It is LOW
(MARK) while no data is being sent.
4 CTS (Clear to Send) Input
Input signal from the host. This printer ignores this
signal.
5 RTS (Request to Send) Output
Output signal to the host.
When READ/BUSY (RTS) protocol is selected,
this signal means READY to receive data.
When the receive buffer is nearly full, the signal
turns to “Low”, and “High” when nearly empty.
In case of other protocol is selected, this signal is
always “High” level after the power is turned on.
6
DTR (Data Terminal
Ready)
Output
Output signal from the printer.
When READY/BUSY (DTR) or XON/XOFF
(DC1/DC3)+READY/BUSY (DTR) is selected, this
signal means READY to receive data.
When the receive buffer is nearly full, the signal
turns to “Low”, and “High” when nearly eimpty.
In case of XON/XOFF (DC1/DC3) or READY/BUSY
(RTS), this signal is always “High” level after the
power is turned on.
7 SG (Signal Ground) --- Ground line for all data and control signals.
20 DSR (Data Set Ready) Input
Input signal from the host. It must be “High” for the
printer to receive data.
10) Interface circuit
* Circuit
* Signal level
Input voltage: "H" .. +2.4 V to + 25V Output voltage: "H" = MIN +5.0V, Typ. +5.4V
"L" ... –25V to 0.6V "L" = MIN -5.0V, Typ. -5.4V
1. OUTLINE SPTM-0152
1.5 ELECTRONICS SPECIFICATIONS
1-12
(4) Centronics interface (Option)
1) Data input method: 8-bit parallel (DATA 1 to 8)
2) Control signals
SPP mode: nStrobe, nAck, Busy, PError, Select, nAutoFd, nInit, nFault,
nSelectIn
Nibble mode: HostClk, PtrClk, PtrBusy, AckDataReq, Xflag, HostBusy, nInit,
nDataAvail, IEEE1284Active
3) Data input code: ASCII, JIS 8-bit code for European characters, 8-bit code for
graphic
4) Receiving buffer: 6MB (Max. 65536 lines)
5) Input/Output circuit configuration and Input/Output conditions
Connector
Amp. Japan 552742-1 or equivalent
Printer side: DDK 57RE-40360-73B or equivalent
Amp. Japan 552470-1 or equivalent
Cable side:
DDK 57E-30360 or equivalent
1. OUTLINE SPTM-0152
1.5 ELECTRONICS SPECIFICATIONS
1-13
(5) Expansion I/O interface (Option)
Interface circuit
* Input circuit
There are 6 input circuits, and each input is a current loop using the photo coupler. The anode
of the photo coupler of each circuit is connected to the common pin COM 1. The cathodes are
independent. The voltage of Vcc is 5 to 24 V, while the diode operating current is 16 mA
(average).
* Output circuit
There are 7 output circuits, and each output is an open collector. The voltage of Vcc is 5 to 24 V,
while the drive current is 150 mA (max.).
For other details, please refer to the Expansion I/O specifications stored in the enclosed CDROM or posted on the web site with the URL, http://barcode.toshibatec.co.jp.
1. OUTLINE SPTM-0152
1.5 ELECTRONICS SPECIFICATIONS
1-14
(6) USBH (Option)
1) Standard: USB V2.0
2) Transfer mode: Control transfer, Bulk transfer
3) Transfer rate: Full speed (12M bps)
4) USB interface Connector: USB-Type A
Power supply specification: 500mA output
(7) Wireless LAN (Option)
1) Standard: IEEE802.11b/g
2) Protocol: Physical layer: 802.11b/g
Date link layer: CSMA/CA
Network layer: IP, ICMP, ARP
Transport layer: TCP, UDP
Application layer: Server: LPR, SOCKET, HTTP, FTP
Client: POP3, SMTP, DHCP, WINS
Agent: SNMP
Security: IEEE802.11i
Encryption: WEP (64/128bit), TKIP (WPA), AES
(WPA2)
Authentication: Shared key (for WEP), PSK, PEAP, TLS,
TTLS, MD5, LEAP, EAP-FAST
3)
Communicable distance: Class1, 100m (When there is no obstacle),
360 deg. (depending on conditions)
4) Antenna: Built-in (Not available for external antenna)
5) Certification: WiFi, CCX V3, V4
4) Sensor/switch
Transmittive sensor Transmittive (Movable/Adjustable)
Refrective sensor Refrective (Movable/Adjustable)
Outer temperature sensor Detect range: 0 to 70°C
Head temperature sensor Detect range 0 to 80°C
Head up sensor Optical slit sensor
Ribbon rotation detect sensor Optical slit sensor (Ribbon diameter detection for rewinder, back
tension block)
Ribbon end sensor Refrective (Detect silver area of ribbon end tape)
2. SUPPLY SPECIFICATIONS SPTM-0152
2.1 MEDIA (Paper)
2-1
2. SUPPLY SPECIFICATIONS
Information regarding the supply specifications contained in Product Description is essential to service
engineers. Detail specifications and other information on the media and ribbon are described in Supply
Manual by model. It is issued by and sent from TOSHIBA TEC H.Q (Sales Division) upon release of
new model or manual's revision. When purchasing the supplies locally, be sure to refer to the Supply
Manual for details. Use of non-specified media may shorten the print head life and result in problems
with bar code readability or print quality. Be sure to read carefully and understand the Supply Manual
since it also includes the details about notes, precision of the print start position, limitations on printing,
etc. When selling the products to VARs, instruct them to buy media and ribbons that the substances
described in the following precautions are not included.
2.1 MEDIA (Paper)
2.1.1 Types of paper
Two types of paper are available, labels and tags, each being further divided into the direct
thermal type and thermal transfer type. The approved paper must be used.
Use of any non-approval paper may cause problems.
2.1.2 Paper Size and Shape
Item B-EX4T2
Thermal head density 8dots/mm (203dpi) 11.8dots/mm (300dpi) 23.6dots/mm (600dpi)
Thermal head width 104.0mm 108.416mm 105.58mm
Contents Issue type Batch
Strip
*Note1
Disc
Cutter
Batch
Strip
*Note1
Disc
Cutter
Batch Strip
Disc
Cutter
Min. 10.0 25.4 25.4 10.0 25.4 25.4 8.0 25.4 25.4
Label
Max. 1500.0 256.0 1500.0 1500.0 256.0 1500.0 500.0 256.0 500.0
Min. 10.0 － 25.4 10.0 － 25.4 10.0 － 25.4
A:
Paper
Pitch
Tag
Max. 1500.0 － 1500.0 1500.0 － 1500.0 500.0 － 500.0
Min. 8.0 23.4
23.4
*Note2
8.0 23.4
23.4
*Note2
6.0 23.4
23.4
*Note2
B: Paper length
Max. 1498.0 254.0 1494.0 1498.0 254.0 1494.0 498.0 254.0 494.0
Min. 30.0 50.0 30.0 30.0 50.0 30.0 30.0 50.0 30.0
C:
Tag width
Backing
paper width
Max. 114.0 114.0 114.0
Min. 27.0 27.0 27.0
D: Label width
Max. 111.0 111.0 111.0
Min. 2.0 6.0 2.0 6.0 2.0 6.0
E:
Label-to-label
gap
Max. 20.0 20.0 20.0
Min. 2.0 2.0 2.0
F:
Black mark
length
Max. 10.0 10.0 10.0
G: Max. effective
print width
Max. 104.0 +-0.2 104.0 +-0.2 104.0 +-0.2
Min. 6.0 21.4 21.4 6.0 21.4 21.4 6.0 21.4 21.4
Label
Max. 1496.0 252.0 1492.0 1496.0 252.0 1492.0 496.0 252.0 492.0
Min. 8.0 － 21.4 8.0 － 21.4 8.0 － 21.4
H:
Effective print
length
Tag
Max. 1498.0 － 1498.0 1498.0 － 1498.0 498.0 － 498.0
Slow-up 1.0 1.0 1.0
I:
Slow-up and
down area
(Un-print
area)
Slow-down 1.0 1.0 1.0
Min. 0.13 0.13 0.13
J:
Paper
thickness
Max. 0.17 0.17 0.17
K: Max. on-the-fly printing length 749.0 749.0 249.0
L: Max. paper roll diameter
φ200
(Using external rewinder φ180)
φ200
(Using external rewinder φ180)
φ200
(Using external rewinder φ180)
M
:
Paper winding direction
Inside the printing side
(STD.)
Inside the printing side
(STD.)
Inside the printing side
(STD.)
N: Paper core
Inside diameter
φ76.2±0.3
Inside diameter
φ76.2±0.3
Inside diameter
φ76.2±0.3
*Note1: When using the peel-off at 12”/sec or more for 203dpi model, issue at 10”/sec.
When using the peel-off at 10”/sec or more for 300dpi model, issue at 8”/sec.
*Note2: When using the disk cutter, the label length must meet the following condition:
Label length
≧
18.0mm - (Gap length/2).
2. SUPPLY SPECIFICATIONS SPTM-0152
2.1 MEDIA (Paper)
2-2
Feed direction
Ｉ
Ｈ
B
E
G
D
C
A
F
A
C
G
B
Feed direction
Black Mark(Reverse Side）
Roll method: Labels facing inside
Roll method: Labels facing outside
Roll method: Tag facing inside
Roll method: Tags facing outside
K
K
J
J
<Labels>
<Tags>
K
J
K
J
Loading...