Toshiba 52HM94, 62HM94 User Manual

46HM94 52HM94 62HM94

23566511

Integrated HD DLP

™

Projection Television

WNER’S

ANUAL

Owner’s Record

The model number and serial number are on the back of your TV. Record these numbers in the spaces below. Refer to these numbers whenever you communicate with your Toshiba dealer about this TV.

Model number:

Serial number:

HIGH-DEFINITION TELEVISION

For an overview of steps for setting up

and using your new TV, see page 8.

Compatible with the new Toshiba

Symbio

™

Audio/Video Hard Drive Recorder!

See pages 23 and 49 for details.

HM94(E)001 8/30/04, 10:03 AM1

Dear Customer,

Thank you for purchasing this Toshiba TV. This manual will help you use the many exciting features of your new TV.

Before operating the TV, please read this manual completely, and keep it nearby for future reference.

The lamp in this product has a limited service life. The length of service life varies depending on product use and user settings. If you use the lamp beyond its service life:

• you may notice a reduction in the colors and/or brightness of the picture, at which time you should replace the lamp unit; and

• the strength of the quartz glass in the lamp will be reduced and the lamp may rupture. If the lamp ruptures, the TV will not operate until the lamp unit is replaced.

Note: The lamp unit is designed so broken lamp glass remains securely inside the lamp unit.

See “Lamp unit replacement and care” on pages 98–100.

• Dispose of the used lamp unit by the approved method for your area.

Note: The lamp unit contains mercury.

Disposal of mercury may be regulated due to environmental considerations. For disposal or recycling information, contact your local authorities or the Electronic Industries Alliance (www.eiae.org).

Safety Precautions

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This applies to all items

except those specified on pages 98–100 of this manual.

Child Safety

It Makes A Difference Where Your TV Stands

Congratulations on your purchase! As you enjoy your new TV, keep these safety tips in mind:

The Issue

 If you are like most consumers, you have a TV in your home. Many homes,

in fact, have more than one TV.

 The home theater entertainment experience is a growing trend, and larger

TVs are popular purchases; however, they are not always supported on the proper TV stands.

 Sometimes TVs are improperly secured or inappropriately

situated on dressers, bookcases, shelves, desks, audio speakers,

chests, or carts. As a result, TVs may fall over, causing

unnecessary injury.

We Care!

 The consumer electronics industry is committed to making home entertainment enjoyable and safe.

 The Consumer Electronics Association formed the

Home Entertainment Support Safety Committee, comprised

of TV and consumer electronics furniture manufacturers, to

advocate children’s safety and educate consumers and their

families about television safety.

Tune Into Safety

 One size does NOT fit all! Use appropriate furniture large enough to

support the weight of your TV (and other electronic components).

 Use appropriate angle braces, straps, and anchors to secure your furniture

to the wall (but never screw anything directly into the TV).

 Carefully read and understand the other enclosed instructions for proper

use of this product.

 Do not allow children to climb on or play with furniture and TVs.  Avoid placing any item on top of your TV (such as a VCR, remote control,

or toy) that a curious child may reach for.

 Remember that children can become excited while watching a program

and can potentially push or pull a TV over.

 Share our safety message about this hidden hazard of

the home with

your family and friends. Thank you!

2500 Wilson Blvd. Arlington, VA 22201 U.S.A. Tel. 703-907-7600 Fax 703-907-7690 www.CE.org

CEA is the Sponsor, Producer and Manager of the International CES

NOTE TO CATV INSTALLERS IN THE U.S.A.

This is a reminder to call the CATV system installer’s attention to Article 820-40 of the NEC, which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. For additional antenna grounding information, see items 27 and 28 on page 4.

NOTICE OF POSSIBLE TV STAND INSTABILITY

CAUTION: This television is for use only with the Toshiba stand listed below. Use with other

carts or stands is capable of resulting in instability

causing possible injury.

Television Stand Model 46HM94 ST4694, ST4684 52HM94 ST5294, ST5284 62HM94 ST6294, ST6284

In Canada, please contact your authorized Toshiba dealer or visit the Toshiba Canada web site at www.toshiba.ca to determine the appropriate stand for your television.

Lamp Unit Replacement

CAUTION: HOT SURFACE!

The temperature of the lamp immediately after use exceeds

392°F (200°C). Touching the lamp before it has cooled will result in severe burns. ALLOW THE LAMP TO COOL FOR AT LEAST ONE (1) HOUR BEFORE REPLACING IT.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle, is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING

RISK OF ELECTRIC SHOCK!

DO NOT OPEN.

NOTE: NEVER CONNECT THIS TV TO A PERSONAL COMPUTER (PC).

THIS TV IS NOT INTENDED FOR USE WITH A PC.

HM94(E)002-04 10/27/04, 3:51 PM2

Installation, Care, and Service

Installation

Follow these recommendations and precautions and heed all warnings when installing your TV:

17) Never modify this equipment. Changes or modifications may void: a) the warranty, and b) the user’s authority to operate this equipment under the rules of the Federal Communications Commission.

18) DANGER: RISK OF SERIOUS PERSONAL

INJURY, DEATH, OR EQUIPMENT DAMAGE! Never place the TV on

an unstable cart, stand, or table. The TV may fall, causing serious personal injury, death, or serious damage to the TV.

19) Never place or store the TV in direct sunlight; hot, humid areas; areas subject to excessive dust or vibration; or locations with temperatures at or below 41°F (5°C).

20) Always place the TV on the floor or a sturdy, level, stable surface that can support the weight of the unit.

21) Never expose the apparatus to dripping or splashing or place items such as vases, aquariums, any other item filled with liquid, or candles on top of the TV.

22) Always place the back of the television at least one (1) inch away from any vertical surface (such as a wall) to allow proper ventilation.

23) Never block or cover the slots or openings in the TV cabinet back, bottom, and sides. Never place the TV:

• on a bed, sofa, rug, or similar surface;

• too close to drapes, curtains, or walls; or

• in a confined space such as a bookcase, built-in cabinet,

or any other place with poor ventilation.

The slots and openings are provided to protect the TV from overheating and to help maintain reliable operation of the TV.

24) Never allow anything to rest on or roll over the power cord, and never place the TV where the power cord is subject to wear or abuse.

25) Never overload wall outlets and extension cords.

26) Always operate this equipment from a 120 VAC, 60 Hz power source only.

Important Safety Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with a dry cloth.

7) Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being

walked on or pinched, particularly at plugs, convenience receptacles, and the point where it exits the apparatus.

11) Only use attachments/accessories specified by the

manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use

caution when moving the cart/apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or

when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, or the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. This applies to all items except those

specified on pages 98–100 of this manual.

15) CAUTION: To reduce the risk of electric shock, do not use the polarized plug with an extension cord, receptacle, or other outlet unless the blades can be inserted completely to prevent blade exposure.

16) WARNING: This product contains a lamp to project

the picture, and requires special safety precautions:

• See pages 98–100 for instructions on lamp unit

replacement and care.

• DO NOT attempt to service this product except as

specified on pages 98–100. The only user-serviceable item in this product is the lamp unit.

Wide plug

(continued on next page)

HM94(E)002-04 8/30/04, 10:58 AM3

Ground clamp

Antenna discharge unit (NEC Section 810-20)

Grounding conductors (NEC Section 810-21)

Power service grounding electrode system (NEC Art 250 Part H)

Ground clamps

Antenna lead-in wire

Electric service equipment

Installation

(continued from previous page)

27) Always make sure the antenna system is properly grounded to provide adequate protection against voltage surges and built-up static charges (see Section 810 of the National Electric Code).

28) DANGER: RISK OF SERIOUS PERSONAL

INJURY OR DEATH!

• Use extreme care to make sure you are never in

a position where your body (or any item you are in contact with, such as a ladder or screwdriver) can accidentally touch overhead power lines. Never locate the antenna near overhead power lines or other electrical circuits.

• Never attempt to install any of the following during lightning activity: a) an antenna system; or b) cables, wires, or any home theater component connected to an antenna or phone system.

Care

For better performance and safer operation of your TOSHIBA TV, follow these recommendations and precautions:

29) Always sit approximately 10–25 feet away from the TV and as directly in front of it as possible. The picture can appear dull if you sit too far to the left or right of the TV, or if sunlight or room lights reflect on the screen. Turn the TV off to check for reflections on the screen, and then remove the source of reflections while viewing the TV.

30) Always unplug the TV before cleaning. Never use liquid or aerosol cleaners. Clean only with a soft, dry cloth. Do not spray volatile compounds such as insecticide on the cabinet. This may cause a discoloration or damage of the cabinet.

31) WARNING: RISK OF ELECTRIC SHOCK!

Never spill liquids or push objects of any kind into the TV cabinet slots.

32) If the air temperature rises suddenly (for example, when the TV is first delivered), condensation may form on the lenses. This can make the picture appear distorted or the color appear faded. If this happens, turn off the TV for 6 to 7 hours to allow the condensation to evaporate.

Care

(continued from previous column)

33) For added protection of your TV from lightning and power surges, always unplug the power cord and disconnect the antenna from the TV if you leave the TV unattended or unused for long periods of time.

) During normal use, the TV may make occasional snapping

or popping sounds. This is normal, especially when the unit is being turned on or off. If these sounds become frequent or continuous, unplug the power cord and contact a Toshiba Authorized Service Center.

35)

Special care for DLP

(digital light processing) units:

•

Lamp—The lamp in this product has a limited service life.

The length of service life varies depending on product use or user settings. If you use the lamp beyond its service life:

- you may notice a reduction in the colors and/or

brightness of the picture, at which time you should replace the lamp unit; and

- the strength of the quartz glass in the lamp will be

reduced and the lamp may rupture. If the lamp ruptures, the TV will not operate until the lamp unit is replaced.

See “Lamp unit replacement and care” on pages 98–100.

Note:

• The lamp unit is designed so broken lamp glass remains

securely inside the lamp unit.

• The lamp unit contains mercury. Disposal of

mercury may be regulated due to environmental

considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance (www.eiae.org).

• Dispose of the used lamp unit by the approved method for

your area.

Service

) WARNING: RISK OF ELECTRIC SHOCK!

Never attempt to service the TV yourself,

except as specified on pages 98–100. Opening and removing the covers may expose you to dangerous voltage or other hazards. Failure to follow this WARNING may result in death or serious injury. Refer all servicing not specified in this manual to a Toshiba Authorized Service Center.

37) If you have the TV serviced:

• Ask the service technician to use only replacement parts

specified by the manufacturer.

• Upon completion of service, ask the service technician to

perform routine safety checks to determine that the TV is in safe operating condition.

38)When the TV reaches the end of its useful life, ask a qualified service technician to properly dispose of the TV.

Note: The lamp unit contains mercury. Disposal of mercury may be regulated due to environmental considerations. Dispose of the used lamp unit by the approved method for your area. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance (www.eiae.org).

HM94(E)002-04 8/30/04, 10:58 AM4

Contents

Important Safety Information............................................. 2-4

Important notes about your DLP projection TV ................. 5

Chapter 1: Introduction .......................................................... 7

Welcome to Toshiba ........................................................... 7

Features of your new TV .................................................... 7

Overview of steps for installing, setting up, and

using your new TV ...................................................... 8

Chapter 2: Connecting your TV ............................................ 9

TV front touchpad and side panel controls

and connections ............................................................. 9

TV back panel connections ................................................ 10

Overview of cable types ...................................................... 11

About the connection illustrations ...................................... 12

Connecting a digital CableCARD

™

.................................... 12

Connecting a VCR and antenna or Cable TV

(no Cable box) ............................................................... 13

Connecting a camcorder ..................................................... 13

Connecting a VCR and Cable box ..................................... 14

Connecting a VCR and satellite receiver ............................. 15

Connecting a DVD player with S-video, a VCR,

and a Cable box .............................................................. 16

Connecting a DVD player with ColorStream

(component video) and a VCR ....................................... 17

Connecting two VCRs ....................................................... 18

Connecting an HDMI

™

or a DVI device to the

HDMI input .................................................................. 19

Connecting a digital audio system ...................................... 20

Connecting an analog audio system .................................... 20

Controlling infrared remote-controlled devices

through the TV (IR pass-through).................................. 21

Connecting IEEE-1394 video devices................................. 22

Using analog-compatible IEEE-1394 devices.................. 22

Supported signals ........................................................... 22

Using TheaterNet on-screen device control .................... 22

Connecting an AVHD or D-VHS recorder .................... 23

IEEE-1394 device initialization ...................................... 23

IEEE-1394 device management ..................................... 24

G-LINK

™

connection ........................................................ 25

Chapter 3: Using the remote control ................................. 26

Learning about the remote control ..................................... 26

Installing the remote control batteries................................. 27

Using the remote control MODE button to control

your other devices........................................................... 27

Remote Control functional key chart ................................. 28

Programming the remote control to operate

your other devices........................................................... 30

Multi-brand remote control device codes............................ 32

Chapter 4: Menu layout and navigation ........................... 34

Main menu layout .............................................................. 34

Setup/Installation menu layout........................................... 35

Navigating the menu system............................................... 35

Chapter 5: TV Guide On Screen™ system setup ............. 36

TV Guide On Screen reminder .......................................... 39

Chapter 6: Setting up your TV ............................................. 40

Selecting the menu language............................................... 40

Configuring the antenna input sources ............................... 40

Programming channels into the TV’s channel memory....... 41

Programming channels automatically .......................... 41

Manually adding and deleting channels in the

channel memory ..................................................... 42

Important notes about your DLPTM projection TV

1) The light source for this TV is a projection lamp unit with a limited service life. When the lamp wears out, the picture may become dark or black, or the lamp may fail, at which time you must replace the lamp unit. See “Lamp unit replacement and care” on pages 98–100.

2) Each time you turn on the TV, it may take several seconds to go from no picture to full picture brightness.

3) The display on this TV is manufactured using a chip that may contain up to 1.3 million microscopic mirrors. Each of these micromirrors measures less than one-fifth the width of a human hair and represents a single pixel on the television display. These micromirrors are mounted on tiny hinges that enable them to titlt either toward the light source (ON) or away from it (OFF). Occasionally, one of these mirrors may become inoperative, creating a light or dark pixel on the projection surface. This is a structural property of DLP™ projection TV technology, and is not a sign of malfunction. Such pixels are not visible when the picture is viewed from a normal viewing distance (see item 29 on page 4).

4) Depending on the media you are viewing, it is possible, although unlikely, that a limited number of viewers may see a “rainbow effect” on the screen, which can, in rare instances, result in eye

fatigue. This is a rare occurrence related to technology of this type, and is not a sign of TV malfunction.

5) Always sit approximately 10–25 feet away from the TV and as directly in front of it as possible. The picture quality may be affected by your viewing position and length of viewing time. If you sit too closely to the TV for too long, you may suffer from eye fatigue. See item 29 on page 4.

6) This TV contains several cooling fans to moderate the

internal temperature. You may be able to hear the fans

for several minutes after the TV is turned off. This is a function of the Quick Restart Low Power Shutdown mode and is not a sign of TV malfunction. You can set the Quick Restart feature to stop the fans as soon as the TV is turned off. See “Selecting the Quick Restart feature” on page 50.

7) The green and red LED lights on the control touchpad (on the lower right corner of the TV screen) indicate your TV’s current status. If either light flashes, see “LED indications” on page 94 for details.

8) Review all safety and operating information in this owner’s manual before you use your TV.

_______________ The DLP logo and DLP medallion are trademarks of Texas Instruments.

(Continued on next page)

HM94(E)005-06(Notes&TOC) 11/3/04, 10:48 AM5

Contents

(Continued from previous page)

Programming your favorite channels .................................. 43

Setting up and using TheaterNet

™

on-screen

device control ................................................................. 44

Setting up TheaterNet ................................................. 44

Using the TheaterNet control icons............................. 45

TheaterNet IR device codes .................................. 46–48

Setting the AVHD device skip time .................................... 49

Setting the HDMI

™

audio mode ........................................ 49

Setting the time and date .................................................... 49

Viewing the CableCARD™ menu ...................................... 50

Setting the Quick Restart feature ........................................ 50

Viewing the digital signal meter ......................................... 51

Viewing the system status ................................................... 51

Chapter 7: Using the TV Guide On Screen™

interactive program guide ............................................... 52

Setting up the TV Guide On Screen system ....................... 52

Navigating the TV Guide On Screen system ...................... 53

TV Guide On Screen remote control functions .......... 53

Video Window ........................................................... 54

Panel Menus ............................................................... 54

Info Box ...................................................................... 55

TV Guide On Screen Icons......................................... 55

TV Guide On Screen Services ............................................ 56

LISTINGS screen ....................................................... 56

SEARCH screen.......................................................... 57

RECORDINGS screen ............................................... 59

SCHEDULE screen .................................................... 60

Record features ........................................................... 60

Remind features .......................................................... 62

SETUP screen ............................................................. 64

Change system settings .......................................... 64

Change channel display ......................................... 64

Change default options .......................................... 65

Chapter 8: Using the TV’s features .................................... 66

Selecting the video input source to view ............................. 66

Labeling the video input sources ......................................... 67

Tuning channels ................................................................. 68

Tuning to the next programmed channel .................... 68

Using SpeedSurf to change to a specific

programmed channel .............................................. 68

Tuning to a specific channel (programmed or

unprogrammed) ...................................................... 68

Switching between two channels using

Channel Return ...................................................... 68

Switching between two channels using SurfLock

™

............................................................... 68

Selecting the picture size ..................................................... 69

Natural picture size ..................................................... 69

TheaterWide

1 picture size ........................................ 70

TheaterWide

2 picture size ........................................ 70

TheaterWide

3 picture size ........................................ 70

Full picture size ........................................................... 70

Scrolling the TheaterWide

picture .................................... 71

Using the auto aspect ratio feature ...................................... 71

Selecting the cinema mode (480i signals only) .................... 72

Selecting the lamp mode .................................................... 72

Using the POP features ...................................................... 73

Using the POP double-window feature ....................... 73

Switching the speaker audio (main or POP) ................ 74

Freezing the main picture in the

POP double-window .............................................. 74

POP double-window aspect ratio ................................ 75

Using the favorite channel scan feature........................ 75

Adjusting the picture .......................................................... 76

Selecting the picture mode .......................................... 76

Adjusting the picture quality ....................................... 76

Resetting the picture settings ....................................... 76

Using CableClear

™

DNR (digital noise reduction) ...... 77

Selecting the color temperature ................................... 77

Resetting the advanced picture settings ....................... 77

Using the closed caption mode ........................................... 78

Advanced closed captions ............................................ 78

Digital closed captions ................................................ 78

Adjusting the audio ............................................................ 79

Muting the sound ....................................................... 79

Digital audio selector .................................................. 79

Selecting stereo/SAP broadcasts................................... 79

Adjusting the audio quality ......................................... 80

Using the StableSound

™

feature .................................. 80

Resetting your audio adjustments................................ 80

Using the SRS WOW

™

surround sound feature .......... 81

Turning off the built-in speakers ................................. 81

Selecting the optical audio output format ................... 81

Using the memory card JPEG picture viewer/MP3 audio

player ............................................................................. 82

Memory card specifications ......................................... 82

Using the JPEG picture viewer.................................... 83

Using the MP3 audio player ....................................... 84

Memory card care and handling .................................. 85

Using the Game Mode feature............................................ 85

Setting the ON/OFF timer ................................................ 86

Setting the sleep timer ........................................................ 86

Displaying TV setting information on-screen ..................... 87

Understanding the auto power off feature........................... 87

Understanding the last mode memory feature .................... 87

Chapter 9: Using the Locks menu...................................... 88

Entering the PIN code ....................................................... 88

If you cannot remember your PIN code ............................. 88

Changing your PIN code ................................................... 88

Blocking TV programs and movies by rating (V-Chip) ......... 89

Blocking channels............................................................... 90

Unlocking programs temporarily ........................................ 90

Locking video inputs .......................................................... 90

Using the GameTimer

™

..................................................... 91

Using the front panel lock feature....................................... 91

Chapter 10: Troubleshooting ............................................... 92

General troubleshooting ..................................................... 92

LED indications ................................................................. 94

TV Guide On Screen FAQs ......................................... 95–97

Chapter 11: Appendix ........................................................... 98

Lamp unit replacement .............................................. 98–100

Specifications ................................................................... 101

Limited United States Warranty ....................................... 102

Limited Canada Warranty ................................................ 103

Index ....................................................................................... 106

HM94(E)005-06(Notes&TOC) 8/30/04, 1:01 PM6

Thank you for purchasing this Toshiba TV, one of the most innovative DLP™ projection TVs on the market. The goal of this manual is to guide you through setting up and operating your TV as quickly as possible.

• This manual applies to models 46HM94, 52HM94, and 62HM94. Before you start reading, check the model number on the back of your TV.

•Instructions in this manual are based on using the remote control. You also can use the controls on the TV front touchpad if they have the same name as those referred to on the remote control.

• The side panel and back panel provide terminals for connecting other equipment to your TV. See page 9 for front touchpad and side panel details. See page 10 for back panel details. See pages 12–25 for instructions on connecting other devices to your TV.

• Please read all safety and operating instructions in this manual carefully, and keep this manual for future reference.

Introduction

Welcome to Toshiba

Features of your new TV

The following are just a few of the many exciting features of your new Toshiba widescreen, integrated HD, DLP projection TV:

•

Integrated digital tuning (8VSB ATSC and QAM)

eliminates the need for a separate digital converter set-top box (in most cases).

•

TV Guide On Screen

no-fee interactive program guide (Chapters 5 and 7).

•

Digital CableCARD

™

module slot for viewing encrypted digital Cable TV programs (page 12).

•

Digital recording

by connecting a D-VHS digital recording device or a Toshiba Symbio™ 160HD4 Audio/Video Hard Drive

Recorder to one of the IEEE-1394 jacks. You can record high definition and standard definition material from either tuner (page 23).

•

Memory card slots

[

SD™, SmartMedia,™ MMC,

Memory Stick™ (Pro), CompactFlash®] for viewing JPEG files as a “slide show”

(page 83) and for playing MP3 files (page 84).

•

TheaterNet

™

icons for on-screen control of external

and

IEEE-1394

devices (page 44).

•

Two IEEE-1394 ports

for multi-device connection and control (page 22).

•

HDMI/DVI

digital, high-definition multimedia interface (page 19).

•

Two sets of ColorStream® HD

high-resolution component video inputs (pages 15 and 17).

•

Dolby® Digital*

(page 20) and

SRS® WOW

(page 81) audio technologies.

•

Digital Audio Out

optical audio connection (page 20).

•

Game Mode

feature for shorter frame delays when playing high-action video games (page 85).

•

CableClear™ DNR

digital picture noise reduction (page 77).

•Double-window

POP

(page 73) and multi-window

Favorites

(page 75) features.

______________

In the United States, TV GUI DE and other related marks are registered marks of Gemstar-TV Guide International, Inc. and/or one of its affiliates. In Canada, TV GUIDE is a registered mark of Transcontinental Inc., and is used under license by Gemstar-TV Guide International, Inc. The TV Guide On Screen system is manufactured under license from Gemstar-TV Guide International, Inc. and/or one of its affiliates. The TV Guide On Screen system is protected by one or more of the following issued United States patents: 6,498,895, 6,418,556, 6,331,877, 6,239,794, 6,154,203, 5,940,073, 4,908,713, 4,751,578, 4,706,121.

GEMSTAR-TV GUIDE INTERNATIONAL, INC. AND/OR ITS RELATED AFFILIATES AND/OR TOSHIBA AMERICA CONSUMER PRODUCTS, L.L.C. ARE NOT IN ANY WAY LIABLE FOR THE ACCURACY OF THE PROGRAM SCHEDULE INFORMATION PROVIDED BY THE TV GUIDE ON SCREEN SYSTEM. IN NO EVENT SHALL GEMSTAR-TV GUIDE INTERNATIONAL, INC. AND/OR ITS RELATED AFFILIATES AND/OR TOSHIBA AMERICA CONSUMER PRODUCTS, L.L.C. BE LIABLE FOR ANY AMOUNTS REPRESENTING LOSS OF PROFITS, LOSS OF BUSINESS, OR INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH THE PROVISION OR USE OF ANY INFORMATION, EQUIPMENT, OR SERVICES RELATING TO THE TV GUIDE ON SCREEN SYSTEM.

•A recording device is required for recording. Over-the-air or cable access to stations carrying TV Guide On Screen data is required for the TV Guide On Screen system to operate. TV Guide On Screen data is not provided by Toshiba America Consumer Products, L.L.C. The provider of the data may elect to discontinue the service or it may cease to be (or never be) available in your area. In any of these circumstances, the TV Guide On Screen feature will not function.

•This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision and is intended for home and other limited pay-per-view uses only, unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

•SRS WOW, SRS and the

logo are trademarks of SRS Labs, Inc. SRS WOW technology is incorporated under license from SRS Labs, Inc.

•

Manufactured under license from Dolby Laboratories. Dolby and the double-D logo are registered trademarks of Dolby Laboratories.

• CableCARD is a trademark of Cable Television Laboratories, Inc.

• SmartMedia is a registered trademark of Toshiba Corporation.

•SD is a trademark of SD Card Association.

•MMC and MultiMediaCard are trademarks of Infineon Technologies AG and licensed to MMCA (MultiMediaCard Association).

•Memory Stick is a trademark of Sony Corporation.

•Toshiba is an authorized licensee of the CompactFlash

and CF logo® registered trademarks.

See “Important notes about your

DLP

™

projection TV” on page 5.

HM94(E)007-08(1-Intro) 8/30/04, 1:41 PM7

1. Carefully read the important safety, installation, care, and service information on pages 2–5. Keep this manual for future reference.

2. Observe the following when choosing a location for the TV:

•

Place the TV on the floor or on the optional TV stand listed in the “Specifications” section (page 101).

Overview of steps for installing, setting up, and using your new TV

Follow these steps to set up your TV and begin using its many exciting features.

Chapter 1: Introduction

Note:

If you sell or transfer this television to a third party, be sure to reset the PIN code as described on page 88 under the heading, “If you cannot remember your PIN code.”

• Place the TV in a location where light does not reflect on the screen.

• Place the TV far enough from walls and other objects to allow proper ventilation. Inadequate ventilation may cause overheating, which will damage the TV. THIS TYPE OF

DAMAGE IS NOT COVERED UNDER THE TOSHIBA WARRANTY.

• Read “Installation” on pages 3–4.

• Read “Important notes about your DLP TV” on page 5.

3. Do not plug in any power cords until AFTER you have

connected all cables and devices to your TV.

4. BEFORE connecting cables or devices to the TV, learn the functions of the TV’s connections and controls (pages 9 and 10).

5. Connect your other electronic device(s) to the TV (pages 12–25).

6. Connect the G-LINK™ cable (either one of the enclosed IR blaster cables) from your VCR and/or Cable box (if applicable) to the G-LINK jack so you can use the TV Guide On Screen

features (applies to VCRs and cable boxes only). See page 25.

7. Install the batteries in the remote control (page 27).

8. See “Learning about the remote control” (page 26) for an overview of the buttons on the remote control.

9. Program the remote control to operate your other device(s) (pages 27–33).

10. AFTER connecting all cables and devices, plug in the power cords for your TV and other devices.

11. After you plug in the TV power cord, the green LED (on the TV front touchpad, to the left of the POWER button) will blink 3 times. Wait about 30 seconds until the green LED lights continuously and then press POWER on the TV front touchpad or remote control.

See “LED indications” on page 94.

12. See “Menu layout and navigation” for a quick overview of navigating the TV’s menu structure (pages 34–35).

13. See Chapter 5 for details on setting up the TV Guide On Screen

system (if available in your area).

Note:

The TV Guide On Screen program guide opens automatically when you turn on the TV. To disable this feature:

1) Press TV GUIDE on the remote control to open the TV Guide On Screen system (if it is not already open).

2) Use the x • buttons to select the SETUP menu.

3) Use the yz buttons to select CHANGE DEFAULT OPTIONS, and then press ENTER.

4) Use the yz buttons to select GENERAL DEFAULT OPTION, and then press ENTER.

5) Set the AUTO GUIDE option to OFF.

6) Use the yz buttons to select DONE, and then press ENTER.

14. See Chapter 7 for details on using the TV Guide On Screen™ program guide (if available in your area).

•When using the TV Guide On Screen system to record a program for the first time, it is recommended that you perform a test recording to make sure your system is set up properly.

•

If the TV power cord is unplugged for an extended period of time, it may take up to 24 hours with the TV in standby mode (power cord plugged in and power OFF) to download the entire TV Guide On Screen program schedule. Be sure to follow the instructions under “TV Guide On Screen Reminder” on page 39.

15. Program channels into the TV’s channel memory

(page 41).

16. Set up the TheaterNet™ on-screen device control feature (if applicable to your particular home theater system components) (page 44).

17. For details on using the memory card JPEG picture

viewer and MP

audio player, see page 82.

18. For details on using the TV’s features, see Chapter 8.

19. For help, refer to the Troubleshooting Guide (Chapter

10).

20. For technical specifications, see Chapter 11.

21. For warranty information, see Chapter 11.

22. Enjoy your new TV!

NOTICE OF POSSIBLE TV STAND INSTABILITY

DANGER: RISK OF SERIOUS PERSONAL INJURY OR DEATH! Use this TV only with the TOSHIBA TV stand

listed in the “Specifications” section (page 101). Use with other stands may result in instability, causing possible injury or death.

HM94(E)007-08(1-Intro) 8/30/04, 1:41 PM8

Reset button

MENUVOLUMECHANNELEXITTV/VIDEO POWER

TV front touchpad and side panel controls and connections

Connecting your TV

MENUVOLUMECHANNELEXITTV/VIDEO POWER

TV/VIDEO

EXIT

zyx •

Channel

zy7Volume

x •

Green/Red LEDs

Front touchpad*

Remote sensor

(behind the screen)

— Point the remote control toward this area of the TV screen. See “Remote control effective range” on page 26.

TV/VIDEO

— Repeatedly press to change the source you are viewing (ANT 1, ANT 2, VIDEO 1, VIDEO 2, VIDEO 3, HDMI, ColorStream HD1, ColorStream HD2).

EXIT

— Press to close an on-screen menu instantly.

ARROWS

zyx • — When a menu is on-screen, these buttons function as down/up/left/right menu navigation buttons.

— Press to access the menu system (see page 34). When a menu is on-screen or the TV Guide On Screen program guide is open, this button functions as the ENTER button.

POWER

— Press to turn the TV on and off.

CHANNEL

yz — When no menu is on-screen, these

buttons change the channel (programmed channels only; see page 41). When a menu is on-screen, these buttons function as up/down menu navigation buttons.

VOLUME

x • — When no menu is on-screen, these

buttons adjust the volume level. When a menu is on-screen, these buttons function as left/right menu navigation buttons.

Green and Red LEDs

— When green lights solid (not blinking), it indicates that the TV power cord is plugged in and the power is OFF. This is called standby mode.

Note: When you first plug in the power cord, the green LED will blink 3 times. After approximately 30 seconds, the green LED will light continuously, at which point you can press POWER to turn ON the TV.

When red lights solid (not blinking), it indicates that the TV power cord is plugged in and the POWER is ON.

See “LED indications” on page 94 for additional information.

RESET

— If the TV stops responding to the controls on the remote control or TV front panel and you cannot turn off the TV, press this button to reset the TV.

Note: The RESET button is recessed, so you will need to use the end of a paper clip or similar object to press the button.

!¡

VIDEO-3

— The side panel A/V connections are referred to as “VIDEO 3” and include standard A/V connections plus optional S-video. (The VIDEO 1 and VIDEO 2 A/V connections are on the TV’s back panel; see page 10.)

!™

Memory card slots

— Insert a memory card into one of the memory card slots to view JPEG files (such as photos) as a “slide show” on your TV or listen to MP3 audio files (see page 82).

Remote sensor

POWER

Front of TV

{

Memory card

slots

!™

*Gently touch the printed keys on the touchpad.

Side panel

Right side of TV

VIDEO-3 IN

!¡

HM94(E)009-11(2A-Cnct) 8/30/04, 1:39 PM9

OUT

AUDIO

S-VIDEO

VIDEO 1 VIDEO 2

OUT 1

G-LINK

HDMI IN

DIGITAL

AUDIO OUT

ANT (75

)

ANT1

(CABLE)

ANT2

CableCARD™

COLOR STREAM

HD-1

COLOR

STREAM

HD-2

VAR

AUDIO

TheaterNet

OUT 2

S-VIDEO

IEEE1394

EJECT

L/ MONO

AUDIO

VIDEO

L/ MONO

AUDIO

VIDEO

L/ MONO

AUDIO

VIDEO

AUDIO

TheaterNet

___________

HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing, LLC.

CableCARD is a trademark of Cable Television Laboratories, Inc.

TV back panel connections

For an explanation of cable types, see page 11.

1 ANT-1 (CABLE) IN and ANT-2 IN — Two inputs that

support analog (NTSC) and digital (ATSC) off-air antenna signals and analog and digital (QAM) Cable TV signals.

Note: If you have an antenna only, connect it to ANT-1. If you have both cable TV and an antenna, connect the cable TV to ANT-1 and the antenna to ANT-2.

2 VIDEO 1 IN and VIDEO 2 IN — Two sets of standard

(composite) video and standard audio inputs plus optional S-video inputs for connecting devices with composite video or S-video output.

NOTE: Standard (composite) video and S-video cables carry only video information; separate audio cables are required for a complete connection.

3 ColorStream® HD-1 and ColorStream® HD-2 — Two sets

of ColorStream

high-definition component video and standard stereo audio inputs for connecting devices with component video output, such as a Toshiba DVD player with ColorStream.

See pages 15 and 17.

Note: Component video cables carry only video information; separate audio cables are required for a complete connection.

4 A/V OUT — Standard composite video and analog audio

outputs for connecting a VCR for editing and dubbing. See page 18 for details.

5 Variable Audio OUT — Standard analog audio outputs for

connecting an analog amplifier with external speakers. See page 20.

6 Digital Audio OUT — Optical audio output in Dolby

Digital or PCM (pulse-code modulation) format for connecting an external Dolby Digital decoder, amplifier, AV r eceiver, or home theater system with optical audio input. See page 20.

7 G-LINK

™

— For use with one of the enclosed IR blaster/

G-LINK cables to enable the TV Guide On Screen

recording features. See page 25.

8 TheaterNet

™

(IR) OUT — For controlling infrared

remote-controlled devices through the TV. You can connect up to two devices with either one of the enclosed IR blaster cables, and then control the devices using the TV’s IR passthrough or TheaterNet

™

(on-screen device control) features.

See pages 21 and 44.

9 Standard Audio IN — For use when connecting a DVI

device with analog audio output to the HDMI input. See page 19. Also see item 10 below.

0 HDMI

™

IN — High-Definition Multimedia Interface input receives digital audio and uncompressed digital video from an HDMI device or uncompressed digital video from a DVI device. See page 19.

NOTE: NEVER CONNECT THIS TV TO A PERSONAL COMPUTER (PC). This TV is not intended for use with a PC.

!¡ IEEE-1394 — Two bi-directional digital IEEE-1394 ports

for connecting multiple devices with compressed digital video. Because these ports are bi-directional, they can be used for playback and recording. You can control your IEEE-1394 devices using the TV’s TheaterNet on-screen control icons. See pages 21–24 and 44.

NOTE:

• IEEE-1394 cable carries both audio and video information;

no separate audio cables are required for a complete connection.

•NEVER CONNECT THIS TV TO A PERSONAL COMPUTER (PC). This TV is not intended for use with a PC.

!™ CableCARD™ slot — For use with a digital security card

and digital cable TV service (provided by your local cable operator) to view encrypted digital programming. See pages 12 and 50.

Chapter 2: Connecting your TV

{

!™

{

!¡

OUT

AUDIO

S-VIDEO

VIDEO 1 VIDEO 2

OUT 1

G-LINK

HDMI IN

DIGITAL

AUDIO OUT

ANT (75

)

ANT1 (CABLE)

ANT2

CableCARD™

COLOR STREAM HD-1

COLOR STREAM HD-2

VAR

AUDIO

TheaterNet

OUT 2

S-VIDEO

IEEE1394

EJECT

L/ MONO

AUDIO

VIDEO

L/ MONO

AUDIO

VIDEO

L/ MONO

AUDIO

VIDEO

AUDIO

{

HM94(E)009-11(2A-Cnct) 8/30/04, 1:39 PM10

Overview of cable types

Component video cables (red/green/blue)

Coaxial (F-type) cable

Standard A/V cables (red/white/yellow)

S-video cable

HDMI cable

Dual-wand IR blaster/G-LINK cable (2 included)

Note: Two dual-wand IR blaster/G-LINK cables are included with your TV. All other required cables, if not provided with your other devices, can be purchased at many electronics accessory suppliers.

●

Coaxial (F-type) cable is used for connecting your antenna, cable TV service, and/or cable converter box to the ANT-1 and/or ANT-2 RF inputs on your TV.

●

Standard A/V cables (composite video) usually come in sets of three, and are for use with video devices with standard audio and standard (composite) video output. These cables (and the related inputs on your TV) are typically color-coded according to use: yellow for video, red for stereo right audio, and white for stereo left (or mono) audio.

●

S-video cable is for use with video devices with S-video output. Separate audio cables are required for a complete connection.

Note: An S-video cable provides better picture performance than a composite video cable. If you connect an S-video cable, be sure to disconnect the standard (composite) video cable or the picture performance will be unacceptable.

●

Component video cables come in sets of three and are for use with video devices with component video output. (ColorStream

is Toshiba’s brand of component video.) These cables are typically color-coded red, green, and blue. Separate audio cables are required for a complete connection.

Note: Component video cables provide better picture performance than a standard (composite) video or S-video cable.

●

HDMI cable is for use with devices with HDMI (high-definition multimedia interface) output. HDMI cable delivers digital audio and video in its native format. This cable carries both video and audio information; therefore, no separate audio cables are required for a complete HDMI device connection. See page 19 for further details.

Note: HDMI cable provides better picture performance than a standard (composite) video or S-video cable.

●

IEEE-1394 cable is for use with video devices with compressed digital video output that meets CEA specifications for IEEE-1394. This cable carries both video and audio information; therefore, no separate audio cables are required for a complete connection. See pages 22–24.

Note:

• The transmission capability of IEEE-1394 cable used with this TV must be S400 (400 Mbps maximum).

• IEEE-1394 cable provides better picture performance than a standard (composite) video or S-video cable.

●

Dual-wand IR blaster/G-LINK™ cable is for use with video devices with IR (infrared) remote control. Two of these cables are included with your TV. One is for connection to the G-LINK jack (page 25) to enable TV Guide On Screen

™

recording features (Chapters 5 and 7). The other can be used with the TV’s IR pass-through feature (page 21) and TheaterNet on-screen device control feature (page 44).

Note: The two IR blaster/G-LINK cables included with your TV have specific characteristics that allow them to work properly with this TV’s IR OUT and G-LINK ports. Never use other aftermarket IR blaster or G-LINK cables with this TV. Other cables may not function properly and can cause damage. THIS TYPE OF DAMAGE IS NOT COVERED BY YOUR TOSHIBA WARRANTY.

●

Optical audio cable is for connecting receivers with Dolby® Digital or PCM (pulse-code modulation) optical audio input to the TV’s DIGITAL AUDIO OUT jack. See page 20.

IEEE-1394 cable (4-pin)

Optical audio cable

Chapter 2: Connecting your TV

Note: Although your TV includes both HDMI

and IEEE-1394 connections, it may not operate with another device you have that includes such a connection. For example, the IEEE-1394 ports are not intended to operate with current model Mini DV camcorders, and the HDMI input is not intended for connection to a computer. Copyright protection requirements may also prohibit or limit connectivity. See page 19 for details about the HDMI input. See pages 22–24 for details about the IEEE-1394 ports.

__________ Dolby is a registered trademark of Dolby Laboratories.

NOTE: NEVER CONNECT THIS TV TO A PERSONAL COMPUTER (PC).

THIS TV IS NOT INTENDED FOR USE WITH A PC.

HM94(E)009-11(2A-Cnct) 8/30/04, 1:39 PM11

Chapter 2: Connecting your TV

About the connection illustrations

You can connect different types and brands of devices to your TV in several different configurations. The connection illustrations in this manual are representative of typical device connections only. The input/output jacks on your devices may differ from those illustrated herein. For details on connecting and using your specific devices, refer to each device’s owner’s manual.

Connecting a digital CableCARD™

This digital television is capable of receiving analog basic, digital basic, and digital premium cable television programming by direct connection to a cable system providing such programming.

A security card (such as a digital CableCARD

™

), provided by your cable operator, is required to view encrypted digital programming.

Certain advanced and interactive digital cable services (such as video-on-demand, a cable operator’s enhanced program guide, and data-enhanced television services) will not work with the use of a CableCARD and may require the use of a separate set-top box from your cable operator.

For more information, call your local cable operator.

You will need:

 one digital CableCARD (contact your cable operator)  digital cable subscription service (contact your cable

operator)



To view encrypted digital channels:

1. Connect your digital Cable TV cable to ANT-1.

2. With the front of the CableCARD

™

facing right, insert it into the CableCARD slot on the back of the TV (see illustration below left).

3. After the CableCARD is inserted, a CableCARD option appears in the APPLICATIONS menu, with informational screens provided by your digital CableCARD service. See page 50 for additional information.

From digital Cable service (connect to ANT 1 only)

________

CableCARD is a trademark of Cable Television Laboratories, Inc.

OUT

AUDIO

S-VIDEO

VIDEO 1 VIDEO 2

OUT 1

G-LINK

HDMI IN

DIGITAL

AUDIO OUT

ANT (75

)

ANT1

(CABLE)

ANT2

CableCARD™

COLOR STREAM

HD-1

COLOR

STREAM

HD-2

VAR

AUDIO

TheaterNet

OUT 2

S-VIDEO

IEEE1394

EJECT

L/ MONO

AUDIO

VIDEO

L/ MONO

AUDIO

VIDEO

MONO

AUDIO

VIDEO

AUDIO

TheaterNet

CableCard Connected -- Acquiring channel information.

CableCard services will only operate with cable signal connected to Antenna 1.

NOTE:

• Never remove the CableCARD carelessly. Be sure to use the EJECT button when removing the CableCARD.

• Never insert any object or card (including, without limitation, a PCMCIA card) other than a CableCARD into the CableCARD slot.

• Always make sure the CableCARD is facing the correct direction.

• Connect the cable for your digital cable TV service to ANT-1 only.

•A digital cable subscription is required to use a CableCARD. Contact your Cable company for information.

• If the TV locks up with the CableCARD inserted, press the RESET button on the TV front or unplug the TV, plug it in again, and press POWER.

•When using a CableCARD, channel programming (page 41) is unnecessary because the CableCARD automatically loads the cable channel list into the TV’s channel memory.

•The CableCARD will take several seconds to “pair” with the TV. CableCARD information and channel listings will not be available until this “pairing” process is completed.

TV back panel

INSERT THIS EN D

Digital

™

HM94(E)012-25(2B-Cnct) 8/31/04, 12:51 PM12

Chapter 2: Connecting your TV

TheaterNet

OUT

AUDIO

S-VIDEO

VIDEO 1 VIDEO 2

OUT 1

G-LINK

HDMI IN

DIGITAL

AUDIO OUT

ANT (75

)

ANT1

(CABLE)

ANT2

CableCARD™

COLOR

STREAM

HD-1

COLOR

STREAM

HD-2

VAR

AUDIO

TheaterNet

OUT 2

S-VIDEO

IEEE1394

EJECT

L/ MONO

AUDIO

VIDEO

L/ MONO

AUDIO

VIDEO

L/ MONO

AUDIO

VIDEO

AUDIO

IN from ANT

VIDEO AUDIO

OUT to TV

CH 3

CH 4

OUT

TheaterNet

You will need:

 one coaxial cable  one set of standard A/V cables

• For better picture performance, if your VCR has S-video, use an S-video cable (plus the audio cables) instead of the standard video cable. However, do not connect both types of video cables to VIDEO 1 (or VIDEO 2) at the same time or the picture performance will be unacceptable.

• If you have a mono VCR, connect L/MONO on the TV to your VCR’s audio out jack using the white audio cable only.



To view the antenna or Cable signal:

Turn OFF the VCR. Select the ANT 1 video input source.*



To view the VCR:

Turn ON the VCR. Select the VIDEO 1 video input source on the TV.*

or…Turn ON the VCR. Select the ANT 1 video input source.*

Tune the TV to channel 3 or 4 (whichever channel is vacant in your area).

Connecting a VCR and antenna or Cable TV (no Cable box)

From Cable TV or antenna

Stereo VCR

The unauthorized recording, use, distribution, or revision of television programs, videotapes, DVDs, and other materials is prohibited under the Copyright Laws of the United States and other countries, and may subject you to civil and criminal liability.



To use the TV Guide On Screen recording features:

1. Connect the G-LINK cable according to the instructions on page 25.

2. Make sure the VCR is connected to the A/V OUT jacks on the TV (see illustration).

3. Set the VCR to the appropriate line input (refer to your VCR owner’s manual for details), and then turn OFF the VCR.

4. See Chapter 5 for details on setting up the TV Guide On Screen system.

5. See Chapter 7 for details on using the TV Guide On Screen system.

Connecting a camcorder

VIDEO

AUDIO

OUT

You will need:

 one set of standard A/V cables

• For better picture performance, if your camcorder has S-video, use an S-video cable (plus the audio cables) instead of the standard video cable. Do not connect both an S-video cable and a standard video cable to VIDEO 3 at the same time or the picture performance will be unacceptable.



To view the camcorder video:

Select the VIDEO 3 video input source.*

VIDEO 3 inputs on TV right side panel

Camcorder

_____________

* To select the video input source, press INPUT on the remote control (see page 67).

To program the TV remote control to operate other devices, see Chapter 3.

Note: The VIDEO/AUDIO OUT jacks output the signals from the ANT 1, ANT 2, VIDEO 1, VIDEO 2, or VIDEO 3 jacks when the appropriate input mode is selected.

HM94(E)012-25(2B-Cnct) 8/31/04, 12:51 PM13

Chapter 2: Connecting your TV

TheaterNet

OUT

AUDIO

S-VIDEO

VIDEO 1 VIDEO 2

OUT 1

G-LINK

HDMI IN

DIGITAL

AUDIO OUT

ANT (75

)

ANT1

(CABLE)

ANT2

CableCARD™

COLOR

STREAM

HD-1

COLOR

STREAM

HD-2

VAR

AUDIO

TheaterNet

OUT 2

S-VIDEO

IEEE1394

EJECT

MONO

AUDIO

VIDEO

MONO

AUDIO

VIDEO

L/ MONO

AUDIO

VIDEO

AUDIO

TheaterNet

OUT

IN from ANT

VIDEO AUDIO

OUT to TV

CH 3

CH 4

OUT

CH 3 CH 4

Cable box Cable splitter

You will need:

 one Cable signal splitter  five coaxial cables  two sets of standard A/V cables

• For better picture performance from your VCR: If your VCR has S-video, connect an S-video cable (plus the audio cables) instead of the standard video cable. Do not connect an S-video cable and a standard video cable to VIDEO 1 (or VIDEO 2) at the same time or the picture performance will be unacceptable.

• If you have a mono VCR, connect L/MONO on the TV to your VCR’s audio out jack using the white audio cable only.

• For better picture performance from your Cable box: If your Cable box has component video, you can connect component video cables (plus the audio cables) instead of the standard video cable from the Cable box to the ColorStream HD-1 inputs on the TV. You would then select ColorStream HD-1 as the video input source.*

•When you use a Cable box, you may not be able to use the remote control to program or access certain features on the TV.



To view basic Cable channels and use the TV’s features:

Select the ANT 2 video input source.* Use the TV front panel controls or remote control to change channels and access the TV’s features.



To view basic and premium Cable channels:

Turn OFF the VCR. Select the ANT 1 video input source.* Tune the TV to channel 3 or 4 (whichever channel is vacant in your area). Use the Cable box controls to change channels.

or…Turn ON the VCR. Tune the VCR to channel 3 or 4

(whichever channel is vacant in your area). Select the VIDEO 1 video input source.* Use the Cable box controls to change channels.



To view the VCR:

Turn ON the VCR. Select the VIDEO 1 video input source.*

Note: This will provide better picture performance if you connected an S-video cable as mentioned in the first bulleted item on this page.

or…Turn ON the VCR. Select the ANT 1 video input source.*

Tune the TV to channel 3 or 4 (whichever channel is vacant in your area).

_____________

* To select the video input source, press INPUT on the remote control

(see page 67). To program the TV remote control to operate other devices, see Chapter 3.

From Cable TV

Connecting a VCR and Cable box

Stereo VCR



To enable the TV Guide On Screen system to work with your cable box and to use the TV Guide On Screen recording features:

1. Connect the G-LINK cable according to the instructions on page 25.

2. Make sure the VCR is connected to the A/V OUT jacks on the TV (see illustration).

3. Set the VCR to the appropriate line input (refer to your VCR owner’s manual for details), and then turn OFF the VCR.

4. See Chapter 5 for details on setting up the TV Guide On Screen system.

5. See Chapter 7 for details on using the TV Guide On Screen system.

Note: The VIDEO/AUDIO OUT jacks output the signals from the ANT 1, ANT 2, VIDEO 1, VIDEO 2, or VIDEO 3 jacks when the appropriate input mode is selected.

HM94(E)012-25(2B-Cnct) 8/31/04, 12:52 PM14

Chapter 2: Connecting your TV

TheaterNet

OUT

AUDIO

S-VIDEO

VIDEO 1 VIDEO 2

OUT 1

G-LINK

HDMI IN

DIGITAL

AUDIO OUT

ANT (75

)

ANT1

(CABLE)

ANT2

CableCARD™

COLOR

STREAM

HD-1

COLOR STREAM

HD-2

VAR

AUDIO

TheaterNet

OUT 2

S-VIDEO

IEEE1394

EJECT

L/ MONO

AUDIO

VIDEO

L/ MONO

AUDIO

VIDEO

L/ MONO

AUDIO

VIDEO

AUDIO

TheaterNet

IN from ANT

CH 3 CH 4

VIDEO AUDIO

OUT to TV

OUT

S-VIDEO

OUT

VIDEO

OUT

AUDIO

OUT

COMPONENT VIDEO

LRL

Satellite

PB PR

Connecting a VCR and satellite receiver

You will need:

 three coaxial cables  one set of component video cables (if your

satellite receiver does not have component video, connect the standard A/V cables only)

 three sets of standard A/V cables

• For better picture performance, if your satellite receiver and VCR have S-video, connect S-video cables (plus the audio cables) instead of the standard video cables. Do not connect both types of video cable to VIDEO 1 (or VIDEO 2) at the same time or the picture performance will be unacceptable.

• If you have a mono VCR, connect L/MONO on the TV (VIDEO 1) to your VCR’s AUDIO OUT jack using the white audio cable only.



To view satellite programs using the component video connections:

Select the ColorStream HD-1 video input source on the TV.*



To view satellite programs using the standard

From

antenna

From

satellite

dish

Satellite receiver

Stereo VCR

video connections or to record satellite programs:

Turn on all three devices. Set the VCR to the appropriate line input (refer to your VCR owner’s manual for details). Select the VIDEO 2 video input source on the TV.*



To view the VCR or view and record antenna channels:

Turn ON the VCR. Select the ANT-1 video input source on the TV.* Tune the TV to channel 3 or 4 (whichever channel is vacant in your area).

or... Turn ON the VCR. Tune the VCR to the channel you

want to watch. Select the VIDEO 1 video input source on the TV.*

_____________

* To select the video input source, press INPUT on the remote control

(see page 67). To program the TV remote control to operate other devices, see Chapter 3.

Note: The TV Guide On Screen® system does not receive program listings from or for any satellite service.



To use the TV Guide On Screen recording features:

1. Connect the G-LINK cable according to the instructions on page 25.

2. Make sure the VCR is connected to the A/V OUT jacks on the TV (see illustration).

3. Set the VCR to the appropriate line input (refer to your VCR owner’s manual for details), and then turn OFF the VCR.

4. See Chapter 5 for details on setting up the TV Guide On Screen system.

5. See Chapter 7 for details on using the TV Guide On Screen system.

Note: The VIDEO/AUDIO OUT jacks output the signals from the ANT 1, ANT 2, VIDEO 1, VIDEO 2, or VIDEO 3 jacks when the appropriate input mode is selected.

HM94(E)012-25(2B-Cnct) 8/31/04, 12:52 PM15

Chapter 2: Connecting your TV

TheaterNet

OUT

AUDIO

S-VIDEO

VIDEO 1 VIDEO 2

OUT 1

G-LINK

HDMI IN

DIGITAL

AUDIO OUT

ANT (75

)

ANT1

(CABLE)

ANT2

CableCARD™

COLOR STREAM

HD-1

COLOR

STREAM

HD-2

VAR

AUDIO

TheaterNet

OUT 2

S-VIDEO

IEEE1394

EJECT

MONO

AUDIO

VIDEO

L/ MONO

AUDIO

VIDEO

L/ MONO

AUDIO

VIDEO

AUDIO

TheaterNet

AUDIO

OUT

VIDEO

OUT

S-VIDEO

OUT

IN from ANT

VIDEO AUDIO

OUT to TV

CH 3

CH 4

OUT

CH 3 CH 4

Cable box Cable splitter

Connecting a DVD player with S-video, a VCR, and a Cable box

You will need:

 five coaxial cables  two sets of standard A/V cables

Note: If you have a mono VCR, connect L/MONO on the TV (VIDEO 1) to your VCR’s audio out jack using the white audio cable only.

 one S-video cable  one pair of standard audio cables

Note:

• If your DVD player does not have S-video, use a standard video cable instead. Do not connect an S-video cable and a standard video cable to VIDEO 1 (or VIDEO 2) at the same time or the picture performance will be unacceptable.

• If your DVD player has component video, see page 17.

• Do not connect the DVD player and VCR to the same set of A/V inputs on the TV. (See the illustration, which shows the VCR connected to VIDEO 1 on the TV, and the DVD player connected to VIDEO 2.)



To view basic channels and access the TV’s features:

Select the ANT 2 video input source.* Use the TV controls to change channels and access the TV’s features.



To view premium Cable channels:

Turn OFF the VCR. Select the ANT 1 video input source.* Tune the TV to channel 3 or 4 (whichever channel is vacant in your area). Use the Cable box controls to change channels.

or…Turn ON the VCR. Tune the VCR to channel 3 or 4

(whichever channel is vacant in your area). Select the VIDEO 1 video input source.* Use the Cable box controls to change channels.

Note: When you use a Cable box, you may not be able to use the remote control to program or access certain features on the TV.



To view the DVD player:

Turn ON the DVD player. Select the VIDEO 2 video input source.*



To view VCR 1:

Turn ON the VCR. Select the VIDEO 1 video input source on the TV.*

or…Turn ON the VCR. Select the ANT 1 video input

source.* Tune the TV to channel 3 or 4 (whichever channel is vacant in your area).

_____________

* To select the video input source, press INPUT on the remote control

(see page 67). To program the TV remote control to operate other devices, see Chapter 3.

DVD player with S-video

Stereo VCR

From antenna or Cable TV

Note: The VIDEO/AUDIO OUT jacks output the signals from the ANT 1, ANT 2, VIDEO 1, VIDEO 2, or VIDEO 3 jacks when the appropriate input mode is selected.



To enable the TV Guide On Screen system to work with your cable box and to use the TV Guide On Screen recording features:

1. Connect the G-LINK cable according to the instructions on page 25.

2. Make sure the VCR is connected to the A/V OUT jacks on the TV (see illustration).

3. Set the VCR to the appropriate line input (refer to your VCR owner’s manual for details), and then turn OFF the VCR.

4. See Chapter 5 for details on setting up the TV Guide On Screen system.

5. See Chapter 7 for details on using the TV Guide On Screen system.

HM94(E)012-25(2B-Cnct) 8/31/04, 12:52 PM16

Chapter 2: Connecting your TV

TheaterNet

OUT

AUDIO

S-VIDEO

VIDEO 1 VIDEO 2

OUT 1

G-LINK

HDMI IN

DIGITAL

AUDIO OUT

ANT (75

)

ANT1

(CABLE)

ANT2

CableCARD™

COLOR

STREAM

HD-1

COLOR

STREAM

HD-2

VAR

AUDIO

TheaterNet

OUT 2

S-VIDEO

IEEE1394

EJECT

L/ MONO

AUDIO

VIDEO

MONO

AUDIO

VIDEO

L/ MONO

AUDIO

VIDEO

AUDIO

TheaterNet

S-VIDEO

OUT

VIDEO

OUT

AUDIO

OUT

COMPONENT VIDEO

PBP

IN from ANT

VIDEO AUDIO

OUT to TV

CH 3

CH 4

OUT

Connecting a DVD player with ColorStream® (component video) and a VCR

From antenna or Cable

Your TV has ColorStream® (component video) inputs. Connecting a DVD player with component video output (such as a Toshiba DVD player with ColorStream

) can greatly

enhance picture quality.

You will need:

 two coaxial cables  two sets of standard A/V cables

• For better picture performance, if your VCR has S-video, use an S-video cable (plus the audio cables) instead of the standard video cable. However, do not connect both types of video cable to VIDEO 1 (or VIDEO 2) at the same time or the picture performance will be unacceptable.

• If you have a mono VCR, connect L/MONO on the TV (VIDEO 1) to your VCR’s audio out jack using the white audio cable only.

 one pair of standard audio cables  one set of component video cables

•You can connect the component video cables (plus audio cables) from the DVD player to either set of ColorStream jacks on the TV (HD-1 or HD-2). The ColorStream HD-1 and HD-2 jacks can be used with Progressive (480p, 720p) and Interlaced (480i, 1080i) scan systems. A 1080i signal will provide the best picture performance.

• If your DVD player does not have component video, see page 16. If your DVD player has HDMI video, see page 19.



To view antenna or Cable channels:

Turn OFF the VCR. Select the ANT 1 video input source on the TV.*



To view the DVD player:

Turn ON the DVD player. Select the ColorStream HD-1 video input source on the TV.*



To view the VCR:

Turn ON the VCR. Select the VIDEO 1 video input source on the TV.*

or…Turn ON the VCR. Select the ANT 1 video input source.*

Tune the TV to channel 3 or 4 (whichever channel is vacant in your area).



To record a TV program while watching a DVD:

Turn ON the VCR. Tune the VCR to the channel to record. Select the ColorStream HD-1 video input source on the TV* to view the DVD.

_____________

* To select the video input source, press INPUT on the remote control

(see page 67). To program the TV remote control to operate other devices, see Chapter 3.

DVD player with component video

Stereo VCR



To use the TV Guide On Screen recording features:

1. Connect the G-LINK cable according to the instructions on page 25.

2. Make sure the VCR is connected to the A/V OUT jacks on the TV (see illustration).

3. Set the VCR to the appropriate line input (refer to your VCR owner’s manual for details), and then turn OFF the VCR.

4. See Chapter 5 for details on setting up the TV Guide On Screen system.

5. See Chapter 7 for details on using the TV Guide On Screen system.

Note: The VIDEO/AUDIO OUT jacks output the signals from the ANT 1, ANT 2, VIDEO 1, VIDEO 2, or VIDEO 3 jacks when the appropriate input mode is selected.

HM94(E)012-25(2B-Cnct) 8/31/04, 12:52 PM17

Chapter 2: Connecting your TV

TheaterNet

OUT

AUDIO

S-VIDEO

VIDEO 1 VIDEO 2

OUT 1

G-LINK

HDMI IN

DIGITAL

AUDIO OUT

ANT (75

)

ANT1

(CABLE)

ANT2

CableCARD™

COLOR

STREAM

HD-1

COLOR

STREAM

HD-2

VAR

AUDIO

TheaterNet

OUT 2

S-VIDEO

IEEE1394

EJECT

L/ MONO

AUDIO

VIDEO

L/ MONO

AUDIO

VIDEO

L/ MONO

AUDIO

VIDEO

AUDIO

TheaterNet

IN from ANT

VIDEO AUDIO

OUT to TV

CH 3

CH 4

OUT

IN from ANT

VIDEO AUDIO

OUT to TV

CH 3

CH 4

OUT

Connecting two VCRs

You will need:

 two coaxial cables  two sets of standard A/V cables

• For better picture performance, if VCR 1 has S-video, use an S-video cable (plus the audio cables) instead of the standard video cable. However, do not connect both types of video cable to VIDEO 1 (or VIDEO 2) at the same time or the picture performance will be unacceptable.

• If VCR 1 has mono audio, connect L/MONO on the TV (VIDEO 1) to the audio out jack on VCR 1 using the white audio cable only.

• Do not connect the same VCR to the output and input jacks on the TV at the same time.



To view the antenna or Cable signal:

Turn OFF VCR 1. Select the ANT-1 video input source.*



To view VCR 1:

Turn ON VCR 1. Select the VIDEO 1 video input source.*



To dub or edit from VCR 1 to VCR 2:

Turn ON both VCRs. Set VCR 2 to the appropriate line input (refer to your VCR owner’s manual for details).

Select the VIDEO 1 video input source.*

Note:

• If you have a Cable box, connect the Cable box and splitter to VCR1 as shown on page 14.

•The VIDEO OUT signal incorporates Macrovision

The VIDEO OUT jack does not output the POP picture.

When the POP window is open, the AUDIO OUT jacks output the sound of the active window (main or POP). For additional information, see “Notes about recording” on page 73.

VCR1 (plays)

From

antenna

or Cable

VCR2 (records)

**This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision and is intended for home and other limited pay-per-view uses only, unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited. Macrovision is a registered trademark of Macrovision Corporation.



To use the TV Guide On Screen recording features:

Note: If you connect your devices according to the illustration above, you will record from the TV Guide On Screen system to the VCR labeled “VCR2.”

1. Connect the G-LINK cable according to the instructions on page 25.

2. Make sure the VCR2 is connected to the A/V OUT jacks on the TV (see illustration).

3. Set the VCR to the appropriate line input (refer to your VCR owner’s manual for details), and then turn OFF the VCR.

4. See Chapter 5 for details on setting up the TV Guide On Screen system.

5. See Chapter 7 for details on using the TV Guide On Screen system.

Note: The VIDEO/AUDIO OUT jacks output the signals from the ANT 1, ANT 2, VIDEO 1, VIDEO 2, or VIDEO 3 jacks when the appropriate input mode is selected.

_____________

* To select the video input source, press INPUT on the remote control

(see page 67). To program the TV remote control to operate other devices, see Chapter 3.

HM94(E)012-25(2B-Cnct) 8/31/04, 12:52 PM18

Chapter 2: Connecting your TV

TheaterNet

OUT

AUDIO

S-VIDEO

VIDEO 1 VIDEO 2

OUT 1

G-LINK

HDMI IN

DIGITAL

AUDIO OUT

ANT (75

)

ANT1

(CABLE)

ANT2

CableCARD™

COLOR

STREAM

HD-1

COLOR

STREAM

HD-2

VAR

AUDIO

TheaterNet

OUT 2

S-VIDEO

IEEE1394

EJECT

L/ MONO

AUDIO

VIDEO

L/ MONO

AUDIO

VIDEO

L/ MONO

AUDIO

VIDEO

AUDIO

TheaterNet

OUT

HDMI OUT

VIDEO AUDIO

The HDMI

[1]

input on your TV receives digital audio and uncompressed digital video from an HDMI device or uncompressed digital video from a DVI

[2]

device.

This input is designed to accept HDCP

[3]

program material in

digital form from EIA/CEA-861/861B–compliant

[4]

consumer electronic devices (such as a set-top box or DVD player with HDMI or DVI output).

The HDMI input is designed for best performance with 720p and 1080i high-definition video signals, but will also accept and display 480i and 480p signals.

Connecting an HDMI™ or a DVI device to the HDMI input

HDMI device

TheaterNet

OUT

AUDIO

S-VIDEO

VIDEO 1 VIDEO 2

OUT 1

G-LINK

HDMI IN

DIGITAL

AUDIO OUT

ANT (75

)

ANT1

(CABLE)

ANT2

CableCARD™

COLOR STREAM

HD-1

COLOR

STREAM

HD-2

VAR

AUDIO

TheaterNet

OUT 2

S-VIDEO

IEEE1394

EJECT

L/ MONO

AUDIO

VIDEO

L/ MONO

AUDIO

VIDEO

MONO

AUDIO

VIDEO

AUDIO

TheaterNet

VIDEO AUDIO

OUT

DVI/HDCP

OUT

___________

[1]

HDMI = High-Definition Multimedia Interface.

[2]

DVI = Digital Video Interface.

[3]

HDCP = High-bandwidth Digital Content Protection.

[4]

EIA/CEA-861/861B compliance covers the transmission of uncompressed digital video with high-bandwidth digital content protection, which is being standardized for reception of high-definition video signals. Because this is an evolving technology, it is possible that some devices may not operate properly with the TV.

NOTE: To ensure that the HDMI or DVI device is reset properly, it is recommended that you follow these procedures:

•When turning on your electronic components, turn on the TV first, and then the HDMI or DVI device.

•When turning off your electronic components, turn off the HDMI or DVI device first, and then the TV.

To connect a DVI device, you will need:

• one HDMI-to-DVI adapter cable (HDMI type A connector)

For proper operation, the length of an HDMI-to-DVI adapter cable should not exceed 9.8 ft (3m). The recommended length is 6.6 ft (2m).

• one pair of standard analog audio cables

An HDMI-to-DVI adapter cable transfers video only. Separate analog audio cables are required (see illustration below).

See “Setting the HDMI audio mode” on page 49.

___________

HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing, LLC.

To connect an HDMI device, you will need:

• one HDMI cable (type A connector)

For proper operation, it is recommended that you use as short an HDMI cable as possible. You should not encounter difficulty if you use an HDMI cable shorter than 16.4 ft (5m).

HDMI cable transfers both video and audio. Separate analog audio cables are not required (see illustration below). Some CDVs (video CDs) may not output digital audio signals. In that case, you may hear sound by connecting analog audio cables. However, if you connect analog audio cables with this connection, the HDMI terminal on the TV will not receive the HDMI digital audio signal and you will hear analog audio only.

See “Setting the HDMI audio mode” on page 49.

NOTE: NEVER CONNECT THIS TV TO A PERSONAL COMPUTER (PC).

THIS TV IS NOT INTENDED FOR USE WITH A PC.

DVI device

HM94(E)012-25(2B-Cnct) 8/31/04, 12:52 PM19

Chapter 2: Connecting your TV

Connecting a digital audio system

This connection allows you to use external speakers with an external audio amplifier to adjust the sound level.

You will need:

 one pair of standard audio cables

To control the audio:

Turn on the TV and the stereo amplifier. Turn off the TV’s built-in speakers (see “Turning off the built-in

speakers” on page 81).

Note: To hear sound when using an external audio amplifier, the volume of both the TV and the amplifier must be set to a reasonable listening level.

TheaterNet

OUT

AUDIO

S-VIDEO

VIDEO 1 VIDEO 2

OUT 1

G-LINK

HDMI IN

DIGITAL

AUDIO OUT

ANT (75

)

ANT1

(CABLE)

ANT2

CableCARD™

COLOR

STREAM

HD-1

COLOR

STREAM

HD-2

VAR

AUDIO

TheaterNet

OUT 2

S-VIDEO

IEEE1394

EJECT

L/ MONO

AUDIO

VIDEO

L/ MONO

AUDIO

VIDEO

L/ MONO

AUDIO

VIDEO

AUDIO

TheaterNet

LINE IN LR

Analog audio amplifier

Connecting an analog audio system

The TV’s DIGITAL AUDIO OUT jack outputs a

or 2-channel down-mixed PCM (pulse-code modulation) signal for use with an external Dolby Digital decoder or other external audio system with optical audio input.

You will need:

 one optical audio cable

To control the audio:

Turn on the TV and the digital audio device. Press MENU on the TV’s remote control and open the AUDIO

menu. Highlight AUDIO SETUP and press ENTER. In the OPTICAL OUTPUT FORMAT field, select either

DOLBY DIGITAL or PCM, depending on your device (see “Selecting the optical audio output format” on page 81).

Turn off the TV’s built-in speakers in the same AUDIO SETUP menu (above). Also see “Turning off the built-in speakers” on page 81.

TheaterNet

OUT

AUDIO

S-VIDEO

VIDEO 1 VIDEO 2

OUT 1

G-LINK

HDMI IN

DIGITAL

AUDIO OUT

ANT (75

)

ANT1

(CABLE)

ANT2

CableCARD™

COLOR

STREAM

HD-1

COLOR

STREAM

HD-2

VAR

AUDIO

TheaterNet

OUT 2

S-VIDEO

IEEE1394

EJECT

L/ MONO

AUDIO

VIDEO

L/ MONO

AUDIO

VIDEO

L/ MONO

AUDIO

VIDEO

AUDIO

TheaterNet

LINE IN

Optical

Audio IN

Dolby Digital decoder or

other digital audio system

Note:

• Some audio systems may not be compatible with Dolby Digital bitstream signals. Older audio systems that are not compatible with standard optical out signals may not work properly, creating a high noise level that may damage speakers or headphones. THIS DAMAGE IS NOT

COVERED BY YOUR WARRANTY.

•The DIGITAL AUDIO OUT jack may not output some digital audio sources because of copy restrictions.

HM94(E)012-25(2B-Cnct) 8/31/04, 12:53 PM20

Chapter 2: Connecting your TV

For additional control options for your home theater system, set up the TheaterNet on-screen device control feature. You can use this feature to control many IR remote-controlled devices and IEEE-1394 devices using the on-screen control icons.

You can use the TV’s IR OUT jack (infrared pass-through) to remotely operate (through the TV) many infrared remote-controlled devices (such as a Toshiba infrared remote-controlled VCR or DVD player) enclosed within an entertainment center or similar cabinet. Without the IR OUT connection, the device typically would need to be visible to operate it remotely.

You will need:

 one dual-wand IR blaster cable (included with your TV)  other audio/video cables as required to connect the device(s)

to the TV (see pages 13–20)

To connect the IR blaster cable:

1. Locate the infrared sensor on the front of your device. This sensor is marked on some devices.*

2. Align one of the IR blaster cable’s wands about 1 inch away from the infrared sensor on the front of the device and attach it using double-sided mounting tape. If you have a second device, attach the second wand in a similar manner. (See illustration at right.)

Note: If you do not have a second device, coil the second wand with a rubber band and leave it behind the TV.

3. Plug the IR blaster cable’s plug into one of the TV’s TheaterNet OUT jacks.

Controlling infrared remote-controlled devices through the TV (IR pass-through)

1 0 0

E N

A B L E

/S A T

P O

W E R

+ 1 0

D VD

A U

D IO 1

U DIO

A C T I

O N

O D

P I C

S I Z E

M E N

I G H T

S L

E E P

E N T

E R

A V

C H

T V /

C R

V O L

X I T

I S

C H R

T N

D V D

R T N

V D

C L E A R

S L O W

P A U S

E / S T E

A M /F

S K

IP /S E

A R C

P L A Y

R E W

F F

T O P

POP

DIRECT C

F R E E

Z E

S P

LIT

CH SCAN

O U RC

S W A

P O P

C H

R E C

IN P U

R E C

A L L

M U

T E

F A V

MENUVOLUMECHANNELEXITTV/VIDEO POWER

To control the device(s):

Point the TV remote control (programmed to operate the device; see Chapter 3) or the device’s remote control at the front of the TV and press the button for the desired function. The signal passes from the remote control through the TV to the device via the IR blaster cable.

Note:

• If you use the device’s remote control to operate the device, you also will need to use the TV’s remote control to operate the TV.

• For additional control options, see “TheaterNet on-screen device control” at right.

TheaterNet

OUT

AUDIO

S-VIDEO

VIDEO 1 VIDEO 2

OUT 1

G-LINK

HDMI IN

DIGITAL

AUDIO OUT

ANT (75

)

ANT1

(CABLE)

ANT2

CableCARD™

COLOR

STREAM

HD-1

COLOR

STREAM

HD-2

VAR

AUDIO

TheaterNet

OUT 2

S-VIDEO

IEEE1394

EJECT

L/ MONO

AUDIO

VIDEO

MONO

AUDIO

VIDEO

L/ MONO

AUDIO

VIDEO

AUDIO

Back of TV

Front of IR-controlled audio device (for example)

Front of IR-controlled DVD player (for example)

IR blaster cable wand (approx. 1 inch from device)

Infrared

sensor

TheaterNet

TheaterNet™ on-screen device control

See pages 44–48 for details on setting up and using TheaterNet.

See pages 22–24 for details on connecting IEEE-1394 devices.

Note: The TheaterNet icon controls are the only device functions available when the icons are on-screen. To access other device functions, close the TheaterNet icon window.

If you cannot locate the device’s infrared sensor:

1. Turn OFF the device.

2. Starting at the lower left corner of the device, place the end of the device’s remote control (with the infrared emitter) so it touches the front of the device and press POWER. (Do not use the TV’s remote control for this step.)

3. If the device turns on, the place the remote control touched the device is the location of the sensor.

4. If the device does not turn on, move the remote control slightly to the right and press POWER again.

5. Repeat step 4 until you locate the device’s infrared sensor.

IR Home-TheaterLink

1 0 0 /

E N

C A

B L E

/ S A T

VCR

P O W E

1 0

DVD

AUDIO1

AUDIO2

AC T ION

O D E

P IC

S IZ E

M E N

L I G H T

L E E P

E N

T E

F A V

C H

T V

/ V C

V O

L E X

I T

D I

S C

C H RTN

D V D R

T N

V D C

L E A

S L

O W /

D I R

PA USE

/ST EP

AM/F

S K

IP /S

E A

S TO

P O P

D I R E C

T C H

F R

E E Z E

SPLIT

CH SCAN

S O U

R C E

S W

A P

P O

P C

INPU

R E

C A L L

M U

I N

A V

MENUVOLUMECHANNELEXITTV/VIDEO POWER

DVD

HM94(E)012-25(2B-Cnct) 8/31/04, 12:53 PM21

Chapter 2: Connecting your TV

OUT

AUDIO

S-VIDEO

VIDEO 1 VIDEO 2

OUT 1

G-LINK

HDMI IN

DIGITAL

AUDIO OUT

ANT (75

)

ANT1

(CABLE)

ANT2

CableCARD™

COLOR

STREAM

HD-1

COLOR

STREAM

HD-2

VAR

AUDIO

TheaterNet

OUT 2

S-VIDEO

IEEE1394

EJECT

MONO

AUDIO

VIDEO

L/ MONO

AUDIO

VIDEO

L/ MONO

AUDIO

VIDEO

AUDIO

TheaterNet

Connecting IEEE-1394 video devices

You can use the two bi-directional IEEE-1394 ports on the back of your TV to connect digital video devices that meet CEA specifications for IEEE-1394.

Because these ports are bi-directional, they can be used for both playback and recording.

• Because IEEE-1394 is an evolving technology, it is possible that some or all of the connectivity features of a device you connect to the TV through the IEEE-1394 ports may not operate. You should confirm that the devices you desire to use with the IEEE-1394 ports will operate with those ports.

•This TV does not support all possible IEEE-1394 signal types. For information on signals supported by the IEEE-1394 ports, see “Supported signals” at right.

•IEEE-1394 cable carries both audio and video information; no separate audio cables are required for a complete connection.

You will need:

 one (or two) IEEE-1394 cables

Note: The transmission capability of IEEE-1394 cable used with this TV must be S400 (400 Mbps maximum).

 additional A/V cables if your device is analog-compatible

(see “Using analog-compatible IEEE-1394 devices” below).

Two bi-directional IEEE-1394 ports

Using analog-compatible IEEE-1394 devices

Some digital IEEE-1394 devices are compatible with analog signals. For example, some D-VHS VCRs can record and play VHS or S-VHS format videos. Such devices allow you to play analog tapes that you rented or recorded, or record analog programs from antenna or Cable TV systems. To use the IEEE-1394 device’s analog features, you need to connect the device to the TV using standard A/V cables (or S-video plus audio cables) in addition to connecting the IEEE-1394 cable.

Note: If you have an IEEE-1394 device connected to both digital and analog inputs on the TV, the TV automatically switches between analog and digital modes, as needed, when the initial device access is initiated using the TheaterNet button. See page 44 for details on using the TheaterNet feature.

Supported signals

The IEEE-1394 ports support the signals listed below only. Although incompatible video, audio, and digital control signals

cannot be decoded by the TV, these signals may be passed through the IEEE-1394 cable to other compatible devices.

Incompatible devices may not appear in the TheaterNet

™

menu.

•MPEG-2 digital video signals

Other digital video signals—such as DV video—are incompatible and must be decoded by the source device and sent to the TV as analog video (composite or S-video).

• Dolby Digital and MPEG digital audio signals

Other digital audio signals (such as DPM, MP3, and DTS) are incompatible and cannot be decoded by the TV.

•EIA-775 and AV/C digital control

Your TV can serve as the control center for many devices that are compatible with EIA-775 or AV/C IEEE-1394 control standards (described below).

The TV cannot control IEEE-1394 devices that use any other control standards.

– EIA-775 digital control allows tuning devices (such as

Cable boxes) to send simple graphics; however, this standard does not allow the TV to control the Cable box through IEEE-1394.

– AV/C (audio/video control) provides basic control (such

as power, play, stop rewind, fast-forward, pause, and record), as applicable to the specific device.

Using TheaterNet™ on-screen device control

You can use the TheaterNet feature to control some IEEE-1394 devices using on-screen control icons. See page 44 for details on setting up and using the TheaterNet feature.

Note: If the TheaterNet feature does not control your IEEE-1394, you can try using IR pass-through with the TV’s remote control (page 21) or use the device’s remote control.

TV back panel

{

NOTE: NEVER CONNECT THIS TV TO A PERSONAL COMPUTER (PC).

THIS TV IS NOT INTENDED FOR USE WITH A PC.

From IEE E-1394 devices (such as AVHD or D-VHS)

HM94(E)012-25(2B-Cnct) 8/31/04, 12:53 PM22

Chapter 2: Connecting your TV

Connecting IEEE-1394 video devices (continued)

IEEE-1394 device initialization

When you connect a new IEEE-1394 device to the TV and turn it on, the device immediately announces its presence to the TV (and other networked IEEE-1394 devices, if any), and the following device initialization screen automatically appears.

Note: With some devices, it may take up to one minute for this screen to appear.

1. If you have connected your IEEE-1394 device to an analog input also, use the

yzx •

buttons to select the input in the ANALOG INPUT USED field; otherwise, leave it set to “None.” (See “Using analog-compatible IEEE-1394 devices” on page 22.)

2. If you want to label the device, highlight EDIT LABEL and press ENTER.

3. Press the

yzx •

buttons to select a character for the first

space and then press ENTER.

4. Repeat step 3 to enter the rest of the characters.

5. Highlight SAVE and press ENTER to save the information.

Note:

•The TV may not recognize non-A/V or non-compatible IEEE-1394 devices; however, these devices may still be available to other compatible IEEE-1394 devices on the network.

•You may be able to use the TV’s remote control to operate some compatible IEEE-1394 devices. You must first program the remote control to recognize the device (see Chapter 3). If you have an IEEE-1394 Cable box or satellite receiver, you may need to use the remote control that came with the device.

•Toshiba is not liable for the operation of any IEEE-1394 device other than the Toshiba Symbio AVHD recorder.

Connecting an AVHD (external hard drive) or D-VHS digital recorder

You can connect an IEEE-1394 compatible D-VHS or AVHD (audio/video hard drive) digital recorder (such as Toshiba’s Symbio

™

160HD4 AVHD) to record high definition and standard definition material from either tuner and control live TV (pause, rewind, etc.).

When you connect a D-VHS or AVHD device to the TV:

• The remote control keys (LIVE, REW, PAUSE, PLAY, FF,

etc.) are automatically activated to allow control of live TV.

• The TV Guide On Screen system is automatically configured

to allow recording to the device.* See Chapters 5 and 7 for details. Also see page 49 for details on setting the AVHD device skip time.

•Some programs may not be recorded due to copy protection

restrictions.

NOTE: NEVER CONNECT THIS TV TO A PERSONAL COMPUTER (PC).

THIS TV IS NOT INTENDED FOR USE WITH A PC.

This TV is compatible with the new Toshiba

Symbio

™

Audio/Video Hard Drive Recorder!

Toshiba’s Symbio model 160HD4 is an audio/video hard drive (AVHD) recorder designed specifically for high definition television (HDTV). The Symbio AVHD recorder offers control over digital video recording and playback. Think of it as a “tapeless VCR” for digital television. You can pause, rewind, or use instant replay, so you’ll never miss a thing. However, unlike a traditional VCR, where you wait for a program to finish recording before you start watching it, the Symbio AVHD recorder allows you to “pause live TV.” For example, you can pause, rewind, and play back a program while it is being recorded. Since there is no tape to rewind, you can view a program that started recording 20 minutes ago, even while it is still recording.

Symbio also offers one-touch recording* of both standard and High Definition programs through the no-fee TV Guide On Screen interactive program guide built in to this TV.

___________ *If you are connecting a Symbio AVHD recorder, in order to use its full

functionality, you must first set up the TV Guide On Screen system (see Chapter 5).

HM94(E)012-25(2B-Cnct) 8/31/04, 12:53 PM23

Chapter 2: Connecting your TV

Connecting IEEE-1394 video devices (continued)

Important information regarding

IEEE-1394 device interconnection

Note:

• Do not loop the last device in the chain back to the TV.

If the device chain is looped, the TV may not work properly with the other devices in the chain.

• Place devices with the slowest communication speed at the end of each chain. If a device with a slower communication speed is placed ahead of a faster device in the chain, the signal from the slower device will interfere with the signal from the faster device. To determine the communication speed of an IEEE-1394 device, look for an “S” number near the device’s IEEE-1394 connector. The higher the “S” number, the faster the device. If your device is not marked with an “S” number, look in the device’s user manual or call the device manufacturer’s technical support number.

• If your IEEE-1394 device has a two-position power

switch, place the device at the end of the chain or leave the power switch ON at all times. If the power switch is OFF,

it will interfere with signals from devices behind it in the chain.

• The maximum length for an IEEE-1394 cable between

each device is 15 feet.

•This TV is an IEEE-1394A device. The IEEE-1394B protocol is faster and intended to allow for longer distances between devices and multi-room systems. IEEE-1394A–to–IEEE-1394B converters (available at some electronics suppliers) may allow compatibility of IEEE-1394B devices with your existing IEEE-1394A devices.

•The transmission capability of IEEE-1394 cable used with this TV must be S400 (400 Mbps maximum).

IEEE-1394 device management

The IEEE-1394 device information is saved in the TV’s memory. You can edit this device information (for example, to edit the device name, change the analog input information, or delete the device information from the TV’s memory if you no longer use that device).

To edit the IEEE-1394 device information:

1. Press MENU and open the SETUP menu.

2. Highlight INSTALLATION and press ENTER. (A new set of INSTALLATION menu icons will appear on-screen, as shown in step 3 below).

3. Open the DEVICES menu, highlight IEEE-1394 DEVICES, and press ENTER.

Devices

IEE-1394 Devices TheaterNet Devices

Navigate Select Back Exit

DVD RTN

CH RTN

EXIT

4. Highlight the device you want to edit and press ENTER.

5. Follow the on-screen prompts to modify the device information.

HM94(E)012-25(2B-Cnct) 8/31/04, 12:53 PM24

Chapter 2: Connecting your TV

After you connect your devices to the TV, you will need to connect the G-LINK cable (either of the dual-wand IR blaster cables included with your TV) from your VCR and Cable box (if applicable) to the G-LINK jack on the TV.

Note: TV Guide On Screen program data is available through the ANT-1 and ANT-2 antenna inputs and also through the VIDEO 1 inputs if you have a cable box connected to VIDEO 1. TV Guide On Screen program data is not available through any other inputs on this TV. See the connection information on pages 13–25.

The G-LINK connection is necessary to enable the following features of your TV Guide On Screen™ system:

•If you have a Cable box, you need to connect the G-LINK cable from the Cable box to the G-LINK jack to receive the TV Guide On Screen system’s program listings for your Cable service.

•If you have a VCR, you need to connect the G-LINK cable from the VCR to the G-LINK jack to use the TV Guide On Screen system’s recording features.

G-LINK™ connection

This connection is necessary for the TV Guide On Screen™ system to work with your cable box to receive program listings and to enable TV Guide On Screen recording features with your VCR.

Note: This connection is

not necessary for AVHD or D-VHS recording devices. See pages 23 and 49 for further details.

TheaterNet

OUT

AUDIO

S-VIDEO

VIDEO 1 VIDEO 2

OUT 1

G-LINK

HDMI IN

DIGITAL

AUDIO OUT

ANT (75

)

ANT1

(CABLE)

ANT2

CableCARD™

COLOR

STREAM

HD-1

COLOR

STREAM

HD-2

VAR

AUDIO

TheaterNet

OUT 2

S-VIDEO

IEEE1394

EJECT

L/ MONO

AUDIO

VIDEO

L/ MONO

AUDIO

VIDEO

L/ MONO

AUDIO

VIDEO

AUDIO

Back of TV

Front of VCR

Front of Cable box

Infrared

sensor

G-LINK (IR blaster) cable wand (approx. 1 inch from device)

TheaterNet

If you cannot locate the device’s infrared sensor:

1. Turn OFF the device.

3. If the device turns on, the place the remote control touched the device is the location of the sensor.

4. If the device does not turn on, move the remote control slightly to the right and press POWER again.

5. Repeat step 4 until you locate the device’s infrared sensor.

To connect to the G-LINK jack:

1. Locate the infrared sensor on the front of your VCR or Cable box. The sensor is marked on some devices.*

2. Align one of the G-LINK (IR blaster) cable’s wands about 1 inch away from the infrared sensor on the front of the VCR and attach it using double-sided mounting tape.

If you have a Cable box, attach the other wand in a similar manner. (See illustration at right.)

Note: If you do not have a Cable box, coil the second wand with a rubber band and leave it behind the TV.

3. Plug the G-LINK (IR blaster) cable’s plug into the TV’s G-LINK jack.

For details on setting up the TV Guide On Screen system:

See Chapter 5.

For details on using the TV Guide On Screen interactive program guide:

See Chapter 7.

HM94(E)012-25(2B-Cnct) 8/31/04, 12:53 PM25

16.4 ft (5m)

Using the remote control

Note: The error message “Not

Available” will appear if you press a key for a function that is not available.

CT-90216

ACTION

ENTER

–

100

+10

The buttons used for operating the TV only are described here. For a complete list of the remote control’s functions, see the remote control functional key chart on pages 28–29.

POWER

turns the TV on and off. Press POWER to turn on the TV. The red LED indicator on the

TV front touchpad will be illuminated. Press POWER again to turn off the TV.

Note: The Quick Restart setting will affect the amount of time it takes for the picture to appear when you turn on the TV. See page 50 for details.

SLEEP

accesses the sleep timer (page 86).

LIGHT

The first press of the LIGHT button lights the keypad and turns on the Illumination mode. With the Illumination mode on, pressing any other key lights the keypad for 5 seconds (10 seconds if you’re in programming mode). Subsequent presses of the LIGHT button toggle between turning the Illumination mode on and off.

Channel Numbers (0–9, –/100)

directly tune channels. The “–” button is used to tune digital

channels (page 68).

INPUT

selects the video input source (page 67).

MODE

cycles through the six device modes: TV, CBL/SAT, VCR/PVR, DVD, AUDIO1, and

AUDIO2. The mode indicator light will remain lit for a few seconds (page 27).

PIC SIZE

cycles through the five pictures sizes: Natural, TheaterWide 1/2/3, and Full (page 70).

TheaterNet DEVICE

displays a list of available TheaterNet devices (page 44).

TheaterNet CTRL

accesses the on-screen IR device control icons (page 44).

accesses the menu system (pages 34 and 35).

TV GUIDE

opens the TV Guide On Screen system (Chapter 7).

INFO

provides detailed information on highlighted items in the TV Guide On Screen system

(Chapter 7).

ENTER

activates highlighted items in the main menu system and the TV Guide On Screen system.

Arrow buttons (

yzx •

) select or adjust programming menus.

CH yz

cycles through programmed channels when no menu is on-screen (41); functions as page up/down when a menu is on-screen or when the TV Guide On Screen system is open (Chapter 7).

VOL yz

adjusts the volume level.

EXIT

closes on-screen menus and the TV Guide On Screen system.

CH RTN

returns to the last viewed channel (page 68), or stops the picture viewer

slide show (page 83).

Live

returns viewing of the TV back to the live program, while continuing to record

to the Toshiba Symbio

™

AVHD recorder (pages 23 and 49).

RECALL

displays TV setting information on-screen (page 87).

MUTE

reduces or turns off the sound (page 79).

TV/VCR

selects TV mode to view one program while recording another.

SKIP/SEARCH SS

and

jump forward and backward one day in the TV Guide

On Screen listings (Chapter 7).

LIST

displays the Toshiba Symbio™ AVHD recorder play list (if available) (page 23).

FAV C H yz

tunes to the next higher/lower favorite channel (page 43).

VCR+

accesses the TV Guide On Screen manual recording function.

SPLIT

turns the POP feature on and off (page 73).

PIC MODE

selects the picture mode (page 76).

FAV SCAN

accesses the favorite channel search function (page 75).

FREEZE

freezes the main picture in the double-window (page 74).

Learning about the remote control

Point remote control toward

remote sensor on front of TV.

Remote control effective range

HM94(E)026-33(3-RC) 8/31/04, 1:07 PM26

Chapter 3: Using the remote control

MODE Device mode control after programming

1) TV Toshiba TV

2) CBL/SAT

3) VCR/PVR

4) DVD Multi-brand video/audio devices

5) AUDIO 1

6) AUDIO 2

Note:

Although your new TV’s remote control includes codes for many devices, it may not include codes for some or all of the features on certain devices you wish to control. If you are unable to program the TV’s remote control to operate your device or some of the features on that device, use the device’s remote control or the controls on the device.

MODE

ACTION

ENTER

–

100

+10

Your TV remote control has one dedicated TV mode and five programmable multi-brand modes: CBL/SAT, VCR/PVR, DVD, AUDIO 1, and AUDIO 2. The default device modes and programmable device modes are listed below.

Note: The TV remote control is preprogrammed to operate most Toshiba devices. If you own a non-Toshiba device or a Toshiba device that the remote control is not preprogrammed to operate, you will need to program the remote control. See “Programming the remote control to operate your other devices” on page 30.

MODE Default device mode control (before programming)

1) TV Toshiba TV

2) CBL/SAT Toshiba Satellite receiver

3) VCR/PVR Toshiba VCR

4) DVD Toshiba DVD

5) AUDIO 1 Pioneer Audio receiver

6) AUDIO 2 Pioneer LD

Using the remote control MODE button to control your other devices

To install the remote control batteries:

CAUTION: Always dispose of batteries in a designated disposal location. Never throw batteries into a fire.

1. Slide the battery cover off the back of the remote control.

2. Install two “AA” size alkaline batteries. Match the + and – symbols on the batteries to the symbols on the battery compartment.

3. Slide the battery cover on to the remote control until the lock snaps.

Installing the remote control batteries

You can directly select the device mode by pressing the corresponding number button (1-6) while pressing the MODE button.

Number (1-6)

Note:

• Batteries should always be disposed of with the

environment in mind. Always dispose of batteries in accordance with applicable laws and regulations.

• Never mix battery types or use new and used

batteries in combination.

• When necessary to replace batteries in the remote

control, always replace both batteries with new ones.

• Always remove batteries from remote control if they

are dead or if the remote control is not to be used for an extended period of time. This will prevent battery acid from leaking into the battery compartment.

HM94(E)026-33(3-RC) 8/31/04, 1:08 PM27

Chapter 3: Using the remote control

Remote Control functional key chart

Key Label

Toshiba TV Cable Satellite VCR DVD/LD Receiver CD PVR

(TV) (CBL/SAT) (CBL/SAT) (AUDIO) (AUDIO) (VCR) MODE Remote control device mode selection LIGHT Lights the remote key, and toggles between enabled and disabled Illumination mode.*

SLEEP Sleep timer --- --- --- --- --- --- --POWER Power Power Power Power Power Power Power Power 1Digit 1 Digit 1 Digit 1 Digit 1 Digit 1 AV input 1 Digit 1 Digit 1 2Digit 2 Digit 2 Digit 2 Digit 2 Digit 2 AV input 2 Digit 2 Digit 2 3Digit 3 Digit 3 Digit 3 Digit 3 Digit 3 AV input 3 Digit 3 Digit 3 4Digit 4 Digit 4 Digit 4 Digit 4 Digit 4 AV input 4 Digit 4 Digit 4 5Digit 5 Digit 5 Digit 5 Digit 5 Digit 5 CD Digit 5 Digit 5 6Digit 6 Digit 6 Digit 6 Digit 6 Digit 6 Tuner Digit 6 Digit 6 7Digit 7 Digit 7 Digit 7 Digit 7 Digit 7 Phono Digit 7 Digit 7 8Digit 8 Digit 8 Digit 8 Digit 8 Digit 8 Cassette Digit 8 Digit 8 9Digit 9 Digit 9 Digit 9 Digit 9 Digit 9 Aux Digit 9 Digit 9 0Digit 0 Digit 0 Digit 0 Digit 0 Digit 0 --- Digit 0, 10 Digit 0 100/– – (digital --- – (sub 100 +10 --- --- ---

- separator) channel)

INPUT TV/Video TV TV VCR input TV --- TV TV

select

PIC SIZE Selects the TV TV TV TV TV TV TV

image shape.

MENU/ Menu/ --- Action, --- Menu --- --- Menu ACTION Guide Menu Menu

TV GUIDE/SETUP

TV Guide --- Guide --- DVD setup --- --- Guide

INFO/TITLE Guide Info --- INFO --- TITLE= --- --- INFO

Top menu

TheaterNet

Theater Net

--- --- --- Subtitle --- ---

ADVANCE

DEVICE/SUBTITLE

Device

TheaterNet

Theater Net

--- --- --- Audio --- --- ---

CTRL/AUDIO

Control

ENTER Enter --- Enter, Select --- Enter --- --- Enter

y Menu select --- Menu select --- Menu select --- --- Menu select

up up up up

z Menu select --- Menu select --- Menu select --- --- Menu select

down down down down

x • Menu select --- Menu select --- Menu select --- --- Menu select

left/right left/right left/right left/right

EXIT/ Exit --- Exit --- DVD clear --- --- --DVD CLEAR

yz Channel Channel Channel Channel --- Channel --- Channel

PAGE +/– up/down, up/down up/down up/down up/down up/down

Page up/down

VOL yz Volume Volume Volume Volume Volume Volume Volume Volume

up/down*2up/down*2up/down*2up/down*2up/down*2up/down*2up/down*2up/down*

CH RTN/ Previous Previous Previous --- DVD --- --- --DVD RTN channel channel channel return

Live Live --- --- --- --- --- --- Live TV RECALL On-screen

--- ---

On-screen On-screen --- --- ---

display display display

HM94(E)026-33(3-RC) 8/31/04, 1:08 PM28

Chapter 3: Using the remote control

Key Label

Toshiba TV Cable Satellite VCR DVD/LD Receiver CD PVR

(TV) (CBL/SAT) (CBL/SAT) (AUDIO) (AUDIO) (VCR) MUTE

Sound mute*2Sound mute*2Sound mute*2Sound mute*2Sound mute*2Sound mute*2Sound mute*2Sound mute*

SLOW/ •--- --- --- Slow FWD Slow FWD --- --- Slow FWD DIR x--- --- --- --- Slow REW --- --- ---

SKIP/

• Skip FWD

--- --- --- Skip FWD

---

Skip FWD ---

x Skip REW

--- --- --- Skip REW

---

Skip REW ---

REW Rewind --- --- Rewind Rewind

---

Rewind Rewind

PAUSE/STEP Pause --- --- Pause Pause

---

Pause Pause

PLAY Play --- --- Play Play

---

Play Play FF Fast FWD --- --- Fast FWD Fast FWD --- Fast FWD Fast FWD TV/VCR

--- ---

TV/SAT TV/VCR --- --- --- Reverse DISC/AM/FM --- --- --- --- Disc shift AM/FM Disc shift Replay STOP Stop

--- ---

Stop Stop --- Stop Stop

REC REC Menu --- --- Record --- --- --- Record

(Single Click)

(Double Click) (Double Click)

LIST LIST

--- --- --- --- --- --- ---

FAV CH

FAV channel --- --- --- --- --- --- --up/down

VCR

--- --- --- --- --- --- ---

SPLIT

Split

TV TV TV TV TV TV TV PIC MODE PIC MODE TV TV TV TV TV TV TV FAV SCAN FAV SCAN --- --- --- --- --- --- --FREEZE

Freeze

TV TV TV TV TV TV TV

Notes:

• “---” will send nothing.

•“ TV” will jump to TV.

•“ VCR” will jump to last active VCR or DVD. (“Last active VCR/DVD” is the mode that remains for a minimum of 5 seconds, or if a key is pressed in that mode.)

Backlight key is toggle. Does not send IR signal.

* 2Volume will punch through to TV by default. When the volume is unlocked, all the devices will have their own volume if their ID has

volume data. The AUD modes (receiver, CD) will have their own volume if volume lock is done to TV, CBL/SAT, VCR/PVR, or DVD mode. See “Using the volume lock feature” on page 31.

Remote Control functional key chart (continued)

HM94(E)026-33(3-RC) 8/31/04, 1:08 PM29

Chapter 3: Using the remote control

Programming the remote control to operate your other devices

Searching and sampling the code of a device (8500)

If you do not know the device code for a particular device, you can cycle the remote control through the available codes for that device mode and sample the functions to find the code that operates the target device. The keys available to be sampled, provided they are applicable to that mode, are POWER, 1, VOL y, CH y, and PLAY. Invalid keys will be ignored while in program mode.

To cycle through each available device code and sample its functions:

1. Press MODE to select the mode you want to set up.

2. While holding down RECALL, press 8–5–0–0. The remote control will enter program mode.

3. Point the remote control at the target device and press POWER (or other function buttons that are available to be sampled).

4. If the device responds to the remote control:

Press RECALL to store the device code. The mode indicator will blink twice and the remote control will exit the program mode.

If the device does not respond to the remote control:

Press y, and then press POWER. Repeat this step until the device responds to the remote control, and then press RECALL.

Note: When a search cycle is completed, the mode indicator will blink three times. The remote control will begin to cycle through the available codes again. If no key is pressed within 10 seconds while programming, the remote control will exit the program mode and return to the previous code.

Device code setup

1. Refer to the multi-brand remote control device code table on pages 32–33 to find the code for the brand of your device.

If more than one code is listed, try each one separately until you find the one that works.

2. Press MODE until the Mode indicator for the device (CBL/SAT, VCR/PVR, DVD, AUDIO 1, AUDIO 2) lights up.

3. While holding down the RECALL button, press the Channel Number buttons to enter the four-digit code for your brand of device. If a valid code is entered, the mode indicator will blink twice. If an invalid code is entered, the mode indicator will blink one long blink.

4. Point the remote control at the device and press POWER to test the code.

If the device responds to the remote control:

You have entered the correct code.

If the device does not respond to the remote control:

You may have entered the wrong code. Repeat steps 3 and 4 using another code.

Note: In addition to POWER, confirm that all necessary keys on the TV remote control operate your device. If some keys are not operational, repeat the device code setup using another code (if other codes are listed for your device). If, after trying all listed codes, the necessary keys do not operate your device, use the device’s original remote control.

5. Press MODE to select the TV mode to control the TV.

Note:

• Although the TV remote control includes codes for many devices, it may not include codes for some or all of the features on certain devices you wish to control. If you are unable to program the TV remote control to operate your device or some of the features on that device, use the device’s remote control or the controls on the device.

• Each time you change the batteries you will need to reprogram the remote control.

• Some newer VCRs respond to either of two codes. These VCRs have a switch labeled “VCR1/VCR2.” If your VCR has this kind of switch and does not respond to the codes for your VCR brand, set the switch to the other position (“VCR1” or “VCR2”) and reprogram the remote control.

ACTION

ENTER

–

100

+10

POWER

Numbers

MODE

VOL y/z

RECALL

HM94(E)026-33(3-RC) 8/31/04, 1:08 PM30

+ 78 hidden pages