Toshiba 5005 User Manual

Download

Satellite® 5005 Series User’s Guide

If you need assistance:

❖ VirtualTech

http://virtualtech.toshiba.com

❖ InTouch

Calling within the United States (800) 457-7777 Calling from outside the United States (949) 859-4273

For more information, see Chapter 9 on page 209 in this guide.

Center

TOSHIBA

C6604-1101M2

Model: Satellite® 5005 Series

Compact Disk-ReWritable

The computer system you purchased may include a Compact DiskReWritable (CD-RW), one of the most advanced storage technologies available. As with any new technology, you must read and follow all set-up and usage instructions in the applicable user guides and/or manuals enclosed. If you fail to do so, this product may not function properly and you may lose data or suffer other damage. TOSHIBA AMERICA

INFORMATION SYSTEMS (“TOSHIBA”), ITS AFFILIATES AND SUPPLIERS DO NOT WARRANT THAT OPERATION OF THE PRODUCT WILL BE UNINTERRUPTED OR ERROR FREE. YOU AGREE THAT TOSHIBA, ITS AFFILIATES AND SUPPLIERS SHALL HAVE NO RESPONSIBILITY FOR DAMAGE TO OR LOSS OF ANY BUSINESS, PROFITS, PROGRAMS, DATA OR REMOVABLE STORAGE MEDIA ARISING OUT OF OR RESULTING FROM THE USE OF THE PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY THEREOF.

Protection of Stored Data

For your important data, please make periodic back-up copies of all the data stored on the hard disk or other storage devices as a precaution against possible failures, alteration, or loss of the data. IF YOUR DATA IS

ALTERED OR LOST DUE TO ANY TROUBLE, FAILURE OR MALFUNCTION OF THE HARD DISK DRIVE OR OTHER STORAGE DEVICES AND THE DATA CANNOT BE RECOVERED, TOSHIBA SHALL NOT BE LIABLE FOR ANY DAMAGE OR LOSS OF DATA, OR ANY OTHER DAMAGE RESULTING THEREFROM. WHEN COPYING OR TRANSFERRING YOUR DATA, PLEASE BE SURE TO CONFIRM WHETHER THE DATA HAS BEEN SUCCESSFULLY COPIED OR TRANSFERRED. TOSHIBA DISCLAIMS ANY LIABILITY FOR THE FAILURE TO COPY OR TRANSFER THE DATA CORRECTLY.

Critical Applications

The computer you have purchased is not designed for any “critical applications.” “Critical applications” means life support systems, medical applications, connections to implanted medical devices, commercial transportation, nuclear facilities or systems or any other applications where product failure could lead to injury to persons or loss of life or catastrophic property damage. ACCORDINGLY, TOSHIBA, ITS AFFILIATES

AND SUPPLIERS DISCLAIM ANY AND ALL LIABILITY ARISING OUT OF THE USE OF THE COMPUTER PRODUCTS IN

ANY CRITICAL APPLICATIONS. IF YOU USE THE COMPUTER PRODUCTS IN A CRITICAL APPLICATION, YOU, AND NOT TOSHIBA, ASSUME FULL RESPONSIBILITY FOR SUCH USE.

FCC Notice

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

❖ Reorient or relocate the receiving antenna.

❖ Increase the separation between the equipment and receiver.

❖ Connect the equipment to an outlet on a circuit different from that to

which the receiver is connected.

❖ Consult the dealer or an experienced radio/TV technician for help.

NOTE: Only peripherals complying with the FCC Class B limits may be attached

to this computer. Operation with non-compliant peripherals or peripherals not recommended by Toshiba is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer's video jack, USB ports and microphone jack. Changes or modifications made to this equipment not expressly approved by Toshiba or

parties authorized by Toshiba could void the user equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

❖ This device may not cause harmful interference.

❖ This device must accept any interference received, including

interference that may cause undesired operation.

’s authority to operate the

Contact:

Toshiba America Information Systems, Inc.

9740 Irvine Blvd. Irvine, CA 92618-1697 (949) 583-3000

Industry Canada Requirement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conformé à la norme NMB-003 du Canada.

FCC Requirements

The following information is pursuant to FCC CFR 47, Part 68 and refers to internal modems.

Installation

When you are ready to install or use the modem, call your local telephone company and give them the following information:

❖ The telephone number of the line to which you will connect the

modem.

❖ The FCC registration number of the modem.

❖ The ringer equivalence number (REN) of the modem, which is 0.6B.

The modem connects to the telephone line by means of a standard jack called the USOC RJ11C.

Type of Service

Your modem is designed to be used on standard-device telephone lines. Connection to telephone company-provided coin service (central office implemented systems) is prohibited. Connection to party lines service is subject to State tariffs. If you have any questions about your telephone line, such as how many pieces of equipment you can connect to it, the telephone company will provide this information upon request.

Telephone Company Procedures

The goal of the telephone company is to provide you with the best service it can. In order to do this, it may occasionally be necessary for them to make changes in their equipment, operations or procedures. If these changes might affect your service or the operation of your equipment, the telephone

company will give you notice, in writing, to allow you to make any changes necessary to maintain uninterrupted service.

If Problems Arise

If any of your telephone equipment is not operating properly, you should immediately remove it from your telephone line, as it may cause harm to the telephone network. If the telephone company notes a problem, they may temporarily discontinue service. When practical, they will notify you in advance of this disconnection. If advance notice is not feasible, you will be notified as soon as possible. When you are notified, you will be given the opportunity to correct the problem and informed of your right to file a complaint with the FCC. In the event repairs are ever needed on your modem, they should be performed by Toshiba Corporation, Toshiba America Information Systems, Inc. or an authorized representative of Tos hi ba .

Disconnection

If you should ever decide to permanently disconnect your modem from its present line, please call the telephone company and let them know of this change.

Fax Branding

The Telephone Consumer Protection Act of 1991 makes it unlawful to use a computer or other electronic device to send any message via a telephone fax machine unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business, other entity or individual sending the message and the telephone number of the sending machine or such business, other entity or individual.

In order to program this information into your fax modem, you should complete the setup for your fax software before sending a message.

Instructions for IC CS-03 certified equipment

1 NOTICE: The Industry Canada label identifies certified equipment.

This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer should be

aware that compliance with the above conditions may not prevent degradation of service in some situations.

Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.

Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.

2 The user manual of analog equipment must contain the equipment’s

Ringer Equivalence Number (REN) and an explanation notice similar to the following:

The Ringer Equivalence Number (REN) of this device can be found on the label affixed to your computer.

NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.

3 The standard connecting arrangement (telephone jack type) for this

equipment is jack type(s): USOC RJ11C.

Wireless Interoperability

The Toshiba Wireless LAN Mini PCI Card products are designed to be interoperable with any wireless LAN product that is based on Direct Sequence Spread Spectrum (DSSS) radio technology, and is compliant to:

❖ The IEEE 802.11 Standard on Wireless LANs (Revision B), as

defined and approved by the Institute of Electrical and Electronics Engineers.

❖ The Wireless Fidelity (Wi-Fi

Wireless Ethernet Compatibility Alliance.

) certification as defined by the WECA

Wireless LAN and your Health

Wireless LAN products, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitted by Wireless LAN devices however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones. Because Wireless LAN products operate within the guidelines found in radio frequency safety standards and recommendations, Toshiba believes Wireless LAN is safe for use by consumers. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.

In some situations or environments, the use of Wireless LAN may be restricted by the proprietor of the building or responsible representatives of the organization. These situations may for example include:

❖ Using the Wireless LAN equipment on board of airplanes, or

❖ In any other environment where the risk of interference to other

devices or services is perceived or identified as harmful.

If you are uncertain of the policy that applies on the use of wireless devices in a specific organization or environment (e.g., airports), you are encouraged to ask for authorization to use the Wireless LAN device prior to turning on the equipment.

Regulatory Information

The Toshiba Wireless LAN Mini PCI Card must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product. This device complies with the following radio frequency and safety standards.

Canada – Industry Canada (IC)

This device complies with RSS 210 of Industry Canada.

Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device.

USA-Federal Communications Commission (FCC)

This device complies with Part 15 of FCC Rules. Operation of the devices in a Wireless LAN System is subject to the following two conditions:

❖ This device may not cause harmful interference.

❖ This device must accept any interference that may cause undesired

operation.

Caution: Exposure to Radio Frequency Radiation

The radiated output power of the Toshiba Wireless LAN Mini PCI Card is far below the FCC radio frequency exposure limits. Nevertheless, the Toshiba Wireless LAN Mini PCI Card shall be used in such a manner that the potential for human contact during normal operation is minimized. When using this device in combination with Wireless LAN Outdoor Antenna products, a certain separation distance between antenna and nearby persons has to be kept to ensure RF exposure compliance. The distance between the antennas and the user should not be less than 20.0 cm.

Refer to the Regulatory Statements as identified in the documentation that comes with those products for additional information.

The Toshiba Wireless LAN Mini PCI Card is far below the FCC radio frequency exposure limits.

Nevertheless, it is advised to use the Toshiba Wireless LAN Mini PCI Card in such a manner that human contact during normal operation is minimized.

Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

❖ Reorient or relocate the receiving antenna.

❖ Increase the distance between the equipment and the receiver.

❖ Connect the equipment to an outlet on a circuit different from that to

which the receiver is connected.

❖ Consult the dealer or an experienced radio/TV technician for help.

Toshiba is not responsible for any radio or television interference caused by unauthorized modification of the devices included with this Toshiba Wireless LAN Mini PCI Card, or the substitution or attachment of connecting cables and equipment other than specified by Toshiba.

The correction of interference caused by such unauthorized modification, substitution or attachment will be the responsibility of the user.

Approved Countries for use

This equipment is approved to the radio standard by the countries in Fig.1.

Australia Austria Belgium

Canada Denmark Finland

France Germany Greece

Iceland Ireland Italy

Japan Luxembourg Mexico

Netherlands New Zealand Norway

Poland Portugal Spain

Sweden Switzerland UK

USA

CD-ROM, DVD-ROM, and DVD-ROM/CD-RW Safety Instructions

The CD-ROM, DVD-ROM, and DVD-ROM/CD-RW drives employ a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.

Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure.

To prevent direct exposure to the laser beam, do not try to open the enclosure.

Location of the required label

(Sample shown below. (Location of the label and manufacturing information may vary.)

CAU TION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep it for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” To prevent direct exposure to the laser beam, do not try to open the enclosure.

Use of controls or adjustments or performance of procedures other than those specified in the owner’s manual may result in hazardous radiation exposure.

This guide is copyrighted by Toshiba America Information Systems, Inc. with all rights reserved. Under the copyright laws, this guide cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed, however, with respect to the use of the information contained herein.

Export Administration Regulation

This document contains technical data that may be controlled under the U.S. Export Administration Regulations, and may be subject to the approval of the U.S. Department of Commerce prior to export. Any export, directly or indirectly, in contravention of the U.S. Export Administration Regulations is prohibited.

Notice

The information contained in this manual, including but not limited to any product specifications, is subject to change without notice.

TOSHIBA CORPORATION AND TOSHIBA AMERICA INFORMATION SYSTEMS, INC. (TOSHIBA) PROVIDES NO WARRANTY WITH REGARD TO THIS MANUAL OR ANY OTHER INFORMATION CONTAINED HEREIN AND HEREBY EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE WITH REGARD TO ANY OF THE FOREGOING. TOSHIBA ASSUMES NO LIABILITY FOR ANY DAMAGES INCURRED DIRECTLY OR INDIRECTLY FROM ANY TECHNICAL OR TYPOGRAPHICAL ERRORS OR OMISSIONS CONTAINED HEREIN OR FOR DISCREPANCIES BETWEEN THE PRODUCT AND THE MANUAL. IN NO EVENT SHALL TOSHIBA BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL, OR EXEMPLARY DAMAGES, WHETHER BASED ON TORT, CONTRACT OR OTHERWISE, ARISING OUT OF OR IN CONNECTION WITH THIS MANUAL OR ANY OTHER INFORMATION CONTAINED HEREIN OR THE USE THEREOF.

Trademarks

Satellite, Noteworthy, SelectServ, InTouch, and Fn-Esse are registered trademarks, VirtualTech, SecureSleep, and FreedomWare are trademarks of Toshiba America Information Systems, Inc. and/or Toshiba Corporation.

WinDVD is a trademark of InterVideo, Inc.

Microsoft, Windows, DirectX, and DirectShow are registered trademarks, and Windows Media is a trademark of Microsoft Corporation.

Dolby is a registered trademark of Dolby Laboratories.

i.LINK is a registered trademark of the Sony Corporation.

SPANworks 2000 is a trademark of SPANworks, U.S.A.

Wi-Fi is a trademark of the Wireless Capability Ethernet Alliance.

Bluetooth is a trademark owned by its proprietor and used by Toshiba under license.

TouchPad is a trademark of Synaptics, Inc.

CompuServe is a registered trademark of America Online, Inc.

All other brand and product names are trademarks or registered trademarks of their respective companies.

Computer Disposal Information

This product contains mercury. Disposal of this material may be regulated due to environmental considerations. For disposal, reuse or recycling information, please contact your local government or the Electronic Industries Alliance at www.eiae.org.

Introduction ..............................................................23

This guide .............................................................. 23

Safety icons ........................................................... 24

Other icons used.............................................. 25

Other documentation ............................................. 25

Service options ...................................................... 26

Chapter 1: Finding Your Way Around ........................ 27

Making sure you have everything .......................... 27

Front with the display closed ................................. 28

Back....................................................................... 29

Right side............................................................... 30

Left side ................................................................. 31

Front with the display open.................................... 33

Keyboard indicator panel ................................. 35

System indicator panel .................................... 36

CD/DVD control buttons .................................. 37

Underside .............................................................. 38

Chapter 2: Getting Started......................................... 40

Selecting a place to work ....................................... 40

Contents

Creating a computer-friendly environment....... 40

Keeping yourself comfortable .......................... 41

Precautions...................................................... 44

Setting up your computer ...................................... 45

Installing additional memory (optional) ........... 46

Connecting a mouse .............................................. 50

Connecting a printer .............................................. 50

Using external display devices ............................... 51

Directing the display output when you turn on

the computer .................................................. 51

Adjusting the quality of the external display..... 52

Display limitations ........................................... 52

Connecting an external diskette drive..................... 53

Using an external keyboard.................................... 53

Connecting the AC adapter..................................... 53

Charging the battery .............................................. 55

Using the computer for the first time..................... 56

Opening the display panel ................................ 56

Turning on the power ....................................... 56

Activating the power-on password................... 58

Using the TouchPad ......................................... 59

Setting up your software.................................. 60

Setting up a printer .......................................... 61

Setting up the fax function..................................... 63

Turning off the computer ....................................... 64

Caring for your computer....................................... 65

Cleaning the computer ..................................... 65

Moving the computer....................................... 65

Using a computer lock ..................................... 66

Chapter 3: Learning the Basics ................................. 67

Computing tips ...................................................... 67

Using the keyboard ................................................ 68

Character keys ................................................. 69

Contents

Ctrl, Fn, and Alt keys ........................................ 69

Function keys................................................... 69

Windows® special keys ................................... 70

Overlay keys..................................................... 70

Emulating a full-size keyboard ............................... 72

TOSHIBA Console button....................................... 72

Starting a program................................................. 73

Saving your work ................................................... 73

Printing your work ................................................. 74

Using diskettes ...................................................... 75

Inserting and removing diskettes..................... 76

Caring for diskettes.......................................... 76

Backing up your files ............................................. 77

Copying to a diskette ....................................... 77

Playing a CD or DVD .............................................. 78

Drive components and control buttons............ 78

CD/DVD control buttons .................................. 80

CD/DVD control and Digital audio control ........ 81

Inserting a disc ................................................ 83

Playing an audio CD......................................... 85

Playing a DVD .................................................. 86

Viewing the contents of a CD or DVD............... 87

Removing a disc with the computer on............ 87

Removing a disc with the computer off ........... 88

Caring for CDs and DVDs................................. 88

Using the DVD-ROM or DVD-ROM/CD-RW

multifunction drive........................................... 89

Setting up for communications.............................. 89

Connecting the modem.................................... 90

Connecting your computer to a network .......... 90

Powering down the computer................................ 91

Turn Off command........................................... 91

Hibernation command ..................................... 91

Stand By command.......................................... 92

Contents

Using Turn Off........................................................ 93

Shutting down more quickly ............................ 94

Starting again after Turn Off............................. 95

Using Hibernation .................................................. 95

Going into Hibernation mode more quickly...... 96

Starting again from Hibernation mode ............. 97

Using Stand By ...................................................... 97

Going into Stand By mode more quickly.......... 98

Starting again from Stand By........................... 99

Chapter 4: Mobile Computing ................................. 100

Toshiba’s energy-saver design ............................. 100

Running the computer on battery power ............. 100

Using additional batteries .............................. 101

Battery safety precautions.............................. 101

Maximizing battery life ................................... 102

Charging batteries................................................ 103

Charging the main battery.............................. 103

Charging the RTC battery............................... 104

Monitoring battery power .................................... 105

Determining remaining battery power............ 105

Conserving battery power .............................. 106

What to do when the battery runs low ........... 107

Setting battery alarms.................................... 107

Changing the main battery ................................... 108

Removing the battery from the computer ...... 108

Removing the battery from the battery cover. 110

Inserting a charged battery ............................ 110

Disposing of used batteries safely ....................... 111

Traveling tips........................................................ 112

Chapter 5: Toshiba Utilities ..................................... 113

TOSHIBA Accessibility ......................................... 113

Contents

Fn-esse ................................................................ 114

Starting Fn-esse............................................. 115

Assigning a key to a program or document ... 116

Viewing existing key assignments ................. 118

Changing or removing existing key

assignments ................................................. 118

Hotkey utility ........................................................ 118

TOSHIBA Console ................................................ 119

Customize Your Computer ............................. 120

Network ......................................................... 121

Security.......................................................... 121

TOSHIBA Button Controls.............................. 121

Power Management ....................................... 124

Toshiba Hardware Setup ................................ 127

Chapter 6: Getting to Know the Windows® XP Operating

System ............................................... 129

Lesson 1: Exploring the desktop.......................... 129

Finding your way around the desktop ............ 130

Windows®XP file system............................... 132

Lesson 2: Using the TouchPad and control buttons

together ......................................................... 133

Lesson 3: Learning about the Internet ................. 137

Lesson 4: Creating a new document .................... 138

Lesson 5: Creating a new folder........................... 139

Lesson 6: Starting programs ............................... 140

Lesson 7: Resizing, repositioning, and hiding

windows ........................................................ 142

Using the taskbar ........................................... 143

Minimizing and maximizing windows ............ 144

Resizing and moving windows....................... 144

Lesson 8: Closing programs ................................ 145

Lesson 9: Creating shortcuts ............................... 146

Creating a shortcut to the Calculator.............. 146

Contents

Creating a shortcut to the Character Map ...... 147

Lesson 10: Changing the screen saver................. 150

Lesson 11: Setting the date and time................... 152

Lesson 12: Removing objects from the desktop .. 153

Lesson 13: Using System Restore ....................... 155

Lesson 14: If I am lost, what do I do? ................. 156

Windows® XP Help and Support ................... 156

Using the Windows® XP tour ........................ 158

Lesson 15: Turning off your computer ................. 159

Chapter 7: Exploring Your Options.......................... 160

Windows® XP special features............................. 160

Personalizing your desktop.................................. 161

Customizing the taskbar ................................ 161

Changing desktop and browsing style ........... 162

Personalizing individual windows .................. 163

Customizing window toolbars........................ 163

Displaying information about each folder....... 165

Using your computer at the office........................ 167

Exchanging data with another computer.............. 167

Setting up for communications...................... 167

Connecting the modem to a telephone line .... 169

Connecting your computer to a network ....... 169

Setting up a wireless connection ................... 170

Accessing the wireless modules using your

system tray .............................................. 170

Using Bluetooth ............................................. 171

Using SPANworksTM 2000.............................. 172

Setting up a direct cable connection .............. 172

An overview of using the Internet ........................ 173

The Internet ................................................... 173

The World Wide Web ..................................... 173

Internet Service Providers.............................. 174

Connecting to the Internet ............................. 174

Contents

Surfing the Internet........................................ 175

Internet features............................................. 175

Uploading and downloading files from the

Internet ......................................................... 176

Toshiba’s online resources................................... 176

Exploring video features ...................................... 176

Viewing presentations or DVD movies on your

television.................................................. 176

Transferring and editing video data................ 178

Playing DVDs ................................................. 178

Exploring audio features ...................................... 179

Recording sounds.......................................... 179

Using a microphone....................................... 179

Adjusting recording quality ............................ 180

Using external speakers or headphones......... 181

Using PC Cards.................................................... 182

PC Card supporting software ......................... 182

Inserting PC Cards......................................... 183

Removing PC Cards....................................... 184

Hot swapping................................................. 184

Using SmartMedia cards...................................... 185

Inserting a SmartMedia card.......................... 185

Removing a SmartMedia card........................ 186

Using Secure Digital cards................................... 186

Inserting a Secure Digital card ....................... 187

Removing a Secure Digital card ..................... 187

Chapter 8: WinDVD 2000 ........................................ 188

Playing DVDs ....................................................... 188

Using the WinDVD toolbar ............................. 190

Using the WinDVD status bar ........................ 190

Using the WinDVD control panel.................... 191

Using the control panel playback buttons ...... 192

Maximizing the video window........................ 194

Contents

Using playlists ..................................................... 195

Creating playlists ........................................... 195

Loading and playing playlists......................... 196

Resuming normal playback after using

playlists.......................................................... 196

Customizing WinDVD........................................... 197

Setting general properties.............................. 197

Setting audio properties................................. 199

Setting display properties .............................. 200

Customizing the control panel ....................... 200

Using WinDVD advanced features........................ 201

Zooming in..................................................... 206

Panning.......................................................... 207

Zooming out .................................................. 207

Adjusting the color balance............................ 207

Launching an Internet browser from WinDVD ..... 208

Getting help ......................................................... 208

Exiting WinDVD ................................................... 208

Chapter 9: If Something Goes Wrong ..................... 209

Problems that are easy to fix ............................... 209

Problems when you turn on the computer........... 211

The Windows

Using Startup options to fix problems ........... 213

Internet problems .......................................... 214

The Windows® XP operating system can

help you ......................................................... 214

Resolving a hardware conflict .............................. 215

A plan of action.............................................. 215

Resolving hardware conflicts on your own .... 215

Fixing a problem with Device Manager .......... 217

Memory card problems.................................. 218

Power and the batteries ................................. 219

Keyboard problems........................................ 220

operating system is not working. 212

Contents

Display problems ........................................... 221

Disk drive problems ....................................... 223

DVD-ROM or DVD-ROM/CD-RW drive

problems........................................................ 225

Sound system problems ................................ 233

PC Card problems.......................................... 233

Printer problems ............................................ 236

Modem problems........................................... 237

Develop good computing habits .......................... 238

If you need further assistance.............................. 239

Before you call ............................................... 239

Contacting Toshiba ........................................ 239

Other Toshiba Internet Web sites ........................ 241

Appendix A: Hot Keys.............................................. 245

Volume Mute........................................................ 245

Instant password security.................................... 246

Without a password ....................................... 246

With a password ............................................ 246

Power usage mode ............................................. 247

Stand By mode .................................................... 248

Hibernation mode ............................................... 249

Display modes ..................................................... 250

Display brightness ............................................... 251

Enabling a wireless device ................................... 251

Keyboard hot keys .............................................. 252

Appendix B: Power Cable Connectors ..................... 253

USA and Canada ............................................ 253

United Kingdom ............................................. 253

Australia......................................................... 253

Europe ........................................................... 253

Appendix C: Video Modes ....................................... 254

Your computer’s video modes ............................. 255

Glossary ..................................................................257

Contents

Index ....................................................................... 273

Introduction

Welcome to the world of powerful and portable multimedia computers! With your new Toshiba notebook computer, your access to information can accompany you wherever you go.

Your system comes with either the Microsoft Home operating system or the Microsoft Professional operating system. This guide contains information on both operating systems and how they function with your Toshiba computer. For specific information on the software, see the Microsoft booklet that shipped with the computer.

This guide

This guide introduces the computer’s features. You can:

❖ Read the entire guide from beginning to end.

❖ Skim through and stop when a topic interests you.

❖ Use the table of contents and the index to find specific

information.

Windows® XP

Introduction

Safety icons

If you are new to computers, or have not used a notebook computer before, read the first couple of chapters to familiarize yourself with the components of the computer and how to turn it on. After that, seek out whatever interests you most.

Safety icons

This manual contains safety instructions that must be observed in order to avoid potential hazards that could result in personal injuries, damage to your equipment, or loss of data. These safety cautions have been classified according to the seriousness of the risk, and the icons highlight these instructions as follows:

DANGER: This icon indicates the existence of a hazard that could result in death or serious bodily injury if the safety instruction is not observed.

WARNING: This icon indicates the existence of a hazard that could result in bodily injury if the safety instruction is not observed.

CAUTION: This icon indicates the existence of a hazard that could result in damage to equipment or property if the safety instruction is not observed.

NOTE: This icon indicates information that relates to the safe operation of the equipment or related items.

Other icons used

Additional icons highlight other helpful or educational information:

TECHNICAL NOTE: This icon highlights technical information about the computer.

HINT: This icon denotes helpful hints and tips.

DEFINITION: This icon indicates the definition of a term used in the text.

Introduction

Service options

Toshiba offers a full line of service options built around its SelectServ Toshiba’s Web site at Toshiba.com.

If you have a problem or need to contact Toshiba, see “If

Something Goes Wrong” on page 209.

warranty programs. For more information, visit

Chapter 1

Finding Your Way Around

This chapter presents a “grand tour” of your notebook computer. It serves as a reference when you need to locate specific parts of the computer.

Making sure you have everything

Before doing anything else, consult the Quick Start card provided with your system to make sure you received everything. If any items are missing or damaged, notify your dealer immediately. For additional help, see “If you need

further assistance” on page 239.

Finding Your Way Around

Front with the display closed

Optional wireless antenna on-off switch

On those systems with Wi-FiTM and/or BluetoothTM, the wireless antenna on-off switch turns the computer’s wireless antenna on or off.

The infrared port allows cable-free communication with another device, such as a computer or printer, that has a compatible infrared port.

The display latch keeps the display panel closed and locked. To open the display panel, slide the display latch to the right and raise the panel.

Infrared port

Display latch

Back

DC-IN jack

Finding Your Way Around

Back

USB ports

Cooling

vents

Video line

/audio

out

jack

Audio in jack

LAN port

Modem port

i.LINK port

The USB (Universal Serial Bus) ports allow you to connect USB peripherals to your computer.

DEFINITION: USB is a peripheral expansion standard that supports a data-transfer rate of up to 12 Mbps for peripherals such as keyboards, pointing devices, and monitors. USB peripherals have a single standard for cabling and connectors. The USB standard allows hot swapping of peripherals.

The audio in jack allows you to play or record sounds when the computer is hooked up to an external audio source.

The 3.5 mm video/audio line out jack allows you to play DVD audio and video on a projector or TV that accepts audio/video inputs.

The DC-IN jack is where you plug in the AC adapter.

The i.LINK

port, also known as the IEEE 1394 port, allows

transfers of large quantities of data between the computer and an external device, such as a video camera.

The modem port lets you use a RJ11 telephone cable to connect the modem directly to a standard telephone line. For more information, see “Connecting the modem” on page 90.

Finding Your Way Around

Right side

Ether

The LAN port lets you connect the computer to a local area network using a 10/100 Ethernet link.

The cooling vents prevent the computer’s central processing unit (CPU) from overheating so that it can continue to perform at its maximum speed.

CAUTION: To prevent possible overheating of the CPU, make sure you don’t block the cooling vents.

Right side

DVD-ROM or DVD-ROM/CD-RW drive

Manual

eject

button

Volume

control

dial

Microphone in jack

S/PDIF Digital

Optical out

Eject button

The DVD-ROM or DVD-ROM/CD-RW drive enables you to play high-resolution, full-screen videos at up to 30 frames per second. You can also use it to install and run programs from application CD-ROMs and play audio CDs.

The manual eject button enables you to open the drive tray when the computer is off.

CAUTION: Never use a pencil to press the manual eject button. Pencil lead can break off inside the computer and damage it. Instead, use a slim object such as a straightened paper clip.

The eject button opens the drive tray.

The volume control dial lets you adjust the loudness of the system speakers.

The 3.5 mm S/PDIF Digital Optical out lets you connect stereo headphones or other audio-output devices, such as external speakers. Connecting other devices automatically disables the internal speakers.

The 3.5 mm microphone in jack lets you connect an external monaural microphone.

Left side

Finding Your Way Around

Left side

NOTE: The S/PDIF (Sony/Phillips Digital Interface) Digital Optical out is compatible with Dolby* 3D digital sound.

Secure Digital card slot

Secure Digital drive LED

Security lock slot

Cooling vent

The security lock slot allows you to attach an optional PORT- Noteworthy secure it to a large, heavy object such as your desk.

RGB

(monitor)

port

USB port

computer lock cable to your computer to

PC Card Slots

PC Card eject buttons

SmartMedia card slot

SmartMedia drive LED

Finding Your Way Around

Left side

The cooling vent helps keep your computer at an optimum temperature.

CAUTION: To prevent possible overheating of the CPU, make sure you don’t block the cooling vents.

The RGB (monitor) port allows you to connect an external monitor.

The USB (Universal Serial Bus) port allows you to connect USB peripherals to your computer.

The two stacked PC Card slots support up to two Type II PC Cards, or one Type III PC Card. See “Using PC Cards” on

page 182 for more information.

The PC Card eject buttons release PC Cards from the corresponding slots.

The SmartMedia and Secure Digital card drive LEDs (lightemitting diodes) flash when those drives are in use.

The Secure Digital card slot holds a highly secure, stampsize flash memory card with capacities of 16 MB, 32 MB, 64 MB and 128 MB. The card can be used with a variety of digital I/O (input/output) products: digital music players, cellular phones, PDAs, digital cameras, digital video camcorders, etc.

The SmartMedia card slot supports 8 MB (3.3V), 16 MB (3.3V), 32 MB (3.3V), 64 MB (3.3V) and 128 MB (3.3V) SmartMedia Random Access Memory (RAM) cards. These small cards are about one-third the size of conventional PC Cards and are only 0.76mm in thickness. They are used in digital still cameras and various forms of portable information equipment. If the operating system does not recognize an inserted SmartMedia card, remove and insert it again.

Finding Your Way Around

Front with the display open

Power button

Speaker

Screen

Internet button

Keyboard indicator panel

Speaker

Function keys

TouchPad

Primary control button

Secondary control button

The power button turns the computer on and off.

The stereo speakers and subwoofer let you hear sounds, such as system alarms associated with your software, and music from DVD-ROMs and audio CDs.

The function keys, when used with the several different system functions. For more information, see

“Hot Keys” on page 245.

The TouchPad stroke of a finger.

The Primary control button next to the TouchPad acts like the primary button on a mouse.

The Secondary control button next to the TouchPad acts like the secondary button on a mouse.

Sub LCD

TOSHIBA Console button

CD/DVD control buttons

Fn key, activate

enables you to move the cursor with the

Keyboard

Palm rest

System indicator panel

Finding Your Way Around

Front with the display open

The Sub LCD is a display that shows the time and date, track number, and remaining playing time of CD selections.

The CD/DVD control buttons allow you to play audio CDs when the computer is turned off. You can also use them to play CDs and DVDs with the computer turned on. For a description of these controls, see “CD/DVD control buttons”

on page 37.

The lights on the system indicator panel provide information about various system functions. For a description of these lights, see “System indicator panel” on page 36.

The computer’s screen is a liquid crystal display (LCD) that provides clear, sharp images. For more information on your viewing options, see “Your computer’s video modes” on

page 255, or see “Display modes” on page 250.

The Internet button turns on the computer and launches your default Internet browser.

The lights on the keyboard indicator panel provide information about various keyboard functions. For details, see “Keyboard indicator panel” on page 35.

The TOSHIBA Console button allows quick access to various functions.

The 85-key keyboard provides all the functionality of a full- size keyboard. For more information, see “Using the

keyboard” on page 68.

The front panel provides a palm rest to assist you in maintaining proper posture while using the computer.

Keyboard indicator panel

The cursor control mode light glows when the cursor control overlay is on. When this light is on, pressing an overlay key moves the cursor in the direction of the arrow printed on the front of the key instead of typing the letter printed on the top of the key.

Finding Your Way Around

Front with the display open

Cursor control mode light

Numeric mode light

Caps lock light

The numeric mode light glows when the numeric overlay is on. When this light is on, pressing an overlay key types the number printed on the front of the key instead of typing the letter printed on the top of the key.

Caps lock light—The light on the Caps lock is on.

For more information, see “Overlay keys” on page 70.

Caps lock key glows when the

Finding Your Way Around

Front with the display open

System indicator panel

The AC power light glows green when the computer is connected to an external power source.

AC power

Light

On/off light

Battery light

Hard disk drive light

Disc/disk activity light

The on/off light glows green when the computer is on. The light glows amber when the computer is in Stand By mode.

The battery light indicates the main battery’s current charge. It glows green when the battery is fully charged. It glows amber while the battery is being charged. It does not glow if the external power source is disconnected or if the battery is completely discharged. For more information on determining remaining battery power, see “Monitoring battery power” on

page 105.

The hard disk drive light flashes green while the hard disk drive is being accessed.

The disc/disk activity light flashes green when the diskette drive, the DVD-ROM or the DVD-ROM/CD-RW drive is being accessed.

CAUTION: Never turn off the computer while any drive is in use. Doing so may damage the media in use and result in loss of data.

CD/DVD control buttons

The control buttons near the display latch are for playing CDs and DVDs.

Finding Your Way Around

Front with the display open

Mode button

Play/pause

The mode button enables the user to toggle between two modes: digital mode, signified by musical notes graphic on the Sub LCD; and CD mode, signified by a CD disc graphic on the Sub LCD.

The previous track button returns the disc player to the preceding track on the disc.

The next track button causes the disc player to skip to the following track on the disc.

NOTE: If you have set a password for logging onto your system, your computer will start up and you will need to log on before being able to play a CD or DVD.

Next track

Previous track

Sub LCD

Stop/eject

The Sub LCD is a CD display that shows the track number and remaining playing time of selections.

The play/pause button begins play, or makes the disc player pause if currently playing.

Finding Your Way Around

Underside

The stop/eject button stops a disc that is currently playing. Press the button again to eject the disc.

Underside

*Optional

Subwoofer speaker

Battery release latch

The subwoofer speaker allows the user to hear bass sounds.

The Wi-Fi Mini-PCI cover secures a Wi-Fi Mini-PCI card for wireless networking (*for systems with WiFi or Bluetooth).

The modem/LAN cover protects the built-in modem and LAN (Local Area Network) connection.

The expansion memory slot cover protects the slots where you insert additional memory. See “Installing additional

memory (optional)” on page 46 for detailed information.

Wi-Fi Mini-PCI cover

Battery cover

Modem/LAN cover

Expansion memory slot cover

Hard disk drive cover

The battery cover provides access to the battery module, which lets you use your computer when a standard electrical outlet is not available. For information about replacing the battery, see “Changing the main battery” on page 108.

The battery release latch secures the battery cover to the computer, preventing the cover from dislodging from the computer case.

Finding Your Way Around

Underside

The hard disk drive cover protects the computer’s hard disk drive.

Chapter 2

Getting Started

This chapter provides tips for working comfortably, describes how to connect components, and explains what to do the first time you use your notebook computer.

Selecting a place to work

Your computer is portable and designed to be used in a variety of circumstances and locations.

Creating a computer-friendly environment

Place the computer on a flat surface that is large enough for the computer and any other items you need to use, such as a printer. Leave enough space around the computer and other equipment to provide adequate ventilation and prevent overheating.

To keep your computer in prime operating condition, protect your work area from:

❖ Dust, moisture, and direct sunlight.

❖ Equipment that generates a strong electromagnetic field,

such as stereo speakers (other than speakers that are connected to the computer) or speakerphones.

❖ Rapid changes in temperature or humidity and sources of

temperature change, such as air conditioner vents or heaters.

❖ Extreme heat, cold, or humidity.

❖ Liquids and corrosive chemicals.

CAUTION: If you spill liquid into the computer, turn it off, unplug it from the AC power source, and let it dry out completely before turning it on again.

If the computer does not operate correctly after you turn it back on, contact a Toshiba authorized service provider.

Keeping yourself comfortable

Getting Started

Selecting a place to work

Strain and stress injuries are becoming more common as people spend more time using their computers. With a little care and proper use of the equipment, you can work comfortably throughout the day.

This section provides hints on avoiding strain and stress injuries. For more information, consult books on ergonomics, repetitive-strain injury, and repetitive-stress syndrome.

Placement of the computer

Proper placement of the computer and external devices is important to avoid stress-related injuries.

❖ Place the computer on a flat surface at a comfortable

height and distance. You should be able to type without twisting your torso or neck, and look at the screen without slouching.

Getting Started

Selecting a place to work

❖ If you are using an external monitor, the top of the

display should be no higher than eye level.

❖ If you use a paper holder, set it at about the same height

and distance as the screen.

Seating and posture

When using your computer, maintain good posture with your body relaxed and your weight distributed evenly. Proper seating is a primary factor in reducing work strain. Some people find a backless chair more comfortable than a conventional chair.

Below eye level

Approximately 90-degree angles

Footrest

Correct posture and positioning of the computer

Whichever type you choose, use the following guidelines to adjust your chair for maximum computing comfort.

❖ Position your chair so that the keyboard is at or slightly

below the level of your elbow. You should be able to type comfortably with your shoulders relaxed and your forearms parallel to the floor.

If you are using a conventional chair:

❖ Your knees should be slightly higher than your hips. If

necessary, use a footrest to raise the level of your knees and ease the pressure on the back of your thighs.

Getting Started

Selecting a place to work

❖ Adjust the back of your chair so that it supports the lower

curve of your spine. If necessary, use a cushion to provide extra back support. Lower-back-support cushions are available at many office supply stores.

❖ Sit with your back straight so that your knees, hips, and

elbows form approximately 90-degree angles when you work. Do not slump forward or lean back too far.

Lighting

Proper lighting can improve the visibility of the display and reduce eyestrain.

❖ Position the display panel or external monitor so that

sunlight or bright indoor lighting does not reflect off the screen. Use tinted windows or shades to reduce glare.

❖ Avoid placing your computer in front of a bright light that

could shine directly in your eyes.

❖ If possible, use soft, indirect lighting in your computer

work area.

Arms and wrists

❖ Avoid bending, arching, or twisting your wrists. Keep

them in a relaxed, neutral position while typing.

❖ Exercise your hands, wrists, and arms to improve

circulation.

WARNING: Using the computer keyboard incorrectly may result in discomfort and possible injury. If your hands, wrists, and/or arms bother you while typing, stop using the computer and rest. If the discomfort persists, consult a physician.

Work habits

The key to avoiding discomfort or injury from strain is to vary your activities. If possible, schedule a variety of tasks into your working day. Finding ways to break up the routine can reduce stress and improve your efficiency.

❖ Take frequent breaks to change position, stretch your

❖ Avoid performing repetitive activities for long periods.

❖ Focusing your eyes on your computer screen for long

Precautions

Getting Started

Selecting a place to work

muscles, and relieve your eyes. A break of two or three minutes every half-hour is more effective than a long break after several hours.

Intersperse such activities with other tasks.

periods can cause eyestrain. Look away from the computer frequently and focus your eyes on a distant object for at least 30 seconds.

Your notebook computer is designed to provide optimum safety and ease of use, and to withstand the rigors of travel. You should observe certain precautions to further reduce the risk of personal injury or damage to the computer.

❖ Avoid prolonged physical contact with the underside of

the computer.

If the computer is used for long periods, its case can become very warm. While the temperature may not feel too hot to the touch, if you maintain physical contact with the computer for a long time (if you rest the computer on your lap, for example), your skin might suffer low-heat injury.

❖ Never apply heavy pressure to the computer or subject it

to sharp impacts. Excessive pressure or impact can damage computer components or otherwise cause your computer to malfunction.

Getting Started

Setting up your computer

❖ Some PC Cards can become hot with prolonged use. If

two cards are installed, both can become hot even if only one is being used. Overheating of a PC Card can result in errors or instability in its operation.

Be careful when you remove a PC Card that has been used for a long period.

❖ Avoid spilling liquids into the computer’s keyboard.

If you do spill a liquid that gets into the keyboard, turn off the computer immediately. Leave the computer turned off overnight to let it dry out before you use it again.

❖ Never turn off the computer if a drive-in-use light

indicates a drive is active.

Turning off the computer while it is reading from or writing to a disk may damage the disk, the drive, or both.

❖ Keep the computer and disks away from objects that

generate strong magnetic fields, such as large stereo speakers.

Information on disks is stored magnetically. Placing a magnet too close to a disk can erase important files.

❖ Scan all new files for viruses.

This precaution is especially important for files you receive via diskette, email, or download from the Internet. Occasionally, even new programs you buy from a supplier may contain a computer virus. You’ll need a special program to check for viruses. Ask your dealer to help you.

Setting up your computer

Your computer contains a rechargeable high-capacity battery that needs to be charged before you can use it.

To use external power or to charge the battery, you must attach the AC adapter. See “Connecting the AC adapter” on

page 53.

Getting Started

Setting up your computer

To register your computer online, or to sign up for an Internet account, you must connect the built-in modem to a telephone line. See “Connecting the modem” on page 90.

Before starting to use your computer, you may also want to:

❖ Add more memory

❖ Connect a mouse (see “Connecting a mouse” on page 50)

❖ Connect a full-size keyboard (see “Using an external

keyboard” on page 53)

❖ Connect an external monitor (see “Using external display

devices” on page 51)

❖ Connect a local printer (see “Connecting a printer” on

page 50)

❖ Install PC Cards (see “Using PC Cards” on page 182)

Installing additional memory (optional)

Your computer comes with enough memory to run most of today’s popular applications. You may want to increase the computer’s memory if you use complex software or process large amounts of data.

Additional memory comes in 128 MB and 256 MB modules. There are two memory slots. Your system may have both slots occupied.

You need a standard Phillips no. 1 screwdriver to install a memory module.

CAUTION: To avoid damaging the computer’s screws, use a standard Phillips no. 1 screwdriver that is in good condition.

If the computer is on, begin at step 1; otherwise, skip to step

Getting Started

Setting up your computer

1 If the computer is on, click Start, Turn Off Computer.

The Turn off computer window appears.

2 Click Turn O f f.

The operating system turns off the computer.

3 Unplug and remove any cables connected to the

computer.

4 Remove the battery.

5 Close the display panel and turn the computer upside

down to locate the expansion memory slot cover to the empty memory slot.

Expansion memory slot cover

Base of the computer

6 Using a standard Phillips no. 1 screwdriver, unscrew the

two screws that secure the memory slot cover, then remove the memory slot cover.

Getting Started

Setting up your computer

Removing the memory slot cover screws

7 Put the screws and the cover in a safe place so that you

can retrieve them later.

CAUTION: Static electricity can damage the memory module. Before you handle the module, touch a grounded metal surface to discharge any static electricity you may have built up.

To avoid damaging the memory module, be careful not to touch its gold connector bar (on the side you insert into the computer).

8 Remove the new memory module from its antistatic

packaging.

9 Holding the memory module by its edges so that the gold

connector bar faces the slot, fit the module into the socket.

10 Gently press down on the memory module connector

until the clips snap into place.

Do not force the module into position. The memory module should be level when secured in place.

Getting Started

Setting up your computer

Inserting the memory module

CAUTION: Avoid touching the connectors on the memory module or on the computer. Grease or dust on the connectors may cause memory access problems.

11 Replace the memory slot cover.

12 Replace the screws and tighten them.

13 Turn the computer over and reconnect any cables you

removed.

14 To verify that the computer correctly recognizes the

memory:

❖ Click Start, then click Control Panel

❖ Click Performance and Maintenance.

❖ Click System.

❖ The General tab view automatically appears and

shows the recognized memory.

15 If the computer does not recognize the memory, turn off

the computer, remove the memory slot cover, and make sure the memory module is seated properly, as described in step 10.

Getting Started

Connecting a mouse

Removing a memory module

1 Follow steps 1 through 6 in “Installing additional

memory (optional)” on page 46.

2 Gently push the memory locks outward until the memory

module pops up.

3 Gently pull the memory module diagonally out of the

slot.

4 Complete the procedure by following steps 11 through

14.

Connecting a mouse

You may want to use a mouse instead of the TouchPad, the computer’s built-in pointing device. Your computer can accommodate only a USB-compatible mouse.

To connect a mouse, plug the mouse cable into one of the computer’s USB ports.

Connecting a printer

You can connect a USB-compatible printer to your computer through the USB ports. To determine if the printer is USBcompatible, check its documentation.

To achieve the connection, you need a suitable USB cable, which may come with your printer. You can purchase one from a computer or electronics store.

To connect a printer:

1 Connect the USB cable to the USB port.

2 Connect the printer’s power cable to a wall outlet and

turn on the printer.

See your printer documentation for additional configuration steps, or see “Setting up a printer” on page 61.

Using external display devices

Your computer comes with a built-in LCD display, but you can easily attach an external monitor to your computer if you need a larger screen. To do this:

1 Turn off the computer.

2 Connect the monitor’s video cable to the RGB (monitor)

port on the left side of the computer.

3 Connect the monitor’s power cable to a live electrical

outlet.

4 Turn on the external monitor.

5 Turn on the computer.

Getting Started

6 Set the display mode by pressing

Display Properties settings.

Fn + F5, or by setting the

Directing the display output when you turn on the computer

Once you’ve connected an external display device, you can choose to use the internal display only, the external device only, or both simultaneously. The quickest way to change the display output settings is to use the display hot key (

1 While holding down

setting you want takes effect.

This hot key cycles through the settings in the following order:

❖ Built-in display panel only

❖ Built-in display panel and external monitor

simultaneously

❖ External monitor only

❖ Built-in display panel and external video device

simultaneously

❖ Other external video device only

Fn, press F5 repeatedly until the

Fn + F5).

Getting Started

Using external display devices

2 Release the Fn key.

TECHNICAL NOTE: You can also change these settings using the Display Properties box in the Control Panel.

Adjusting the quality of the external display

To obtain the best picture quality from your external display device, you may need to adjust the video settings. See the documentation supplied with the device for additional configuration steps.

TECHNICAL NOTE: In order to use the simultaneous mode, you must set the resolution of the internal display panel to match the resolution of the external display device. The external display device must support a resolution of 640 X 480 or higher.

Display limitations

Keep in mind that the quality of the display will be limited to the capabilities of the external video device.

❖ If the external video device, such as an SVGA monitor, is

capable of displaying at a maximum resolution of 640 x 480 and your system is set for a higher resolution, only part of the desktop will appear on the screen. You can view the “lost” area by scrolling to it.

❖ If you use the display hot key (Fn + F5) to change the

display output with the LCD Display Stretch option enabled and the Display area (resolution) set to 640 x 480 or 800 x 600, the image on the internal display panel may appear stretched.

Getting Started

Connecting an external diskette drive

To use diskettes with your computer, you first need to attach a USB-compatible external diskette drive. These external drives hold 3.5-inch diskettes.

An external USB diskette drive

To connect an external USB diskette drive, connect the cable to one of the computer’s USB ports.

For more information about diskettes, see “Using diskettes”

on page 75.

Using an external keyboard

If you prefer to use a full-size keyboard, you can attach one to your computer provided that keyboard is USB-compatible.

To connect a keyboard, attach its cable to one of the computer’s USB ports.

Connecting the AC adapter

The AC adapter enables you to power the computer from an AC outlet and to charge the computer’s batteries. The AC power light on the computer glows when the device is plugged in.

Power cable

AC adapter

Getting Started

Connecting the AC adapter

Power cable and AC adapter

To connect AC power to the computer:

1 Connect the power cable to the AC adapter.

Connecting the power cable to the AC adapter

2 Plug the AC adapter into the DC-IN jack on the back of

the computer.

Connecting the adapter to the computer

3 Connect the power cable to a live electrical outlet.

Getting Started

Charging the battery

The AC power and battery lights glow.

DANGER: Damaged power cables can cause fire or electric shock. Never modify, forcibly bend, place heavy objects on top of, or apply heat to the power cable.

If the power cable becomes damaged or the plug overheats, discontinue use. There is a risk of electric shock.

Never remove the power plug from the outlet with wet hands. Doing so may cause an electric shock.

CAUTION: Using the wrong AC adapter could damage your computer. Toshiba assumes no liability for any damage in such cases.

Never pull directly on the power cable to unplug it. Hold the power plug when removing the cable from the outlet.

Charging the battery

Before you can use the battery to power the computer, you must charge it. Connect the computer to a live power outlet using the AC adapter and power cable. The on/off light glows green and the battery light glows amber to show that it is charging.

Once the computer is connected to a power outlet, you can charge the battery with the computer turned off or on. It takes several hours to charge the battery when the computer is off. It takes much longer to charge the battery when the computer is on. If the computer is not consuming full power, the time required to charge the battery is reduced.

Getting Started

Using the computer for the first time

For more information on battery use, see “Running the

computer on battery power” on page 100.

CAUTION: Once the battery is charged for the first time, avoid leaving the computer plugged in and turned off for more than a few hours at a time. Continuing to charge a fully charged battery can damage the battery.

Using the computer for the first time

Opening the display panel

Slide the display latch to the right and lift the display panel.

Lift

Opening the display panel

CAUTION: To avoid damaging the display panel, don’t force it beyond the point where it moves easily.

Never lift or move the computer using the display panel.

Turning on the power

1 Check that all the drives are empty.

Slide

Getting Started

Using the computer for the first time

2 If you have a printer connected to your computer, turn on

the printer and wait until the printer indicates that it is ready (on line).

3 Turn on the computer by pressing the power button

located above the keyboard.

Pressing the power button

NOTE: When you turn on the computer for the first time, don’t turn off the power again until the operating system has loaded completely.

The AC power light glows when the computer is connected to an external power source.

The battery light:

❖ Glows amber while the battery is being charged.

❖ Glows green when the battery is fully charged.

❖ Is unlit when the computer is not connected to an

external power source. For information on determining battery power, see “Monitoring battery

power” on page 105.

Getting Started

Using the computer for the first time

The hard disk drive light flashes to indicate that the hard disk drive is currently in use.

CAUTION: Never turn off the computer while any drive is in use.

Activating the power-on password

When you first power up your computer, no password is required. But you can set up your computer so that a password is required to complete the powering up process in the future.

To activate the power-on password:

1 Press the TOSHIBA Console button.

The TOSHIBA Console window appears. For more information see “TOSHIBA Console” on page 119.

2 Click Security.

3 Click User password.

4 Follow the on-screen instructions.

The password requirement becomes active the next time you turn on your computer.

When the feature is active, the Sub LCD will display “password =”during the power-on process. As you type your password, the characters will appear as asterisks in the Sub LCD. After typing your password, hit the Enter key.

If the password is correct, the power-on process continues. If the password is incorrect, “password=” will appear once more and you can try again.

If you forget your power-on password and therefore can’t turn on your computer, take your computer to a Toshiba authorized service center for help.

After the third incorrect password submission, the system automatically shuts down.

Using the TouchPad

The TouchPad, the small, smooth square cutout located in front of the keyboard, is sensitive to touch and enables you to move the cursor with the stroke of a finger. Simply move your finger on the TouchPad in the direction you’d like to move the cursor:

Getting Started

Using the computer for the first time

❖ To move the cursor to the top of the page, push your

finger forward on the TouchPad.

❖ To move the cursor to the bottom of the page, drag your

finger toward yourself.

❖ To move the cursor to the right side of the page, slide

your finger across the TouchPad from left to right.

❖ To move it to the left side, slide your finger from right to

left.

NOTE: Because the TouchPad is much smaller than the display screen, moving your cursor across the screen often means having to move your finger several times across the TouchPad in the preferred direction.

Once you’ve positioned your cursor, you can either click it into place by double-tapping the TouchPad or clicking the

Getting Started

Using the computer for the first time

control buttons. For more on the TouchPad, see “Lesson 2:

Using the TouchPad and control buttons together” on page 133.

Primary and secondary control buttons

When you want to click or choose an item, use the TouchPad to move the pointer/cursor to the item. Once the pointer/ cursor is positioned, you can click it into place by either double-tapping the TouchPad or clicking the control buttons.

The control buttons are adjacent to the TouchPad and are used like the buttons on a mouse. The primary control button is the left one and corresponds to the left mouse button. To doubleclick, press the primary button twice in rapid succession.

The function of the secondary button depends on the program you are using. It usually corresponds to the right mouse button. Check your program’s documentation to find whether it uses the secondary mouse button.

Setting up your software

The first time you turn on your computer, the operating system guides you through several essential steps to set up your software. These steps may or may not appear in the following order:

❖ Select your time zone.

Select one of the time zones listed by clicking the up and down arrow keys to highlight the appropriate time zone, then click Next to change the setting.

❖ Confirm acceptance of Microsoft’s End User License

Agreement and complete information about the operating system.

❖ Registering your computer lets Toshiba keep you up-to-

date with information about new products and upgrades,

Getting Started

Using the computer for the first time

and also extends your Toshiba warranty worldwide at no charge to you.

NOTE: For you to register online, your computer’s modem must be connected to a voice-grade telephone line.

To register your computer at a later time, select No, I do not want to register at this time. To register later,

double-click the Registration icon on your desktop.

NOTE: If you skip the registration the first time you start your computer, a weekly reminder screen will appear a few times to prompt you to do so.

❖ Read about Warranty Extensions and Upgrades.

This step provides important information from Microsoft.

❖ Sign up for Internet access.

This step guides you through signing up for a new Internet account, or assists you in setting up your computer to work with your existing Internet account.

Completing installation

Upon completion, you will be prompted to click Finish to restart your computer.

Setting up a printer

If you started your computer with a printer connected and turned on, it may have been detected automatically. If this is not the case, then you must install the printer driver for the model of printer that is connected to your computer. You install the printer driver either by following the instructions indicated in your printer manual, or by using the operating system’s Add Printer Wizard.

Getting Started

Using the computer for the first time

If you plan to set up a printer later, click Cancel.

Using the Add Printer Wizard

To set up a printer with the Add Printer Wizard:

1 Click Start, Control Panel.

2 Click Printers and Other Hardware.

3 Click Printers and Faxes.

The Printers and Faxes window appears.

Sample Printers and Faxes window

4 Click Add a Printer.

The Add Printer Wizard window appears.

Getting Started

Setting up the fax function

Sample Add Printer Wizard

5 Follow the instructions.

HINT: If you are using more than one printer, make sure the name is descriptive enough to help you tell the difference.

Setting up the fax function

Your system’s auto-receive fax function default setting is disabled.

To enable the function, you must first set up the fax capability.

1 Click Start, Printers and Faxes.

The Printers and Faxes window appears.

2 Click the Set up faxing option in the top-left corner.

3 Follow the on-screen instructions.

To enable the fax function:

1 Click Start, Printers and Faxes.

Getting Started

Turning off the computer

2 Right-click the fax icon.

3 Click Properties from the drop-down menu.

4 Click the Device tab.

5 Under the device name, right-click Toshiba Soft Modem

AMR, highlight Receive and click the auto option.

To disable the auto-receive function, repeat steps 1-4. But under the device name, right-click Toshiba Soft Modem AMR, highlight Receive and click the disable option.

Turning off the computer

It is a good idea to turn off your computer when you are not using it for a while.

If you are using the computer for the first time, leave the computer plugged into a power source (even though the computer is off) to fully charge the main battery. With the computer off, it may take several hours to recharge the main battery.

Guidelines for turning off the computer:

❖ To leave the computer off for a longer period, use the

Windows Hibernation mode to save the system settings to the hard disk.

❖ If you have work in progress and are not connected to a

network, use the operating system Standby command to save your system settings to memory so that, when you turn on the computer again, you automatically return to where you left off.

❖ Never turn off the power while a drive-in-use light on the

system indicator panel is on. Doing so may damage your hard disk, diskette drive, DVD-ROM, DVD-ROM/CDRW drive, SmartMedia or Secure Digital cards.

For more information, see “Powering down the computer” on

page 91.

Turn Off command. Alternatively, use

Caring for your computer

This section gives tips on cleaning and moving your computer, and explains how to fit an antitheft lock. For information about taking care of your computer’s battery, see

“Running the computer on battery power” on page 100.

Cleaning the computer

To keep your computer clean, gently wipe the display panel and exterior case with a lightly dampened cloth. Ask your Toshiba dealer for suggestions for appropriate cleaning products.

CAUTION: Keep liquid, including cleaning fluid, out of the computer’s keyboard, speaker grille, and other openings. Never spray cleaner directly onto the computer. Never use harsh or caustic chemical products to clean the computer.

Getting Started

Moving the computer

Before moving your computer, even across the room, make sure all disk activity has ended (the drive-in-use lights stop glowing) and all external peripheral cables are disconnected.

CAUTION: Never pick up the computer by its display panel or by the back (where the ports are located).

Although your notebook computer is built to withstand reasonable shock and vibration, transport it in a carrying case for long trips. You can purchase a carrying case from your Toshiba dealer or through Toshiba’s Web site at

toshibaaccessories.com.

Getting Started

Caring for your computer

Using a computer lock

You may want to secure your computer to a heavy object such as your desk. The easiest way to do this is to purchase an optional PORT-Noteworthy computer lock cable.

PORT-Noteworthy computer lock cable

To secure the computer:

1 Loop the cable through or around some part of a heavy

object.

Make sure there is no way for a potential thief to slip the cable off the object.

2 Pass the locking end through the loop.

3 Insert the cable’s locking end into the security lock slot

located on the left side of the computer, then rotate the key a quarter turn and remove it.

The computer is now securely locked to deter computer theft.

Locking the computer

Chapter 3

Learning the Basics

This chapter lists some computing tips and provides important information about basic features.

Computing tips

❖ Save your work frequently.

Your work stays in the computer’s temporary memory until you save it to the disk. You will lose all unsaved work, if, for example, a system error occurs and you must restart your computer, or your battery runs out of charge while you are working. Your computer can be configured to warn you when the battery is running low. See “Setting

battery alarms” on page 107.

HINT: Some programs have an automatic save feature that you can turn on. This feature saves your file to the hard disk at preset intervals. See your software documentation for details.

Learning the Basics

Using the keyboard

❖ Back up your files to diskettes (or other removable

storage media) on a regular basis. Label the backup copies clearly and store them in a safe place.

If your hard disk suddenly fails, you may lose all the data on it unless you have a separate backup copy.

❖ Use Disk Defragmenter to conserve disk space and help

your computer perform at its optimal level.

❖ Before turning off the computer, always use the Turn Off

command (unless you want to use Stand By or Hibernation mode as described in “Powering down the

computer” on page 91).

CAUTION: The operating system records information, such as your desktop setup, during its turn-off procedure. If you don’t let it turn off normally, details such as new icon positions may be lost.

Using the keyboard

Function keys

Alt (Alternate) key Fn key Ctrl (Control) key

Parts of the keyboard

Home

End PgDn

PgUp

Ins

Character keys

∗

Del

Windows® keys

End

Character keys

Typing with the character keys is very much like typing on a typewriter, except that:

❖ The spacebar creates a space character instead of just

passing over an area of the page.

❖ The lowercase l (el) and the number 1 are not

interchangeable.

❖ The uppercase letter O and the number 0 are not

interchangeable.

❖ The Caps Lock key changes only the alphabet keys to upper

case — the number and symbol keys are not affected.

Ctrl, Fn, and Alt keys

Alt

Ctrl

Ctrl, Fn and Alt keys

Learning the Basics

Using the keyboard

The

Ctrl, Fn, and Alt keys do different things depending on the

program you are using. For more information, see your program documentation.

Function keys

The function keys (not to be confused with the Fn key) are the 12 keys at the top of the keyboard.

Function keys

F1 through F12 are called function keys because they run

programmed functions when you press them. Used in combination with the run specific functions on the computer.

Fn key, function keys marked with icons

Learning the Basics

Using the keyboard

Windows® special keys

The keyboard provides two keys that have special functions in the operating system:

❖ The Windows

❖ The Application key has the same function as the

secondary (or right mouse) control button.

Overlay keys

790

Home PgUp

78 9

UI OP

Application key

Windows® logo key

logo key opens the Start menu.

()&

∗

456

JKL

End PgDn

12 3

Ins Del

∗

;

End

Sample keyboard overlay keys

The keys with numbers and symbols on the front of them form the numeric and cursor overlay. This overlay lets you enter numeric data or control the cursor as you would using the ten-key keypad on a desktop computer’s keyboard.

Learning the Basics

Using the keyboard

Using the numeric keypad overlay

To turn on the numeric keypad overlay, press Fn and F11 simultaneously. The numeric mode light on the keyboard indicator panel glows when the numeric overlay is on.

You can still use the overlay keys to type alphabetic characters while the numeric overlay is on. To do so:

❖ For lowercase letters, hold down Fn while you type the

letters.

❖ For uppercase letters, hold down both Fn and Shift while

you type the letters.

To use the cursor control overlay when the numeric overlay is on, press and hold down keys. To return to the numeric overlay, release

Shift while you use the cursor control

Shift.

To turn off the numeric keypad overlay, hold down the and press indicator panel goes out.

F11 again. The numeric mode light on the keyboard

Fn key

Using the cursor control overlay

To turn on the cursor control overlay, press Fn and F10 simultaneously. The cursor control mode light on the keyboard indicator panel glows when the cursor control overlay is on.

To type alphabetic characters while the overlay is on:

❖ For lowercase letters, hold down Fn while you type the

letters.

❖ For uppercase letters, hold down both Fn and Shift while

you type the letters.

To use the numeric keypad overlay when the cursor control overlay is on, hold down overlay keys. To return to the cursor control overlay, release

Shift.

Shift while you use the numeric

Learning the Basics

Emulating a full-size keyboard

To turn off the cursor control overlay, hold down the Fn key and press keyboard indicator panel goes out.

F10 again. The cursor control mode light on the

Emulating a full-size keyboard

Although the computer’s keyboard layout is compatible with a standard full-size keyboard, it has fewer keys.

Pressing the of the specially marked keys allows you to emulate a full-size keyboard. For further information and instructions, see

“Assigning a key to a program or document” on page 116.

Fn key simultaneously in combination with one

TOSHIBA Console button

The TOSHIBA Console button allows quick access to some common functions. When the default setting is active, the TOSHIBA Console button brings up the TOSHIBA Console.

Sample Toshiba Console box

For information on how to program the button, see

“TOSHIBA Button Controls” on page 121.

Starting a program

The easiest way to start a program is to click the name of the file that contains the information you want to work on. To find the file, use My Computer or Windows

If you prefer to open the program first, you have four options:

❖ Double-click the icon for the program on your desktop

❖ Use the Start menu

❖ Use Windows

program file

❖ Use the Run dialog box

The Windows step-by-step instructions for starting a program from the Start menu. See “Lesson 6: Starting programs” on page 140.

XP operating system’s tutorial chapter gives

Saving your work

Learning the Basics

Starting a program

Explorer.

Explorer or My Computer to locate the

Before you turn off the computer, save your work to the hard disk drive or a diskette. This is one of the most important rules of computing.

NOTE: Save your data even when you are using the Stand By command, in case the battery discharges before you return to work. Your computer can be configured to warn you when the battery is running low, see “Setting battery alarms” on page 107.

Many programs offer a feature that saves documents at regular intervals, such as every 15 minutes. Check your programs’ documentation to see whether they have an automatic save feature.

Learning the Basics

Printing your work

To save :

❖ A file you are updating, open the program’s File menu

and click Save.

❖ A new file, choose Save As from the File menu, type a

name for the file, and click OK.

HINT: To make another copy of the file you are currently working with, choose Save As from the File menu and give the new file a different name.

For information on how to name a file, see “Windows® XP

file system” on page 132.

Printing your work

Verify that the operating system is set up for your printer as described in “Setting up a printer” on page 61.

TECHNICAL NOTE: You only need to set up the printer the first time you connect it. If you use more than one printer or are changing printers, you will need to set up the operating system to run with the additional printer(s).

To print a file:

1 If your printer is not on, turn it on now.

2 In the File menu of your Windows

Print.

The program displays a Print dialog box.

program, click

Sample Print dialog box

Learning the Basics

Using diskettes

3 Click OK to print.

Using diskettes

The 3.5-inch external diskette drive lets you use high-density (1.44 MB) diskettes for data transfer and storage.

Sample external diskette drive

The diskette activity light glows while the drive is being accessed.

Eject buttonDiskette activity light

Learning the Basics

Using diskettes

Inserting and removing diskettes

1 Hold the diskette so that the arrow on its upper surface

points toward the drive.

2 Push the diskette gently into the drive slot. When the

diskette is in place, the eject button pops out.

To release a diskette from the external drive slot, push the eject button.

CAUTION: Never press the eject button or turn off the computer while the light is glowing. Doing so could destroy data and damage the diskette or the drive.

To access your diskette contents:

1 Click Start, then click My Computer.

2 Double-click the 3 1/2 Floppy (A:) drive.

The diskette contents appear.

Caring for diskettes

❖ Store your diskettes properly to protect them and keep

them clean.

❖ If a diskette is dirty, clean it with a soft cloth moistened in

water. Do not use cleaning fluids.

❖ Never slide back the protective metal cover.

❖ Never touch the magnetic surface of a diskette.

Fingerprints can prevent the drive from reading the data stored on a diskette.

❖ Never twist or bend a diskette.

❖ Keep diskettes at room temperature and avoid exposing

them to direct sunlight. Otherwise data may be lost.

❖ Never place heavy objects on your diskettes.

❖ Never eat, smoke, or use erasers near your diskettes.

Foreign particles can damage the diskette’s surface.

❖ Keep your diskettes away from sources of magnetism,

such as speakers and radios, since these can destroy data.

Backing up your files

Backing up your files means copying individual files to a diskette or copying entire sections of your hard disk to another device, such as a tape drive.

Copying to a diskette

1 Insert a diskette into the external diskette drive.

2 Click Start.

The Start menu appears.

3 Click My Computer.

The My Computer window appears.

Learning the Basics

Backing up your files

4 Double-click the drive that contains the file you want to

copy.

5 Double-click the folder that contains the file, then click

the file you want to copy.

HINT: You can use the Ctrl or Shift keys to select more than one file.

6 Click File, then click Send To.

Learning the Basics

Playing a CD or DVD

7 Click the icon for the diskette drive (3 1/2 floppy [A:]).

HINT: You can also back up a file to a diskette by clicking the file (or files) you want to backup with the secondary button, then pointing to Send To and clicking 3 1/2 Floppy (A:).

Playing a CD or DVD

Your computer has a DVD-ROM or DVD-ROM/CD-RW drive that can read both DVD-ROM and CD-ROM discs.

Digital versatile discs (DVDs) provide a significant increase in data storage and support features that are not available on any other video platform. These features include wide-screen movies, multiple language tracks, digital surround sound, multiple camera angles, and interactive menus. The computer can play high-resolution video at up to 30 frames per second.

NOTE: For optimum DVD performance, it is recommended that you play DVDs while running on AC power rather than battery power.

You use CD-ROMs to load and run software, and to access reference material such as catalogs, as well as listen to music.

A special feature allows you to play audio CDs even when the computer is turned off. For more information, see “CD/DVD

control buttons” on page 80.

Drive components and control buttons

The DVD-ROM or DVD-ROM/CD-RW drive is on the right side of the computer. The CD/DVD control buttons are located at the front edge of the computer and can be accessed when the display panel is closed or open.

Learning the Basics

Playing a CD or DVD

Components

Eject button

DVD-ROM or DVD-ROM/CD-RW drive

Use the eject button to release the disc tray. This button requires power to operate.

CAUTION: Never press the eject button or turn off the computer while the activity light is glowing. Doing so could damage the disc or the drive.

Manual eject button

The manual eject button allows you to manually open the disc tray when power to the computer and the drive is off.

CAUTION: Never use a pencil to press the manual eject button. Pencil lead can break off inside the computer and damage it. Instead, use a slim object such as a straightened paper clip.

HINT: When the computer is off and the DVD-ROM or DVD-ROM/ CD-RW drive is on, press the stop/eject control button to eject a disc.

Learning the Basics

Playing a CD or DVD

CD/DVD control buttons

The control buttons on the front edge of the computer enable you to play audio CDs when the computer is off. You can also use them to play CDs and DVDs when the computer is on.

Mode

track track

CD/DVD control buttons in front of the computer

The mode button switches between the CD/DVD and digital audio modes. You can lock the mode to its current setting by pressing and holding the mode button for four seconds. When the mode button is locked, you cannot switch between the CD/DVD and digital audio modes. To unlock the mode button, press and hold it for four seconds.

The previous track button returns to the preceding track on the disc.

The next track button skips to the following track on the disc.

The Sub LCD is a display screen that shows mode, status and battery level of the computer.

❖ Mode - The left side of the Sub LCD displays one of the

following icons depending on what mode your computer is in:

CD/DVD control

Digital audio

Sub LCD

Play/Pause

Stop/Eject

Lock

❖ Status - The center panel displays the following:

❖ Time

Learning the Basics

Playing a CD or DVD

❖ CD/DVD track time

❖ Power messages:

Status Display

ON Welcome!

OFF See you!

SUSPEND Zzz...

RESET Wake up!

❖ Battery level - the right side of the Sub LCD shows the

battery charge level.

The play/pause button starts playing the disc or makes it pause if currently playing.

The stop/eject button stops a disc that is currently playing and ejects it.

You can eject a disc by pressing the stop/eject button twice. Use this method to eject a disc when the computer is turned off and the sound subsystem is turned on.

CD/DVD control and Digital audio control

The following chart describes CD/DVD control and Digital audio control.

Power is off and you press Play/ Pause

CD player mode and you press the mode button

OS is running and you press Play/Pause

Learning the Basics

Playing a CD or DVD

CD /DVD control Digital Audio Control

If a CD is in the drive, the system enters CD player mode and operates as a stand-alone CD player.

If a DVD is in the drive, the operating system starts and the DVD player starts.

DVD-ROM drive power turns off

If a CD is in the drive, the Windows Media starts and the CD begins to play.

Player

The operating system starts, the TOSHIBA MEDIA PLAYER starts and Digital Audio Data begins to play.

TOSHIBA MEDIA PLAYER starts and Digital Audio Data begins to play.

If a DVD is in the drive, WinDVD starts and the DVD begins to play.

CAUTION: Do not install or remove a memory module while the DVD-ROM drive power is on.

Inserting a disc

WARNING: Before playing an audio CD or a DVD, turn the volume down. Playing the disc at maximum volume could damage your ears. To turn the volume down, use the volume control dial or access the Volume Control program (click Start, All

Programs, Accessories, Entertainment, Volum e Control).

1 If the computer is turned on, press the eject button on the

DVD-ROM or DVD-ROM/CD-RW drive.

Learning the Basics

Playing a CD or DVD

Pressing the eject button

The disc tray partially opens.

CAUTION: To avoid damaging a disc or losing data, check that the disk activity light is off before opening the disc tray.

2 Grasp the disc tray and pull it fully open.

3 Hold the disc by its edges and check that it is clean and

free of dust.

CAUTION: Handle discs carefully. Avoid touching the surface of the disc. Grasp it by its center hole and edge. If you handle the disc incorrectly, you could lose data.

Learning the Basics

Playing a CD or DVD

4 Carefully place the disc in the empty tray with its label

facing up.

Inserting a disc

CAUTION: Be careful not to touch the drive’s lens (located underneath the drive’s spindle) or the area around it. Doing so could cause the drive to malfunction.

5 Gently press the center of the disc onto the spindle until it

locks into place.

Spindle

Disc

Positioning the disc on the spindle

CAUTION: Make sure the disc is properly positioned on the spindle. If you position the disc incorrectly, it can jam the disc tray.

Correct position

Incorrect position

6 Close the disc tray by pressing gently on the center of the

tray until it clicks, indicating that it is locked.

Playing an audio CD

Insert an audio CD and close the disc tray.

Learning the Basics

Playing a CD or DVD

Depending on your default setting, your CD player will be either the Windows Media

Player or the TOSHIBA MEDIA PLAYER. For information on how to set the default, please see “TOSHIBA Button Controls” on page 121.

To access the Windows Media

Player, click Start, then

click Windows Media Player.

Rewind Play Stop Previous track Next track Mute

Sample Windows Media

Volume control

Player screen

Fast forward

Learning the Basics

Playing a CD or DVD

To access TOSHIBA MEDIA PLAYER:

1 Click Start, then click All Programs.

2 Select Accessories and then TOSHIBA MEDIA

PLAYER.

Next track

Previous track

Next playlist

Previous playlist

Rewind

CD mode

Sample TOSHIBA MEDIA PLAYER

3 Select the CD mode button to enable the CD controls.

The CD players’ control panels works much like ordinary compact disc players:

❖ To stop the CD, click the Stop button.

❖ To play the CD or to pause, click the Play/pause button

on the CD Player control panel.

Playing a DVD

This manual has an entire chapter devoted to using WinDVD see “WinDVD 2000” on page 188.

Fast forward

Play

Stop

. For information about how to play back a DVD,

Pause

Learning the Basics

Playing a CD or DVD

Viewing the contents of a CD or DVD

CDs and DVDs contain files just like diskettes and the hard disk. CDs are often used to install software or store files that require a lot of space, such as photographs and large presentation files. You can use Explorer or My Computer to view the contents of any CD or DVD.

Removing a disc with the computer on

CAUTION: Never press the eject button while the computer is accessing the drive. Wait for the disk activity light on the system indicator panel to turn off before opening the disc tray.

1 Locate and press the eject button.

The disc tray partially opens.

2 Grasp the sides of the disc tray and pull it fully open.

3 Remove the disc from the disc tray and place it in its

protective cover.

CAUTION: If the disc is spinning when you open the disc tray, wait for the disc to stop before removing it.

4 Close the disc tray by pressing gently on the center of the

tray until it clicks indicating that it is locked.

Learning the Basics

Playing a CD or DVD

Removing a disc with the computer off

1 Insert a slender object, such as a straightened paper clip,

into the manual eject button access hole.

CAUTION: Never use a pencil to press the manual eject button. Pencil lead can break off inside the computer and damage it.

2 Pull the tray fully open, remove the disc and place it in its

protective cover.

3 Push the tray in to close the drive.

Caring for CDs and DVDs

❖ Store your discs in their original containers to protect

them from scratches and keep them clean.

❖ Never bend a disc or place heavy objects on top of it.

❖ Hold a disc by its outside edge. Fingerprints on the

surface of a compact disc can prevent the drive from reading the data properly.

❖ Avoid exposing discs to direct sunlight or extreme heat or

cold.

❖ To clean a disc, wipe it from the center outwards (not in a

circle) with a clean, dry cloth. If necessary, moisten the cloth with water or a neutral cleaner (not benzine or rubbing alcohol). Let the disc dry completely before inserting it in the drive.

Learning the Basics

Using the DVD-ROM or DVD-ROM/CD-RW multifunction

drive

Using the DVD-ROM or DVD-ROM/CD-RW multifunction drive

Your computer may come with a DVD-ROM or DVD-ROM/ CD-RW multifunction drive that allows you to:

❖ Play prerecorded DVDs

❖ Play prerecorded CDs

❖ Read and write files (including music) to a CD-

Recordable (CD-R) or CD-ReWritable (CD-RW) disc.

CAUTION: Check the disc/disk activity light when you use the DVD-ROM or DVD-ROM/CD-RW drive. Do not press the eject button, disconnect a drive or turn off the computer while the light is glowing. Doing so could damage the CD, DVD or drive.

Setting up for communications

To communicate across the telephone lines with another computer, you need:

❖ The computer’s modem

❖ A telephone line

❖ A communications program

To connect to the Internet, you need a Web browser, such as Microsoft

Internet Explorer.

TECHNICAL NOTE: Disable Call Waiting before you connect through the modem. Call Waiting interrupts data transmission.

Learning the Basics

Setting up for communications

Connecting the modem

Your computer comes with a built-in V.90 56K modem and a built-in 10/100 Ethernet LAN adapter. To use the modem, you must connect it to a standard voice-grade RJ11 telephone line.

NOTE: Due to FCC limitations, speeds of 53 kbps are the maximum permissible rates during downloads. Actual data transmission speeds will vary depending on line conditions.

1 Attach one end of a standard RJ11 telephone cable to the

modem port on the back of the computer.

Connecting the internal modem

2 Plug the other end of the RJ11 telephone cable into the

modular jack of a standard voice-grade telephone line.

Connecting your computer to a network

You can connect your computer to a network locally or remotely.

❖ Locally, using the built-in 10/100 Ethernet LAN adapter

by connecting it to a standard RJ45 LAN line.

❖ Remotely, using the built-in modem and a dial-up

connection.

Learning the Basics

Powering down the computer

To set up the network connection, use the Network Setup Wizard:

1 Click Start and point to All Programs.

2 Point to Accessories, then to Communications, and

click Network Setup Wizard.

3 Follow the on-screen instructions.

The computer connects with the network.

Powering down the computer

When you power down the computer, you have three options to choose from: Turn Off, Hibernation, and Stand By. Each option has its advantages.

Turn Off command

The Turn Off command shuts the computer down completely. When you start up again, the computer runs a self-test and loads the operating system. You must open any programs and files you want to use.

Factors to consider when choosing Turn Off:

❖ No power is used while the computer is turned off. This

is the most efficient mode if you will be away from your computer for an extended time.

❖ Restarting from Turn Off uses the most time and battery

power.

❖ When starting up again, the system does not

automatically open programs and files you were previously using.

Hibernation command

Hibernation mode shuts the computer down completely, but it first saves the current state of the computer to the hard disk. Since Hibernation mode does not require power to maintain the saved information, the system settings are retained

Learning the Basics

Powering down the computer

indefinitely. Restoring information from the hard drive takes longer than restoring it from memory. When you start up again, the computer runs a self-test, loads the operating system, and then returns to the state in which you left it.

Factors to consider when choosing Hibernation mode:

❖ While in Hibernation mode, the computer uses no battery

power.

❖ Because the state of the system is held on the hard disk,

no data is lost if the battery discharges.

❖ Restarting from Hibernation mode uses less time and

battery power than restarting from Turn Off.

❖ Restarting from Hibernation mode uses a little more time

and battery power than restarting from Stand By because information is being retrieved from the hard disk instead of memory.

❖ When starting up again, the computer returns to the state

in which you left it, including all open programs and files you were using.

Stand By command

The Stand By command puts the computer into a powersaving mode. Stand By holds the current state of the computer in memory so that, when you restart the computer, you can continue working from where you left off.

Factors to consider when choosing Stand By:

❖ While in Stand By mode, the computer uses some battery

power. A fully charged battery will last up to eight hours in Stand By mode.

NOTE: If you power down using the Stand By command and the battery discharges fully, your information will be lost. Be sure to save your work often.

❖ Restarting from Stand By mode uses less time and

battery power than restarting from Turn Off or Hibernation mode.

❖ When starting up again, the computer returns to the state

in which you left it, including all open programs and files you were using.

TECHNICAL NOTES: Before using any of these options to power down your computer, save your files and make sure the drive-inuse lights are off.

If you change your mind and decide to continue working, wait a few seconds before turning the computer on again.

Using Turn Off

To turn off the computer:

Learning the Basics

Using Turn Off

1 Click Start, select Turn Off Computer.

The Turn off computer box appears.

Sample Turn off computer dialog box

2 Click Turn O f f.

The computer shuts down completely.

Learning the Basics

Using Turn Off

Shutting down more quickly

You can also shut down the computer by pressing the power button or closing the display panel.

To use either of these methods, you first need to turn on the feature in Toshiba’s Power Saver utility.

1 Click Start, then click Control Panel.

The Control Panel appears.

2 Click Performance and Maintenance.

3 Double-click the Tos h ib a Pow e r S av er icon.

4 In the Running on batteries area, click the Details button,

then select the System Power Mode tab.

The following screen appears.

Sample System power mode settings

5 Select Shutdown for the options you want.

Learning the Basics

Using Hibernation

❖ When I press the power button

Set this option to Shutdown to have the computer shut down when you press the power button.

❖ When I close the lid

Set this option to Shutdown to have the computer shut down when you close the display panel.

6 Click Override all Modes with settings here.

7 In the Set to range dialog box, do one of the following:

❖ Click DC only for the settings to apply only when

you are using battery power.

❖ Click All for the settings to apply whether you are

using battery power or outlet power.

8 Click OK.

9 Click OK again, then close the Control Panel.

NOTE: For more information about the Power Saver utility, see

“Power Management” on page 124.

Starting again after Turn Off

To start the computer up again, press and hold the power button until the on/off light changes to green.

Using Hibernation

To power down the computer using Hibernation:

1 Click Start, select Turn Off Computer.

The Turn off computer box appears.

2 Hold down the shift key.

The Stand By option changes to the Hibernate option.

3 Click Hibernate.

Learning the Basics

Using Hibernation

Sample Turn off computer dialog box with Hibernate option

The computer saves the state of the system, including all open programs and files, to the hard disk, and then powers down completely.

Going into Hibernation mode more quickly

You can also put the computer into Hibernation mode by pressing the power button or closing the display panel.

To use either of these methods, you first need to turn it on in Toshiba’s Power Saver utility.

1 Click Start, then click Control Panel.

The Control Panel appears.

2 Click Performance and Maintenance.

3 Double-click the Tos h ib a Pow e r S a v e r icon.

4 In the Running on batteries area, click the Details button,

then select the System Power Mode tab.

5 Select Hibernation for the options you want.

❖ When I press the power button

Set this option to Hibernation for the computer to go into Hibernation mode when you press the power button.

❖ When I close the lid

Set this option to Hibernation for the computer to go

Learning the Basics

into Hibernation mode when you close the display panel.

6 Click Override all Modes with settings here.

7 In the Set to range dialog box, do one of the following:

❖ Click DC only for the settings to apply only when

you are using battery power.

❖ Click All for the settings to apply whether you are

using battery power or outlet power.

8 Click OK.

9 Click OK again, then close the Control Panel.

NOTE: For more information about the Power Saver utility, see

“Power Management” on page 124.

Starting again from Hibernation mode

Using Stand By

To start the computer from Hibernation mode, press the power button until the on/off light turns green. The computer returns to the screen you were using.

If you put the computer in Hibernation mode by closing the display panel, you can start it again by opening the display panel.

Using Stand By

To power down the computer using the Stand By command:

1 Click Start, select Turn Off Computer.

The Turn off computer box appears.

2 Click Stand By.

Learning the Basics

Using Stand By

Sample Turn off computer dialog box

The computer saves the state of all open programs and files to memory, turns off the display, and goes into a low-power mode. The on/off light blinks amber indicating the machine is in Stand By mode.

Going into Stand By mode more quickly

You can also put the computer into Stand By mode by either pressing the power button or closing the display panel.

To use any of these methods, you first need to enable them in Toshiba’s Power Saver utility.

1 Click Start, then click Control Panel.

The Control Panel appears.

2 Click Performance and Maintenance.

3 Double-click the Tos h ib a Pow e r S a v e r icon.

4 In the Running on batteries area, click the Details button,

then select the System Power Mode tab.

5 Select Stand By for the options you want.

❖ When I press the power button

Set this option to Stand By for the computer to go into Stand By mode when you press the power button.

❖ When I close the lid

Set this option to Stand By for the computer to go

into Stand By mode when you close the display panel.

6 Click Override all Modes with settings here.

7 In the Set to range dialog box, do one of the following:

❖ Click DC only for the settings to apply only when

you are using battery power.

❖ Click All for the settings to apply whether you are

using battery power or outlet power.

8 Click OK.

9 Click OK again, then close the Control Panel.

NOTE: For more information about the Power Saver utility, see

“Power Management” on page 124.

Starting again from Stand By

Learning the Basics

Using Stand By

To start the computer from Stand By mode, press and hold the power button until the on/off light changes to green. The computer returns to the screen you were using.

If you put the computer in Stand By mode by closing the display panel, you can start it again by opening the display panel.

NOTE: If you power down using the Stand By command and the battery discharges fully, your information will be lost. Be sure to save your work often.

Chapter 4

Mobile Computing

This chapter covers all aspects of using your computer while traveling.

Toshiba’s energy-saver design

Your computer enters a low-power mode when it is not being used, thereby conserving energy and saving money in the process. It has a number of other features that enhance its energy efficiency.

Many of these energy-saving features have been set by Toshiba. We recommend you leave these features active, allowing your computer to operate at its maximum energy efficiency, so that you can use it for longer periods while traveling.

Running the computer on battery power

The computer contains a removable lithium ion (Li-ion) high-capacity battery that provides power when you are away from an AC outlet. You can recharge it many times.

In addition, the computer has an internal real-time clock (RTC) battery. This is a nickel metal hydride (NiMH) battery.

100

Toshiba 5005 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Satellite® 5005 Series User’s Guide

Contents

Introduction

This guide

Safety icons

Other icons used

Other documentation

Service options

Making sure you have everything

Front with the display closed

Back

Right side

Left side

Front with the display open

Keyboard indicator panel

System indicator panel

CD/DVD control buttons

Underside

Selecting a place to work

Creating a computer-friendly environment

Keeping yourself comfortable

Precautions

Setting up your computer

Installing additional memory (optional)

Connecting a mouse

Connecting a printer

Using external display devices

Adjusting the quality of the external display

Display limitations

Connecting an external diskette drive

Using an external keyboard

Connecting the AC adapter

Charging the battery

Using the computer for the first time

Opening the display panel

Turning on the power

Activating the power-on password

Using the TouchPad

Setting up your software

Setting up a printer

Setting up the fax function

Turning off the computer

Caring for your computer

Cleaning the computer

Moving the computer

Using a computer lock

Computing tips

Using the keyboard

Character keys

Ctrl, Fn, and Alt keys

Function keys

Windows® special keys

Overlay keys

Emulating a full-size keyboard

TOSHIBA Console button

Starting a program

Saving your work

Printing your work

Using diskettes

Inserting and removing diskettes

Caring for diskettes

Backing up your files

Copying to a diskette

Playing a CD or DVD

Drive components and control buttons

CD/DVD control buttons

CD/DVD control and Digital audio control

Inserting a disc

Playing an audio CD

Playing a DVD

Viewing the contents of a CD or DVD

Removing a disc with the computer on

Removing a disc with the computer off

Caring for CDs and DVDs

Using the DVD-ROM or DVD-ROM/CD-RW multifunction drive

Setting up for communications