Toshiba 52RV530U, 46RV530U, 42RV530U Owner’s Manual
@ 32 52RV530U EN.book Page I Wednesday, January 30, 2008 3:54 PM
TOSHIBA
CGZ/X
ForanoverviewofStepsforSettingupyournewTV,seepage9.
Note:Todisplaya HighDefinitionpictureltheTVmustbereceivinga
HighDefinitionsignal(suchasanover4he,airHighDefinitionTV
broadcast,a HighDefinitiondigitalcableprogram,eraHighDefinition
digitalsatelliteprogram);Fo!detai!s,pleasecontactyourTVantenna
installer,cableprovider,orsatelliteprovider.
RV530U (E/F) Web 213:276
@ 32 52RV530U EN.book Page 2 Wednesday, January 30 2008 3:54 PM
DearCustomer,
Thank you for purchasing this Toshiba LCD TV. This manual
will help you use the many exciting features of your new LCD
TV. Before operating your LCD TV, please read this manual
completely, and keep it nearby for future reference.
Safety Precautions
WARNING: TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
WARNING: TO REDUCE THE RiSK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK),
NO USER-SERViCEABLE PARTS iNSiDE, REFER
SERViCiNG TO QUALIFIED SERVICE PERSONNEL,
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage" within
the product's enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons,
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance,
WARNING
To prevent injury, this apparatus must be securely attached to
the floor/wall in accordance with the installation instructions.
See item 20 on page 3 and instructions on page 5.
WARNING:If you decide to wall mount this television,
always use a UL Listed wall bracket appropriate for the size
and weight of this television. The use of any wall bracket
other than a UL Listed wall bracket appropriate for the size
and weight of this television for wall mounting this television
could result in serious bodily injury and/or property damage.
See "Removing the Pedestal Stand" (_ page 5).
NOTETOCATVINSTALLERS
This is a reminder to call the CATV system installer's attention
to Article 820-40 of the U.S. NEC, which provides guidelines for
proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the
building, as close to the point of cable entry as practical. For
additional antenna grounding information, see items 27 and 28
on page 4.
Congratulationsonyourpurchase!Asyouenjoyyour
newproduct,pleasekeepthesesafetytipsin mind:
The issue
• The home theater entertainment experience isa growing trend
and larger flat paneldisplays are popular purchases. However,
flat panel displays are not always supported on the proper stands
or installed according to the manufacturer's recommendations.
• Flat paneldisplays that are
inappropriately situated on dressers,
bookcases,shelves, desks,
speakers,chests or carts mayfall
overand cause injury.
TOSHIBACares!
Theconsumer electronics industry
is committed to making home
entertainment enjoyable and safe.
Tuneinto Safety
• OnesizedoesNOTfit all. Followthemanufacturer'srecommendations
forthe safeinstallationanduseof yourflat paneldisplay.
• Carefully readand understand all enclosed instructions for
proper use of this product.
• Don't allow children to climb on or play with furniture and
television sets.
• Don't placeflat panel displays on
furniture that can easilybe usedas
steps, such asa chest of drawers.
• Rememberthat children can
becomeexcited while watching a
program, especially on a "larger
than life" flat panel display. Care
should be takento placeor install
the displaywhere it cannot be
pushed,pulled over,or knockeddown.
• Careshould betaken to route all cords and
cables connectedto the flat paneldisplay sothat they cannot be
pulledor grabbedby curious children.
Wall Mounting: if youdecideto wall mountyour
flat panel display,always:
• Usea mount that has beenrecommended bythe display
manufacturer and/or listed byan independent laboratory (such
as UL, CSA,ETL).
• Follow all instructions supplied bythe display and wall mount
manufacturers.
• If you have any doubts about your ability to safely install your
flat panel display, contact your retailerabout professional
installation.
• Make surethat the wall where you aremounting the display is
appropriate. Some wall mounts are not designedto be mounted
to walls with steel studs or old cinder block construction, if you
are unsure, contacta professional
installer.
• A minimum of two peopleare
requiredfor installation. Flatpanel ..........,................
displays canbe heavy, www.CE.org/safety
RV530U (E/F) Web 213:276
@ 32 52RV530U EN.book Page 3 Wednesday, January 30 2008 3:54 PM
Important Safety Instructions
1
Read these instructions.
2
Keep these instructions.
3
Heed all warnings.
4
Follow all instructions.
5
Do not use this apparatus near water.
6
Clean only with dry cloth.
7
Do not block any ventilation openings. Install in
accordance with the manufacturer's instructions.
8) Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9) Do not defeat the safety purpose of Wideblade
the polarized or grounding type
plug. A polarized plug has two blades
with one wider than the other.
A grounding type plug has two blades
and a third grounding prong. The wide blade or the third
prong are provided for your safety. If the provided plug
does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being walked
on or pinched, particularly at plugs,
convenience receptacles, and the point
where they exit from the apparatus.
11) Only use attachments/accessories specified by the
manufacturer.
12) Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the
apparatus. When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or
when unused for long periods of time.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been
dropped.
Additional Safety Precautions
14a) CAUTION: If the TV is dropped and the cabinet or
enclosure surface has been damaged or the TV does not
operate normally, take the following precautions:
• ALWAYS turn off the TV and unplug the power cord to
avoid possible electric shock or fire.
• NEVER allow your body to come in contact with any
broken glass or liquid from the damaged television. The
LCD panel inside the TV contains glass and a toxic
liquid. If the liquid comes in contact with your mouth or
eyes, or your skin is cut by broken glass, rinse the
affected area thoroughly with water and consult your
doctor.
• ALWAYS contact a service technician to inspect the TV
any time it has been damaged or dropped.
CAUTION:
15)
• To reduce the risk of electric shock, do not use the
polarized plug with an extension cord, receptacle, or
other outlet unless the blades can be inserted
completely to prevent blade exposure.
• To prevent electric shock, match wide blade of plug to
wide slot; fully insert.
WARNING:
16)
To prevent the spread of fire, keep candles or other open
flames away from this product at all times.
Installation, Care, and Service
Installation
Follow these recommendations and precautions and heed all
warnings when installing your TV:
17) Never modify this equipment. Changes or modifications
may void: a) the warranty, and b) the user's authority to
operate this equipment under the rules of the Federal
Communications Commission.
18)
Never placethe TV on an unstable cart,
stand, or table. The TV may fall, causing
serious personalinjury, death,or serious
damage to the TV.
19) To avoid damage to this product, never place or store the
TV in direct sunlight; hot, humid areas; or areas subject to
excessive dust or vibration.
20) Always place the TV on the floor or a sturdy, level, stable
surface that can support the weight ofthe unit. To secure the
TV, use a sturdy strap from the hooks on the rear of the TV
pedestal to a wall stud, pillar, or other immovable structure.
Make sure the strap is tight, secure, and parallel to the floor.
21) The apparatus shall not be exposed to dripping or
splashing and that no objects filled with liquids, such as
vases, shall be placed on the apparatus.
22) Never block or cover the slots or openings in the TV
cabinet back, bottom, and sides. Never place the TV:
• on a bed, sofa, rug, or similar
i too close to drapes, curtains, or
The slots and openings are provided to protect the TV from
overheating and to help maintain reliable operation of the
TV. Leave a space of at least 4 (four) inches around the TV.
DANGER: RISK OF
SERIOUS PERSONAL
INJURY, DEATH, OR
EQUIPMENT DAMAGE!
4" Sturdy strap (as short as possible)
j Securement
Clip
TVside TVtop
surface;
walls; or
in a confined space such as a
bookcase, built-in cabinet, or __ _010
any other place with poor
ventilation.
(cotTtitTued)
3
RV530U (E/F) Web 213:276
@ 32 52RV530U EN.book Page 4 Wednesday, January 30 2008 3:54 PM
23) Always place the back of the television at least four (4)
inches away from any vertical surface (such as a wall) to
allow proper ventilation.
24) Never allow anything to rest on or roll over the power cord,
and never place the TV where the power cord is subject to
wear or abuse.
25) Never overload wall outlets and extension cords.
26) Always operate this equipment from a 120 VAC, 60 Hz
power source only.
27) Always make sure the antenna system is properly
grounded to provide adequate protection against voltage
surges and built-up static charges (see Section 810 of the
National Electric Code).
Antennalead-in wire
Antennadischarge unit
J Groundclamp
J
Electric service equipment
L
Groundclamps
28)
DANGER: RISK OF SERIOUS
(NECSection 810-20)
Groundingconductors
(NECSection 810-21)
/J"
Powerservicegrounding
electrode system (NECArt 250 Part-H)
PERSONAL INJURY OR DEATH!
• Use extreme care to make sure you are never in a
position where your body (or any item you are in contact
with, such as a ladder or screwdriver) can accidentally
touch overhead power lines. Never locate the antenna
near overhead power lines or other electrical circuits.
• Never attempt to install any of the following during
lightning activity: a) an antenna system; or b) cables,
wires, or any home theater component connected to an
antenna or phone system.
Care
For
better performance and safer operation of your TOSHIBA
TV,
follow these recommendations and precautions:
29)
If you use the TV in a room whose temperature is 32 °F
(0 °C) or below, the picture brightness may vary until the
LCD warms up. This is not a sign of malfunction.
30)
Always unplug the TV before
cleaning. Gently wipe the
display panel surface (the TV
screen) using a dry, soft cloth
only (cotton, flannel, etc.). A
hard cloth may damage the
surface of the panel. Avoid
contact with alcohol, thinner, benzene, acidic or alkaline
solvent cleaners, abrasive cleaners, or chemical cloths,
which may damage the surface. Never spray volatile
compounds such as insecticide on the cabinet. Such
products may damage or discolor the cabinet.
31)
WARNING:
RISK OF ELECTRIC SHOCK!
Never spill liquids or push objects of any kind into the TV
cabinet slots.
32)
While it is thundering, do not touch the connecting cables
or apparatus.
33)
For added protection of your TV from lightning and power
surges, always unplug the power cord and disconnect the
antenna from the TV if you leave the TV unattended or
unused for long periods of time.
34)
During normal use, the TV may make occasional snapping
or popping sounds. This is normal, especially when the
unit is being turned on or off. If these sounds become
frequent or continuous, unplug the power cord and contact
a Toshiba Authorized Service Center.
35)
WARNING: RISK OF
SERIOUS PERSONAL
INJURY OR EQUIPMENT
DAMAGE!
Never strike the screen with a sharp
or heavy object.
36) •
The LCD screen of this product can be damaged by
ultraviolet radiation from the sun. When selecting a
location for the television, avoid locations where the
screen may be exposed to direct sunlight, such as in
front of a window.
Never touch, press, or place anything on the LCD
screen. These actions will damage the LCD screen. If
you need to clean the LCD screen, follow the
instructions in item 30 on this page.
Service
37)
Never attempt to service the TV yourself. Opening and
removing the covers may expose you to dangerous
voltage or other hazards. Failure to follow this WARNING
may result in death or serious injury. Refer all servicing not
specified in this manual to a Toshiba Authorized Service
Center.
38)
Ifyou have the TV serviced:
• Ask the service technician to use only replacement
parts specified by the manufacturer.
• Upon completion of service, ask the service technician
to perform routine safety checks to determine that the
TV is in safe operating condition.
39)
The cold cathode fluorescent lamp in the LCD panel
contains a small amount of mercury.
When the TV reaches the end of its useful life, dispose of
the used TV by the approved method for your area, or ask
a qualified service technician to properly dispose of the
TV.
Note: The lamp(s) inside this product contain
mercury. Disposal may be regulated due to
environmental considerations. For disposal or
recycling information, contact your local authorities or the
Electronics Industries Alliance (www. eiae.org).
WARNING:
RISK OF ELECTRIC SHOCKt
RV530U (E/F) Web 213:276
@ 32 52RV530U EN.book Page 5 Wednesday, January 30 2008 3:54 PM
Choosinga location for yourLCDTV
To DisplayyourLCDTV on the included Pedestal
Stand:
Observe the following safety precautions:
1 Read and Follow the pedestal assembly instructions included
with the pedestal.
CAUTION: Before beginning pedestal assembly, carefully lay
the front of the LCD Panel face down on a flat, cushioned
surface such as a quilt or blanket. Leave the bottom of the unit
protruding over the edge of the surface and assemble the
pedestal as indicated below.
Note: Extreme care should always be used when attaching
the pedestal stand to avoid damage to the LCD par?el.
2)
Place the TV on a sturdy, level surface that can support the
weight of the TV.
3)
Be sure to secure the TV to a wall stud, pillar, surface, or other
immovable structure. To secure the TV in this manner: (1)
attach the provided securement clip to an immovable structure,
then (2) pass a sturdy strap through the securement clip and
attach each end to the hooks located on the back of the TV. Be
sure to leave at least 4 inches between the TV and the wall or
similar structure for ventilation. See item 20, page 3 for
additional details.
To DisplayyourLCDTV using a Wall Bracket:
If you decide to wall mount your LCD TV, always use a UL-
listed wall bracket appropriate for the size and weight of the
LCD TV (_ page 2) :
l) CAUTION: Two people are required for installation.
2) Unplug and remove any cables and/or other component
connectors from the rear of the TV.
3) Follow the instructions provided with your wall bracket.
Before proceeding, make sure the appropriate bracket(s) are
attached to the wall and the back of the TV as described in the
instructions provided with the wall bracket.
4) After attaching the appropriate bracket(s) to the wall and the
back of the TV, remove the pedestal stand from the TV as
described below.
Removingthe Pedestal Stand
1 Carefully lay the front of the unit face down on a flat,
cushioned surface such as a quilt or blanket. Leave the stand
protruding over the edge of the surface.
Note: Extreme care should always be used when removing
the pedestal stand to avoid damage to the LCD panel.
2) Remove the.jack pack cover on the back of the TV to expose
the pedestal stand screws. The .jack pack cover can be removed
without tools.
3) Remove the four screws shown in the diagram below. This will
allow removal of the pedestal stand.
4) Once you have removed all four screws holding the pedestal
stand in place, remove the pedestal stand from the TV by
sliding the pedestal stand away from the TV.
Fou r screws
RV530U (ELF) Web 213:276
@ 32 52RV530U EN.book Page 6 Wednesday, January 30 2008 3:54 PM
m
FCgDeclaration of gonformity
gompliance Statement
(Fart15):
The Toshiba 32RV530U, 37RV530U, 42RV530U, 46RV530U,
and 52RV530U Televisions comply with Part 15of the FCC
rules.
Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that
may cause undesired operation.
The party responsible for compliance to these rules is:
Toshiba America Consumer Products, L.L.C.
82 Totowa Rd. Wayne, NJ 07470.
Ph: 1-800-631-3811
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15
of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
removing and applying power to the equipment, the user is
encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
Caution: Changes or modifications to this equipment not
expressly approved by Toshiba could void the user's authority
to operate this equipment.
important notes about your £gO
The following symptoms are technical limitations of LCD
Display technology and are not an indication of malfunction;
therefore, Toshiba is not responsible for perceived issues
resulting from these symptoms.
1) An afterimage (ghost) may appear on the screen if a fixed, non-
moving image is displayed for a long period of time. The
afterimage is not permanent and will disappear in a short period
of time.
2) The LCD panel contained in this TV is manufactured using an
extremely high level of precision technology; however, there
may be an occasional pixel (dot of light) that does not operate
properly (does not light, remains constantly lit, etc.). This is a
structural property of LCD technology, is not a sign of
malfunction, and is not covered under your warranty. Such
pixels are not visible when the picture is viewed from a normal
viewing distance.
Note: Interactive video games that involve shooting a "gun"
type of joystick at an on-screen target may not work with this
TV.
Trademarkinformation
• Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are registered trademarks of Dolby
Laboratories.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing LLC.
• Deep Color istrademark of HDMI Licensing LLC. (Only available for
46" and 52" models)
RV530U (E/F) Web 213:276
@ 32 52RV530U EN.book Page 7 Wednesday, January 30 2008 3:54 PM
ImportantSafetyInstructions.......................................... 3
Installation,Care,andService........................................ 3
Chapter1: Introduction............................ g
Features of your new TV ............................ 9
Overview of steps for installing, setting up, and using
your new TV .................................. 9
TV fiont and side panel controls and connections ........ 10
TV back panel connections .......................... 11
Chapter2:ConnectingyourIV ....................... 12
Overview of cable types ............................ 12
About the connection illustrations .................... 12
Connecting a VCR (or a VCR with S-video) and antenna,
Cable TV or Camcorder ......................... 13
Connecting a DVD player with ColorStream °° (component
video), a VCR, and a satellite receiver .............. 14
Connecting a device to the IR OUT infrared terminal
using the IR blaster cable for IR pass-through device
control ...................................... 15
Connecting an HDMI _' or DVI device to the HDMI
input ........................................ 16
REGZA-LINK connection .......................... 17
Connecting a digital audio system .................... 18
Connecting an audio system ......................... 18
Connecting a personal computer (PC) ................. 19
Chapter3: Usingtheremotecontrol................... 20
Preparing the remote control for use ................... 20
Installing the remote control batteries ................. 20
Learning about the remote control .................... 21
Using the remote control to control your other devices .... 22
Remote Control functional key chart .................. 23
Programming the remote control to control your other
devices ...................................... 24
Remote control codes .............................. 25
Chapter4: Menulayoutandnavigation................. 27
Main menu layout ................................. 27
Setup/Installation menu layout ....................... 27
Navigating the menu system ......................... 28
Chapter5:SettingupyourTV........................ 2g
Selecting the menu language ........................ 29
Configuring the antenna input source for the ANT/CABLE
terminal ..................................... 29
Programming channels into the TV's channel memory .... 30
Programming channels automatically .............. 30
Manually adding and deleting channels in the channel
memory .................................. 30
Labeling channels ................................. 31
Setting the HDMI _' audio mode ...................... 32
Viewing the digital signal meter ...................... 33
Setting the time zone ............................... 33
Viewing the system status ........................... 34
Selecting the Power-On Mode ....................... 34
Chapter6: UsingtheTV'sfeatures.................... 35
Selecting the video input source to view ............... 35
Labeling the video input sources ..................... 35
Tuning channels .................................. 36
Tuning channels using the Channel Browser '_' ....... 36
Setting the Channel Tuning Mode ................. 38
Tuning to the next programmed channel ............ 38
Tuning to a specific channel (programmed or
unprogmmmed) ............................ 38
Switching between two channels using Channel
Return ................................... 39
Switching between two channels using SurfLock '_'.... 39
Selecting the picture size ........................... 39
Scrolling the TheaterWide ® picture
(TheaterWide 2 and 3 only) ...................... 41
Using the auto aspect ratio feature .................... 41
Selecting the cinema mode
(480i and 1080i signals) ......................... 42
Using the FREEZE feature .......................... 42
Adjusting the picture ............................... 42
Selecting the picture mode ....................... 42
Adjusting the picture quality ..................... 42
Using the TheaterLock '_' feature ...................... 43
Using the closed caption mode ....................... 43
Base closed captions ........................... 43
Digital CC Settings ............................ 43
CC Selector .................................. 44
Adjusting the audio ................................ 44
Muting the sound .............................. 44
Using the digital audio selector ................... 44
Selecting stereo/SAP broadcasts .................. 45
Adjusting the audio quality ...................... 45
Using the StableSound ® feature ................... 45
Selecting the optical audio output format ........... 46
Using the Dolby ® Digital Dynamic Range Control
feature ................................... 46
Using the Locks menu ............................. 46
Entering the PIN code .......................... 46
If you cannot remember your PIN code ............. 46
Changing your PIN code ........................ 47
Blocking TV programs and movies
by rating iV-Chip) .......................... 47
Downloading an additional rating system for blocking
TV programs and movies .................... 47
Blocking channels ............................. 48
Unlocking programs temporarily .................. 48
Using the input lock feature ...................... 49
Using the GameTimer _ ......................... 49
Using the control panel lock feature ............... 49
Using the PC settings feature ........................ 50
Setting the PC Audio .............................. 50
Setting the sleep timer .............................. 51
Using REGZA-LINK .............................. 51
REGZA-LINK playback device (HD DVD player, etc.)
control ................................... 51
REGZA-LINK input source selection .............. 52
VOLUME and MUTE controls of Audio Receiver .... 52
Other REGZA-LINK functions ................... 52
Using the HDMI settings feature ..................... 53
Displaying TV status information ..................... 54
Understanding the auto power off feature .............. 54
Understanding the last mode memory feature ........... 54
(continuea
7
RV530U (E/F) Web 213:276
@ 32 52RV530U EN.book Page 8 Wednesday, January 30 2008 3:54 PM
Chapter7: UsingtheTV'sadvancedfeatures............. 55
Using the advanced picture settings features ............ 55
Using dynamic contrast ......................... 55
Using the static gamma feature ................... 55
Selecting the color temperature ................... 56
Using CableClem _ digital noise reduction .......... 56
Using MPEG noise reduction ..................... 56
Using the ColorMaster '_' feature .................. 57
Using the Game Mode feature .................... 57
Using the advanced audio settings features ............. 58
Using the surround sound features ................. 58
Chapter8:Troubleshooting......................... 5g
General troubleshooting ............................ 59
LED indications .................................. 61
Chapterg:Appendix.............................. 62
Specifications .................................... 62
Acceptable signal t_rmats
for PC IN and HDMI terminals ................... 63
Limited United States Warranty
for LCD Televisions 26" and Larger ............... 64
Limited Canadian Warranty
for Toshiba Brand Flat Panel Televisions ........... 65
Index........................................ 68
RV530U (E/F) Web 213:276
@ 32 52RV530U EN.book Page 9 Wednesday, January 30 2008 3:54 PM
Featuresof your newTV
The following are just a few of the many exciting features of
your new Toshiba widescreen, integrated HD, LCD TV:
• Integrated digital tuning (SVSB ATSC and QAM)
eliminates the need for a separate digital converter set-top
box (in most cases).
• 1080p output resolution.
• Four HDMI '_'digital, high-definition multimedia
interfaces with 1080p input support (r_¢ page 16).
• HDMI capabilities
Lip-Sync Latency feature activates an auto audio/video
display timing adjustment function that allows HDMI
source devices to accurately perform synchronization
automatically.
Deep Color feature allows the HDMI source to increase the
available colors bits within the boundaries defined by the
RGB or YCbCr color space. (Only supported on 46" and 52"
models)
• REGZA-LINK allows control of external devices from the
TV remote via HDMI connection (_'_¢page 51).
• Two sets of ColorStream ®HD high-resolution component
video inputs (_¢ page 14).
• Digital Audio Out optical audio connection with Dolby ®
Digital optical output format (_ page 46).
• CableClear ®digital picture noise reduction
(_ page 56).
• PC IN (Analog RGB) computer terminal (_¢ page 19).
• Channel Labeling allows you to put the Call Letters (e.g.
ABC, HBO, etc.) on the screen along with the station
numbers, so you always know what you're watching
(r_¢ page 31).
• IR OUT infrared terminal using the IR blaster cable for IR
pass-through device control (_'_¢pages 12 and 15).
• ColorMaster '_'allows you to adjust the TV's standard
colors. The menu for this feature has a unique "black"
design to enhance contrast while you're adjusting the color
(_'_epage 57).
Overviewof steps for installing,
setting up, and usingyour new TV
Follow these steps to set up your TV and begin using its many
exciting features.
1 Observe the following when choosing a location for the
TV:
• Read "Important notes about your LCD TV"
(_'_¢page 6).
• Place the TV in a proper location (_¢ pages 2-5)
2 Do not plug in any power cords until AFTER you have
connected all cables and devices to your TV.
3 BEFORE connecting cables or devices to the TV, learn
the functions of the TV's connections and controls
(g'_ pages 10-11).
4 Connect your other electronic device(s) to the TV
(g'_ pages 12-19).
5 See "Chapter,3: Using the remote control" (g'_ page 20)
for an overview of the buttons on the remote control,
install the batteries and prepare to operate your other
device(s).
6
AFTER connecting all cables and devices, plug in the
power cords for your TV and other devices.
7
See "Menu layout and navigation" for a quick overview of
navigating the TV's menu system (g'_ page 27).
8
Program channels into the TV's channel memory
(g'¢¢page 30).
9
For details on using the TV's features, see Chapters 6
and 7.
10
For help, refer to the Troubleshooting Guide, see
Chapter 8.
11
For technical specifications and warranty information, see
Chapter 9.
RV530U (E/F) Web 213:276
@ 32 52RV530U EN.book Page 10 Wednesday, Janu_y 30, 2008 3:54 PM
TVfront and side panel controlsand connections
Model 42RV530U is used in this manual for illustration purposes.
TVfront
[ZZ_
1 2
Remote sensor-- Point the remote control toward this
remote sensor.
Effective range:
16.4 ft (5m)
2
Green and Yellow LEDs
Green = Power indicator
Yellow = Power-On Mode indicator (_¢ "Selecting the
Power-On Mode" on page 34)
See "LED indications" on page 61 for additional
information.
3
VIDEO 2 IN -- The side panel A/V connections are
referred to as "VIDEO 2" and include standard A/V
connections.
4
POWER -- Press to turn the TV on and off.
If the TV stops responding to the controls on the remote
control or TV control panel and you cannot turn off the
TV, press and hold the POWER button on the TV control
panel for 5 or more seconds to reset the TV.
Rightsidepane[
--8
10
12
5
ARROWS AV< • -- When a menu is on-screen, these
buttons function as up/down/left/right menu navigation
buttons.
6
MENU (ENTER) -- Press to access the menu system
(_ page 27). When a menu is on-screen, the MENU
button on the TV's control panel functions as the ENTER
button.
7
EXIT -- Press to instantly close an on-screen menu.
8
CHANNEL Al!' -- When no menu is on-screen, these
buttons change the channel (programmed channels only;
page 30).
9
VOLUME < • -- These buttons adjust the volume level.
10
INPUT -- Repeatedly press to change the source you are
viewing (ANT/CABLE, VIDEO 1, VIDEO 2,
ColorStream HD1, ColorStream HD2, HDMI 1,
HDMI 2, HDMI 3, HDMI 4, PC).
11
HDMI T"IN -- High-Definition Multimedia Interface
(HDMI 4) input receives digital audio and uncompressed
digital video from an HDMI device or uncompressed
digital video from a DVI device. HDMI connection is
necessary to receive 1080p signals.
12
Service port -- For service use only. Used for updating
the television's firmware.
10
RV530U (ELF) Web 213:276
@ 32 52RV530U EN.book Page 11 Wednesday, Janu_y 30, 2008 3:54 PM
TV back panel connections
For an explanation of cable types and connections, see pages 12-19.
HDMJ iN
TVback
=
j1 2 3
3=
-- HDM 1 -- 4
l Au0,oI
IN IN _ IN
£BN _RF./N VIDEO1
p_ :: RXED
LAII_:
H_IRrl| I
PC IN iN
©l 0,J
OUT
5 6 7 8
1 DIGITAL AUDIO OUT-- Optical audio output in Dolby
Digital or PCM (pulse-code modulation) format for
connecting an external Dolby Digital decoder, amplifier,
A/V receiver, or home theater system with optical audio
input.
2 HDMr IN-- High-Definition Multimedia Interface
input receives digital audio and uncompressed digital
video from an HDMI device or uncompressed digital
video from a DVI device. Also see item 4. HDMI
connection is necessary to receive 1080p signals.
3
PC IN -- For use when connecting a personal computer.
4
PC/HDMI 1 (AUDIO) IN -- PC audio input terminal is
shared with HDMI I analog audio input terminal, and its
use can be configured in the Audio Setup menu
(r_¢ page 50).
5
ColorStream ® HD1 and ColorStream ® HD2 -- Two
sets of ColorStream _ high-definition component video
inputs (with standard stereo audio inputs) for connecting
devices with component video output, such as a Toshiba
DVD player with ColorStream ®.
Note: Component video cables carry only video
inMrmation; separate audio cables are required Mr a
complete connection.
Power cord
--Cable Strap
-AN2
9
6
VIDEO 1 IN -- Standard (composite) video and standard
audio inputs plus optional S-video inputs for connecting
devices with composite video or S-video output.
Note: Standard (composite) video and S-video cables
carry only video information; separate audio cables are
required for a complete connection.
7
Fixed Audio OUT -- Analog audio outputs for
connecting an audio amplifier.
8
IR OUT -- For controlling infrared remote-controlled
devices through the TV. You can connect up to two
devices with an optical IR blaster cable (_¢ page 12), and
then control the devices using the TV's IR pass-through
features.
ANT/CABLE -- Antenna input that supports analog
(NTSC) and digital (ATSC) off-air antenna signals and
analog and digital Cable TV (QAM) signals.
HDMI, the HDMI logo and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing LLC.
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are registered trademarks of Dolby
Laboratories.
11
RV530U (E/F) Web 213:276
@ 32 52RV530U EN.book Page 12 Wednesday, Janu_y 30, 2008 3:54PM
Overviewof cable types
Cables can be purchased from most stores that sell audio/video
devices. Before purchasing any cables, be sure of connector
types required by your devices and the length of each cable.
Coaxial(F-type) cable
Coaxial (F-type) cable is used for connecting your antenna,
cable TV service, and/or cable converter box to the ANT/
CABLE input on your TV.
StandardA/V cables (red/white/yellow)
Standard A/V cables (composite video) usually come in sets of
three, and are for use with video devices with analog audio and
composite video output. These cables (and the related inputs
on your TV) are typically color-coded according to use: yellow
for video, red for stereo right audio, and white for stereo left
(or mono) audio.
HDMr_cable (with HDMI Logo"H_rri|")
HDMI (High-Definition Multimedia Interface) cable is for use
with devices with an HDMI output. An HDMI cable delivers
digital audio and video in its native format. This cable carries
both video and audio information; therefore, separate audio
cables are not required for a complete HDMI device
connection (r_¢ page 16, 17 and 19).
Note: HDMI cable provides better picture performance than a
standard (composite) video or S-video cable.
Dual-wandIR blaster cable
Dual-wand IR blaster cable is for use with video devices with
IR (infrared) remote control. This cable can be used with the
TV's IR pass-through feature (r_¢ page 15).
To obtain IR blaster cable:
Visit http://ceaccessories.toshiba.com/
Optical audio cable
S-videocable
S-video cable is for use with video devices with S-video
output. Separate audio cables are required for a complete
connection.
Note: An S-video cable provides better picture performance
than a composite video cable. Ifyou connect an S-video cable,
be sure to disconnect tf_estandard (composite) video cable or
the picture performance will be unacceptable.
Componentvideo cables (red/green/blue)
Component video cables come in sets of three and are for use
with video devices with component video output.
(ColorStream a_is Toshiba's brand of component video.) These
cables are typically color-coded red, green, and blue. Separate
audio cables are required for a complete connection.
Note: Component video cables provide better picture
performance than a standard (composite) video or S-video
cable.
M
Optical audio cable is for connecting receivers with Dolby
Digital or PCM (pulse-code modulation) optical audio input to
the TV's DIGITAL AUDIO OUT terminal (r_¢ page 18).
Analog RGB(15-pin) computer cable
Analog RGB (15-pin) computer cable is for connecting a PC to
the TV's PC IN terminal (r_¢ page 19).
Note: Separate audio cables are required for a complete
connection.
Aboutthe connectionillustrations
You can connect different types and brands of devices to your
TV in several different configurations. The connection
illustrations in this manual are representative of typical device
connections only. The input/output terminals on your devices
may differ from those illustrated herein. For details on
connecting and using your specific devices, refer to each
device's owner's manual.
12
RV530U (E/F) Web 213:276
@ 32 52RV530U EN.book Page 13 Wednesday, Janu_y 30, 2008 3:54PM
Connectinga VCR(or a VCRwith S-video)and antenna, Cable TV or
Camcorder
TVupperhackpanel
_ VIDEO2 inputs
onTVrightsidepanel
I __,oEo
TVlower hackpanel
L ANT/CABLE J_
You will need:
• coaxial cables
• standard A/V cables
- For better picture performance, if your VCR has S-video,
use an S-video cable (plus the audio cables) instead of
the standard video cable.
- For better picture performance, if your camcorder has
S-video, connect an S-video cable (plus the audio cables)
to VIDEO 1 on the TV back instead of the VIDEO 2 on the
TV right side pane/.
- Ifyou have a mono VCR, connect L/MONO on the TV to
your VCR's audio out terminal using the white audio cable
only.
• S-video cable (if your VCR or camcorder has S-video)
- Do not connect both types of video cable to VIDEO 1 at
the same time or the picture performance will be
unacceptable.
• standard audio cables (if your VCR or camcorder has
S-video)
Note: When you use a Cable box, you may not be able to use
the remote control to program or access certain features on the
TV.
S-video cable
or
Standard
A/V cable
From Cable TV
or antenna
StereoVCR
WOEO LAUDI_
..... CH4 u
From Cable TV
Cable box J
CH 4 OUT
To view the antenna or Cable signal:
Select the ANT/CABLE video input source on the TV.*
To view basic and premium Cable channels:
Turn OFF the VCR. Select the ANT/CABLE video input
source on the TV.* Tune the TV to channel 3 or 4 (whichever
channel the Cable box output is set to). Use the Cable box
controls to change channels.
To view the VCR:
Turn ON the VCR. Select the VIDEO 1 video input source on
the TV.*
To view the camcorder video:
Select the VIDEO 2 video input source on the TV.*
* To select the video input source, press INPUT on the remote control
(t_ page 21). To program the TV remote control to operate other
devices, see Chapter 3.
The unauthorized recording, use, distribution, or revision of
television programs, videotapes, DVDs, and other materials is
prohibited under the Copyright Laws of the United States and
other countries, and may subject you to civil and criminal
liability.
13
RV530U (E/F) Web 213:276
@ 32 52RV530U EN.book Page 14 Wednesday, Janu_y 30, 2008 3:54 PM
Connectinga DVDplayer with ColorStream® (componentvideo), a VCR,
anda satellite receiver
Your TV has two sets of ColorStream ® (component video) inputs.
COMPONENTVIDEO S-VIDEO VIDEO
DVDplayerwith componentvideo
From satellite dish
Satellite receiverwith componentvideo
OUT OUT
@
'%....
You will need:
coaxial cables
standard A/V cables
- For better picture performance, if your VCR has S-video,
use an S-video cable (plus the audio cables) instead of
the standard video cable. Do not connect both types of
video cable to VIDEO 1 at the same time or the picture
performance will be unacceptable.
- Ifyou have a mono VCR, connect L/MONO on the TV to
your VCR's audio out terminal using the white audio cable
only.
standard audio cables
component video cables
- You can connect the component video cables (plus audio
cables) from the DVD player or satellite receiver to either
set of CoIorStream terminals on the TV (HD 1or HD2). The
ColorStream HD1 and HD2 terminals can be used to
display Progressive (480p, 720p) and Interlaced (48d,
1080i). Please check the Owner's Manual of the DVD
player or satellite in order to determine the best output
signal available (1080[) is not supported).
- Ifyour DVD player or satellite receiver does not have
component video, connect a standard A/V cable to
VIDEO 2 on the side panel. If your DVD player has HDMI
video, see page 16.
TV upperhackpanel
TV lowerhackpanel
To view satellite programs using the component video
connections:
Turn on the satellite receiver. Select the ColorStream HD2
video input source on the TV.*
To view the VCR or view and record antenna
channels:
Turn ON the VCR. Tune the VCR to the channel you want to
watch. Select the VIDEO 1 video input source on the TV.*
To record a TV program while watching a DVD:
Turn ON the VCR. Tune the VCR to the channel to record.
Select the ColorStream HD1 video input source on the TV*
to view the DVD.
* To select the video input source, press INPUT on the remote control
(r_ page 21). To program the TV remote control to operate other
devices, see Chapter 3.
The unauthorized recording, use, distribution, or revision of
television programs, videotapes, DVDs, and other materials is
prohibited under the Copyright Laws of the United States and
other countries, and may subject you to civil and criminal
liability.
Fromantenna
StereoVCR
To view antenna or Cable channels:
Select the ANT/CABLE video input source on the TV.*
To view the DVD player:
Turn ON the DVD player. Select the ColorStream HD1
video input source on the TV.*
14
RV530U (E/F) Web 213:276
@ 32 52RV530U EN.book Page 15 Wednesday, Janu_y 30, 2008 3:54PM
Connectinga device to the IR OUT
infrared terminal usingthe IR
blaster cable for IR pass-through
device control
You can use the TV's IN OUT terminal (infrared pass-
through) to remotely operate (through the TV) many infrared
remote-controlled devices (such as Toshiba infrared remote-
controlled VCRs or DVD players) enclosed within an
entertainment center or similar cabinet. Without the IN OUT
connection, the device typically would need to be visible to
operate it remotely.
You will need:
• dual-wand IR blaster cable (_¢ page 12)
• other audio/video cables as required to connect the device(s)
to the TV (_¢ pages 13-16)
FrontofIR-controlledDVDplayer(forexample)
To connect the IR blaster cable:
1
Locate the infrared sensor on the front of your device.
This sensor is marked on some devices.*
2
Align one of the IR blaster cable's wands about 1 inch
away from the infrared sensor on the front of the device
and attach it using double-sided mounting tape. If you
have a second device, attach the second wand in a similar
manner. (See illustration.)
Note: If you do not have a second device, coil the second
wand with a rubber band and leave it behind the TV.
3 Plug the IR blaster cable's plug into the TV's IR OUT
terminal.
To control the device(s):
Point either the device's remote control or the TV remote
control (that you previously programmed to operate the
device; _ Chapter 3) toward the front of the TV and press the
button for the desired function. The signal passes from the
remote control through the TV to the device via the IR blaster
cable.
Frontof Ill-controlledandiodevice(forexample)
I
Infrared.
sensor
IR blastercable wand
(approx.1 inchfrom device)
TVupperhackpanel
=N iN_ IN
4m
PB'@ f@ VI@_ OUT"3
PR :I: FXED
J,©:© ®l,so,o/
I 1@[©1
OUT
Note:
• if you use the device's remote control to operate the device,
you also will need to use the TV's remote control to operate
the TE
• The IR pass-through feature does not support all
IR-controlled devices; satisfactory performance may not be
attainable with certain devices.
*If you cannot locate the device's infrared sensor:
1 Turn OFF the device.
2 Starting at the lower left corner of the device, place the
end of the device's remote control (with the infrared
emitter) so it touches the front of the device and press
POWER. (Do not use the TV's remote control for this
step.)
3 If the device turns on, the point at which the remote
control touched the device is the location of the sensor.
4 If the device does not turn on, move the remote control
slightly to the right and press POWER again.
8 Repeat step 4 until you locate the device's infrared
sensor.
15
RV530U (E/F) Web 213:276
@ 32 52RV530U EN.book Page 16 Wednesday, Janu_y 30, 2008 3:54 PM
Connectingan HDMITMorDVIdevice
to the HDMIinput
The HDMI input on your TV receives digital audio and
uncompressed digital video from an HDMI source device, or
uncompressed digital video from a DVI (Digital Visual
Interface) source device.
This input is designed to accept HDCP (High-Bandwidth
Digital-Content Protection) program material in digital form
from EIA/CEA-861 -D-compliant[_ I consumer electronic
devices (such as a set-top box or DVD player with HDMI or
DVI output).
The HDMI input can accept and display VGA, SVGA, XGA,
WXGA, SXGA, 480i (60Hz), 480p (60Hz), 720p (60Hz),
1080i (60Hz), and 1080p (24Hz/60Hz) signal formats. For
detailed signal specifications, see page 63.
Supported Audio format: Linear PCM, sampling rate 32/44.1/
48 kHz
Note: To connect a PC to the HDMI input, see page 19.
To connect an HDMI device, you will need:
• one HDMI cable (type A connector) per HDMI device
- For proper operation, it is recommended that you use an
HDMI cable with the HDMI Logo (H_:lrll| ).
- To display an 1080p/6OHz signal format, you will need a
Category 2 cable. Conventional HDMI/DVI cable may not
work properly.
- HDMI cable transfers both video and audio. Separate
analog audio cables are not required (see illustration).
- See "Setting the HDMI TMaudio mode" (_ page 32).
TVupperbackpanel TV rightside panel
To connect a DVI device, you will need:
• one HDMI-to-DVI adapter cable (HDMI type A connector)
per DVI device
- For proper operation, the length of an HDM/-to-DV/
adapter cable should not exceed 9.8 ft (3m). The
recommended length is 6. 6 ft (2m).
• one pair of standard analog audio cables per DVI device
- An HDMI-to-DVI adapter cable transfers video only.
Separate analog audio cables are required (see
illustration).
- See "Setting the HDMf _ audio mode" (_ page 32).
TVupperhackpanel
PC/
HDMI 1
l iiis
,OUT
I
Note: To ensure that the HDMI or DVI device is reset properly,
it is recommended that you follow these procedures:
• When turning on your electronic components, turn on the
TV first, and then the HDMI or DVI device.
• When turning offyour electronic components, turn off the
HDMI or DVI device first, and then the TV.
To view the HDMI device video:
Select the HDMI 1,HDMI 2, HDMI 3, or HDMI 4 video input
source on the TV.*
* To select the video input source, press INPUT on the remote control
(r_ page 21). To program the TV remote control to operate other
devices, see Chapter 3.
16
[1] EIA/CEA-861-D compliance covers the transmission of
uncompressed digital video with high-bandwidth digital content
protection, which is being standardized for reception of high-
definition video signals. Because this is an evolving technology, it
is possible that some devices may not operate properly with the TV.
HDMI, the HDMI logo and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing LLC.
RV530U (E/F) Web 213:276
@ 32 52RV530U EN.book Page 17 Wednesday, Janu_y 30, 2008 3:54 PM
REGZA-LINKconnection
You can control the basic functions of connected audio/video devices using the TV's remote control if you connect a
REGZA-LINK compatible audio receiver or playback device. For an explanation of setup and operations, see pages 51 and 52.
TV upperhackpanel
I 1.....
Audioreceiver
Playbackdevice
(REGZA-LNKHDDVDplayer,etc.)
To connect an Audio Receiver and Playback Devices,
you will need:
• HDMI cables (r_¢ page 16)
Note:
• if several devices are connected, REGZA-L/NK feature may
not operate properly.
• For proper operation, it is recommended that you use HDMI
cables with the HDMI Logo (I-1£:311111).
.DM__N-- TV rightsidepanel
N N
Playbackdevice
(REGZA-LNKHDDVDplayer,etc.)
Before controlling the device(s):
• After completing the above connections, set the REGZA-
LINK Setup menu as you desire (r_¢ page 52).
• The connected devices must also be set. For details, see the
operation manual for each device.
• The REGZA-LINK feature uses the CEC technology as
regulated by the HDMI standard.
• This feature is limited to models incorporating Toshiba's
REGZA-LINK. However, Toshiba is not liable for those
operations. Refer to the individual instruction manuals for
compatibility information.
17
RV530U (E/F) Web 213:276
@ 32 52RV530U EN.book Page 18 Wednesday, Janu_y 30, 2008 3:54PM
Connectinga digital audiosystem
The TV's DIGITAL AUDIO OUT terminal outputs aDolby ®*
Digital p,D_ or 2-channel down-mixed PCM (pulse-code
modulation) signal for use with an external Dolby <'_Digital
decoder or other external audio system with optical audio
input.
You will need:
• optical audio cable (Use an optical audio cable that has the
larger "TosLink" connector and not the smaller "mini-
optical" connector.)
°°'°2:°°'
Note:
• Some audio systems may not be compatible with Do/by
Digital bitstream signals. Older audio systems that are not
compatible with standard optical out signals may not work
properly, creating a high noise level that may damage
speakers or headphones. THIS DAMAGE ISNOT COVERED
BY YOUR WARRANTX
• The DIGITAL AUDIO OUT terminal may not output some
digital audio sources because of copy restrictions.
* Manufactured under license from Dolby Laboratories.
Dolby, and the double-D symbol are registered trademarks of Dolby
Laboratories.
Connectingan audio system
This connection allows you to use external speakers with an
external analog audio amplifier to adjust the sound level.
k
To control the audio:
1 Turn on the TV and the digital audio device.
2 Press M_uon the TV's remote control and open the Audio
menu.
3 Highlight Audio Setup and press @.
Digital Audio Selector
Audio Se!!ings ...............................................................
Advanced Audio Settings
4
In the Optical Output Format field, select either
Oolby Digital or PCM, depending on your device
(gW "Selecting the optical audio output format" on
page 46).
You will need:
• standard audio cables
TVupperbackpanel _
F©i©j _v'_°l/
To control the audio:
1 Turn on the TV and the stereo amplifier.
2 Minimize the sound volume from the TV's built-in
speakers and control the volume level using the
amplifier's remote control.
18
RV530U (E/F) Web 213:276
32 52RV530U EN.book Page 19 Wednesday, Janu_y 30, 2008 3:54 PM
Connectinga personalcomputer
(PC)
With either the PC IN or HDMI connection, you can watch
your computer's display on the TV and hear the sound from the
TV' s speakers.
To connect a PC to the PC IN terminal on the TV:
When connecting a PC to the PC IN terminal on the TV, use an
analog RGB (15-pin) computer cable and a PC audio cable.
TV upperhack panel
Signal names for mini D-sub 15-pin connector
1 R
2 G
3 B
4 NC *
5 NC
•NC=Not connected
6 Ground 11 NC
7 Ground 12 NC
8 Ground 13 H-sync
9 NC 14 V-sync
10 Ground 15 NC
To connect a PC to the HDMI terminal on the TV:
When connecting a PC to the HDMI terminal on the TV, use
an adapter cable and analog audio cables.
If connecting a PC with an HDMI terminal, use an HDMI cable
(type A connector). Separate analog cables are not necessary
(r'_¢page 16).
Conversion adapter
(if necessary)
• To use a PC, set the monitor output resolution on the PC
before connecting it to the TV. The PC IN terminal can
accept and display VGA, SVGA, XGA, WXGA, and SXGA
signal formats. For detailed signal specifications, see page
63.
• To display the optimum picture, use the PC setting feature
(g'_ "Using the PC settings feature" on page 50).
Note:
• The PC audio input terminals on the TVare shared with the
HDMI 1analog audio input terminals (_ page 50).
• Some PC models cannot be connected to this TV.
• An adapter is not needed for computers with a compatible
mini D-sub 15-pin terminal.
• Depending on the DVD's title and the specifications of the
PC on which you are playing the DVD-Video, some scenes
may be skipped or you may not be able to pause during
multi-angle scenes.
TVupper backpanel
PC/
HDMI 1
E IN IN _ IN
LTLL ....
VIDE¢
iY •
iii_fi
PC audio
cable
Computer
The HDMI input can accept and display VGA, SVGA, XGA.
WXGA, SXGA, 480i (60Hz), 480p (60Hz), 720p (60Hz),
1080i (60Hz), and 1080p (24Hz/60Hz) signal formats. For
detailed signal specifications, see page 63.
Note:
• The edges of the images may be hidden.
• If receiving a 480i (HDMI), 480[) (HDMI), 720p, 1080L or
1080[) signal program, Native mode scales the video to
display the entire picture within the borders of the screen
(i.e. no overscanning).
19
RV530U (E/F) Web 213:276
32 52RV530U EN.book Page 20 Wednesday, Janu_y 30, 2008 3:54 PM
Preparingthe remote control
for use
Your TV remote control can operate your TV and many other
devices such as cable converter boxes, satellite receivers,
VCRs, DVD players, and HTIBs (home theater in a box), even
if they are different brands.
If you have a Toshiba device:
Your TV remote control is preprogrammed to operate most
Toshiba devices (r_¢ page 24).
If you have a non-Toshiba device or a Toshiba device
that the remote control is not preprogrammed to
operate:
You can program the TV remote control so it will operate the
other device (r_¢ pages 22-26).
Installing the remote control
batteries
1 Remove the battery cover from the back of the remote
control.
Squeeze tab
and lift cover.
2
Install two "AAA" size batteries, making sure to match
the + and - signs on the batteries to the signs on the battery
compartment.
3
Reinsert the battery cover in the remote control until the
tab snaps.
Caution: Batteries must not be exposed to excessive heat
such as sunshine, fire or the like.
Note:
• Be sure to use AAA size batteries.
• Dispose of batteries in a designated disposal area.
• Batteries should always be disposed of with the
environment in mind. Always dispose of batteries in
accordance with appficable laws and regulations.
• If the remote control does not operate correctly, or if the
operating range becomes reduced, replace batteries with
new ones.
• When necessary to replace batteries in the remote control,
always replace both batteries with new ones. Never mix
battery types or use new and used batteries in combination.
• Always remove batteries from the remote control if they are
dead or if the remote control is not to be used for an
extended period of time. This will prevent battery acid from
leaking into the battery compartment.
2O
RV530U (E/F) Web 213:276
@ 32 52RV530U EN.book Page 21 Wednesday, Janu_y 30, 2008 3:54 PM
Learningabout the remote control
The buttons used for operating the TV only are described here.
For a complete list of the remote control's functions, see the
remote control functional key chart (_'q¢page 23).
2
8
13
15
16
17
PLAY
TV/VCR REC RESUMEPLAY SLOW
SEARCH
MODE SELECT
1
6
7
10
11
18
19
1 POWER turns the TV on and off. When the TV is on, the
green LED indicator on the TV front will be illuminated.
2 FREEZE freezes the picture.
Press again to restore the moving picture (_,v page 42).
3 SLEEP accesses the sleep timer (_,v page 51).
4 PIC SIZE cycles through thepicture sizes: Natural,
TheaterWide 1/2/3, Full, 4:3 HD, Native, and Dot by
Dot (_ page 39).
5 Channel Numbers (0-9, -/100) directly tune
channels. The (_) button is used to tune digital channels
(_,v page 38) or to edit the Favorites List (_,v page 36).
6 INPUT selects the video input source (_,v page 35).
7 CH Al!' cycles through programmed channels when no
menu is on-screen (_ page 30).
8 VOL + - adjusts the volume level.
9 FAV BROWSER accesses the Favorites List in the
Channel Brower'" (_ page 36).
10 RECALL displays TV status information (_'q¢page 54).
11 CH RTN returns to the last viewed channel or source
(_ page 39).
12 MUTE reduces or turns off the sound (_ page 44).
13 INFO displays TV status information as well as program
details, when available (_ page 54).
14 '_ • / _i • While watching TV, these buttons open the
Channel Browser '_'and tune to the previous/next channel
in the channel history (_ page 37). (Also see "Arrow
buttons.")
15 Arrow buttons (AT• •) When a menu is on-screen,
these buttons select or adjust programming menus. (Also
see
16 ENTER activates highlighted items in the main menu
system.
17 MENU accesses the main TV menu system (_,v page 27).
18 EXIT closes on-screen menus.
19 MODE SELECT switch switches between TV,
CABLE/SAT, AUX 1, and AUX 2 modes (_,v page 22).
Set to "TV" to control the TV.
TOSHIBA
CT-90302
Note: The error message "Not A vai/ab/e" may appear if you
press a key for a function that is not available.
21
RV530U (E/F) Web 213:276
Loading...