TOSHIBA 42RV500E, 42RV500T, 42RV500Y, 46RV500E, 46RV500T User Guide

...
OWNER'S MANUAL
LCD Color TV
42RV500E 42RV500T 42RV500Y 46RV500E 46RV500T 46RV500Y
©2009 TOSHIBA CORPORATION All Rights Reserved VX1A001099A0
Owner's Record
You will find the model number and serial number on the back of the TV. Record these numbers in the spaces provided below. Refer to them whenever you call upon your TOSHIBA dealer regarding this product.
Model number:
Contents
Introduction
Welcome to Toshiba .................................................................................................. 3
Important Safety Instructions .................................................................................... 3
Important information ................................................................................................ 7
Getting started
Connecting an antenna ............................................................................................. 8
Exploring your new TV .............................................................................................. 8
TV top, front and side panel controls ......................................................................... 9
TV back panel connections ..................................................................................... 10
Learning about the remote control .......................................................................... 11
Turning the TV on .................................................................................................... 13
Learning about the menu system ............................................................................ 13
Watching TV programs ............................................................................................ 14
Programming channels into the TV’s channel memory ........................................... 15
Using the TV’s features
Picture adjustment .................................................................................................. 17
Sound adjustment ................................................................................................... 21
Using the bass boost ............................................................................................... 22
Other features settings ............................................................................................ 22
Selecting the video input source to view ................................................................. 23
Watching PIP (Picture-in-Picture) ............................................................................ 24
Using REGZA-LINK ................................................................................................ 25
Teletext .................................................................................................................... 27
Connecting your TV
Side connections ..................................................................................................... 29
Back connections .................................................................................................... 29
Connecting an HDMI or a DVI device ...................................................................... 30
Selecting the PC/HDMI1 audio mode ..................................................................... 31
Setting the HDMI1 audio mode ............................................................................... 31
Selecting the Lip Sync ............................................................................................. 31
Connecting a computer ........................................................................................... 32
Using the PC setting ............................................................................................... 33
REGZA-LINK connection ........................................................................................ 34
Reference section
Troubleshooting ....................................................................................................... 35
Broadcast system .................................................................................................... 36
Specifi cations .......................................................................................................... 37
Introduction
Welcome to Toshiba
• Thank you for purchasing this Toshiba LCD Color Television. This manual will help you use the exciting features of your new TV.
• Instructions in this manual are based on using the remote control.
• You also can use the controls on the TV if they have the same name as those referred to on the remote control.
• Please read all safety and operating instructions in this manual carefully, and keep this manual for future reference.
Important Safety Instructions
Be sure to observe the following instructions and precautions to ensure safe use of this TV.
Installation
1) Always connect the power plug to an
appropriate electrical outlet equipped with E model: 220-240V, AC 50/60Hz, T model: 110-240V, AC 50/60Hz and Y model: 220­240V, AC 50Hz.
Never use the TV outside the specifi ed voltage range. It may cause a fi re or an electric shock.
Ex. 220-240V AC, 50/60Hz
Check!
WARNING ABOUT THREE-WIRE GROUNDING-TYPE PLUG: (Only for E models)
• This product shall be connected to a main socket outlet with a protective earthing connection.
• Never remove the earthing pin on the power plug. This system is equipped with a three pin earthing-type power plug. This plug will only fi t an earthing-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact an electrician to replace the wall outlet.
• Never defeat the purpose of the earthing plug.
About the fuse
In a three pin earthing-type, the fuse fi tted in this plug is approved by ASTA or BSI to BS1362. It should only be replaced by a correctly rated and approved type and the fuse cover must be refi tted.
2) Never insert or remove the power plug with wet hands.
This may cause an electric shock.
3) Never place the TV in an unstabilized location such as on a shaky table, incline or location subject to vibration.
The TV may drop or fall off which may cause an injury or damage.
4) Never block or cover the slots and openings in the cabinet.
• Never place the TV so that it is facing
upward or on its side.
• Never place the TV in a closet, bookcase or
other similar area where the ventilation is poor.
• Never drape a newspaper, tablecloth or
curtain on the TV.
• When installing the TV against a wall,
always keep the TV at least 10 cm away from the wall.
• Never place the TV on a soft unstable
surface, such as a carpet, or a cushion. The inside of this TV will overheat if the ventilation holes are covered, blocked or sealed, which may result in a fi re.
3
Introduction
5) Never place the TV near a heater or in direct sunlight.
The surface of the cabinet or power cord may melt and result in a fi re or an electric shock.
6) Never place the TV in an area exposed to high humidity levels, such as in a bathroom or close to a humidifi er.
This may cause a fi re or an electric shock.
7) Never place the TV next to a stove where it will be exposed to oil, smoke, or steam, or in a location where there is a large quantity of dust.
This may cause a fi re or an electric shock.
8) Install the TV in a horizontal, stable location. Connect between two clips on the back of the TV and a wall, pillar, etc., with a sturdy tie and clip of supplied accessories (- page 38).
• Use as short a tie as possible to ensure the
TV is stable.
• If the TV is not installed securely, it may lean
or fall over and cause an injury.
• To prevent injury, use the exclusive optional
stand or wall-hanging bracket to install this TV on the fl oor or wall securely in accordance with a qualifi ed technician.
Sturdy tie (as short as possible)
Clip
Side view
Clip
Top view
9) Precautions for moving the TV
• When moving the TV, be sure to remove the
plug from the wall outlet and disconnect the antenna cable and audio/video cables, any steady ties. A fi re or an electric shock may result if the power cord is damaged.
• When carrying the TV, at least two people
are needed. Be sure to carry it upright.
• Never carry the TV with the screen facing up
or down.
Clip
4
10)
Precautions for installing on outdoor
antenna
An outside antenna system should not be located in the vicinity of overhead power lines, or other electric light or power circuits. If the antenna falls down or drops, it may cause an injury or an electric shock.
Introduction
3) Never insert objects (metal or paper) or pour water inside the TV through ventilation holes and other openings.
These items may cause a fi re or an electric shock. If these objects are inserted inside the TV, turn off the TV and remove the power plug from the outlet immediately and contact a service technician. Be especially careful that children do not insert objects in the TV.
Clip
Use
1) Never place hot objects or open fl ame sources, such as lighted candles or nightlights, on or close to the TV.
High temperatures can melt plastic and lead to fi res.
2) The apparatus shall not be exposed to dripping or splashing and that no objects fi lled with liquids, such as vases, shall be placed on the apparatus.
When liquids are spilled or small items are dropped inside the TV, this may cause a fi re or an electric shock. If small objects drop inside the TV, turn off the TV and remove the power plug from the outlet immediately and contact a service technician.
4) Never stand or climb on the TV.
Be especially careful in households with children to prevent them through climbing on top of the TV. It may move, fall over, break, become damaged or cause an injury.
5) When the TV will not be used for a long period of time, such as during vacation or travel, remove the power plug from the wall outlet for safety.
• The TV is not completely disconnected from
the power supply line, as minute current is consumed even when the ! Power switch is turned off.
• The Mains plug or an appliance coupler is
used as the disconnect device, therefore the disconnect device shall remain readily operable.
5
Introduction
6) Never pull on the power cord when removing the plug from the wall outlet.
Always hold the plug fi rmly when removing it. If the power cord is yanked, the cord may become damaged and a fi re or an electric shock may occur.
7) Never cut, break, modify, twist, bunch up or bent the cord or apply excessive force or tension to it.
Never place heavy objects on the cord or allow it to overheat as this may cause damage, a fi re or an electric shock. Contact a service technician if the power cord is damaged.
8) If there is thunder or lightning, never touch the antenna cable or other connected cables.
You may suffer an electric shock.
Service
1) Never repair, modify or disassemble the TV by yourself.
It may cause a fi re or an electric shock. Consult a service technician for inspection and repairs.
2) When a malfunction occurs, or if smoke or an unusual odor comes from the TV, turn off the TV and remove the power plug from the outlet immediately.
Make sure that the smoke or smell has stopped, then contact a service technician. If the TV is still used in this condition, it may cause a fi re or an electric shock.
3) If the TV is dropped or the cabinet is broken, turn off the TV and remove the power plug from the outlet immediately.
If the TV is still power used in this condition, it may cause a fi re or an electric shock. If the cabinet is broken, be careful when handling the TV to prevent an injury. Contact a service technician for inspection and repair.
4) When the TV reaches the end of its useful life, ask a qualifi ed service technician to properly dispose of the TV.
Note: The lamp unit contains a small amount of mercury. Disposal of mercury may be regulated due to environmental considerations. Dispose of the used lamp unit by the approved method for your area. For disposal or recycling information, please contact your local authorities.
6
Introduction
Cleaning
1) Remove the power plug before cleaning.
Never use solvents such as benzine or thinner to clean the TV.
• These solvents may distort the cabinet or damage its fi nish.
• If rubber or vinyl products remain in contact with the TV for a long time, a stain may result.
If the cabinet becomes dirty, clean it with a soft, dry cloth. When cleaning the surface of the LCD display, wipe the panel surface gently with a soft, dry cloth.
2) Periodically disconnect the power plug from the outlet and check it. If dust has collected on the power plug connectors, clean off the dust with a dry cloth.
This dust may cause a fi re due to reduced insulation on the plug.
Clean here
Important information
1) About LCD screen
• If you have the LCD screen facing to the
sun, the LCD screen will be damaged. Be aware of locating the TV in the place such as window side or outside of the room.
• Never press the LCD screen strongly or
scratch it, and never put anything on it. These actions will damage the LCD screen.
3) Some pixels of the screen do not light up
The LCD display panel is manufactured using an extremely high level of precision technology, however sometimes some pixels of the screen may be missing picture elements or have luminous spots. This is not a sign of a malfunction.
4) About Interference
The LCD display may cause interference in image, sound, etc. of other electronic equipment that receives electromagnetic waves (e.g. AM radios and video equipment).
5) About using under the low temperature places
If you use the TV in the room of 0°C or less, the picture brightness may vary until the LCD monitor warms up. This is not a sign of a malfunction.
6) About afterimage
If a still picture is displayed, an afterimage may remain on the screen, however it will disappear. This is not a sign of malfunction.
Exemptions
• Toshiba is not liable for any damage caused
by fi res, natural disaster (such as thunder, earthquake, etc.), acts by third parties, accidents, owner’s misuse, or uses in other improper conditions.
• Toshiba is not liable for incidental damages
(such as profi t loss or interruption in business, modifi cation or erasure of record data, etc.) caused by use or inability to use of product.
• Toshiba is not liable for any damage caused
by neglect of the instructions described in the owner’s manual.
• Toshiba is not liable for any damage caused by
misuse or malfunction through simultaneous use of this product and the connected equipment.
2) About cabinet and LCD screen
Never spray volatile compounds such as insecticide on the cabinet and LCD screen. This may cause a discoloration or damage the cabinet and LCD screen.
7
Getting started
Connecting an antenna
Optimum reception of color requires a good signal and will generally mean that an outdoor antenna must be used. The exact type and positioning of the antenna will depend upon your particular area. Your Toshiba dealer or service personnel can best advise you on which antenna to use in your area. Before connecting the antenna cable, turn off all main power switches.
VHF and/or UHF antenna
Media Recorder
IN
OUT
Antenna cable (75 7 coaxial) (not supplied)
300 7 twin-lead feeder
Antenna adaptor (not supplied)
75 7 coaxial cable
Plug (not supplied)
75 7 antenna terminal
75 7 antenna terminal
TV back view
Exploring your new TV
Installing the remote control batteries
Remove the battery cover. Insert two R03 (AAA) batteries matching the –/+ polarities of the battery to the –/+ marks inside the battery compartment.
Cautions:
Dispose of batteries in a designated disposal
area. Batteries must not be exposed to excessive heat such as sunshine, fi re or the like.
• Attention should be drawn to the environmental
aspects of battery disposal.
• Never mix battery types or combine used
batteries with new ones.
Notes:
If the remote control does not operate correctly,
or if the operating range becomes reduced, replace both batteries with new ones.
If the batteries are dead or if you will not use
the remote control for a long time, remove the batteries to prevent battery acid from leaking into the battery compartment.
Effective range
within 5 m
8
Getting started
TV top, front and side panel controls
• You can operate your TV using the buttons on the side panel or the remote control. The back and side of the panel provide the terminal connections to connect other equipment to your TV (- “Connecting your TV” pages 29 – 34).
• For the use of each control, see the pages in brackets.
You can swivel the TV screen. Swivel angle: 15 degrees to left and right.
8
1 o (Input source selection) — When no
menu is on screen, this button selects the input source (- page 23). OK — When a menu is on-screen, this button functions as the next menu navigation button (- pages 13, 24).
2 MENU — Press to access the menu system
(- page 13).
3 2 – + (Volume) — When no menu is on-
screen, these buttons adjust the volume level. I i (MENU left/right) — When a menu is on-screen, these buttons function as left/right menu navigation buttons or adjust settings (- page 13).
4 pBb (Program position) — When no
menu is on screen, these buttons select the program position. (- page 14). U u (MENU up/down) — When a menu is on-screen, these buttons function as up/down menu navigation buttons (except for the input source selection) (- page 13).
TV front viewTV top view
Headphones
(Not supplied)
76
Right side view
5
4
3
2
1
9
10
11
5 ! (Power on/Standby) — Press to turn the
TV on/ standby (- page 13).
6 ! (Power LED) — Power indicator
(- page 13).
7 4 (Green LED) — Timer indicator (- page
23).
8 (Remote sensor) — Point the remote control
toward this remote sensor (- page 8).
9 o HDMI3 (input terminal) — High-
Defi nition Multimedia Interface input receives digital audio and uncompressed digital video from an HDMI device (- page 30).
10 o (2) (Video 2 input terminals) — Optional
S-video or standard video and standard audio inputs (- page 29).
11
D (Headphone jack) — For use with
headphones.
Note:
When the Headphone jack is being used, the sound from all speakers will be muted.
9
TV back panel connections
12
13
14
15 19
16
Getting started
17
18
20
TV back view
Power cord
Cable holder*
You can use the cable holder
*
to hold antenna cable, video and audio cables etc.
When moving the TV, never hold this holder.
12 o HDMI1 (input terminal) — High-
Defi nition Multimedia Interface input receives digital audio and uncompressed digital video from an HDMI device or uncompressed digital video from a DVI device (- pages 30,
31).
13 o HDMI2 (input terminal) — High-
Defi nition Multimedia Interface input receives digital audio and uncompressed digital video from an HDMI device (- page 30).
14 o (4) (Video 4 input terminals) — High-
defi nition component video and standard (analog) stereo audio inputs (- page 29).
15 o (3) (Video 3 input terminals) — High-
defi nition component video and standard (analog) stereo audio inputs (- page 29).
10
16 o (1) (Video 1 input terminals)
Standard (composite) video and standard (analog) stereo audio inputs (- page 29).
17 o PC/HDMI1 (AUDIO) (input terminal)
— PC audio input terminal is shared with HDMI1 analog audio input terminal, and their use can be confi gured in the SET UP menu (- pages 30, 31).
18 o RGB/PC (input terminal) — For use
when connecting a personal computer (PC) (- page 32).
19 O MONITOR (output terminals)
Standard video and standard audio outputs (- page 29).
20 A (Antenna input terminal) — Analog
antenna signal input (- page 8).
Learning about the remote control
Location of controls
Getting started
To select accordingly TV, REGZA-LINK or DVD mode
Number buttons (0-9) (- pages 14, 23, 27)
To return to the previous program (- page 14)
Volume – +
(These buttons adjust
the volume level.)
• PIP on/off (Picture in Picture) (- page 24)
• Active for Toshiba ancillary device.
UVYZ (- page 13)
• Menu
OK (- pages 13, 24)
MENU (- page 13)
Teletext control buttons (Four colored buttons : Red, Green, Yellow, Blue) (- pages 27, 28)
Picture mode selection (-page 19)
Picture size selection (- page 17)
Bass boost on/off (- page 22)
When using Toshiba DVD, set the remote control to DVD mode.Then,
press to EJECT press to STOP press to PLAY press to PAUSE/STEP press to SKIP REWIND press to REWIND press to FAST FORWARD press to SKIP FORWARD
Press DVD MENU to display the menu of DVD dis c.
Press RETURN to return to the previous menu accessed.
Press TOP MENU to display the title menu on DVD disc.
Press SET UP to access the on-screen Setup menu for setting adjustment.
Press AUDIO to toggle between different audio mode.
Power on/Standby (- page 13)
Input source selection (TV, o1 - o4, HDMI1 - HDMI3,
(- page 23)
PC)
Active for Toshiba ancillary device.
Program position U u (- page 14)
PIP SWAP (- page 24)
• Active for Toshiba ancillary device.
Sound mute (This button turns off/on the sound.)
EXIT (- page 14)
To display on-screen
information (- pages 14, 16)
• Initial/index function for Teletext
(- page 28)
Teletext on/Superimpose Teletext/off (- page 27 )
When in TV mode:
Stereo/bilingual selection (- page 21) To access sub-pages when in teletext (- page 27) Picture still (- page 18)
Teletext function
To reveal concealed text (- page 28) To hold a wanted page (- page 28) To enlarge teletext display size (- page 28)
• To select a page while viewing
a normal picture (- page 28)
• To select the time display
(- page 28)
* For REGZA-LINK remote control functions, please refer to “Location of controls for REGZA-LINK mode” (- page 12).
11
Getting started
Location of controls for REGZA-LINK mode.
Set to REGZA-LINK
Number buttons for device
To display contents menu
To change volume of the AV amplifier
To display top menu
To operate menu
To display DVD menu
To work interactive service control on device
Picture mode selection
Picture size selection
To turn the device On/Off
To select input from external source, connected to the device
To change the channel
To display set up menu
To Mute AV amplifier
To exit menu or return to previous menu accessed
To display information
To select audio mode
press to EJECT press to STOP press to PLAY press to PAUSE press to SKIP REWIND press to REWIND press to FAST FORWARD press to SKIP FORWARD
REGZA-LINK mode switch on the TV remote control allows the control of connected REGZA-LINK device being watched. (- pages 25, 26)
Note:
These functions are dependent on the connected device. Not all the remote control buttons may be available. Please refer to the owner’s manual for all the connected devices.
12
Getting started
Turning the TV on
Switching on the TV
Connect the power cord to a wall outlet, the ! power indicator lights in red (standby mode).
1 Press
TV right side panel, the ! power indicator
on the remote control or ! on the
lights in green.
Note:
If you watch black and white programs when the color system mode is set to Auto, color noise may appear on the screen. In this case select the appropriate Color system (For the system of each country or region, refer to pages 15 and
36).
Switching off the TV
1 Press
TV right side panel to switch to the standby mode.
Notes:
• When the TV will not be used for a long period of time, such as during vacation or travel, remove the power plug from the wall outlet.
• The TV will automatically turn itself off after approximately 15 minutes if it is tuned to a vacant channel or a station that completes its broadcast for the day. This function does not work in external input or Blue screen Off mode. The TV will automatically turn itself off after approximately 2 hours if you do not operate the TV after turned on by on timer function.
• If power is cut off while you are viewing the TV, the Last Mode Memory function turns on the TV automatically when power is applied again. If power is going to be off for a long time and you are going to be away from your TV, unplug the power cord to prevent the TV from turning on in your absence.
on the remote control or ! on the
Learning about the menu system
We suggest you familiarize yourself with the display charts before using the menu system:
• Press M to display menu, then press Y or Z to select main menu headings.
• Press V or U to select an item.
• Press Y or Z to select or adjust setting.
• Press Q to display the next menu.
Displaying the menu chart
PICTURE menu
PICTURE
Picture settings 3D Color management
Base color adjustment
Active Backlight Control Auto Contrast MPEG NR
MENU
EXIT
Back Watch TV
SOUND menu
SOUND
MTS Dual Bass Tre bl e Balance WOW
MENU
EXIT
Back Watch TV
SET UP menu
SET UP
Language Auto tuning Manual tuning AV connection Picture position
MENU
EXIT
Back Watch TV
REGZA-LINK menu
REGZA-LINK
Enable REGZA-LINK TV Auto Input Switch TV Auto Power Auto Standby Speaker Preference
MENU
EXIT
Back Watch TV
TIMER menu
TIMER
Sleep timer On timer On timer Position
MENU
EXIT
Back Watch TV
FUNCTION menu
FUNCTION
Teletext Teletext language Auto form at 4:3 stretch Blue screen Side panel
MENU
EXIT
Back Watch TV
OK
Off
On Off Low
Auto
Dual 1
0 0 0
OK
English
OK OK OK OK
On On On On
TV Speakers
00:00 00:00
01
Auto
1 On Off On
1
DNR
1/2 1/2
Picture settings
3D Color management
MENU
Base color adjustment
Active Backlight Control Auto Contrast MPEG NR
MENU
Stable sound
Bass boost Bass boost level
1/2
MTS
MENU
Dual Bass Tre bl e Balance WOW
MENU
Language
Auto tuning Manual tuning AV connection Picture position
MENU
Enable REGZA-LINK
TV Auto Input Switch TV Auto Power Auto Standby Speaker Preference
MENU
Sleep timer
On timer On timer Position
MENU
Teletext
Teletext language Auto form at 4:3 stretch Blue screen Side panel
MENU
PICTURE
PICTURE
EXIT
Back Watch TV
EXIT
Back Watch TV
SOUND
SOUND
EXIT
Back Watch TV
EXIT
Back Watch TV
SET UP
EXIT
Back Watch TV
REGZA-LINK
EXIT
Back Watch TV
TIMER
EXIT
Back Watch TV
FUNCTION
EXIT
Back Watch TV
Auto
OK
Off
On Off
Low
Off
Off 70
Auto
Dual 1
0 0 0
OK
English
OK OK OK OK
On
On On On
TV Speakers
00:00
00:00
01
Auto
1 On Off On
1
2/2
2/2
1/2
13
Getting started
Notes:
• In the video input mode (o1 - o4), Auto
tuning and Manual tuning are not available. Instead, Manual setting appears in the SET UP menu (- page 24).
• If you connect external equipment via component video source to external input, Color system selection in the Manual setting menu is not available.
• If you do not make a selection for a while, the menu display disappears automatically.
• If you want to close the menu display instantly, press P.
• To return to the previous menu, press M.
• In the PC input mode, PC Setting appears in the SET UP menu (- page 33).
• In the 480i, 576i or 1080i input signals mode, you can select the Cinema mode in the Picture settings menu (- page 19).
• When you use the color management function (- page 20), you can select the Base color adjustment in the PICTURE menu.
Watching TV programs
Selecting the menu language
Choose from 9 different languages (English, Chinese (CS), Malay, Thai, Vietnamese, Russian, Arabic, Persian or French) for the on-screen display.
1 Press M, then press Y or Z to display SET
UP menu.
SET UP
Language Auto tuning Manual tuning AV connection Picture position
MENU
Back Watch TV
EXIT
English
OK OK OK OK
2 Press V or U to select Language. 3 Press Y or Z to select the desired language.
Changing the program position
1 Enter the desired program position number
using the Number buttons on the remote control. For program positions below 10, use 0 and the required number e.g., for program position 1.
2 You can also change the program position by
using PU or Pu. The program position will be displayed on the screen with the Mono/Stereo/Dual audio status.
Note:
The program position selection change between different format channels takes several seconds.
Switching between two program positions
You can switch two program positions without entering actual position number each time.
1 Select the fi rst program position you want to
view.
2 Select the second program position with the
Number buttons (0-9).
3 Press :. The previous channel will be
displayed.
Each time you press :, the TV will switch back and forth between the two program positions.
Displaying the on-screen information
1 Press to display the following on-screen
information.
ABCD4
Stereo
The information will disappear in 6 seconds.
• Program position or external input mode selected
• Program skip on/off information
• Label (if set)
• Mono/Stereo/Dual audio status
2 To erase the display instantly, press
again.
14
Getting started
Programming channels into the TV’s channel memory
• First, use the Auto tuning function to preset all the active channels in your area automatically. Then, arrange the preset channels with the Manual tuning function so that you can tune into only desired channels.
• Use the Manual tuning operation if desired channels cannot be preset with the Auto tuning or if you would like to preset channels to specifi c position numbers one by one.
Programming channels automatically
1 From the SET UP menu, press V or U to
select Auto tuning.
2 Press Q to display the Auto tuning menu.
Auto tuning
Press OK key to start.
!
EXIT for no change.
MENU
EXIT
Back Watch TV
3 Press Q to start the automatic search.
The search will begin for all available stations.
Searching Pos :2
EXIT
The slide bar will move along the line as the search progresses. If you make a mistake, simply repeat steps 1-3 to start again from the beginning.
Auto tuning
Stop
4 When the automatic search is completed,
the TV will automatically return to the fi rst program position.
5 Press PU or Pu to view the programmed
position.
Note:
When you preset the program channel which sound of broadcast transmission system adopts “M” system, the sound system may not be tuned correctly if the radio waves transmit badly. At that time, preset the channel by Manual tuning. The countries such as Myanmar, Brazil, Chile, Colombia apply to this case. See page 36 for more details.
Manually setting channels in the channel memory
1 From the SET UP menu, press V or U to
select Manual tuning.
2 Press Q to display the Manual tuning menu.
Press V or U to select the program position you want to arrange.
Manual tuning
Prog. Label
1
2 3 4 5 6
OK
Select
MENU
Back Watch TV
EXIT
Sort
3 Press Q to display the breakdown menu.
Press Y or Z to select an item, then press V or U to select the item as shown below.
Manual tuning
Program
A
1
B/G
OK
Store
MENU
ACE
A. Program position selection B. Sound system (- page 36) C. Color system (- page 36)
A : Automatic (factory set), P : PAL,
S : SECAM, N4 : NTSC 4.43 (MHz), N3 : NTSC 3.58 (MHz)
If the color of a certain channel is
abnormal, the automatic color system selection (A) may have malfunctioned, or sound system selection is wrong. In such a case, select another color and/or sound system (- page 36).
D. Program position skip selection
Press V or U to turn the program position
skip option on “8” or off “(”.
The program position will then be skipped
when you select channels with PU or Pu.
The “8” mark will appear beside a
program position number when you use the Number button on the remote control.
EXIT
Back Watch TV
BDF
G
15
Getting started
E. Channel search operation
Press U to search up the band or V to
search down the band.
Press V or U repeatedly until your desired
channel is displayed.
When a station/satellite is found, it will be
displayed.
NEVER PRESS ANY OTHER BUTTONS
WHILE THE SET IS TUNING.
F. Auto Fine Tuning
Press V or U to turn the Auto Fine Tuning
option on “9” or off “0”.
The Auto Fine Tuning function
automatically corrects slight fl uctuations when receiving signals.
Manual Fine Tuning While the Auto Fine Tuning turn off “0”,
press V or U so that the better picture and sound are obtained.
G. Label
Station labels appear under the program
position display each time you turn on the TV, select a channel, or press
To change or create station labels:
1) Press V or U repeatedly to select a
character for the fi rst space, then press Y or Z.
2) Repeat step 1) to enter the rest of the
characters. If you would like a blank space in the label name, you must choose a blank space from the list of characters.
Press Q to store your settings.
.
*(blank space)
Sorting program position
• The TV is capable of receiving a number of different channels depending upon where you live.
• Sorting program position is an easy way of storing each channel on the program position of your choice.
Ex.: To swap channel ABCD (Prog.1) for channel MNOP (Prog.4):
1 From the SET UP menu, press V or U to
select Manual tuning menu, then press Q.
2 Press V or U to select the channel ABCD,
then press Z.
Manual tuning
Prog. Label
1 2 3 4 5 6
OK
Select
MENU
Back Watch TV
EXIT
ABCD
EFGH IJKL MNOP
Sort
3 Press V to select the new position “4”, then
press Y.
Manual tuning
Prog.
1 2 3 4 5 6
Store
MENU
Back Watch TV
EXIT
Label EFGH IJKL MNOP
ABCD
4 Press U to select the channel MNOP, then
press Z.
5 Press U to select the new position “1”, then
press Y.
6 Confi rm new Manual tuning menu.
Manual tuning
Prog. Label
1 2 3 4 5 6
OK
Select Sort
MENU
Back Watch TV
EXIT
MNOP
EFGH IJKL ABCD
16
Using the TV’s features
Picture adjustment
Selecting the picture size
1 Press O until the picture size list appears
on the screen, then press V or U to select the appropriate picture size (or press O repeatedly to select required picture size directly).
Ex. HDMI 1080i input signal
Exact Scan
Native
Wide
Super Live 2 Cinema 2 4:3 Super Live 1 Cinema 1
Subtitle 14:9
2 Press Q.
Wide
Use this setting when watching a wide-screen DVD, widescreen video tape or a 16:9 broadcast (when available). Due to the range of wide­screen formats (16:9, 14:9, 20:9 etc.), you may see bars on the top and bottom of the screen.
4:3
Use this setting to view a true 4:3 broadcast.
Super Live 1
When receiving “4:3 format” signal, this setting will enlarge the image to fi t the screen by stretching the image vertically and horizontally, holding the better proportions at the center of the image.
Cinema 1
When watching “letterbox format” fi lms/video tapes, this setting will eliminate or reduce the black bars at the top and bottom of the screen by zooming in and selecting the image without distortion.
Super Live 2
When receiving “side panel format” signal, this setting will enlarge the image to fi t the screen by stretching the image vertically and horizontally, holding the better proportions at the center of the image. Also the black bars on the both sides of the screen will eliminate or reduce.
Cinema 2
When watching “all sides panel format” fi lms/ video tapes, this setting will eliminate or reduce the black bars on all the sides of the screen by zooming in and selecting the image without distortion.
Subtitle
When subtitles are included on a letterbox format broadcast, this setting will raise the picture so that the most of text is displayed.
Subtitle
14:9
Use this setting when watching a 14:9 broadcast.
Exact Scan
When receiving 1080i or 1080p signal format, this setting will display the image correctly without distortion or picture clipping.
17
Using the TV’s features
Native
Use this setting for PC connected via HDMI. When receiving video signal source via HDMI input, this setting will display the image correctly without distortion or picture clipping.
PC Normal
Use this setting for PC connected via HDMI or RGB/PC terminal when receiving PC signal format. This setting will display the image correctly without distortion or picture clipping.
PC Wide
Use this setting for PC connected via HDMI or RGB/PC terminal when receiving PC signal format. This setting will display the image without picture clipping.
Notes:
• In the antenna input signal mode, the picture size selections are Wide, Super Live 2,
Cinema 2, 4:3, Super Live 1, Cinema 1, Subtitle and 14:9.
• In the PC connected via HDMI or RGB/PC terminal (- page 32), the picture size selection is PC Wide or PC Normal only.
• Using the special functions to change the size of the displayed image (e.g. changing the height/width ratio) for the purpose of public display or commercial gain may infringe on copyright laws.
• If the aspect ratio of the selected format is different from the one of the TV transmission or video program, it can cause a difference in vision. Change to the correct aspect ratio picture size.
• When using the PC connected via HDMI or RGB/PC terminal, the moving image quality may be deteriorated.
Using the picture still
• Press r to freeze the picture. Even if an image is frozen on the TV screen, the pictures are running on the input source. Audio continues to be output as well. To return to a moving picture, press r again.
(Moving) (Still)
Notes:
• If you use this function except for the purpose of your private viewing and listening, it may infringe the copyright protected by the copyright laws.
• In the PC input mode (- page 23), this function is not available.
• On the sub-picture mode (- page 24), this function is not available.
Adjusting the picture position
Adjustment to the position of the picture may be made to suit your viewing preferences.
1 Press M, then press Y or Z to display the
SET UP menu.
SET UP
Language Auto tuning Manual tuning AV connection Picture position
MENU
Back Watch TV
EXIT
English
OK OK OK OK
2 Press V or U to select Picture position. 3 Press Q, then press V or U to select an
item you want to adjust.
Picture position
Horizontal position
Vertical position Reset
MENU
EXIT
Back Watch TV
0
0
OK
4 Press Y or Z to adjust the settings as
required.
Horizontal position 0
Notes:
• When the picture size is in Wide or 4:3 mode, only the Horizontal position can be adjusted.
18
Using the TV’s features
• When the picture size is in Native, PC Wide, PC Normal mode, none of this function will be
available.
• The picture position adjustment is not available for Exact Scan mode.
Resetting the picture position
This function resets your picture position settings to the factory settings.
1 From the Picture position menu, press V or
U to select Reset.
2 Press Q.
Activating picture preferences
The picture modes of this TV are customizable. Press q to view the different modes available. (The q button has the same function as of the Picture Mode in Picture settings menu.)
The preset modes are: Dynamic, Standard, Mild, Movie, Game and PC (PC Fine). These modes affect many functions/settings of the TV. You can customize the settings of the current picture mode as desired. For example, if you select Dynamic, you can adjust the following settings: Backlight, Contrast, Brightness,
Color, Tint, Sharpness, Black/White Level, Cinema mode, and Color Temperature. Your
new customized settings are stored as a User setting.
Notes:
Game mode is only available in external input mode (other than antenna input). When you select Game mode, a suitable widescreen format will be selected.
PC mode is only available in RGB/PC input mode or HDMI input mode.
PC Fine mode is only available in TOSHIBA’s PC (REGZA-LINK type) input and the Enable
REGZA-LINK menu On (- page 26), then Auto mode appears in the Black/White Level and Cinema mode.
1 Select Picture settings from the PICTURE
menu.
Picture settings 1/2
Picture Mode
Back light
Contrast Brightness Color Tint
MENU
Back Watch TV
EXIT
Dynamic
100
100
50 50
0
2 Use Y and Z to adjust the Backlight,
Contrast, Brightness, Color, Tint, and Sharpness.
Setting the black/white level
Black/White Level improves the defi nition of dark areas of the picture.
1 From the Picture settings menu, press V
or U to select Black/White Level on the 2nd page.
2 Press Y or Z to select High, Off, Low or
Middle.
Black/White Level
High
Using the cinema mode
A movie fi lm’s picture runs at 24 frames a second, whereas movie software such as DVD, etc., that you enjoy watching on television at home runs at 30 (NTSC) or 25 (PAL) frames a second. To convert this signal to reproduce a smooth motion and picture quality, select the On mode.
Effective signal and setup conditions:
• When the Video input mode is selected.
• When the input signal format is 480i, 576i or 1080i signals.
1 From the Picture settings menu, press V or
U to select Cinema mode on the 2nd page.
2 Press Y or Z to select On or Off.
Note:
When a DVD movie with subtitle is playing back, this mode may not work correctly.
Adjusting the color temperature
Color Temperature increases the warmth or coolness of the picture by setting the red, green or blue tint.
1 From the Picture settings menu, press V or
U to select Color Temperature on the 2nd
page, then press Q.
2 Press Y or Z to select Cool, Natural, or
Warm to suit your preference, then press M.
Color Temperature
Color Temperature
Red Level Green Level Blue Level
MENU
EXIT
Back Watch TV
Cool
0 0 0
19
Using the TV’s features
3 Press V or U to select Red Level, Green
Level or Blue Level, then press Y or Z to
adjust the setting as required.
Resetting the picture settings
This function returns the picture settings to the factory settings.
1 From the Picture settings menu, press V or
U to select Reset on the 2nd page.
2 Press Q.
Activating the MPEG NR (Noise Reduction)
If the receiving signal of MPEG is a mosquito (grained) noise depending on the compression and conversion, the noise may be reduced when using this function.
1 From the PICTURE menu, press V or U to
select MPEG NR.
2 Press Y or Z to select Off, Low, Middle or
High.
MPEG NR
Low
Note:
In the PC input mode (- page 23), this mode is not available.
Activating the DNR (Digital Noise Reduction)
If the receiving signal is weak and the picture is blurry, the picture may be improved when using this function.
1 From the PICTURE menu, press V or U to
select DNR on the 2nd page.
2 Press Y or Z to select Auto, Off, Low,
Middle or High.
DNR
Auto
Notes:
• This function is available for 480i and 576i signals.
• In the PC input mode (- page 23), this mode is not available.
Adjusting the color management
You can adjust the picture color quality by selecting from 6 base color adjustments : Red,
Green, Blue, Yellow, Magenta or Cyan.
1 From the PICTURE menu, press V or U to
select 3D Color management.
2 Press Y or Z, then press Y or Z to select
On.
3D Color management
On
3 Press Q, then press V or U to select Base
color adjustment.
4 Press Q, then press V or U to select an
item you want to adjust.
5 Press Z, then press Y or Z to select Hue,
Saturation or Brightness.
Base color adjustment
Hue
Saturat ion Brightness
0
0
0
Red
Green Blue Yel l o w Magenta Cyan
Reset
MENU
Back Watch TV
EXIT
0 0 0 0 0
0
0
0
0
0
0
0
0
0
0
OK
6 Press V or U to adjust the settings as
required.
Hue0Saturation
Red
Brightness
0
0
Notes:
• If you select color management Off mode, this mode is not available.
• In the PC input mode (- page 23), this mode is not available.
Resetting the base color adjustment
The reset function adjusts the base color adjustment to the factory settings.
1 From the Base color adjustment menu,
press V or U to select Reset.
2 Press Q.
Note:
In the PC input mode (- page 23), this mode is not available.
Using the active backlight control
In order to improve screen visibility, the active backlight control sets the screen brightness automatically during dark scenes.
1 From the PICTURE menu, press V or U to
select Active Backlight Control.
2 Press Y or Z to select On or Off.
Note:
In the PC input mode (- page 23), this mode is not available.
20
Using the TV’s features
Activating auto contrast
When auto contrast is activated it will automatically optimize the backlighting levels to suit ambient light conditions.
1 From the PICTURE menu, press V or U to
select Auto Contrast.
2 Press Y or Z to select On or Off.
Sound adjustment
Setting the MTS (Multi-channel TV Sound)
Auto mode
The MTS Auto mode automatically recognize stereo/bilingual programs depending on the broadcast signal.
1 Press M, then press Y or Z to display the
SOUND menu.
MTS Dual Bass Tre bl e Balance WOW
MENU
Back Watch TV
SOUND
EXIT
Auto
Dual 1
OK
1/2
0 0 0
2 Press V or U to select MTS, then press Y or
Z to select Auto or Mono.
Mono mode
If you experience noise or poor reception of any stereo/bilingual program, set the MTS mode to
Mono. Noise will be reduced and reception may improve.
Note:
If you experience noise with a particular program on whose channel reception is usually good, try setting MTS mode to Auto, then switch s to e Mono (monaural).
Selecting the dual 1 or dual 2 mode
You can hear only dual 1 or dual 2 sound selected, whenever bilingual programs are received.
1 Press M, then press Y or Z to display the
SOUND menu.
2 Press V or U to select Dual, then press Y or
Z to select Dual 1 or Dual 2.
Notes:
• When the MTS setting is in Mono mode, the Dual menu is not selectable.
• The Dual menu setting status remains even if the TV is turned off.
Selecting the stereo programs
1 When a stereo program is received, d
Stereo appears.
2 Press s to select the stereo/monaural
mode. d Stereo and e Mono appear cyclically on the screen.
Stereo
Selecting the bilingual programs
1 When a bilingual program is received,
j Dual appears.
2 Press s to select the sound to be
heard. The sound differs according to the transmission system: NICAM or German stereo/bilingual broadcast.
Dual 1
Sound to be heard
Display
NICAM
German stereo/
bilingual
broadcast
j Dual 1
J Dual 2
e Mono
Sub I sound
Sub II sound
Main sound
Main sound
Sub sound
Note:
These settings are not stored in the TV memory.
Adjusting the sound quality
1 From the SOUND menu, press V or U to
select an item you want to adjust.
2 Press Y or Z to adjust the settings as
required.
Bass 0
Selection
Bass weaker stronger
Treble weaker stronger
Balance decreases the
right channel
Pressing
Y
Z
decreases the left channel
21
Using the TV’s features
Using the SRS WOW® surround sound
SRS WOW® is a special combination of SRS Labs audio technologies that creates a thrilling surround sound experience with deep, rich bass from stereo sound sources. Your TV’s audio will sound fuller, richer and wider. SRS WOW
®
consists of three features; SRS 3D®, SRS FOCUS®, and SRS TruBass®, being turned on.
1 Press M, then press Y or Z to display
SOUND menu.
MTS Dual Bass Tre bl e Balance WOW
MENU
Back Watch TV
SOUND
EXIT
Auto
Dual 1
OK
1/2
0 0 0
2 Press V or U to select WOW, then press Q. 3 Press V or U to select an item you want
to adjust, then press Y or Z to adjust the settings as required.
WOW
High
Off
On
®
SRS 3D
FOCUS TruBass
MENU
EXIT
Back Watch TV
SRS 3D: To turn the surround effect On or
Off.
FOCUS: To turn the vocal emphasis effect
On or Off.
TruBass: To select the desired bass
expansion level (Off, Low or High).
Notes:
• If the broadcast is monaural, the SRS 3D effect does not work.
• WOW, SRS and l symbol are trademarks of SRS Labs, Inc.
• WOW technology is incorporated under license from SRS Labs, Inc.
• The SRS WOW® effect is active only when the sound outputs from the speaker.
Using the stable sound
The Stable sound function limits the highest volume level to prevent extreme changes in volume when the signal source changes (for example, to prevent the sudden increase in volume that often happens when a TV program switches to a commercial).
1 From the SOUND menu, press V or U to
select Stable sound on the 2nd page.
Stable sound
Bass boost
Bass boost level
MENU
Back Watch TV
SOUND
EXIT
2/2
Off
Off
2 Press Y or Z to select On or Off.
Note:
The Stable sound effect is active only when the sound outputs from the speaker.
Using the bass boost
1 Press to display Bass boost level (There
is the same Bass boost level as of the SOUND Menu.).
Bass boost 70
2 While the Bass boost display is on the
screen, press Y or Z to adjust the Bass boost level.
3 To turn off the Bass boost, press to
display Bass boost Off.
Bass boost Off
Note:
The Bass boost effect is active only when the sound outputs from the speaker.
Other features settings
Selecting the timer menu
The Timer is especially useful if you want the TV to turn itself on or off after a selected period of time.
1 Press M, then press Y or Z to display the
TIMER menu.
TIMER
Sleep timer On timer On timer Position
MENU
Back Watch TV
EXIT
00:00 00:00
01
22
Using the TV’s features
2 Press V or U to select the required timer
mode (Sleep timer (Turn off the TV) or On
timer).
3 Press the Number buttons (0-9), Y or Z to
set the On or Off delay time. The timer display will set by 10 minutes, up to 12 hours and 50 minutes.
4 When setting the On timer, press V or U to
select the On timer Position and enter the program position number you want to watch. Press P to exit the menu. Set the Standby mode by pressing on the remote control. Activation of the Timer is indicated by the green 4 “On timer indicator”, on the front of the TV (- page 9).
Notes:
• The TV will automatically turn itself off after approximately 2 hours if you do not operate the TV after turned on by on timer function.
• If you press and hold Y or Z to set the On or Off delay time, the timer display will set by 30 minutes, up to 12 hours 30 minutes.
Using the auto format
When the TV receives a true HDMI signal picture and the auto format is On, it will automatically be displayed in HDMI signal format, irrespective of the TV’s previous setting.
1 Press M, then press Y or Z to display the
FUNCTION menu.
Teletext Teletext language Auto format 4:3 stretch Blue screen Side panel
MENU
Back Watch TV
FUNCTION
EXIT
Auto
1 On Off On
1
2 Press V or U to select Auto format, then
press Y or Z to select On or Off.
Activating blue screen
With the blue screen function On, the screen will automatically turn blue and the sound will be muted when no signal is being received.
1 From the FUNCTION menu, press V or U to
select Blue screen.
2 Press Y or Z to select On or Off.
Note:
In the PC input mode, PIP mode (- page 24) or teletext mode (- page 27), this function is not available.
Activating the 4:3 stretch
When 4:3 stretch is activated, this function will switch 4:3 format programs into a full screen picture.
1 From the FUNCTION menu, press V or U to
select 4:3 stretch.
2 Press Y or Z to select On or Off.
Note:
In HDMI signal format, this function is available.
Adjusting the brightness of side panel
You can adjust the brightness of side panel in 14:9 or 4:3, etc. mode.
1 From the FUNCTION menu, press V or U to
select Side panel.
2 Press Y or Z to adjust the settings as
required.
Side panel
1
Selecting the video input source to view
1 Press o or press Q on the remote control
until the video input mode list appears on the screen, then press V, U or o to select appropriate input source (or press o on the TV right side panel to select required input source directly).
o:OK:
o4
HDMI1 HDMI2 HDMI3 PC 0 1 2 3
REGZA-LINK
TV
o1 o2 o3 o4
HDMI1 HDMI2 HDMI3 PC
Ex. PC VGA mode
PC VGA
2 Press Q.
o 1 (o (1), video 1 input), o 2 (o (2), video 2 input) or o 2S (S-video
input),
o 3 (o (3), component video input), o 4 (o (4), component video input),
HDMI1, HDMI2, HDMI3 (HDMI input), PC (o RGB/PC, PC input)
23
Using the TV’s features
Notes:
• When the component video input, PC input mode or HDMI input mode is selected, the MONITOR OUT output terminals (- page 29) output audio signal only.
• If a REGZA-LINK device is connected to an HDMI input, the REGZA-LINK icon will appear.
• When the TV is switched on, it will take a few minutes for the REGZA-LINK icon to appear in the list; when an HDMI cable is removed, it will take a few minutes for the icon to disappear.
• If the HDMI cable from connected device is changed or HDMI device setting are changed, Enable REGZA-LINK in the REGZA-LINK menu may need to be reset to On.
Setting the manual setting menu
1 Press M, then press Y or Z to display the
SET UP menu.
SET UP
Language Manual setting AV connection Picture position
MENU
Back Watch TV
EXIT
English
OK OK OK
2 Press V or U to select Manual setting, then
press Q.
3 Press Y or Z to select an item, then press V
or U to select the item as shown below.
Manual setting
Color system:Auto
A
EXT1
OK
Store
MENU
A. Color System
Confi rm that color system is set to “A” (Auto). If not, select “A” with V or U.
B. Video label
The video label allows you to label each input source for your TV.
To change or create video labels:
1) Press V or U repeatedly to select a
character for the fi rst space, then press Y or Z.
24
EXIT
Back Watch TV
AB
*(blank space)
2) Repeat step 1) to enter the rest of the characters. If you would like a blank space in the label name, you must choose a blank space from the list of characters.
3) Press Q to store your settings.
Watching PIP (Picture-in-Picture)
• This TV is capable of displaying two pictures simultaneously.
• This is called the PIP (Picture-in-Picture) function. A TV picture or a picture from external source equipment can be displayed as a sub­picture.
• When the main picture is the TV picture, the sub-picture can only be from external source equipment (via HDMI or PC signal).
• When the main picture is a picture from external source equipment, the sub-picture can only be from the TV.
Displaying a sub-picture
1 Select the TV program and HDMI or PC
signal you want to watch.
2 Press the button. A sub-picture will
appear on the screen.
Main picture source Sub-picture source
(Main picture)
(Sub- picture)
Note:
The sub-picture has no sound.
Changing the position of the sub-picture
1 Press V, U, Y or Z repeatedly. The display
position of the sub-picture will change in order 1 to 4.
Changing the position of the sub-picture
1 Press the button. The main and sub-
picture are switched.
2 Press the button again to switch again.
Using the TV’s features
Using REGZA-LINK
This feature uses CEC (Consumer Electronics Controls) technology and allows the control of Toshiba REGZA-LINK compatible devices from the TV remote control via HDMI connection (- page 34).
Note:
Not all Toshiba products currently support REGZA-LINK.
REGZA-LINK one touch play
When connected device is turn on REGZA-LINK will automatically detect the TV through the input selection. If the TV is in standby it will be turn on automatically. This feature is selected in the REGZA-LINK setup menu.
Notes:
• When using this mode, the PIP function (-
page 24) is canceled.
• Even if the device is showing a menu the TV may automatically show the video input source on-screen display.
REGZA-LINK system standby
This feature automatically turns the connected device into standby when the TV goes into standby and conversely for the TV to switch into standby when connected device goes into standby.
REGZA-LINK system audio control
Using the Speaker Preference feature allows the TV remote control to adjust the volume or mute the sound of the speakers connected to the TV via an AV amplifi er.
Ensure that the connected AV amplifi er and REGZA-LINK device are selected in the input source selection and that the Speaker
Preference is set to Amplifi er in the REGZA- LINK setup menu.
Notes:
• When you turn on the AV amplifi er, change its input source, or adjust the sound volume, the sound will be output from the AV amplifi er’s speakers even if the TV Speakers has been selected. Turn the TV to standby and on again to output the sound from the TV’s speaker.
• The proper function may not work by operating AV Amplifi er.
• In this mode, the PIP function (- page 24) is
not available.
Note:
The above functions are dependent on the connected device and TV setting.
REGZA-LINK functions
When the Enable REGZA-LINK is set to On, it allows the following functions to be enabled by setting them to On.
TV Auto Input Switch If a connected HDMI device displays an OSD
menu or starts playing video or audio, the TV will automatically switch to the appropriate HDMI input.
TV Auto Power If a REGZA-LINK device is turned on or off, the
TV turns on or standby automatically.
Auto Standby If the TV is set to standby, the TV will send a
message to turn off the selected REGZA-LINK device connected to the TV.
Speaker Preference From this item, you can set your audio output
preference to the TV speakers or the AV amplifi er speakers. When this item is set to Amplifi er, the TV remote control can be used to adjust or mute the volume of the audio. This item will be grayed out unless a REGZA-LINK compatible AV amplifi er is connected.
Notes:
• When you turn on the AV amplifi er, change its input source, or adjust the sound volume, the sound will be output from the AV amplifi er’s speakers even if TV Speakers has been selected. Turn the TV to standby and on again to output the sound from the TV’s speakers.
• The above functions are dependent on the connected device and TV setting.
25
Using the TV’s features
To set the REGZA-LINK set up
1 Press M and Y or Z to select the REGZA-
LINK menu.
MENU
Back Watch TV
REGZA-LINK
EXIT
Enable REGZA-LINK
TV Auto Input Switch TV Auto Power Auto Standby Speaker Preference
On
On On On
TV Speakers
2 Press V or U to select Enable REGZA-
LINK, then press Y or Z to select On.
Note:
If you set Enable REGZA-LINK to Off, the all other items will be grayed out.
3 Press V or U to select the REGZA-LINK set
up item you want to use, and press Y or Z to select On/Off or the desired speakers mode.
• TV Auto Input Switch: On/Off
• TV Auto Power: On/Off
• Auto Standby: On/Off
• Speaker Preference: TV Speakers/Amplifi er/ Off (See details on the previous page.)
REGZA-LINK input source selection
When any devices using CEC technology has connected, REGZA-LINK icon shows on the input source list.
o:
TV
o1 o2 o3 o4
HDMI1 HDMI2
REGZA-LINK
HDMI3 PC
To select the REGZA-LINK input source, refer to “Selecting the video input source to view” on page 23.
Notes:
• This function depend on the devices connected.
• When the TV is switched on, it will take a few minutes for the REGZA-LINK icon to appear in the list; when an HDMI cable is removed, it will take a few minutes for the icon to disappear.
• If the HDMI cable from connected device is changed or HDMI cable from connected device setting are changed, Enable REGZA-LINK in the REGZA-LINK menu may need to be reset On.
To control the REGZA-LINK device
First select the HDMI input source with the desired REGZA-LINK device connected, then switch the mode on the remote control to REGZA-LINK and press the available button on the remote control (- page 12). On the sub-picture mode (- page 24), this function is not available.
The TV features that can be controlled by the connected device remote control are:
Power standby, Volume, Program channel, Sound mute, Input selection, Number buttons, Previous program channel.
Notes:
• These functions are dependent on the connected device. Not all the remote control buttons may be available. Please refer to the owner’s manual for all the connected devices.
• In this mode, the sub-picture (- page 24) is not available.
REGZA-LINK PC link
This feature automatically adjusts the suitable widescreen formats and picture preferences, when connected to a REGZA-LINK PC.
Notes:
• This feature depends on the connected equipment state.
• In this mode, the sub-picture (- page 24) is not available.
26
Using the TV’s features
Teletext
This TV has a multi-page teletext memory, which takes a few moments to load and it offers two ways of viewing Teletext Auto and List which are explained below.
Setting up the teletext mode
To select a language for teletext:
The language 1-4 option enables the display of different language when using Teletext.
1 Press M, then press Y or Z to display the
FUNCTION menu.
Teletext Teletext language Auto format 4:3 stretch Blue screen Side panel
MENU
Back Watch TV
FUNCTION
EXIT
Auto
1 On Off On
1
2 Press V or U to select Teletext language,
then press Y or Z to select the required language.
Language 1: English, German, Dutch, Flemish, Russian, Byelorussian, Bulgarian, Ukranian, Lettish, Lithuanian, Czech, Slovak, Estonian
Language 2: Polish, German, Dutch, Flemish, Estonian, Lettish, Lithuanian, French, Serbian, Croatian, Slovenian, Czech, Slovak, Rumanian
Language 3: English, French, Hebrew, Turkish, Arabic
Language 4: English, French, Hebrew, Turkish, Farsi (Iranian/Persian)
To select teletext mode:
Select a channel position with the desired teletext service.
1 From FUNCTION menu, press V or U to
select Teletext.
2 Press Y or Z to select Auto or List mode.
Teletext general information
button:
Pressing once will bring up the teletext screen. Press again to superimpose the teletext over a normal broadcast picture. Press again to return to normal TV mode. You need to return to normal viewing if you wish to change channels.
When you fi rst press
to access the text service, the fi rst page you see will be the initial page. In Auto mode, this displays the main subjects available and their relevant page numbers. In List mode, you will see the page numbers currently stored on the each color button.
Note:
If you press r while the picture mode is activated, this mode will be cancelled.
Sub-pages:
Once in this chosen page, if there are sub-pages they will automatically load into memory without changing the one you are reading. If there are many sub-pages, it will take a long time for them all to load and this will depend on the speed with which the broadcaster transmits them.
To access the sub-pages in memory, press l, then use Pu and PU to view them.
Using Auto mode
There are two Modes: Auto will display FASTEXT, if available. List will display your four favorite pages. In either mode, as an alternative to the colored buttons, you can access a page by entering a 3-digit number, using the Number buttons on the remote control, or to advance to the next page, press PU, to go back to the previous page press Pu. To change between Auto and List, see above.
• Press to access teletext.
100 Sport 14:57:55
Teletext
Teletext language Auto format 4:3 stretch Blue screen Side panel
MENU
Back Watch TV
FUNCTION
EXIT
List
1 On Off On
1
Note:
When you are watching the teletext program, SET UP menu and FUNCTION menu are not selectable.
SwimmingRacingBaseballFootball
Red
Green
Yell ow
Blue
If FASTEXT is available, you will see 4 colored titles at the base of the TV screen. To access any given subject, simply press the relevant colored button on the remote control.
27
Using the TV’s features
If FASTEXT is not available, you can access any page simply by entering a 3-digit page number or pressing the corresponding colored button. For further information on your particular text system(s), see the broadcast teletext index page or consult your local Toshiba dealer.
Using LIST mode
1 Press to access teletext.
100 TEXT M00 14:58:55
100 200 300 400
Green
Red
The four choices at the bottom of the screen are now number – 100, 200, 300 and 400, which have been programmed into the TV’s memory.
Yell ow
Blue
2 To view these pages, use the colored prompt
buttons. e.g. press the Green button to view page 200.
3 If you want to change these stored pages,
press the colored button for the color you want to change. e.g. Press the Green button and enter the 3-digit number.
100 TEXT M00 14:58:59
100 250 300 400
This number will change in the top left of the screen and in the colored highlight.
4 Press Q to store your choice. The bars at the
bottom of the screen will fl ash white.
5 You may view other pages by simply entering
the 3-digit page number – but NEVER press Q or you will lose the favorite already stored.
Teletext buttons on the remote control
Below is an introduction to the teletext buttons on your remote control and their functions.
To display a page of teletext:
Press to display teletext. Press again to superimpose the teletext over a normal broadcast picture. Press again to return to normal TV mode.
k To display an index/initial page:
In Auto-mode
Press k to access the index page. The one displayed is dependant on the broadcaster.
In LIST-mode
Press k to return to the 100 page or initial page.
A To reveal concealed text:
Some pages cover topics such as quizzes and jokes. To discover the solutions, press A.
B To hold a wanted page:
This function is included as it is part of the broadcast teletext system but you will not need it as this TV allows you to control the display of sub-pages.
C To enlarge the teletext display size:
Press C once to enlarge the top half of the page, press again to enlarge the bottom half of the page. Press again to revert to the normal size.
D To select a page while viewing a normal picture:
When in teletext mode, if a page selection is made and then D is pressed, a normal picture will be displayed. The TV will indicate when the page is present by displaying the title bar of the text page at the top of the screen.
Press to view the page.
Note:
It will not be possible to change program position while in Teletext mode, you will have to cancel
the teletext fi rst by pressing normal TV picture.
to return to a
To select the time display:
If you press D while watching a normal TV broadcast, you will see a time display from the broadcaster. It will remain on the screen for about 5 seconds.
9:56 and 25 seconds p.m.
21:56:25
28
Note:
If you press r while this mode is activated, this mode will be cancelled.
Connecting your TV
Side connections
You can connect a wide variety of auxiliary equipment via the terminals located on the right side of the panel o (2). Please always refer to the owner’s manual of the equipment to be connected for full details.
Connection example
TV right side view
Camcorder
• To select the side inputs, press o until the
video input mode list appears on the screen, then press PU or Pu to select o2 (- page
23), then press Q.
• Before connecting any external equipment, turn off all main power switches.
• If you connect both of the S-VIDEO input terminal and VIDEO input terminal, the S-VIDEO signal will appear on the screen (display changes to o 2S).
• If you connect mono sound equipment to o (2), connect the audio output of the equipment to the L/MONO jack on the TV.
• You can enjoy Video Games with this TV. However shooting games, where the player shoots at a target on the TV screen with a light gun, may not work because of the LCD Color TV properties.
Video Games
Camcorder with S-Video
Back connections
Connection example
DVD video player
(with component
video outputs)
TV back view
• Before connecting any external equipment, turn off all main power switches.
• The unauthorized recording of television programs, DVDs, video tapes and other materials may infringe upon the provisions of copyright law.
• The COMPONENT VIDEO INPUT consists of three component video signals (Y, P CR) and provides the best picture performance. These terminals can only be used with the component video compatible equipment e.g. DVD video player, etc.
• Additional equipment and cables shown are not supplied with this TV.
Set Top Box
VCR (Normal)
VCR
(Recording)
B/CB, PR/
29
Connecting your TV
Connecting an HDMI or a DVI device
• When turning on your electronic components, turn on the TV fi rst, and then the HDMI and DVI device.
• When turning off your electronic components, turn off the HDMI and DVI device fi rst, and then the TV.
• This TV may not be compatible with features and/or specifi cations that may be added in the future.
• This TV is only operable with L-PCM on 32/44.1/48 kHz and 16/20/24 bits. If there is no sound when using HDMI, use the analog audio cables to connect the TV and the HDMI device, and select Analog in HDMI1 audio of the AV connection menu.
• This TV is able to connect with HDMI devices. But it is possible that some HDMI devices may not operate properly with this TV.
Connecting an HDMI or a DVI device
The HDMI input on your TV receives digital audio and uncompressed digital video from an HDMI device and uncompressed digital video from a DVI device. This input is designed to accept HDCP program material in digital from CEA-861-D compliant consumer electronic devices (such as a set top box and DVD player with HDMI and DVI output). The HDMI input is designed for best performance with 1080i (50 Hz/60 Hz) and 1080p (24/50/60 Hz) high-defi nition video signals, but will also accept and display 480i, 480p, 576i, 576p, and 720p (50Hz/60 Hz (60 Hz: except for E-EDID)).
• HDMI: High-Defi nition Multimedia Interface
• DVI: Digital Video Interface
• HDCP: High-bandwidth Digital Content Protection
• CEA-861-D compliance covers the transmission of uncompressed digital video with high-bandwidth digital content protection, which is being standardized for reception of high-defi nition video signals. Because this is an evolving technology, it is possible that some devices may not operate properly with the TV.
• E-EDID: Enhanced-Extended Display Identifi cation
• Acceptable PC signal format:
VGA: VESA 640 5 480 @ 60/72/75 Hz S-VGA: VESA 800 5 600 @ 60/72/75 Hz XGA: VESA 1024 5 768 @ 60/70/75 Hz W-XGA: 1280 5 768 @ 60/75 Hz W-XGA: 1360 5 768 @ 60 Hz S-XGA: VESA 1280 5 1024 @ 60/75 Hz
However, these signal formats are converted to match the number of pixels of the LCD panel. Therefore, the TV may not display small text properly.
• L-PCM: Linear-Pulse Code Modulation
Note:
HDMI, the HDMI logo, and High-Defi nition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing, LLC.
Connecting an HDMI device
One HDMI cable (type A connector)
TV right side view
HDMI device
VIDEO AUDIO
LR
IN
OUT
For proper operation, it is recommended that you use a short HDMI cable. HDMI cable transfers both video and audio.
TV back view
HDMI OUT
30
Connecting your TV
Connecting a DVI device
One HDMI (type A connector)-to-DVI adapter cable and audio cables
TV back view
TV back view
VIDEO AUDIO
LR
IN
OUT
DVI
OUT
HDMI (type A connector)-to-DVI adapter cable
For proper operation, the length of an HDMI-to­DVI adapter cable should not exceed 3m. The recommended length is 2m.
Standard analog audio cables
An HDMI-to-DVI adapter cable transfers only video. Separate analog audio cables are required.
Selecting the PC/HDMI1 audio mode
You can select PC audio or HDMI audio when using this function.
1 Press M, then press Y or Z to display the
SET UP menu.
SET UP
Language Auto tuning Manual tuning AV connection Picture position
MENU
Back Watch TV
EXIT
English
OK OK OK OK
2 Press V or U to select AV connection, then
press Q to display the AV connection menu.
AV connection
PC/HDMI1 audio
HDMI1 audio Lip Sync
PC
Digital
3 Press V or U to select PC/HDMI1 audio,
then press Y or Z to select PC or HDMI1.
Setting the HDMI1 audio mode
You can select sound of an HDMI or DVI device connected to the HDMI input terminals from three modes: Auto, Digital or Analog.
Note:
This function is available only when the PC/HDMI1 audio mode is set to HDMI1.
1 From the AV connection menu, press V or
U to select HDMI1 audio.
PC/HDMI1 audio
HDMI1 audio
Lip Sync
MENU
Back Watch TV
AV connection
EXIT
HDMI1
Auto
On
2 Press Y or Z to select Auto, Digital or
Analog.
Selecting the Lip Sync
Lip Sync can synchronize the sound and picture. This function is only available when Lip Sync equipment is connected via HDMI.
1 From the AV connection menu, press V or
U to select Lip Sync.
2 Press Y or Z to select On or Off.
Note:
Disconnect the HDMI cable before changing the Lip Sync setting. If the HDMI cable is connected, a message will appear.
MENU
Back Watch TV
EXIT
31
Connecting your TV
Connecting a computer
To connect a PC to the RGB/PC terminal on the TV:
An analog RGB (15 pin) computer cable can be connected.
Mini D-sub 15 pin
Computer
Audio cable for PC-to-TV connection
Connect a PC cable from the computer to the o RGB/PC terminal on the back of the TV.
The following signals can be displayed:
For acceptable PC signal format, see page 30.
Notes:
• Some PC models cannot be connected to this TV.
• If connecting a certain PC model that signal is particular, the PC signal may not be detected correctly.
• There is no need to use an adapter for computers with DOS/V compatible mini D-sub 15 pin terminal.
• A bar may appear in the upper, lower, right or left side of the screen, or parts of the picture may be obscured depending on some signals. This is not the malfunction.
• If the edges of the picture are stretched, readjust the picture position adjustments in the PC Setting menu.
• Depending on the specifi cation of the PC you are playing the DVD-Video on, and the DVD’s title, some scenes may be skipped, or you may not be able to pause during multi-angle scenes.
TV back view
RGB PC cable
Conversion adapter (if
necessary)
To connect a PC to the HDMI terminal on the TV:
When connecting a PC to the HDMI terminal on the TV, use an HDMI-to DVI adapter cable and analog audio cables. If connecting a PC with an HDMI terminal, use an HDMI cable (type A connector). Separate analog audio cables are not necessary.
TV back view
TV back view
Computer
Audio cable for PC-to-TV connection
For acceptable PC signal format, see page 30.
Notes:
• The edges of the images may be hidden.
• If connecting a certain PC model that signal is particular, the PC signal may not be detected correctly.
Signal names for mini D-sub 15 pin connector
Pin assignment for RGB/PC terminal
Pin No. Signal name Pin No. Signal name
1R 9NC 2 G 10 Ground 3 B 11 NC 4 NC (not
connected) 5 NC 13 H-sync 6 Ground 14 V-sync 7 Ground 15 NC 8 Ground
12 NC
32
Connecting your TV
Using the PC setting
• In the PC input mode, you cannot select the
Color, Tint, Sharpness, Black/White Level, MPEG NR and DNR in the Picture settings menu, 3D Color management, Base color adjustment, Active Backlight Control and Cinema mode (- page 19).
• In the PC input mode, the Manual setting
(- page 24) is not displayed.
• First press o until the video input mode list
appears on the screen, then press V or U and Q in order to select the PC input mode (- page 23).
• This function may not be available for some signal or if no signal is received.
• The optimum points of the clock phase and sampling clock adjustments may be incomprehensible according to the input signals.
Adjusting the picture size/position
1 Press M, then press Y or Z to display the
SET UP menu.
SET UP
Language AV connection PC Setting
MENU
Back Watch TV
EXIT
English
OK OK
2 Press V or U to select PC Setting.
SET UP
Language AV connection
PC Setting
MENU
Back Watch TV
EXIT
English
OK OK
3 Press Q to display the PC Setting menu.
Horizontal position
Vertical position Clock phase Sampling clock Reset
MENU
PC Setting
EXIT
Back Watch TV
0
0 0 0
OK
Adjusting the clock phase of the picture
If the clock phase, which synchronize the PC signal and LCD display, is not optimized, the picture will blur. This function enables you to adjust clock phase and display a clear picture.
1 From the PC Setting menu, press V or U to
select Clock phase.
2 Press Y or Z to obtain a clear picture.
Clock phase 0
Adjusting the sampling clock
If the sampling clock does not match with the dot clock frequency of the PC, blurred picture detail will occur, or screen width will change, or drift patterns in vertical lines may be apparent. This function enables you to adjust it and optimize the picture.
1 From the PC Setting menu, press V or U to
select Sampling clock.
2 Press Y or Z to optimize the picture.
Sampling clock 0
Resetting the PC setting
The Reset function adjusts the PC Setting to the factory settings.
1 From the PC Setting menu, press V or U to
select Reset.
2 Press Q.
Note:
When a PC is connected using HDMI none of these function will be available.
4 Press V or U to select an option you want to
adjust. Press Y or Z to adjust the settings as required.
Horizontal position 0
33
Connecting your TV
REGZA-LINK connection
You can control the basic functions of connected audio/video devices using the TV’s remote control if you connect a REGZA-LINK compatible audio receiver or playback device. For an explanation of setup and operations, see pages 25 – 26.
TV back view
AV Amplifier Playback device
Playback device
Before controlling the device(s):
• After completing the above connections, set the REGZA-LINK Setup menu as you desire (- page 26).
• The connected devices must also be set. For details, see the owner’s manual for each device.
34
Notes:
• If several devices are connected, REGZA-Link feature may not operate properly.
• The REGZA-LINK function uses the CEC technology as regulated by the HDMI standard.
• For proper operation, it is recommended that you use HDMI cables with the HDMI Logo (
• This function is limited to models incorporating Toshiba’s REGZA-LINK. However, Toshiba is not liable for those operations. Refer to the individual owner’s manuals for compatibility information.
• This function will be able to operate one PC and one AV Amplifi er. But PC may not operate properly with the AV Amplifi er. Some PC models may not be effect properly by the TV.
).
Reference section
Troubleshooting
Before calling a service technician, please check the following table for a possible cause of the symptom and some solutions.
Symptom and solution
TV will not turn on
• Make sure the power cord is plugged in,
then press ! or 1.
• The remote control batteries may be dead. Replace the batteries.
No picture, no sound
• Check the antenna connections.
No sound, picture OK
• The sound may be muted. Press Y, Z or U.
• The station may have broadcast diffi culties. Try another channel.
Poor sound, picture OK
• The station may have broadcast diffi culties. Try another channel.
Poor picture, sound OK
• Check the antenna connections.
• The station may have broadcast diffi culties. Try another channel.
• Adjust the PICTURE menu.
Poor reception of broadcast channels
• Check the antenna connections.
• The station may have broadcast diffi culties. Try another channel.
• Make sure the Color system is properly set.
Teletext problems
• Check the antenna connections.
Good performance of text depends on a
good strong broadcast signal.
The brightness of the screen comes down, or fl ickers of the screen are caused, or some parts of the screen do not light up.
• When you just buy and start to use this TV, a fl ickering may be caused in the screen. In this case, switch off the TV, then switch on it again to cure the condition.
• The cold cathode fl uorescent lamp used for the back light on this TV has longevity. When the brightness of the screen comes down, or the fl ickers of the screen are caused, or some parts of the screen do not light up, it may reach the end of its life. Contact a service technician.
Some pixels of the screen do not light up
• The LCD display panel is manufactured using an extremely high level of precision technology, however, sometimes some pixels of the screen may be missing picture elements or have luminous spots. This is not a sign of a malfunction.
The picture brightness varies when you display switch the TV on.
• If you switch the TV on at 0°C and under, wait until the warms up.
Multiple images
• The station may have broadcast diffi culties. Try another channel.
• Antenna reception may be poor. Use a high directional outdoor antenna.
• Check if the direction of the antenna has changed.
Poor color or no color
• The station may have broadcast diffi culties. Try another channel.
• Adjust the Tint and/or Color in the
PICTURE menu.
The remote control does not operate
• Make sure the remote control is set to the correct device mode.
• Remove all obstructions between the remote control and the remote control sensor on the TV.
• The remote control batteries may be dead. Replace the batteries.
No REGZA-LINK operation
• The REGZA-LINK feature is available for Toshiba REGZA-LINK compatible devices.
• Make sure the HDMI cables with HDMI logo are used.
• When the connected REGZA-LINK device does not work correctly after you have changed setting of the device, turn off your TV and unplug the power cord, then plug and turn on again.
• If several devices are connected, REGZA­LINK feature may not operate properly.
• Read the owner’s manual furnished with the connected REGZA-LINK device.
35
Reference section
Broadcast system
Broadcast transmission systems of each country or region
Asia M.E.
Country or region Color Sound
Bahrain, Kuwait, Israel, Oman, Qatar, United Arab Emirates, Yemen, etc. Indonesia, Malaysia, Singapore, Thailand, etc.
China PAL D/K
China Hong Kong PAL I
Iraq, Islamic Republic of Iran, Lebanon, Saudi Arabia, etc. SECAM B/G
Russian Federation, etc. SECAM D/K
Myanmar, etc. NTSC M
Oceania
Country or region Color Sound
Australia, New Zealand, etc. PAL B/G
Africa
Country or region Color Sound
Republic of South Africa, etc. PAL I
PAL B/G
South America
Country or region Color Sound
Argentina, Paraguay, Uruguay, etc. PAL N
Brazil PA L M
Chile, Colombia, etc. NTSC M
Note:
PAL, SECAM and NTSC 3.58 (MHz) are different color signal broadcast transmission systems applicable to different countries or region. NTSC 4.43 (MHz) is used in special VCRs to playback NTSC recorded video tapes through PAL television equipment.
36
Reference section
Specifi cations
LCD color television
Model
42RV500E, 42RV500T, 42RV500Y, 46RV500E, 46RV500T, 46RV500Y
Power source
42/46RV500E: 220V-240V AC, 50/60Hz 42/46RV500T: 110V-240V AC, 50/60Hz 42/46RV500Y: 220V-240V AC, 50Hz
Power consumption
42RV500E/T/Y: 239 W, 0.9 W (standby) 46RV500E/T/Y: 273 W, 0.9 W (standby)
Dimensions
42RV500E/T/Y: 1,009 mm (W) 694 mm (H) 308 mm (D) 46RV500E/T/Y: 1,108 mm (W) 746 mm (H) 308 mm (D)
Mass (Weight)
42RV500E/T/Y: 25.0 kg 46RV500E/T/Y: 27.5 kg
Television system (Antenna input)
Channel coverage:
PAL B/G (CCIR) VHF 2 - 12
PAL I (UK) VHF -
PAL D/K (CHINA) VHF 1 - 12
SECAM B/G (CCIR) VHF 2 - 12
SECAM D/K (OIRT) VHF 1 - 12
NTSC M (US) VHF 2 - 13
NTSC M (JAPAN) VHF 1 - 12
Special RF signal: NTSC 4.43 color system
5.5/6.0/6.5 MHz sound system
PAL 60 Hz color system
5.5/6.0/6.5 MHz sound system
UHF 21 - 69 CATV X - Z+2, S1 - S41
UHF 21 - 69 CATV -
UHF 13 - 57 CATV Z1 - Z38
UHF 21 - 69 CATV X - Z+2, S1 - S41
UHF 21 - 69 CATV X1 - X19
UHF 14 - 69
A6 - A1, A - W, AA
CATV
- ZZ, AAA, BBB
UHF 13 - 62 CATV M1 - M10, S1 - S41
COMPONENT VIDEO INPUT terminals (the signal format)
480i, 480p, 576i, 576p, 720p (50/60 Hz), 1080i (50/60 Hz) (These signal formats are converted to match the number of pixels of the LCD panel.)
Color system
PAL, SECAM, NTSC 3.58/4.43
Aspect ratio
16 : 9
Visible size (diagonal)
42RV500E/T/Y: 106.7 cm 46RV500E/T/Y: 116.8 cm
Number of pixels
1920 (H) dots x 1080 (V) dots
Audio power
10 W + 10 W (10% THD)
Speakers
Main 35 5 160 mm 2pcs.
Input/Output terminals
o (1)
o (2)
o (3)
o (4)
O MONITOR
o
RGB/PC
o
PC/HDMI1
(AUDIO) 3.5 mm (Diameter) stereo
o
HDMI1
o
HDMI2
o
HDMI3
Headphone jack 3.5 mm (Diameter) stereo
Input Phono jacks A/V Input 4 pin S-video Phono jacks A/V Input Component video Y, P
Phono jacks Audio
Input Component video Y, PB/CB,
Phono jacks Audio
Output Phono jacks A/V Input Mini D-sub 15 pin Analog RGB Input
Input (type A) 19 pin A/V Digital Input (type A) 19 pin A/V Digital Input (type A) 19 pin A/V Digital V.1.3a with Lip Sync
B/CB,
R/CR
P
L/Mono +R
R/CR
P
L/Mono +R
37
Reference section
Operating condition
Temperature 0°C - 35°C Humidity 20% - 80% (No moisture condensation)
Supplied accessories
Owner’s manual (1), Remote control (1), Batteries (2), Clip (1), Cleaning cloth (1)
This is used to fi x the TV to a wall, pillar, etc. (- page 4).
• Design and specifi cations are subject to change without notice.
• Never service or remodel the TV by yourself. It may expose you to a fi re hazard or dangerous voltages.
38
Note
39
YC/ J
Loading...