Toshiba 42LZ196, 47LZ196 User Manual

Integrated High Definition LCD Television

HIGH-DEFINITION TELEVISION

42LZ196 47LZ196

IMPORTANT NOTE

Before connecting, operating, or adjusting this product, carefully read the Important Safety, Installation, Care, and Service information in the separate Installation Guide.

For an overview of steps for setting up your new TV, see page 7.

Note: To display a High Definition picture, the TV must be receiving a High Definition signal (such as an over-the-air High Definition TV broadcast, a High Definition digital cable program, or a High Definition digital satellite program). For details, please contact your TV antenna installer, cable provider, or satellite provider.

Owner’s Record

The model number and serial number are on the back of your TV. Record these numbers in the spaces below. Refer to these numbers whenever you communicate with your Toshiba dealer about this TV.

Model number:

Serial number:

YC/M

VX1A00019400

FCC Declaration of Conformity

Important notes about your Compliance Statement (Part 15):

The Toshiba 42LZ196 and 47LZ196 Televisions comply with Part 15 of the FCC rules.

Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The party responsible for compliance to these rules is: Toshiba America Consumer Products, L.L.C. 82 Totowa Rd. Wayne, NJ 07470. Ph: 1-800-631-3811

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by removing and applying power to the equipment, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the

receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for

help.

Caution: Changes or modifications to this equipment not expressly approved by Toshiba could void the user’s authority to operate this equipment.

LCD TV

The following symptoms are technical limitations of LCD

Display technology and are not an indication of malfunction;

therefore, Toshiba is not responsible for perceived issues

resulting from these symptoms.

1) An afterimage (ghost) may appear on the screen if a fixed, nonmoving image is displayed for a long period of time. The afterimage is not permanent and will disappear in a short period of time.

2) The LCD panel contained in this TV is manufactured using an extremely high level of precision technology; however, there may be an occasional pixel (dot of light) that does not operate properly (does not light, remains constantly lit, etc.). This is a structural property of LCD technology, is not a sign of malfunction, and is not covered under your warranty. Such pixels are not visible when the picture is viewed from a normal viewing distance.

Note: Interactive video games that involve shooting a “gun” type of joystick at an on-screen target may not work with this TV.

Your TV can be connected to the Internet to support firmware update, remote scheduling and e-mail capabilities. You should carefully review the information in this manual before connecting the TV to the Internet or using these features.

• If you use the remote scheduling capability of the TV, you will need a dedicated e-mail account for use by the TV only. Use of non-dedicated accounts (e.g. an account used to receive a personal e-mail) will result in the deletion of e-mail in those accounts–even if they are used only for “test” purposes. See page 75 for more information.

• If you set up any personal e-mail accounts on the TV, anyone with access to the TV will be able to read e-mail from those accounts unless you lock the profile for each e-mail account. See page 71 for more information.

• If you connect the TV to the Internet, anyone with access to the TV will be able to configure the TV to access e-mail accounts for which they have account access information (user name, password and server addresses). See page 71 for more information.

Trademark Information

• This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

• WOW, TruSurround, SRS and l symbol are trademarks of SRS Labs, Inc. WOW and TruSurround technologies are incorporated under license from SRS Labs, Inc.

• Manufactured under license from Dolby Laboratories. Dolby, Pro Logic, and the double-D symbol are registered trademarks of Dolby Laboratories.

• CableCARD

• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

• In the United States, TV GUIDE and other related marks are registered marks of Gemstar-TV Guide International, Inc. and/or one of its affiliates. In Canada, TV GUIDE is a registered mark of Transcontinental Inc., and is used under license by Gemstar-TV Guide International, Inc. The TV Guide On Screen system is manufactured under license from Gemstar-TV Guide International, Inc. and/or one of its affiliates. The TV Guide On Screen system is protected by one or more of the following United States patents 4,908,713; 6,498,895; 6,850,693; 6,396,546; 5,940,073; 6,239,794 to Gemstar-TV Guide International, Inc. and/or its subsidiaries.

• GEMSTAR-TV GUIDE INTERNATIONAL INC. AND/OR ITS RELATED AFFILIATES ARE NOT IN ANY WAY LIABLE FOR THE ACCURACY OR AVAILABILITY OF THE PROGRAM SCHEDULE INFORMATION OR OTHER DATA IN THE TV GUIDE ON SCREEN SYSTEM AND CANNOT GUARANTEE SERVICE AVAILABILITY IN YOUR AREA. IN NO EVENT SHALL GEMSTAR-TV GUIDE INTERNATIONAL, INC. AND/OR ITS RELATED AFFILIATES BE LIABLE FOR ANY DAMAGES IN CONNECTION WITH THE ACCURACY OR AVAILABILITY OF THE PROGRAM SCHEDULE INFORMATION OR OTHER DATA IN THE TV GUIDE ON SCREEN SYSTEM.

™

is a trademark of Cable Television Laboratories, Inc.

Contents

FCC Declaration of Conformity Compliance Statement

(Part 15): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Important notes about your

LCD TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Trademark Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Chapter 1: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Welcome to Toshiba . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Features of your new TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Overview of steps for installing, setting up, and

using your new TV. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

TV front and side panel controls and connections . . . . . . . . . 8

TV back panel connections. . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Chapter 2: Using the remote control . . . . . . . . . . . . . . . . . . .11

Installing the remote control batteries . . . . . . . . . . . . . . . . . 11

Remote control effective range. . . . . . . . . . . . . . . . . . . . . . . 11

Learning about the remote control . . . . . . . . . . . . . . . . . . . . 12

Remote Control functional key chart . . . . . . . . . . . . . . . . . . 14

Using the remote control to operate your other devices. . . . 16

Programming the remote control to operate

your other devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Device code setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Searching and sampling the code of a device (8500). . . 17

Using the volume lock feature (8000) . . . . . . . . . . . . . . 17

Operational feature reset (8900). . . . . . . . . . . . . . . . . . . 17

Multi-brand remote control device codes . . . . . . . . . . . . . . . 18

Chapter 3: Menu layout and navigation . . . . . . . . . . . . . . . . .22

Main menu layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Setup/Installation menu layout . . . . . . . . . . . . . . . . . . . . . . . 23

™

THINC

menu layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Navigating the menu system. . . . . . . . . . . . . . . . . . . . . . . . . 24

Chapter 4: Setting up your TV. . . . . . . . . . . . . . . . . . . . . . . .25

Selecting the menu language . . . . . . . . . . . . . . . . . . . . . . . . 25

Configuring the antenna input sources for the

ANT 1 and ANT 2 terminals . . . . . . . . . . . . . . . . . . . . . 25

Programming channels into the TV’s channel memory . . . . 26

Programming channels automatically . . . . . . . . . . . . . . 26

Manually adding and deleting channels in the channel

memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Setting the time and date. . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Setting the HDMI Viewing the CableCARD

™

audio mode . . . . . . . . . . . . . . . . . . . . . . 28

™

menu. . . . . . . . . . . . . . . . . . . . . 29

Viewing the digital signal meter . . . . . . . . . . . . . . . . . . . . . . 29

Viewing the system status. . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Chapter 5: Using the TV’s features . . . . . . . . . . . . . . . . . . . .31

Selecting the video input source to view . . . . . . . . . . . . . . . 31

Labeling the video input sources . . . . . . . . . . . . . . . . . . . . . 31

Tuning channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Tuning channels using the Channel Browser

™

. . . . . . . 32

Tuning to the next programmed channel . . . . . . . . . . . . 34

Tuning to a specific channel (programmed or

unprogrammed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Switching between two channels

using Channel Return . . . . . . . . . . . . . . . . . . . . . . . 35

Switching between two channels using SurfLock

Selecting the picture size . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Scrolling the TheaterWide

picture

™

. . . . 35

(TheaterWide 2 and 3 only) . . . . . . . . . . . . . . . . . . . . . . 37

Using the auto aspect ratio feature . . . . . . . . . . . . . . . . . . . . 38

Selecting the cinema mode (480i and 1080i signals) . . . . . . 38

Using the POP features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Using the POP double-window feature . . . . . . . . . . . . . 39

Selecting the POP window audio out. . . . . . . . . . . . . . . 40

Using the FREEZE feature . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Adjusting the picture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Selecting the picture mode . . . . . . . . . . . . . . . . . . . . . . . 41

Adjusting the picture quality . . . . . . . . . . . . . . . . . . . . . 41

Using the closed caption mode . . . . . . . . . . . . . . . . . . . . . . . 42

Closed Caption Advanced . . . . . . . . . . . . . . . . . . . . . . . 42

Digital closed captions . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Using the Closed Caption button on the

remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Adjusting the audio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Muting the sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Using the digital audio selector . . . . . . . . . . . . . . . . . . . 43

Selecting stereo/SAP broadcasts . . . . . . . . . . . . . . . . . . 44

Adjusting the audio quality . . . . . . . . . . . . . . . . . . . . . . 44

Using the StableSound

feature. . . . . . . . . . . . . . . . . . . 44

Turning off the built-in speakers . . . . . . . . . . . . . . . . . . 45

Selecting the optical audio output format . . . . . . . . . . . 45

Using the Dolby Digital Dynamic Range

Control feature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Using the Locks menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Entering the PIN code . . . . . . . . . . . . . . . . . . . . . . . . . . 46

If you cannot remember your PIN code. . . . . . . . . . . . . 46

Changing your PIN code . . . . . . . . . . . . . . . . . . . . . . . . 46

Blocking TV programs and movies

by rating (V-Chip) . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Downloading an additional rating system

for blocking TV programs and movies . . . . . . . . . . 47

Blocking channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Unlocking programs temporarily . . . . . . . . . . . . . . . . . . 49

Using the input lock feature. . . . . . . . . . . . . . . . . . . . . . 49

Using the GameTimer

™

. . . . . . . . . . . . . . . . . . . . . . . . . 50

Using the control panel lock feature . . . . . . . . . . . . . . . 50

Setting the sleep timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Setting the On/Off Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Using the PC settings feature . . . . . . . . . . . . . . . . . . . . . . . . 52

Setting the PC Audio mode . . . . . . . . . . . . . . . . . . . . . . . . . 52

Displaying TV status information using RECALL . . . . . . . 53

Understanding the auto power off feature . . . . . . . . . . . . . . 53

Understanding the last mode memory feature . . . . . . . . . . . 53

Chapter 6: Using the TV’s advanced features . . . . . . . . . . . . .54

Using the advanced picture settings features . . . . . . . . . . . . 54

Using dynamic contrast . . . . . . . . . . . . . . . . . . . . . . . . . 54

Using the static gamma feature . . . . . . . . . . . . . . . . . . . 54

Selecting the color temperature . . . . . . . . . . . . . . . . . . . 55

Using the Vertical Edge Enhancer feature. . . . . . . . . . . 55

Using CableClear

digital noise reduction . . . . . . . . . . 56

Using MPEG noise reduction. . . . . . . . . . . . . . . . . . . . . 56

Using the Color Management Pro feature . . . . . . . . . . . 57

Using the Game Mode feature . . . . . . . . . . . . . . . . . . . . 58

Using the advanced audio settings features . . . . . . . . . . . . . 59

Using the SRS WOW Using the virtual surround sound feature

Virtual/SRS TruSurround™) . . . . . . . . . . . 59

(Dolby

™

surround sound feature . . . . . . 59

Chapter 7: Using the THINC™ home network feature . . . . . . . .60

A. Connecting the TV to your home network . . . . . . . . . . . 60

B. Setting up the network address . . . . . . . . . . . . . . . . . . . . 61

Automatically setting up the network address . . . . . . . . 61

Manually setting up the network address. . . . . . . . . . . . 62

Resetting the network address . . . . . . . . . . . . . . . . . . . . 63

C. Setting up file sharing on your PC . . . . . . . . . . . . . . . . . . 63

Compatible operating systems . . . . . . . . . . . . . . . . . . . . 63

Setting up file sharing on a PC with Microsoft

Windows

Setting up file sharing on a PC with Microsoft

Windows

XP Service Pack 1 or Service Pack 2 . . 63

2000. . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

D. Setting up file sharing on the TV. . . . . . . . . . . . . . . . . . . 66

Using the software keyboard . . . . . . . . . . . . . . . . . . . . . 67

About the Software Upgrade feature . . . . . . . . . . . . . . . 67

E. Viewing/playing shared files on the TV. . . . . . . . . . . . . . 67

Media specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Using the Picture Viewer . . . . . . . . . . . . . . . . . . . . . . . . 68

Using the Audio Player . . . . . . . . . . . . . . . . . . . . . . . . . 70

F. Setting up the Personal E-mail feature . . . . . . . . . . . . . . . 71

Required information and services. . . . . . . . . . . . . . . . . 71

Setting up personal e-mail . . . . . . . . . . . . . . . . . . . . . . . 71

G. Using the Personal E-mail feature . . . . . . . . . . . . . . . . . . 73

Unread E-mail Notification . . . . . . . . . . . . . . . . . . . . . . 73

E-mail Inbox. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Read View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Message editing views . . . . . . . . . . . . . . . . . . . . . . . . . . 75

H. Setting up e-mail scheduling . . . . . . . . . . . . . . . . . . . . . . 75

Required information and services. . . . . . . . . . . . . . . . . 75

Setting up e-mail scheduling . . . . . . . . . . . . . . . . . . . . . 76

Description of fields in the “E-mail Scheduling Setup”

window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Description of fields in the “E-mail Account Setup”

window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

I. Using e-mail scheduling . . . . . . . . . . . . . . . . . . . . . . . . . . 79

E-mail parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Sending a request e-mail to the TV . . . . . . . . . . . . . . . . 79

Formatting a request e-mail . . . . . . . . . . . . . . . . . . . . . . 80

Sample request e-mails . . . . . . . . . . . . . . . . . . . . . . . . . 80

Receiving an e-mail from the TV. . . . . . . . . . . . . . . . . . 81

Modifying an existing recording or reminder . . . . . . . . 81

Chapter 8: Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . .82

General troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Home network troubleshooting . . . . . . . . . . . . . . . . . . . . . . 84

LED indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Chapter 9: Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Limited United States Warranty

for LCD Televisions 26” and Larger . . . . . . . . . . . . . . . 88

Limited Canada Warranty

for LCD Televisions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91

Chapter 1: Introduction

Welcome to Toshiba

Thank you for purchasing this Toshiba TV, one of the most innovative LCD TVs on the market.

This digital television is capable of receiving analog basic, digital basic, and digital premium cable television programming by direct connection to a cable system providing such programming. A security card provided by your cable operator is required to view encrypted digital programming. Certain advanced and interactive digital cable services (such as video-on-demand, a cable operator’s enhanced program guide, or data-enhanced television services) may require the use of a set-top box. For more information, call your local cable operator.

We have provided three separate Guides to facilitate the installation and operation of your TV.

Please use the Guides in the order shown below to get the most enjoyment from your new TV.

1)The Installation Guide explains how to connect your TV to your antenna and equipment.

2)The Operating Guide (this Guide) provides step-by-step instructions for using your TV’s many features.

3)The TV Guide On Screen explains how to set up and navigate the TV Guide On Screen

Note: The TV screen graphics in the Guides are for illustration purposes only and may be different from the screens displayed on your TV.

™

system in your TV.

™

Interactive Program Guide

Features of your new TV

The following are just a few of the many exciting features of your new Toshiba widescreen, integrated HD, LCD TV:

• Integrated digital tuning (8VSB ATSC and QAM)

eliminates the need for a separate digital converter set-top box (in most cases).

• TV Guide On Screen

(- TV Guide On Screen

• Digital CableCARD

Cable TV programs (- Installation Guide).

• Two HDMI

™

digital, high-definition multimedia interfaces

(- Installation Guide).

• Two sets of ColorStream

video inputs (- Installation Guide).

• SRS WOW

™

and Dolby Virtual/SRS TruSurround™

(- page 59) audio technologies.

• Digital Audio Out optical audio connection with Dolby

Digital optical output format (- page 45; also see the Installation Guide).

• CableClear

digital picture noise reduction

(- page 56).

• Double-window POP feature (- page 39).

• PC IN (Analog RGB) computer terminal (- Installation

Guide

• Ethernet (RJ-45) (THINC

to a home network to enable file sharing (JPEG, MP3), using personal e-mail, and e-mail scheduling of recordings and reminders (- Chapter 7 and Installation Guide).

• Color Management Pro allows you to adjust the TV’s

standard colors and create up to three additional custom colors. The menu for this feature has a unique “black” design to enhance contrast while you’re adjusting the color.

• The Personal E-mail feature allows you to access your

e-mail server through the TV. You can create, view, reply to, and forward personal e-mails and JPEG format picture attachments.

™

no-fee interactive program guide

™

Interactive Program Guide).

™

slot for viewing encrypted digital

HD high-resolution component

™

) port for connecting the TV

Chapter 1: Introduction

Overview of steps for installing, setting up, and using your new TV

Follow these steps to set up your TV and begin using its many exciting features.

1 Carefully read the important safety, installation, care, and

service information in the separate Installation Guide. Keep this manual for future reference.

2 Observe the following when choosing a location for the

TV:

• Read the separate Installation Guide.

• Read the separate TV Guide On Screen

Program Guide.

• Read “Important notes about your LCD TV”

(- page 2).

• Place the TV on the floor or a sturdy, level, stable

surface that can support the weight of the unit. Secure the TV to a wall, pillar, or other immovable structure as described in the Installation Guide.

• Place the TV in a location where light does not reflect

on the screen.

• Place the TV far enough from walls and other objects to

allow proper ventilation. Inadequate ventilation may cause overheating, which will damage the TV. THIS TYPE OF DAMAGE IS NOT COVERED UNDER THE TOSHIBA WARRANTY.

3 Do not plug in any power cords until AFTER you have

connected all cables and devices to your TV.

4 BEFORE connecting cables or devices to the TV, learn

the functions of the TV’s connections and controls (

- pages 8–10).

5 Connect your other electronic device(s) to the TV

(

- Installation Guide).

6 Connect the supplied G-LINK

your VCR and/or Cable box (if applicable) to the

G-LINK

On Screen only) (- Installation Guide).

™

terminal so you can use the TV Guide

™

features (applies to VCRs and cable boxes

™

/IR blaster cable from

7 Install the batteries in the remote control (- page 11). 8 See “Learning about the remote control” (- page 12) for

an overview of the buttons on the remote control.

9 Program the remote control to operate your other

device(s) (

- pages 16–21).

™

Interactive

10 AFTER connecting all cables and devices, plug in the

power cords for your TV and other devices. The red LED will blink until the TV goes into standby mode.

When the TV is in standby mode, press POWER on the TV control panel or remote control to turn on the TV. If the TV stops responding to the controls on the remote control or TV control panel and you cannot turn the TV off or on, press and hold the POWER button for 5 seconds to reset the TV.

11 See “Menu layout and navigation” for a quick overview of

the TV’s menu system (

12 See the separate TV Guide On Screen

Program Guide for details on setting up and using the

TV Guide On Screen

- page 22).

™

Interactive

™

system (if available in your area).

13 Program channels into the TV’s channel memory

(

- page 26).

14 For details on using the TV’s features, see Chapters 5

and 6.

15 For details on connecting the TV to a home network to

enable file sharing, personal e-mail, and e-mail scheduling of recordings, see Chapter 7.

16 For help, refer to the Troubleshooting Guide, Chapter 8. 17 For technical specifications and warranty information, see

Chapter 9.

18 Enjoy your new TV!

Chapter 1: Introduction

TV front and side panel controls and connections

TV front

Right side panel

1 Blue and Red LEDs

See “LED indications” on page 86 for additional information.

2 Remote sensor — Point the remote control toward this

remote sensor (- “Remote control effective range” on page 11).

3 VIDEO-2 IN — The side panel A/V connections are

referred to as “VIDEO 2” and include standard A/V inputs.

4 POWER — Press to turn the TV on and off.

If the TV stops responding to the controls on the remote control or TV control panel and you cannot turn off the TV, press and hold the POWER button on the TV control panel for 5 or more seconds to reset the TV.

5 ARROWS BbC c — When a menu is on-screen, these

buttons function as up/down/left/right menu navigation buttons.

6 *MENU (ENTER) — Press to access the menu system

(- pages 22–23). When a menu is on-screen, the MENU button on the TV’s side control panel functions as the ENTER button.

TV top

** Swivel angle

10 11

Control panel

7 EXIT — Press to instantly close an on-screen menu.

8 CHANNEL bB — When no menu is on-screen, these

buttons change the channel (programmed channels only;

- page 26). When a menu is on-screen, these buttons function as up/down menu navigation buttons.

9 VOLUME C c — When no menu is on-screen, these

buttons adjust the volume level. When a menu is on-screen, these buttons function as left/right menu navigation buttons.

10 INPUT — Repeatedly press to change the source

you are viewing (ANT 1, VIDEO 1, VIDEO 2,

ColorStream HD1, ColorStream HD2, HDMI 1,

HDMI 2, PC, ANT 2).

11 GUIDE — Press to access the TV Guide On Screen

program guide (- TV Guide On Screen

Program Guide).

™

Interactive

™

Chapter 1: Introduction

TV back panel connections

For an explanation of cable types and connections, see the Installation Guide.

Chapter 1: Introduction

TV back

78 9101112 13

Chapter 2: Using the remote control

Installing the remote control batteries

To install the remote control batteries:

1 Slide the battery cover off the back of the remote control.

2 Install two “AA” size alkaline batteries. Match the + and

– symbols on the batteries to the symbols on the battery compartment.

3 Slide the battery cover on to the remote control until the

lock snaps.

Caution: Never throw batteries into a fire.

Note:

• Be sure to use AA size alkaline batteries.

• Dispose of batteries in a designated disposal area.

• Batteries should always be disposed of with the

environment in mind. Always dispose of batteries in accordance with applicable laws and regulations.

• If the remote control does not operate correctly, or if the operating range becomes reduced, replace batteries with new ones.

• When necessary to replace batteries in the remote control, always replace both batteries with new ones. Never mix battery types or use new and used batteries in combination.

• Always remove the batteries from the remote control if they are dead or if the remote control is not to be used for an extended period of time. This will prevent battery acid from leaking into the battery compartment.

Remote control effective range

For optimum performance, aim the remote control directly at the TV remote sensor. Make sure there are no obstructions between the remote control and the TV.

Point remote control toward remote sensor on front of TV.

16.4 ft (5m)

Chapter 2: Using the remote control

Learning about the remote control

The buttons used for operating the TV only are described here. For a complete list of the remote control’s functions, see the remote control functional key chart (- pages 14–15).

For a list of the buttons that operate the TV Guide On Screen system, see the separate TV Guide On Screen

™

Interactive

Program Guide.

™

1 LIGHT illuminates the keypad for five seconds.

The MODE SELECT key that is being selected blinks three times.

2 SLEEP accesses the sleep timer (

- page 51).

3 POWER turns the TV on and off. When the TV is on, the

blue LED indicator on the TV front will be illuminated.

4 MODE SELECT sets the six remote control device

modes: TV, CABLE/SAT, DVD, VCR/PVR, AUX 1, and AUX 2. Press TV until the keypad blinks 3 times to control the TV. The selected MODE key blinks each time any key is pressed. (

- page 16).

5 Software Keyboard (0-9, –/100, INPUT) used for

entering alpha-numeric data in conjunction with the THINC features (

- page 67).

6 Channel Numbers (0–9, –/100) directly tune

channels. The = button is used to tune digital channels (

- page 34) or to edit the Favorite List (- page 32).

7 INPUT selects the video input source (

- page 31).

Note: The error message “Not Available” may appear if you press a key for a function that is not available.

8 FAV BROWSER accesses the Favorites List in the

Channel Browser

9 MENU accesses the main TV menu system (

and 23) or opens a menu in the TV Guide On Screen system (

- TV Guide On Screen

™

(- page 32).

- pages 22

™

Interactive Program

™

Guide).

10 ENTER activates highlighted items in the main menu

system and the TV Guide On Screen

11 THINC accesses the THINC menu ( 12 PAGE + / - When the TV Guide On Screen

™

system.

- page 24).

™

system is open, moves from one set of screen information to the next, when applicable. Also used for paging up and down in the personal e-mail feature.

13 TV GUIDE opens the TV Guide On Screen

(

- TV Guide On Screen

™

Interactive Program Guide).

™

system

14 3 C / # c While watching TV, these buttons open the

Channel Browser

™

and tune to the previous/next channel in the History List (- page 33). (Also see “Arrow buttons,” below.)

15 Arrow buttons (BbC c) When a menu is on-screen,

these buttons select or adjust programming menus. (Also see 3 C / # c.)

16 VOL + / - adjusts the volume level. 17 CH Bb cycles through programmed channels when no

menu is on-screen (

- page 26), and functions as page up/

down when a menu is on-screen or when the TV Guide On Screen

™

system is open (- TV Guide On Screen

™

Interactive Program Guide).

Chapter 2: Using the remote control

18 EXIT closes on-screen menus and the TV Guide

™

On Screen

system.

19 INFO provides detailed information on highlighted items

in the TV Guide On Screen

On Screen

™

Interactive Program Guide).

™

system (- TV Guide

20 MUTE reduces or turns off the sound (- page 43). 21 CH RTN returns to the last viewed channel (- page 35),

or stops the Picture Viewer slide show (- page 69). Also can be used to switch between the Song Select view and File Select view in the Audio Player (- page 70).

22 RECALL displays TV status information (- page 53). 23 SKIP Z and SKIP z jump backward and forward one

day at a time in the TV Guide On Screen (- TV Guide On Screen

™

Interactive Program Guide).

™

listings

Also can be used for jumping to the beginning and end of a line when used with the software keyboard (- page 67).

24 C.CAPTION (TV/VCR) opens the closed caption/audio

selector screen (- pages 42–43). (The audio selector is not available for analog channels.) Also can be used to select the TV mode to view one program while recording another.

25 POP opens the POP double-window (- page 39) or

locks/unlocks the TV Guide On Screen (- TV Guide On Screen

™

Interactive Program Guide).

™

video window

26 FREEZE freezes the picture. Press again to restore the

moving picture.

27 PIC SIZE cycles through the picture sizes: Natural,

TheaterWide 1/2/3, Full, 4:3 HD, and Native

(

- page 36).

28 f g h j are used with the Color Management

Pro (- page 57) and THINC features (- page 73).

Chapter 2: Using the remote control

Remote Control functional key chart

•

DVD/VCR REMOTE CONTROL KEY

Toshiba TV (TV)

CABLE

SAT (satellite)

VCR

combo

• DVD/ DVD-R

MODE SELECT

LIGHT Lights the remote control keys. SLEEP Sleep timer s TV s TV s TV s TV s TV s TV s TV POWER Power Power Power Power Power Power Power Power 1 (. , ? !) Digit 1 2 (a b c) Digit 2 3 (d e f) Digit 3 4 (g h i) Digit 4 5 (j k l) Digit 5 6 (m n o) Digit 6 7 (p q r) Digit 7 8 (t u v) Digit 8 9 (w x y z) Digit 9 0 (‘ “ ( )) Digit 0

100/–/+10

INPUT ( ) PIC SIZE MENU

FAV BROWSER/ SET UP

THINC/ TOP MENU

TV GUIDE TV Guide Guide Guide --- Guide --- --- Guide INFO Guide Info Info Info --- Display --- --- Info ENTER Enter Select Select --- Select --- --- Select

C 3 # c

EXIT/ DVD CLEAR

PAGE +/– VOL +/–

Remote control device mode selection

– (digital separator)

TV/Video

select Selects the

image shape Menu/Guide

Menu FAV

BROWSER

Digit 1 Digit 1 Digit 1 Digit 1 AV input 1 Digit 1 Digit 1 Digit 2 Digit 2 Digit 2 Digit 2 AV input 2 Digit 2 Digit 2 Digit 3 Digit 3 Digit 3 Digit 3 AV input 3 Digit 3 Digit 3 Digit 4 Digit 4 Digit 4 Digit 4 AV input 4 Digit 4 Digit 4 Digit 5 Digit 5 Digit 5 Digit 5 CD Digit 5 Digit 5 Digit 6 Digit 6 Digit 6 Digit 6 Tuner Digit 6 Digit 6 Digit 7 Digit 7 Digit 7 Digit 7 Phono Digit 7 Digit 7 Digit 8 Digit 8 Digit 8 Digit 8 Cassette Digit 8 Digit 8 Digit 9 Digit 9 Digit 9 Digit 9 Aux Digit 9 Digit 9 Digit 0 Digit 0 Digit 0 Digit 0 --- Digit 0, 10 Digit 0

---

+10, +100

+100

–/--,

–/--, +10, +100

s TV s TV s TV s TV Input s TV s TV s TV s TV s TV s TV s TV s TV s TV

Menu Menu --- Menu Menu Menu Menu

--- --- --- Setup --- --- ---

THINC s TV s TV s TV Top menu s TV s TV s TV

Menu select up

Menu select down

Cursor up Cursor up --- Cursor up --- --- Cursor up Cursor

down

Cursor down

---

Cursor down

Menu select left/right

3 Back

Cursor left/ right

---

Cursor left/ right

# Next Exit Exit Exit --- DVD clear --- --- Exit Page up/

down Volume up/

down

Page up/ down

Volume up/

down

Page up/ down

Volume up/

down

--Volume up/

down

Page up/ down

Volume up/ down

Receiver/ AMP

--- --- ---

--- ---

--- --- ---

Volume up/

down

CD (AUDIO)

Volume up/down

PVR

Cursor down

Cursor left/ right

Volume up/down

Chapter 2: Using the remote control

•

REMOTE CONTROL KEY

Toshiba TV (TV)

CABLE

SAT (satellite)

VCR

DVD/VCR

combo

• DVD/

Receiver/ AMP

CD (AUDIO)

PVR

DVD-R

CH RTN/ DVD RTN

RECALL MUTE Sound mute SLOW

SKIP z SKIP Z

REW Rewind* Rewind Rewind Rewind Rewind --- Rewind Rewind PAUSE/STEP Pause* Pause Pause Pause Pause --- Pause Pause PLAY Play* Play Play Play Play --- Play Play FF Fast FWD* Fast FWD Fast FWD Fast FWD Fast FWD --- Fast FWD Fast FWD C.CAPTION

TV/VCR DISC/AM/FM --- --- --- --- --STOP Stop* Stop Stop Stop Stop --- Stop Stop

REC

CH B b POP Split s TV s TV s TV s TV s TV s TV s TV

FREEZE Freeze s TV s TV s TV s TV s TV s TV s TV A - D A - D --- --- --- --- --- --- ---

Previous channel

On-screen display

Slow FWD* Slow REW*

DAY+

DAY–

Previous channel

--- DVD RTN --- --- ---

s TV s TV s TV s TV s TV s TV s TV Sound

mute

Sound mute

--- ---

--- --- ---

Sound

mute Slow FWD

Slow REW

Sound mute

Slow FWD Slow REW

Skip FWD Skip REW

C.Caption --- TV/SAT TV/VCR ---

REC Menu (Single click)

Channel up/ down

Record (Double click)

Channel up/ down

Record (Double click)

Channel up/ down

Record (Double click)

Channel up/down

Record (Double click)

Channel up/down

mute

--- ---

---

Sound

--- --- --AM/FM

Sound

mute

Skip FWD Skip REW

Disc SKIP Disc select

Sound

mute Slow FWD

Slow REW

---

Instant replay

Record

--- --Channel

up/down

---

(Double click)

Channel up/down

Note:

• “---” = key does not send a signal in that remote control mode.

• “s TV” = key will affect the TV, even though the remote control is in another mode.

• * Not available for your TV.

Does not send IR signal.

In Software Keyboard mode, repeatedly pressing the key toggles through all available characters for that key. See “Using the software keyboard” on page 67.

Volume will affect the TV by default. When the volume is unlocked, all the devices will have their own volume if their ID has volume data. The AUDIO modes (receiver, CD) will have their own volume if volume lock is set on TV, CABLE/SAT, VCR/PVR, or DVD mode. See “Using the volume lock feature” (- page 17).

DVD/VCR combo : TV/VCR

DVD/VCR combo : DVD/VCR

DVD/DVD-R : RECORD is only for DVD-R, no function is picked for DVD.

Chapter 2: Using the remote control

Using the remote control to operate your other devices

Your TV remote control has one dedicated TV mode and five programmable multi-brand modes: CABLE/SAT, DVD, VCR/PVR, AUX 1, and AUX 2. The default device modes and programmable device modes are listed below.

Note: The TV remote control is preprogrammed to operate most Toshiba devices. To operate a non-Toshiba device or a Toshiba device that the remote control is not preprogrammed to operate, you will need to program the remote control. See “Programming the remote control to operate your other devices” (at right).

MODE SELECT

TV Toshiba TV CABLE/SAT Toshiba DST 3100 Satellite receiver DVD Orion DVD VCR/PVR Toshiba VCR AUX 1 Yamaha Audio receiver AUX 2 Onkyo Audio receiver

MODE SELECT Device mode control after programming

TV Toshiba TV CABLE/SAT DVD VCR/PVR AUX 1 AUX 2

Note: Although your new TV’s remote control includes codes for many devices, it may not include codes for some or all of the features on certain devices you wish to control. If you are unable to program the TV’s remote control to operate your device or some of the features on that device, use the device’s original remote control (or the control buttons on the device).

Default device mode control (before programming)

Multi-brand video/audio devices

Programming the remote control to operate your other devices

Device code setup

Find the code for your device brand in the remote control device code table on pages 18–21.

If more than one code is listed, try each one separately until you find one that works.

2 Press the applicable MODE SELECT button (CABLE/

SAT, DVD, VCR/PVR, AUX 1, or AUX 2), until the

MODE SELECT button blinks 3 times.

3 While holding down E, press the Number buttons to

enter the category code (0, 1, 2, 3, 4, or 5, as described below) plus the four-digit device code for your device.

Category Category code

TVs (Toshiba) 0 Cable boxes

Satellite receivers Cable/PVR combos DBS/PVR combos (1)

DVD players 2 VCRs

PVRs DBS/PVR combos (2)

Audio Amps Audio Amps/Tuners

CD players 5

• If a valid code is entered, the MODE SELECT button

will blink twice.

• If an invalid code is entered, the MODE SELECT

button will blink one long blink.

4 Point the remote control at the device and press p to test

the code.

• If the device responds to the remote control, you have

entered the correct code.

• If the device does not respond to the remote control,

repeat steps 3 and 4 using another code.

Note: After programming the remote control, make sure all necessary keys on the TV remote control (in addition to p) operate your device. If some keys are not operational, repeat the device code setup using another code (if other codes are listed for your device). If, after trying all listed codes, the necessary keys do not operate your device, use the device’s original remote control.

Chapter 2: Using the remote control

5 To control the TV, press the TV MODE SELECT button.

Note:

• Although the TV remote control includes codes for many devices, it may not include codes for some or all of the features on certain devices you want to control. If you are unable to program the TV remote control to operate your device or some of the features on that device, use the device’s original remote control (or the control buttons on the device).

• Every time you change the batteries you will need to reprogram the remote control.

• Some newer VCRs respond to either of two codes. These VCRs have a switch labeled “VCR1/VCR2.” If your VCR has this kind of switch and does not respond to the codes for your VCR brand, set the switch to the other position (“VCR1” or “VCR2”) and reprogram the remote control.

Searching and sampling the code of a device (8500)

If you do not know the device code for a particular device, you can cycle the remote control through the available codes for that device mode and sample the functions to find the code that operates the target device. The keys available to be sampled, provided they are applicable to that mode, are p, 1, z, <, and S. Invalid keys will be ignored while in program mode.

Using the volume lock feature (8000)

By default (factory setting), the remote control’s volume keys (z Z and W) are locked to the “TV” device mode.

The remote control will operate the TV’s volume, even when “TV” is not the current device mode. (This includes all remote control device modes except AUX 1 and AUX 2).

If you unlock the remote control’s volume keys, each device mode will have its own volume (if the device ID has volume data). The remote control will operate the volume of the device associated with the current device mode. (This includes all remote control device modes.)

If you lock the remote control’s volume keys to a specific device mode, the remote control will operate the volume of the device associated with the locked mode, even when the locked mode is not the current device mode. (This includes all device modes except AUX 1 and AUX 2).

When the remote control is in AUX 1 (or AUX 2) mode, the remote control will operate the volume of the device associated with the AUX 1 (or AUX 2) mode, even when the volume is locked to another mode.

See “Using the remote control to operate your other devices” on page 16.

To lock the remote control’s volume keys to a specific mode (CABLE/SAT in this example):

To cycle through each available device code and sample its functions:

1 Press the appropriate MODE SELECT button on the

remote control.

2 While holding down E, press 8, 5, 0, 0. The remote

control will enter program mode.

3 Point the remote control at the target device and press p

(or other function buttons that are available to be sampled).

4 If the device responds to the remote control:

Press E to store the device code. The MODE SELECT button will blink two times and the remote control will exit the program mode.

If the device does not respond to the remote control:

Press B, and then press p. Repeat this step until the device responds to the remote control, and then press E.

Note: When a search cycle is completed, the MODE SELECT button will blink three times. The remote control will begin to cycle through the available codes again. If no key is pressed within 10 seconds during programming, the remote control will exit the program mode and return to the previous code.

1 Press CABLE/SAT. 2 While holding down the E button, press 8, 0, 0, 0. 3 Press z. The CABLE/SAT MODE SELECT button will

blink two times (locked). The remote control’s volume keys will now operate the

volume of the device associated with the CABLE/SAT mode, even when CABLE/SAT is not the current device mode. (for all device modes except AUX 1 and AUX 2).

To unlock the remote control’s volume keys:

1 While holding down E, press 8, 0, 0, 0. 2 Press Z. The CABLE/SAT MODE SELECT button will

blink four times (unlocked).

Operational feature reset (8900)

This feature clears all programmed remote control features not related to “Device code setup” and resets the volume lock to the “TV” device mode.

To reset the remote control:

While holding down E, press 8, 9, 0, 0. The MODE SELECT button will blink four times.

Chapter 2: Using the remote control

Multi-brand remote control device codes

TVs

Brand Code

Toshiba 1524

Cable boxes

Brand Code

ABC 0003, 0008 Americast 0899 Bell South 0899 Clearmaster 0883 ClearMax 0883 Coolmax 0883 Digeo 1187 Director 0476 GoldStar 0144 Hamlin 0009, 0273 Memorex 0000 Motorola/

General Instrument/ Jerrold 0276, 0476, 0810 Motorola 1187, 1376

General Instrument/ Jerrold 0003

Multitech 0883 Pace 0008, 0237, 1877 Panasonic 0000, 0107 Paragon 0000 Philips 0317, 1305 Pioneer 0144, 0533, 0877,

1877 Pulsar 0000 Quasar 0000 RadioShack 0883 Regal 0273, 0279 Runco 0000 Samsung 0144 Scientific Atlanta 0008, 0477, 0877,

1877 Sony 1006 Starcom 0003 Supercable 0276 Supermax 0883 Torx 0003 Toshiba 0000 Tristar 0883 V2 0883 Viewmaster 0883 Vision 0883 Vortex View 0883 Zenith 0000, 0525, 0899

Satellite receivers

Brand Code

AlphaStar 0772 Chaparral 0216 Crossdigital 1109

DirecTV 0099, 0247, 0392,

0566, 0639, 0724, 0749, 0819,

1076, 1108, 1109, 1142, 1377, 1392, 1414, 1442,

1443, 1444, 1609, 1639, 1640, 1749, 1856

Dish Network System 0775, 1005, 1170,

1505, 1775

Dishpro 0775, 1005, 1505,

1775

Echostar 0775, 1005, 1170,

1505, 1775 Expressvu 0775, 1775 GE 0392, 0566 GOI 0775, 1775 Goodmans 1246 Hisense 1535 Hitachi 0819, 1250 HTS 0775, 1775 Hughes 0749, 1442, 1749 Hughes Network

Systems 0749, 1142, 1442,

1443, 1444, 1749 iLo 1535 Janeil 0152 JVC 0775, 1170, 1775 LG 1226, 1414 Magnavox 0722, 0724 Memorex 0724 Mitsubishi 0749 Motorola/General

Instrument/Jerrold 0869 Motorola 0856 NEC 0102, 0178, 1270 Next Level 0869 Panasonic 0152, 0247, 0701 Paysat 0724 Philips 0099, 0722, 0724,

0749, 0819, 1076,

1142, 1442,

1749 Pioneer 1442 Proscan 0392, 0566 Proton 1535 RadioShack 0869 RCA 0143, 0392, 0566,

0855, 1392 Samsung 1108, 1109, 1142,

1276, 1377, 1442,

1609 Sanyo 1219 Sony 0639, 1639, 1640 Star Choice 0869 Tivo 1142, 1442, 1443,

1444 Toshiba 0082, 0749, 0790,

0819, 1285, 1286,

1287, 1289, 1749,

1857, 1858 UltimateTV 1392, 1640 Uniden 0722, 0724 US Digital 1535 USDTV 1535 Voom 0869 Zenith 1856

DVD players

Brand Code

Aiwa 0641 Akai 0695, 0770, 1089 Alco 0790 Allegro 0869 Amphion Media Works 0872 AMW 0872 Apex Digital 0672, 0717, 0755,

0794, 0796, 0797, 1004, 1020,

1056, 1061, 1100 Aspire Digital 1168, 1407 Audiovox 0790, 1041, 1072 Axion 1072 B & K 0655, 0662 Blaupunkt 0717 Blue Parade 0571 Broksonic 0695 California Audio Labs 0490 Cinea 0831 CineVision 0833, 0869, 0876 Citizen 1277 Coby 0778, 0852, 1086,

1107, 1177, 1351 Craig 0831 Curtis Mathes 1087 CyberHome 0816, 0874, 1023,

1024, 1117, 1129 Daewoo 0705, 0784, 0833,

0869, 1169, 1172,

1234, 1242 Daytek 0872 Denon 0490, 0634 Desay 1407 Disney 0675, 1270 Dual 1068, 1085 Durabrand 1127 DVD2000 0521 Emerson 0591, 0675, 0821 Enterprise 0591 Fisher 0670 Funai 0675, 1334 Gateway 1073, 1077, 1158 GE 0522, 0717, 0815 Go Video 0715, 0741, 0744,

0783, 0833, 0869,

1044, 1075,

1099, 1158, 1304,

1730 GoVision 1072 GoldStar 0741 GPX 0699, 0769 Gradiente 0490 Greenhill 0717 Grundig 0539 Harman/Kardon 0582, 0702 Hitachi 0573, 0664 Hiteker 0672 iLo 1348 Initial 0717 Integra 0571, 0627 Jaton 1078

Chapter 2: Using the remote control

JBL 0702 JSI 1423 JVC 0558, 0623, 0867,

1164 jWin 1049, 1051 Kawasaki 0790 Kenwood 0490, 0534 KLH 0717, 0790, 1020,

1149 Konka 0711 Koss 0651, 1423 Landel 0826 Lasonic 0798, 1173 Lecson 1533 Lenoxx 1127 LG 0591, 0741, 0801,

0869 LiteOn 1058, 1158, 1416,

1440 Loewe 0511 Magnavox 0503, 0539, 0646,

0675, 0821 Malata 0782, 1159 Marantz 0539 McIntosh 1533 Memorex 0695, 0831, 1270 Microsoft 0522 Mintek 0717, 0839 Mitsubishi 0521, 1521 Momitsu 1082 NAD 0591, 0692, 0741 NEC 0785 Nesa 0717 Next Base 0826 NexxTech 1402 Norcent 0872, 1003, 1107,

1265 Onkyo 0503, 0627, 0792 Oritron 0651 Panasonic 0490, 0503, 0703,

1362, 1462, 1490,

1762 Philips 0503, 0539, 0646,

0675, 1267, 1354 PianoDisc 1024 Pioneer 0525, 0571, 0631 Polaroid 1020, 1061, 1086 Polk Audio 0539 Portland 0770 Presidian 0675 Proceed 0672 Proscan 0522 ProVision 0778 Qwestar 0651 RCA 0522, 0571, 0717,

0790, 0822 Rio 0869 RJTech 1360 Rotel 0623 Rowa 0823 Sampo 0698, 0752 Samsung 0490, 0573, 0744,

0820, 1044, 1075 Sansui 0695 Sanyo 0670, 0695, 0873 Sensory Science 1158

Sharp 0630, 0675, 0752,

1256 Sharper Image 1117 Sherwood 0633, 0770, 1043,

1077 Shinsonic 0533, 0839 Sonic Blue 0869, 1099 Sony 0533, 0864, 1033,

1431, 1533 Sungale 1074 Superscan 0821 SVA 0860, 1105 Sylvania 0675, 0821 Symphonic 0675 Teac 0790, 0809 Technics 0490, 0703 Technosonic 0730 Techwood 0692 Theta Digita 0571 Toshiba 0503, 0695, 1154,

1854 Tredex 0800, 0803, 0804 Urban Concepts 0503 US Logic 0839 Venturer 0790 Vizio 1064, 1226 Xbox 0522 Yamaha 0490, 0539, 0545 Yamakawa 0872 Zenith 0503, 0591, 0741,

0869 Zoece 1265

VCRs

Brand Code

ABS 1972 Admiral 0048, 0209, 0479 Adventura 0000 Aiko 0278 Aiwa 0000, 0037, 0124 Akai 0041, 0061, 0175 Alienware 1972 America Action 0278 American High 0035 Asha 0240 Audiovox 0037, 0278 Beaumark 0240 Bell & Howell 0104 Broksonic 0002, 0121, 0184,

0209, 0479 Calix 0037 Canon 0035 Carver 0081 CCE 0072, 0278 Citizen 0037, 0278 Colt 0072 Craig 0037, 0047, 0072,

0240 Curtis Mathes 0035, 0041, 0060,

0162 Cybernex 0240 CyberPower 1972 Daewoo 0045, 0278 Dell 1972 Denon 0042

DirecTV 0739 Durabrand 0038, 0039 Dynatech 0000 Electrohome 0037, 0043 Electrophonic 0037 Emerex 0032 Emerson 0000, 0002, 0037,

Fisher 0047, 0104 Fuji 0033, 0035 Funai 0000, 0593, 1593 Garrard 0000 Gateway 1972 GE 0035, 0060, 0065,

Go Video 0240, 0432, 0526 GoldStar 0037, 0038 Gradiente 0000 Harley Davidson 0000 Harman/Kardon 0038, 0075, 0081 Harwood 0072 Headquarter 0046 Hewlett Packard 1972 HI-Q 0047 Hitachi 0000, 0041, 0042,

Howard Computers 1972 HP 1972 Hughes Network Systems Humax 0739 Hush 1972 iBUYPOWER 1972 Jensen 0041 JVC 0008, 0041, 0067 KEC 0037, 0278 Kenwood 0038, 0041, 0067 KLH 0072 Kodak 0035, 0037 Linksys 1972 Lloyd's 0000 Logik 0072 LXI 0037 Magnasonic 0593 Magnavox 0000, 0035, 0039,

Magnin 0240 Marantz 0035, 0081 Marta 0037 Matsushita 0035, 0162 Media Center PC 1972 MEI 0035 Memorex 0000, 0035, 0037,

MGA 0043, 0061, 0240 MGN Technology 0240 Microsoft 1972 Mind 1972 Minolta 0042, 0105

0043, 0061, 0121, 0184, 0209, 0212, 0278, 0479, 0593, 1593

0240, 0807

0065, 0089, 0105

0042, 0739

0081, 0149, 0563, 0593

0039, 0046, 0047, 0048, 0104,

0162, 0209, 0240, 0479

(continued)

Chapter 2: Using the remote control

Mitsubishi 0043, 0061, 0067,

0075, 0173, 0807 Motorola 0035, 0048 MTC 0000, 0240 Multitech 0000, 0072 NEC 0038, 0040, 0041,

0067, 0104 Nikko 0037 Nikon 0034 Niveus Media 1972 Noblex 0240 Northgate 1972 Olympus 0035, 0226 Onkyo 0222 Optimus 0037, 0048, 0104,

0162, 0432, 0593,

1062 Orion 0002, 0184, 0209,

0479 Panasonic 0035, 0077, 0162,

0225, 0226, 0616,

1062 Penney 0035, 0037, 0038,

0040, 0042, 0240 Pentax 0042, 0065, 0105 Philco 0035 Philips 0035, 0081, 0618,

0739, 1081, 1181 Pilot 0037 Pioneer 0067 Polk Audio 0081 Profitronic 0240 Proscan 0060 Protec 0072 Pulsar 0039 Quarter 0046 Quartz 0046 Quasar 0035, 0077, 0162 RadioShack 0000 Radix 0037 Randex 0037 RCA 0042, 0060, 0065,

0077, 0105, 0149,

0240, 0807,

0880 Realistic 0000, 0035, 0037,

0046, 0047, 0048,

0104 ReplayTV 0614, 0616 Ricavision 1972 Ricoh 0034 Runco 0039 Salora 0075 Samsung 0045, 0240, 0739 Sanky 0039, 0048 Sansui 0000, 0041, 0067,

0209, 0479 Sanyo 0046, 0047, 0104,

0159, 0240 Scott 0043, 0045, 0121,

0184, 0210, 0212 Sears 0000, 0035, 0037,

0042, 0046, 0047,

0104, 0105 Sharp 0048, 0807, 0848 Shintom 0072 Shogun 0240

Singer 0072 Sonic Blue 0614, 0616 Sony 0000, 0032, 0033,

0034, 0035, 0636,

1032, 1972 Stack 9 1972 STS 0042 Sylvania 0000, 0035, 0043,

0081, 0593, 1593 Symphonic 0000, 0593, 1593 Systemax 1972 Tagar Systems 1972 Tatung 0041 Teac 0000, 0041 Technics 0035, 0162 Teknika 0000, 0035, 0037 Thomas 0000 Tivo 0618, 0636, 0739,

1996 TMK 0240 Toshiba 0043, 0045, 0209,

0210, 0212, 0366,

0845, 1008,

1145, 1972, 1996 Totevision 0037, 0240 Touch 1972 Unitech 0240 Vector 0045 Vector Research 0038, 0040 Video Concepts 0040, 0045, 0061 Videomagic 0037 Videosonic 0240 Viewsonic 1972 Villain 0000 Voodoo 1972 Wards 0000, 0035, 0042,

0047, 0048, 0060,

0072, 0081,

0149, 0212, 0240 White Westinghouse 0072, 0209 XR-1000 0000, 0035, 0072 Yamaha 0038 Zenith 0000, 0033, 0034,

0039, 0209, 0479,

1139 ZT Group 1972

PVRs

Brand Code

ABS 1972 Alienware 1972 CyberPower 1972 Dell 1972 Direc TV 0739 Gateway 1972 Hewlett Packard 1972 Howard Computers 1972 HP 1972 Hughes Network Systems 0739 Humax 0739 Hush 1972 iBUYPOWER 1972 Linksys 1972 Media Center PC 1972

Microsoft 1972 Mind 1972 Niveus Media 1972 Northgate 1972 Panasonic 0616 Philips 0618, 0739 RCA 0880 ReplayTV 0614, 0616 Sonic Blue 0614, 0616 Sony 0636, 1972 Stack 9 1972 Systemax 1972 Tagar Systems 1972 Tivo 0618, 0636, 0739 Toshiba 1008, 1972 Touch 1972 Viewsonic 1972 Voodoo 1972 ZT Group 1972

Cable/PVR combos

Brand Code

Americast 0899 Digeo 1187 Motorola/

General Instrument/ Jerrold 0476, 0810 Motorola 1187, 1376

Pace 0237, 1877 Pioneer 0877, 1877 Scientific Atlanta 0877, 1877 Sony 1006 Supercable 0276 Zenith 0899

DBS/PVR combos (1)

Brand Code

DirecTV 0099, 0392, 0639,

1076, 1142, 1377, 1392, 1442,

1443, 1444, 1640 Dish Network System 0775, 1505 Dishpro 0775, 1505 Echostar 0775, 1170, 1505 Expressvu 0775 Hughes Network

Systems 1142, 1442, 1443,

1444 JVC 1170 Motorola 0869 Philips 1142, 1442 Proscan 0392 RCA 1392 Samsung 1442 Sony 0639, 1640 Star Choice 0869

DBS/PVR combos (2)

Brand Code

Hughes Network Systems 0739 Philips 0739

Samsung 0739

Chapter 2: Using the remote control

Audio Amps

Brand Code

Adcom 0577, 1100 Bose 0674 Carver 0892 Durabrand 1561 Elan 0647 GE 0078 Harman/Kardon 0892 JVC 0331 LeftCoast 0892 Lenoxx 1561 Luxman 0165 Marantz 0321, 0892 McIntosh 0251 Nakamichi 0321 NEC 0264 Optimus 0395, 0823 Parasound 0246 Philips 0892 Pioneer 0823 PolkAudio 0892 RCA 0823 Realistic 0395 Sansui 0321 Shure 0264 Sony 0689, 0815, 1126 Soundesign 0078, 0211 Victor 0331 Wards 0078, 0211 Yamaha 0133, 0143, 0354,

0504

CD players

Brand Code

Adcom 0234 Aiwa 0124, 0157 Akai 0156 Arcam 0157 Audio-Technica 0170 Burmester 0420 California Audio Labs 0029, 0303 Carver 0157, 0299 Denon 0003, 0034 DKK 0000 DMX Electronics 0157 Garrard 0393, 0420 Genexxa 0032 Harman/Kardon 0083, 0157, 0173 Hitachi 0032, 0139 Integra 0101 JVC 0072, 0655, 1294 Kenwood 0028, 0037, 0190,

0626 Krell 0157 Linn 0157 Magnavox 0038, 0157 Marantz 0029, 0038, 0157,

0180, 0435, 0626 MCS 0029 MGA 0083 Miro 0000 Mission 0157 Mitsubishi 0083

MTC 0420 NAD 0019, 0299 NEC 0234 Nikko 0170 NSM 0157 Onkyo 0101, 0102, 0138,

0381, 1327

Optimus 0000, 0032, 0037,

0087, 0420, 0468

Panasonic 0029, 0303, 0388,

0752 Parasound 0420 Philips 0157, 0274, 0626 Pioneer 0032, 0468, 0551,

1062, 1087 Polk Audio 0157 Proceed 0420 Proton 0157 QED 0157 Quad 0157 Quasar 0029 RCA 0032, 0053, 0420,

0468, 1062 Realistic 0180, 0420 Rotel 0157, 0420 SAE 0157 Sansui 0157 Sanyo 0087 Sharp 0037, 0180 Sherwood 0180 Sonic Frontiers 0157 Sony 0000, 0100, 0185,

0490, 0604, 0605,

0673, 1364 Sugden 0157 TAG McLaren 0157 Tascam 0420 Teac 0180, 0378, 0393,

0420 Technics 0029, 0303 Toshiba 0019, 0299 Victor 0072 Wards 0053, 0157 Yamaha 0036, 0170, 0187,

0490, 1292

Audio Amps/Tuners

Brand Code

ADC 0531 Aiwa 0121, 0189, 1243,

1388, 1405, 1641 Akai 1255, 1512 Alco 1390 AMC 1077 Anam 1074, 1609 Apex Digital 1774 Arcam 1189 Audiotronic 1189 Audiovox 1390 Bose 0639, 1229, 1253,

1933 Capetronic 0531 Carver 0121, 0189, 1189,

1289 Delphi 1414 Denon 0121, 1142, 1360

Fisher 1801 Harman/Kardon 0110, 0189, 0891,

1289, 1304, 1306 Hitachi 1273, 1801 Integra 0135, 1298, 1320 JBL 0110, 1306 JVC 1058, 1374, 1495,

1811 Kenwood 0186, 1313, 1569,

1570 KLH 1390, 1428 Linn 0189 Magnavox 0189, 0531, 1189,

1269, 1514 Marantz 0189, 1189, 1269,

1289 McIntosh 1289 Micromega 1189 Mitsubishi 1393 Myryad 1189 Nakamichi 1313 Onkyo 0135, 0380, 0842,

1298, 1320, 1531 Optimus 0186, 0531, 1023,

1074 Panasonic 0309, 1288, 1308,

1316, 1350, 1363,

1518, 1548,

1633, 1763, 1764 Philips 0189, 1189, 1266,

1269 Pioneer 0014, 0150, 0531,

0630, 1023, 1384 Polk Audio 0189, 1289, 1414 Proscan 1254 RCA 0531, 1023, 1074,

1254, 1390, 1511,

1609 Samsung 1295, 1304, 1500 Sansui 0189, 1189 Sanyo 1469, 1801 Sharp 0186 Sherwood 1077 Sirius 1811 Sony 0168, 1058, 1258,

1406, 1441, 1558,

1622, 1658,

1758, 1759, 1858 Stereophonics 1023 Sunfire 1313 Teac 1074, 1267, 1390,

1528 Technics 0309, 1308, 1518,

1633 Thorens 1189 Toshiba 0135 Venturer 1390 Wards 0014, 0189 XM 1406, 1414 Yamaha 0176, 0186, 1176,

1276, 1331, 1375

Chapter 3: Menu layout and navigation

Main menu layout

The tables below and on the next page provide a quick overview of your TV’s menu system. To open the main menus (illustrated below), press Y on the remote control or TV control panel.

Icon Item Option

Applications

Video

Audio

Preferences

Locks

Setup

Picture Viewer S [Launches the JPEG Picture Viewer] Audio Player S [Launches the MP3 Audio Player] Personal E-mail S [Launches the Personal E-mail] Channel Browser TV Guide On Screen

Digital CC/Audio Selector CableCARD

™

S [Launches the Channel Browser™] S [Opens the TV Guide On Screen™ feature] S [Launches the ATSC Digital CC Selector] (This feature is not available

if the TV is not tuned to a digital channel).

™

S Dynamic list of items provided by Cable company.

(This option is not available if a CableCARD Mode S Sports/Standard/Movie/Preference/Pro 1/Pro 2 Picture Settings S [Opens the Picture Settings menu] Noise Reduction S [Opens the Noise Reduction menu] Color Management Pro S [Opens the Color Management Pro menu] Game Mode S On/Off Theater Settings S [Opens the Theater Settings menu] Audio Settings S [Opens the Audio Settings menu] Advanced Audio Settings S [Opens the Advanced Audio Settings menu]

Audio Setup S [Opens the Audio Setup menu] Closed Caption Mode S OFF/CC1/CC2/CC3/CC4/T1/T2/T3/T4

Closed Caption Advanced S [Opens the Closed Caption Advanced menu] Input Labeling S [Opens the Input Labeling menu] Menu Language S English/French/Spanish Channel Browser Setup S [Opens the Channel Browser Setup menu] Enable Rating Blocking S Off/On Edit Rating Limits S [Opens the Edit Rating Limits menu] Channels Block S [Opens the Channels block menu] Input Lock S Off/Video/Video+ Front Panel Lock S Off/On GameTimer

™

S Off/30 Min/60 Min/90 Min/120 Min New PIN Code S [Opens the New PIN Code entry screen] Installation S [Opens the Installation menu (- page 23)] Sleep Timer S [Opens the Sleep Timer menu] On/Off Timer S [Opens the On/Off Timer menu] PC Settings S [Opens the PC Settings menu] PC Audio S No/Yes HDMI 1 Audio S Auto/Digital/Analog Slide Show Interval S 2 Sec/5 Sec/10 Sec/15 Sec/20 Sec

™

is not inserted.)

Chapter 3: Menu layout and navigation

Setup/Installation menu layout

The Installation menu contains the Terrestrial, Network, TV Guide On Screen™ Setup, Time and Date, and System Status menus (as described below).

To open the Installation menu (illustrated below), press Y on the remote control or TV control panel, open the Setup menu, select Installation, and press T.

Icon Item Option

Press Y, open the Setup menu, and then open the Installation sub-menu.

Terrestrial

Network

Input Configuration S [Opens the Input Configuration menu] Channel Program

S ANT1 S [Scans for new channels on ANT1] S ANT2 S [Scans for new channels on ANT2]

Channel Add/Delete S [Opens the Channel Add/Delete menu] Signal Meter S [Opens the Signal Meter menu] Basic Network Setup S [Opens the Basic Network Setup menu] Personal E-mail Setup S [Opens the Personal E-mail Setup menu] E-mail Scheduling Setup S [Opens the E-mail Scheduling Setup menu] Home File Server Setup S [Opens the Home File Server Setup menu] Software Upgrade S [Opens the Software Upgrade menu]

TV Guide On Screen™ Setup

Time and Date

System Status

Start

S [Opens the TV Guide On Screen

menu]

™

Setup

Start Setup S [Opens the Time and Date Setup menu]

System Information S [Opens the System Information screen]

Chapter 3: Menu layout and navigation

THINC™ menu layout

The THINC* menu provides access to the Picture Viewer, Audio Player, Personal E-mail, Channel Browser, Favorites Browser, and TV Guide On Screen features.

The THINC menu is not part of the main menu system. You can only view the THINC menu by pressing C on the remote control.

THINC Applications

Picture Viewer

Audio Player

Personal E-mail

Channel Browser

Favorites Browser

TV Guide On Screen

Navigate

* Toshiba Home Interactive Network Connection.

ENTER

Select

EXIT

Exit

Navigating the menu system

You can use the buttons on the remote control or TV control panel to access and navigate your TV’s on-screen menu system.

• Press Y to open the menu system.

• When a menu is open, use the up/down/left/right arrow

buttons (BbC c) on the remote control or TV control panel to move in the corresponding direction in the menu.

• Press T to save your menu settings or select a highlighted

item. (A highlighted menu item appears in a different color in the menu.)

• All menus close automatically if you do not make a selection

within 60 seconds, except the signal meter menu, which closes automatically after about 5 minutes.

• To close a menu instantly, press O.

Note:

• The menu backgrounds may sometimes appear black, depending on the signal the TV is receiving. This is not a sign of malfunction.

Applications

Picture Viewer

Audio Player

Personal E-mail

Channel Browser

TV Guide On Screen

Digital CC/Audio Selector

CableCARD

Navigate

• The Video sub-menu appears with a black background, which looks different from other menus.

Picture Settings

Contrast 100

Back Light 100

Brightness

Color

Tint

Sharpness

Advanced Picture Settings

Reset

Select

Back Exit

CH RTNENTER

Done

EXIT

Mode: Sports

Chapter 4: Setting up your TV

Selecting the menu language

You can choose from three different languages (English, French, and Spanish) for the on-screen display of menus and messages.

Note: The TV Guide On Screen™ menus are in English, regardless of the language selected in this menu.

To select the menu language:

1 Press Y and open the Preferences menu. 2 Highlight Menu Language and press c. 3 Press B or b to select your preferred menu language and

press T.

Preferences

Closed Caption Mode

Closed Caption Advanced

Input Labeling

Menu Language English

Channel Browser Setup

Navigate

4 Press O to close the Preferences menu.

Off

Select

English

Français

Español

Back Exit

CH RTNENTER

EXIT

Configuring the antenna input sources for the ANT 1 and ANT 2 terminals

To configure the ANT 1 and ANT 2 input sources:

1 Press Y and open the Setup menu. 2 Highlight Installation and press T.

Setup

Installation

Sleep Timer

On/Off Timer

PC Settings

PC Audio HDMI 1 Audio

Slide Show Interval

Navigate

3 (A new set of Installation menu icons will appear on-

screen, as shown below.) Open the Terrestrial menu, highlight Input Configuration, and press T.

Note: The Terrestrial menu may not be accessible (items will be “grayed out”) in some instances (for example, if a cable box is connected to the ANT 1 input or if one of the VIDEO modes is the current input during TV Guide On Screen

™

setup).

Select

Auto

2 Sec

CH RTNENTER

Back Exit

EXIT

Terrestrial

Input Configuration

Channel Program

Channel Add/Delete

Signal Meter

Navigate

Select

Back Exit

CH RTNENTER

EXIT

4 Press B or b to highlight Antenna 1 In, and then press

C or c to select the input source (Cable or Antenna) for

the ANT 1 input on the TV.

Note: If a cable box is connected to the ANT 1 input during TV Guide On Screen menu will not be accessible, including the input source for ANT 1, which will automatically display “Cable Box.”

™

setup, the entire Terrestrial

5 Press b to highlight Antenna 2 In and then C or c to

select the input source (Cable or Antenna) for the ANT 2 input on the TV, if applicable. If you have not connected anything to the ANT 2 input, skip this step.

Input Configuration

Antenna 1 In

Antenna 2 In

Cancel Done

Cable

Antenna

6 To save your new settings, highlight Done and press T.

To revert to your original settings, highlight Cancel and press T.

Chapter 4: Setting up your TV

Programming channels into the TV’s channel memory

When you press < or , on the remote control or TV control panel, your TV will stop only on the channels you programmed into the TV’s channel memory.

Follow the steps below to program channels into the TV’s channel memory.

Programming channels automatically

Your TV can automatically detect all active channels in your area and store them in its memory. After the channels are programmed automatically, you can manually add or erase individual channels in the channel memory.

Note:

• You must configure the antenna input source before

programming channels (- page 25).

• If the Antenna 1 input signal type is set to Cable, the automatic channel programming process erases channels that were previously programmed into the TV’s memory.

• If the Antenna 1 input signal type is set to Antenna, the automatic channel programming process adds newly found channels to the existing set of programmed channels (and does NOT erase channels that were previously programmed into the TV’s memory). To remove an antenna source channel from the memory, you must manually delete it.

• To tune the TV to a channel not programmed in the channel memory, you must use the Channel Number buttons on the remote control.

• Programming channels when the antenna input is configured for Cable will take substantially longer than when the antenna input is configured for Antenna. This is normal; however, once channel programming is finished, you should not have to repeat the programming process again unless your Cable TV service lineup changes significantly.

™

• If you have a CableCARD for the ANT 1 input is disabled because the CableCARD automatically loads the Cable channel list into the TV’s channel memory. See the Installation Guide for details on

™

CableCARD

inserted, channel programming

™

To program channels automatically:

1 Configure the antenna input sources, if you have not

already done so (

- page 25).

2 Press Y and open the Setup menu. 3 Highlight Installation and press T.

Setup

Installation

Sleep Timer

On/Off Timer

PC Settings

PC Audio HDMI 1 Audio

Slide Show Interval

Navigate

Select

Auto

2 Sec

CH RTNENTER

Back Exit

EXIT

4 (A new set of Installation menu icons will appear, as

shown below.) Open the Terrestrial menu, highlight Channel Program, and press T.

Terrestrial

Input Configuration

Channel Program

Channel Add/Delete

Signal Meter

Navigate

Select

Back Exit

CH RTNENTER

EXIT

5 Highlight ANT 1 (or ANT 2) and then press T to start

automatic channel programming.

ANT 1 Antenna Scanning channels, please wait ...

Abort

The TV will automatically cycle through all the antenna channels, and store all active channels in the channel memory. While the TV is cycling through the channels, the message “Scanning channels, please wait” appears (as shown above).

6 To cancel channel programming, press O on the remote

control (or highlight Abort in the on-screen display and press T).

When channel programming is finished, press < or , to view the programmed channels.

52%

Chapter 4: Setting up your TV

Manually adding and deleting channels in the channel memory

After automatically programming channels into the channel memory, you can manually add or delete individual channels.

To add or delete channels in the channel memory:

1 Press Y and open the Setup menu. 2 Highlight Installation and press T. 3 (A new set of Installation menu icons will appear, as

shown below.) Open the Terrestrial menu, highlight Channel Add/Delete, and then press T.

Terrestrial

Input Configuration

Channel Program

Channel Add/Delete

Signal Meter

Navigate

Select

Back Exit

CH RTNENTER

EXIT

4 The illustration below left shows channels programmed

for the ANT 1 antenna input. To view the list of channels programmed for the ANT 2 or Cable box antenna input, press Bb to highlight ANT 2 and press T.

Channel Add/Delete

2 - 1

2 - 2

7 - 1

Analog ANT 1

Digital

Analog

Digital

Analog

ANT 2

Reset

Cancel

Done

Channel Add/Delete

Analog ANT 1

ANT 2

Analog

Reset

Analog

Cancel

Analog

Done

To remove a channel from the channel memory:

Highlight the checked box next to the channel number you want to remove, and then press T to uncheck the box.

To save your new settings:

Highlight Done and press T.

To revert to your original settings:

Highlight Cancel and press T before saving.

To remove all channels from the channel memory:

Highlight Reset and press T, and then highlight Done and press T.

Channel Add/Delete

2 - 1

2 - 2

7 - 1

Note: This action applies to the current antenna input only. To delete/add channels on the other input, highlight the other input and press T.

Analog ANT 1

Digital

Analog

Digital

Analog

Digital

Analog

ANT 2

Reset

Cancel

Done

To add a channel to the channel memory:

Highlight the unchecked box next to the channel number you want to add, and then press T to check the box.

To manually add digital subchannels on a physical channel:

Use the Channel Numbers and the Dash (=) on the remote control to enter the channel number (for example, 56–1).

If the channel is found, the number will be added to the list and the box will be checked.

If the channel is not found, a message will appear.

Chapter 4: Setting up your TV

Setting the time and date

Note: If you already set up the TV Guide On Screen™ system, the time and date were set automatically and you can skip this step.

To set the time and date:

1 Press Y and open the Setup menu. 2 Highlight Installation and press T. 3 (A new set of Installation menu icons will appear, as

shown below.) Open the Time And Date menu, highlight Start Setup, and press T.

Time And Date

Start Setup

Navigate

If you have not set up the TV Guide On Screen the following screen will appear. To set the time, highlight

TV Guide On Screen

On Screen

™

setup sequence will start, and the time and

date will be set automatically.

Time And Date

Your TV Guide On Screen system can provide accurate

time and date information.

It is recommended you set up TV Guide On Screen

first and use it to obtain the time and date.

Manual

TV Guide On Screen

If you have already set up the TV Guide On Screen system, or if you have not set up the time, the Time and Date setting screen will appear and you will need to manually set the time and date.

Back Exit

CH RTNENTER

Select

™

and press T. The TV Guide

EXIT

Cancel

™

system,

™

Setting the HDMI™ audio mode

To set the HDMI audio mode:

1 Press Y and open the Setup menu. 2 Highlight HDMI 1 Audio and press c. 3 Press b or B to select the HDMI audio mode (Auto,

Digital, or Analog) and press T. (Auto is the

recommended mode.) See “Connecting an HDMI or DVI device to the HDMI input” (- Installation Guide).

Setup

Installation

Sleep Timer

On/Off Timer

PC Settings

PC Audio

HDMI 1 Audio

Slide Show Interval

Navigate

Select

Note: Because the PC IN and HDMI (DVI) IN inputs share the same set of analog audio inputs, the PC Audio menu setting influences the HDMI 1 Audio menu setting. If PC Audio is set to “No,” the HDMI 1 Audio setting changes to “Auto.” If PC Audio is set to “Yes,” the HDMI Audio setting is set to “Digital” and is grayed out in the menu. (Also see item 4 on page 9 and “Setting the PC Audio mode” on page 52.)

Auto

2 Sec

CH RTNENTER

Auto

Digital

Analog

Back Exit

EXIT

Time And Date

Date (MM/DD/YY)

Time (HH:MM)

In the event that your TV Guide On Screen system

has acquired time, the television will use network

acquired time rather than manually enterred time.

Cancel

Done

/06 30/05

:11 11

Note:

™

• If you highlight TV Guide On Screen time and date through the TV Guide On Screen

(above) to set the

™

system and a power outage occurs, the time and date will be updated automatically when the power is restored.

• If you highlight Manual (above) to set the time and date manually and a power outage occurs, you will lose the time and date settings when the power is restored.

• If you manually set the time and date and then perform

™

TV Guide On Screen

setup, the manual time and date settings will be overridden by the TV Guide On Screen settings.

™

Chapter 4: Setting up your TV

Viewing the CableCARD™ menu

A CableCARD™ enables you to view encrypted digital channels. For connection and subscription information, see “Connecting a digital CableCARD

Guide.

Note: Connecting your TV directly to the Audio/Video output of your set-top box may provide a more vivid picture.

After the CableCARD™ is inserted, a CableCARD™ option appears in the Applications menu, with informational screens provided by your digital CableCARD the sample illustration under step 3, below).

CableCard Connected -- Acquiring channel information.

CableCard services will only operate with cable signal connected to Antenna 1.

To view the CableCARD™ menu:

1 Press Y and open the Applications menu. 2 Highlight CableCARD 3 Press B or b to select one of the side menu items and then

press T to display the information.

Applications

Picture Viewer

Audio Player

Personal E-mail

Channel Browser

TV Guide On Screen

Digital CC/Audio Selector

CableCARD

Navigate

™

and press c.

IP Service

Conditional Access

CableCARD(tm) Status

Network Setup

CableCARD(tm) Pairing

Back Exit

CH RTNENTER

Select

” in the Installation

™

service (see

EXIT

Viewing the digital signal meter

You can view the digital signal meter for the ANT 1 and ANT 2 digital TV input sources only.

To view the digital signal meter:

1 Press Y and open the Setup menu. 2 Highlight Installation and press T. 3 A new set of Installation menu icons will appear, as shown

below. Open the Terrestrial menu, highlight Signal Meter,

and press T.

4 Press BbC c to select the antenna input and digital

channel whose signal you want to check.

Note: The physical digital channel number listed in the Signal Meter screen may not correspond to a virtual TV channel number. Contact your local broadcasters to obtain the RF channel numbers for your local digital stations.

Note: The CableCARD™ menu is for informational purposes only and has no user-adjustable options.

To close the screen and return to the Terrestrial menu:

Highlight Done and press T.

To return to normal viewing:

Press O.

Chapter 4: Setting up your TV

Viewing the system status

To view the system status:

1 Press Y and open the Setup menu. 2 Highlight Installation and press T. 3 A new set of Installation menu icons will appear, as shown

below right. Open the System Status menu, highlight System Information, and press T.

Setup

Installation

Sleep Timer

On/Off Timer

PC Settings

PC Audio

HDMI 1 Audio

Slide Show Interval

Navigate

Select

Auto

2 Sec

CH RTNENTER

Back Exit

EXIT

4 Press C c to scroll through the menu bar to select either

Product Information or Software Version and view

the related information.

System Information

Product Information

Brand:

Toshiba

Model:

42LZ196

Done

System Status

System Infomation

Navigate

System Information

Jun 20 2006 - 15:05:15

CH RTNENTER

Select

Software Version

2.3.55.0

FW: 37

Done

Back Exit

EXIT

Reset Factory Defaults

To reset all settings and channels to their factory default values:

1 Press Y and open the Setup menu. 2 Highlight Installation and press T. A new set of

Installation menu icons will appear.

3 Open the System Status menu, highlight System

Information, and press T.

4 Press C c to scroll through the menu bar to select

Factory Defaults.

5 Enter your PIN code (or 0000 if no PIN code has been set). 6 Highlight Yes and press T. The TV will turn off

automatically after a few seconds. After the TV turns off, unplug the TV power cord and then plug it in again to complete the reset process.

System Information

Press YES to confirm. After the TV turns off, unplug it and plug it back in to complete the reset.

YesNo

To cancel the reset:

Highlight No and press T.

To close the screen and return to the Installation menu:

Highlight Done and press T.

To return to normal viewing:

Press O.

Chapter 5: Using the TV’s features

Selecting the video input source to view

The video inputs available to view will be determined by the input terminals you used to connect your devices (see the Installation Guide).

To select the video input source to view:

1 Press + on the remote control or TV control panel. 2 And then either:

a) Press 0-8; or b)Repeatedly press Bb on the remote control (or

CHANNEL Bb on the control panel) to change the input; or

c) Repeatedly press + on the remote control or TV

control panel to change the input.

The current signal source displays in the top right corner of the Input Selection screen.

Input Selection ANT 1

ANT 1ANT 1

Video 1

Video 2

ColorStream HD1

ColorStream HD2

HDMI 1

HDMI 2

ANT 2

INPUT

- / to Select

Note:

• You can label the video input sources according to the specific devices you have connected to the TV (- “Labeling the video input sources” at right).

• The source can be “hidden” (- “Labeling the video input sources” at right).

Labeling the video input sources

You can label each video input source to describe the type of device you connected to each source. You can choose from the following preset list of labels:

• “– –” (default label)

• Cable

• DTV

• Satellite/DSS

• VCR

• Laser Disk

• DVD

• HD DVD

• Audio Receiver

• Compact Disc

• Video Recorder

• Game Console

• Hide (to skip over an unused input in the Input Selection

screen)

Note:

• If you select ANT 2 in the Input selection screen, you can choose only “– –” or “Hide” as the label.

• If you select PC in the Input Selection screen, you can choose only “– –,” “Hide,” or “Game Console” as the label.

To label the video input sources:

1 Press Y and open the Preferences menu. 2 Highlight Input Labeling and press T. 3 Press B or b to highlight the video source you want to

label.

Preferences

Closed Caption Mode

Closed Caption Advanced

Input Labeling

Menu Language English

Channel Browser Setup

Off

Navigate

Input Labeling

Video 1 DVD

Video 2 Cable

ColorStream HD 1 Video Recorder

ColorStream HD 2 Hide

HDMI 1 DTV

HDMI 2 Satellite/DSS

ANT 2

Reset

Select

Back Exit

CH RTNENTER

Done

EXIT

4 Press C or c to select the desired label for that input

source. If a particular input is not used, you can select Hide as the label, which will cause that input to be “grayed out” in the Input Selection screen and skipped over when you press + on the remote control.

(continued)

Chapter 5: Using the TV’s features

5 To save the new input labels, highlight Done and

press T. To revert to the factory default labels, highlight Reset and press T.

Input labeling example:

The screen below left shows the default Input Selection screen (with none of the inputs labeled as a specific device). The screen below right is an example of how you could label the inputs if you connected a DVD player to VIDEO 1, Cable TV to VIDEO 2, a video recorder to ColorStream HD1, a DTV set-top box to HDMI 1, and a satellite/DSS set-top box to HDMI 2. Also note that the ColorStream HD2 input is labeled “Hidden,” which means that input will be skipped over when + is pressed.

Input Selection ANT 1

ANT 1ANT 1

Video 1

Video 2

ColorStream HD1

ColorStream HD2

HDMI 1

HDMI 2 PC

ANT 2

INPUT

- / to Select

Input Selection screen with no inputs labeled.

To clear the input labels:

Input Selection ANT 1

ANT 1ANT 1

DVD

Cable

Video Recorder

ColorStream HD2 (Hidden)

DTV

Satellite/DSS PC

ANT 2

INPUT

- / to Select

Input Selection screen with all inputs labeled except input 4, which has been hidden.

Tuning channels

Tuning channels using the Channel Browser

The Channel Browser™ provides an easy navigation interface for all your channels and inputs. This feature allows you to:

• Navigate the contents of all of your inputs.

• Keep a list of your favorite channels (see “Favorite

Browser,” below).

• Provide Cable Box and Satellite Box lists.

• Keep a history of the last 32 channels or inputs viewed.

• Quickly surf and tune your recently viewed channels/inputs

from the Channel Browser next page).

• Surf via Browse mode (to immediately tune channels as you

highlight them in the Channel Browser surf over channels in the Channel Browser select one to tune).

• Quickly change inputs from the Inputs List.

Favorite Browser

The Favorite Browser allows you to quickly set up a favorite channels/inputs list that is integrated into the Channel Browser

™

History List (illustrated on the

™

) or Select mode (to

™

before you

™

1 Press Y and open the Preferences menu. 2 Highlight Input Labeling and press T. 3 Highlight Reset and press T.

To add a favorite channel/input:

1 Tune to the channel or input. 2 Press and hold n for 3 seconds.

Note: Additions are added to the beginning of the Favorite list on the left side of the Channel Browser

To delete a favorite channel/input:

™

1 Press n to open the Favorite browser list. 2 Highlight the channel or input to delete by pressing

3 C or # c.

3 Press and hold = for 3 seconds. The channel/input will

be removed from the Favorite list.

Picture Preview

• A small thumbnail preview of the current channel or input

will appear in the list.

• Picture snapshots will be taken when a source change occurs

from the Channel Browser

• Up to 32 picture previews can be stored in the Channel

Browser

™

across all lists. If you add a new picture when the total = 32, the oldest thumbnail will be deleted. One thumbnail is counted only once against the total, no matter how many times it appears in various lists.

• Turning off the TV deletes all of the current thumbnails.

™

Chapter 5: Using the TV’s features

To set up the Channel Browser™:

1 Press Y and open the Preferences menu. 2 Highlight Channel Browser Setup and press T. 3 Press B to highlight Navigation, and then press C or c

to select either Browse Mode or Select Mode.

Channel Browser Setup

Navigation

History List

ANT1 List On

ANT2 List On

Cable Box List Off

Satellite Box List On

Inputs List On

Favorites List On

Reset

Select Mode

Power Off Clear (On)

Done

4 Press b to highlight History List, and then press C or c

to select the setting you prefer: either Power Off Clear (On), On, or Off.

Note: When History List is set to On, the channels and inputs stored in the list will be saved every power on/off cycle. When History List is set to Power Off Clear (On), the channels and inputs stored in the list will be cleared with every power on/off cycle of the TV.

5 Press b to highlight ANT1 List, and then press C or c to

select On or Off.

6 Press b to highlight ANT2 List, and then press C or c to

select On or Off.

7 Press b to highlight Cable Box List, and then press C or

c to select On or Off.

8 Press b to highlight Satellite Box List, and then press

C or c to select On or Off.

9 Press b to highlight Inputs List, and then press C or c

to select On or Off.

10 Press b to highlight Favorites List, then press C or c to

select On or Off.

11 To save your entries, highlight Done and press T.

To return to factory defaults, highlight Reset and press T.

Note: Cable Box List and Satellite Box List will be grayed out and set to Off by default. They will remain this way until a Cable Box and/or Satellite Box is configured from the TV Guide setup.

To open the Channel Browser™:

• Press 3 C, # c, or n on the remote control.

• Press 3 C to surf backward through the currently selected

list.

• Press # c to surf forward through the currently selected list.

Note: The Channel Browser™ is not available while the TV is in POP mode.

Elements of the Channel Browser

™

1 Input type 2 Highlighted item (channel or input) 3 Channels with thumbnails stored in the History List 4 Current list (History, ANT 1, ANT 2, Cable Box,

Satellite Box, Inputs, or Favorites)

5 Current input 6 Current antenna type (cable or TV) 7 Active channel number

8 Channel call letters (if available)

9 Resolution

To toggle among the available lists:

After opening the Channel Browser™, press B or b to toggle among History, ANT 1, ANT 2, Cable Box, Satellite Box, Inputs and Favorites.

Note:

• The Channel Browser Once another list has been selected, the Channel Browser will open the last selected list.

• If all lists are turned off, pressing display the Channel Browser off, n will have no effect.

• Pressing n will bring up the Channel Browser list regardless of the last selected list in the Channel Browser

™

opens the History List by default.

3 C, # c, or n will not

™

. If Favorites List is turned

™

Favorite

™

To tune to a channel or input in Browse mode:

1 While watching TV, press 3 C or # c to open the

Channel Browser forward to the next item in the list.

In Browse mode, when you stop on an item in the Channel Browser automatically tune to the channel or input.

2 Press O to close the Channel Browser

Note: The Channel Browser™ will close automatically if you do not make a selection within 30 seconds.

™

and surf back to a previous item or

™

, it will be highlighted and the TV will

™

Chapter 5: Using the TV’s features

To tune to a channel or input in Select mode:

1 While watching TV, press 3 C or # c to open the

Channel Browser forward to the next item in the list.

In Select mode, when you stop on an item in the Channel Browser press T to tune the TV to the highlighted item.

2 Press O to close the Channel Browser

Adding and clearing channels and inputs in the History List

Adding channels and inputs to the History List:

As a channel or input is tuned, the Channel Browser™ adds it to the History List and displays it on the “right side” of the Channel Browser “shifted” to the left, eventually moving off the left side. Press 3 C to surf backward through the previously tuned channels/ inputs. Any channel or input that is tuned repeatedly will not be repeated in the History List, but instead is moved to the end of the list on the right side of the Channel Browser

The Channel Browser

• All channels that are tuned using the numeric buttons on the

remote control.

• All channels that are tuned using < or , on the remote

control for at least 5 seconds.

• All inputs that are tuned for at least 5 seconds.

Note: Whenever an item is selected that cannot be tuned (for various reasons), the TV will automatically tune to the previously viewed channel or input.

™

and surf back to a previous item or

™

, it will be highlighted but you must

™

. Previously tuned channels/inputs are

™

will store the following channels:

Tuning to the next programmed channel

To tune to the next programmed channel:

Press < or , on the remote control or TV control panel.

Note: This feature will not work unless you program channels into the TV’s channel memory (- page 26).

Tuning to a specific channel (programmed or unprogrammed)

Tuning analog channels:

Press the Channel Number buttons (0–9) on the remote control. For example, to select channel 125, press 1, 2, 5.

Tuning digital channels:

Press the Channel Number (0–9) on the remote control, followed by the dash (=) and then the sub-channel number.

Clearing channels from the History List:

• Reconfiguring the ANT 1 or ANT 2 input will clear the

History List.

Note: See page 25 for details on configuring the antenna inputs.

•

Removing the CableCARD™ will clear the History List.

• Once 32 channels or inputs are stored in the History List, the

oldest item will be removed from the list when a new channel or input is tuned.

• If History List in the Channel Browser Setup is set to

“Power Off Clear (On),” turning off the TV will clear the History List.

Chapter 5: Using the TV’s features

Switching between two channels using Channel Return

The Channel Return feature allows you to switch between two channels without entering an actual channel number each time.

1 Select the first channel you want to view. 2 Select a second channel using the Channel Number

buttons (and the dash (=) button if selecting a digital channel).

3 Press R on the remote control. The previous channel

will be tuned. Each time you press R, the TV will switch back and forth between the last two channels that were tuned.

Note: If you press R from a non-antenna input, the TV will return to the last-viewed ANT input and channel.

Switching between two channels using SurfLock

The SurfLock™ feature temporarily “memorizes” one channel in the R button, so you can return to that channel quickly from any other channel by pressing R.

To memorize a channel in the R button:

™

1 Tune the TV to the channel you want to program into the

R button.

2 Press and hold R for about 2 seconds until the message

“Channel Memorized” appears on-screen. The channel has been programmed into the R button.

3 You can then change channels repeatedly, and when you

press R, the memorized channel will be tuned.

The TV will return to the memorized channel one time only. Once you press R and then change channels again, the CH RTN memory will be cleared and the button will function as Channel Return, by switching back and forth between the last two channels that were tuned.

Chapter 5: Using the TV’s features

Selecting the picture size

You can view many program formats in a variety of picture sizes—Natural, TheaterWide 1, TheaterWide 2, TheaterWide 3, Full, 4:3 HD, and Native.

Note: The “picture size” illustrations are examples only. The format of the image (in any of the picture sizes) will vary depending on the format of the signal you are currently watching. Select the picture size that displays the current program the way that looks best to you.

You can save separate picture size preferences for each input on your TV.

To select the picture size using the remote control:

Note: If you select one of the TheaterWide

picture sizes, the top and bottom edges of the picture (including subtitles or captions) may be hidden. To view the hidden edges, either scroll the picture (TheaterWide 2 and 3 only) or try viewing the program in Full or Natural picture size.

Natural picture size

• The image is displayed close to its originally formatted

proportion. Some program formats will display with sidebars and/or bars at the top and bottom.

1 Press I on the remote control. 2 While the Picture Size screen is open, you can do one of

the following to select the desired picture size:

• Repeatedly press I.

• Press the corresponding Number button (0–6) while the

Picture Size screen is open.

• Press B or b while the Picture Size screen is open.

Picture Size

Natural

TheaterWide 1

TheaterWide 2

TheaterWide 3

Full

4:3 HD

5 6

Native

PIC SIZE

- / to Select

To select the picture size using the menus:

1 Select Picture Size in the Theater Settings menu. 2 Select the input for which you want to save your picture

settings.

3 Highlight Done and press T.

Theater Settings

Picture Size Natural

Picture Scroll

Cinema Mode Film

Auto Aspect Ratio On

Reset

Done

Natural picture size example

TheaterWide 1 picture size (for 4:3 format programs)

• The center of the picture remains close to its original

proportion, but the left and right edges are stretched wider to fill the screen.

TheaterWide 1 picture size example

TheaterWide 2 picture size (for letter box programs)

• The picture is stretched wider to fill the width of the screen,

but only slightly stretched taller.

• The top and bottom edges of the picture may be hidden. To

view the hidden areas, see “Scrolling the TheaterWide picture” on the next page.

A B C D E F G - - - - - - - - - - - - - - - -

TheaterWide 2 picture size example

Note: Full picture size may not be available for some program formats (it will be “grayed out” in the Picture Size screen).

Using these functions to change the picture size (i.e., changing the height/width ratio) for any purpose other than your private viewing may be prohibited under the Copyright Laws of the United States and other countries, and may subject you to civil and criminal liability.

Chapter 5: Using the TV’s features

TheaterWide 3 picture size (for letter box programs with subtitles)

• The picture is stretched wider to fill the width of the screen,

but only slightly stretched taller.

• The top and bottom edges are hidden. To view the hidden

areas (such as subtitles or captions), see “Scrolling the TheaterWide

A B C D E F G - - - - - - - - - - - - - - - -

picture,” at right.

A B C D E F G - - - - - - - - - - - - - - - - - - - - - - - - - -

TheaterWide 3 picture size example

Full picture size (for 16:9 [480i, 480p] source programs only)

• If receiving a squeezed 4:3 format program, the picture is

stretched wider to fill the width of the screen, but not stretched taller.

• None of the picture is hidden.

Native picture size (for 1080i and 1080p signal programs)

• If receiving a 1080i or 1080p signal program, the Native

mode displays the entire picture without scaling.

Note: Native picture size is available for 1080i and 1080p signals only. If the signal being received is other than 1080i or 1080p, “Native” will be grayed out in the Picture Size screen.

Native picture size example

Scrolling the TheaterWide® picture (TheaterWide 2 and 3 only)

You can set separate scroll settings for the TheaterWide 2 and TheaterWide 3 modes for each input.

To set the scroll settings:

Full picture size example

4:3 HD picture size (for 720p, 1080i, and 1080p program sources only)

• Sidebars fill the empty vertical spaces.

• Picture is not distorted from original size.

4:3 HD picture size example

1 Press Y and open the Video menu. 2 Highlight Theater Settings and press T.

Video

Mode Sports

Picture Settings

Noise Reduction

Color Management Pro

Game Mode

Theater Settings

Navigate

Off

Back Exit

CH RTNENTER

Select

EXIT

3 In the Picture Size field, select either TheaterWide 2

or TheaterWide 3 (you cannot scroll in any other mode).

4 Press b to highlight the Picture Scroll field. 5 Press C or c to scroll the picture up and down as needed,

from –10 to +20.

Theater Settings

Picture Size TheaterWide 2

Picture Scroll -5

Cinema Mode Film

Auto Aspect Ratio On

DoneReset

6 To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and press T.

Chapter 5: Using the TV’s features

Using the auto aspect ratio feature

When the auto aspect ratio feature is set to On, the TV will automatically select the picture size when one of the following input sources is received:

• A 480i signal from the VIDEO 1, VIDEO 2, ColorStream

HD1, or ColorStream HD2 input.

• A 1080i, 1080p, 480i, 480p, or 720p signal from the HDMI

input.

Aspect ratio of signal source

4:3 normal Natural (with sidebars) 4:3 letter box TheaterWide 2 16:9 full Full Not defined

(no ID-1 data or HDMI aspect data)

Note: The auto aspect ratio feature is not applicable to antenna or cable input sources.

To turn on the auto aspect ratio feature:

Automatic aspect size (automatically selected when Auto Aspect is On)

The current picture size you set under “Selecting the picture size” on page 36.

Selecting the cinema mode (480i and 1080i signals)

When you view a DVD (3:2 pulldown processed) from a DVD player connected to the VIDEO 1, VIDEO 2, ColorStream HD1, ColorStream HD2 (component video), or HDMI input on the TV, smoother motion can be obtained by setting the Cinema Mode to Film.

To set the Cinema Mode to Film:

1 Press Y and open the Video menu. 2 Highlight Theater Settings and press T. 3 In the Cinema Mode field, select Film.

Theater Settings

Picture Size Natural

Picture Scroll --

Cinema Mode

Auto Aspect Ratio On

4 To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and press T.

Film

DoneReset

1 Press Y and open the Video menu. 2 Highlight Theater Settings and press T. 3 In the Auto Aspect Ratio field, select On.

Theater Settings

Picture Size Natural

Picture Scroll --

Cinema Mode Film

Auto Aspect Ratio On

DoneReset

4 To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and press T.

To turn off the auto aspect ratio feature:

Select Off in step 3 above.

To set the Cinema Mode to Video:

Select Video in step 3 above.

Chapter 5: Using the TV’s features

Using the POP features

Using the POP double-window feature

The POP (picture-out-picture) double-window feature splits the screen into two windows so you can watch two programs at the same time.

To display a program in the POP window:

1 Press P to open the POP double-window.

POP double-window

TV 12

Left window Right window

(denotes active window)

2 Press C or c to highlight the desired window. When

highlighted, the window will have a green border.

3 Press + to open the Input Selection window. Select

the input source for the POP window by pressing the corresponding Number button (0–8). The current source displays in red.

POPANT1

Green border

• If you labeled all of the inputs as HIDE (- page 31), the

POP feature will be disabled and the message “Not Available” will appear if you try to open the POP doublewindow.

• The message “Not Available” will appear If you try to open the POP double-window when the Input Lock feature is in Video or Video+ mode.

To tune to the highlighted window (and close the POP double-window):

Press T after highlighting the window you want to view as a normal picture.

Notes about recording:

• If the POP window is open and you attempt to start recording, the POP window will close before recording starts.

• If you use the TV’s remote control to start recording, you will not be able to open the POP window and the message “Not Available” will appear if you try to do so.

• It is recommended that you use the TV’s remote control to start recording. If you use a device other than the TV’s remote control to start recording, you may accidentally open the POP window during the recording process. If this happens, the recorded audio will reflect the audio of the active window (left or right), which may not be the audio you intended to record.

Left window — ANT 1 and ANT 2 inputs are selectable. Right window — ColorStream HD1 and HD2 (only for 480p, 1080i, and 720p) and HDMI 1 and 2 are selectable.

Note:

• The message “Current video format cannot be displayed” will appear if you press P when the TV is in ColorStream HD1 or HD2 mode and is receiving a 480i format signal.

• The FREEZE feature is not available when the POP double-window is open. If you press B when the POP double-window is open, the message “Not available from current video mode” will appear.

Chapter 5: Using the TV’s features

Selecting the POP window audio out

While the POP double-window is open, press C or c to select which audio (left or right POP window) to be output from the TV speakers (and also from the VARIABLE AUDIO OUT and A/V AUDIO OUT terminals).

The window with the active audio is outlined with a green border.

Example: Press

Using the FREEZE feature

To use the FREEZE feature:

1 When viewing the TV, press B to make the picture a

still picture.

2 To return to the moving picture, press B again (or any

other button).

Note:

• The FREEZE feature is not available when the POP double-window is open. If you press B, the message “Not available from current video mode” will appear.

• If the TV is left in FREEZE mode for more than 15 minutes, the FREEZE mode will automatically be released and the TV will return to the moving picture.

Still pictureMoving picture

Using the FREEZE function for any purpose other than your private viewing may be prohibited under the Copyright Laws of the United States and other countries, and may subject you to civil and criminal liability.

Chapter 5: Using the TV’s features

Adjusting the picture

Selecting the picture mode

You can select your desired picture settings from different modes, as described below.

Mode Picture Quality

Sports Bright and dynamic picture (factory setting) Standard Standard picture settings (factory setting)

Movie Preference Your personal preferences

Pro 1 Custom settings based on Standard mode Pro 2 Custom settings based on Movie mode

To select the picture mode:

1 Press Y and open the Video menu. 2 Highlight Mode and press T.

3 Press B or b to select the picture mode you prefer and

press T.

Note: The picture mode you select affects the current input only. You can select a different picture mode for each input.

Lower contrast for darkened room (factory setting)

Video

Mode Sports

Picture Settings

Noise Reduction

Color Management Pro

Game Mode

Theater Settings

Navigate

Off

Select

Sports

Standard

Movie

Preference

Pro 1

Pro 2

Back Exit

CH RTNENTER

EXIT

Adjusting the picture quality

You can adjust the picture quality (Contrast, Back Light, Brightness, Color, Tint, and Sharpness) to your personal preferences.

Selection Pressing C Pressing c

Contrast lower higher Back Light darker lighter Brightness darker lighter Color paler deeper Tint reddish greenish Sharpness softer sharper

To adjust the picture quality:

1 Press Y and open the Video menu. 2 Highlight Picture Settings, and press T. 3 Press B or b to select the picture quality you want to

adjust (Contrast, Back Light, Brightness, Color, Tint, or Sharpness), and then press C and c to adjust

the setting, as described in the table above.

Picture Settings

Contrast 100

Back Light 100

Brightness

Color

Tint

Sharpness

Advanced Picture Settings

Picture Settings Mode: Preference

Contrast 70

Reset

Mode: Sports

Done

4 To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and press T.

Note:

• If you select a picture mode other than Pro 1 or Pro 2, the picture qualities you adjusted are automatically saved in the Preference mode (- “Selecting the picture mode,” at left).

• If you select picture mode Pro 1 (or Pro 2) and then change a picture quality setting, those values are saved in picture mode Pro 1 (or Pro 2).

Chapter 5: Using the TV’s features

Using the closed caption mode

The closed caption mode has two options:

• Captions—An on-screen display of the dialogue, narration,

and sound effects of TV programs and videos that are closed captioned (usually marked “CC” in program guides).

• Text—An on-screen display of information not related to

the current program, such as weather or stock data (when provided by individual stations).

To view captions or text:

1 Press Y and open the Preferences menu. 2 Highlight Closed Caption Mode and press c. 3 Press B or b to select the desired closed caption mode and

press T.

Preferences

Closed Caption Mode

Closed Caption Advanced

Input Labeling

Menu Language English

Channel Browser Setup

Navigate

• To view captions:

Highlight CC1, CC2, CC3, or CC4. (CC1 displays translation of the primary language in your area.)

Giant pandas eat leaves.

Note: If the program or video you selected is not closed captioned, no captions will display.

To view text:

•

Highlight T1, T2, T3, or T4.

Select

Off

CC1

CC2

CC3

CC4

Back Exit

CH RTNENTER

EXIT

Closed Caption Advanced

You can customize the closed caption display characteristics by changing the background color, text size, type, edge, and color.

Note:

• This feature is available for digital channels only.

• You cannot set the Caption Text and Background as the

same color.

To customize the closed captions:

1 Press Y and open the Preferences menu. 2 Highlight Closed Caption Advanced and press T.

Closed Caption Advanced

Caption Size Auto

Caption Text Type

Caption Text Edge

Caption Text Color

Background Color

Reset

Auto

Done

3 Press B or b to highlight the characteristic you want to

change, and then press C or c to select the format for that characteristic (see table below).

4 To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and press T.

Caption Size Auto, Small, Standard, Large Caption Text

Type Caption Text

Edge Caption Text

Color Background

Color

Auto, Default, Mono w. Serif, Prop. w. Serif, Mono w/o Serif, Prop. w/o Serif, Casual, Cursive, Small Capitals

Auto, None, Raised, Depressed, Uniform, Left Drop Shadow, Right Drop shadow

Auto, Black, White, Red, Green, Blue, Yellow, Magenta, Cyan

WORLD WEATHER

Temps Current F C Weather LONDON 51 11 MOSCOW PARIS ROME TOKYO

57 14 53 12 66 19 65 18

Clear Cloudy Clear Cloudy Rain

Note: If text is not available in your area, a black rectangle may appear on-screen. If this happens, set the Closed Caption Mode to Off.

To turn off the Closed Caption mode:

•

Select Off in step 3 above.

Note: A closed caption signal may not display in the following situations:

• When a videotape has been dubbed

• When the signal reception is weak

• When the signal reception is non-standard

Chapter 5: Using the TV’s features

Digital closed captions

You can use the Digital CC/Audio Selector to select digital closed caption services (if available), which will temporarily override regular closed captions on digital channels (only).

When such services are not available, the Digital CC/Audio Selector presents a default list of services. If the selected service is not available, the next available service will be used instead.

To select digital closed captions:

1 Press Y and open the Applications menu. 2 Highlight Digital CC/Audio Selector and press T.

Applications

Picture Viewer

Audio Player

Personal E-mail

Channel Browser

TV Guide On Screen

Digital CC/Audio Selector

CableCARD

Navigate

Select

Back Exit

CH RTNENTER

EXIT

3 Press B or b to select Closed Caption, and then press

C or c to select the desired service.

CC 1Closed Caption

Audio

None

4 Press O.

Adjusting the audio

Muting the sound

Press W to partially reduce (1/2 MUTE) or turn off (MUTE) the sound. Each time you press W, the mute mode will change in the following order:

Volume1/2 Mute Mute

If the closed caption mode is set to Off when you select MUTE mode, the closed caption feature is automatically activated. To mute the audio without automatically activating the closed caption feature, use Z to set the volume to 0. See “Using the closed caption mode” (- page 42) for more information on closed caption modes.

Using the digital audio selector

You can use the Digital Audio Selector to conveniently switch between audio tracks on a digital channel (for those channels that have multiple audio tracks). This temporarily overrides the audio track chosen by the language option under Audio Setup (- “Selecting stereo/SAP broadcasts” on page 44).

To use the digital audio selector:

1 Press Y and open the Applications menu. 2 Highlight Digital CC/Audio Selector and press T.

Using the Closed Caption button on the remote control

If you press ; when an analog channel is tuned:

• The CC selector will be active and will display CC1-4 and

T1-4 as the options.

• The audio selector will be disabled.

If you press ; when a digital channel is tuned:

• The CC selector will be active and will display the possible

caption options (available languages) for that channel or service. For example, in addition to English, a channel might offer closed captions in Spanish and/or French.

• The audio selector will be active and will offer different

audio choices for the digital channel (Dolby or AC3, for example).

Applications

Picture Viewer

Audio Player

Personal E-mail

Channel Browser

TV Guide On Screen

Digital CC/Audio Selector

CableCARD

Navigate

Select

Back Exit

CH RTNENTER

EXIT

3 Press B or b to select Audio, and then press C or c to

select the desired service.

CC 1Closed Caption

Audio

None

4 Press O.

Chapter 5: Using the TV’s features

Selecting stereo/SAP broadcasts

The multi-channel TV sound (MTS) feature allows you to output high-fidelity stereo sound. MTS also can transmit a second audio program (SAP) containing a second language, music, or other audio information (when provided by individual stations).

When the TV receives a stereo or SAP broadcast, the word “STEREO” or “SAP” appears when E is pressed. The MTS feature is not available when the TV is in VIDEO mode.

To listen to stereo sound:

1 Press Y and open the Audio menu. 2 Highlight Audio Setup and press T.

Audio

Audio Settings

Advanced Audio Settings

Audio Setup

3 In the MTS field, select Stereo.

Audio Setup

MTS Stereo

Language

Speakers

Optical Output Format

Dolby Digital Dynamic Range Control

Reset

English

Dolby Digital

Compressed

Done

4 To save the new settings, highlight Done and press T.

To reset the settings to the factory defaults, highlight Reset and press T.

Note:

• You can typically leave the TV in Stereo mode, because it will automatically output the type of sound being broadcast (stereo or monaural).

• If the stereo sound is noisy, select Mono to reduce the noise.

To listen to a second audio program on an analog station (if available):

Select SAP in step 3 above.

Note:

• A second audio program (SAP) can be heard only on those TV stations that offer it. For example, a station might broadcast another language as a second audio program. If you have SAP on, you will see the current program on the screen but hear the other language instead of the program’s normal audio.

• If you have SAP on and the station you are watching is not broadcasting a second audio program, the station’s normal audio will be output. However, occasionally there is no sound at all in SAP mode. If this happens, set the MTS feature to Stereo mode.

To listen to an alternate language on an ATSC digital station (if available):

Highlight the Language field in step 3 at left, and then press C or c to select the language you prefer.

Adjusting the audio quality

You can adjust the audio quality by adjusting the bass, treble, and balance.

To adjust the audio quality:

1 Press Y and open the Audio menu. 2 Highlight Audio Settings and press T. 3 Press b or B to highlight the item you want to adjust

(Bass, Treble, or Balance).

Audio Settings

Bass 100

Treble

Balance

StableSound Off

Reset

100

Done

4 Press C or c to adjust the level.

• C makes the bass or treble weaker or increases the

balance in the left channel (depending on the item selected).

• c makes the bass or treble stronger or increases the

balance in the right channel (depending on the item selected).

5 To save the new settings, highlight Done and press T.

To reset the settings to the factory defaults, highlight Reset and press T.

Using the StableSound® feature

The StableSound® feature limits the highest volume level to prevent extreme changes in volume when the signal source changes (for example, to prevent the sudden increase in volume that often happens when a TV program switches to a commercial).

To turn on the StableSound® feature:

1 Press Y and open the Audio menu. 2 Highlight Audio Settings and press T. 3 In the StableSound field, select On.

Audio Settings

Bass 100

Treble

Balance

StableSound On

Reset

100

Done

Chapter 5: Using the TV’s features

4 To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and press T.

Note: The RESET function returns your audio adjustments to the following factory settings:

Bass . . . . . . . . . center (50)

Treble. . . . . . . . center (50)

Balance . . . . . . center (0)

StableSound. . . Off

To turn off the StableSound feature:

Select Off in step 3 above.

Turning off the built-in speakers

You can use this feature to turn off the TV speakers when you connect an audio system to your TV (- “Connecting a digital audio system” and “Connecting an analog audio system” in the Installation Guide).

To turn off the built-in speakers:

1 Press Y and open the Audio menu. 2 Highlight Audio Setup and press T. 3 In the Speakers field, select Off.

Audio Setup

MTS Stereo

Language

Speakers

Optical Output Format

Dolby Digital Dynamic Range Control

Reset

English

Off

Dolby Digital

Compressed

Done

4 To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and press T.

To turn on the built-in speakers:

Select On in step 3 above.

Selecting the optical audio output format

You can use this feature to select the optical audio output format when you connect a Dolby Digital decoder or other digital audio system to the Optical Audio Out terminal on the TV (- “Connecting a digital audio system” in the Installation Guide).

3 In the Optical Output Format field, select either

Dolby Digital or PCM, depending on your device.

Audio Setup

MTS Stereo

Language

Speakers

Optical Output Format

Dolby Digital Dynamic Range Control

Reset

English

Dolby Digital

Compressed

Done

4 To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and press T.

Using the Dolby Digital Dynamic Range Control feature

This dynamic range control feature causes the ATSC dynamic range to be further compressed, allowing you to switch from ATSC to analog broadcasts at the same dynamic range.

To use the Dolby Digital Dynamic Range Control:

1 Press Y and open the Audio menu. 2 Highlight Audio Setup and press T. 3 In the Dolby Digital Dynamic Range Control field,

select Compressed. When Standard is selected, the audio is output with minimal compression.

Audio Setup

MTS Stereo

Language

Speakers

Optical Output Format

Dolby Digital Dynamic Range Control

Reset

English

Off

Dolby Digital

Compressed

Done

4 To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and press T.

Note:

• This item will be grayed out for NTSC signals, Video, ColorStream, and PC inputs.

• The Dolby Digital Dynamic Range Control will function in relation to Optical Output Format.

To select the optical audio output format:

1 Press Y and open the Audio menu. 2 Highlight Audio Setup and press T.

Using the Locks menu

Chapter 5: Using the TV’s features

When the correct PIN code is entered, the Locks menu opens.

The Locks menu includes the Enable Rating Blocking, Edit Rating Limits, Channels Block, Input Lock, Front (control) Panel Lock, and New PIN Code features. You can use these features after entering the correct PIN code.

Entering the PIN code

Press Y and highlight the Locks menu icon.

Locks

Enable Rating Blocking

Edit Rating Limits

Channels Block

Input Lock

Game Timer

New PIN Code

Navigate

ENTER

Select

Off

OffFront Panel Lock

CH RTN

Back Exit

EXIT

2 Press b, which displays the PIN code entry screen.

• The Lock System screen (below) appears if a PIN

code has not been stored. Press the Channel Number buttons to enter a new four-digit code, enter the code a second time to confirm, and press T.

Lock System

Please enter a 4 digit PIN code

Confirm PIN code

Cancel Done

• The Locks/Active screen (below) appears if the PIN

code is already stored. Use the Number buttons to enter your four-digit code and press T.

Locks Active

Please enter the 4 digit PIN code

****

Cancel

Done

Locks

Enable Rating Blocking

Edit Rating Limits

Channels Block

Input Lock

Game Timer

New PIN Code

Navigate

ENTER

Off

Select

Off

OffFront Panel Lock

Back

MENU EXIT

Exit

If you cannot remember your PIN code

While the PIN code entering screen is displayed, press E four times within five seconds. The PIN code will be cleared and you can enter a new PIN code.

Changing your PIN code

Press Y and highlight the Locks menu icon.

2 Press b to display the PIN code entering screen. 3 Enter your four-digit PIN code and press T. 4 Press b to highlight New PIN Code and press T.

Locks

Enable Rating Blocking

Edit Rating Limits

Channels Block

Input Lock

Game Timer

New PIN Code

Navigate

ENTER

Off

Select

Off

OffFront Panel Lock

Back

MENU EXIT

Exit

5 Press the Number buttons to enter a new four-digit code.

Reenter the PIN code to confirm it.

6 Press T. The new PIN code is now active.

New PIN Code

Please enter a 4 digit PIN code

****

Confirm PIN code

****

If the wrong PIN code is entered, the message “Incorrect PIN code, please try again!” appears. Highlight Retry and press T. Enter the code again and press T.

Cancel Done

Chapter 5: Using the TV’s features

Blocking TV programs and movies by rating (V-Chip)

Some TV programs and movies include signals that classify the content of the program (violence, sex, dialog, language). The V-Chip feature in this TV detects the signals and blocks the programs according to the ratings you select. (For rating descriptions, see the tables on the next page.)

Note: Rating blocking is a function of the V-Chip feature in this TV, which supports the U.S. V-Chip system only.

To block and unblock TV programs and movies:

1 Press Y and highlight the Locks menu icon. 2 Press b to display the PIN code entering screen. 3 Enter your four-digit PIN code and press T. 4 Press b to highlight Enable Rating Blocking. 5 Press c and b to select On, and press T.

6 Press b to highlight Edit Rating Limits and press T.

The Edit Rating Limits screen (below) appears.

7 Press BbC c and then press T to select the level of

blocking you prefer. A box with an “5” is a rating that will be blocked. As you highlight a rating, a definition for the rating appears at the bottom of the screen.

8 When you are finished selecting the ratings you want to

block, highlight Done and press T.

Downloading an additional rating system for blocking TV programs and movies

In the future, an additional rating system may become available for use in selectively blocking programs.

Note: The currently tuned station must be receiving a digital signal before an additional rating system can be downloaded.

To download the additional rating system (if available):

The Edit Rating Limits screen appears.

7 Highlight Alt RS and press T. The Edit Alternate

Ratings screen will appear.

Note:

• The Alt RS button will only be available if an additional rating system is currently available.

• It may take several minutes for the TV to download the additional rating system.

• The information displayed in the Alternate Ratings screen will depend on the configuration of the additional rating system available at the time of download.

8 Press B b C c and then press T to select the level of

blocking you prefer. A box with an “5” is a rating that will be blocked.

9 When you are finished selecting the ratings you want to

block, highlight Done and press T.

10 In the Edit Rating Limits screen, highlight Done and

press T.

Note:

• The additional rating system can only be downloaded one time. You will not be able to download any updates to the rating system should such updates become available.

• The additional rating system is not designed, transmitted, or controlled by the TV or Toshiba, nor is the availability of an additional rating system determined or controlled by Toshiba. Similarly, the rating of programs in an additional rating system is not determined, transmitted, or controlled by the TV or Toshiba.

• The additional rating system is an evolving technology; therefore, availability, content, and format may vary.

Chapter 5: Using the TV’s features

Independent rating system for broadcasters Ratings Description and Content themes

Mature Audience Only (This program is specifically designed to be viewed by adults and therefore may

TV-MA

TV-14

be unsuitable for children under 17.) L) Crude or indecent language S) Explicit sexual activity V) Graphic violence

Parents Strongly Cautioned (This program contains some material that many parents would find unsuitable for children under 14 years of age.)

Intensely suggestive dialog L) Strong, coarse

language

S) Intense sexual situations V) Intense

violence

Parental Guidance Suggested (This program contains material parents may find unsuitable for

TV-PG

younger children.)

Some suggestive dialog L) Infrequent coarse

language

S) Some sexual situations V) Moderate

violence

TV-G

TV-Y7, TV-Y7FV

TV-Y

General Audience (Most parents would find this program suitable for all ages.)

Directed to Older Children (This program is designed for children age 7 and above. Note: Programs in which fantasy violence may be more intense or more combative than other programs in this category are designated TV-Y7FV.)

All Children (This program is designed to be appropriate for all children.)

Independent rating system for movies Ratings Description and Content themes

X NC-17

PG-13

Note:

• If you place an “5” in the box next to “‘None’ Rated,”

programs rated “None” will be blocked; however, programs that do not provide any rating information will not be blocked.

• To display the rating of the program you are watching, press E on the remote control. If it is rated “None,” the word “NONE” appears in the RECALL screen (as shown below right). If rating information is not provided, no rating will appear in the RECALL screen.

X-rated (For adults only)

Not intended for anyone 17 and under

Restricted (Under 17 requires accompanying parent or adult)

Parents Strongly Cautioned (Some material may be inappropriate for children under 13)

Parental Guidance Suggested (Some material may not be suitable for children)

General Audience (Appropriate for all ages)

TV PG L V– NONE

Blocking channels

With the Channels Block feature, you can block specific channels. You will not be able to tune blocked channels unless you unblock them.

To block channels:

1 Press Y and highlight the Locks menu icon. 2 Press b to display the PIN code entering screen. 3 Enter your four-digit PIN code and press T (- page 46). 4 Press b to highlight Channels Block and then press T.

Locks

Enable Rating Blocking

Edit Rating Limits

Channels Block

Input Lock

Game Timer

New PIN Code

Navigate

ENTER

Off

Select

Off

OffFront Panel Lock

Back

MENU EXIT

Exit

5 Press BbC c to select the input for which you want to

block channels (ANT1 or ANT2) and press T. A list of the channels available for that input will be

displayed along with the call letters for each channel, if available.

6 Press Bb to highlight the channel you want to block and

press T, which puts an “5” in the box next to that channel.

Channels Block

ANT 1

ANT 2

Allow All

Block All

Cancel

Done

7 Repeat step 6 for other channels you want to block. 8 Highlight Done and press T.

To unblock individual channels:

In step 6 above, press Bb to highlight the channel you want to unblock, press T to remove the “5” from the box, highlight Done and press T.

To block all channels at once:

Highlight Block All in step 6 above, and then highlight Done and press T.

Chapter 5: Using the TV’s features

To unblock all blocked channels at once:

Highlight Allow All in step 6 on the previous page, and then highlight Done and press T.

Channels Block

ANT 1

ANT 2

Allow All

Block All

Cancel

Done

Unlocking programs temporarily

If you try to tune the TV to a program that exceeds the rating limits you set, the TV will enter program lock mode and the following message will appear:

This program exceeds the rating limit you set.

Push 'mute' to enter PIN.

You can either temporarily unlock the program or select an unlocked program to watch.

To temporarily unlock the program:

1 Press W. 2 Enter your four-digit PIN code and press T. If the correct

code is entered, the program lock mode is released and the normal picture appears. All locking is disabled until the TV is turned off, and will be enabled when the TV is turned on again.

Locks Active

Enter PIN code to temporarily un-block.

Using the input lock feature

You can use the Input Lock feature to lock the video inputs (VIDEO 1, VIDEO 2, ColorStream HD1, ColorStream HD2, HDMI 1, HDMI 2, and PC) and channels 3 and 4. You will not be able to view the input sources or channels until you unlock the inputs.

To lock/unlock the video inputs:

1 Press Y and highlight the Locks menu icon. 2 Press b to display the PIN code entering screen. 3 Enter your four-digit PIN code and press T. 4 Press b to highlight Input Lock and press c.

Locks

Enable Rating Blocking

Edit Rating Limits

Channels Block

Input Lock

Game Timer

New PIN Code

Navigate

ENTER

Off

Select

Off

Video

Video +

OffFront Panel Lock

Back

MENU EXIT

Exit

5 Press B or b to select the desired level of video input

locking (Video, Video+, or Off, as described below), and then press T.

Video: Locks VIDEO 1, VIDEO 2, ColorStream HD1/ HD2, HDMI 1/HDMI 2, and PC.

Video+: Locks VIDEO 1, VIDEO 2, ColorStream HD1/ HD2, HDMI 1/HDMI 2, PC and channels 3 and 4.

• Select Video+ if you play video tapes via an ANT input.

• When a CableCARD

channels 3 and 4.

Off: Unlocks all video inputs and channels 3 and 4.

™

is inserted, Video+ will not lock

Cancel

****

Done

Chapter 5: Using the TV’s features

Using the GameTimer

™

You can use the GameTimer to set a time limit for playing a video game (30–120 minutes). When the GameTimer is activated, the TV enters Input Lock mode and locks out the input source for the video game device.

To set the GameTimer™:

1 Press Y and highlight the Locks menu icon. 2 Press b to display the PIN code entering screen. 3 Enter your four-digit PIN code and press T. 4 Press b to highlight Game Timer and press c. 5 Press B or b to select the length of time until the Input

Lock is activated (30, 60, 90, or 120 minutes) and press T.

Locks

Enable Rating Blocking

Edit Rating Limits

Channels Block

Input Lock

Game Timer

New PIN Code

Navigate

To cancel the GameTimer™:

Select Off in step 5 above.

To deactivate the Input Lock once the GameTimer has activated it:

Set the Input Lock to Off (- “Using the input lock feature” on the previous page).

Note:

• A message will appear when 10 minutes, 3 minutes, and 1 minute remain on the GameTimer.

• If the TV loses power with time remaining on the GameTimer, when power is restored the TV will enter Input Lock mode (as if the GameTimer had been activated) and you will have to deactivate the Input Lock (as described above).

ENTER

Off

Select

Off

OffFront Panel Lock

Back

MENU EXIT

Off

30 min

60 min

90 min

120 min

Exit

Using the control panel lock feature

You can lock the control panel to prevent your settings from being changed accidentally (by children, for example). When the control panel lock is On, none of the controls on the TV control panel will operate except POWER.

To lock the control panel:

1 Press Y and highlight the Locks menu icon. 2 Press b to display the PIN code entering screen. 3 Enter your four-digit PIN code and press T. 4 Press b to highlight Front Panel Lock. 5 Press c, and then B or b to highlight On and press T.

When the control panel is locked and any button on the control panel (except POWER) is pressed, the message “Not Available” appears.

Locks

Enable Rating Blocking

Edit Rating Limits

Channels Block

Input Lock

Game Timer

New PIN Code

Navigate

ENTER

Select

To unlock the control panel:

Highlight Off in step 5 above, or press and hold the VOLUME – button on the TV control panel for about 10

seconds until the volume icon appears.

Off

OffFront Panel Lock

Off

MENU EXIT

Back

Off

Exit

Chapter 5: Using the TV’s features

Setting the sleep timer

You can set the sleep timer to turn off the TV after a set length of time (maximum of 180 minutes).

To set the sleep timer using the remote control:

Press [ on the remote control to set the length of time until the TV turns off. Repeatedly press [ to increase the time in 10-minute increments, or press B or b to increase or decrease the time in 10-minute increments, to a maximum of 180 minutes.

To set the sleep timer using the menus:

1 Press Y and open the Setup menu. 2 Highlight Sleep Timer and press T.

Setup

Installation

Sleep Timer

On/Off Timer

PC Settings

PC Audio HDMI 1 Audio

Slide Show Interval

Navigate

3 Press the Number buttons to enter the length of time

in 10-minute increments.

Sleep Timer

Enter total minutes until the TV

turns off automatically (Maximum

Cancel Done

4 Highlight Done and press T.

Note:

• When a power failure occurs, the sleep timer setting may be cleared.

• A message will display when there is one minute remaining on the sleep timer.

To display the remaining sleep time:

Press [.

Sleep Timer

Auto

2 Sec

CH RTNENTER

Select

180 minutes)

120

120 Minutes

Back Exit

EXIT

Setting the On/Off Timer

You can set the On/Off Timer to turn the TV on and off automatically at a preset time on a recurring basis.

Note: You must first set the time (- page 28).

To set the On/Off Timer:

1 Press Y and open the Setup menu. 2 Highlight On/Off Timer and press T. 3 In the DAY field, press C or c to select the recurrence

(weekends, weekdays, every day, etc).

On/Off Timer

Turn TV ON:

Day

Time (HH:MM)

TV ON Duration:

Reset DoneCancel

4 Press b to highlight the Time field, and then use the

Number buttons to enter the time you want the TV to turn on automatically.

5 When the AM/PM field is highlighted, press c to select

AM or PM.

6 Press b to highlight the TV ON Duration field, and then

press C or c to select the length of time until the TV turns off (30 Minutes, 1Hour, 2 Hours, 4Hours,

8 Hours, or 12 Hours).

7 Highlight Done and press T. 8 Turn off the TV. The TV will turn on automatically on the

day(s) and at the time you set. The TV will then turn off automatically after the length of time you set in the TV ON Duration field.

Note:

• When a power failure occurs, the On/Off Timer settings may be cleared.

• To display the On/Off Timer setting, press E.

To turn off the On/Off Timer:

Select Not Set in step 3 above.

On/Off Timer

Turn TV ON:

Day

Weekends

09 00 AM

30 Minutes

Not Set

Note: You also can view the remaining sleep time by pressing

To cancel the sleep timer:

Repeatedly press [ until it is set to 0 minutes.

Reset DoneCancel

Chapter 5: Using the TV’s features

Using the PC settings feature

You can view the image from a PC on the TV screen. The PC must be connected to the TV’s PC IN terminals (- Installation Guide).

The PC Settings feature allows you to make any necessary adjustments to the image.

If the edges of the image are not visible, you can adjust the

Horizontal Position/Width and Vertical Position/ Height.

If the picture is affected by interference, you can adjust the Clock Phase and Sampling Clock.

To adjust the PC settings:

1 Repeatedly press + to select PC input mode

(- “Selecting the video input source to view” page 31).

2 Press Y and open the Setup menu. 3 Highlight PC Settings and press T.

Note: If a PC is not connected, this feature will be grayed out in the Setup menu.

Horizontal Position:

•

Moves the picture left/right. The adjustment range is within ±5 from center.*

• Vertical Position:

Moves the picture up/down. The adjustment range is within ±5 from center.*

• Horizontal Width:

Adjusts the width of the picture. The adjustment range is within ±5 from center.*

• Vertical Height:

Adjusts the height of the picture. The adjustment range is within ±5 from center.*

• Clock Phase:

Helps to reduce noise and sharpen the picture. The adjustment range is within ±2 from center.*

• Sampling Clock:

Helps to reduce noise and minimize periodic vertical stripes on the screen. The adjustment range is within ±15 from center.*

* The range of adjustment may vary slightly.

Setting the PC Audio mode

Setup

Installation

Sleep Timer

On/Off Timer

PC Settings

PC Audio HDMI 1 Audio

Slide Show Interval

Navigate

Select

Auto

2 Sec

CH RTNENTER

Back Exit

EXIT

4 Press B or b to highlight the item you want to adjust. 5 Press C or c to make the appropriate adjustments.

PC Settings

Horizontal Position 0

Horizontal Width 0

Vertical Position

Vertical Height

Clock Phase

Sampling Clock

Note: The screen is disrupted momentarily when adjusting the PC settings. This is not a sign of malfunction.

Reset

Done

This function allows you to output the sound from your PC (if connected) or mute the sound from your PC and output the sound from your HDMI (DVI) connection. (- Installation Guide)

To set the PC Audio:

1 Press Y and open the Setup menu. 2 Highlight PC Audio. 3 Press c and then press b to select No or Yes.

Yes: Outputs the sound from your PC. No: Mutes the sound from your PC, and outputs the

sound from the HDMI connection.

Setup

Installation

Sleep Timer

On/Off Timer

PC Settings

PC Audio

HDMI 1 Audio

Slide Show Interval

Navigate

Select

Auto

2 Sec

CH RTNENTER

Yes

Back Exit

EXIT

™

audio

Chapter 5: Using the TV’s features

Displaying TV status information using RECALL

To display TV status information:

Press E on the remote control. The following information will display (if applicable):

• Current input (ANT 1, ANT 2, VIDEO 1, etc.)

• If ANT 1 or ANT 2 is the current input, either “CABLE”

(for cable TV) or “TV” (for over-the-air broadcasts).

• Channel number (if in ANT 1 or ANT 2 mode)

• Digital signal strength indicator (bar graph in lower right

corner of screen; for ATSC signal only)

• Time (if set)

• On timer setting (if set)

• Remaining time on game timer (if set)

• Remaining time on sleep timer (if set)

• Stereo or SAP audio status

• V-Chip rating status

• Picture size

• Video resolution

STEREO

NC-17 Sleep Timer: 18 min. Game Timer: 28 min.

Natural 480i

5:32 pm

CABLE

81-1

ANT 1

Understanding the auto power off feature

The TV will automatically turn itself off after approximately 15 minutes if it is tuned to a vacant channel or a station that completes its broadcast for the day. This feature functions in ANT 1 and ANT 2 modes only.

Understanding the last mode memory feature

If the power is cut off while you are viewing the TV, the Last Mode Memory feature automatically turns on the TV when the power is resupplied.

Note: You should unplug the TV’s power cord if it is possible that you will be away from the TV for an extended period of time after the power is restored. This will prevent the TV from turning on automatically in your absence.

Sample RECALL screen

To close the RECALL screen:

Press E again.

Chapter 6: Using the TV’s advanced features

Using the advanced picture settings features

Using dynamic contrast

When dynamic contrast is set to Low, Middle, or High, the TV will detect changes in the picture quality that affect the appearance of your contrast settings and then automatically adjust the video.

To select dynamic contrast preferences:

1 Press Y and open the Video menu. 2 Highlight Picture Settings and press T.

Video

Mode Sports

Picture Settings

Noise Reduction

Color Management Pro

Game Mode

Theater Settings

3 Highlight Advanced Picture Settings and press T.

Picture Settings

Contrast 100

Back Light 100

Brightness

Color

Tint

Sharpness

Advanced Picture Settings

4 In the Dynamic Contrast field, select either Off, Low,

Middle or High.

Advanced Picture Settings Mode: Preference

Dynamic Contrast

Static Gamma

Color Temperature

Vertical Edge Enhancer

5 To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and press T.

Note: If you select one of the factory-set picture modes (Sports, Standard, or Movie) and then change the dynamic contrast setting, the picture mode automatically changes to Preference.

Navigate

Reset

Off

Back Exit

CH RTNENTER

Done

Cool

High

EXIT

Mode: Sports

Off

Select

Using the static gamma feature

The static gamma feature allows you to adjust the levels of black in the picture.

To adjust the static gamma settings:

1 Press Y and open the Video menu. 2 Highlight Picture Settings and press T.

Video

Mode Sports

Picture Settings

Noise Reduction

Color Management Pro

Game Mode

Theater Settings

Navigate

Off

Back Exit

CH RTNENTER

Select

EXIT

3 Highlight Advanced Picture Settings and press T.

Picture Settings

Contrast 100

Back Light 100

Brightness

Color

Tint

Sharpness

Advanced Picture Settings

Reset

Mode: Sports

Done

4 In the Static Gamma field, press C or c to adjust the

static gamma. The adjustment range is within ±5 from center.

Advanced Picture Settings Mode: Preference

Dynamic Contrast

Static Gamma

Color Temperature

Vertical Edge Enhancer

Reset

High

Cool

High

Done

• If the setting is moved in the minus direction, the detail

of black colors will be decreased.

• If the setting is moved in the plus direction, the detail of

black colors will be increased.

5 To save the new settings, highlight Done and press T.

To revert the factory defaults, highlight Reset and press T.

Note: If you select one of the factory-set picture modes (Sports, Standard or Movie) and then change the static gamma setting, the picture mode automatically changes to Preference.

Chapter 6: Using the TV’s advanced features

Selecting the color temperature

You can change the quality of the picture by selecting from three preset color temperatures (cool, medium, and warm), as described below.

To select the color temperature:

1 Press Y and open the Video menu. 2 Highlight Picture Settings and press T. 3 Highlight Advanced Picture Settings and press T. 4 Highlight Color Temperature and press T.

5 In the Color Temperature field, select the mode you

prefer (Cool, Medium, or Warm).

Using the Vertical Edge Enhancer feature

The Vertical Edge Enhancer feature strengthens video contour.

To turn on the Vertical Edge Enhancer feature:

1 Press Y and open the Video menu. 2 Highlight Picture Settings

6 Press B or b to select either B Drive or G Drive, and

then press C or c to adjust the settings.

• B Drive: c makes the picture blueish.

• G Drive: c makes the picture greenish.

Note: The B Drive and G Drive settings are connected to the Color Temperature settings and will change based on which setting is selected in step 5 above.

7 To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and press T.

Note: If you select one of the factory-set picture modes (Sports, Standard, or Movie) and then change the color temperature mode, the picture mode automatically changes to Preference.

Chapter 6: Using the TV’s advanced features

Using CableClear® digital noise reduction

The CableClear® digital noise reduction feature allows you to reduce visible interference in your TV picture. This may be useful when receiving a broadcast with a weak signal (especially a Cable channel) or playing a noisy video cassette or disc.

To change the CableClear settings:

1 Press Y and open the Video menu. 2 Highlight Noise Reduction and press T.

Video

Mode Preference

Picture Settings

Noise Reduction

Color Management Pro

Game Mode

Theater Settings

Navigate

Off

Back Exit

CH RTNENTER

Select

EXIT

3 In the CableClear field, select your desired setting.

Noise Reduction ANT 1

CableClear

MPEG Noise Reduction

Reset

Done

Auto

Low

Using MPEG noise reduction

The MPEG noise reduction feature allows you to reduce visible interference caused by MPEG compression. Choices for MPEG noise reduction are Off, Low, Middle, and High. Off is automatically selected when this feature is disabled (“grayed out”).

To select the MPEG noise reduction level:

1 Press Y and open the Video menu. 2 Highlight Noise Reduction and press T. 3 Press B or b to highlight the MPEG Noise Reduction

field, and then press C or c to select either Off, Low, Middle or High.

Noise Reduction ANT 1

CableClear

MPEG Noise Reduction

Reset

Done

Auto

Low

4 To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and press T.

Note:

• If the current input is ANT 1, ANT 2, VIDEO 1, or VIDEO 2, the menu will display the text “CableClear.”

The available selections are Off, Auto, Low, Middle, and High.

• If the current input is ColorStream HD1, ColorStream HD2, or HDMI, the menu will display the text “DNR.” The available selections are Off, Auto, Low, Middle, and High. Auto will react proportionally to the strength of

the noise. Low, Middle, and High will reduce the noise in varying degrees, from lowest to highest, respectively.

4 To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and press T.

Chapter 6: Using the TV’s advanced features

Using the Color Management Pro feature

The new Color Management Pro feature allows you to adjust standard colors as well as create 3 custom user colors. The menu will consist of 3 items: Color management, color palette adjustment, and reset.

To turn on Color Management Pro:

1 Press Y and open the Video menu. 2 Highlight Color Management Pro and press T.

Video

Mode Preference

Picture Settings

Noise Reduction

Color Management Pro

Game Mode

Theater Settings

Navigate

Off

Back Exit

CH RTNENTER

Select

EXIT

3 In the Color Management field, select On.

Color Management Pro ANT 1

Color Management

Color Palette Adjustment

Reset

Note: If you select one of the factory-set picture modes (Sports, Standard, or Movie) and then change the Color Management setting, the picture mode automatically changes to Preference.

To turn off Color Management Pro:

Select Off in Step 3 above.

Using the Color Palette Adjustment

When the color palette adjustment is selected, the list of base colors and user colors will be displayed. You can select a base color to adjust or choose to create a user color.

Note: To use Color Palette Adjustment, Color Management must be set to On.

To adjust the Base Colors:

1 From the Color Management Pro menu, highlight

Color Palette Adjustment and press T.

Color Management Pro ANT 1

Color Management

Color Palette Adjustment

Reset

2 The Select Standard Color window will be displayed.

Press B or b to highlight the color you want to adjust, and then press T.

Select Standard Color

Base Colors

Red

Green

Blue

Yellow

Magenta

Cyan

User Colors

User 1

User 2

User 3

3 The Color Adjustment window will be displayed.

Press B to freeze the picture. To return to moving picture, press B again.

Color Adjustment

Hue 0

Saturation 0

Brightness 0

Red

Standard Color

After Adjustment

4 Press B or b to select either Hue, Saturation, or

Brightness, and then press C and c to adjust the setting.

Note: Press f to reset Hue, Saturation, and Brightness to the factory settings for the selected color.

5 Press R to return to the previous menu. 6 Repeat steps 2 through 5 to adjust any other color.

To adjust the User Colors:

1 From the Color Management Pro menu, highlight

Color Palette Adjustment, and then press T.

2 The Select Standard Color window will be displayed.

Press B or b to highlight either User 1, User 2, or User 3 mode, and then press T.

Select Standard Color

Base Colors

Red

Green

Blue

Yellow

Magenta

Cyan

User Colors

User 1

User 2

User 3

(continued)

Chapter 6: Using the TV’s advanced features

3 The Color Adjustment window will be displayed.

Press B or b to highlight Change Standard Color, and then press T.

Color Adjustment

Hue --

Saturation --

Brightness --

User 1

Standard Color

After Adjustment

Change Standard Color

The video on- screen will automatically freeze and the cross hairs will appear on the video.

Note: Release the video anytime by pressing B.

Navigate

Select

CH RTNENTER

Back

FREEZE

Freeze/Unfreeze Exit

EXIT

4 Press BbC c to move the cross hairs to the color you

want to adjust, and then press T.

To reset Color Management Pro to its factory settings:

1 From the Color Management Pro menu, highlight

Reset, and then press T.

Color Management Pro ANT 1

Color Management

Color Palette Adjustment

Reset

2 A confirmation message will appear. Highlight OK, and

then press T.

Are you sure?

OKCancel

3 Press O.

Using the Game Mode feature

You can use the Game Mode feature for shorter frame delays when playing a video game requiring split-second timing between the on-screen display and input from the controller (such as music creation and high-action games).

Note: To use the Game Mode feature, the current video input must be Video 1, Video 2, ColorStream HD1, ColorStream HD2, HDMI 1 or HDMI 2. The Game Mode cannot be turned on when any other video input is selected.

Navigate

Select

CH RTNENTER

Back

FREEZE

Freeze/Unfreeze Exit

EXIT

5 Press B or b to select either Hue, Saturation, or

Brightness, and then press C or c to adjust the setting.

Color Adjustment

Hue 0

Saturation +30

Brightness +11

Note: You can reset the Hue, Saturation, and Brightness colors to "0" for any user color by

pressing f.

User 1

Standard Color

After Adjustment

Change Standard Color

6 Repeat step 5 for other items. 7 Press O.

To turn on Game Mode:

1 Press Y and open the Video menu. 2 Press B or b to highlight the Game Mode field, and then

press C or c to select On.

Video

Mode Preference

Picture Settings

Noise Reduction

Color Management Pro

Game Mode

Theater Settings

Navigate

To turn off Game Mode:

Select Off in step 2 above, change the video input, or turn the TV off and then on again.

Note: You can change the video input in any of the following ways:

• Pressing + on the remote control (- page 31).

• Changing the channel using the Numbers or < / ,, R,

3C, #c.

Off

Back Exit

CH RTNENTER

Select

EXIT

Chapter 6: Using the TV’s advanced features

Using the advanced audio settings features

Using the SRS WOW™ surround sound feature

SRS WOW™ is a special combination of SRS Labs audio technologies (SRS 3D, SRS Focus, and SRS TruBass) that creates a thrilling surround sound experience with deep, rich bass from stereo sound sources. Your TV’s audio will sound fuller, richer, and wider.

To adjust the WOW™ settings:

1 Put the TV in STEREO mode (- “Selecting stereo/SAP

broadcasts” on page 44).

2 Press Y and open the Audio menu. 3 Highlight Advanced Audio Settings and press T. 4 Press b or B to highlight the WOW feature you want to

adjust, and then press C or c to adjust the item.

Advanced Audio Settings

WOW: SRS 3D

WOW: SRS Focus

WOW: SRS TruBass High

Dolby Virtual SRS TruSurround

Reset

• WOW: SRS 3D — To turn the surround sound effect

On or Off.

Note: If the broadcast is monaural, the SRS 3D effect will not work.

WOW: SRS Focus — To turn the vocal emphasis effect

•

On or Off.

• WOW: SRS TruBass — To select the desired bass

expansion level (Off, Low, or High).

5 To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and press T.

Done

Off

Using the virtual surround sound feature (Dolby

The Dolby Virtual/SRS TruSurround feature allows you to enjoy virtual surround sound from the TV’s speakers.

To turn on the Dolby Virtual/SRS TruSurround feature:

Virtual/SRS TruSurround™)

1 Press Y and open the Audio menu. 2 Highlight Advanced Audio Settings and press T. 3 In the Dolby Virtual/SRS TruSurround field, select

On.

Advanced Audio Settings

WOW: SRS 3D

WOW: SRS Focus

WOW: SRS TruBass High

Dolby Virtual SRS TruSurround

Reset

Done

Off

4 To save the new settings, highlight Done and press T.

To revert to the factory defaults, highlight Reset and press T.

To turn off the Dolby Virtual/SRS TruSurround feature:

Select Off in step 3 above.

Note: The Dolby Virtual/SRS TruSurround and WOW SRS 3D features cannot be on at the same time. If you set one to On, the other will automatically be set to Off.

WOW, TruSurround, SRS and l symbol are trademarks of SRS Labs, Inc. WOW and TruSurround technologies are incorporated under license from SRS Labs, Inc.

Chapter 7: Using the THINC™ home network feature

The Toshiba Home Interactive Network Connection (THINC

™

) feature allows you to connect the TV to your home network, which will enable access to file sharing, personal e-mail, and e-mail scheduling features.

File sharing

You can access JPEG and MP3 files that are stored on your networked home PC and view/play them on the TV.

Note: Requires a home network* (- Installation Guide).

Does NOT require Internet/e-mail service.

Personal E-mail

The Personal E-mail feature allows you to access your e-mail server through the TV. You can create, view, reply to, and forward personal e-mails and JPEG format picture attachments.

E-mail scheduling of recordings and reminders

You can schedule recordings and reminders by sending an e-mail to the TV from any PC.

Note:

• Requires a compatible recording device (- Installation

Guide); a home network* (- Installation Guide); and

home Internet service with a dedicated POP3 e-mail address for the TV (different from your personal e-mail address).

• Contact your Internet Service Provider (ISP) to obtain and set up Internet/e-mail service.

• You will NOT be able to access or browse the Internet through the TV.

Follow the steps in sections A through D (- pages 60–66) to set up and use the TV’s home network features.

* The THINC

Microsoft versions of Microsoft Service Pack 2.

Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.

™

home network feature is compatible only with

Windows® 2000 and the Home and Professional

Windows® XP Service Pack 1 and

A. Connecting the TV to your home network

1 Connect the TV to your home network via the TV’s

RJ-45 (Ethernet) port. See the Installation Guide for connection instructions.

2 If you want to use file sharing only and do not have

Internet service in your home: Go to section B, “Setting up the network address,” on the

next page.

Note: If you do not have Internet service, you will not be able to use the personal e-mail and e-mail scheduling features.

If you want to use file sharing, personal e-mail, and e-mail scheduling:

a) You must have Internet service in your home and a

dedicated e-mail address for the TV (different from your personal e-mail address). Contact your ISP to obtain and set up Internet/e-mail service in your home.

b) After you have obtained Internet/e-mail service in your

home (from your ISP), go to section B, “Setting up the network address” on the next page.

For home network troubleshooting tips, see Chapter 8.

The unauthorized recording, use, distribution, or revision of television programs, videotapes, DVDs, and other materials is prohibited under the Copyright Laws of the United States and other countries, and may subject you to civil and criminal liability.

Chapter 7: Using the THINC™ home network feature

B. Setting up the network address

To set up the network address:

1 First, try automatically setting up the network address

(below).

2 If the automatic setup is not successful, you can either

retry the automatic setup (below) or try manually setting up the network address (- page 62).

Note:

• If you used an Ethernet crossover cable to connect your PC directly to the TV, you will not be able to use the automatic setup, and must manually set up the network address.

• If you used a hub or switch to connect the TV to your home network, you will not be able to use the automatic setup, and must manually set up the network address.

• If you used a router with built-in DHCP functionality, use the automatic setup. Manual setup may not work.

Router technology, like all new and emerging technology, may from time to time cause compatibility issues because of the differences in router systems implemented by the various router manufacturers; however, most issues can be easily resolved. If you think your Toshiba TV and router might have compatibility problems, please contact the following:

•

In the U.S. 3811 contact.asp

• In Canada, call TCL Customer Service at

1-800-268-3404 or visit http://www.toshiba.ca.

, call TACP Consumer Solutions at

or visit

http://www.tacp.com/customersupport/

1-800-631-

5 The message “Obtain network address automatically?”

will display. Highlight Yes and press T.

Basic Network Setup

Obtain network address automatically?

Yes No

6 The message “Please wait…” will display while the TV is

attempting to load the network address information from the DHCP server.

Basic Network Setup

Please wait...

If the automatic network address setup is successful,

go to step 7.

If the automatic network address setup is not

successful, go to step 8.

7 If the automatic network address setup is successful, the

following screen will appear:

Basic Network Setup

Done! Network address information has been found!

Exit

a) Press T to close the screen and return to the Network

menu.

b)Skip to section C, “Setting up file sharing on your PC”

(- page 63).

8 If the automatic network address setup is not successful,

the following screen will appear:

Automatically setting up the network address

Press Y and open the Setup menu.

2 Highlight Installation and press T. The Installation

menu appears.

3 Open the Network menu. 4 Highlight Basic Network Setup and press T.

Network

Basic Network Setup

Personal E-mail Setup

E-mail Scheduling Setup

Home File Server Setup

Software Upgrade

Navigate

Select

Back Exit

CH RTNENTER

EXIT

a) Make sure all cables for your home network are

securely connected.

b)Make sure your home network is set up properly. See

the Installation Guide for TV connection information. Also consult the owner’s manuals for your other components.

c) Make sure the DHCP and security settings on your

home router are correct. Consult the owner’s manual

for your router.

d) Retry the automatic network address setup by following

these steps: (1) Highlight OK and press T.

(2)Repeat steps 1–6. (If you have already repeated

this setup process, go to step 9.)

(continued)

Chapter 7: Using the THINC™ home network feature

9 If, after repeating steps 1–6, you receive the error

message shown in step 8:

Either… a) Highlight “OK” and press T. b)Go to “Manually setting up the network address.” Or… a) Highlight “OK” and press T. b)Continue to sections C, D, and E (- pages 63–67)

(to set up and use file sharing) and/or to sections F, G, H, and I (- pages 75–81) (to set up and use personal e-mail and e-mail scheduling).

If the file sharing and/or personal e-mail and e-mail

scheduling features work correctly, then the

automatic network address setup was successful (even though the TV displayed the error message).

Manually setting up the network address

This setup requires the data listed below. You can get this

data from either your ISP or the configuration utility for your DSL/cable modem or router.

IP address:

___ ___ ___ . ___ ___ ___ . ___ ___ ___ . ___ ___ ___

Subnet mask:

___ ___ ___ . ___ ___ ___ . ___ ___ ___ . ___ ___ ___

Gateway (Router) address:

___ ___ ___ . ___ ___ ___ . ___ ___ ___ . ___ ___ ___

DNS (Domain Name Server) address:

___ ___ ___ . ___ ___ ___ . ___ ___ ___ . ___ ___ ___

8 Press b to highlight the Gateway (Router) field, and

then use the Number buttons to input the Gateway (Router) address.

9 Press b to highlight the DNS (Domain Name Server)

field, and then use the Number buttons to input the DNS address.

10 When finished, highlight Done and press T.

The Basic Network Setup menu closes and the

Network menu appears.

11 Go to section C, “Setting up file sharing on your PC.”

1 Press Y and open the Setup menu. 2 Highlight Installation and press T. The Installation

menu appears.

3 Open the Network menu. 4 Highlight Basic Network Setup and press T. 5 The message “Obtain network address automatically?”

appears. Highlight No and press T.

Basic Network Setup

Obtain network address automatically?

Yes No

6 The Basic Network Setup menu appears.

Press B or b to highlight the IP Address field, and then use the Number buttons on the remote control to input the IP address.

Basic Network Setup

Please enter your Network Address Information

DNS (Domain Name Saver)

IP Address

Subnet Mask

Gateway (Router)

Cancel Done

0 000

225 225 225 0

000 0

7 Press b to highlight the Subnet Mask field, and then use

the Number buttons to input the Subnet Mask.

Chapter 7: Using the THINC™ home network feature

Resetting the network address

Press Y and open the Setup menu.

2 Highlight Installation and press T. The Installation

menu appears.

3 Open the Network menu. 4 Highlight Basic Network Setup and press T. 5 The message “Your Basic Network Setup is complete.

Would you like to start over?” will appear. To continue, highlight Yes and press T. To return to the Network menu, highlight No and press

Basic Network Setup

Your Basic Network Setup is complete. Would you like to start over?

Yes No

6 If you selected Yes in step 5, the message “Obtain

network address automatically?” will appear.

Basic Network Setup

Obtain network address automatically?

Yes No

To obtain the network address automatically, go to step 5 under “Automatically setting up the network address” (- page 61).

To manually enter the network address, go to “Manually setting up the network address.”

For home network troubleshooting tips, see Chapter 8.

C. Setting up file sharing on your PC

Compatible operating systems

The following operating systems are compatible for file sharing with the TV:

• Microsoft

(Home Edition and Professional) [See setup details below]

• Microsoft

(Home Edition and Professional) [See setup details below]

• Microsoft

No other operating systems are compatible with the TV.

Note:

• The name of any directory/folder on your PC that you are setting up for file sharing with the TV cannot be longer than 12 characters and cannot contain any special characters.

• See “Media specifications” (- page 67) for details on compatible JPEG and MP3 files.

• The network (NETBIOS) name of your PC that you are setting up for file sharing must be 15 characters or less.

To determine which operating system and service pack (if applicable) are on your PC:

1 On your PC, click the “Start” button. 2 Click “Settings | Control Panel.” 3 In the Control Panel, double-click “System.” 4 Select the “General” tab, which will display your PC’s

current operating system and service pack.

Windows® XP Service Pack 2

Windows® XP Service Pack 1

Windows® 2000 [See setup details on page 65]

Setting up file sharing on a PC with Microsoft

Windows® XP Service Pack 1 or

Service Pack 2

On your PC:

a) Right-click the folder to be shared.

b) Click “Sharing and Security...” (which will open the Properties window for the selected folder.)

* Microsoft product screen shot(s) reprinted with permission from

Microsoft Corporation.

(continued)

Chapter 7: Using the THINC™ home network feature

2 If the “Sharing” tab on your PC does not have a

“Permissions” button, follow step 2.1 below. If the “Sharing” tab on your PC has a “Permissions” button, follow step 2.2 below.

2.1

Go to section D, “Setting up file sharing on the TV,” on page 66.

2.2

3 In the Permissions window for the selected folder:

4 Go to section D, “Setting up file sharing on the TV,” on

page 66.

Go to step 3.

Chapter 7: Using the THINC™ home network feature

Setting up file sharing on a PC with Microsoft

On your PC:

a) Right-click the folder to be shared.

b) Click “Sharing...” (which will open the Properties window for the selected folder).

Windows® 2000

2 In the Properties window for the selected folder:

a) Click to display the “Sharing” tab.

4 In the Properties window:

Click “OK” (which closes the Properties window).

5 The shared folder will display with a “shared folder” icon

(a hand holding a folder).

b) Click to select “Share this folder.”

c) Click “Permissions” (which will open the Permissions window for the selected folder).

3 In the Permissions window for the selected folder:

a) Click “Add...” and then select the user to be given sharing privileges.*

*This user must match the user stored in the TV’s “Home File Server Setup” menu.

b) Click to check “Allow” next to “Full Control.”

c) Click “Apply.”

d) Click “OK” (which closes the Permissions window).

6 Go to section D, “Setting up file sharing on the TV,” on

the next page.

For home network troubleshooting tips, see Chapter 8.

Chapter 7: Using the THINC™ home network feature

D. Setting up file sharing on the TV

1 Press Y and open the Setup menu. 2 Highlight Installation and press T. The Installation

menu will appear. Open the Network menu.

Network

Basic Network Setup

Personal E-mail Setup

E-mail Scheduling Setup

Home File Server Setup

Software Upgrade

Navigate

3 Highlight Home File Server Setup and press T. The

Home File Server Setup window will appear.

After a few moments, the message “Please Wait...” will appear until the network finds your networked PC.

The networked PC will act as the “Home Server” for file sharing with the TV.

Home File Server Setup

Please enter your Home Server Setup Information.

Home Server Name

User Name

Password

JPEG Picture Directory

MP3 Music Directory

Software Upgrade Directory

Cancel Done

Select

Back Exit

CH RTNENTER

EXIT

ABCD

XYZ

*******

JPEG

MP3

7 Press Bb to highlight either JPEG Picture Directory

or MP3 Music Directory.

Note: The first time you highlight either of these fields, the message “Please Wait...” will appear until the field is populated with the files in your PC’s shared folder(s).

Home File Server Setup Please Wait...

Please enter your Home Server Setup Information.

Home Server Name

User Name

Password

JPEG Picture Directory

MP3 Music Directory

Software Upgrade Directory

Cancel Done

ABCD

XYZ

*******

8 Press C c to select the shared folder (on your PC) that

contains the JPEG and/or MP3 files you want to view/play on the TV.

Note: Make sure you select the correct folder in this step.

9 To exit the window and save your settings, highlight

Done and press T.

To exit the window without saving your settings, highlight

Cancel and press T.

4 Press Bb to highlight Home Server Name, and then

press C c to select the name of the PC you set up for file sharing.

If you have multiple PCs on your home network that have shared folders, press C c to select the PC (home server) from which you want to access files.

Home File Server Setup

Please enter your Home Server Setup Information.

Home Server Name

User Name

Password

JPEG Picture Directory

MP3 Music Directory

Software Upgrade Directory

Cancel Done

ABCD

XYZ

*******

JPEG

MP3

5 a. Press Bb to highlight User Name and then press T

to open the software keyboard for that field.

b. Enter the User Name for your PC using the software

keyboard. See “Using the software keyboard” on the next page.

Note: The User Name is case sensitive.

c. When finished entering all characters, highlight Done

and press T.

6 Repeat step 5 for the Password field.

Note: The Password is case sensitive.

Chapter 7: Using the THINC™ home network feature

Using the software keyboard

Typing text on the software keyboard is similar to typing text on a cell phone. The number keys on the remote control have corresponding letters or symbols printed next to them. Repeatedly press a key to toggle through the available characters for that key.

For example, repeatedly pressing the “q” key toggles through several punctuation symbols and the numeral 1; repeatedly pressing the “w” key toggles through the letters a, b, and c, and the numeral 2, and so forth.

To enter text using the software keyboard:

1 Repeatedly press the corresponding key on the remote

control to highlight the desired character on the on-screen software keyboard.

2 The highlighted character is entered after you either press

a different key, press the c key, or after a two-second pause.

3 Repeat steps 1 and 2 until you have entered all desired

text.

Software keyboard example

1 . , ? ! : ; a b c 2 A B C

g h i 4 G H I

p q r s 7 P Q R S

Backspace

100

& $

@% # ~ _ | \ `

j k l 5 J K L

t u v 8 T U V

0 ' " ( ) =/ + - ^ <* > [ ] { }

d e f 3 D E F

m n o 6 M N O

w x y z 9 W X Y Z

INPUT

Space

4 Press R to close the software keyboard and return to the

previous screen.

Note: Help instructions are provided in the on-screen display and include specific remote control key functions that are applicable only in certain views.

For example: x X = page up and down.

Z = Home. z = End of Line.

T = New Line. O = Closes the screen WITHOUT saving entries.

About the Software Upgrade feature

This feature allows you to download software updates to your television from a shared folder on your home network. If you experience any difficulties that can only be resolved by a software update, your Toshiba customer service representative will provide you with the appropriate upgrade files and assist you in the proper use of this feature.

E. Viewing/playing shared files on the TV

You can use the Picture Viewer to view compatible JPEGformat photos on the TV.

You can use the Audio Player to play compatible MP3 files on the TV.

The TV can access JPEG and/or MP3 files stored on a networked PC (as described on pages 68–70 in this Guide and also in the Installation Guide).

Note:

• If you are viewing/playing files stored on a networked PC, IT IS RECOMMENDED THAT YOU BACK UP YOUR DATA. Toshiba is not liable for any damage caused by the use of any networked PC or shared files with this TV. Toshiba will not compensate for any lost data or recording(s) caused by the use of such PCs or data.

• The technical criteria set out in this manual are meant as a guide only.

• You must obtain any required permission from copyright owners to download or use copyrighted content. Toshiba cannot and does not grant such permission.

Media specifications

File/folder name specifications

– Maximum file name length: 255 characters. – Maximum shared folder* name length: 12 characters. – File names must contain US-ASCII characters only. – File and folder names cannot contain any special

characters, such as \ / : ? “ ” < > | .

* The words “folder” and “directory” are used interchangeably.

Picture Viewer/JPEG file specifications

– Maximum JPEG file size: 8 MB

• JPEG files larger than 8 MB will not display.

– Maximum JPEG image resolution: 6000 5 4000 pixels

• Images with a resolution higher than 6000 5 4000 pixels

will not display.

– The Picture Viewer is designed to display only pictures

stored in compatible JPEG formats with a file extension of “.jpg.”

– JPEG images processed and/or edited on a personal

computer (PC) may not display properly or at all.

– Some digital cameras may store images in a format that is

not compatible with the TV.

– JPEG files stored on a networked PC that are not in a file

and folder format compatible with the TV will not

display on the TV.

(continued)

Chapter 7: Using the THINC™ home network feature

Audio Player/MP3 file specifications

– Maximum MP3 file size: 50 MB

• MP3 files larger than 50 MB will not play.

– The Audio Player is designed to play only music files

stored in compatible MP3 formats with a file extension of “.mp3.”

– MP3 files processed and/or edited on a PC may not play

properly or at all. Some MP3 files may be in a format that is not compatible with the TV.

– MP3 files must be in the following format:

• MPEG1 (ISO/IEC 11172-3) Layer3.

• Sampling frequency—MPEG1: 32 kHz, 44.1 kHz,

48 kHz.

• Bitrate—MPEG1: 32–320 kbps.

• Channels—Stereo, Joint stereo, Dual channel, Single

channel.

• ID3 Ver. 1, Ver. 2.

– The meta-data for MP3 files (artist name, album name,

song title, etc.) must be in the following format:

ISO-8859-1 (US-ASCII/ Western European) character sets

– MP3 files stored on a networked PC that are not in a file

and folder format compatible with the TV will not play

on the TV.

Networked PC specifications

Maximum number of files per shared folder:

– JPEG = 1,000

• All JPEG files over the 1,000th in a shared folder will not display.

– MP3 = 200

• All MP3 files over the 200th in a shared folder will not play.

Maximum number of nested folder levels: 10 levels

• Files in folders more than 10 levels down from the top level

folder will not display/play.

• See pages 60–66 for details on networking your TV and PC

for file sharing.

Using the Picture Viewer

You can use the TV’s Picture Viewer to display your digital photos (JPEG files) on your TV’s screen in thumbnail mode or as a slide show.

Note:

• You cannot use the Picture Viewer and Audio Player at the same time.

• You must obtain any required permission from copyright owners to download or use copyrighted content. Toshiba cannot and does not grant such permission.

Accessing JPEG files stored on a networked PC

1 Make sure you have correctly set up your home network

and file sharing (- pages 60–66 in this Guide; also see the Installation Guide).

2 Press Y and open the Applications menu. 3 Highlight Picture Viewer and press T.

Applications

Picture Viewer

Audio Player

Personal E-mail

Channel Browser

TV Guide On Screen

Digital CC/Audio Selector

CableCARD

Navigate

Select

Back Exit

CH RTNENTER

EXIT

If the network is available, it will retrieve the JPEG picture list via the network.

4 Press B or b to access the folder or directory that contains

the JPEG pictures you want to view.

Picture Viewer

//BEARD-DESK/C

Copy of isi mip

IQAWG_A

INCD

isiImip

WINNT

Documents and Settings

ExitSelectImage Select

EXIT

ENTERCH RTN

Navigate

To expand a particular folder to view a list of images, press c on the folder.

To close the folder or directory, press C on the folder. Pressing C on a file will move the focus up to the folder

that contains the file. Pressing c on a file will move the focus down to the next

folder. If you press T on a particular folder, the first file in the

folder will be displayed as the first file in the thumbnail list.

If you press T on a particular file, that file will be displayed as the first file in the thumbnail list.

Note: You can use R to toggle between the thumbnail and folder views. The last item selected will be highlighted upon return to the Picture Viewer.

Chapter 7: Using the THINC™ home network feature

Viewing JPEG files on the TV

1 After accessing your JPEG files from your networked PC

(- page 68), the images automatically display on-screen, with one as a large picture and six in thumbnail format.

Picture Viewer

//ALLENMPC/Pics/Directory3/Subdirectory1/shelby concept.jpg.

1 of 8

Nov 2 05

2 of 8

Jun 25 01

3 of 8

Feb 10 05

4 of 8

Feb 8 05

5 of 8

Jun 25 01

6 of 8

Feb 10 05

Rotate Next

ENTERCH RTN

ExitSlide ShowCHPage Up/DownFile Select

EXIT

2 Press C to rotate the large picture 90° counterclockwise.

Picture Viewer

//ALLENMPC/Pics/Directory3/Subdirectory1/shelby concept.jpg.

1 of 8

Nov 2 05

2 of 8

Jun 25 01

3 of 8

Feb 10 05

4 of 8

Feb 8 05

5 of 8

Jun 25 01

6 of 8

Feb 10 05

Rotate Next

ENTERCH RTN

ExitSlide ShowCHPage Up/DownFile Select

EXIT

3 Press c to rotate the large picture 90° clockwise.

Picture Viewer

//ALLENMPC/Pics/Directory3/Subdirectory1/shelby concept.jpg.

1 of 8

Nov 2 05

2 of 8

Jun 25 01

3 of 8

Feb 10 05

4 of 8

Feb 8 05

5 of 8

Jun 25 01

6 of 8

Feb 10 05

Rotate Next

ENTERCH RTN

ExitSlide ShowCHPage Up/DownFile Select

EXIT

4 Press B or b to select another picture as the large picture. 5 Press T to view your pictures in a slide show.

To set the slide show interval:

1 Press O to close the Picture Viewer (if it is open). 2 Press Y and open the Setup menu. 3 Highlight Slide Show Interval and press T. 4 Select the interval from the menu sidebar (2, 5, 10, 15, or

20 seconds).

Setup

Installation

Sleep Timer

On/Off Timer

PC Settings

PC Audio HDMI 1 Audio

Slide Show Interval

Navigate

Select

To view your JPEG files in Native Resolution mode:

Press < or , during the slideshow. This will expand the image to its non-compressed format.

Press E to display a help bar that will show how to scroll to the edges of the image using the Bb C c buttons.

To exit Native Resolution and return to the normal slideshow, press T.

To return to the thumbnail view, press either O or R. If an image is too large to display in Native Resolution mode (6MB), a warning message will display.

To close the Picture Viewer:

Press O to close the Picture Viewer and return to the regular TV screen.

Auto

2 Sec

CH RTNENTER

2 Sec

5 Sec

10 Sec

15 Sec

20 Sec

Back Exit

EXIT

During the slide show:

• To stop on an image during the slide show, press T.

• To resume the slide show, press T again.

• To rotate the picture, press C or c.

• To select another image, press B or b.

• To stop the slide show and return to the picture viewer, press

• To stop the slide show and return to the regular TV screen,

press O.

Chapter 7: Using the THINC™ home network feature

Using the Audio Player

You can use the TV’s Audio Player to listen to MP3 files on the TV.

Note:

• Make all desired adjustments to the TV’s audio features (e.g., surround, bass, treble, balance) before starting the Audio Player.

• You cannot use the Picture Viewer and Audio Player at the same time.

• You must obtain any required permission from copyright owners to download or use copyrighted content. Toshiba cannot and does not grant such permission.

Playing MP3 files stored on a networked PC

1 Make sure you have correctly set up your home network

and file sharing (- pages 60–66 in this Guide; also see the Installation Guide).

2 Press Y and open the Applications menu. 3 Highlight Audio Player and press T.

Applications

Picture Viewer

Audio Player

Personal E-mail

Channel Browser

TV Guide On Screen

Digital CC/Audio Selector

CableCARD

Navigate

Select

Back Exit

CH RTNENTER

EXIT

If the network is available, the TV will retrieve the MP3 file through the network.

4 Press B or b to access the folder or directory that contains

the MP3 files you want to play.

If you press T on a particular folder, the first file in the folder will display as the first file in the list in Song Select view.

If you press T on a particular file, that file will display as the first file in the list in Song Select view.

Note: You can use R to toggle between the thumbnail and folder. The last item selected will be highlighted upon return to the Audio Player.

Audio Player

//ALLENMPC/MP3's/Dir1/Sub1/03-Moonlight Sonata.mp3

Title

Ser No.1 in D, Op.11... SCO/Sir Charles...

Requiem, Op. 5: IV. R... Robert Shaw/Atla...

Rapsodie Espagnole:... Jesus Lopez-Cobo...

III. Sanctus: Sanctu... Boston Baroque/M...

Piano Sonata, K. 545... A-M Classical

Pathétique Sonata, m... A-M Classical

Chopin Prelude No. ... Andrys

Piano Sonata, K. 545...

Moolight Sonata, mo...

Artist

A-M Classical

Navigate

Moolight Sonata, movement

A-M Classical

EXIT

ENTERCH RTN

VOL

ExitSelectFile Select

5 The Audio Player will begin playing the first MP3 file

in the list. Press BbC c to navigate to the rewind, pause, fast forward, skip backward, skip forward, volume, and mute buttons—or to select another MP3 file—and then press T.

To adjust or mute the volume:

Press z Z or W on the remote control (see page 43 for details on muting the sound), or press Bb C c to navigate to the on-screen VOL and MUTE ( ) buttons and press T.

To close the Audio Player:

Press O to close the Audio Player and return to the regular TV screen.

Audio Player

//ALLENMPC/MP3's/Dir1/Queen - pain Is Close to Pleasure.mp3

MP3,s

Dir 1

Sub 1

03 - Take Five.mp3

Lá Breá Fán Dtuath.mp3

04 05 - An Tûll.mp3

Sub 2

Dir 2

Queen - A Kinnd of Magic.mp3 Queen - Forever.mp3 Queen - Gimme the Prize.mp3 Queen - One Vision.mp3

Queen - Pain is So Close to Pleasure.mp3 Simon and Garfunkel - Cecilial.mp3

Navigate

ENTERCH RTN

EXIT

VOL

ExitSelectSong Select

To expand a particular folder to view a list of images, press c on the folder.

To close the folder, press C on the folder. Pressing C on a file will move the focus up to the folder

which contains the file. Pressing c on a file will move the focus down to the next

folder.

Chapter 7: Using the THINC™ home network feature

F. Setting up the Personal E-mail

4 Highlight Personal E-mail Setup and press T.

feature

The Personal E-mail feature allows you to access your e-mail server through the TV. You can create, view, reply to, and forward personal e-mails and JPEG format picture attachments.

IMPORTANT NOTE

If you connect the TV to the Internet, anyone with access to the TV will be able to configure the TV to access e-mail accounts for which they have account access information (user name, password and server addresses).

If you set up any personal e-mail accounts on the TV, anyone with access to the TV will be able to read e-mail from those accounts unless you lock the profile for each e-mail account (- page 71, step 8).

You should consider these factors when deciding whether to set up personal e-mail accounts and whether to keep the TV set connected (or make available easy connection) to the internet.

The Personal E-mail Setup will allow up to 4 users to set up profiles from which each profile may access their e-mail account.

Required information and services

Before you can set up the personal e-mail feature, you must have the following information and related services:

a) A valid POP3 e-mail account that you normally use to

receive e-mails.

b)Login and password settings for above. c) Name or IP address of the incoming (POP3) mail server. d)Name or IP address of the outgoing (SMTP) mail server.

To obtain the required e-mail services listed above, contact your ISP.

To obtain the required addresses and settings listed above, either contact your ISP or use the configuration utility for your DSL/cable modem or router.

Setting up personal e-mail

Press Y and open the Setup menu.

2 Highlight Installation and press T. The Installation

menu appears.

3 Open the Network menu.

Network

Basic Network Setup

Personal E-mail Setup

E-mail Scheduling Setup

Home File Server Setup

Software Upgrade

Navigate

Select

Back Exit

CH RTNENTER

EXIT

5 The Personal E-mail Setup window appears.

Press B or b to highlight one of the blank profiles and press T.

Personal E-mail Setup

Please select a profile

Note: If all four profiles have been created, you can select an existing profile and modify it.

6 The E-mail Profile Setup window will appear.

E-mail Profile Setup

Display Name

Check for New Mail

Profile Lock

Cancel

E-mail Account Setup

Enter PIN Code

Every 5 minutes

Disabled

Done

Highlight the Display Name field and press T. The software keyboard will appear.

Software keyboard example

1 . , ? ! : ; a b c 2 A B C

g h i 4 G H I

p q r s 7 P Q R S

Backspace

100

& $

@% # ~ _ | \ `

j k l 5 J K L

t u v 8 T U V

0 ' " ( ) =/ + - ^ <* > [ ] { }

d e f 3 D E F

m n o 6 M N O

w x y z 9 W X Y Z

INPUT

Space

Use the software keyboard to enter the display name. (“Using the software keyboard” on page 67).

7 Press b to highlight Check for New Mail, then press C

or c to select your desired setting.

• You can choose to have the TV check for new e-mail

every 5, 15, 30 minutes, or 1 hour. When the Check for New Mail interval is set to DISABLED, new e-mail notifications will not appear.

8 You can use the Profile Lock to protect your profile

settings and prevent other users from viewing your personal e-mails.

Note: Each of the four e-mail profiles must be locked individually.

To lock an e-mail profile:

a) Press b to highlight the Profile Lock field. b)Press C or c to select Enabled.

(continued)

Chapter 7: Using the THINC™ home network feature

c) Highlight the Enter PIN Code field and press T.

E-mail Profile Setup

Display Name

Check for New Mail

Profile Lock

Cancel

E-mail Account Setup

Enter PIN Code

Every 5 minutes

Enabled

Done

d)Use the Number buttons to enter a four-digit PIN code. e) Enter the code a second time to confirm, and then press

E-mail Account Setup

Please enter a 4 digit PIN code

****

Confirm PIN code

****

Cancel Done

Note: If the profile is already locked, the E-mail Profile Unlock window will appear. You must enter the correct

PIN code to unlock the account.

E-mail Profile Unlock

Please enter the 4 digit PIN code

****

Using the software keyboard, enter the appropriate information in the fields.

• E-mail Address

• POP3 Server Address

• POP3 Port Number (uses default if left blank)

• POP3 User Name (same as e-mail account login)

• POP3 Password: password

• SMTP Server Address

• SMTP Port Number (uses default if left blank)

• SMTP Authentication: Press C or c to select either Not

required, Same as POP3, or Different from POP3.

• SMTP User Name

• SMTP Password

See “Description of fields in the E-mail Account Setup window” (- page 78) for details on the settings for these fields.

11 Highlight Test and press T to confirm that the e-mail

account settings work correctly. During testing, the TV will display the following

message.

E-Mail Account Test

Connecting to POP3 server...

Cancel

Done

If you cannot remember your PIN code, while the E-mail Profile Unlock window is displayed, press E four (4)

times within five (5) seconds. The PIN code will be cleared and you can enter a new PIN code.

9 Highlight the E-mail Account Setup field, and

press T.

E-mail Profile Setup

Display Name

Check for New Mail

Profile Lock

E-mail Account Setup

Cancel

The E-mail Account Setup window appears (illustrated below).

E-mail Account Setup

E-mail Address

POP3 Server Address

POP3 Port Number

POP3 User Name

POP3 Password

SMTP Server Address

SMTP Port Number

SMTP Authentication

SMTP User Name

SMTP Password

Test Done

Enter PIN Code

Cancel

Every 5 minutes

Enabled

Done

Not required

Cancel

12 When testing is finished, a message will appear indicating

whether the e-mail account test passed or not.

If the e-mail account test succeeds, the following message appears:

E-Mail Account Test

All tests were successful.

If the e-mail account test fails, the following message appears:

E-Mail Account Test

All tests failed.

Make sure you entered the correct information for the fields in the E-mail Account Setup window.

13 Press T. 14 To exit the window and save your settings, highlight

Done and press T.

To exit the window without saving your settings, highlight

Cancel and press T.

10 Highlight a field and press T. The software keyboard will

appear (as shown in step 6).

Note: The software keyboard layout will vary based on the buttons that are available for the current item.

Chapter 7: Using the THINC™ home network feature

G. Using the Personal E-mail feature

The Personal E-mail feature allows you to:

1)Create new e-mails.

2)View and reply to received messages.

3)Forward received messages (including messages with attached JPEG files)

4)View attached JPEG files. (Users will not be able to attach files to messages that they send.)

In addition, you can create up to four different user e-mail accounts, which can be locked to prevent unwanted access (- page 71).

You can access the personal e-mail feature in any of the following ways:

• Select Personal E-mail from the Applications menu.

• Open the THINC menu and select Personal E-mail.

• Press T when the “unread e-mail notification” appears

(see below).

Unread E-mail Notification

When the TV detects unread e-mail in a user’s inbox, a notification will appear in the bottom right corner of the screen that contains the envelope icon, user’s name, and number of unread messages.

E-mail Inbox

To open the Inbox, press T while the unread e-mail notification is on-screen.

In the Inbox view, unread e-mails are denoted by an envelope icon.

Personal E-mail Inbox Adam

Refresh

Navigate

From Received Subject

Anne

Nancy

Kent

Ben

Lucy

Nakata

Ichiro

Eve

Ben

Nancy

Read Page New Message

ENTER

PAGE

Elements of the Inbox

1 PIP window

When the Inbox is open, you can continue watching the current channel in the PIP (picture-in-picture) window in the upper left corner of the screen. You can change channels in the PIP window by pressing < / , on the remote control (unless the TV is currently recording.)

2 From, Received, and Subject information.

3 User name

07/14/06 10:40 AM

09/14/06 10:40 AM

09/14/06 10:50 AM

09/14/06 11:10 AM

09/14/06 11:15 AM

09/14/06 11:20 AM

09/14/06 11:30 AM

09/14/06 11:40 AM

09/14/06 11:48 AM

09/14/06 11:55 AM

Pictures

Fw:Pictures

E-mail

Pictures

Fw: Fwd: FW: Party

Fw: Party

Re: Party

Party

RE: Happy Birthday

Re: Happy Birthday

Exit

EXIT

Delete

my name x 57

Note:

• You can specify the frequency at which the TV checks for unread e-mails by selecting Check for New Mail in the E-mail Profile Setup menu (- page 71, step 7).

• The unread e-mail notification will not display when other applications are running (such as the Picture Viewer or Audio Player).

• The unread e-mail notification will not appear in any video recorded from the TV using the video outputs.

To open the Inbox, press T while the unread e-mail notification is on-screen.

To dismiss the unread e-mail notification and continue watching TV, press O.

4 Scroll arrows

Press Bb to scroll through messages one-by-one. Press x / X to scroll through messages page by page. The Inbox can hold a maximum of 100 messages.

5 Refresh button

The Refresh button checks for new messages and deletes messages marked with the Trash Can icon (see below). To refresh the Inbox, highlight the Refresh button and press T .

6 The following icons convey information about messages

in the Inbox:

Trash Can icon

The Trash can icon denotes a message marked for deletion. To mark a message for deletion, highlight the message and press j. To unmark the message (and remove the trash can icon), press j again. To delete all messages marked with the Trash Can icon, refresh the Inbox (see item 5, above).

Envelope icon

The Envelope icon denotes a new, unread message. After the message is viewed, the envelope icon disappears.

(continued)

Chapter 7: Using the THINC™ home network feature

Envelope with paperclip icon

The Envelope with paperclip icon denotes a new message with a JPEG attachment.

Paperclip icon

The Paperclip icon denotes a message with a JPEG attachment.

“No Entry” icon

The No Entry icon denotes a message that is too large to open. The maximum allowable message size is 300 KB.

Note: If you delete an e-mail on the TV, it will also be deleted from the e-mail server identified in the account setup—even if the message indicates that it cannot be read by the TV.

7 Read, New Message, Delete

From the Inbox view, you can reply to messages, forward messages, delete messages, or create new messages by pressing the appropriate buttons (as shown in the guide at the bottom of the screen). You cannot add attachments to an outgoing e-mail, but you can forward an e-mail that includes attachments.

Note: If you delete an e-mail on the TV, it will also be deleted from the e-mail server identified in the account setup—even if the message indicates that it cannot be read by the TV.

8 Exit

Press O to close the Personal E-mail feature and return to the regular TV screen on the last channel viewed.

Read View

To read e-mail:

From the E-mail Inbox window, highlight the e-mail you want to read and press T. The Read view (illustrated below) will appear.

Personal E-mail Read Adam

From: "Nancy" <Nancy@XXXX.com> To: "my TV" <Tom @cXXX.net > Cc: Subject: FW: Pictures

xxxxxxx xxxx xxxxxxxxxxxxxxx

Xxxxxxxx xxxxxx xxxx xxxxxxx xxxxxxxxx xxxx xx xxxxxxxxxxx xxxxxxxx xxxxxx xxxxxxx. Xxxxx xxxxxx xx xxxxxx xxxxxxxxx xxxxxxxxxx xxxxxx xxx xxxxxxxxx xxxxxxxxxxxxxxxx xxxxxx.

Xxx xxxxx xxxxxxxxx xxxxxx

1. xxxxxxxx xx xxx x x xxxxxxxxxx xxxxxxxxxx

2. xxxxxx xxxxxx xx xxxxxxxxx xxx xxxxxxxxxx xxxxx xxx x x xxxxxx xxxx

3. xxxxx xxxxxx xxxx xxxxxxx xxxxxx xxxxxxxxxxxxxxxx (xxxxxxxx xx xxxxxxxx xxxxx xxxxx)

4. xxxxxx xxxxxx xx xxxxxx xxxxx, xxxxxxxxx

5. xxx xxxxxx xxxxxxx xxxxxx xxxxxxxxxx xxxxxxxxxxx xxx xxxxxxx

6. xxxx xxxxxxxx xxxxxxxxxxxxx xxxxxxxx xx xxxxxxx xxxxxxxxx xxxxxxxxx

7. xxxxxxx xxxxxxx xxxx xxxxxxxxxxxxx xxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxx

ENTER

Navigate

jPEG x 5

JPEG Back

CH RTN

From the Read view, press B b to scroll up and down to view the entire message.

To reply to the current message, press f. If the e-mail has more than one recipient, press g to reply to

all (attachments will be discarded). To forward an e-mail to other recipients, press h

(attachments will be included). To view a JPEG attachment using the Picture Viewer,

highlight the Paperclip icon and press T. To return to the Read View from the Picture Viewer, press O.

To return to the Inbox View from the Read view, press R. To close the Personal E-mail feature and return to the regular

TV screen on the last channel viewed, press O at any time.

+PAGE

unknownx 1

PAGE-

ReplyBReply AllCForwardPage

EXIT

Exit

Chapter 7: Using the THINC™ home network feature

Message editing views

To edit a field when creating an e-mail:

1 Repeatedly press BbC c to highlight the field (To, Cc,

Subject, etc.).

2 Press T to edit the field.

From the Read View, you can reply or forward the message (- page 74), and the screen will enter Message Editing view.

Personal E-mail Reply Adam

From: "Adam" <Adam@XXXX.com> To: "Tom" <Tom @cXXX.net > Cc: Subject: Re: Pictures

Hello

--------------------.Original message: From: "Tom" To: "Adam" Received: from xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx Subject: Picture

1 . , ? ! : ; a b c 2 A B C

g h i 4 G H I

p q r s 7 P Q R S

Backspace

100

& $

Cursor

@% # ~ _ | \ `

ENTER

Select

New Line

Edit

ENTER

CancelASend

CH RTN

j k l 5 J K L

t u v 8 T U V

0 ' " ( ) =/ + - ^ <* > [ ] { }

Back

CH RTN

+PAGE

PAGE-

Exit

EXIT

HomePage End

d e f 3 D E F

m n o 6 M N O

w x y z 9 W X Y Z

INPUT

Space

Exit

EXIT

To send a message to more than one recipient:

1 Highlight the “To” or “Cc” field. 2 Press T. 3 Highlight “Add new recipient.” 4 Press T.

To delete a recipient:

1 Highlight the recipient to be deleted.

Personal E-mail Address List (To:) Adam

Tom @cXXX.net

Add new recipient

Select

ENTER

Edit BackDDelete

CH RTN

EXIT

Exit

2 Press j. 3 Highlight YES to confirm deletion.

Delete the selected recipient?

YesNo

4 Press T.

H. Setting up e-mail scheduling

You can remotely schedule and delete recordings and reminders by sending an e-mail to the TV from any PC.

Note:

• If you have not already done so, follow the instructions in

sections A and B (- page 60), before proceeding.

• Before you can schedule recordings, the time and date in

the TV Guide On Screen feature must be set (- “Setting the time and date” on page 28).

Required information and services

Before you can set up the e-mail scheduling feature, you must have the following information and related services:

a) A valid POP3 e-mail address dedicated for use by the TV

only.

Note: The e-mail address assigned to the TV must be a dedicated POP3 address, different from your personal e-mail address. Assigning your personal e-mail address to the TV will eventually lead to the deletion of all of your personal e-mails (including attachments). This is NOT covered under the Toshiba warranty.

b)A personal e-mail address (different from the TV’s

dedicated e-mail address) from which you can send e-mails to the TV.

c) Login and password settings for the TV’s POP3 e-mail

account. d)Name or IP address of the incoming (POP3) mail server. e) Name or IP address of the outgoing (SMTP) mail server.

To obtain the required e-mail services listed above, contact your ISP. You may also be able to use the “home page” or “configuration portal” supplied by your ISP to configure additional e-mail accounts.

To obtain the required addresses and settings listed above, either contact your ISP or use the configuration utility for your DSL/cable modem or router.

Note:

• Toshiba is not responsible for any damage or loss

caused directly or indirectly by the failure of the e-mail

scheduling feature to record content intended to be

recorded.

• Toshiba is not responsible for, nor has any control over,

any content recorded and/or viewed using the e-mail

scheduling feature. Further, the e-mail scheduling

feature is not meant to be used for unauthorized

recording and/or viewing of copyrighted works.

• The recording, use, distribution or revision of television

programs, videotapes, DVDs and other materials in

violation of applicable laws (including copyright law)

and/or agreements may subject you to criminal and civil

liability.

For home network troubleshooting tips, see Chapter 8.

Chapter 7: Using the THINC™ home network feature

Setting up e-mail scheduling

Press Y and open the Setup menu.

2 Highlight Installation and press T. The Installation

menu appears.

3 Open the Network menu. 4 Highlight E-mail Scheduling Setup and press T. The

E-mail Scheduling Setup window opens.

E-mail Scheduling Setup

E-mail Scheduling

Check for New Mail

ID Required

Authorized E-mail

Cancel

E-mail Account Setup

Every 5 minutes

Yes

Done

5 Enter the required data in the fields.

See “Description of fields in the E-mail Scheduling Setup window” (- page 77) for details on the settings for these fields.

• For the fields listed below, press B or b to highlight the

field, and then press C or c to select the settings:

– E-mail Scheduling: On or Off – Check for New Mail: Options are 5 min,

15 min, 30 min and 1 hour.

– ID Required: Yes or No

• For the fields listed below, press B or b to highlight the

field, press T to open the software keyboard, and then enter the required information using the software keyboard:

–ID – Authorized E-mail

1 a b c 2 A B C

g h i 4 G H I

p q r s 7 P Q R S

Display Name

Backspace

100

Check for New Mail

Authorized E-mail

j k l 5 J K L

t u v 8 T U V

E-mail Account Setup

See “Using the software keyboard” (- page 67) for instructions on entering data in the fields.

d e f 3 D E F

m n o 6 M N O

w x y z 9 W X Y Z

Every 5 minutes

DoneCancel

6 Highlight E-mail Account Setup, then press T. The

E-mail Account Setup window will appear.

E-mail Account Setup

E-mail Address

POP3 Server Address

POP3 Port Number

POP3 User Name

POP3 Password

SMTP Server Address

SMTP Port Number

SMTP Authentication

SMTP User Name

SMTP Password

Test Done

Not required

Cancel

7 Enter the data in the fields as you did in step 5. See

“Description of fields in the E-mail Account Setup window” (- page 78) for details on the settings for these fields.

For the fields listed below, B or b to highlight the field, press T to open the software keyboard, and then enter the required information using the software keyboard:

– E-mail Address – POP3 Server Address –POP3 Port Number – POP3 User Name – POP3 Password – SMTP Server Address – SMTP Port Number – SMTP User Name – SMTP Password

For the SMTP Authentication field, press B or b to highlight the field, and then press C or c to select the appropriate setting (Not required, Same as POP3,

Different from POP3).

8 When you are finished entering all characters for the

selected field, highlight Test and press T to test the e-mail setup.

During testing, the TV will display the E-Mail Account Test window.

Note: Depending on your configuration, the e-mail test can take several minutes. Do not press O during this time.

9 When testing is finished, a message will appear indicating

whether the e-mail test passed or not.

If the e-mail test succeeds:

The message “All tests were successful” (shown below) will appear.

E-Mail Account Test

All tests were successful.

Chapter 7: Using the THINC™ home network feature

If the e-mail test fails:

a) An error message will appear (similar to the example

below).

E-Mail Account Test

All tests failed.

b)Ensure that you entered the correct information for the

fields in the E-mail Account Setup window. Repeat steps 7–8.

10 To exit the E-mail Scheduling Setup window and

save your settings, highlight Done and press T. To exit the E-mail Scheduling Setup window without

saving your settings, highlight Cancel and press T.

IMPORTANT NOTE

To use e-mail scheduling, you must first set up the TV Guide On Screen

not be available unless the TV Guide On Screen fully operational. See the separate TV Guide On

Screen

™

Interactive Program Guide for details on

setting up the TV Guide On Screen

If you experience any issues with e-mail scheduling, please contact the following:

• In the U.S., call TACP Consumer Solutions at

1-800-631-3811 or visit

customersupport/contact.asp.

• In Canada, call TCL Customer Service at

1-800-268-3404 or visit http://www.toshiba.ca.

For home network troubleshooting tips, see Chapter 8.

™

system. E-mail scheduling will

™

system.

system is

http://www.tacp.com/

Description of fields in the “E-mail Scheduling Setup” window

For instructions on entering data in these fields, see step 5 under “Setting up e-mail scheduling” (- page 76).

E-mail Scheduling Setup

E-mail Scheduling

Check for New Mail

ID Required

Authorized E-mail

E-mail Account Setup

Cancel

E-mail Scheduling

You can select On or Off for the E-mail Scheduling field. – When this field is set to On, the TV will be able to receive

e-mails from any PC to remotely schedule and modify

recordings and reminders. – When this field is set to Off, the TV will not be able to

receive any e-mail, the other fields in this window will be

disabled (“grayed out”), and it will not be possible to

remotely schedule recordings or reminders via e-mail.

Note: This does not affect the personal e-mail feature.

Check for New Mail

This field controls the frequency of checking e-mail. Options are 5 min, 15 min, 30 min, and 1 hour.

ID Required

You can select Yes or No for the ID Required field. – When this field is set to Yes (recommended), the ID you

entered in the “ID” field must be included in all e-mails you

send to the TV. This is a security feature to protect your TV

from unauthorized e-mail access. – When this field is set to No, you do not need to include the

ID in e-mails you send to the TV.

Every 5 minutes

Yes

Done

Use the software keyboard to enter front six to 16 numbers and/or letters to create your ID (spaces and punctuation are

not

allowed).

Note:

• To help protect your privacy, you may want to choose an ID

that is different from any of your usual passwords or security

PINs (e.g., different from your personal e-mail password,

banking login code, social security number, etc.).

• The ID is case sensitive.

Authorized E-mail

If you enter an e-mail address (such as your personal e-mail address in this field, the TV will only be able to receive e-mail from this e-mail address.

Chapter 7: Using the THINC™ home network feature

Description of fields in the “E-mail Account Setup” window

E-mail Account Setup

E-mail Address mymail@isp.com

POP3 Server Address

POP3 Port Number

POP3 User Name

POP3 Password ******

SMTP Server Address

SMTP Port Number

SMTP Authentication

SMTP User Name

SMTP Password

Test Done

E-mail Address

Use the software keyboard to enter the e-mail address. (For the Personal E-mail Setup, enter your personal e-mail address. For the E-mail Scheduling Setup, enter the TV's dedicated e-mail address, which is different from your personal e-mail address.)

POP3 Server Address

Use the software keyboard to enter the POP3 server address that hosts the e-mail account.

Note: The TV does not support encrypted e-mail.

POP3 Port Number

Use the software keyboard to enter the port number used by the user’s POP3 (incoming mail) server. This field is set to 110 by default.

POP3 User Name

Use the software keyboard to enter the e-mail account login. Depending on your ISP, this may be the entire e-mail address or just the characters in the e-mail address before the “@” sign.

pop.isp.com

110

user_name

smtp.isp.com

Same as POP3

user_name

******

Cancel

SMTP Port Number

Denotes the port number used by the user’s SMTP (outgoing mail) server. This is set to 25 by default. Some ISPs block this port to prevent mail relay attacks and specify an alternate port.

SMTP Authentication

This field controls the SMTP authentication feature, and is set to Not required by default. Setting this to “Same as POP3” fills the SMTP Username and SMTP Password fields with the data filled in the “POP3 User Name” and “POP3 Password” fields. Select “Different from POP3” if the username and password for your outgoing (SMTP) mail server are different from your incoming (POP3) mail server.

SMTP User Name

This field contains the user name required by the SMTP (outgoing e-mail) server. This is typically the same as the “POP3 User Name” field, but may be different depending on the ISP/SMTP server used. This field is enabled only if the SMTP Authentication field described above is set to “Different from POP3.”

SMTP Password

This field contains the password required by the SMTP server. This is typically the same as the “POP3 Password” field used to receive e-mails, but may be different depending on the ISP/ SMTP server used. This field is enabled only if the SMTP Authentication field (described above) is set to “Different from POP3.”

Note: E-mail providers use several techniques for SMTP authentication. Only the most commonly used techniques (Network address-based, “POP before SMTP,” and “AUTH LOGIN”) are provided for your TV e-mail scheduler. SSL and TLS are currently not supported.

For home network troubleshooting tips, see Chapter 8.

POP3 Password

Use the software keyboard to enter the password for the e-mail account.

Note: To help protect your other personal Internet or e-mail accounts, create a password that is significantly different from any of your usual passwords and security PINs (e.g., different from your e-mail password, banking log-ons, social security code, etc.).

SMTP Server Address

Use the software keyboard to enter the SMTP mail server associated with the e-mail account. (The TV will use this server for sending reply e-mails to your personal e-mail account.)

Chapter 7: Using the THINC™ home network feature

I. Using e-mail scheduling

You can use the e-mail scheduling feature to schedule and delete recordings and reminders by sending a “request e-mail” to the TV’s e-mail address from any PC.

The four commands the TV will accept are ADD, DELETE, GET, and HELP, as described in this section.

If you have not already done so, follow the instructions in sections A and B (- pages 60–61), and in section H (- page

75), before proceeding. When a recording is scheduled via e-mail, the recording device

used will be the VCR connected to the TV’s analog A/V OUT terminals (see item 4 on page 9 for the location of the A/V OUT terminals; see the separate Installation Guide for various VCR connection examples).

E-mail parameters

Note: Some e-mail clients automatically insert e-mail signatures, which the TV will try to process. These may generate unwanted error messages.

The maximum allowable size for an e-mail sent to the TV is

•

16 KB. E-mails over 16 KB will be automatically deleted.

• E-mails sent to the TV cannot contain any attachments. The

TV will automatically delete any e-mail with an attached file.

• E-mails can be formatted either Plain Text or Rich Text

Format (HTML style).

• E-mails sent to the TV that are not properly formatted, that

are from the wrong e-mail address, or that have the wrong ID (if specified) will be deleted.

• All e-mails sent to the TV will be eventually deleted.

Note:

• Toshiba is not responsible for any damage or loss caused directly or indirectly by the failure of the e-mail scheduling feature to record content intended to be recorded.

• Toshiba is not responsible for, nor has any control over, any content recorded and/or viewed using the e-mail scheduling feature. Further, the e-mail scheduling feature is not meant to be used for unauthorized recording and/or viewing of copyrighted works.

• The unauthorized recording, use, distribution, or revision of television programs, videotapes, DVDs, and other materials is prohibited under the Copyright Laws of the United States and other countries, and may subject you to civil and criminal liability.

Sending a request e-mail to the TV

To send a request e-mail to the TV:

1 Format the e-mail according to the instructions under

“Formatting a request e-mail” on the next page.

2 Send the e-mail to the TV. 3 After the TV receives and processes the e-mail, the TV

will send a reply e-mail indicating whether the e-mailed request succeeded or failed. See “Receiving an e-mail from the TV” (- page 81).

Chapter 7: Using the THINC™ home network feature

Formatting a request e-mail

Recognized tags

When you send an ADD, DELETE, GET, or HELP request e-mail to the TV, the TV will recognize only the tags listed below. These tags (and their accompanying data) must be listed in the body of the request e-mail in the following order:

• ID [your ID*]

(not required if you set the “ID Required” field to No)

• COMMAND ADD

(or COMMAND DELETE or COMMAND GET or COMMAND HELP)

• INPUT [name of input to record]

• CHANNEL [channel number of recording or reminder]

• DATE [date of recording or reminder]

• START TIME [start time of recording or reminder]

• DURATION [length of recording or reminder]

• TYPE RECORD

(or TYPE REMIND)

Tag and data formats

The data for each tag can be formatted in various ways, as described in the following table:

Tag formats Data formats

ID*

COMMAND (or CMD)

INPUT (or INP)

CHANNEL (or CH)

DATE

START TIME (

START)

DURATION (or DUR)

TYPE

[6- to 16-character alphanumeric] MYID1234* (example only)

ADD DELETE (or DEL) GET HELP

ANT1 (or ANT-1) ANT2 (or ANT-2) CABLEBOX (or CB) SETTOPBOX (or STB)**

5 … 38 … 100 … 5-1 … 120-1

[Use a hyphen for digital channels]

7-4 (or 7-4-06 or 7-4-2006 or 7/4/06, etc.)

[If the year is not specified, the current year is assumed.]

8AM ... 9:30PM

[Noon = 12PM; Midnight = 12AM]

30M (or 30MIN) 2H30M (or 2HR30MIN or 2:30)

RECORD (or REC) REMIND (or REM)

Sample request e-mails

• The examples shown below are for illustration purposes

only.

• Styles applied to the sample e-mail text (such as bold, italic,

and underline) are for illustration purposes only. You do not need to style the text in your request e-mails.

• The only text in a request e-mail that is case sensitive is the

ID. All other text is not case sensitive.

ADD request e-mail

The ADD request allows you to schedule a new recording or reminder.

The required tags for an ADD request e-mail are (in this order):

• ID [your ID*]

(not required if you set the “ID Required” field to No)

• COMMAND ADD

• INPUT [name of input]

• CHANNEL [channel number of recording or reminder]

• DATE [date of recording or reminder]

• START TIME [start time of recording or reminder]

• DURATION [length of recording or reminder]

• TYPE RECORD ...or... TYPE REMIND

Sample

ADD

request e-mail

to schedule a new

To: [TV’s e-mail address [Subject can be left blank]

ID MYID1234*

COMMAND ADD INPUT ANT-1 CHANNEL 102-1 DATE 06/10/2006 START TIME 7 PM DURATION 2H15M TYPE RECORD

recording:

]

GET request e-mail

When you send a GET request e-mail to the TV, you will receive a reply e-mail that lists all currently scheduled recordings and/or reminders.

The only required tag and data for a GET request e-mail is GET.

Sample GET request e-mail:

To: [TV’s e-mail address] [Subject can be left blank]

GET

Sample ADD request e-mail to schedule a new reminder:

To: [TV’s e-mail address] [Subject can be left blank]

ID MYID1234*

cmd add input cb ch 4 date 7-4 start 8:30pm dur 1hr type remind

* The ID is case sensitive. The ID tag is required only if you created

an ID in the “ID” field and set the “ID Required” field to Yes. If you set the “ID Required” field to No, you do not need to include the ID tag line in your request e-mail. See “Description of fields in the E-mail Scheduling Setup window” (- page 77).

**“Set-top box” and “STB” refer to a satellite set-top box.

Chapter 7: Using the THINC™ home network feature

DELETE request e-mail

The DELETE request allows you to cancel a scheduled recording or reminder.

The required tags for a DELETE request e-mail are (in this order):

• ID [your ID*]

(not required if you set the “ID Required” field to No)

• COMMAND DELETE

• INPUT [name of input]

• CHANNEL [channel number of recording or reminder]

• DATE [date of recording or reminder]

• START TIME [start time of recording or reminder]

• DURATION [length of recording or reminder]

• TYPE RECORD ...or... TYPE REMIND

Sample DELETE request e-mail to delete an existing recording:

To: [TV’s e-mail address] [Subject can be left blank]

ID MYID1234*

COMMAND DELETE INPUT ANT-1 CHANNEL 102-1 DATE 06/10/2006 START TIME 7 PM DURATION 2H15M TYPE REC

Sample DELETE request e-mail to delete an existing reminder:

To: [TV’s e-mail address] [Subject can be left blank]

ID MYID1234*

cmd del input cb ch 4 date 7-4 start 8:30pm dur 1hr type rem

HELP request e-mail

When you send a HELP request e-mail to the TV, you will receive a reply e-mail that contains helpful information about formatting a request e-mail (syntax, definition of the various commands, etc.).

The only required tag for a HELP request e-mail is HELP.

Sample HELP request e-mail:

To: [TV’s e-mail address] [Subject can be left blank]

HELP

* The ID is case sensitive.

The ID tag is required only if you created an ID in the “ID” field and set the “ID Required” field to Yes. If you set the “ID Required” field to No, you do not need to include the ID tag line in your request e-mail. See “Description of fields in the E-mail Scheduling Setup window” (- page 77).

Receiving an e-mail from the TV

If the request e-mail was successful, the reply e-mail from the TV to your PC will contain one of the following (or similar) messages, depending on the command you sent to the TV:

• ADD SUCCESS

• DELETE SUCCESS

• GET SUCCESS

• HELP SUCCESS

If the request e-mail was not successful, the reply e-mail from the TV to your PC will contain one of the following (or similar) messages, depending on the command you sent to the TV:

• FAILED – SCHEDULE CONFLICT.

The new recording or reminder you attempted to schedule conflicts with an existing one that was previously scheduled.

If you want to schedule the new recording or reminder, you will have to DELETE the existing one first, and then ADD the new one.

• FAILED – COULD NOT UNDERSTAND “Line x.”

The request e-mail has an error in the line of text referenced in the error message. Correct the text and resend the e-mail.

• FAILED – NO DEVICE AVAILABLE.

Make sure you have a recording device connected to the TV and that all cables are properly connected, and then resend the e-mail.

• FAILED – MISC ERROR.

Make sure all devices and cables are properly connected and that the text in the body of your e-mail is correct, and then send the corrected e-mail to the TV.

Modifying an existing recording or reminder

To modify an existing scheduled recording or reminder:

1 Send a DELETE request e-mail to cancel the existing

recording or reminder.

2 Send an ADD request e-mail to schedule the modified

recording or reminder.

For home network troubleshooting tips, see Chapter 8.

Chapter 8: Troubleshooting

General troubleshooting

Before calling a service technician, please check this chapter for a possible cause of the problem and some solutions you can try.

Black box on screen

• The Closed Caption feature is set to one of the Text

modes (T1, T2, T3, or T4). Set the Closed Caption feature to Off (- page 42).

LED indications while in reboot from standby

• When you plug the power cord in the red LED will blink

until the TV enters standby mode (plugged in but not powered on). This is normal and is not a sign of malfunction.

TV stops responding to controls

• If the TV stops responding to the controls on the remote

control or TV control panel and you cannot turn off the TV, press and hold the POWER button on the TV control panel for 5 or more seconds to reset the TV.

Toshiba 42LZ196, 47LZ196 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual