OWNER'S MANUAL
LCD Color TV
42WL68A
42WL68E
42WL68T
Owner's Record
You will find the model number and serial number on
the back of the TV. Record these numbers in the spaces
provided below. Refer to them whenever you call upon
your TOSHIBA dealer regarding this product.
Model number:
Serial number:
Contents
Introduction
Welcome to Toshiba . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . 3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Important information. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Getting started
Connecting an antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Exploring your new TV . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installing the remote control batteries . . . . . . . . . . . . 7
TV top, front and side panel controls . . . . . . . . . . . . . . . . 8
TV back panel connections. . . . . . . . . . . . . . . . . . . . . . . . 9
Learning about the remote control . . . . . . . . . . . . . . . . . 10
Location of controls . . . . . . . . . . . . . . . . . . . . . . . . . 10
Learning about the menu system . . . . . . . . . . . . . . . . . . 10
Displaying the menu chart . . . . . . . . . . . . . . . . . . . . 11
Turning the TV on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Switching on the TV . . . . . . . . . . . . . . . . . . . . . . . . 11
Switching off the TV . . . . . . . . . . . . . . . . . . . . . . . . 11
Watching TV programs . . . . . . . . . . . . . . . . . . . . . . . . . 12
Selecting the menu language . . . . . . . . . . . . . . . . . . 12
Changing the program position . . . . . . . . . . . . . . . . 12
Switching between two program positions . . . . . . . 12
Displaying the on-screen information . . . . . . . . . . . 12
Programming channels into the TV’s channel memory . 12
Programming channels automatically . . . . . . . . . . . 12
Manually setting channels in the channel memory . 13
Sorting program position . . . . . . . . . . . . . . . . . . . . . 13
Using the TV’s features
Picture adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Selecting the picture size . . . . . . . . . . . . . . . . . . . . . 14
Using the picture still . . . . . . . . . . . . . . . . . . . . . . . . 15
Adjusting the picture position . . . . . . . . . . . . . . . . . 15
Resetting the picture position. . . . . . . . . . . . . . . . . . 15
Selecting the picture mode . . . . . . . . . . . . . . . . . . . . 15
Adjusting the basic picture quality. . . . . . . . . . . . . . 15
Activating the black stretch . . . . . . . . . . . . . . . . . . . 16
Activating the MPEG NR (Noise Reduction) . . . . . 16
Activating the DNR (Digital Noise Reduction) . . . . 16
Selecting the color temperature . . . . . . . . . . . . . . . . 16
Adjusting the color management . . . . . . . . . . . . . . . 16
Resetting the base color adjustment . . . . . . . . . . . . . 16
Using the active backlight control . . . . . . . . . . . . . . 16
Using the cinema mode . . . . . . . . . . . . . . . . . . . . . . 17
Using the meta brain PRO 100. . . . . . . . . . . . . . . . . 17
Sound adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Setting the MTS (Multi-channel TV Sound) . . . . . . 17
Selecting the dual 1 or dual 2 mode . . . . . . . . . . . . . 17
Selecting the stereo programs . . . . . . . . . . . . . . . . . 18
Selecting the bilingual programs . . . . . . . . . . . . . . . 18
Adjusting the sound quality . . . . . . . . . . . . . . . . . . . 18
Using the SRS WOW surround sound . . . . . . . . . . . 18
Using the stable sound . . . . . . . . . . . . . . . . . . . . . . . 18
Activating the speaker . . . . . . . . . . . . . . . . . . . . . . . 18
Selecting the woofer internal/external mode . . . . . . 19
Using the bass boost. . . . . . . . . . . . . . . . . . . . . . . . . 19
Using an external woofer system . . . . . . . . . . . . . . . 19
Selecting the audio output . . . . . . . . . . . . . . . . . . . . 19
Other features settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Selecting the timer menu. . . . . . . . . . . . . . . . . . . . . . 19
Using the auto format . . . . . . . . . . . . . . . . . . . . . . . . 20
Activating blue screen. . . . . . . . . . . . . . . . . . . . . . . . 20
Adjusting the brightness of side panel . . . . . . . . . . . 20
Selecting the video input source to view. . . . . . . . . . . . . 20
Setting the manual setting menu . . . . . . . . . . . . . . . . 21
Teletext . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Setting up the teletext mode . . . . . . . . . . . . . . . . . . . 21
Adjusting the teletext SW . . . . . . . . . . . . . . . . . . . . . 21
Teletext general information. . . . . . . . . . . . . . . . . . . 22
Using Auto mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Using LIST mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Teletext buttons on the remote control . . . . . . . . . . . 23
Using the double-window . . . . . . . . . . . . . . . . . . . . . . . . 23
Displaying the double-window . . . . . . . . . . . . . . . . . 23
Selecting the headphone mode . . . . . . . . . . . . . . . . . 24
Adjusting the headphone volume (Mode 2) . . . . . . . 24
Using a headphone . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Connecting your TV
Side connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Connection example . . . . . . . . . . . . . . . . . . . . . . . . . 25
Back connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Connection example . . . . . . . . . . . . . . . . . . . . . . . . . 25
Connecting an HDMI and a DVI device . . . . . . . . . . . . . 26
Connecting an HDMI and a DVI device. . . . . . . . . . 26
Connecting an HDMI device . . . . . . . . . . . . . . . . . . 26
Connecting a DVI device . . . . . . . . . . . . . . . . . . . . . 26
Selecting the PC/HDMI audio mode. . . . . . . . . . . . . . . . 27
Setting the HDMI1 audio mode . . . . . . . . . . . . . . . . . . . 27
Connecting a computer . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Using the PC setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Adjusting the picture size/position . . . . . . . . . . . . . . 28
Adjusting the clock phase of the picture . . . . . . . . . . 28
Adjusting the sampling clock . . . . . . . . . . . . . . . . . . 28
Resetting the PC setting . . . . . . . . . . . . . . . . . . . . . . 28
Reference section
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Symptom and solution . . . . . . . . . . . . . . . . . . . . . . . 29
Broadcast system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Broadcast transmission systems of each country or
region . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
LCD color television. . . . . . . . . . . . . . . . . . . . . . . . . 30
2
Introduction
Welcome to Toshiba
• Thank you for purchasing this Toshiba LCD Color
Television. This manual will help you use the exciting
features of your new TV.
• Instructions in this manual are based on using the remote
control.
• You also can use the controls on the TV if they have the
same name as those referred to on the remote control.
• Please read all safety and operating instructions in this
manual carefully, and keep this manual for future reference.
Important Safety Instructions
Be sure to observe the following instructions and precautions
to ensure safe use of this TV.
Installation
1) Always connect the power plug to an appropriate
electrical outlet equipped with A model: 220-240V,
AC 50Hz, E model: 220-240V, AC 50/60Hz and T
model: 110-240V, AC 50/60Hz.
Never use the TV outside the specified voltage range. It
may cause a fire or an electric shock.
WARNING ABOUT THREE-WIRE GROUNDINGTYPE PLUG:
• This product shall be connected to a main socket
outlet with a protective earthing connection.
• Never remove the earthing pin on the power plug.
This system is equipped with a three pin earthingtype power plug. This plug will only fit an earthingtype power outlet. This is a safety feature. If you are
unable to insert the plug into the outlet, contact an
electrician to replace the wall outlet.
• Never defeat the purpose of the earthing plug.
Ex. 220-240V AC, 50/60Hz
3) Never place the TV in an unstabilized location such
as on a shaky table, incline or location subject to
vibration.
The TV may drop or fall off which may cause an injury
or damage.
4) Never block or cover the slots and openings in the
cabinet.
• Never place the TV so that it is facing upward or on
its side.
• Never place the TV in a closet, bookcase or other
similar area where the ventilation is poor.
• Never drape a newspaper, tablecloth or curtain on the
TV.
• When installing the TV against a wall, always keep
the TV at least 10 cm away from the wall.
• Never place the TV on a soft unstable surface, such
as a carpet, or a cushion.
The inside of this TV will overheat if the ventilation holes
are covered, blocked or sealed, which may result in a
fire.
5) Never place the TV near a heater or in direct
sunlight.
The surface of the cabinet or power cord may melt and
result in a fire or an electric shock.
Check!
About the fuse
In a three pin earthing-type, the fuse fitted in this plug is
approved by ASTA or BSI to BS1362. It should only be
replaced by a correctly rated and approved type and the
fuse cover must be refitted.
2) Never insert or remove the power plug with wet
hands.
This may cause an electric shock.
6) Never place the TV in an area exposed to high
humidity levels, such as in a bathroom or close to a
humidifier.
This may cause a fire or an electric shock.
3
Introduction
7) Never place the TV next to a stove where it will be
exposed to oil, smoke, or steam, or in a location
where there is a large quantity of dust.
This may cause a fire or an electric shock.
8) Install the TV in a horizontal, stable location.
Connect between two clips on the back of the TV
and a wall, pillar, etc., with a sturdy tie and clip of
supplied accessories (- page 30).
• Use as short a tie as possible to ensure the TV is
stable.
• If the TV is not installed securely, it may lean or fall
over and cause an injury.
• To prevent injury, use the exclusive optional stand or
wall-hanging bracket to install this TV on the floor or
wall securely in accordance with a qualified
technician.
Sturdy tie
(as short as possible)
10) Precautions for installing on outdoor antenna
An outside antenna system should not be located in the
vicinity of overhead power lines, or other electric light or
power circuits.
If the antenna falls down or drops, it may cause an injury
or an electric shock.
Use
1) Never place hot objects or open flame sources,
such as lighted candles or nightlights, on or close
to the TV.
High temperatures can melt plastic and lead to fires.
Clip
Clip
Side view op view
T
9) Precautions for moving the TV
• When moving the TV, be sure to remove the plug
from the wall outlet and disconnect the antenna cable
and audio/video cables, any steady ties. A fire or an
electric shock may result if the power cord is
damaged.
• When carrying the TV, at least two people are
needed. Be sure to carry it upright.
• Never carry the TV with the screen facing up or down.
Clip
2) The apparatus shall not be exposed to dripping or
splashing and that no objects filled with liquids,
such as vases, shall be placed on the apparatus.
When liquids are spilled or small items are dropped
inside the TV, this may cause a fire or an electric shock.
If small objects drop inside the TV, turn off the TV and
remove the power plug from the outlet immediately and
contact a service technician.
3) Never insert objects (metal or paper) or pour water
inside the TV through ventilation holes and other
openings.
These items may cause a fire or an electric shock.
If these objects are inserted inside the TV, turn off the
TV and remove the power plug from the outlet
immediately and contact a service technician. Be
especially careful that children do not insert objects in
the TV.
Clip
4
Introduction
4) Never stand or climb on the TV.
Be especially careful in households with children to
prevent them through climbing on top of the TV.
It may move, fall over, break, become damaged or
cause an injury.
5) When the TV will not be used for a long period of
time, such as during vacation or travel, remove the
power plug from the wall outlet for safety.
• The TV is not completely disconnected from the
power supply line, as minute current is consumed
even when the ! Power switch is turned off.
• The Mains plug or an appliance coupler is used as the
disconnect device, therefore the disconnect device
shall remain readily operable.
6) Never pull on the power cord when removing the
plug from the wall outlet.
Always hold the plug firmly when removing it. If the
power cord is yanked, the cord may become damaged
and a fire or an electric shock may occur.
8) If there is thunder or lightning, never touch the
antenna cable or other connected cables.
You may suffer an electric shock.
Service
1) Never repair, modify or disassemble the TV by
yourself.
It may cause a fire or an electric shock. Consult a
service technician for inspection and repairs.
2) When a malfunction occurs, or if smoke or an
unusual odor comes from the TV, turn off the TV
and remove the power plug from the outlet
immediately.
Make sure that the smoke or smell has stopped, then
contact a service technician. If the TV is still used in this
condition, it may cause a fire or an electric shock.
7) Never cut, break, modify, twist, bunch up or bent the
cord or apply excessive force or tension to it.
Never place heavy objects on the cord or allow it to
overheat as this may cause damage, a fire or an electric
shock. Contact a service technician if the power cord is
damaged.
3) If the TV is dropped or the cabinet is broken, turn off
the TV and remove the power plug from the outlet
immediately.
If the TV is still power used in this condition, it may
cause a fire or an electric shock. If the cabinet is broken,
be careful when handling the TV to prevent an injury.
Contact a service technician for inspection and repair.
5
Introduction
4) When the TV reaches the end of its useful life, ask a
qualified service technician to properly dispose of
the TV.
Note:
The lamp unit contains a small amount of mercury.
Disposal of mercury may be regulated due to
environmental considerations.
Dispose of the used lamp unit by the approved method
for your area. For disposal or recycling information,
please contact your local authorities.
Cleaning
1) Remove the power plug before cleaning.
Never use solvents such as benzine or thinner to clean
the TV.
• These solvents may distort the cabinet or damage its
finish.
• If rubber or vinyl products remain in contact with the
TV for a long time, a stain may result.
If the cabinet becomes dirty, clean it with a soft, dry
cloth.
When cleaning the surface of the LCD display, wipe the
panel surface gently with a soft, dry cloth.
Important information
1) About LCD screen
• If you have the LCD screen facing to the sun, the LCD
screen will be damaged. Be aware of locating the TV
in the place such as window side or outside of the
room.
• Never press the LCD screen strongly or scratch it,
and never put anything on it. These actions will
damage the LCD screen.
2) About cabinet
Never spray volatile compounds such as insecticide on
the cabinet.
This may cause a discoloration or damage the cabinet.
3) Some pixels of the screen do not light up
The LCD display panel is manufactured using an
extremely high level of precision technology, however
sometimes some pixels of the screen may be missing
picture elements or have luminous spots. This is not a
sign of a malfunction.
4) About Interference
The LCD display may cause interference in image,
sound, etc. of other electronic equipment that receives
electromagnetic waves (e.g. AM radios and video
equipment).
5) About using under the low temperature places
If you use the TV in the room of 0°C or less, the picture
brightness may vary until the LCD monitor warms up.
This is not a sign of a malfunction.
2) Periodically disconnect the power plug from the
outlet and check it.
If dust has collected on the power plug connectors,
clean off the dust with a dry cloth.
This dust may cause a fire due to reduced insulation on
the plug.
Clean here
6) About afterimage
If a still picture is displayed, an afterimage may remain
on the screen, however it will disappear.
This is not a sign of malfunction.
Exemptions
• Toshiba is not liable for any damage caused by fires, natural
disaster (such as thunder, earthquake, etc.), acts by third
parties, accidents, owner’s misuse, or uses in other improper
conditions.
• Toshiba is not liable for incidental damages (such as profit
loss or interruption in business, modification or erasure of
record data, etc.) caused by use or inability to use of product.
• Toshiba is not liable for any damage caused by neglect of
the instructions described in the owner’s manual.
• Toshiba is not liable for any damage caused by misuse or
malfunction through simultaneous use of this product and
the connected equipment.
6
Getting started
Connecting an antenna
Optimum reception of color requires a good signal and will
generally mean that an outdoor antenna must be used.
The exact type and positioning of the antenna will depend upon
your particular area.
Your Toshiba dealer or service personnel can best advise you
on which antenna to use in your area.
Before connecting the antenna cable, turn off all main power
switches.
VHF and/or
UHF antenna
Media Recorder
IN
OUT
Antenna cable (75 7 coaxial)
(not supplied)
300 7 twin-lead feeder
TV back view
Exploring your new TV
Installing the remote control batteries
Remove the battery cover.
Insert two R03 (AAA) batteries matching the –/+ polarities of
the battery to the –/+ marks inside the battery compartment.
Cautions:
• Dispose of batteries in a designated disposal area. Never
throw batteries into a fire.
• Attention should be drawn to the environmental aspects of
battery disposal.
• Never mix battery types or combine used batteries with new
ones.
Notes:
• If the remote control does not operate correctly, or if the
operating range becomes reduced, replace both batteries
with new ones.
• If the batteries are dead or if you will not use the remote
control for a long time, remove the batteries to prevent
battery acid from leaking into the battery compartment.
Antenna adaptor
(not supplied)
75 7 coaxial cable
Plug
(not supplied)
75 7
antenna
terminal
75 7 antenna
terminal
Effective range
within 5 m
7
Getting started
TV top, front and side panel controls
• You can operate your TV using the buttons on the side panel or the remote control. The back and side of the panel provide the
terminal connections to connect other equipment to your TV (- “Connecting your TV” pages 25, 26, 27).
• For the use of each control, see the pages in brackets.
TV top view
TV front view
1
You can swivel the TV screen.
Swivel angle:
15 degrees to left and right.
Right side view
2
4
3
Control panel
5
6
7
8
9
10
Headphones
(Not supplied)
11
1 ! (Power switch) — Press to turn the TV on and off
(- page 11).
2 4 (Timer LED) — Timer indicator (- page 19).
3 ! (Power LED) — Power indicator (- page 11).
4 (Remote sensor) — Point the remote control toward
this remote sensor (- page 7).
5 1 (Power on/Standby) — Press to turn the TV on/
standby (- page 11).
6 pBb (Program position) — When no menu is on-
screen, these buttons select the program position.
(- page 12).
Uu (MENU up/down) — When a menu is on-screen,
these buttons function as up/down menu navigation
buttons (- page 10).
7 2 – + (Volume) — When no menu is on-screen, these
buttons adjust the volume level (- page 10).
I i (MENU left/right) — When a menu is on-screen,
these buttons function as left/right menu navigation
buttons or adjust settings (- page 10).
8 MENU — Press to access the menu system (- page 10).
9 o (Input source selection) — When no menu is on-
screen, this button selects the input source (- page 20).
OK — When a menu is on-screen, this button functions
as the next menu navigation button (- page 10, 20).
10 o (2) (Video 2 input terminals) — Optional S-video
or standard video and standard audio inputs (- page 25).
11 D (Headphone jack) — For use with headphones.
8
TV back panel connections
Getting started
12
13
14
15
16 17
18
TV back view
*
You can use the cable holder
to hold antenna cable, video
and audio cables etc.
When moving the TV, never
hold this holder.
Power cord
Cable holder*
19 20 21 22
12 o (C1) (COMPONENT VIDEO INPUT terminals)
—High-definition component video and standard audio
inputs (- page 25).
13 o (1) (Video 1 input terminals) — Optional S-video
or standard (composite) video and standard (analog)
stereo audio inputs (- page 25).
14 o (C2) (COMPONENT VIDEO INPUT terminals)
— High-definition component video and standard audio
inputs (- page 25).
15 O MONITOR (output terminals) — Standard video
and standard audio outputs (- page 25).
16 O WOOFER (output terminal) — For use when
connecting woofer system (variable) (- page 25).
17 O AUDIO (output terminals) — Standard audio
outputs (fixed/variable) (- page 25).
18 o PC/HDMI1 (AUDIO) (input terminals) — For use
when connecting a personal computer (PC) or a DVI
device with standard audio output (- page 26, 27).
19 A (Antenna input terminal) — Analog antenna signal
input (- page 7).
20 o RGB/PC (input terminal) — For use when
connecting a personal computer (PC) (- page 27).
21 o HDMI1 (input terminal) — High-Definition
Multimedia Interface input receives digital audio and
uncompressed digital video from an HDMI device or
uncompressed digital video from a DVI device (- page
26).
22 o HDMI2 (input terminal) — High-Definition
Multimedia Interface input receives digital audio and
uncompressed digital video from an HDMI device
(- page 26).
9
Getting started
Learning about the remote control
Location of controls
• CALL (- pages 12, 13)
• Initial/index function for Teletext
(- page 23)
Number buttons (0-9)
(- pages 12, 19)
To return to the previous program
(- page 12)
Picture size selection
(- page 14)
• MENU
• DVD Menu
OK (- page 20)
• Menu left/right (- page 11)
• Volume – +
(These buttons adjust the volume level.)
Double-window picture/sound
selection (- page 23)
Double-window on/off (- page 23)
Mode switch
o contr
TV : T
STB : To control Set Top Box
DVD : To control DVD
Stereo/bilingual selection
(- page 18)
When in STB or DVD mode:
(Only for Toshiba DVD players)
V
W / w
c
CC
cc
X
v
Z
z
: to OPEN/CLOSE
: to STILL/STEP
: to PLAY
: to REWIND
: to FAST FORWARD
: to SLOW
: to STOP
: to SKIP-REWIND
: to SKIP-FORWARD
ol TV
Power on/Standby
(- page 11)
• Input source selection
(o1, o2, oC1, oC2, HDMI1,
HDMI2, PC) (- page 20)
• To access sub-pages
when in teletext (- page 22)
Picture mode selection (- page 15)
EXIT (- page 11)
• Menu down/up (- page 11)
• Program position Bb (- page 12)
• Teletext Bb (- page 22)
Picture still (- page 15)
• Bass boost on/off (- page 19)
• External woofer on/off (- page 19)
Sound mute
(This button turns off/on the sound.)
When in Teletext mode:
E : •
•
mode and a normal broadcast
picture mode)
(- pages 22, 23)
A :
B :
C : To enlarge teletext display size
(- page 23)
D : To select a page while viewing
a normal picture (- page 23)
When in TV mode:
D : To select the time display
(- page 23)
Teletext control buttons
(Four colored buttons: Red, Green,
Yellow, Blue) (- page 22)
Teletext on/off
Text media mode (The teletext
To reveal concealed text (- page 23)
To hold a wanted page (- page 23)
Learning about the menu system
We suggest you familiarize yourself with the display charts before using the menu system:
•Press M to display menu, then press Y or y to select main menu headings.
•Press < or > to select an item.
•Press Y or y to select or adjust setting.
•Press Q to display the next menu.
10
Getting started
Displaying the menu chart
PICTURE
menu
Picture settings
Color management
Base color adjustment
Active Backlight Control
Cinema mode
meta brain PRO 100
MENU
SOUND
menu
MTS
Dual
Headphone
Headphone level
Bass
Treble
MENU
SET UP
menu
Language
Auto tuning
Manual tuning
AV connection
Picture position
MENU
PICTURE
EXIT
Back Watch TV
SOUND 1/ 2
EXIT
Back Watch TV
SET UP
EXIT
Back Watch TV
OK
Off
On
On
On
Auto
Dual 1
Mode 1
0
0
English
OK
OK
OK
OK
Picture settings
Color management
Base color adjustment
Active Backlight Control
Cinema mode
meta brain PRO 100
MENU
Balance
WOW
Stable sound
Speaker
MTS
Dual
Headphone
Headphone level
Bass
Treble
MENU
Language
Auto tuning
Manual tuning
AV connection
Picture position
MENU
PICTURE
EXIT
Back Watch TV
SOUND 2/ 2
SOUND 1/ 2
EXIT
Back Watch TV
SET UP
EXIT
Back Watch TV
OK
Off
On
On
On
Auto
Dual 1
Mode 1
0
0
English
OK
OK
OK
OK
• In the 480i or 576i input signals mode, you can select the
Cinema mode in the PICTURE menu (
• When you use the color management function (
- page 17).
- page 16),
you can select the Base color adjustment in the PICTURE
menu.
• When you use the double-window function (
- page 24),
you can select the Headphone level in the SOUND menu.
Turning the TV on
0
OK
Off
On
Switching on the TV
Connect the power cord to a wall outlet.
1 Press ! on the TV left side until it clicks.
1
The ! Power indicator lights in green. Press
remote control or 1 on the TV right side panel if the !
Power indicator lights in red.
Note:
If you watch black and white programs when the color system
mode is set to Auto, color noise may appear on the screen. In
this case select the appropriate Color system (For the system
of each country or region, refer to pages 13 and 29).
Mono
J on the
TIMER
menu
Sleep timer
On timer
On timer Position
MENU
Back Watch TV
FUNCTION
menu
Teletext
Teletext SW
Auto format
Blue screen
Side panel
MENU
Back Watch TV
TIMER
EXIT
FUNCTION
EXIT
00:00
00:00
01
Auto
On
On
Sleep timer
On timer
On timer Position
MENU
Teletext
1
1
Teletext SW
Auto format
Blue screen
Side panel
MENU
TIMER
EXIT
Back Watch TV
FUNCTION
EXIT
Back Watch TV
00:00
00:00
01
Auto
1
On
On
1
Notes:
• In the video input mode (o1, o2), Auto tuning and Manual
tuning are not available. Instead, Manual setting appears
in the SET UP menu (
- page 21).
• If you connect external equipment via component video
source to external input, Color system selection in the
Manual setting menu is not available.
• If you do not make a selection for a while, the menu display
disappears automatically.
• If you want to close the menu display instantly, press P.
• To return to the previous menu, press M.
• In the PC input mode, PC Setting appears in the SET UP
- page 28).
menu (
Switching off the TV
1
Press J on the remote control or 1 on the TV right side
panel to switch to the standby mode.
2 To switch the TV off, press ! on the TV left side.
Power indicator will be turned off.
Notes:
• This TV is not fully disconnected from the main supply, as
minute current is consumed even when ! is turned off.
When the TV will not be used for a long period of time, such
as during vacation or travel, remove the power plug from the
wall outlet.
• The TV will automatically turn itself off after approximately 15
minutes if it is tuned to a vacant channel or a station that
completes its broadcast for the day. This function does not
work in external input or Blue screen Off mode.
The TV will automatically turn itself off after approximately 2
hours if you do not operate the TV after turned on by on timer
function.
• If power is cut off while you are viewing the TV, the Last
Mode Memory function turns on the TV automatically when
power is applied again. If power is going to be off for a long
time and you are going to be away from your TV, unplug the
power cord to prevent the TV from turning on in your
absence.
11
Getting started
Watching TV programs
Selecting the menu language
Choose from 9 different languages (English, Chinese (CS),
Malay, Thai, Vietnamese, Russian, Arabic, Persian or French)
for the on-screen display.
1 Press M, then press Y or y to display SET UP menu.
2 Press < or > to select Language.
3 Press Y or y to select the desired language.
Language
Auto tuning
Manual tuning
AV connection
Picture position
MENU
SET UP
EXIT
Back Watch TV
Changing the program position
1
Enter the desired program position number using the
Number buttons on the remote control.
For program positions below 10, use 0 and the required
number e.g., for program position 1.
2 You can also change the program position by using > or
<.
The program position will be displayed on the screen with
the Mono/Stereo/Dual audio status.
Note:
The program position selection change between different
format channels takes several seconds.
Switching between two program positions
You can switch two program positions without entering actual
position number each time.
1 Select the first program position you want to view.
2 Select the second program position with the Number
buttons (0-9).
3 Press :. The previous channel will be displayed.
Each time you press :, the TV will switch back and forth
between the two program positions.
English
OK
OK
OK
OK
Displaying the on-screen information
1
Press K to display the following on-screen
information.
ABCD4
Stereo
The information will disappear in 6 seconds.
• Program position or external input mode selected
• Program skip on/off information
• Label (if set)
• Mono/Stereo/Dual audio status
2 To erase the display instantly, press K again.
Programming channels into the
TV’s channel memory
• First, use the Auto tuning function to preset all the active
channels in your area automatically. Then, arrange the
preset channels with the Manual tuning function so that you
can tune into only desired channels.
• Use the Manual tuning operation if desired channels cannot
be preset with the Auto tuning or if you would like to preset
channels to specific position numbers one by one.
Programming channels automatically
1
From the SET UP menu, press < or > to select Auto
tuning.
2 Press Q to display the Auto tuning menu.
Press OK key to start.
!
EXIT for no change.
MENU
3 Press Q to start the automatic search.
The search will begin for all available stations.
Searching
Pos :2
EXIT
The slide bar will move along the line as the search
progresses.
If you make a mistake, simply repeat steps 1-3 to start
again from the beginning.
4 When the automatic search is completed, the TV will
automatically return to the first program position.
5 Press > or < to view the programmed position.
Note:
When you preset the program channel which sound of
broadcast transmission system adopts “M” system, the sound
system may not be tuned correctly if the radio waves transmit
badly. At that time, preset the channel by Manual tuning.
The countries such as Myanmar, Brazil, Chile, Colombia apply
to this case. See page 29 for more details.
Auto tuning
EXIT
Back Watch TV
Auto tuning
Stop
12
Getting started
Manually setting channels in the channel
memory
1
From the SET UP menu, press < or > to select
Manual tuning.
2 Press Q to display the Manual tuning menu.
Press < or > to select the program position you want to
arrange.
Prog. Label
OK
MENU
Manual tuning
1
2
3
4
5
6
Select
Back Watch TV
EXIT
Sort
3 Press Q to display the breakdown menu.
Press Y or y to select an item, then press < or > to
select the item as shown below.
Manual tuning
Program
A
1
B/G
OK
Store
MENU
Back Watch TV
ACE
BDF H
A. Program position selection
B. Sound system (- page 29)
C. Color system (- page 29)
A : Automatic (factory set), P : PAL, S : SECAM
N4 : NTSC 4.43 (MHz), N3 : NTSC 3.58 (MHz)
If the color of a certain channel is abnormal, the
automatic color system selection (A) may have
malfunctioned, or sound system selection is wrong. In
such a case, select another color and/or sound system
(- page 29).
D. Program position skip selection
Press < or > to turn the program position skip
option on “8” or off “(”.
The program position will then be skipped when you
select channels with > or <.
The “8” mark will appear beside a program position
number when you use the Number button on the
remote control.
E. Channel search operation
Press > to search up the band or < to search down
the band.
Press < or > repeatedly until your desired channel is
displayed.
When a station/satellite is found, it will be displayed.
NEVER PRESS ANY OTHER BUTTONS WHILE
THE SET IS TUNING.
F. Auto Fine Tuning
Press < or > to turn the Auto Fine Tuning option on
“9” or off “0”.
The Auto Fine Tuning function automatically corrects
slight fluctuations when receiving signals.
Manual Fine Tuning
While the Auto Fine Tuning turn off “0”, press < or
> so that the better picture and sound are obtained.
EXIT
G
G. ANT ATT (Antenna attenuator)
Press <
or >
to turn the ANT ATT option on “&”
or off “6”, when visual interference occurs, set the
ANT ATT to on.
H. Label
Station labels appear under the program position
display each time you turn on the TV, select a channel,
or press K.
To change or create station labels:
1) Press < or > repeatedly to select a character for
the first space, then press y.
*(blank space)
2) Repeat step 1) to enter the rest of the characters. If
you would like a blank space in the label name, you
must choose a blank space from the list of
characters.
Press Q to store your settings.
Sorting program position
• The TV is capable of receiving a number of different
channels depending upon where you live.
• Sorting program position is an easy way of storing each
channel on the program position of your choice.
Ex.: To swap channel ABCD (Prog.1) for channel MNOP
(Prog.4):
1 From the SET UP menu, press < or > to select
Manual tuning menu, then press Q.
2 Press < or > to select the channel ABCD, then press y.
Prog. Label
OK
MENU
Manual tuning
1
2
3
4
5
6
Select
Back Watch TV
EXIT
ABCD
EFGH
IJKL
MNOP
Sort
3 Press < to select the new position “4”, then press Y.
Prog.
MENU
Manual tuning
Label
EXIT
EFGH
IJKL
MNOP
1
2
3
4
5
6
Store
Back Watch TV
ABCD
4 Press > to select the channel MNOP, then press y.
5 Press > to select the new position “1”, then press Y.
6 Confirm new Manual tuning menu.
Prog. Label
OK
MENU
Manual tuning
EXIT
MNOP
EFGH
IJKL
ABCD
1
2
3
4
5
6
Select Sort
Back Watch TV
13
Using the TV’s features
Picture adjustment
Selecting the picture size
1
Press and hold O until the picture size list appears on the
screen, then press < or > to select the appropriate
picture size (or press O repeatedly to select required
picture size directly).
The antenna input signal
Wide
Super Live 2
Cinema 2
4:3
Super Live 1
Cinema 1
Subtitle
14:9
2 Press Q.
Super Live 1
When receiving “4:3 format” signal, this setting will enlarge
the image to fit the screen by stretching the image vertically
and horizontally, holding the better proportions at the center of
the image.
Wide
Use this setting when watching a wide-screen DVD, widescreen video tape or a 16:9 broadcast (when available). Due to
the range of wide-screen formats (16:9, 14:9, 20:9 etc.), you
may see bars on the top and bottom of the screen.
Super Live 2
When receiving “side panel format” signal, this setting will
enlarge the image to fit the screen by stretching the image
vertically and horizontally, holding the better proportions at
the center of the image. Also the black bars on the both sides
of the screen will eliminate or reduce.
Cinema 2
When watching “all sides panel format” films/video tapes, this
setting will eliminate or reduce the black bars on all the sides
of the screen by zooming in and selecting the image without
distortion.
Cinema 1
When watching “letterbox format” films/video tapes, this
setting will eliminate or reduce the black bars at the top and
bottom of the screen by zooming in and selecting the image
without distortion.
Subtitle
When subtitles are included on a letterbox format broadcast,
this setting will raise the picture so that the most of text is
displayed.
Subtitle
14:9
Use this setting when watching a 14:9 broadcast.
4:3
Use this setting to view a true 4:3 broadcast.
Notes:
• Using the special functions to change the size of the
displayed image (e.g. changing the height/width ratio) for
the purpose of public display or commercial gain may
infringe on copyright laws.
• If the aspect ratio of the selected format is different from the
one of the TV transmission or video program, it can cause a
difference in vision. Change to the correct aspect ratio
picture size.
• In the PC input mode (- page 20), the picture size
selection is wide, PC media window (PC and a normal
broadcast signal) or normal only.
• In the 1080i or 720p input signal mode, the picture size
selections are Super Live 1, Cinema 1, Wide, Super Live
2, Cinema 2 and 4:3.
14
Using the TV’s features
Using the picture still
•Press R to freeze the picture.
Even if an image is frozen on the TV screen, the pictures are
running on the input source. Audio continues to be output as
well.
To return to a moving picture, press R again.
(Moving) (Still)
Notes:
• If you use this function except for the purpose of your private
viewing and listening, it may infringe the copyright protected
by the copyright laws.
• In the PC input mode (- page 20), this function is not
available.
Adjusting the picture position
Adjustment to the position of the picture may be made to suit
your viewing preferences.
1 Press M, then press Y or y to display the SET UP menu.
2 Press < or > to select Picture position.
Language
Auto tuning
Manual tuning
AV connection
Picture position
MENU
Back Watch TV
SET UP
EXIT
English
OK
OK
OK
OK
3 Press Q, then press < or > to select an item you want
to adjust.
Horizontal position
Vertical position
Reset
MENU
Picture position
EXIT
Back Watch TV
0
0
OK
4 Press Y or y to adjust the settings as required.
Horizontal position 0
Note:
When the picture format is in Wide or 4:3 mode, only the
Horizontal position can be adjusted.
Resetting the picture position
This function resets your picture position settings to the factory
settings.
1 From the Picture position menu, press < or > to
select Reset.
2 Press Q.
Selecting the picture mode
You can select the picture quality instantly among three preset
modes and one user-set mode.
• Press N to select the desired picture quality.
Dynamic
Mode Picture quality
q Dynamic bright and dynamic picture
q Standard standard picture
q Mild soft picture
q Memory the picture quality you set
Note:
In the PC input mode (- page 20), this mode is not available.
Adjusting the basic picture quality
1
Press M, then press Y or y to display the PICTURE
menu.
Picture settings
Color management
Base color adjustment
Active Backlight Control
Cinema mode
meta brain PRO 100
MENU
PICTURE
EXIT
Back Watch TV
OK
Off
On
On
On
2 Press < or > to select the Picture settings menu,
then press Q.
Back light
Contrast
Brightness
Color
Tint
Sharpness
MENU
Back Watch TV
Picture settings 1/ 2
EXIT
100
100
50
50
0
0
3 Press < or > to select an item you want to adjust, then
press Y or y to adjust the settings as required.
Contrast 100
Selection Y
Back light darker lighter
Contrast lower higher
Brightness darker lighter
Color paler deeper
Tint reddish greenish
Sharpness softer sharper
Notes:
• The Tint may only be adjusted on a tape which has been
recorded and played back on an NTSC VCR.
• In the PC input mode (- page 20), Color, Tint and
Sharpness modes are not available.
Pressing
y
15
Using the TV’s features
Activating the black stretch
This function increases the strength of dark areas of the picture
which improves definition.
1 Press M, then press Y or y to display the PICTURE
menu.
Picture settings
Color management
Base color adjustment
Active Backlight Control
Cinema mode
meta brain PRO 100
MENU
PICTURE
EXIT
Back Watch TV
OK
Off
On
On
On
2 Press < or > to select the Picture settings menu,
then press Q.
3 Press < or > to select Black stretch on the 2nd page.
Black stretch
MPEG NR
DNR
Color Temperature
MENU
Picture settings 2/ 2
EXIT
Back Watch TV
On
Low
Auto
Cool
4 Press Y or y to select On or Off.
Black stretch
Note:
In the PC input mode (- page 20), this mode is not available.
On
Activating the MPEG NR (Noise Reduction)
If the receiving signal of MPEG is a mosquito (grained) noise
depending on the compression and conversion, the noise may
be reduced when using this function.
2 Press Y or y to select mode you prefer.
Color Temperature
Cool: Lends a blue hue to the picture.
Normal: Neutral
Warm: Lends a red hue to the picture.
Cool
Adjusting the color management
You can adjust the picture color quality by selecting from 6
base color adjustments : Red, Green, Blue, Yellow,
Magenta or Cyan.
1 From the PICTURE menu, press < or > to select
Color management.
2 Press Y or y, then press < or > to select On.
Color management
On
3 Press Q, then press < or > to select Base color
adjustment.
4 Press Q, then press < or > to select an item you want
to adjust.
5 Press y, then press Y or y to select Hue or Saturation.
Base color adjustment
Hue
Saturation
Red
Green
Blue
Yellow
Magenta
Cyan
Reset
MENU
Back Watch TV
EXIT
0
0
0
0
0
0
0
0
0
0
0
0
OK
6 Press < or > to adjust the settings as required.
Red
Hue0Saturation
0
1 From the Picture settings menu, press < or > to
select MPEG NR on the 2nd page.
2 Press Y or y to select Off, Low, Middle or High.
MPEG NR
Note:
In the PC input mode (- page 20), this mode is not available.
High
Activating the DNR (Digital Noise
Reduction)
If the receiving signal is weak and the picture is blurry, the
picture may be improved when using this function.
1 From the Picture settings menu, press < or > to
select DNR on the 2nd page.
2 Press Y or y to select Auto, Off, Low, Middle, or High.
DNR
Auto
Selecting the color temperature
You can change the tone of the picture by selecting from three
preset color temperatures: Cool, Normal or Warm.
1 From the Picture settings menu, press < or > to
select Color Temperature on the 2nd page.
Notes:
• If you select color management Off mode, this mode is not
available.
• In the PC input mode (- page 20), this mode is not
available.
Resetting the base color adjustment
The Reset function adjusts the base color adjustment to the
factory settings.
1 From the Base color adjustment menu, press < or
> to select Reset.
2 Press Q.
Using the active backlight control
In order to improve screen visibility, the active backlight
control sets the screen brightness automatically during dark
scenes.
1 From the PICTURE menu, press < or > to select
Active Backlight Control.
2 Press Y or y to select On or Off.
16
Using the TV’s features
Using the cinema mode
A movie film’s picture runs at 24 frames a second, whereas
movie software such as DVD, etc., that you enjoy watching on
television at home runs at 30 (NTSC) or 25 (PAL) frames a
second. To convert this signal to reproduce a smooth motion
and picture quality, select the On mode.
Effective signal and setup conditions:
• When the Video input mode is selected.
• When the input signal format is 480i and 576i signals.
1 From the PICTURE menu, press < or > to select
Cinema mode.
2 Press Y or y to select On or Off.
Note:
When a DVD movie with subtitle is playing back, this mode
may not work correctly.
Using the meta brain PRO 100
This function improves the viewing quality of a motion
picture.
1 From the PICTURE menu, press < or > to select meta
brain PRO 100.
2 Press Y or y to select On or Off.
Notes:
• If on-screen noise occurs when activated, select the Off
mode.
• If double-window mode is used (- page 23), this mode is
not available.
Sound adjustment
Setting the MTS (Multi-channel TV Sound)
Auto mode
The MTS Auto mode automatically recognize stereo/bilingual
programs depending on the broadcast signal.
1 Press M, then press Y or y to display the SOUND menu.
MTS
Dual
Headphone
Headphone level
Bass
Treble
MENU
SOUND 1/ 2
EXIT
Back Watch TV
2 Press < or > to select MTS, then press Y or y to select
Auto or Mono.
Mono mode
If you experience noise or poor reception of any stereo/
bilingual program, set the MTS mode to Mono.
Noise will be reduced and reception may improve.
Note:
If you experience noise with a particular program on whose
channel reception is usually good, try setting MTS mode to
Auto, then switch g to e Mono (monaural) (- page 18).
Selecting the dual 1 or dual 2 mode
You can hear only dual 1 or dual 2 sound selected, whenever
bilingual programs are received.
Auto
Dual 1
Mode 1
0
0
1 Press M, then press Y or y to display the SOUND menu.
2 Press < or > to select Dual, then press Y or y to select
Dual 1 or Dual 2.
Notes:
• When the MTS setting is in Mono mode, the Dual menu is
not selectable.
• The Dual menu setting status remains even if the TV is
turned off.
17
Using the TV’s features
Selecting the stereo programs
1
When a stereo program is received, d Stereo appears.
2 Press g to select the stereo/monaural mode. d
Stereo and e Mono appear cyclically on the screen.
Stereo
Selecting the bilingual programs
1
When a bilingual program is received, e Dual appears.
2 Press g to select the sound to be heard. The sound
differs according to the transmission system: NICAM or
German stereo/bilingual broadcast.
Dual 1
Sound to be heard
Display
NICAM
German stereo/
bilingual broadcast
j Dual 1 Sub I sound Main sound
J Dual 2 Sub II sound Sub sound
e Mono Main sound —
Note:
These settings are not stored in the TV memory.
Adjusting the sound quality
WOW consists of three features; SRS 3D, FOCUS, and
TruBass, being turned on.
1 From the SOUND menu, press < or > to select WOW
on the 2nd page, then press Q.
Balance
WOW
Stable sound
Speaker
MENU
Back Watch TV
SOUND 2/ 2
EXIT
0
OK
Off
On
2 Press < or > to select an item you want to adjust, then
press Y or y to adjust the settings as required.
SRS 3D
FOCUS
TruBass
MENU
WOW
EXIT
Back Watch TV
SRS 3D: To turn the surround effect On or Off.
FOCUS: To turn the vocal emphasis effect On or Off.
TruBass: To select the desired bass expansion level
(Off, Low or High).
Notes:
• If the broadcast is monaural, the SRS 3D effect does not
work.
• WOW, SRS and l
Inc.
• WOW technology is incorporated under license from SRS
Labs, Inc.
• The SRS WOW effect is active only when the sound outputs
from the speaker.
®
symbol are trademarks of SRS Labs,
Off
On
High
1
Press M, then press Y or y to display the SOUND menu.
MTS
Dual
Headphone
Headphone level
Bass
Treble
MENU
Back Watch TV
SOUND 1/ 2
EXIT
Auto
Dual 1
Mode 1
0
0
2 Press < or > to select an item you want to adjust, then
press Y or y to adjust the settings as required.
Bass 0
Selection Y Pressing y
Bass weaker stronger
Treble weaker stronger
Balance decreases the right
channel
decreases the left
channel
Using the SRS WOW surround sound
SRS WOW is a special combination of SRS Labs audio
technologies that creates a thrilling surround sound experience
with deep, rich bass from stereo sound sources. Your TV’s
audio will sound fuller, richer and wider.
Using the stable sound
The Stable sound function limits the highest volume level to
prevent extreme changes in volume when the signal source
changes (for example, to prevent the sudden increase in
volume that often happens when a TV program switches to a
commercial).
1 From the SOUND menu, press < or > to select Stable
sound on the 2nd page.
2 Press Y or y to select On or Off.
Note:
The Stable sound effect is active only when the sound outputs
from the speaker.
Activating the speaker
Use this function to turn the TV speakers off when you connect
an audio system (- page 25).
1 From the SOUND menu, press < or > to select
Speaker on the 2nd page.
2 Press Y or y to select On or Off.
18
Using the TV’s features
Selecting the woofer internal/external
mode
1
Press M, then press Y or y to display the SET UP menu.
Language
Auto tuning
Manual tuning
AV connection
Picture position
MENU
Back Watch TV
SET UP
EXIT
English
OK
OK
OK
OK
2 Press < or > to select AV connection, then press Q
to display the AV connection menu.
AV connection
PC/HDMI1 audio
HDMI1 audio
Woofer
Audio output
MENU
Back Watch TV
EXIT
PC
Digital
External
Fixed
3 Press < or > to select Woofer, then press Y or y to
select Internal or External.
• Internal is to use the bass boost.
• External is to use an external woofer system.
Using the bass boost
1
Select the woofer Internal mode as shown above.
2 Press t to display Bass boost level.
Bass boost 70
3 While the Bass boost display is on the screen, press Y
or y to adjust the Bass boost level.
4 To turn off the Bass boost, press t to display Bass
boost Off.
Bass boost Off
Note:
The Bass Boost effect is active only when the sound outputs
from the speaker or an external woofer system.
Using an external woofer system
Connect an external woofer to the WOOFER output terminal
located on the rear of the TV (- page 25).
1 Select the woofer External mode from the AV
connection menu.
2 Press
t
to display External Woofer level, then press
Y or y to adjust the External Woofer level.
External Woofer 70
Selecting the audio output
With the audio output function “Variable”, you can use the
TV’s remote controller to adjust the sound volume of the
external audio system connected (- page 25).
To select the sound volume from AUDIO OUT
terminals:
1 From the AV connection menu, press < or > to select
Audio output.
2 Press Y or y to select Variable or Fixed.
Note:
Make sure the volume control of your audio amplifier is set to a
moderate listening level.
Other features settings
Selecting the timer menu
The Timer is especially useful if you want the TV to turn itself
on or off after a selected period of time.
1 Press M, then press Y or y to display the TIMER menu.
Sleep timer
On timer
On timer Position
MENU
TIMER
EXIT
Back Watch TV
2 Press < or > to select the required timer mode (Sleep
timer (Turn off the TV) or On timer).
The timer display will set by 10 minutes, up to 12 hours
and 50 minutes.
3 Press the Number buttons (0-9), Y or y to set the On or
Off delay time, e.g. on in 30 minutes and On timer
Position 3 selected.
4 Press P to exit the menu. When setting the On timer,
press < or > to select the On timer Position and enter
the program position number you want to watch. Set the
Standby mode by pressing J on the remote control or 1
on the TV.
Activation of the Timer is indicated by the green “Ontimer indicator”, on the front of the TV (- page 8).
Notes:
• The TV will automatically turn itself off after approximately 2
hours if you do not operate the TV after turned on by on timer
function.
• If you press and hold
the timer display will set by 30 minutes, up to 12 hours 30
minutes.
Y or y to set the On or Off delay time,
00:00
00:30
03
3 To turn off the External Woofer, press t to display
External Woofer Off.
External Woofer Off
19
Using the TV’s features
Using the auto format
When the TV receives a true HDMI signal picture and the auto
format is On, it will automatically be displayed in HDMI
signal format, irrespective of the TV’s previous setting.
1 Press M, then press Y or y to display the FUNCTION
menu.
Teletext
Teletext SW
Auto format
Blue Screen
Side panel
MENU
FUNCTION
EXIT
Back Watch TV
Auto
On
On
1
1
2 Press < or > to select Auto format, then press Y or y
to select On or Off.
Activating blue screen
With the blue screen function On, the screen will
automatically turn blue and the sound will be muted when no
signal is being received.
1 From the FUNCTION menu, press < or > to select
Blue screen.
2 Press Y or y to select On or Off.
Note:
In the PC input mode, double-window mode (- page 23) or
teletext mode (- page 21), this function is not available.
Adjusting the brightness of side panel
You can adjust the brightness of side panel in 14:9 or 4:3, etc.
mode.
1 From the FUNCTION menu, press < or > to select
Side panel.
2 Press Y or y to adjust the settings as required.
Side panel
1
Selecting the video input source to
view
1 Press and hold o or press Q on the remote control until
the video input mode list appears on the screen, then press
< or > to select appropriate input source (or press o on
the TV right side panel or o on the remote control
repeatedly to select required input source directly).
OK:
5
4
3
2
1
0
PC
HDMI2
HDMI1
Ex. PC VGA mode
PC VGA
2 Press Q.
o 1 (o (1), video 1 input) or o 1S (S-video input)
o 2 (o (2), video 2 input) or o 2S (S-video input)
o C1 (o (C1), COMPONENT VIDEO INPUT),
o C2 (o (C2), COMPONENT VIDEO INPUT),
HDMI1 (o HDMI 1 input),
HDMI2 (o HDMI 2 input),
PC (o RGB/PC, PC input)
Note:
When the component video input, PC input mode or HDMI
input mode is selected, the MONITOR output terminals (page 25) output audio signal only.
o:
(Press and hold)
C1
2
1
1
PC
HDMI2
HDMI1
20
Using the TV’s features
Setting the manual setting menu
1
Press M, then press Y or y to display the SET UP menu.
Language
Manual setting
AV connection
Picture position
MENU
Back Watch TV
SET UP
EXIT
English
OK
OK
OK
2 Press < or > to select Manual setting, then press Q.
3 Press Y or y to select an item, then press > or < to
select the item as shown below.
Manual setting
Color system:Auto
A
EXT1
OK
Store
MENU
Back Watch TV
A. Color System
Confirm that color system is set to “A” (Auto). If not,
select “A” with > or <.
B. Video label
The video label allows you to label each input source
for your TV.
To change or create video labels:
1) Press > or < repeatedly to select a character for
the first space, then press y.
2) Repeat step 1) to enter the rest of the characters.
If you would like a blank space in the label name,
you must choose a blank space from the list of
characters.
3) Press Q to store your settings.
EXIT
AB
*(blank space)
Teletext
This TV has a multi-page teletext memory, which takes a few
moments to load and it offers two ways of viewing Teletext
Auto and LIST which are explained below.
Setting up the teletext mode
To select teletext mode:
Select a channel position with the desired teletext service.
1 Press M, then press Y or y to display the FUNCTION
menu.
Teletext
Teletext SW
Auto format
Blue Screen
Side panel
MENU
2 Press < or > to select Teletext, then press Y or y to
select Auto or LIST mode.
Note:
When you are watching the teletext program, SET UP menu
and FUNCTION menu are not selectable.
Adjusting the teletext SW
If reception is weak, the picture may appear blurred, and text
may not appear clearly on the screen. In this case, use this
function to make text appear clearer.
1 From the FUNCTION menu, press < or > to select
Teletext SW.
2 Press Y or y to adjust 1, 2 or 3 modes.
Notes:
• This function may not be available in some cases.
• Only in the antenna input signal mode, this function is
available.
FUNCTION
EXIT
Back Watch TV
Auto
On
On
1
1
21
Using the TV’s features
Teletext general information
E button:
Pressing E once will bring up the teletext mode. Press
again to text media window mode. Press again to return to
normal TV mode. You need to return to normal viewing if you
wish to change channels.
When you first press E to access the text service, the first
page you see will be the initial page.
In Auto mode, this displays the main subjects available and
their relevant page numbers.
In LIST mode, you will see the page numbers currently stored
on the each color button.
Note:
If you press r while the text media window mode is activated,
this mode is not available on the teletext mode.
Sub-pages:
Once in this chosen page, if there are sub-pages they will
automatically load into memory without changing the one you
are reading. If there are many sub-pages, it will take a long
time for them all to load and this will depend on the speed with
which the broadcaster transmits them.
To access the sub-pages in memory, press l, then use >
and < to view them.
Using Auto mode
There are two Modes: Auto will display FASTEXT, if
available. LIST will display your four favorite pages. In either
mode, as an alternative to the colored buttons, you can access
a page by entering a 3-digit number, using the Number
buttons on the remote control, or to advance to the next page,
press >, to go back to the previous page press <.
To change between Auto and LIST, see above.
•Press E to access teletext.
Using LIST mode
1
Press E to access teletext.
100 TEXT M00 14:58:55
100 200 300 400
Red
Green
Yellow
Blue
The four choices at the bottom of the screen are now
number – 100, 200, 300 and 400, which have been
programmed into the TV’s memory.
2 To view these pages, use the colored prompt buttons.
e.g. press the Green button to view page 200.
3 If you want to change these stored pages, press the
colored button for the color you want to change.
e.g. Press the Green button and enter the 3-digit number.
100 TEXT M00 14:58:59
100 250 300 400
This number will change in the top left of the screen and
in the colored highlight.
4 Press Q to store your choice. The bars at the bottom of
the screen will flash white.
5 You may view other pages by simply entering the 3-digit
page number – but NEVER press Q or you will lose the
favorite already stored.
100 Spor t 14:57:55
SwimmingRacingBaseballFootball
Red
Green
Yellow
Blue
If FASTEXT is available, you will see 4 colored titles at the
bottom of the TV screen. To access any given subject, simply
press the relevant colored button on the remote control.
If FASTEXT is not available, you can access any page simply
by entering a 3-digit page number or pressing the
corresponding colored button.
For further information on your particular text system(s), see
the broadcast teletext index page or consult your local Toshiba
dealer.
22
Using the TV’s features
Teletext buttons on the remote control
Below is an introduction to the teletext buttons on your remote
control and their functions.
E To display a page of teletext:
Press E to display teletext mode. Press again to the text
media window mode. Press again to return to normal TV
mode.
k To display an index/initial page:
In Auto-mode
Press k to access the index page. The one displayed is
dependant on the broadcaster.
In LIST-mode
Press k to return to the 100 page or initial page.
A To reveal concealed text:
Some pages cover topics such as quizzes and jokes. To
discover the solutions, press A.
B To hold a wanted page:
This function is included as it is part of the broadcast teletext
system but you will not need it as this TV allows you to control
the display of sub-pages.
C To enlarge the teletext display size:
Press C once to enlarge the top half of the page, press again
to enlarge the bottom half of the page. Press again to revert to
the normal size.
D To select a page while viewing a normal
picture:
When in teletext mode, if a page selection is made and then
D is pressed, a normal picture will be displayed. The TV
will indicate when the page is present by displaying the title
bar of the text page at the top of the screen. Press E to
view the page.
Note:
It will not be possible to change program position while in
Teletext mode, you will have to cancel the teletext first by
pressing E to return to a normal TV picture.
To select the time display:
If you press D while watching a normal TV broadcast,
you will see a time display from the broadcaster. It will remain
on the screen for about 5 seconds.
Using the double-window
• The double-window function allows you to split the screen
into a Main and Sub window and watch two programs at the
same time. You can display the TV program or the video
input on the Main and Sub window.
• When you watch one channel simultaneously in the doublewindow mode, differences in image quality between the
Main picture and Sub-picture occurs (except for HDMI
mode).
Displaying the double-window
1
Select the TV program you want to watch.
2 Press e to display the double-window.
Stereo
Main
window
source
4 ABCD
Main Picture Sub-Picture
AB
Notes:
• When you select the TV program of the Sub-window, the
sound is monaural only.
• In the PC input mode (- page 20) or teletext mode (-
page 21), this mode is not available.
• The still mode will be cancelled if it receives a different input
signal when changing program position or video mode is
selected, etc.
3 Press F G H w or W to select a program position or
video input source, or switch and adjust speaker sound for
each window (A, B).
Press F G H w
Stereo
4
ABCD 2 EFGH
A B
• PBb, o: available for A
• Speaker sound: A
• 2 – +: available for A
• r: A
Press F G H W
Stereo
4 ABCD
2 EFGH
Sub-window
source
2 EFGH
9:56 and 25 seconds p.m.
21:56:25
A B
• PBb, o: available for B
• Speaker sound: A
• 2 – +: available for A
• r: B
(continued)
23
Using the TV’s features
Press F G H W
4 ABCD
Stereo
2 EFGH
A B
• PBb, o: available for B
• Speaker sound: B
• 2 – +: available for B
• r: B
Press F G H w
Stereo
4
ABCD 2 EFGH
A B
• PBb, o: available for A
• Speaker sound: B
• 2 – +: available for B
• r: A
Selecting the headphone mode
You can select either Mode 1 or Mode 2.
Mode 1: Linked with the selected window
Mode 2: Linked with another window
Using a headphone
Connect a headphone to the headphone jack on the right side
mode
mode
- page 8).
Headphone Speakers
No sound
– + is available.)
(2
Sound comes out
(Headphone level menu
– + is available.)
(2
is available.)
Headphone sound is the same as speaker sound.
Headphone Speakers
No sound
– + is available.)
(2
A (or B)
(Headphone level menu
– + is available.)
(2
is available.)
A: Main window B: Sub-window
of the TV (
When in a single window:
Headphone
Mode 1 Sound comes out
Mode 2 Sound comes out
When in double-window:
Headphone
Mode 1 A (or B)
Mode 2 B (or A)
1 Press M, then press Y or y to display the SOUND menu.
MTS
Dual
Headphone
Headphone level
Bass
Treble
MENU
Back Watch TV
SOUND 1/ 2
EXIT
Auto
Dual 1
Mode 1
0
0
2 Press < or > to select Headphone, then press Y or y
to select Mode 1 or Mode 2.
MTS
Dual
Headphone
Headphone level
Bass
Treble
MENU
Back Watch TV
SOUND 1/ 2
EXIT
Auto
Dual 1
Mode2
30
0
0
Adjusting the headphone volume (Mode 2)
1
From the SOUND menu, press < or > to select
Headphone.
Press Y or y to select Mode 2.
2 Press < or > to select Headphone level.
Press Y or y to adjust the Headphone volume.
Headphone level 30
24
Connecting your TV
Side connections
You can connect a wide variety of auxiliary equipment via the
terminals located on the right side of the panel o (2).
Please always refer to the owner’s manual of the equipment to
be connected for full details.
Connection example
TV right side view
Back connections
Connection example
VCR
(S-Video or Normal)
TV back view
Set Top Box
DVD video player
(with component video outputs)
Woofer system with amplifier
Audio system
DVI device
Camcorder Camcorder with
• To select the side inputs, press and hold o until the video
input mode list appears on the screen, then press < or > to
select o2 (- page 20), then press Q.
• Before connecting any external equipment, turn off all main
power switches.
• If you connect both of the S-VIDEO input terminal and
VIDEO input terminal, the S-VIDEO signal will appear on
the screen (display changes to o 2S).
• If you connect mono sound equipment to o (2), connect the
audio output of the equipment to the L/MONO jack on the
TV.
• You can enjoy Video Games with this TV. However
shooting games, where the player shoots at a target on the
TV screen with a light gun, may not work because of the
LCD Color TV properties.
Video Games
S-Video
VCR (Recording)
TV back view
• Before connecting any external equipment, turn off all main
power switches.
• The unauthorized recording of television programs, DVDs,
video tapes and other materials may infringe upon the
provisions of copyright law.
• If you connect both of the S-VIDEO input terminal and
VIDEO input terminal, the S-VIDEO signal will appear on
the screen (display changes to o 1S).
• The COMPONENT VIDEO INPUT consists of three
component video signals (Y, P
the best picture performance. These terminals can only be
used with the component video compatible equipment e.g.
DVD video player, etc.
• Additional equipment and cables shown are not supplied
with this TV.
B/CB, PR/CR) and provides
HDMI device
25
Connecting your TV
Connecting an HDMI and a DVI
device
• This TV is not intended for connection to and should not be
used with a PC.
• When turning on your electronic components, turn on the
TV first, and then the HDMI and DVI device.
• When turning off your electronic components, turn off the
HDMI and DVI device first, and then the TV.
• This TV may not be compatible with features and/or
specifications that may be added in the future.
• This TV is only operable with L-PCM on 32/44.1/48 kHz
and 16/20/24 bits. If there is no sound when using HDMI,
use the analog audio cables to connect the TV and the HDMI
device, and select Analog in HDMI audio of the AV
connection menu (- page 27).
• This TV is able to connect with HDMI devices. But it is
possible that some HDMI devices may not operate properly
with this TV.
Connecting an HDMI and a DVI device
The HDMI input on your TV receives digital audio and
uncompressed digital video from an HDMI device and
uncompressed digital video from a DVI device.
This input is designed to accept HDCP program material in
digital from EIA/CEA-861/861B compliant consumer
electronic devices (such as a set top box and DVD player with
HDMI and DVI output).
The HDMI input is designed for best performance with 1080i
(50 Hz/60 Hz) and 1080p (50 Hz/60 Hz) high-definition video
signals, but will also accept and display 480i, 480p, 576i, 576p,
720p (50 Hz/60 Hz (60Hz: except for the E-EDID)) and VGA
signals.
• HDMI: High-Definition Multimedia Interface
• DVI: Digital Video Interface
• HDCP: High-bandwidth Digital Content Protection
• EIA/CEA-861/861B compliance covers the transmission of
uncompressed digital video with high-bandwidth digital
content protection, which is being standardized for
reception of high-definition video signals. Because this is an
evolving technology, it is possible that some devices may
not operate properly with the TV.
• E-EDID: Enhanced-Extended Display Identification
• VGA: VESA 640 5 480 @ 60 Hz
• L-PCM: Linear-Pulse Code Modulation
Connecting an HDMI device
One HDMI cable (type A connector)
TV back view
HDMI device
VIDEO AUDIO
LR
IN
OUT
HDMI OUT
For proper operation, it is recommended that you use a short
HDMI cable.
HDMI cable transfers both video and audio.
Connecting a DVI device
One HDMI (type A connector)-to-DVI adapter cable and
audio cables
TV back viewTV back view
DVI device
VIDEO AUDIO
LR
IN
OUT
HDMI (type A connector)-to-DVI adapter cable
For proper operation, the length of an HDMI-to-DVI adapter
cable should not exceed 3m. The recommended length is 2m.
Standard analog audio cables
An HDMI-to-DVI adapter cable transfers only video.
Separate analog audio cables are required.
Note:
HDMI, the HDMI logo, and High-Definition Multimedia
Interface are trademarks or registered trademarks of HDMI
Licensing, LLC.
DVI
OUT
26
Connecting your TV
Selecting the PC/HDMI audio mode
You can select PC audio or HDMI audio when using this
function (- page 26).
1 Press M, then press Y or y to display the SET UP menu.
Language
Auto tuning
Manual tuning
AV connection
Picture position
MENU
SET UP
EXIT
Back Watch TV
2 Press < or > to select AV connection, then press Q
to display the AV connection menu.
AV connection
PC/HDMI1 audio
HDMI1 audio
Woofer
Audio output
MENU
EXIT
Back Watch TV
3 Press < or > to select PC/HDMI1 audio, then press Y
or y to select PC or HDMI1.
English
OK
OK
OK
OK
PC
Digital
External
Fixed
Connecting a computer
An analog RGB (15 pin) computer cable can be connected.
TV back view TV back view
Mini D-sub 15 pin
Computer
RGB PC cable
Conversion adapter
(if necessary)
Audio cable for PC-to-TV connection
Connect a PC cable from the computer to the o RGB/PC
terminal on the back of the TV.
Setting the HDMI1 audio mode
You can select sound of an HDMI or DVI device connected to
the HDMI input terminals (- page 26) from three modes:
Auto, Digital or Analog.
Note:
This function is available only when the PC/HDMI1 audio mode
is set to
1 From the AV connection menu, press < or > to select
o
2 Press Y or y to select Auto, Digital or Analog.
HDMI1.
HDMI1 audio.
PC/HDMI1 audio
HDMI1 audio
Woofer
Audio output
MENU
AV connection
EXIT
Back Watch TV
HDMI1
Auto
External
Fixed
The following signals can be displayed:
• VGA: VESA 640 5 480 @ 60/75 Hz
• SVGA: VESA 800 5 600 @ 60/75 Hz
• XGA: VESA 1024 5 768 @ 60/70/75 Hz
• W-XGA: VESA 1280 5 768 @ 60/75 Hz
• S-XGA: VESA 1280 5 1024 @ 60/75 Hz
However, these signal formats are converted to match the
number of pixels of the LCD panel.
Therefore, the TV may not display small text properly.
If you connect this unit to your PC, the compressed image is
displayed in S-XGA mode, therefore the picture quality may
deteriorate and characters may not be read.
Notes:
• Some PC models cannot be connected to this TV.
• If connecting a certain PC model that signal is particular, the
PC signal may not be detected correctly.
• There is no need to use an adapter for computers with DOS/
V compatible mini D-sub 15 pin terminal.
• A bar may appear in the upper, lower, right or left side of the
screen, or parts of the picture may be obscured depending
on some signals. This is not the malfunction.
• If the edges of the picture are stretched, readjust the picture
position adjustments in the PC Setting menu.
• Depending on the specification of the PC you are playing
the DVD-Video on, and the DVD’s title, some scenes may be
skipped, or you may not be able to pause during multi-angle
scenes.
27
Connecting your TV
Signal names for mini D-sub 15 pin connector
Pin assignment for RGB/PC terminal
5
10
15 11
1
6
Pin No. Signal name Pin No. Signal name
1R9NC
2 G 10 Ground
3B11NC
4 NC (not
12 NC
connected)
5 NC 13 H-sync
6 Ground 14 V-sync
7 Ground 15 NC
8 Ground
Using the PC setting
• In the PC input mode, you cannot select the Color, Tint,
Sharpness, Black stretch, MPEG NR and DNR in the
Picture setting menu and Cinema mode (- page 17).
• In the PC input mode, the Manual setting (- page 21) is
not displayed.
• First press and hold o until the video input mode list
appears on the screen, then press < or > and Q in order
to select the PC input mode (- page 20).
• This function may not be available for some signal or if no
signal is received.
• The optimum points of the clock phase and sampling clock
adjustments may be incomprehensible according to the
input signals.
Adjusting the clock phase of the picture
If the clock phase, which synchronize the PC signal and LCD
display, is not optimized, the picture will blur.
This function enables you to adjust clock phase and display a
clear picture.
1 From the PC Setting menu, press < or > to select
Clock phase.
2 Press Y or y to obtain a clear picture.
Clock phase 0
Adjusting the sampling clock
If the sampling clock does not match with the dot clock
frequency of the PC, blurred picture detail will occur, or screen
width will change, or drift patterns in vertical lines may be
apparent.
This function enables you to adjust it and optimize the picture.
1 From the PC Setting menu, press < or > to select
Sampling clock.
2 Press Y or y to optimize the picture.
Sampling clock 0
Resetting the PC setting
The Reset function adjusts the PC Setting to the factory
settings.
1 From the PC Setting menu, press < or > to select
Reset on the 2nd page.
Reset
PC Setting 2 /2
0
OK
Adjusting the picture size/position
1
Press M, then press Y or y to display the SET UP menu.
2 Press < or > to select PC Setting.
Language
AV connection
PC Setting
MENU
Back Watch TV
SET UP
EXIT
English
OK
OK
3 Press Q to display the PC Setting menu.
Horizontal position
Horizontal width
Vertical position
Vertical height
Clock phase
Sampling clock
MENU
PC Setting 1 /2
EXIT
Back Watch TV
0
0
0
0
0
0
4 Press < or > to select an option you want to adjust.
Press Y or y to adjust the settings as required.
Horizontal position 0
28
2 Press Q.
MENU
Back Watch TV
EXIT
Reference section
Troubleshooting
Before calling a service technician, please check the following
table for a possible cause of the symptom and some solutions.
Symptom and solution
TV will not turn on
• Make sure the power cord is plugged in, then press !
and 1.
• The remote control batteries may be dead. Replace the
batteries.
No picture, no sound
• Check the antenna connections.
No sound, picture OK
• The sound may be muted. Press Y, y or u.
• The station may have broadcast difficulties. Try another
channel.
• Check that the Speaker function in SOUND menu is
properly set.
Poor sound, picture OK
• The station may have broadcast difficulties. Try another
channel.
Poor picture, sound OK
• Check the antenna connections.
• The station may have broadcast difficulties. Try another
channel.
• Adjust the PICTURE menu.
Poor reception of broadcast channels
• Check the antenna connections.
• The station may have broadcast difficulties. Try another
channel.
• Make sure the Color system is properly set.
Teletext problems
• Check the antenna connections.
Good performance of text depends on a good strong
broadcast signal.
Some pixels of the screen do not light up
• The LCD display panel is manufactured using an
extremely high level of precision technology, however,
sometimes some pixels of the screen may be missing
picture elements or have luminous spots. This is not a sign
of a malfunction.
The brightness of the screen comes down, or flickers
of the screen are caused, or some parts of the screen
do not light up.
• When you just buy and start to use this TV, a flickering
may be caused in the screen. In this case, switch off the
TV, then switch on it again to cure the condition.
• The cold cathode fluorescent lamp used for the back light
on this TV has longevity. When the brightness of the
screen comes down, or the flickers of the screen are
caused, or some parts of the screen do not light up, it may
reach the end of its life. Contact a service technician.
The picture brightness varies when you display
switch the TV on.
• If you switch the TV on at 0°C and under, wait until the
warms up.
Multiple images
• The station may have broadcast difficulties. Try another
channel.
• Antenna reception may be poor. Use a high directional
outdoor antenna.
• Check if the direction of the antenna has changed.
Poor color or no color
• The station may have broadcast difficulties. Try another
channel.
• Adjust the Tint and/or Color in the PICTURE menu.
The remote control does not operate
• Remove all obstructions between the remote control and
the remote control sensor on the TV.
• The remote control batteries may be dead. Replace them
with new ones.
• Check that the TV/STB/DVD switch on the remote
control is properly set.
Broadcast system
Broadcast transmission systems of each
country or region
Asia M.E.
Country or region Color Sound
Bahrain, Kuwait, Israel, Oman,
Qatar, United Arab Emirates,
Yemen, etc. Indonesia, Malaysia,
Singapore, Thailand, etc.
China PAL D/K
China Hong Kong PAL I
Iraq, Islamic Republic of Iran,
Lebanon, Saudi Arabia, etc.
Russian Federation, etc. SECAM D/K
Myanmar, etc. NTSC M
Oceania
Country or region Color Sound
Australia, New Zealand, etc. PAL B/G
Africa
Country or region Color Sound
Republic of South Africa, etc. PAL I
South America
Country or region Color Sound
Argentina, Paraguay, Uruguay, etc. PAL N
Brazil PAL M
Chile, Colombia, etc. NTSC M
Note:
PAL, SECAM and NTSC 3.58 (MHz) are different color signal
broadcast transmission systems applicable to different
countries or region. NTSC 4.43 (MHz) is used in special VCRs
to playback NTSC recorded video tapes through PAL
television equipment.
PAL B/G
SECAM B/G
29
Specifications
LCD color television
Model
42WL68A, 42WL68E, 42WL68T
Power source
42WL68A: 220V-240V AC, 50 Hz
42WL68E: 220V-240V AC, 50/60 Hz
42WL68T: 110V-240V AC, 50/60 Hz
Power consumption
265W, 0.6W (standby)
Dimensions
1,042 mm (W) 762 mm (H) 352 mm (D)
Mass (Weight)
35.5
kg
Television system (Antenna input)
Channel coverage:
PAL B/G (CCIR) VHF 2 - 12
UHF 21 - 69
CATV X - Z+2, S1 - S41
PAL I (UK) VHF -
UHF 21 - 69
CATV -
PAL D/K (CHINA) VHF 1 - 12
UHF 13 - 57
CATV Z1 - Z38
SECAM B/G (CCIR) VHF 2 - 12
UHF 21 - 69
CATV X - Z+2, S1 - S41
SECAM D/K (OIRT) VHF 1 - 12
UHF 21 - 69
CATV X1 - X19
NTSC M (US) VHF 2 - 13
UHF 14 - 69
CATV A6 - A1, A - W, AA -
ZZ, AAA, BBB
NTSC M (JAPAN) VHF 1 - 12
UHF 13 - 62
CATV M1 - M10, S1 - S41
Special RF signal:
NTSC 4.43 color system 5.5/6.0/6.5 MHz sound system
PAL 60 Hz color system 5.5/6.0/6.5 MHz sound system
Reference section
Visible size (diagonal)
106.7 cm
Number of pixels
1366 (H) dots 5 768 (V) dots
Audio power
9 W + 9 W (7% THD), 10 W + 10 W (10% THD)
Speakers
Main 60 5 120 mm 4pcs.
Tweeter 33 mm (round) 2pcs.
Input/Output terminals
o (1) Input
o (2) Input
o (C1) Input
o (C2) Input
O MONITOR Output
O AUDIO OUT Output
O WOOFER Output
o RGB/PC Input
o PC/HDMI1
o HDMI1 Input (type A)
o HDMI2 Input (type A)
Headphone jack 3.5 mm (Diameter) stereo
Operating condition
Temperature 0°C - 35°C
Humidity 20% - 80% (No moisture condensation)
Supplied accessories
Owner’s manual (1), Remote control (1), Batteries (2),
Clip (1)
(AUDIO)
4 pin S-video
Phono jacks A/V
4 pin S-video
Phono jacks A/V
Component video Y, P
Phono jacks Audio L/Mono + R
Component video Y, P
Phono jacks Audio L/Mono + R
Phono jacks A/V
Audio L + R (Fixed/Variable)
Phono jacks Bass Line out
Mini D-sub 15 pin Analog RGB
Input
Phono jacks Audio L+R
19 pin A/V Digital
19 pin A/V Digital
B/CB, PR/CR
B/CB, PR/CR
(Variable)
COMPONENT VIDEO INPUT terminals (the signal
format)
480i, 480p, 576i, 576p, 720p (50/60 Hz), 1080i (50/60 Hz)
(These signal formats are converted to match the number of
pixels of the LCD panel.)
Color system
PAL, SECAM, NTSC 3.58/4.43
Aspect ratio
16 : 9
30
This is used to fix the TV to a wall, pillar, etc. (- page 4).
• Design and specifications are subject to change without
notice.
• Never service or remodel the TV by yourself. It may expose
you to a fire hazard or dangerous voltages.
31
VX1A00032000
YC/J
Loading...