Input Signal Selection.......................... 61
Specications and
Accessories ...............................62
4
Safety Precautions
This equipment has been designed and manufactured to meet international safety standards but, like
any electrical equipment, care must be taken to obtain the best results and for safety to be assured.
Please read the points below for your own safety. They are of a general nature, intended to help with all
electronic consumer products and some points may not apply to the goods you have just purchased.
The Class I apparatus shall be connected to a mains socket outlet with a protective earthing
connection.
English
Leave more than 10cm clearance around the
Air Circulation
television to allow adequate ventilation. This
will prevent overheating and possible damage
to the television. Dusty places should also be
avoided.
Heat Damage
Damage may occur if the television is left in
direct sunlight or near a heater. Avoid places
subject to extremely high temperatures or
humidity. Place in a location where the temperature remains between 5°C (41°F) min. and
35°C (94°F) max.
Mains Supply
The mains supply required for this equipment
is 220-240v AC 50/60Hz. Never connect to a
DC supply or any other power source. DO ensure that the television is not standing on the
mains lead. Use only the supplied lead.
DO NOT cut off the mains plug from this
equipment, this incorporates a special Radio
Interference Filter, the removal of which will
impair its performance. In the UK, the fuse
tted in this plug is approved by ASTA or BSI
to BS1362.
It should only be replaced by a correctly rated
and approved type and the fuse cover must be
retted.
IF IN DOUBT PLEASE CONSULT A COMPETENT ELECTRICIAN.
Do
DO read the operating instructions before you
attempt to use the equipment.
DO ensure that all electrical connections
(including the mains plug, extension leads and
inter-connections between pieces of equipment) are properly made and in accordance
with the manufacturers’ instructions. Switch off
and withdraw the mains plug before making or
changing connections.
DO consult your dealer if you are ever in doubt
about the installation, operation or safety of
your equipment.
DO be careful with glass panels on equipment.
DO NOT REMOVE ANY FIXED COVERS
AS THIS WILL EXPOSE DANGEROUS AND
‘LIVE’ PARTS.
THE MAINS PLUG IS USED AS A DISCONNECTING DEVICE AND THEREFORE
SHOULD BE READILY OPERABLE.
Do not
DO NOT obstruct the ventilation openings of
the equipment with items such as newspapers,
tablecloths, curtains, etc. Overheating will cause
damage and shorten the life of the equipment.
DO NOT allow electrical equipment to be
exposed to dripping or splashing or objects lled
with liquids, such as vases, to be placed on the
equipment.
DO NOT place hot objects or naked ame
sources, such as lighted candles or nightlights
on, or close to equipment. High temperatures
can melt plastic and lead to res.
DO NOT use makeshift stands and NEVER
x legs with wood screws. To ensure complete
safety, always t the manufacturers’ approved
stand, bracket or legs with the xings provided
according to the instructions.
DO NOT leave equipment switched on when
it is unattended, unless it is specically stated
that it is designed for unattended operation or
has a standby mode. Switch off by withdrawing
the plug, make sure your family know how to
do this. Special arrangements may need to be
made for people with disabilities.
DO NOT continue to operate the equipment if
you are in any doubt about it working normally,
or it is damaged in any way – switch off, withdraw the mains plug and consult your dealer.
WARNING – excessive sound pressure from earphones or headphones can cause hearing loss.
ABOVE ALL – NEVER let anyone, especially children, push or hit the screen, push anything into
holes, slots or any other openings in the case.
NEVER guess or take chances with electrical
equipment of any kind – it is better to be safe
than sorry.
5
English
Locate the television away from direct sunlight and
strong lights, soft, indirect lighting is recommended for
comfortable viewing. Use curtains or blinds to prevent
direct sunlight falling on the screen.
Place the TV set on a stable, level surface that
can support the weight of the TV. As an additional
safety measure you secure the TV to the level
surface or a wall, as shown in the illustration, using
sturdy strap.
The LCD display panels are manufactured using
an extremely high level of precision technology,
however sometimes some parts of the screen may
be missing picture elements or have luminous
spots. This is not a sign of a malfunction.
Make sure the television is located in a position
where it cannot be pushed or hit by objects, as
pressure will break or damage the screen. Also,
please be certain that small items cannot be inserted into slots or openings in the case.
Cleaning the screen and cabinet...
Turn off the power, and clean the screen and cabinet
with a soft, dry cloth. We recommend that you do not
use any proprietary polishes or solvents on the screen
or cabinet as this may cause damage.
Please use a wall bracket appropriate for the size and weight of the LCD TV.
• Two people are required for installation.
• Never use the four screws attached to the TV.
• To install a wall-mount from another manufacturer, use the SPACERS (supplied).
1. Unplug and remove any cables and/or other
component connectors from the rear of the TV.
2. Carefully lay the front of the unit face down on a at,
cushioned surface such as a quilt or blanket.
3. Follow the instructions provided with your wall
bracket. Before proceeding, make sure the appropriate bracket(s) are attached to the wall and
the back of the TV as described in the instructions provided with the wall bracket.
4. Make sure to place the spacers supplied between the bracket and the back of the TV.
5. Always use the screws supplied or recommended by the wall mount manufacturer.
*Screw Type for Wall Bracket:
• 26LED, 32CCFL, 32LED, 40CCFL: M6/10mm/20KG
• 42LED: M8/12mm/20KG
Where to install
Fixing strap
Fixing strap
Fixing strap
Fixing strap
Stand style is dependent on model
When using a Wall Bracket
Installation and important information
Sturdy tie (as short as possible)
Sturdy tie (as short as possible)
Remove four screws.
(Do not reuse these screws for
attaching a wall bracket.)
Place four spacers (supplied).
Remove four screws.
(Do not reuse these screws for
attaching a wall bracket.)
Place four spacers (supplied).
Stand clip
Stand clip
Screw
Wall bracket
Spacer
(supplied)
TV back panel
Screw
Wall bracket
Spacer
(supplied)
TV back panel
6
Removing the Pedestal Stand:
1. Carefully lay the front of the unit face down on a
at, cushioned surface such as a quilt or a blanket. Leave the stand protruding over the edge of
the surface.
NOTE: Extreme care should always be used when
removing the pedestal stand to avoid damage to the LCD panel.
2. Remove the screws.
3. Once you have removed all ve screws
holding the pedestal stand in place, remove
the pedestal stand from the TV by sliding the
pedestal stand away from the TV.
Please take note
EXCLUSION CLAUSE
Toshiba shall under no circumstances be liable for loss and/or damage to the product caused by:
i) re;
ii) earthquake;
iii) accidental damage;
iv) intentional misuse of the product;
v) use of the product in improper conditions;
vi) loss and/or damage caused to the product while in the possession of a third party;
any damage or loss caused as a result of the owner’s failure and/or neglect to follow the in-
vii)
structions set out in the owner’s manual;
any loss or damage caused directly as a result of misuse or malfunction of the product when
viii)
used simultaneously with associated equipment;
Furthermore, under no circumstances shall Toshiba be liable for any consequential loss and/or
damage including but not limited to the following, loss of prot, interruption of business, the loss of
recorded data whether caused during normal operation or misuse of the product.
• If stationary images generated by 4:3 broadcasts, text services, channel identication logos, computer
displays, video games, on-screen menus, etc. are left on the television-screen for any length of time they
could become conspicuous, it is always advisable to reduce both the brightness and contrast settings.
• Very long, continuous use of the 4:3 picture on a 16:9 screen may result in some retention of the
image at the 4:3 outlines, this is not a defect of the LCD TV and is not covered under the manufacturers warranty. Regular use of other size modes (e.g.: Superlive) will prevent permanent retention.
NOTE: Interactive video games that involve shooting a “gun” type of joystick at an on-screen target
may not work with this TV.
English
SYMBOLSYMBOL DEFINITION
DANGEROUS VOLTAGE: The lightening ash with arrowhead symbol within an
equilateral triangle is intended to alert the user to the presence of un-insulated
“DANGEROUS VOLTAGE” within the product’s enclosure that may be of sufcient
magnitude to constitute a risk of electric shock to persons.
INSTRUCTIONS: The exclamation point within on equilateral triangle to alert the
user to the presence of important operating and maintenance (servicing) instruction
in the literature accompanying the appliance.
WARNING: To prevent the spread of re, keep candles or other open ames away
from this product at all times.
7
EnglishEnglish
English
When does switchover happen?
*Copeland switches on October 17, 2007
Keep this important
information about
The exact date you
switch depends on the
transmitter you are
how to re-tune your
served by. To check
when you switch,
go to Digital UK’s
postcode checker on
TV during the
www.digitaluk.co.uk
Check your ITV news
service or look at Teletext
TV switchover
page 106 to see what TV
region you’re in.
Television in the UK is going digital, bringing
us all more choice and new services. Starting
in late 2007 and ending in 2012, television
services in the UK will go completely digital, TV
region by TV region.
Please see above to nd out when your area
switches to digital.
Digital UK is the independent, non-prot
organisation leading the process of digital
TV switchover in the UK. Digital UK provides
impartial information on what people need to
do to prepare for the move to digital, and when
they need to do it.
How the switchover affects your TV
equipment:
Your new TV has a digital tuner built in, which
means it is ready to receive the Freeview signal by simply plugging it into your aerial socket
(check if you can get digital TV through your
aerial now, or whether you’ll have to wait until
switchover, at www.digitaluk.co.uk).
When the TV switchover happens in your area,
there are at least two occasions when you will
need to re-tune your TV in order to continue receiving your existing TV channels, and also to
pick up new ones, Digital UK, the body leading
the digital TV switchover, will advise you when
you need to re-tune during the switchover.
If you choose to connect your TV to satellite
or cable with a digital box then it will not be
affected by switchover, and you won’t need to
re-tune.
Digital Switchover
Keep this important
EnglishEnglish
information about
how to re-tune your
TV during the
TV switchover
How to re-tune:
As new services are broadcast it will be necessary to re-tune the television in order to view
them. Auto tuning will completely retune the
television and can be used to update the channel list.
Press MENU button on the remote
control unit.
Select Auto tuning option.
A screen will appear warning that previous digital programmes and settings will
be deleted.
You must allow the television to com-
plete the search......
When the search is complete the Auto tuning
screen will display the total number of service
found.
Note:
Further detailed instructions on Auto tuning
can be found in the TV owners manual.
If you are missing channels, it may be that
they are not available in your area, or that your
aerial needs upgrading.
If you have any further questions, please
contact your equipment supplier or call Digital
UK on 08456 50 50 50 or visit www.digitaluk.
co.uk
8
digital
English
PICTURE SOUND
SETUP
APPLICATIONS PREFERENCES
Language
Country
Tuner Mode
Auto tuning
ATV Manual Tuning
DTV Manual Tuning
DTV Settings
AV connection
Picture Position
Quick Setup
English
UK
Antenna
Enter
OK
Back
RETURN
1/2SET UP
OK
OK
OK
OK
OK
Auto tuning
Tuning Mode
Start Scan
ATV and DTV
OK
Back
RETURN
Previous settings will be lost !
Press EXIT for no change.
Enter
OK
Auto tuning
ATV
DTV
Stop
EXIT
Progress
2 %
0 %
Channel: C4 Station:
Found
0
0
Re-tuning: TOSHIBA
Freeview products
4 Steps
(Steps 1-4)
This guide can be used to help you re-tune the following product with the remote control below:
TOSHIBA Digital TV
1 )
Make sure your TV is on and press 80
for the BBC News channel
Press MENU and press ◄ or ► to select SETUP.
2222
1
Press ▲ or ▼ to select
2 )
1
2
1
Auto tuning, and press
to enter the sub-
menu.
Press ▲ or ▼ to select
3 )
1
22
1
1
2
1
TOSHIBA Customer Helpline: 0844 856 0730
* This process may affect any saved information stored on your product, including your favourites list.
Please consult your instruction manual or contact the manufacturer using the details above.
Tuning Mode and press
◄ or ► to select ATV ,
DTV or ATV and DTV.
If you are comfortable with technical information and your basic re-tune hasn’t worked,
you can use this manual re-tune guide.
If your Freeview TV or box picks up a di erent regional service to your
preferred service (e.g. BBC England instead of BBC Scotland, or ITV Central
instead of ITV Anglia), you can use this manual re-tune guide.
800 or above, this guide will help you put them in your preferred position.
retailer or installer. This is a guide only, Freeview models operate slightly
di erently. Some early models do not o er a manual re -tune facility –
check your instruction book.
Go to the Postcode Checker at digitaluk.co.uk
1
Enter your postcode on the right hand side of the web page.
Remember to include your house number or name.
If you do not have internet access, contact the Digital UK
helpline on 08456 50 50 50
guide support.
Once you have entered your address details, the next page gives you an indication of
which TV services you should receive, based on your most likely transmitter. You may
2
be able to receive television services from more than one transmitter and you can
check alternatives, where available.
On the results page click on the pink button to see
your full reception forecast and channel information
for switchover.
*
and ask for manual re-tune
Please note:
Every time
you re-tune,
you will need
to go through
this process.
Click on the How do I re-tune? pink banner.
3
Scroll down to the manual re-tune table where
you will see the relevant “RF Channel” numbers
for the digital services that can be received
at your home.
Write down the “RF Channel” numbers
for your transmitter using the Group
4
boxes here:
*Calls are free for BT customers within inclusive calling plans. Call charges from other providers may vary. The standard business hours for Digital UK’s contact centre are 9am to 7pm
Monday to Friday and 10am to 4pm on a Saturday. Opening hours will be extended during switchover in each area. Digital UK, PO Box 26833, Kirkcaldy,KY2 9AG .
**Please note that the Freeview channel line-up is subject to change.
**
Group 1
Group 2
Group 3
Group 4
Group 5
Group 6
10
English
Language
Country
Tuner Mode
Auto tuning
ATV Manual Tuning
DTV Manual Tuning
DTV Settings
AV connection
Picture Position
Quick Setup
OK
Enter
DTV Manual Tuning
WeakAverageStrong
Signal Strength
Quality
RF Channel
Start Scan
0−9
Poor
1/2SET UP
English
UK
Antenna
OK
OK
OK
OK
OK
RETURN
Back
5
OK
RETURN
EditInput
Back
11
English
Simple at-a-glance reference of your remote
control.
The Remote Control
12 In TV mode: Display on-screen information
In Text mode: Access the index page
13 Mute the sound
14 Display the QUICK access menu
15 Exit the menu system
16 Display EPG
17 Go to the previous level of the menu
18 Display the on-screen menu
19 Menu navigation: ▲, ▼, ◄, ►:
In Text mode: Change the page
Conrm the selection
20 Colour button: Text control buttons
Reveal concealed text
Hold a wanted page
Enlarge text display size
Select a page while viewing a
normal picture
Inserting batteries and
effective range of the remote
Remove the back
cover to reveal the
battery compartment
and make sure the
batteries are inserted
the right way round.
Suitable battery types
for this remote are
AAA, 1.5V.
1 Toggle between TV ON or Standby
2 Toggle between external input sources
3 Still Picture
4 To display the teletext screen
5 TEXT subtitle pages if available
6 Stereo/Bilingual transmissions
7 Number buttons
8 Audio Description
9 Switch between ATV and DTV
10 Change the volume
11 Change the channel
Do not combine a used, old battery with a new
one or mix battery types. Remove dead batteries
immediately to prevent acid from leaking into
the battery compartment. Dispose of them in
accordance with instructions on page 64 of this
manual. Warning: batteries must not be exposed
to excessive heat such as sunlight or re.
The performance of the remote control will
deteriorate beyond a distance of ve metres or
outside an angle of 30 degrees from the centre
of the television. If the operating range becomes
reduced the batteries may need replacing.
12
Connecting External Equipment
HDMI 1 INPUT
SOCKET
RGB/ PC
AC−IN
HDMI 2 INPUT
SOCKET
HDMI 1 INPUT
SOCKET
RGB/ PC
HDMI 2 INPUT
SOCKET
AC−IN
Before connecting any external equipment, turn off all main power switches. If there is no switch
remove the mains plug from the wall socket.
Connect the power cord into the AC-IN socket found at the back of the TV.
Connect the video recorder IN/OUT or decoder TV socket to the television. Connect the media player
SAT socket to the decoder MEDIA REC. socket.
Before running Auto Tuning put your decoder and media recorder to Standby.
HDMI® (High-Denition Multimedia Interface) is for use with a DVD, decoder or electrical equipment
with digital audio and video output. It is designed for best performance with 1080i high-denition video
signals but will also accept and display 480i, 480p, 576i, 576p, 720p and 1080p. HDMI1 also support
VGA, SVGA, XGA, WXGA and SXGA.
NOTE: Although this television is able to connect to HDMI equipment it is possible that some equip-
ment may not operate correctly.
A wide variety of external equipment can be connected to the back of the television, therefore
the relevant owners manuals for all additional equipment must be referred to.
If the television automatically switches over to monitor external equipment, return to normal television
by pressing the desired channel button. To recall external equipment, press to select.
HDMI, the HDMI Logo, and High-Denition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the
United States and other countries.
NOTE: Because there is possibility to happen unexpected phenomenon, power cord should not be
disconnected frequently.
14
HDMI-LINK Connections
The basic functions of connected audio/video equipment can be controlled using the television’s
remote control if a HDMI-LINK compatible device is connected.
The back of your television
English
AV amplifier
AV amplifier
HDMI outHDMI in
Playback equipment
HDMI out
For 26/32EL83*B | 32/42HL83*B
The back of your television
HDMI outHDMI in
Playback equipment
HDMI out
Playback equipment
HDMI out
Playback equipment
HDMI out
For 32AV83*B | 32/40LV83*B
15
Connecting an HDMI or DVI device to the HDMI input
HDMI
cable
HDMI device
HDMI out
(not supplied)
English
The HDMI input on your television receives digital audio and uncompressed digital video from an
HDMI source device or uncompressed digital video from a DVI (Digital Visual Interface) source device.
This input is designed to accept HDCP (High-Bandwidth Digital-Content Protection) programme material in digital form from EIA/CEA-861-D–compliant [1] consumer electronic devices (such as a set-top
box or DVD player with HDMI or DVI output). For acceptable video signal formats, see page 22.
NOTE:
• Some early HDMI equipment may not work properly with your latest HDMI TV, due to the
adoption of a new standard.
• Supported Audio format: Linear PCM, sampling rate 32/44.1/48kHz.
To connect an HDMI device
Connect an HDMI cable (type A connector) from the device to the HDMI terminal.
For proper operation, it is recommended that you use an HDMI cable with the HDMI Logo
().
• If your HDMI connection is capable of 1080p and/or your television is capable of refresh rates
greater than 50Hz, you will need a Category 2 cable. Conventional HDMI/DVI cable may not work
properly with this mode.
• HDMI cable transfers both video and audio. Separate analogue audio cables are not required
(see illustration).
For 26/32EL83*B | 32/42HL83*B
16
English
HDMI
cable
HDMI device
HDMI out
(not supplied)
For 32AV83*B | 32/40LV83*B
To view the HDMI device video, press the button to select HDMI 1 or HDMI 2 mode.
17
English
DVI device
HDMI-to-DVI adapter cable
(not supplied)
Audio cable for HDMI
to television connection
(not supplied)
Connect an HDMI-to-DVI adapter cable (HDMI type A connector) to the HDMI 1 terminal and audio
cables to the PC/HDMI1 (AUDIO) socket (see illustration).
• The recommended HDMI-to-DVI adapter cable length is 6.6ft (2m).
• An HDMI-to-DVI adapter cable transfers video only.
• Separate analogue audio cables are required for audio receivers.
To connect a DVI device
For 26/32EL83*B | 32/42HL83*B
18
English
DVI device
HDMI-to-DVI adapter cable
(not supplied)
Audio cable for HDMI
to television connection
(not supplied)
For 32AV83*B | 32/40LV83*B
To ensure that the HDMI or DVI device is reset properly, it is recommended that you follow these
procedures:
• When turning on your electronic components, turn on the television rst, and then the HDMI or
DVI device.
• When turning off your electronic components, turn off the HDMI or DVI device rst, and then the
television.
[1] EIA/CEA-861-D compliance covers the transmission of uncompressed digital video with high-bandwidth digital content protection,
which is being standardized for reception of high-denition video signals. Because this is an evolving technology, it is possible that
some devices may not operate properly with the television.
HDMI, the HDMI Logo, and High-Denition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in
the United States and other countries.
19
English
the back of your television
HDMI-to-DVI
adapter cable
(not supplied)
2
Computer
Audio cable for PC to television
connection (not supplied)
Connecting a Computer
With either an RGB/PC or an HDMI connection, you can watch your computer’s display on the television and hear the sound from the televisions speakers.
To connect a PC to the HDMI terminal
When connecting a PC to the HDMI terminal on the television, use an HDMI-to-DVI adapter cable
and an analogue audio cable.
If connecting a PC with an HDMI terminal, use an HDMI cable (type A connector). A separate analogue cable is not necessary.
For 26/32EL83*B | 32/42HL83*B
20
Loading...
+ 44 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.