Toshiba 2415 User Manual

Download

Satellite 2410/2415 Series User’s Guide

If you need assistance:

InTouch Calling within the United States (800) 457-7777 Calling from outside the United States (949) 859-4273

For more information, see Chapter 9 on page 214 in this guide.

Center

TOSHIBA

C6641-1202M1

Model: Satellite® 2410/2415 Series

Compact Disk-ReWritable

The computer system you purchased may include a Compact DiskReWritable (CD-RW), one of the most advanced storage technologies available. As with any new technology, you must read and follow all set-up and usage instructions in the applicable user guides and/or manuals enclosed. If you fail to do so, this product may not function properly and you may lose data or suffer other damage. TOSHIBA AMERICA

INFORMATION SYSTEMS (“TOSHIBA”), ITS AFFILIATES AND SUPPLIERS DO NOT WARRANT THAT OPERATION OF THE PRODUCT WILL BE UNINTERRUPTED OR ERROR FREE. YOU AGREE THAT TOSHIBA, ITS AFFILIATES AND SUPPLIERS SHALL HAVE NO RESPONSIBILITY FOR DAMAGE TO OR LOSS OF ANY BUSINESS, PROFITS, PROGRAMS, DATA OR REMOVABLE STORAGE MEDIA ARISING OUT OF OR RESULTING FROM THE USE OF THE PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY THEREOF.

Protection of Stored Data

For your important data, please make periodic back-up copies of all the data stored on the hard disk or other storage devices as a precaution against possible failures, alteration, or loss of the data. IF YOUR DATA IS

ALTERED OR LOST DUE TO ANY TROUBLE, FAILURE OR MALFUNCTION OF THE HARD DISK DRIVE OR OTHER STORAGE DEVICES AND THE DATA CANNOT BE RECOVERED, TOSHIBA SHALL NOT BE LIABLE FOR ANY DAMAGE OR LOSS OF DATA, OR ANY OTHER DAMAGE RESULTING THEREFROM. WHEN COPYING OR TRANSFERRING YOUR DATA, PLEASE BE SURE TO CONFIRM WHETHER THE DATA HAS BEEN SUCCESSFULLY COPIED OR TRANSFERRED. TOSHIBA DISCLAIMS ANY LIABILITY FOR THE FAILURE TO COPY OR TRANSFER THE DATA CORRECTLY.

Critical Applications

The computer you have purchased is not designed for any “critical applications.” “Critical applications” means life support systems, medical applications, connections to implanted medical devices, commercial transportation, nuclear facilities or systems or any other applications where product failure could lead to injury to persons or loss of life or catastrophic property damage. ACCORDINGLY, TOSHIBA, ITS AFFILIATES

AND SUPPLIERS DISCLAIM ANY AND ALL LIABILITY ARISING OUT OF THE USE OF THE COMPUTER PRODUCTS IN

ANY CRITICAL APPLICATIONS. IF YOU USE THE COMPUTER PRODUCTS IN A CRITICAL APPLICATION, YOU, AND NOT TOSHIBA, ASSUME FULL RESPONSIBILITY FOR SUCH USE.

FCC Notice

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

❖ Reorient or relocate the receiving antenna.

❖ Increase the separation between the equipment and receiver.

❖ Connect the equipment to an outlet on a circuit different from that to

which the receiver is connected.

❖ Consult the dealer or an experienced radio/TV technician for help.

NOTE: Only peripherals complying with the FCC Class B limits may be attached

to this equipment. Operation with noncompliant peripherals or peripherals not recommended by Toshiba is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer's or expansion unit’s serial port, parallel port, monitor port, USB port,

port, i.LINK® port and microphone jack. Changes or modifications made

PS/2 to this equipment not expressly approved by Toshiba or parties authorized by

Toshiba could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

❖ This device may not cause harmful interference.

❖ This device must accept any interference received, including

interference that may cause undesired operation.

Contact:

Toshiba America Information Systems, Inc. 9740 Irvine Blvd. Irvine, CA 92618-1697 (949) 583-3000

Industry Canada Requirement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conformé à la norme NMB-003 du Canada.

FCC Requirements

The following information is pursuant to FCC CFR 47, Part 68 and refers to internal modems.

Installation

When you are ready to install or use the modem, call your local telephone company and give them the following information:

❖ The telephone number of the line to which you will connect the

modem.

❖ The FCC registration number of the modem.

❖ The Ringer Equivalence Number (REN) of the modem, which is 0.6B.

The modem connects to the telephone line by means of a standard jack called the USOC RJ11C.

Type of Service

Your modem is designed to be used on standard-device telephone lines. Connection to telephone company-provided coin service (central office implemented systems) is prohibited. Connection to party lines service is subject to State tariffs. If you have any questions about your telephone line, such as how many pieces of equipment you can connect to it, the telephone company will provide this information upon request.

Telephone Company Procedures

The goal of the telephone company is to provide you with the best service it can. In order to do this, it may occasionally be necessary for them to make changes in their equipment, operations or procedures. If these changes might affect your service or the operation of your equipment, the telephone

company will give you notice, in writing, to allow you to make any changes necessary to maintain uninterrupted service.

If Problems Arise

If any of your telephone equipment is not operating properly, you should immediately remove it from your telephone line, as it may cause harm to the telephone network. If the telephone company notes a problem, they may temporarily discontinue service. When practical, they will notify you in advance of this disconnection. If advance notice is not feasible, you will be notified as soon as possible. When you are notified, you will be given the opportunity to correct the problem and informed of your right to file a complaint with the FCC. In the event repairs are ever needed on your modem, they should be performed by Toshiba Corporation, Toshiba America Information Systems, Inc. or an authorized representative of Toshi ba .

Disconnection

If you should ever decide to permanently disconnect your modem from its present line, please call the telephone company and let them know of this change.

Fax Branding

The Telephone Consumer Protection Act of 1991 makes it unlawful to use a computer or other electronic device to send any message via a telephone fax machine unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business, other entity or individual sending the message and the telephone number of the sending machine or such business, other entity or individual.

In order to program this information into your fax modem, you should complete the setup for your fax software before sending a message.

Instructions for IC CS-03 certified equipment

1 NOTICE: The Industry Canada label identifies certified equipment.

This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer should be

aware that compliance with the above conditions may not prevent degradation of service in some situations.

Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.

Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.

2 The user manual of analog equipment must contain the equipment’s

Ringer Equivalence Number (REN) and an explanation notice similar to the following:

The Ringer Equivalence Number (REN) of this device can be found on the label affixed to your computer.

NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.

3 The standard connecting arrangement (telephone jack type) for this

equipment is jack type(s): USOC RJ11C.

Wireless Interoperability

The Toshiba Wireless LAN Mini PCI Card products are designed to be interoperable with any wireless LAN product that is based on Direct Sequence Spread Spectrum (DSSS) radio technology, and is compliant to:

❖ The IEEE 802.11 Standard on Wireless LANs (Revision B), as

defined and approved by the Institute of Electrical and Electronics Engineers.

❖ The Wireless Fidelity (Wi-Fi

Wireless Ethernet Compatibility Alliance.

) certification as defined by the WECA

Wireless LAN and your Health

Wireless LAN products, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitted by Wireless LAN devices however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones. Because Wireless LAN products operate within the guidelines found in radio frequency safety standards and recommendations, Toshiba believes Wireless LAN is safe for use by consumers. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.

In some situations or environments, the use of Wireless LAN may be restricted by the proprietor of the building or responsible representatives of the organization. These situations may for example include:

❖ Using the Wireless LAN equipment on board of airplanes, or

❖ In any other environment where the risk of interference to other

devices or services is perceived or identified as harmful.

If you are uncertain of the policy that applies on the use of wireless devices in a specific organization or environment (e.g., airports), you are encouraged to ask for authorization to use the Wireless LAN device prior to turning on the equipment.

Regulatory Information

The Toshiba Wireless LAN Mini PCI Card must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product. This device complies with the following radio frequency and safety standards.

Canada – Industry Canada (IC)

This device complies with RSS 210 of Industry Canada.

Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device.

L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes: (1) il ne doit pas produire de brouillage et (2) l’utilisation du dispositif doit étre prét à accepter tout brouillage radioélectrique recu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.

To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.

Pour empêcher que cet appareil cause du brouillage au service faisant l'object d'une licence, il doit être utilisé à l 'interieur et devrait être placé loin des fenêtres afin de fournir un écran de blidage maximal. Si le matérial (ou son antenne d 'émission) est installé à l ' exterieur, il doit faire l'object d' une licence.

USA-Federal Communications Commission (FCC)

This device complies with Part 15 of FCC Rules. Operation of the devices in a Wireless LAN System is subject to the following two conditions:

❖ This device may not cause harmful interference.

❖ This device must accept any interference that may cause undesired

operation.

Caution: Exposure to Radio Frequency Radiation

The radiated output power of the Toshiba Wireless LAN Mini PCI Card is far below the FCC radio frequency exposure limits. Nevertheless, the Toshiba Wireless LAN Mini PCI Card shall be used in such a manner that the potential for human contact during normal operation is minimized. When using this device in combination with Wireless LAN Outdoor Antenna products, a certain separation distance between antenna and nearby persons has to be kept to ensure RF exposure compliance. The distance the user needs to be from the antennas, located on top of the LCD, should not be less than 20.0 cm when the display is raised to its normal operating position. Refer to the Regulatory Statements as identified in the documentation that comes with those products for additional information.

The Toshiba Wireless LAN Mini PCI Card is far below the FCC radio frequency exposure limits.

No other transmitter may be co-located with this device except FCC ID# CJ6PA3121BT.

Refer to the Regulatory Statements as identified in the documentation that comes with those products for additional information.

Nevertheless, it is advised to use the Toshiba Wireless LAN Mini PCI Card in such a manner that human contact during normal operation is minimized.

Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

❖ Reorient or relocate the receiving antenna.

❖ Increase the distance between the equipment and the receiver.

❖ Connect the equipment to an outlet on a circuit different from that to

which the receiver is connected.

❖ Consult the dealer or an experienced radio/TV technician for help.

Toshiba is not responsible for any radio or television interference caused by unauthorized modification of the devices included with this Toshiba Wireless LAN Mini PCI Card, or the substitution or attachment of connecting cables and equipment other than specified by Toshiba.

The correction of interference caused by such unauthorized modification, substitution or attachment will be the responsibility of the user.

Approved Countries for use

This equipment is approved to the radio standard by the countries in Fig.1.

Australia Austria Belgium

Canada Denmark Finland

France Germany Greece

Iceland Ireland Italy

Japan Luxembourg Mexico

Netherlands New Zealand Norway

Poland Portugal Spain

Sweden Switzerland UK

USA

Fig. 1.

Caution: Do not use this equipment except in the countries in Fig.1.

Caution: Bluetooth and Exposure to Radio Frequency Radiation

The radiated output power of the BluetoothTM Card from Toshiba is far below FCC radio frequency exposure limits. Nevertheless, the Bluetooth card shall be used in such a manner that the potential for human contact during normal operation is minimized. In order to comply with FCC radio frequency radiation exposure guidelines for an uncontrolled environment, the Bluetooth Card has to be operated with the user maintaining a minimum distance of 20 cm from the antennas located on top of the LCD when the display is raised to its normal operating position. Refer to the Regulatory Statements as identified in the documentation that comes with those products for additional information. No other transmitter may be colocated with this device except FCC ID# CJ6PA3070WL or CJ6PA3171WL.

CD-ROM, DVD-ROM, DVD-ROM/CD-RW, DVD-R/RW Safety Instructions

The CD-ROM, DVD-ROM, DVD-ROM/CD-RW and DVD-R/RW drives employ a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.

Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure.

To prevent direct exposure to the laser beam, do not try to open the enclosure.

Location of the required label

(Sample shown below. (Location of the label and manufacturing information may vary.)

CAUTION : This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep it for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” To prevent direct exposure to the laser beam, do not try to open the enclosure.

Use of controls or adjustments or performance of procedures other than those specified in the owner’s manual may result in hazardous radiation exposure.

This guide is copyrighted by Toshiba America Information Systems, Inc. with all rights reserved. Under the copyright laws, this guide cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed, however, with respect to the use of the information contained herein.

Export Administration Regulation

This document contains technical data that may be controlled under the U.S. Export Administration Regulations, and may be subject to the approval of the U.S. Department of Commerce prior to export. Any export, directly or indirectly, in contravention of the U.S. Export Administration Regulations is prohibited.

Notice

The information contained in this manual, including but not limited to any product specifications, is subject to change without notice.

TOSHIBA CORPORATION AND TOSHIBA AMERICA INFORMATION SYSTEMS, INC. (TOSHIBA) PROVIDES NO WARRANTY WITH REGARD TO THIS MANUAL OR ANY OTHER INFORMATION CONTAINED HEREIN AND HEREBY EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE WITH REGARD TO ANY OF THE FOREGOING. TOSHIBA ASSUMES NO LIABILITY FOR ANY DAMAGES INCURRED DIRECTLY OR INDIRECTLY FROM ANY TECHNICAL OR TYPOGRAPHICAL ERRORS OR OMISSIONS CONTAINED HEREIN OR FOR DISCREPANCIES BETWEEN THE PRODUCT AND THE MANUAL. IN NO EVENT SHALL TOSHIBA BE LIABLE FOR ANY INCIDENTAL,

CONSEQUENTIAL, SPECIAL, OR EXEMPLARY DAMAGES, WHETHER BASED ON TORT, CONTRACT OR OTHERWISE, ARISING OUT OF OR IN CONNECTION WITH THIS MANUAL OR ANY OTHER INFORMATION CONTAINED HEREIN OR THE USE THEREOF.

Trademarks

Satellite, Noteworthy, SelectServ, InTouch, and Fn-esse are registered trademarks of Toshiba America Information Systems, Inc. and/or Toshiba Corporation.

WinDVD is a trademark of InterVideo, Inc.

Microsoft, Windows, DirectX, and DirectShow are registered trademarks, and Windows Media is a trademark of Microsoft Corporation.

i.LINK is a registered trademark of Sony Corporation.

PS/2 is a registered trademark of IBM Corporation.

Wi-Fi is a trademark of the Wireless Capability Ethernet Alliance.

TouchPad is a trademark of Synaptics, Inc.

CompuServe is a registered trademark of America Online, Inc.

Bluetooth is a trademark owned by its proprietor and used by Toshiba under license.

All other brand and product names are trademarks or registered trademarks of their respective companies.

Computer Disposal Information

This product contains mercury. Disposal of this material may be regulated due to environmental considerations. For disposal, reuse or recycling information, please contact your local government or the Electronic Industries Alliance at www.eiae.org.

Introduction ..............................................................22

This guide .............................................................. 22

Safety icons ........................................................... 23

Other icons used.............................................. 24

Other documentation ............................................. 24

Service options ...................................................... 25

Chapter 1: Finding Your Way Around ........................ 26

Making sure you have everything .......................... 26

Front with the display closed ................................. 27

Back....................................................................... 28

Right side............................................................... 29

Left side ................................................................. 30

Front with the display open.................................... 31

Keyboard indicator lights ................................. 33

System indicator panel .................................... 34

CD/DVD control buttons .................................. 35

Underside .............................................................. 36

Chapter 2: Getting Started......................................... 38

Selecting a place to work ....................................... 38

Contents

Creating a computer-friendly environment....... 38

Keeping yourself comfortable .......................... 39

Precautions...................................................... 42

Setting up your computer ...................................... 43

Setting up your software.................................. 44

Registering your computer with Toshiba ......... 45

Adding external devices ................................... 45

Installing additional memory (optional) ................. 46

Connecting a mouse .............................................. 53

Connecting a printer .............................................. 53

Connecting a USB printer................................. 53

Connecting a parallel printer ............................ 53

Using external display devices ............................... 54

Connecting an external monitor ....................... 54

Directing the display output

when you turn on the computer................ 55

Adjusting the quality of the external display..... 55

Display limitations ........................................... 56

Connecting an external diskette drive..................... 57

Using an external keyboard.................................... 57

Connecting to a power source ............................... 58

Charging the battery .............................................. 60

Using the computer for the first time..................... 61

Opening the display panel................................ 61

Turning on the power....................................... 61

Activating the power-on password................... 63

Important information

on your computer’s built-in LCD sensor ... 64

Using the TouchPad......................................... 65

Primary and secondary control buttons........... 66

Disabling or enabling the TouchPad................. 66

Setting up a printer .......................................... 68

Setting up the fax function..................................... 70

Powering off the computer .................................... 72

Contents

Caring for your computer....................................... 72

Cleaning the computer..................................... 73

Moving the computer....................................... 73

Using a computer lock ..................................... 73

Chapter 3: Learning the Basics.................................. 75

Computing tips ...................................................... 75

Using the keyboard ................................................ 76

Character keys ................................................. 77

Ctrl, Fn, and Alt keys ........................................ 77

Function keys................................................... 77

Windows® special keys.................................... 78

Overlay keys..................................................... 78

Emulating a full-size keyboard ............................... 80

TOSHIBA Console button....................................... 80

Starting a program................................................. 81

Saving your work................................................... 81

Printing your work ................................................. 82

Using diskettes ...................................................... 83

Inserting and removing diskettes..................... 84

Caring for diskettes.......................................... 84

Backing up your files ............................................. 85

Copying to a diskette ....................................... 85

Playing a CD or DVD .............................................. 86

Drive components and control buttons............ 87

CD/DVD control buttons .................................. 88

CD/DVD and Digital audio modes .................... 89

Inserting a disc ................................................ 90

Playing an audio CD......................................... 92

Viewing the contents of a CD or DVD............... 94

Removing a disc with the computer on............ 95

Removing a disc with the computer off ........... 95

Caring for CDs and DVDs................................. 96

Using the DVD-ROM or multi-function drive.......... 96

Contents

Setting up for communications.............................. 97

Connecting the modem.................................... 97

Connecting your computer to a network.......... 98

Powering down the computer................................ 99

Turn Off or Shut down command..................... 99

Restart command .......................................... 100

Hibernation command ................................... 100

Standby command......................................... 101

Using Turn Off or Shut down ............................... 101

Turning off or shutting down more quickly .... 103

Starting again after Turn Off or Shut down .... 105

Using Hibernation ................................................ 105

Enabling the Hibernation command ............... 106

Going into Hibernation mode ......................... 107

Going into Hibernation mode more quickly.... 108

Starting again from Hibernation..................... 111

Using Standby ..................................................... 112

Going into Standby mode more quickly ......... 113

Starting again from Standby .......................... 116

Chapter 4: Mobile Computing ................................. 117

Toshiba's energy-saver design............................. 117

Running the computer on battery power ............. 117

Using additional batteries .............................. 118

Battery safety precautions.............................. 118

Maximizing battery life................................... 119

Charging batteries................................................ 121

Charging the main battery.............................. 121

Charging the RTC battery............................... 122

Monitoring battery power .................................... 122

Determining remaining battery power............ 123

Conserving battery power .............................. 124

What to do when the battery runs low ........... 124

Contents

Setting battery alarms.................................... 125

Changing the main battery ................................... 126

Removing the battery from the computer ...... 126

Removing the battery from the battery cover. 127

Inserting a charged battery ............................ 128

Disposing of used batteries safely ....................... 129

Traveling tips........................................................ 130

Chapter 5: Getting to Know the Windows® XP

Operating System.............................. 131

Lesson 1: Exploring the desktop.......................... 132

Finding your way around the desktop ............ 132

Windows® XP file system .............................. 134

Lesson 2: Using the TouchPad

and control buttons together ........................ 135

Lesson 3: Learning about the Internet ................. 139

Lesson 4: Creating a new document .................... 140

Lesson 5: Creating a new folder........................... 142

Lesson 6: Starting programs ............................... 143

Lesson 7: Resizing, repositioning,

and hiding windows...................................... 145

Using the taskbar........................................... 146

Minimizing and maximizing windows ............ 146

Resizing and moving windows....................... 147

Lesson 8: Closing programs ................................ 148

Lesson 9: Creating shortcuts ............................... 149

Creating a shortcut to the Calculator.............. 149

Creating a shortcut to the Character Map ...... 150

Lesson 10: Changing the screen saver................. 152

Lesson 11: Setting the date and time................... 154

Lesson 12: Removing objects from the desktop.. 155

Lesson 13: Using System Restore ....................... 157

Lesson 14: If I am lost, what do I do? ................. 158

Windows

XP Help and Support.................... 158

Contents

Using the Windows® XP tour ......................... 160

Lesson 15: Turning off your computer................. 161

Chapter 6: Exploring Your Options.......................... 162

Windows® XP special features............................. 162

Personalizing your desktop.................................. 163

Customizing the taskbar ................................ 163

Changing desktop and browsing style ........... 164

Personalizing individual windows .................. 165

Customizing window toolbars........................ 166

Displaying information about each folder....... 167

Using your computer at the office........................ 169

Exchanging data with another computer.............. 169

Setting up a direct cable connection .............. 169

Setting up for communications...................... 170

Connecting your computer to a network ....... 172

Accessing the wireless modules

using your system tray ........................... 173

An overview of using the Internet ........................ 173

The Internet ................................................... 174

The World Wide Web ..................................... 174

Internet Service Providers.............................. 174

Connecting to the Internet

using a telephone line ............................. 175

Surfing the Internet........................................ 175

Internet features............................................. 176

Uploading and downloading files

from the Internet..................................... 176

Toshiba’s online resources................................... 177

Exploring video features ...................................... 177

Viewing presentations

or DVD movies on your television........... 177

Playing DVDs ................................................. 178

Exploring audio features ...................................... 178

Contents

Recording sounds.......................................... 179

Using a microphone....................................... 179

Adjusting recording quality ............................ 180

Using external speakers or headphones......... 181

Using PC Cards.................................................... 182

PC Card supporting software ......................... 182

Inserting PC Cards......................................... 183

Removing PC Cards....................................... 184

Hot swapping................................................. 184

Chapter 7: Toshiba Utilities ..................................... 186

TOSHIBA Accessibility ......................................... 186

Fn-esse ................................................................ 187

Starting Fn-esse............................................. 188

Assigning a key to a program or document ... 189

Viewing existing key assignments ................. 191

Changing or removing

existing key assignments........................ 191

Hotkey utility........................................................ 191

TOSHIBA Console ................................................ 192

Customize Your Computer ............................. 193

Security.......................................................... 194

Power Management ....................................... 194

TOSHIBA Button Controls .............................. 197

Toshiba Hardware Setup ................................ 198

Chapter 8: Using WinDVDTM

with Your Computer ........................... 201

Playing DVDs ....................................................... 201

Using the WinDVD slider bar (location) ......... 203

Using the WinDVD control panel.......................... 203

Using the control panel playback buttons ...... 204

Maximizing the video window........................ 208

Using WinDVD advanced features........................ 209

Contents

Using playlists ..................................................... 209

Creating a Playlist .......................................... 210

Playing a Playlist............................................ 211

Getting Help ......................................................... 213

Exiting WinDVD ................................................... 213

Chapter 9: If Something Goes Wrong ..................... 214

Problems that are easy to fix ............................... 214

Problems when you turn on the computer........... 216

The Windows® operating system is not working . 217

Using Startup options to fix problems ........... 218

Internet problems .......................................... 219

The Windows® XP operating system

can help you ........................................... 219

Resolving a hardware conflict.............................. 220

A plan of action.............................................. 220

Resolving hardware conflicts on your own .... 221

Fixing a problem with Device Manager .......... 222

Memory module problems............................. 224

Power and the batteries ................................. 225

Keyboard problems........................................ 226

Display problems ........................................... 227

Disk drive problems....................................... 229

DVD-ROM or multi-function drive problems.. 231

Sound system problems ................................ 232

PC Card problems.......................................... 232

Printer problems............................................ 235

Modem problems........................................... 236

Develop good computing habits .......................... 237

If you need further assistance.............................. 238

Before you call ............................................... 238

Contacting Toshiba ........................................ 239

Other Toshiba Internet Web sites ........................ 240

Toshiba’s worldwide offices ................................. 241

Contents

Appendix A: Hot Keys.............................................. 244

Volume Mute........................................................ 244

Instant password security.................................... 245

Without a password....................................... 245

With a password ............................................ 245

Maintaining security

when the battery isn’t fully charged ........ 246

Power usage mode .............................................. 247

Standby mode...................................................... 248

Hibernation mode ................................................ 249

Display modes ..................................................... 250

Display brightness ............................................... 251

Disabling or enabling the TouchPad..................... 251

Keyboard hot keys .............................................. 251

Appendix B: Power Cable Connectors ..................... 252

USA and Canada ............................................ 252

United Kingdom ............................................. 252

Australia......................................................... 252

Europe ........................................................... 252

Glossary ..................................................................253

Index .......................................................................269

Introduction

Welcome to the world of powerful and portable multimedia computers! With your new Toshiba notebook computer, your access to information can accompany you wherever you go.

You will find that your Microsoft Professional operating system is already installed on your computer. It offers exciting features and easy Internet access.

This guide

This guide introduces the computer’s features. You can:

❖ Read the entire guide from beginning to end.

❖ Skim through and stop when a topic interests you.

❖ Use the table of contents and the index to find specific

information.

If you are new to computers, or have not used a notebook computer before, read through the first couple of chapters to familiarize yourself with the components of the computer and how to turn it on. After that, seek out whatever interests you most.

Windows® XP Home or XP

Safety icons

This manual contains safety instructions that must be observed in order to avoid potential hazards that could result in personal injuries, damage to your equipment, or loss of data. These safety cautions have been classified according to the seriousness of the risk, and the icons highlight these instructions as follows:

DANGER: This icon indicates the existence of a hazard that could result in death or serious bodily injury if the safety instruction is not observed.

WARNING: This icon indicates the existence of a hazard that could result in bodily injury if the safety instruction is not observed.

Introduction

Safety icons

CAUTION: This icon indicates the existence of a hazard that could result in damage to equipment or property if the safety instruction is not observed.

NOTE: This icon indicates information that relates to the safe operation of the equipment or related items.

Introduction

Service options

Introduction

Service options

Toshiba offers a full line of service options built around its SelectServ Toshiba's Web site at

If you have a problem or need to contact Toshiba, see “If

Something Goes Wrong” on page 214.

warranty programs. For more information, visit

toshiba.com.

Chapter 1

Finding Your Way Around

This chapter presents a “grand tour” of your notebook computer. It serves as a reference when you need to locate specific parts of the computer.

Making sure you have everything

Before doing anything else, consult the Quick Start card provided with your system to make sure you received everything. If any items are missing or damaged, notify your dealer immediately. For additional help, see “If you need

further assistance” on page 238.

Finding Your Way Around

Front with the display closed

Display

System indicator panel

Volume control dial

The lights on the system indicator panel provide information about various system functions. For a description, see “System indicator panel” on page 34.

The volume control dial lets you adjust the loudness of the system speakers.

The 3.5 mm headphone out lets you connect stereo headphones or other audio-output devices, such as external speakers. Connecting other devices automatically disables the internal speakers.

The 3.5 mm microphone in jack lets you connect an external monaural microphone.

The display latch keeps the display panel closed and locked. To open the display panel, slide the display latch to the right and raise the panel.

The CD/DVD control buttons allow you to play audio CDs when the computer is turned off. You can also use them to play CDs and DVDs with the computer turned on. For a description of these controls, see “CD/DVD control buttons”

on page 35.

Microphone in jack

Headphone out

CD/DVD control buttons

latch

Back

Finding Your Way Around

Back

LAN port

DC-IN

The DC-IN is where you plug in the AC adapter.

USB

ports

Video out

Parallel port RGB (monitor) port

Modem port

Ether

The LAN port lets you connect the computer to a local area network using an Ethernet link.

The USB (Universal Serial Bus) ports allow you to connect USB peripherals to your computer.

DEFINITION: USB is a peripheral expansion standard that supports a data-transfer rate of up to 12 Mbps for peripherals such as keyboards, pointing devices, and monitors. USB peripherals have a single standard for cabling and connectors. The USB standard allows hot swapping of peripherals.

The video out allows you to play DVD video on a projector or TV.

The parallel port allows you to connect a parallel printer.

The RGB (monitor) port allows you to connect an external monitor.

The modem port lets you use a RJ11 telephone cable to connect the modem directly to a standard telephone line. For more information, see “Connecting the modem” on page 97.

Right side

Finding Your Way Around

Right side

Diskette drive eject button

Diskette drive LED

drive

Diskette

Wireless antenna LED*

(*only functional for systems with Wi-FiTM)

DVD-ROM or multi-function

drive LED

Wireless antenna on-off switch*

DVD-ROM or multi-function drive (Sample Drive)

Manual

eject button

Eject button

The diskette drive LED (light-emitting diode) flashes when the diskette drive is in use.

The diskette drive allows diskettes to be accessed.

The wireless antenna LED glows when the wireless antenna is in use.

The diskette drive eject button enables you to remove diskettes from the drive.

Security lock slot

The wireless antenna on-off switch turns the computer’s wireless antenna on or off.

The DVD-ROM or multi-function drive enables you to play high-resolution, full-screen videos at up to 30 frames per second. You can also use it to install and run programs from application CD-ROMs and play audio CDs.

The DVD-ROM or multi-function drive LED flashes when the drive is in use.

The eject button opens the drive tray when the computer is turned on.

Finding Your Way Around

Left side

The manual eject button enables you to open the drive tray when the computer is off.

CAUTION: Never use a pencil to press the manual eject button. Pencil lead can break off inside the computer and damage it. Instead, use a slim object such as a straightened paper clip.

The security lock slot allows you to attach an optional PORT- Noteworthy for securing it to a large, heavy object such as your desk.

Left side

Cooling vents

The cooling vents prevent the computer’s central processing unit (CPU) from overheating so that it can continue to perform at its maximum speed.

The two stacked PC Card slots support up to two Type II PC Cards, or one Type III PC Card. See “Using PC Cards” on

page 182 for more information.

computer lock cable to your computer

PC Card slots

PC Card eject buttons

CAUTION: To prevent possible overheating of the CPU, make sure you don’t block the cooling vents.

Battery release latch

The PC Card eject buttons release PC Cards from the corresponding slots.

Finding Your Way Around

Front with the display open

The battery release latch secures the battery cover to the computer, preventing the battery from dislodging from the computer case.

Front with the display open

Internet button

Power button

Speaker

Function keys

TouchPad

LCD sensor

System indicator

panel

Headphone out

Microphone in jack

Volume control dial

Primar

CD/DVD control buttons

Secondary control button

control button

Screen

TOSHIBA

Console button

Keyboard indicator lights

Speaker

Keyboard

Palm rest

This section describes features that are revealed when you open the display panel. For features that are visible when the display panel is closed, see “Front with the display closed” on

page 27.

The Internet button turns on the computer and launches your default Internet browser.

The power button turns the computer on and off.

Finding Your Way Around

Front with the display open

The stereo speakers let you hear sounds, such as system alarms associated with your software, and music from DVDROMs and audio CDs.

The function keys, when used with the several different system functions. For more information, see

“Hot Keys” on page 244.

The TouchPad stroke of a finger. For more information, see “Using the

TouchPad” on page 65.

The built-in LCD sensor causes your computer to go into Hibernation mode when the panel is closed, if set to perform this function. For more information, see “Important

information on your computer’s built-in LCD sensor” on page 64.

The lights on the system indicator panel provide information about various system functions. For a description of these lights, see “System indicator panel” on page 34.

The volume control dial lets you adjust the loudness of the system speakers.

The 3.5 mm headphone out lets you connect stereo headphones or other audio-output devices, such as external speakers. Connecting other devices automatically disables the internal speakers.

The 3.5 mm microphone in jack lets you connect an external monaural microphone.

enables you to move the cursor with the

Fn key, activate

The primary control button, located below the TouchPad, acts like the primary button on a mouse.

The secondary control button, located below the TouchPad, acts like the secondary button on a mouse.

on page 35.

The front panel provides a palm rest to assist you in maintaining proper posture while using the computer.

The 85-key keyboard provides all the functionality of a fullsize keyboard. For more information, see “Using the

keyboard” on page 76.

The keyboard indicator lights provide information about various keyboard functions. For details, see “Keyboard

indicator lights” on page 33.

The TOSHIBA Console button allows quick access to various functions. See “TOSHIBA Console” on page 192.

The computer’s screen is a liquid crystal display (LCD) that provides clear, sharp images. For more information on your viewing options, see “Display modes” on page 250.

Keyboard indicator lights

Finding Your Way Around

Front with the display open

Cursor control mode light

Numeric mode light

Caps lock light

The cursor control mode light glows green when the cursor control overlay is on. When this light is on, pressing an overlay key moves the cursor in the direction of the arrow printed on the front of the key instead of typing the letter printed on the top of the key.

The numeric mode light glows green when the numeric overlay is on. When this light is on, pressing an overlay key

Finding Your Way Around

Front with the display open

types the number printed on the front of the key instead of typing the letter printed on the top of the key.

The caps lock light glows when the caps lock function is on.

For more information, see “Overlay keys” on page 78.

System indicator panel

On/off light

power

light

Battery

light

Hard disk

drive light

disc

Disk/

activity

light

The AC power li ght glows green when the computer is connected to an external power source.

The on/off light glows green when the computer is on. The light flashes amber when the computer is in Standby mode.

The battery light indicates the main battery’s current charge. It glows green when the battery is fully charged. It glows amber while the battery is being charged. It does not glow if the external power source is disconnected or if the battery is completely discharged. For more information on determining remaining battery power, see “Monitoring battery power” on

page 122.

The hard disk drive light flashes green while the hard disk drive is being accessed.

The disk/disc activity light flashes green when the diskette drive, the DVD-ROM or the multi-function drive is being accessed.

CAUTION: Never turn off the computer while any drive is in use. Doing so may damage the media in use and result in loss of data.

CD/DVD control buttons

The control buttons on the front of the computer are for playing CDs, DVDs and digital audio files. You can play audio CDs while the computer is turned off.

Finding Your Way Around

Front with the display open

Digital audio

mode

Next track

Play/pause

track

Stop/eject

CD/ DVD mode

The CD/DVD mode button allows you to play CDs or DVDs in the DVD-ROM or multi-function drive.

The Digital audio mode button allows you to play digital audio files.

The previous track button returns the disc player to the preceding track on the disc.

The play/pause button starts the disc player, or makes the disc player pause if it is currently playing.

The stop/eject button stops a disc that is currently playing. Press the button again to eject the disc.

Finding Your Way Around

Underside

The next track button causes the disc player to skip to the following track on the disc.

NOTE: If you have set a password for logging onto your system, your computer will start up and you will need to log on before being able to play a CD or DVD.

Underside

*Wi-Fi Mini PCI cover

*Wi-Fi Mini PCI module is optional

The Wi-Fi Mini-PCI cover secures a Wi-Fi Mini-PCI card for wireless networking (for systems with Wi-Fi). See

“Accessing the wireless modules using your system tray” on page 173.

The expansion memory slot cover protects the slots where you insert additional memory. See “Installing additional

memory (optional)” on page 46 for detailed information.

Expansion memory slot cover

Modem cover

Battery cover

Battery release latch

Hard disk drive cover

The modem cover protects the built-in modem.

Finding Your Way Around

Underside

The battery release latch secures the battery cover to the computer, preventing the battery from dislodging from the computer case.

The battery cover provides access to the battery module, which lets you use your computer when a standard electrical outlet is not available. For information about replacing the battery, see “Changing the main battery” on page 126.

The hard disk drive cover protects the computer’s hard disk drive.

Chapter 2

Getting Started

This chapter provides tips for working comfortably, describes how to connect components, and explains what to do the first time you use your notebook computer.

Selecting a place to work

Your computer is portable and designed to be used in a variety of circumstances and locations.

Creating a computer-friendly environment

Place the computer on a flat surface that is large enough for the computer and any other items you need to use, such as a printer. Leave enough space around the computer and other equipment to provide adequate ventilation and prevent overheating.

To keep your computer in prime operating condition, protect your work area from:

❖ Dust, moisture, and direct sunlight.

❖ Equipment that generates a strong electromagnetic field,

such as stereo speakers (other than speakers that are connected to the computer) or speakerphones.

❖ Rapid changes in temperature or humidity and sources of

temperature change, such as air conditioner vents or heaters.

❖ Extreme heat, cold, or humidity.

❖ Liquids and corrosive chemicals.

CAUTION: If you spill liquid into the computer, turn it off, unplug it from the AC power source, and let it dry out completely before turning it on again.

If the computer does not operate correctly after you turn it back on, contact a Toshiba authorized service provider.

Keeping yourself comfortable

Getting Started

Selecting a place to work

Strain and stress injuries are becoming more common as people spend more time using their computers. With a little care and proper use of the equipment, you can work comfortably throughout the day.

This section provides hints on avoiding strain and stress injuries. For more information, consult books on ergonomics, repetitive-strain injury, and repetitive-stress syndrome.

Placement of the computer

Proper placement of the computer and external devices is important to avoid stress-related injuries.

❖ Place the computer on a flat surface at a comfortable

height and distance. You should be able to type without twisting your torso or neck, and look at the screen without slouching.

Getting Started

Selecting a place to work

❖ If you are using an external monitor, the top of the

display should be no higher than eye level.

❖ If you use a paper holder, set it at about the same height

and distance as the screen.

Seating and posture

When using your computer, maintain good posture with your body relaxed and your weight distributed evenly. Proper seating is a primary factor in reducing work strain. Some people find a backless chair more comfortable than a conventional chair.

Below eye level

Approximately 90-degree angles

Footrest

Correct posture and positioning of the computer

Whichever type you choose, use the following guidelines to adjust your chair for maximum computing comfort.

❖ Position your chair so that the keyboard is at or slightly

below the level of your elbow. You should be able to type comfortably with your shoulders relaxed and your forearms parallel to the floor.

If you are using a conventional chair:

❖ Your knees should be slightly higher than your hips. If

necessary, use a footrest to raise the level of your knees and ease the pressure on the back of your thighs.

Getting Started

Selecting a place to work

❖ Adjust the back of your chair so that it supports the lower

curve of your spine. If necessary, use a cushion to provide extra back support. Lower-back-support cushions are available at many office supply stores.

❖ Sit with your back straight so that your knees, hips, and

elbows form approximately 90-degree angles when you work. Do not slump forward or lean back too far.

Lighting

Proper lighting can improve the visibility of the display and reduce eyestrain.

❖ Position the display panel or external monitor so that

sunlight or bright indoor lighting does not reflect off the screen. Use tinted windows or shades to reduce glare.

❖ Avoid placing your computer in front of a bright light

that could shine directly in your eyes.

❖ If possible, use soft, indirect lighting in your computer

work area.

Arms and wrists

❖ Avoid bending, arching, or twisting your wrists. Keep

them in a relaxed, neutral position while typing.

❖ Exercise your hands, wrists, and arms to improve

circulation.

WARNING: Using the computer keyboard incorrectly may result in discomfort and possible injury. If your hands, wrists, and/or arms bother you while typing, stop using the computer and rest. If the discomfort persists, consult a physician.

Work habits

The key to avoiding discomfort or injury from strain is to vary your activities. If possible, schedule a variety of tasks into your working day. Finding ways to break up the routine can reduce stress and improve your efficiency.

❖ Take frequent breaks to change position, stretch your

❖ Avoid performing repetitive activities for long periods.

❖ Focusing your eyes on your computer screen for long

Precautions

Getting Started

Selecting a place to work

muscles, and relieve your eyes. A break of two or three minutes every half-hour is more effective than a long break after several hours.

Intersperse such activities with other tasks.

periods can cause eyestrain. Look away from the computer frequently and focus your eyes on a distant object for at least 30 seconds.

Your notebook computer is designed to provide optimum safety and ease of use, and to withstand the rigors of travel. You should observe certain precautions to further reduce the risk of personal injury or damage to the computer.

❖ Avoid prolonged physical contact with the underside of

the computer.

If the computer is used for long periods, its case can become very warm. While the temperature may not feel too hot to the touch, if you maintain physical contact with the computer for a long time (if you rest the computer on your lap, for example), your skin might suffer low-heat injury.

❖ Never apply heavy pressure to the computer or subject it

to sharp impacts. Excessive pressure or impact can damage computer components or otherwise cause your computer to malfunction.

Getting Started

Setting up your computer

❖ Some PC Cards can become hot with prolonged use. If

two cards are installed, both can become hot even if only one is being used. Overheating of a PC Card can result in errors or instability in its operation.

Be careful when you remove a PC Card that has been used for a long period.

❖ Avoid spilling liquids into the computer’s keyboard.

If you do spill a liquid that gets into the keyboard, turn off the computer immediately. Leave the computer turned off overnight to let it dry out before you use it again.

❖ Never turn off the computer if a drive-in-use light

indicates a drive is active.

Turning off the computer while it is reading from or writing to a disk may damage the disk, the drive, or both.

❖ Keep the computer and disks away from objects that

generate strong magnetic fields, such as large stereo speakers.

Information on diskettes is stored magnetically. Placing a magnet too close to a diskette can erase important files.

❖ Scan all new files for viruses.

This precaution is especially important for files you receive via diskette, CD-ROM or DVD discs, email, or download from the Internet. Occasionally, even new programs you buy from a supplier may contain a computer virus. You’ll need a special program to check for viruses. Ask your dealer or network administrator to help you.

Setting up your computer

Your computer contains a rechargeable high-capacity battery that needs to be charged before you can use it.

Getting Started

Setting up your computer

To use external power or to charge the battery, you must attach the AC adapter. See “Connecting to a power source”

on page 58.

Setting up your software

NOTE: The names of windows displayed and the order in which windows appear may vary depending on your software setup choices.

The first time you turn on your computer, the Setup Wizard guides you through steps to set up your software.

1 From the welcome screen, click Next to enter the Setup

Wizard.

2 Confirm acceptance of Microsoft’s End User License

Agreement and click Next.

3 Enter the computer name and description and click Next

or Skip.

The computer will pause for a moment while checking for an internet connection.

A window will display the message: “An Internet connection could not be chosen.”

4 Click Skip to exit the process or Next to continue.

NOTE: To register online, your computer’s modem must be connected to a voice-grade telephone line.

A window will display asking if you wish to register with Toshiba and Microsoft.

Getting Started

Setting up your computer

5 Click Ye s to register, or No to exit the process.

NOTE: If you click No, you may register with Toshiba by clicking the Register with Toshiba icon on the desktop.

6 Enter your personal information in the registration

window.

7 Click Finish to complete the process.

Your computer restarts automatically.

Registering your computer with Toshiba

Registering your computer lets Toshiba keep you up-to-date with information about new products and upgrades, and also extends your Toshiba warranty worldwide at no charge to you. You can register your computer with Toshiba by doubleclicking the icon on your desktop or by mailing the registration card that may ship with your computer.

NOTE: To register online, your computer’s modem must be connected to a voice-grade telephone line.

Adding external devices

NOTE: Before adding external devices, Toshiba recommends setting up your software first. See “Setting up your software” on

page 44.

Before starting to use your computer, you may also want to:

❖ Add more memory (see “Installing additional memory

(optional)” on page 46)

❖ Connect a mouse (see “Connecting a mouse” on page 53)

Getting Started

Installing additional memory (optional)

❖ Connect a full-size keyboard (see “Using an external

keyboard” on page 57)

❖ Connect an external monitor (see “Using external display

devices” on page 54)

❖ Connect a local printer (see “Connecting a printer” on

page 53)

❖ Install PC Cards (see “Using PC Cards” on page 182)

Installing additional memory (optional)

CAUTION: Before you install or remove a memory module, turn off the computer using the Start menu. If you install or remove a memory module while the computer is in Standby or Hibernation mode, data will be lost.

Your computer comes with enough memory to run most of today’s popular applications. You may want to increase the computer’s memory if you use complex software or process large amounts of data.

There are two memory slots. Your system may have both slots occupied.

CAUTION: If you use the computer for a long time, the memory modules will become hot. If this happens, let the modules cool to room temperature before you replace them.

Getting Started

Installing additional memory (optional)

CAUTION: Do not try to install a memory module under the following conditions. You can damage the computer and the module.

1. The computer is turned on.

2. The computer was shut down using Standby mode.

3. Power to the DVD-ROM or multi-function drive has been turned on.

CAUTION: Do not install or remove a memory module while the DVD-ROM or multi-function drive power is on.

1 If the computer is on, turn it off.

See “Turn Off or Shut down command” on page 99.

2 Unplug and remove any cables connected to the

computer.

3 Close the display panel and turn the computer upside

down.

Getting Started

Installing additional memory (optional)

Expansion memory slot cover

Underside of the computer

NOTE: Use a point size 0 Phillips screwdriver.

4 Locate the expansion memory slot cover and remove the

screw that secures the cover.

Removing the expansion memory slot cover screw

Getting Started

Installing additional memory (optional)

5 Using your finger or a narrow object, lift off the cover.

6 Put the screw and the cover in a safe place so that you can

retrieve them later.

CAUTION: Static electricity can damage the memory module. Before you handle the module, touch a grounded metal surface to discharge any static electricity you may have built up.

To avoid damaging the memory module, be careful not to touch its gold connector bar (on the side you insert into the computer).

7 Remove the new memory module from its antistatic

packaging.

8 Holding the memory module by its edges so that the gold

connector bar faces the slot, fit the module into the slot at a slight angle.

9 Gently press down on the memory module connector

until the clips snap into place.

Do not force the module into position. The memory module should be level when secured in place.

Getting Started

Installing additional memory (optional)

Inserting the memory module

CAUTION: Avoid touching the connectors on the memory module or on the computer. Grease or dust on the connectors may cause memory access problems.

10 Replace the memory slot cover.

11 Replace the screw and tighten it.

12 Turn the computer over and reconnect any cables you

removed.

You can now continue setting up the computer. When the operating system has loaded, you can verify that the computer has recognized the additional memory.

If you are adding extra memory after setting up the computer, verify that the computer has recognized it correctly as described in “Checking total memory” on page 52.

Getting Started

Installing additional memory (optional)

Removing a memory module

CAUTION: If you use the computer for a long time, the memory modules will become hot. If this happens, let the modules cool to room temperature before you replace them.

1 Follow steps 1 through 6 in “Installing additional

memory (optional)” on page 46.

CAUTIONS: Do not try to remove a memory module with the computer turned on. You can damage the computer and the device.

Do not remove the memory module while the computer is in Standby mode. The computer could hang up the next time you turn it on and data in memory will be lost. In either of the above cases, the Standby configuration will not be saved.

The following message appears when you turn on the power:

Warning: Resume Failure Press Any Key To Continue

If the computer hangs up when you turn it on, perform the following: Press the power button and hold it down for five seconds, then turn the power on again.

2 Push the latches to the outside to release the module. A

spring will force one end of the module up.

Getting Started

Installing additional memory (optional)

Removing the memory module

3 Gently pull the module out.

CAUTION: Avoid touching the connectors on the memory module or on the computer. Grease or dust on the connectors may cause memory access problems.

4 Complete the procedure by following steps 10 through 12

in “Installing additional memory (optional)” on page 46.

Checking total memory

When you add or remove memory, you can check that the computer has recognized the change. To do this:

1 Click Start, Control Panel

2 Click Performance and Maintenance.

3 Click System.

4 The General tab view automatically appears and shows

the recognized memory.

5 If the computer does not recognize the memory

configuration, turn off the computer, remove the memory slot cover, and make sure the memory module is seated

properly, as described in steps 8 and 9 of “Installing

additional memory (optional)” on page 46.

Connecting a mouse

You may want to use a mouse instead of the TouchPad, the computer’s built-in pointing device.

To connect a mouse, plug the mouse cable into one of the computer’s USB ports. You can connect it after you turn on the computer.

The operating system automatically detects the mouse. The mouse and TouchPad can be used at the same time.

Connecting a printer

You can connect a USB-compatible printer to your computer through the USB ports. You can connect a USB printer after you turn on the computer.

Getting Started

Connecting a mouse

Alternatively, you can connect a parallel printer to the computer’s parallel port.

Connecting a USB printer

To achieve the connection, you need a suitable USB cable, which may come with your printer. Otherwise, you can purchase one from a computer or electronics store.

NOTE: Follow the manufacturer’s instructions for connecting a USB printer to your computer.

Connecting a parallel printer

To achieve the connection, you need a suitable cable, which may come with your parallel printer. Otherwise, you can purchase one from a computer or electronics store.

Getting Started

Using external display devices

Connect a parallel printer before you turn on the computer.

NOTE: Follow the manufacturer’s instructions for connecting a parallel printer to your computer.

Using external display devices

Your computer comes with a built-in LCD display, but you can easily attach an external monitor or television to your computer if you need a larger screen.

Once you’ve connected an external display device, you can choose to use the internal display only, the external device only, or both simultaneously.

Connecting an external monitor is described below. For details of connecting other external video devices and setting display options, see “Exploring video features” on page 177.

For information on attaching a television to your computer, see “Viewing presentations or DVD movies on your

television” on page 177.

Connecting an external monitor

You must attach the monitor before you turn on the computer.

1 Connect the monitor’s video cable to the RGB (monitor)

port.

2 Connect the monitor’s power cable to a live electrical

outlet.

3 Turn on the external monitor.

4 Turn on the computer.

5 Set the display mode by pressing

Display Properties settings.

Fn + F5, or by setting the

Getting Started

Using external display devices

Directing the display output when you turn on the computer

Once you’ve connected an external display device, you can choose to use the internal display only, the external device only, or both simultaneously. The quickest way to change the display output settings is to use the display hot key (

Fn + F5).

1 While holding down

setting you want takes effect.

This hot key cycles through the display output settings in the following order:

❖ Built-in display panel only

❖ Built-in display panel and external monitor

simultaneously

❖ External monitor only

❖ Built-in display panel and external video device

simultaneously

❖ Other external video device only

2 Release the

TECHNICAL NOTE: You can also change these settings using the Display Properties box in the Control Panel.

Fn key.

Fn, press F5 repeatedly until the

Adjusting the quality of the external display

To obtain the best picture quality from your external display device, you may need to adjust the video settings. See the

Getting Started

Using external display devices

documentation supplied with the device for additional configuration steps.

TECHNICAL NOTE: In order to use the simultaneous mode, you must set the resolution of the internal display panel to match the resolution of the external display device. The external display device must support a resolution of 640 X 480 or higher.

Display limitations

Keep in mind that the quality of the display will be limited to the capabilities of the external video device.

❖ If the external video device, such as an SVGA monitor, is

capable of displaying at a maximum resolution of 640 x 480 and your system is set for a higher resolution, only part of the desktop will appear on the screen. You can view the “lost” area by scrolling to it.

❖ If you use the display hot key (Fn + F5) to change the

display output with the LCD Display Stretch option enabled and the Display area (resolution) set to 640 x 480 or 800 x 600, the image on the internal display panel may appear stretched.

NOTE: The Windows® XP operating system by default does not display resolutions below 800 x 600. To display the 640 x 480 resolution, you may need to click the Settings tab in the Display Properties window, click Advanced, click the Adapter tab, click List all modes.

Getting Started

Connecting an external diskette drive

Although your computer has an internal diskette drive, you can attach an external USB diskette drive to use diskettes with your computer. These drives hold 3.5-inch diskettes.

Sample external USB diskette drive

To connect an external USB diskette drive, connect the drive’s cable to one of the computer’s USB ports.

For more information about diskettes, see “Using diskettes”

on page 83.

Using an external keyboard

If you prefer to use a full-size keyboard, you can attach one to your computer provided that the keyboard is USBcompatible.

To connect a keyboard, attach its cable to one of the computer’s USB ports. You can do this after you turn on the computer.

NOTE: The Fn emulation key is not supported when using a USB keyboard.

Getting Started

Connecting to a power source

Your computer requires power to operate. Use the power cable and AC adapter to connect the computer to a live electrical outlet, or to charge the computer’s battery.

Power cable

AC adapter

Power cable and AC adapter

CAUTION: Use only the AC adapter supplied with your computer or an equivalent adapter that is compatible. Use of any incompatible adapter could damage your computer. Toshiba assumes no liability for any damage caused by use of an incompatible adapter.

When you connect the AC adapter to the computer, always follow the steps in the exact order as described in the User's Manual. Connecting the power cable to a live electrical outlet should be the last step otherwise the adapter DC output plug could hold an electrical charge and cause an electrical shock or minor bodily injury when touched. As a general safety precaution, avoid touching any metal parts.

DANGER: Hold the power cable by its plug when you connect/ disconnect it. Do NOT pull the cable itself. Doing so may damage the power cable and result in a short circuit or electric shock.

To connect AC power to the computer:

1 Connect the power cable to the AC adapter.

Getting Started

Connecting to a power source

Connecting the power cable to the AC adapter

2 Plug the AC adapter into the DC-IN on the back of the

computer.

Connecting the AC adapter to the computer

3 Connect the power cable to a live electrical outlet.

If the electrical outlet is live, the system indicator panel’s AC power light ( ) glows green.

Getting Started

Charging the battery

DANGER: Damaged power cables can cause fire or electric shock. Never modify, forcibly bend, place heavy objects on top of, or apply heat to the power cable.

If the power cable becomes damaged or the plug overheats, discontinue use. There is a risk of electric shock.

Never remove the power plug from the outlet with wet hands. Doing so may cause an electric shock.

Charging the battery

Before you can use the battery to power the computer, you must charge it. Connect the computer to a live power outlet using the AC adapter and power cable. The AC power light glows green and the battery light glows amber to show that it is charging.

Once the computer is connected to a power outlet, you can charge the battery with the computer turned off or on. It takes several hours to charge the battery when the computer is off. It takes much longer to charge the battery when the computer is on. The less power the computer is consuming, the faster the battery will charge.

For more information on battery use, see “Running the

computer on battery power” on page 117.

CAUTION: Once the battery is charged for the first time, avoid leaving the computer plugged in and turned off for more than a few hours at a time. Continuing to charge a fully charged battery can damage the battery.

Getting Started

Using the computer for the first time

Opening the display panel

Slide the display latch to the right and lift the display panel.

Lift

Slide

Opening the display panel

CAUTION: To avoid damaging the display panel, don’t force it beyond the point where it moves easily.

Never lift or move the computer using the display panel.

Turning on the power

1 Check that all the drives are empty.

2 Turn on the computer by pressing the power button,

located above the keyboard, until the on/off light changes to green.

Getting Started

Using the computer for the first time

Pressing the power button

NOTE: When you turn on the computer for the first time, don’t turn off the power again until the operating system has loaded completely.

The AC power light on your computer will glow when the computer is connected to an external power source.

The battery light:

❖ Glows amber while the battery is being charged.

❖ Glows green when the battery is fully charged.

❖ Is unlit when the computer is not connected to an

external power source. For information on determining battery power, see “Monitoring battery

power” on page 122.

The hard disk drive light flashes to indicate that the hard disk drive is currently in use.

CAUTION: Never turn off the computer while any drive is in use.

Using the computer for the first time

Activating the power-on password

When you first turn on your computer, no password is required. But you can set up your computer so that a password is required to complete the powering up process in the future.

To activate the power-on password:

1 Press the TOSHIBA Console button.

The TOSHIBA Console window appears. For more information see “TOSHIBA Console” on page 192.

2 Click Security.

3 Click User password.

4 Follow the on-screen instructions.

The password requirement becomes active the next time you turn on your computer.

When the feature is active, you must enter the password during the power-on process. After typing your password, press the

Enter key.

Getting Started

If the password is correct, the power-on process continues. If the password is incorrect, you will be prompted to try again.

NOTE: If you forget your power-on password and therefore can’t turn on your computer, take your computer to a Toshiba authorized service center for help.

After the third incorrect password submission, the system automatically shuts down.

Getting Started

Using the computer for the first time

Important information on your computer’s built-in LCD sensor

Your computer has a built-in LCD (liquid crystal display) sensor located near the left-hand corner of the palm rest. When the computer is on, the LCD sensor detects when the display panel is closed.

Built-in LCD sensor

Your computer’s Power Saver default setting when the display panel is closed is Hibernation mode. When you close the display panel with that setting, the built-in LCD sensor causes your computer to go into Hibernation mode. (See

“Using Hibernation” on page 105.)

Please do not place a magnetic object in the area of the lefthand corner of the palm rest. A magnetic object placed there causes the LCD sensor to erroneously activate.

If your computer is set to enter Hibernation mode when the display panel is closed, the presence of a magnetic object in the area of the left-hand corner of the palm rest can cause

your computer to go into Hibernation mode even if your display panel is open.

NOTE: To start the computer again from Hibernation mode, move the magnetic object away from the computer, then see “Starting

again from Hibernation” on page 111.

If your computer is set for “no action” when the display panel is closed, a magnetic object in the area of the front-left corner of the computer can cause the display panel screen to go blank. Moving the magnetic object away reactivates the screen.

Using the TouchPad

The TouchPad, the small, smooth square cutout located in front of the keyboard, is sensitive to touch and enables you to move the cursor with the stroke of a finger. Simply move your finger on the TouchPad in the direction you’d like to move the cursor:

Getting Started

Using the computer for the first time

❖ To move the cursor to the top of the page, slide your

finger forward on the TouchPad.

❖ To move the cursor to the bottom of the page, slide your

finger toward yourself.

❖ To move the cursor to the right side of the page, slide

your finger across the TouchPad from left to right.

❖ To move it to the left side, slide your finger from right to

left.

NOTE: Because the TouchPad is much smaller than the display screen, moving your cursor across the screen often means having to move your finger several times across the TouchPad in the preferred direction.

Getting Started

Using the computer for the first time

Once you’ve positioned your cursor, you can select an object on the display screen by double-tapping the TouchPad or clicking the control buttons.

For more on the TouchPad, see “Lesson 2: Using the

TouchPad and control buttons together” on page 135.

You can disable or enable the TouchPad. See “Disabling or

enabling the TouchPad” on page 66.

Primary and secondary control buttons

The control buttons are below the TouchPad and are used like the buttons on a mouse. The primary control button is the button on the left and corresponds to the left mouse button. To double-click, press the primary button twice in rapid succession.

The secondary control button is the button on the right and corresponds to the right mouse button. Check your program’s documentation to find whether it uses the secondary mouse button.

For more on the primary and secondary control buttons, see

“Lesson 2: Using the TouchPad and control buttons together” on page 135.

Disabling or enabling the TouchPad

The TouchPad is enabled by default. To change the enable/ disable TouchPad setting:

1 Click Start, Control Panel.

The Control Panel window appears.

2 Click Printers and Other Hardware.

3 Click the Mouse icon.

4 Click the TouchPAD ON/OFF tab.

The TouchPAD ON/OFF tab view window appears.

Using the computer for the first time

Sample Mouse Properties window

Getting Started

5 Select Disable or Enable, whichever is appropriate.

6 Click Apply.

7 Click OK.

The Mouse Properties window closes.

8 Close the Printers and Other Hardware window.

9 Close the Control Panel window.

You can also use a hot key to disable or enable the TouchPad. See “Disabling or enabling the TouchPad” on page 251.

Getting Started

Using the computer for the first time

Setting up a printer

NOTE: Follow the manufacturer’s instructions for connecting a printer to your computer.

If your printer has not been detected automatically when connected to the computer, you must install the printer driver for the model of printer that is connected to your computer. You install the printer driver either by following the instructions indicated in your printer guide, or by using the operating system’s Add Printer Wizard.

If you plan to set up a printer later, close or cancel the Add Printer Wizard.

Using the Add Printer Wizard

The Add Printer Wizard may be needed by older printers or printers shared on a network.

To set up a printer with the Add Printer Wizard:

1 Click Start, Control Panel.

The Control Panel appears.

Getting Started

Using the computer for the first time

Sample Control Panel

2 Click Printers and Other Hardware.

3 Click the Printers and Faxes icon.

The Printers and Faxes window appears.

Sample Printers and Faxes window

Getting Started

Setting up the fax function

4 Click Add a printer.

The Add Printer Wizard window appears.

Sample Add Printer Wizard

5 Follow the on-screen instructions.

HINT: If you are using more than one printer, make sure the name is descriptive enough to help you tell the difference.

Setting up the fax function

To set up the fax capability:

1 Click Start, Printers and Faxes.

The Printers and Faxes window appears.

Getting Started

Setting up the fax function

2 Click the Set up faxing option.

3 Follow the on-screen instructions.

The fax function default setting is enabled. If it is disabled, enable the fax function by doing the following:

1 Click Start, Printers and Faxes.

2 Right-click the fax icon.

3 Click Properties from the drop-down menu.

4 Click the Devices tab.

5 Click Properties.

6 Click the Receive tab.

7 Click Enable device to receive.

To disable the auto-receive function, repeat steps 1-4. But, under the device name, right-click Toshiba Soft Modem AMR, select Receive and then select Disable.

Getting Started

Powering off the computer

It’s a good idea to power off your computer when you are not using it for a while.

If you are using the computer for the first time, leave the computer plugged into a power source (even though the computer is off) to fully charge the main battery. When the main battery light glows green, the battery is fully charged.

Guidelines for powering off the computer:

❖ If you have work in progress and if you are not connected

to a network, use the Hibernate command to save your system settings to the hard disk so that, when you turn on the computer again, you automatically return to where you left off.

❖ To leave the computer off for a longer period, power

down the computer. The Windows uses the Shut down command to power down the computer if you are connected to a Windows server (domain server) or the Turn Off command if you are not.

❖ When the hard disk drive light on the system indicator

panel is on, don’t turn off the power. Doing so may damage your hard disk.

For more information, see “Powering down the computer” on

page 99.

Caring for your computer

This section gives tips on cleaning and moving your computer, and explains how to fit an antitheft lock. For information about taking care of your computer’s battery, see

“Running the computer on battery power” on page 117.

XP operating system

network

Cleaning the computer

To keep your computer clean, gently wipe the display panel and exterior case with a lightly dampened cloth. Ask your Toshiba dealer or network administrator for suggestions for appropriate cleaning products.

CAUTION: Keep liquid, including cleaning fluid, out of the computer’s keyboard, speaker grille, and other openings. Never spray cleaner directly onto the computer. Never use harsh or caustic chemical products to clean the computer.

Moving the computer

Before moving your computer, even across the room, make sure all disk activity has ended (the drive-in-use lights stop flashing) and all external peripheral cables are disconnected.

Getting Started

Caring for your computer

CAUTION: Never pick up the computer by its display panel or by the back (where the ports are located).

Although your notebook computer is built to withstand reasonable shock and vibration, transport it in a carrying case for long trips. You can purchase a carrying case from your Toshiba dealer or through Toshiba’s Web site at

Using a computer lock

You may want to secure your computer to a heavy object such as your desk. The easiest way to do this is to purchase an optional PORT-Noteworthy computer lock cable.

toshiba.com.

Getting Started

Caring for your computer

PORT-Noteworthy computer lock cable

To secure the computer:

1 Loop the cable through or around some part of a heavy

object.

Make sure there is no way for a potential thief to slip the cable off the object.

2 Pass the locking end through the loop.

3 Insert the cable’s locking end into the security lock slot

located on the right side of the computer, then rotate the key a quarter turn and remove it.

The computer is now securely locked to deter computer theft.

Sample locking the computer

Chapter 3

Learning the Basics

This chapter lists some computing tips and provides important information about basic features.

Computing tips

❖ Save your work frequently.

Your work stays in the computer’s temporary memory until you save it to the disk. You will lose all unsaved work, if, for example, a system error occurs and you must restart your computer, or your battery runs out of charge while you are working. Your computer can be configured to warn you when the battery is running low. See “Setting

battery alarms” on page 125.

HINT: Some programs have an automatic save feature that you can turn on. This feature saves your file to the hard disk at preset intervals. See your software documentation for details.

Learning the Basics

Using the keyboard

❖ Back up your files to diskettes (or other removable

storage media) on a regular basis. Label the backup copies clearly and store them in a safe place.

If your hard disk suddenly fails, you may lose all the data on it unless you have a separate backup copy.

❖ Use Disk Defragmenter to conserve disk space and help

your computer perform at its optimal level.

❖ Before turning off the computer, always use the Turn Off

or Shut down command (unless you want to use Standby or Hibernation mode as described in “Powering down the

computer” on page 99).

CAUTION: The operating system records information, such as your desktop setup, during its turn-off procedure. If you don’t let it turn off normally, details such as new icon positions may be lost.

Using the keyboard

Function keys

Alt (Alternate) key Fn key Ctrl (Control) key

Parts of the keyboard

Home

End PgDn

PgUp

Ins

Character keys

Windows

∗

Del

keys

Character keys

Typing with the character keys is very much like typing on a typewriter, except that:

❖ The spacebar creates a space character instead of just

passing over an area of the page.

❖ The lowercase l (el) and the number 1 are not

interchangeable.

❖ The uppercase letter O and the number 0 are not

interchangeable.

❖ The Caps Lock key changes only the alphabet keys to upper

case — the number and symbol keys are not affected.

Ctrl, Fn, and Alt keys

Alt

Ctrl

Ctrl, Fn and Alt keys

Learning the Basics

Using the keyboard

Ctrl, Fn, and Alt keys do different things depending on the

The program you are using. For more information, see your program documentation.

Function keys

The function keys (not to be confused with the Fn key) are the 12 keys at the top of the keyboard.

Function keys

F1 through F12 are called function keys because they run

programmed functions when you press them. Used in combination with the run specific functions on the computer.

Fn key, function keys marked with icons

Learning the Basics

Using the keyboard

Windows® special keys

The keyboard provides two keys that have special functions in the operating system:

❖ The Windows

❖ The Application key has the same function as the

secondary (or right mouse) control button.

Overlay keys

790

Home PgUp

78 9

UI OP

Application key

Windows® logo key

logo key opens the Start menu.

()&

∗

456

JKL

End PgDn

12 3

Ins Del

∗

: ;

Sample keyboard overlay keys

The keys with numbers and symbols on the front of them form the numeric and cursor overlay. This overlay lets you enter numeric data or control the cursor as you would using the ten-key keypad on a desktop computer’s keyboard.

Learning the Basics

Using the keyboard

Using the numeric keypad overlay

To turn on the numeric keypad overlay, press Fn and F11 simultaneously. The numeric mode keyboard indicator light glows when the numeric overlay is on.

You can still use the overlay keys to type alphabetic characters while the numeric overlay is on. To do so:

❖ For lowercase letters, hold down Fn while you type the

letters.

❖ For uppercase letters, hold down both Fn and Shift while

you type the letters.

To use the cursor control overlay when the numeric overlay is on, press and hold down keys. To return to the numeric overlay, release

Shift while you use the cursor control

Shift.

To turn off the numeric keypad overlay, hold down the and press

F11 again. The numeric mode light goes out.

Fn key

Using the cursor control overlay

To turn on the cursor control overlay, press Fn and F10 simultaneously. The cursor control mode keyboard indicator light glows when the cursor control overlay is on.

To type alphabetic characters while the overlay is on:

❖ For lowercase letters, hold down Fn while you type the

letters.

❖ For uppercase letters, hold down both Fn and Shift while

you type the letters.

To use the numeric keypad overlay when the cursor control overlay is on, hold down overlay keys. To return to the cursor control overlay, release

Shift.

To turn off the cursor control overlay, hold down the and press

F10 again. The cursor control mode light goes out.

Shift while you use the numeric

Fn key

Learning the Basics

Emulating a full-size keyboard

Although the computer’s keyboard layout is compatible with a standard full-size keyboard, it has fewer keys.

Pressing the of the specially marked keys allows you to emulate a full-size keyboard. For further information and instructions, see

“Assigning a key to a program or document” on page 189.

NOTE: The Fn emulation key is not supported when using a USB keyboard.

Fn key simultaneously in combination with one

TOSHIBA Console button

The TOSHIBA Console button provides quick access to some common functions. When the default setting is active, the TOSHIBA Console button brings up the TOSHIBA Console.

Sample TOSHIBA Console window

For information on how to program the button, see

“TOSHIBA Console” on page 192.

Starting a program

The easiest way to start a program is to click the name of the file that contains the information you want to work on. To find the file, use My Computer or Windows

If you prefer to open the program first, you have four options:

❖ Double-click the icon for the program on your desktop

❖ Use the Start menu

❖ Use Windows

program file

❖ Use the Run window

The tutorial chapter for the Windows gives step-by-step instructions for starting a program from the Start menu. See “Lesson 6: Starting programs” on

page 143.

Learning the Basics

Starting a program

Explorer.

Explorer or My Computer to locate the

XP operating system

Saving your work

Before you turn off the computer, save your work to the hard disk drive or a diskette. This is one of the most important rules of computing.

NOTE: Save your data even when you are using the Standby command, in case the battery discharges before you return to work. Your computer can be configured to warn you when the battery is running low, see “Setting battery alarms” on page 125.

Many programs offer a feature that saves documents at regular intervals, such as every 15 minutes. Check your programs’ documentation to see whether they have an automatic save feature.

Learning the Basics

Printing your work

To save :

❖ A file you are updating, open the program’s File menu

and click Save.

❖ A new file, choose Save As from the File menu, type a

name for the file, and click OK.

HINT: To make another copy of the file you are currently working with, choose Save As from the File menu and give the new file a different name.

Printing your work

Verify that the operating system is set up for your printer as described in “Setting up a printer” on page 68.

TECHNICAL NOTE: You only need to set up the printer the first time you connect it. If you use more than one printer or are changing printers, you will need to set up the operating system to run with the additional printer(s).

To print a file:

1 If your printer is not on, turn it on now.

2 In the File menu of your Windows

Print.

The program displays a Print window.

program, click

Sample Print window

Learning the Basics

Using diskettes

3 Click OK or Print to print.

Using diskettes

The 3.5-inch internal or external diskette drive lets you use high-density (1.44 MB) diskettes for data transfer and storage.

Sample diskette drive

The diskette drive LED flashes while the drive is being accessed.

Eject buttonDiskette drive LED

Learning the Basics

Using diskettes

Inserting and removing diskettes

1 Hold the diskette so that the arrow on its upper surface

points toward the drive.

2 Push the diskette gently into the drive slot. When the

diskette is in place, the eject button pops out.

To release a diskette from the drive, push the eject button.

CAUTION: Never press the eject button or turn off the computer while the diskette drive LED is flashing. Doing so could destroy data and damage the diskette or the drive.

To access your diskette contents:

1 Click Start, then click My Computer.

2 Double-click the 3 1/2 Floppy (A:) drive.

The diskette contents appear.

Caring for diskettes

❖ Store your diskettes properly to protect them and keep

them clean.

❖ If a diskette is dirty, clean it with a soft cloth moistened

in water. Do not use cleaning fluids.

❖ Never slide back the protective metal cover.

❖ Never touch the magnetic surface of a diskette.

Fingerprints can prevent the drive from reading the data stored on a diskette.

❖ Never twist or bend a diskette.

❖ Keep diskettes at room temperature and avoid exposing

them to direct sunlight. Otherwise data may be lost.

❖ Never place heavy objects on your diskettes.

❖ Never eat, smoke, or use erasers near your diskettes.

Foreign particles can damage the diskette’s surface.

❖ Keep your diskettes away from sources of magnetism,

such as speakers and radios, since these can destroy data.

Backing up your files

Backing up your files means copying individual files to a diskette or copying entire sections of your hard disk to another device, such as a tape drive, or to your network partition.

Copying to a diskette

1 Insert a diskette into the diskette drive.

2 Click Start.

The Start menu appears.

3 Click My Computer.

Learning the Basics

Backing up your files

The My Computer window appears.

4 Double-click the drive that contains the file you want to

copy.

5 Double-click the folder that contains the file, then click

the file you want to copy.

HINT: You can use the Ctrl or Shift keys to select more than one file.

6 Click File, then click Send To.

Learning the Basics

Playing a CD or DVD

7 Click the icon for the diskette drive (3 1/2 floppy [A:]).

HINT: You can also back up a file to a diskette by clicking the file (or files) you want to backup with the secondary button, then pointing to Send To and clicking 3 1/2 Floppy (A:).

Playing a CD or DVD

Your computer may have a DVD-ROM or multi-function drive that can read both DVD-ROM and CD-ROM discs.

Digital versatile discs (DVDs) provide a significant increase in data storage and support features that are not available on any other video platform. These features include wide-screen movies, multiple language tracks, digital surround sound, multiple camera angles, and interactive menus. The computer can play high-resolution video at up to 30 frames per second.

NOTE: For optimum DVD performance, it is recommended that you play DVDs while running on AC power rather than battery power.

You use CD-ROMs to load and run software, and to access reference material such as catalogs, as well as listen to music.

A special feature allows you to play audio CDs even when the computer is turned off. For more information, see “CD/

DVD control buttons” on page 88.

If your computer has a DVD-ROM or multi-function drive, you can also write files (including music) to a CDRecordable (CD-R) or CD-ReWritable (CD-RW) disc.

Learning the Basics

Playing a CD or DVD

Drive components and control buttons

The CD/DVD control buttons are located at the front edge of the computer and can be accessed when the display panel is closed or open.

Components

DVD-ROM or multi-function drive (Sample Drive)

Sample DVD-ROM or multi-function drive

Use the eject button to open the disc tray. This button requires power to operate.

CAUTION: Never press the eject button or turn off the computer while the disk/disc activity light is flashing. Doing so could damage the disc or the drive.

Eject button

Manual

eject button

Learning the Basics

Playing a CD or DVD

The manual eject button allows you to manually open the disc tray when power to the computer and the drive is off.

CAUTION: Never use a pencil to press the manual eject button. Pencil lead can break off inside the computer and damage it. Instead, use a slim object such as a straightened paper clip.

HINT: When the computer is off and the DVD-ROM or multi-function drive is on, press the stop/eject control button to eject a disc.

CD/DVD control buttons

The control buttons on the front edge of the computer enable you to play audio CDs when the computer is off. You can also use them to play CDs and DVDs when the computer is on.

CD/ DVD

mode

Digital audio mode

track

Play/Pause

Stop/Eject

track

CD/DVD control buttons

The CD/DVD mode button allows you to play CDs or DVDs in the DVD-ROM or multi-function drive.

The Digital audio mode button allows you to play digital audio files.

The previous track button returns to the preceding track on the disc.

The play/pause button starts playing the disc or makes it pause if currently playing.

The stop/eject button stops a disc that is currently playing.

The next track button skips to the following track on the disc.

You can eject a disc by pressing the stop/eject button twice. Use this method to eject a disc when the computer is turned off and the sound subsystem is turned on.

NOTE: If you have set a password for logging onto your system, your computer will start up and you will need to log on before being able to play a CD or DVD.

CD/DVD and Digital audio modes

The following chart describes CD/DVD mode and Digital audio mode.

CD /DVD mode Digital audio mode

Power is off and you press Play/ Pause

If an audio CD is in the drive, the system enters CD player mode and operates as a stand-alone CD player.

Learning the Basics

Playing a CD or DVD

The operating system starts, the Toshiba Media Player starts and the digital audio files begin to play.

Power is on, operating system is running and you press Play/ Pause

If a DVD is in the drive, the operating system starts and the DVD player starts.

If an audio CD is in the drive, the Toshiba Media Player starts and the audio files begin to play.

If a DVD is in the drive, WinDVD DVD begins to play.

starts and the

Toshiba Media Player starts and the digital audio files begin to play.

Learning the Basics

Playing a CD or DVD

CAUTION: Do not install or remove a memory module while the DVD-ROM or multi-function drive power is on.

Inserting a disc

WARNING: Before playing an audio CD or a DVD, turn the volume down. Playing the disc at maximum volume could damage your ears. To turn the volume down, use the volume control dial or access the Volume Control program (click Start, All Programs, Accessories, Entertainment, Volume Control).

1 If the computer is turned on, press the eject button on the

DVD-ROM or multi-function drive.

Eject button

The disc tray partially opens.

CAUTION: To avoid damaging a disc or losing data, check that the disk/disc activity light is off before opening the disc tray.

2 Grasp the disc tray and pull it fully open.

Learning the Basics

Playing a CD or DVD

3 Hold the disc by its edges and check that it is clean and

free of dust.

CAUTION: Handle discs carefully. Avoid touching the surface of the disc. Grasp it by its center hole and edge. If you handle the disc incorrectly, you could lose data.

4 Carefully place the disc in the empty tray with its label

facing up.

Inserting a disc

CAUTION: Be careful not to touch the drive’s lens (located underneath the drive’s spindle) or the area around it. Doing so could cause the drive to malfunction.

Learning the Basics

Playing a CD or DVD

5 Gently press the center of the disc onto the spindle until it

locks into place.

Spindle

Disc

Positioning the disc on the spindle

CAUTION: Make sure the disc is properly positioned on the spindle. If you position the disc incorrectly, it can jam the disc tray.

6 Close the disc tray by pressing gently on the center of the

tray until it clicks, indicating that it is locked.

Playing an audio CD

Insert an audio CD and close the disc tray.

Correct position

Incorrect position

Learning the Basics

Playing a CD or DVD

The computer automatically detects a disc in the drive and opens the Audio CD window. To play an audio CD select the Play Audio CD using Windows Media Player option and click OK.

Sample Audio CD window

The Windows Media Player window appears.

Learning the Basics

Playing a CD or DVD

Rewind Play Stop Previous track Next track Mute

Sample Windows MediaTM Player screen

Volume control

Viewing the contents of a CD or DVD

CDs and DVDs contain files just like diskettes and the hard disk. CDs are often used to install software or store files that require a lot of space, such as photographs and large presentation files. You can use Explorer or My Computer to view the contents of any CD or DVD.

Fast forward

Learning the Basics

Playing a CD or DVD

Removing a disc with the computer on

CAUTION: Never press the eject button while the computer is accessing the drive. Wait for the disk/disc activity light on the system indicator panel to turn off before opening the disc tray.

1 Locate and press the eject button.

The disc tray partially opens.

2 Grasp the sides of the disc tray and pull it fully open.

3 Remove the disc from the disc tray and place it in its

protective cover.

CAUTION: If the disc is spinning when you open the disc tray, wait for the disc to stop before removing it.

4 Close the disc tray by pressing gently on the center of the

tray until it clicks indicating that it is locked.

Removing a disc with the computer off

1 Insert a slender object, such as a straightened paper clip,

into the manual eject button access hole.

CAUTION: Never use a pencil to press the manual eject button. Pencil lead can break off inside the computer and damage it.

2 Pull the tray fully open, remove the disc and place it in its

protective cover.

3 Close the disc tray by pressing gently on the center of the

tray until it clicks indicating that it is locked.

Learning the Basics

Using the DVD-ROM or multi-function drive

Caring for CDs and DVDs

❖ Store your discs in their original containers to protect

them from scratches and keep them clean.

❖ Never bend a disc or place heavy objects on top of it.

❖ Hold a disc by its outside edge. Fingerprints on the

surface of a disc can prevent the drive from reading the data properly.

❖ Avoid exposing discs to direct sunlight or extreme heat or

cold.

❖ To clean a disc, wipe it from the center outwards (not in a

circle) with a clean, dry cloth. If necessary, moisten the cloth with water or a neutral cleaner (not benzine or rubbing alcohol). Let the disc dry completely before inserting it in the drive.

Using the DVD-ROM or multi-function drive

Your computer may come with a DVD-ROM or multi-function drive that allows you to:

❖ Play prerecorded DVDs

(DVD-ROM or multi-function drive)

❖ Play prerecorded CDs

❖ Read and write files (including music) to a CD-

Recordable (CD-R) or CD-ReWritable (CD-RW) disc.

CAUTION: Check the disk/disc activity light when you use the DVD-ROM or multi-function drive. Do not press the eject button, disconnect a drive or turn off the computer while the light is flashing. Doing so could damage the CD, DVD or drive.

Learning the Basics

Setting up for communications

To communicate across the telephone lines with another computer, you need:

❖ The computer’s modem

❖ A telephone line

❖ A communications program

To connect to the Internet, you need a Web browser, such as Microsoft

Internet Explorer.

TECHNICAL NOTE: Disable Call Waiting before you connect through the modem. Call Waiting interrupts data transmission.

Connecting the modem

Your computer comes with a built-in modem and a built-in Ethernet LAN adapter. To use the modem, you must connect it to a standard voice-grade RJ11 telephone line.

NOTE: Due to FCC limitations, speeds of 53 kbps are the maximum permissible rates during downloads. Actual data transmission speeds will vary depending on line conditions.

1 Attach one end of a standard RJ11 telephone cable to the

modem port on the back of the computer.

Learning the Basics

Setting up for communications

Connecting to the modem port

2 Plug the other end of the RJ11 telephone cable into the

modular jack of a standard voice-grade telephone line.

Connecting your computer to a network

You can connect your computer to a network locally or remotely.

❖ Locally, using the built-in Ethernet LAN adapter by

connecting it to a standard RJ45 LAN line.

❖ Remotely, using the built-in modem and a dial-up

connection.

To set up the network connection, use the Network Setup Wizard:

1 Click Start and point to All Programs.

2 Point to Accessories, then to Communications, and

click Network Setup Wizard.

3 Follow the on-screen instructions.

The computer connects with the network.

Learning the Basics

Powering down the computer

When you power down the computer, you have a number of options to choose from:

❖ Turn Off or Shut down, which power off the computer

❖ Hibernation, which saves the current operating state to

the hard disk and powers off the computer

❖ Standby, which saves the current operating state to

memory and enters a low power mode

❖ Restart, which restarts the computer

Each option has its advantages.

TECHNICAL NOTE: Before using any of these options to power down your computer, save your files and make sure the disk activity lights are off.

If you change your mind and decide to continue working after all, wait a few seconds before turning the computer on again.

Turn Off or Shut down command

The Turn Off or Shut down commands power off the computer. The Windows the Turn Off command. The Windows operating system uses the Turn Off command if you are not connected to a Windows Professional operating system uses the Shut down command if you are a member of a domain.

Factors to consider when choosing Turn Off or Shut down:

❖ No power is used while the computer is turned off. This

is the most efficient mode if you will be away from your computer for an extended time.

❖ Restarting from Turn Off or Shut down uses the most

time and battery power.

XP Home operating system uses

domain server. The Windows® XP

XP Professional

Learning the Basics

100

Powering down the computer

❖ When starting up again, the system does not

automatically open the programs and files you were previously using.

Restart command

Restart is the same as Turn Off or Shut down but automatically powers up the computer. Use it when you need to reload the operating system, for example to activate changes to system settings.

Hibernation command

The Hibernation command powers off the computer, but it first saves the current state of the computer to the hard disk. Since Hibernation does not require power to maintain the saved information, the system settings are retained indefinitely. Restoring information from the hard disk takes longer than restoring it from memory. When you restart the computer, the computer runs a self-test, loads the operating system, and then returns to the state in which you left it.

Factors to consider when choosing Hibernation:

❖ While in Hibernation mode, the computer uses no battery

power.

❖ Because the state of the system is held on the hard disk,

no data is lost if the battery discharges while the computer is in Hibernation mode.

❖ When starting up again, this choice uses less time and

battery power than the Turn Off or Shut down option. But it uses a little more time and battery power to start up than the Standby mode, because information is being retrieved from the hard disk instead of from memory.

❖ On restarting, the computer returns to the state in which

you left it, and opens all the programs and files you were using.

Toshiba 2415 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Contents

Introduction

This guide

Safety icons

Other documentation

Other icons used

Service options

Making sure you have everything

Front with the display closed

Back

Right side

Left side

Front with the display open

Keyboard indicator lights

System indicator panel

CD/DVD control buttons

Underside

Selecting a place to work

Creating a computer-friendly environment

Keeping yourself comfortable

Precautions

Setting up your computer

Setting up your software

Registering your computer with Toshiba

Adding external devices

Installing additional memory (optional)

Connecting a mouse

Connecting a printer

Connecting a USB printer

Connecting a parallel printer

Using external display devices

Connecting an external monitor

Adjusting the quality of the external display

Display limitations

Connecting an external diskette drive

Using an external keyboard

Connecting to a power source

Charging the battery

Using the computer for the first time

Opening the display panel

Turning on the power

Activating the power-on password

Important information on your computer’s built-in LCD sensor

Using the TouchPad

Primary and secondary control buttons

Disabling or enabling the TouchPad

Setting up a printer

Setting up the fax function

Powering off the computer

Caring for your computer

Cleaning the computer

Moving the computer

Using a computer lock

Computing tips

Using the keyboard

Character keys

Ctrl, Fn, and Alt keys

Function keys

Overlay keys

Emulating a full-size keyboard

TOSHIBA Console button

Starting a program

Saving your work

Printing your work

Using diskettes

Inserting and removing diskettes

Caring for diskettes

Backing up your files

Copying to a diskette

Playing a CD or DVD

Drive components and control buttons

CD/DVD control buttons

CD/DVD and Digital audio modes

Inserting a disc

Playing an audio CD

Viewing the contents of a CD or DVD