You will find the model number and serial number on
the back of the TV. Record these numbers in the spaces
provided below. Refer to them whenever you call upon
your TOSHIBA dealer regarding this product.
• Thank you for purchasing this Toshiba LCD Color
Television. This manual will help you use the exciting
features of your new TV.
• Instructions in this manual are based on using the remote
control.
• You also can use the controls on the TV if they have the
same name as those referred to on the remote control.
• Please read all safety and operating instructions in this
manual carefully, and keep this manual for future reference.
Important Safety Instructions
Be sure to observe the following instructions and precautions
to ensure safe use of this TV.
Installation
1) Always connect the power plug to an appropriate
electrical outlet equipped with A model: 220-240V,
AC 50Hz, E model: 220-240V, AC 50/60Hz and T
model: 110-240V, AC 50/60Hz.
Never use the TV outside the specified voltage range. It
may cause a fire or an electric shock.
Ex. 220-240V AC, 50/60Hz
3) Never place the TV in an unstabilized location such
as on a shaky table, incline or location subject to
vibration.
The TV may drop or fall off which may cause an injury
or damage.
4) Never block or cover the slots and openings in the
cabinet.
• Never place the TV so that it is facing upward or on
its side.
• Never place the TV in a closet, bookcase or other
similar area where the ventilation is poor.
• Never drape a newspaper, tablecloth or curtain on the
TV.
• When installing the TV against a wall, always keep
the TV at least 10 cm away from the wall.
• Never place the TV on a soft unstable surface, such
as a carpet, or a cushion.
The inside of this TV will overheat if the ventilation holes
are covered, blocked or sealed, which may result in a
fire.
Check!
WARNING ABOUT THREE-WIRE GROUNDINGTYPE PLUG: (For E model only)
• This product shall be connected to a main socket
outlet with a protective earthing connection.
• Never remove the earthing pin on the power plug.
This system is equipped with a three pin earthingtype power plug. This plug will only fit an earthingtype power outlet. This is a safety feature. If you are
unable to insert the plug into the outlet, contact an
electrician to replace the wall outlet.
• Never defeat the purpose of the earthing plug.
About the fuse
In a three pin earthing-type, the fuse fitted in this plug is
approved by ASTA or BSI to BS1362. It should only be
replaced by a correctly rated and approved type and the
fuse cover must be refitted.
2) Never insert or remove the power plug with wet
hands.
This may cause an electric shock.
5) Never place the TV near a heater or in direct
sunlight.
The surface of the cabinet or power cord may melt and
result in a fire or an electric shock.
6) Never place the TV in an area exposed to high
humidity levels, such as in a bathroom or close to a
humidifier.
This may cause a fire or an electric shock.
3
Introduction
S
7) Never place the TV next to a stove where it will be
exposed to oil, smoke, or steam, or in a location
where there is a large quantity of dust.
This may cause a fire or an electric shock.
8) Install the TV in a horizontal, stable location.
Connect between two clips on the back of the TV
and a wall, pillar, etc., with a sturdy tie and clip of
supplied accessories (- page 36).
• Use as short a tie as possible to ensure the TV is
stable.
• If the TV is not installed securely, it may lean or fall
over and cause an injury.
• To prevent injury, use the exclusive optional stand or
wall-hanging bracket to install this TV on the floor or
wall securely in accordance with a qualified
technician.
10cm min.
turdy tie
(as short as possible)
10) Precautions for installing on outdoor antenna
An outside antenna system should not be located in the
vicinity of overhead power lines, or other electric light or
power circuits.
If the antenna falls down or drops, it may cause an injury
or an electric shock.
Use
1) Never place hot objects or open flame sources,
such as lighted candles or nightlights, on or close
to the TV.
High temperatures can melt plastic and lead to fires.
Clip
Side view op view
Clip
T
9) Precautions for moving the TV
• When moving the TV, be sure to remove the plug
from the wall outlet and disconnect the antenna cable
and audio/video cables, any steady ties. A fire or an
electric shock may result if the power cord is
damaged.
• When carrying the TV, at least two people are
needed. Be sure to carry it upright.
• Never carry the TV with the screen facing up or down.
Clip
2) The apparatus shall not be exposed to dripping or
splashing and that no objects filled with liquids,
such as vases, shall be placed on the apparatus.
When liquids are spilled or small items are dropped
inside the TV, this may cause a fire or an electric shock.
If small objects drop inside the TV, turn off the TV and
remove the power plug from the outlet immediately and
contact a service technician.
3) Never insert objects (metal or paper) or pour water
inside the TV through ventilation holes and other
openings.
These items may cause a fire or an electric shock.
If these objects are inserted inside the TV, turn off the
TV and remove the power plug from the outlet
immediately and contact a service technician. Be
especially careful that children do not insert objects in
the TV.
Clip
4
Introduction
4) Never stand or climb on the TV.
Be especially careful in households with children to
prevent them through climbing on top of the TV.
It may move, fall over, break, become damaged or
cause an injury.
5) When the TV will not be used for a long period of
time, such as during vacation or travel, remove the
power plug from the wall outlet for safety.
• The TV is not completely disconnected from the
power supply line, as minute current is consumed
even when the ! Power switch is turned off.
• The Mains plug or an appliance coupler is used as the
disconnect device, therefore the disconnect device
shall remain readily operable.
6) Never pull on the power cord when removing the
plug from the wall outlet.
Always hold the plug firmly when removing it. If the
power cord is yanked, the cord may become damaged
and a fire or an electric shock may occur.
8) If there is thunder or lightning, never touch the
antenna cable or other connected cables.
You may suffer an electric shock.
Service
1) Never repair, modify or disassemble the TV by
yourself.
It may cause a fire or an electric shock. Consult a
service technician for inspection and repairs.
2) When a malfunction occurs, or if smoke or an
unusual odor comes from the TV, turn off the TV
and remove the power plug from the outlet
immediately.
Make sure that the smoke or smell has stopped, then
contact a service technician. If the TV is still used in this
condition, it may cause a fire or an electric shock.
7) Never cut, break, modify, twist, bunch up or bent the
cord or apply excessive force or tension to it.
Never place heavy objects on the cord or allow it to
overheat as this may cause damage, a fire or an electric
shock. Contact a service technician if the power cord is
damaged.
3) If the TV is dropped or the cabinet is broken, turn off
the TV and remove the power plug from the outlet
immediately.
If the TV is still power used in this condition, it may
cause a fire or an electric shock. If the cabinet is broken,
be careful when handling the TV to prevent an injury.
Contact a service technician for inspection and repair.
5
Introduction
4) When the TV reaches the end of its useful life, ask a
qualified service technician to properly dispose of
the TV.
Note:
The lamp unit contains a small amount of mercury.
Disposal of mercury may be regulated due to
environmental considerations.
Dispose of the used lamp unit by the approved method
for your area. For disposal or recycling information,
please contact your local authorities.
Cleaning
1) Remove the power plug before cleaning.
Never use solvents such as benzine or thinner to clean
the TV.
• These solvents may distort the cabinet or damage its
finish.
• If rubber or vinyl products remain in contact with the
TV for a long time, a stain may result.
If the cabinet becomes dirty, clean it with a soft, dry
cloth.
When cleaning the surface of the LCD display, wipe the
panel surface gently with a soft, dry cloth.
Important information
1) About LCD screen
• If you have the LCD screen facing to the sun, the LCD
screen will be damaged. Be aware of locating the TV
in the place such as window side or outside of the
room.
• Never press the LCD screen strongly or scratch it,
and never put anything on it. These actions will
damage the LCD screen.
2) About cabinet and LCD screen
Never spray volatile compounds such as insecticide on
the cabinet and LCD screen.
This may cause a discoloration or damage the cabinet
and LCD screen.
3) Some pixels of the screen do not light up
The LCD display panel is manufactured using an
extremely high level of precision technology, however
sometimes some pixels of the screen may be missing
picture elements or have luminous spots. This is not a
sign of a malfunction.
4) About Interference
The LCD display may cause interference in image,
sound, etc. of other electronic equipment that receives
electromagnetic waves (e.g. AM radios and video
equipment).
5) About using under the low temperature places
If you use the TV in the room of 0°C or less, the picture
brightness may vary until the LCD monitor warms up.
This is not a sign of a malfunction.
2) Periodically disconnect the power plug from the
outlet and check it.
If dust has collected on the power plug connectors,
clean off the dust with a dry cloth.
This dust may cause a fire due to reduced insulation on
the plug.
Clean here
6) About afterimage
If a still picture is displayed, an afterimage may remain
on the screen, however it will disappear.
This is not a sign of malfunction.
Exemptions
• Toshiba is not liable for any damage caused by fires, natural
disaster (such as thunder, earthquake, etc.), acts by third
parties, accidents, owner’s misuse, or uses in other improper
conditions.
• Toshiba is not liable for incidental damages (such as profit
loss or interruption in business, modification or erasure of
record data, etc.) caused by use or inability to use of product.
• Toshiba is not liable for any damage caused by neglect of
the instructions described in the owner’s manual.
• Toshiba is not liable for any damage caused by misuse or
malfunction through simultaneous use of this product and
the connected equipment.
6
Getting started
Connecting an antenna
Optimum reception of color requires a good signal and will
generally mean that an outdoor antenna must be used.
The exact type and positioning of the antenna will depend upon
your particular area.
Your Toshiba dealer or service personnel can best advise you
on which antenna to use in your area.
Before connecting the antenna cable, turn off all main power
switches.
VHF and/or
UHF antenna
Media Recorder
IN
OUT
Antenna cable (75 7 coaxial)
(not supplied)
300 7 twin-lead feeder
TV back view
Exploring your new TV
Installing the remote control batteries
Remove the battery cover.
Insert two R03 (AAA) batteries matching the –/+ polarities of
the battery to the –/+ marks inside the battery compartment.
Cautions:
• Dispose of batteries in a designated disposal area. Never
throw batteries into a fire.
• Attention should be drawn to the environmental aspects of
battery disposal.
• Never mix battery types or combine used batteries with new
ones.
Notes:
• If the remote control does not operate correctly, or if the
operating range becomes reduced, replace both batteries
with new ones.
• If the batteries are dead or if you will not use the remote
control for a long time, remove the batteries to prevent
battery acid from leaking into the battery compartment.
Antenna adaptor
(not supplied)
75 7 coaxial cable
Plug
(not supplied)
75 7
antenna
terminal
75 7 antenna
terminal
Effective range
within 5 m
7
Getting started
TV front and side panel controls
• You can operate your TV using the buttons on the side panel or the remote control. The back and side of the panel provide the
terminal connections to connect other equipment to your TV (- “Connecting your TV” pages 28 - 32).
• For the use of each control, see the pages in brackets.
Right side view TV front view Control panel
4
5
6
7
8
9
10
1 3 2
Headphones
(Not supplied)
11
14 (Timer LED) — Timer indicator (- page 20).
2! (Power LED) — Power indicator (- page 11).
3(Remote sensor) — Point the remote control toward
this remote sensor (- page 7).
4! (Power on/Standby) — Press to turn the TV on/
standby (-page 11).
5pBb(Program position) — When no menu is on-
screen, these buttons select the program position.
(- page 13).
Uu(MENU up/down) — When a menu is on-screen,
these buttons function as up/down menu navigation
buttons (- page 11).
62 – + (Volume) — When no menu is on-screen, these
buttons adjust the volume level (- page 10).
I i(MENU left/right) — When a menu is on-screen,
these buttons function as left/right menu navigation
buttons or adjust settings (- page 11).
7MENU — Press to access the menu system (- page 11).
8o (Input source selection) — When no menu is on-
screen, this button selects the input source (- page 21).
OK — When a menu is on-screen, this button functions
as the next menu navigation button (- page 11, 21).
9o HDMI3 (input terminal) —High-Definition
Multimedia Interface input receives digital audio and
uncompressed digital video from an HDMI device
(- page 29).
10 o (2) (Video 2 input terminals) — Optional S-video
or standard video and standard audio inputs (- page 28).
11 D (Headphone jack) — For use with headphones (-
page 27).
8
TV back panel connections
12
13
15 16
Getting started
TV back view
* You can use the cable
holder to hold antenna
cable, video and audio
cables etc.
When moving the TV,
never hold this holder.
14
17
18
19 20 21 22
12 o (C1) (COMPONENT VIDEO INPUT terminals)
—High-definition component video and standard audio
inputs (- page 28).
13 o PC/HDMI1 (AUDIO) (input terminals) — PC
audio input terminals are shared with HDMI1 analog
audio input terminals, and their use can be configured in
the SET UP menu. (- page 29, 32).
14 o (C2) (COMPONENT VIDEO INPUT terminals)
— High-definition component video and standard audio
inputs (- page 28).
15 o (1) (Video 1 input terminals) — Optional S-video
or standard (composite) video and standard (analog)
stereo audio inputs (- page 28).
16 O WOOFER (VARIABLE) (output terminal) — For
use when connecting woofer system (variable) (- page
28).
17 O AUDIO (FIXED/VARIABLE) (output terminals)
— Standard audio outputs (fixed/variable) (- page 28).
Power cord
Cable holder*
18 O MONITOR (output terminals) — Standard video
and standard audio outputs (- page 28).
19 A (Antenna input terminal) — Analog antenna signal
input (- page 7).
20 o RGB/PC (input terminal) — For use when
connecting a personal computer (PC) (- page 32).
21 o HDMI1 (input terminal) — High-Definition
Multimedia Interface input receives digital audio and
uncompressed digital video from an HDMI device or
uncompressed digital video from a DVI device (- page
29).
22 o HDMI2 (input terminal) — High-Definition
Multimedia Interface input receives digital audio and
uncompressed digital video from an HDMI device
(- page 29).
9
Getting started
Learning about the remote control
Location of controls
To select device mode (T/R/D)*
*
T: TV mode
R:
REGZA-LINK mode
D: DVD mode
Number buttons (0-9)
(- pages 12, 20)(T/R/D)
To return to the previous program (T)
(
-
page 12)
Volume – + (T/R/D)
(These buttons adjust the volume level.)
TOP MENU To access top Menu (R/D)
-
• Menu (T/R/D)(
• OK (T/R/D)(
-
page 11, 21)
page 11)
• MENU (T)
• DVD Menu (R/D)
• Teletext control buttons (T)(
-
page 24)
• To work interactive service control
on device (R)
Picture mode selection (T/R/D)
(
-
page 15)
Picture size selection (T/R/D)
(
-
page 14)
REGZE-LINK or D VD mode :
p r ess to EJECT
p r ess to STOP
p r ess to PL A Y
p r ess to P AUSE/STEP
p r ess to SKIP REVERSE
p r ess to FAST REVERSE
p r ess to FAST FORWARD
p r ess to SKIP FO R W ARD
selection (- page 18)
Pictu r e still ( - page 15)
T o r eveal concealed text
(- page 25)
T o hold a wanted page
(- page 25)
T o enlarge teletext display size
(- page 25)
To access sub-pages
(- page 24)
• T o select a page while viewing
a no r mal pictu r e
(- page 25)
• T o select the time display
(- page 25)
REGZA-LINK mode switch on the TV remote control allows the control of connected REGZA-LINK device being watched
(- page 22, 23).
Note:
These functions are dependent on the connected device. Not all the remote control buttons may be available. Please refer to the
owner’s manual for all the connected devices.
10
Getting started
Turning the TV on
Switching on the TV
Connect the power cord to a wall outlet, the ! power
indicator lights in red (standby mode).
1Press 1 on the remote control or ! on the TV right side
panel. The ! power indicator lights in green.
Note:
If you watch black and white programs when the color system
mode is set to Auto, color noise may appear on the screen. In
this case select the appropriate Color system (For the system
of each country or region, refer to pages 13 and 35).
Switching off the TV
1
Press 1 on the remote control or ! on the TV right side
panel to switch to the standby mode.
Notes:
• When the TV will not be used for a long period of time, such
as during vacation or travel, remove the power plug from the
wall outlet.
• The TV will automatically turn itself off after approximately 15
minutes if it is tuned to a vacant channel or a station that
completes its broadcast for the day. This function does not
work in external input or Blue screen Off mode.
The TV will automatically turn itself off after approximately 2
hours if you do not operate the TV after turned on by on timer
function.
• If power is cut off while you are viewing the TV, the Last
Mode Memory function turns on the TV automatically when
power is applied again. If power is going to be off for a long
time and you are going to be away from your TV, unplug the
power cord to prevent the TV from turning on in your
absence.
Displaying the menu chart
PICTURE
menu
Picture settings
Active Backlight Control
Cinema mode
Film Stabilization
meta brain PRO 100
xvYCC selection xvYCC selection
MENU
PICTURE
EXIT
Back Watch TV
1/2
OK
On
On Off
Off
On
SOUND
menu
MTS
Dual
Headphone
Headphone level
Bass
Tre bl e
MENU
SOUND 1/ 2
EXIT
Back Watch TV
Auto
Dual 1
Mode 1
0
0
SET UP
menu
Language
Auto tuning
Manual tuning
AV connection
Picture position
MENU
SET UP
EXIT
Back Watch TV
English
OK
OK
OK
OK
REGZA-LINK
menu
Enable REGZA-LINK
TV Auto Input Switch
TV Auto Power
Auto Standby
Speaker Preference
MENU
REGZA-LINK
EXIT
Back Watch TV
On
On
On
On
TV Speakers
3D Color management
Base color adjustment
Picture settings
Active Backlight Control
Cinema mode
Film Stabilization
meta brain PRO 100
Auto tuning
Manual tuning
AV connection
Picture position
MENU
Back Watch TV
Enable REGZA-LINK
TV Auto Input Switch
TV Auto Power
Auto Standby
Speaker Preference
MENU
Back Watch TV
PICTURE 2/ 2
PICTURE
EXIT
SOUND 2/ 2
SOUND
EXIT
SET UP
EXIT
REGZA-LINK
EXIT
On
OK
OK
Off
On
On
0
OK
Off
On
On 70
Auto
Dual 1
Mode 1
0
0
English
OK
OK
OK
OK
On
On
On
On
TV Speakers
1/2
1/2
Learning about the menu system
We suggest you familiarize yourself with the display charts
before using the menu system:
•Press M to display menu, then press or to select main
menu headings.
•Press or to select an item.
•Press or to select or adjust setting.
• Press Q to display the next menu.
•Press P, to close the menu display instantly.
•Press M, to return the previous menu.
• The menu display will disappear automatically, if you do
not make a selection for a while.
Note:
Depending on the input signal, selecting function or settings,
the items in the menu display may be different or unable to be
selected. Please refer to individual functional explanation.
TIMER
menu
Sleep timer
On timer
On timer Position
MENU
EXIT
Back Watch TV
FUNCTION
menu
Teletext
Teletext language
Auto format
Blue screen
Side panel
MENU
FUNCTION
EXIT
Back Watch TV
TIMER
00:00
00:00
01
Auto
1
On
On
1
Sleep timer
On timer
On timer Position
MENU
Teletext
Teletext language
Auto for mat
Blue screen
Side panel
MENU
TIMER
EXIT
Back Watch TV
FUNCTION
EXIT
Back Watch TV
00:00
00:00
01
Auto
1
On
On
1
11
Loading...
+ 25 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.