Toshiba 50HP82, 50HP82SVM, 50HP82S, 50XP26 Schematic

SERVICE MANUAL

DOCUMENT CREATED IN JAPAN, Mar., 2005

REVISION 1

PLASMA MONITOR

50HP82,50XP26H

FILE NO. 050-200221

50XP26K,50XP26R

SAFETY PRECAUTIONS .................................................................................................................................. 2-1

USER’S MANUAL .............................................................................................................................................. 3-1

TROUBLESHOOTING ....................................................................................................................................... 4-1

METHOD OF ADJUSTMENTS .......................................................................................................................... 5-1

METHOD OF DISASSEMBLY ........................................................................................................................... 6-1

PACKAGING...................................................................................................................................................... 7-1

PART LIST ......................................................................................................................................................... 8-1

CONNECTION DIAGRAMS............................................................................................................................... 9-1

BLOCK DIAGRAM ........................................................................................................................................... 10-1

1-1

SAFETY PRECAUTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT OPEN REAR COVER. NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol warns the user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any part inside of this unit.

This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems.

ATTENTION

RISQUE D'ELECTROCUTION

NE PAS OUVRIR

ATTENTION: POUR EVITER LES RISQUES D' ELECTROCUTION, NE PAS ENLEVER LE CONVERCLE ARRÈRE. AUCUN DES

ELEMENTS INTERNES NE DOIT ETRE REPARE PAR L'UTILISATEUR. NE CONFIER L' ENTRETIEN QU'A UN PERSONNEL QUALIFIE.

L'éclair fléché dans un triangle équilatéral est destiné à avertir l'utilisateur de la présence, dans l'appareil, d'une zone non-isolée soumise à une haute tension dont l'intensité est suffisante pour constituer un risque d'électrocution.

Le point d'exclamation dans un triangle équilatéral est destiné à attirer l' attention de l'utilisateur sur la présence d'informations de founctionnement et d'entretien importantes dans la brochure accompagnant l'appareil.

WARNING

HEATSINK MAY BE ENERGIZED. TEST BEFORE TOUCHING.

2-1

SAFETY PRECAUTIONS

1. Before returning an instrument to the customer, al- ways make a safety check of the entire instrument, in-

cluding, but not limited to, the following items. a. Be sure that no built-in protective devices are

defective and/or have been defeated during servicing. (1) Protective shields are provided on this chassis to protect both the technician and the customer. Correctly replace all missing protective shields, including any removed for servicing convenience. (2) When reinstalling the chassis and/or other assembly in the cabinet, be sure to put back in place all protective devices, including,but not limited to, nonmetallic control knobs,insulating fishpapers,adjustment and compartment covers/shields, and isolation resistor/capacitor networks. Do not operate this

instrument or permit it to be operated without all protective devices correctly installed and functioning.

b. Be sure that there are no cabinet openings

through which an adult or child might be able to insert their fingers and contact a hazardous voltage. Such opening include,but are not limited to, (1) spacing between the picture tube and the cabinet mask, (2) excessively wide cabinet ventilation slots, and (3) an improperly fitted and/or incorrectly secured cabinet back cover.

c. Leakage Current Hot Check — With the instru-

ment completely reassembled,plug the AC line cord directly into a 240V AC outlet. (Do not use an isolation transformer during this test.) Use a leakage current tester or a metering system that complies with American National Standards Institutes (ANSI) C101.1 Leakage Current for Appliances and Underwriters Laboratories(UL)

1950. With the instrument AC switch first in the ON position and then in the OFF position, measure from a known earth ground (metal waterpipe, conduit,etc.) to all exposed metal parts of the instrument(antennas, handle bracket, metal cabinet, screwheads, metallic overlays, control shafts,etc.), especially any exposed metal parts that offer an electrical return path to the chassis. Any current measured must not exceed 3.5 milliamp. Reverse the instrument power cord plug in the outlet and repeat test.ANY MEASUREMENTS NOT WITHIN

THE LIMITS SPECIFIED HEREIN INDICATE A POTENTIAL SHOCK HAZARD THAT MUST BE ELIMINATED BEFORE RETURNING THE INSTRUMENT TO THE CUSTOMER.

AC Leakage Test

(READING SHOULD NOT BE ABOVE

DEVICE UNDER

TEST

TEST ALL EXPOSED METAL SURFACES

3-WIRE CORD

ALSO TEST WITH PLUG REVERSED (USING AC ADAPTER PLUG AS REQUIRED)

LEAKAGE CURRENT

TESTER

+–

3.5 mA)

EARTH

GROUND

2. Read and comply with all caution and safety-related notes on or inside the Monitor cabinet, on the Projection Monitor chassis, or on the picture tube.

3. Design Alteration Warning — Do not alter or add to the mechanical or electrical design of this unit. Design alterations and additions, including, but not limited to, circuit modifications and the addition of the items such as auxiliary audio and/or video output connections might alter the safety characteristics of this Monitor and create a hazard to the user. Any design alterations or additions will void the manufacturer's warranty and will make you,the servicer,responsible for personal injury or property damage resulting therefrom.

4. Hot Chassis Warning — a. Some MultiSync Monitor chassis are electrically connected directly to one conductor of the AC power cord and may be safely serviced without an isolation transformer only if the AC power plug is inserted so that the chassis is connected to the ground side of the AC power source. To confirm that the AC power plug is inserted correctly, with an AC voltmeter measure between the chassis and a known earth ground. If a voltage reading in excess of 1.0V is obtained, remove and reinsert the AC power plug in the opposite polarity and again measure the voltage potential between the chassis and a known earth ground. b. Some Plasma chassis normally have 85V AC (RMS), between chassis and earth ground regardless of the AC plug polarity. These chassis can be safely serviced only with an isolation transformer inserted in the power line between the receiver and the AC power source, for both personnel and test equipment protection. c. Some Plasma chassis have a secondary ground systems in addition to the main chassis ground. This secondary ground system is not isolated from the AC power line. The two ground system are electrically separated by insulating material that must not be defeated or altered.

2-2

SAFETY PRECAUTIONS

5. Observe original lead dress. Take extra care to assure correct lead dress in the following areas: a. near sharp edges, b. near thermally hot parts— be sure that leads and components do not touch thermally hot parts, c. the AC supply, d. high voltage, and e. antenna wiring. Always inspect in all areas for pinched, out-of-place, or frayed wiring. Do not change spacing between components, and between components and the printed-circuit board. Check AC power cord for damage.

6. Components,parts, and/or wiring that appear to have overheated or are otherwise damaged should be replaced with components, parts, or wiring that meet original specifications. Additionally,determine the cause of overheating and/or damage and, if necessary, take corrective action to remove any potential safety hazard.

7. PRODUCT SAFETY NOTICE —Many MultiSync

Monitor electrical and mechanical parts have spe-

cial safety-related characteristics some of which are often not evident from visual inspection, nor can the protection they give necessarily be obtained by replacing them with components rated for higher voltage, wattage, etc. Parts that have special safety characteristics are identified in this service data by shading with a mark on schematics and by shading or a mark in the parts list. Use of a substitute replacement part that does not have the same safety characteristics as the recommended replacement part in this service data parts list might create shock, fire, and/or other hazards.

2-3

PRECAUTIONS DE SECURITE

1. Avant de remettre un appareil à un client, faire

toujours d'abord un examen de sécurité de l'appareil en entier comprenant, mais ne s'y limitant pas les points cités ci-dessous: a. Vérifier qu' aucun des dispositifs de protection ne

soit défectueux ou n' ait été endommagé pendant les travaux. (1) Les volets protecteurs sur ce châssis ont été montés pour protéger aussi bien le technicien que le client. Remplacer correctement tous les volets protecteurs manquants, aussi bien que ceux qui ont pu être enlevés pour la commodité des travaux. (2) Quand vous remettez le châssis ou d'autres assemblages ensemble dans le coffret, vérifier qu' ont été remis à leur place tous les dispositifs de protection, comprenant mais ne s' y limitant point, les boutons de contrôle non-métalliques, les feuilles d'isolation, les couverture/volets de l'ajustement et du compartiment, et l'isolation des réseaux résistance/condensateur. Ne pas

travailler sur cet appareil ni permettre qu'y soit effectué un travail sans que tous les dispositifs de protection n' y soient correctement installés fonctionnants.

b. Bien vérifier qu'il n'y ait aucune ouverture sur le

coffret qui ne puisse permettre à un adulte ou à un enfant d'y faire pénétrer ses doigts et attraper une décharge électrique. De telles ouvertures comprendraient sans pour autant s'y limiter (1) l'espace entre le tube à images et le coffret de l'eppareil, (2) les espaces excessivement ouverts pour la ventilation et (3) la couverture arrière du coffret improprement fixée ou incorrectement protegée.

c. Vérification de courant de fuite

L'appareil ayant été complètement réassemblé, brancher-le à une prise de courant de 240V. (Ne pas se servir d'un transformateur

d'isolation pendant ce test). Se servir d'un vérificateur de courant d'excitation ou d'un système de mesure conforme aux normes ANSI (American National Standards Institute) C101.1 Leakage Current for Appliances et U. L (Underwriters Laboratories) 1950. Le bouton de l'appareil en position "Marche" et ensuite en position "Arrêt", mesurer à partir d'une prise de terre (métallique tuyauterie, conduite, etc...) à toutes les pièces métalliques de l'appareil exposées (antennes, poignet métalliques, coffren métallique, tête des vis, surfaces métalliques, traits de contrôle, etc.) surtout à toutes les pièces métalliques exposées qui peuvent reconduire le courant au châssis. En aucun cas, la mesure du

courant ne doit dépasser 3.5 milliamp. Inverser la fiche de courant de l'appareil dans la prise et répéter le test. Tout mesurage ne s'arrêtant

pas aux limites spécifiées icicomporte un risque de décharge électrique dangereux, qui doit être éliminé, avant que l'appareil ne soit remis au client.

EXAMEN DE COURANT D'EXCITATION

(LA MESURE DU COURANT NE DOIT PAS DEPASSER

3.5 MILLIAMP)

DISPOSIT IF

SOUS

L ' EXAMEN

EXAMINER TOUTES LES PIECES METALLIQUES DEL' APPAREIL EXPOSEE

3-CORDES DE FIL

EXAMINER AVEC LA FICHE DE COURANT INVERSEE

(SE SERVIR DE LA FICHE DE COURANT DE L' A DAPTATEUR COMME DEMANDEE)

+–

VERIFICATEUR DE CORANT DE FUITE

PRISE DE TERRE

2. Lire et respecter toutes les mises en garde et notes de sécurité à l'intérieur ou à l'extérieur du coffret du rétro-projecteur, sur le châssis du rétro-projecteur ou sur le tube à images.

3. Mise en garde contre la modification du dessin

Ne pas modifier ni ajouter à la pièce mécanique ou électrique du modèle. Des modifications ou additions, comportant, mais ne s'y limitant pas, des modifications des circuits et l'addition d'éléments tels que des auxilliairs audio et/ou des branchements pour la prise de vidéo, pourrait éprouver la sécurité de ce rétro-projecteur et créer un risque pour l'utilisateur. Tout changement ou addition accomplie annulera la garantie du fabricant et va rendre votre service d'entretien, responsable des

dommages corporels ou de biens en résultant.

4. Mise en garde contre le châssis sous tension

a. Certains châssis de rétro-projecteur sont

électriquement reliés à un conducteur du fil de courant et ainsi peuvent ne comporter aucun risque sans un transformateur d'isolation seulement si la prise de courant est branchée, de manière que le châssis est relié à la prise de terre de la source de courant. Pour s'assurer que la prise de courant est correctement insérée, relever les mesures avec un voltmètre de courant entre le châssis et un point de prise de terre bien connu. Si le voltage indiqué est supérieur à 1,0V, débrancher et reinsérer la prise de courant dans la polarité contraire et une fois de plus remesurer le voltage potentiel entre le câssis et la prise de terre.

2-4

PRECAUTIONS DE SECURITE

b. Certains châssis de moniteur ont habituellement

85V (RMS) entre le châssis et la prise de terre, en fonction de la polarité de la prise de courant. Ces châssis peuvent ne comporter aucun risque seulement avec un transformateur d'isolation inséré dans la ligne de puissance située entre de rétro-projecteur et la source d'électricité, cela pour la protection aussi bien du personnel que du matériel de vérfication.

c. Certains châssis de rétro-projecteur ont un

système secondaire de masse en addition avec le système principal de masse du châssis. Ce système secondaire de masse n'est pas isolé du courant électrique. Les deux systèmes sont électriquement séparés par du matériel d'isolation qu' on vérifiera bien qu'il ne soit ni altéré ni défectueux.

5. Vérifier la couverture originale en plomb. Accorder la plus grande attention à la couverture de plomb notamment aux endroits ci-dessous indiqués. a. Près des bords aigus b. près des parties très chaudes

Vérifier que les composants et les plombs ne

touchent pas les parties très chaudes telles que: c. l'alimentation du courant d. la haute tension e. Ies fils de l'antenne Pousser l'inspection, à tous les endroits, à la recherche des cordes pincées, déplacées ou effilochées. Ne pas changer l'écartement entre composants, et entre composants et le tableau de circuit imprimé. Vérifier que le fil de conduite électrique est en bon état.

6. Les composants, parts (pièces) et/ou fils qui ont été trouvés surchauffés devraient être remplacés avec les composants, pièces et fils s'y reliant avec d'autre qui ont les mêmes spécifications que les originales. De plus, rechercher la cause du surchauffement et/ ou des dommages et si nécessaire, prendre les mesures propres pour prévenir tout risque potentiel.

7. Note sur sûreté de l'appareil

Beaucoup de pièce de rétro-projecteur, qu'elles soient électriques ou mécaniques, ont des dispositions de sécurité qui ne sont pas toujours évidentes d'une simple inspection visuelle et la protection qu'elles donnent nécessairement ne pourront être pas obtenues par les remplaçants avec des composants aux voltages ou watts plus élevés. Les pièces qui ont des caractéristiques particulières de sécurité sont identifiées avec un trait marqué sur les schémas et sont ombragés ou comportent un trait sur la liste des pièces. L'utilisation d'un produit substitutif qui n'aurait pas les mêmes caractéristiques comme il est recommandé dans ces données d'entretien pourrait provoquer une décharge électrique, un feu, et/ou d'autres dangers.

2-5

SAFETY PRECAUTIONS

1 . Cautions for disassembly

(1)For the suspension-type set (No. of workers: 3

to 5 including assistants)

• Take adequate measures in order not to damage the surface of the set or the filter, using a protection mat (vinyl sheet or blanket).

• When relieving the set from the condition of suspension from the ceiling, do not tilt its main body too much by supporting its both sides, while the mounting hooks (top and bottom) are released. (Reasons: If the main body is positioned slantwise, a load is applied to its upper part and there can be danger of making the set fall down carelessly when the set is unhooked.)

• During disassembly, the allocation of personnel should be such that suitable stands or platforms are assuredly arranged to enable the personnel to support the set, standing on both sides of the set. For safety, it is preferable to provide for assistant personnel who can receive the removed set.

• During this removal work, support the set at its frame with hands. Never touch the filter or glass surface. Assistant personnel on the front side should apply hands to the lower part of the casing. [If the casing is strongly hit with a wooden hammer or the like, the unseen side area of the module panel glass may be broken even though the module itself does not seem to have been broken . Therefore , support the frame by hand in order not to drop it.]

The least minimum caut ions for product disassembly

• Secure a working space, arranged as wide as possible.

• Prior to disassembling the set, protect the acrylic surface with an air mat or the like.

• To prevent the thread ridges from being damaged, use an adequate screwdriver.

• Many screws are actually used. Therefore, use two or three containers where these screws can be kept . Never disassemble the inner parts of the module (pipes, etc.).

• When lifting the module from the set, two persons should stand on both sides of the module to hold the stable parts of the junction while they lift the module upright. (If dust or such foreign substance enters in between the module and the filter, moir* or similar problems can arise. In addition, once it enters, it is necessary to take careful measures not to damage the contamination area while removing contaminants.) [Please understand that the replacement of the module may call for an air-blast treatment (air brush) in a clean room.] Complementary caution) In particular, if a conductive foreign matter (such as a metallic chip) is attached to the flexible cable of the module, there can be danger of the occurrence of a phenomenon like wire breakage that is caused by partition breakdown in the module. For this reason, it is necessary to bear in mind that the flow of air blast should be directed only in the predetermined direction at all times.

(2)For the wall-hang type, corner type, or pole unit

mounting set (No. of workers: 2 <generally>)

• Examining a good timing, release the mounting hooks (top and bottom) from the right and the left.

• If the set is installed in an elevated place, provide for firm scaffolds in advance. It is preferable to ask for the support of assistant personnel as in the case of the suspension type.

• During this removal work, try to support the set at its frame with hands. Never touch the filter or glass surface. Assistant personnel on the front side should apply hands to the lower part of the casing. [If the casing is strongly hit with a wooden hammer or the like, the unseen side area of the module panel glass may be broken even though the module itself does not seem to have been broken. Therefore, support the frame by hand in order not to drop it.]

3. Method of returning the set (when returning the set to the manufacturing base in Japan)

• When returning the set, put the set in the speci-

fied package box. Otherwise, swinging and vibration Ioads may be applied to the set during transportation, and this may give rise to destruction of a mounting section, such as gas-hermetically-sealed pipe (glass) of the moduIe.

• When optional parts are also put in the box for

returning, a list of options (accessories) should also be produced and returned, if possible. This arrangement is effective to confirm the owner of the returned items.

• To confirm the user-oriented problem, and for the

purpose of future improvements, a report of reasons for malfunction should also be packed. A definite address should be specified so that the repaired set can be returned and faulty phenomena can be confirmed .

2-6

SAFETY PRECAUTIONS

(Notes)

The component by the name of “module” used in this product is defined as a section that is provided with a digital circuit board (including highvoltage parts) used to emit light in the glass panel part, excluding the surface acrylic fiIter or the tempered glass fiIter. It must be noted that it does never mean the glass panel part only.

2-7

PLASMA MONITOR

50HP82 50XP26H 50XP26K 50XP26R

OWNER'S MANUAL

Important Information

Precautions

Please read this manual carefully before using your Toshiba plasma monitor and keep the manual handy for future reference.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS, UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems.

WARNING

Warning

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Warnings and Safety Precaution

The Toshiba plasma monitor is designed and manufactured to provide long, trouble-free service. No maintenance other than cleaning is required. Use a soft dry cloth to clean the panel. Never use solvents such as alcohol or thinner to clean the panel surface. The plasma display panel consists of fine picture elements (cells). Although Toshiba produces the plasma display panels with more than 99.99 percent active cells, there may be some cells that do not produce light or remain lit. For operating safety and to avoid damage to the unit, read carefully and observe the following instructions. To avoid shock and fire hazards:

1. Provide adequate space for ventilation to avoid internal heat build-up. Do not cover rear vents or install the unit in a closed cabinet or shelves. The unit is equipped with cooling fans. If you install the unit in an enclosure, make sure there is adequate space at the top of the unit to allow hot air to rise and escape. If the monitor becomes too hot, the overheat protector will be activated and the monitor will be turned off. If this happens, turn off the power to the monitor and unplug the power cord. If the room where the monitor is installed is particularly hot, move the monitor to a cooler location, and wait for the monitor to cool for 60 minutes. If the problem persists, contact your Toshiba dealer for service.

2. Do not use the power cord polarized plug with extension cords or outlets unless the prongs can be completely inserted.

3. Do not expose the unit to water or moisture.

4. Avoid damage to the power cord, and do not attempt to modify the power cord.

5. Unplug the unit during electrical storms or if the unit will not be used over a long period.

6. Do not open the cabinet which has potentially dangerous high voltage components inside. If the unit is damaged in this way the warranty will be void. Moreover, there is a serious risk of electric shock.

7. Do not attempt to service or repair the unit. Toshiba is not liable for any bodily harm or damage caused if unqualified persons attempt service or open the back cover. Refer all service to authorized Service Centers.

NOTE: When you connect a computer to this monitor, attach the supplied ferrite cores. If you do not do this, this monitor will not conform to mandatory FCC standards. Attaching the ferrite cores: Set the ferrite cores on both ends of the DVI cable (not supplied), and both ends of the power cable (supplied). Close the lid tightly until the clamps click. Use the band to fasten the ferrite core (supplied) to the DVI cable.

DVI cable (not supplied)

band

core (small)

Power cable (supplied)

core (large)

band

Connector

core (small)

core (large)

To avoid damage and prolong operating life:

1. Use only with 120V 50/60Hz AC power supply. Continued operation at line voltages greater than 120 Volts AC will shorten the life of the unit, and might even cause a fire hazard.

2. Handle the unit carefully when installing it and do not drop.

3. Set the unit away from heat, excessive dust, and direct sunlight.

4. Protect the inside of the unit from liquids and small metal objects. In case of accident, unplug the unit and have it serviced by an authorized Service Center.

5. Do not hit or scratch the panel surface as this causes flaws on the surface of the screen.

6. For correct installation and mounting it is strongly recommended to use a trained,authorized dealer.

7. As is the case with any phosphor-based display (like a CRT monitor, for example) light output will gradually decrease over the life of a Plasma Display Panel.

Recommendations to avoid or minimize phosphor burn-in

Like all phosphor-based display devices and all other gas plasma displays, plasma monitors can be susceptible to phosphor burn under certain circumstances. Certain operating conditions, such as the continuous display of a static image over a prolonged period of time, can result in phosphor burn if proper precautions are not taken. To protect your investment in this plasma monitor, please adhere to the following guidelines and recommendations for minimizing the occurrence of image burn:

* Always enable and use your computer’s screen saver

function during use with a computer input source. * Display a moving image whenever possible. * Change the position of the menu display from time to time. * Always power down the monitor when you are finished

using it.

If the plasma monitor is in long term use or continuous operation take the following measures to reduce the likelihood of phosphor burn:

* Lower the Brightness and Contrast levels as much as

possible without impairing image readability. * Display an image with many colors and color gradations

(i.e. photographic or photo-realistic images). * Create image content with minimal contrast between light

and dark areas, for example white characters on black

backgrounds. Use complementary or pastel color whenever

possible. * Avoid displaying images with few colors and distinct,

sharply defined borders between colors.

How to Attach Options to the Plasma Monitor .... 1

Introduction ..................................................... 2

Introduction to the

Plasma Monitor........................................................ 2

The features you’ll enjoy include:............................... 2

Contents of the Package ........................................... 2

Options .................................................................. 2

Part Names and Function .................................. 3

Front View............................................................... 3

Rear View / Terminal Board ...................................... 4

Remote Control ........................................................ 5

Battery Installation and Replacement ........................... 6

Using the wired remote control mode .......................... 7

Operating Range .......................................................... 7

Handling the remote control ......................................... 7

Installation ...................................................... 8

Connecting Your PC or Macintosh Computer ............... 9

Connections with Equipment that has a Digital Interface ...

Connecting Your Document Camera ........................... 9

Connecting Your VCR or Laser Disc Player .................. 9

Connecting Your DVD Player ..................................... 9

External Speaker Connections.................................. 10

Pin Assignments and Signal Levels

for 15 pin RGB (Analog) ......................................... 11

Pin Configuration and Signal

of the RGB 3 IN Connector (DVI Connector) .............. 11

Basic Operations ............................................. 12

POWER ................................................................ 12

To turn the unit ON and OFF: .................................... 12

VOLUME .............................................................. 12

To adjust the volume:................................................ 12

MUTE ................................................................... 12

To cancel the sound:.................................................. 12

DISPLAY ................................................................ 12

To check the settings: ................................................. 12

DIGITAL ZOOM ..................................................... 12

AUTO ADJUST ...................................................... 12

To adjust the size or quality of the picture

automatically: ............................................................ 12

OFF TIMER ........................................................... 13

To set the off timer: ................................................... 13

To check the remaining time: ..................................... 13

To cancel the off timer ............................................... 13

OSM Controls ................................................. 18

Menu Operations ................................................... 18

Picture Settings Menu ............................................. 20

Adjusting the picture ................................................. 20

Setting the picture mode according to the

brightness of the room ............................................... 21

Setting the color temperature .................................... 22

Adjusting the color to the desired quality ................... 23

Reducing noise in the picture ..................................... 24

Sound Settings Menu .............................................. 25

Adjusting the treble, bass and left/right balance ........ 25

Screen Settings Menu ............................................. 26

Adjusting the Position, Size, Fine Picture,

Picture Adj ................................................................ 26

Function Settings Menu .......................................... 27

Setting the on-screen menu ....................................... 27

Adjusting the position of the menu display ................ 28

Setting the power management for computer images .....

POWER/STANDBY indicator ................................... 30

Setting the gray level for the sides of the screen ......... 31

Setting the picture to suit the movie ........................... 31

Setting RGB3 ADJ..................................................... 32

Reducing burn-in of the screen .................................. 32

Setting the time for “INVERSE”................................ 33

Setting the time for “SCREEN WIPER” .................... 34

Resetting to the default values .................................... 35

Options Settings Menu ............................................ 36

Setting the allocation of the audio connectors ........... 36

Setting the BNC connectors ...................................... 36

Setting a computer image to the correct RGB

select screen ............................................................. 37

Setting high definition images to the suitable

screen size ............................................................... 38

Setting the picture size for RGB input signals ............ 38

Information Menu ................................................. 39

Checking the frequencies, polarities of input signals,

and resolution ........................................................... 39

Setting the language for the menus............................. 39

Setting the video signal format .................................. 40

External Control ............................................. 41

Table of Signals Supported .............................. 55

Supported resolution .............................................. 55

Troubleshooting ............................................. 57

Specifications ................................................. 58

WIDE Operations ............................................. 14

Watching with a wide screen (manual) .................... 14

When watching videos or digital video discs............. 14

When watching high definition video source ............. 14

Watching computer images with a wide screen ......... 15

When “PICTURE SIZE” is set to “OFF” ...................15

MULTI SCREEN Operations ............................... 16

Showing a couple of pictures on the screen

at the same time ................................................... 16

Operations in the Side-by-side mode .......................... 16

Operations in the Picture-in-picture mode .................. 17

Selecting the input signals to be displayed ................. 17

Adjusting the OSM controls...................................... 17

How to Attach Options to the Plasma Monitor

Drawing B

50mm (2")

1340

(52.8")

866

(34.2")

50mm (2")

(2") 50

(2")

Wall

50mm (2")

You can attach your optional mounts or stand to the plasma monitor in one of the following two ways:

* While it is upright. (See Drawing A) * As it is laid down with the screen face down (See Drawing

B). Lay the protective sheet, which was wrapped around the monitor when it was packaged, beneath the screen surface so as not to scratch the screen face.

• This device cannot be installed on its own. Be sure to use a stand or original mounting unit. (Wall mount unit, Stand, etc.)

* See page 2.

• For correct installation and mounting it is strongly recommended to use a trained, authorized Toshiba dealer.

Failure to follow correct mounting procedures could result in damage to the equipment or injury to the installer.

Product warranty does not cover damage caused by improper installation.

* Use only Listed Cart or Stand, or mounting

kit or stand provided by manufacturer.

Drawing A

Ventilation Requirements for enclosure mounting

To allow heat to disperse, leave space between surrounding objects as shown on the diagram below when installing.

Introduction

Introduction to the Plasma Monitor

Toshiba plasma monior is a seamless blend of cutting-edge visual technology and sophisticated design. At 50-inches, with a 16:9 aspect ratio, the Plasma monitor certainly makes a big impression. However, at a mere 4.2 inches/ 107 mm thin, the monitor’s sleek techno-art lines blend in well with your environment. Plasma monitor crisp, vivid image quality will transform data from any graphic medium from PCs to DVD players- into art. And weighing only 98 lbs/ 44.5 kg, it actually can be hung almost anywhere. Toshiba has made sure that a host of multimedia resources can be easily connected and displayed as brilliantly as intended on the plasma monitor.

The features you’ll enjoy include:

• 50-inch screen

• 16:9 aspect ratio

• Capsulated Color Filter (CCF) and black matrix

• 4.2 inch / 107 mm thin

• 98 lbs/ 44.5 kg light

• High-resolution screen: 1365⳯768 pixels

• 160-degrees of off-axis viewing, horizontally and vertically.

• Flicker - and warp - free display provides excellent image geometry even in screen corners

• Not affected by magnetic fields, no color drift or edge distortion.

• VGA, SVGA, XGA, SXGA, UXGA computer signal compatibility

• NTSC, PAL, SECAM, composite and S-Video signal compatibility

• 480P, 1080I, 720P and HDTV signal compatibility

• PCs, VCRs, Laser Disc and DVD player source compatibility

• AccuBlend™ scan conversion automatically converts VGA, SVGA, XGA, SXGA and UXGA signals to the panel’s native resolution

• Advanced Mass Area Sampling Progressive Scan method is employed.

• RGB input (3*), Video input (3), DVD/HD input (2*), Audio input (3), External Control input (1)

• AccuColor control system provides user selectable onscreen color temperature settings

• New Drive Technology

• Component video input terminal for DVD, 15.75kHz

, CR )

(Y, C

• Digital broadcasting source compatibitly

• Seven languages (English, German, French, Italian, Spanish, Swedish, and Japanese)

*You can select RGB source or Component source for

the 5BNC terminal. When selecting an RGB input, the source is switched to the RGB input (3); when selecting a component input, the source is switched to the DVD/ HD input (2).

Contents of the Package

䡺 Plasma monitor

䡺 Power cord

䡺 RGB cable (Mini D-Sub 15-pin to Mini D-Sub 15-

pin connector)

䡺 Remote control with two AAA Batteries

䡺 User’s manual

䡺 Remote cable

䡺 Safety metal fittings*

䡺 Screws for safety metal fitting*

䡺 Ferrite core (small⳯2, large⳯2), band

* These are fittings for fastening the unit to a wall to prevent

tipping due to external shock when using the stand (option). Fasten the safety fittings to the holes in the back of the monitor using the safety fitting mount screws.

Options

• Wall mount unit

• Ceiling mount unit

• Tilt mount unit

• Tabletop stand

• Speakers

• Others

Part Names and Function

Front View

INPUT SELECT VOLUME

PROCEED

VOLUME

DOWN LEFT/— RIGHT/+UP

q PROCEED

Sets the On-Screen Menu (OSM) mode and displays the main menu.

w VOLUME DOWN and UP

Adjusts the volume. Functions as the CURSOR (▲/ ▼) buttons in the On-Screen Menu (OSM) mode.

e LEFT/– and RIGHT/+

Enlarges or reduces the image. Functions as the



CURSOR (

/ ) buttons in the On-Screen Menu

(OSM) mode.

POWER/STANDBY

INPUT SELECT

/EXIT

POWER/STANDBY

t POWER/STANDBY indicator

When the power is on ............................. Lights green.

When the power is in the standby mode ... Lights red.

y Power

Turns the monitor’s power on and off.

u Remote sensor window

Receives the signals from the remote control.

r INPUT SELECT / EXIT

Switches the input, in the following order.

→ VIDEO1 → VIDEO2 → VIDEO3→ DVD/HD

RGB/PC3 ← RGB/PC2 ← RGB/PC1←

Functions as the EXIT buttons in the On-Screen Menu (OSM) mode.

Rear View/ Terminal Board

AC-IN

SPEAKERS MUST

HAVE MORE THAN

7WATT RATING

IMPEDANCE 6 OHM

RIGHT LEFT

SPEAKERS MUST HAVE MORE THAN 7WATT RATING

IMPEDANCE 6 OHM

RIGHT LEFT

VIDEO 1

VIDEO 2

VIDEO 3

)

VIDEO 1

VIDEO 2

VIDEO 3

)

L ( MONO

CB/PB

CR/PR

)

L ( MONO

AUDIO 2 DVD1/ HD1AUDIO 3 AUDIO 1RGB2/DVD2/HD2

RGB 1

R/CR/PR

G/Y

B/CB/PB

)

L ( MONO

RGB 3

(

)

Digital RGB

CONTROL LOCK

ON /OFF

REMOTE CONTROL

EXTERNAL CONTROL

L ( MONO

CB/ PB

CR/ PR

)

L ( MONO

AUDIO 2 DVD1/ HD1AUDIO 3 AUDIO 1RGB2/ DVD2/HD2

RGB 1

R/CR/PR

G/Y

B/CB/PB

)

L ( MONO

RGB 3

(

)

Digital RGB

CONTROL LOCK

ON / OFF

REMOTE CONTROL

EXTERNAL CONTROL

G H

A EXT SPEAKER L and R

Connect speakers here. Maintain the correct polarity.

B VIDEO1, 2, 3

Connect VCR’s, DVD’s or Laser Discs, etc. here.

C DVD1 / HD1

Connect DVD’s, High Definition or Laser Discs, etc. here.

D RGB1

Inputs the analog RGB signal of personal computer, etc.

E RGB2/ DVD2/ HD2

RGB2: Inputs the analog RGB signal. DVD2/ HD2: Connect DVD’s, High Definition or

Laser Discs, etc. here.

F RGB3

(DVI 29pin)

Inputs a digital RGB signal (TMDS).

G CONTROL LOCK

When “CONTROL LOCK” is set “ON”, the buttons on the set’s control panel do not function.

H REMOTE CONTROL

Connect the supplied remote cable here.

I EXTERNAL CONTROL

This terminal is used when power ON/OFF, input selection and AUDIO MUTE and other controls are operated externally (by external control). See also page 41 for external control.

J AUDIO1, AUDIO2, AUDIO3

These are audio input terminals. The input is selectable. Set which video image to allot them to on the menu screen.

K AC IN

Connect the included power cord here.

Remote Control

w RGB/PC

Press this button to select RGB/PC as the source.

→ RGB/PC1 → RGB/PC2 → RGB/PC3

RGB/PC can also be selected using the INPUT SELECT button on the monitor. The input switches as follows each time the button is pressed:

→ VIDEO1 → VIDEO2→ VIDEO3→ DVD/HD RGB/PC3 ← RGB/PC2 ← RGB/PC1 ←

e DVD / HD

Press this button to select DVD/HD as the source. DVD/HD can also be selected using the INPUT SELECT button on the monitor. The input switches as follows each time the button is pressed:

→ VIDEO1 → VIDEO2→ VIDEO3→ DVD/HD RGB/PC3 ← RGB/PC2 ← RGB/PC1 ←

r VIDEO

Press this button to select VIDEO as the source.

→ VIDEO1 → VIDEO2 → VIDEO3

VIDEO can also be selected using the INPUT SELECT button on the monitor. The input switches as follows each time the button is pressed:

→ VIDEO1 → VIDEO2→ VIDEO3→ DVD/HD RGB/PC3 ← RGB/PC2 ← RGB/PC1 ←

q POWER ON/OFF

Switches Power ON/OFF. (This does not operate when POWER/STANDBY indicator of the main unit is off.)

t PROCEED

Press this button to access the OSM controls. Press this button during the display of the main menu to go to the sub menu.

y CURSOR (▲ / ▼ /



/ )

Use these buttons to select items or settings and to adjust settings or switch the display patterns.

u EXIT

Press this button to exit the OSM controls in the main menu. Press this button during the display of the sub menu to return to the main menu.

i POINTER

Press this button to display the pointer.

o ZOOM (+ /–)

Enlarges or reduces the image.

!0 VOLUME (+ /–)

Adjusts the volume.

!1 MUTE

Mutes the sound.

!2 WIDE

The type of broadcast is detected automatically, and the recommended wide screen is set.

!3 DISPLAY

Displays the source settings on the screen.

!4 OFF TIMER

Activates the off timer for the unit.

!5 MULTI

Press this button to select a screen mode from among single mode, side by side, and picture in picture.

!6 SELECT

Press this button to select the active picture in a multi screen mode.

!7 AUTO ADJUST

Press this button to adjust Fine Picture, Picture ADJ, Position, and Contrast automatically, or to switch the screen size to ZOOM mode automatically with the superimposed caption displayed fully only when the picture contains dark areas above and below the picture.

!8 Remote control signal transmitter

Transmits the remote control signals.

!9 Remote Jack

Insert the plug of the supplied remote cable here when using the supplied remote control in the wired condition.

Battery Installation and Replacement

Insert the 2 “AAA” batteries, making sure to set them in with the proper polarity.

1.Press and open the cover.

2.Align the batteries according to the (+) and (–) indication inside the case.

3.Replace the cover.

Using the wired remote control mode

Connect the supplied remote cable to the remote control’s remote jack and the “REMOTE CONTROL” terminal on the monitor. When the cable is connected, the mode automatically switches to wired remote control. When the wired remote control mode is used, the remote control can be operated even if no batteries are loaded.

VIDEO 1

CONTROL

VIDEO 2

LOCK

VIDEO 3

)

L ( MONO

ON /OFF

CB/PB

SPEAKERS MUST

HAVE MORE THAN

7WATT RATING

IMPEDANCE 6 OHM

RIGHT LEFT

CR/PR

L ( MONO

AUDIO 2 DVD1/HD1AUDIO 3 AUDIO 1RGB2/DVD2/HD2

RGB 1

R/CR/PR

G/Y

B/CB/PB

L ( MONO

RGB 3

( Digital RGB

CONTROL LOCK

ON /OFF

REMOTE CONTROL

EXTERNAL CONTROL

REMOTE

)

CONTROL

EXTERNAL CONTROL

)

Remote Control Cable

Operating Range

* Use the remote control within a distance of about 5 m/

16ft. from the front of the monitor’s remote control sensor

and at horizontal and vertical angles of up to approximately 30°.

* The remote control operation may not function if the

monitor’s remote control sensor is exposed to direct sunlight or strong artificial light, or if there is an obstacle between the sensor and the remote control.

UME

INPUT SELECT

/EXITLEFT/— RIGHT/+

POWER/STANDBY

Approx. 5m/ 16ft

To Remote Jack

Handling the remote control

• Do not drop or mishandle the remote control.

• Do not get the remote control wet. If the remote control

gets wet, wipe it dry immediately.

• Avoid heat and humidity.

• When not using the remote control for a long period,

remove the batteries.

• Do not use new and old batteries together, or use different types together.

• Do not take apart the batteries, heat them, or throw them into a fire.

• When using the remote control in the wireless condition, be sure to unplug the remote cable from the REMOTE CONTROL terminal on the monitor.

Installation

VIDEO 1

VIDEO 2

VIDEO 3

)

L ( MONO

CB/ PB

CR/ PR

)

L ( MONO

AUDIO 2 DVD1 /HD1AUDIO 3 AUDIO 1RGB2/ DVD2/HD2

RGB 1

R/CR/PR

G/Y

B/CB/PB

)

L ( MONO

RGB 3

(

)

Digital RGB

To video inputs on the plasma monitor

Signal cable (supplied) To Mini D-Sub 15 pin connector on the plasma monitor

VCR or Laser Disc Player

Document Camera

IBM VGA or

Compatibles

Macintosh or Compatibles

(Desk top type)

Monitor adapter for Macintosh

CONTROL LOCK

ON / OFF

REMOTE CONTROL

EXTERNAL CONTROL

An image may not be displayed correctly if a video source like a VCR is connected to the DVD terminals.

Personal computer with a digital RGB output

DVD Player

Connecting Your PC or Macintosh Computer

Connecting your PC or Macintosh computer to your plasma monitor will enable you to display your computer’s screen image for an impressive presentation. The plasma monitor supports the signals described on page 55. To connect a PC, Macintosh or compatible graphics adapter, simply:

1. Turn off the power to your plasma monitor and computer.

2. If your PC does not support SXGA/XGA/SVGA/VGA you will need to install an SXGA/XGA/SVGA/VGA graphics board. Consult your computer’s owner’s manual for your SXGA/XGA/SVGA/VGA configuration. If you need to install a new board, see the manual that comes with your new graphics board for installation instructions.

3. The plasma monitor provides signal compatibility up to VESA 16001200 (UXGA). However, it is not recommended to use this resolution due to image readability on the monitors 1365768 native pixel resolution panel.

Connecting Your Document Camera

You can connect your plasma monitor to a document camera. To do so, simply:

1. Turn off the power to your plasma monitor and document camera.

2. Use a standard video cable to connect your document camera to the Video input on your plasma monitor.

3. Turn on the plasma monitor and the document camera.

Note:

for more information about your camera’s video output requirements.

Refer to your document camera owner’s manual

Connecting Your VCR or Laser Disc Player

Use common RCA cables (not provided) to connect your VCR or laser disc player to your plasma monitor. To make these connections, simply:

4. Use the signal cable that’s supplied to connect your PC or Macintosh computer to the plasma monitor. For Macintosh, use the monitor adapter to connect to your computer’s video port.

5. Turn on the plasma monitor and the computer.

6. If the plasma monitor goes blank after a period of inactivity, it may be caused by a screen saver installed on the computer you’ve connected to the plasma monitor.

When using a Macintosh with the plasma monitor, the following four display standards are supported using the Macintosh adapter :

13" fixed mode 16" fixed mode 19" fixed mode 21" fixed mode

The 19" fixed mode is recommended for the plasma monitor.

Connections with Equipment that has a Digital Interface

Connections can be made with equipment that is equipped with a digital interface compliant with the DVI (Digital Visual Interface) standard. * Use a DVI 29-pin signal cable and the ferrite cores

(supplied) when making connections to the RGB3 IN (DVI) connector of the main unit. Note that the RGB3 IN(DVI) terminal does not support analog RGB input source.

Note:

1. Input TMDS signals conforming to DVI standards. The TMDS input corresponds to 1 link.

2. To maintain display quality, use a cable with a quality

prescribed by DVI standards that is within 5 meters in length.

1. Turn off the power to your plasma monitor and VCR or laser disc player.

2. Connect one end of your RCA cable to the video output connector on the back of your VCR or laser disc player, connect the other end to the Video input on your plasma monitor. Use standard RCA audio patch cords to connect the audio from your VCR or laser disc player to your plasma monitor (if your VCR or laser disc player has this capability). Be careful to keep your right and left channel connections correct for stereo sound.

3. Turn on the plasma monitor and the VCR or laser disc player.

Note:

manual for more information about your equipment’s video output requirements.

Refer to your VCR or laser disc player owner’s

Connecting Your DVD Player

You can connect your plasma monitor to a DVD player. To do so, simply:

1. Turn off the power to your plasma monitor and DVD player.

2. Use a standard video cable to connect your DVD player to the Y, Cb, and Cr inputs on your plasma monitor. Or use the DVD-player’s S-Video output. Use a standard S-Video cable to connect to the S-Video input on the plasma monitor.

3. Turn on the plasma monitor and the DVD player.

External Speaker Connections

RIGHT LEFT

AC-IN

SPEAKERS MUST

HAVE MORE THAN

7WATT RATING

IMPEDANCE 6 OHM

RIGHT LEFT

VIDEO 1

VIDEO 2

VIDEO 3

)

L ( MONO

CB/PB

CR/PR

)

L ( MONO

AUDIO 2 DVD1/HD1AUDIO 3 AUDIO 1RGB2/DVD2/HD2

RGB 1

R/CR/PR

G/Y

B/CB/PB

)

L ( MONO

RGB 3

(

)

Digital RGB

CONTROL LOCK

ON /OFF

REMOTE CONTROL

EXTERNAL CONTROL

External speakers (option) may be connected to the plasma monitor to reproduce sound from VIDEO, DVD or RGB signal sources.

External speakers may be connected directly to the SPEAKERS terminals or indirectly by connecting a stereo system amplifier to the audio outputs.

CAUTION:

Unplug the plasma monitor and all connected components before connecting external speakers. Use only speakers with 6-ohm impedance and a power input rating of 7 watts or more.

To connect external speakers directly to the plasma monitor:

1. Strip the ends of the speaker wires.

2. Press down the tabs below the SPEAKERS terminals, insert the speaker wire and release the tab to secure the speaker wire connection:

[a] Connect the right speaker (located at right side

of the monitor when viewed from the front) positive (+) wire to RIGHT +.

[b] Connect the right speaker negative (–) wire to

RIGHT –.

[c] Connect the left speaker negative (–) wire to

LEFT–.

[d] Connect the left speaker positive (+) wire to

LEFT+.

Pin Assignments and Signal Levels for 15 pin RGB (Analog)

5 4 3 2 1

10 9 8 7 6

15 14 13 12 11

Pin No.

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15

Red Green or sync-on-green Blue No connection Ground Red ground Green ground Blue ground No connection Sync signal ground No connection Bi-directional DATA (SDA) Horizontal sync or Composite sync Vertical sync Data clock

Signal (Analog)

Pin Configuration and Signal of the RGB 3 IN Connector (DVI Connector)

The unit is equipped with a type of connector commonly used for both analog and digital. (Functionally, this cannot be used for an analog input.) (TMDS can be used for one link only.)

RGB 3

8 25 26

27 28

Pin No.

9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29

Signal (Digital)

T.M.D.S Data 2 T.M.D.S Data 2 + T.M.D.S Data 2 Shield No connection No connection DDC Clock DDC Data No connection T.M.D.S Data 1 T.M.D.S Data 1 + T.M.D.S Data 1 Shield No connection No connection +5V Power Ground Hot Plug Detect T.M.D.S Data 0 T.M.D.S Data 0 + T.M.D.S Data 0 Shield No connection No connection T.M.D.S Clock Shield T.M.D.S Clock + T.M.D.S Clock No connection No connection No connection No connection No connection

Basic Operations

POWER

To turn the unit ON and OFF:

1. Plug the power cord into an active AC power outlet.

2. Press the POWER ON button (on the remote control) to turn on the unit.

The monitor’s POWER/STANDBY indicator will light up (green) when the unit is on.

3. Press the POWER OFF button (on the remote control or the unit) to turn off the unit.

The monitor’s POWER/STANDBY indicator turns red and the standby mode is set (only when turning off the unit with the remote control).

VOLUME

To adjust the volume:

1. Press and hold the VOLUME button (on the remote control or the unit) to increase to the desired level.

2. Press and hold the VOLUME control or the unit) to decrease to the desired level.

button (on the remote

MUTE

To cancel the sound:

Press the MUTE button on the remote control to cancel the sound; press again to restore.

DISPLAY

To check the settings:

1. The screen changes each time the DISPLAY button is pressed.

2. If the button is not pressed for approximately three seconds, the menu turns off.

DIGITAL ZOOM

Digital zoom specifies the picture position and enlarges the picture.

1. Press the POINTER button to display the pointer. (

To change the size of the picture:

Press the ZOOM+ button and enlarge the picture. The pointer will change to resemble a magnifying glass. ( A press of the ZOOM- button will reduce the picture and return it to its original size.

To change the picture position:

Select the position with the ▲▼

2. Press the POINTER button to delete the pointer.

)

 

buttons.

AUTO ADJUST

To adjust the size or quality of the picture automatically:

Press the AUTO ADJUST button.

Information

 AUTO ADJUST ON setting

When RGB (still picture) input

is selected ...... Fine Picture, Picture ADJ, Position,

and Contrast will be adjusted automatically.

When RGB (motion picture), VIDEO, or Y/Pb/Pr (component) input

is selected ...... The screen size switches to ZOOM

mode automatically with the superimposed caption displayed fully only when the picture contains dark areas above and below the picture.

)

OFF TIMER

To set the off timer:

The off timer can be set to turn the power off after 30, 60, 90 or 120 minutes.

To cancel the off timer:

1. Press the OFF TIMER button twice in a row.

2. The off timer is canceled.

1. Press the OFF TIMER button to start the timer at 30 minutes.

2. Press the OFF TIMER button to the desired time.

3. The timer starts when the menu turns off.

→ 30 → 60 → 90 → 120 → 0

OFF TIMER 30

To check the remaining time:

1. Once the off timer has been set, press the OFF TIMER button once.

2. The remaining time is displayed, then turns off after a few seconds.

OFF TIMER 0

Note:

After the power is turned off with the off timer ... A slight current is still supplied to the monitor. When you are leaving the room or do not plan to use the system for a long period of time, turn off the power of the monitor.

3. When five minutes remain the remaining time appears until it reaches zero.

OFF TIMER 28

WIDE Operations

Watching with a wide screen

With this function, you can select one of four screen sizes.

When watching videos or digital video discs

1. Press the WIDE button on the remote control.

2. Within 3 seconds ... Press the WIDE button again. The screen size switches as follows:

→ ZOOM → NORMAL → FULL → STADIUM

ZOOM size screen

The picture is expanded in the horizontal and vertical direction, maintaining the original proportions. * Use this for theater size (wide) movies, etc.

(manual)

STADIUM size screen

The picture is expanded in the horizontal and vertical directions at different ratios. * Use this for watching normal video programs (4:3) with a

wide screen.

When watching high definition video source

1. Press the WIDE button on the remote control.

FULL size screen (16 : 9)

NORMAL size screen (4:3)

The normal size screen is displayed. * The picture has the same size as video pictures with a

4 : 3 aspect ratio.

FULL size screen

The image is expanded in the horizontal direction. * Images compressed in the horizontal direction (“squeezed

images”) are expanded in the horizontal direction and displayed on the entire screen. (Normal images are expanded in the horizontal direction.)

The full size screen is displayed. * The picture has the same size as video pictures (16 : 9).

Watching computer images with a wide screen

Switch to the wide screen mode to expand the 4 : 3 image to fill the entire screen.

1.Press the WIDE button on the remote control.

2.Within 3 seconds ...

Press the WIDE button again. The screen size switches as follows:

→ NORMAL → FULL

FULL size screen

The image is expanded in the horizontal and vertical direction.

NORMAL size screen (4:3 or SXGA 5:4)

The picture has the same size as the normal computer image.

FULL size screen

The image is expanded in the horizontal direction.

When wide signals are input.

FULL size screen

When wide signals are input.

TRUE

The image is true resolution.

FULL

Information

 Supported resolution

See page 55 for details on the display output of the various VESA signal standards supported by the monitor.

When “PICTURE SIZE” is set to “OFF”

The screen size switches as follows:

→ TRUE → FULL

TRUE size screen (VGA, SVGA 4:3)

The image is true resolution.

 “PICTURE SIZE” setting

When the setting of “PICTURE SIZE” is OFF, the size of RGB-input pictures will be TRUE in place of NORMAL.

 When 852 (848) dot  480 line wide VGA* signals with a vertical frequency of 60 Hz and horizontal frequency of 31.7 (31.0) kHz are input

Select an appropriate setting for RGB SELECT mode referring to the“Table of Signals Supported” on page

55. * “ IBM PC/AT” and “VGA” are registered trademarks

of IBM, Inc. of the United States.

MULTI SCREEN Operations

VIDEO1 RGB/PC1

VIDEO1RGB/PC1

VIDEO1 RGB/PC1

Showing a couple of pictures on the screen at the same time

* An RGB-input picture may not be displayed in these modes,

depending on the input signal specifications.

1. Press the MULTI button to select a screen mode from among single mode, side by side, and picture in picture.

Side by side

VIDEO1 RGB/PC1

Note:

Picture A and B on the above screen are not always of the same height.

Picture in picture

Operations in the Side-by-side mode

To change the picture size, press the cursor  or  button.



button



button

VIDEO1 RGB/PC1



button

VIDEO1

Sub

screen

RGB/PC1

Main screen

Information

Multi screen operations may not function depending on the combination of input signals. In the table below, “” means Yes, “” means No.

Pictures displayed on the right/main screen

VIDEO2

VIDEO3





HD/DVD1

















HD/DVD2











RGB/PC1





RGB/PC2





RGB/PC3





Pictures

displayed on

the left/sub

screen

VIDEO1

VIDEO2

VIDEO3

HD/DVD1

HD/DVD2

RGB/PC1

RGB/PC2

RGB/PC3

VIDEO1





 Multi screen operations may not function

depending on the type of the RGB signals.

To swap the picture on the right and the left, press the



cursor

button.



button

To make the desired picture active, press the SELECT button.

SELECT button

Operations in the Picture-in-picture mode

To move the position of the sub screen, press the cursor or  button.

Selecting the input signals to be displayed



1. Press the SELECT button to make the desired picture active.

VIDEO1 RGB/PC1



button

VIDEO1 RGB/PC1



button

To change the size of the sub screen, press the ZOOM /button.

VIDEO1 RGB/PC1

ZOOM— button

ZOOM+ button

VIDEO1 RGB/PC1

ZOOM— button

ZOOM+ button

ZOOM— button

VIDEO1 RGB/PC1

ZOOM+ button

VIDEO1 RGB/PC1

2. Press the RGB/PC, VIDEO, or DVD/HD button. Each press of the button changes the selection of the input signal. The INPUT SELECT button on the monitor can also be used to change the selection.

Adjusting the OSM controls

1. Press the SELECT button to make the desired picture active.

2. Press the PROCEED button to display the MAIN MENU.

3. Adjust the setting to your preference. For details, see “OSM (On Screen Menu) Controls” on page 18.

Note:

• During Multi screen mode, Auto Adjust does not affect the screen.

• During Multi screen mode, some functions of OSM controls are not available.

To make the desired picture active, press the SELECT button.

VIDEO1 RGB/PC1

SELECT button

VIDEO1 RGB/PC1

+ 108 hidden pages

Toshiba 50HP82, 50HP82SVM, 50HP82S, 50XP26 Schematic

CONTENTS

SAFETY PRECAUTIONS

OWNER'S MANUAL

Important Information

Contents

Installation

Basic Operations

WIDE Operations

MULTI SCREEN Operations