Toshiba 52XV540U, 46XV540U, 42XV540U User Manual

Integrated High Definition LCD Television

HIGH-DEFINITION TELEVISION

42XV540U 46XV540U 52XV540U

For an overview of steps for setting up your new TV, see page 9.

Note: To display a High Definition picture, the TV must be receiving a High Definition signal (such as an over-the-air High Definition TV broadcast, a High Definition digital cable program, or a High Definition digital satellite program). For details, please contact your TV antenna installer, cable provider, or satellite provider.

Owner’s Record

The model number and serial number are on the back of your TV. Record these numbers in the spaces below. Refer to these numbers whenever you communicate with your Toshiba dealer about this TV.

Model number:

Serial number:

YC/M1

VX1A00098300

Dear Customer,

Thank you for purchasing this Toshiba LCD TV. This manual will help you use the many exciting features of your new LCD TV. Before operating your LCD TV, please read this manual completely, and keep it nearby for future reference.

CHILD SAFETY:

It Makes A Difference How and Where You Use Your Flat Panel Display

Safety Precautions

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN.

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING

To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions. See item 20 on page 3 and instructions on page 5.

WARNING: If you decide to wall mount this television,

always use a UL Listed wall bracket appropriate for the size and weight of this television. The use of any wall bracket other than a UL Listed wall bracket appropriate for the size and weight of this television for wall mounting this television could result in serious bodily injury and/or property damage. See “Removing the Pedestal Stand” (- page 5).

NOTE TO CATV INSTALLERS

This is a reminder to call the CATV system installer’s attention to Article 820-40 of the U.S. NEC, which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. For additional antenna grounding information, see items 27 and 28 on page 4.

Congratulations on your purchase! As you enjoy your new product, please keep these safety tips in mind:

The Issue

• The home theater entertainment experience is a growing trend and larger flat panel displays are popular purchases. However, flat panel displays are not always supported on the proper stands or installed according to the manufacturer’s recommendations.

• Flat panel displays that are inappropriately situated on dressers,

bookcases, shelves, desks,

speakers, chests or carts may fall

over and cause injury.

TOSHIBA Cares!

• The consumer electronics industry is committed to making home

entertainment enjoyable and safe.

Tune Into Safety

•

One size does NOT fit all. Follow the manufacturer’s recommendations for the safe installation and use of your flat panel display.

• Carefully read and understand all enclosed instructions for proper use of this product.

• Don’t allow children to climb on or play with furniture and television sets.

• Don’t place flat panel displays on furniture that can easily be used as steps, such as a chest of drawers.

• Remember that children can become excited while watching a program, especially on a “larger than life” flat panel display. Care should be taken to place or install the display where it cannot be pushed, pulled over, or knocked down.

• Care should be taken to route all cords and cables connected to the flat panel display so that they cannot be pulled or grabbed by curious children.

Wall Mounting: If you decide to wall mount your flat panel display, always:

• Use a mount that has been recommended by the display manufacturer and/or listed by an independent laboratory (such as UL, CSA, ETL).

• Follow all instructions supplied by the display and wall mount manufacturers.

• If you have any doubts about your ability to safely install your flat panel display, contact your retailer about professional installation.

• Make sure that the wall where you are mounting the display is appropriate. Some wall mounts are not designed to be mounted to walls with steel studs or old cinder block construction. If you are unsure, contact a professional installer.

• A minimum of two people are required for installation. Flat panel displays can be heavy.

Important Safety Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of

the polarized or grounding type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the

manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use

caution when moving the cart/apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or

when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Additional Safety Precautions

14a) CAUTION: If the TV is dropped and the cabinet or

enclosure surface has been damaged or the TV does not operate normally, take the following precautions:

• ALWAYS turn off the TV and unplug the power cord to

avoid possible electric shock or fire.

• NEVER allow your body to come in contact with any

broken glass or liquid from the damaged television. The LCD panel inside the TV contains glass and a toxic liquid. If the liquid comes in contact with your mouth or eyes, or your skin is cut by broken glass, rinse the affected area thoroughly with water and consult your doctor.

• ALWAYS contact a service technician to inspect the TV

any time it has been damaged or dropped.

Wide blade

15) CAUTION:

• To reduce the risk of electric shock, do not use the polarized plug with an extension cord, receptacle, or other outlet unless the blades can be inserted completely to prevent blade exposure.

• To prevent electric shock, match wide blade of plug to wide slot; fully insert.

16) WARNING: To prevent the spread of fire, keep candles or other open flames away from this product at all times.

Installation, Care, and Service

Installation

Follow these recommendations and precautions and heed all warnings when installing your TV:

17) Never modify this equipment. Changes or modifications may void: a) the warranty, and b) the user’s authority to operate this equipment under the rules of the Federal Communications Commission.

18) DANGER: RISK OF

SERIOUS PERSONAL INJURY, DEATH, OR EQUIPMENT DAMAGE!

Never place the TV on an unstable cart, stand, or table. The TV may fall, causing serious personal injury, death, or serious damage to the TV.

19) To avoid damage to this product, never place or store the TV in direct sunlight; hot, humid areas; or areas subject to excessive dust or vibration.

20) Always place the TV on the floor or a sturdy, level, stable surface that can support the weight of the unit. To secure the TV, use a sturdy strap from the hooks on the rear of the TV pedestal to a wall stud, pillar, or other immovable structure. Make sure the strap is tight, secure, and parallel to the floor.

Sturdy strap (as short as possible)

min.

Securement Clip

TV side TV top

21) The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

22) Never block or cover the slots or openings in the TV cabinet back, bottom, and sides. Never place the TV:

• on a bed, sofa, rug, or similar

surface;

• too close to drapes, curtains, or

walls; or

• in a confined space such as a

bookcase, built-in cabinet, or any

other place with poor ventilation. The slots and openings are provided to protect the TV from overheating and to help maintain reliable operation of the TV. Leave a space of at least 4 (four) inches around the TV.

Hooks

Securement Clip

(continued)

23) Always place the back of the television at least four (4) inches away from any vertical surface (such as a wall) to allow proper ventilation.

24) Never allow anything to rest on or roll over the power cord, and never place the TV where the power cord is subject to wear or abuse.

25) Never overload wall outlets and extension cords.

26) Always operate this equipment from a 120 VAC, 60 Hz power source only.

27) Always make sure the antenna system is properly grounded to provide adequate protection against voltage surges and built-up static charges (see Section 810 of the National Electric Code).

Antenna lead-in wire

Antenna discharge unit

Ground clamp

Electric service equipment

(NEC Section 810-20)

Grounding conductors (NEC Section 810-21)

31)

WARNING:

RISK OF ELECTRIC SHOCK!

Never spill liquids or push objects of any kind into the TV cabinet slots.

32) While it is thundering, do not touch the connecting cables or apparatus.

33) For added protection of your TV from lightning and power surges, always unplug the power cord and disconnect the antenna from the TV if you leave the TV unattended or unused for long periods of time.

34) During normal use, the TV may make occasional snapping or popping sounds. This is normal, especially when the unit is being turned on or off. If these sounds become frequent or continuous, unplug the power cord and contact a Toshiba Authorized Service Center.

35)

WARNING: RISK OF SERIOUS PERSONAL INJURY OR EQUIPMENT DAMAGE!

Never strike the screen with a sharp or heavy object.

Power service grounding electrode system (NEC Art 250 Part-H)

28)

Ground clamps

DANGER: RISK OF SERIOUS

PERSONAL INJURY OR DEATH!

• Use extreme care to make sure you are never in a position where your body (or any item you are in contact with, such as a ladder or screwdriver) can accidentally touch overhead power lines. Never locate the antenna near overhead power lines or other electrical circuits.

• Never attempt to install any of the following during lightning activity: a) an antenna system; or b) cables, wires, or any home theater component connected to an antenna or phone system.

Care

For better performance and safer operation of your TOSHIBA TV, follow these recommendations and precautions:

29) If you use the TV in a room whose temperature is 32 ºF (0 ºC) or below, the picture brightness may vary until the LCD warms up. This is not a sign of malfunction.

30) Always unplug the TV before cleaning. Gently wipe the display panel surface (the TV screen) using a dry, soft cloth only (cotton, flannel, etc.). A hard cloth may damage the surface of the panel. Avoid contact with alcohol, thinner, benzene, acidic or alkaline solvent cleaners, abrasive cleaners, or chemical cloths, which may damage the surface. Never spray volatile compounds such as insecticide on the cabinet. Such products may damage or discolor the cabinet. In addition, gently wipe the luster finishing portion of your TV with the enclosed cleaning cloth after removing any dirt or dust from the surface. Harsh rubbing or use of a dirty cleaning cloth or stiff cloth will scratch your TV.

36) • The LCD screen of this product can be damaged by ultraviolet radiation from the sun. When selecting a location for the television, avoid locations where the screen may be exposed to direct sunlight, such as in front of a window.

• Never touch, press, or place anything on the LCD screen. These actions will damage the LCD screen. If you need to clean the LCD screen, follow the instructions in item 30 on this page.

Service

37)

RISK OF ELECTRIC SHOCK!

Never attempt to service the TV yourself. Opening and removing the covers may expose you to dangerous voltage or other hazards. Failure to follow this WARNING may result in death or serious injury. Refer all servicing not specified in this manual to a Toshiba Authorized Service Center.

38) If you have the TV serviced:

• Ask the service technician to use only replacement parts specified by the manufacturer.

• Upon completion of service, ask the service technician to perform routine safety checks to determine that the TV is in safe operating condition.

39) The cold cathode fluorescent lamp in the LCD panel contains a small amount of mercury.

When the TV reaches the end of its useful life, dispose of the used TV by the approved method for your area, or ask a qualified service technician to properly dispose of the TV.

Note: The lamp(s) inside this product contain mercury. Disposal may be regulated due to

environmental considerations. For disposal or recycling information, contact your local authorities or the Electronics Industries Alliance (www.eiae.org).

WARNING:

Choosing a location for your LCD TV

To Display your LCD TV on the included Pedestal Stand:

Observe the following safety precautions:

1) Read and Follow the pedestal assembly instructions included with the pedestal. (for 42XV540U only)

CAUTION: Before beginning pedestal assembly, carefully lay the front of the LCD Panel face down on a flat, cushioned surface such as a quilt or blanket. Leave the bottom of the unit protruding over the edge of the surface and assemble the pedestal as indicated below.

Note: Extreme care should always be used when attaching the pedestal stand to avoid damage to the LCD panel.

2) Place the TV on a sturdy, level surface that can support the weight of the TV.

3) Be sure to secure the TV to a wall stud, pillar, surface, or other immovable structure. To secure the TV in this manner: (1) attach the provided securement clip to an immovable structure, then (2) pass a sturdy strap through the securement clip and attach each end to the hooks located on the back of the TV. Be sure to leave at least 4 inches between the TV and the wall or similar structure for ventilation. See item 20, page 3 for additional details.

To Display your LCD TV using a Wall Bracket:

If you decide to wall mount your LCD TV, always use a ULlisted wall bracket appropriate for the size and weight of the LCD TV (- page 2) :

1) CAUTION: Two people are required for installation.

2) Unplug and remove any cables and/or other component connectors from the rear of the TV.

3) Follow the instructions provided with your wall bracket. Before proceeding, make sure the appropriate bracket(s) are attached to the wall and the back of the TV as described in the instructions provided with the wall bracket.

4) After attaching the appropriate bracket(s) to the wall and the back of the TV, remove the pedestal stand from the TV as described below.

Removing the Pedestal Stand

1) Carefully lay the front of the unit face down on a flat, cushioned surface such as a quilt or blanket. Leave the stand protruding over the edge of the surface.

Note: Extreme care should always be used when removing the pedestal stand to avoid damage to the LCD panel.

2) Remove the four screws shown in the diagram below. This will allow removal of the pedestal stand.

3) Once you have removed all four screws holding the pedestal stand in place, remove the pedestal stand from the TV by sliding the pedestal stand away from the TV.

Four screws

FCC Declaration of Conformity

Important notes about your LCD Compliance Statement (Part 15):

The Toshiba 42XV540U, 46XV540U, and 52XV540U

Televisions

Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The party responsible for compliance to these rules is: Toshiba America Consumer Products, L.L.C. 82 Totowa Rd. Wayne, NJ 07470. Ph: 1-800-631-3811

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by removing and applying power to the equipment, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the

receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for

help.

Caution: Changes or modifications to this equipment not expressly approved by Toshiba could void the user’s authority to operate this equipment.

comply with Part 15 of the FCC rules.

The following symptoms are technical limitations of LCD

Display technology and are not an indication of malfunction;

therefore, Toshiba is not responsible for perceived issues

resulting from these symptoms.

1) An afterimage (ghost) may appear on the screen if a fixed, nonmoving image is displayed for a long period of time. The afterimage is not permanent and will disappear in a short period of time.

2) The LCD panel contained in this TV is manufactured using an extremely high level of precision technology; however, there may be an occasional pixel (dot of light) that does not operate properly (does not light, remains constantly lit, etc.). This is a structural property of LCD technology, is not a sign of malfunction, and is not covered under your warranty. Such pixels are not visible when the picture is viewed from a normal viewing distance.

Note: Interactive video games that involve shooting a “gun” type of joystick at an on-screen target may not work with this TV.

Trademark Information

• Manufactured under license from Dolby Laboratories.

“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

• HDMI, the HDMI logo and High-Definition Multimedia Interface are

trademarks or registered trademarks of HDMI Licensing LLC.

• Deep Color is trademark of HDMI Licensing LLC.

• “x.v.Color” and the “x.v.Color” logo are trademarks of Sony

Corporation.

Contents

Important Safety Instructions .......................................... 3

Installation, Care, and Service ........................................ 3

Chapter 1: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Features of your new TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Overview of steps for installing, setting up, and using

your new TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

TV front and side panel controls and connections . . . . . . . . 10

TV back panel connections. . . . . . . . . . . . . . . . . . . . . . . . . . 11

Chapter 2: Connecting your TV . . . . . . . . . . . . . . . . . . . . . . .12

Overview of cable types . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

About the connection illustrations . . . . . . . . . . . . . . . . . . . . 12

Connecting a VCR (or a VCR with S-video) and antenna,

Cable TV or Camcorder . . . . . . . . . . . . . . . . . . . . . . . . . 13

Connecting a DVD player with ColorStream

(component

video), a VCR, and a satellite receiver. . . . . . . . . . . . . . 14

Connecting a device to the IR OUT infrared terminal

using the IR blaster cable for IR pass-through device

control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Connecting an HDMI

™

or DVI device to the HDMI

input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

REGZA-LINK connection . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Connecting a digital audio system . . . . . . . . . . . . . . . . . . . . 18

Connecting an audio system . . . . . . . . . . . . . . . . . . . . . . . . . 18

Connecting a personal computer (PC) . . . . . . . . . . . . . . . . . 19

Chapter 3: Using the remote control . . . . . . . . . . . . . . . . . . .20

Preparing the remote control for use. . . . . . . . . . . . . . . . . . . 20

Installing the remote control batteries . . . . . . . . . . . . . . . . . 20

Learning about the remote control . . . . . . . . . . . . . . . . . . . . 21

Remote Control functional key chart . . . . . . . . . . . . . . . . . . 22

Using the remote control to operate your other devices . . . . 24

Programming the remote control to operate your other

devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Device code setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Searching and sampling the code of a device (8500). . . 25

Using the volume lock feature (8000) . . . . . . . . . . . . . . 25

Operational feature reset (8900). . . . . . . . . . . . . . . . . . . 25

Multi-brand remote control device codes . . . . . . . . . . . . . . . 26

Chapter 4: Menu layout and navigation . . . . . . . . . . . . . . . . .33

Main menu layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Setup/Installation menu layout . . . . . . . . . . . . . . . . . . . . . . . 33

™

THINC

menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Navigating the menu system. . . . . . . . . . . . . . . . . . . . . . . . . 34

Chapter 5: Setting up your TV. . . . . . . . . . . . . . . . . . . . . . . .35

Setting the Demo Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Selecting the menu language . . . . . . . . . . . . . . . . . . . . . . . . 35

Configuring the input source for the

ANT/CABLE terminal . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Programming channels into the TV’s channel memory . . . . 36

Programming channels automatically . . . . . . . . . . . . . . 36

Manually adding and deleting channels in the channel

memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Setting the Auto Input feature. . . . . . . . . . . . . . . . . . . . . . . . 37

Labeling channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Setting the HDMI

™

audio mode . . . . . . . . . . . . . . . . . . . . . . 39

Viewing the digital signal meter. . . . . . . . . . . . . . . . . . . . . . 39

Setting the time zone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Viewing the system status. . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Selecting the Power-On Mode . . . . . . . . . . . . . . . . . . . . . . . 40

Selecting the Demo Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Chapter 6: Using the TV’s features . . . . . . . . . . . . . . . . . . . .41

Selecting the video input source to view . . . . . . . . . . . . . . . 41

Labeling the video input sources . . . . . . . . . . . . . . . . . . . . . 41

Tuning channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Tuning channels using the Channel Browser

™

. . . . . . . 42

Setting the Channel Tuning Mode . . . . . . . . . . . . . . . . . 44

Tuning to the next programmed channel . . . . . . . . . . . . 44

Tuning to a specific channel (programmed or

unprogrammed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Switching between two channels using Channel

Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Switching between two channels using SurfLock

Selecting the picture size . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Scrolling the TheaterWide

picture

™

. . . . 45

(TheaterWide 2 and 3 only) . . . . . . . . . . . . . . . . . . . . . . 47

Using the auto aspect ratio feature . . . . . . . . . . . . . . . . . . . . 47

Using the FREEZE feature . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Adjusting the picture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Selecting the picture mode. . . . . . . . . . . . . . . . . . . . . . . 48

Adjusting the picture quality . . . . . . . . . . . . . . . . . . . . . 48

Using the TheaterLock

™

feature. . . . . . . . . . . . . . . . . . . . . . 49

Using the closed caption mode. . . . . . . . . . . . . . . . . . . . . . . 49

Base closed captions . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Digital CC Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

CC Selector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Using the Closed Caption button on the remote

control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Adjusting the audio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Muting the sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Using the digital audio selector . . . . . . . . . . . . . . . . . . . 51

Selecting stereo/SAP broadcasts . . . . . . . . . . . . . . . . . . 51

Adjusting the audio quality . . . . . . . . . . . . . . . . . . . . . . 51

Using the StableSound

Selecting the optical audio output format . . . . . . . . . . . 52

Using the Dolby

feature. . . . . . . . . . . . . . . . . . . 52

Digital Dynamic Range Control

feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Using the Locks menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Entering the PIN code . . . . . . . . . . . . . . . . . . . . . . . . . . 52

If you cannot remember your PIN code. . . . . . . . . . . . . 53

Changing your PIN code . . . . . . . . . . . . . . . . . . . . . . . . 53

Blocking TV programs and movies

by rating (V-Chip). . . . . . . . . . . . . . . . . . . . . . . . . . 53

Downloading an additional rating system for blocking

TV programs and movies . . . . . . . . . . . . . . . . . . . . 54

Blocking channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Unlocking programs temporarily. . . . . . . . . . . . . . . . . . 55

Using the input lock feature. . . . . . . . . . . . . . . . . . . . . . 55

Using the GameTimer

. . . . . . . . . . . . . . . . . . . . . . . . . 55

Using the control panel lock feature . . . . . . . . . . . . . . . 56

Using the PC settings feature . . . . . . . . . . . . . . . . . . . . . . . . 56

Setting the PC Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Setting the sleep timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Using REGZA-LINK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

REGZA-LINK playback device (HD DVD player, etc.)

control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

REGZA-LINK input source selection . . . . . . . . . . . . . . 58

VOLUME and MUTE controls of Audio Receiver. . . . 58

Other REGZA-LINK functions . . . . . . . . . . . . . . . . . . . 58

Using the HDMI settings feature . . . . . . . . . . . . . . . . . . . . . 59

Displaying TV status information. . . . . . . . . . . . . . . . . . . . . 60

Understanding the auto power off feature . . . . . . . . . . . . . . 60

Understanding the last mode memory feature . . . . . . . . . . . 60

(continued)

Chapter 7: Using the TV’s advanced features . . . . . . . . . . . . .61

Using the advanced picture settings features . . . . . . . . . . . . 61

Using dynamic contrast . . . . . . . . . . . . . . . . . . . . . . . . . 61

Using the static gamma feature . . . . . . . . . . . . . . . . . . . 61

Selecting the color temperature . . . . . . . . . . . . . . . . . . . 61

Selecting the cinema mode (480i and 1080i signals). . . 62 Using the ClearFrame

Using the Film Stabilization feature . . . . . . . . . . . . . . . 62

Using CableClear

Using MPEG noise reduction. . . . . . . . . . . . . . . . . . . . . 63

Using the ColorMaster

™

feature . . . . . . . . . . . . . . . . . . . 62

digital noise reduction . . . . . . . . . . 62

™

feature . . . . . . . . . . . . . . . . . . 63

Using x.v.Color Selection feature . . . . . . . . . . . . . . . . . 64

Using the Game Mode feature . . . . . . . . . . . . . . . . . . . . 64

Using the advanced audio settings features . . . . . . . . . . . . . 64

Using the surround sound features. . . . . . . . . . . . . . . . . 64

Chapter 8: Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . .65

General troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

LED indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Chapter 9: Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Acceptable signal formats

for PC IN and HDMI terminals . . . . . . . . . . . . . . . . . . . 69

Limited United States Warranty

for LCD Televisions 26” and Larger . . . . . . . . . . . . . . . 70

Limited Canadian Warranty

for Toshiba Brand Flat Panel Televisions . . . . . . . . . . . 71

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73

Chapter 1: Introduction

Features of your new TV

The following are just a few of the many exciting features of your new Toshiba widescreen, integrated HD, LCD TV:

• Integrated digital tuning (8VSB ATSC and QAM)

eliminates the need for a separate digital converter set-top box (in most cases).

• 1080p output resolution.

• Four HDMI

interfaces with 1080p input support (- page 16).

• HDMI capabilities

Lip-Sync Latency feature activates an auto audio/video display timing adjustment function that allows HDMI source devices to accurately perform synchronization automatically.

Deep Color feature allows the HDMI source to increase the available colors bits within the boundaries defined by the RGB or YCbCr color space.

x.v.Color feature expands the acceptable color range (limits) in HDMI signals and allows for sending of wider color signals from HDMI.

• REGZA-LINK allows control of external devices from the

TV remote via HDMI connection (- page 57).

• Two sets of ColorStream

video inputs (- page 14).

• Digital Audio Out optical audio connection with Dolby

Digital optical output format (- page 52).

• CableClear

(- page 62).

• PC IN (Analog RGB) computer terminal (- page 19).

• Channel Labeling allows you to put the Call Letters (e.g.

ABC, HBO, etc.) on the screen along with the station numbers, so you always know what you’re watching (- page 38).

• IR OUT infrared terminal using the IR blaster cable for IR

pass-through device control (- pages 12 and 15).

• ColorMaster

colors. The menu for this feature has a unique “black” design to enhance contrast while you’re adjusting the color (- page 63).

• ClearFrame

• Channel Browser

all channels and inputs (- page 42).

• Favorites Browser allows you to easily navigate between

your favorite channels and inputs (- page 42).

• Channel Tuning Mode allows you to choose how tuning

will be handled for over-the-air analog and digital channels (- page 44).

• GameTimer

access (- page 55).

™

digital, high-definition multimedia

HD high-resolution component

digital picture noise reduction

™

allows you to adjust the TV’s standard

™

120Hz anti-blur feature (- page 62).

™

allows you to easily navigate between

allows you to set a time limit for input source

Overview of steps for installing, setting up, and using your new TV

Follow these steps to set up your TV and begin using its many exciting features.

1 Observe the following when choosing a location for the

TV:

• Read “Important notes about your LCD TV”

(- page 6).

• Place the TV in a proper location (- pages 2–5)

2 Do not plug in any power cords until AFTER you have

connected all cables and devices to your TV.

3 BEFORE connecting cables or devices to the TV, learn

the functions of the TV’s connections and controls (

- pages 10–11).

4 Connect your other electronic device(s) to the TV

(

- pages 12–19).

5 See “Chapter 3: Using the remote control” (- page 20)

for an overview of the buttons on the remote control, install the batteries and prepare to operate your other device(s).

6 AFTER connecting all cables and devices, plug in the

power cords for your TV and other devices.

Note: After you turn on the TV, the Menu Language selection and Demo Mode selection menus appear automatically by default. You can turn off the On-Screen demonstration mode by setting the Demo Mode to Off. (

- page 35).

7 See “Menu layout and navigation” for a quick overview of

navigating the TV’s menu system (

- page 33).

8 Program channels into the TV’s channel memory

(

- page 36).

9 For details on using the TV’s features, see Chapters 6

and 7.

10 For help, refer to the Troubleshooting Guide, see

Chapter 8.

11 For technical specifications and warranty information, see

Chapter 9.

Chapter 1: Introduction

TV front and side panel controls and connections

Model 42XV540U is used in this manual for illustration purposes.

TV front

1 Remote sensor — Point the remote control toward this

remote sensor.

Effective range:

16.4 ft (5m)

2 Green and Yellow LEDs

Green: See “LED indications” on page 67. Yellow = Power-On Mode indicator (- “Selecting the

Power-On Mode” on page 40) See “LED indications” on page 67 for additional

information.

3 VIDEO-2 IN — The side panel A/V connections are

referred to as “VIDEO 2” and include standard A/V connections.

4 POWER — Press to turn the TV on and off.

If the TV stops responding to the controls on the remote control or TV control panel and you cannot turn off the TV, press and hold the POWER button on the TV control panel for 5 or more seconds to reset the TV.

Right side panel

Control panel

5 ARROWS BbC c — When a menu is on-screen, these

buttons function as up/down/left/right menu navigation buttons.

6 MENU (ENTER) — Press to access the menu system

(- page 33). When a menu is on-screen, the MENU button on the TV’s control panel functions as the ENTER button.

7 EXIT — Press to instantly close an on-screen menu.

8 CHANNEL Bb — When no menu is on-screen, these

buttons change the channel (programmed channels only;

- page 36).

9 VOLUME C c — These buttons adjust the volume level.

10 INPUT — Repeatedly press to change the source you are

viewing (ANT/CABLE, VIDEO 1, VIDEO 2, ColorStream HD1, ColorStream HD2, HDMI 1, HDMI 2, HDMI 3, HDMI 4, PC).

11 HDMI

12 Service port — For service use only. Used for updating

™

IN — High-Definition Multimedia Interface

(HDMI 4) input receives digital audio and uncompressed digital video from an HDMI device or uncompressed digital video from a DVI device. HDMI connection is necessary to receive 1080p signals.

the television’s firmware.

Chapter 1: Introduction

TV back panel connections

For an explanation of cable types and connections, see pages 12–19.

1 DIGITAL AUDIO OUT — Optical audio output in Dolby

Digital or PCM (pulse-code modulation) format for connecting an external Dolby Digital decoder, amplifier, A/V receiver, or home theater system with optical audio input.

2 HDMI

3 PC IN — For use when connecting a personal computer.

4 PC/HDMI 1 (AUDIO) IN — PC audio input terminal is

5 COLORSTREAM HD1 and COLORSTREAM HD2

™

IN — High-Definition Multimedia Interface

input receives digital audio and uncompressed digital video from an HDMI device or uncompressed digital video from a DVI device. HDMI connection is necessary to receive 1080p signals.

shared with HDMI 1 analog audio input terminal, and its use can be configured in the Audio Setup menu (- page 57).

— Two sets of ColorStream

high-definition component video inputs (with standard stereo audio inputs) for connecting devices with component video output, such as a Toshiba DVD player with ColorStream

Note: Component video cables carry only video information; separate audio cables are required for a complete connection.

TV back

Power cord

Cable Strap

6 VIDEO 1 IN — Standard (composite) video and standard

audio inputs plus optional S-video inputs for connecting devices with composite video or S-video output.

Note: Standard (composite) video and S-video cables carry only video information; separate audio cables are required for a complete connection.

7 FIXED AUDIO OUT — Analog audio outputs for

connecting an audio amplifier.

8 IR OUT — For controlling infrared remote-controlled

devices through the TV. You can connect up to two devices with an optical IR blaster cable (- page 12), and then control the devices using the TV’s IR pass-through features.

9 ANT/CABLE — RF input that supports analog (NTSC)

and digital (ATSC) off-air antenna signals and analog and digital Cable TV (QAM) signals.

HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

Chapter 2: Connecting your TV

Overview of cable types

Cables can be purchased from most stores that sell audio/video devices. Before purchasing any cables, be sure of connector types required by your devices and the length of each cable.

Coaxial (F-type) cable

Coaxial (F-type) cable is used for connecting your antenna, cable TV service, and/or cable converter box to the ANT/ CABLE input on your TV.

Standard A/V cables (red/white/yellow)

Standard A/V cables (composite video) usually come in sets of three, and are for use with video devices with analog audio and composite video output. These cables (and the related inputs on your TV) are typically color-coded according to use: yellow for video, red for stereo right audio, and white for stereo left (or mono) audio.

HDMI™ cable (with HDMI Logo “ ”)

HDMI (High-Definition Multimedia Interface) cable is for use with devices with an HDMI output. An HDMI cable delivers digital audio and video in its native format. This cable carries both video and audio information; therefore, separate audio cables are not required for a complete HDMI device connection (- pages 16, 17 and 19).

Note: HDMI cable provides better picture performance than a standard (composite) video or S-video cable.

Dual-wand IR blaster cable

Dual-wand IR blaster cable is for use with video devices with IR (infrared) remote control. This cable can be used with the TV’s IR pass-through feature (- page 15).

To obtain IR blaster cable:

Visit http://ceaccessories.toshiba.com/

Optical audio cable

S-video cable

S-video cable is for use with video devices with S-video output. Separate audio cables are required for a complete connection.

Note: An S-video cable provides better picture performance than a composite video cable. If you connect an S-video cable, be sure to disconnect the standard (composite) video cable or the picture performance will be unacceptable.

Component video cables (red/green/blue)

Component video cables come in sets of three and are for use with video devices with component video output. (ColorStream cables are typically color-coded red, green, and blue. Separate audio cables are required for a complete connection.

Note: Component video cables provide better picture performance than a standard (composite) video or S-video cable.

is Toshiba’s brand of component video.) These

Optical audio cable is for connecting receivers with Dolby Digital or PCM (pulse-code modulation) optical audio input to the TV’s DIGITAL AUDIO OUT terminal (- page 18).

Analog RGB (15-pin) computer cable

Analog RGB (15-pin) computer cable is for connecting a PC to the TV’s PC IN terminal (- page 19).

Note: Separate audio cables are required for a complete connection.

About the connection illustrations

You can connect different types and brands of devices to your TV in several different configurations. The connection illustrations in this manual are representative of typical device connections only. The input/output terminals on your devices may differ from those illustrated herein. For details on connecting and using your specific devices, refer to each device’s owner’s manual.

Chapter 2: Connecting your TV

Connecting a VCR (or a VCR with S-video) and antenna, Cable TV or Camcorder

Camcorder

VIDEO

AUDIO

OUT

VIDEO 2 inputs on TV right side panel

TV upper back panel

TV lower back panel

You will need:

• coaxial cables

• standard A/V cables

– For better picture performance, if your VCR has S-video,

use an S-video cable (plus the audio cables) instead of the standard video cable.

– For better picture performance, if your camcorder has

S-video, connect an S-video cable (plus the audio cables) to VIDEO 1 on the TV back instead of the VIDEO 2 on the TV right side panel.

– If you have a mono VCR, connect L/MONO on the TV to

your VCR’s audio out terminal using the white audio cable only.

•

S-video cable (if your VCR or camcorder has S-video)

– Do not connect both types of video cable to VIDEO 1 at

the same time or the picture performance will be unacceptable.

•

standard audio cables (if your VCR or camcorder has S-video)

Note: When you use a Cable box, you may not be able to use the remote control to program or access certain features on the TV.

S-video cable

Standard A/V cable

From Cable TV or antenna

Stereo VCR

VIDEO AUDIO

CH 3 CH 4

OUT

From Cable TV

Cable box

CH 3 CH 4

OUT

IN from ANT

OUT

Audio cable

To view the antenna or Cable signal:

Select the ANT/CABLE video input source on the TV.*

To view basic and premium Cable channels:

Turn OFF the VCR. Select the ANT/CABLE video input source on the TV.* Tune the TV to channel 3 or 4 (whichever channel the Cable box output is set to). Use the Cable box controls to change channels.

To view the VCR:

Turn ON the VCR. Select the VIDEO 1 video input source on the TV.*

To view the camcorder video:

Select the VIDEO 2 video input source on the TV.*

* To select the video input source, press INPUT on the remote control

(- page 21). To program the TV remote control to operate other devices, see Chapter 3.

The unauthorized recording, use, distribution, or revision of television programs, videotapes, DVDs, and other materials is prohibited under the Copyright Laws of the United States and other countries, and may subject you to civil and criminal liability.

Chapter 2: Connecting your TV

Connecting a DVD player with ColorStream® (component video), a VCR, and a satellite receiver

Your TV has two sets of ColorStream® (component video) inputs.

AUDIO

OUT

COMPONENT VIDEO

VIDEO

S-VIDEO

OUT

DVD player with component video

From satellite dish

AUDIO

OUT

Satellite

COMPONENT VIDEO

VIDEO

S-VIDEO

OUT

Satellite receiver with component video

You will need:

• coaxial cables

• standard A/V cables

– For better picture performance, if your VCR has S-video,

use an S-video cable (plus the audio cables) instead of the standard video cable. Do not connect both types of video cable to VIDEO 1 at the same time or the picture performance will be unacceptable.

– If you have a mono VCR, connect L/MONO on the TV to

your VCR’s audio out terminal using the white audio cable only.

•

standard audio cables

• component video cables

– You can connect the component video cables (plus audio

cables) from the DVD player or satellite receiver to either set of ColorStream terminals on the TV (HD1 or HD2). The ColorStream HD1 and HD2 terminals can be used to display Progressive (480p, 720p) and Interlaced (480i, 1080i). Please check the Owner’s Manual of the DVD player or satellite in order to determine the best output signal available (1080p is not supported).

– If your DVD player or satellite receiver does not have

component video, connect a standard A/V cable to VIDEO 2 on the side panel. If your DVD player has HDMI video, see page 16.

TV upper back panel

TV lower back panel

To view satellite programs using the component video connections:

Turn on the satellite receiver. Select the ColorStream HD2 video input source on the TV.*

To view the VCR or view and record antenna channels:

Turn ON the VCR. Tune the VCR to the channel you want to watch. Select the VIDEO 1 video input source on the TV.*

To record a TV program while watching a DVD:

Turn ON the VCR. Tune the VCR to the channel to record. Select the ColorStream HD1 video input source on the TV* to view the DVD.

* To select the video input source, press INPUT on the remote control

(- page 21). To program the TV remote control to operate other devices, see Chapter 3.

Stereo VCR

VIDEO AUDIO

OUT

From antenn

IN from ANT

CH 3 CH 4

OUT to TV

To view antenna or Cable channels:

Select the ANT/CABLE video input source on the TV.*

To view the DVD player:

Turn ON the DVD player. Select the ColorStream HD1 video input source on the TV.*

Chapter 2: Connecting your TV

Connecting a device to the IR OUT infrared terminal using the IR blaster cable for IR pass-through device control

You can use the TV’s IR OUT terminal (infrared passthrough) to remotely operate (through the TV) many infrared remote-controlled devices (such as Toshiba infrared remotecontrolled VCRs or DVD players) enclosed within an entertainment center or similar cabinet. Without the IR OUT connection, the device typically would need to be visible to operate it remotely.

You will need:

• dual-wand IR blaster cable (- page 12)

• other audio/video cables as required to connect the device(s)

to the TV (- pages 13–17)

Front of IR-controlled DVD player (for example)

To connect the IR blaster cable:

1 Locate the infrared sensor on the front of your device.

This sensor is marked on some devices.*

2 Align one of the IR blaster cable’s wands about 1 inch

away from the infrared sensor on the front of the device and attach it using double-sided mounting tape. If you have a second device, attach the second wand in a similar manner. (See illustration.)

Note: If you do not have a second device, coil the second wand with a rubber band and leave it behind the TV.

3 Plug the IR blaster cable’s plug into the TV’s IR OUT

terminal.

To control the device(s):

Point either the device’s remote control or the TV remote control (that you previously programmed to operate the device; - Chapter 3) toward the front of the TV and press the button for the desired function. The signal passes from the remote control through the TV to the device via the IR blaster cable.

Front of IR-controlled audio device (for example)

Infrared sensor

IR blaster cable wand (approx.1 inch from device)

TV upper back panel

Note:

• If you use the device’s remote control to operate the device, you also will need to use the TV’s remote control to operate the TV.

• The IR pass-through feature does not support all IR-controlled devices; satisfactory performance may not be attainable with certain devices.

*If you cannot locate the device’s infrared sensor:

1 Turn OFF the device. 2 Starting at the lower left corner of the device, place the

end of the device’s remote control (with the infrared emitter) so it touches the front of the device and press POWER. (Do not use the TV’s remote control for this step.)

3 If the device turns on, the point at which the remote

control touched the device is the location of the sensor.

4 If the device does not turn on, move the remote control

slightly to the right and press POWER again.

5 Repeat step 4 until you locate the device’s infrared

sensor.

Chapter 2: Connecting your TV

Connecting an HDMI™ or DVI device to the HDMI input

The HDMI input on your TV receives digital audio and uncompressed digital video from an HDMI source device, or uncompressed digital video from a DVI (Digital Visual Interface) source device.

This input is designed to accept HDCP (High-Bandwidth Digital-Content Protection) program material in digital form from EIA/CEA-861-D–compliant devices (such as a set-top box or DVD player with HDMI or DVI output).

The HDMI input can accept and display VGA, SVGA, XGA, WXGA, SXGA, 480i (60Hz), 480p (60Hz), 720p (60Hz), 1080i (60Hz), and 1080p (24Hz/60Hz) signal formats. For detailed signal specifications, see page 69.

Supported Audio format: Linear PCM, sampling rate 32/44.1/ 48 kHz

Note:

• To connect a PC to the HDMI input, see page 19.

• Some of legacy HDMI sources may not work properly with

your latest HDMI TV, due to new standard adoption. Please try setting the following three options (Lip-Sync Latency, Deep Color, x.v.Color) to Off. Your legacy HDMI source should operate properly with your TV. See page 69.

• Supported Audio format : Linear PCM, sampling rate 32/

44.1/48kHz

To connect an HDMI device, you will need:

• one HDMI cable (type A connector) per HDMI device

– For proper operation, it is recommended that you use an

HDMI cable with the HDMI Logo ( ).

– To display an 1080p/60Hz signal format, you will need a

High Speed HDMI cable. Conventional HDMI/DVI cable may not work properly.

– HDMI cable transfers both video and audio. Separate

analog audio cables are not required (see illustration).

– See “Setting the HDMI™ audio mode” (- page 39).

[1]

consumer electronic

* To select the video input source, press INPUT on the remote control

(- page 21). To program the TV remote control to operate other devices, see Chapter 3.

To connect a DVI device, you will need:

• one HDMI-to-DVI adapter cable (HDMI type A connector)

per DVI device

– For proper operation, the length of an HDMI-to-DVI

adapter cable should not exceed 9.8 ft (3m). The recommended length is 6.6 ft (2m).

•

one pair of standard analog audio cables per DVI device

– An HDMI-to-DVI adapter cable transfers video only.

Separate analog audio cables are required (see illustration).

– See “Setting the HDMI™ audio mode” (- page 39).

TV upper back panel

DVI device

VIDEO AUDIO

OUT

Note: To ensure that the HDMI or DVI device is reset properly, it is recommended that you follow these procedures:

• When turning on your electronic components, turn on the TV first, and then the HDMI or DVI device.

• When turning off your electronic components, turn off the HDMI or DVI device first, and then the TV.

DVI/ HDCP

OUT

TV upper back panel TV right side panel

HDMI device

VIDEO AUDIO

OUT

HDMI OUT

To view the HDMI device video:

Select the HDMI 1, HDMI 2, HDMI 3, or HDMI 4 video input source on the TV.*

[1] EIA/CEA-861-D compliance covers the transmission of

uncompressed digital video with high-bandwidth digital content protection, which is being standardized for reception of highdefinition video signals. Because this is an evolving technology, it is possible that some devices may not operate properly with the TV.

HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

Chapter 2: Connecting your TV

REGZA-LINK connection

You can control the basic functions of connected audio/video devices using the TV’s remote control if you connect a REGZA-LINK compatible audio receiver or playback device. For an explanation of setup and operations, see pages 57 and 58.

TV upper back panel TV right side panel

Playback device (REGZA-LINK HD DVD player,etc.)

VIDEO

AUDIO

OUT

HDMI OUT

VIDEO

AUDIO

OUT

Audio receiver

HDMI OUTHDMI

Playback device (REGZA-LINK HD DVD player,etc.)

VIDEO

AUDIO

OUT

HDMI OUT

To connect an Audio Receiver and Playback Devices, you will need:

• HDMI cables (- page 16)

Note:

• If several devices are connected, REGZA-LINK feature may not operate properly.

• For proper operation, it is recommended that you use HDMI cables with the HDMI Logo ( ).

Before controlling the device(s):

• After completing the above connections, set the REGZA-

LINK Setup menu as you desire (- page 59).

• The connected devices must also be set. For details, see the

operation manual for each device.

• The REGZA-LINK feature uses the CEC technology as

regulated by the HDMI standard.

• This feature is limited to models incorporating Toshiba’s

REGZA-LINK. However, Toshiba is not liable for those operations. Refer to the individual instruction manuals for compatibility information.

Chapter 2: Connecting your TV

Connecting a digital audio system

The TV’s DIGITAL AUDIO OUT terminal outputs a Dolby®* Digital g or 2-channel down-mixed PCM (pulse-code modulation) signal for use with an external Dolby decoder or other external audio system with optical audio input.

You will need:

• optical audio cable (Use an optical audio cable that has the

larger “TosLink” connector and not the smaller “minioptical” connector.)

Digital

Note:

• Some audio systems may not be compatible with Dolby Digital bitstream signals. Older audio systems that are not compatible with standard optical out signals may not work properly, creating a high noise level that may damage speakers or headphones. THIS DAMAGE IS NOT COVERED BY YOUR WARRANTY.

• The DIGITAL AUDIO OUT terminal may not output some digital audio sources because of copy restrictions.

* Manufactured under license from Dolby Laboratories.

“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

Dolby Digital decoder or other digital audio system

Optical Audio IN

TV upper back panel

LINE IN LR

To control the audio:

1 Turn on the TV and the digital audio device. 2 Press Y on the TV’s remote control and open the

Audio menu.

3 Highlight Audio Setup and press T.

Audio

Digital Audio Selector

Audio Settings

Advanced Audio Settings

Audio Setup

4 In the Optical Output Format field, select either

Dolby Digital or PCM, depending on your device

(

- “Selecting the optical audio output format” on

page 52).

Audio Setup

PC Audio No

HDMI 1 Audio

MTS Stereo

Language

Optical Output Format

Dolby Digital Dynamic Range Control

Reset

Auto

English

Dolby Digital

Compressed

Done

Connecting an audio system

This connection allows you to use external speakers with an external analog audio amplifier to adjust the sound level.

You will need:

• standard audio cables

Analog audio amplifier

LINE IN LR

TV upper back panel

To control the audio:

1 Turn on the TV and the stereo amplifier. 2 Minimize the sound volume from the TV’s built-in

speakers and control the volume level using the amplifier’s remote control.

Chapter 2: Connecting your TV

Connecting a personal computer (PC)

With either the PC IN or HDMI connection, you can watch your computer’s display on the TV and hear the sound from the TV’s speakers.

To connect a PC to the PC IN terminal on the TV:

When connecting a PC to the PC IN terminal on the TV, use an analog RGB (15-pin) computer cable and a PC audio cable.

TV upper back panel

•

Signal names for mini D-sub 15-pin connector

Pin No.

1R 6Ground11NC

2G 7Ground12NC

3 B 8 Ground 13 H-sync

4 NC * 9 NC 14 V-sync

5 NC 10Ground15NC

*NC=Not connected

Signal name

Pin No.

Signal name

Pin No.

Signal name

To connect a PC to the HDMI terminal on the TV:

When connecting a PC to the HDMI terminal on the TV, use an HDMI-to-DV1 adapter cable and an analog audio cable.

If connecting a PC with an HDMI terminal, use an HDMI cable (type A connector). Separate PC audio cable is not necessary (- page 16).

TV upper back panel

PC audio cable

Computer

PC audio output

Conversion adapter (if necessary)

• To use a PC, set the monitor output resolution on the PC

before connecting it to the TV. The PC IN terminal can accept and display VGA, SVGA, XGA, WXGA, and SXGA signal formats. For detailed signal specifications, see page

69.

• To display the optimum picture, use the PC setting feature

(

- “Using the PC settings feature” on page 56).

Note:

• The PC audio input terminal on the TV is shared with the

HDMI 1 analog audio input terminal (- page 57).

• Some PC models cannot be connected to this TV.

• An adapter is not needed for computers with a compatible

mini D-sub15-pin terminal.

• Depending on the DVD’s title and the specifications of the PC on which you are playing the DVD-Video, some scenes may be skipped or you may not be able to pause during multi-angle scenes.

PC audio cable

Computer

PC audio output

Note:

• The edges of the images may be hidden.

• If receiving a 480i (HDMI), 480p (HDMI), 720p, 1080i, or

1080p signal program, Native mode scales the video to display the entire picture within the borders of the screen (i.e. no overscanning).

Chapter 3: Using the remote control

Preparing the remote control for use

Your TV remote control can operate your TV and many other devices such as cable converter boxes, satellite receivers, VCRs, DVD players, and HTIBs (home theater in a box), even if they are different brands.

If you have a Toshiba device:

Your TV remote control is preprogrammed to operate most Toshiba devices (- page 24).

If you have a non-Toshiba device or a Toshiba device that the remote control is not preprogrammed to operate:

You can program the TV remote control so it will operate the other device (- pages 22–32).

Installing the remote control batteries

1 Slide the battery cover off the back of the remote control.

2 Install two “AA” size alkaline batteries. Match the + and

– symbols on the batteries to the symbols on the battery compartment.

3 Slide the battery cover on to the remote control until the

lock snaps.

Caution: Batteries must not be exposed to excessive heat such as sunshine, fire or the like.

Note:

• Be sure to use AA size alkaline batteries.

• Dispose of batteries in a designated disposal area.

• Batteries should always be disposed of with the

environment in mind. Always dispose of batteries in accordance with applicable laws and regulations.

• If the remote control does not operate correctly, or if the operating range becomes reduced, replace batteries with new ones.

• When necessary to replace batteries in the remote control, always replace both batteries with new ones. Never mix battery types or use new and used batteries in combination.

• Always remove batteries from the remote control if they are dead or if the remote control is not to be used for an extended period of time. This will prevent battery acid from leaking into the battery compartment.

Chapter 3: Using the remote control

Learning about the remote control

The buttons used for operating the TV only are described here. For the REGZA-LINK remote control functions, see the section “Using REGZA-LINK” (- page 57). For a complete list of the remote control’s functions, see the remote control functional key chart (- pages 22–23).

16 17

21 22

5 7

8, 11, 12

15 18

MODE SELECT

TV, CABLE/SAT, HD DVD, DVD TV

until the keypad blinks 3 times to control the TV. The selected MODE key blinks each time any key is pressed. (

page 24). When the Auto Input feature is set, these keys

can also be used to change inputs on the TV (

4 Channel Numbers (0–9, –/100) directly tune

channels. The = button is used to tune digital channels

(

- page 44) or to edit the Favorite List (- page 42).

5 INPUT selects the video input source (

6 FAV BROWSER accesses the Favorites List in the

Channel Browser

7 MENU accesses the main TV menu system (

and 34).

ENTER

9 THINC accesses the THINC menu (- page 33).

10 PAGE + / - are used for paging up and down in channel

lists.

11 3 C / # c While watching TV, these buttons open the

Channel Browser in the channel history (- page 43). (Also see “Arrow buttons.”)

12 Arrow buttons (BbC c) When a menu is on-screen,

these buttons select or adjust programming menus. (Also see 3 C / # c.)

13 VOL + - adjusts the volume level.

14 CH Bb cycles through programmed channels when no

menu is on-screen (

15 EXIT closes on-screen menus.

16 INFO displays TV status information as well as program

details, when available (- page 60).

17 MUTE reduces or turns off the sound (- page 50).

18 CH RTN returns to the last viewed channel or source

(- page 45).

activates highlighted items in the main menu system.

sets the five remote control device modes:

, and

VCR/PVR

- page 41).

™

(- page 42).

™

and tune to the previous/next channel

- page 36).

. Press

page 37).

- pages 33

Note: The error message “Not Available” may appear if you press a key for a function that is not available.

1 SLEEP accesses the sleep timer (- page 57).

2 POWER turns the TV on and off. When the TV is on, the

green LED indicator on the TV front will be illuminated.

19 RECALL displays TV status information (- page 60).

20 C.CAPTION opens the closed caption/audio selector

screen. (The audio selector is not available for analog channels.) (- page 49.)

21 PIC MODE selects the picture mode (- page 48).

22 FREEZE freezes the picture. Press again to restore the

moving picture.

23 PIC SIZE cycles through the picture sizes: Natural,

TheaterWide 1/2/3, Full, 4:3 HD, Native, and Dot by Dot (

- page 45).

Chapter 3: Using the remote control

Remote Control functional key chart

REMOTE CONTROL KEY

TV CABLE/SAT HD DVD DVD VCR/PVR

Toshiba TV CABLE

SAT (satellite)

HD DVD Player

HD DVD Recorder

DVD/VCR (Orion)

DVD Player/ Recorder

VCR (Toshiba)

PVR

SLEEP (TV) Sleep (TV) Sleep (TV) Sleep (TV) Sleep (TV) Sleep (TV) Sleep (TV) Sleep (TV) Sleep (TV) Sleep

MODE SELECT

Remote control device mode selection

POWER Power Power Power Power Power Power Power Power Power

1 Digit 1 Digit 1 Digit 1 Digit 1 Digit 1 Digit 1 Digit 1 Digit 1 Digit 1

2 Digit 2 Digit 2 Digit 2 Digit 2 Digit 2 Digit 2 Digit 2 Digit 2 Digit 2

3 Digit 3 Digit 3 Digit 3 Digit 3 Digit 3 Digit 3 Digit 3 Digit 3 Digit 3

4 Digit 4 Digit 4 Digit 4 Digit 4 Digit 4 Digit 4 Digit 4 Digit 4 Digit 4

5 Digit 5 Digit 5 Digit 5 Digit 5 Digit 5 Digit 5 Digit 5 Digit 5 Digit 5

6 Digit 6 Digit 6 Digit 6 Digit 6 Digit 6 Digit 6 Digit 6 Digit 6 Digit 6

7 Digit 7 Digit 7 Digit 7 Digit 7 Digit 7 Digit 7 Digit 7 Digit 7 Digit 7

8 Digit 8 Digit 8 Digit 8 Digit 8 Digit 8 Digit 8 Digit 8 Digit 8 Digit 8

9 Digit 9 Digit 9 Digit 9 Digit 9 Digit 9 Digit 9 Digit 9 Digit 9 Digit 9

0 Digit 0 Digit 0 Digit 0 Digit 0 Digit 0 Digit 0 Digit 0 Digit 0 Digit 0

100/-/+10

- (digital separator)

----- - (sub CH) 10 10

- (digital separator)

100 -----

INPUT (TV) Input (TV) Input (TV) Input (TV) Input (TV) Input (TV) Input (TV) Input (TV) Input (TV) Input

Menu select up

select down

Menu select up

Menu select down

Menu select up

Menu select down

Menu select up

Menu select down

Menu select up

Menu select down

Menu select up

Menu select down

Menu select up

Menu select down

-----

Menu select up

Menu select down

Menu select

C 3 # c

left/right/

3 Back

Menu select left/right

-----

Menu select left/right

# Next

ENTER Enter Enter

FAV BROWSER/ SETUP

MENU Menu

THINC/TOP MENU

GUIDE Guide

PAGE +/-

VOLB/b

CHB/b

EXIT/DVD CLEAR

MUTE Mute

FAV BROWSER

----- ----- DVD setup DVD setup DVD setup DVD setup ----- -----

Cable menu

THINC THINC THINC Top menu Top menu Top menu Top menu THINC THINC

Cable Guide

Page up/ down

Volume up/down

Channel up/down

Cable page up/down

Volume up/down

Channel up/down

Exit Exit Exit DVD clear DVD clear DVD clear DVD clear ---- Exit

Mute

Select/ Enter

Action, menu

EnterEnterEnterEnter----- Enter

DVD menu DVD menu DVD menu DVD menu ----- Menu

SAT Guide ---- ----

Guide page up/down

Volume up/down

Channel up/down

Mute

Page up/ down

(TV) Volume

up/down

----

(TV) Mute

DVD TV Guide

----

(TV) Volume up/down

Channel up/down

(TV) Mute

Guide page up/down

Volume up/down

DVD Channel up/down

Mute

DVD TV Guide

Guide page up/down

Volume

up/down

DVD Channel up/down

Mute

----- Guide

---- ----

Volume up/down

Channel up/down

Mute

Volume up/down

Channel up/down

Mute

INFO Guide Info Info Info Display Display Display Display ----- Info

RECALL

(TV) Display

Chapter 3: Using the remote control

REMOTE CONTROL KEY

CH RTN/ DVD RTN

PAUSE/ STEP

TV CABLE/SAT HD DVD DVD VCR/PVR

Toshiba TV CABLE

Last Channel

Pause

Last Channel

Cable Pause

SAT (satellite)

Last Channel

HD DVD Player

HD DVD Recorder

DVD/VCR (Orion)

DVD RTN DVD RTN DVD RTN DVD RTN ----- -----

SAT Pause Pause/Step Pause Pause Pause Pause Pause

DVD Player/ Recorder

VCR (Toshiba)

PVR

PLAY Play Cable Play SAT Play Play Play Play Play Play Play

STOP Stop Cable Stop SAT Stop Stop Stop Stop Stop Stop Stop

SKIP -

SKIP +

REW Rewind

Skip REW/ Day -

Skip FWD/ Day +

----- ----- Skip REW Skip REW Skip REW Skip REW ----- -----

----- ----- Skip FWD Skip FWD Skip FWD Skip FWD ----- -----

Cable Rewind

SAT Rewind

Rewind Rewind Rewind Rewind Rewind Rewind

FF FF Cable FF SAT FF Fast FWD Fast FWD FWD FWD FWD FWD

C.CAPTION/ TV/VCR

REC

RESUME PLAY

SLOW/DIR +

PIC MODE

FREEZE

PIC SIZE

DISC/AM/ FM

C.Caption ---- TV/SAT ---- ---- TV/VCR ---- TV/VCR Reverse

REC menu (Single click)

Cable Record (Double click)

SAT Record (Double click)

---- ---- ----

----

Resume Play

Record (Double click)

Resume Play

Record (Double click)

---- ---- ---- ----

DVD Record (Double

click)

Record (Double click)

Slow/Dir + ----- ----- Slow FWD Slow FWD Slow FWD Slow FWD Slow FWD Slow FWD

(TV) Picture mode

(TV) Freeze

(TV) Picture size

(TV) Picture mode

(TV) Freeze

(TV) Picture size

(TV) Picture mode

(TV) Freeze

(TV) Picture size

(TV) Picture mode

(TV) Freeze

(TV) Picture size

(TV) Picture mode

(TV) Freeze

(TV) Picture size

(TV) Picture mode

(TV) Freeze

(TV) Picture size

(TV) Picture mode

(TV) Freeze

(TV) Picture size

(TV) Picture mode

(TV) Freeze

(TV) Picture size

(TV) Picture mode

(TV) Freeze

(TV) Picture size

----- ----- ----- ---- ---- DVD/VCR ---- ----- Replay

Note:

• “---” = key does not send a signal in that remote control mode.

Volume will affect the TV by default. When the volume is unlocked, all the devices will have their own volume if their ID has volume data. See “Using the volume lock feature” (- page 25).

DVD : REC is only for DVD Recorder, no function is picked for DVD Player.

+ 51 hidden pages