This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken to obtain the best results and for safety to be assured. Please read the points below for your own
safety. They are of a general nature, intended to help with all electronic consumer products and some points may not apply
to the goods you have just purchased.
English
Air Circulation
Leave more than 10cm clearance around the television to
allow adequate ventilation. This will prevent overheating
and possible damage to the television. Dusty places should
also be avoided.
Heat Damage
Damage may occur if the television is left in direct sunlight
or near a heater. Avoid places subject to extremely high
temperatures or humidity, or locations where the temperature
is likely to fall below 5°C (41°F).
Mains Supply
The set should be operated only from a 220-240 V AC 50 Hz
outlet. DO ensure that the television is not standing on the
mains lead. DO NOT cut off the mains plug from this equipment, this incorporates a special Radio Interference Filter, the
removal of which will impair its performance. It should only be
replaced by a correctly rated and approved type and the fuse
cover must be refi tted. IF IN DOUBT PLEASE CONSULT A
COMPETENT ELECTRICIAN.
Warning
To prevent the spread of fi re, keep candles or other open
fl ames away from this product at all times.
Do
DO read the operating instructions before you attempt to
use the equipment.
DO ensure that all electrical connections (including the mains
plug, extension leads and inter connections between pieces
of equipment) are properly made and in accordance with the
manufacturers’ instructions. Switch off and withdraw the mains
plug before making or changing connections.
DO consult your dealer if you are ever in doubt about the
installation, operation or safety of your equipment.
DO be careful with glass panels or doors on equipment.
Do not
DON’T remove any fi xed cover as this may expose danger-
ous voltages.
DON’T obstruct the ventilation openings of the equipment
with items such as newspapers, tablecloths, curtains, etc.
Overheating will cause damage and shorten the life of the
equipment.
DON’T allow electrical equipment to be exposed to dripping
or splashing or objects fi lled with liquids, such as vases, to
be placed on the equipment.
DON’T place hot objects or naked fl ame sources, such as
lighted candles or nightlights on, or close to equipment. High
temperatures can melt plastic and lead to fi res.
DON’T use makeshift stands and NEVER fi x legs with wood
screws. To ensure complete safety, always fi t the manufactur-
ers’ approved stand, bracket or legs with the fi xings provided
according to the instructions.
DON’T leave equipment switched on when it is unattended,
unless it is specifi cally stated that it is designed for unat-
tended operation or has a standby mode. Switch off by
withdrawing the plug, make sure your family know how to do
this. Special arrangements may need to be made for people
with disabilities.
DON’T continue to operate the equipment if you are in any
doubt about it working normally, or it is damaged in any way switch off, withdraw the mains plug and consult your dealer.
WARNING - excessive sound pressure from earphones or
headphones can cause hearing loss.
ABOVE ALL - NEVER let anyone, especially children,
push or hit the screen, push anything into holes, slots
or any other openings in the case.
NEVER guess or take chances with electrical equipment
of any kind - it is better to be safe than sorry.
THE MAINS PLUG IS USED AS A DISCONNECTING
DEVICE AND THEREFORE SHOULD BE READILY OPERABLE.
Note : Interactive video games that involve shooting
a “gun” type of joystick at the on-screen target may
not work with this TV.
Locate the television away from direct sunlight and strong
lights. Soft, indirect lighting is recommended for comfortable
viewing. Use curtains or blinds to prevent direct sunlight
falling on the screen.
Place the TV on a stable, level surface that can support the
weight of the TV.
it falling over, secure the TV to a wall using a sturdy tie to
the clip on TV. Install the P clip under the stand as shown in
the above illustration.
The LCD display panels are manufactured using an extremely high level of precision technology; however, sometimes
The digital reception function of this television is only effective in the countries listed in the “Country” section
during the fi rst time installation menu. Depending on country/area, some of this television’s functions may not
be available. Reception of future additional or modifi ed services can not be guaranteed with this television.
If stationary images generated by 4:3 broadcasts, text services, channel identifi cation logos, computer displays,
video games, on screen menus, etc. are left on the television screen for any length of time, they could become
conspicuous. It is always advisable to reduce both the brightness and contrast settings.
Very long, continuous use of the 4:3 picture on a 16:9 screen may result in some retention of the image at
the 4:3 outlines. This is not a defect of the LCD TV and is not covered under the manufacturer’s warranty.
Regular use of other size modes will prevent permanent retention.
Toshiba shall under no circumstances be liable for loss and/or damage to the product caused by:
i) fi re;
ii) earthquake;
iii) accidental damage;
iv) intentional misuse of the product;
v) use of the product in improper conditions;
vi) loss and/or damage caused to the product whilst in the possession of a third party;
vii) any damage or loss caused as a result of the owner’s failure and/or neglect to follow the instructions set out in the
owner’s manual;
viii) any loss or damage caused directly as a result of misuse or malfunction of the product when used simultaneously with
associated equipment;
Furthermore, under no circumstances shall Toshiba be liable for any consequential loss and/or damage including but not
limited to the following, loss of profi t, interruption of business, the loss of recorded data whether caused during normal opera-
tion or misuse of the product.
Note: A Toshiba wall bracket or stand, where available, must be used.
In order to maintain stability and prevent
Where to install
Sturdy tie
(as short
as possible)
P Clip
P Clip
“P” Clip position on TV is dependent on model.
some parts of the screen may be missing picture elements or
have luminous spots. This is not a sign of a malfunction.
Make sure the television is located in a position where it cannot
be pushed or hit by objects, as pressure will break or damage
the screen. Also, please be certain that small items cannot be
inserted into slots or openings in the case.
Cleaning the screen and cabinet…
Turn off the power, and clean the screen and cabinet with a
soft, dry cloth. We recommend that you do not use any proprietary polishes or solvents on the screen or cabinet as this
may cause damage.
WHEN THIS UNIT IS PLUGGED INTO THE WALL OUTLET, DO NOT PLACE YOUR EYES CLOSE TO
THE OPENINGS TO LOOK INTO THE INSIDE OF THIS UNIT.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED
PERSONNEL.
Headphone Warning
Loud music can damage your hearing irreversibly. Do not set the volume to a high level when listening through
headphones, particularly for extended listening periods.
Information for the DVB-T function
• Any function relative to the digital television (with the DVB logo) is available only within the country or area
where such signals are transmitted. Verify with the salesperson if it is possible to receive a DVB-T signal in
the zone where you live.
• Even if the television conforms to the DVB-T specifi cations, the compatibility to future digital DVB-T
transmissions is not guaranteed.
• Some digital television functions may not be available in some countries.
• The DVB-T system present in this device is FTA (Free to air).
• DVB is a registered trademark of the DVB Project. This logo indicates that the product is compliant with
European Digital Broadcasting.
Possible Adverse Effects on LCD Screen
If a fi xed (non-moving) pattern remains on the LCD screen for long periods of time, the image can become
permanently retained on the LCD TV panel and cause subtle but permanent ghost images. This type of
damage is NOT COVERED BY YOUR WARRANTY. Never leave your TV on for long periods of time while it
is displaying the following formats or images:
• Fixed Images, such as stock tickers, video game patterns, TV station logos, and websites.
• Special Formats that do not use the entire screen. For example, viewing letterbox style (16:9) media on
a normal (4:3) display (Black bars at top and bottom of screen); or viewing normal style (4:3) media on a
widescreen (16:9) display (Black bars on left and right sides of screen).
English
IMPORTANT INFORMATION
TV Installation
If a television is not positioned in a suffi ciently stable location, it can be potentially hazardous due to falling.
Many injuries, particularly to children, can be avoided by taking simple precautions such as:
• Using stands recommended by the manufacturer of the television.
• Only using furniture that can safely support the television.
• Ensuring the television is not overhanging the edge of the supporting furniture.
• Not placing the television on tall furniture (for example, cupboards or bookcases) without anchoring both the
furniture and the television to a suitable support.
• Not standing the
furniture.
• Educating children about the dangers of climbing on furniture to reach the television or its controls.
Place the TV on a stable, level surface that can support the weight of the TV. In order to maintain stability
and prevent it from falling over, secure the TV to a wall using a sturdy tie to the clip on the back of the table
top stand.
This unit has been produced according to all current safety regulations. The following safety tips should safeguard users
against careless use and the dangers related to such use.
• Although this unit has been carefully manufactured and rigorously checked prior to leaving the factory as with all electrical
appliances, it is possible for problems to develop. If you notice smoke, an excessive build-up of heat or any other unexpected
phenomena, you should disconnect the plug from the mains power socket immediately.
television on cloth or other materials placed between the television and supporting
English - 5 -
Important safety information (continued)
• Ensure that the unit is suffi ciently ventilated! Never place it
English
next to or underneath curtains!
• This set should only be connected to
mains power supply. Do not attempt to connect it to any other
type of supply.
• The socket outlet must be installed near the equipment and
is easily accessible.
• Do not open this unit. An attempt to repair the unit by a
non-expert could be dangerous and potentially cause a fi re
hazard. All repairs must be carried out by qualifi ed service
personnel only.
• Keep away from rodents. Rodents (and also cockatiels)
enjoy biting electric fl exes. They can cause a short circuit
(fi re hazard!) and receive a fatal electric shock.
• Always hold the plug when disconnecting the unit from
the socket outlet. Do not pull on fl ex. The fl ex can become
overloaded and cause a short circuit.
• Use
a soft, dry cloth to clean the unit.
• Set up unit so that no one will trip over the fl ex.
• This unit is recommended to be installed on shock-free
benches in order to avoid any danger from falling.
• Take note that toddlers can pull the unit down from a table or
cupboard by means of its fl ex. Children can hurt themselves
when doing this.
• Do not use the unit near heat sources. The casing and fl ex
could be damaged by the intensity of the heat.
• The screen is made of glass and can break if damage is done
to it. Be careful when collecting sharp edged glass splitters.
• If you intend to wall mount the unit, contact the shop where
you purchased the unit for advice, and leave the installation
work to professionals. Improper installation can cause
damage and/or injuries.
• When installing the set on a wall, allow at least 10 cm
clearance between the rear of the set and the wall. Clearance
of less than 10 cm will obstruct the vents and cause
overheating to the interior of the set, resulting in faults or
damage to the set.
• Taking fall-prevention measures
- If these measures are not taken, the unit can fall and cause
damage and/or injuries.
- Contact the shop where you purchased the unit to obtain
full details of the measures.
• When a TV stand is used,
- Ensure the unit is fully on the stand and placed in the
centre.
- Do not leave the stand doors open. You could be hurt as
a result of the unit falling or breaking, or your fi ngers being
caught or jammed. Take extra precautions if you have
children.
• Avoid placing the unit on any surfaces that may be subject
to vibrations or shocks.
• To protect the unit during a thunder storm, unplug the AC
power cord and disconnect the aerial.
Caution: Do not touch the aerial connector.
• When you leave your home for a long period of time, unplug
the AC power cord for safety.
a 220-240V AC 50Hz
• The unit becomes warm when in operation. Do not place
any covers or blankets on the unit in order to prevent
overheating.
The ventilation holes should not be blocked. Do not set up
near radiators. Do not place in direct sunshine.
• When placing on a shelf, allow at least 10 cm clearance
space around the whole unit.
• The unit shall not be exposed to dripping or splashing, and
no objects fi lled with liquids, such as vases, shall be placed
on the apparatus.
• Liquids spilled into the unit can cause serious damage.
Switch the set off and disconnect the mains power supply,
then consult a qualifi ed service person before attempting to
use the unit again.
• Moisture condensation occurs, for example, when you pour
a cold drink into a glass on a warm day and drops of water
form on the outside of the glass. In the same way, moisture
may condense on this unit’s internal optical pick-up lens, one
of the most crucial internal parts of the unit.
• Moisture condensation occurs in the following situations:
- When you move the unit from a cold place to a warm
place.
- When you use the unit in a room where the heater was
just turned on.
- When you use the unit in an area where cold air from an air
conditioner directly hits the unit.
- When you use the unit in a humid place.
• Never use the unit when moisture condensation may
occur.
• Using the unit when moisture condensation exists may
damage its own internal parts and discs. Connect the power
cord of the unit to the wall outlet, turn on the unit, remove the
disc, and leave it for two or three hours. After two or three
hours, the unit will warm up and moisture will be evaporated.
Leaving the TV connected to the wall outlet will help prevent
moisture condensation in the unit.
• Never place hot objects or open fl ame sources, such as
lighted candles or night lights, on or close to the TV. High
temperatures can melt plastic and lead to fi res.
If you decide to wall mount your LCD TV, always use a wall bracket appropriate for the size and weight of
the LCD TV:
(1) Caution: Two people are required for installation.
(2) Unplug and remove any cables and/or other component connectors from the rear of the TV.
(3) Follow the instructions provided with your wall bracket. Before proceeding, make sure the appropriate
bracket(s) are attached to the wall and the back of the TV as described in the instructions provided with the
wall bracket.
(4) IMPORTANT: Always use the screws supplied or recommended by the wall mount manufacturer.
(5) After attaching the appropriate bracket(s) to the wall and the back of the TV, remove the pedestal stand
from the TV as described
Removing the pedestal stand
(1) Carefully lay the front of the TV face down on a fl at, cushioned surface such as a quilt or blanket. Leave
the stand protruding over the edge of the surface.
Note: Extreme care should always be taken when removing the pedestal stand to avoid damage to
the LCD panel.
(2) Remove the
(3) Once you have removed
the TV by removing away from the TV.
four screws on the stand. This will allow removal of the pedestal stand.
below.
four screws holding the pedestal stand in place, remove the pedestal stand from
Simple at-a-glance reference of your remote control.
Standby/ On mode
Freeze Picture
Mono-Stereo / Dual I-II
To select TV
programme number
Audio description
Programme guide
Quick Settings
Navigation Buttons
Exit
menu
To change channels
Hold Page (in TXT mode)
Teletext Controls
Operation LED
Switch to TV or DVD mode
Subtitle on/off
Teletext
Analogue/Digital broadcasts
AV / Source
MENU On/Off
OK / Confirm
Return to previous menu
Info
To alter the volume
Reveal (in TXT mode)
To mute the sound
Note: Buttons that are not indicated
on the remote control illustration are
not functional in TV mode.
Inserting Batteries and Effective Range of the Remote Control
Remove the back cover to reveal the battery compartment and make sure
the batteries are inserted the right way round. Suitable battery types for this
remote are AAA, IEC R03 1.5V.
Do not combine a used, old battery with a new one or mix battery types.
Remove dead batteries immediately to prevent acid from leaking into the
battery compartment. Dispose of them in a designated disposal area.
Warning: Batteries must not be exposed to excessive heat such as sunshine,
fi re or the like.
The performance of the remote control will deteriorate beyond a distance of
fi ve metres or outside an angle of 30 degrees from the centre of the television.
If the operating range becomes reduced the batteries may need replacing.
If you use a decoder* or a media recorder, it is essential
that the scart cable is connected to the TV.
Before running fi rst time installation, any connected devices
need to be set to standby
mode.
The DIGITAL AUDIO socket enables the connection of a
SCART
Socket
A wide variety of external equipment can be connected to the
TV; therefore, the relevant owner’s manuals for all additional
equipment must be referred to for exact instructions.
If the TV automatically switches over to monitor external
equipment, return to normal TV by pressing the desired programme position button. To recall external equipment, press
button repeatedly to switch between sources.
Regardless of source’s property, audio output from the DIGITAL AUDIO socket cannot be copied.
suitable surround sound system.
®
HDMI
(High-Defi nition Multimedia Interface) is for using
with a DVD decoder or other equipment with digital audio and
video output. It is designed for best performance with 1080i
and 1080p high-defi nition video signals but will also accept
and display VGA, 480i, 480p, 576i, 576p and 720p signals.
PC format signals will also be displayed.
NOTE: Although this TV is able to connect to HDMI equipment,
it is possible that some equipment may not operate correctly.
Connecting an HDMI® or DVI Device to the HDMI Input
English
The HDMI input on your TV receives digital audio and
uncompressed digital video from an HDMI source device
or uncompressed digital video from a DVI (Digital Visual
Interface) source device.
This input is designed to accept HDCP (High-Bandwidth
Digital-Content Protection) programme material in digital
form from EIA/CEA-861-D–compliant [1] consumer electronic
devices (such as a set-top box or DVD player with HDMI or
DVI output).
NOTE:
• Some early HDMI equipment may not work properly with
your latest HDMI TV.
• Supported Audio format: Linear PCM, sampling rate
32/44.1/48kHz.
To Connect an HDMI Device
Connect an HDMI cable (type A connector) to the HDMI terminal. For proper operation, it is recommended that you use
an HDMI cable with the HDMI Logo ().
• If your HDMI connection is capable of 1080p and/or
your TV is capable of refresh rates greater than 50Hz, you
will need a Category 2 cable. Conventional HDMI/DVI cable
may not work properly with this mode.
• HDMI cable transfers both video and audio. Separate
analogue audio cables are not required (see illustration).
• To view the HDMI device video, press
HDMI1 or HDMI2.
button to select
To Connect a DVI Device
Connect an HDMI-to-DVI adaptor cable (HDMI type A connector) to the HDMI input socket and audio cables to the SIDE AV
socket, using the supplied Side AV connection cable’s RED
and WHITE inputs (see illustration).
• The recommended HDMI-to-DVI adaptor cable length is
6.6 ft (2m).
An HDMI-to-DVI adaptor cable transfers video only. •
Separate analogue audio cables are required.
SIDE AV Input
SIDE AV
Side Audio/Video
Connection Cable
(Supplied)
HDMI Input
Sockets
Audio Cable
(Not supplied)
HDMI to DVI
Adapter Cable
(not supplied)
NOTE:
To ensure that the HDMI or DVI device is reset properly, it is
HDMI Input
Sockets
(Back)
recommended that you follow these procedures:
• When turning on your electronic components, turn on the
TV fi rst, and then the HDMI or DVI device.
• When turning off your electronic components, turn off the
HDMI or DVI device fi rst, and then the TV.
With either an RGB/PC or an HDMI connection, you can watch
your computer’s display on the TV and hear the sound from
the TV’s speakers.
When connecting a PC to the RGB/PC input on TV, use
an analogue RGB (15-pin) computer cable and use the SIDE
AV socket with a PC audio cable (not supplied) for audio
connection, using the supplied Side AV connection cable’s
RED and WHITE inputs (see illustration).
PC VGA Cable
(Not supplied)
RGB/PC Input
(back)
SIDE AV Input
SIDE AV
Side Audio/Video
Connection Cable
(Supplied)
PC Audio Cable
(Not supplied)
To use a PC, set the monitor output resolution on the PC
before connecting it to the TV. To display the optimum picture,
use the PC setting feature.
NOTE:
Some PC models cannot be connected to this TV. •
An adaptor is not needed for computers with a
compatible mini D-sub15-pin terminal.
Depending on the DVD’s title and the specifi cations •
of the PC on which you are playing the DVD-Video,
some scenes may be skipped or you may not be
able to pause during multiangle scenes.
Or
Connecting to a DVD Player via YPbPr
Some DVD players are connected through
COMPONENT SOCKETS (YPbPr). In this case,
you must use the supplied Component YPbPr video
connection cable for enabling connection. First, plug
the single jack of the cable to the TV’s YPbPr socket
(side). Afterwards, insert your YPbPr cable’s (not
supplied) connectors into the plural part of the supplied
YPbPr video connection cable (see illustration below).
Colours of the connected jacks should match.
To enable audio connection, use the supplied Side AV
connection cable. First, plug single jack of the cable
to the Side AV Input of the TV. Afterwards, insert your
DVD player’s audio cable’s connectors into the plural
part of the supplied Side AV connection cable (see
illustration below). Colours of the connected jacks
should match.
You can connect a USB memory to your TV by using •
the USB input of the TV. This feature allows you to
display/play music, photo or video fi les stored in a
USB memory.
It is possible that certain types of USB devices (e.g. •
MP3 Players) may not be compatible with this TV.
You may back up your fi les before making any •
connections to the TV set in order to avoid any
possible data loss. Note that manufacturer will not
be responsible for any fi le damage or data loss.
Do not pull out USB memory while playing a fi le.•
CAUTION: Quickly plugging and unplugging USB
devices, is a very hazardous operation. Especially,
do not repeatedly quickly plug and unplug the drive.
This may cause physical damage to the USB player
and especially the USB device itself.
USB Memory Connection
Plug your USB memory to the USB input of the •
TV.
This television is designed to consume less energy to save environment. •
You not only help to save the environment but also can save money by reducing electricity bills, thanks to the •
energy effi ciency feature of this TV. To reduce energy consumption, you should take the following steps:
You can use Power Save Mode setting, located on page 31. If you set Power Save Mode as On, the TV will •
switch to energy-saving mode and luminance level of TV set will be decreased to optimum level. Note that
some picture settings will be unavailable to be changed when the TV is in Power Save Mode.
When the TV is not in use, please switch off or disconnect the TV from the mains plug. This will also reduce •
energy consumption.
Disconnect power when going away for longer time.•
Note that annually, using the TV set in Power Save Mode has more power effi ciency than disconnecting •
the TV from the mains plug instead of keeping stand-by mode. Therefore it is highly recommended to
activate Power Save Mode setting to reduce your annual power consumption. And also it is recommended
to disconnect the TV from the mains plug to save energy more when you do not use.
Please helps us to save environment by following these steps.•
This television is designed to consume less energy.•
Harmful substances and contents that are dangerous to health, are eliminated in its design.•
This product is designed to endure longer and it is subject to recycling at the end of its service life.•
When the TV reaches the end of its service life, dispose the product in accordance with the proper recycling •
process as explained on page 41.
Repair Information
Please refer all servicing to qualifi ed personnel. Only qualifi ed personnel must repair the TV. Please contact
your local dealer, where you have purchased this TV fo
A wide variety of external equipment can be connected via the sockets located on the side and back of the
TV. Whilst all the necessary adjustments and controls for the TV are made using the remote control, the
buttons on the left side of the TV may be used for some functions.
USB
5Vdc
Max:500mA
Remote Control Sensor
+/- control/volume buttons
Programme / Volume / AV Function
Standby / On button
YPbPr
SIDE AV
Standby LED
Switching on
If the standby LED is unlit, check that the mains plug is connected to the power and press
the TV to switch the television on. Then the LED lights up in
green. If the picture does not appear, press
remote control; it may take a few moments.
To put the television into Standby, press
remote control. To view the television, press
The picture may take a few seconds to appear.
Note: The active Standby LED may appear for a few moments
when the TV is switched off.
button on the left side of
button on the
button on the
button again.
For energy saving:
Turning the TV off at its mains supply, or un-plugging it, will
cut energy use to nearly zero for all TV’s. This is recommended when the TV is not being used for a long time, e.g.
when on holiday.
Reducing the brightness of the screen will reduce energy use.
Energy effi ciency cuts energy consumption and thus saves
money by reducing electricity bills.
NOTE: Putting the TV into standby mode, will reduce energy
consumption, but will still draw some power.
Using the Remote Control
Press MENU button on the remote control to see the
menus.
The main menu appears as a group of icons each for a
menu option. Press Left or Right button to select a topic,
and press OK button.
In sub menu screen mode the menu appears as a list. Press
Up or Down button to select a topic, and press OK button.
To use the options press Up or Down button on the remote
control to move up and down through them and OK button, Left or Right button to select the required choice. Follow
the on screen instructions. The functions of each menu are
described in the manual.
Using the Controls and Connections on the TV
Using the control buttons on the side of the TV:
To alter the volume press orbutton. If the volume
•
does not change, press
orbutton again.
• To alter the programme position press button once
and then
press or button.
• To select an external input, press and hold
until “Sources list” is displayed. To select an external input,
press button repeatedly until the appropriate input
source is selected.
NOTE: The USB socket has limited functionality, and Toshiba
can take no responsibility for damage to other connected
equipment.
Please always refer to the owner’s manual of the equipment
to be connected for full details.
Before switching on the TV, put your decoder and media recorder to Standby if they are connected and
ensure the aerial is connected to your TV. To set up the TV, use the buttons on the remote control as
IMPORTANT: Ensure that the aerial or cable is
connected and a Common Interface module is not
inserted before switching on the TV for the fi rst time
installation.
Connect the mains plug and switch the TV1. to on
using the side standby switch. If the TV does not
switch on, press any numbered or
the remote control, then the language selection
menu will be displayed.
the fi rst time that the TV is switched on and each
time the TV is reset.
By pressing 2. Up or Down button, highlight the
language you want to set and press OK button.
The following message will be displayed next:
This screen will appear
detailed on page 8.
button on
Select 6. Yes button by using Left or Right button
and press OK button to continue. Afterwards, the
following OSD will be displayed on the screen:
If you select 7. Cable option, the following screen
will be displayed:
English
You can select frequency ranges from this 8.
screen. For highlighting lines you see, use Up or
Down button. You can enter the frequency range
manually by using the numeric buttons on the
remote control. Set Start and Stop Frequency as
desired by using numeric buttons on the remote
control. After this operation, you can set Search
By pressing 3. Left or Right button, select the country you want to set and press Down button
to highlight Teletext Language option. Use
Left or Right button to select desired Teletext
Language.
Press 4. Down button after setting Teletext Language
option. Scan Encrypted will be then highlighted.
You can set Scan Encrypted as Yes if you want
to scan coded stations.
Press 5. OK button on the remote control to continue
and the following message will be displayed on
the screen:
Step as 8000 kHz or 1000 kHz. If you select
1000 kHz, the TV will perform search process
in a detailed way. Searching duration will thus
increase accordingly. When fi nished, press OK
button to start automatic search.
If you select 9. Aerial option from the Search Type
screen, the television will search for broadcasts.
The Auto tuning screen will appear and the 10.
television will start to search for available stations.
The progress bar will move along the line. You
must allow the television to complete the search.
The following OSD will be displayed on the
screen and the television will search for digital
and analogue TV broadcasts:
Initial Installation - continued
English
Note: You can press MENU button to cancel.
After the available stations are stored, Channel List •
will be displayed on the screen. If you like the sort
channels, according to the LCN, please select Yes
and then press OK button (if available).
Press • OK button to quit channel list and watch TV.
Note:
Do not turn off the TV while initializing fi rst time
installation.
Auto Tuning
Auto Tuning
As new services are broadcast, it will be necessary to
retune the television in order to view them.
Auto Tuning will completely retune the television •
and can be used to update the channel list. It is
recommended that Auto Tuning is run periodically
to ensure that all new services are added. All current
channels and settings, i.e. locked channels, will
be lost.
Press • MENU button on the remote control and select Install and Retune by using Left or Right button.
Press OK button and the following menu screen
will be displayed.
Select • Automatic Channel Scan by using Up or Down button and press OK button. Automatic Channel
Scan options will be displayed. You can select Digital
Aerial, Analogue or Digital Aerial-Analogue tuning
using Up or Down and OK buttons.
Auto Channel Scan Menu Operation
Digital Aerial: Searches and stores aerial DVB stations.
Digital Cable: Searches and stores cable DVB stations.
Analogue: Searches and stores analogue stations.
Digital Aerial & Analogue: Searches and stores both
analogue and aerial DVB stations.
Digital Cable & Analogue: Searches and stores both
analogue and cable DVB stations.
Whenever you select an automatic search type and •
press OK button, a confi rmation screen will appear
on the screen. To start installation process, select
Yes, to cancel select No by using Left or Right
and OK button.
After auto channel scan type is set and selected •
and confi rmed, installation process will start and
progress bar will move along. Press MENU button
to cancel process. In such a case, located channels
are not stored. The television will start to search for
all available stations. You must allow the television
to complete the search.
The television can be tuned-in manually using Manual Search feature.
English
Digital Aerial Manual Search
The feature is available for service engineers or
can be used for direct channel entry if the multiplex
channel is known.
Select • Manual channel scan from the Install and
Retune menuand press OK.
After selecting search type as • Digital Aerial, you can
enter the multiplex or frequency number using the
numeric buttons and press OK button to search.
Enter the multiplex number using the numeric •
buttons. The television will automatically search
for that multiplex. When the multiplex is found any
channels not currently on the programme list will be
added and the programme information at the top of
the screen will be updated.
Repeat as necessary.•
Digital Cable Manual Search
In cable manual scan, you can enter frequency, •
modulation, symbol rate and network channel scan
options. After selecting search type as Digital Cable,
you can set the desired options and press OK button
to search.
Analogue Manual Search
The television can be tuned-in manually. For example:
if the television cannot be connected to a media
recorder/decoder with a SCART lead or to tune-in a
station on another System.
To allocate a programme position on the television
for a decoder and media recorder: turn the decoder
on, insert a pre-recorded fi lm into the media recorder
and press PLAY, then manually tune.
After selecting search type as Analogue, you can
use Up or Down button to highlight an item and then
press Left or Right button to set an option.
Enter the channel number or frequency using the
numeric buttons. You can then press OK button
to search. When the channel is located, any new
channels that are not on the list will be stored.
Analogue Fine Tune
Select • Analogue Fine Tune from the Install and
Retune menu by using Up or Down and OK
buttons. Analogue fi ne tune screen will be displayed.
Analogue Fine Tune feature will not be available
if there are no analogue channels, only digital
If stereo or dual language broadcasts are transmitted, the
word Stereo or Dual will appear on the screen each time positions are changed, disappearing after a few seconds. If the
broadcast is not in stereo, the word Mono will appear.
Stereo… Press
Bilingual… Bilingual transmissions are rare. If they are
transmitted, the word Dual will be displayed. Choose the
required programme number, and if the word Dual appears,
press
For DTV broadcasts
To view current language and for changing to an
alternative language (if available), press AD button.
Available options will be listed.
to select Dual 1, Dual 2 or Mono.
to select Stereo or Mono.
Displaying Subtitles
In digital broadcasts, this feature will show subtitles
on the screen in the selected language provided they
are being broadcast.
• Press SUBTITLE button to activate available
subtitles. Press SUBTITLE button again to turn off
subtitles.
Viewing Main Menu
• Press MENU button on the remote control to view
main menu.
Controlling Volume and Muting Sound
Volume
Press
Sound Mute
Press “
again to cancel.
or button to adjust the volume.
” button once to turn the sound off and
Selecting Programme Positions
To select a programme position use the numeric
buttons on the remote control. Programme positions
can also be selected using
Press
i.e. programme position, stereo/mono signal and
picture format.
You can view stored channels and sort them by using the Channel List feature.
English
Viewing Channel List
The channel order may be changed to suit your personal
preference.
Select • Channel List from the main menu and press OK button. The following menu will be displayed:
Select • Edit Channel List to manage all stored
channels. Use Up or Down and OK buttons to select
Edit Channel List.
Press • Up or Down button for selecting a channel.
You can press
page down.
To watch a specifi c channel, highlight it by using • Up
or Down button. Afterwards press OK button.
Press • BLUE button to view fi ltering options.
Press • MENU button to exit.
or button to move page up or
Moving a Channel
Highlight the desired channel by using • Up or Down
button.
Select Move option in the channel list and press •
OK button.
Edit Number screen will be displayed. Enter the •
desired channel number by using the numeric
buttons on the remote control. If there is a previously
stored channel on that number, a warning screen
will be displayed. Select Yes if you want to move the
channel and press OK.
Selected channel is now moved.•
Deleting a Channel
You can press GREEN button to tag/untag all
channels; YELLOW button to tag/untag channel.
Select the channel that you want to delete and select •
Delete option. Press OK button to continue.
A warning screen will appear. Select • Yes to delete,
select No to cancel. Press OK button to continue.
Renaming a Channel
Select the channel that you want to rename and •
select Edit Name option. Press OK button to
continue.
Pressing • Left or Right button moves to the previous/
next character. Pressing Up or Down button
changes the current character. Pressing the numeric
buttons ‘0...9’ replaces the highlighted character with
the characters printed above the button one by one
as the button is pressed.
When finished, press • OK button to save. Press
MENU to cancel.
Locking a Channel
You can press GREEN button to tag/untag all
channels; YELLOW button to tag/untag a single
channel.
Select the channel that you want to lock by using •
Up or Down button.
Select • Lock option by using Left or Right button.
Press OK button to continue.
You will be asked to enter parental control PIN. Enter •
the PIN number.
Note: Default PIN is set to 0000.
Press • OK button when the desired channel is
highlighted to lock/unlock the channel. Lock symbol
will be displayed next to the selected channel.
Press • button. The information screen will appear
giving details of the channel and programme
currently being viewed.
Whenever you change channel, the TV displays the •
broadcast picture along with an information banner at
the bottom of the screen (available only in DTV mode).
This will remain on the screen for a few seconds.
If the selected channel is locked, you must enter the •
correct four numeric code to view the channel. “Enter
PIN” will be displayed on the screen in such a case:
Enter the 4-digit PIN number to continue.•
Electronic Programme Guide
Select the on-screen guide by pressing • GUIDE
button, the guide screen will appear highlighting
details of the channel and programme currently
being viewed. This may take a few moments to
appear.
Press • GREEN button to list the schedule.
Press • BLUE button to display fi ltering options.
Note: There are alternative views of EPG screen.
Button functions will be displayed at the bottom of
the menu screen.
For information on a highlighted programme, press •
button.
For details of other programmes currently available, •
press navigation buttons to scroll up and down
or scroll left/right through the list. As channels are
selected, details of the programme currently being
broadcast will appear.
To set the timer for a selected programme, press •
OK button to select Timers menu.
Digital Settings - Parental Control, Menu Lock, Set PIN
You can view or set parental preferences of your TV.
Viewing Parental Control Menu
Press MENU button and select the Settings by using
Left or Right button. Press OK button to view Settings
menu. Use Up or Down button to highlight Parental
and press OK to continue:
A dialogue box asking for the lock key will be •
displayed. The default key is set to 0000. Enter
the PIN.
If it is incorrect, “• Wrong PIN” OSD will be displayed.
If it is correct, the Parental Control menu will be
displayed:
Menu Lock
In Menu lock you can set locking for All menus, or the
Installation menu to restrict access to these menus.
If the menu lock is disabled, there will be free access
to the menu system.
Use • Up or Down buttons to go to Menu Lock
option. Use Left or Right buttons to choose Menu
Lock Mode.
OFF : All menus are unlocked.
ALL MENUS : All Menus are accessible only with
the correct lock key. So the user cannot add, delete,
rename, channels, cannot set timers.
INSTALLATION MENU: Installation menu is locked.
So the user can’t add channels.
Maturity Lock (*)
When set, this option gets the maturity information
from the broadcast and if this maturity level is disabled,
disables access to the broadcast. Press MENU button
and select Settings by using Left or Right button.
Press OK button to continue. Use Up or Down
button to select Parental and then press OK button
to continue. Enter the pin number.
(*) Not available for UK.
Child Lock
Child Lock disables the buttons on the TV except
/ and / buttons. All buttons on the remote
control can still be used. Press MENU button and
select Settings by using Left or Right button. Press
OK button to continue. Use Up or Down button to
select Parental and then press OK button to continue.
Enter the pin number.
Set PIN
Use • Up or Down buttons to select Set PIN option.
Press OK to display the Set PIN window.
Use numeric buttons to enter new pin number. You •
will need to input your new pin a second time for
verifi cation purposes.
After typing correct PIN numbers, PIN number will •
be changed.
Note: The factory default pin number is 0000, if you
change the pin number make sure you write it down
and keep it safe.
You can confi gure picture settings of your TV by using Picture Settings menu.
English
Confi guring Picture Settings
You can use different picture settings in detail. You
can customize current picture mode settings as
desired. For example, you can change items such as,
Brightness, Contrast, Colour, Sharpness and Hue.
Press MENU button and select Picture by using Left
or Right button. Press OK button to view Picture
Settings menu.
Operating Picture Settings Menu Items
Press • Up or Down button to highlight a menu
item.
Use • Left or Right button to set an item.
Press • MENU button to exit.
Picture Mode
This TV offers the choice of personalising the picture
style. Cinema, Game, Dynamic and Natural are preset
options and affect settings within the TV. Press MENU
button and select Picture by using Left or Right
button. Press Up or Down button to select Mode.
• In the Picture Settings menu, press Up or Down
button to select Mode. Press Left or Right button to
select the picture mode you prefer.
Contrast
Sets the lightness and darkness values of the screen.
Press MENU button and select Picture by using Left
or Right button. Press Up or Down button to select
Contrast.
Brightness
Sets the brightness value for the screen. Press
MENU button and select Picture by using Left or
Right button. Press Up or Down button to select
Brightness.
Sharpness
Sets the sharpness value for the objects displayed on
the screen. Press MENU button and select Picture by
using Left or Right button. Press Up or Down button
to select Sharpness.
Colour
Sets the colour value, adjusting the colours. Press
MENU button and select Picture by using Left or
Right button. Press Up or Down button to select
Colour.
Colour Shift
Adjust the desired colour tone. Press MENU button
and select Picture by using Left or Right button.
Press Up or Down button to select Colour Shift.
Colour Temp
Colour Temperature increases the ‘warmth’ or
‘coolness’ of the picture by increasing the red or
blue tint.
In the • PICTURE menu, press Up or Down to select
Colour Temp.
Press • Left or Right to choose from one of these
options: Cool, Normal and Warm.
Note:
• Setting Cool option gives white colours a slight
blue stress.
• Setting Warm option gives white colours a slight
red stress.
Sometimes some words or picture elements may
become distorted or pixelated. Using the Noise
Reduction feature reduces this effect by smoothing out
the edges. Press MENU button and select Picture by
using Left or Right button. Press Up or Down button
to select Noise Reduction.
Picture Zoom
Sets the picture size to auto,16:9, subtitle,14:9, 14:9
zoom, 4:3, panoramic or cinema. Press MENU button
and select Picture by using Left or Right button.
Press Up or Down button to select Picture Zoom.
Reset
This feature allows you to reset the current Picture
Settings to the default values. Press MENU button
and select Picture by using Left or Right button.
Press Up or Down button to select Reset and press
OK button.
Note: The reset function does not reset the settings for
Mode, Colour Temp, Noise Reduction, Picture Zoom
and HDMI True Black.
Depending on the type of broadcast being transmitted, programmes can be viewed in a number of formats.
Press QUICK button and select Picture Zoom. Press OK button repeatedly to select between auto, 16:9, subtitle, 14:9, 14:9 zoom, 4:3, panoramic or cinema. When auto is selected the format being displayed is
determined by the picture being broadcast.
Note: Using the special functions to change the size of the displayed image (i.e. changing the height/width
ratio) for the purposes of public display or commercial gain may infringe on copyright laws.
Use this setting when watching a
widescreen DVD, widescreen video
16:9
subtitle
14:9
tape or a 16:9 broadcast (when
available). Due to the range of
widescreen formats (16:9, 14:9 etc.)
black bars may be visible on the top
and bottom of the screen.
When subtitles are included on a
letterbox format broadcast, this
setting will raise the picture to ensure
that all the text is displayed.
This zooms up the wide picture (14:9
aspect ratio) to the upper and lower
limits of the screen
You can set PC Mode picture settings when using the TV as a PC monitor.
PC Picture Settings (*)
(*) While in VGA/PC mode, some items in Picture
menu will be unavailable. Instead, VGA mode settings
will be added to the Picture Settings while in VGA/
PC mode.
PC Picture controls
Contrast, Brightness and Colour Temperature
adjustments in this menu are identical to adjustments
defi ned in TV picture menu.
Select Reset and press OK button to reset the
adjustments.
Note:
For switching to VGA/PC source, press
your remote control and select VGA/PC input.
Note that VGA/PC mode menu settings are available
only while the TV is in PC source.
button on
PC Position
Select this to display PC position menu items.
Autoposition
If you shift the picture horizontally or vertically to an
unwanted position, use this item to put the picture into
correct place automatically.
Select the • PC Position option from the main menu.
Press OK to display the PC Position submenu.
Press the • Down button to highlight Autoposition
and then press the OK button.
H Position
H (Horizontal) Position shifts the image horizontally to
right hand side or left hand side of the screen.
In the • PC Position menu press the Down button
until H Position is highlighted.
Press the • Left or Right button to adjust the value.
V Position
V (Vertical) Position shifts the image vertically towards
the top or bottom of the screen.
In the PC Position menu press the Down button until
V Position is highlighted.
Press the Left or Right button to adjust the value.
Dot Clock
Dot Clock adjustment corrects the interference
that appear as vertical banding in dot intensive
presentations like spreadsheets or paragraphs or
text in smaller fonts.
In the • PC Position menu press the Down button
until Dot Clock is highlighted.
Press the • Left or Right button to adjust the value.
Phase
Depending on the resolution and scan frequency that
you input to the TV Set, you may see a hazy or noisy
picture on the screen. In such a case you can use this
item to get a clear picture by trial and error method.
In the • PC Position menu press the Down button
until Phase is highlighted.
Press the • Left or Right button to adjust the value.
You can confi gure sound settings of your TV by using Sound Settings menu.
English
Confi guring Sound Settings
Sound settings can be confi gured according to your
personal preferences.
Press MENU button and select Sound by using Left
or Right button. Press OK button to view Sound
Settings menu.
Operating Sound Settings Menu Items
Press • Up or Down button to highlight a menu
item.
Use • Left or Right button to set an item.
Press • MENU button to exit.
Volume
Press MENU button and select Sound by using Left
or Right button. Press OK button to continue.
Select Volume using Up or Down button and then use
Left or Right button to set volume level.
Equalizer (Only for speaker)
You can customize current sound mode settings. Select
the appropriate mode in accordance with the installation
location of the TV and adjust the equalizer on-screen as
desired. Press OK button to view equalizer submenu.
In equalizer menu, the preset can be changed to
Music, Movie, Speech, Flat, Classic and User.
Press the MENU button to return to the previous
menu.
Note: Equalizer menu settings can be changed
manually only when the EqualizerMode is in User.
Balance (Only for speaker)
This setting is used for emphasizing left or right
speaker balance.
Press • Left or Right button to change the level of
the balance. Balance level can be adjusted between
-31 and +31.
Headphone
This setting is used to set the sound output when
headphones are connected.
Press • Up or Down button to select Headphone.
Press • Left or Right button to select Volume. Press
Right button to increase headphone volume level.
Press Left button to decrease headphone volume
level. Headphone volume level can be adjusted
between 0 and 63.
AVL
Sometimes there can be large changes in volume
when switching from a DTV 5.1ch to a DTV 2ch, an
ATV channel, or an external input. Using the AVL
feature reduces these volume differences.
In the • Sound menu, press Up or Down to highlight
AVL . Press Left or Right button to set AVL as On
or Off.
Dynamic Bass
Dynamic Bass is used to increase bass effect of the
TV set.
Press MENU button and select Sound by using Left
or Right button. Press OK button to continue. Select
Dynamic Bass using Up or Down buttons and press
Left or Right button to set.
Digital Out
This setting enables you to set Digital Out preference
as Compressed or PCM. You should set this feaure in
accordance with the received broadcast’s content.
Press MENU button and select Sound by using Left
or Right button. Press OK button to continue.
Select Digital Out using Up or Down button and then
use Left or Right button.
Detailed settings can be configured to suit your
personal preferences.
Viewing Settings Menu
Press MENU button and select Settings by using Left
or Right button. Press OK button to view Settings
menu.
Operating Settings Menu Items
Press • Up or Down button to highlight a menu item.
Press • OK button to select an item.
Press • MENU button to exit.
Conditional Access
This setting controls conditional access modules
when available. Select Settings from the main menu
by using Left or Right button and press OK button.
Afterwards, use Up or Down button to set Conditional
Access. Press OK button to continue.
Language
Confi gures language settings. See page 21.
Parental
Confi gures parental settings. See page 22.
Timers
Sets timers for selected programmes. See page 29.
Date/Time Settings
You can confi gure date/time preferences by using this
menu screen. See page 29.
Sources
Enables or disables selected source options. See
page 30.
Other Settings
Displays other setting options of the TV set.
Using a Conditional Access Module
The Common Interface Slot, situated on the side of the
television, enables the insertion of a CAM (Conditional
Access Module) and card. These are purchased from
a service provider and allow additional subscription
broadcasts to be viewed. For more information, see
a service provider.
IMPORTANT: Insert or remove the CI module only
when the TV is SWITCHED OFF.
In order to watch certain digital channels, a •
conditional access module (CAM) is necessary. This
module must be inserted in the CI slot of your TV.
Obtain the Conditional Access Module (CAM) and •
the viewing card by subscribing to a pay channel
company, then insert those to the TV using the
following procedure.
Insert the CAM and then the viewing card to the •
slot that is located in the terminal cover at the rear
side of the TV.
The CAM should be correctly inserted, it is •
impossible to insert fully if reversed. The CAM or
the TV terminal may be damaged if the CAM is
forcefully inserted.
Connect the TV to the mains supply, switch on and then
wait for few moments until the card is activated.
When no module is inserted, “• No Common Interface module detected” message appears on the screen.
Refer to the module instruction manual for details •
of the settings.
Viewing Conditional Access Menu (*)
(*) These menu settings may change depending on
the service provider.
Press MENU button and select Settings by using
Left or Right button. Press OK button to view Settings menu. Use Up or Down button to highlight
Conditional Access and press OK to view menu
To view Timers menu, press MENU button and select
Settings by using Left or Right button. Press OK
button to view Settings menu. Use Up or Down button
to highlight Timers and press OK to continue:
Setting Sleep Timer
The television can be set to turn itself Off after a
certain length of time.
Highlight • Sleep Timer by using Up or Down
button.
Use • Left or Right button to set. The timer can be
programmed between Off and 2.00 hours (120
minutes) in steps of 30 minutes.
Setting Programme Timers
This feature will set the television to go to a specifi c
channel at a certain time. It can be used to view
a particular programme, or by setting the mode
to daily or weekly, can be used to view a series of
programmes.
Press Down button to set timers on an event.
Programme timer function buttons will be displayed
on the screen.
Note: That this feature will be available only when a
timer has been programmed.
Adding a Timer
Press • YELLOW button on the remote control to
add a timer. The following menu appears on the
screen:
Channel: Changes channel by using Left or Right.
Timer/Record Type: This feature is unavailable to
be set.
Date: Enter a date using the numeric buttons.
Start: Enter a starting time using the numeric
buttons.
End: Enter an ending time using the numeric
buttons.
Duration: Displays duration between the starting and
ending time.
Repeat: Sets a timer to be repeated as Once, Daily
or Weekly. Use Left or Right button to select an
option.
Change/Delete: Controls parental settings on timers.
Press • GREEN button to save the timer. Press RED
button to cancel.
English - 29 -
Editing a Timer
Select the timer you want to edit by pressing • Up or
Down button.
When fi nished with editing, press • GREEN button to
save. You can press MENU button to cancel.
Deleting a Timer
Select the timer you want to delete by pressing • Up
or Down button.
Press • RED button.
Select • Yes by using Left or Right button to delete
the timer. Select No to cancel.
Confi guring Date/Time Settings
You can confi gure date/time preferences by using
Select • Date/Time in the Settings menu to confi gure
Date/Time settings. Press OK button.
Use or button to highlight the Time Settings
Mode. Time Settings Mode is set using or button.
It can be set to AUTO or MANUAL.
When AUTO is selected, Date/Time and Time Zone
options will not be available to be set. If MANUAL
option is selected as the Time Zone can be altered:
• By pressing
or button to change the Time Zone between
Use
GMT-12 or GMT+13. Date/Time on the top of the
menu list will then change according to the selected
Time Zone.
Note: For countries without Digital channels, only the
Date and Time option will be displayed.
You can enables or disable selected source options.
The TV will not switch to the disabled source options
when
Select• Sources in the Settings menu and press
OK button.
Press • Up or Down buttons to select a source.
Use • Left or Right button to enable or disable the
selected source. Changes are automatically stored.
button is pressed.
Input Selection
Use the Input Selection window if the television
does not switch over to a connected source
automatically.
• Press
changing sources. Use the Up or Down button to
highlight an input and press Right button to select.
button on your remote control for directly
Confi guring Other Settings - General
You can confi gure the settings of your TV. Select Settings from main menu and press OK to view the
Settings menu. Press the MENU button on the remote
control to exit.
To view general confi guration preferences, select Other Settings in the Settings menu and press OK
button.
Operation
Press • Up or Down button to select an item.
Use • Left or Right button to set an option.
Press• OK button to view a sub-menu.
Menu Timeout
To set a specifi c display timeout for menu screens,
set a value for this option.
In the Other Settings menu, select Menu Timeout
and choose 15 sec, 30 sec or 60 sec using Left or
Right button.
Scan Encrypted
When this setting is on, search process will locate
the encrypted channels as well. If it is set as OFF
manually, encrypted channels will not be located
while in automatic search or manual search. Scan
Encrypted Channel feature will always be ON after
performing first time installation.
In the • Other Settings menu, use Up or Down button
to select Scan Encrypted.
Press • Left or Right button to set this function as
Select Backlight by pressing Up or Down button.
Press Left or Right button to set Backlight to Auto,
Medium, Maximum or
Note:Backlight adjustment is not available when
Power Save mode is switched ON. Please see page
13 of this manual for explanation.
Minimum.
Power Save Mode
Use Up or Down button to select Power Save Mode.
Press Left or Right button to set Power Save Mode
as On or Off.
See the section, “Environmental Information” in
this manual for further information on Power Save
Mode.
Note : Backlight function will be skipped if Power Save
Mode is set to on.
Blue Background
If the signal is weak or absent, the TV will automatically
change to a blue screen. To enable this, set Blue
Background to On.
In the • Other Settings menu, select Blue
Background and choose On or Off using Left or
Right button.
Software Upgrade
This feature helps to keep your TV updated. It works
automatically and searches for new information
when available. Note that this setting is inactive to
be modifi ed.
To ensure that your TV always has the most updated
information, you can use this setting. In order for the
proper operation, please ensure that the TV is set to
standby mode.
You can enable or disable automatic upgrade by
setting Automatic Scanning option.
You can manually search for new software by
selecting Scan for upgrade.
Hard of Hearing
If the broadcaster enables any special signal
concerning the audio, you can set this setting as On
to receive such signals.
Use • Up or Down button to select Hard of Hearing
and then press Left or Right button to set this setting
as On or Off.
Audio Description
Audio description refers to an additional narration
track for blind and visually impaired viewers of
visual media, including television and movies. The
description narrator talks through the presentation,
describing what is happening on the screen during the
natural pauses in the audio (and sometimes during
dialogue, if deemed necessary). You can use this
feature, only if the broadcaster supports that additional
narration track.
Highlight • Audio Description by pressing Up or
Down button.
Press • OK button to enter Audio Description
submenu.
Use • Up or Down button to select Audio Description
setup and then press Left or Right button to set
this setting.
Auto TV Off
You can set the timeout value of auto off feature.
After the timeout value is reached and the TV is not
operated for selected time, the TV will go off. Press
MENU button and select Settings by using Left or
Right button. Press OK button to continue. Use Up
or Down button to select Other Settings and then
press OK button. Select Auto TV Off using Up or
Down button.
Broadcast Type
Press MENU button and select Settings by using Left
or Right button. Press OK button to continue. Use Up
or Down button to select Other Settings and then
press OK button. Select Broadcast Type using Up or Down button and use Left or Right button to set.
When you set the desired broadcast type by using
Left or Right button, the TV will display the selected
broadcast type.
(*) This setting is visible only when the Country option
is set to Denmark, Sweden, Norway or Finland.
If the Standby Search is set to On and the TV is in
standby mode, the TV will look for any changes in
the saved channels. Press MENU button and select
Settings by using Left or Right button. Press OK
button to continue. Use Up or Down button to select
Other Settings and then press OK button. Select
Standby Search using Up or Down button and use
Left or Right button to set.
Full Mode (optional)
If you connect a device via HDMI or YPbPr connectors
and set 1080i/1080p resolutions, Full Mode item will
be visible.
Teletext language
Use this setting to set a preferred Teletext language.
Press MENU button and select Settings by using Left
or Right button. Press OK button to continue. Use Up
or Down button to select Language and then press
OK button. Select Teletext language using Up or
Down button and use Left or Right button to set.
HDMI True Black
While watching from HDMI source, this feature will be
visible in the Picture Settings menu.
You can use this feature to enhance blackness in the
picture. You can set this feature as “On” for activating
HDMI True Black mode. Press MENU button and
select Picture by using Left or Right button. Press OK
button to continue. Select HDMI True Black using Up
or Down button and use Left or Right button to set.
Note: HDMI True Black On/Off feature functions only
when the HDMI device output is set to RGB.
This TV allows you to enjoy photo, video or music fi les stored on a USB memory.
English
Manual Start
To display Media Browser window, you can press •
MENU button on the remote control and then select
Media Browser by pressing Left or Right button.
You can also press the QUICK button to select
Media Browser.
Press • OK button to continue. Media Browser menu
contents (depending on the contents of your USB
memory) will be displayed.
Auto Start
When you plug a USB memory, the following menu •
will be displayed.
You can play music, picture and video fi les from a •
USB memory.
To display All fi les in a list, select Settings tab and •
change View Style to Folder. Then go back to main
media browser screen and you will see that now
All tab will be available. Select All tab and press
OK button.
Note:
Some USB compliant devices may not be supported.
If the USB memory is not recognized after power off/
on or First Time Installation, plug the USB memory
out and power off/on the TV set. Then plug the USB
memory in again.
Do not use a USB Hub.•
You must obtain any required permission from •
copyright owners to use copyright content.
Toshiba cannot and does not grant such permission.
Depending on the fi le size and amount in your USB •
memory, it may take some time for loading to view.
A message will display on-screen when loading fi les
from the USB memory.
Only limited types of U3 USB device are supported. •
Therefore, it is suggested not to use U3 USB for
playing Media Player.
English - 33 -
Non-supported characters will be replaced with a •
square (□).
Playing MP3 Files
To play mp3 fi les from a USB memory, you can use
this menu screen.
When you select Music from Media Browser, available
music fi les will be fi ltered and listed on this screen.
If you select View Style as Folder from the Media
Browser Settings menu, you can display files in
accordance with the folder path. However, only the
selected fi le types will be visible.
Use • Up or Down button to highlight a fi le.
0..9 (Numeric buttons):• The TV will jump to the
fi le starting with the letter you input via the numeric
buttons on your remote control.
Use•
button to stop playback.
button to play all media fi les in the folder
Press •
starting with the selected one.
button to pause a playing fi le.
Press •
Use • GREEN button to play the selected file
repeatedly or in shuffl e mode.
Press • RED button to sort fi les by Title, Artist or
Album.
This TV allows you to enjoy photo, video or music fi les stored on a USB memory.
Viewing JPEG Files
To view photo fi les from a USB memory, you can use
this menu screen. When you select Photos from
Media Browser, available image fi les will be fi ltered
and listed on this screen.
If you select View Style as Folder from the Media
Browser Settings menu, you can display files in
accordance with the folder path. However, only the
selected fi le types will be visible.
Use • Numeric Buttons to jump to the previous or
next fi le. Press OK button to play.
Press • OK button to view the selected picture in
full screen.
Press button to start a slideshow.
Press RED button to sort fi les by date.
Press GREEN button to view thumbnails.
Press YELLOW button to change the viewing style.
Press BLUE button to change media type.
Slideshow Feature
You can use this feature to display photos on your
TV.
This TV allows you to enjoy photo, video or music fi les stored on a USB memory.
English
Video Playback
When you select Videos from Media Browser,
available video fi les will be fi ltered and listed on this
screen. You can use Up or Down button to select a
video fi le and press OK button to play a video.
Note: If you set View Style from Media Browser
Settings menu as ‘Folder’, media browser main selection screen will include All tab as well.
Subtitle Selection: If you select a subtitle fi le and
press OK button, you can select or deselect that
subtitle fi le. You can turn the subtitle on or off by using
the SUBTITLE button.
Use • Up or Down button to highlight a fi le.
Press • OK button to start the video playback and play
the selected fi le. Press
The following menu will be displayed while playing
a video fi le:
Press • button to stop the video playback.
button to pause the video playback.
Press •
Press •
Press •
Use • AD button to set subtitle/Audio.
Use • GREEN button to jump to a time.
Use • YELLOW button to open subtitle time correction
menu.
button to go backward.
button to go forward.
button to play all.
Note:
You can set subtitles by using OK button before
starting the playback or by using AD button during
the playback. Selected subtitles may not be displayed
correctly in some cases.
In order to display movie subtitles correctly, you should
set a “Movie Subtitle” language. You should display
Language Settings menu for setting a Movie Subtitle
language. See the section, “Language Settings” on
page 21 for displaying Language Settings menu.
Press • RETURN button to switch back to previous
menu.
Media Browser Settings
You can set your Media Browser preferences by
using the Settings dialogue. Press Up or Down
button to highlight an item and use Left orRight
button to set.
View Style: Sets default browsing mode.
Slideshow Interval: Sets slide show interval time.
Show Subtitle: Sets subtitle enabling preference.
Subtitle Language: Sets supported subtitle
language.
Subtitle Position: Sets subtitle position as up or
down.
Subtitle Font Size: Sets subtitle font size (max.
54pt).
This television has a multi-page text memory, which takes a few moments to load.
Analogue Text Services
Before using the text services, the required language
region must be chosen.
Select • Language from the Settings menu.
Press the • Left or Right button to choose the required
language region.
After the Teletext language is selected, press • MENU
button to exit.
Using Text Button -TEXT
To view text services press • TEXT. Press TEXT
again to superimpose text over a normal broadcast
picture.
TEXT again to return to normal viewing.
Press •
Programmes cannot be changed until text is •
cancelled.
The fi rst text page shown will be the initial page.•
Any text page can be accessed by entering the 3 •
digit page number using the numbered buttons,
pressing the coloured buttons or pressing to
advance to the next page and to go back to the
previous page.
Four coloured titles will appear at the base of the •
screen. To access one of the four given subjects,
press the relevant coloured button on the remote
control.
For further information on your particular text •
system(s), see the broadcast text index page or,
consult your local Toshiba dealer.
Below is a guide to the functions of the remote control
text buttons.
Acessing Sub-Pages
If a text page has sub-pages, press and enter the subpage numbers 01,02,03 etc. which can be selected
using Left/ Right buttons at the bottom of the text page
under the coloured links.
Revealing Concealed Text
To discover the solutions on quiz and joke pages
press the button.
Holding a Page
At times it is convenient to hold a page of text. Press
and HOLD will appear in the top left of the screen.
The page will be held on screen until the button is
pressed again.
To display an initial page
Press to access an initial page. The one displayed
is dependant on the broadcaster.
Appendix B: AV and HDMI Signal Compatibility (Input Signal Types)
English
SourceSupported SignalsAvailable
PAL 50/60O
EXT
(SCART)
SIDE AV
YPbPr
HDMI1
HDMI2
NTSC 60O
RGB 50O
RGB 60O
PAL 50/60O
NTSC 60O
480i60HzO
480p60HzO
576i50HzO
576p50HzO
720p50HzO
720p60HzO
1080i50HzO
1080i60HzO
1080p50HzO
1080p60HzO
480i60HzO
480p60HzO
576i50HzO
576p50HzO
720p50HzO
720p60HzO
1080i50HzO
1080i60HzO
1080p50HzO
1080p60HzO
1080p24HzO
(X: Not Available, O: Available)
Note: In some cases a signal on the LCD TV may not be displayed properly. The problem may be an
inconsistency with standards from the source equipment (DVD, Set-top box, etc.). If you do experience such
a problem please contact your dealer and also the manufacturer of the source equipment.
HDMI, the HDMI logo, and High-Defi nition Multimedia Interface are trademarks or registered trademarks of •
HDMI Licensing LLC in the United States and other countries.
DVB is a registered trademark of the DVB Project.•
[1] EIA/CEA-861-D compliance covers the transmission of uncompressed digital video with high-bandwidth •
digital content protection, which is being standardized for reception of high-defi nition video signals.
Because this is an evolving technology, it is possible that some devices may not operate properly with the
television.
®
DivX•
, DivX Certifi ed® and associated logos are trademarks of DivX, Inc. and are used under license.
MP3 licence letter
MPEG Layer-3 audio coding technology licensed from Fraunhofer LLS and Thomson.
AVC licence letter
THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFORIO LICENSE FOR THE PERSONAL
AND NON-COMMERCIAL USE OF A CONSUMER TO (I)ENCODE VIDEO IN COMPLIANCE WITH THE AVC
STANDARD (“AVC VIDEO”) AND/OR (II)DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER
ENGAGED IN A PERSONAL AND NON-COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO
PROVIDER LICENSED TO PROVIDE AVC VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED
FOR ANY OTHER USE. ADDITIONAL INFORMATION MAY BE OBTAINED FROM MPEG LA,L.L.C. SEE
HTTP//WWW.MPEGLA.COM
Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of
Dolby Laboratories.
Cleaning the screen and cabinet...
Turn off the power, clean the screen and cabinet with a soft, dry cloth. We recommend that you do not use any proprietary
polishes or solvents on the screen or cabinet as this maycause damage.
Disposal...
The following information is only for EU-member states:
Disposal of products
The
crossed out wheeIed dust bin symbol indicates that products must be collected and disposed of separately from
household waste. Integrated batteries and accumulators can be disposed of with the product. They will be separated
at the recycling centres.
The black bar indicates that the product was placed on the market after
By participating in separate collection of products and batteries, you will help to assure the proper disposal of
products and batteries and thus help to prevent potential negative consequences for the environment and human
health.
For more detailed information about the collection and recycling programmes available in your country,
contact your local city office or the shop where you purchased the product.
Disposal of batteries and/or accumulators
The crossed out wheeled dust bin symboI indicates that batteries and/or accumulators must be collected and
disposed of separately from household waste.
If the battery or accumulator contains more than the specified values
cadmium (Cd) defined in the Battery Directive (2006/66/EC), then the chemical symbols for lead (Pb), mercury (Hg)
and/or cadmium (Cd) will appear below the crossed out wheeled dust bin symbol.
By participating in separate collection of batteries, you will help to assure the proper disposal
batteries and thus help to prevent potential negative consequences for the environment and human health. For more
detailed information about the coIIection and recycling programmes available in your country, please contact your
local city office or the shop where you purchased the product.
Check the TV is not in standby mode.
Check the mains plug and all mains connections.
A
Why is there a picture but no sound?
Q
Check the volume has not been turned down or
that sound mute has not been selected.
A
What can cause a poor picture?
Q
Interference or a weak signal. Try a different TV
station.
A
Why doesn't the video/DVD being played show
Q
on screen?
Make sure the VCR or DVD player is connected to
the TV as illustrated in the beginning chapters, then
A
select the correct input by pressing .
Why is the VCR/DVD picture in black and white?
Q
in
Why is there a good video picture but no sound?
Q
Check the SCART lead connection.
A
Why doesn't the remote control work?
Q
Check the batteries aren't dead or inserted
incorrectly.
A
Why doesn't the TV OSD settings saved?
Q
Ensure to turn off the power first before attempting
to unplug the AC cord. Otherwise, the settings may
A
not be saved.
Why don't the controls of the TV work?
Q
Check that CHILD LOCK is not selected.
A
Why is the sound only coming from one speaker
Q
when stereo sound is selected?
Check that the balance in the SOUND menu hasn't
been set to one side.
A
Why are there problems with analogue text
Q
service?
Good performance of the analogue text depends
on a good strong broadcast signal. This normally
A
requires a roof or loft aerial. If the text is
unreadable or garbled, check the aerial. Go to the
main index page of the analogue text service and
look for the User Guide.
What is DVB-T?
Q
Digital Video Broadcast via an aerial/antenna.
A
How are radio channels selected?
Q
n.
.
You can select them via the Channel List.
What can be done if the PIN number has been
Q
A
Q
A
otten?
Incase of password is forgotten, Please press
1,2,7,6 or 4,7,2,5 buttons from remote control
respectively in order to enter parental setting
menu. Define a new pin number in Set PIN section.
You will need to enter your new PIN a second time
for verification purposes.
Why are there horizontal stripes and/or blurred
images on the screen when in PC mode?
The Phase may need adjustment. Select PC
Settings and highlight Phase and adjust until the
picture is clear.
Make sure that USB memory is connected correctly.
Incorrect behaviour may occur with a USB Hub
A
connection.
Why is the digital channel locked?
Q
Parental control is activated. Check parental settings.
A
Why are some encrypted digital channels
unavailable?
Q
Your subscription needs upgrading. Contact your
service provider.
A
Why when digital subtitles have been selected
Q
are they not showing on screen?
Subtitles are not currently being transmitted by the
broadcaster.
A
Why is the soundtrack in English when a
Q
different audio language has been selected?
The programme is currently being broadcast with
an English soundtrack only.
A
Why does the active standby LED sometimes
Q
take longer to go out?
When put into standby, the TV's active
standby will automatically search all available
A
channels for downloads, provided Automatic
Download is enabled. The time taken to do this
may vary.
EU Conformity Statement
“This product is marked with “CE” and complies therefore with the applicable harmonized European standards listed
under the Low Voltage Directive 2006/95/EC and the EMC Directive 2004/108/EC.”
Responsible for CE-marking is TOSHIBA EUROPE GMBH
Hammfelddamm 8, D-41460 Neuss, Germany
DVD Player is a class 1 laser product. However this
product uses a visible laser beam which could cause
hazardous radiation exposure. Be sure to operate the
player correctly as instructed.
CLASS 1
LASER PRODUCT
On cleaning
• Before playing, clean the disc with a cleaning cloth.
Wipe the disc from the center out.
English
RISK OF ELECTRIC SHOCK
The lightning flash with arrowhead
symbol, within an equilateral triangle, is
intended to alert the user to the presence
of uninsulated “dangerous voltage” within
the product’s enclosure that may be of
suffi cient magnitude to constitute a risk
of electric shock to people.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions
in the literature accompanying the
appliance.
Notes on Discs
On handling discs
• To keep the disc clean, handle the disc by its edge.
Do not touch the surface.
• Do not stick paper or tape on the disc.
• If the disc is contaminated with any substance like
glue remove before using it.
• Do not expose the disc to direct sunlight or heat
sources such as hot air ducts, or leave it in a car
parked in direct sunlight as the temperature can rise
quickly and damage the disc.
• After playing, store the disc in its case.
• Do not use solvents such as benzine, thinner,
commercially available cleaners or anti-static spray
intended for vinyl LPs.
Notes on moisture
condensation
Moisture condensation damages the DVD video
player. Please read the following carefully.
Moisture condensation occurs, for example, when you
pour a cold drink into a glass on a warm day. Drops
of water form on the outside of the glass. In the same
way, moisture may condense on the optical pick-up
lens inside this unit, one of the most crucial internal
parts of the DVD video player.
Moisture condensation occurs during the
following cases:
• When you bring the unit directly from a cold place
to a warm place.
• When you use the unit in a room where you just
turned on the heater, or a place where the cold wind
from the air conditioner directly hits the unit.
• In summer, when you use the unit in a hot and
humid place just after you move the unit from an air
conditioned room.
• When you use the unit in a humid place.
Do not use the unit when moisture condensation
may occur.
If you use the unit in such a situation, it may damage
discs and internal parts. Remove the disc, connect
the power cord of the unit to the wall outlet, turn on
the unit, and leave it for two or three hours. After two
or three hours, the unit will have warmed up and
evaporated any moisture. Keep the unit connected
to the wall outlet and moisture condensation will
seldom occur.
technology that is protected by U.S. patents
and other intellectual property rights. Use of
this copyright protection technology must be
authorized by Rovi Corporation, and is intended for
home and other limited viewing uses only unless
otherwise authorized by Rovi Corporation. Reverse
engineering and disassembly are prohibited.
How to Watch a DVD
When placing a disc into the loader, labelled side of
the disc should be on the front:
When TV set is turned on, fi rst switch to DVD source
by using the button on the remote control. Press
on the remote control, or directly press button
at the side panel. If there is no disc inside the loader,
place a DVD fi rst and then press .
You can operate DVD, movie CD, music or picture CD’s content by using the proper buttons on your remote
English
control. Below are main functions of commonly used remote control buttons.
Buttons on the
Remote Control
ANGLEViews the scene
SETUP Displays disc information / Displays DVD setup menu during stop mode.
MENUDisplays main menu.
OK
REPEAT Displays repeat options.
RETURN
ROOT
JUMP (*)
SUBTITLE Subtitle on-off. Press repeatedly to switch
TITLE
ZOOM
DVD
Playback
Play Play Play Play
PausePausePausePause
StopStopStopStop
Skip
backward/forward
Highlights a menu item. /
Shifts the zoomed picture left or right (if available).
Highlights a menu item. / Shifts the zoomed picture up or down (if available).
Rapid reverse / Rapid advanceX
from different
angles
(if available).
Audio language XXX
Returns back to the previous menu (if available).
Goes back to the root folder (if available). X
Direct selection of scenes, time or file (track) number.
between subtitle options (if available).
Displays disc menu (if available). XX
Zooms picture. Press repeatedly to switch between zoom
Movie
Playback
Skip
backward/forward
XXX
Displays disc information.
Enter / View / Play
options.
Picture
Playback
Previous / Next Previous / Next
XX
Music
Playback
X
Rapid reverse /
Rapid advance
X
Other Functions – Button Combinations
+
[ + ] +
[ + ]
+
+
+
+
(*) You can switch to title by pressing numeric keys directly. You need to press 0 and then digit key to
switch one digit titles (example: to select 5, press 0 and 5).
The disc will be automatically loaded and play
commences if the disc does not have any menus
recorded on it.
A menu may appear on the TV screen after a few
moments or the fi lm may start immediately after the
introduction of the Film Company. This behaviour
depends on the disc content and may change.
Note: Steps 3 and 4 are available only when a menu
is recorded on the disc.
Press navigation buttons or the numeric 3.
button(s) to select the preferred title.
Press 4. OK button.
Play of the selected items now starts.The played item
may be a motion picture, a still picture or another
submenu depending on the disc.
For your reference:
If an action corresponding to a button is prohibited,
the “
Notes on Playback
” symbol will appear.
No sound will be heard during Rapid advance 1.
or Rapid reverse.
No sound will be heard during Slow motion play.2.
In some cases, the subtitle language is not 3.
changed immediately to the selected one.
When the preferred language is not selected even 4.
after pressing the button several times, it means
that the language is not available on the disc.
When the player is restarted or the disc is 5.
changed, the subtitle selection is automatically
changed back to the initial settings.
If a language is selected, not supported by the 6.
disc, the subtitle language will automatically be
set to the disc’s priority language.
Usually a circulation will happen while switching 7.
to another language, that is you can cancel
the subtitle by pressing SUBTITLE button a
number of times until “Subtitle Off” appears on
the screen.
When the power is turned on or the disc is 8.
removed, the language heard is the one
selected at the initial settings. If this language
is not recorded on the disc, only the available
language on the disc will be heard.
Some DVDs may not contain root and/or title 9.
menus.
Reverse stepping is not available.10.
English - 49 -
For your convenience:11.
If you attempt to enter a number greater than the total
time of the current title, the time search box disappears
and “
corner of screen.
Input Invalid” message appears on up-left
Slide Show is disabled when the ZOOM mode 12.
is on.
Setup Menu Items
Video Setup Page
Tv Type
TV Type is only available as ‘PAL’. The TV set also
supports NTSC signal; however, the signal will be
converted to PAL when it appears on the screen.
DivX(R) VOD
DivX® VOD provides the convenience of streaming
video in terms of quality and performance.
Language Setup Page
Osd Lang
You can select the default OSD language of the
player menus.
Audio
You can select the default audio language if supported
by the DVD disc.
Disc Menu
You can select the DVD’s disc menu language among
these languages. Disc menu appears in the selected
language, if supported by the DVD disc.
Subtitle
You can select the default subtitle language if
supported by the DVD disc.
If you choose Reset and press OK button, the
factory-presets are loaded. Parental level and parental
password does not change.
Downmix
This mode can be selected when the DIGITAL AUDIO
socket of the TV is used.
Surround: Surround sound output.
Stereo: Two channels stereo.
Parental (Parental Level)
Playing some DVDs can be limited depending on the
age of users. The “Parental Control” function allows
playback limitation level to be set by the parent.
Parental Level can be adjusted to one of the eight
levels. Level “8 Adult” adjustment let you watch all of
the DVD titles ignoring the DVD disc’s parental level.
You can watch the DVD discs, which has the same or
lower parental level than the player’s level only.
Password (Change Password):
Using this item you can change the current
password.
To change the password you will be prompted to
enter your old password. After you have entered
your old password, you can now enter the new 4-digit
password.
Note: Factory preset of the password is “0000”. You
have to enter XXXX digital password every time you
want to change the parental level. If you forget your
password please contact technical service.
English - 50 -
You can set Spdif Output as RAW or PCM. If you
select PCM from Spdif Output in DVD menu and
play DVD with Dolby audio, you can get audio output
with two channels via the speakers and the DIGITAL
AUDIO socket. If you select RAW from Spdif Output
in DVD menu and play DVD with Dolby audio,
speakers will be muted and you can get 5+1 Dolby
audio via the DIGITAL AUDIO socket.
Troubleshooting
The picture quality is poor (DVD)
• Make sure the DVD disc surface is not damaged.
(Scratch, fi ngerprint, etc.)
• Clean the DVD disc and try again.
See instructions described in “Notes on Discs” to clean
your disc properly.
• Ensure that the DVD disc is in the loader with the
label facing front.
• A damp DVD disc or condensation may effect the
equipment. Wait for 1 to 2 hours in Standby to dry
the equipment.
Disc does not play
• No disc in the machine.
Place a disc into the loader.
• Disc incorrectly loaded.
Ensure that the DVD disc is in the loader with the
label facing front.
• Wrong type of disc. The machine cannot play CDROMS etc.
• The region code of the DVD must match the
player.
Wrong OSD language
• Select the language in the set-up menu.
The language for the sound or
subtitles on a DVD cannot be changed
• Multilingual sound and/or subtitles not recorded on
the DVD.
• Try to change the sound or subtitles using DVD’s title
menu. Some DVD’s do not allow the user to change
these settings without using the disc’s menu.
• Angle can only be changed when the angle symbol
is displayed.
No picture
• Have you pressed the correct buttons on the remote
control? Try once more.
No sound
• Check the volume is set to an audible level.
• Make sure you have not switched the sound off
accidentally.
Distorted sound
• Check that the appropriate listening mode setting
is correct.
No response from remote control
• Make sure the remote control is in the correct
mode.
• Check batteries are fi tted correctly.
• Change the batteries.
If nothing works
If you have tried the above solutions and none seem
to work, try switching your TV off and on again. If this
does not work, contact your supplier or TV repair
technician. Never attempt to repair a defective TV
yourself.
Defi nition of Terms
Angle
Recorded onto some DVD discs are scenes, which
have been simultaneously shot from a number of
different angles (the same scene is shot from the
front, from the left side, from the right side, etc.). With
such discs, the ANGLE button can be used to view
the scene from different angles.
Chapter Number
These numbers are recorded on DVD discs. A title
is subdivided into many sections, each of which are
numbered, and specifi c parts of video presentations
can be searched quickly using these numbers.
DVD
This refers to a high-density optical disc on which
high-quality pictures and sound have been recorded
by means of digital signals. Incorporating a new video
compression technology (MPEG2) and high-density
recording technology. DVD enables aesthetically
pleasing full-motion video to be recorded over long
periods of time (for instance, a whole movie can be
recorded).
DVD has a structure consisting of two 0.6-mm thin
discs, which are adhered to each other. Since the
thinner the disc, the higher the density at which the
information can be recorded, a DVD disc has a greater
capacity than a single 1.2 mm thick disc. Since the
two thin discs are adhered to each other, there is the
potential to achieve double-sided play sometime in
the future for even longer duration play.
Subtitles
These are printed lines appearing at the bottom of
the screen, which translate or transcribe the dialogue.
They are recorded on the DVD discs.
Time Number
This indicates the playtime, which has elapsed from
the start of a disc or a title. It can be used to fi nd a
specifi c scene quickly. (Not all discs permit the time
search feature to be used. Availability is determined
by the disc’s manufacturer.)
Title Number
These numbers are recorded on DVD discs. When a
disc contains two or more movies, these movies are
numbered as title 1, title 2, etc.
Track Number
These numbers are assigned to the tracks, which are
recorded on Audio CDs. They enable specifi c tracks
to be located quickly.
LPCM
LPCM stands for Linear Pulse Code Modulation and
is digital audio.
MPEG
Short for Moving Picture Experts Group. This is an
international standard for compression of moving
images. On some DVDs digital audio has been
compressed and recorded in this format.
®
DivX
DivX® is a digital video compression technology based
on MPEG4 and developed by DivX, Inc.