Toshiba 52HMX85, 46HMX85, 62HMX85 User Manual

IntroductionConnecting

your TV

WNER'S

ANUAL

DLPTM Projection Television

46HMX85

52HMX85 62HMX85

Using the

remote control

your TV

Setting up

46HMX85 52HMX85 62HMX85

Owner's Record

The model number and serial number are on the back of your TV. Record these numbers in the spaces below. Refer to these numbers whenever you communicate with your Toshiba dealer about this TV.

Model:

Serial No.:

YC/N

23566642

Features

Using the TV’s

AppendixIndex

#01E01_46/52/62HMX85 5/10/05, 12:39 PM1

Black

(E) 46/52/62HMX85

Dear Customer,

Thank you for purchasing this Toshiba TV. This manual will help you use the many exciting features of your new TV. Before operating the TV, please read this manual completely, and keep it nearby for future reference.

Safety Precautions

WARNING: TO REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning symbol in the triangle tells you that the voltage inside this product may be strong enough to cause an electric shock. DO NOT TRY TO SERVICE THIS PRODUCT YOURSELF.

The exclamation mark in the triangle tells you that important operating and maintenance instructions follow this symbol.

Lamp Unit Replacement

CAUTION: HOT SURFACE! The temperature of the lamp immediately after use exceeds 392°F (200°C).

cooled will result in severe burns. ALLOW THE LAMP TO COOL FOR AT LEAST ONE (1) HOUR BEFORE REPLACING IT.

The lamp in this product has a limited service life. The length of service life varies depending on product use and user settings. If you use the lamp beyond its service life:

• you may notice a reduction in the colors and/or brightness of the picture, at which time you should replace the lamp unit; and

• the strength of the quartz glass in the lamp will be reduced and the lamp may rupture. If the lamp ruptures, the TV will not operate until the lamp unit is replaced.

See “Appendix” on pages 60–64.

• Dispose of the used lamp unit by the approved method for your area.

disposal or recycling information, contact your local authorities.

Touching the lamp before it has

Note:

The lamp unit contains mercury. Disposal of mercury

may be regulated due to environmental considerations. For

NOTE: NEVER CONNECT THIS TV TO A PERSONAL COMPUTER (PC).

THIS TV IS NOT INTENDED FOR USE WITH A PC.

NOTICE OF POSSIBLE TV STAND INSTABILITY

CAUTION: This television is for use only with Toshiba television stands specifically designed for this television model.

Please contact your authorized Toshiba dealer or visit the Toshiba Canada web site at www.toshiba.ca to determine the appropriate stand for your television.

Child Safety

It Makes A Difference Where Your TV Stands

Congratulations on your purchase! As you enjoy your new TV, keep these safety tips in mind:

The Issue

 If you are like most consumers, you have a TV in your home.

Many homes, in fact, have more than one TV.

 The home theater entertainment experience is a growing

trend, and larger TVs are popular purchases; however, they are not always supported on the proper TV stands.

 Sometimes TVs are improperly secured or inappropriately

situated on dressers, bookcases, shelves, desks, audio

speakers, chests, or carts. As a result, TVs may fall over,

causing unnecessary injury.

Toshiba Cares!

 The consumer electronics industry

is committed to making home entertainment enjoyable and safe.

 The Consumer Electronics Association

formed the Home Entertainment Support Safety

Committee, comprised of TV and consumer

electronics furniture manufacturers, to advocate

children’s safety and educate consumers and their

families about television safety.

Tune Into Safety

 One size does NOT fit all! Use appropriate furniture large

enough to support the weight of your TV (and other electronic components).

 Use appropriate angle braces, straps, and anchors to secure

your furniture to the wall (but never screw anything directly into the TV).

 Carefully read and understand the other enclosed

instructions for proper use of this product.

 Do not allow children to climb on or play with furniture

and TVs.

 Avoid placing any item on top of your TV (such as a VCR,

remote control, or toy) that a curious child may reach for.

 Remember that children can become excited while watching

a program and can potentially push or pull a TV over.

 Share our safety message about this hidden hazard of the

home with your family and friends. Thank you!

2500 Wilson Blvd. Arlington, VA 22201 U.S.A. Tel. 703-907-7600 Fax 703-907-7690 www.CE.org

CEA is the Sponsor, Producer and Manager of the International CES

#01E02-05_46/52/62HMX85 5/10/05, 12:39 PM2

Black

(E) 46/52/62HMX85

Important Safety Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being

walked on or pinched, particularly at plugs, convenience receptacles, and the point where it exits the apparatus.

11) Only use attachments/accessories specified by the

manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use

caution when moving the cart/apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or

when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. (This does not apply to the “Lamp Unit Replacement” described on pages 60-64 of this manual.)

CAUTION: If the TV is dropped and the cabinet or enclosure surface has been damaged or the TV does not operate normally, take the following precautions:

•ALWAYS turn off the TV and unplug the power cord to

avoid possible electric shock or fire.

• Never handle the damaged television, it may cause an injury.

•ALWAYS contact a service technician to inspect the TV

any time it has been damaged or dropped.

15) CAUTION: To reduce the risk of electric shock, do not use the polarized plug with an extension cord, receptacle, or other outlet unless the blades can be inserted completely to prevent blade exposure.

16) WARNING: This product contains a lamp to project

the picture, and requires special safety precautions:

• See pages 60–64 for instructions on lamp unit replacement.

• DO NOT attempt to service this product except as

specified on pages 60–64. The only user-serviceable item in this product is the lamp unit.

Wide plug

Installation, Care, and Service

Installation

Follow these recommendations and precautions and heed all warnings when installing your TV:

17) Never modify this equipment. Changes or modifications may void: a) the warranty, and b) the user’s authority to operate this equipment under the rules of the Federal Communications Commission.

18) DANGER: RISK OF SERIOUS PERSONAL

INJURY, DEATH, OR EQUIPMENT DAMAGE! Never place the TV on

an unstable cart, stand, or table. The TV may fall, causing serious personal injury, death, or serious damage to the TV.

19) Never place or store the TV in direct sunlight; hot, humid areas; areas subject to excessive dust or vibration; or locations with temperatures at or below 41°F (5°C).

20) Always place the TV on the floor or a sturdy, level, stable surface that can support the weight of the unit.

21) Never expose the apparatus to dripping or splashing or place items such as vases, aquariums, any other item filled with liquid, or candles on top of the TV.

22) Always place the back of the television at least one (1) inch away from any vertical surface (such as a wall) to allow proper ventilation.

23) Never block or cover the slots or openings in the TV cabinet back, bottom, and sides. Never place the TV:

• on a bed, sofa, rug, or similar surface;

• too close to drapes, curtains, or walls; or

• in a confined space such as a bookcase, built-in cabinet,

or any other place with poor ventilation.

The slots and openings are provided to protect the TV from overheating and to help maintain reliable operation of the TV.

24) Never allow anything to rest on or roll over the power cord, and never place the TV where the power cord is subject to wear or abuse.

25) Never overload wall outlets and extension cords.

26) Always operate this equipment from a 120 VAC, 60 Hz power source only.

(continued on next page)

#01E02-05_46/52/62HMX85 5/10/05, 12:39 PM3

Black

(E) 46/52/62HMX85

Ground clamp

Antenna discharge unit (NEC Section 810-20)

Grounding conductors (NEC Section 810-21)

Power service grounding electrode system (NEC Art 250 Part H)

Ground clamps

Antenna lead-in wire

Electric service equipment

Installation

(cont. from previous page)

Care

(cont. from previous column)

27) Always make sure the antenna system is properly grounded to provide adequate protection against voltage surges and built-up static charges (see Section 810 of the National Electric Code).

28) DANGER: RISK OF SERIOUS PERSONAL

INJURY OR DEATH!

• Use extreme care to make sure you are never in

a position where your body (or any item you are in contact with, such as a ladder or screwdriver) can accidentally touch overhead power lines. Never locate the antenna near overhead power lines or other electrical circuits.

• Never attempt to install any of the following during lightning activity: a) an antenna system; or b) cables, wires, or any home theater component connected to an antenna or phone system.

33) For added protection of your TV from lightning and power surges, always unplug the power cord and disconnect the antenna from the TV if you leave the TV unattended or unused for long periods of time.

) During normal use, the TV may make occasional snapping

or popping sounds. This is normal, especially when the unit is being turned on or off. If these sounds become frequent or continuous, unplug the power cord and contact a Toshiba Authorized Service Center.

35)

Special care for DLP

•

Lamp—The lamp in this product has a limited service life.

(digital light processing) units:

The length of service life varies depending on product use or user settings. If you use the lamp beyond its service life:

- you may notice a reduction in the colors and/or

brightness of the picture, at which time you should replace the lamp unit; and

- the strength of the quartz glass in the lamp will be

reduced and the lamp may rupture. If the lamp ruptures, the TV will not operate until the lamp unit is replaced.

See “Appendix” on pages 60–64.

• The lamp unit contains mercury. Disposal of

mercury may be regulated due to environmental considerations. For disposal or recycling

information, please contact your local authorities.

• Dispose of the used lamp unit by the approved method for your area.

Care

For better performance and safer operation of your TOSHIBA TV, follow these recommendations and precautions:

29) Always sit approximately 10–25 feet away from the TV and as directly in front of it as possible. The picture can appear dull if you sit too far to the left or right of the TV, or if sunlight or room lights reflect on the screen. Turn the TV off to check for reflections on the screen, and then remove the source of reflections while viewing the TV.

30) Always unplug the TV before cleaning. Never use liquid or aerosol cleaners. Clean only with a soft dry cloth. Do not spray volatile compounds, such as insecticide, on the cabinet. This may discolor or damage the cabinet.

31) WARNING: RISK OF ELECTRIC SHOCK!

Never spill liquids or push objects of any kind into the TV cabinet slots.

32) If the air temperature rises suddenly (for example, when the TV is first delivered), condensation may form on the lenses. This can make the picture appear distorted or the color appear faded. If this happens, turn off the TV for 6 to 7 hours to allow the condensation to evaporate.

Service

) WARNING: RISK OF ELECTRIC SHOCK!

Never attempt to service the TV yourself,

except as specified on pages 60–64. Opening and removing the covers may expose you to dangerous voltage or other hazards. Failure to follow this WARNING may result in death or serious injury. Refer all servicing not specified in this manual to a Toshiba Authorized Service Center.

37) If you have the TV serviced:

• Ask the service technician to use only replacement parts

specified by the manufacturer.

• Upon completion of service, ask the service technician to

perform routine safety checks to determine that the TV is in safe operating condition.

38)When the TV reaches the end of its useful life, ask a qualified service technician to properly dispose of the TV.

Note: The lamp unit contains mercury. Disposal of mercury may be regulated due to environmental considerations. Dispose of the used lamp unit by the approved method for your area. For disposal or recycling information, please contact your local authorities.

#01E02-05_46/52/62HMX85 5/10/05, 12:39 PM4

Black

(E) 46/52/62HMX85

Important notes about your DLP™ projection TV

1) The light source for this TV is a projection lamp unit with a limited service life. When the lamp wears out, the picture may become dark or black, or the lamp may fail, at which time you must replace the lamp unit. See “Lamp unit replacement” on pages 60-64.

2) If you set the lamp mode to LOW POWER, each time you turn on the TV, the lamp will start out in HI BRIGHT mode but will switch to LOW POWER mode in approximately 1 minutes. You will notice a change in screen brightness when this happens. This is not a malfunction. (See page 49 for details.)

3) Each time you turn on the TV, it may take several seconds to go from no picture to full picture brightness.

4) The display on this TV is manufactured using a chip that may contain up to 1.3 million microscopic mirrors. Each of these micromirrors measures less than one-fifth the width of a human hair and represents a single pixel on the television display. These micromirrors are mounted on tiny hinges that enable them to tilt either toward the light source (ON) or away from it (OFF). Occasionally, one of these mirrors may become inoperative, creating a light or dark pixel on the projection surface. This is a structural property of DLP™ projection TV technology, and is not a sign of malfunction. Such pixels are not visible when the picture is viewed from a normal viewing distance (see item 29 on page 4).

5) Depending on the media you are viewing, it is possible, although unlikely, that a limited number of viewers may see a “rainbow effect” on the screen, which can, in rare instances, result in eye fatigue. This is a rare occurrence related to technology of this type, and is not a sign of TV malfunction.

6) Always sit approximately 10–25 feet away from the TV and as directly in front of it as possible. The picture quality may be affected by your viewing position and length of viewing time. If you sit too closely to the TV for too long, you may suffer from eye fatigue. See item 29 on page 4.

7) This TV contains several cooling fans to moderate

the internal temperature. You may be able to hear

the fans for several minutes after the TV is turned off. This is a function of the Quick Restart standby mode and is not a sign of TV malfunction. You can set the Quick Restart feature to stop the fans as soon as the TV is turned off. See “Selecting the Quick Restart” on page 28.

8) The green and red LED lights on the control touchpad (on the lower right corner of the TV screen) indicate your TV’s current status. If either light flashes, see “LED indications” on page 64 for details.

9) Review all safety and operating information in this owner’s manual before you use your TV.

The DLP logo and DLP medallion are trademarks of Texas Instruments. DLP • is a trademark of Texas Instruments.

#01E02-05_46/52/62HMX85 5/10/05, 12:39 PM5

Black

(E) 46/52/62HMX85

Important Safety Information............................. 2-5

Introduction................................................................ 7

Welcome to Toshiba ......................................................... 7

Exploring your new TV ................................................... 7

Connecting your TV .................................................. 8

Connecting an antenna or cable TV................................. 8

Connecting a VCR .......................................................... 9

Connecting a cable converter box .................................... 9

Connecting a cable converter box and VCR................... 10

Connecting a DVD player or satellite receiver and

a VCR............................................................................ 11

Connecting a DVD player with ColorStream

(component video) and a VCR ...................................... 12

Connecting a DTV receiver/set-top box with ColorStream

(component video) and a VCR................ 13

Connecting two VCRs ................................................... 14

Connecting a camcorder ................................................ 14

Connecting an HDMI™ or a DVI device to the

HDMI inputs ................................................................ 15

Connecting an audio system .......................................... 16

Using the remote control ...................................... 17

Preparing the remote control for use .............................. 17

Installing the remote control batteries ............................ 17

Remote Control functional key chart ...................... 18

Programming the remote control for use with

your audio/video devices ................................................ 20

Device code setup ................................................... 20

Searching and sampling the code

of a device [8500] ................................................... 20

Using the volume lock feature [8000] ..................... 21

Operational feature reset [8900] ............................. 21

Device code table ....................................................22

Learning about the remote control .......................... 24

Setting up your TV .................................................. 25

Turning on the TV ........................................................ 25

Learning about the menu system ................................... 25

Changing the on-screen display language ....................... 26

Selecting the antenna input............................................ 26

Adding channels to the TV’s memory ............................ 27

Programming channels automatically ......................27

Adding and erasing channels manually.................... 28

Changing channels ........................................................ 28

Selecting the Quick Restart ............................................ 28

Using the TV’s features.......................................... 29

Adjusting the channel settings........................................ 29

Switching between two channels using Channel

Return .................................................................... 29

Switching between two channels using

SurfLock™ ............................................................. 29

Programming your favorite channels ....................... 29

Labeling channels ................................................... 31

Viewing the wide-screen picture formats

(480i, 480p, and 1080i signals only) ...........................32

Selecting the picture size ......................................... 32

Scrolling the TheaterWide

picture

(TheaterWide 2 and 3 only) ................................... 34

Using the AUTO ASPECT feature ......................... 35

Using the POP double-window feature .......................... 36

Swapping the main and POP pictures ..................... 37

Switching the speaker sound

(main or POP program).......................................... 37

Double-Window aspect ratio .................................. 38

Using the programmed channel search function............. 38

Using the favorite channel search function .............. 39

Automatic favorite channel search feature ............... 39

Using the LOCKS menu ............................................... 40

Entering the PIN code ............................................ 40

If you cannot remember your PIN code .................. 40

Using the V-CHIP menu ............................................... 40

ENABLE BLOCKING .......................................... 41

TV RATING (Independent rating system for

broadcasters) ........................................................... 41

MPAA RATING (Independent rating system for

movies) ................................................................... 42

BLOCKING OPTION.......................................... 42

Unlocking programs temporarily ............................ 43

Locking channels ........................................................... 43

Locking the video inputs................................................ 45

Changing the PIN code ................................................. 45

Adjusting the picture ..................................................... 46

Selecting the picture mode ......................................46

Adjusting the picture quality ................................... 46

Selecting the color temperature ............................... 47

Using the CableClear

DNR feature ....................... 47

Saving your new preferences ................................... 48

Resetting your picture setting adjustments .............. 48

Selecting the lamp mode ......................................... 49

Selecting the cinema mode...................................... 49

Selecting the video input source .....................................50

Labeling the video input sources .................................... 50

Using the closed caption feature..................................... 51

Setting the ON timer ..................................................... 52

Setting the sleep timer.................................................... 52

Setting the clock ............................................................ 53

Adjusting the sound ....................................................... 54

Muting the sound ................................................... 54

Selecting stereo/SAP broadcasts .............................. 54

Using the WOW™ surround sound feature ........... 55

Adjusting the sound quality .................................... 55

Enjoying the Dolby Virtual surround sound

feature..................................................................... 56

Resetting your audio adjustments ........................... 57

Using the StableSound

feature .............................. 57

Turning off the built-in speakers ............................. 58

Selecting the AUDIO OUT sound ......................... 58

Selecting the background of the menu display ............... 59

Displaying TV status information on-screen .................. 59

Understanding the auto power off feature ...................... 59

Understanding the last mode memory feature ................ 59

Appendix................................................................... 60

Lamp unit replacement .................................................. 60

When to replace the lamp unit................................ 60

How to replace the lamp unit ................................. 61

Lamp unit disposal ................................................. 64

LED indications ............................................................ 64

Specifications ................................................................. 65

Tr oubleshooting .............................................................66

Limited Canada Warranty ..............................................68

Index .......................................................................... 69

#01E06_46/52/62HMX85 5/10/05, 12:39 PM6

Black

(E) 46/52/62HMX85

Introduction

Welcome to Toshiba

Thank you for purchasing this Toshiba TV, one of the most innovative DLP manual is to guide you through setting up and operating your Toshiba TV as quickly as possible.

This manual applies to models 46HMX85, 52HMX85, and 62HMX85. The model and serial numbers are on the back of your TV. Write these numbers in the space provided on the front cover of this manual for your records.

Instructions in this manual are based on using the remote control. You can also use the controls on the TV if they have the same name as those on the remote control.

Please read all the safety and operating instructions carefully, and keep the manual for future reference.

Exploring your new TV

projection TVs on the market. The goal of this

See “Important notes about your DLPTM projection TV” on page 5.

IntroductionConnecting

your TV

You can operate your TV using the control touchpad on the TV front or the remote control. The back panel and side panel (behind the door) provide terminals for connecting other equipment to your TV. See “Connecting your TV” on page 8.

Model 52HMX85 is used in this manual for illustration purposes.

Front

MENUVOLUMECHANNELEXITTV/VIDEO POWER

Remote control sensor

(Behind the screen)

Side

Push to open.

Control touchpad on TV front (Gently touch the printed keys.)

EXIT

zyx •

TV/VIDEO

Volume x •

Channel zy

* Green ON = Touchpad key being pressed;

Red ON = Power ON. See page 64 for additional LED indications.

VIDEO 3

/audio inputs

Vid

IN*

ANT OUTAUDIO

ANT-2 IN

ANT-1 IN

POWER

MENUVOLUMECHANNELEXITTV/VIDEO POWER

Green and Red LED indicators*

Remote control

LIGHT SLEEP

CABLE/SAT VCR DVD

123

AUDIO1 AUDIO2

456

MODE

789

PIC SIZE

+10

100/

INPUT

PAUSE/STEP

AM/FM DISC

SPLIT

SWAP

FAV

ENTER

FAV

EXIT

DVD CLEAR

POP DIRECT CH

RECALL

SKIP/SEARCH

PLAYREW FF

STOP

CH SCAN

ACTION

DVD RTN CH RTN

SLOW/DIR

TV/

VCR

POP CH

POWER

ENT

VOL

MUTE

REC

FREEZE

SOURCE

Using the

remote control

your TV

Setting up

Features

Using the TV’s

* Model 46HMX85 is equipped with one HDMI input terminal and one set of AUDIO

IN jacks.

#01E07_46/52/62HMX85 5/10/05, 12:39 PM7

Black

(E) 46/52/62HMX85

Back

120 VAC

60 Hz

VIDEO 1/2

ColorStream

HD-1/HD-2

Video/Audio OUT

AppendixIndex

CT-90164

Variable Audio OUT

HDMI IN*

Connecting your TV

Note: Cables are not supplied with your TV.

IntroductionConnecting

your TV

Using the

Remote Control

●

Connecting an antenna or cable TV

This connection allows you to watch TV programs or basic cable channels.

Coaxial cable is the cable that comes in from your antenna, cable TV service, or cable converter box. Coaxial cable uses “F” connectors.

Standard A/V (audio/video) cables usually come in sets of three, and are typically color-coded according to use: yellow for video, red for stereo right audio, and white for stereo left (or mono) audio. On your TV’s back panel, the standard A/V inputs are color-coded in the same manner as the cables.

S-video cable is for use with video equipment that has S-video output. Component video cables come in sets of three, and are for use with

video equipment that has component video output. (ColorStream® is Toshiba’s brand of component video.)

HDMI cable is for use with video equipment that has an HDMI output (type A connector) (see page 15).

NOTE:

NEVER CONNECT THIS TV TO A PERSONAL COMPUTER

(PC). THIS TV IS NOT INTENDED FOR USE WITH A PC.

Coaxial (antenna) cable

Standard A/V cables (red/white/yellow)

S-video cable

Component video cables

HDMI cable

CAUTION: RISK OF EQUIPMENT DAMAGE!

Never plug in any power cords until you have finished connecting all equipment.

your TV

Setting up

Features

Using the TV’s

AppendixIndex

From Antenna or Cable

Model 46HMX85 is equipped with one HDMI input terminal and one set of AUDIO IN jacks.

#01E08-16_46/52/62HMX85 5/10/05, 12:39 PM8

Black

(E) 46/52/62HMX85

Connecting a VCR

This connection allows you to watch local channels and video programs, play or record on the VCR while watching TV, and record from one channel while watching another channel.

You will need:

• two coaxial cables

• one set of standard A/V cables

From Cable Box or Antenna

Stereo VCR

IN from ANT OUT to TV CH 3

CH 4

VIDEO

OUT

AUDIO

Note:

If you have a mono VCR, connect L/Mono to VCR Audio OUT using only one audio cable.

If you have a VCR with S-video, use an S-video cable (in the S-video jacks) instead of a standard video cable.

Do not connect a standard video cable and an S-video cable to VIDEO 1 (or VIDEO 2) at the same time, or the picture performance will be unacceptable.

The unauthorized recording, use, distribution, or revision of television programs, videotapes, DVDs, and other materials is prohibited under Copyright Law and may subject you to civil and criminal liability.

IntroductionConnecting

your TV

Using the

remote control

Connecting a cable converter box

This connection allows you to watch basic and premium cable channels To watch basic cable and use the TV’s features, select ANT-1. To view

premium channels, select ANT-2, tune the TV to channel 3 or 4 (whichever channel is vacant in your area), and use the converter box to change channels.

You will need:

• three coaxial cables

From Cable

INOUT

Note:

When you use a converter box with your TV, the remote control may not operate some features, such as programming your favorite channels, labeling channels, and locking channels.

your TV

Setting up

Features

Using the TV’s

AppendixIndex

Model 46HMX85 is equipped with one HDMI input terminal and one set of AUDIO IN jacks.

#01E08-16_46/52/62HMX85 5/10/05, 12:39 PM9

Black

(E) 46/52/62HMX85

Cable converter box

Connecting a cable converter box and VCR

This connection allows you to watch and record basic and premium cable channels, watch videotapes, and record one channel while

IntroductionConnecting

your TV

Using the

Remote Control

watching another channel. To watch basic cable and use the TV’s features, select ANT-1.

To view premium channels or record with the VCR, select ANT-2, tune the TV and VCR to channel 3 or 4 (whichever channel is vacant in your area), and use the converter box to change channels.

You will need:

• four coaxial cables

• one set of standard A/V cables

Note:

If you have a mono VCR, connect L/Mono to VCR Audio OUT using only one audio cable.

If you have a VCR with S-video, use an S-video cable (in the S-video jacks) instead of a standard video cable. Do not connect a standard video cable and an S-video cable to VIDEO 1 (or VIDEO 2) at the same time, or the picture performance will be unacceptable.

When you use a converter box with your TV, the remote control may not operate some features, such as programming your favorite channels, labeling channels, and locking channels.

From Cable

your TV

Setting up

Features

Using the TV’s

AppendixIndex

IN from ANT OUT to TV CH 3

CH 4

Stereo VCR

VIDEO

OUT

AUDIO

INOUT

Cable converter box

Model 46HMX85 is equipped with one HDMI input terminal and one set of AUDIO IN jacks.

#01E08-16_46/52/62HMX85 5/10/05, 12:39 PM10

Black

(E) 46/52/62HMX85

Connecting a DVD player or satellite receiver and a VCR

This connection allows you to watch DVD/satellite, VCR, and TV programs, and record one TV channel while watching another channel.

You will need:

• two (or three, if satellite receiver is used) coaxial cables

• one set of standard A/V cables

• one S-video cable

• one pair of standard audio cables

Stereo VCR

OUT

AUDIO

From

Antenna

IN from ANT OUT to TV CH 3

CH 4

VIDEO

Note:

For the highest possible picture quality from a DVD player or satellite receiver without component video or HDMI, use an S-video cable. (If your DVD player has component video, see page 12. If your DVD player or satellite receiver has HDMI or DVI, see page

15.) Do not connect both an S-video cable and a

standard video cable between the TV and DVD player/satellite receiver at the same time or the picture performance will be unacceptable.

Do not connect the DVD player/satellite receiver and VCR to the same set of Video inputs on the TV. (See the illustration, which shows the DVD player/satellite receiver connected to VIDEO 1 on the TV, and the VCR connected to VIDEO 2 on the TV.)

IntroductionConnecting

your TV

Using the

remote control

your TV

Setting up

DVD Player

AUDIO

OUT

S-VIDEO

VIDEO

OUTOUT

Satellite Receiver

AUDIO

OUT

From

Satellite

IN from ANT

S-VIDEO

VIDEO

OUTOUT

Dish

Model 46HMX85 is equipped with one HDMI input terminal and one set of AUDIO IN jacks.

Features

Using the TV’s

AppendixIndex

#01E08-16_46/52/62HMX85 5/10/05, 12:39 PM11

Black

(E) 46/52/62HMX85

Connecting a DVD player with ColorStream (component video) and a VCR

This connection allows you to watch DVD, VCR, and TV programs,

IntroductionConnecting

your TV

Using the

Remote Control

your TV

Setting up

and record TV programs. Your TV has ColorStream

your TV to a DVD player with component video (such as a Toshiba DVD player with ColorStream and realism.

–To record one TV program while watching another TV program,

–To record a TV program while watching a DVD, tune the VCR to

You will need:

(component video) inputs. Connecting

) can greatly enhance picture quality

tune the VCR to the channel to record, and tune the TV to the channel to watch. The VCR should be in “TV” mode.

the channel to record, and select ColorStream HD1 on the TV (see “Selecting the antenna input” on page 26).

• two coaxial cables

• one set of standard A/V cables

• one pair of standard audio cables

• one set of component video cables

From Antenna

Stereo VCR

IN from ANT OUT to TV CH 3

CH 4

VIDEO

OUT

AUDIO

Note:

For the highest possible picture quality, use component video cables (or an HDMI cable) between the TV and DVD player.

You can connect component video cables to either set of ColorStream inputs on the TV (HD1 or HD2).

For HDMI or DVI connection, see page 15. The ColorStream HD1/HD2 and HDMI1/2

inputs can be used with Progressive (480p, 720p) and Interlaced (480i, 1080i) scan systems; however, a 1080i signal will provide the best picture performance.

If your DVD player is not compatible with component video, HDMI, or DVI, use the S-video connections (plus the standard audio connections) instead (see page 11).

Features

Using the TV’s

AppendixIndex

AUDIO

OUT

S-VIDEO

COMPONENT VIDEO

RPB

VIDEO

OUT

DVD player with component video

Model 46HMX85 is equipped with one HDMI input terminal and one set of AUDIO IN jacks.

#01E08-16_46/52/62HMX85 5/10/05, 12:39 PM12

Black

(E) 46/52/62HMX85

Connecting a DTV receiver/set-top box with

ColorStream

This connection allows you to watch DTV (digital TV), VCR, and TV programs, and record DTV (composite video only) and TV programs.

Your TV has ColorStream (component video) inputs. Connecting your TV to a DTV receiver with component video can greatly enhance picture quality and realism.

–To record and watch a DTV program, select LINE IN on the

VCR, and select ColorStream HD2 (or VIDEO 1 for a nonColorStream connection) on the TV (see “Selecting the antenna input” on page 26).

–To record a TV program while watching a DTV program, tune the

VCR to the channel to record, and select ColorStream HD2 on the TV.

–To record and watch the same TV program, tune the VCR to the

channel to record, and select VIDEO 1 on the TV.

–To record one TV program while watching another TV program,

tune the VCR to the channel to record, and tune the TV to the channel to watch. The VCR should be in “TV” mode.

You will need:

• three coaxial cables

• two sets of standard A/V cables

• one pair of standard audio cables

• one set of component video cables

From Antenna

(component video) and a VCR

Stereo VCR

Note:

For the highest possible picture quality, use component video cables (or an HDMI cable) between the TV and DTV receiver/set-top box.

You can connect component video cables to either set of ColorStream inputs on the TV (HD1 or HD2).

For HDMI or DVI connection, see page 15. The ColorStream HD1/HD2 and HDMI1/2

inputs can be used with Progressive (480p, 720p) and Interlaced (480i, 1080i) scan systems; however, a 1080i signal will provide the best picture performance.

If your DTV receiver or set-top box is not compatible with component video, HDMI, or DVI, use the S-video connections (plus the standard audio connections) instead (see page 11).

IntroductionConnecting

your TV

Using the

remote control

your TV

Setting up

IN from ANT OUT to TV CH 3

CH 4

From DTV Antenna

Satelite IN

DTV Receiver with component video

Model 46HMX85 is equipped with one HDMI input terminal and one set of AUDIO IN jacks.

S-VIDEO

VIDEO

COMPONENT VIDEO

OUT

AUDIO

PRPBY

VIDEO

OUT

AUDIO

OUT

Features

Using the TV’s

AppendixIndex

#01E08-16_46/52/62HMX85 5/10/05, 12:39 PM13

Black

(E) 46/52/62HMX85

Connecting two VCRs

This connection allows you to record (dub/edit) from one VCR to another VCR while watching a videotape. You also can record from

IntroductionConnecting

your TV

one TV channel while watching another TV channel. You will need:

• two coaxial cables

• two sets of standard A/V cables

From Antenna

VCR1

IN from ANT OUT to TV CH 3

CH 4

VIDEO

OUT

AUDIO

Note:

If you have a VCR (VCR1) with S-video, use S-video cables instead of standard video cables for better picture performance. Do not connect both a standard video cable and an S-video cable to VIDEO 1 (or VIDEO 2) at the same time or the picture performance will be unacceptable.

Do not connect the same VCR to the output and input jacks on the TV at the same time. To dub or edit, VCR 2 must select Line IN, and the TV must select VIDEO 1 (see “Selecting the antenna input” on page 26).

*The VIDEO OUT jack does not output the

POP picture.

** The AUDIO OUT jacks can output the

sound of either the Main or POP picture (see “Selecting the AUDIO OUT sound” on page 58).

Using the

Remote Control

your TV

Setting up

Features

Using the TV’s

VCR2

CH 3 CH 4

VIDEO AUDIO

OUT

Connecting a camcorder

This connection allows you to watch video materials recorded on a camcorder.

You will need:

• one set of standard A/V cables

Camcorder

Note:

If you have a camcorder with S-video, use an S-video cable instead of a standard video cable for better picture performance. Do not connect both a standard video cable and an S-video cable at the same time or the picture performance will be unacceptable.

AppendixIndex

Model 46HMX85 is equipped with one HDMI input terminal and one set of AUDIO IN jacks.

#01E08-16_46/52/62HMX85 5/10/05, 12:39 PM14

Black

(E) 46/52/62HMX85

VIDEO

AUDIO

OUT

Video-3 (side panel)

Connecting an HDMI™ or a DVI device to the HDMI inputs

The HDMI and uncompressed digital video from an HDMI device or uncompressed digital video from a DVI device.

These inputs are designed to accept HDCP material in digital form from EIA/CEA-861/861B– compliant top box or DVD player with HDMI or DVI output).

The HDMI inputs are designed for best performance with 1080i high-definition video signals, but will also accept and display 480i, 480p, and 720p signals.

To connect an HDMI device, you will need:

• one HDMI cable (type A connector)

HDMI device

[1]

inputs on your TV receive digital audio

[2]

[3]

program

[4]

consumer electronic devices (such as a set-

NOTE:

NEVER CONNECT THIS TV TO A

PERSONAL COMPUTER (PC). THIS TV IS NOT

INTENDED FOR USE WITH A PC.

For proper operation, it is recommended that you use a short HDMI cable. You should not encounter difficulty if you use an HDMI cable that is shorter than

16.4 ft (5m). HDMI cable transfers both video and audio. Separate

analog audio cables are not required (see illustration below). Some CDVs (Video CDs) may not output digital audio signals. In that case, you may hear sound by connecting analog audio cables. However, if you connect analog audio cables with this connection, the HDMI terminal on the TV will not receive the HDMI digital audio signal and you will hear analog audio only.

VIDEO AUDIO

OUT

HDMI OUT

[1]

HDMI = High-Definition Multimedia Interface.

[2]

DVI = Digital Video Interface.

[3]

HDCP = High-bandwidth Digital Content Protection.

[4]

EIA/CEA-861/861B compliance covers the transmission of uncompressed digital video with high-bandwidth digital content protection, which is being standardized for reception of high-definition video signals. Because this is an evolving technology, it is possible that some devices may not operate properly with the TV.

To ensure that the HDMI or DVI device is reset properly, it is recommended that you follow these procedures:

•When turning on your electronic components,

turn on the TV first, and then the HDMI or DVI device.

•When turning off your electronic components,

turn off the HDMI or DVI device first, and then the TV.

To connect a DVI device, you will need:

–to–

• one HDMI

DVI adapter cable

(HDMI type A connector)

For proper operation, the length of the HDMI-to-DVI adapter cable should not exceed 9.8 ft (3m). The recommended length is 6.6 ft (2m).

• one pair of standard analog audio cables

An HDMI-to-DVI adapter cable transfers only video. Separate analog audio cables are required (see illustration below).

DVI device

VIDEO AUDIO

OUT

IntroductionConnecting

your TV

Using the

remote control

your TV

Setting up

DVI

OUT

Features

Using the TV’s

You can connect an HDMI cable or an HDMI-to-DVI adapter cable to either HDMI1 or HDMI2 input on the TV. See “Selecting the video input source” on page 50.

HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

#01E08-16_46/52/62HMX85 5/10/05, 12:39 PM15

Black

(E) 46/52/62HMX85

AppendixIndex

Note:

Model 46HMX85 is equipped with one HDMI input terminal and one set of AUDIO IN jacks.

Connecting an audio system

This connection allows you to use an audio amplifier and external speakers and adjust the audio level by using the TV’s remote control.

IntroductionConnecting

your TV

To control the audio, turn on the TV and the stereo amplifier, and turn off the built-in speakers (see “Turning off the built-in speakers” on page 58).

You will need:

Note:

To hear sound when using an external audio amplifier, the volume of both the TV and the amplifier must be set above 0 (zero).

For example, if the volume of the TV is set to 0, you will not be able to hear any sound, even if the volume of the amplifier is at its highest level.

• one pair of standard audio cables

Amplifier

Using the

Remote Control

your TV

Setting up

Features

Using the TV’s

LINE IN LR

AppendixIndex

Model 46HMX85 is equipped with one HDMI input terminal and one set of AUDIO IN jacks.

#01E08-16_46/52/62HMX85 5/10/05, 12:39 PM16

Black

(E) 46/52/62HMX85

Using the remote control

Preparing the remote control for use

Your Toshiba TV remote control has one dedicated TV mode and five universal modes: VCR, Cable/SAT, DVD, Audio1, and Audio2. The target devices and default devices being programmed for each mode are as follows:

Target device/Mode mapping

Mode Device TV Toshiba TV CABLE/SAT Universal Cable, Satellite VCRUniversal VCR, DVD, LD, Cassette DVDUniversal DVD, VCR, LD, Cassette AUDIO1 Universal Audio: Amp., Tuner, Misc.Audio, CD/MD AUDIO2 Universal Audio: CD/MD, Amp., Tuner, Misc.Audio

Default device codes

Mode Default device TV Toshiba TV CABLE/SAT Toshiba Satellite receiver VCRToshiba VCR DVDToshiba DVD AUDIO1 Pioneer Audio receiver AUDIO2 Pioneer LD

Repeatedly press MODE to cycle among the modes. If you own different brands of audio/video devices, you must first program your remote control (see “Programming the remote control for use with your audio/video devices” on page 20).

TV CABLE/SAT VCR DVD AUDIO1 AUDIO2

MODE

PIC SIZE

ACTION

POWER

LIGHT SLEEP

123

456

789

+10

100/

ENT

MODE

Remote control effective range:

16ft (5m)

For optimum performance, aim the remote control directly at the TV and make sure there is no obstruction between the remote control and the TV.

IntroductionConnecting

your TV

Using the

remote control

your TV

Setting up

Installing the remote control batteries

To install the batteries:

1. Slide the battery cover off the back of the remote control.

2. Install two “AA” size alkaline batteries. Match the + and – signs on the batteries to the signs on the battery compartment.

3. Slide the battery cover back on to the remote control until the lock snaps.

Caution:

Never throw batteries into a fire.

Note:

• Be sure to use AA size batteries.

• Dispose of batteries in a designated

disposal area.

• Batteries should always be disposed of with the environment in mind. Always dispose of batteries in accordance with applicable laws and regulations.

• If the remote control does not operate correctly, or if the operating range becomes reduced, replace batteries with new ones.

• When necessary to replace batteries in the remote control, always replace both batteries with new ones. Never mix battery types or use new and used batteries in combination.

• Always remove batteries from remote control if they are dead or if the remote control is not to be used for an extended period of time. This will prevent battery acid from leaking into the battery compartment.

Features

Using the TV’s

AppendixIndex

#01E17-24_46/52/62HMX85 5/10/05, 12:39 PM17

Black

(E) 46/52/62HMX85

Remote Control functional key chart

IntroductionConnecting

your TV

Using the

remote control

your TV

Setting up

Features

Using the TV’s

AppendixIndex

LIGHT Lights the remote control keys, and toggles between enabled and disabled Illumination mode. SLEEP Sleep timer --- --- --- --- --- --- --POWER Power Power Power Power Power Power Power Power 1Digit 1 Digit 1 Digit 1 Digit 1 Digit 1 AV input 1 Digit 1 Digit 1 2Digit 2 Digit 2 Digit 2 Digit 2 Digit 2 AV input 2 Digit 2 Digit 2 3Digit 3 Digit 3 Digit 3 Digit 3 Digit 3 AV input 3 Digit 3 Digit 3 4Digit 4 Digit 4 Digit 4 Digit 4 Digit 4 AV input 4 Digit 4 Digit 4 5Digit 5 Digit 5 Digit 5 Digit 5 Digit 5 CD Digit 5 Digit 5 6Digit 6 Digit 6 Digit 6 Digit 6 Digit 6 Tuner Digit 6 Digit 6 MODE Remote control device mode selection PIC SIZE Selects the TV TV TV TV TV TV TV

7Digit 7 Digit 7 Digit 7 Digit 7 Digit 7 Phono Digit 7 Digit 7 8Digit 8 Digit 8 Digit 8 Digit 8 Digit 8 Cassette Digit 8 Digit 8 9Digit 9 Digit 9 Digit 9 Digit 9 Digit 9 Aux Digit 9 Digit 9 ACTION --- --100/– 100 --- 100/- --- +10 --- --- --0Digit 0 Digit 0 Digit 0 Digit 0 Digit 0 Digit 0 Digit 0, 10 Digit 0 ENT (CH Enter) GUIDE/SETUP INFO/TITLE --- --- INFO --- TITLE= --- --- ---

FAVORITE/ Favorites --SUBTITLE

THEATERLINK/ AUDIO

MENU/ Menu --- Action, --- Menu --- --- --ACTION Menu

yz (FAV yz)Menu select --- Menu select --- Menu select --- --- ---

x • Menu select --- Menu select --- Menu select --- --- ---

ENTER Enter --- Select --- Enter --- --- --VOL

EXIT/ Exit --- Exit --- DVD clear --- --- --DVD CLEAR

INPUT TV/Video TV TV VCR input TV --- TV TV

MUTE RECALL On-screen On-screen On-screen On-screen On-screen --- --- ---

CH RTN/ Previous Previous Previous --- DVD --- --- --DVD RTN channel channel channel return

SLOW/ DIR x--- --- --- --- Slow REV --- --- ---

SKIP/ SEARCH x--- --- --- --- Skip REV

REW VCR VCR VCR Rewind Rewind PAUSE/STEP VCR VCR VCR Pause Pause PLAY VCR VCR VCR Play Play FF VCR VCR VCR Fast FWD Fast FWD --- Fast FWD Fast FWD

Key Label

yz Volume Volume Volume Volume Volume Volume Volume Volume

yz Channel Channel Channel Channel --- Channel --- ---

Toshiba TV Cable Satellite VCR DVD/LD Receiver CD/MD Cassette

(TV) (CBL/SAT) (CBL/SAT) (AUDIO) (AUDIO) (VCR)

image shape.

Action, Menu

--- CH Enter --- --- --- --- --- ---

--- --- Guide --- DVD setup --- --- ---

Favorites

--- --- --- --- Audio --- --- ---

FAV yz

up/down* up/down* up/down* up/down* up/down* up/down* up/down* up/down*

up/down up/down up/down up/down up/down

select Sound mute* Sound mute* Sound mute* Sound mute* Sound mute* Sound mute* Sound mute* Sound mute*

display display display display display

•

--- --- --- Slow FWD Slow FWD --- --- ---

•

--- --- --- --- Skip FWD

--- Menu --- --- ---

Top menu

--- Subtitle --- --- ---

---

Skip FWD Skip REV

Rewind Rewind Pause Pause Play Play

---

#01E17-24_46/52/62HMX85 5/10/05, 12:39 PM18

Black

(E) 46/52/62HMX85

Key Label

TV/VCR VCR AM/FM --- --- --- --- Disc shift AM/FM Disc shift Deck side

DISC A/B switch STOP VCR VCR VCR Stop Stop --- Stop Stop REC

POP CH

SPLIT POP Split TV TV TV TV TV TV TV POP DIRECT CH POP Direct ch FREEZE Still picture TV TV TV TV TV TV TV SWAP POP Swap TV TV TV TV TV TV TV CH SCAN Ch scan TV TV TV TV TV TV TV SOURCE POP Source TV TV TV TV TV TV TV

Notes:

•“---” will send nothing.

•“ TV” will jump to TV.

•“ VCR” will jump to last active VCR or DVD. Active VCR/DVD is defined as the mode that remains for a minimum of 5

seconds, or if a key is pressed in that mode. The VOLUME and MUTE will jump to “TV” by default. When the volume is unlocked, all the devices will have their own volume.

The AUDIO1/2 (Receiver, CD) modes will have their own volume even if Volume Lock is on TV, CABLE/SAT, VCR, or DVD. See “Using the volume lock feature” on page 21.

Press the REC button twice within 5 seconds to record each audio/video source.

Toshiba TV Cable Satellite VCR DVD/LD Receiver CD/MD Cassette

(TV) (CBL/SAT) (CBL/SAT) (AUDIO) (AUDIO) (VCR)

---

VCRVCR VCR Record** --- --- --- Record**

POP channel TV TV TV TV TV TV TV up/down

TV TV TV TV TV TV TV

TV/SAT TV/VCR --- --- --- Reverse

IntroductionConnecting

your TV

Using the

remote control

your TV

Setting up

Features

Using the TV’s

AppendixIndex

#01E17-24_46/52/62HMX85 5/10/05, 12:39 PM19

Black

(E) 46/52/62HMX85

Programming the remote control for use with your audio/video devices

IntroductionConnecting

Device code setup

your TV

Using the

remote control

Searching and sampling the code of a device (8500)

If you do not know the device code for a particular target unit, you can cycle the remote control through the available codes for that device mode and sample the functions to find the code that properly

your TV

Setting up

operates the target device. The keys available to be sampled, provided they are applicable to that mode, are POWER, 1, VOL y, CH y, and PLAY. Invalid keys will be ignored while in program mode.

To cycle through each available device code and sample its functions:

Features

Using the TV’s

AppendixIndex

Note: When a search cycle is completed, the mode indicator will blink

1. Refer to the Device code table on pages 22 – 23 to find the code for the brand of your device.

If more than one number is listed, try each one separately until you find the one that works.

2. Press MODE until the Mode indicator of the device (CABLE/ SAT, VCR, DVD, AUDIO1, AUDIO2) lights up.

3. While holding down the RECALL button, press the Channel Number buttons to enter the four-digit code of your brand of device. If a valid code is entered, the mode indicator will blink twice. If an invalid code is entered, the mode indicator will blink one long blink.

4. Point the remote control at the device and press POWER to test the code.

If the device turns on, you have entered the correct code. If the device does not respond to the remote control, you may

have entered the wrong code. Repeat steps 3 and 4 using another code.

5. Press MODE to select the TV mode to control the TV.

1. Press MODE to select the mode you want to set up.

2. While holding down the RECALL button, press 8 –5 –0 –0. The remote control will enter program mode.

3. Point the remote control at the target device and press POWER (or other function buttons that are available to be sampled).

4. If the device responds to the remote control:

Press RECALL to store the device code. The mode indicator will blink twice and the remote control will exit the program mode.

If the device does not respond to the remote control:

Press y, and then press POWER. Repeat this step until the device responds to the remote control, and then press RECALL.

three times. The remote control will begin to cycle through the available codes again. If no key is pressed within 10 seconds while programming, the remote control will exit the program mode and return to the previous code.

Note:

• Every time you replace the batteries, you must reprogram the remote control.

• Some newer VCRs are capable of working on either of two remote codes. These VCRs have a switch labeled “VCR1/VCR2.”

If your VCR has this kind of switch and does not respond to any of the codes for your VCR brand, set the switch to the other position (VCR1 or VCR2) and reprogram the remote control.

Mode indicator

TV CABLE/SAT VCR DVD AUDIO1 AUDIO2

MODE

PIC SIZE

ACTION

DVD RTN CH RTN

SLOW/DIR

INPUT

POWER

LIGHT SLEEP

123

456

789

+10

100/

FAV

ENTER

FAV

EXIT

DVD CLEAR

RECALL

SKIP/SEARCH

ENT

VOL

MUTE

POWER

Numbers MODE

RECALL

#01E17-24_46/52/62HMX85 5/10/05, 12:39 PM20

Black

(E) 46/52/62HMX85

Using the volume lock feature (8000)

For the TV, CABLE/SAT, VCR, and DVD modes, the volume controls (VOL yz and MUTE) can be programmed (locked) to the selected device mode. This feature does not apply to the AUDIO1/2 modes.

For example, to lock the volume controls to always jump to the CABLE/SAT mode:

1. Repeatedly press MODE to select the CABLE/SAT mode.

2. While holding down the RECALL button, press 8 –0 –0 –0.

3. Press VOL y. The Mode indicator will blink two times (locked).

The following table describes in more detail the Volume Lock implementation.

Volume Locked to

TV (default) CBL/SAT CBL/SAT CBL/SAT CBL/SAT CBL/SAT AUD1 AUD2 VCR VCR VCRVCRVCRAUD1 AUD2 DVD DVD DVD DVD DVD AUD1 AUD2 AUD1 AUD1 AUD1 AUD1 AUD1 AUD1 AUD1 AUD2 AUD2 AUD2 AUD2 AUD2 AUD2 AUD2

TV CBL/SAT VCR DVD AUD1 AUD2

TV TV TV TV AUD1 AUD2

TV CABLE/SAT VCR DVD AUDIO1 AUDIO2

MODE

PIC SIZE

ACTION

DVD RTN CH RTN

SLOW/DIR

LIGHT SLEEP

123

456

789

+10

100/

FAV

ENTER

FAV

EXIT

DVD CLEAR

INPUT

RECALL

SKIP/SEARCH

POWER

IntroductionConnecting

Number MODE

ENT

your TV

VOL

MUTE

VOL y z

RECALL

Using the

remote control

To reset the volume controls to the original device code:

1. While holding down the RECALL button, press 8 –0 –0 –0.

2. Press VOL z. The Mode indicator will blink four times (unlocked).

Operational feature reset (8900)

This feature clears all setup features not related to “Device code set up” and resets the Volume Lock to “TV.”

To reset the features:

While holding down the RECALL button, press 8 –9 –0 –0. The Mode indicator will blink two times, and then pause and blink two more times.

your TV

Setting up

Features

Using the TV’s

AppendixIndex

#01E17-24_46/52/62HMX85 5/10/05, 12:39 PM21

Black

(E) 46/52/62HMX85

Device code table

IntroductionConnecting

your TV

Using the

remote control

your TV

Setting up

Features

Using the TV’s

AppendixIndex

VCR setup codes

Brand Code

ADMIRAL 0135 AIWA 0127, 0132, 0181 AKAI 0129, 0114, 0115,

0116 AUDIO DYNAMIC 0139, 0111 BELL&HOWELL 0105, 0113 BROKSONIC 0120, 0126, 0180 CANON 0123, 0125 CCE 0143 CITIZEN 0106 CRAIG 0105, 0129, 0106 CURTIS MATHES 0145, 0124, 0127 DAEWOO 0143, 0101, 0124,

0175 DBX 0139, 0110, 0111 DIMENSIA 0145 EMERSON 0143, 0126, 0119,

0103, 0125, 0142,

0120, 0118 FISHER 0105, 0108, 0109,

0107, 0113, 0165 FUNAI 0127, 0126, 0120,

0134 GE 0133, 0145, 0124 GO VIDEO 0137, 0151, 0163,

0149, 0150, 0182 GOLDSTAR 0106 GRADIENTE 0170, 0171, 0168,

0134, 0156 HITACHI 0123, 0145, 0100,

0127, 0168 INSTANT REPLAY 0124, 0123 JENSEN 0139 JVC 0139, 0110, 0111,

0134, 0157, 0158,

0184, 0185 KENWOOD 0139, 0110, 0106,

0111 LG 0159 LXI 0127, 0106, 0100,

0107, 0108, 0105,

0109 MAGNAVOX 0131, 0123, 0124,

0173 MARANTZ 0139, 0110, 0111 MARTA 0106 MEMOREX 0124, 0109 MGA 0138, 0140, 0147,

0148, 0141, 0142 MINOLTA 0100, 0145 MITSUBISHI 0138, 0140, 0147,

0148, 0141, 0142,

0161, 0164 MULTITECH 0147, 0127, 0104 NEC 0139, 0110, 0111,

0134 OLYMPIC 0124, 0123 OPTIMUS 0128, 0121, 0135,

0106 ORION 0126, 0120, 0132 PANASONIC 0123, 0124, 0121,

0122 PENNEY 0124, 0100, 0145,

0105, 0139, 0110,

0111 PENTAX 0100, 0111, 0145

PHILCO 0131, 0124, 0127,

0123, 0126, 0120, 0143

PHILIPS 0131, 0123, 0124,

0173 PIONEER 0123 PROSCAN 0145, 0100, 0123,

0124, 0131, 0146,

0101, 0102, 0133 QUASAR 0121, 0122, 0123,

0124 RADIO SHACK 0133, 0124, 0105,

0136, 0109, 0140,

0127 RCA 0133, 0145, 0100,

0123, 0124, 0131,

0146, 0101, 0102,

0170, 0172, 0174,

0176, 0183 REALISTIC 0124, 0105, 0136,

0109, 0140, 0127 SAMSUNG 0137, 0102, 0104,

0133 SAMTRON 0163 SANSUI 0139, 0126, 0120,

0152 SANYO 0105, 0109, 0113 SCOTT 0101, 0102, 0104,

0109, 0138, 0140,

0147, 0148, 0126 SEARS 0105, 0106, 0107,

0108, 0100 SHARP 0135, 0136, 0167,

0162 SHINTOM 0117 SIGNATURE 2000 0127, 0135 SINGER 0117 SONY 0128, 0129, 0130,

0153, 0154, 0155 SV2000 0127 SYLVANIA 0131, 0123, 0124,

0127, 0178 SYMPHONIC 0127, 0168, 0177 TASHIRO 0106 TATUNG 0139, 0110, 0111 TEAC 0139, 0110, 0127,

0111 TECHNICS 0121, 0122, 0123,

0124 TEKNICA 0124, 0127, 0112 THOMSON 0179, 0183 TOSHIBA 0101, 0146, 0166,

0160 VECTOR RESEARCH 0111 WARDS 0135, 0136, 0109,

0144, 0106 YAMAHA 0105, 0139, 0110,

0111 ZENITH 0144, 0106, 0169,

0180

Cable box setup codes

Brand Code

ABC 1124 ARCHER 1132, 1125 CABLEVIEW 1105, 1132 CITIZEN 1122, 1105 CURTIS 1112, 1113 DIAMOND 1124, 1132, 1125 EAGLE 1129 EASTERN 1134 GCBRAND 1132, 1105 GEMINI 1122, 1143 G.I./JERROLD 1119, 1124, 1125,

1126, 1127, 1120, 1121, 1122, 1111, 1123, 1152

HAMLIN 1140, 1141, 1142,

1145, 1118, 1112 HITACHI 1103, 1124 MACOM 1103, 1104, 1105,

1108 MAGNAVOX 1133 MEMOREX 1130 MOVIETIME 1132, 1105 OAK 1139, 1137, 1102 PANASONIC 1109, 1110, 1114,

1151, 1153

PHILIPS 1128, 1129, 1130,

1106, 1107, 1150,

1131 PIONEER 1101, 1116 PULSAR 1105, 1132 PUSER 1132 RCA 1115 REALISTIC 1132 REGAL 1112, 1118, 1140,

1141, 1142, 1145,

1149 REGENCY 1134 REMBRANT 1137, 1132, 1105,

1138 SAMSUNG 1105 S.A. 1111, 1112, 1113 SLMARK 1105, 1101 SPRUCER 1105, 1110 STARGATE 1132, 1105 TELECAPTION 1148 TELEVIEW 1101, 1105 TEXSCAN 1144 TOCOM 1135, 1136, 1147 TOSHIBA 1104, 1146 UNIKA 1132, 1125 UNIVERSAL 1122, 1132 VIDEOWAY 1106 VIEWSTAR 1129, 1130 ZENITH 1117, 1100 ZENITH/DRAKE

SATELLITE 1100

#01E17-24_46/52/62HMX85 5/10/05, 12:39 PM22

Black

(E) 46/52/62HMX85

+ 50 hidden pages