TOSHIBA 42HDX82, 50HDX82, 57HDX82, 65HDX82 User guide

Introduction

Connecting

your TV

WNER'S

ANUAL

Projection Television

Remote Control

Using the

Setting up

your TV

Using the TV’s

Features

42HDX82 50HDX82 57HDX82 65HDX82

Appendix

Owner's Record

The model number and serial number are on the back of your TV. Record these numbers in the spaces below. Refer to these numbers whenever you communicate

Index

with your Toshiba dealer about this TV.

Model number:

Serial number:

23565682A

Dear Customer,

Thank you for purchasing this Toshiba TV. This manual will help you use the many exciting features of your new TV.

Before operating the TV, please read this manual completely, and keep it nearby for future reference.

Child Safety

It Makes A Difference Where Your TV Stands

Safety Precautions

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning symbol in the triangle tells you that the voltage inside this product may be strong enough to cause an electric shock. DO NOT TRY TO SERVICE THIS PRODUCT YOURSELF.

The exclamation mark in the triangle tells you that important operating and maintenance instructions follow this symbol.

NOTE TO CATV INSTALLERS IN THE USA

This is a reminder to call the CATV system installer’s attention to Article 820-40 of the NEC, which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. For additional antenna grounding information, see items 24 and 25 on page 4.

NOTICE OF POSSIBLE TV STAND INSTABILITY

DANG ER: R ISK OF SERIOUS PERSONAL INJURY OR DEATH!

the TOSHIBA TV stand recommended in the “Specifications” section only. result in instability, causing possible injury or death.

NOTICE OF POSSIBLE ADVERSE EFFECTS

ON TV PICTURE TUBE

If a fixed (non-moving) pattern remains on the TV screen for long periods of time, the image can become permanently engrained in the picture tube. This type of

damage is NOT COVERED BY YOUR WARRANTY.

See item 32 on page 4.

Use this TV with

Use with other stands may

Congratulations on your purchase! As you enjoy your new TV, keep these safety tips in mind:

The Issue

 If you are like most Americans, you have a TV in your home.

Many homes, in fact, have more than one TV.

 The home theater entertainment experience is a growing

trend, and larger TVs are popular purchases; however, they are not always supported on the proper TV stands.

 Sometimes TVs are improperly secured or inappropriately

situated on dressers, bookcases, shelves, desks, audio speakers, chests, or carts. As a result, TVs may fall over, causing unnecessary injury.

Toshiba Cares!

 The consumer electronics industry

is committed to making home

entertainment enjoyable and safe.

 The Consumer Electronics

Association formed the Home

Entertainment Support Safety

Committee, comprised of TV and consumer electronics furniture

manufacturers, to advocate

children’s safety and educate

consumers and their families about

television safety.

Tune Into Safety

 One size does NOT fit all! Use appropriate

furniture large enough to support the weight of your

TV (and other electronic components).

 Use appropriate angle braces, straps, and anchors to secure

your furniture to the wall (but never screw anything directly into the TV).

 Carefully read and understand the other enclosed

instructions for proper use of this product.

 Do not allow children to climb on or play with furniture

and TVs.

 Avoid placing any item on top of your TV (such as a VCR,

remote control, or toy) that a curious child may reach for.

 Remember that children can become excited while watching

a program and can potentially push or pull a TV over.

 Share our safety message about this hidden hazard of

home with your family and friends. Thank you!

2500 Wilson Blvd. Arlington, VA 22201 U.S.A. Tel. 703-907-7600 Fax 703-907-7690 www.CE.org

CEA is the Sponsor, Producer and

05/02.2

Manager of the International CES

the

Important Safety Instructions

QUALIFIED

SERVICE

TECHNICIAN

Installation, Care, and Service

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near

water.

6) Clean only with a dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

CAUTION: To reduce the risk of electric shock, do not use the polarized plug with an extension cord, receptacle, or other outlet unless the blades can be inserted completely to prevent blade exposure.

Wide plug

Installation

Follow these recommendations and precautions and heed all warnings when installing your TV:

15) Never modify this equipment. Changes or modifications may void: a) the warranty, and b) the user’s authority to operate this equipment under the rules of the Federal Communications Commission.

16) DANG ER: RISK OF SERIOUS PERSONAL

INJURY, DEATH, OR EQUIPMENT DAMAGE! Never place the TV on

an unstable cart, stand, or table. The TV may fall, causing serious personal injury, death, or serious damage to the TV.

17) Never place or store the TV in direct sunlight; hot, humid areas; areas subject to excessive dust or vibration; or locations with temperatures at or below 41°F (5°C).

18) Always place the TV on the floor or a sturdy, level, stable surface that can support the weight of the unit.

19) Never place items such as vases, aquariums, or candles on top of the TV.

10) Protect the power cord from being

walked on or pinched, particularly at plugs, convenience receptacles, and the point where it exits the apparatus.

11) Only use attachments/accessories specified by the

manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use

caution when moving the cart/apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during

lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

20) Never block or cover the slots or openings in the TV cabinet back, bottom, and sides. Never place the TV:

• on a bed, sofa, rug, or similar

surface;

• too close to drapes, curtains,

or walls; or

• in a confined space such as a

bookcase, built-in cabinet, or any other place with poor ventilation.

The slots and openings are provided to protect the TV from overheating and to help maintain reliable operation of the TV.

21) Never allow anything to rest on or roll over the power cord, and never place the TV where the power cord is subject to wear or abuse.

22) Never overload wall outlets and extension cords.

05/02.2

Ground clamp

Antenna discharge unit (NEC Section 810-20)

Grounding conductors (NEC Section 810-21)

Power service grounding electrode system (NEC Art 250 Part H)

Ground clamps

Antenna lead-in wire

Electric service equipment

QUALIFIED

SERVICE

TECHNICIAN

23) Always operate this equipment from a 120 VAC, 60 Hz power source only.

29) [This item applies to projection TVs only.] If the air temperature rises suddenly (for example, when the TV is first delivered), condensation may form on the lenses. This can make the picture appear distorted or the color appear faded. If this happens, turn off the TV for 6 to 7 hours to allow the condensation to evaporate.

24) Always make sure the antenna system is properly grounded to provide adequate protection against voltage surges and built-up static charges (see Section 810 of the National Electric Code).

25) DANGER: RISK OF SERIOUS PERSONAL

INJURY OR DEATH!

• Use extreme care to make sure you are never in

a position where your body (or any item you are in contact with, such as a ladder or screwdriver) can accidentally touch overhead power lines. Never locate the antenna near overhead power lines or other electrical circuits.

• Never attempt to install any of the following during lightning activity: a) an antenna system; or b) cables, wires, or any home theater component connected to an antenna or phone system.

30)For added protection of your TV from lightning and power surges, always unplug the power cord and disconnect the antenna from the TV if you leave the TV unattended or unused for long periods of time.

31) During normal use, the TV may make occasional snapping or popping sounds. This is normal, especially when the unit is being turned on or off. If these sounds become frequent or continuous, unplug the power cord and contact a Toshiba Authorized Service Center.

32) Possible Adverse Effects on TV Picture Tube: If a fixed (non-moving) pattern remains on the TV screen for long periods of time, the image can become permanently engrained in the picture tube and cause subtle but permanent ghost images. This type of damage is NOT COVERED BY YOUR WARRANTY. Never leave your TV on for long periods of time while it is displaying the following formats or images:

• Fixed Images, such as PIP/POP windows, stock tickers,

video game patterns, TV station logos, and websites.

• Special Formats that do not use the entire screen. For

example, viewing letterbox style (16:9) media on a normal (4:3) display (gray bars at top and bottom of screen); or viewing normal style (4:3) media on a widescreen (16:9) display (gray bars on left and right sides of screen).

Care

For better performance and safer operation of your TOSHIBA TV, follow these recommendations and precautions:

26) Always sit approximately 10–25 feet away from the TV and as directly in front of it as possible. The picture can appear dull if you sit too far to the left or right of the TV, or if sunlight or room lights reflect on the screen. Turn the TV off to check for reflections on the screen, and then remove the source of reflections while viewing the TV.

27) Always unplug the TV before cleaning. Never use liquid or aerosol cleaners.

28) WARNI NG: RISK OF ELECTRIC SHOCK!

Never spill liquids or push objects of any kind into the TV cabinet slots.

Service

33) WARNI NG: RISK OF ELECTRIC SHOCK! Never attempt to service the

TV yourself. Opening and

removing the covers may expose you to dangerous voltage or other hazards. Refer all servicing to a Toshiba Authorized Service Center.

34) If you have the TV serviced:

• Ask the service technician to use only replacement parts

specified by the manufacturer.

• Upon completion of service, ask

the service technician to perform routine safety checks to determine that the TV is in safe operating condition.

35) When the TV reaches the end of its useful life, ask a

qualified service technician to properly dispose of the TV. Improper disposal may result in a picture tube implosion

05/02.2

and possible personal injury.

Important safety information.............................. 2–5

Introduction................................................................ 7

Welcome to Toshiba ......................................................... 7

Exploring your new TV ................................................... 7

Note regarding Quick Connect Guide .......................... 7

Connecting your TV .................................................. 8

Note regarding picture quality ......................................... 8

Connecting a VCR .......................................................... 8

Connecting a cable converter box .................................... 9

Connecting a cable converter box and VCR..................... 9

Connecting a DVD player or satellite receiver

and a VCR ..................................................................... 10

Connecting a DVD player with ColorStream

(component video) and a VCR ...................................... 11

Connecting a DTV receiver/set-top box with

ColorStream® (component video) and a VCR ................ 12

Connecting two VCRs ................................................... 13

Connecting a camcorder ................................................ 13

Connecting a device to the DVI/HDCP input .............. 14

Connecting a device to the IR blaster ............................. 15

Connecting an audio system .......................................... 16

Connecting an A/V receiver ........................................... 16

Using the remote control ...................................... 17

Preparing the remote control for use .............................. 17

Installing the remote control batteries ............................ 17

Remote Control functional key chart ...................... 18

Programming the remote control for use with your

audio/video devices ........................................................ 20

Device code setup ................................................... 20

Searching and sampling the code of a

device (8500) .......................................................... 20

Using the volume lock feature (8000) ..................... 21

Operational feature reset (8900) ............................. 21

Device code table .............................................. 22–23

Learning about the remote control ................................. 24

Setting up your TV .................................................. 25

Note regarding Quick Connect Guide ........................... 25

Learning about the menu system ................................... 25

Using the Quick Connect Guide ................................. 26

Changing the on-screen display language ....................... 27

Selecting the antenna input ............................................ 27

Adding channels to the TV’s memory ............................ 28

Programming channels automatically ...................... 28

Adding and erasing channels manually.................... 29

Changing channels ........................................................ 29

Changing channels using SpeedSurf........................ 29

Adjusting the color convergence..................................... 30

Automatically adjusting the color convergence using TouchFocus

™

................................................. 30

Manually adjusting the color convergence............... 30

Using the TV’s features.......................................... 32

Adjusting the channel settings ........................................ 32

Switching between two channels using Channel

Return .................................................................... 32

Switching between two channels using SurfLock

Programming your favorite channels ....................... 32

Labeling channels ................................................... 33

Viewing the wide-screen picture formats ........................ 35

Selecting the picture size ......................................... 35

™

.............................................................. 32

Scrolling the Theater Wide picture

(Theater Wide 2 and 3 only) .................................. 37

Selecting the cinema mode ...................................... 37

Using the POP double-window feature .......................... 38

Switching the main and POP pictures..................... 39

Freezing the POP picture ........................................ 39

Using the favorite channel search function .............. 39

Using the LOCKS menu ............................................... 40

Entering the PIN code ............................................ 40

If you cannot remember your PIN code .................. 40

Using the V-CHIP menu ............................................... 41

ENABLE BLOCKING .......................................... 41

TV RATING (Independent rating system for

broadcasters) ........................................................... 41

MPAA RATING (Independent rating system for

movies) ................................................................... 42

BLOCKING OPTION .......................................... 42

Unlocking programs temporarily ............................ 43

Locking channels ........................................................... 43

Locking video inputs ..................................................... 44

Using the front panel lock feature .................................. 45

Changing the PIN code ................................................. 45

Adjusting the picture ..................................................... 46

Selecting the picture mode ...................................... 46

Adjusting the picture quality ................................... 46

Saving your new preferences ................................... 47

Using the ALS (Automatic Light Sensor) feature..... 47

Using the flesh tone feature..................................... 47

Using CableClear

™

DNR (digital noise reduction) .... 48

Selecting the scan velocity modulation (SVM) .......... 48

Selecting the color temperature ............................... 49

Resetting your picture adjustments ......................... 49

Selecting the video input source ..................................... 50

Labeling the video input sources .................................... 50

Using the closed caption feature..................................... 51

Setting the sleep timer.................................................... 52

Setting the clock ............................................................ 52

Adjusting the sound ....................................................... 53

Muting the sound ................................................... 53

Selecting stereo/SAP broadcasts .............................. 53

Using the WOW

™

surround sound feature ............. 54

Adjusting the sound quality .................................... 54

Resetting your audio adjustments ........................... 55

Using the sub-bass system (SBS) ............................. 55

Turning off the built-in speakers ............................. 56

Selecting the Audio OUT sound ............................. 56

Using the StableSound

feature .............................. 57

Selecting the background of the menu display ............... 57

Displaying on-screen information .................................. 57

Viewing the demonstration mode .................................. 58

Understanding the auto power off feature ...................... 58

Understanding the last mode memory feature ................ 58

Appendix ................................................................... 59

Specifications ................................................................. 59

Tr oubleshooting ............................................................. 60

Limited United States Warranty ..................................... 61

Limited Canada Warranty.............................................. 62

Index .......................................................................... 63

Introduction

Welcome to Toshiba

Congratulations! You have purchased one of the finest projection TVs on the market. The goal of this manual is to guide you through setting up and operating your Toshiba TV as quickly as possible.

This manual applies to models 42HDX82, 50HDX82, 57HDX82, and 65HDX82. Before you start reading, check the model number on the back of your TV. Write your model and serial numbers in the space provided on the front cover of this manual for your records.

Instructions in this manual are based on using the remote control. You also can use the controls on the TV if they have the same name as those on the remote control.

Please read all the safety and operating instructions carefully, and keep this manual for future reference.

Exploring your new TV

You can operate your TV using the buttons on the front panel or the remote control. The back panel and front panel (behind the door) provide all the terminal connections you will need to connect other equipment to your TV. See “Connecting your TV” on page 8.

Note Regarding

Quick Connect Guide

The Quick Connect Guide automatically appears on-screen the first time the TV is turned on. This feature provides on-screen instructions to guide you through the initial setup of your TV.

To stop the Quick Connect Guide, either press EXIT or turn off the TV.

See page 26 for details.

Connecting

your TV

Remote Control

Using the

Front

Back

Remote control sensor

(Behind the screen)

Behind the door

VIDEO-3 IN

S-VIDEO

VIDEO

AUDIO

L/MONO R

Video 3

Video/audio inputs

S-VIDEO

VIDEO

MONO

AUDIO

VIDEO-1 VIDEO-2

Menu x •zy

CHANNELVOLUME

EXITMENU

Volume x • POWER

EXIT

TV/VIDEO

TouchFocus™

ALS (Automatic Light Sensor

OUCH

TV/VIDEO

OCUS

Channel zy

VIDEO

MONO

AUDIO

CENTER

CHANNEL IN

ON OFF

DVI/HDCP

COLOR STREAM HD 2

ININ

IR BLASTER

OUT

VAR. AUDIO

COLOR STREAM

HD 1

AUDIO

OUT

Power indicator

AUDIO

POWER

DVI/ HDCP

ANT( 75

ANT-1

OUT

ANT-2

Setting up

your TV

Using the TV’s

Features

CT-90121

Appendix

)

Index

Connecting your TV

Note: One IR blaster cable is provided with your TV. No other cables are provided.

Introduction

your TV

Connecting

Using the

Remote Control



 



When connecting video equipment to your Toshiba TV:

 



Coaxial cable is the cable that comes in from your antenna, cable TV service, or cable converter box. Coaxial cable has “F” connectors.

Standard stereo A/V cables usually come in sets of three, and are typically color-coded according to use: yellow for video, red for stereo right audio, and white for stereo left (or mono) audio. Your TV’s standard A/V inputs are color-coded in the same manner as the cables.

S-video cable is for use with video equipment that has an S-Video connector. Component video cables come in sets of three (typically color-coded red, green, and

blue), and are for use with video equipment that has component video connectors. Your TV’s ColorStream

(component video) inputs are color-coded in the same manner as the

cables. DVI-D digital single-link cable is for use with video equipment that has a DVI-D digital

single-link connector (see page 14).

NOTE REGARDING PICTURE QUALITY

For GOOD picture quality: Use a standard stereo A/V yellow video cable. For BETTER picture quality: If your equipment has an S-video connector, use an

S-video cable instead of a standard yellow video cable. (You still must connect the standard red and white audio cables for full system connection, but do not connect a standard yellow video cable at the same time or the picture performance will be unacceptable.)

For BEST picture quality: If your equipment has component video connectors, use component video cables instead of a standard yellow video cable or an S-video cable (plus the standard red and white audio cables for full system connection.) If your equipment has a DVI-D digital single-link connector, use a DVI-D cable (plus standard red and white audio cables connected to ”DVI/HDCP IN” for full system connection).

IR blaster cable is used to remotely control other A/V equipment (equipped with an an infrared sensor) through the TV (see page 15).

CAUTION: Do not plug in any power cords until you have finished connecting all equipment.

Coaxial (antenna) cable

Standard stereo A/V cables (typically color-coded yellow for video, red and white for audio)

S-video cable

Component video cables (typically color-coded red, green, blue)

DVI-D digital single-link cable

IR blaster cable

your TV

Setting up

Features

Using the TV’s

Appendix

Index

Connecting a VCR

This connection allows you to watch local channels and video programs, play or record on the VCR while watching TV, and record one channel while watching another channel.

You will need:

• two coaxial cables

• one set of standard A/V cables

From Cable Box or Antenna

Stereo VCR

VIDEO AUDIO

S-VIDEO

VIDEO

MONO

AUDIO

VIDEO-1 VIDEO-2

OUT

IR BLASTER

OUT

VAR. AUDIO

COLOR STREAM

AUDIO

HD 1

AUDIO

OUT

VIDEO

MONO

OUT to TV

AUDIO

CENTER

CHANNEL IN

ON OFF

DVI/HDCP

AUDIO

COLOR STREAM HD 2

ININ

ANT-1

OUT

ANT-2

IN from ANT

CH 3 CH 4

DVI/ HDCP

)

ANT( 75

Note:

If you have a mono VCR, connect L/Mono to VCR Audio OUT using only one audio cable.

If you have an S-VHS VCR, use an S-video cable instead of the standard video cable.

Do not connect a standard video cable and an S-video cable to Video-1 (or Video-2) at the same time or the picture performance will be unacceptable.

The unauthorized recording, use, distribution, or revision of television programs, videotapes, DVDs, and other materials is prohibited under the Copyright Laws of the United States and other countries, and may subject you to civil and criminal liability.

Connecting a cable converter box

Introduction

This connection allows you to watch basic and premium cable channels.

To use the TV’s features, select ANT-1. To view premium channels, select ANT-2, tune the TV to channel 3 or 4 (whichever channel is vacant in your area), and use the converter box to change channels.

You will need:

• three coaxial cables

DVI/ HDCP

ANT( 75

ANT-1

OUT

ANT-2

From Cable

)

Cable converter box

IN OUT

S-VIDEO

VIDEO

MONO

AUDIO

VIDEO-1 VIDEO-2

IR BLASTER

OUT

VAR. AUDIO

COLOR STREAM

AUDIO

HD 1

AUDIO

CENTER

CHANNEL IN

ON OFF

DVI/HDCP

VIDEO

MONO

AUDIO

OUT

AUDIO

COLOR STREAM HD 2

ININ

Connecting a cable converter box and VCR

This connection allows you to watch and record basic and premium cable channels, watch videotapes, and record one channel while watching another channel. To use the TV’s features, select ANT-1. To view premium channels or record with the VCR, select ANT-2, tune the TV to channel 3 or 4 (whichever channel is vacant in your area), and use the converter box to change channels.

You will need:

• four coaxial cables

• one set of standard A/V cables

S-VIDEO

VIDEO

MONO

AUDIO

VIDEO-1 VIDEO-2

IR BLASTER

OUT

VAR. AUDIO

COLOR STREAM

AUDIO

HD 1

AUDIO

CENTER

CHANNEL IN

ON OFF

DVI/HDCP

VIDEO

MONO

COLOR STREAM

AUDIO

HD 2

OUT

DVI/ HDCP

ANT( 75

ANT-1

AUDIO

OUT

ININ

ANT-2

)

From Cable

Cable converter box

OUT

Note:

When you use a converter box with your TV, the remote control will not operate some features, such as programming your favorite channels, labeling channels, and locking channels.

Note:

If you have a mono VCR, connect L/Mono to VCR Audio OUT using only one audio cable.

If you have an S-VHS VCR, use an S-video cable instead of a standard video cable. Do not connect a standard video cable and an S-video cable to Video-1 (or Video-2) at the same time or the picture performance will be unacceptable.

When you use a converter box with your TV, the remote control will not operate some features, such as programming your favorite channels, labeling channels, and locking channels.

Connecting

your TV

Remote Control

Using the

Setting up

your TV

Using the TV’s

Features

Appendix

Stereo VCR

VIDEO

OUT

AUDIO

OUT to TV

IN from ANT

CH 3 CH 4

Index

Connecting a DVD player or satellite receiver and a VCR

This connection allows you to watch DVD/satellite, VCR, and TV

Introduction

programs, and record one channel while watching another channel. You will need:

your TV

Connecting

Antenna

Using the

Remote Control

your TV

Setting up

• two (or three, if satellite receiver is used) coaxial cables

• one set of standard A/V cables (between the TV and VCR)

• one S-video cable (between the TV and DVD player/satellite receiver)

• one pair of standard audio cables (between the TV and DVD player/satellite receiver)

Stereo VCR

VIDEO AUDIO

OUT

DVI/ HDCP

)

ANT( 75

ANT-1

OUT

ANT-2

From

IN from ANT

CH 3 CH 4

OUT to TV

S-VIDEO

VIDEO

MONO

AUDIO

VIDEO-1 VIDEO-2

IR BLASTER

OUT

VAR. AUDIO

COLOR STREAM

AUDIO

HD 1

AUDIO

CENTER

CHANNEL IN

ON OFF

DVI/HDCP

VIDEO

MONO

AUDIO

OUT

AUDIO

COLOR STREAM HD 2

ININ

Note:

For the highest possible picture quality from a DVD player/satellite receiver without component video or DVI/HDCP, use an S-video cable between the TV and DVD player/satellite receiver. (If your DVD player/ satellite receiver is compatible with component video, see page 11. If your DVD player/satellite receiver is compatible with DVI/HDCP, see page 14).

Do not connect both an S-video cable and astandard video cable between the TV and DVD player/satellite receiver at the same time, or the picture performance will be unacceptable.

Do not connect the DVD player/satellite receiver and VCR to the same video channel on the TV. (See the illustrations, which show the DVD player/satellite receiver connected to Video-1 on the TV and the VCR connected to Video-2 on the TV.)

Features

Using the TV’s

Appendix

Index

From

Satellite

Dish

IN from ANT

S-VIDEO

VIDEO

OUTOUT

VIDEO

OUTOUT

DVD player

AUDIO

OUT

Satellite receiver

AUDIO

OUT

Connecting a DVD player with ColorStream

(component video) and a VCR

This connection allows you to watch DVD, VCR, and TV programs, and record TV programs. You can record one channel while watching another channel.

Your TV has ColorStream your TV to a DVD player with component video (such as a Toshiba DVD player with ColorStream and realism.

You will need:

• two coaxial cables

• one set of standard A/V cables

• one set of component video cables

• one pair of standard audio cables

From Antenna

(component video) inputs. Connecting

Stereo VCR

IN from ANT

CH 3 CH 4

OUT to TV

S-VIDEO

VIDEO

MONO

AUDIO

) can greatly enhance picture quality

VIDEO AUDIO

OUT

AUDIO

OUT

VIDEO

MONO

AUDIO

CENTER

CHANNEL IN

ON OFF

DVI/HDCP

COLOR STREAM HD 2

ININ

AUDIO

ANT-1

OUT

ANT-2

VIDEO-1 VIDEO-2

COLOR STREAM HD 1

IR BLASTER

OUT

VAR. AUDIO

AUDIO

DVI/ HDCP

ANT( 75

)

Note:

For the highest possible picture quality, use component video cables (or a DVI-D digital single-link cable) between the TV and DVD player.

You can connect component video cables from the DVD player to either ColorStream jack on the TV (HD1 or HD2).

The ColorStream HD1 and HD2 jacks can be used with Progressive (480p) and Interlaced (480i,1080i) scan systems.

If your DVD player is not compatible with component video (or DVI/HDCP), use an S-video cable (plus the standard audio cables) instead.

Do not connect both S-Video and standard video cables between the TV and DVD player at the same time, or the picture performance will be unacceptable.

Introduction

Connecting

your TV

Remote Control

Using the

Setting up

your TV

Using the TV’s

Features

RPB

VIDEO

OUT

S-VIDEO

COMPONENT VIDEO

DVD player with component video

AUDIO

OUT

LRL

Appendix

Index

Connecting a DTV receiver/set-top box with ColorStream® (component video) and a VCR

This connection allows you to watch DTV (digital TV broadcast),

Introduction

your TV

Connecting

Using the

Remote Control

your TV

Setting up

VCR, and TV programs, and record DTV and TV programs. You can record from one source while watching a program from another source.

Your TV has ColorStream your TV to a DTV receiver with component video can greatly enhance picture quality and realism.

You will need:

(component video) inputs. Connecting

• three coaxial cables

• two sets of standard A/V cables

• one set of component video cables

• one pair of standard audio cables

Stereo VCR

From Antenna

IN from ANT OUT to TV

S-VIDEO

VIDEO

AUDIO

MONO

VIDEO-1 VIDEO-2

VIDEO AUDIO

COLOR STREAM HD 1

IR BLASTER

OUT

VAR. AUDIO

AUDIO

OUT

VIDEO

MONO

OUT

AUDIO

CENTER

CHANNEL IN

ON OFF

DVI/HDCP

AUDIO

COLOR STREAM HD 2

ININ

Note:

For the highest possible picture quality, use component video cables (or a DVI-D digital single-link cable) between the TV and DTV receiver.

You can connect component video cables from the DTV receiver to either ColorStream jack on the TV (HD1 or HD2).

The ColorStream HD1 and HD2 jacks can be used with Progressive (480p) and Interlaced (480i,1080i) scan systems.

If your DTV receiver is not compatible with component video (or DVI/HDCP), use an S-video cable (plus the standard audio cables) instead.

Do not connect both S-Video and standard video cables between the TV and DTV receiver at the same time, or the picture

CH 3 CH 4

performance will be unacceptable.

To record from the DTV receiver, set the VCR to Line IN. To monitor recording from the DTV receiver, set the VCR to Line IN, and set the

DVI/ HDCP

)

ANT( 75

ANT-1

OUT

ANT-2

TV to Video-1.

Features

Using the TV’s

Appendix

Index

From DTV Antenna

RPBY

Satelite IN

S-VIDEO

COMPONENT VIDEO

DTV receiver with component video

VIDEO

OUT

AUDIO

OUT

Connecting two VCRs

This connection allows you to record (dub/edit) from one VCR to another VCR while watching a videotape. You also can record one channel while watching another channel.

You will need:

• two coaxial cables

• two sets of standard A/V cables

VCR1

VIDEO AUDIO

From Antenna

IN from ANT OUT to TV

S-VIDEO

VIDEO

MONO

AUDIO

VCR2

CH 3 CH 4

VIDEO-1 VIDEO-2

IR BLASTER

OUT

VAR. AUDIO

COLOR STREAM

AUDIO

HD 1

VIDEO AUDIO

AUDIO

OUT

VIDEO

MONO

AUDIO

CENTER

CHANNEL IN

ON OFF

DVI/HDCP

COLOR STREAM HD 2

OUT

CH 3 CH 4

DVI/ HDCP

)

ANT( 75

ANT-1

AUDIO

OUT

ININ

ANT-2

Connecting a camcorder

Note:

If you have S-VHS VCRs, use S-video cables instead of standard video cables. Do not connect both a standard video cable and an S-video cable to Video-1 (or Video-2) at the same time, or the picture performance will be unacceptable.

Do not connect the same VCR to the output and input jacks on the TV at the same time.

To dub or edit, VCR 2 must select Line IN, and the TV must select Video-1.

The Video OUT jack does not output the

POP picture.

The Audio OUT jacks can output the sound

of either the Main or POP picture (see “Selecting the Audio OUT sound” on page 56).

Introduction

Connecting

your TV

Remote Control

Using the

Setting up

your TV

Using the TV’s

Features

This connection allows you to watch video materials recorded on a camcorder.

You will need:

• one set of standard A/V cables

Camcorder

VIDEO

AUDIO

OUT

VIDEO-3 IN

AUDIO

S-VIDEO

VIDEO

L/MONO R

Video-3 (front panel)

Note:

If you have an S-VHS camcorder, use an S-video cable instead of a standard video cable. Do not connect both a standard video cable and an S-video cable at the same time, or the picture performance will be unacceptable.

Appendix

Index

Connecting a device to the DVI/HDCP1 input

The DVI/HDCP input on your TV is designed to accept HDCP program material in digital form from EIA/CEA-861–compliant

Introduction

consumer electronic devices, such as a set-top box or DVD player equipped with a DVI-D digital single-link output connection.

The DVI/HDCP input is designed for best performance with 1080i high-definition video signals. The DVI/HDCP input also will accept and display 480p and 480i picture signals.

your TV

Connecting

You will need:

Using the

Remote Control

Note: This TV is not intended for connection to and should not be used with a PC (personal computer).

• one DVI-D digital single-link cable

Note: For proper operation, the DVI-D cable length should not exceed 3m (9.8 ft). The recommended length is 2m (6.6 ft).

• one pair of standard audio cables

DVI/HDCP device (for example, set-top box or DVD player)

VIDEO AUDIO

OUT

DVI/ HDCP

OUT

DVI/HDCP = Digital Visual Interface/ High-bandwidth Digital Content Protection.

Notes

EIA/CEA-861 compliance covers the transmission of uncompressed digital video with high-bandwidth digital content protection, which is being standardized for future reception of high-definition video signals.

Consult your consumer electronics dealer for availability.

Caution

To ensure that the DVI/ HDCP device is reset properly, it is recommended that you follow these procedures:

• When turning on your electronic

components, turn on the TV first, and then the DVI/HDCP device.

• When turning off your electronic

components, turn off the DVI/HDCP device first, and then the TV.

your TV

Setting up

Features

Using the TV’s

Appendix

S-VIDEO

VIDEO

MONO

AUDIO

VIDEO-1 VIDEO-2

VIDEO

OUT

MONO

AUDIO

CENTER

CHANNEL IN

ON OFF

DVI/HDCP

AUDIO

COLOR STREAM HD 2

ININ

DVI/ HDCP

)

ANT( 75

ANT-1

OUT

ANT-2

IR BLASTER

OUT

VAR. AUDIO

COLOR STREAM

HD 1

AUDIO

Index

Connecting a device to the IR blaster

The IR blaster allows you to remotely operate (through the TV) most infrared-controlled devices* (such as a Toshiba infraredcontrolled VCR or DVD player) enclosed within an entertainment center or similar cabinet. Without the IR blaster, the device typically would need to be visible to operate it remotely.

You can use the TV’s remote control (programmed to operate the device; see pages 17–23) or the device’s remote control. Point the remote control at the front of the TV and press the button for the desired function. The signal passes from the remote control through the TV to the device via the IR blaster cable (included with your TV).

To connect, align the IR blaster cable’s infrared “eye” with the device’s infrared sensor and attach it using double-sided mounting tape (included with the cable in the accessory pack). Plug the other end of the IR blaster cable into the TV’s IR BLASTER OUT terminal.

You will need:

• one IR blaster cable (included)

• one piece of double-sided mounting tape (included)

Front of infrared-controlled device* (such as a Toshiba infrared-controlled

IR blaster cable’s

infrared “eye”

facing device’s

infrared sensor

VCR or DVD player)

Back of TV

IR BLASTER

OUT

AUDIO

CENTER

CHANNEL IN

DVI/ HDCP

For additional control options for your home theater system, you can connect an IR receiver/repeater (not included) or a home theater control system (not included) to the TV’s IR BLASTER IN terminal.*

See the Specifications section in the back of this manual for IR BLASTER IN terminal requirements.

Contact your home theater electronics dealer for details about home theater control systems.

Back of TV

AUDIO

S-VIDEO

VIDEO

MONO

AUDIO

VIDEO-1 VIDEO-2

IR BLASTER

CHANNEL IN

OUT

ON OFF

OUT

VAR. AUDIO

VIDEO

MONO

AUDIO

COLOR STREAM HD 2

OUT

COLOR STREAM HD 1

CENTER

DVI/HDCP

AUDIO

ININ

OUT

DVI/HDCP

ANT( 75

ANT-1

OUT

ANT-2

Introduction

Connecting

your TV

Remote Control

)

Using the

Setting up

your TV

C T

9 0

1 2 1

S-VIDEO

VIDEO

MONO

AUDIO

VIDEO-1 VIDEO-2

ON OFF

COLOR STREAM HD 1

OUT

VAR. AUDIO

AUDIO

OUT

VIDEO

MONO

DVI/HDCP

AUDIO

COLOR STREAM HD 2

ININ

)

ANT( 75

ANT-1

OUT

ANT-2

With this connection, point the Toshiba TV remote control at the front of the TV to operate both the TV and the infrared-controlled device. (You also can point the device’s remote control at the TV to operate the device, but you also will need to use the TV’s remote control to operate the TV.)

IR receiver/repeater

or home theater

control system

9 0

1 2 1

Back of IR receiver/ repeater or home theater control system* (not included)

With this connection, point the Toshiba TV remote control at the front of the IR receiver/ repeater or home theater control system to operate the TV.

Using the TV’s

Features

Appendix

Index

___________

*The IR blaster OUT function has been verified for use with Toshiba infrared-controlled devices. The IR blaster IN function has been verified for use with

SmarTouch™ STS/STS-C wireless RF control systems. Due to the wide

variation in remote control operation among manufacturers, these functions may or may not operate with other brands.

SmarTouch is a trademark of Crestron Electronics, Inc. (www.crestron.com).

Connecting an audio system

This connection allows you to use an audio amplifier to adjust the audio level. This also allows you to use external speakers.

Introduction

To control the audio, turn on the TV and the stereo amplifier, and turn off the built-in speakers (see “Turning off the built-in speakers” on page 56).

You will need:

Note:

To hear sound when using an external audio amplifier,

your TV

Connecting

the volume of both the TV and the amplifier must be set above 0 (zero).

Connecting an A/V receiver

This connection allows you to use an A/V (audio/video) receiver to enhance your TV’s sound.

If you have a system with Dolby Pro Logic add to the realism of the sound by using the TV’s internal speakers as center channel speakers.

Using the

Remote Control

You will need:

• one pair of audio cables

surround sound, you can

• one set of standard A/V cables

• one single audio cable for the audio center channel

To A/V receiver

Amplifier

LINE IN LR

AUDIO

S-VIDEO

VIDEO

MONO

AUDIO

VIDEO-1 VIDEO-2

IR BLASTER

OUT

VAR.

AUDIO

VIDEO

MONO

COLOR STREAM

AUDIO

HD 1

OUT

CENTER

CHANNEL IN

ON OFF

DVI/HDCP

COLOR STREAM HD 2

ININ

AUDIO

DVI/HDCP

ANT( 75

ANT-1

OUT

ANT-2

Caution:

To avoid damaging the speakers:

• Turn off the TV off before connecting or disconnecting the Audio Center Channel cable.

• Do not connect from the A/V receiver’s Center Speaker OUT (amplified signal) to the TV’s Audio Center Channel IN.

)

your TV

Setting up

Features

Using the TV’s

Appendix

Index

Video

OUT

S-VIDEO

VIDEO

MONO

AUDIO

VIDEO-1 VIDEO-2

COLOR STREAM HD 1

IR BLASTER

OUT

VAR. AUDIO

AUDIO

OUT

VIDEO

MONO

AUDIO

CENTER

CHANNEL IN

ON OFF

DVI/HDCP

COLOR STREAM HD 2

ININ

Center

OUT

ANT-1

AUDIO

OUT

ANT-2

DVI/ HDCP

ANT( 75

)

From Antenna

Note:

Refer to the instructions provided with your A/V receiver for details about your surround sound system.

When the Audio Center Channel ON/OFF switch is in the ON position, the TV speakers will function only as center channel speakers.

Adjust the volume for the center channel speakers using the center level control on the A/V receiver.

To use the TV speakers as normal speakers, set the Audio Center Channel ON/OFF switch to the OFF position.

ON OFF

Dolby Pro Logic* surround sound

system connection example

Audio Video

VCR

Video

A/V receiver

Audio

Video

T V

Left speaker

Surround speaker L

_________

* Dolby Pro Logic is a registered trademark

of Dolby Laboratories Licensing Corporation.

Audio

LDP/DVD

center

channel

Surround speaker R

Right speaker

Using the remote control

Introduction

Preparing the remote control for use

Your Toshiba TV remote control has one dedicated TV mode and five universal modes: VCR, Cable/SAT, DVD, Audio1, and Audio2. The target devices and default devices being programmed for each mode are as follows:

Target device/Mode mapping

Mode Device TV Toshiba TV CABLE/SAT Universal Cable, Satellite VCRUniversal VCR, DVD, LD, Cassette DVDUniversal DVD, VCR, LD, Cassette AUDIO1 Universal Audio: Amp., Tuner, Misc.Audio, CD/MD AUDIO2 Universal Audio: CD/MD, Amp., Tuner, Misc.Audio

Default device codes

Mode Default device TV Toshiba TV CABLE/SAT Toshiba Satellite receiver VCRToshiba VCR DVDToshiba DVD AUDIO1 Pioneer Audio receiver AUDIO2 Pioneer LD

Note:

Your TV’s remote control may not operate certain features on your VCR, cable TV converter, or other electronic device.

Refer to the owner’s manuals for your other devices to determine their available features. If your TV’s remote control does not operate a specific feature on a device, use the remote control that came with the device.

MODE

Connecting

your TV

Remote Control

Using the

Setting up

your TV

Repeatedly press MODE to cycle among the modes. If you own different brands of audio/video devices, you must first program your remote control (see “Programming the remote control for use with your audio/video devices” on page 20).

Installing the remote control batteries

To install the batteries:

1. Slide the battery cover off the back of the remote control.

2. Install two “AA” size alkaline batteries. Match the + and – signs on the batteries to the signs on the battery compartment.

Caution:

• Dispose of batteries in a designated disposal area. Do not throw batteries into afire.

• Do not mix battery types or combine used batteries with new ones.

• If the batteries are dead or if you will not use the remote control for a long time, remove the batteries to prevent battery acid from leaking into the battery compartment.

Note:

• Battery life expectancy is about one year with normal use.

Using the TV’s

Features

Appendix

Index

3. Slide the battery cover back on to the remote control until the lock snaps.

Remote Control functional key chart

Introduction

your TV

Connecting

Using the

Remote Control

your TV

Setting up

Features

Using the TV’s

Appendix

Index

LIGHT Lights the remote key, and toggles between enabled and disabled Illumination mode. SLEEP Sleep timer --- --- --- --- --- --- --POWER Power Power Power Power Power Power Power Power 1/MOVIE Digit 1 Digit 1 Digit 1 Digit 1 Digit 1 AV input 1 Digit 1 Digit 1 2/SPORTS Digit 2 Digit 2 Digit 2 Digit 2 Digit 2 AV input 2 Digit 2 Digit 2 3/NEWS Digit 3 Digit 3 Digit 3 Digit 3 Digit 3 AV input 3 Digit 3 Digit 3 4/SERVICES Digit 4 Digit 4 Digit 4 Digit 4 Digit 4 AV input 4 Digit 4 Digit 4 5/LIST Digit 5 Digit 5 Digit 5 Digit 5 Digit 5 CD Digit 5 Digit 5 6Digit 6 Digit 6 Digit 6 Digit 6 Digit 6 Tuner Digit 6 Digit 6

MODE Remote control device mode selection

PIC SIZE Selects the TV TV TV TV TV TV TV

7Digit 7 Digit 7 Digit 7 Digit 7 Digit 7 Phono Digit 7 Digit 7 8Digit 8 Digit 8 Digit 8 Digit 8 Digit 8 Cassette Digit 8 Digit 8 9Digit 9 Digit 9 Digit 9 Digit 9 Digit 9 Aux Digit 9 Digit 9 ACTION --- --100/– 100 --- 100 100 100 100 100 100 0Digit 0 Digit 0 Digit 0 Digit 0 Digit 0 Digit 0 Digit 0 Digit 0 ENT --- CH Enter CH Enter CH Enter --- --- --- --GUIDE/SETUP INFO/TITLE --- --- INFO --- TITLE= --- --- ---

FAVORITE/ Favorite CH --SUBTITLE

ALPHASORT/ --- --- Alphasort --- Audio --- --- --AUDIO

MENU/ Menu open/ --- Select --- Enter --- --- --ENTER Enter

yz Menu select --- Menu select --- Menu select --- --- --- x •/FAV zy Menu select/ --- Menu select --- Menu select --- --- ---

VOL yz Volume Volume Volume Volume Volume Volume Volume ---

EXIT/ Exit Exit Exit Exit DVD clear Exit/Clear Exit/Clear Exit/Clear DVD CLEAR

INPUT TV/Video TV TV VCR input TV Input TV TV

MUTE RECALL On-screen

CH RTN/ Previous Previous Previous Previous DVD --- --- --DVD RTN channel channel channel channel return

SLOW/ DIR x--- --- --- --- Reverse --- --- ---

SKIP/ SEARCH x--- --- --- --- Reverse

REW VCR VCR VCR Rewind Rewind Rewind Rewind Rewind PAUSE/STEP VCR VCR VCR Pause Pause Pause Pause Pause PLAY VCR VCR VCR Play Play Play Play Play FF VCR VCR VCR F. Forward F. Forward F. Forward F. Forward F. Forward

Key Label

yz Channel Channel Channel Channel --- Channel --- ---

Toshiba TV Cable Satellite VCR DVD/LD Receiver CD/MD Cassete

(TV) (CBL/SAT) (CBL/SAT) (AUDIO) (AUDIO) (VCR)

image shape.

Action, Menu

--- --- Guide --- DVD setup --- --- ---

Favorite CH

FAV zy

up/down* up/down* up/down* up/down* up/down* up/down* up/down*

up/down up/down up/down up/down up/down

select Sound mute* Sound mute* Sound mute* Sound mute* Sound mute* Sound mute* Sound mute*

---

display display display display

•

--- --- --- Forward Forward --- --- ---

•

--- --- --- --- Forward

On-screen On-screen On-screen --- --- ---

--- Menu --- --- ---

Top menu

--- Subtitle --- --- ---

---

Forward Forward Reverse Reverse

---

Introduction

Key Label

TV/VCR VCR AM/FM DISC --- --- --- --- Disc shift AM/FM Disc shift Deck side

STOP VCR VCR VCR Stop Stop Stop Stop Stop REC

PIP CH

PIPPIP on/off TV TV TV TV TV TV TV MULTI STILL PIP Still TV TV TV TV TV TV TV SWAP PIP Swap TV TV TV TV TV TV TV LOCATE PIP Locate TV TV TV TV TV TV TV SOURCE PIP Source TV TV TV TV TV TV TV

Notes:

•“---” will send nothing.

•“ TV” will jump to TV.

•“ VCR” will jump to last active VCR or DVD. Active VCR/DVD is defined as the mode that remains for a minimum of 5

seconds, or if a key is pressed in that mode.

The VOLUME and MUTE will jump to “TV” by default. When the volume is unlocked, all the devices will have their own volume. The AUDIO1/2 (Receiver, CD) modes will have their own volume even if Volume Lock is on TV, CABLE/SAT, VCR, or DVD. See “Using the Volume Lock feature” on page 21.

Press the REC button two times within 5 seconds to record each A/V source.

Toshiba TV Cable Satellite VCR DVD/LD Receiver CD/MD Cassete

(TV) (CBL/SAT) (CBL/SAT) (AUDIO) (AUDIO) (VCR)

---

VCRVCR VCR Record** --- Record** Record** Record** PIP channel TV TV TV TV TV TV TV

up/down

Strobe TV TV TV TV TV TV TV

TV/SAT TV/VCR --- --- --- Reverse

A/B switch

Connecting

your TV

Remote Control

Using the

Setting up

your TV

Using the TV’s

Features

Appendix

Index

Programming the remote control for use with your audio/video devices

Introduction

your TV

Connecting

Using the

Remote Control

Device code setup

1. Refer to the Device code table on pages 22–23 to find the code for the brand of your device.

If more than one code is listed, try each one separately until you find the one that works.

2. Press MODE until the Mode indicator of the device (CABLE/ SAT, VCR, DVD, AUDIO1, AUDIO2) lights up.

3. While holding down the RECALL button, press the Channel Number buttons to enter the four-digit code of your brand of device. If a valid code is entered, the mode indicator will blink twice. If an invalid code is entered, the mode indicator will blink one long blink.

4. Point the remote control at the device and press POWER to test the code.

If the device turns on, you have entered the correct code. If the device does not respond to the remote control, you may

have entered the wrong code. Repeat steps 3 and 4 using another code.

5. Press MODE to select the TV mode to control the TV.

Note:

• Every time you replace the batteries, you must reprogram the remote control.

• Some newer VCRs are capable of working on either of two remote codes.These VCRs have a switch labeled “VCR1/VCR2.”

If your VCR has this kind of switch and does not respond to any of the codes for your VCR brand, set the switch to the other position (VCR1 or VCR2) and reprogram the remote control

your TV

Setting up

Features

Using the TV’s

Appendix

Searching and sampling the code of a device (8500)

If you do not know the device code for a particular target unit, you can cycle the remote control through the available codes for that device mode and sample the functions to find the code that properly operates the target device. The keys available to be sampled, provided they are applicable to that mode, are POWER, 1, VOL y, CH y, and PLAY. Invalid keys will be ignored while in program mode.

To cycle through each available device code and sample its functions:

1. Press MODE to select the mode you want to set up.

2. While holding down the RECALL button, press 8 –5 –0 –0. The remote control will enter program mode.

3. Point the remote control at the target device and press POWER (or other function buttons that are available to be sampled).

4. If the device responds to the remote control:

Press RECALL to store the device code. The mode indicator will blink twice and the remote control will exit the program mode.

If the device does not respond to the remote control:

Press y, and then press POWER. Repeat this step until the device responds to the remote control, and then press RECALL.

Note: When a search cycle is completed, the mode indicator will blink

three times. The remote control will begin to cycle through the available codes again. If no key is pressed within 10 seconds while programming, the remote control will exit the program mode and return to the previous code.

POWER

Numbers

MODE

RECALL

Index

+ 44 hidden pages