Toshiba a300, a300d User Manual

User’s Manual

A300/A300D

computers.toshiba-europe.com

Copyright

A300/A300D

© 2008 by TOSHIBA Corporation. All rights reserved. Under the copyright
laws, this manual cannot be reproduced in any form without the prior
written permission of TOSHIBA. No patent liability is assumed, with respect
to the use of the information contained herein.

TOSHIBA A300/A300D Portable Personal Computer User's Manual

First edition February 2008
Ownership and copyright of music, video, computer programs, databases,

etc. are protected by the copyright laws. These copyrighted materials may
be copied for private use at home only. If, beyond the limitation above, you
copy (including to transform data formats) or modify these materials,
transfer them or distribute them via the Internet without approval of
copyright owners, you may be subject to claims for compensation for
damage and/or criminal penalties due to infringements of copyrights or
personal rights. Please remember to observe the copyright laws when you
use this product to copy the copyrighted works or perform other actions.

Please note that you may infringe the owner's rights protected by the
copyright laws if you use the screen mode switching functions (e.g. Wide
mode, Wide Zoom mode, etc.) of this product to display enlarged
images/video at coffee shops or hotels for the purposes of profits or
providing these to the public.

This product incorporates copyright protection technology that is protected
by U.S. patents and other intellectual property rights. Use of this copyright
protection technology must be authorized by Macrovision, and is intended
for home and other limited viewing uses only unless otherwise authorized
by Macrovision. Reverse engineering or disassembly is prohibited.

Disclaimer

This manual has been validated and reviewed for accuracy. The
instructions and descriptions it contains are accurate for the A300/A300D
Portable Personal Computer at the time of this manual’s production.
However, succeeding computers and manuals are subject to change
without notice. TOSHIBA assumes no liability for damages incurred directly
or indirectly from errors, omissions or discrepancies between the computer
and the manual.

Trademarks

Microsoft, Windows and Windows Vista are either registered trademarks or
trademarks of Microsoft Corporation.

DirectX, AcriveDesktop, DirectShow, and Windows Media are registered
trademarks of Microsoft Corporation.

Intel, Intel Core, Celeron, Centrino and Pentium are trademarks or
registered trademarks of Intel Corporation.

User’s Manual ii

A300/A300D

AMD, the AMD Arrow logo, AMD Athlon, AMD Turion, Radeon, and
combinations thereof, ATI Mobility Radeon are trademarks of Advanced
Micro Devices, Inc.

Adobe and Photoshop are either registered trademarks or trademarks of
Adobe Systems Incorporated.

Bluetooth is a registered trademark owned by its proprietor and used by
TOSHIBA under license.

ConfigFree is a trademark of TOSHIBA Corporation.
The HD DVD Logo is a trademark of DVD Format/Logo Licensing

Corporation.
DVD MovieFactory is a trademark of the Ulead Systems, Inc.
BizCard is a trademark of NewSoft Technology Corporation.
Dolby is a registered trademark of Dolby Laboratories.
ExpressCard is a trademark of PCMCIA.
HDMI, the HDMI logo and High-Definition Multimedia Interface are

trademarks or registered trademarks of HDMI Licensing LLC.
Labelflash is a trademark of YAMAHA CORPORATION.
Memory Stick, Memory Stick PRO, and i.LINK are registered trademarks

and i.LINK is a trademark of SonyCorporation.
MultiMediaCard and MMC are trademarks of MultiMediaCard Association.
Photo CD is a trademark of Eastman Kodak.
Secure Digital and SD are trademarks of SD Card Association.
xD-Picture Card is a trademark of Fuji Photo Film, Co., Ltd.
Wi-Fi is a registered trademark of the Wi-Fi Alliance.
Other trademarks and registered trademarks not listed above may be used

in this manual.

Safety lnstructions

Use the following safety guidelines to help protect yourself and your
computer.

When Using Your Computer

Do not operate your portable computer for an extended period of time wite
the base resting directly on your body. With extended operation, heat can
potentially build up in the base. Allowing sustained contact with the skin
could cause discomfort or, eventually, a burn.

■ Do not attempt to service the computer yourself. Always follow

installation instructions closely.

■ Do not carry a battery in your pocket, purse, or other container where

metal objects (such as car keys) could short-circuit the battery
terminals. The resulting excessive current follow can cause extremely
high temperatures and may result in damage from burns.

User’s Manual iii

A300/A300D

■ Be sure that noting rests on your AC adapter's power cable and that the

cable is not located where it can be tripped over or stepped on.

■ Place the AC adapter in a ventilated area, such as a desk top or on the

floor, when you use it to run the computer or to charge the battery. Do
not cover the AC adapter with papers or other items that will reduce
cooling; also, do not use the AC adapter while it is inside a carrying
case.

■ Use only the AC adapter and batteries that are approved for use with

this computer. Use of another type of battery or AC adapter may risk fire
or explosion.

■ Before you connect the computer to a power source, ensure that the

voltage rating of the AC adapter matches that of the available power
source. 115V/60 Hz in most of North and South America and some Far
Eastern countries such as Taiwan. 100 V/50 Hz in eastern Japan and
100 V/60 Hz in westem Japan. 230 V/50 Hz in most of Europe, the
Middle East, and the Far East.

■ If you use an extension cable with your AC adapter, ensure that the total

ampere rating of the products plugged in to the extension cable does
not exceed the ampere rating of the extension cable.

■ To remove power form the computer, turn it off, remove the battery, and

disconnect the AC adapter from the electrical outlet.

■ To help avoid the potential hazard of electric shock, do not connect or

disconnect any cables or perform maintenance or reconfiguration of this
product during an electrical storm.

■ When setting up the computer for work, place it on a level surface.

EU Declaration of Conformity

This product is carrying the CE-Mark in accordance with the related
European Directives. Responsible for CE-Marking is TOSHIBA Europe
GmbH, Hammfelddamm 8, 41460 Neuss, Germany.

The complete and official EU Declaration of Conformity can be found on
TOSHIBA’s web site http://epps.toshiba-teg.com on the Internet.

CE compliance

This product is labelled with the CE Mark in accordance with the related
European Directives, notably Electromagnetic Compatibility Directive
89/336/EEC for the notebook and the electronic accessories including the
supplied power adapter, the Radio Equipment and Telecommunications
Terminal Equipment Directive 1999/5/EC in case of implemented
telecommunication accessories and the Low Voltage Directive 73/23/EEC
for the supplied power adapter.

User’s Manual iv

This product and the original options are designed to observe the related
EMC (Electromagnetic Compatibility) and safety standards. However,
TOSHIBA cannot guarantee that this product still observes these EMC
standards if options or cables not produced by TOSHIBA are connected or
implemented. In this case the persons who have connected/implemented
those options/cables have to provide assurance that the system (PC plus
options/cables) still fulfils the required standards. To avoid general EMC
problems, the following guidance should be noted:

■ Only CE marked options should be connected/implemented

■ Only the best shielded cables should be connected

Working environment

This product was designed to fulfil the EMC (Electromagnetic Compatibility)
requirements to be observed for so-called "Residential, commercial and
light industry environments".

TOSHIBA do not approve the use of this product in working environments
other than the above mentioned "Residential, commercial and light industry
environments".

For example, the following environments are not approved:

■ Industrial Environments (e.g. environments where a mains voltage of

380 V three-phase is used)

■ Medical Environments

■ Automotive Environments

■ Aircraft Environments

Any consequences resulting from the use of this product in working
environments that are not approved are not the responsibility of TOSHIBA.

The consequences of the use of this product in non-approved working
environments may be:

■ Interference with other devices or machines in the near surrounding

area.

■ Malfunction of, or data loss from, this product caused by disturbances

generated by other devices or machines in the near surrounding area.

Therefore TOSHIBA strongly recommend that the electromagnetic
compatibility of this product should be suitably tested in all non-approved
working environments before use. In the case of automobiles or aircraft, the
manufacturer or airline respectively should be asked for permission before
use of this product.

Furthermore, for general safety reasons, the use of this product in
environments with explosive atmospheres is not permitted.

A300/A300D

User’s Manual v

Modem warning notice

Conformity Statement

The equipment has been approved to [Council Decision 98/482/EC ­"TBR 21"] for pan-European single terminal connection to the Public
Switched Telephone Network (PSTN).

However, due to differences between the individual PSTNs provided in
different countries/regions the approval does not, of itself, give an
unconditional assurance of successful operation on every PSTN network
termination point.

In the event of problems, you should contact your equipment supplier in the
first instance.

Network Compatibility Statement

This product is designed to work with, and is compatible with the following
networks. It has been tested to and found to conform with the additional
requirements conditional in EG 201 121.

Germany ATAAB AN005, AN006, AN007, AN009, AN010 and

Greece ATAAB AN005, AN006 and GR01, 02, 03, 04
Portugal ATAAB AN001, 005, 006, 007, 011 and P03, 04, 08,

Spain ATAAB AN005, 007, 012, and ES01
Switzerland ATAAB AN002
All other

countries/regions

Specific switch settings or software setup are required for each network,
please refer to the relevant sections of the user guide for more details.

The hookflash (timed break register recall) function is subject to separate
national type approvals. It has not been tested for conformity to national
type regulations, and no guarantee of successful operation of that specific
function on specific national networks can be given.

A300/A300D

DE03, 04, 05, 08, 09,12,14,17

10

ATAAB AN003, 004

User’s Manual vi

Following information is only for EU-member states:

The symbol indicates that this product may not be treated as
household waste. Please ensure this product is properly
disposed as inappropriate waste handling of this product may
cause potential hazards to the environment and human health.
For more detailed information about recycling of this product,
please contact your local city office, your household waste
disposal service or the shop where you purchased the product.

This symbol may not stick depending on the country and region where you
purchased.

ENERGY STAR® Program

Your computer model may be ENERGY STAR® Compliant. If the model
you purchased is compliant, it is labeled with the ENERGY STAR® logo on

the computer and the following information applies.

A300/A300D

TOSHIBA is a partner in the Environmental Protection Agency’s (EPA)
ENERGY STAR
latest ENERGY STAR® guidelines for energy efficiency. Your computer

ships with the power management options preset to a configuration that will
provide the most stable operating environment and optimum system
performance for both AC power and battery modes.
To conserve energy, your computer is set to enter the low-power Sleep
mode which shuts down the system and display within 15 minutes of
inactivity in AC power mode. TOSHIBA recommends that you leave this
and other energy saving features active, so that your computer will operate
at its maximum energy efficiency. You can wake the computer from Sleep
mode by pressing the power button.

Products that earn the ENERGY STAR
emissions by meeting strict energy efficiency guidelines set by the US EPA
and the EU Commission. According to the EPA, a computer meeting the

new ENERGY STAR® specifications will use between 20% and 50% less
energy depending on how it is used.

Visit http://www.eu-energystar.org or http://www.energystar.gov for more
information regarding the ENERGY STAR Program.

®

Program and has designed this computer to meet the

®

prevent greenhouse gas

User’s Manual vii

GOST

Optical disc drive safety instructions

Be sure to check the international precautions at the end of this section.

Hitach-LG Data Storage

DVD Super Multi GSA-T40F/GSA-T40N

■ The DVD Super Multi drive employs a laser system. To ensure proper

use of this product, please read this instruction manual carefully and
retain for future reference. Should the unit ever require maintenance,
contact an authorized service location.

■ Use of controls, adjustments or the performance of procedures other

than those specified may result in hazardous radiation exposure.

■ To prevent direct exposure to the laser beam, do not try to open the

enclosure.

A300/A300D

User’s Manual viii

Panasonic

DVD Super Multi UJ-870B

■ The DVD Super Multi drive employs a laser system. To ensure proper

use of this product, please read this instruction manual carefully and
retain for future reference. Should the unit ever require maintenance,
contact an authorized service location.

■ Use of controls, adjustments or the performance of procedures other

than those specified may result in hazardous radiation exposure.

■ To prevent direct exposure to the laser beam, do not try to open the

enclosure.

A300/A300D

User’s Manual ix

Pioneer

DVD Super Multi DVR-KD08

■ The DVD Super Multi drive employs a laser system. To ensure proper

use of this product, please read this instruction manual carefully and
retain for future reference. Should the unit ever require maintenance,
contact an authorized service location.

■ Use of controls, adjustments or the performance of procedures other

than those specified may result in hazardous radiation exposure.

■ To prevent direct exposure to the laser beam, do not try to open the

enclosure.

A300/A300D

User’s Manual x

TOSHIBA SAMSUNG STORAGE TECHNOLOGY

CD-RW/DVD-ROM Drive TS-L462D

■ The CD-RW/DVD-ROM drive employs a laser system. To ensure

proper use of this product, please read this instruction manual carefully
and retain for future reference. Should the unit ever require
maintenance, contact an authorized service location.

■ Use of controls, adjustments or the performance of procedures other

than those specified may result in hazardous radiation exposure.

■ To prevent direct exposure to the laser beam, do not try to open the

enclosure.

A300/A300D

User’s Manual xi

TOSHIBA SAMSUNG STORAGE TECHNOLOGY

8x slim DVD Writable Drive TS-L632H

■ This DVD writable drive employ a laser system to ensure proper use of

this product, please read this instruction manual carefully and retainfor
future reference. Should the unit ever require maintenance, contact an
authorized service location-see service procedure.

■ Use of controls or adjustments or the performance of procedures other

than those specified herein may result in hazardous radiation
exposure.

■ To prevent direct exposure to laser beam, do not try to open the

enclosure.

A300/A300D

User’s Manual xii

TOSHIBA

HD DVD-ROM Drive SD-L802B

■ This HD DVD-rom drive employ a laser system to ensure proper use of

this product, please read this instruction manual carefully and retain for
future reference. Should the unit ever require maintenance, contact an
authorized service location-see service procedure.

■ Use of controls or adjustments or the performance of procedures other

than those specified herein may result in hazardous radiation
exposure.

■ To prevent direct exposure to laser beam, do not try to open the

enclosure.

A300/A300D

User’s Manual xiii

TOSHIBA

HD DVD-RW Drive SD-L912A

■ This dvd writable drive employ a laser system to ensure proper use of

this product, please read this instruction manual carefully and retain for
future reference. Should the unit ever require maintenance, contact an
authorized service location-see service procedure.

■ Use of controls or adjustments or the performance of procedures other

than those specified herein may result in hazardous radiation
exposure.

■ To prevent direct exposure to laser beam, do not try to open the

enclosure.

A300/A300D

User’s Manual xiv

International Precautions

A300/A300D

CAUTION: This appliance contains a laser
system and is classified as a "CLASS 1
LASER PRODUCT." To use this model
properly, read the instruction manual
carefully and keep this manual for your
future reference. In case of any trouble
with this model, please contact your
nearest "AUTHORIZED service station."
To prevent direct exposure to the laser
beam, do not try to open the enclosure.

VORSICHT: Dieses Gerät enthält ein
Laser-System und ist als
"LASERSCHUTZKLASSE 1 PRODUKT"
klassifiziert. Für den richtigen Gebrauch
dieses Modells lesen Sie bitte die
Bedienungsanleitung sorgfältig durch und
bewahren diese bitte als Referenz auf.
Falls Probleme mit diesem Modell
auftreten, benachrichtigen Sie bitte die
nächste "autorisierte Service-Vertretung".
Um einen direkten Kontakt mit dem
Laserstrahl zu vermeiden darf das Gerät
nicht geöffnet werden.

ADVARSEL: Denne mærking er anbragt
udvendigt på apparatet og indikerer, at
apparatet arbejder med laserstråler af
klasse 1, hviket betyder, at der anvendes
laserstrlier af svageste klasse, og at man
ikke på apparatets yderside kan bilve
udsat for utilladellg kraftig stråling.

APPARATET BOR KUN ÅBNES AF
FAGFOLK MED SÆRLIGT KENDSKAB
TIL APPARATER MED LASERSTRÅLER!

Indvendigt i apparatet er anbragt den her
gengivne advarselsmækning, som advarer
imod at foretage sådanne indgreb i
apparatet, at man kan komme til at udsatte
sig for laserstråling.

User’s Manual xv

A300/A300D

OBS! Apparaten innehåller
laserkomponent som avger laserstråining
överstigande gränsen för laserklass 1.

VAROITUS. Suojakoteloa si saa avata.
Laite sisältää laserdiodin, joka lähetää
näkymätöntä silmilie vaarallista
lasersäteilyä.

CAUTION: USE OF CONTROLS OR
ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE
SPECIFIED IN THE OWNER’S MANUAL
MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.

VORSICHT: DIE VERWENDUNG VON
ANDEREN STEURUNGEN ODER
EINSTELLUNGEN ODER DAS
DURCHFÜHREN VON ANDEREN
VORGÄNGEN ALS IN DER
BEDIENUNGSANLEITUNG
BESCHRIEBEN KÖNNEN
GEFÄHRLICHE
STRAHLENEXPOSITIONEN ZUR FOLGE
HABEN.

Important Notice

Copyrighted works including, but not limited to music, video, computer
program, databases are protected by copyright laws. Unless specifically
permitted under applicable copyright laws, you cannot copy, modify, assign,
transmit or otherwise dispose of any copyrighted work with the consent of
the owner of the copyright. Please take notice that unauthorized copying,
modification, assignment, transmission and disposition may be subject to
claims for damages and penalties.

■ Avoid using a telephone (other than a cordless type) during an electrical

storm. There may be a remote risk of electric shock from lightning.

■ Do not use the telephone to report a gas leak in the vicinity of the leak.

■ Use only the power cord indicated in this manual.

■ Replace only with the same or equivalent type battery recommended by

the manufacturer.

■ Dispose of used batteries according to the manufacturer's instructions.

Use only the battery pack that came with the computer or an optional
battery pack. Use of wrong battery could damage your computer.

TOSHIBA assumes no liability for any damage in such case.

User’s Manual xvi

General Precautions

TOSHIBA computers are designed to optimize safety, minimize strain and
withstand the rigors of portability. However, certain precautions should be
observed to further reduce the risk of personal injury or damage to the
computer.

Be certain to read the general precautions below and to note the cautions
included in the text of the manual.

Creating a computer-friendly environment

Place the computer on a flat surface that is large enough for the computer
and any other items you are using, such as a printer.

Leave enough space around the computer and other equipment to provide
adequate ventilation. Otherwise, they may overheat.

To keep your computer in prime operating condition, protect your work area
from:

■ Dust, moisture, and direct sunlight.

■ Equipment that generates a strong electromagnetic field, such as

stereo speakers (other than speakers that are connected to the
computer) or speakerphones.

■ Rapid changes in temperature or humidity and sources of temperature

change such as air conditioner vents or heaters.

■ Extreme heat, cold, or humidity.

■ Liquids and corrosive chemicals.

A300/A300D

Stress injury

Carefully read the Instruction Manual for Safety and Comfort. It contains
information on the prevention of stress injuries to your hands and wrists
that can be caused by extensive keyboard use. Chapter 3, Getting Started,
also includes information on work space design, posture and lighting that
can help reduce physical stress.

User’s Manual xvii

Heat injury

■ Avoid prolonged physical contact with the computer. If the computer is

used for long periods, its surface can become very warm. While the
temperature will not feel hot to the touch, if you maintain physical
contact with the computer for a long time, for example if you rest the
computer on your lap or if you keep your hands on the palm rest, your
skin might suffer a low-heat injury.

■ If the computer has been used for a long time, avoid direct contact with

the metal plate supporting the various interface ports as this can
become hot.

■ The surface of the AC adaptor can become hot when in use but this

condition does not indicate a malfunction. If you need to transport the
AC adaptor, you should disconnect it and let it cool before moving it.

■ Do not lay the AC adaptor on a material that is sensitive to heat as the

material could become damaged.

Pressure or impact damage

Do not apply heavy pressure to the computer or subject it to any form of
strong impact as this can damage the computer's components or otherwise
cause it to malfunction.

PC Card and ExpressCard overheating

Some PC Cards and ExpressCards can become hot during prolonged use
which may result in errors or instability in the operation of the device in
question. In addition, you should also be careful when you remove a
PC Card or ExpressCard that has been used for a long time.

A300/A300D

Mobile phones

Please be aware that the use of mobile phones can interfere with the audio
system. The operation of the computer will not be impaired in any way, but
it is recommended that a minimum distance of 30cm is maintained between
the computer and a mobile phone that is in use.

Instruction Manual for Safety and Comfort

All important information on the safe and proper use of this computer is
described in the enclosed Instruction Manual for Safety and Comfort. Be
sure to read it before using the computer.

User’s Manual xviii

Table of Contents

Chapter 1 Introduction

Equipment checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Special features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12

TOSHIBA Value Added Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13

Utilities and Applications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14

Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-17

Chapter 2 The Grand Tour

Front with the display closed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Left side. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Right side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Backside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

Underside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

Front with the display open. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

Optical Disc Drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8

AC adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12

Remote controller (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14

A300/A300D

Chapter 3 Getting Started

Installing the battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Connecting the AC adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

Opening the display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

Turning on the power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

Windows Vista™ setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

Turning off the power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

Restarting the computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8

System Recovery Options and Restoring

the pre-installed Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9

User’s Manual xix

A300/A300D

Chapter 4

Operating Basics

Using the TouchPad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Using the fingerprint sensor (optional) . . . . . . . . . . . . . . . . . . . . . . . 4-2

USB Sleep and Charge function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

Using the Web Camera (optional). . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10

Using the microphone (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11

Using the optical disc drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12

Writing CD/DVD with the DVD Super Multi drive

or HD DVD-ROM drive supporting DVD±R DL . . . . . . . . . . . . . . . . . 4-16

Writing CDs/DVDs/HD DVDs on HD DVD-RW drive. . . . . . . . . . . . . 4-20

TOSHIBA Disc Creator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-24

Data Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25

Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-26

Using Ulead DVD MovieFactory® for TOSHIBA. . . . . . . . . . . . . . . . 4-26

Media care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-28

Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-29

Using the FM tuner (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-32

Wireless communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-32

LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-35

Cleaning the computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-36

Moving the computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-36

Chapter 5 The Keyboard

Typewriter keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

F1 ... F12 function keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

Soft keys: Fn key combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

Hot keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3

Windows® special keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5

Keypad overlay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5

Generating ASCII characters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7

Chapter 6 Power and Power-Up Modes

Power conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

Power indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2

Battery types. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3

Care and use of the battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5

Replacing the battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10

Starting the computer by password . . . . . . . . . . . . . . . . . . . . . . . . . 6-12

Power-up modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12

Panel power off/on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13

System Auto Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13

Chapter 7 HW Setup

Accessing HW Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

HW Setup Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

User’s Manual xx

A300/A300D

Chapter 8

Optional Devices

ExpressCard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

SD/SDHC/MMC/MEMORY STICK/MEMORY STICK PRO/

xD Memory cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3

Memory expansion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6

Additional battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9

Additional AC adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9

External monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9

Television . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10

HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10

i.LINK (IEEE1394) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12

Security lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-14

Chapter 9 Troubleshooting

Problem solving process. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1

Hardware and system checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3

TOSHIBA support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-21

Appendix A Specifications

Appendix B Display Controller and Modes

Appendix C Wireless LAN

Appendix D AC Power Cord and Connectors

Appendix E Legal Footnotes

Appendix F If your computer is stolen

Glossary

Index

User’s Manual xxi

Preface

Congratulations on your purchase of the TOSHIBA A300/A300D computer.
This powerful notebook computer provides excellent expansion capability,
including multimedia devices, and it is designed to provide years of reliable,
high-performance computing.

This manual tells how to set up and begin using your computer. It also
provides detailed information on configuring your computer, basic
operations and care, using optional devices and troubleshooting.

If you are a new user of computers or if you’re new to portable computing,
first read over the Introduction and The Grand Tour chapters to familiarize
yourself with the computer's features, components and accessory devices.
Then read Getting Started for step-by-step instructions on setting up your
computer.

If you are an experienced computer user, please continue reading the
preface to learn how this manual is organized, then become acquainted
with this manual by browsing through its pages. Be sure to look over the

Specifications section of the Introduction, to learn about features that are

uncommon or unique to the computer. If you are going to install
ExpressCards or connect external devices such as a monitor, be sure to
read Chapter 8, Optional Devices.

A300/A300D

Manual contents

This manual is composed of the following nine chapters, six appendixes,
a glossary and an index.

Chapter 1, Introduction, is an overview of the computer's features,
capabilities, and options.

Chapter 2, The Grand Tour, identifies the components of the computer and
briefly explains how they function.

Chapter 3, Getting Started, provides a quick overview of how to begin
operating your computer and gives tips on safety and designing your work
area.

Chapter 4, Operating Basics, includes instructions on using the following
devices: TouchPad, Sound System, optical media drives, modem, wireless
communication and LAN. It also provides tips on care of the computer, and
CD/DVDs.

User’s Manual xxii

Chapter 5, The Keyboard, describes special keyboard functions including
the keypad overlay and hot keys.

Chapter 6, Power and Power-Up Modes, gives details on the computer's
power resources and battery save modes.

Chapter 7, HW Setup explains how to configure the computer using the
HW Setup program.

Chapter 8, Optional Devices, describes the optional hardware available.
Chapter 9, Troubleshooting, provides helpful information on how to perform

some diagnostic tests, and suggests courses of action if the computer
doesn’t seem to be working properly.

The Appendices provide technical information about your computer.
The Glossary defines general computer terminology and includes a list of

acronyms used in the text.
The Index quickly directs you to the information contained in this manual.

Conventions

This manual uses the following formats to describe, identify, and highlight
terms and operating procedures.

Abbreviations

On first appearance, and whenever necessary for clarity, abbreviations are
enclosed in parenthesis following their definition. For example: Read Only
Memory (ROM). Acronyms are also defined in the Glossary.

A300/A300D

Icons

Icons identify ports, dials, and other parts of your computer. The indicator
panel also uses icons to identify the components it is providing information
on.

Keys

The keyboard keys are used in the text to describe many computer
operations. A distinctive typeface identifies the key top symbols as they
appear on the keyboard. For example, Enter identifies the Enter key.

Key operation

Some operations require you to simultaneously use two or more keys. We
identify such operations by the key top symbols separated by a plus sign
(+). For example, Ctrl + C means you must hold down Ctrl and at the same
time press C. If three keys are used, hold down the first two and at the
same time press the third.

User’s Manual xxiii

A300/A300D

ABC When procedures require an action such as

clicking an icon or entering text, the icon’s name
or the text you are to type in is represented in the
type face you see to the left.

Display

ABC

Names of windows or icons or text generated by
the computer that appears on its display screen is
presented in the type face you see to the left.

Messages

Messages are used in this manual to bring important information to your
attention. Each type of message is identified as shown below.

Pay attention! A caution informs you that improper use of equipment or
failure to follow instructions may cause data loss or damage your
equipment.

Please read. A note is a hint or advice that helps you make best use of
your equipment.

Indicates a potentially hazardous situation, which could result in death or
serious injury, if you do not follow instructions.

Terminology

This term is defined in this document as follows:

Start The word "Start" refers to the button in

Microsoft

®

Windows Vista™.

User’s Manual xxiv

Introduction

This chapter provides an equipment checklist, and it identifies the
computer's features, options and accessories.

Some of the features described in this manual may not function properly if
you use an operating system that was not pre-installed by TOSHIBA.

Equipment checklist

Carefully unpack your computer. Save the box and packing materials for
future use.

Hardware

Check to make sure you have all the following items:

■ TOSHIBA A300/A300D Portable Personal Computer

■ Universal AC adaptor and power cord

Introduction

Chapter 1

Software

Microsoft® Windows Vista™

The following software is preinstalled:

■ Microsoft

■ Microsoft Internet Explorer

■ TOSHIBA Value Added Package

■ TOSHIBA Hardware Setup

■ TOSHIBA Supervisor Password

■ TOSHIBA Assist

■ TOSHIBA ConfigFree

■ TOSHIBA DVD PLAYER*

■ TOSHIBA HD DVD PLAYER*

■ TOSHIBA FingerPrint Utility*

■ TOSHIBA SD Memory Utilities

User’s Manual 1-1

®

Windows Vista™

Features

Introduction

■ TOSHIBA Disc Creator

■ TOSHIBA Face Recognition*

■ TOSHIBA Acoustic Silencer

■ Ulead MovieFactory

■ Presto! BizCard 5*

■ Online Manual*

* Indicates software that is preinstalled dependant on the model purchased.

®

for TOSHIBA*

Documentation

■ A300/A300D Portable Personal Computer User’s Manual

■ A300/A300D Quickstart

■ Instruction Manual for Safety and Comfort

■ Warranty information

If any of the items are missing or damaged, contact your dealer
immediately.

Please visit your region’s web site for the configuration details of the model
that you have purchased.

Processor

Built-in Depends on the model you purchased.

Please visit your region's website for the
configuration details of the model that you have
purchased.

Chipset Depends on the model you purchased.

Mobile Intel
Chipset

or
AMD M690G Chipset

®

PM965/GM965/GL960 Express

Memory

Slots PC2-5300 (PM965/GM965/RS690M)/PC2-4200

(GL960) 512 MB, 1024 MB or 2048 MB. Up to
2 GB memory module can be installed in the
memory slot for a maximum of 4 GB
(PM965/GM965/M690G), 2 GB (GL960) system
memory total, depending on the model you
purchased.

User’s Manual 1-2

Introduction

Main Memory
Disclaimer

Part of the main system memory may be used by
the graphics system for graphics performance
and therefore reduce the amount of main system
memory available for other computing activities.
The amount of main system memory allocated
to support graphics may vary depending on the
graphics system, applications utilized, system
memory size and other factors. For PC's
configured with 4 GB of system memory, the full
system memory space for computing activities will
be considerably less and will vary by model and
system configuration.

If your computer is configured with two 2 GB memory modules, the mem­ory might be displayed as approximately 3 GB only (depending on the
computer's hardware specifications). This is correct because the operating
system usually displays the available memory instead of the physical
memory (RAM) built into the computer. Various system components (like
the video adapter's GPU and PCI devices like Wireless LAN, etc.) require
their own memory space. Since a 32-bit operating system cannot address
more than 4 GB of memory these system resources overlap the physical
memory. It is a technical limitation that the overlapped memory is not avail­able to the operating system. Even though some tools might display the
actual physical memory built into your computer, the memory available to
the operating sys-tem will still be approximately 3 GB only.

User’s Manual 1-3

Video RAM Depending on the model you purchased.

Mobile Intel® GM965 Express Chipset/Mobile

®

Intel

GL960 Express Chipset model:

Video RAM capacity shares with main memory,
and the proportion depends on Dynamic Video
Memory Technology.

®

Mobile Intel

®

Intel

GM965 Express Chipset/Mobile

PM965 Express Chipset model in graphic

chip by ATI Mobility Radeon™ HD 3470:
External 64/128/256 MB.

®

Mobile Intel

®

Intel

GM965 Express Chipset/Mobile

PM965 Express Chipset model in graphic

chip by ATI Mobility Radeon™ HD 3650:
External 256/512 MB.
AMD M690G Chipset Chipset model:
Video RAM capacity shares with main memory,

and the proportion depends on ATI
HyperMemory™.

AMD M690G Chipset model in graphic chip by
ATI Mobility Radeon™ HD 3470:

External 64/128/256 MB.
AMD M690G Chipset model in graphic chip by

ATI Mobility Radeon™ HD 3650:
External 256/512 MB.

Introduction

Power

Battery Pack Your computer is powered by a rechargeable

lithium-ion battery pack.

RTC Battery The internal RTC battery backs up the Real Time

AC Adaptor The universal AC adaptor provides power to the

User’s Manual 1-4

Clock and calendar.

system and recharges the batteries when they
are low. It comes with a detachable power cord.

Because it is universal, it can receive a range of
AC voltage from 100 to 240 volts; however, the
output current varies among different models.
Using the wrong model can damage your
computer. Refer to the AC adaptor section in
Chapter 2, The Grand Tour.

Introduction

Disks

Hard disk Drive Depends on the model you purchased.

■ 120 GB

■ 160 GB

■ 200 GB

■ 250 GB

■ 320 GB

■ 400 GB

■ 500 GB

Other hard disk drives may be introduced in the
future.

Computers in this series are configured with an optical media drive.
The available optical media drives are described below.

User’s Manual 1-5

Introduction

DVD Super Multi drive
(Supporting DVD±R
DL)

Some models are equipped with a full-size DVD
Super Multi drive module that lets you record data
to rewritable CDs/DVDs as well as run either
12cm (4.72") or 8cm (3.15") CDs/DVDs without
using an adaptor. It reads DVD-ROMs at
maximum 8 speed and CD-ROMs at maximum
24 speed. It writes CD-Rs at up to 24 speed,
CD-RWs at up to 16 speed, DVD-Rs at maximum
8 speed, DVD-RWs at maximum 6 speed,
DVD+Rs at maximum 8 speed, DVD+RWs at
maximum 8 speed, DVD+R(DL) discs at
maximum 4 speed, DVD-R(DL) discs at maximun
4 speed, and DVD-RAMs at maximum 5 speed.

It supports the following formats:

■ DVD-ROM

■ DVD-Video

■ DVD-R

■ DVD-RW

■ DVD+R

■ DVD+RW

■ DVD-RAM

■ DVD+R DL

■ DVD-R DL

■ CD-DA

■ CD-Text

■ Photo CD (single/multi-session)

■ CD-ROM Mode 1, Mode 2

■ CD-ROMXA Mode 2 (Form1, Form2)

■ Enhanced CD (CD-EXTRA)

■ CD-G (Audio CD only)

■ Addressing Method 2

User’s Manual 1-6

Introduction

HD DVD-ROM Some models are equipped with a full-size

HD DVD-ROM drive module that lets you run
CDs/DVDs without using an adaptor. The drive
reads DVD-ROMs at maximum 8x speed and
CD-ROMs at maximum 24x speed, and HD DVDs
at maximum 1x speed and writes CD-Rs at up to
16x speed, CD-RWs at up to 10x speed, DVD-Rs
and DVD+Rs at up to 4x speed, DVDRWs and
DVD+RWs at up to 4x speed, DVD-R (Dual layer)
discs at up to 2x speed, DVD+R (Double Layer)
discs at up to 2.4x speed and DVD-RAMs at up to
3x speed. It supports the following formats:

■ CD-R

■ CD-RW

■ DVD-ROM

■ DVD-Video

■ CD-DA

■ CD-Text

■ Photo CD (single/multi-session)

■ CD-ROM Mode 1, Mode 2

■ CD-ROM XA Mode 2 (Form1, Form2)

■ Enhanced CD (CD-EXTRA)

■ Addressing Method 2

■ DVD-R

■ DVD-R (Dual Layer)

■ DVD-RW

■ DVD+R

■ DVD+R (Double Layer)

■ DVD+RW

■ DVD-RAM

■ HD DVD-ROM

User’s Manual 1-7

Introduction

HD DVD-RW drive Some models are equipped with a full-size

HD DVD-RW drive module that lets you run
CDs/DVDs without using an adaptor. The drive
reads DVD-ROMs at maximum 8x speed,
CD-ROMs at maximum 24x speed, and HD DVDs
at maximum 1x speed and writes CD-Rs at up to
16x speed, CD-RWs at up to 4x speed, DVD-Rs
and DVD+Rs at up to 4x speed, DVD-RWs and
DVD+RWs at up to 4x speed, DVD-R (Dual layer)
discs at up to 2x speed, DVD+R (Double Layer)
discs at up to 2.4x speed, DVD-RAMs at up to 3x
speed, HD DVD-Rs and HD DVD-RWs at up to 1x
speed. It supports the following formats:

■ CD-R

■ CD-RW

■ DVD-ROM

■ DVD-Video

■ CD-DA

■ CD-Text

■ CD-DA

■ CD-Text

■ Photo CD (single/multi-session)

■ CD-ROM Mode 1, Mode 2

■ CD-ROM Mode 1, Mode 2

■ CD-ROM XA Mode 2 (Form1, Form2)

■ Enhanced CD (CD-EXTRA)

■ Addressing Method 2

■ DVD-R

■ DVD-R (Dual Layer)

■ DVD-RW

■ DVD+R

■ DVD+R (Double Layer)

■ DVD+RW

■ DVD-RAM

■ HD DVD-ROM

■ HD DVD-R

■ HD DVD-RW

User’s Manual 1-8

Introduction

Display

The computer's LCD panel supports high-resolution video graphics. The
screen can be set at a wide range of viewing angles for maximum comfort
and readability.

Built-In 15.4" WXGA 16 M colors, with the following

resolution: 1280 horizontal × 800 vertical pixels

Graphics Controller Graphics controller maximizes display

performance. Refer to Appendix B, Display

Controller and Modes for more information.

Keyboard

Built-In TOSHIBA Vista keyboard, 86 keys or 87 keys,

compatible with IBM enhanced keyboard,
embedded numeric overlay, dedicated cursor
control, and keys. Refer to Chapter 5,

The Keyboard,for details.

Pointing Device

Built-In TouchPad A TouchPad and control buttons in the palm rest

enable control of the on-screen pointer and
scrolling of windows.

Ports

External Monitor This 15-pin port lets you connect an external

HDMI This HDMI jack allows you to connect external

Universal Serial Bus
(USB 2.0)

i.LINK (IEEE1394a) This port enables high-speed data transfer

TV Out The 4-pin S-Video port is compatible with PAL or

Infrared receiver
window

User’s Manual 1-9

video display.

display/audio devices. (Provided with some
models.)

The computer has Universal Serial Bus ports that
comply with the USB 2.0 standard, which enables
data transfer speeds 40 times faster than the
USB 1.1 standard. (The ports also support
USB 1.1.)

directly from external devices such as digital
video cameras.

NTSC TV standard, supporting Macrovision 7.02
copy protection.

This window receives signals from the remote
control. (Provided with some models.)

Slots

Introduction

ExpressCard The ExpressCard expansion slot can

Multiple Digital Media
Card Slot

accommodate two standard module formats; an
ExpressCard/34 module and an ExpressCard/54
module. An ExpressCard module is a small add­in card technology based on the PCI Express and
Universal Serial Bus (USB) interfaces.

Supports SD/SDHC memory card, MMC,
MEMORY STICK, MEMORY STICK PRO and
xD Picture card.

Multimedia

Web Camera Allows you to record/send still or video images

with this integrated webcam.
(Provided with some models.)

Sound System The Windows

as well as jacks for an external microphone and
headphones.

Headphone(S/P DIF)
jack

Microphone Jack A 3.5 mm mini microphone jack enables

This jack outputs analog audio signals. This jack
can be used also as S/P DIF jack and enables
connection of optical digital correspondence
apparatus.

connection of a three-conductor mini jack for
monaural microphone input.

®

Sound System provides speakers

Communications

Modem Provides capability for data and fax

communication. It supports V.90 (V.92). The
speed of data transfer and fax communication
depends on the analog telephone line conditions.
The computer has a modem jack for connection
to a telephone line. Both V.90 and V.92 are
supported only in the USA, Canada, UK, France
and Germany. V.90 is available in other regions.

LAN The computer is equipped with a LAN card that

supports Fast Ethernet LAN (100 MBit/s,
100BASE-TX) or Gigabit Ethernet LAN (1 GBit/s,
1000BASE-T).

User’s Manual 1-10

Introduction

Wireless LAN Where present, it supports the A,B,G and draft N

standards but it is compatible with other LAN
systems based on Direct Sequence Spread
Spectrum/Orthogonal Frequency Division
Multiplexing radio technology that complies with
the IEEE 802.11 Standard.

■ Automatic Transmit Rate Select mechanism in

the transmit range of 54, 48, 36, 24, 18, 12, 9
and 6 MBit/s. (IEEE 802.11a/g)

■ Automatic Transmit Rate Select mechanism in

the transmit range of 11, 5.5, 2 and 1 MBit/s.
(IEEE 802.11b)

■ Roaming over multiple channels

■ Card Power Management

■ Wired Equivalent Privacy (WEP) data

encryption, based on 128 bit encryption
algorithm.

■ Advanced Encryption Standard (AES) data

encryption, based on 128 bit encryption
algorithm.

Bluetooth Some computers in this series are equipped with

Bluetooth functions. Bluetooth wireless
technology eliminates the need for cables
between electronic devices such as computers
and printers. Bluetooth provides fast, reliable, and
secure wireless communication in a small space.
(Provided with some models)

Wireless
Communication
Switch

This switch turns the Wireless LAN and Bluetooth
functions on and off.

(Provided with some models)

Security

Security lock slot Connects an optional security lock to anchor the

computer to a desk or other large object.

Password Power-on password protection

HDD password protection
Two level password architecture
Fingerprint authentication (provided with some

models)

User’s Manual 1-11

Special features

The following features are either unique to TOSHIBA computers or are
advanced features, which make the computer more convenient to use.

Hot Keys Key combinations let you quickly modify the

Keypad Overlay A ten-key pad is integrated into the keyboard.

Instant Security The hot key function Fn + F1 blanks the screen

Display Automatic
Power Off

HDD Automatic Power

*1

Off

System Automatic
Sleep
Mode/Hibernation

Intelligent Power

*1

Supply

Battery Save Mode

Panel Power On/Off

Introduction

system configuration directly from the keyboard
without running a system configuration program.

Refer to the Keypad overlay section in Chapter 5,
The Keyboard,for instructions on using the
keypad overlay.

and disables the computer, providing data
security.

*1

This feature automatically cuts off power to the
internal display when there is no keyboard input
for a specified time. Power is restored when any
key is pressed.

This can be specified in the Power Options.
This feature automatically cuts off power to the

hard disc drive when it is not accessed for a
specified time. Power is restored when the hard
disc is accessed.

This can be specified in the Power Options.
This feature automatically shuts down the system

into Sleep Mode or Hibernation Mode when there

*1

is no input or hardware access for a specified
time.

This can be specified in the Power Options.
A microprocessor in the computer's intelligent

power supply detects the battery’s charge and
calculates the remaining battery capacity. It also
protects electronic components from abnormal
conditions, such as voltage overload from an
AC adaptor.

This can be specified in the Power Options.

*1

This feature lets you save battery power.
This can be specified in the Power Options.

*1

This feature turns power to the computer off when
the display panel is closed and turns it back on
when the panel is opened.

This can be specified in the Power Options.

User’s Manual 1-12

Introduction

Low Battery
Automatic
Hibernation

Hibernation This feature lets you turn off the power without

Sleep Mode If you have to interrupt your work, you can turn off

*1 Click , Control Panel, System and Maintenance, and then click

Power Options.

*1

When battery power is exhausted to the point that
computer operation cannot be continued, the
system automatically enters Hibernation Mode
and shuts down.

This can be specified in the Power Options.

exiting from your software. The contents of main
memory are saved to the hard disk so that when
you turn on the power again, you can continue
working right where you left off. Refer to the

Turning off the power section in Chapter 3,
Getting Started,for details.

the power without exiting from your software.
Data is maintained in the computer's main
memory so that when you turn on the power
again, you can continue working right where you
left off.

TOSHIBA Value Added Package

This section describes the TOSHIBA Component features pre-installed on
the computer.

TOSHIBA Power
Saver

TOSHIBA Zooming
Utility

TOSHIBA PC
Diagnostic Tool

TOSHIBA Flash Cards This utility supports the following functions.

TOSHIBA
Components
Common Driver

User’s Manual 1-13

TOSHIBA Power Saver provides you with the
features of more various power supply
managements.

This utility allows you to enlarge or reduce the
icon size on the Windows Desktop, or the zoom
factor associated with specific supported
applications.

The TOSHIBA PC Diagnostic Tool will display
basic system configuration information and allow
the functionality of some of the computer's built-in
hardware devices to be tested.

■ Hot key function

■ TOSHIBA utility launcher function

TOSHIBA Components Common Driver contains
the module required for the utility which TOSHIBA
offers.

Introduction

TOSHIBA
Accessibility

TOSHIBA Button
Support

Utilities and Applications

This section describes pre-installed utilities and tells how to start them.
For details on operations, refer to each utility’s online manual, help files
or readme.txt files.

TOSHIBA Assist TOSHIBA Assist is a graphical user interface that

HW Setup This program lets you customize your hardware

Power On Password Two levels of password security, supervisor and

TOSHIBA Disc
Creator

The TOSHIBA Accessibility utility provides
support to movement impaired users when they
need to use the TOSHIBA Hot-key functions. In
"sticky", that is you can press it once, release it,
and then press one of the "F" keys in order to
access its specific function. When set, the Fn key
will remain active until another key is pressed.

This utility controls the button operation of the
computer.

The starting application from the button can be
changed.

provides easy access to help and services.

settings according to the way you work with your
computer and the peripherals you use. To start
the utility, double click the TOSHIBA Assist on
your desktop, select OPTIMIZE tab, and click
TOSHIBA Hardware Settings.

user, are available to prevent unauthorized
access to your computer.

To register a supervisor password, double click
the TOSHIBA Assist on your desktop select the
SECURE tab and start the Supervisor password
utility.

To set a user password, select the SECURE tab
on TOSHIBA Assist, then start the User
password utility. On the Password tab you can
register a user password.

You can create discs in several formats including
audio CDs that can be played on a standard
stereo CD player and data discs to store the files
and folders on your hard disk drive. This software
can be used on a model with a CD-RW/DVD­ROM drive, DVD Super Multi drive, HD DVD
drive.

User’s Manual 1-14

Introduction

TOSHIBA DVD-RAM
Utility

TOSHIBA DVD-RAM Utility has a Physical
Format function and Write-Protect function to
DVD-RAM.

This utility is contained in the TOSHIBA Disc
Creator setup module.

To run the TOSHIBA DVD-RAM Utility, click ,
select All Programs, TOSHIBA, CD&DVD

Applications, and then click DVD-RAM Utility.

CD/DVD Drive
Acoustic Silencer

This utility allows you to configure the read speed
of the CD drive. You can either configure Normal
Mode, which operates the drive at its maximum
speed for quick data access, or Quiet Mode,
whcih runs at single speed for CD audio and
which can lessen operational noise. It is
ineffective in DVD mode.

Ulead DVD
MovieFactory
TOSHIBA

®

for

You can edit digital video and make a DVD-Video
and support Label Flash function.

(Provided with some models.)

The availability of Label Flash function depends on the model you
purchased.

FingerPrint utility Depending on the model purchased, your

computer has a fingerprint utility installed for the
purpose of enrolling and recognizing fingerprints.
By enrolling the ID and password to the fingerprint
authentication device, it is no longer necessary to
input the password from the keyboard. Just by
swiping the finger against the fingerprint sensor,
the following functions will be enabled:

■ Log-on to Windows and access a security

enabled homepage through IE (Internet
Explorer).

■ Files and folders can be encrypted/decrypted

and third party access to them prevented.

■ Disable the password-protected screensaver

when returning from power-saving (Sleep)
mode.

■ System boot authentication and Single Touch

Boot feature.

■ Power on Security and Single Sign On

feature.

TOSHIBA DVD Player The DVD Player is used to play DVD Videos.

It has an on-screen interface and functions.

User’s Manual 1-15

Introduction

TOSHIBA HD DVD
Player

The HD DVD Player is used to play HD DVD
Videos. It has an on-screen interface and
functions. (Provided with some models.)

TOSHIBA ConfigFree ConfigFree is a suite of utilities to allow easy

control of communication devices and network
connections. ConfigFree also allows you to find
communication problems and create profiles for
easy switching between location and
communication networks.

To run ConfigFree, click , select All Programs,

TOSHIBA, Networking and then click
ConfigFree.

TOSHIBA Face
Recognition

TOSHIBA Face Recognition uses a face
verification library to verify the face data of users
when they log in to Windows. If the verification is
successful, the user will be logged into Windows
automatically. The user can thus avoid having to
enter a password or the like, which makes the
login process easier. (Provided with some
models.)

Presto! BizCard 5 Presto! BizCard keeps track of names,

companies, mailing addresses, phone/fax
numbers, e-mail addresses, and more. Simply
scan your business cards and Presto! BizCard
automatically saves the data and image for each
card. Different viewing modes are available for
easy searching, editing, creating, and sorting. You
can share information with desktop organizers,
contact managers, personal information
managers (PIMs), and personal digital assistants
(PDAs). You can also print ID badges, mailing
labels, and stickers. (Provided with some
models.)

User’s Manual 1-16

Introduction

Options

Windows Mobility
Center

You can add a number of options to make your computer even more
powerful and convenient to use. Refer to Chapter 8 Optional Devices, for
details. The following options are available:

Memory expansion Two memory modules can be installed in this

Use only PC5300* compatible DDRII memory modules. See your
TOSHIBA dealer for details.

* The availability of DDRII depends on the model you purchased.

This section describes the Windows Mobility
Center. Mobility Center is a utility for accessing
several mobile PC settings quickly in one window.
A maximum of eight tiles are prepared as the
operating system default. Two additional tiles are
also added to your Mobility Center.

Installing the "TOSHIBA Extended Tiles for
Windows Mobility Center" package will add the
following functions.

■ Lock Computer:

Lock your computer without turning it off. This
has the same function as the Lock button at
the bottom of the right pane of the start menu.

■ TOSHIBA Assist:

Open the TOSHIBA Assist if it is already
installed in your computer.

computer.

Battery pack An additional battery pack can be purchased from

your TOSHIBA dealer. Use it as a spare to
increase your computer’s operating time.

AC Adaptor If you use your computer at more than one site

User’s Manual 1-17

frequently, it may be convenient to purchase an
additional AC adaptor for each site so you will not
have to carry the adaptor with you.

The Grand Tour

This chapter identifies the various components of your computer. Become
familiar with each component before you operate the computer.

Front with the display closed

The following figure shows the computer's front with its display panel in the
closed position.

DC in

Wireless

Communication

Switch

off

LED

on

Power

LED

Battery

LED

The Grand Tour

Chapter 2

Disk
LED

Multiple Digital

Media Card Slot LED

Wireless

Activity

LED

Receiver

Wireless
Communication

Infrared

Window

Front of the computer with display closed

Multiple

Digital Media

Card Slot

Microphone

Jack

The Wireless Communication Switch turns the
wireless networking transceiver on or off.

Headphone

(S/P DIF)

jack

Volume

Dial

Switch

Set the switch to off in airplanes and hospitals. Check the wireless activity
indicator. It will stop glowing when the wireless communication function is
off.

DC IN LED The DC IN LED indicates the computer is

connected to the AC adaptor and it is plugged into
an AC power source.

User’s Manual 2-1

The Grand Tour

Power LED The Power indicator glows blue when the

computer is on. If you select Sleep Mode from
Turn Off Computer, this indicator flashes orange
(one second on, two seconds off) while the
computer enters Sleep Mode.

Battery LED The Battery indicator shows the condition of the

battery's charge: Blue indicates a full charge,
orange indicates that the battery is charging and
flashing orange indicates a low battery charge.
Refer to Chapter 6, Power and Power-Up Modes.

Disk LED Disk LED indicates that the hard disk drive or

optical disc drive is being accessed.

Multiple Digital Media
Card Slot LED

Multiple Digital Media Card Slot LED lights up
when the Multiple Digital Media Card Slot is
accessed.

(Provided with some models)

Wireless Activity LED Indicates whether Wireless LAN or Bluetooth is

active or not.
(Provided with some models)

Infrared Receiver
Window

An infrared receiver window is provided with
some models. This is a sensor window that
receives signals from the remote control which is
provided with some models.

Multiple Digital Media
Card Slot

Supports SD/SDHC memory card, MMC,
MEMORY STICK, MEMORY STICK PRO and
xD Picture card.

Microphone Jack A 3.5 mm mini microphone jack enables

connection of a three-conductor mini jack for
monaural microphone input.

Headphone (S/P DIF)
jack

This jack outputs analog audio signals. This jack
can be used also as S/P DIF jack and enables
connection of optical digital correspondence
apparatus.

Volu m e D i a l Use this dial to adjust the volume of the stereo

speakers or headphones.

User’s Manual 2-2

Left side

The Grand Tour

The following figure shows the computer's left side.

Port

Cooling VentsExternal Monitor

TV Out

Port

The left side of the computer

Universal Serial

Bus (USB 2.0) ports

LAN

HDMI

Jack

port

ExpressCard

Slot

i.LINK

(IEEE 1394a)

Port

External Monitor Port This 15-pin port lets you connect an external

video display.

Cooling Vents Cooling vents help prevent the CPU from

overheating.

Do not block the cooling vents. Also ensure that foreign objects are kept
out of the vents as items such as pins or similar objects can damage the
computer's circuitry.

Universal Serial Bus
(USB 2.0)

Universal Serial Bus ports, which comply to the
USB 2.0 standard, are provided. The port with the
icon ( ) has USB Sleep and Charge function.

ExpressCard Slot This slot allows you to insert an ExpressCard. An

ExpressCard is a small, modular add-in card
technology based on PCI Express and the
Universal Serial Bus (USB) interface. The max.
transmission rate is 2.5 GBps. ExpressCard/34
and ExpressCard/54 types are supported.

TV Out Port Connect a 4-pin S- video cable into this connector

in order to output either an NTSC or PAL
television signal.

HDMI port This port allows you to connect digitally to an

HDTV or home theater receiver.

LAN Jack This jack lets you connect to a LAN. The adaptor

has built-in support for Fast Ethernet LAN or Giga
bit Ethernet. (Dependent on the model you
purchased.) Refer to Chapter 4, Operating

Basics,for details.

User’s Manual 2-3

The Grand Tour

Right side

i.LINK (IEEE1394a)
Port

This port allows you to connect an external
device, such as a digital video camera, for
highspeed data transfer.

(Provided with some models)

The following figure shows the computer's right side.

Eject

Button

Emergency

Eject Hole

Security

DC in 19V

Jack

Lock

USB

Ports

Modem

Jack or FM

Antenna

Jack*

ODD

Indicator

The right side of the computer

* The figure shows Modem Jack.

ODD Indicator The ODD indicator glows amber when the

computer accesses the optical disc drive.

Eject Button Press this button to open the ODD tray.
Security Lock A security cable attaches to this port. The optional

security cable anchors your computer to a desk or
other large object to deter theft.

Universal Serial Bus
(USB 2.0) ports

Universal Serial Bus ports, which comply to the
USB 2.0 standard, are provided. The port with the
icon ( ) has USB Sleep and Charge function.

Modem Jack The modem jack allows you to use a modular

cable to connect the modem directly to a
telephone line. (Dependent on the model you
purchased.)

■ In case of a lightning storm, unplug the

modem cable from the telephone jack.

■ Do not connect the modem to a digital

telephone line. A digital line will damage the
modem.

FM Antenna Jack A jack enables the connection of FM antenna.

(Depends on the model you purchased.)

User’s Manual 2-4

The Grand Tour

Backside

The following figure shows the computer's back panel.

Underside

The following figure shows the underside of the computer. Make sure the
display is closed before turning over your computer.

Emergency Eject Hole In the event that the disc drive becomes

inexplicably locked or stops responding press this
button to force a manual ejection of the ODD tray.

DC IN 19V Jack The AC adaptor connects to this socket. Use only

the model of AC adaptor that comes with the
computer. Using the wrong adaptor can damage
your computer.

The backside of the computer

Cooling

Vents

Memory Module

and Wireless

LAN Cover

Hard Disk

Cover

Battery
Release
Latch

Battery Pack

Lock

The underside of the computer

User’s Manual 2-5

Battery Pack

The Grand Tour

Cooling Vents Cooling vents help prevent the CPU from

Memory Module and
Wireless LAN Cover

Hard Disk Cover This cover protects the hard disk.
Battery Pack Lock Slide this lock to prepare the battery pack for

Battery Pack The battery pack powers the computer when the

Battery Release Latch Slide and hold this latch to release the battery

Front with the display open

This section shows the front of the computer with the display open. Refer to
the appropriate illustration for details. To open the display, lift the front of the
display. Position the display at a comfortable viewing angle.

Web Camera

LED*

overheating.
This cover protects the two memory module

sockets — one or two modules are pre-installed.
Refer to the Memory expansion section in
Chapter 8, Optional Devices.

removal.

AC adaptor is not connected. For detailed
information on the battery pack, refer to
Chapter 6, Power and Power-Up Modes.

pack for removal. For detailed information on
removing the battery pack, refer to Chapter 6,

Power and Power-Up Modes.

Web

Camera*

Built-in

microphone*

Power Button

Mute Button or LED On/Off Button*

CD/DVD Button*

Display

Screen

Speaker

The front of the computer with the display open

Play/Pause Button*

Stop Button*

Previous Button*

Fingerprint

Sensor*

TouchPad

Control Buttons

Next Button*

Speaker

TouchPad

* Provided with some models

User’s Manual 2-6

The Grand Tour

Please handle your computer carefully to avoid scratching or damaging the
surface.

Speakers The speakers emit sound generated by your

software as well as audio alarms, such as low
battery condition, generated by the system.

Display Screen The LCD displays high-contrast text and graphics.

Refer to Appendix B, Display Controller and

Modes. When the computer operates on the

AC adaptor the display screen’s image will be
somewhat brighter than when it operates on
battery power. The lower brightness level is
intended to save battery power.

Web Camera LED Web Camera LED indicates that the web camera

is working or not. (Provided with some models)

Web Camera Allows you to take a picture or send an image to

web contacts.
(Provided with some models)

Built-in microphone The microphone is used with the Web Camera to

talk to other Web Camera users and to record
messages on windows media.

Power Button Turns the computer on and off and puts it into

Hibernation mode and wakes it up from Sleep
mode.

Mute Button or LED
On/Off Button

Depending on the model you purchased, press
this button to mute the volume or to switch the
illumination of the TouchPad, brand logo and
buttons on or off.

CD/DVD Button Pressing this button will launch an application

program that allows playing of CDs or DVDs. The
application that is launched differs by model:
Windows Media Player/TOSHIBA DVD
PLAYER/TOSHIBA HD DVD PLAYER.

(Provided with some models)

Play/Pause Button Press this button to begin playing an audio CD, a

DVD movie or digital audio file. This button also
acts as a Pause button.

(Provided with some models)

Stop Button Stops playing of the CD, DVD or digital audio.

(Provided with some models)

Previous Button Skips backwards to the previous track, chapter or

digital file. Refer to Chapter 4, Operating Basics,
for details.

(Provided with some models)

User’s Manual 2-7

The Grand Tour

Next Button Skips forward to the next track, chapter or digital

TouchPad A TouchPad located in the centre of the palm rest

Fingerprint Sensor Just by swiping the finger against the fingerprint

TouchPad Control
Buttons

file. Refer to Chapter 4, Operating Basics, for
details.

(Provided with some models)

is used to control the on-screen pointer.

sensor, the following functions will be enabled:
Log-on to Windows and access a security­enabled homepage through IE (Internet Explorer)
Files and folders can be encrypted/decrypted and
third party access to them prevented. Disable the
password-protected screensaver when returning
from power-saving (Sleep) mode. System boot
authentication and Single Touch Boot feature.
Authentication of the User Password and Hard
Disk Drive Password when booting up the
computer. Refer to the Using the fingerprint

sensor (optional) section in Chapter 4, Operating
Basics.

(Provided with some models)
These let you select menu items or manipulate

text and graphics designated by the on-screen
pointer. Refer to the Using the TouchPad section
in Chapter 4, Operating Basics.

Optical Disc Drive

An ATAPI interface controller is used for optical disc operation. When the
computer is accessing a optical disc, an indicator on the drive glows.

Region codes for DVD drive and media

Optical disc drive and their associated media are manufactured according
to the specifications of six marketing regions. When you purchase DVD­Video, make sure it matches your drive, otherwise it will not play properly.

Code Region
1 Canada, United States
2 Japan, Europe, South Africa, Middle East
3 Southeast Asia, East Asia
4 Australia, New Zealand, Pacific Islands, Central America,

South America, Caribbean

5 Russia, Indian Subcontinent, Africa, North Korea, Mongolia
6 China

User’s Manual 2-8

About HD DVD

This section describes the features and use of HD DVD and HD DVD
Media.

Summary

HD DVD allows users to enjoy video, concerts and other packaged content
by taking advantage of its large amount of storage space and high-quality
audio and video. HD DVD also allows for the storage of long video when
combined with the latest video compression technologies.

The storage capacity and data transfer rate of HD DVD is superior to
standard DVD, with two types of playback-only discs in single-sided
singlelayer 15 GB and single-sided dual-layer 30 GB (Gigabyte) formats.

■ Unfinalized DVDs created on home DVD recorders may not be

playable on the computer.

■ When inserting an unfinalized DVD-R DL disc into the computer,

Windows Vista may automatically finalize the disc and prevent further
writing.

Notes on use

■ Because HD DVD is a new format there is a possibility of new features

being added at a later date. As such, it is important that the purchaser
understands that software and other updates may be necessary after
purchase. Please be sure to complete user registration in order to
receive timely product updates.

■ This product can play existing DVD and CD formats, however, playback

may not be possible with some software. This product cannot play
Blu-ray DISC™ format software.

■ HD DVD is a new standard which makes use of new technologies. As

such, there is a possibility of problems occurring related to connection,
compatibility or operation with some discs and other digital devices. The
HD DVD-ROM logo signifies that this drive complies with the HD DVD
physical standard, and does not signify compliance with the HD DVD
Video standard. This device does not support advanced features of the
HD DVD Video standard as defined by the DVD Forum, including
picture-in-picture and network dowload features. Screen movement
may not be smooth, and performance may be lowered with some
HD DVD content.

■ Playback of high bit rate content may cause frame dropping, audio

skipping or decrease in computer performance.

■ Viewing of HD DVD content on an external display requires a HDCP

capable HDMI™ or DVI input on the external display.

■ Make sure to connect the computer's AC adaptor when playing a

HD DVD.

■ CPU power is concentrated on HD DVD playback when playing a

HD DVD, so make sure to exit all other applications.

The Grand Tour

User’s Manual 2-9

The Grand Tour

■ Dolby Digital audio enhancements are only supported by Microsoft®

Windows
or more are downsampled when output through either the built-in
speakers or headphone jack.

■ This device supports AACS (Advanced Access Content System) next

generation copy protection technology. Renewal of the AACS key
integrated into this device is required for uninterrupted enjoyment of
HD DVD. An Internet connection is required when renewing the key.

■ For more information on AACS keys, visit the AACS website

(http://www.aacsla.com/home).

®

operating systems. Content with high sample rates of 48kHz

Writable discs

This section describes the types of writable CD discs. Check the
specifications of your drive for the type of discs it can write. Refer to
Chapter 4, Operating Basics.

CDs

■ CD-R discs can be written only once. The recorded data cannot be

erased or changed.

■ CD-RW discs can be recorded more than once. Use either 1, 2, or 4

multi speed CD-RW discs or high-speed 4- to 10-speed discs. The write
speed of the ultra-speed CD-RW discs (Ultra-speed is available on the
DVD-ROM & CD-R/RW drive only) is a maximum of 24-speed.

DVDs

■ DVD-R, DVD+R, DVD-R DL and DVD+R DL discs can be written only

once. The recorded data cannot be erased or changed.

■ DVD-RW, DVD+RW and DVD-RAM discs can be recorded more than

once.

HD DVDs (supported by HD DVD-RW drive only)

■ HD DVD-R discs can be written only once. The recorded data cannot

be erased or changed.

■ HD DVD-RW discs can be recorded more than once.

DVD Super Multi drive (Supporting DVD±R DL)

The full-size DVD Super Multi drive module lets you record data to writable
CD/DVDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs
without using an adaptor.

User’s Manual 2-10

The read speed is slower at the centre of a disc and faster at the outer
edge.

DVD read 8 speed (maximum)
DVD-R write 8 speed (maximum)
DVD-RW write 6 speed (maximum)
DVD+R write 8 speed (maximum)
DVD+RW write 8 speed (maximum)
DVD-R(DL) write 4 speed (maximum)
DVD+R(DL) write 4 speed (maximum)
DVD-RAM write 5 speed (maximum)
CD read 24 speed (maximum)
CD-R write 24 speed (maximum)
CD-RW write 16 speed (maximum, ultra-speed media)

HD DVD-ROM drive

The full-size HD DVD-ROM drive module lets you run either 12 cm (4.72")
HD DVDs,12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an
adaptor.

The read speed is slower at the center of a disc and faster at the outer
edge.

CD read 24 speed (maximum)
DVD read 8 speed (maximum)
HD DVD read 1 speed (maximum)
DVD-R write 4 speed (maximum)
DVD-R DL write 2 speed (maximum)
DVD-RW write 4 speed (maximum)
DVD+R write 4 speed (maximum)
DVD+R DL write 2.4 speed (maximum)
DVD+RW write 4 speed (maximum)
DVD-RAM write 3 speed (maximum)
CD-R write 16 speed (maximum)
CD-RW write 10 speed (maximum, ultra-speed media)

The Grand Tour

User’s Manual 2-11

HD DVD-RW drive

The full-size HD DVD-RW drive module lets you run either 12 cm (4.72")
HD DVDs,12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an
adaptor.

The read speed is slower at the center of a disc and faster at the outer
edge.

CD read 24 speed (maximum)
DVD read 8 speed (maximum)
HD DVD read 1 speed (maximum)
HD DVD-R write 1 speed (maximum)
HD DVD-R DL write 1 speed (maximum)
HD DVD-RW write 1 speed (maximum)
DVD-R write 4 speed (maximum)
DVD-RW write 4 speed (maximum)
DVD+R write 4 speed (maximum)
DVD+RW write 4 speed (maximum)
DVD+R DL write 2.4 speed (maximum)
DVD-R DL write 2 speed (maximum)
DVD-RAM write 3 speed (maximum)
CD-R write 16 speed (maximum)
CD-RW write 10 speed (maximum, ultra-speed media)

The Grand Tour

AC adaptor

The AC adaptor converts AC power to DC power and reduces the voltage
supplied to the computer. It can automatically adjust to any voltage from
100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to
use the computer in almost any country/region.

To recharge the battery, simply connect the AC adaptor to a power source
and the computer. Refer to Chapter 6, Power and Power-Up Modes, for
details.

User’s Manual 2-12

The AC adaptor

The Grand Tour

■ Use only the AC adaptor that came with the computer or an equivalent

optional adaptor. Use of the wrong adaptor could damage your
computer. TOSHIBA assumes no liability for any damage in such case.

■ Use only the AC Adaptor supplied with your computer or an equivalent

adaptor that is compatible. Use of any incompatible adaptor or other
types of AC Adaptors may have a different voltage which could cause
damage to your computer, computer failure and/or possible data loss.
TOSHIBA assumes no liability for any damage, computer failure and/or
data loss caused by use of an incompatible adaptor.

Use only the AC adaptor supplied as an accessory. Other AC adaptors
have different voltage and terminal polarities and use of them may produce
heat and smoke or even result in fire or rupture.

User’s Manual 2-13

Remote controller (optional)

A remote controller, which is provided with some models, enables you to
perform some functions of your computer from a distant location.

You can use your remote controller with Media Center to play CDs, DVDs
and videos, to view pictures.

The remote controller helps you to control the playback of a movie through
Media Center.

Using the remote controller, you can:

■ Navigate and control all Media Center windows.

■ Control the video.

■ Place the computer in and out of Sleep mode.

Slim size remote controller

The Grand Tour

CD/DVD/HD D

DVD Menu

Volume +

Volume -

OK
Mute
Back

Start

Rewind

Replay

CD/DVD/HD DVD
button

LCD Brightness

VD Button

Down

Stop

Press this button to launch an application
program that allows Windows Media

LCD

Brightness Up

Power

LED On/Off

Arrows

More Information

Fast Forward
Paly/Pause

Skip

Player/DVD Video Player/HD DVD Video Player.

Brightness down Decreases the computer’s display panel

brightness in individual steps.

Brightness up Increases the computer’s display panel

brightness in individual steps.

User’s Manual 2-14

The Grand Tour

Power Starts or terminate the operating system.This

button functions like the power button of your
computer. By default, the Sleep mode is
equivalent to the power off state of your computer.
To change the setting, click Start  Control

panel  System and Maintenance  Power
Options  Choose what the Power button
does. The following four options are available:

Do nothig, Sleep, Hibernate and Shut down.

Volu m e + Increases the volume while viewing DVDs or

replaying CDs.

Volu m e - Decreases the volume while viewing DVDs or

replaying CDs.

DVD menu Opens the main menu on a DVD movie, if

available.

Arrows Moves the cursor to navigate within Media Center

windows.

OK Selects the desired action or window option.

It acts like the ENTER Key.

LED on/off Pressing this button to switch the lighting of

indicators.

Mute Turns your computer sound off.

Back Displays the previous window.

More information The button provides more detail information.

Start Opens Media Center to the main window.

Rewind Moves the media (video, DVD, music, and so on)

backwards.

Play/Pause Plays the selected media. This button also acts as

a pause button.

Fast forward Moves the media (video, DVD, music, and so on)

forwards.

User’s Manual 2-15

The Grand Tour

Replay Moves media backward (seven seconds for

Stop Stops the media currently playing.

Skip Moves media forward (30 seconds for videos,

videos, one music track or one DVD chapter
at a time).

one music track or one DVD chapter).

Using the remote controller

Some computers include a remote control unit, which allows you to control
some of your computer’s functions from a distant location.

■ The remote controller is designed specifically for this computer.

■ Some application programs may not support remote control functions.

Operational range of the remote controller

Point the remote controller at your computer and press a button.
The operational angle and distance are described below.

Distance Within 5 meters from the infrared receiver

window.

Angle Within about 30 degrees horizontally and about

15degrees vertically of perpendicular to the
infrared receiver window.

User’s Manual 2-16

The Grand Tour

30 Degrees

15 Degrees
(Vertically)

Infrared Receiver
Window

Operational range of the remote controller

30 Degrees

Remote Controller

5m

Even if within the effective scope as described above, the remote controller
may malfunction or not work correctly in the following cases.

■ When an obstacle stands between the infrared receiver window of your

computer and the remote controller.

■ When direct sunlight or strong fluorescent light strikes the infrared

receiver window.

■ When the infrared receiver window or the infrared emission part of the

remote controller is dirty.

■ When other computers which use an infrared remote controller are

used near to your computer.

■ When a low battery condition is present.

Installing/Removing batteries

Be sure to install the provided CR2016 type batteries before using the
remote controller. The procedures for installing and removing the batteries
vary depending on the type of the remote controller. Check the type and
then install or remove the batteries as instructed.

User’s Manual 2-17

The Grand Tour

Store the battery for the remote controller beyond the reach of children.
If a child swallows a battery, this might result in choking. If it happens,

contact a doctor immediately.

Observe the following precautions when using the battery of the remote
controller.

■ Do not use batteries other than those specified.

■ Ensure that you insert the batteries with their polarities correctly

aligned (+ or -).

■ Do not recharge, heat, disassemble or short the battery, or put it into

a fire or flame.

■ Do not use a battery whose "recommended expiration date" has been

reached, or which is completely discharged.

■ Do not use different types of batteries or old and new batteries at the

same time.

■ Do not carry the battery together with metal necklaces, hairpins or

other metal accessories.

■ When storing or disposing of used batteries, make sure to put some

insulation tape on their terminals (+ and -) to avoid short-circuits.

If these precautions are not followed, heating, fluid leakage or explosion
may occur. This may cause burns or personal injury. If battery fluid gets
on your skin or clothes, wash immediately with clean water. If battery fluid
gets in your eyes, rinse your eyes with clean water immediately and see
a doctor. Do not touch the battery fluid on instruments or devices with bare
hands. Wipe off with a cloth or paper towel.

Type of battery that can be used for the remote controller

When the provided batteries run down, please replace them with adequate
ones. CR2016 type battery is available. Other types or battery should not
be used.

Installing the batteries

1. Open the battery cover on the back side of the remote controller.

Battery Cover

Opening the battery cover

User’s Manual 2-18

The Grand Tour

2. Be sure to place the batteries with correct polarities. Press the battery
down to the stopper then push it forward to fit into the battery case.

BatteryStopper

Inserting the batteries

3. Close the battery cover. Close the cover securely until it clicks.

Closing the battery cover

Replacing the batteries

When the batteries in the remote controller reach the end of their life, the
remote controller may not operate correctly or work only within a short
distance from your computer. In this instance, you should purchase new
batteries and replace the discharged ones.

Slim size remote controller

1. Open the battery cover on the back side of the remote controller.

2. Hold down the stopper and slide the battery out of battery case.

BatteryStopper

Removing the batteries

User’s Manual 2-19

3. Insert the battery in place. Be sure to place the batteries with correct
polarities. Press the battery down to the stopper then push it forward to
fit into the battery case.

4. Close the battery cover. Close the cover securely until it clicks.

Placing the slim size remote controller

Inserting a slim size remote controller

To insert the slim size remote controller, follow the setps below.

1. Make sure the ExpressCard slot is empty.

2. Set the front side upward and insert the slim size remote controller.

Slim size remote

controller

The Grand Tour

Inserting the slim size remote controller

3. Press gently to ensure a firm connection.

Remove a slim size remote controller

To remove the slim size remote controller, follow the steps below.

1. Press the slim size remote controller slightly to make it stretch out.

2. Grasp the slim size remote controller and pull it out from the slot.

User’s Manual 2-20

Getting Started

This chapter provides basic information to get you started using your
computer. It covers the following topics:

Be sure also to read the Instruction Manual for Safety and Comfort.
This guide, which is included with the computer, explains product liability.

■ Installing the battery pack

■ Connecting the AC adaptor

■ Opening the display

■ Turning on the power

■ Windows Vista™ setup

■ Turning off the power

■ Restarting the computer

■ System Recovery Options and Restoring the preinstalled Software

All users should be sure to read the section Windows® Vista setup.

Getting Started

Chapter 3

Installing the battery pack

Skip this section, if your computer came with the battery pack installed.
To install the battery pack, follow the steps below.

■ The battery pack is a lithium ion battery, which can explode if not

properly replaced, used, handled or disposed of. Dispose of the battery
as required by local ordinances or regulations. Use only batteries
recommended by TOSHIBA as replacements.

■ Do not touch the latch while holding the computer. Or you may get

injured by the dropped battery by unintentional release of the latch.

■ Please do not push the power button before installing the battery pack.

1. Turn the computer's power off.

2. Disconnect all cables connected to the computer.

3. Insert the battery pack. The Battery Release Latch clicks into place.

User’s Manual 3-1

Getting Started

4. Secure the Battery Pack Lock to ensure the battery is locked into place.
Later, when you want to remove the battery you must disengage this
lock first.

Battery

Pack

Lock

Connecting the AC adaptor

Attach the AC adaptor when you need to charge the battery or you want to
operate from AC power. It is also the fastest way to get started, because
the battery pack will need to be charged before you can operate from
battery power.

The AC adaptor can be connected to any power source supplying from 100
to 240 volts and 50 or 60 hertz. For details on using the AC adaptor to
charge the battery pack, refer to Chapter 6, Power and Power-Up Modes.

Use only the AC adaptor supplied as an accessory. Other AC adaptors
have different voltage and terminal polarities and use of them may produce
heat and smoke or even result in fire or rupture.

Securing the battery pack

Battery
Release
Latch

User’s Manual 3-2

Getting Started

■ Use only the AC adaptor supplied with your computer or an equivalent

adaptor that is compatible. Use of any incompatible adaptor could
damage your computer. TOSHIBA assumes no liability for any damage
caused by use of an incompatible adaptor.

■ When you connect the AC adaptor to the computer, always follow the

steps in the exact order as described in the User's Manual. Connecting
the power cable to a live electrical outlet should be the last step
otherwise the adaptor DC output plug could hold an electrical change
and cause an electrical shock or minor bodily injury when touched. As
a general safety precaution, avoid touching any metal parts.

1. Connect the power cord to the AC adaptor.

Connecting the power cord to the AC adaptor

2. Connect the AC adaptor's DC output plug to the DC IN 19V jack on the
back of the computer.

Connecting the adaptor to the computer

3. Plug the power cord into a live wall outlet.

User’s Manual 3-3

Opening the display

The display panel can be rotated in a wide range of angles for optimal
viewing.

1. Lift the panel up and adjust it to the best viewing angle for you.

Use reasonable care when opening and closing the display panel. Opening
it vigorously or slamming it shut could damage the computer.

Getting Started

Opening the display

Turning on the power

This section describes how to turn on the power.

After you turn on the power for the first time, do not turn it off until you have
set up the operating system. Refer to the section Windows Vista™ setup.

Press and hold the computer's power button for two or three seconds.

User’s Manual 3-4

Windows Vista™ setup

When you turn on the power for the first time, the computer's initial screen
is the Microsoft

Follow the on-screen directions.

Be sure to read the Windows End User License Agreement display
carefully.

®

Windows Vista™ Startup Screen Logo.

Getting Started

Turning on the power

Turning off the power

The power can be turned off in one of the following modes: Shut down
(Boot), Hibernation or Sleep Mode.

Shut Down mode (Boot mode)

When you turn off the power in Shut Down mode no data is saved and the
computer will boot to the operating system’s main screen.

1. If you have entered data, save it to the hard disk.

2. Make sure all disk (disc) activity has stopped, then remove the
CD/DVDs.

Make sure the Disk LED and ODD indicator indicators are off. If you turn
off the power while a disk (disc) is being accessed, you can lose data or
damage the disk (disc).

3. Click then click the arrow icon located in the power management
button . From the pull down menu, choose Shut Down.

4. Turn off the power to any peripheral devices.

User’s Manual 3-5

Do not turn the computer or devices back on immediately. Wait a moment
to let all capacitors fully discharge.

Sleep Mode

If you have to interrupt your work, you can turn off the power without exiting
from your software. Data is maintained in the computer's main memory.
When you turn on the power again, you can continue working right where
you left off.

■ When the AC adaptor is connected, the computer will go into Sleep

Mode according to the settings in the Power Options.

■ To restore operation from Sleep Mode, press the power button or press

any key. The latter action works only if Wake-up on Keyboard is
enabled in HW Setup.

■ If the computer automatically enters Sleep Mode while a network

application is active, the application might not be restored when the
computer wakes up from Sleep Mode.

■ To prevent the computer from automatically entering Sleep Mode,

disable Sleep Mode in the Power Options. That action, however, will
nullify the computer's Energy Star compliance.

■ Before entering Sleep Mode, be sure to save your data.

■ Do not install or remove a memory module while the computer

is in Sleep Mode. The computer or the module could be damaged.

■ Do not remove the battery pack while the computer is in Sleep Mode

(unless the computer is connected to an AC power source). Data in
memory will be lost.

Getting Started

Benefits of Sleep Mode

The Sleep Mode feature provides the following benefits:

■ Restores the previous working environment more rapidly than

Hibernation Mode.

■ Saves power by shutting down the system when the computer receives

no input or hardware access for the duration set by the System Sleep
Mode feature.

■ You can use the panel power off feature.

Entering Sleep Mode

You can enter Sleep Mode in one of three ways:

■ Click Start then click the power button ( ) located in the power

management buttons ( ).
Please note that this feature must be enabled within the Power Options

(to access it, click  Control Panel  System and
Maintenance  Power Options).

User’s Manual 3-6

■ Click , click power button located in the power management

buttons , or click arrow button and select Sleep from
the menu.

■ Close the display panel. This feature must be enabled. Please refer to

the Power Options (to access it, click  Control Panel  System
and Maintenance  Power Options).

When you turn the power back on, you can continue where you left when
you shut down the computer.

You can also enable Sleep Mode by pressing Fn + F3. Refer to Chapter 5,

The Keyboard, for details.

■ When the computer is shut down in Sleep Mode, the power indicator

flashes orange.

■ If you are operating the computer on battery power, you can lengthen

the operating time by turning it off into Hibernation Mode, as Sleep
Mode consumes more power.

Sleep Mode limitations

Sleep Mode will not function under the following conditions:

■ Power is turned back on immediately after shutting down.

■ Memory circuits are exposed to static electricity or electrical noise.

Hibernation Mode

The hibernation feature saves the contents of memory to the hard disk
when the computer is turned off. The next time the computer is turned on,
the previous state is restored. The hibernation feature does not save the
status of peripheral devices.

■ Save your data. While entering Hibernation Mode, the computer saves

the contents of memory to the HDD. However, for safety sake, it is best
to save your data manually.

■ Data will be lost if you remove the battery or disconnect the AC adaptor

before the save is completed. Wait for the disk indicator to go out.

■ Do not install or remove a memory module while the computer is in

Hibernation Mode. Data will be lost.

Getting Started

Benefits of Hibernation Mode

The Hibernation Mode feature provides the following benefits:

■ Saves data to the hard disk when the computer automatically shuts

down because of a low battery.

■ You can return to your previous working environment immediately when

you turn on the computer.

User’s Manual 3-7

Getting Started

■ Saves power by shutting down the system when the computer receives

no input or hardware access for the duration set by the System
hibernate feature.

■ You can use the panel power off feature.

Starting Hibernation Mode

You can also enable Hibernation Mode by pressing Fn + F4. Refer to
Chapter 5, The Keyboard, for details.

To enter Hibernation Mode, follow the steps below.

1. Click .

2. Click the arrow icon located in the power management button

3. From the pull down menu, select Hibernate.

.

Automatic Hibernation Mode

The computer will enter Hibernation mode automatically when you press
the power button or close the Display Screen. First, however, make the
appropriate settings according to the steps below.

1. Open the Control Panel.

2. Open System and Maintenance and open Power Options.

3. Select the Choose what the power button does.

4. Enable the desired Hibernation settings for When I press the power
button and When I close the lid.

5. Click the Save changes button.

Data saving in Hibernation Mode

When you turn off the power in Hibernation Mode, the computer takes a
moment to save current memory data to the hard disk. During this time, the
disk indicator will light.

After you turn off the computer and memory is saved to the hard disk, turn
off the power to any peripheral devices.

Do not turn the computer or devices back on immediately. Wait a moment
to let all capacitors fully discharge.

Restarting the computer

Certain conditions require that you reset the system. For example, if:

■ You change certain computer settings.

■ An error occurs and the computer does not respond to your keyboard

commands.

User’s Manual 3-8

Getting Started

There are three ways to reset the computer system:

1. Click then click the arrow icon located in the power management
button , and select Restart from the pull down menu.

2. Press Ctrl + Alt + Del, then select Restart from the Shut down
options.

3. Press the power button and hold it down for five seconds. Once the
computer has turned itself off, wait between ten and fifteen seconds
before turning it on again with the power button.

System Recovery Options and Restoring the pre-installed Software

System Recovery Options

About 1.5 GB hidden partition is allocated on the hard disk drive for the
System Recovery Options.

This partition stores files which can be used to repair the system in the
event of a problem.

The System Recovery Options feature will be unusable if this partition is
deleted.

The System Recovery Options feature is installed on the hard disk when
shipped from the factory. The System Recovery Options menu includes
tools to repair startup problems, run diagnostics or restore the system.

See the Windows Help and Support content for more information about
Startup Repair.

The System Recovery Options can also be run manually to repair
problems.

The procedure is as follows. Follow the instructions shown on the on­screen menu.

1. Turn off the computer.

2. Turn on the computer and when the TOSHIBA screen appears
repeatedly press the F8 key.

3. The Advanced Boot Options menu will be displayed.
Use the arrow keys to select Repair Your Computer and press
ENTER.

4. Follow the on-screen instructions.

The Windows Vista® CompletePC Backup feature can be used on
Windows Vista

®

Business Edition and Ultimate Edition.

User’s Manual 3-9

Restoring the pre-installed Software

Depending on the model you purchased, different ways for restoring the
pre-installed software are offered:

■ Creating optical Recovery Discs

■ Restoring the pre-installed software from your created Recovery Discs.

■ Restoring the pre-installed software from the Recovery hard disk drive.

Creating Optical Recovery Discs

This section describes how to create Recovery Discs.

■ Be sure to connect the AC adaptor when you create Recovery Discs.

■ Be sure to close all other software programs except the Recovery Disc

Creator.

■ Do not run software such as screen savers which can put a heavy load

on the CPU.

■ Operate the computer at full power.

■ Do not use power-saving features.

■ Do not write to the disc when the virus check software is running. Wait

for it to finish, then disable virus detection programs including any
software that checks files automatically in the background.

■ Do not use utilities, including those intended to enhance hard disk drive

access speed. They may cause unstable operation and damage data.

■ Do not shut down/log off or Sleep/Hibernate while writing or rewriting

the disc.

■ Set the computer on a level surface and avoid places subjected to

vibrations such as airplanes, trains or cars.

■ Do not place your computer on unstable tables or any other unstable

surfaces.

A recovery image of the software on your computer is stored on the hard
disk drive, and can be copied to DVD media by using the following steps:

1. Have a blank DVD media ready.

2. The application will allow you to choose from a variety of different media
onto which the recovery image can be copied including DVD-R, DVD­RW, DVD+R, DVD+RW.

Getting Started

Please note that some of the above media may not be compatible with the
optical disc drive installed into your computer. You should therefore verify
the optical disc drive supports the blank media you have chosen before
proceeding.

3. Turn on your computer and allow it to load the Windows Vista®
operating system from the hard disk drive as normal.

4. Insert the first blank media into the optical disc drive tray.

®

5. Double click the Recovery Disc Creator icon on the Windows Vista
desktop, or select the application from Start Menu.

User’s Manual 3-10

Getting Started

6. After Recovery Disc Creator starts, select the type of media and the title
you wish to copy, and then click the Create button.

7. Follow the on-screen instructions.

Your Recovery Discs will be created.

Restoring the pre-installed software from your created Recovery
Discs

If the pre-installed files are damaged, you are able to use the Recovery
Discs you have created to restore the computer to the state it was in when
you originally received it. To perform this restoration, follow the steps
below:

When the sound mute feature has been activated by pressing the
Fn + ESC key, be sure to disable this to allow sounds to be heard before
starting the restore process. Please refer to Chapter 5, The Keyboard, for
further details.

When you reinstall the Windows operating system, the hard disk will be
reformatted and all data will be lost.

1. Load the Recovery Discs into the optical disc drive and turn off the
computer's power.

2. While holding down F12 key on the keyboard, turn on your computer ­when the TOSHIBA logo screen appears, release the F12 key.

3. Use the cursors key to select the CD-ROM icon from the menu. Please
refer to the Boot Priority section in Chapter 7, HW Setup & BIOS Setup
for further information.

4. A menu will be displayed from which you should follow the on-screen
instructions.

Restoring the pre-installed software from the Recovery hard disk
drive

On your Data drive you may find a folder "HDDRecovery". This folder
stores files which can be used to recover your system to the originally
installed factory state.

If you subsequently set up your hard disk drive again, do not change,
delete or add partitions in a manner other than specified in the manual,
otherwise you may find that space for the required software is not available.

In addition, if you use a third-party partitioning program to reconfigure the
partitions on your hard disk drive, you may find that it becomes impossible
to setup your computer.

When the sound mute feature has been activated by pressing the
Fn + ESC key, be sure to disable this to allow sounds to be heard before
starting the restore process. Please refer to Chapter 5, The Keyboard, for
further details.

User’s Manual 3-11

Getting Started

Be sure to connect the AC adaptor, otherwise you may run out of battery
during the recovery process.

When you reinstall the Windows operating system, the hard disk will be
reformatted and all data will be lost.

1. Turn off the computer.

2. Turn on the computer and when the TOSHIBA screen appears
repeatedly press the F8 key.

3. The Advanced Boot Options menu will be displayed.
Use the arrow keys to select Repair Your Computer and press
ENTER.

4. Select your preferred keyboard layout and press Next.

5. To access the recovery process please log on as an enabled user with
sufficent rights.

6. Click TOSHIBA HDD Recovery on the System Recovery Options
screen.

7. Follow the on-screen instructions on the TOSHIBA HDD Recovery
dialog.

The computer will be restored to its factory state.

User’s Manual 3-12

Operating Basics

This chapter gives information on basic operations including using the
TouchPad, fingerprint sensor (optional), USB Sleep and Charge function,
web camera (optional), internal microphone (optional), optical media
drives, sound system, modem, Wireless LAN and LAN. It also provides tips
on caring for your computer.

Using the TouchPad

To use the TouchPad, simply touch and move your finger tip across it in the
direction you want the on-screen pointer to go.

Operating Basics

Chapter 4

TouchPad

TouchPad

control buttons

TouchPad and TouchPad control buttons

Two buttons below the keyboard are used like the buttons on a mouse
pointer. Press the left button to select a menu item or to manipulate text or
graphics designated by the pointer. Press the right button to display a menu
or other function depending on the software you are using.

User’s Manual 4-1

Do not press the TouchPad too hard or press a sharp object such as a ball
point pen against the TouchPad. The TouchPad could be damaged.

For some functions, you can tap the TouchPad instead of pressing a control
button.

Click: Tap the TouchPad once.
Double-click: Tap the TouchPad twice.
Drag and drop: 1. Hold down the left control button and move the cursor

to drag the item you want to move.

2. Lift your finger to drop the item where you want it.
Scroll: Vertical: Move your finger up or down the right edge of

the TouchPad.
Horizontal: Move your finger left or right along the

bottom edge of the TouchPad.

Using the fingerprint sensor (optional)

Some models in the series have a fingerprint utility installed for the purpose
of enrolling and recognizing fingerprints. By enrolling the ID and password
to the fingerprint authentication device, it is no longer necessary to input
the password from the keyboard. Just by swiping the finger against the
fingerprint sensor, the following functions will be enabled:

■ Logon to Windows and access a security-enabled homepage through

IE (Internet Explorer).

■ Files and folders can be encrypted/decrypted and third party access to

them prevented.

■ Disable the password-protected screen-saver when returning from

power-saving (Sleep) mode.

■ Pre-OS feature and Single Sign-On feature.

■ Authentication of the User Password and Hard Disk Password when

booting up the computer.

To "swipe" refers to the action of reading a fingerprint using the fingerprint
sensor.

Operating Basics

How to swipe the finger

Using the following steps when swiping fingers for fingerprint registration
or authentication will help to minimize authentication failures:

1. Align the first joint of the finger to the center of the sensor. Lightly touch
the sensor and swipe finger levelly towards you.

2. While lightly touching the sensor, swipe the finger towards you until the
sensor surface becomes visible.

3. Ensure the center of the fingerprint is on the sensor when swiping the
finger.

User’s Manual 4-2

Operating Basics

Slide the finger over the recognition sensor

■ Avoid swiping with the finger stiff or pressed-on too hard:

Fingerprint reading may fail if the center of the fingerprint is not
touching on the sensor, or when finger is swiped while pressing hard.
Make sure that the center of the fingerprint is touching the sensor
before swiping.

■ Confirm the center of the fingerprint whirl before swiping:

The thumb’s fingerprint has a bigger whirl, which is prone to
misalignment and distortions. This will cause difficulty in registration
and a drop in the authentication success rate. Always confirm the
center of the fingerprint whirl so that it is swiped along the centerline
of the sensor.

■ When fingerprint reading is not successful:

There is a possibility of authentication failures if the finger is swiped too
quickly or too slowly. Follow the onscreen instructions to adjust the
speed of the swipe.

Points to note about the fingerprint sensor

Failure to follow these guidelines might result in (1) damage to the sensor
or cause sensor failure, (2) finger recognition problems, or lower finger
recognition success rate.

■ Do not scratch or poke the sensor with your nails or any hard or sharp

objects.

■ Do not press the sensor strongly.

■ Do not touch the sensor with a wet finger or any wet objects.

Keep sensor surface dry and free of water vapor.

■ Do not touch the sensor with a soiled finger. Minute foreign particles

on a soiled or dirty finger may scratch the sensor.

■ Do not paste stickers or write on the sensor.

■ Do not touch the sensor with a finger or any object with built-up static

electricity.

Observe the following before you place your finger on the sensor whether
for fingerprint enrollment/registration or recognition.

User’s Manual 4-3

Operating Basics

■ Wash and dry your hands thoroughly.

■ Remove static electricity from your fingers by touching any metal

surface. Static electricity is a common cause of sensor failures,
especially when the weather is dry.

■ Clean the sensor with a lint-free cloth. Do not use detergent to clean the

sensor.

■ Avoid the following finger conditions for enrollment or recognition

as they may result in fingerprint enrollment errors or a drop in the
fingerprint recognition success rate.

■ Soaked or swollen finger (e.g. after taking bath)

■ Injured finger

■ Wet finger

■ Soiled or oily finger

■ Extremely dry skin condition on finger

Observe the following to improve the fingerprint recognition success rate.

■ Enroll two or more fingers.

■ Enroll additional fingers if recognition failure occurs often using enrolled

fingers.

■ Check your finger condition. Changed conditions, such as injured,

rough, extremely dry, wet, soiled, dirty, oily, soaked, swollen fingers,
may lower the recognition success rate. Also if the fingerprint is worn
down or the finger becomes thinner or fatter, the recognition success
rate may be lowered.

■ The fingerprint for each finger is different and unique. Please ensure

that only the registered or enrolled fingerprint or fingerprints are used
for identification.

■ Check sliding position and speed.

■ Fingerprint data can be enrolled up to 30~34 times.

■ Fingerprint data is stored into the nonvolatile memory in the fingerprint

sensor. Deleting fingerprint data with Delete menu on Fingerprint
Software Management before you dispose the computer is
recommended.

How to delete the fingerprint data

Saved fingerprint data is stored in the Non-volatile memory inside the fin­gerprint sensor. If you hand over the PC to others, or dispose of it, to do the
following operations are recommended.

1. Click Start, point to All Programs, point to TrueSuite Access
Manager and click it.

2. The TrueSuite Access Manager Fingerprint Software screen is
displayed.

3. Enter your Windows Password and click Next to enter the Control
Center. Or swipe your enrolled finger to enter the Control Center.

4. Click Delete All Fingerprints.

User’s Manual 4-4

Fingerprint sensor limitations

■ The fingerprint sensor compares and analyzes the unique

characteristics in a fingerprint.

■ A warning message will be displayed when recognition is abnormal

or recognition is not successful within a fixed duration.

■ The recognition success rate may differ from user to user.

■ Toshiba does not guarantee that this fingerprint recognition technology

will be error-free.

■ Toshiba does not guarantee that the fingerprint sensor will recognize

the enrolled user or accurately screen out unauthorized users at all
times.Toshiba is not liable for any failure or damage that might arise out
of the use of this fingerprint recognition software or utility.

Points to note about the fingerprint utility

■ If Windows Vista™’s file encryption function EFS (Encryption File

System) is used to encrypt a file, the file cannot be further encrypted
using the encryption function of this software.

■ You can back up the fingerprint data or the information registered to

Password Bank.

■ Please use Import/Export menu on Fingerprint Software Management.

■ Please also refer to the fingerprint utility Help file for more information.

You can start it using the following method:

■ Click Start, point to All Programs, point to TrueSuite Access

Manager and click Document.

■ Click Start, point to All Programs, point to TrueSuite Access

Manager and click it. The main screen is displayed. Click Help

in the upper right corner of the screen.

Operating Basics

Set up procedure

Please use the following procedure when first using fingerprint
authentication.

Fingerprint registration

Enroll the required authentication data using the Fingerprints Enrollment
Wizard.

■ The fingerprint authentication uses the same Windows logon ID and

password. If the Windows logon password has not been setup, please
do so before registration.

■ Up to 30~34 fingerprint patterns can be registered.

1. Click Start, point to All Programs, point to TrueSuite Access
Manager and click it. Or double click the icon in the Task Bar.

2. The Enter Windows Password screen is displayed. Enter a password
into the Enter Windows Password field. Click Next.

User’s Manual 4-5

3. The Control Center screen is displayed. Click the non-enrolled finger
icon above the finger.

4. The Fingerprint Enrollment screen is displayed. Confirm the message
and click Next.

5. The Scanning Practice screen is displayed. You can practice swiping
your finger. When you have finished practicing swiping your finger, click
Next.

6. The Fingerprint Image Capture screen is displayed. Follow the
onscreen instructions and use the same finger you have selected under
the Control Center to swipe your finger with good images three times for
the fingerprint template to be created.

7. In case of finger injury or authentication failure, it is recommended that
another fingerprint also be enrolled. The following message will be
displayed: [We recommended enrolling at least two
fingerprint images.] Click OK and repeat steps 3, 4, 5 and 6 with
another finger.

Windows logon via fingerprint authentication

In place of the usual Windows logon by ID and password, fingerprint
authentication also allows logon to Windows.

This is useful especially when many users are using the PCs, as user
selection can be skipped.

Fingerprint authentication procedure

1. Start up the computer.

2. The Logon Authorization screen is displayed. Choose any of the
enrolled fingers and swipe the fingerprint on the sensor. If
authentication is successful, the user will be logged on to Windows.

■ If the fingerprint authentication fails, please logon using the Windows

logon password.

■ Please logon using the Windows logon password if the fingerprint

authentication failed for five times. To logon using the Windows logon
password, enter the Windows logon password at the [Welcome]
screen as normal.

■ A warning message will be displayed when authentication is abnormal

or authentication is not successful within a fixed duration.

Operating Basics

User’s Manual 4-6

Fingerprint system boot authentication

General

The fingerprint authentication system can be used to replace the keyboard
based User Password authentication system when booting up.

If you do not want to use the fingerprint authentication system for password
authentication when booting up, but prefer to use the keyboard-based
system instead, press the BACK SPACE key when the Fingerprint System
Boot Authentication screen is displayed. This will switch the password input
screen to the keyboard-based one.

■ It is necessary to register the User Password before using the

fingerprint Pre-OS feature and its extended function, the fingerprint
Single Sign-On feature. Please use TOSHIBA HW Setup to register the
User Password.

■ If you fail fingerprint authentication more than five times, you must

enter the User Password or Supervisor Password manually to start the
computer.

■ When swiping, please do it slowly and at a constant speed. If this does

not improve the authentication rate, please adjust the speed.

■ If there are any changes in the environment or settings related to

authorization, you will be required to provide authorization information
such as a User Password and HDD password.

Operating Basics

How to enable fingerprint system boot authentication
settings

It is necessary to first enroll your fingerprint with the TrueSuite Access
Manager application prior to enabling and configuring the fingerprint
Pre-OS feature.

Check that your fingerprint is enrolled before configuring the settings.

1. Swipe your finger across the fingerprint sensor. Or enter Windows
password and click Next.

2. Click settings.

3. The Administrator Settings screen is displayed. Place a checkmark
in "Enable Pre-OS Fingerprint Authentication" and click OK.

The modified configuration for fingerprint Pre-OS feature becomes effective
the next time the system is booted up.

User’s Manual 4-7

Fingerprint Single Sign-On feature

General

This is a feature that allows the user to complete the authentication for
both the User Password (and optionally, the HDD user and Supervisor
passwords) and logging on to Windows using only one fingerprint
authentication when booting up. It is necessary to register the User
Password and Windows Logon password before using the fingerprint
Pre-OS feature and this fingerprint Single Sign-On feature. Please use
TOSHIBA HW Setup to register your User Password.

Only one fingerprint authentication is required to replace the User
Password (and, if selected, the HDD user and Supervisor passwords)
and Windows Logon password.

How to enable fingerprint Single Sign-On feature

It is necessary to first enroll your fingerprint with the TrueSuite Access
Manager application prior to enabling and configuring the fingerprint Single
Sign-On feature. Check that the fingerprint is enrolled before configuring
the settings.

1. Swipe your finger across the fingerprint sensor. Or enter Windows
password and click Next.

2. Click settings.

3. The Administrator Settings screen is displayed. Place a checkmark
in "Enable Pre-OS Fingerprint Authentication".

4. Then, place a checkmark in "Enable Single Sign-On Fingerprint
Authentication" and click OK.

The modified configuration for the fingerprint Single Sign-On feature
becomes effective the next time the system is booted up.

Operating Basics

Fingerprint utility limitations

TOSHIBA does not guarantee that the fingerprint utility technology will be
completely secure or error-free. TOSHIBA does not guarantee that the
fingerprint utility will accurately screen out unauthorized users at all times.
TOSHIBA is not liable for any failure or damage that might arise out of the
use of the fingerprint software or utility.

USB Sleep and Charge function

Your computer can supply USB bus power (DCSV) to the USB port even
when the power of the computer is turned OFF. "Power OFF" includes
Sleep Mode, Hibernation Mode or shutdown state.

This function can only be used for ports that support the USB Sleep and
Charge function (hereinafter called "compatible ports").

Compatible ports are USB ports that have the ( ) symbol icon.

User’s Manual 4-8

Operating Basics

You can use the "USB Sleep and Charge function" to charge certain USB­compatible external devices such as mobile phones or portable digital
music players.

However, the "USB Sleep and Charge function" may not work with certain
external devices even if they are compliant with the USB specification. In
those cases, turn the power of the computer ON to charge the device.

■ The "USB Sleep and Charge function" only works for compatible ports.

This function is disabled in the default setting. To enable it, you must
change [Disabled] to [Enabled] in the HW setup.

■ When "USB Sleep and Charge function" is set to [Enabled] in HW

Setup, USB bus power (DC5V) will be supplied to compatible ports
even when the power of the computer is turned "OFF".
USB bus power (DC5V) is similarly supplied to the external devices
which are connected to the compatible ports. However, some external
devices cannot be charged solely by supplying USB bus power
(DC5V).
As for the specifications of the external devices, please contact the
device manufacturer or check the specifications of the external devices
thoroughly before use.

■ Using the USB sleep and charge function to charge external devices

will take longer than charging the devices with their own chargers.

■ If external devices are connected to compatible ports when the AC

adaptor is not connected to the computer, the battery of the computer
will be depleted even when the power of the computer is turned OFF.
As such, we recommend that you connect the AC adaptor to the
computer when using the USD sleep and charge function.

■ External devices connected to the USB bus power (DC5V) function that

interfaces with the power ON/OFF of the computer may always be in
an operational state.

■ When there is a current overflow of the external devices connected to

the compatible ports, USB bus power (DC5V) supply may be stopped
for safety reasons.

Metal paper clips or hair pins/clips will generate heat if they come into
contact with USB ports. Do not allow USB ports to come into contact with
metal products, for example when carrying the computer in your bag.

How to enable/disable USB sleep and charge function

You can enable/disable the USB sleep and charge function in HW Setup.
Refer to the USB Sleep and Charge function in Chapter 7, HW Setup.

User’s Manual 4-9

Using the Web Camera (optional)

Some models in this series are equipped with a webcam utility, which can
capture still and video images. The web camera will auto-run when
Windows starts.

Please unstick the protective plastic-film before using the Web Camera.

Operating Basics

Built-in microphone

Web Camera LED

Web Camera Lens

Using the software

The web camera software is pre-configured to start when you turn on
Windows Vista; if you need to restart it go to Start  All Programs 
Camera Assistant Software  Camera Assistant Software.

Capture Still

Images

Effects Mute

User’s Manual 4-10

Video

Recording

Audio

Recording

Function

Display Window

Camera resolution

Operating Basics

Capture Still Images Click to see a preview of the captured image;

Video Recording Click to prepare for recording. Click again to start

Audio Recording Click to start recording, click again to stop and

Function Access additional functions: About, Player,

About Displays software manufacturer details.
Player Play video files.
Effects Choose images to be displayed on the capture

Properties Choose from the Options tab to flip, zoom, flicker

Settings Choose from the: Options tab to change the tool

Help Displays the help files for the software.

you can also e-mail the image.

recording. One more to stop recording and see
preview of the video.

listen to a preview of the audio.

Effects, Properties, Settings and Help.

screen.

rate, night mode and backlight compensation; in
the Image tab change the color settings; in the
Profiles tab change the lighting conditions.

bar position; the Picture tab to select picture
output options such as size, export file and save
path; the Video tab to choose video output
settings such as Frame Rate, Size, Compression
and the frame rate, size, record compressor, and
save path; the Audio tab to change the audio
device, audio compressor, audio volume and
save path.

Using the microphone (optional)

Some models in this series are equipped with a built-in microphone that
can be used to record monaural sounds into your applications. It can also
be used to issue voice commands to applications that support such
functions.

If your computer has a built-in microphone and speakers, "feedback" may
be heard under certain conditions. Feedback occurs when sound from the
speaker is picked up in the microphone and amplified back to the speaker,
which amplifies it again to the microphone.

This feedback occurs repeatedly and causes a very loud, high-pitched
noise. It is a common phenomenon that occurs in any sound system when
the microphone input is output to the speaker (throughput) and the speaker
volume is too loud or too close to the microphone. You can control
throughput by adjusting the volume of your speaker or through the Mute
function in the Master Volume panel. Refer to your Windows documentation
for details on using the Master Volume panel.

User’s Manual 4-11

Using the optical disc drive

Operation is the same for all optical media drives. The full-size drive
provides high-performance execution of CD/DVD-based programs.
You can run either 12 cm (4.72") or 8 cm (3.15") discs without an adaptor.
An ATAPI interface controller is used for CD/DVD operation. When the
computer is accessing a CD/DVD, an indicator on the drive glows.

Refer also to the Writing CD/DVD with the DVD Super Multi drive or

HD DVD-ROM drive supporting DVD±R DL section for precautions on

writing to CDs/DVDs.

Loading discs

To load a disc, follow the steps below.

1. a. When the power is on, press the eject button to open the drawer

slightly.

Operating Basics

Eject Button

Pressing the eject button

User’s Manual 4-12

Operating Basics

b. Pressing the eject button will not open the drawer when the disc

drive's power is off. If the power is off, you can open the drawer by
inserting a slender object (about 15 mm) such as a straightened
paper clip into the eject hole just to the right of the eject button.

Manual release with the eject hole

2. Grasp the drawer gently and pull until it is fully opened.

Pulling the drawer open

User’s Manual 4-13

Operating Basics

3. Place the disc, label side up, in the drawer.

Inserting a disc

When the drawer is fully opened, the edge of the computer will extend
slightly over the disc tray. Therefore, you will need to turn the disc at an
angle when you place it in the tray. After seating the disc, however, make
sure it lies flat, as shown in the figure above.

■ Do not touch the laser lens. Doing so could cause misalignment.

■ Keep foreign matter from entering the drive. Check the back edge of

the tray to make sure it carries no debris before closing the drive.

4. Press gently at the centre of the disc until you feel it click into place. The
disc should lie below the top of the spindle, flush with the spindle base.

5. Push the center of the drawer to close it. Press gently until it locks into
place.

If the disc is not seated properly when the drawer is closed, the disc might
be damaged. Also, the drawer might not open fully when you press the
eject button.

User’s Manual 4-14

Closing the disc drawer

Removing discs

To remove the disc, follow the steps below.

Do not press the eject button while the computer is accessing the disc
drive. Wait for the optical media drive indicator to go out before you open
the drawer. Also, if the disc is spinning when you open the drawer, wait for
it to stop before you remove it.

1. To pop the drawer partially open, press the eject button. Gently pull the
drawer out until it is fully opened.

Operating Basics

■ When the drawer pops open slightly, wait a moment to make sure the

disc has stopped spinning before pulling the drawer fully open.

■ Turn off the power before you use the eject hole. If the disc is spinning

when you open the drawer, the disc could fly off the spindle and cause
injury.

2. The disc extends slightly over the sides of the drawer so you can hold it.
Hold the disc gently by its edges and lift it out.

User’s Manual 4-15

Operating Basics

Removing a disc

3. Push the centre of the drawer to close it. Press gently until it locks into
place.

Writing CD/DVD with the DVD Super Multi drive or HD DVD­ROM drive supporting DVD±R DL

Some models in this series are equipped with Writing CD/DVD with the
DVD Super Multi drive or HD DVD-ROM drive (Supporting DVD±R DL).

You can use the DVD Super Multi drive or HD DVD-ROM drive to write data
to either CD-R/RW or DVD-R/-RW/+R/+RW/-RAM discs. The following
applications for writing are preinstalled: TOSHIBA Disc Creator and
TOSHIBA Direct Disc Writer. Ulead Movie factory for TOSHIBA.

Important message (DVD Super Multi drive or HD DVD-ROM drive
supporting DVD±R DL)

Before you write or rewrite to CD-R/RW or DVD-R/-RW/+R/+RW/-RAM
discs, read and follow all setup and operating instructions in this section. If
you fail to do so, the DVD Super Multi drive or HD DVD-ROM drive may not
function properly, and you may fail to write or rewrite, lose data or incur
other damage.

User’s Manual 4-16

Before writing or rewriting

■ Based on TOSHIBA's limited compatibility testing, we suggest the

following manufacturers of CD-R/RW and DVD-R/+R/-RW/+RW/-RAM
discs. However, in no event does TOSHIBA guarantee the operation,
quality or performance of any disc. Disc quality can affect write or
rewrite success rates.

CD-R: TAIYO YUDEN Co., Ltd.

MITSUBISHI KAGAKU MEDIA CO, LTD.
Ricoh Co., Ltd.
Hitachi Maxell Ltd.

CD-RW: MITSUBISHI KAGAKU MEDIA CO, LTD.

Ricoh Co., Ltd.

High Speed
CD-RW:

Ultra Speed
CD-RW:

DVD-R: DVD Specifications for Recordable disc for

DVD-R(DL): MITSUBISHI KAGAKU MEDIA CO, LTD.
DVD+R: MITSUBISHI KAGAKU MEDIA CO, LTD.

DVD+R(DL): MITSUBISHI KAGAKU MEDIA CO, LTD.

DVD-RW: DVD Specifications for Recordable Disc for

DVD+RW: MITSUBISHI KAGAKU MEDIA CO, LTD.

DVD-RAM: DVD Specifications for DVD-RAM Disc for

MITSUBISHI KAGAKU MEDIA CO, LTD.
Ricoh Co., Ltd.

MITSUBISHI KAGAKU MEDIA CO, LTD.

General Version2.0

TAIYO YUDEN Co., Ltd.
Matsushita Electric Industrial Co., Ltd.

Ricoh Co., Ltd.

Version 1.1 or 1.2

Victor Company of Japan, Ltd. (JVC)
MITSUBISHI KAGAKU MEDIA CO, LTD.

Version2.0, 2.1 or 2.2

Hitachi Maxell Ltd.
Matsushita Electric Industrial Co., Ltd.

Operating Basics

This drive cannot use discs that allow writing of 8speeds or more (DVD-R,
DVD+R, DVD+RW), or 6 speeds or more (DVD-RW)

■ If the disc is poor in quality, dirty or damaged, writing or rewriting errors

may occur. Be careful to check the disc for dirt or damage before you
use it.

■ The actual number of rewrites to CD-RW, DVD-RW, DVD+RW or

DVD-RAM is affected by the quality of the disc and the way it is used.

■ There are two types of DVD-R discs: authoring and general use discs.

Do not use authoring discs. Only general use discs can be written to by
a computer drive.

User’s Manual 4-17

Operating Basics

■ We can support only Format1 of DVD-R DL. Therefore you cannot do

the additional writing. If your data is under 4.7 GB, we suggest to use
DVD-R (SL) media.

■ You can use DVD-RAM discs that can be removed from a cartridge and

DVD-RAM discs designed without a cartridge. You can not use a disc
with a 2.6 GB single-sided capacity and 5.2 GB double-sided capacity.

■ Other DVD-ROM drives for computers or other DVD players may not be

able to read DVD-R/-RW or DVD+R/+RW discs.

■ Data written to a CD-R/DVD-R/DVD+R disc cannot be deleted either in

whole or in part.

■ Data deleted (erased) from a CD-RW, DVD-RW, DVD+RW and DVD-

RAM disc cannot be recovered. Check the content of the disc carefully
before you delete it. If multiple drives that can write data to discs are
connected, be careful not to delete data from the wrong drive.

■ In writing to a DVD-R/-RW, DVD+R/+RW or DVD-RAM disc, some disc

space is required for file management, so you may not be able to write
the full capacity of the disc.

■ Since the disc is based on the DVD standard, it might be filled with

dummy data if the written data is less than about 1 GB. Even if you write
only a small amount of data, it might take time to fill in the dummy data.

■ DVD-RAM formatted by FAT32 cannot be read in WindowsR 2000

without DVD-RAM Driver Software.

■ When multiple drives that can write data to discs are connected, be

careful not to write to the wrong drive.

■ Be sure to connect the AC adaptor before you write or rewrite.

■ Before you enter Sleep Mode/Hibernation Mode, be sure to finish DVD-

RAM writing. Writing is finished if you can eject DVD-RAM media.

■ Be sure to close all other software programs except the writing

software.

■ Do not run software such as a screen saver, which can put a heavy load

on the CPU.

■ Operate the computer under the power scheme High Performance.

Do not use power-saving features.

■ Do not write while virus check software is running. Wait for it to finish

and then disable virus detection programs including any software that
checks files automatically in the background.

■ Do not use hard disc utilities, including those intended to enhance HDD

access speed. They may cause unstable operation and data damage.

■ Write from the computer's hard disc drive to the CD/DVD. Do not try to

write from shared devices such as a LAN server or any other network
device.

■ Writing with software other than TOSHIBA Disc Creator is not

recommended.

User’s Manual 4-18

When writing or rewriting

Please observe/consider the following when you write or rewrite to a
CD-R/-RW, DVD-R/-RW/-RAM or DVD+R/+RW disc.

■ Do not perform any of the following actions when writing or rewriting:

■ Change users in the Windows

■ Operate the computer for any other function, including using

a mouse or TouchPad or closing/opening the LCD panel.

■ Start a communication application such as a modem.

■ Apply impact or vibration to the computer.

■ Install, remove or connect external devices, including the following:

ExpressCard, USB devices, external display, optical digital devices.

■ Use the audio/video control buttons to reproduce music or voice.

■ Open the DVD Super Multi drive or HD DVD-ROM drive.

■ Do not use shut down/log off and Sleep Mode/Hibernation Mode while

writing or rewriting.

■ Make sure writing or rewriting is completed before going into Sleep

Mode/Hibernation Mode. Writing is completed if you can open the DVD
Super Multi drive tray or HD DVD-ROM drive tray.

■ Set the computer on a level surface and avoid places subject to

vibration such as airplanes, trains, or cars. Do not use an unstable
surface such as a stand.

■ Keep mobile phones and other wireless communication devices away

from the computer.

■ Always copy data from the hard disk drive to the CD-R/-RW,DVD-R/

-RW/-RAM or DVD+R/+RW disc. Do not use cut-and-paste. The
original data will be lost if there is a write error.

®

Vista operating system.

Operating Basics

Disclaimer (DVD Super Multi drive or HD DVD-ROM drive supporting
DVD±R DL)

TOSHIBA does not bear responsibility for the following:

■ Damage to any CD-R/RW or DVD-R/-RW/+R/+RW/-RAM disc that may

be caused by writing or rewriting with this product.

■ Any change or loss of the recorded contents of CD-R/RW or

DVD-R/-RW/+R/+RW/-RAM disc that may be caused by writing or
rewriting with this product, or for any business profit loss or business
interruption that may be caused by the change or loss of the recorded
contents.

■ Damage that may be caused by using third party equipment or

software. Given the technological limitations of current optical disc
writing drives, you may experience unexpected writing or rewriting
errors due to disc quality or problems with hardware devices. Also,
it is a good idea to make two or more copies of important data, in
case of undesired change or loss of the recorded contents.

User’s Manual 4-19

Writing CDs/DVDs/HD DVDs on HD DVD-RW drive

The optical drive installed on this computer cannot write multiple sessions
on HD DVD-RW disc sessions. Once a disc has been written to once, it will
be finalized. Once finalized, no further writing to the disc will be possible
regardless of what portion of the total disc capacity was used.

You can use the HD DVD-RW drive to write data to either CD-R or CD-RW,
DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R (Double Layer),
DVD-RAM, HD DVD-R, HD DVD-R(Dual layer) discs. This computer is
provided with TOSHIBA Disc Creator and Ulead
to allow for the writing to CD, DVD and HD DVD media.

For further information on TOSHIBA Disc Creator and Ulead® DVD
MovieFactory
helps. Refer to HD DVD Guide for information on accessing the online
manual or online help.

■ Please refer to the Writable discs, Chapter 2 for details about the types

of writable CD, DVD and HD DVD discs that can be supported by this
computer.

■ Do not turn off the power to the optical disc drive while the computer is

accessing it as this may cause you to lose data.

■ CD-R/RW media cannot be accessed using the Create CD/DVD option

in Media Center.

■ To write data to CD-R/RW media, use the TOSHIBA Disc Creator

feature that is installed on your computer.

®

, please refer to each software's online manual or online

®

DVD MovieFactory®

Operating Basics

When writing information to media using an optical drive, you should
always ensure that you connect the AC adaptor to a live power socket. It is
possible that, if data is written while powered by the battery pack, the write
process may sometimes fail due to low battery power - these instances
data loss may occur.

Important message

Before you write or rewrite to any of the media supported by the HD DVD­RW drive, please read and follow all of the setup and operating instructions
in this section. If you fail to do so, you may find that the HD DVD-RW drive
may not function properly, and you may fail to write or rewrite information
successfully this may cause you to either lose data or incur other damage
to the drive or media.

Legal Footnotes

TOSHIBA does not bear responsibility for the following:

■ Damage to any CD-R, CD-RW, DVD-R, DVD-R (Dual Layer), DVD-RW,

DVD+R, DVD+R (Double Layer), DVD+RW, DVD-RAM. HD DVD-R.
HD DVD-R(Dual Layer) or HD DVD-RW disc that may be caused by
writing or rewriting with this product.

User’s Manual 4-20

■ Any change or loss of the recorded contents of CD-R, CD-RW,

DVD-R,DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R (Double
Layer),DVD+RW, DVD-RAM. HD DVD-R. HD DVD-R(Dual Layer) or
HD DVD-RW media that may be caused by writing or rewriting with this
product, or for any business profit loss or business interruption that may
be caused by the change or loss of the recorded contents.

■ Damage that may be caused by using third party equipment or

software.

Given the technological limitations of current optical disc writing drives, you
may experience unexpected writing or rewriting errors due to disc quality or
problems with hardware devices. In view of this, it is good practice to make
two or more copies of important data, in case of any undesired change or
loss of the recorded contents.

Before writing or rewriting

■ Based on TOSHIBA's limited compatibility testing, we suggest the

follow-ing manufacturers of CD-R, CD-RW, DVD-R, DVD-R (Dual
Layer), DVD-RW, DVD+R, DVD+R (Double Layer), DVD+RW,
DVD-RAM. HD DVD-R. HD DVD-R(Dual Layer) or HD DVD-RW media,
however, it must be noted that disc quality can affect write or rewrite
success rates. Please also be aware that in no event does TOSHIBA
guarantee the operation, quality or performance of any disc.

CD-R: TAIYO YUDEN CO., LTD.

MITSUBISHI KAGAKU MEDIA CO., LTD.
RICOH Co., Ltd.
Hitach Maxell Ltd.

CD-RW: (High-Speed, Multi Speed)

MITSUBISHI KAGAKU MEDIA CO., LTD.
RICOH Co., Ltd.

CD-RW: (Ultra-Speed)

MITSUBISHI KAGAKU MEDIA CO., LTD.

DVD-R: DVD Specifications for Recordable Disc for

General Version 2.0

TAIYO YUDEN CO., LTD.
Matsushita Electric Industrial Co., Ltd.

DVD+R: MITSUBISHI KAGAKU MEDIA CO., LTD.

RICOH Co., Ltd.

DVD-RW: DVD Specifications for Recordable Disc for

General Version 1.1 or 1.2

VICTOR COMPANY OF JAPAN.LIMITED
MITSUBISHI KAGAKU MEDIA CO., LTD.

DVD+RW: MITSUBISHI KAGAKU MEDIA CO., LTD.

RICOH Co., Ltd.

Operating Basics

User’s Manual 4-21

Operating Basics

DVD-RAM: DVD Specifications for DVD-RAM Disc for

General Version 2.0, 2.1 or 2.2

Matsushita Electric Industrial Co., Ltd.
Hitachi Maxell Ltd.

DVD+R DL: MITSUBISHI KAGAKU MEDIA CO., LTD.
DVD-R DL: MITSUBISHI KAGAKU MEDIA CO., LTD.
HD DVD-R: MITSUBISHI KAGAKU MEDIA CO., LTD.

Hitachi Maxell Ltd.

HD DVD-R DL: MITSUBISHI KAGAKU MEDIA CO., LTD.
HD DVD-RW: RITEK Co.

■ This drive cannot use discs that allow writing faster than 8x speed

(DVD-R, DVD+R and DVD+RW media), 6x speed (DVD-RW media),
5x speed (DVD-RAM media), 4x speed (DVD-R (Dual Layer) media
and DVD+R (Double Layer media).

■ Some types and formats of DVD-R (Dual Layer) and DVD+R (Double

Layer) discs may be unreadable.

■ 2.6 GB and 5.2 GB DVD-RAM media cannot be read from or written to.

■ DISC created in DVD-R (Dual Layer) format 4 (Layer Jump Recording)

cannot be read.

■ If the disc is poor in quality, or is dirty or damaged, writing or rewriting

errors may be noted - ensure that you check all discs for dirt or damage
before you use them.

■ The actual number of rewrites to CD-RW, DVD-RW, DVD+RW,

DVD-RAM or HD DVD-RW media will be affected by the quality of the
disc itself and the way in which it is used.

■ There are two types of DVD-R media available, authoring discs and

general use discs. Do not attempt to use authoring discs as only
general use discs can be written to by a computer drive.

■ You can use both DVD-RAM discs that can be removed from a cartridge

and DVD-RAM discs designed without a cartridge.

■ You may find that other computer DVD-ROM drives or other DVD

players may not be able to read DVD-R, DVD-R (Dual Layer), DVD-RW,
DVD+R, DVD+R (Double Layer), DVD+RW, HD DVD-R or HD DVD­R(Dual Layer) discs.

■ Data written to a CD-R, DVD-R, DVD-R (Dual Layer), DVD+R, DVD+R

(Double Layer), HD DVD-R or HD DVD-R(Dual Layer) discs cannot be
deleted either in whole or in part.

■ Data deleted/erased from a CD-RW, DVD-RW, DVD+RW, DVD-RAM or

HD DVD-RW disc cannot be recovered. You must check the content of
the disc carefully before you delete it, taking care that, if multiple drives
that can write data to discs are connected, you do not delete data from
the wrong one.

User’s Manual 4-22

Operating Basics

■ In writing to DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R

(Double Layer), DVD+RW, DVD-RAM, HD DVD-R, HD DVD-R(Dual
Layer) or HD DVD-RW media, some space is required for file
management, so you may not be able to write to the full capacity of the
disc.

■ Since the disc is based on the DVD standard, it might be filled with

dummy data if the written data is less than about 1 GB. Therefore,
in these circumstance, even if you write only a small amount of data,
it might take additional time to fill in the dummy data.

■ When multiple drives that can write data to discs are connected, be

sure that you do not write to or delete data from the wrong drive.

■ Be sure to connect the AC adaptor to the computer before you write

or rewrite any information.

■ Before you enter either Sleep Mode or Hibernation Mode, take care to

ensure that any DVD-RAM writing has been completed. In this instance,
writing is finished if you can eject the DVD-RAM media.

■ Be sure to close all other software programs except for the writing

software itself.

■ Do not run software such as a screen saver which can put a heavy load

on the processor.

■ Operate the computer at its full power settings - do not use any power-

saving features.

■ Do not write information while virus checking software is running,

instead wait for it to finish, then disable the virus protection applications,
including any software that checks files automatically in the
background.

■ Do not use any hard disk utilities, including those that are intended to

enhance hard disk drive access speeds, as they may cause unstable
operation and damage data.

■ CD-RW (Ultra Speed +) media should not be used as data may be lost

or damaged.

■ You should always write from the computer's hard disk drive onto the

CD/DVD/HD DVD - do not try to write from shared devices such as a
server or any other network device.

■ Writing with software other than TOSHIBA Disc Creator has not been

confirmed, therefore operation with other software applications cannot
be guaranteed.

When writing or rewriting

Please observe the following points while you write or rewrite data to CD-R,
CD-RW, DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R (Double
Layer), DVD+RW, DVD-RAM, HD DVD-R, HD DVD-R(Dual Layer) or
HD DVD-RW media:

■ Always copy data from the hard disk drive to the optical disc - do not

use the cut-and-paste function as the original data will be lost if there is
a write error.

User’s Manual 4-23

Operating Basics

■ Do not perform any of the following actions:

■ Change users in the Windows VistaTM operating system.

■ Operate the computer for any other function, including such tasks as

using a mouse or Touch Pad, or closing/opening the display panel.

■ Start a communication application such as a modem.

■ Apply impact or vibration to the computer.

■ Install, remove or connect external devices, including such items as

a ExpressCard, SD/SDHC memory card, ExpressCard, Memory
Stick/Memory Stick Pro, xD picture card, MultiMediaCard, USB
device, external monitor, i.LINK device, or an optical digital device.

■ Use the audio/video control button to reproduce music or voice.

■ Open the optical disc drive.

■ Do not use shut down, log off, Sleep Mode or Hibernation Mode

functions while writing or rewriting.

■ Make sure that the write/rewrite operation is completed before going

into either Sleep Mode or Hibernation Mode (writing is completed if you
can remove an optical disc on the HD DVD-R drive).

■ If the media is of poor quality, or is dirty or damaged, writing or rewriting

errors may occur.

■ Set the computer on a level surface and avoid places subject to

vibration such as airplanes, trains or cars. In addition, do not use the
computer on an unstable surface such as a stand.

■ Keep mobile phones and other wireless communication devices away

from the computer.

TOSHIBA Disc Creator

Note the following limitations when you use TOSHIBA Disc Creator:

■ DVD-Video cannot be created using TOSHIBA Disc Creator.

■ DVD-Audio cannot be created using TOSHIBA Disc Creator.

■ You cannot use TOSHIBA Disc Creator's "Audio CD for Car or Home

CD Player" function to record music to DVD-R, DVD-R (Dual
Layer),DVD-RW, DVD+R, DVD+R (Double Layer), DVD+RW,
HD DVD-R, HD DVD-R(Dual Layer) or HD DVD-RW media.

■ Do not use the "Disc Backup" function of TOSHIBA Disc Creator in

order to copy DVD Video, DVD-ROM, HD DVD Video or HD DVD-ROM
material that has copyright protection.

■ DVD-RAM discs cannot be backed up using the "Disc Backup"

functionof TOSHIBA Disc Creator.

■ You cannot back up CD-ROM, CD-R or CD-RW media to DVD-R,

DVD-R (Dual Layer), DVD-RW, HD DVD-R, HD DVD-R(Dual Layer) or
HD DVD-RW media using the 'Disc Backup' function of TOSHIBA Disc
Creator.

User’s Manual 4-24

Operating Basics

■ You cannot back up CD-ROM, CD-R or CD-RW media to DVD+R,

DVD+R (Double Layer) or DVD+RW media using the "Disc Backup"
function of TOSHIBA Disc Creator.

■ You cannot back up DVD-ROM, DVD Video, DVD-R, DVD-R (Dual

Layer), DVD-RW, DVD+R, DVD+R (Double Layer), DVD+RW,
HD DVD-ROM, HD DVD-R, HD DVD-R(Dual Layer) or HD DVD-RW to
CD-R or CD-RW media using the "Disc Backup" function of TOSHIBA
Disc Creator.

■ TOSHIBA Disc Creator cannot record in packet format.

■ You might not be able to use the "Disc Backup" function of TOSHIBA

Disc Creator to back up a DVD-R, DVD-R (Dual Layer), DVD-RW,
DVD+R, DVD+R (Double Layer), DVD+RW, HD DVD-R,
HD DVD-R(Dual Layer) or HD DVD-RW disc that was made with other
software on a different optical media recorder.

■ If you add data to a DVD-R, DVD-R (Dual Layer), DVD+R, DVD+R

(Double Layer), HD DVD-R or HD DVD-R(Dual Layer) disc that you
have already recorded to,you might not be able to read the added data
under some circumstances. For example, it cannot be read under 16-bit
operating systems, such as Windows 98SE and Windows Me, while in
Windows NT4 you will need Service Pack 6 or later, and in Windows
2000, you will need Service Pack 2. In addition to this, some DVD-ROM
and DVD-ROM/CD-R/RW drives cannot read this added data
regardless of the operating system.

■

TOSHIBA Disc Creator does not support recording to DVD-RAM discs ­to achieve this you should use Windows Explorer or another similar utility.

■ When you back up a DVD disc, be sure that the source drive supports

recording to DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R
(Double Layer) or DVD+RW media - if this is not the case then the
source disc might not be backed up correctly.

■ When you back up a DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R,

DVD+R (Double Layer), DVD+RW, HD DVD-R, HD DVD-R (Dual
Layer) or HD DVD-RW disc, be sure to use the same type of disc.

■ You cannot partially delete any data written to a CD-RW, DVD-RW,

DVD+RW, HD DVD-RW disc.

Data Verification

To verify that data has been written or rewritten correctly to a data
CD/DVD/HD DVD you should follow the steps below before you begin the
write/rewrite pro-cess:

1. Display the setting dialog box by one of the following two steps:

■ Click the Recording settings button( ) for writing on the main

toolbar in the Data Disc mode.

■ Select Setting for Each Mode  Data Disc in the Setting menu.

2. Mark the Verify written data check box.

3. Select File Open or Full Compare mode.

4. Click the OK button.

User’s Manual 4-25

How to learn more about TOSHIBA Disc Creator

Please refer to the Help files for additional TOSHIBA Disc Creator
information.

Video

You can record video using Ulead DVD MovieFactory® for TOSHIBA.

Using Ulead DVD MovieFactory® for TOSHIBA

How to make a Labelflash DVD

Simplified steps for making a Labelflash DVD:

1. Insert a Labelflash disc in DVD drive.

Set PRINTING SIDE for underside.

2. Click Start  All Programs  DVD MovieFactory for TOSHIBA 
Ulead DVD MovieFactory for TOSHIBA Laucher to lanuch DVD

MovieFactory.

3. Click Print Disc Label  Label Printing. Ulead Label@Once is
started.

4. Click the General tab.

5. Choose DVD Drive for Printer. e.g.<E:> PIONEER DVD....

6. Add and customize the look of your images and text.

7. Click Labelflash setting and choose Draw Quality.

8. Click Print.

Operating Basics

How to make a DVD-Video

Simplified steps for making a DVD-Video from video data captured from a
DV-Camcorder:

1. Click  All Programs  DVD MovieFactory for TOSHIBA 
Ulead DVD MovieFactory for TOSHIBA Launcher to launch DVD
MovieFactory.

2. Insert a DVD-RW or DVD+RW disc in Burner.

3. Click Video Disc  Burn Video to Disc to launch Direct Recording
dialog box, choose DVD-Video/+VR to invoke Straight Capture to
Disc Page.

4. Choose DVD-Video format.

5. Confirm the capture source is DV.

6. Press Capture button.

User’s Manual 4-26

Simplified steps for making a DVD-Video from adding video source:

1. Click  All Programs  DVD MovieFactory for TOSHIBA 
Ulead DVD MovieFactory for TOSHIBA Launcher to launch DVD
MovieFactory.

2. Click Video Disc  New Project to invoke 2
project type, then invoke MediaFactory.

3. Add source from HD Disk by click Add video files button to invoke
browser dialog box.

4. Choose the source video then go to Next page to apply Menu.

5. After choose the menu template, press Next button to go to Burning
Page.

6. Choose the output type then press Burn button.

nd

Launcher, choose your

How to learn more about Ulead DVD MovieFactory

Please refer to the Help and Manual files for additional Ulead DVD
MovieFactory information.

Important information for use

Note the following limitations when you write Video DVD:

1. Editing digital video

■ Log in with Administrator rights to use DVD MovieFactory.

■ Make sure that your computer is running on AC power when using

DVD MovieFactory.

■ Operate the computer at Full Power. Do not use power-saving

features.

■ While you are editing DVD, you can display preview. However,

if another application is running the preview might not display
properly.

■ DVD MovieFactory cannot edit or play copy protected content.

■ Do not enter sleep or hibernation mode while using DVD

MovieFactory.

■ Do not operate DVD MovieFactory immediately after turning on the

computer. Please wait until all Disc Drive activity has stopped.

■ When recording to a DV-Camcorder, to ensure you capture all of

your data, let the camcorder record for a few seconds before you
begin recording your actual data.

■ CD recorder, JPEG functions, DVD-Audio, mini DVD and Video CD

functions are not supported in this version.

■ While recording video to DVD, please close all other programs.

■ Do not run software like a screen saver because it can put a heavy

load on the CPU.

■ Do not support mp3 decode and encode.

Operating Basics

User’s Manual 4-27