Integrated High Definition LED
Television User’s Guide:
42L6200U
47L6200U
55L6200U
47L7200U
55L7200U
If you need assistance:
Toshiba's Support Web site
Toshiba Customer Support Center:
Calling within the United States at (800) 631-3811
Calling from outside the United States at (949) 583-3050
For more information, see “Troubleshooting” on page 181 in this guide.
Owner's Record
The model number and serial number are on the back and side of your television.
Record these numbers, whenever you communicate with your Toshiba dealer
about this Television.
Model name: ______________________________________________
Serial number: _______________________________________________
Register your Toshiba Television at register.toshiba.com
support.toshiba.com
Note: To display a High Definition
picture, the TV must be receiving a
High Definition signal (such as an overthe-air High Definition TV broadcast, a
High Definition digital cable program, or
a High Definition digital satellite
program). For details, contact your TV
antenna installer, cable provider, or
satellite provider
GMA300007010
3/12
2
Congratulations on your purchase! As you enjoy your
new product, please keep these safety tips in mind:
The Issue
• The home theater entertainment experience is a growing trend
and larger flat panel displays are popular purchases. However,
flat panel displays are not always supported on the proper stands
or installed according to the manufacturer’s recommendations.
• Flat panel displays that are
inappropriately situated on dressers,
bookcases, shelves, desks,
speakers, chests or carts may fall
over and cause injury.
TOSHIBA Cares!
• The consumer electronics industry
is committed to making home
entertainment enjoyable and safe.
Tune Into Safety
•
One size does NOT fit all. Follow the manufacturer’s recommendations
for the safe installation and use of your flat panel display.
• Carefully read and understand all enclosed instructions for
proper use of this product.
• Don’t allow children to climb on or play with furniture and
television sets.
• Don’t place flat panel displays on furniture
that can easily be used as steps, such
as a chest of drawers.
• Remember that children can
become excited while watching a
program, especially on a “larger
than life” flat panel display. Care
should be taken to place or install
the display where it cannot be
pushed, pulled over, or knocked down.
• Care should be taken to route all cords and
cables connected to the flat panel display so that they cannot be
pulled or grabbed by curious children.
Wall Mounting: If you decide to wall mount your
flat panel display, always:
• Use a mount that has been recommended by the display
manufacturer and/or listed by an independent laboratory (such
as UL, CSA, ETL).
• Follow all instructions supplied by the display and wall mount
manufacturers.
• If you have any doubts about your ability to safely install your
flat panel display, contact your retailer about professional
installation.
• Make sure that the wall where you are mounting the display is
appropriate. Some wall mounts are not designed to be mounted
to walls with steel studs or old cinder block construction. If you
are unsure, contact a professional installer.
• A minimum of two people are
required for installation. Flat panel
displays can be heavy.
CHILD SAFETY:
It Makes A Difference How and Where You Use Your Flat
Panel Display
Dear Customer,
Thank you for purchasing this Toshiba LED TV. This
manual will help you use the many exciting features of
your new LED TV. Before operating your LED TV,
carefully read this manual completely .
WARNING
To prevent injury, this apparatus must be securely
attached to the floor/wall in accordance with the
installation instructions. See item 26) on page 4.
WARNING: If you decide to wall mount this
television, always use a mounting bracket that has
been Listed by an independent laboratory (such as
UL, CSA, ETL) and is appropriate for the size and
weight of this television. The use of inappropriate or
non-Listed mounting brackets could result in serious
bodily injury and/or property damage. See “To
Display your LED TV using a Wall Bracket:” on
page 5.
NOTE TO CATV INSTALLERS
This is a reminder to call the CATV system installer’s
attention to Article 820-40 of the U.S. NEC, which
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building, as
close to the point of cable entry as practical. For
additional antenna grounding information, see items
33) and 34) on page 4.
3
WARNING: NEVER expose
batteries to excessive heat such as
sunshine, fire, or the like.
DANGER: RISK OF
SERIOUS PERSONAL
INJURY, DEA TH, OR
EQUIPMENT DAMAGE!
Important Safety Instructions
1)
Read these instructions.
2)
Keep these instructions.
3)
Heed all warnings.
4)
Follow all instructions.
5)
Do not use this apparatus near water.
6)
Clean only with dry cloth.
7)
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8)
Do not install near any heat sources such as
radiators, heat registers, stoves, or other products
(including amplifiers) that produce heat.
9)
Do not defeat the safety purpose of
the polarized or grounding type
plug. A polarized plug has two
blades with one wider than the
other. A grounding type plug has
two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10)
Protect the power cord from being walked on or
pinched, particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
11)
Only use attachments/a ccessories specified by
the manufacturer.
12)
Use only with the cart, stand,
tripod, bracket, or table
specified by the manufacturer,
or sold with the apparatus.
When a cart is used, use caution
when moving the cart/apparatus
combination to avoid injury from
tip-over.
13)
Unplug this apparatus during lightning storms
or when unused for long periods of time.
14)
Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way , such as
power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the
apparatus, the apparatus has been exp osed t o r a i n
or moisture, does not operate normally, or has been
dropped.
Additional Safety Precautions
14a)
CAUTION: If the TV is dropped and the cabinet or
enclosure surface has been damaged or the TV
does not operate normally, take the following
precautions:
• ALW AYS turn off the TV and unplug the power cord
to avoid possible electric shock or fire.
• NEVER allow your body to come in contact with
any broken glass or liquid from the damaged
television. The LCD panel inside the TV contains
glass and a toxic liquid. If the liquid comes in
contact with your mouth or eyes, or your skin is
cut by broken glass, rinse the affected area
thoroughly with water and contact your doctor
immediately.
• ALWAYS contact a service technician to inspect
the TV any time it has been damaged or
dropped.
15)
CAUTION:
• To reduce the risk of electric shock, do not use
the polarized plug with an extension cord,
receptacle, or other outlet unless the blade s ca n
be inserted completely to prevent blade
exposure.
• T o prevent electric shock, match wide blade of plug
to wide slot; fully insert.
16)
CAUTION:
• Do not let children swallow any small parts
included on or with the product or play with the
plastic bag. Keep the small parts and the plastic
bag out of the reach of children.
17)
CAUTION:
• Do not let water or other liquids come into
contact with the product, as it may result in
damage.
18)
WARNING:
• To prevent the spread of fire, keep candles or
other open flames away from this product at all
times.
• Keep the product away from direct sunlight, fir e
or a heat source such as a heater. This may
reduce the product lifetime or result in fire.
Installation, Care, and Service
Installation
Follow these recommendations and precautions and
heed all warnings when installing your TV:
19)
20)
ALWAYS plug the product into an outlet that is
located in such a manner that it can be easily
unplugged in case the product requires service.
21)
NEVER route the product’s power cord inside a
wall or similar enclosed area.
22)
Never modify this equipment. Changes or
modifications may void: a) the warranty, and b) the
user’s authority to operate this equipment under
the rules of the Federal Communications
Commission.
23)
Never place the TV on an unstable
cart, stand, or table. The TV may
fall, causing serious personal injury,
death, or serious damage to the TV.
4
WARNING: RISK OF SERIOUS
PERSONAL INJURY OR
EQUIPMENT DAMAGE!
24)
When selecting a location for the TV,
• NEVER allow any part of the TV to hang over
the edge of the supporting furniture,
• NEVER place the TV on tall furniture (for
example, entertainment centers or bookcases)
without anchoring both the furniture and the TV
to a suitable support,
• Never place cloth or other material between the
TV and the supporting furniture.
• NEVER allow children to climb on the TV
25)
To avoid damage to this product, never place or
store the TV in direct sunlight; hot, humid areas; or
areas subject to excessive dust or vibration.
26)
Always place the TV on the floor or a sturdy, level,
stable surface that can support the weight of the
unit. To secure the TV, use a sturdy strap from the
hook(s) on the rear of the TV to a wall stud, pillar,
or other immovable structure. Make sure the strap
is tight, secure, and parallel to the floor.
27)
The apparatus shall not be ex po se d to dripping or
splashing, and that no objects filled with liquids,
such as vases, shall be placed on the apparatus.
28)
Never block or cover the slots or openings in the
TV cabinet back, bottom, and sides. Never place
the TV:
• on a bed, sofa, rug, or similar surface;
• too close to drapes, curtains, or walls; or
• in a confined space such as a bookcase, built- in
cabinet, or any other place with poor ventilation.
The slots and openings are provided to protect the
TV from overheating and to help maintain reliable
operation of the TV. Leave a space of at least 4
(four) inches around the TV.
29)
Always leave a space of at least 4 (four) inches
around the TV. The slots and openings are
provided to protect the TV from overheating and to
help maintain reliable operation of the TV.
30)
Never allow anything to rest on or roll over the
power cord, and never place the TV where the
power cord is subject to wear or abuse.
31)
Never overload wall outlets and extension cords.
32)
Always operate this equipment from a 120V AC,
60 Hz power source.
33)
Always make sure the antenna system is properly
grounded to provide adequate protection against
voltage surges and built-up static charges (see
Section 810 of the National Electric Code).
34)
DANGER: RISK OF SERIOUS
• Use extreme care to make sure you are never in
• Never attempt to install any of the following
PERSONAL INJURY OR DEATH!
a position where your body (or any item you are
in contact with, such as a ladder or screwdriver)
can accidentally touch overhead power lines.
Never locate the antenna near overhead power
lines or other electrical circuits.
during lightning activity: a) an antenna system;
or b) cables, wires, or any home theater
component connected to an antenna or phone
system.
Care
For better performance and safer operation of your
TOSHIBA TV, follow these recommendations and
precautions:
35)
If you use the TV in a room whose temperature is
32° F (0° C) or below, the picture brightness may
vary until the LCD warms up. This is not a sign of
malfunction.
36)
• Never use chemicals (such as air fresheners,
cleaning agents, etc.) on or near the TV
pedestal. Studies indicate that plastics may
weaken and crack over time from the combined
effects of chemical agents and mechanical
stress (such as the weight of the TV). Failure to
follow these instructions could result in serious
injury and/or permanent damage to TV and TV
pedestal.
• Always unplug the TV before cleaning. Gently
wipe the display panel surface (the TV screen)
using a dry, soft cloth (cotton, flannel, etc.). A
hard cloth may damage the surface of the panel.
Avoid contact with alcohol, thinner, benzene,
acidic or alkaline solvent cleaners, abrasive
cleaners, or chemical cloths, which may damage
the surface. Never spray volatile compounds
such as insecticide on the cabinet. Such
products may damage or discolor the cabinet.
37)
Never hit, press, or place anything on the back
cover. These actions will damage internal parts.
5
WARNING: RISK OF SERIOUS
PERSONAL INJURY OR
EQUIPMENT DAMAGE!
38)
WARN ING:
RISK OF ELECTRIC SHOCK!
Never spill liquids or push objects of any kind into
the TV cabinet slots.
39)
During a lightening storm, do not touch the
connecting cables or product.
40)
For added protection of your TV from light ning and
power surges, always unplug the power cord and
disconnect the antenna from the TV if you leave
the TV unattended or unused for long periods of
time.
41)
Always unplug the TV to completely disconnect
from mains power. When the TV is turned of f using
the on/off switch, it is not completely disconnected
from power and a minute amount of current is still
consumed.
42)
During normal use, the TV may make occasional
snapping or popping sounds. This is normal,
especially when the unit is being turned on or off. If
these sounds become frequent or continuous,
unplug the power cord and contact a Toshiba
Authorized Service Provider.
43)
Never strike the screen with a sharp or heavy
object.
44) •
The LCD screen of this product can be damaged
by ultraviolet radiation from the sun. When
selecting a location for the television, avoid
locations where the screen may be exposed to
direct sunlight, such as in front of a window .
• Never touch, press, or place anything on the
LCD screen. These actions will damage the LCD
screen. If you need to clean the LCD screen
follow the instructions (in item 36) on page 4.
Service
WARN ING:
RISK OF ELECTRIC SHOCK!
Never attempt to service the TV yourself. Opening
and removing the covers may expose you to
dangerous voltage or other hazards. Failure to
follow this WARNING may result in death or
serious injury. Ref er all servicing not specified in
this manual to a Toshiba Authorized Service
Provider.
45)
If you have the TV serviced:
• Ask the service technician to use only
replacement parts specified by the
manufacturer.
• Upon completion of service, ask the service
technician to perform routine safety checks to
determine that the TV is in safe operating
condition.
Choosing a location for your LED TV
To Display your LCD TV on the included Pedestal
Stand:
Observe the following safety precautions:
1)
Read and follow the pedestal assembly
instructions included with the pedestal.
CAUTION: Before beginning pedestal assembly,
carefully lay the front of the LCD Panel face down
on a flat, cushioned surface such as a quilt or
blanket. Leave the bottom of the unit protruding
over the edge of the surface and assemble the
pedestal as indicated below.
Note: Extreme care should always be used when
attaching the pedestal stand to avoid damage to
the LCD panel.
2)
Place the TV on a sturdy, level surface that can
support the weight of the TV.
3)
Be sure to secure the TV to a wall, pillar, surface,
or other immovable structure see item 26) page 4
for additional details.
To Display your LED TV using a Wall Bracket:
If you decide to wall mount your LED TV , always use a
wall bracket Listed by an independent laboratory
(such as UL, CSA, ETL) that is appropriate for the size
and weight of the TV (see page 2):
1)
CAUTION: Two people are required for
installation.
2)
Unplug and remove any cables and/or other
component connectors from the rear of the TV.
3)
Remove the screws of the VESA Mounting Pattern
show in the table below.
CAUTION: Do not use the screws removed from
the back cover to attach the wall mount bracket to
the TV .
4)
Always use the screws supplied or recommended
by the wall mount manufacturer.
5)
Follow the instructions provided with your wall
bracket. Before proceeding, make sure the
appropriate bracket(s) are attached to the wall and
the back of the TV as described in the instructions
provided with the wall bracket.
6)
After attaching the appropriate bracket(s) to the
wall and the back of the TV, remove the pedestal
stand from the TV, as described below.
Carefully lay the front of the unit face down on a
flat, cushioned surface such as a quilt or blanket.
Leave the stand protruding over the edge of the
surface.
Note: Extreme care should always be used when
removing the pedestal stand to avoid damage to
the LCD panel.
2)
Remove the screws shown in the below diagram.
This will allow removal of the pedestal stand.
3)
Once you have removed all of the screws holding
the pedestal stand in place, remove the pedestal
stand from the TV.
CAUTION: Always place the TV on the floor or a
sturdy, level, stable surface that can support the
weight of the unit. Secure the TV with the
securement clip and a sturdy strap from the hooks
on the rear of the TV pedestal to a wall stud, pillar ,
or other immovable structure. Make sure the strap
is tight, secure, and parallel to the floor.
Safety Precautions for 3D glasses
About handling the 3D glasses
•
Do not repair , modify , or di sassemble the 3D glas ses
by yourself. Doing so may cause you to become
indisposed while viewing 3D images.
CAUTION:
About the 3D glasses
•
Carefully read instructions p rovided wi th your
display and/or 3D glasses before 3D viewin g.
•
Do not use the 3D glasses if they are cr acked,
broken, or not working properly.
Continuing to use them in such a state may cause
injury, eye strain, or indisposition.
•
Do not drop, exert pressu re on, or step on the 3D
glasses. Doing so may damage the glass section which
may result in injury . Exposing the 3D glasses to liquid or
excessive heat may damage the function.
•
Do not stand or walk wh ile weari ng 3D g lasses.
You may lose your balan ce which could result in fall s
or other accidents.
•
Do not wear the 3D glasses for any purpose other
than viewing 3D programming.
3D glasses do not function as sunglasses.
•
If your nose or temple turns red, or you feel any p ain
or discomfort, stop using the 3D glasses.
Such symptoms may occur when wearing 3D
glasses for long periods of time.
Cautions on watching the 3D images
•
Some viewers may experience a seizu re or blackout
when exposed to certain flashing imag es or light s
contained in certain 3D television pictures or video
games.
Anyone who has had a seizure, loss of awareness, or
other symptom linked to an epileptic condition, or has
a family history of epilepsy, should contact a health
care professional before using the 3D function.
•
Avoid using the 3D function when under the
influence of alcohol.
•
Some individuals may experience health-r elated
complications when exposed to certain 3D images.
Parents should monitor and/or supervise their children's
use of this 3D technology. If you or your child should
experience any problem, immediately sto p using this 3D
technology and consult a physician.
•
If you are ill or feel ill, you should refrain from
viewing 3D images, and consult your health care
provider as may be appropriate.
•
If you experience any of the fo llowing symptoms
when viewing 3D video images, stop viewing and
contact your health care provider:
Convulsions, Eye or muscle twitching, Loss of
awareness, Altered vision, Involuntary movements,
Disorientation, Eye Strain, Nausea/Vomiting,
Dizziness, Headaches, Fatigue.
•
If you feel eye fatigue or other discomfort from
viewing 3D video images, stop vie wing a nd t ake a
rest until the condition improves.
•
Viewing in 3D may cause dizziness and/or
disorientation for some vi ewers.
Therefore, to avoid injury do not place your TV near
open stairwells, balconies, or wires.
Also do not sit near objects that could be broken if
accidentally hit.
•
When viewing 3D images, always wear 3D glasses.
Watching 3D images without specified 3D glasses
may cause eye strain.
•
Do not wear 3D glasses or watch 3 D image s from
steep angles or while lying down.
The 3D effect is lost in these conditions and eye
strain may result.
•
It is recommended that the viewer’s eyes and 3D
glasses are level with the screen.
•
If you have prescription eye glasses or contact
lenses, wear the 3D glasses over them.
Watching 3D images without appropriate eyewear
may cause eye strain.
•
If 3D images often appear doubled or if you cannot
see the images in 3D, stop viewing.
Continuous viewing may cause eye strain.
•
Due to the possible impact on vision devel opment,
viewers of 3D video images should be age 6 or
above.
Children and teenagers may be more susceptible to
Center of Display
Viewing Angle
Viewing Distance
Same height as
Center of Display
Viewing angleModelViewing distance
42L6200U
Approx. 20 degrees
Over 62 inches
47L6200U
Approx. 20 degrees
Over 69 inches
55L6200U
Approx. 20 degrees
Over 81 inches
47L7200U
Approx. 26 degrees
Over 69 inches
55L7200U
Approx. 26 degrees
Over 81 inches
health issues associated with viewing in 3D and
should be closely supervised to avoid prolonged
viewing without rest.
•
Watching TV while sitting too close to the screen for
an extended period of time may cause eye strain.
•
For optimal 3D effect and to avoid eye fatigue it is
important that you properly select your viewing
position.
The best viewing position is at the indicated viewing
distance with your eyes at the same level as the
center of the display as shown below. The center of
the optimum viewing area varies from set to set. The
usable viewing area is generally over the range
shown in the table below (actual angle not depicted
in drawing).
Important: If you see a double image, your eyes are
either too high or too low in relation to the horizontal
center of the screen. Adjust your position so that it is
closer to the center to avoid eye fatigue and to enjoy
optimum 3D effects.
FCC Caution
To assure continued compliance, follow the
attached installation instructions. Any changes
or modifications not expressly approved by
Toshiba America Information Systems, Inc. could
void the user’s authority to operate this device.
Service Center or an experienced radio/TV
technician for help.
7
FCC Declaration of Conformity
Compliance Statement (Part 15):
Toshiba television models 42L6200U, 47L6200U,
55L6200U, 47L7200U, and 55L7200U comply with Part
15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired operation.
The party responsible for compliance to these rules is:
Toshiba America Information Systems, Inc.
9740 Irvine Blvd., Irvine, CA 92618.
Ph: 800-631-3811
Note: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limit s are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by removing and applying
power to the equipment, the user is encouraged to try
to correct the interference by one of the following
measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and
receiver.
•
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician
for help.
Caution: Changes or modifications to this equipment
not expressly approved by Toshiba could void the
user's authority to operate this equipment.
Wireless Radio
For product available in the USA/Canada market, only channel
1–11 can be operated. Selection of other channels is not possible.
The device could automatically discontinue transmission in case
of absence of information to transmit, or operational failure.
Note that this is not intended to prohibit transmission of control
or signaling information or the use of repetitive codes where
required by the technology. If this device is going to be operated
in 5.15–5.25GHz frequency range, then it is restricted to an
indoor environment only.
Important: Any changes or modifications not expressly
approved by the party responsible for compliance could
void the user's authority to operate this equipment. This
device and its antenna(s) must not be co-located or
operating in conjunction with any other antenna or
transmitter.
8
FCC Radiation Exposure Statement: This
equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment. This
equipment should be installed and operated with
minimum distance 20cm between the radiator & your
body.
Canada - Industry Canada Statement
This device complies with RSS-210.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired operation
of the device.
This device and its antenna(s) must not be co-located or
operating in conjunction with any other antenna or
transmitter.
Wireless Radio
For product available in the USA/Canada market, only
channel 1–11 can be operated. Selection of other channels is
not possible.
The device could automatically discontinue transmission in
case of absence of information to transmit, or operational
failure. Note that this is not intended to prohibit
transmission of control or signaling information or the use
of repetitive codes where required by the technology.
Important: Any changes or modifications not
expressly approved by the party responsible for
compliance could void the user's authority to operate
this equipment.
IMPORTANT NOTE:
IC Radiation Exposure Statement: This equipment
complies with IC RSS-102 radiation exposure limits
set forth for an uncontrolled environment. This
equipment should be installed and operated with
minimum distance 20cm between the radiator & your
body.
ENERGY STAR® User Information
ENERGY STAR User Information Statement: the factory
default settings of this television meet ENERGY STAR
requirements. Changing Picture Settings may increase
energy consumption, possibly beyond the limits required
for ENERGY STAR qualification.
To ensure your television is operating at optimal energy
efficiency, select [Home] mode during initial activation. To
return to [Home] mode settings, select [Standard] picture
mode. [Standard] mode is recommended for normal home
use.
ENERGY STAR
that earn the ENERGY STAR prevent
green house gas emissions by meeting
strict guidelines set by the U.S.
Environmental Protection Agency.
ENERGY STAR and the ENERGY STAR
mark are registered U.S. marks.
®
qualified TV. Products
®
Important notes about your TV
The following symptoms are technical limitations of
LCD Display technology and are not an indication of
malfunction; therefore, Toshiba is not responsible for
perceived issues resulting from these symptoms.
1)
An afterimage (ghost) may appear on t he scr een if
a fixed, non-moving image appears for a long
period of time. The afterimage is not permanent
and will disappear in a short period of time.
2)
The LCD panel contained in this TV is
manufactured using an extremely high level of
precision technology; however, there may be an
occasional pixel (dot of light) that does not operate
properly (does not light, remains constantly lit,
etc.). This is a structural property of LCD
technology, is not a sign of malfunction, and is not
covered under your warranty. Such pixels are not
visible when the picture is viewed from a normal
viewing distance.
Note: Interactive video games that involve shooting a
“gun” type of joystick at an on-screen target may not
work with this TV.
Trademark Information
powered
by
•
Cinema Series, ClearScan, Co lorStream, Dynalight,
GameTimer, Native Mode, Surflock, and Trivector are
trademarks or registered trademarks of Toshiba America
Information Systems, Inc. and/or Toshiba Corporation.
•
Android is a trademark of Google Inc.
•
Audyssey EQ® provides clear, accurate
technology ensures you enjoy your audio experience as
much as your video.
frequency monitoring to extend the range and bass of
small speakers. This enables the system to produce
lower frequencies than would be possible with a
traditional system of the same size.
consistent sound level between television progr ams,
commercials, and between the loud and soft passages of
movies.
while blocking distortion, so your TV gets loud and still
sounds great.
problems caused by small speakers and drivers.
Working together these technologies deliver a better
translation of the audio content and make the television
experience sound closer to the original.
•
Manufactured under license from Audyssey
Laboratories, Inc. U.S. and foreign patents pending.
Audyssey EQ®, Audyssey ABX™, Audyssey Dynamic
Volume®, Audyssey V olume Extension™, and
Audyssey Premium T elevision™ are r egistered and
licensed trademarks of Audyssey Laboratories, Inc.
•
Blu-ray Disc™, Blu-ray™, and the logos are trademarks
of the Blu-ray Disc Association
•
CinemaNow is a registered t radema rk of Best Buy, Inc.
•
ENERGY STAR and the ENERGY ST AR mark are
registered U.S. marks.
symbol are trademarks of Dolby Laboratories.
•
HDMI, the HDMI Logo, and High-Definition Multimedia
Interface are trademarks or registered trademarks of
HDMI Licensing LLC in the United States and other
countries.
•
MPEG Layer-3 audio coding technology licensed from
Fraunhofer IIS and Thomson.
•
Netflix is a registered trademark of Netflix, Inc.
and natural sound right out of the box. This
•
Audyssey ABX™ technology uses
sophisticated driver analysis and low
•
Audyssey Dynamic Volume®
automatically adjusts volume to provide a
•
Audyssey Volume Extension™ doubles
the volume capability in small speakers
•
Audyssey Premium T elevision™ is a suite
of technologies that remove the acoustical
•
Manufactured under license f rom Do lby
Laboratories. Dolby and the double-D
•
www.espial. com
•
Rovi is a trademark of Rovi Corporation
system is manufactured under license from Rovi
Corporation and/or its subsidiaries.
•
VUDU, Vudu Apps, and Vudu Movies are licensed and
registered trademarks of VUDU, Inc
•
YouT ube is a registered trademark of Google, Inc.
THIS PRODUCT IS LICENSED UNDER THE AVC
PA TENT PORTFOLIO LICENSE FOR THE PERSONAL
AND NONCOMMERCIAL USE OF A CONSUMER TO
(i) ENCODE VIDEO IN COMPLIANCE WITH THE AVC
STANDARD
(“AVC VIDEO”) AND/ OR (ii) DECODE AVC VIDEO
THAT W AS ENCODED BY A CONSUMER ENGAGED
IN A PERSONAL AND NON-COMMERCIAL ACTIVITY
AND/OR WAS OBTAINED FROM A VIDEO PROVIDER
LICENSED TO PROVIDE A VC VIDEO. NO LICENSE IS
GRANTED OR SHALL BE IMPLIED FOR ANY OTHER
USE. ADDITIONAL INFORMATION MA Y BE
OBTAINED FROM MPEG LA, LLC. SEE HTTP://
WWW.MPEGLA.COM
•
THIS PRODUCT IS LICENSED UNDER THE VC-1
PA TENT PORTFOLIO LICENSE FOR THE PERSONAL
AND NONCOMMERCIAL USE OF A CONSUMER TO
(i) ENCODE VIDEO IN COMPLIANCE WITH THE VC-1
STANDARD
(“VC-1 VIDEO”) AND/OR (ii) DECODE VC-1 VIDEO
THAT W AS ENCODED BY A CONSUMER ENGAGED
IN A PERSONAL AND NON-COMMERCIAL ACTIVITY
AND/OR WAS OBTAINED FROM A VIDEO PROVIDER
LICENSED TO PROVIDE VC-1 VIDEO. NO LICENSE
IS GRANTED OR SHALL BE IMPLIED FOR ANY
OTHER USE. ADDITIONAL INFORMATION MAY BE
OBTAINED FROM MPEG LA, LLC. SEE HTTP://
WWW.MPEGLA.COM
•
THIS PRODUCT IS LICENSED UNDER THE MPEG -4
VISUAL PATENT PORTFOLIO LICENSE FOR THE
PERSONAL AND NON-COMMERCIAL USE OF A
CONSUMER FOR (i) ENCODING VIDEO IN
COMPLIANCE WITH THE MPEG-4 VISUAL
STANDARD (“MPEG-4 VIDEO”) AND/OR (ii)
DECODING MPEG-4 VIDEO THAT WAS ENCODED
BY A CONSUMER ENGAGED IN A PERSONAL AND
NON-COMMERCIAL ACTIVITY AND/OR WAS
OBTAINED FROM A VIDEO PROVIDER LICENSED
BY MPEG LA TO PROVIDE MPEG-4 VIDEO. NO
LICENSE IS GRANTED OR SHALL BE IMPLIED FOR
ANY OTHER USE. ADDITIONAL INFORMATION
INCLUDING THAT RELATING TO
PROMOTIONAL,INTERNAL AND COMMERCIAL
USES AND LICENSING MAY BE OBTAINED FROM
MPEG LA,LLC. SEE HTTP:// WWW.MPEGLA.COM
The information contained in this manual, including but not
limited to any product specifications, is subject to change
without notice.
TOSHIBA CORPORATION AND TOSHIBA
AMERICA INFORMATION SYSTEMS, INC.
(TOSHIBA) PROVIDES NO WARRANTY WITH
REGARD TO THIS MANUAL OR ANY OTHER
INFORMATION CONTAINED HEREIN AND
HEREBY EXPRESSLY DISCLAIMS ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR ANY PARTICULAR PURPOSE WITH
REGARD TO ANY OF THE FOREGOING. TOSHIBA
ASSUMES NO LIABILITY FOR ANY DAMAGES
INCURRED DIRECTLY OR INDIRECTLY FROM
ANY TECHNICAL OR TYPOGRAPHICAL ERRORS
OR OMISSIONS CONTAINED HEREIN OR FOR
DISCREPANCIES BETWEEN THE PRODUCT AND
THE MANUAL. IN NO EVENT SHALL TOSHIBA BE
LIABLE FOR ANY INCIDENTAL,
CONSEQUENTIAL, SPECIAL, OR EXEMPLARY
DAMAGES, WHETHER BASED ON TORT,
CONTRACT OR OTHERWISE, ARISING OUT OF
OR IN CONNECTION WITH THIS MANUAL OR
ANY OTHER INFORMATION CONTAINED
HEREIN OR THE USE THEREOF.
This manual contains safety instructions that must be observed to avoid potential
hazards that could result in personal injuries, damage to your equipment, or loss
of data. These safety cautions have been classified according to the seriousness of
the risk, and icons highlight these instructions as follows:
Indicates an imminently hazardous situation which, if not avoided, will result
in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, could result
in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, may result
in minor or moderate injury.
Indicates a potentially hazardous situation which, if not avoided, may result
in property damage.
Provides important information.
20
Features
❖Integrated digital tuning (8VSB ATSC and QAM)—
❖1920 x 1080 output resolution.
❖Four HDMI
❖HDMI
❖HDMI
❖ColorStream
❖Digital Audio Out—Optical audio connection with Dolby
❖PC IN (Analog RGB)—Computer terminal, see “Connecting
❖Built-in WLAN—Allows the television to access your home
❖ColorMaster™—Allows you to adjust the TV’s standard
❖ClearScan
❖AutoView
❖Dynamic Volume (Audyssey Dynamic Volume
❖MediaShare (Media Player)—Allows you to view photo files
Introduction
Features
21
Eliminates the need for a separate digital converter set-top box
(in most cases).
®
—Digital, High-Definition Multimedia
Interfaces with 1080p input support
®
capabilities
ARC (Audio Return Channel)—Enables the audio signal of
the TV to be sent to an AV amplifier via an HDMI
®
cable.
RGB Range—Adjusts RGB full range signal automatically.
®
CEC Control—Allows control of external devices
from the TV remote via HDMI
®
HD—High-resolution component video input.
®
connection
®
Digital optical output format, see “Connecting a digital audio
system” on page 35.
a computer” on page 39.
from the TV.
wireless network without an external Dual Band WLAN
Adapter.
colors, see “ColorMaster™” on page 121.
®
—Provides picture clarity for fast motion video
using new Backlight Scanning technology.
®
—Allows you to automatically adjust picture
settings based on ambient light conditions and input signal
content, see “ENERGY STAR® User Information” on page 8.
®
)—
Eliminates inconsistent TV volume when changing channels or
viewing commercials, see “Audyssey Premium Television™”
on page 127.
and play music or movie files, see “ePORTAL MediaShare
(Videos, Music, and Photos)” on page 157.
22
Introduction
Overview of installation, setup, and use
❖3D capability—Allows you to view and experience 3D
content on the television while using special glasses.
❖ENERGY STAR
®
qualified
Overview of installation, setup, and use
Follow these steps to set up your TV and begin using its many
exciting features.
1Carefully read the important safety, installation, care, and
service information. Keep this manual for future reference.
2To choose a location for the TV:
❖Read “Important notes about your TV” on page 8.
❖Place the TV on the floor or a sturdy, level, stable surface
that can support the weight of the unit. Secure the TV to a
wall, pillar, or other immovable structure, see 24) on
page 4.
❖Place the TV in a location where light does not reflect on
the screen.
❖Place the TV far enough from walls and other objects to
allow proper ventilation. Inadequate ventilation may cause
overheating, which will damage the TV. THIS TYPE OF
DAMAGE IS NOT COVERED UNDER THE TOSHIBA
WARRANTY.
3Do not plug in any power cords until after you have connected
all cables and devices to your TV.
4Before connecting cables or devices to the TV, learn the
functions of the TV’s connections and controls, see “Overview
of cable types” on page 27.
5Connect your other electronic device(s) to the TV, see
“Connecting Your TV” on page 27.
6Install the batteries in the remote control, see “Installing
batteries” on page 46
7See “Using the Remote Control” on page 46 for an overview of
the buttons on the remote control.
8After connecting all cables and devices, plug in the power
cords for your TV and other devices. Then press the POWER
button on the TV control panel or remote control to turn on the
TV. If the TV stops responding to the buttons on the remote
control or TV control panel and you cannot turn the TV off or
Introduction
Brightness sensorRemote sensor
Power LED
Digital Audio
jack
2 USB ports
3 HDMI
®
ports
1 IR Blaster Out
1 Analog Audio port
TV front and side panel controls and connections
on, unplug the power cords for a few seconds and then plug
them in and try again.
9See “Navigating the menu system” on page 61 for a quick
overview of navigating the TV’s menu system.
10 Program channels into the TV’s channel memory, see “Auto
Tuning” on page 66.
11 For details on using the TV’s features, see chapters 6, 7, and 8.
12 For help, refer to “Troubleshooting” on page 181.
13 For technical specifications, see “Specifications” on page 191.
TV front and side panel controls and connections
23
(Sample Illustration) L6200U/L7200U Series front and side panel
controls and connections
receives digital audio and uncompressed digital video from an
®
HDMI
device. HDMI
device or uncompressed digital video from a DVI
®
connection is necessary to receive 1080p
signals.
TV back panel controls and connections
For explanations of cable types and connections, see “Connecting
Your TV” on page 27.
®
Digital
(Sample Illustration) L6200U/L7200U Series back panel controls
and connections
TV back panel controls and connections
Back panel controls
1POWER—Turns the TV On and Off.
2VOL +- —Adjusts the volume level. When an onscreen menu
appears, these keys function as ( / ) menu navigation
buttons.
3CH Up/Down arrow buttons—Changes the channel. When
an onscreen menu appears, these buttons function as ( /)
menu navigation buttons.
4MENU—Accesses the menu. When an onscreen menu
appears, the MENU button on the TV’s control panel functions
as the BACK button.
5INPUT—Changes the source you are viewing. When an
onscreen menu appears, the INPUT button on the TV’s control
panel functions as the OK button.
Back panel connections
6LAN IN—Connects the TV to your home network.
7PC/ColorStream HD2 IN—For use when connecting a
personal computer.
8PC/HDMI-4 (Audio) IN—PC audio input terminals are
shared with HDMI
use can be configured in the Configuring shared inputs menu,
see “Configuring shared inputs” on page 70.
9ColorStream
connections, see “Connecting DVD to ColorStream® or VCR
to composite video” on page 31.
10 Video 2 IN—Video input.
11 Video 1 IN—Video input.
12 ANT/CABLE—Antenna input that supports analog (NTSC)
and digital (ATSC) off-air antenna signals and analog and
digital Cable TV (QAM) signals.
13 HDMI
14 ARC HDMI
®
IN—High-Definition Multimedia Interface input
receives digital audio and uncompressed digital video from an
®
HDMI
device or uncompressed digital video from a DVI
device. HDMI
signals.
enables the audio signal of the TV to be sent to an AV
amplifier via the HDMI cable.
Introduction
®
-4 analog audio input terminals, and their
®
HD1 IN—These include standard A/V
®
connection is necessary to receive 1080p
®
only port—Audio Return Channel (ARC)
25
26
NOTE
Introduction
TV back panel controls and connections
15 Analog Audio OUT—Analog audio outputs for connecting an
audio amplifier.
16 Digital Audio OUT—Optical audio output in Dolby
or PCM (pulse-code modulation) format for connecting an
external Dolby
home theater system with optical audio input.
17 IR Blaster OUT—Used to connect and control infrared
remote controlled devices.
18 2 USB ports—To access video, music, or photo files with
USB device.
Component/Standard (composite) video cables carry only video
information; separate audio cables are required.
®
Digital decoder, amplifier, A/V receiver, or
®
Digital
Chapter 2
Connecting Your TV
Overview of cable types
Before purchasing cables, know the connector types your devices
require. You can purchase cables from most stores that sell
audio/video devices.
Coaxial cable (F-type)
(Sample Illustration) Coaxial cable
Coaxial (F-type) cable connects your antenna, cable TV service,
and/or cable converter box to the ANT/CABLE input on your TV.
Standard A/V cables (red/white/yellow)
(Sample Illustration) Standard AV cables
Standard A/V cables (composite video) usually come in sets of
three, and connects to video devices with analog audio and
composite video output. These cables (and the related inputs on
your TV) are typically color-coded according to use: yellow for
27
28
NOTE
NOTE
Connecting Your TV
Overview of cable types
video, red for stereo right audio, and white for stereo left (or mono)
audio.
Component video cables (red/green/blue)
(Sample Illustration) Component video cables
Component video cables come in sets of three and are for use with
video devices with component video output. (ColorStream
Toshiba’s brand of component video.) These cables are typically
color-coded red, green, and blue. Separate audio cables are required
for a complete connection.
Component video cables provide better picture quality than
composite video cables.
HDMI® cable (with HDMI Logo)
(Sample Illustration) HDMI® cable
®
HDMI
devices that have an HDMI
digital audio and video in its native format. Separate audio cables
are not required, see “Connect a computer to the TV’s HDMI®
terminal” on page 41.
(High-Definition Multimedia Interface) cable connects to
HDMI® cables provide the best audio and picture quality.
®
®
output. An HDMI® cable delivers
is
Dual-wand IR blaster cable
NOTE
Connect the dual-wand IR blaster cable to the IR blaster terminal to
control infrared remote controlled devices from the TV.
Optical audio cable
(Sample Illustration) Optical audio cable
Optical audio cable connects receivers with Dolby
(pulse-code modulation) optical audio input to the TV’s Digital Audio Out terminal, see “Connecting a digital audio system” on
page 35.
Analog RGB (15-pin) computer cable
(Sample Illustration) Analog RGB (15-pin) computer cable
Analog RGB (15-pin) computer cable connects a computer to the to
the TV’s PC IN terminal, see “Connecting a computer to the TV’s
PC IN terminal:” on page 40.
Connecting Your TV
Overview of cable types
®
Digital or PCM
29
Separate audio cables are required.
3.5mm Stereo to RCA Y-cable
(Sample Illustration) 3.5mm Stereo to RCA Y- cable
3.5mm Stereo to RCA Y-cable connects an audio signal from DVI
device to TV.
LAN cable
(Sample Illustration) LAN cable
Standard LAN cable connects the TV to your home network, see
“Connecting the TV to a home network with an Internet connection
- wired” on page 44.
30
HDMI 3HDMI 3
COLOR COLOR
STREAM STREAM
HD 1HD 1
VIDEO 2VIDEO 2
IN
OUT
CH 3
CH 4
VIDEO
OUT
AUDIO
OUT
COMPONENT VIDEO
L
R
Satellite
IN
P
B
P
R
Y
TV back panel
VHF/UHF
Antenna
Cable TV
Satellite receiver with component video
Satellite dish
Coaxial cable
Component
video cable
Standard audio
cable
AV Component adapter
cable (supplied)
Cable box
NOTE
Connecting an antenna, satellite receiver, and cable TV box
Crossover LAN cable connects the TV directly to a computer, see
“Connecting the TV directly to a computer without an Internet
connection” on page 43.
About the connection illustrations
Connecting Your TV
You can connect different types and brands of devices to your TV
in several different configurations. The connection illustrations in
this manual are representative of typical device connections only.
The input/output terminals on your devices may differ from those
illustrated herein. For details on connecting and using your specific
devices, refer to each device’s owner’s manual.
Connecting an antenna, satellite receiver, and cable TV box
(Sample Illustration) L6200U/L7200U Series—Connecting to an
antenna, satellite receiver, and cable TV box
Items needed:
❖Coaxial cables
❖Standard AV cables
❖Component video cables (red/green/blue)
When you use a cable box, you may not be able to use the remote
control to program or access certain features on the TV.
To view the antenna or cable signal:
Select ANT/CABLE video input source on the TV.*
To view basic and premium cable channels:
Select the ANT/CABLE video input source on the TV.* Tune the
TV to channel 3 or 4 (whichever channel the cable box output is set
to). Use the cable box controls to change channels.
Loading...
+ 176 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.